Yamaha | RX-V683 | Owner’s Manual | Owner`s Manual - Yamaha Corporation

AV Receiver
Owner’s Manual
• This unit is a product for enjoying video and music at home.
• This manual explains preparations and operations for everyday users of the unit.
• Read the supplied booklet “Quick Start Guide” before using the unit.
EN
CONTENTS
Introduction
5
Preparing the wireless antenna ...................................................................................................................35
5 Connecting a device compatible with the trigger function .............36
Accessories................................................................................... 5
6 Connecting the power cable ........................................................37
About this book ............................................................................ 5
7 Selecting an on-screen menu language ........................................38
About remote control .................................................................... 5
8 Configuring the necessary speaker settings..................................39
Batteries ......................................................................................................................................................... 5
9 Optimizing the speaker settings automatically (YPAO) ..................40
Operating range of the remote control......................................................................................................... 5
Checking the measurement results .............................................................................................................43
Reloading the previous YPAO adjustments.................................................................................................43
FEATURES
6
Error messages .............................................................................................................................................44
What you can do with the unit ........................................................ 6
10 Connecting to a network device wirelessly .................................46
Part names and functions .............................................................. 9
Selecting the connection method ...............................................................................................................46
Warning messages ........................................................................................................................................45
Connecting the unit to a wireless network..................................................................................................47
Front panel ..................................................................................................................................................... 9
Connecting a mobile device to the unit directly (Wireless Direct) .............................................................52
Front display (indicators) ............................................................................................................................ 11
Rear panel..................................................................................................................................................... 12
11 Connecting to the MusicCast network ........................................54
Remote control ............................................................................................................................................ 14
MusicCast CONTROLLER ..............................................................................................................................54
Adding the unit to the MusicCast network ..................................................................................................54
PREPARATIONS
15
PLAYBACK
55
General setup procedure ..............................................................15
Basic playback procedure .............................................................55
1 Connecting speakers ..................................................................16
Selecting an HDMI output jack.....................................................................................................................55
Basic speaker configuration ........................................................................................................................ 17
Selecting the input source and favorite settings with one touch
(SCENE) ......................................................................................56
Advanced speaker configuration ................................................................................................................ 23
2 Connecting a TV and playback devices .........................................28
Registering a scene .......................................................................................................................................56
Input/output jacks and cables .................................................................................................................... 28
Connecting a TV ........................................................................................................................................... 29
Selecting the sound mode.............................................................57
Connecting video devices (such as BD/DVD players) ................................................................................. 30
Enjoying stereoscopic sound fields (CINEMA DSP 3D) ................................................................................58
Connecting audio devices (such as CD players) ......................................................................................... 33
Enjoying unprocessed playback ..................................................................................................................61
Connecting to the jacks on the front panel ................................................................................................ 33
Enjoying pure high fidelity sound (Pure Direct) ..........................................................................................62
3 Connecting the FM/AM antennas..................................................34
Playing back digitally compressed formats (such as MP3, etc.) with enriched sound
(Compressed Music Enhancer).....................................................................................................................62
4 Connecting a network cable or preparing the wireless antenna......35
Listening to FM/AM radio ..............................................................63
Connecting the network cable .................................................................................................................... 35
En
2
CONFIGURATIONS
Setting the frequency steps......................................................................................................................... 63
Selecting a frequency for reception ............................................................................................................ 63
Registering favorite radio stations (presets) .............................................................................................. 64
94
Configuring input sources (Input menu).........................................94
Radio Data System tuning ........................................................................................................................... 65
Input menu items .........................................................................................................................................94
Operating the radio on the TV ..................................................................................................................... 66
Configuring the SCENE function (Scene menu) ...............................96
Playing back music via Bluetooth ..................................................67
Scene menu items ........................................................................................................................................97
Playing back Bluetooth device music on the unit ...................................................................................... 67
Configuring sound programs/surround decoders
(DSP Program menu) ................................................................. 100
Enjoying audio using Bluetooth speakers/headphones ............................................................................ 68
Playing back music stored on a USB storage device.........................69
DSP Program menu items ..........................................................................................................................101
Connecting a USB storage device ............................................................................................................... 69
Configuring various functions (Setup menu) ................................ 103
Playback of USB storage device contents .................................................................................................. 69
Setup menu items.......................................................................................................................................104
Playing back music stored on media servers (PCs/NAS) ...................72
Speaker (Manual Setup) .............................................................................................................................107
Media sharing setup..................................................................................................................................... 72
Sound ..........................................................................................................................................................110
Playback of PC music contents ................................................................................................................... 73
Video............................................................................................................................................................112
Listening to Internet radio ............................................................76
HDMI ............................................................................................................................................................113
Playback of Internet radio ........................................................................................................................... 76
Network.......................................................................................................................................................115
Registering favorite Internet radio stations (Favorites) ............................................................................. 78
Bluetooth ....................................................................................................................................................117
Playing back iTunes/iPhone music with AirPlay ..............................79
Multi Zone ...................................................................................................................................................118
Playback of iTunes/iPhone music contents................................................................................................ 79
Function ......................................................................................................................................................120
Playing back music in multiple rooms (multi-zone) .........................81
ECO ..............................................................................................................................................................122
Preparing Zone2........................................................................................................................................... 81
Language.....................................................................................................................................................123
Controlling Zone2 ........................................................................................................................................ 83
Viewing information about the unit (Information menu) ............... 123
Registering favorite items (shortcut) .............................................85
Types of information ..................................................................................................................................124
Registering an item ...................................................................................................................................... 85
Configuring the system settings (ADVANCED SETUP menu)............ 125
Recalling a registered item .......................................................................................................................... 85
ADVANCED SETUP menu items ..................................................................................................................126
Controlling the unit from a web browser (web control) ...................86
Changing the speaker impedance setting (SP IMP.) .................................................................................126
Top menu screen.......................................................................................................................................... 87
Selecting the remote control ID (REMOTE ID) ...........................................................................................126
Control screen .............................................................................................................................................. 87
Changing the FM/AM tuning frequency setting (TU).................................................................................126
Settings screen............................................................................................................................................. 88
Switching the video signal type (TV FORMAT)...........................................................................................127
Removing the limitation on HDMI video output (MON.CHK)....................................................................127
Viewing the current status ............................................................89
Selecting the HDMI 4K signal format (4K MODE).......................................................................................127
Switching information on the front display................................................................................................ 89
DTS Format Notification Setting (DTS MODE)...........................................................................................128
Viewing the status information on the TV................................................................................................... 89
Restoring the default settings (INIT)..........................................................................................................128
Configuring playback settings for different playback sources
(Option menu) .............................................................................90
Updating the firmware (UPDATE) ..............................................................................................................128
Checking the firmware version (VERSION) ................................................................................................128
Option menu items ...................................................................................................................................... 90
Updating the unit’s firmware via the network .............................. 129
Updating the unit’s firmware immediately ...............................................................................................129
En
3
Updating the unit’s firmware at power off ............................................................................................... 130
APPENDIX
131
Frequently asked questions ........................................................ 131
Troubleshooting ........................................................................ 132
First, check the following:.......................................................................................................................... 132
Power, system and remote control........................................................................................................... 132
Audio........................................................................................................................................................... 133
Video ........................................................................................................................................................... 135
FM/AM radio................................................................................................................................................ 136
Bluetooth.................................................................................................................................................... 137
USB and network ....................................................................................................................................... 137
Error indications on the front display .......................................... 139
Glossary .................................................................................... 140
Audio information (audio decoding format) ............................................................................................ 140
Audio information (others) ........................................................................................................................ 141
HDMI and video information ..................................................................................................................... 142
Network information ................................................................................................................................. 142
Yamaha technologies................................................................................................................................. 142
Supported devices and file formats ............................................. 143
Supported devices ..................................................................................................................................... 143
File formats................................................................................................................................................. 143
Video signal flow........................................................................ 144
Video conversion table .............................................................................................................................. 144
Information on HDMI .................................................................. 145
HDMI Control .............................................................................................................................................. 145
Audio Return Channel (ARC)...................................................................................................................... 146
HDMI signal compatibility.......................................................................................................................... 147
Trademarks ............................................................................... 148
Specifications ............................................................................ 149
En
4
Introduction
Accessories
Check that the following accessories are
About remote control
☐ YPAO microphone
This section explains how to use the supplied remote control.
supplied with the product.
☐ AM antenna
Batteries
Insert the batteries the right way round.
☐ Remote control
☐ FM antenna
☐ Batteries (AAA, R03, UM-4) (x2)
☐ CD-ROM (Owner’s Manual)
☐ Quick Start Guide
Operating range of the remote control
* One of the above is supplied depending on the
region of purchase.
X
Point the remote control at the remote control sensor on the unit and remain within the operating range shown
below.
About this book
• In this manual, illustrations of English menu screens are used as examples.
Within
6 m (20 ft)
• Some features are not available in certain regions.
• Due to product improvements, specifications and appearance are subject to change without
30°
notice.
• This manual explains operations using the supplied remote control.
• This manual describes all the “iPod touch”, “iPhone” and “iPad” as the “iPhone”. “iPhone”
refers to “iPod touch”, “iPhone” and “iPad”, unless otherwise specified.
Icons used in this manual
Y
indicates precautions for use of the unit and its feature limitations.
X
indicates supplementary explanations for better use.
En
5
30°
FEATURES
What you can do with the unit
The unit is equipped with the various useful features.
Various wireless connection
methods (p.46)
Creating 3-dimensional sound fields
(p.58)
Connecting various devices (p.28)
The unit supports the Wi-Fi feature that allows the unit to
Connecting presence speakers allows you to create a natural
A number of HDMI jacks and various input/output jacks on
connect to your wireless router (access point) without a
3-dimensional sound field in your own room (CINEMA DSP
the unit allow you to connect video devices (such as BD/DVD
network cable connection. In addition, Wireless Direct
3D). Even when no presence speakers are connected, the
players), audio devices (such as CD players), game consoles,
enables connecting a mobile device to the unit directly
Virtual Presence Speaker (VPS) function produces 3D
camcorders, and other devices.
without router.
surround sound. In addition, the unit creates Virtual
Surround Back Speaker (VSBS) using the surround speakers
to add a sense of depth to the rear sound field even when no
Playing back TV audio in surround
sound with a single HDMI cable
connection (Audio Return Channel:
ARC) (p.29)
surround back speakers are connected.
Wi-Fi or
Wireless Direct
When using an ARC-compatible TV, you only need one HDMI
cable to enable video output to the TV, audio input from the
TV, and the transmission of HDMI Control signals.
HDMI Control
TV audio
VSBS
Video from
external device
En
6
Surround playback with 5 speakers
placed in front (p.60)
If you have surround speakers but there is no space to place
Useful applications
The following applications provide you the flexibility to control the unit or assist you with the cable connections.
⬛ AV CONTROLLER
⬛ AV SETUP GUIDE (for tablet)
“AV CONTROLLER” will turn your smartphone/tablet into a
“AV SETUP GUIDE” is an application that assists you with
Wi-Fi enabled remote control for your Yamaha network
cable connections between AV receiver and source devices
The unit supports the MusicCast feature that allows you to
products. This application provides you the flexibility to
as well as AV receiver setup. This application guides you
link a MusicCast compatible device to another device in a
control the available inputs, volume, mute, power
through the various settings such as speaker connections,
different room and play them back simultaneously, or
commands and playback source.
TV and video/audio device connections and selecting the
them in the rear of your room, you can place them in the
front and enjoy multichannel surround sound with the 5
speakers placed in the front (Virtual CINEMA FRONT).
Home Audio Network with
MusicCast (p.54)
speaker system.
control all MusicCast compatible devices with the dedicated
application “MusicCast CONTROLLER”.
Functions
• Power on/off and volume adjustment
Functions
Low power consumption (p.122)
• Input, scene and sound mode selection
• Connection guide (speakers, TV and video/audio devices)
• DSP Parameter adjustment
• Setup guide (YPAO settings and various setup assistance
The ECO mode (power saving function) reduces the unit’s
• Playback control (including music selection for some
power consumption.
with illustrations)
• Viewing owner’s manual
sources)
X
X
For details, search for “AV CONTROLLER” on the App Store or Google
For details, search for “AV SETUP GUIDE” on the App Store or Google
Play.
Play.
En
7
⬛ Application for smartphone /
tablets "MusicCast CONTROLLER"
MusicCast CONTROLLER is an application that allows you to
link a MusicCast compatible device to other MusicCast
compatible devices in other rooms and play them back
simultaneously. This app lets you use your smartphone or
other mobile device instead of the remote control to easily
select music to play back as well as configure the unit and
MusicCast compatible devices.
Functions
• Selecting and playing back various content
– Play back music from your mobile device
– Select an Internet radio station
– Play back music files stored on media servers (PCs/NAS)
– Play back music files stored on a USB storage device
• Operating and configuring the unit
– Select the input source, adjust the volume and mute the
audio output
– Select from a wide variety of sound processing features
X
For details, search for “MusicCast CONTROLLER” on the App Store or
Google Play.
En
8
Part names and functions
This section explains the functions of the parts of the unit.
Front panel
a
b
MAIN ZONE
c
d
e
f
g
h
i
j
k
l
m
YPAO MIC
PURE DIRECT
ZONE 2
ZONE CONTROL
INFO (WPS)
MEMORY
PRESET
FM
AM
TUNING
VOLUME
SCENE
1
PHONES
SILENT CINEMA
n
USB
5V
INPUT
2
TONE CONTROL
3
PROGRAM
4
(CONNECT)
1A
o
p
q
r
s
En
9
VIDEO AUX
STRAIGHT
t
HDMI IN
AUDIO
u
v
w
a MAIN ZONE z key
r SCENE keys
Turns on/off (standby) the unit.
Select the assigned input source (included the selected radio station or content when it is assigned),
sound program, and various settings with one touch. Also, turns on the unit when it is in standby mode
(p.56).
b Standby indicator
Lights up when the unit is in standby mode under any of the following conditions.
s PROGRAM keys
• HDMI Control is enabled (p.113)
Select a sound program or a surround decoder (p.57).
• Standby Through is enabled (p.114)
t STRAIGHT (CONNECT) key
• Network Standby is enabled (p.115)
Enables/disables the straight decode mode (p.61).
c YPAO MIC jack
Enters MusicCast CONTROLLER registration by holding down for 5 seconds (p.54).
For connecting the supplied YPAO microphone (p.40).
u HDMI IN jack
d ZONE 2 key
For connecting to HDMI-compatible playback devices and inputting video/audio signals (p.33).
Enables/disables the audio output to Zone2 (p.83).
v AUDIO jack
e Remote control sensor
Connect a portable audio player to the unit with a stereo mini-cable (p.33).
Receives remote control signals (p.5).
w VOLUME knob
f ZONE CONTROL key
Adjusts the volume.
Changes the zone (main zone or the Zone2) that is controlled by the keys and knobs on the front panel
(p.83).
g INFO (WPS) key
Selects the information displayed on the front display (p.89).
Enters the wireless network connection setup (WPS push button configuration) by holding down for 3
seconds (p.48).
h MEMORY key
Registers FM/AM radio stations (p.64) and USB, Bluetooth, and network content (p.85) as presets.
i PRESET keys
Select a preset FM/AM radio station (p.64).
j FM and AM keys
Switch between FM and AM (p.63).
k Front display
Displays information (p.11).
l TUNING keys
Select the radio frequency (p.63).
m PURE DIRECT key
Enables/disables Pure Direct (p.62).
n PHONES jack
For connecting headphones.
o USB jack
For connecting a USB storage device (p.69).
p INPUT keys
Select an input source.
q TONE CONTROL key
Adjusts the high-frequency range and low-frequency range of output sounds (p.91).
En
10
Front display (indicators)
ab
c
de
g
h
i j k
l
m
STEREO TUNED ZONE
SLEEP PARTY 2 3 B
Hi -Res ENHANCER YPAO VOL. A - DRC
LINK MASTER
OUT
f
2
ECO
VOL. MUTE VIRTUAL
FPL
FPR
SW
SR
SL
SBL SB SBR
n
a ECO
Lights up when the unit is in the eco mode (p.122).
b HDMI
Lights up when HDMI signals are being input or output.
OUT
Lights up when HDMI signals are being output.
c LINK MASTER
Lights up when the unit is the master device of the MusicCast
network.
d Firmware update indicator
Lights up when a firmware update is available via the network.
(p.129)
e Bluetooth indicator
Lights up when the unit is connecting to a Bluetooth device (p.67).
f CINEMA DSP
Lights up when CINEMA DSP or CINEMA DSP 3D (p.58) is working.
g SLEEP
Lights up when the sleep timer is on.
h STEREO
Lights up when the unit is receiving a stereo FM radio signal.
TUNED
o
p
q
k A-DRC
r
n
s t
t Speaker indicators
Lights up when Adaptive DRC (p.91) is working.
Indicate speaker terminals from which signals are output.
A Front speaker (L)
l Volume indicator
Indicates the current volume.
S Front speaker (R)
D Center speaker
m VIRTUAL
Lights up when the Virtual Presence Speaker (VPS) or Virtual
Surround Back Speaker (VSBS) (p.58), or the virtual surround
processing (p.60) is working.
n Cursor indicators
F Surround speaker (L)
G Surround speaker (R)
H Surround back speaker (L)
J Surround back speaker (R)
Indicate the remote control cursor keys currently operational.
o Information display
B Presence speaker (L)
Displays the current status (such as input name and sound mode
name). You can switch the information by pressing INFO (p.89).
p Signal strength indicator
Indicates the strength of the wireless network signal (p.46).
q ENHANCER
Lights up when Compressed Music Enhancer (p.62) is working.
r YPAO Volume
Lights up when YPAO Volume is enabled (p.91).
s MUTE
Blinks when audio is temporarily muted.
Lights up when the unit is receiving an FM/AM radio station signal.
i PARTY
Lights up when the unit is in the party mode (p.84).
j ZONE2
Lights up when audio output to Zone2 is enabled (p.83).
En
K Surround back speaker
11
N Presence speaker (R)
L Subwoofer
Rear panel
a
b
c
d
e
f
g
h
TRIGGER OUT
12V 0.1A
HDMI (HDCP2.2)
HDMI OUT
(HDCP2.2)
IN
OUT
HDMI
NETWORK
(3 NET)
1
2
3
4
5
(1 BD/DVD)
ARC
REMOTE
ANTENNA
(4 RADIO)
AUDIO 1
(2 TV)
FM
OPTICAL
AM
AUDIO 2
OPTICAL
SPEAKERS
AUDIO 3
AV 2
COMPONENT VIDEO
COAXIAL
COAXIAL
AV 1
Y
VIDEO
SURROUND
FRONT
EXTRA SP2
SURROUND BACK
/ ZONE2 / BI-AMP
SINGLE
EXTRA SP1
F.PRESENCE
/ ZONE2
PR
PB
ZONE OUT
AUDIO 4
PHONO
CENTER
ZONE 2
AUDIO 5
PRE OUT
SUBWOOFER
1
GND
2
CLASS 2 WIRING
CÂBLAGE CLASSE 2
kl
k
m
n
o
* The area around the video/audio output jacks is marked in white on the actual product to prevent improper
connections.
En
12
i
j
a REMOTE IN/OUT jacks
For connecting to an infrared signal receiver/emitter that allows you to operate the unit and other
devices from another room (p.82).
b TRIGGER OUT jack
For connecting to a device that supports the trigger function (p.36).
c ANTENNA jacks
For connecting to FM and AM antennas (p.34).
d HDMI OUT jack
For connecting to an HDMI-compatible TV and outputting video/audio signals (p.29). When using ARC, TV
audio signal can also be input through the HDMI OUT jack.
e HDMI 1-5 jacks
For connecting to HDMI-compatible playback devices and inputting video/audio signals (p.30).
f Wireless antenna
For a wireless (Wi-Fi) connection to a network (p.46) and a Bluetooth connection (p.67).
g NETWORK jack
For connecting to a network with a network cable (p.35).
h SPEAKERS terminals
For connecting to speakers (p.16).
i VOLTAGE SELECTOR
(Taiwan, Brazil and General models only)
Selects the switch position according to your local voltage (p.37).
j Power cable
For connecting to an AC wall outlet (p.37).
k AUDIO 1-5 jacks
For connecting to audio playback devices and inputting audio signals (p.33).
l PHONO jacks
For connecting to a turntable (p.33).
m AV 1-2 jacks
For connecting to video/audio playback devices and inputting video/audio signals (p.30).
n ZONE2 OUT jacks
For connecting to the external amplifier used in Zone2 and for outputting audio (p.81).
o SUBWOOFER PRE OUT jacks
For connecting to a subwoofer with built-in amplifier.
En
13
Remote control
a Remote control signal transmitter
a
Transmits infrared signals.
Turns on/off (standby) the unit.
HDMI
1
2
3
4
5
c
Operate the FM/AM radio when “TUNER” is selected as the input
source (p.63).
b z (receiver power) key
b
Select an input source for playback.
AUDIO
1
2
3
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
e
MAIN
ZONE 2
o
p
SCENE
2
1
3
4
External device operation keys
V-AUX: VIDEO AUX jack (on the front panel)
Let you perform playback operations when “USB” or “NET” is
selected as the input source, or control playback of the HDMI
Control-compatible playback device (p.145).
AUDIO 1-5: AUDIO 1-5 jacks
k Sound mode keys
TUNER: FM/AM radio
BLUETOOTH: Bluetooth connection (the unit as a Bluetooth
receiver)
USB: USB jack (on the front panel)
f
PROGRAM MUTE
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
i
s
ENTER
DISPLAY
BAND
MODE
j
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
ENHANCER PURE DIRECT
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
NET: NETWORK sources (press repeatedly to select a desired
network source)
PHONO: PHONO jacks
d MAIN/ZONE2 switch
Changes the zone (main zone or Zone2) that is controlled by the
remote control (p.83).
MEMORY
ENT
t
Select a sound mode (p.57).
l INFO key
Selects the information displayed on the front display (p.89).
m SLEEP key
Pressing this key repeatedly will specify the time (120 min, 90 min,
60 min, 30 min, off), in which the unit switches to the standby
mode.
n Numeric keys
Let you enter numerical values, such as radio frequencies.
MEMORY key
e SCENE keys
RETURN
k
l
m
n
q
r
g
h
VOLUME
TUNING: Select the radio frequency.
HDMI 1-5: HDMI 1-5 jacks
AV 1-2: AV 1-2 jacks
d
BAND: Switches between FM and AM radio.
PRESET: Select a preset station.
c Input selection keys
V-AUX
j Radio keys
Select the assigned input source (included the selected radio
station or content when it is assigned), sound program, and
various settings with one touch. Also, turns on the unit when it is
in standby mode (p.56).
f PROGRAM keys
Select a sound program, a surround decoder, an input source, a
network source, a preset radio station, a browse screen page, the
volume of dialogue sounds or shuffle/repeat settings. (p.120)
g External device operation keys
Displays menus for the HDMI Control-compatible playback device
(p.145).
h ON SCREEN key
Registers FM/AM radio stations (p.64) and USB, Bluetooth, and
network content (p.85) as presets.
o HDMI OUT key
Enables/disables video/audio output from the HDMI OUT jack
(p.55).
p PARTY key
Turns on/off the party mode (p.84).
q VOLUME keys
Adjust the volume.
r MUTE key
Mutes the audio output.
s OPTION key
Displays the option menu (p.90).
Displays the on-screen menu on the TV.
i Menu operation keys
Displays status information on the TV (p.89).
Cursor keys: Select a menu or the parameter.
ENTER: Confirms a selected item.
RETURN: Returns to the previous screen.
En
t DISPLAY key
14
PREPARATIONS
General setup procedure
1 Connecting speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.16)
2 Connecting a TV and playback devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.28)
3 Connecting the FM/AM antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.34)
4 Connecting a network cable or preparing the wireless antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.35)
5 Connecting a device compatible with the trigger function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.36)
6 Connecting the power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.37)
7 Selecting an on-screen menu language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.38)
8 Configuring the necessary speaker settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.39)
9 Optimizing the speaker settings automatically (YPAO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.40)
10 Connecting to a network device wirelessly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.46)
11 Connecting to the MusicCast network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (p.54)
This completes all the preparations. Enjoy playing movies, music, radio and other content with the unit!
En
15
1 Connecting speakers
The unit has 7 built-in amplifiers. You can connect 2 to 9 speakers and up to 2 subwoofers to create the favorite acoustic space in your room.
You can also apply bi-amp connections or multi-zone configurations to enhance your system (p.23).
Caution
• Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 Ω MIN”. In this case, you can also use 4-ohm speakers as the front speakers.
For details, see “Setting the speaker impedance” (p.20).
Ideal speaker layout
Functions of each speaker
E
0.5 to 1 m
(1.6 to 3.3 ft)
1.8 m
(5.9 ft)
0.5 to 1 m
(1.6 to 3.3 ft)
1
9
1.8 m
(5.9 ft)
2
3
Speaker type
R
9
Function
Front (L/R)
12
Produce front left/right channel sounds (stereo sounds).
Center
3
Produces center channel sounds (such as movie dialogues and vocals).
Surround (L/R)
45
Produce surround left/right channel sounds. Surround speakers also
produce surround back channel sounds when no surround back
speakers are connected.
Surround back (L/R)
67
Produce surround back left/right channel sounds.
Front presence (L/R)
ER
Produce CINEMA DSP effect sounds or heights channel sounds of Dolby
Atmos and DTS:X contents.
Subwoofer
9
Produces LFE (low-frequency effect) channel sounds and reinforces
bass parts of other channels.
This channel is counted as “0.1”. You can connect 2 subwoofers to the
unit and place them on the left/right (or front/rear) sides of the room.
X
4
• We recommend using front presence speakers to have a full effect of the 3-dimensional sound fields. However,
5
10°~30°
the unit creates Virtual Presence Speaker (VPS) using the front, center and surround speakers to produce
3-dimensional sound fields even when no front presence speakers are connected (p.58).
10°~30°
• Use “Ideal speaker layout” (diagram on the left) as reference. You do not need to exactly adjust the speaker
6
layout to this diagram since the YPAO function of the unit will automatically optimize the speaker settings (such
7
as distances) to suit the speaker layout.
• When using only one surround back speaker, place it straight behind the listening position (middle of “SBL”
and “SBR” in the diagram).
0.3 m (1 ft) or more
En
16
Basic speaker configuration
If you do not apply bi-amp connections or multi-zone configurations, follow the procedure below to place the speakers in your room and connect them to the unit.
⬛ Placing speakers in your room
5.1.2 system [★] (using front presence speakers)
Depending on the number of speakers, place the speakers and subwoofer in your room. This
This speaker system uses the front presence speakers to produce a natural 3-dimensional
section describes the representative speaker layout examples.
sound field, and also creates Virtual Surround Back Speaker (VSBS) using the surround
X
speakers to add a sense of depth to the rear sound field. This system is suited for enjoying not
only 5.1-channel but also for 7.1-channel contents.
• To have a full effect of Dolby Atmos contents, we recommend using a speaker system with a ★ mark. However,
you can also play back Dolby Atmos contents with the 7.1 system (using surround back speakers).
E
• To have a full effect of DTS:X contents, we recommend using a speaker system with a ★ mark.
R
1
• (About the number of channels) For example, “5.1.2” denotes “standard 5.1-channel plus 2 for overhead
2
speaker channels”. For details on how to place overhead speakers (presence speakers), see “Presence speaker
9
layout” (p.19).
7.1/5.1.2 system [★]
4
3
5
(using both surround back and front presence speakers)
This speaker system brings out the full performance of the unit and allows you to enjoy a
highly-natural 3-dimensional sound field with any contents.
X
When using front presence speakers installed to the ceiling or when using the Dolby Enabled speakers as the
presence speakers, configure the “Layout (Front Presence)” setting in the “Setup” menu before performing YPAO
(p.39).
X
• The surround back speakers and presence speakers do not produce sounds simultaneously. The unit
automatically changes the speakers to be used, depending on the input signal and CINEMA DSP (p.58).
• When using front presence speakers installed to the ceiling or when using the Dolby Enabled speakers as the
presence speakers, configure the “Layout (Front Presence)” setting in the “Setup” menu before performing
YPAO (p.39).
En
17
7.1 system (using surround back speakers)
5.1 system (front 5.1-channel) (using surround speakers)
This speaker system creates Virtual Presence Speaker (VPS) using the front, center and
We recommend using this speaker system when you cannot place speakers in the rear side of
surround speakers to produce a 3-dimensional sound field, and also allows you to enjoy
the room.
extended surround sounds using the surround back speakers.
1
1
2
9
9
2
4
5
3
3
4
5
6
7
X
When placing surround speakers in the front side, set “Layout (Surround)” in the “Setup” menu to “Front” before
performing YPAO (p.39).
5.1 system
5.1 system (front 5.1-channel) (using front presence speakers)
1
We recommend using this speaker system when you cannot place speakers in the rear side of
2
the room.
9
3
E
4
R
1
5
9
2
3
X
You can enjoy surround sound even without the center speaker (4.1 system).
X
When using front presence speakers installed to the ceiling or when using the Dolby Enabled speakers as the
presence speakers, configure the “Layout (Front Presence)” setting in the “Setup” menu before performing YPAO
(p.39).
En
18
2.1 system
Overhead
Install the presence speakers to the ceiling above the listening position.
It delivers realistic overhead sound effects and sound field with excellent linkage of front and
1
2
rear sound spaces effectively.
9
Y
X
For details on the installation position of ceiling speakers, see “Notes on installation of ceiling speakers” (p.20).
Add the center speaker to configure a 3.1 system.
Dolby Enabled SP
Use the Dolby Enabled speakers as the presence speakers.
Presence speaker layout
This utilizes sounds reflected from ceiling and lets you enjoy overhead sounds only from
The unit provides three layout patterns for presence speakers (Front Height, Overhead and
speakers that are placed at the same level as traditional speakers.
Dolby Enabled SP). Choose a layout pattern that suits your listening environment.
X
You can enjoy Dolby Atmos, DTS:X or Cinema DSP 3D with any layout pattern.
Front Height
Install the presence speakers on the front wall.
It delivers a natural sound field with excellent linkage of left, right, top and bottom sound
spaces, and sound extensity effectively.
X
Place the Dolby Enabled speakers on top of or near the traditional front speakers. A Dolby Enabled speaker unit
may be integrated into a traditional speaker. For details, refer to the instruction manual of the Dolby Enabled
speakers.
En
19
Notes on installation of ceiling speakers
⬛ Setting the speaker impedance
When installing presence speakers to a ceiling, install them just above the listening position,
Under its default settings, the unit is configured for 8-ohm speakers. When using a 6-ohm
or the ceiling between the extensions of the front speakers and listening position.
speaker for any channel, set the speaker impedance to “6 Ω MIN”. In this case, you can also use
4-ohm speakers as the front speakers.
1
2
Before connecting speakers, connect the power cable to an AC wall outlet.
While holding down STRAIGHT on the front panel, press MAIN ZONE z.
MAIN ZONE z
Caution
STRAIGHT
• Be sure to use speakers that are made for ceiling use and take anti-drop measures. Ask a qualified
contractor or dealer personnel for installation works.
3
Check that “SP IMP.” is displayed on the front display.
LINK MASTER
OUT
ECO
2
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
SP IMP.••8¬MIN
4
5
Press MAIN ZONE z to set the unit to standby mode and remove the power
You are now ready to connect the speakers.
20
FPR
FPL
SW
SR
SL
SBL SB SBR
Press STRAIGHT to select “6 Ω MIN”.
cable from the AC wall outlet.
En
VOL. MUTE VIRTUAL
⬛ Connecting speakers
Speakers to be connected
Connect the speakers placed in your room to the unit.
Speaker system
(the number of channels)
Speaker type
Precaution for connecting of the speaker cables
Prepare speaker cables in a place away from the unit, to avoid accidentally dropping wire
strands into the unit's interior which could result in a short circuit or malfunction of the unit.
Improper connecting of the speaker cables may cause short circuit and also damage the unit
or the speakers.
• Remove the unit’s power cable from an AC wall outlet and turn off the subwoofer before
connecting the speakers.
7.1/5.1.2
5.1
2.1
Front (L/R) 12
⚫
⚫
⚫
Center 3
⚫
⚫
Surround (L/R) 45
⚫
⚪*3
Surround back (L/R) 67
⚪*1
Front presence (L/R) ER
⚪*2
⚪*4
⚫
⚫
Subwoofer 9
• Twist the bare wires of the speaker cables firmly together.
⚫
If you have nine speakers, you can use the both surround back speakers and front presence
speakers. In this case, the unit automatically changes the speakers to be used, depending on
the input signal and CINEMA DSP.
If you have seven speakers, use two of them as surround back speakers (*1) or front presence
speakers (*2).
If you have five speakers, use two of them as surround speakers (*3) or front presence speakers
• Do not let the bare wires of the speaker cable touch one another.
(*4).
X
• You can also connect up to 2 subwoofers (with built-in amplifier) to the unit.
• When apply this speaker configuration, set “Power Amp Assign” (p.107) to “Basic” (default).
Cables required for connection (commercially available)
• Do not let the bare wires of the speaker cable come into contact with the unit’s metal parts
Speaker cables (the number of speakers)
(rear panel and screws).
+
–
+
–
Audio pin cable (two for connecting two subwoofers)
If “Check SP Wires” appear on the front display when the unit is turned on, turn off the unit, and
then check the speaker cables short circuit.
En
21
Connecting speaker cables
Connection diagram
Refer to the following diagram and connect the speakers to the unit.
Speaker cables have two wires. One is for connecting the negative (-) terminals of the unit and
the speaker to each other, and the other is for the positive (+) terminals. If the wires are colored
The unit (rear)
SURROUND
to prevent confusion, connect the black wire to the negative and the other wire to the positive
CENTER
FRONT
terminal.
EXTRA SP1
F.PRESENCE
/ ZONE2
EXTRA SP2
SURROUND BACK
/ ZONE2 / BI-AMP
SINGLE
1
PRE OUT
SUBWOOFER
1
Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable and twist
the bare wires of the cable firmly together.
2
2
3
Loosen the speaker terminal.
Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the
terminal.
4
E
R
1
Tighten the terminal.
+ (red)
2
3
FR
ON
T
2
4
9
3
9
1
- (black)
Using a banana plug
4
(U.S.A., Canada, Brazil and General models only)
5
6
1
2
7
Tighten the speaker terminal.
Insert a banana plug into the end of the terminal.
1
Banana plug
FR
ON
T
2
Y
When using only one surround back speaker, connect it to the SINGLE jack (L side).
Connecting the subwoofer
Use an audio pin cable to connect the subwoofer.
Audio pin cable
En
22
Advanced speaker configuration
In addition to the basic speaker configuration (p.17), the unit also allows you to apply the following speaker configurations to enhance your system.
Using the four internal
amplifiers for front speakers to
have more high-quality sounds
Using the excess internal
amplifiers for stereo speakers
in another room
Bi-amp connection
Multi-zone configuration
(Example)
(Example)
Bi-amp
connection
Zone2
Main zone
En
23
⬛ Available speaker configurations
7.1 +1Zone
Main zone
Output
channel (max)
Bi-amp
7
7
5
⚪
Surround
back/ Front
presence
Multi-zone
Power Amp Assign
(p.107)
Page
Surround back
+1 (Zone2)
7.1 +1Zone
24
Front presence
+1 (Zone2)
5.1.2 +1Zone
25
5.1 BI-Amp
25
1
9
Y
2
1
2
9
3
4
5
When applying one of these configurations, you need to configure the “Power Amp Assign” setting in the “Setup”
menu (p.39).
6
7
Zone2
Main zone
Speaker
Connect to
12
FRONT
3
CENTER
45
SURROUND
67
EXTRA SP2
ER
(not used)
9
SUBWOOFER 1-2
Zone2 speakers
EXTRA SP1
X
When Zone2 output is enabled (p.83), the surround back speakers in the main zone do not output sound.
En
24
5.1.2 +1Zone
5.1 BI-Amp
Bi-amp
E
R
1
9
2
3
1
2
1
9
4
9
5
2
3
9
4
5
Zone2
Main zone
Speaker
Connect to
Speaker
Connect to
12
FRONT
12
FRONT and EXTRA SP2 (bi-amp connection)
3
CENTER
3
CENTER
45
SURROUND
45
SURROUND
67
(not used)
67
(not used)
ER
EXTRA SP1
ER
(not used)
9
SUBWOOFER 1-2
9
SUBWOOFER 1-2
Zone2 speakers
EXTRA SP2
X
When Zone2 output is enabled (p.83), the front presence speakers in the main zone do not output sound.
En
25
⬛ Connecting front speakers that support bi-amp
connections
Caution
and EXTRA SP2 jacks.
• Before making bi-amp connections, remove any brackets or cables that connect a woofer with a
tweeter. Refer to the instruction manual of the speakers for details. If you are not making bi-amp
connections, make sure that the brackets or cables are connected before connecting the speaker
cables.
To enable the bi-amp function, configure the “Power Amp Assign” setting in the “Setup” menu
• Surround back speakers cannot be used during bi-amp connections.
When using front speakers that support bi-amp connections, connect them to the FRONT jacks
after connecting the power cable to an AC wall outlet (p.39).
⬛ Connecting Zone2 speakers
The unit (rear)
When using Zone2 speakers, connect them to the EXTRA SP1 or EXTRA SP2 terminals.
SURROUND
CENTER
FRONT
EXTRA SP2
SURROUND BACK
/ ZONE2 / BI-AMP
SINGLE
EXTRA SP1
F.PRESENCE
/ ZONE2
To utilize the EXTRA SP terminals for Zone2 speakers, configure the “Power Amp Assign”
setting in the “Setup” menu after connecting the power cable to an AC wall outlet (p.39).
PRE OUT
SUBWOOFER
1
X
2
You can also connect Zone2 speakers using an external amplifier (p.81).
(when using surround back speakers in the main zone)
The unit (rear)
1
2
SURROUND
FRONT
CENTER
EXTRA SP2
SURROUND BACK
/ ZONE2 / BI-AMP
SINGLE
EXTRA SP1
F.PRESENCE
/ ZONE2
3
9
4
5
1
9
2
FL
FR
3
4
5
6
7
Zone2
X
The FRONT jacks and EXTRA SP2 jacks output the same signals.
Main zone
En
26
(when using front presence speakers in the main zone)
The unit (rear)
SURROUND
FRONT
CENTER
EXTRA SP2
SURROUND BACK
/ ZONE2 / BI-AMP
SINGLE
E
R
1
9
EXTRA SP1
F.PRESENCE
/ ZONE2
2
FL
FR
3
4
5
Zone2
Main zone
En
27
2 Connecting a TV and playback devices
Connect a TV and playback devices (video and audio devices) to the unit.
For information on how to connect a USB storage device, see “Connecting a USB storage device” (p.69).
Input/output jacks and cables
The unit is equipped with the following input/output jacks. Prepare the cables that match the jacks on your devices.
⬛ Video/audio jacks
⬛ Video jacks
To input/output video and audio signals, use the following jacks.
To input/output only video signals, use the following jacks.
HDMI jacks
COMPONENT VIDEO jacks
Transmit digital video and digital sound through a single jack. Use an HDMI cable.
Transmit video signals separated into three components: luminance (Y), chrominance blue
(Pb), and chrominance red (Pr). Use a component video cable with three plugs.
HDCP2.2
HDMI cable
(BD/DVD)
Y
Use a 19-pin HDMI cable with the HDMI logo. We recommend using a cable less than 5.0 m (16.4 ft) long to prevent
Component video cable
signal quality degradation.
X
VIDEO jacks
• The unit’s HDMI jacks support the HDMI Control, Audio Return Channel (ARC), and 3D and 4K Ultra HD video
Transmit analog video signals. Use a video pin cable.
transmission features.
AV 2
• Use a Premium High Speed HDMI Cable or Premium High Speed Cable with Ethernet to enjoy 3D or 4K Ultra HD
videos.
Video pin cable
En
28
⬛ Audio jacks
Connecting a TV
To input/output only audio signals, use the following jacks.
Connect the TV to the unit with an HDMI cable and a digital optical cable.
OPTICAL jacks
HDMI OUT jack
The unit (rear)
Transmit digital audio signals. Use a digital optical cable. Remove the tip protector (if
available) before using the cable.
HDMI input
HDMI OUT
TRIGGER OUT
12V 0.1A
(HDCP2.2)
HDMI
HDMI (HDCP2.
1
HDMI OUT
(HDCP2.2)
IN
1
OUT
2
ARC
(1 BD/DVD)
ARC
HDMI
HDMI
REMOTE
ANTENNA
(4 RADIO)
AUDIO 1
(2 TV)
Digital optical cable
FM
OPTICAL
AM
AUDIO 2
OPTICAL
OPTICAL
AUDIO 3
COAXIAL
AV 1
Y
OPTICAL
COAXIAL
VIDEO
O
OPTICAL
PR
PB
ZONE OUT
AUDIO 4
PHONO
AUDIO 1 jack
AV 2
AUDIOCOMPONENT
1
VIDEO
(2 TV)
AUDIO 5
ZONE 2
GND
COAXIAL jacks
O
TV
Transmit digital audio signals. Use a digital coaxial cable.
Audio output
(digital optical)
Digital coaxial cable
X
COAXIAL
• You do not make a digital optical cable connection between the TV and the unit in the following cases:
– If your TV supports Audio Return Channel (ARC)
– If you will receive TV broadcasts only from the set-top box
AUDIO jacks
• If you connect a TV that supports HDMI Control to the unit with an HDMI cable, you can control the unit’s power
and volume with the TV’s remote control.
(Stereo L/R jacks)
To use HDMI Control and ARC, you need to configure the HDMI settings on the unit. For details
Transmit analog stereo audio signals. Use a stereo pin cable (RCA cable).
on the settings, see “Information on HDMI” (p.145).
Stereo pin cable
About Audio Return Channel (ARC)
• ARC allows audio signals to travel both ways. If you connect a TV that supports ARC to the unit with a
single HDMI cable, you can output video/audio to the TV or input TV audio to the unit.
• When using ARC, connect a TV with an HDMI cable that supports ARC.
(Stereo mini jack)
Transmits analog stereo audio signals. Use a stereo mini-plug cable.
Stereo mini-plug cable
AUDIO
En
29
⬛ Component video connection
Connecting video devices (such as BD/DVD players)
Connect a video device to the unit with a component video cable and an audio cable (digital
Connect video devices such as BD/DVD players, set-top boxes (STBs) and game consoles to the
coaxial).
unit. Depending on the video/audio output jacks available on your video device, choose one of
the following connections. We recommend using an HDMI connection if the video device has
Output jacks on video device
Input jacks on the unit
an HDMI output jack.
X
Video
Audio
Component video
Digital coaxial
AV 1 (COMPONENT VIDEO + COAXIAL)
If the combination of video/audio input jacks available on the unit does not match your video device, change its
The unit (rear)
combination according to the output jacks of your device (p.30).
Audio output
(digital coaxial)
TRIGGER OUT
12V 0.1A
⬛ HDMI connection
AV 1 (COAXIAL) jack
HDMI (HDCP2
HDMI OUT
(HDCP2.2)
IN
1
OUT
2
(1 BD/DVD)
ARC
C
REMOTE
Connect a video device to the unit with an HDMI cable.
COAXIAL
ANTENNA
(4 RADIO)
AUDIO 1
(2 TV)
FM
OPTICAL
AM
COMPONENT
VIDEO
C
AUDIO 2
COAXIAL
OPTICAL
AUDIO 3
HDMI 1-5 jacks
The unit (rear)
AV 1
PR
HDMI (HDCP2.2)
HDMI
COAXIAL
Y
HDMI (HDCP2.2)
1
2
1
(1 BD/DVD)
HDMI
3
4
2
3
4
ZONE OUT
AUDIO 4
AUDIO 5
GND
5
5
Y
(1 BD/DVD)
ARC
Video device
PR
PB
PHONO
HDMI OUT
(HDCP2.2)
AV 2
VIDEO
COMPONENT VIDEO
COAXIAL
PB
ZONE 2
PR
PR
PB
PB
Y
Y
PR
ANTENNA
(4 RADIO)
FM
PB
Y
AM
HDMI
SPEAKERS
1
HDMI output
AV 2
NT VIDEO
VIDEO
SURROUND
CENTER
FRONT
AV 1 (COMPONENT VIDEO) jack
PR
ZONE OUT
O4
AUDIO 5
ZONE 2
PRE OUT
SUBWOOFER
1
2
HDMI
Video output
(component video)
If you select the input source by pressing AV 1, the video/audio played back on the video device
HDMI
will be output from the unit.
Video device
X
If you select the input source by pressing HDMI 1-5, the video/audio played back on the video
• This unit supports only the video signals of 481i and 576i (resolution).
device will be output from the unit.
• If you want to use an analog audio cable or a digital optical cable, refer to “Changing the combination of
Y
video/audio input jacks” (p.31).
If your video device supports HDCP 2.2, connect the device to the HDMI 1-3 jacks.
En
30
⬛ Composite video connection
⬛ Changing the combination of video/audio input jacks
Connect a video device to the unit with a video pin cable and an audio cable (digital coaxial,
If the combination of video/audio input jacks available on the unit does not match your video
digital optical, or stereo pin cable). Choose a set of input jacks (on the unit) depending on the
device, change its combination according to the output jacks of your device. You can connect
audio output jacks available on your video device.
a video device that has the following video/audio output jacks.
Output jacks on video device
Output jacks on video device
Input jacks on the unit
Input jacks on the unit
Video
Audio
Composite video
Analog stereo
Video
AV 2 (VIDEO + AUDIO)
Audio
Video
AUDIO 1 (OPTICAL)
Digital optical
AUDIO 2 (OPTICAL)
The unit (rear)
HDMI
TRIGGER OUT
12V 0.1A
Video output
(composite video)
HDMI OUT
(HDCP2.2)
IN
AV 2 (VIDEO) jack
1
OUT
(1 BD/DVD)
ARC
VIDEO
ANTENNA
(4 RADIO)
FM
OPTICAL
HDMI 1-5
AUDIO 4-5
VIDEO
AM
AV 1 (COAXIAL)
AUDIO 3 (COAXIAL)
AV 2 (AUDIO)
Analog stereo
REMOTE
AUDIO 1
(2 TV)
Digital coaxial
Audio
AUDIO 2
OPTICAL
V
AUDIO 3
COAXIAL
AV 1
Y
VIDEO
Video device
L
PR
PB
AUDIO 5
Z
L
L
L
GND
Analog stereo
R
R
R
AV 2 (AUDIO) jack
AV1
(COMPONENT VIDEO)
Component video
Z
AUDIO 4
PHONO
AUDIO 1 (OPTICAL)
Digital optical
AV 2
COMPONENT VIDEO
COAXIAL
V
AUDIO 2 (OPTICAL)
AV 2 (AUDIO)
AUDIO 4-5 (AUDIO)
R
AUDIO 1 (OPTICAL)
Digital optical
Audio output
(analog stereo)
AV2
(COMTPOSITE VIDEO)
Composite video
Digital coaxial
If you select the input source by pressing AV 2, the video/audio played back on the video device
will be output from the unit.
X
If you want to use a digital coaxial cable or a digital optical cable, refer to “Changing the combination of
video/audio input jacks” (p.31).
En
31
AUDIO 2 (OPTICAL)
AV 1 (COAXIAL)
AUDIO 3 (COAXIAL)
Necessary setting
5
For example, if you have connected a video device to AV 1 (COMPONENT VIDEO) and AV 2
Use the Cursor keys (e/r) to select “AV 1” (video input jack to be used) and
press the Cursor key (q).
(AUDIO) jacks of the unit, change the combination setting as follows.
Video output
(component video)
COMPONENT
VIDEO
The unit (rear)
PR
TRIGGER OUT
12V 0.1A
HDM
HDMI OUT
(HDCP2.2)
IN
1
OUT
2
(1 BD/DVD)
ARC
AV 1 (COMPONENT VIDEO)
jacks
PR
ANTENNA
(4 RADIO)
AUDIO 1
(2 TV)
FM
OPTICAL
PR
AM
Y
PB
AUDIO 2
Y
PR
PB
OPTICAL
AUDIO 3
AV 1
COAXIAL
Y
VIDEO
PR
PB
AUDIO
ZONE O
AUDIO 4
PHONO
Y
Y
AV 2
COMPONENT VIDEO
COAXIAL
PB
PB
REMOTE
AUDIO 5
ZONE
L
GND
L
L
R
R
Video device
6
7
Use the Cursor keys to select “Audio In” and press ENTER.
8
Press ON SCREEN.
Use the Cursor keys to select “AV 2” (audio input jack to be used).
R
AV 2 (AUDIO) jacks
Audio output
(analog stereo)
Y
The following operation is available only when your TV is connected to the unit via HDMI.
1
After connecting external devices (such as a TV and playback devices) and
power cable of the unit, turn on the unit.
2
Press AV 1 to select “AV 1” (video input jack to be used) as the input source.
1
2
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
This completes the necessary settings.
If you select “AV 1” as the input source by pressing AV 1, the video/audio played back on the
AV
MAIN
ZONE 2
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
ENTER
RETURN
3
4
video device will be output from the unit.
AV 1
DISPLAY
ON SCREEN
Cursor keys
ENTER
Press ON SCREEN.
Use the Cursor keys to select “Input” and press ENTER.
En
32
Connecting audio devices (such as CD players)
Connecting to the jacks on the front panel
Connect audio devices such as CD players, MD players, and a turntable to the unit. Depending
Use the VIDEO AUX jack to temporarily connect a playback device to the unit.
on the audio output jacks available on your audio device, choose one of the following
Before making a connection, stop playback on the device and turn down the volume on the
connections.
unit.
Audio output jacks on audio device
Audio input jacks on the unit
Digital optical
AUDIO 1-2 (OPTICAL)
Connect an HDMI-compatible device (such as game consoles and camcorders) to the unit with
an HDMI cable.
Connect a portable audio player to the unit with a stereo mini-cable.
AV 1 (COAXIAL)
Digital coaxial
AUDIO 3 (COAXIAL)
VOLUME
SCENE
AV 2 (AUDIO)
Analog stereo
1
2
3
4
AUDIO 4-5
INPUT
Turntable (PHONO)
TONE CONTROL
PROGRAM
(CONNECT)
The unit
(rear)
Audio output
(either digital optical,
digital coaxial, or analog stereo)
AV 1-2 jacks
AUDIO 1-5 jacks
TRIGGER OUT
12V 0.1A
2
3
AUDIO
The unit (front)
O
1
HDMI IN
HDMI
HDMI (HDCP2.2)
HDMI OUT
(HDCP2.2)
IN
OUT
VIDEO AUX
STRAIGHT
PHONO
OPTICAL
4
(1 BD/DVD)
ARC
C
REMOTE
ANTENNA
(4 RADIO)
AUDIO 1
(2 TV)
FM
OPTICAL
AM
COAXIAL
O
Audio device
AUDIO 2
OPTICAL
L
OPTICAL
AUDIO 3
AV 1
AV 2
COAXIAL
COAXIAL
Y
C
R
PR
PB
ZONE OUT
AUDIO 4
PHONO
Game console
L
VIDEO
COMPONENT VIDEO
COAXIAL
ZONE 2
AUDIO 5
PRE OUT
SUBWOOFER
1
L
R
GND
Portable audio
player
2
R
PHONO
L
Camcorder
PHONO
L
L
R
GND
R
R
If you select “VIDEO AUX” as the input source by pressing V-AUX, the video/audio played back
GND
PHONO jacks
Ground lead
Turntable
on the device will be output from the unit.
Audio output (PHONO)
Y
If you select the input source by pressing AV 1-2, AUDIO or PHONO, the audio played back on
You need to prepare an HDMI cable or audio cable that match the output jacks on your device.
the audio device will be output from the unit.
When connecting a turntable
• The PHONO jack of the unit is compatible with an MM cartridge. To connect a turntable with a
low-output MC cartridge, use a boosting transformer.
• Connecting the turntable to the GND terminal of the unit may reduce noise in the signal.
En
33
3 Connecting the FM/AM antennas
Connect the supplied FM/AM antennas to the unit.
Fix the end of the FM antenna to a wall, and place the AM antenna on a flat surface.
FM antenna
AM antenna
The unit
(rear)
TRIGGER OUT
12V 0.1A
HDMI (HDCP2.2)
HDMI OUT
(HDCP2.2)
IN
HDMI
NETWORK
(3 NET)
1
OUT
2
3
4
5
(1 BD/DVD)
ARC
REMOTE
ANTENNA
(4 RADIO)
AUDIO 1
(2 TV)
FM
OPTICAL
AM
AUDIO 2
OPTICAL
SPEAKERS
AUDIO 3
AV 2
COMPONENT VIDEO
COAXIAL
COAXIAL
AV 1
Y
PB
VIDEO
SURROUND
CENTER
FRONT
EXTRA SP2
SURROUND BACK
/ ZONE2 / BI-AMP
SINGLE
PR
ZONE OUT
PRE OUT
Assembling and connecting the AM antenna
Hold down
Insert
Release
X
• Unwind only the length of cable needed from the AM antenna unit.
• The wires of the AM antenna have no polarity.
En
34
4 Connecting a network cable or preparing the wireless antenna
Connect the unit to a router (access point) with a network cable, or prepare the wireless
Y
antenna for establishing a wireless network connection.
• Some security software installed on your PC or the firewall settings of network devices (such as a router) may
block the access of the unit to the network devices or the Internet. In these cases, configure the security
You can enjoy Internet radio or music files stored on media servers, such as PCs and Network
software or firewall settings appropriately.
Attached Storage (NAS), on the unit.
• Each server must be connected to the same subnet as the unit.
• To use the service via the Internet, broadband connection is strongly recommended.
Connecting the network cable
Preparing the wireless antenna
Connect the unit to your router with a commercially-available STP network cable (CAT-5 or
higher straight cable).
If you want to establish a wireless network connection, stand the wireless antenna up straight.
Network Attached Storage
(NAS)
Internet
For information on how to connect the unit to a network device wirelessly, see “Connecting to
a network device wirelessly” (p.46).
WAN
LAN
Modem
PC
Network cable
The unit (rear)
Router
NETWORK
(3 NET)
Mobile device
Y
SPEAKERS
NTER
FRONT
EXTRA SP2
SURROUND BACK
EXTRA SP1
F.PRESENCE
Do not apply excessive force on the antenna. Doing so may damage it.
X
• If you want to use a wired (network cable) connection when a wireless connection has been made, set “Network
Connection” (p.115) in the “Setup” menu to “Wired”.
• If you are using a router that supports DHCP, you do not need to configure any network settings for the unit, as
the network parameters (such as the IP address) will be assigned automatically to it. You only need to configure
the network settings if your router does not support DHCP or if you want to configure the network parameters
manually (p.115).
• You can check whether the network parameters (such as IP address) are properly assigned to the unit in
“Network” (p.124) in the “Information” menu.
En
35
5 Connecting a device compatible with the trigger function
The trigger function can control an external device in conjunction with operating the unit (such
as powering on/off and input selection). If you have a Yamaha subwoofer that supports a
system connection or a device with a trigger input jack, you can use the trigger function by
connecting the external device to the TRIGGER OUT jack with a monaural mini-jack cable.
TRIGGER OUT jack
TRIGGER OUT
12V 0.1A
TRIGGER OUT
12V 0.1A
HDMI (H
HDMI OUT
(HDCP2.2)
IN
1
OUT
2
(1 BD/DVD)
ARC
REMOTE
System
connector
jack
ANTENNA
(4 RADIO)
AUDIO 1
(2 TV)
FM
OPTICAL
AM
AUDIO 2
OPTICAL
AUDIO 3
AV 2
COMPONENT VIDEO
COAXIAL
COAXIAL
AV 1
Y
VIDEO
PR
PB
ZONE OUT
AUDIO 4
PHONO
AUDIO 5
ZONE 2
GND
Yamaha subwoofer that
supports a system connection
The unit (rear)
X
You can configure the trigger function settings in “Trigger Output” (p.121) in the “Setup” menu.
En
36
6 Connecting the power cable
Before connecting the power cable (Taiwan, Brazil and General models only)
Set the switch position of VOLTAGE SELECTOR according to your local voltage. Voltages are
AC 110–120/220–240 V, 50/60 Hz.
Y
Make sure you set VOLTAGE SELECTOR of the unit BEFORE plugging the power cable into an AC wall outlet.
Improper setting of VOLTAGE SELECTOR may cause damage to the unit and create a potential fire hazard.
VOLTAGE SELECTOR
The unit (rear)
VOLTAGE SELECTOR
220V240V
110V120V
SP2
D BACK
BI-AMP
SINGLE
EXTRA SP1
F.PRESENCE
/ ZONE2
CLASS 2 WIRING
CÂBLAGE CLASSE 2
After all the connections are complete, plug in the power cable.
The unit (rear)
To an AC wall outlet
NETWORK
(3 NET)
SPEAKERS
RONT
EXTRA SP2
SURROUND BACK
/ ZONE2 / BI-AMP
SINGLE
EXTRA SP1
F.PRESENCE
/ ZONE2
CLASS 2 WIRING
CÂBLAGE CLASSE 2
En
37
7 Selecting an on-screen menu language
z
HDMI
1
2
3
1
2
V-AUX
AUDIO
2
5
1
3
4
2
TUNER
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
Japanese, French, German, Spanish, Russian, Italian and Chinese.
2
3
Press z (receiver power) to turn on the unit.
Turn on the TV and switch the TV input to display video
from the unit (HDMI OUT jack).
X
SCENE
1
4
When you turn on the unit for the first time, a message regarding the network
setup appears. You can switch the language on this message screen.
PROGRAM MUTE
TOP MENU
VOLUME
POP-UP/MENU
ON
SCREEN
ON SCREEN
OPTION
ENTER
RETURN
DISPLAY
Cursor keys
ENTER
RETURN
3
4
Press ON SCREEN.
5
Use the Cursor keys (e/r) to select “Language” and the
Use the Cursor keys to select “Setup” and press ENTER.
BAND
MODE
TUNING
7
To exit from the menu, press ON SCREEN.
4
5
1
Select the desired on-screen menu language from English (default),
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
4
Cursor keys (q/w) to select the desired language.
6
To confirm the setting, press ENTER.
En
38
X
The information on the front display is provided in English only.
8 Configuring the necessary speaker settings
z
HDMI
1
2
3
If you use any of the following speaker configurations, follow the
procedure below to configure the corresponding speaker settings
4
manually before performing YPAO.
5
V-AUX
• Using bi-amp connection (p.26) or Zone2 speakers (p.26)
AUDIO
1
2
3
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
• Using the surround speakers for front 5.1-channel system (Virtual
CINEMA FRONT) (p.18)
• Using the presence speakers for Dolby Atmos or DTS:X playback (p.19)
SCENE
2
1
3
PROGRAM MUTE
TOP MENU
4
1
2
VOLUME
POP-UP/MENU
ON
SCREEN
X
Cursor keys
ENTER
RETURN
Turn on the TV and switch the TV input to display video
from the unit (HDMI OUT jack).
ON SCREEN
OPTION
ENTER
Press z (receiver power) to turn on the unit.
If you turn on the unit for the first time, the message regarding the network
setup appears. For now, press RETURN and proceed to Step 3.
DISPLAY
BAND
MODE
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
3
4
3
4
5
Press ON SCREEN.
Use the Cursor keys to select “Setup” and press ENTER.
Use the Cursor keys and ENTER to select “Speaker” and
then “Manual Setup”.
6
Configure the corresponding speaker settings.
• When using bi-amp connection or Zone2 speakers, select “Power
Amp Assign” (p.107), then select your speaker system.
• When using the surround speakers for front 5.1-channel system
(Virtual CINEMA FRONT), select “Configuration” ➞ “Layout” ➞
“Surround” (p.108), then select “Front”.
• When using the presence speakers for Dolby Atmos or DTS:X
playback, select “Configuration” ➞ “Layout” ➞ “Front
Presence” (p.109), then select your front presence speaker
layout.
7
To exit from the menu, press ON SCREEN.
En
39
9 Optimizing the speaker settings automatically (YPAO)
z
HDMI
1
2
3
The Yamaha Parametric room Acoustic Optimizer (YPAO) function
detects speaker connections, measures the distances from them to your
4
5
4
Place the YPAO microphone at your listening position and
listening position(s), and then automatically optimizes the speaker
connect it to the YPAO MIC jack on the front panel.
settings, such as volume balance and acoustic parameters, to suit your
X
V-AUX
AUDIO
1
2
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
room.
AV
MAIN
ZONE 2
X
ears). We recommend the use of a tripod as a microphone stand. You can use the
The YPAO function of the unit adopts the YPAO-R.S.C. (Reflected Sound Control)
technology that enables to create natural sound fields like a room specifically designed
SCENE
2
1
Place the YPAO microphone at your listening position (same height as your
3
PROGRAM MUTE
4
for acoustic perfection.
tripod screws to stabilize the microphone.
YPAO MIC
jack
Y
VOLUME
The unit (front)
YPAO MIC
Note the following regarding YPAO measurement.
– Test tones are output at high volume and may surprise or frighten small children.
POP-UP/MENU
TOP MENU
ON
SCREEN
– Test tone volume cannot be adjusted.
OPTION
1
– Keep the room as quiet as possible.
ENTER
2
– Stay in a corner of the room behind the listening position so that you do not become
an obstacle between speakers and the YPAO microphone.
RETURN
DISPLAY
RETURN
9
– Do not connect headphones.
3
BAND
MODE
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
4
1
2
Press z (receiver power) to turn on the unit.
Turn on the TV and switch the TV input to display video
4
YPAO
5
microphone
from the unit (HDMI OUT jack).
X
Ear height
If you turn on the unit for the first time, the message regarding the network
setup appears. For now, press RETURN and proceed to Step 3.
3
Turn on the subwoofer and set the volume to half. If the
crossover frequency is adjustable, set it to maximum.
VOLUME
MIN
MAX
CROSSOVER/
HIGH CUT
MIN
9
MAX
En
40
Y
The following screen appears on the TV.
If any error message (such as E-1) or warning message (such as W-1) appears, see
“Error messages” (p.44) or “Warning messages” (p.45).
X
HDMI
1
2
3
4
To check the measurement results, select “Result”. For details, see “Checking
5
V-AUX
the measurement results” (p.43).
AUDIO
1
2
3
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
4
AV
MAIN
ZONE 2
6
ENTER.
X
SCENE
2
1
3
• To cancel the operation, disconnect the YPAO microphone before starting the
4
measurement.
PROGRAM MUTE
Use the Cursor keys to select “Save/Cancel” and press
7
To save the measurement results, use the cursor keys
(e/r) to select “SAVE” and press ENTER.
• To configure the power amplifier assignment setting, press RETURN and
VOLUME
select “Manual Setup” (p.107).
POP-UP/MENU
TOP MENU
ON
SCREEN
5
OPTION
ENTER
RETURN
DISPLAY
BAND
Cursor keys
ENTER
RETURN
To start the measurement, use the Cursor keys to select
“Measure” and press ENTER.
The measurement will start in 10 seconds. Press ENTER again to
start the measurement immediately.
MODE
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
X
To cancel the measurement temporarily, press RETURN.
MUSIC
ENHANCER PURE DIRECT
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
The adjusted speaker settings are applied.
The following screen appears on the TV when the measurement
X
finishes.
To finish the measurement without saving the result, select “CANCEL”.
En
41
8
Use the Cursor keys (e/r) to select “YES” or “NO” to
enable/disable YPAO Volume and press ENTER.
HDMI
1
2
3
4
5
V-AUX
AUDIO
1
2
5
1
3
4
2
TUNER
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
SCENE
2
1
3
4
X
PROGRAM MUTE
• If YPAO Volume is enabled, the high- and low-frequency levels are
VOLUME
automatically adjusted according to the volume so that you can enjoy natural
sounds even at low volume.
POP-UP/MENU
TOP MENU
ON
SCREEN
• You can also enable/disable YPAO Volume in “YPAO Volume” (p.91) in the
OPTION
“Option” menu.
Cursor keys
ENTER
ENTER
RETURN
DISPLAY
9
Disconnect the YPAO microphone from the unit.
BAND
This completes optimization of the speaker settings.
MODE
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
3
4
Caution
• The YPAO microphone is sensitive to heat, so should not be placed anywhere
where it could be exposed to direct sunlight or high temperatures (such as on
top of AV equipment).
En
42
HDMI
1
2
3
Reloading the previous YPAO adjustments
You can check the YPAO measurement results.
When the speaker settings you have configured manually are not
1
4
5
Checking the measurement results
V-AUX
“Result” and press ENTER.
AUDIO
1
2
4
2
TUNER
X
NET
PHONO
You can also select “Result” from “Auto Setup” (p.104) in the “Setup” menu,
PARTY
HDMI OUT
1
BLUETOOTH
MAIN
USB
ZONE 2
which displays the previous measurement results.
2
1
3
PROGRAM MUTE
4
ON
SCREEN
ENTER.
a
ON SCREEN
b
OPTION
ENTER
RETURN
DISPLAY
Cursor keys
ENTER
RETURN
a Measurement result items
BAND
MODE
TUNING
PRESET
3
b Measurement result details
SUR. DECODE STRAIGHT
MOVIE
Use the Cursor keys to select “Setup Reload” and press
VOLUME
POP-UP/MENU
TOP MENU
In the “Setup” menu, select “Speaker”, “Auto Setup”,
and then “Result” (p.103).
2
The following screen appears.
SCENE
reload the previous YPAO adjustments.
1
3
AV
5
suitable, follow the procedure below to discard the manual settings and
After the measurement, use the Cursor keys to select
MUSIC
ENHANCER PURE DIRECT
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
3
4
2
Use the Cursor keys to select an item.
Polarity of each speaker
Wiring
Reverse: The speaker cable may be connected with the
reverse polarity (+/-).
Size of each speaker (cross-over frequency of the
subwoofer)
Size
Large: The speaker can reproduce low-frequency signals
effectively.
Small: The speaker cannot reproduce low-frequency
signals effectively.
3
Distance
Distance from the listening position to each speaker
Level
Output level adjustment for each speaker
To finish checking the results and return to the previous
screen, press RETURN.
En
43
To exit from the menu, press ON SCREEN.
Error messages
If any error message is displayed during the measurement, resolve the problem and perform YPAO again.
Error message
Cause
Remedy
E-1: No Front SP
Front speakers are not detected.
E-2: No Sur. SP
One of the surround speakers cannot be detected.
E-3: No F.PRNS SP
One of the presence speakers cannot be detected.
E-4: SBR ➞ SBL
A surround back speaker is connected to the R side only.
When using only one surround back speaker, you need to connect it to the SINGLE jack (L side). Follow the on-screen
instructions to exit YPAO, turn off the unit, and then reconnect the speaker.
E-5: Noisy
The noise is too loud.
Keep the room quiet and follow the on-screen instructions to start the measurement again. If you select “PROCEED”,
YPAO takes the measurement again and ignores any noise detected.
E-6: Check Sur.
Surround back speakers are connected, but no surround speakers
are connected.
Surround speakers need to be connected in order to use surround back speakers. Follow the on-screen instructions
to exit YPAO, turn off the unit, and then reconnect the speakers.
E-7: No MIC
The YPAO microphone has been removed.
Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start the
measurement again.
E-8: No Signal
The YPAO microphone cannot detect test tones.
Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start the
measurement again. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center.
E-9: User Cancel
The measurement has been canceled.
Follow the on-screen instructions to start the measurement again. To cancel the measurement, select “EXIT”.
E-10: Internal Error
An internal error has occurred.
Follow the on-screen instructions to exit YPAO, turn off and on the unit. If this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or service center.
Follow the on-screen instructions to exit YPAO, turn off the unit, and then check the speaker connections.
En
44
Warning messages
If a warning message is displayed after the measurement, you can still save the measurement results by following on-screen instructions.
However, we recommend you perform YPAO again in order to use the unit with the optimal speaker settings.
Warning message
Cause
Remedy
Select “Wiring” in “Result” (p.43) and check the cable connections (+/-) of the speaker identified by “Reverse”.
If the speaker is connected incorrectly:
W-1: Out of Phase
A speaker cable may be connected with the reverse polarity (+/-).
Turn off the unit and then reconnect the speaker cable.
If the speaker is connected correctly:
Depending on the type of speakers or room environment, this message may appear even if the speakers are
connected correctly. In this case, you can ignore the message.
W-2: Over Distance
A speaker is placed more than 24 m (80 ft) from the listening
position.
Select “Distance” in “Result” (p.43) and move the speaker identified by “>24.00m (>80.0ft)” within 24 m (80 ft) of the
listening position.
W-3: Level Error
There are significant volume differences between the speakers.
Check the usage environment and cable connections (+/-) of each speaker, and the volume of the subwoofer. We
recommend using the same speakers or speakers with specifications that are as similar as possible.
En
45
10 Connecting to a network device wirelessly
⬛ Connecting without a wireless router (access point)
Connect the unit to a wireless router (access point) or a mobile device by establishing a
wireless connection.
Connect a mobile device to the unit directly.
You can use the application for smartphone / tablet “AV CONTROLLER” (p.7) to control the unit
Selecting the connection method
from mobiles devices or enjoy music files stored on mobiles devices on the unit.
Select a connection method according to your network environment.
⬛ Connecting with a wireless router (access point)
Connect the unit to a wireless router (access point).
You can enjoy Internet radio, AirPlay, or music files stored on media servers (PC/NAS) on the
Mobile device
(such as iPhone)
unit.
The unit
For details on connection, see “Connecting a mobile device to the unit directly (Wireless
Internet
Direct)” (p.52).
Wireless router
Y
• You cannot use Wireless Direct simultaneously with the wired (network cable) connection (p.35) or the wireless
network connection (p.47).
Modem
• When Wireless Direct is enabled, the following functions are not available.
– Internet radio
– Network services
– Playback of music stored on media servers (PC/NAS)
Mobile device
(such as iPhone)
The unit
For details on connection, see “Connecting the unit to a wireless network” (p.47).
Y
• You cannot use the wireless network connection simultaneously with the wired (network cable) connection
(p.35) or Wireless Direct (p.52).
• If the unit and the wireless router (access point) are too far apart, the unit may not connect to a wireless router
(access point). In such case, place them close to each other.
En
46
Connecting the unit to a wireless network
There are several methods to connect the unit to a wireless network.
z
HDMI
1
2
3
5
• Using MusicCast CONTROLLER (p.54)
V-AUX
AUDIO
1
2
5
1
Select a connection method according to your environment.
4
3
4
2
TUNER
• Sharing the iOS device setting (p.47)
4
5
6
BLUETOOTH
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
3
Use the Cursor keys (q/w) to select “Network
• Using the WPS push button configuration (p.48)
7
• Using other connection methods (p.49)
4
Use the Cursor keys (q/w) and ENTER to check “Wireless
(Wi-Fi)” and select “OK”.
⬛ Sharing the iOS device setting
SCENE
2
1
Use the Cursor keys (e/r) to select “Network”.
Connection” and press ENTER.
AV
MAIN
Use the Cursor keys to select “Setup” and press ENTER.
You can easily set up a wireless connection by applying the connection
PROGRAM MUTE
VOLUME
POP-UP/MENU
TOP MENU
ON
SCREEN
settings on iOS devices (iPhone/iPad/iPod touch).
ON SCREEN
wireless router.
OPTION
Cursor keys
ENTER
ENTER
RETURN
DISPLAY
Before proceeding, confirm that your iOS device is connected to a
Y
If you set up a wireless connection with this method, the following settings will be
initialized.
X
BAND
– Network settings
MODE
TUNING
The checkmark indicates the current setting.
PRESET
– Bluetooth settings
SUR. DECODE STRAIGHT
8
– USB and network items registered as shortcuts
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
– Account information for the network services
5
6
7
8
9
0
MEMORY
ENT
X
ENHANCER PURE DIRECT
– Internet radio stations registered to “Favorites”
Wi-Fi Settings (iOS)” and select “NEXT”.
• You need iOS device with iOS 7 or later. (The following procedure is a setup example
for iOS 10.)
• This configuration does not work if the security method of your wireless router
(access point) is WEP. In this case, use other connection method.
1
2
Press z (receiver power) to turn on the unit.
Turn on the TV and switch the TV input to display video
from the unit (HDMI OUT jack).
Y
Operations with TV screen are available only when your TV is connected to the
unit via HDMI.
3
Use the Cursor keys (q/w) and ENTER to check “Share
Press ON SCREEN.
En
47
9
After checking the on-screen message, use the Cursor
keys (e/r) and ENTER to select “NEXT”.
z
HDMI
1
2
3
You can easily set up a wireless connection with one push of the WPS
button.
Y
4
5
⬛ Using the WPS push button configuration
This configuration does not work if the security method of your wireless router (access
V-AUX
AUDIO
1
2
5
1
3
4
2
TUNER
point) is WEP. In this case, use other connection method.
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
1
2
SCENE
2
1
3
PROGRAM MUTE
4
10 On the iOS device, select the unit as the AirPlay speaker in
VOLUME
the Wi-Fi screen.
TOP MENU
OPTION
RETURN
connection method.
MODE
PRESET
SUR. DECODE STRAIGHT
MUSIC
INFO
SLEEP
1
2
3
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
4
Push the WPS button on the wireless router (access
If “Not connected” appears, repeat from Step 1 or try another
BAND
MOVIE
3
the front display.
DISPLAY
TUNING
“Press WPS button on Access Point” appears on the front display.
When the connection process finishes, “Completed” appears on
Cursor keys
ENTER
ENTER
Hold down INFO (WPS) on the front panel for 3 seconds.
point).
POP-UP/MENU
ON
SCREEN
Press z (receiver power) to turn on the unit.
The name of the unit
11 Check the network currently selected and tap “Next”.
Tap here to start setup
The network currently selected
When the sharing process finishes, the unit is automatically
connected to the selected network (access point).
En
48
⬛ Using other connection methods
If your wireless router (access point) does not support WPS push button
z
2
3
4
5
1
2
V-AUX
AUDIO
1
2
3
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
2
3
Press z (receiver power) to turn on the unit.
Turn on the TV and switch the TV input to display video
Y
4
Operations with TV screen are available only when your TV is connected to the
PROGRAM MUTE
POP-UP/MENU
TOP MENU
Cursor keys
ENTER
RETURN
DISPLAY
BAND
MODE
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
ON SCREEN
OPTION
ENTER
MUSIC
3
4
5
6
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
3
4
WPS Button
You can set up a wireless connection with the WPS
button while viewing the TV screen. Follow the
instructions displayed on the TV screen.
Use the Cursor keys to select “Setup” and press ENTER.
Share Wi-Fi
Settings (iOS)
See “Sharing the iOS device setting” (p.47).
Use the Cursor keys (e/r) to select “Network”.
Access Point Scan
You can set up a wireless connection by searching for
an access point. For details on settings, see
“Searching for an access point” (p.50).
Press ON SCREEN.
Use the Cursor keys (q/w) to select “Network
Connection” and press ENTER.
ENHANCER PURE DIRECT
INFO
The following connection methods are available.
unit via HDMI.
VOLUME
ON
SCREEN
desired connection method and select “NEXT”.
from the unit (HDMI OUT jack).
SCENE
1
Use the Cursor keys (q/w) and ENTER to select the
wireless network settings.
HDMI
1
configuration method, follow the procedure below to configure the
8
7
Manual Setting
Use the Cursor keys (q/w) and ENTER to check “Wireless
(Wi-Fi)” and select “OK”.
PIN Code
You can set up a wireless connection by entering the
required information (such as SSID)
manually. For details on settings, see “Setting up the
wireless connection manually” (p.50).
You can set up a wireless connection by entering the
unit’s PIN code into the wireless router (access
point). The method is available if the wireless router
(access point) supports the WPS PIN code method.
For details on settings, see “Using the PIN code”
(p.51).
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by the Wi-Fi Alliance,
which allows easy establishment of a wireless home network.
X
The checkmark indicates the current setting.
En
49
Searching for an access point
HDMI
1
2
3
4
5
V-AUX
2
3
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
If you select “Access Point Scan” as the connection method, the unit
If you select “Manual Setting” as the connection method, the wireless
starts searching for access points. After a while, the list of available
connection setting screen appears on the TV.
access points appears on the TV screen.
You need to setup the SSID (network name), encryption method and
1
AUDIO
1
4
AV
MAIN
ZONE 2
3
security key for your network.
Use the Cursor keys and ENTER to check the desired
1
access point and select “NEXT”.
2
4
Use the Cursor keys and ENTER to enter the SSID of the
access point and select “NEXT”.
The wireless connection setting screen appears on the TV.
SCENE
2
1
Setting up the wireless connection manually
Use the Cursor keys and ENTER to enter the security key
and select “NEXT”.
PROGRAM MUTE
VOLUME
POP-UP/MENU
TOP MENU
ON
SCREEN
ON SCREEN
OPTION
Cursor keys
ENTER
ENTER
RETURN
2
DISPLAY
TUNING
Use the Cursor keys (q/w) and ENTER to check the
security method of the access point and select “NEXT”.
BAND
MODE
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
3
Use the Cursor keys (e/r) to select “CONNECT” and
press ENTER to start the connection process.
When the connection process finishes, “Completed” appears on
the TV screen.
If “Not connected” appears, repeat from Step 1 or try another
connection method.
4
To exit from the menu, press ON SCREEN.
En
50
Settings
None, WEP, WPA2-PSK (AES), Mixed Mode
3
Use the Cursor keys and ENTER to enter the security key
If you select “PIN Code” as the connection method, the list of available
and select “NEXT”.
2
access points appears on the TV screen.
If you select “None” in Step 2, this setting is not available. Proceed
HDMI
1
3
4
5
to Step 4.
V-AUX
If you select “WEP”, enter either 5 or 13 character string, or 10 or 26
AUDIO
1
2
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
ZONE 2
2
3
Use the Cursor keys and ENTER to check the desired
access point and select “NEXT”.
The PIN code of the unit appears on the TV screen.
If you select other method, enter either 8 to 63 character string, or
2
64 hexadecimal digits.
SCENE
1
1
hexadecimal digits.
AV
MAIN
Using the PIN code
Enter the unit’s PIN code into the wireless router (access
point).
4
For details on settings, refer to the instruction manual of the
PROGRAM MUTE
POP-UP/MENU
TOP MENU
wireless router (access point).
VOLUME
ON
SCREEN
3
ON SCREEN
OPTION
press ENTER to start the connection process.
Cursor keys
ENTER
ENTER
RETURN
DISPLAY
BAND
MODE
TUNING
Use the Cursor keys (e/r) to select “CONNECT” and
When the connection process finishes, “Completed” appears on
4
the TV screen.
Use the Cursor keys (e/r) to select “CONNECT” and
If “Not connected” appears, repeat from Step 1 or try another
press ENTER to start the connection process.
PRESET
connection method.
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
When the connection process finishes, “Completed” appears on
ENHANCER PURE DIRECT
the TV screen.
3
4
If “Not connected” appears, check that all the information is
entered correctly, and repeat from Step 1.
5
To exit from the menu, press ON SCREEN.
En
51
4
To exit from the menu, press ON SCREEN.
Connecting a mobile device to the unit
directly (Wireless Direct)
z
HDMI
1
2
3
4
5
2
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
ZONE 2
Direct” and select “OK”.
Follow the procedure below to connect a mobile device to the unit
Y
AV
MAIN
Use the Cursor keys (q/w) and ENTER to check “Wireless
directly.
V-AUX
AUDIO
1
7
Wireless Direct connection may be insecure since the communication is not strongly
encrypted. The unit may operate by playback operation on wireless devices connected
to the unit without permission.
SCENE
2
1
3
PROGRAM MUTE
VOLUME
POP-UP/MENU
TOP MENU
1
2
4
ON
SCREEN
The checkmark indicates the current setting.
8
Y
Use the Cursor keys (q/w) and ENTER to check the
desired security method and select “NEXT”.
Operations with TV screen are available only when your TV is connected to the
Cursor keys
ENTER
RETURN
X
Turn on the TV and switch the TV input to display video
from the unit (HDMI OUT jack).
ON SCREEN
OPTION
ENTER
Press z (receiver power) to turn on the unit.
unit via HDMI.
DISPLAY
BAND
MODE
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
4
3
4
5
6
Press ON SCREEN.
Use the Cursor keys to select “Setup” and press ENTER.
Use the Cursor keys (e/r) to select “Network”.
Use the Cursor keys (q/w) to select “Network
Settings
None, WPA2-PSK (AES)
Connection” and press ENTER.
Y
If you select “None”, the connection may be insecure since the communication
is not encrypted.
En
52
9
HDMI
1
2
3
4
5
Use the Cursor keys and ENTER to enter the security key
and select “NEXT”.
For details on settings of your mobile device, refer to the
If you select “None” in Step 8, this setting is not available. Proceed
instruction manual of the mobile device.
to Step 10.
1
Enable the Wi-Fi function on the mobile device.
2
Select the SSID displayed in Step 10 from the list of available
V-AUX
Otherwise, enter either 8 to 63 character string, or 64 hexadecimal
AUDIO
1
2
5
1
3
4
2
TUNER
digits.
AV
BLUETOOTH
MAIN
access points.
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
3
SCENE
2
1
3
PROGRAM MUTE
POP-UP/MENU
TOP MENU
12 To exit from the menu, press ON SCREEN.
ON SCREEN
OPTION
Cursor keys
ENTER
ENTER
RETURN
DISPLAY
BAND
MODE
TUNING
10 Use the Cursor keys (e/r) to select “OK” and press
ENTER to save the setting.
The settings made appear on the TV screen.
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
5
6
7
8
9
0
MEMORY
ENT
When you are prompted for a password, enter the security key
displayed in Step 10.
4
VOLUME
ON
SCREEN
11 Configure the Wi-Fi settings of a mobile device.
ENHANCER PURE DIRECT
4
The SSID and security key information is required for setup of a
mobile device.
En
53
11 Connecting to the MusicCast network
z
HDMI
1
2
3
MusicCast is a brand new wireless musical solution from Yamaha,
allowing you to share music among all of your rooms with a variety of
4
devices. You can enjoy music from your smartphone, PC, NAS drive and
5
V-AUX
music streaming service anywhere in your house with one easy-to-use
AUDIO
1
2
5
1
3
4
2
TUNER
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
2
3
4
your mobile device and tap “Setup”.
X
http://www.yamaha.com/musiccast/
If you have already connected other MusicCast compatible devices to the
network, tap “Settings” and then “Add New Device”.
dedicated application “MusicCast CONTROLLER”.
VOLUME
3
POP-UP/MENU
TOP MENU
OPTION
Operate the “MusicCast CONTROLLER” application
following the on screen instructions, then hold down
CONNECT on the front panel of the unit for 5 seconds.
room and play them back simultaneously.
ON
SCREEN
Tap the “MusicCast CONTROLLER” application icon on
products, refer to the following site:
• Link a MusicCast compatible device to another device in a different
PROGRAM MUTE
Press z (receiver power) to turn on the unit.
application. For more details and a lineup of MusicCast compatible
• Seamlessly control all MusicCast compatible devices with the
SCENE
1
1
2
• Play back music from music streaming services. (The compatible music
streaming services may differ depending on your region and product.)
Y
ENTER
Access the Yamaha Downloads site (http://download.yamaha.com/) to download
RETURN
DISPLAY
MusicCast Setup Guide.
BAND
CONNECT
MODE
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
MusicCast CONTROLLER
4
ENHANCER PURE DIRECT
Operate the “MusicCast CONTROLLER” application
following the onscreen instructions to set up the network.
5
Operate the “MusicCast CONTROLLER” application to
playback.
To use the network features on the MusicCast compatible device, you
Y
need the dedicated application “MusicCast CONTROLLER” for the
• AirPlay and DSD audio cannot be delivered.
operation. Search for the free application “MusicCast CONTROLLER” on
• When the Pure Direct is enabled, input sources other than the network sources and
USB cannot be delivered.
the App Store or Google Play and install it to your device.
Adding the unit to the MusicCast network
• If you configure the unit’s wireless settings with this method, the signal strength
indicator of the front display lights up when the unit is connecting to a network (even
if a wired connection is used).
• You can interlock the power of MusicCast devices with the unit (MusicCast master).
For details, see “MusicCast Link Power Interlock” (p.116) in the “Setup” menu.
Follow the procedure below to add the unit to the MusicCast network.
You can also configure the unit’s wireless settings at once.
Y
The SSID and security key for your network will be needed.
En
54
PLAYBACK
HDMI
1
2
3
Basic playback procedure
4
5
V-AUX
AUDIO
1
2
5
1
3
4
2
TUNER
Input selection keys
1
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
On-screen input selection
Turn on the external devices (such as a TV or BD/DVD
a Press ON SCREEN.
player) connected to the unit.
b Use the Cursor keys to select “Input” and press ENTER.
HDMI OUT
SCENE
2
1
3
PROGRAM MUTE
4
VOLUME
MUTE
VOLUME
2
3
Use the Input selection keys to select an input source.
ENTER.
Start playback on the external device or select a radio
station.
POP-UP/MENU
TOP MENU
ON
SCREEN
ON SCREEN
c Use the Cursor keys to select the desired input source and press
Selecting an HDMI output jack
Refer to the instruction manual for the external device.
OPTION
For details on the following operations, see the corresponding
Cursor keys
ENTER
ENTER
RETURN
pages.
BAND
TUNING
signal output changes.
• Playing back music via Bluetooth (p.67)
MODE
Press HDMI OUT to select an HDMI OUT jack.
Each time you press the key, the HDMI OUT jack to be used for
• Listening to FM/AM radio (p.63)
DISPLAY
1
PRESET
LINK MASTER
• Playing back music stored on a USB storage device (p.69)
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
• Playing back music stored on media servers (PCs/NAS) (p.72)
ENHANCER PURE DIRECT
• Listening to Internet radio (p.76)
• Playing back iTunes/iPhone music with AirPlay (p.79)
4
Press VOLUME to adjust the volume.
X
• To mute the audio output, press MUTE. Press MUTE again to unmute.
• To adjust the treble/bass settings, use the “Option” menu or TONE CONTROL
on the front panel (p.91).
En
55
OUT
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
HDMI OUT On
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
HDMI OUT On
Output the signals at the HDMI OUT jack.
HDMI OUT Off
Does not output the signals at the HDMI OUT jacks.
Selecting the input source and favorite settings with one touch (SCENE)
The SCENE function allows you to select the assigned input source
1
2
3
4
sound program and Compressed Music Enhancer on/off with just one
5
V-AUX
touch.
AUDIO
1
2
5
1
Registering a scene
(including the selected radio station or content when it is assigned),
HDMI
3
4
2
TUNER
1
you want to assign to a scene.
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
1
Press SCENE.
2
station or content when it is assigned) (p.55)
scene are selected. The unit turns on automatically when it is in
3
PROGRAM MUTE
• Select the assigned input source (including the selected radio
The input source and settings registered to the corresponding
SCENE
1
4
VOLUME
Perform the following operations to prepare the settings
SCENE
• Select a sound program (p.57) or straight decode mode (p.61)
standby mode.
• Enable/disable Compressed Music Enhancer (p.62)
By default, the following settings are registered for each scene.
X
When the input source is NET, USB, Bluetooth or TUNER, the selected radio
TOP MENU
POP-UP/MENU
ON
SCREEN
SCENE
2
1
3
4
station or content is assigned.
OPTION
Input
HDMI 1
AUDIO1
NET RADIO
TUNER
MUSIC
MUSIC
(7ch Stereo)
(7ch Stereo)
On
On
ENTER
Sound program MOVIE (Sci-Fi) STRAIGHT
RETURN
DISPLAY
BAND
MODE
TUNING
PRESET
2
Hold down the desired SCENE key until “SET Complete”
appears on the front display.
LINK MASTER
Compressed
Off
Music Enhancer
On
OUT
ECO
2
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
SET Complete
SUR. DECODE STRAIGHT
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
• You can also configure scene assignments in the “Scene” menu (p.96).
5
6
7
8
• The SCENE link playback function allows you to start playback of an external device
9
0
MEMORY
ENT
connected to the unit via HDMI. To enable SCENE link playback, specify the device
X
ENHANCER PURE DIRECT
type in “Device Control” (p.97) in the “Scene” menu.
En
56
Selecting the sound mode
The unit is equipped with a variety of sound programs and surround
decoders that allow you to enjoy playback sources with your favorite
HDMI
1
2
3
4
sound mode (such as sound field effect or stereo playback).
5
AUDIO
2
5
1
3
4
2
TUNER
Selecting a sound program suitable for movies
AV
BLUETOOTH
MAIN
NET
PHONO
HDMI OUT
and press ENTER.
This mode lets you enjoy sound field effects optimized for viewing
video sources, such as movies, TV programs, and games (p.58).
SCENE
2
1
c Use the Cursor keys to select a sound program/surround decoder
• Press MOVIE repeatedly.
PARTY
USB
ZONE 2
3
a Press ON SCREEN.
b Use the Cursor keys to select “DSP Program” and press ENTER.
V-AUX
1
On-screen sound program/surround decoder selection
X
• You can also switch the sound programs and surround decoder by pressing
4
PROGRAM.
Selecting a sound program suitable for music or stereo playback
PROGRAM MUTE
VOLUME
POP-UP/MENU
TOP MENU
ON
SCREEN
PROGRAM
ON SCREEN
OPTION
• Press MUSIC repeatedly.
• You can change the settings of the surround programs and surround decoders in the
“DSP Program” menu (p.100).
This mode lets you enjoy sound field effects optimized for listening
• The sound mode can be applied separately to each input source.
music sources or stereo playback (p.59).
• You can check which speakers are currently outputting sound by looking at the
speaker indicators on the unit’s front panel (p.11) or at the “Audio Signal” screen in
Cursor keys
ENTER
ENTER
RETURN
• Press SUR. DECODE repeatedly.
DISPLAY
BAND
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
Precaution for enjoying Dolby Atmos®
This mode lets you enjoy unprocessed multichannel playback from
MODE
TUNING
the “Information” menu (p.123).
Selecting a surround decoder
MOVIE
MUSIC
SUR.DECODE
STRAIGHT
ENHANCER
PURE DIRECT
2-channel sources (p.61).
• Dolby Atmos contents are decoded as Dolby TrueHD or Dolby Digital Plus in
the following situations. (Dolby Atmos PCM format is always decoded as
Dolby Atmos.)
– Any of CINEMA DSP programs is selected.
Switching to the straight decode mode
– Neither surround back nor presence speakers are used.
• Press STRAIGHT.
– Headphones are used (2-channel playback).
This mode lets you enjoy unprocessed sounds in original channels
(p.61).
• When the Dolby Atmos decoder is working, virtual surround processing (such
as Virtual CINEMA FRONT) (p.58), YPAO Volume (p.91) or Compressed Music
Enhancer (p.62) does not work.
Switching to the Pure Direct
• Press PURE DIRECT.
Precaution for enjoying DTS:X™
This mode lets you enjoy pure high fidelity sound by reducing the
electrical noise from other circuitry (p.62).
• DTS:X contents are decoded as DTS-HD format when any of CINEMA DSP
programs is selected.
• When the DTS:X decoder is working, virtual surround processing (such as
Virtual CINEMA FRONT) (p.58), YPAO Volume (p.91), Dialogue Level (p.91),
Extra Bass (p.92) or Compressed Music Enhancer (p.62) does not work.
Enabling Compressed Music Enhancer
• Press ENHANCER.
This mode lets you enjoy compressed music with additional depth and
breadth (p.62).
En
57
• When DTS:X contents are played back, you can adjust the volume of dialogue
sounds in “DTS Dialogue Control” (p.91) in the “Option” menu.
⬛ Sound programs suitable for movies (MOVIE)
Enjoying stereoscopic sound fields (CINEMA DSP 3D)
The following sound programs are optimized for viewing video sources, such as movies, TV
programs, and games.
The unit is equipped with a variety of sound programs that utilize Yamaha’s original DSP
MOVIE THEATER
technology (CINEMA DSP 3D). It allows you to easily create sound fields like actual movie
theaters or concert halls in your room and enjoy natural stereoscopic sound fields.
Sound program category
Standard
This program creates a sound field that emphasizes the surround feeling without
disturbing the original acoustic positioning of multichannel audio, such as Dolby
Digital and DTS. Its design is based on the concept of the ideal movie theater, in
which the audience is surrounded by beautiful reverberations from the left, right,
and rear.
Spectacle
This program delivers the scale and grandeur of spectacular movie productions.
It delivers an expansive sound space to match the cinemascope wide-screen, and
boasts a broad dynamic range, providing everything from small delicate sounds
to powerful loud booms.
Sci-Fi
This program clearly reproduces the finely elaborated sound design of the latest
Sci-Fi and SFX movies. You can enjoy a variety of cinematographically created
virtual spaces reproduced with clear separation between dialogue, sound effects,
and background music.
Adventure
This program is ideal for reproducing the sound design of action and adventure
movies precisely. The sound field restrains reverberations, but puts emphasis on
reproducing a sensation of expansiveness on both sides, powerful space
expanded widely to the left and right. The restrained depth creates a clear and
powerful space, while also maintaining the articulation of the sounds and the
separation of the channels.
Drama
This program features stable reverberations that match a wide range of movie
genres, from serious dramas to musicals and comedies. The reverberations are
modest, but suitably stereophonic. The sound effects and background music are
reproduced with a gentle echo that does not impinge on the articulation of the
dialogue. You’ll never get tired listening for long periods.
Mono Movie
This program reproduces monaural video sources, such as classic movies, in an
atmosphere of a good old movie theater. The program creates a pleasant space
with depth, by adding breadth and the appropriate reverberation to the original
audio.
“CINEMA DSP” lights up
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
OUT
2
ECO
Sci-Fi
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
Sound program
X
• To use the conventional CINEMA DSP, set “CINEMA DSP 3D Mode” (p.111) in the “Setup” menu to “Off”.
• We recommend using presence speakers in order to experience the full effect of the stereoscopic sound fields.
However, even when no presence speakers are connected, the unit creates Virtual Presence Speaker (VPS)
using the front, center, and surround speakers to produce stereoscopic sound fields.
• If a multichannel source (6.1 channels or more) is input when no surround back speakers are connected, the
unit creates Virtual Surround Back Speaker (VSBS) using the surround speakers to add a sense of depth to the
rear sound field.
• When VPS or VSBS is working, “VIRTUAL” lights up in the front display.
En
58
⬛ Sound programs suitable for music/stereo playback
(MUSIC)
ENTERTAINMENT
Sports
This program allows listeners to enjoy the rich vividness of sport broadcasts and
light entertainment programs. In sports broadcasts, the commentators’ voices
are positioned clearly at the center, while the atmosphere inside the stadium is
realistically conveyed by the peripheral delivery of the sounds of the fans in a
suitable space.
Action Game
This program is suitable for action games, such as car racing and fighting games.
The reality of, and emphasis on, various effects makes the player feel like they are
right in the middle of the action, allowing for greater concentration. Use this
program in combination with Compressed Music Enhancer for a more dynamic
and strong sound field.
Roleplaying Game
This program is suitable for role-playing and adventure games. This program
adds depth to the sound field for natural and realistic reproduction of
background music, special effects, and dialogue from a wide variety of scenes.
Use this program in combination with Compressed Music Enhancer for a clearer
and more spatial sound field.
Music Video
This program allows you to enjoy videos of pop, rock, and jazz concerts, as if you
were there yourself. Immerse yourself in the hot concert atmosphere thanks to
the vividness of the singers and solos on stage, a presence sound field that
emphasizes the beat of rhythm instruments, and a surround sound field that
reproduces the space of a big live hall.
The following sound programs are optimized for listening to music sources.
You can also select stereo playback.
CLASSICAL
Hall in Munich
This program simulates a Munich concert hall with approximately 2,500 seats
that uses stylish wood for the interior finishing. Fine, beautiful reverberations
spread richly, creating a calming atmosphere. The listener’s virtual seat is at the
center left of the arena.
Hall in Vienna
This program simulates a 1,700-seat, middle-sized concert hall with a shoebox
shape that is traditional in Vienna. Pillars and ornate carvings create extremely
complex reverberations from all around the audience, producing a very full, rich
sound.
Chamber
This program creates a relatively wide space with a high ceiling, like an audience
hall in a palace. It offers pleasant reverberations that are suitable for courtly
music and chamber music.
LIVE/CLUB
Cellar Club
This program simulates an intimate concert venue with a low ceiling and homey
atmosphere. A realistic, live sound field delivers powerful sounds that make you
feel as if you are sitting in the front row in front of a small stage.
The Roxy Theatre
This program creates the sound field of a 460-seat rock music concert venue in
Los Angeles. The listener’s virtual seat is at the center left of the hall.
The Bottom Line
This program creates the sound field at stage front in The Bottom Line, a famous
New York jazz club once. The floor can seat 300 people to the left and right in a
sound field offering real and vibrant sound.
STEREO
2ch Stereo
Use this program to mix down multichannel sources to 2 channels. When
multichannel signals are input, they are down mixed to 2 channels and output
from the front speakers (this program does not utilize CINEMA DSP).
7ch Stereo
Use this program to output sound from all speakers. When you play back
multichannel sources, the unit mixes down the source to 2 channels, and then
outputs the sound from all speakers. This program creates a larger sound field
and is ideal for background music at parties.
Y
CINEMA DSP 3D (p.58) and Virtual CINEMA DSP (p.60) do not work when “2ch Stereo” or “7ch Stereo” is selected.
En
59
⬛ Enjoying sound field effects without surround speakers
(Virtual CINEMA DSP)
If you select one of the sound programs (except 2ch Stereo and 7ch Stereo) when no surround
speakers are connected, the unit utilizes Yamaha’s original virtual surround technology to
reproduce up to 7-channel surround sound and enable you to enjoy the well-oriented sound
field only with the front-side speakers. We recommend using presence speakers in order to
enjoy more effective stereoscopic sound field.
X
When Virtual CINEMA DSP is working, “VIRTUAL” lights up in the front display.
⬛ Enjoying surround sound with 5 speakers placed in
front (Virtual CINEMA FRONT)
If you have surround speakers but there is no space to place them in the rear of your room, you
can place them in the front (p.18) and enjoy multichannel surround sound using Virtual
CINEMA FRONT.
When “Layout (Surround)” (p.108) in the “Setup” menu is set to “Front”, the unit creates the
virtual surround speakers in the rear side to allow you to enjoy multichannel surround sound
with the 5 speakers placed in the front.
X
When Virtual CINEMA FRONT is working, “VIRTUAL” lights up in the front display.
⬛ Enjoying surround sound with headphones
(SILENT CINEMA)
You can enjoy surround or sound field effects, like a multichannel speaker system, with stereo
headphones by connecting the headphones to the PHONES jack and selecting a sound
program or a surround decoder.
En
60
⬛ Playing back in extended multichannel (surround
decoder)
Enjoying unprocessed playback
You can play back input sources without any sound field effect processing.
The surround decoder enables unprocessed multichannel playback from 2-channel or
multichannel sources.
⬛ Playing back in original channels
(straight decode)
Y
• Speakers that produce sounds will change depending on your speaker system and the selected decode type
When the straight decode mode is enabled, the unit produces stereo sound from the front
(p.101).
speakers for 2-channel sources such as CDs, and produces unprocessed multichannel sounds
• For details on each decoder, see “Glossary” (p.140).
for multichannel sources.
1
1
Press STRAIGHT.
Press SUR. DECODE to select a surround decoder.
Each time you press the key, the surround decoder changes.
Each time you press the key, the straight decode mode is enabled or disabled.
OUT
OUT
2
ECO
STRAIGHT
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
†‡ Dsur
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
Y
FPL
FPR
SL
SW
SR
SBL SB SBR
Auto
Uses the decoder automatically selected by input source. The DTS Neural:X
decoder is selected for DTS sources and the Dolby Surround decoder is
selected for other sources.
bDsur
Use the Dolby Surround decoder suitable for all sources. A real acoustic space
(including overhead) will be created especially when object-based audio
(such as Dolby Atmos content) is played.
Neural:X
Use the DTS Neural:X decoder suitable for all sources. A real acoustic space
(including overhead) will be created especially when object-based audio
(such as DTS:X content) is played.
Neo:6 Cinema
Uses the DTS Neo:6 decoder (or DTS-ES Matrix decoder) suitable for movies.
Sounds will be output from the surround/surround back speakers.
Neo:6 Music
Uses the DTS Neo:6 decoder (or DTS-ES Matrix decoder) suitable for music.
Sounds will be output from the surround/surround back speakers.
• To enable 6.1/7.1-channel playback from 5.1-channel sources when surround back speakers are used, select a
surround decoder (p.61).
• If “Layout (Surround)” (p.108) in the “Setup” menu is set to “Front”, Virtual CINEMA FRONT (p.60) works when
VOL. MUTE VIRTUAL
multichannel source is played back.
Y
• You can adjust the surround decoder parameters in “DSP Program menu items” (p.101).
• When the Dolby Surround decoder is selected, virtual surround processing (such as Virtual CINEMA FRONT)
(p.61), YPAO Volume (p.91) or Compressed Music Enhancer (p.62) does not work.
• If the Dolby Surround decoder is selected when only one surround back speaker is used, no sound is output
from the surround back speaker (except when a Dolby Atmos content is played).
• When the Neural:X decoder is selected, virtual surround processing (such as Virtual CINEMA FRONT) (p.58),
YPAO Volume (p.91), Dialogue Level (p.91), Extra Bass (p.92) or Compressed Music Enhancer (p.62) does not
work.
• For some input sources, the selected surround decoder does not work.
En
61
Enjoying pure high fidelity sound
(Pure Direct)
When the Pure Direct is enabled, the unit plays back the selected source
HDMI
1
2
3
4
5
with the least circuitry in order to reduce the electrical noise from other
V-AUX
circuitry (such as the front display). It allows you to enjoy Hi-Fi sound
AUDIO
1
2
3
4
quality.
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
1
Compressed Music Enhancer adds depth and breadth to the sound,
3
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
OUT
2
ECO
TOP MENU
it was compressed. This function can be used along with any other sound
4
LINK MASTER
PROGRAM MUTE
allowing you to enjoy a dynamic sound close to the original sound before
Press PURE DIRECT.
Each time you press the key, the Pure Direct is enabled or disabled.
SCENE
2
1
PURE DIRECT
VOLUME
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
modes.
1
Press ENHANCER.
Each time you press the key, Compressed Music Enhancer is
Y
POP-UP/MENU
ON
SCREEN
Playing back digitally compressed formats
(such as MP3, etc.) with enriched sound
(Compressed Music Enhancer)
enabled or disabled.
When the Pure Direct is enabled, the following functions are not available.
OPTION
“ENHANCER” lights up
– Some settings for the speakers or sound programs
ENTER
– Operating the on-screen menu and some items in the “Option” menu
TUNING
– Using the multi-zone function
BAND
– Viewing information on the front display (when not in operation)
PRESET
MUSIC
SLEEP
1
2
3
4
5
6
7
8
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
Y
STRAIGHT
• Compressed Music Enhancer does not work on the following audio sources.
ENHANCER PURE DIRECT
INFO
Enhancer On
SUR.DECODE
SUR. DECODE STRAIGHT
MOVIE
2
ECO
DISPLAY
MODE
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
OUT
RETURN
– Signals whose sampling frequency is over 48 kHz
– DSD audio
9
0
MEMORY
• You can also use “Enhancer” (p.92) in the “Option” menu to enable/disable
ENT
Compressed Music Enhancer.
• This function is also available in Zone2.
En
62
Listening to FM/AM radio
You can tune into a radio station by specifying its frequency or selecting
1
2
3
4
5
Y
V-AUX
AUDIO
1
2
5
1
3
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
• The radio frequencies differ depending on the country or region where the unit is
4
AV
MAIN
ZONE 2
TUNER
2
OUT
FM 87.50MHz
3
Numeric keys: Enter a frequency directly. For example, to select
for AM. Depending on your country or region, set the frequency steps to
98.50 MHz, press “9”, “8”, “5” and “0” (or ENT).
100 kHz for FM and 10 kHz for AM.
BAND
PRESET
TUNING
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
DISPLAY
TUNING
Use the following keys to set a frequency.
about a second to search stations automatically.
At the factory, the frequency step setting is set to 50 kHz for FM and 9 kHz
BAND
ENHANCER PURE DIRECT
1
2
OUT
2
ECO
Set the unit to standby mode.
FM 98.50MHz
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
When holding down STRAIGHT on the front panel, press
“TUNED” lights up when the unit is receiving an FM/AM radio
MAIN ZONE z.
station signal.
“STEREO” lights up when the unit is receiving a stereo FM radio
MAIN ZONE z
Numeric keys
ENT
VOL. MUTE VIRTUAL
TUNING: Increase/decrease the frequency. Hold down the key for
(Taiwan, Brazil, Asia and General models only)
ENTER
MODE
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
2
ECO
Setting the frequency steps
OPTION
RETURN
Press BAND to select a band (FM or AM).
4
VOLUME
ON
SCREEN
Press TUNER to select “TUNER” as the input source.
LINK MASTER
• If you cannot obtain good reception on the radio, adjust the direction of the FM/AM
POP-UP/MENU
TOP MENU
1
2
antennas.
3
PROGRAM MUTE
being used. The explanation of this section uses a display with frequencies used in
U.K. and Europe models.
SCENE
1
Selecting a frequency for reception
from registered radio stations.
HDMI
signal.
Y
“Wrong Station!” appears when you enter a frequency that is out of reception range.
PROGRAM
3
You can switch between “Stereo” (stereo) and “Mono” (monaural) for FM radio
reception in “FM Mode” (p.93) in the “Option” menu. When the signal reception for an
Press PROGRAM repeatedly to select “TU”.
LINK MASTER
OUT
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
TU••••FM50/AM9
4
5
X
STRAIGHT
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
Press STRAIGHT to select “FM100/AM10”.
Press MAIN ZONE z to set the unit to standby mode and
turn it on again.
En
63
FM radio station is unstable, switching to monaural may improve it.
Registering favorite radio stations
(presets)
You can register up to 40 radio stations as presets. Once you have
HDMI
1
2
3
4
5
registered stations, you can easily tune into them by selecting their
V-AUX
preset numbers.
AUDIO
1
2
3
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
TUNER
⬛ Selecting a preset station
Tune into a registered radio station by selecting its preset number.
1
2
Press TUNER to select “TUNER” as the input source.
Press PRESET repeatedly to select the desired radio
X
station.
You can automatically register FM radio stations that have strong signals by using
You can also enter a preset number (01 to 40) directly by using the
“Auto Preset” (p.66).
Numeric keys after pressing PRESET once.
SCENE
2
1
3
PROGRAM MUTE
4
ON
SCREEN
OUT
ECO
1
OPTION
2
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
01:FM 98.50MHz
Select a radio station manually and register it to a preset number.
VOLUME
POP-UP/MENU
TOP MENU
LINK MASTER
⬛ Registering a radio station
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
Y
Follow “Selecting a frequency for reception” (p.63) to
• “No Presets” appears when no radio stations are registered.
tune into the desired radio station.
• “Wrong Num.” appears when an invalid number is entered.
• “Empty” appears when a preset number not in use is entered.
ENTER
RETURN
2
DISPLAY
BAND
MODE
TUNING
PRESET
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
Hold down MEMORY for seconds.
X
The first time that you do register a station, the selected radio
To clear preset stations, use “Clear Preset” or “Clear All Preset” (p.66).
station will be registered to the preset number “01”. Thereafter,
each radio station you select will be registered to the next empty
ENHANCER PURE DIRECT
(unused) preset number after the most recently registered
number.
Numeric keys
MEMORY
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
OUT
2
ECO
VOL. MUTE VIRTUAL
01:FM 98.50MHz
FPL
FPR
SL
SW
SR
SBL SB SBR
Preset number
X
To select a preset number for registering, press MEMORY once after tuning into
the desired radio station, press PRESET to select a preset number, and then
press MEMORY again.
LINK MASTER
OUT
2
ECO
02:Empty
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
“Empty” (not in use) or the frequency currently registered
En
64
Radio Data System tuning
(U.K. and Europe models only)
2
3
4
5
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
“Clock Time”, when it is tuned into a Radio Data System broadcasting
AV
station.
MAIN
ZONE 2
⬛ Displaying the Radio Data System
information
SCENE
2
1
3
PROGRAM MUTE
4
1
VOLUME
station.
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
ENTER
RETURN
DISPLAY
X
Cursor keys
ENTER
RETURN
We recommend using “Auto Preset” to tune into the Radio Data System
BAND
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
OUT
2
ECO
VOL. MUTE VIRTUAL
Program Type
FPL
FPR
SL
SW
SR
SBL SB SBR
procedure below to set the traffic information station.
1
When “TUNER” is selected as the input source, press
2
Use the Cursor keys to select “Traffic Program”
About 3 seconds later, the corresponding information for the
displayed item appears.
2
ECO
X
• To search upward/downward from the current frequency, press the Cursor
keys (q/w) while “READY” is displayed.
• Texts in parentheses denote indicators on the front display.
The following screen appears for about 3 seconds when the search
finishes.
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
ENTER again to start the search immediately.
• To cancel the search, press RETURN.
Item name
OUT
receives traffic information. To enable this function, follow the
The traffic information station search will start in 5 seconds. Press
Press INFO.
ENHANCER PURE DIRECT
INFO
When “TUNER” is selected as the input source, the unit automatically
(TrafficProgram) and press ENTER.
Each time you press the key, the displayed item changes.
SUR. DECODE STRAIGHT
MOVIE
broadcasting stations (p.66).
2
PRESET
⬛ Receiving traffic information
automatically
OPTION.
OPTION
MODE
TUNING
Tune into the desired Radio Data System broadcasting
Frequency
displayed if the radio station does not provide the Radio Data System service.
data, such as “Program Service”, “Program Type,” “Radio Text” and
AUDIO
2
Frequency
“Program Service”, “Program Type”, “Radio Text”, and “Clock Time” are not
many countries. The unit can receive various types of Radio Data System
V-AUX
1
Decoder name
Y
Radio Data System is a data transmission system used by FM stations in
HDMI
1
Audio Decoder
CLASSICS
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
OUT
2
ECO
TP FM101.30MHz
Information
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
Traffic information station (frequency)
Program Service
Program service name
Program Type
Current program type
Radio Text
Information on the current program
Clock Time
Current time
DSP Program
Sound mode name
Y
“TP Not Found” appears for about 3 seconds when no traffic information
En
65
stations are found.
⬛ Browse screen
Operating the radio on the TV
You can view the radio information or select a radio station on the TV.
HDMI
1
2
3
1
4
5
a
Press TUNER to select “TUNER” as the input source.
c
V-AUX
The playback screen is displayed on the TV.
AUDIO
1
2
3
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
4
AV
MAIN
ZONE 2
TUNER
SCENE
2
1
3
PROGRAM MUTE
⬛ Playback screen
b
b
a
4
a Preset station list
Displays the list of preset stations. Use the Cursor keys to select a preset station
and press ENTER to tune into it.
c
VOLUME
b Preset number
c Operation menu
POP-UP/MENU
TOP MENU
ON
SCREEN
Press the Cursor key (r) and then use the Cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
OPTION
ENTER
RETURN
DISPLAY
BAND
Menu operation keys
Cursor keys
ENTER
a Radio station information
Menu
Displays the information of the selected radio station such as the selected band
(FM/AM) and frequency.
Submenu
Memory
Auto Preset
Automatically registers FM radio stations
with strong signals (up to 40 stations).
Clear Preset
Clear the preset station selected in the
list.
Clear All Preset
Clear all the preset stations.
MODE
TUNING
(U.K. and Europe models only)
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
3
When tuning into a Radio Data System broadcasting station (p.65), the Radio
Data System information (“Program Service”, “Program Type,” “Radio Text”
and “Clock Time”) is also displayed.
Utility
4
b TUNED/STEREO indicators
“TUNED” lights up when a signal is received from a radio station.
1 Page Up
“STEREO” lights up when a stereo signal is received.
c Operation menu
Press the Cursor key (r) and then use the Cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
Menu
Function
Browse
Moves to the browse screen (preset station list).
Screen Off
Closes the screen display and shows the background. Press
one of the Menu operation keys to redisplay it.
Function
Registers the current station to the preset
number selected in the list.
1 Page Down
Moves to the previous/next page of the
list.
Now Playing
Moves to the playback screen.
Screen Off
Closes the screen display and shows the
background. Press one of the Menu
operation keys to redisplay it.
Y
(U.K. and Europe models only)
Only Radio Data System broadcasting stations are stored automatically by “Auto
Preset”.
En
66
Playing back music via Bluetooth
You can play back music files stored on a Bluetooth device (such as
smartphones) on the unit. Also, you can enjoy audio played back on the
HDMI
1
2
3
4
unit using Bluetooth speakers/headphones.
5
Playing back Bluetooth device music on the
unit
V-AUX
AUDIO
1
2
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
Follow the procedure below to establish a Bluetooth connection
AV
MAIN
ZONE 2
between a Bluetooth device (such as smartphones) and the unit, and
play back music stored the Bluetooth device on the unit.
BLUETOOTH
The unit
SCENE
2
1
3
PROGRAM MUTE
4
Bluetooth device
(such as smartphones)
Y
The unit does not support video playback via Bluetooth.
1
VOLUME
Press BLUETOOTH to select “Bluetooth” as the input
source.
POP-UP/MENU
TOP MENU
ON
SCREEN
2
OPTION
The unit
ENTER
RETURN
the unit) from the available device list.
Bluetooth speakers/
headphones
DISPLAY
A connection between the Bluetooth device and the unit will be
made.
BAND
MODE
TUNING
External device
operation keys
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
Y
If the pass key is required, enter the number “0000”.
• To use the Bluetooth function, set “Bluetooth” (p.117) in the “Setup” menu to “On”.
ENHANCER PURE DIRECT
• You cannot make Bluetooth connections to a Bluetooth device (such as smartphones)
3
4
On the Bluetooth device, select the unit (network name of
and Bluetooth speakers/headphones at the same time.
3
On the Bluetooth device, select a song and start playback.
The playback screen (artist name, album name and song title) is
• Stand the wireless antenna upright for connecting to a Bluetooth device wirelessly.
displayed on the TV.
For details, see “Preparing the wireless antenna” (p.35).
X
X
For details on supported Bluetooth devices, see “Supported devices and file formats”
• If the unit detects the Bluetooth device previously connected, the unit automatically
connects to the Bluetooth device after Step 1. To establish another Bluetooth
(p.143).
connection, first terminate the current Bluetooth connection.
• To terminate the Bluetooth connection, perform one of the following operations.
– Perform the disconnect operation on the Bluetooth device.
– Select an input source other than “Bluetooth” on the unit.
– Select “Disconnect” in “Audio Receive” (p.104) in the “Setup” menu.
• You can use the External device operation keys (a, s, d, f, g) on the
remote control to control playback.
En
67
X
Enjoying audio using Bluetooth
speakers/headphones
Follow the procedure below to establish a Bluetooth connection
HDMI
1
2
3
4
5
2
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
Input selection keys
AV
MAIN
ZONE 2
3
While the Bluetooth speakers/headphones are in the
pairing mode, use the Cursor keys to select “CONNECT”
and press ENTER.
played back on the unit using Bluetooth speakers/headphones.
Y
To use this function, set “Transmitter” (p.117) in the “Setup” menu to “On”.
1
SCENE
2
1
5
between Bluetooth speakers/headphones and the unit, and enjoy audio
V-AUX
AUDIO
1
The checkmark indicates the Bluetooth device currently selected.
4
Use the Input selection keys (except BLUETOOTH) to
select an input source.
PROGRAM MUTE
VOLUME
POP-UP/MENU
TOP MENU
ON
SCREEN
ON SCREEN
OPTION
2
3
Cursor keys
ENTER
ENTER
RETURN
DISPLAY
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
speakers/headphones.
6
To exit from the menu, press ON SCREEN.
X
SUR. DECODE STRAIGHT
MUSIC
unit will be reproduced from the Bluetooth
“Bluetooth” ➞ “Audio Send” ➞ “Device Search” and
“OK”.
PRESET
MOVIE
When the connection process finishes, audio played back on the
Use the Cursor keys and ENTER to select “Setup” ➞
The list of Bluetooth devices (BD addresses) is displayed.
BAND
MODE
TUNING
Press ON SCREEN.
To terminate the Bluetooth connection, perform the disconnect operation on the
ENHANCER PURE DIRECT
Bluetooth speakers/headphones.
3
4
Y
• AirPlay and DSD audio cannot be delivered.
• When the Pure Direct is enabled, input sources other than the network sources and
USB cannot be delivered.
4
Use the Cursor keys and ENTER to check the desired
Bluetooth speakers/headphones.
En
68
Playing back music stored on a USB storage device
You can play back music files stored on a USB storage device on the unit.
1
2
3
4
5
V-AUX
AUDIO
1
2
3
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
format).
Follow the procedure below to operate the USB storage device contents
X
and start playback.
For details on playable file formats, see “Supported devices and file formats” (p.143).
3
You can control the USB memory device with the menu displayed on the
TV screen.
USB
Connecting a USB storage device
SCENE
2
1
Playback of USB storage device contents
The unit supports USB mass storage class devices (FAT16 or FAT32
HDMI
4
1
Press USB to select “USB” as the input source.
The browse screen is displayed on the TV.
PROGRAM MUTE
VOLUME
1
Connect the USB storage device to the USB jack.
The unit (front)
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
1
PHONES
ENTER
SILENT CINEMA
RETURN
USB
5V
TONE CONTROL
INPUT
1A
DISPLAY
BAND
MODE
TUNING
PRESET
X
SUR. DECODE STRAIGHT
MOVIE
MUSIC
If playback is ongoing on your USB storage device, the playback screen is
ENHANCER PURE DIRECT
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
displayed.
3
4
USB storage device
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
OUT
2
ECO
Connected
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
X
If the USB storage device contains many files, it may take time to load the them. In this
case, “Loading...” appears in the front display.
Y
• Stop playback of the USB storage device before disconnect it from the USB jack.
• Connect a USB storage device directly to the USB jack of the unit. Do not use
extension cables.
• The unit cannot charge USB devices while it is in standby mode.
En
69
2
Use the Cursor keys to select an item and press ENTER.
If a song is selected, playback starts and the playback screen is
displayed.
HDMI
1
2
3
4
5
⬛ Browse screen
a
b
c
e
V-AUX
AUDIO
1
2
3
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
d
a Status indicators
SCENE
2
1
3
PROGRAM MUTE
4
Display the current shuffle/repeat settings (p.71) and playback status (such as
play/pause).
VOLUME
POP-UP/MENU
TOP MENU
ON
SCREEN
RETURN
DISPLAY
BAND
b List name
• To return to the previous screen, press RETURN.
c Contents list
• To return to the top screen during menu operations on the browse screen,
OPTION
ENTER
X
hold down RETURN.
Menu operation keys
Cursor keys
ENTER
RETURN
• Files not supported by the unit cannot be selected.
d Item number/total
• If the unit detects a series of unsupported files (such as images and hidden
e Operation menu
files) during playback, playback stops automatically.
Press the Cursor key (r) and then use the Cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
MODE
TUNING
Displays the list of USB storage device contents. Use the Cursor keys to select an
item and press ENTER to confirm the selection.
PRESET
SUR. DECODE STRAIGHT
Menu
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
Function
ENHANCER PURE DIRECT
1 Page Up
Moves to the previous/next page of the list.
1 Page Down
10 Pages Up
Moves 10 pages forward/backward.
10 Pages Down
En
70
Return
Returns to the higher-level list.
Now Playing
Moves to the playback screen.
Screen Off
Closes the screen display and shows the background.
Press one of the Menu operation keys to redisplay it.
⬛ Playback screen
⬛ Shuffle/repeat settings
You can configure the shuffle/repeat settings for playback of USB storage
a
b
device contents.
HDMI
1
2
3
4
5
c
V-AUX
AUDIO
1
2
5
1
3
4
2
TUNER
1
When “USB” is selected as the input source, press
OPTION.
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
2
2
1
3
PROGRAM MUTE
“Repeat” (Repeat) and press ENTER.
a Status indicators
SCENE
X
Display the current shuffle/repeat settings (p.71) and playback status (such as
play/pause).
4
• To return to the previous screen during menu operations, press RETURN.
b Playback information
VOLUME
Use the Cursor keys to select “Shuffle” (Shuffle) or
• Texts in parentheses denote indicators on the front display.
Displays the artist name, album name, song title, and elapsed time.
OPTION
ENTER
RETURN
DISPLAY
BAND
3
Use the Cursor keys to select scrollable information.
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
Menu operation keys
Cursor keys
ENTER
RETURN
c Operation menu
Press the Cursor key (r) and then use the Cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
Menu
External device
operation keys
PRESET
Item
Shuffle
(Shuffle)
Function
MODE
TUNING
Use the Cursor keys (e/r) to select a setting.
Browse
Moves to the browse screen.
Screen Off
Closes the screen display and shows the background.
Press one of the Menu operation keys to redisplay it.
Setting
Off (Off)
Turns off the shuffle function.
On (On)
Plays back songs in the current album (folder)
in random order.
“x” appears on the TV screen.
SUR. DECODE STRAIGHT
MOVIE
MUSIC
ENHANCER PURE DIRECT
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
Function
X
You can use the External device operation keys (a, s, d, f, g) on the remote
Off (Off)
Repeat
(Repeat)
control to control playback.
One (One)
All (All)
Turns off the repeat function.
Plays back the current song repeatedly.
“c” appears on the TV screen.
Plays back all songs in the current album
(folder) repeatedly.
“v” appears on the TV screen.
4
En
71
To exit from the menu, press OPTION.
Playing back music stored on media servers (PCs/NAS)
You can play back music files stored on your PC or DLNA-compatible NAS on the unit.
Y
• To use this function, the unit and your PC must be connected to the same router (p.35). You can check whether
the network parameters (such as the IP address) are properly assigned to the unit in “Network” (p.124) in the
“Information” menu.
• The audio may be interrupted while using the wireless network connection. In this case, use the wired network
connection.
X
For details on playable file formats, see “Supported devices and file formats” (p.143).
Media sharing setup
To play back music files stored on your PC or DLNA-compatible NAS, first you need to configure
the media sharing setting on each music server.
⬛ For a PC with Windows Media Player installed
The setting procedure may vary depending on the PC and Windows Media Player version (The
following procedure is a setup example for Windows Media Player 12).
1
2
3
4
5
Start Windows Media Player 12 on your PC.
Select “Stream”, then “Turn on media streaming”.
Click “Turn on media streaming”.
Select “Allowed” from the drop-down list next to the unit’s model name.
Click “OK” to exit.
⬛ For a PC or a NAS with other DLNA server software
installed
Refer to the instruction manual for the device or software and configure the media sharing
settings.
En
72
Playback of PC music contents
HDMI
1
2
3
4
5
3
Use the Cursor keys to select an item and press ENTER.
Follow the procedure below to operate the PC music contents and start
If a song is selected, playback starts and the playback screen is
playback.
displayed.
You can control the PC/NAS with the menu displayed on the TV screen.
V-AUX
AUDIO
1
2
5
1
3
4
2
TUNER
1
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
Press NET repeatedly to select “SERVER” as the input
source.
NET
The browse screen is displayed on the TV.
SCENE
2
1
3
PROGRAM MUTE
4
X
VOLUME
• To return to the previous screen, press RETURN.
POP-UP/MENU
TOP MENU
ON
SCREEN
• To return to the top screen during menu operations on the browse screen,
OPTION
ENTER
RETURN
DISPLAY
hold down RETURN.
• Files not supported by the unit cannot be selected.
Cursor keys
ENTER
RETURN
files) during playback, playback stops automatically.
If playback of a music file selected from the unit is ongoing on your PC, the
MODE
TUNING
• If the unit detects a series of unsupported files (such as images and hidden
X
BAND
PRESET
playback screen is displayed.
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
2
Use the Cursor keys to select a music server and press
ENTER.
En
73
⬛ Browse screen
a
b
c
HDMI
1
2
3
4
5
⬛ Playback screen
a
b
V-AUX
e
AUDIO
1
2
3
c
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
d
3
PROGRAM MUTE
a Status indicators
a Status indicators
SCENE
2
1
4
Display the current shuffle/repeat settings (p.75) and playback status (such as
play/pause).
b Playback information
b List name
VOLUME
Displays the artist name, album name, song title, and elapsed time.
c Contents list
POP-UP/MENU
TOP MENU
ON
SCREEN
Displays the list of PC content. Use the Cursor keys to select an item and press
ENTER to confirm the selection.
OPTION
ENTER
RETURN
DISPLAY
Menu operation keys
Cursor keys
ENTER
BAND
MODE
TUNING
External device
operation keys
PRESET
Display the current shuffle/repeat settings (p.75) and playback status (such as
play/pause).
Use the Cursor keys to select scrollable information.
c Operation menu
Press the Cursor key (r) and then use the Cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
d Item number/total
e Operation menu
Press the Cursor key (r) and then use the Cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
Menu
Function
Browse
Moves to the browse screen.
Screen Off
Closes the screen display and shows the background.
Press one of the Menu operation keys to redisplay it.
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
Menu
ENHANCER PURE DIRECT
Function
1 Page Up
Moves to the previous/next page of the list.
1 Page Down
10 Pages Up
X
• You can use the External device operation keys on the remote control to control
Moves 10 pages forward/backward.
10 Pages Down
Return
Returns to the higher-level list.
Now Playing
Moves to the playback screen.
Screen Off
Closes the screen display and shows the background.
Press one of the Menu operation keys to redisplay it.
En
playback (some functions may not work depending on the PC/NAS).
• You can also use a DLNA-compatible Digital Media Controller (DMC) to control
playback. For details, see “DMC Control” (p.96).
74
⬛ Shuffle/repeat settings
You can configure the shuffle/repeat settings for the playback of PC
music content.
HDMI
1
2
3
1
4
5
V-AUX
AUDIO
1
2
5
1
3
4
2
TUNER
When “SERVER” is selected as the input source, press
OPTION.
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
2
“Repeat” (Repeat) and press ENTER.
SCENE
2
1
3
Use the Cursor keys to select “Shuffle” (Shuffle) or
X
4
• To return to the previous screen during menu operations, press RETURN.
PROGRAM MUTE
VOLUME
• Text in parentheses denotes indicators on the front display.
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
ENTER
RETURN
DISPLAY
BAND
MODE
TUNING
PRESET
OPTION
3
Use the Cursor keys (e/r) to select a setting.
Item
Cursor keys
ENTER
RETURN
Shuffle
(Shuffle)
Setting
Off (Off)
Turns off the shuffle function.
On (On)
Plays back songs in the current album (folder)
in random order.
“x” appears on the TV screen.
SUR. DECODE STRAIGHT
MOVIE
Function
MUSIC
Off (Off)
ENHANCER PURE DIRECT
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
Repeat
(Repeat)
One (One)
All (All)
Turns off the repeat function.
Plays back the current song repeatedly.
“c” appears on the TV screen.
Plays back all songs in the current album
(folder) repeatedly.
“v” appears on the TV screen.
4
To exit from the menu, press OPTION.
En
75
Listening to Internet radio
You can listen to Internet radio stations from all over the world.
1
2
3
4
V-AUX
• To use this function, the unit must be connected to the Internet (p.35). You can check
3
4
whether the network parameters (such as the IP address) are properly assigned to
2
TUNER
5
AUDIO
1
2
5
1
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
1
NET
Press NET repeatedly to select “NET RADIO” as the input
source.
the unit in “Network” (p.124) in the “Information” menu.
The browse screen is displayed on the TV.
• You may not be able to receive some Internet radio stations.
• The unit uses the airable.Radio service. airable is a service of Tune In GmbH.
• This service may be discontinued without notice.
SCENE
2
1
Playback of Internet radio
Y
HDMI
3
4
• Folder names are different depending on the language.
PROGRAM MUTE
VOLUME
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
ENTER
RETURN
DISPLAY
Cursor keys
ENTER
RETURN
2
MODE
TUNING
Use the Cursor keys to select an item and press ENTER.
If an Internet radio station is selected, playback starts and the
BAND
PRESET
playback screen is displayed.
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
4
X
• To return to the previous screen, press RETURN.
• To return to the top screen during menu operations on the browse screen, hold down
RETURN.
En
76
⬛ Browse screen
a
b
c
HDMI
1
2
3
4
5
⬛ Playback screen
a
b
V-AUX
2
3
c
e
AUDIO
1
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
d
SCENE
2
1
3
PROGRAM MUTE
4
a Playback indicator
a Playback indicator
b List name
b Playback information
Displays the station name, album name, song title, and elapsed time.
c Contents list
VOLUME
Displays the list of Internet radio content. Use the Cursor keys to select an item
and press ENTER to confirm the selection.
POP-UP/MENU
TOP MENU
ON
SCREEN
Press the Cursor key (r) and then use the Cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
d Item number/total
OPTION
e Operation menu
ENTER
RETURN
DISPLAY
Menu operation keys
Cursor keys
ENTER
Use the Cursor keys (q/w) to select scrollable information.
c Operation menu
Press the Cursor key (r) and then use the Cursor keys (q/w) to select an item.
Press ENTER to confirm the selection.
Menu
Function
Add to favorites
Adds the current station to the “Favorites” folder (p.78).
Browse
Moves to the browse screen.
Screen Off
Closes the screen display and shows the background.
Press one of the Menu operation keys to redisplay it.
BAND
MODE
TUNING
External device
operation keys
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
Menu
Add to favorites
(Remove from
favorites)
Function
Adds/removes the station selected in the list to/from the
“Favorites” folder (p.78).
4
1 Page Up
Moves to the previous/next page of the list.
1 Page Down
X
• You can use the External device operation key (s) on the remote control to stop
playback.
10 Pages Up
Moves 10 pages forward/backward.
10 Pages Down
Return
Returns to the higher-level list.
Now Playing
Moves to the playback screen.
Screen Off
Closes the screen display and shows the background.
Press one of the Menu operation keys to redisplay it.
En
77
• Some information may not be available depending on the station.
Registering favorite Internet radio stations (Favorites)
By registering your favorite Internet radio stations to “Favorites”, you
can quickly access to them from the “Favorites” folder in the browse
HDMI
1
2
3
4
5
screen.
V-AUX
X
AUDIO
1
2
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
AV
MAIN
ZONE 2
You can also register up to 40 favorite USB, Bluetooth and network contents as
shortcuts (p.85).
⬛ Registering the station on the
browse/playback screen
SCENE
2
1
3
PROGRAM MUTE
4
1
VOLUME
screen or start playback of it to display the playback
screen.
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
Cursor keys
ENTER
ENTER
RETURN
DISPLAY
Select the desired Internet radio station in the browse
2
Press the Cursor key (r) to select “Add to favorites” and
press ENTER.
BAND
MODE
TUNING
The selected station is added to the “Favorites” folder.
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
Radio stations registered to favorites are displayed with “★”.
ENHANCER PURE DIRECT
Browse screen
X
To remove a station that is registered to favorites, select the station and then select
“Remove from favorites”.
En
78
Playing back iTunes/iPhone music with AirPlay
Playback of iTunes/iPhone music contents
The AirPlay function allows you to play back iTunes/iPhone music on the unit via network.
iTunes
Follow the procedure below to play back iTunes/iPhone music contents on the unit.
PC
(wired or wireless)
1
Router
Turn on the unit, and start iTunes on the PC or display the playback screen
on the iPhone.
The unit
If the iTunes/iPhone recognizes the unit, the AirPlay icon appears.
iOS 10 (example)
(wired or wireless)
iPhone/iPad/
iPod touch
iOS 9 (example)
iTunes (example)
Y
If the icon does not appear, check whether the unit and PC/iPhone are connected to the router properly.
Y
2
• To use this function, the unit and your PC or iPhone must be connected to the same router. You can check
whether the network parameters (such as the IP address) are properly assigned to the unit in “Network” (p.124)
On the iTunes/iPhone, click (tap) the AirPlay icon and select the unit
(network name of the unit) as the audio output device.
in the “Information” menu.
• When using a multiple SSID router, access to the unit might be restricted depending on the SSID to connect.
3
Connect the iPhone to the SSID which can access the unit.
Select a song and start playback.
X
The unit automatically selects “AirPlay” as the input source and starts playback.
• For details on supported iPhone devices, see “Supported devices and file formats” (p.143).
The playback screen is displayed on the TV.
• You can restrict access to the unit using the AirPlay password (p.88).
Y
The playback screen is available only when your TV is connected to the unit via HDMI.
En
79
⬛ Playback screen
X
• You can turn on the unit automatically when starting playback on iTunes or iPhone by
a
b
setting “Network Standby” (p.115) in the “Setup” menu to “On”.
• You can edit the network name (the unit’s name on the network) displayed on
HDMI
1
2
3
iTunes/iPhone in “Network Name” (p.116) in the “Setup” menu.
4
5
V-AUX
• You can adjust the unit’s volume from the iTunes/iPhone during playback. To disable
4
volume controls from iTunes/iPhone, set “Volume Interlock” (p.96) in the “Input”
AUDIO
1
2
3
c
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
menu to “Off”.
Caution
When you use iTunes/iPhone controls to adjust volume, the volume may be
unexpectedly loud. This could result in damage to the unit or speakers. If the
volume suddenly increases during playback, stop playback on the
iTunes/iPhone immediately.
SCENE
2
1
3
PROGRAM MUTE
4
a Playback indicator
b Playback information
Displays the artist name, album name, song title, and elapsed/remaining time.
Use the Cursor keys (q/w) to select scrollable information.
VOLUME
c Operation menu
POP-UP/MENU
TOP MENU
ON
SCREEN
Press the Cursor key (r) to select an item. Press ENTER to confirm the selection.
OPTION
ENTER
RETURN
DISPLAY
Menu
Menu operation keys
Cursor keys
ENTER
Screen Off
Function
Closes the screen display and shows the background.
Press one of the Menu operation keys to redisplay it.
BAND
MODE
TUNING
X
External device
operation keys
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
5
6
7
8
9
0
MEMORY
ENT
You can use the External device operation keys (a, s, d, f, g) on the remote
ENHANCER PURE DIRECT
3
control to control playback.
4
En
80
Playing back music in multiple rooms (multi-zone)
⬛ Using the unit’s internal amplifier
The multi-zone function allows you to play back different input sources in the room where the
unit is installed (Main zone) and in another room (Zone2).
Connect the speakers placed in Zone2 to the unit with speaker cables. For details, see
For example, while you are watching TV in the living room (Main zone), another person can
“Connecting Zone2 speakers” (p.26).
listen to radio in the study room (Zone2).
⬛ Using an external amplifier
Connect the external amplifier placed in Zone2 to the unit with a stereo pin cable.
The unit (rear)
T
HDMI (HDCP2.2)
HDMI OUT
(HDCP2.2)
N
1
UT
2
3
(1 BD/DVD)
ARC
ANTENNA
(4 RADIO)
AUDIO 1
(2 TV)
FM
PTICAL
AM
AUDIO 2
Study room (Zone2)
PTICAL
AUDIO 3
Y
ZONE2 OUT jacks
AV 2
VIDEO
COMPONENT VIDEO
COAXIAL
COAXIAL
AV 1
ZONE OUT
PR
PB
ZONE OUT
AUDIO 4
ONO
ZONE 2
AUDIO 5
PR ZONE
SU
1
2
L
GND
2
Living room (Main zone)
R
External amplifier
Audio input
(analog stereo)
Y
Digital and analog audio sources (including FM/AM radio), and Bluetooth, USB, and network sources can be
output to Zone2. To listen to the playback of an external device in Zone2, you need to connect the device to the
L
AUDIO jacks (AV 1-2 or AUDIO 1-5 jacks) of the unit. The party mode (p.84) allows you to play back the same audio
Q
output in Main zone as Zone2, whatever the input audio signal type.
W
R
1
9
Preparing Zone2
Connect the device that will be used in Zone2 to the unit. The connection method varies
2
AUDIO
3
4
5
depending on the amplifier being used (the unit or an external amplifier).
6
7
Zone2
Caution
• Remove the unit’s power cable from the AC wall outlet before connecting speakers or an external
amplifier.
Main zone
• Ensure that the bare wires of the speaker cable do not touch one another or come into contact with
the unit’s metal parts. Doing so may damage the unit or the speakers. If the speaker cables short
circuit, “Check SP Wires” will appear on the front display when the unit is turned on.
X
You can adjust the volume for Zone2 output with the unit. When using an external amplifier with volume control,
set “Volume” (p.118) in the “Setup” menu to “Fixed”.
En
81
⬛ Operating the unit from Zone2 (remote connection)
Remote connections between Yamaha products
You can operate the unit or external devices from Zone2 using the remote control supplied
An infrared signal transmitter is not required if you are using Yamaha products that support
with each device if you connect an infrared signal receiver/emitter to the unit’s REMOTE
remote connections, as the unit does. You can transmit remote control signals by connecting
IN/OUT jacks.
the REMOTE IN/OUT jacks with monaural mini-jack cables and an infrared signal receiver.
REMOTE IN/OUT jacks
REMOTE IN/OUT jacks
IN
TRIGGER OUT
12V 0.1A
HDMI (H
HDMI OUT
(HDCP2.2)
OUT
IN
1
OUT
IN
OUT
OUT
2
(1 BD/DVD)
ARC
REMOTE
REMOTE
(4 RADIO)
FM
OPTICAL
AM
Infrared signal
receiver
AUDIO 2
OPTICAL
AUDIO 3
COAXIAL
AV 1
AV 2
COMPONENT VIDEO
Y
VIDEO
Yamaha products
(up to six, including the unit)
PR
PB
ZONE OUT
AUDIO 4
PHONO
REMOTE
REMOTE
ANTENNA
AUDIO 1
(2 TV)
COAXIAL
REMOTE IN/OUT jacks
IN
AUDIO 5
ZONE 2
GND
Remote control
The unit (rear)
Zone2
Infrared signal
transmitter
External device
(such as a CD player)
Infrared signal
receiver
Remote control
(supplied with each
device)
Zone2
Main zone
En
82
Controlling Zone2
z
HDMI
1
2
3
4
5
V-AUX
AUDIO
1
2
3
4
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
V-AUX
AV 1-2
AUDIO 1-5
TUNER
BLUETOOTH
USB
NET
PHONO
MAIN/ZONE2
SCENE
2
1
3
4
MUTE
1
2
4
station.
Set MAIN/ZONE2 to “ZONE2”.
Refer to the instruction manual for the external device.
For details on the following operations, see the corresponding
Press z (receiver power).
pages.
Each time you press the key, Zone2 output is enabled or disabled.
When Zone2 output is enabled, “ZONE2” lights up in the front
display.
3
VOLUME
VOLUME
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
Use the following keys to select an input source.
TUNER: FM/AM radio
Y
BLUETOOTH: Bluetooth connection (the unit as a Bluetooth
• The on-screen operations are not available for Zone2. Use the front display or
web control (p.86) to control Zone2.
• AirPlay is available in Zone2 only when AirPlay playback is ongoing in the main
zone.
DISPLAY
NET: NETWORK sources (press repeatedly to select a desired
BAND
MODE
TUNING
network source)
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
ENHANCER PURE DIRECT
INFO
SLEEP
1
2
3
4
5
6
7
8
9
SLEEP
0
MEMORY
ENT
ENHANCER
• Playing back music stored on media servers (PCs/NAS) (p.72)
• Playing back iTunes/iPhone music with AirPlay (p.79)
AUDIO 1-5: AUDIO 1-5 jacks
USB: USB jack (on the front panel)
RETURN
• Playing back music via Bluetooth (p.67)
• Listening to Internet radio (p.76)
receiver)
ENTER
• Listening to FM/AM radio (p.63)
• Playing back music stored on a USB storage device (p.69)
AV 1-2: AV 1-2 (AUDIO) jacks
PROGRAM MUTE
Start playback on the external device or select a radio
X
• To set the sleep timer (120 min, 90 min, 60 min, 30 min, off), press SLEEP
PHONO: PHONO jacks
repeatedly. The Zone2 output will be disabled after a specified period of time.
Y
• To adjust the Zone2 volume, press VOLUME or MUTE (when using the unit’s
You cannot select Bluetooth, USB and network sources exclusively for each
internal amplifier).
zone. For example, if you select “SERVER” for Zone2 when “USB” is selected for
• To enable the Compressed Music Enhancer function (p.62), press ENHANCER.
the main zone, the input source for the main zone also switches to “SERVER”.
• The Zone2 input automatically switches in conjunction with the input source
selected in the main zone when “Main Zone Sync” is selected as the Zone2
input with the web control (p.86) or AV CONTROLLER (p.7).
• To play back DSD audio in Zone2, select “Main Zone Sync” as the Zone2 input
or use the party mode (p.84).
• Depending on the “Remote PROGRAM Key” setting (p.120), the PROGRAM Key
may be also available in Zone2.
Caution
• To avoid unexpected noise, never play back DTS-CDs in Zone2.
En
83
⬛ Enjoying the same source in multiple
rooms (party mode)
The party mode allows you to play back in Zone2 the same music that is
HDMI
1
2
3
being played back in the main zone. During the party mode, stereo
4
5
playback is automatically selected for all zones. Utilize this function
V-AUX
AUDIO
1
2
3
4
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
when you want to use main zone music as background music for a house
AV
MAIN
ZONE 2
party.
PARTY
SCENE
2
1
3
4
1
Press PARTY.
Each time you press the key, the party mode is turned on or off.
When the party mode is turned on, “PARTY” lights up in the front
PROGRAM MUTE
TOP MENU
VOLUME
POP-UP/MENU
display.
Y
If the party mode does not work on Zone2, set “Party Mode Set” (p.119) in the
ON
SCREEN
OPTION
“Setup” menu to “Enable” (default).
ENTER
RETURN
DISPLAY
BAND
MODE
TUNING
PRESET
SUR. DECODE STRAIGHT
MOVIE
MUSIC
INFO
SLEEP
1
2
3
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
4
En
84
Registering favorite items (shortcut)
You can register up to 40 favorite USB, Bluetooth and network contents
1
2
3
4
5
2
5
1
3
4
2
TUNER
Recall a registered item by selecting the shortcut number.
X
V-AUX
AUDIO
1
• You can also use the “Favorites” feature to register Internet radio stations.
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
• Only the input source will be registered for Bluetooth and AirPlay. Individual
BLUETOOTH
USB
NET
SCENE
2
1
3
PROGRAM MUTE
Recalling a registered item
as shortcuts and access them directly by selecting the shortcut numbers.
HDMI
contents cannot be registered.
Use the Numeric keys to enter a shortcut number (01 to
You can also use PRESET on the front panel to select a shortcut.
Select a desired item and register it to a shortcut number.
VOLUME
Press BLUETOOTH, NET or USB.
40).
Registering an item
4
1
2
LINK MASTER
OUT
2
ECO
1
2
POP-UP/MENU
TOP MENU
ON
SCREEN
OPTION
ENTER
Play back a song or a radio station to be registered.
OUT
DISPLAY
2
ECO
TUNING
• “Empty” appears when a preset number not in use is entered.
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
INFO
SLEEP
1
2
3
4
5
6
7
8
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
Numeric keys
MEMORY
– A USB storage device which contains the registered item is not connected to
this unit.
X
– A PC which contains the registered item is turned off or not connected to the
network.
To change a shortcut number to which the item will be registered, use Numeric
– The registered network content is temporarily unavailable or out of service.
keys to select the shortcut number after step 2.
– The registered item (file) has been deleted or moved to another location.
LINK MASTER
OUT
2
ECO
02:Empty
– A BLUETOOTH connection cannot be established.
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
• When you register music files stored on a USB storage device or a PC, this unit
memorizes the relative position of the music files in the folder. If you have
added or deleted any music files to or from the folder, this unit may not recall
“Empty” (not in use) or item currently registered
3
• The registered item cannot be recalled in the following cases.
Shortcut number (flashes)
PRESET
SUR. DECODE STRAIGHT
MUSIC
FPL
FPR
SL
SW
SR
SBL SB SBR
• “No Presets” appears when no items are registered.
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
01:Empty
BAND
MODE
MOVIE
VOL. MUTE VIRTUAL
Y
Press MEMORY.
LINK MASTER
RETURN
01:USB
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
the music file correctly. In such cases, register the items again.
• The registered content (songs and Internet radio stations) can be displayed as
To confirm the registration, press MEMORY.
a list and easily recalled by using MusicCast CONTROLLER (p.54) on your
mobile device.
En
85
Controlling the unit from a web browser (web control)
X
You can control the unit with the web control screen displayed in a web browser.
• You can check the IP address of the unit in “Network” (p.124) in the “Information” menu.
Web browser
• You can bookmark the unit’s IP address in the browser or create a shortcut link (p.88) to access the web control
screen quickly in the future. However, if you are using a DHCP server, the IP address of the unit may change each
time the unit is turned on.
Web control
Web control
• If you have enabled the MAC address filter (p.116), you need to specify the MAC address of your PC to allow the
PC to access the unit. For information on how to check the MAC address of your PC, refer to its instruction
(wired or wireless)
PC
manual.
(wired or wireless)
Router
The unit
• By using the application for smartphone/tablet “AV CONTROLLER”, you can control the unit from an iPhone,
Y
iPad, iPod touch or Android devices (p.7).
• To use this function, the unit and your PC must be connected to the same router.
• Some security software installed on your PC may block the access of the unit to your PC. In these cases,
configure the security software appropriately.
• To display the web control screen or turn on the unit from the web control when the unit is in standby mode,
set “Network Standby” (p.88) to “On”.
• We recommend using one of the following web browsers.
– Internet Explorer 11.x
– Safari 9.x
1
2
Start the web browser.
Enter the IP address of the unit in the address bar of the web browser.
(Example)
En
86
Top menu screen
Control screen
c
a
e
a
f
b
c
d
d
e
g
b
f
a PLAY INFO
a CONTROL
Selects an input source or controls playback for the selected zone.
Moves to the control screen for the selected zone.
b TOP MENU
b STATUS
Moves to the top menu screen.
Turns on/off the power for each zone or displays the input source and volume set for each zone.
c SCENE
c SETTINGS
Selects a scene for the selected zone.
Moves to the settings screen.
d POWER
d PARTY MODE
Turns on/off the power for the selected zone.
Turns on/off the party mode (p.84).
e VOLUME
e SYSTEM POWER
Adjusts the volume or mutes the audio output for the selected zone. You can also select the increments
used for volume adjustment.
Turns on/off the power for all zones.
f MAIN VOLUME
f RELOAD
Adjusts the volume or mutes the audio output for the main zone. You can also select the increments used
for volume adjustment.
Reloads the current status of the unit.
Y
g RELOAD
Multi-zone volume adjustment is not available when an external amplifier is used.
Reloads the current status of the unit.
En
87
Settings screen
Google Analytics
Displays an explanation of data collection by Google Analytics. Data collection can be enabled or
disabled at any time.
b BACK
Moves to the top menu screen.
a
c RELOAD
Reloads the current status of the unit.
Note
• If the network settings are changed, you may need to restart the browser or regain access to the unit.
b
• When using the MAC address filter, make sure you specify the MAC addresses of your network devices
correctly. Otherwise, the unit will be inaccessible from your network devices such as PCs and other
external devices.
c
a Rename
• Do not operate the unit during the recovery process, as this may result in the incorrect recovery of the
settings. When the recovery finishes, click “OK” to set the unit to standby mode.
Edits the network name (the unit’s name on the network) (p.116) or the name of each zone (p.118). Click
“APPLY” to apply the changes to the unit.
• The backup does not contain user information (such as user account and password) or unit-specific
information (such as MAC address and IP address).
Network
• Some characters entered with a PC may not appear correctly on the unit.
Selects the network connection method (p.115) or configures the network parameters (such as IP
address) (p.115). Click “APPLY” to apply the changes to the unit.
AirPlay Password
Sets the password to restrict access to the unit via AirPlay (p.79). Click “APPLY” to apply the changes to
the unit.
MAC Filter
Sets the MAC address filter (p.116) to limit access to the unit from the network devices. Click “APPLY” to
apply the changes to the unit.
Auto Reload
Enables/disables automatic reloading. When “Auto Reload” is “On” (enabled), the web control screen
reloads the status of the unit every 5 seconds.
Network Standby
Enables/disables the network standby function (p.115).
Backup/Recovery
Creates a backup of the unit’s settings on the PC or restores the settings from the backup.
Firmware
Updates the firmware of the unit by using the firmware you have downloaded on the PC.
Follow the on-screen instructions to start the firmware update.
Create Link
Creates a shortcut link to the desired control screen.
Tips
Displays tips for use of the web control.
Licenses
Displays the licenses of the software used in the unit.
En
88
Viewing the current status
You can view the current status (input or DSP program currently
selected) on the front panel display or TV.
HDMI
1
2
3
5
V-AUX
AUDIO
1
2
5
1
3
4
2
TUNER
Switching information on the front display
AV
BLUETOOTH
MAIN
NET
PHONO
PARTY
HDMI OUT
USB
ZONE 2
1
3
OUT
2
VOL. MUTE VIRTUAL
Audio Decoder
VOLUME
FPL
FPR
SL
SW
SR
SBL SB SBR
information appears.
OUT
DISPLAY
2
ECO
PRESET
MUSIC
SLEEP
1
2
5
6
9
0
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
Information
SUR. DECODE STRAIGHT
INFO
Viewing the status information on the TV
†‡ Dsur
BAND
MODE
MOVIE
ENHANCER PURE DIRECT
INFO
1
X
Available items vary depending on the selected input source. The displayed item can
7
8
also be applied separately to each input source.
MEMORY
ENT
Currently input
source
Press DISPLAY.
The following information is displayed on the TV.
4
3
DSP Program (sound mode name), Audio Decoder
(decoder name*), IP Address, Ethernet MAC, Wi-Fi MAC
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
DISPLAY
TUNING
MusicCast Link
About 3 seconds after a display item is selected, its corresponding
OPTION
ENTER
RETURN
Song (song title), Album (album name), Station (station
name), DSP Program (sound mode name), Audio
Decoder (decoder name*), IP Address, Ethernet MAC,
Wi-Fi MAC
* The name of the audio decoder currently activated is displayed. If no audio decoder
is activated, “Decoder Off” appears.
Item name
POP-UP/MENU
ON
SCREEN
NET RADIO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
LINK MASTER
TOP MENU
AirPlay
4
ECO
PROGRAM MUTE
Item
Song (song title), Artist (artist name), Album (album
name), DSP Program (sound mode name), Audio
Decoder (decoder name*), IP Address, Ethernet MAC,
Wi-Fi MAC
SERVER
Press INFO repeatedly to select between the various
display items.
SCENE
2
1
Currently input
source
4
Input source/
Party mode
status
Compressed Music
Enhancer status
Volume/
YPAO Volume
status
CINEMA DSP status
Sound mode
Item
HDMI 1-5
VIDEO AUX
AV 1-2
Input (input source name), DSP Program (sound mode
name), Audio Decoder (decoder name*)
AUDIO 1-5
PHONO
Frequency (frequency), DSP Program (sound mode
name), Audio Decoder (decoder name*)
TUNER
Bluetooth
USB
* (U.K. and Europe models only)
Radio Data System data is also available when the unit is
tuned into a Radio Data System broadcasting station
(p.65).
Song (song title), Artist (artist name), Album (album
name), DSP Program (sound mode name), Audio
Decoder (decoder name*)
En
89
Audio format/
Decoder
2
To close the information display, press DISPLAY.
Configuring playback settings for different playback sources (Option menu)
You can configure separate playback settings for different playback sources. This menu is
Item
available on the front panel (or on the TV screen), allowing you to easily configure settings
during playback.
1
Press OPTION.
YPAO Volume
(YPAO Volume)
Front display
LINK MASTER
OUT
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
Tone Control
Page
91
YPAO Volume
(YPAO Vol.)
Enables/disables YPAO Volume.
91
Adaptive DRC
(A.DRC)
Sets whether the dynamic range (from maximum to
minimum) is automatically adjusted when the volume is
adjusted.
91
Dialogue Level
(Dialog Lvl)
Adjusts the volume of dialogue sounds.
91
DTS Dialogue
Control
(DTS Dialog)
Adjusts the volume of dialogue sounds for DTS:X
contents.
91
Dialogue Lift
(Dialog Lift)
Adjusts the perceived height of dialogue sounds.
92
Adjusts the delay between video and audio output.
92
VOL. MUTE VIRTUAL
FPL
FPR
SL
SW
SR
SBL SB SBR
TV screen
Dialogue
(Dialog)
Lipsync Adjustment
(Lipsync Adj.)
2
Function
Adjusts the level of high-frequency range and
low-frequency range individually.
Tone Control
(Tone Control)
Subwoofer Trim
Fine-adjusts the subwoofer volume.
(SW.Trim)
92
Extra Bass
(Extra Bass)
Enables/disables Extra Bass.
92
Enhancer
(Enhancer)
Enables/disables Compressed Music Enhancer.
92
Video Processing
(Video Process.)
Enables/disables the video signal processing settings
configured in the “Setup” menu.
93
Input Trim
(In.Trim)
Corrects volume differences between input sources.
93
Video Out
(V.Out)
Selects a video to be output with the selected audio
source.
93
93
Subwoofer/Bass
(Subwoofer/Bass)
Use the cursor keys to select an item and press ENTER.
X
To return to the previous screen during menu operations, press RETURN.
3
4
Use the cursor keys (e/r) to select a setting.
Input Settings
(Input Settings)
To exit from the menu, press OPTION.
Option menu items
FM Mode
(FM Mode)
Switches between stereo and monaural for FM radio
reception.
X
Traffic Program
(TrafficProgram)
(U.K. and Europe models only)
Shuffle
(Shuffle)
Configures the shuffle setting for the USB storage device
(p.71) or media server (p.75).
⏤
Repeat
(Repeat)
Configures the repeat setting for the USB storage device
(p.71) or media server (p.75).
⏤
• Available items vary depending on the selected input source.
• Text in parentheses denotes indicators on the front display.
• Default settings are underlined.
En
90
Automatically searches for a traffic information station.
65
⬛ Tone Control (Tone Control)
Adaptive DRC (A.DRC)
Adjusts the level of high-frequency range (Treble) and low-frequency range (Bass) individually.
Sets whether the dynamic range (from maximum to minimum) is automatically adjusted when
the volume level is adjusted. When it is set to “On”, it is useful for listening to playback at a low
Choices
Treble (Treble), Bass (Bass)
volume at night.
Settings
Setting range
-6.0 dB to 0.0 dB to +6.0 dB, *0.5 dB increments
Y
Off (Off)
The dynamic range is not automatically adjusted.
On (On)
Automatically adjusts the dynamic range when YPAO Volume is enabled.
• When both “Treble” and “Bass” are 0.0 dB, “Bypass” appears.
If “On” is selected, the dynamic range becomes narrow at a low volume and wide at a high
• If you set an extreme value, sounds may not match those from other channels.
volume.
Adjusting with the front panel controls
a Press TONE CONTROL to select “Treble” or “Bass”.
b Press PROGRAM to make an adjustment.
⬛ YPAO Volume (YPAO Volume)
On
Off
Volume: high
Output level
Output level
Volume: low
On
Input level
Off
Input level
Enables/disables YPAO Volume or Adaptive DRC.
⬛ Dialogue (Dialog)
YPAO Volume (YPAO Vol.)
Adjusts the volume or perceive height of dialogue sounds.
Enables/disables YPAO Volume. When YPAO Volume is enabled, the high- and low-frequency
levels are automatically adjusted according to the volume so that you can enjoy natural
Dialogue Level (Dialog Lvl)
sounds even at low volume.
Adjusts the volume of dialogue sounds. If dialogue sounds cannot be heard clearly, you can
Settings
turn up its volume by increasing this setting.
Off (Off)
Disables YPAO Volume.
On (On)
Enables YPAO Volume.
Setting range
0 to 3
X
X
This setting is not available when DTS:X content is played back, or when the Dolby Surround or Neural:X decoder
• YPAO Volume works effectively after the measurement results of “Auto Setup” have been already saved (p.40).
is working.
• We recommend enabling both YPAO Volume and Adaptive DRC when you are listening at lower volumes or at
night.
DTS Dialogue Control (DTS Dialog)
Adjusts the volume of dialogue sounds for DTS:X contents.
Setting range
0 to 6
X
This setting is available only when DTS:X content which supports the DTS Dialogue Control feature is played back.
En
91
⬛ Subwoofer/Bass (Subwoofer/Bass)
Dialogue Lift (Dialog Lift)
Adjust the subwoofer volume or bass sound.
Adjusts the perceived height of dialogue sounds. If the dialogue sounds as if it is coming from
below the TV screen, you can raise its perceived height by increasing this setting.
Subwoofer Trim (SW.Trim)
X
This setting is available only when one of the following conditions is met.
Fine-adjusts the subwoofer volume.
– One of the sound programs (except for 2ch Stereo and 7ch Stereo) is selected when presence speakers are used.
Setting range
-6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments)
– Virtual Presence Speaker (VPS) (p.58) is working.
(You may hear dialogue sounds from the surround speakers depending on the listening position.)
Extra Bass (Extra Bass)
Setting range
0 to 5 (The bigger the value the higher the position)
Enables/disables Extra Bass. When Extra Bass is enabled, you can enjoy enhanced bass sounds,
regardless of the size of the front speakers and the presence or absence of the subwoofer.
Settings
Ideal position
Off (Off)
Disables Extra Bass.
On (On)
Enables Extra Bass.
⬛ Enhancer (Enhancer)
Enables/disables Compressed Music Enhancer (p.62).
⬛ Lipsync Adjustment (Lipsync Adj.)
X
Adjusts the delay between video and audio output.
• This setting is applied separately to each input source.
Setting range
0 ms to 500 ms (1 ms increments)
• You can also use ENHANCER on the remote control to enable/disable Compressed Music Enhancer (p.62).
Settings
X
This setting is available only when “Delay Enable” (p.110) in the “Setup” menu is set to “Enable” (default).
En
92
Off (Off)
Disables Compressed Music Enhancer.
On (On)
Enables Compressed Music Enhancer.
⬛ Video Processing (Video Process.)
⬛ FM Mode (FM Mode)
Enables/disables the video signal processing (resolution and aspect ratio) settings configured
Switches between stereo and monaural for FM radio reception.
in “Processing” (p.112) in the “Setup” menu.
Settings
Settings
Direct (Direct)
Disables the video signal processing.
Processing (Processing)
Enables the video signal processing.
⬛ Input Settings (Input Settings)
Configures the input settings.
X
This setting is applied separately to each input source.
Input Trim (In.Trim)
Corrects volume differences between input sources. If you are bothered by volume differences
when switching between input sources, use this function to correct it.
Setting range
-6.0 dB to 0.0 dB to +6.0 dB (0.5 dB increments)
Video Out (V.Out)
Selects a video to be output with the selected audio source.
Settings
Off (Off)
Does not output video.
HDMI 1-5 (HDMI1-5), AV 1-2
(AV1-2), VIDEO AUX (V-AUX)
Outputs video input through the corresponding video input jacks.
En
93
Stereo (Stereo)
Receives FM radio in stereo sounds.
Mono (Mono)
Receives FM radio in monaural sounds.
CONFIGURATIONS
Configuring input sources (Input menu)
You can change the input source settings using the TV screen.
1
2
4
Use the cursor keys (q/w) to select an item and press ENTER.
Press ON SCREEN.
Use the cursor keys to select “Input” and press ENTER.
X
To return to the previous screen during menu operations, press RETURN.
3
5
6
Use the cursor keys (e/r) to select an input source to be configured and
press the cursor key (q).
Use the cursor keys to select a setting and press ENTER.
To exit from the menu, press ON SCREEN.
Input menu items
X
• Available items vary depending on the selected input source.
• Default settings are underlined.
Item
The input source of the unit also changes.
X
You can still switch the input source by using cursor keys (e/r) after Step 3.
En
94
Function
Page
Rename/Icon Select
Changes the input source name and icon.
95
Audio In
Combines the video jack of the selected input source with an
audio jack of others.
95
Decoder Mode
Sets the format of digital audio playback to DTS.
96
Volume Interlock
Enables/disables volume controls from iTunes/iPhone via AirPlay.
96
DMC Control
Selects whether to allow a DLNA-compatible Digital Media
Controller (DMC) to control playback.
96
⬛ Rename/Icon Select
⬛ Audio In
Changes the input source name and icon displayed on the front display or TV screen.
Combines the video jack of the selected input source with an audio jack of others. For example,
The following input sources can not be renamed or have their icons changed:
use this function in the following cases.
AirPlay
• Connecting a playback device that supports HDMI video output, but not HDMI audio output
⬛ Setup procedure
• Connecting a playback device that has component video jacks and analog stereo jacks (such
1
as game consoles)
Use the cursor keys (e/r) to select “Auto” or “Manual” and press the cursor key (w).
Input sources
HDMI 1-5, AV 1-2
If you select “Auto”, the unit creates a name automatically according to the connected device.
Proceed to Step 3.
(To input audio through a digital optical jack)
X
Select “AUDIO 1” or “AUDIO 2” and connect the device to the unit’s corresponding audio jacks
This step is available only when “HDMI1-5”, “AV 1”, “VIDEO AUX” or “AUDIO 1-3” is selected.
2
Use the cursor keys (e/r) to select an icon and press the cursor key (w).
3
Press ENTER to enter the name edit screen.
4
Use the cursor keys and ENTER to rename and select “ENTER” to confirm the entry.
with a digital optical cable.
(To input audio through a digital coaxial jack)
Select “AUDIO 3” or “AV 1” and connect the device to the unit’s corresponding audio jacks with
a digital coaxial cable.
(To input audio through analog audio jacks)
Select “AUDIO 4”, “AUDIO 5” or “AV 2”, and connect the device to the unit’s corresponding
audio jacks with a stereo pin cable.
X
To clear the entry, select “CLEAR”.
5
Use the cursor keys to select “OK” and press ENTER.
X
To restore the default setting, select “RESET”.
6
To exit from the menu, press ON SCREEN.
En
95
⬛ Decoder Mode
Configuring the SCENE function (Scene menu)
Sets the format of digital audio playback to “DTS”.
You can change the settings of the SCENE function (p.56) using the TV screen.
For example, if the unit does not detect DTS audio and outputs noise, set “Decoder Mode” to
“DTS”.
Input sources
HDMI 1-5, VIDEO AUX, AV 1, AUDIO 1-3
Settings
Auto
Automatically selects an audio format to match the input audio signal.
DTS
Selects DTS only. (Other audio signals are not reproduced.)
1
2
Press ON SCREEN.
3
Use the cursor keys (e/r) to select a scene to be configured and press the
Use the cursor keys to select “Scene” and press ENTER.
⬛ Volume Interlock
Enables/disables volume controls from iTunes/iPhone via AirPlay.
Input sources
AirPlay
Settings
cursor key (q).
Off
Disables volume controls from iTunes/iPhone.
Limited
Enables volume controls from iTunes/iPhone within the limited range
(-80 dB to -20 dB and mute).
Full
Enables volume controls from iTunes/iPhone in the full range
(-80 dB to +16.5 dB and mute).
⬛ DMC Control
Selects whether to allow DLNA-compatible Digital Media Controller (DMC) to control playback.
X
Input source
SERVER
You can still switch the scene by using cursor keys (e/r) after Step 3.
Settings
Disable
Does not allow DMCs to control playback.
Enable
Allows DMCs to control playback.
X
A Digital Media Controller (DMC) is a device that can control other network devices through the network. When
this function is enabled, you can control playback of the unit from DMCs (such as Windows Media Player 12) on
the same network.
En
96
4
⬛ Load
Use the cursor keys (q/w) to select an item and press ENTER.
Loads the settings registered for the selected scene.
Select “DETAIL” to configure the SCENE link playback setting or view the scene assignments.
Device Control
Recalls a selected scene and starts its playback on an external device connected to the unit via
HDMI. (SCENE link playback)
Settings
5
6
Off
Disables the SCENE link playback function.
HDMI Control
Enables SCENE link playback using HDMI Control signals. Select this if an HDMI
Control-compatible device (such as a BD/DVD player) is connected to the unit via
HDMI. It also turns on the TV if it supports HDMI Control.
Use the cursor keys and ENTER to change the setting.
To exit from the menu, press ON SCREEN.
Default
SCENE1, SCENE2: HDMI Control
Scene menu items
Item
SCENE3, SCENE4: Off
Function
Y
Page
Save
Registers the current settings in the selected scene.
97
Load
Loads the settings registered for the selected scene. You can also
configure the SCENE link playback setting or view the scene
assignments.
97
Rename/Icon Select
Changes the scene name and icon.
99
Reset
Restores the default settings for the selected scene.
99
To control playback of an HDMI Control-compatible device by SCENE link playback, you need to set “HDMI
Control” in the “Setup” menu to “On” and perform the HDMI Control link setup (p.145).
⬛ Save
Registers the unit’s current settings (input source (including the selected radio station or
content when it is assigned), sound program/surround decoder, Compressed Music Enhancer
on/off) in the selected scene.
X
• If you have changed the input assignment for a scene, you also need to change the external device assigned to
the corresponding SCENE key (p.56).
• When the input source is NET, USB, Bluetooth or TUNER, the selected radio station or content is assigned.
En
97
⬛ Playing a radio station or content included as the scene assignments automatically when
pressing SCENE
Detail
Selects items to be included as the scene assignments. You can also view the settings currently
assigned to the selected scene.
To include items as the scene assignments, use the cursor keys to select an item and press
ENTER to check the box (or uncheck the box to exclude).
For example, if you often adjust the volume while watching TV but listen to radio with low
volume at night, exclude “Volume” from the assignments for SCENE2 and include “Volume” in
the assignments for SCENE4.
X
1
2
Use the cursor keys (e/r) to select a scene to be configured and press the cursor key (q).
3
Use the cursor keys (e/r) to select “DETAIL” and press ENTER.
4
Use the cursor keys (q/w) to select “Input” and press the cursor key (r).
5
Use the cursor keys to select “Playback” or “Listening” and press ENTER.
Use the cursor keys (q/w) to select “Load” and press ENTER.
The scene assignments can include radio stations, or the content on a selected USB storage device, Bluetooth
When “NET”, “USB” or “Bluetooth” is selected only, “Playback” is available.
device, and network device.
When “TUNER” is selected only, “Listening” is available.
Check or uncheck
Choices
Input (p.55), Music Content*, Playback*, Station**, Listening**
Input
* When “NET”, “USB” or “Bluetooth” is selected only.
** When “TUNER” is selected only.
HDMI Output
HDMI Output (p.55)
Mode
DSP Program (p.57), Enhancer (p.62)
Sound
Tone Control (p.91), YPAO Volume (p.91), Adaptive DRC (p.91), Extra Bass (p.92)
Surround
CINEMA DSP 3D Mode (p.111), Dialogue Lift (p.92), Dialogue Level (p.91),
Subwoofer Trim (p.92)
Video
Video Mode (p.112)
Volume
Master Volume (p.55)
Lipsync
Lipsync (p.110), Delay (p.111)
Speaker Setup
PEQ Select (p.109)
Default
Input, HDMI Output, Mode: selected
Sound, Surround, Video, Volume, Lipsync, Speaker Setup: not selected
En
98
6
Use the cursor keys to select a setting and press ENTER.
7
To exit from the menu, press ON SCREEN.
⬛ Rename/Icon Select
Changes the scene name and icon displayed on the front display or TV screen.
⬛ Setup procedure
1
Use the cursor keys (e/r) to select an icon and press the cursor key (w).
2
3
Press ENTER to enter the name edit screen.
Use the cursor keys and ENTER to rename and select “ENTER” to confirm the entry.
X
To clear the entry, select “CLEAR”.
4
Use the cursor keys to select “OK” and press ENTER.
X
To restore the default setting, select “RESET”.
5
To exit from the menu, press ON SCREEN.
⬛ Reset
Restores the default settings (p.56) for the selected scene.
En
99
Configuring sound programs/surround decoders (DSP Program menu)
You can change the settings of the sound programs and surround decoders using the TV
4
screen.
1
2
Use the cursor keys (q/w) to select an item and press ENTER.
Press ON SCREEN.
Use the cursor keys to select “DSP Program” and press ENTER.
X
• To return to the previous screen during menu operations, press RETURN.
• To restore the default settings for the selected sound program, select “Reset”.
3
5
6
Use the cursor keys (e/r) to select a sound program to be configured and
press the cursor key (q).
X
You can still switch the sound program by using cursor keys (e/r) after Step 3.
En
100
Use the cursor keys to select a setting and press ENTER.
To exit from the menu, press ON SCREEN.
DSP Program menu items
Item
Function
Settings
1.0 s to 5.0 s
X
Reverb Time
Adjust the decay time of the rear
reverberant sound.
Reverb Delay
0 ms to 250 ms
Adjusts the delay between the direct
Higher to enhance the delay
sound and reverberant sound generation.
effect, and lower to reduce it.
Reverb Level
Adjusts the volume of the reverberant
sound.
• Available items vary depending on the selected sound program or surround decoder.
• Default settings are underlined.
⬛ Settings for sound programs
Item
Decode Type
Function
Selects a surround decoder to be used in
combination with the selected sound
program.
0% to 100%
Settings
Auto, bDsur*, Neural:X, Neo:6
Cinema, Neo:6 Music*
(* Available only when
“SURROUND DECODER” is
selected)
Adjusts the sound field effect level.
Initial Delay
Adjusts the delay between the direct
sound and presence sound field
generation.
Surround Initial Delay
Adjusts the delay between the direct
sound and surround sound field
generation.
Surround Back Initial
Delay
Adjusts the delay between the direct
sound and surround back sound field
generation.
Room Size
Adjusts the broadening effect of the
presence sound field.
Surround Room Size
Adjusts the broadening effect of the
surround sound field.
Surround Back Room Size
Adjusts the broadening effect of the
surround back sound field.
Liveness
Adjusts the loss of the presence sound
field.
Surround Liveness
Adjusts the loss of the surround sound
field.
Surround Back Liveness
Adjusts the loss of the surround back
sound field.
Higher to strengthen the
reverberant sound, and lower
to weaken it.
The following items are available when you select “7ch Stereo”.
Sound program
-6 dB to 0 dB to +3 dB
DSP Level
Higher to enrich the
reverberant sound and lower to
have clear sound.
Item
Level
Higher to enhance the sound
field effect, and lower to reduce
it.
Function
Adjusts the entire volume.
Settings
-5 to 0 to +5
-5 to 0 to +5
1 ms to 99 ms
Front / Rear Balance
Adjusts the front and rear
volume balance.
Left / Right Balance
Adjusts the left and right
volume balance.
Higher to enhance the delay
effect, and lower to reduce it.
Higher to enhance the front
side, and lower to enhance the
rear side.
-5 to 0 to +5
1 ms to 49 ms
7ch Stereo
Higher to enhance the delay
effect, and lower to reduce it.
Higher to enhance the right
side, and lower to enhance the
left side.
0 to 5 to 10
Height Balance
Adjust the height volume
balance using the presence
speakers.
Monaural Mix
Enables/disables monaural
sound output.
0.1 to 2.0
Higher to enhance the
broadening effect, and lower to
reduce it.
Higher to enhance the upside,
and lower to enhance the
downside. (The presence
speakers do not produce
sounds when “Height
Balance” is set to “0”.)
Off, On
X
Available items in “7ch Stereo” vary depending on the speaker system being used.
0 to 10
Higher to enhance the
reflectivity, and lower to reduce
it.
En
101
⬛ Settings for decoders
The following items are available when you set “Decode Type” of “SURROUND DECODER” to
“bDsur” or “Neo:6 Music”.
Decode Type
bDsur
Neo:6 Music
Item
Function
Settings
Center Spread
Selects whether to spread
the center channel signals
to left and right when
2-channel source is
played.
Select “On” to spread center channel
signals to left and right if you feel the
center sound is too strong when
2-channel source is played.
Center Image
Adjusts the center
orientation level
(broadening effect) of the
front sound field.
Off, On
0.0 to 0.3 to 1.0
Higher to strengthen the center
orientation level (less broadening
effect) and lower to weaken (more
broadening effect).
En
102
Configuring various functions (Setup menu)
You can configure the unit’s various function with the menu displayed on the TV screen.
4
X
Use the cursor keys (q/w) to select an item and press ENTER.
• Operations with TV screen are available only when your TV is connected to the unit via HDMI. If not, carry out
operations while viewing the front display.
• If new firmware is available, the message screen appears. For details, see “Updating the unit’s firmware via the
network” (p.129).
• If new firmware is available, the envelope icon (p) appears in the screen.
1
2
Press ON SCREEN.
X
Use the cursor keys to select “Setup” and press ENTER.
To return to the previous screen during menu operations, press RETURN.
5
6
3
Use the cursor keys (e/r) to select a menu.
En
103
Use the cursor keys to select a setting and press ENTER.
To exit from the menu, press ON SCREEN.
Setup menu items
Menu
Item
Function
Auto Setup
Automatically optimizes the speaker settings (YPAO).
40
Selects a speaker system.
107
Front
Selects the size of the front speakers.
107
Center
Selects whether or not a center speaker is connected and its size.
107
Surround
Selects whether or not surround speakers are connected and their size.
108
Surround Back
Selects whether or not surround back speakers are connected and their size.
108
Front Presence
Selects whether or not presence speakers are connected and their size.
108
Subwoofer
Selects whether or not a subwoofer is connected and its phase.
108
Layout
Selects the layouts of the surround speakers and front presence speakers.
108
Power Amp Assign
Configuration
Speaker
Page
Manual Setup
Lipsync
Distance
Sets the distance between each speaker and listening position.
109
Level
Adjusts the volume of each speaker.
109
Parametric EQ
Adjusts the tone with an equalizer.
109
Test Tone
Enables/disables the test tone output.
110
Delay Enable
Enables/disables the Lipsync adjustment for each input source.
110
Auto/Manual Select
Selects the method to adjust the delay between video and audio output.
110
Adjustment
Adjusts the delay between video and audio output manually.
111
Dynamic Range
Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS signals) playback.
111
Max Volume
Sets the limit value of the volumes.
111
Initial Volume
Sets the initial volume for when this receiver is turned on.
111
Adaptive DSP Level
Selects whether to automatically adjust the CINEMA DSP effect level when the volume is adjusted.
111
CINEMA DSP 3D Mode
Enables/disables CINEMA DSP 3D.
111
Virtual Surround Back Speaker
Selects whether to create Virtual Surround Back Speaker (VSBS) using the surround speakers.
111
Object Decode Mode
Enables/disables playback of object-based audio signals such as Dolby Atmos or DTS:X contents.
112
Video Mode
Enables/disables the video signal processing (resolution and aspect ratio).
112
HDMI Control
Enables/disables HDMI Control. You can also configure the relevant settings (such as ARC and TV audio input).
113
Audio Output
Selects a device to output audio.
114
Standby Through
Select whether to output videos/audio (input through HDMI jacks) to the TV when the unit is in standby mode.
114
Sound
Video
HDMI
En
104
Menu
Network
Item
Function
Page
Network Connection
Selects the network connection method.
115
IP Address
Configures the network parameters (such as IP address).
115
Network Standby
Selects whether to enable/disable the function that turns on the unit from other network devices.
115
MAC Address Filter
Sets the MAC address filter to limit access to the unit from other network devices.
116
Network Name
Edits the network name (the unit’s name on the network) displayed on other network devices.
116
MusicCast Link Power Interlock
Selects whether turning on the power of the master device of the MusicCast network (this unit) also turns on the power of
other devices of the network.
116
Bluetooth
Enables/disables the Bluetooth functions.
117
Disconnect
Terminates the Bluetooth connection between the Bluetooth device (such as smartphones) and the unit.
67
Bluetooth Standby
Selects whether to enable/disable the function that turns on the unit from Bluetooth devices (Bluetooth standby).
117
Transmitter
Enables/disables the Bluetooth audio transmitter function.
117
Audio Receive
Bluetooth
Audio Send
Device Search
Searches available Bluetooth devices (speakers/headphones) when the unit is used as a Bluetooth audio transmitter.
68
Zone Rename
Changes the zone name (for main zone) displayed on the TV screen.
118
Volume
Enables/disables volume adjustments for Zone2 output.
118
Max Volume
Sets the Zone2 limit value of the volumes.
118
Initial Volume
Sets the Zone2 initial volume for when the unit is turned on.
118
Audio Delay
Adjusts the audio output timing for Zone2.
118
Mono
Switches between stereo and monaural for Zone2 output.
119
Enhancer
Enables/disables Compressed Music Enhancer for Zone2 output.
119
Tone Control
Adjusts the level of high-frequency range and low-frequency range for Zone2 output.
119
Extra Bass
Enables/disables Extra Bass for Zone2 output.
119
Balance
Adjusts the volume balance for Zone2 output.
119
Zone Rename
Changes the zone name (for Zone2) displayed on the TV screen.
119
Party Mode Set
Enables/disables switching to the party mode.
119
Remote PROGRAM Key
Select the function that is assigned to the PROGRAM key.
120
Dimmer (Front Display)
Adjusts the brightness of the front display.
120
Short Message
Selects whether to display short messages on the TV screen when the unit is operated.
120
Wallpaper
Selects the image to be used as wallpaper on the TV.
120
Trigger Mode
Specifies the condition for the TRIGGER OUT jack to function.
121
Target Zone
Specifies the zone with which the TRIGGER OUT jack functions are synchronized.
121
Prevents accidental changes to the settings.
121
Main Zone Set
Multi Zone
Zone2 Set
Display Set
Function
Trigger Output
Memory Guard
En
105
Menu
Item
Function
Page
Auto Power Standby
Sets the amount of time for the auto-standby function.
122
ECO Mode
Enables/disables the eco mode (power saving mode).
122
Select an on-screen menu language.
123
ECO
Language
En
106
⬛ Configuration
Speaker (Manual Setup)
Configures the output characteristics of the speakers.
Configures the speaker settings manually.
X
X
When you configure the speaker size, select “Large” if the woofer diameter of your speaker is 16 cm (6-1/4”) or
Default settings are underlined.
larger or “Small” if it is smaller than 16 cm (6-1/4”).
Front
Selects the size of the front speakers.
Settings
Large
Select this option for large speakers.
The front speakers will produce all of the front channel frequency components.
Select this option for small speakers.
Small
⬛ Power Amp Assign
Selects a speaker system.
The subwoofer will produce front channel low-frequency components lower than
the specified crossover frequency (default: 80 Hz).
X
In addition to the 5.1- or 7.1-channel speaker system, various speaker configurations are
“Front” is automatically set to “Large” when “Subwoofer” is set to “None”.
possible using the presence speakers, Zone2 speakers, or bi-amp connection.
Center
Settings
Selects whether or not a center speaker is connected and its size.
Basic
Select this option when you use a normal speaker system (not using Zone2
speakers or a bi-amp connection).
7.1 +1Zone
Select this option when you use Zone2 speakers in addition to the 7.1 system in
the main zone (p.24).
5.1.2 +1Zone
5.1 BI-Amp
Settings
Large
Select this option when you use Zone2 speakers in addition to the 5.1.2 system in
the main zone (p.25).
The center speaker will produce all of the center channel frequency components.
Select this option for small speakers.
Small
Select this option when you connect speakers that support bi-amp connections
(p.25).
None
En
Select this option for large speakers.
107
The subwoofer or front speakers will produce center channel low-frequency
components lower than the specified crossover frequency (default: 80 Hz).
Select this option when no center speaker is connected.
The front speakers will produce center channel audio.
Surround
Front Presence
Selects whether or not surround speakers are connected and their sizes.
Selects whether or not front presence speakers are connected and their size.
Settings
Settings
Large
Select this option for large speakers.
Large
Select this option for large speakers.
The surround speakers will produce all of the surround channel frequency
components.
Small
Select this option for small speakers.
None
Select this option when no front presence speakers are connected.
Select this option for small speakers.
Small
None
The subwoofer or front speakers will produce surround channel low-frequency
components lower than the specified crossover frequency (default: 80 Hz).
Subwoofer
Select this option when no surround speakers are connected.
Selects whether or not a subwoofer is connected and its phase.
The front speakers will produce surround channel audio. Virtual CINEMA DSP
works when you select a sound program.
Settings
Surround Back
Normal
Select this option when a subwoofer is connected (phase not reversed). The
subwoofer will produce LFE (low-frequency effect) channel audio and
low-frequency components from other channels.
Reverse
Select this option when a subwoofer is connected (phase reversed). The
subwoofer will produce LFE (low-frequency effect) channel audio and
low-frequency components from other channels.
Use
Selects whether or not surround back speakers are connected and their sizes.
Settings
Select this option when one large speaker is connected.
Large x1
The surround back speaker will produce all of the surround back channel
frequency components.
None
Select this option when two large speakers are connected.
Large x2
X
The surround back speakers will produce all of the surround back channel
frequency components.
When the bass sound is lacking or unclear, switch the subwoofer phase.
Select this option when one small speaker is connected.
Small x1
Layout
The subwoofer or front speakers will produce surround back channel
low-frequency components lower than the specified crossover frequency
(default: 80 Hz).
Selects the layouts of the surround speakers and front presence speakers.
Select this option when two small speakers are connected.
Small x2
None
Select this option when no subwoofer is connected. The front speakers will
produce LFE (low-frequency effect) channel audio and low-frequency
components from other channels.
Surround
The subwoofer or front speakers will produce surround back channel
low-frequency components lower than the specified crossover frequency
(default: 80 Hz).
Selects a surround speaker layout when surround speakers are used.
Settings
Select this option when no surround back speakers are connected.
The surround speakers will produce surround back channel audio.
X
Rear
Select this option when surround speakers are placed on the rear side of the
room.
Front
Select this option when surround speakers are placed on the front side of the
room. Virtual CINEMA FRONT (p.60) works in this case.
This setting is not available when “Surround” is set to “None”, or when “Layout (Surround)” is set to “Front”.
X
This setting is not available when “Configuration (Surround)” is set to “None”.
En
108
Front Presence
⬛ Parametric EQ
Selects a front presence layout when front presence speakers are used. This setting facilitates
Adjusts the tone with an equalizer.
the optimization of the sound field effect.
Settings
Settings
Front Height
Select this option when front presence speakers are installed on the front side
wall.
Overhead
Select this option when front presence speakers are installed to the ceiling.
Dolby Enabled SP
Manual
Select this option when using the Dolby Enabled speakers as the front presence
speakers.
X
• This setting is not available when “Configuration (Front Presence)” is set to “None”.
Select this option when you want to adjust the equalizer manually.
For details, see “Manual equalizer adjustment”.
YPAO:Flat
Adjusts individual speakers to achieve the same characteristics.
YPAO:Front
Adjusts individual speakers to achieve the same characteristics as the front
speakers.
YPAO:Natural
Adjusts all speakers to achieve a natural sound.
Through
Does not use the equalizer.
X
• To play Dolby Atmos contents using the front presence speakers, see “Presence speaker layout” (p.19).
“YPAO:Flat”, “YPAO:Front”, and “YPAO:Natural” are available only when the measurement results of “Auto
Setup” have already been saved (p.40). Press ENTER again to view the measurement results.
⬛ Distance
⬛ Manual equalizer adjustment
Sets the distance between each speaker and listening position so that sounds from the
speakers reach the listening position at the same time. First, select the unit of distance from
“Meter” or “Feet”.
Choices
Front L, Front R, Center, Surround L, Surround R, Surround Back L, Surround Back R, Front Presence L, Front
Presence R, Subwoofer
1
Set “Parametric EQ” to “Manual” and press ENTER.
2
3
Press ENTER again to enter the edit screen.
Use the cursor keys to select a speaker and press ENTER.
X
Setting range
0.30 m to 3.00 m to 24.00 m (1.0 ft to 10.0 ft to 80.0 ft), *0.05 m (0.2 ft) increments
• To restore the default settings for all speakers, select “PEQ Data Clear” and then “OK”.
• To copy the parametric equalizer values acquired with “Auto Setup” (p.40) to the “Manual” fields for fine
⬛ Level
adjustment, select “PEQ Data Copy” and then an equalizer type.
4
Adjusts the volume of each speaker.
Use the cursor keys (e/r) to select a center frequency from the 7 preset bands (4 for
subwoofer) and the cursor keys (q/w) to adjust the gain.
Choices
Front L, Front R, Center, Surround L, Surround R, Surround Back L, Surround Back R, Front Presence L, Front
Presence R, Subwoofer
Setting range
-10.0 dB to 0.0 dB to +10.0 dB (0.5 dB increments)
Setting range
Gain: -20.0 dB to +6.0 dB
En
109
5
Sound
To fine-adjust the center frequency or Q factor (bandwidth), press ENTER repeatedly to select
an item.
Configures the audio output settings.
Frequency: Use the cursor keys (e/r) to adjust the center frequency of the selected band and
the cursor keys (q/w) to adjust the gain.
Q: Use the cursor keys (e/r) to adjust the Q factor (bandwidth) of the selected band and the
cursor keys (q/w) to adjust the gain.
Setting range
Center frequency: 15.6 Hz to 16.0 kHz (15.6 Hz to 250.0 Hz for subwoofer)
Q factor: 0.500 to 10.080
6
To exit from the menu, press ON SCREEN.
⬛ Test Tone
⬛ Lipsync
Enables/disables the test tone output. Test tone output helps you to adjust the speaker
Adjusts the delay between video and audio output.
balance or equalizer while confirming its effect.
Delay Enable
Settings
Off
Does not output test tones.
On
Outputs test tones automatically when you adjust the speaker balance or
equalizer.
Enables/disables the Lipsync adjustment for each input source.
Choices
HDMI 1-5, AV 1-2, VIDEO AUX, AUDIO 1-5
Settings
Disable
Disable the Lipsync adjustment for the selected input source.
Enable
Enables the Lipsync adjustment for the selected input source.
Auto/Manual Select
Selects the method to adjust the delay between video and audio output.
Setting range
Auto
Adjusts the delay between video and audio output automatically when a TV that
supports an automatic lipsync function is connected to the unit via HDMI.
If necessary, you can fine-adjust the audio output timing in “Adjustment”.
Manual
Select this option when you want to adjust the delay between video and audio
output manually.
Adjust the audio output timing in “Adjustment”.
X
Even if “Auto/Manual Select” is set to “Auto”, the automatic adjustment does not work depending on the TV
connected to the unit. In this case, adjust the delay manually in “Adjustment”.
En
110
⬛ Adaptive DSP Level
Adjustment
Adjusts the delay between video and audio output manually when “Auto/Manual Select” is set
Selects whether to automatically adjust the CINEMA DSP effect level when the volume is
to “Manual”. You can fine-adjust the audio output timing when “Auto/Manual Select” is set to
adjusted.
“Auto”.
Settings
Setting range
0 ms to 500 ms (1 ms increments)
X
• “Offset” shows the difference between automatic adjustment and fine adjustment.
Off
Does not adjust the effect level automatically.
On
Adjusts the effect level automatically.
⬛ CINEMA DSP 3D Mode
• This setting is also available in “Lipsync Adjustment” (p.92) in the “Option” menu.
Enables/disables CINEMA DSP 3D (p.58). If this function is set to “On”, CINEMA DSP 3D
⬛ Dynamic Range
functions with the selected sound programs (except 2ch Stereo and 7ch Stereo).
Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS
Settings
signals) playback.
Off
Disables CINEMA DSP 3D.
Settings
On
Enables CINEMA DSP 3D.
Maximum
Produces audio without adjusting the dynamic range.
Standard
Optimizes the dynamic range for regular home use.
⬛ Virtual Surround Back Speaker
Sets the dynamic range for clear sound even at night or at low volumes.
Selects whether to create Virtual Surround Back Speaker (VSBS) using the surround speakers.
When playing back Dolby TrueHD signals, the dynamic range is automatically
adjusted based on the input signal information.
When VSBS is enabled, the unit creates VSBS when no surround back speakers are connected.
Minimum/Auto
Settings
⬛ Max Volume
Sets the limit value of the volumes.
On
Enables Virtual Surround Back Speaker (VSBS).
VSBS is effective only when 6.1- or 7.1-channel content is played back.
⬛ Initial Volume
Sets the initial volume when the receiver is turned on.
Settings
On
Disables Virtual Surround Back Speaker (VSBS).
X
Setting range
-30.0 dB to +15.0 dB (5.0 dB increments), +16.5 dB
Off
Off
Sets the level to the volume level of the unit when it last entered standby mode.
Sets at Mute or the specified volume level (-80 dB to +16.5 dB, 0.5 dB increments).
(This setting works only when the initial volume is set lower than “Max Volume”.)
En
111
⬛ Object Decode Mode
Video
Enables/disables playback of object-based audio signals such as Dolby Atmos or DTS:X
Configures the video output settings.
contents.
Settings
Disable
Disables playback of object-based audio signals. Those signals will be played in
normal 5.1-/7.1-channel audio.
Enable
Enables playback of object-based audio signals.
X
Regardless of this setting, object-based audio signals are played in normal 5.1-/7.1-channel audio if any of
CINEMA DSP programs is selected.
⬛ Video Mode
Enables/disables the video signal processing (resolution and aspect ratio).
Settings
Direct
Processing
Disables the video signal processing.
Enables the video signal processing.
Select a resolution and an aspect ratio in “Resolution” and “Aspect”.
X
• When “Video Mode” is set to “Direct”, the unit transmits video signals with the least circuitry in order to reduce
video output delay.
• When “Video Mode” is set to “Processing” and the resolution is being converted, short messages are not
displayed on the TV screen.
Resolution
Selects a resolution to output HDMI video signals when “Video Mode” is set to “Processing”.
Settings
Through
Does not convert the resolution.
Auto
Selects a resolution automatically in accordance with TV resolution.
480p/576p, 720p,
1080i, 1080p, 4K
Output video signals with a selected resolution.
(Only the resolutions supported by your TV are selectable.)
X
If you need to select a resolution that is not supported by your TV, set “MON.CHK” (p.127) in the “ADVANCED
SETUP” menu to “SKIP” and try again. (Note that the output video may not be displayed on your TV normally.)
En
112
HDMI
Aspect
Selects an aspect ratio to output HDMI video signals when “Video Mode” is set to “Processing”.
Configures the HDMI settings.
Settings
Through
Does not convert the aspect ratio.
16:9 Normal
Outputs 4:3 video signals to a 16:9 TV with black bands on either side of the
screen.
X
This setting functions only when 480i/576i or 480p/576p signals are converted into 720p, 1080i, 1080p, or 2160p
(4K) signals.
⬛ HDMI Control
Enables/disables HDMI Control (p.145).
Settings
Off
On
Disables HDMI Control.
Enables HDMI Control.
Configure the settings in “TV Audio Input”, “ARC” and “Standby Sync”.
Y
To use HDMI control, you need to perform the HDMI Control link setup (p.145) after connecting HDMI
Control-compatible devices.
TV Audio Input
Selects an audio input jack of the unit to be used for TV audio input when “HDMI Control” is set
to “On”. The unit’s input source automatically switches to TV audio when the TV input is
switched to its built-in tuner.
Settings
AV 1-2, AUDIO 1-5
Default
AUDIO 1
Y
When using ARC to input TV audio to the unit, you cannot use the input jacks selected here for connecting an
external device because the input will be used for TV audio input.
En
113
⬛ Audio Output
ARC
Enables/disables ARC (p.146) when “HDMI Control” is set to “On”.
Selects a device to output audio.
Settings
X
Off
Disables ARC.
On
Enables ARC.
This setting is available only when “HDMI Control” is set to “Off”.
HDMI OUT (TV)
Y
Enables/disables the audio output from a TV connected to the HDMI OUT jack.
You do not need to change this setting normally. In case noises are produced from the speakers connected to the
Settings
unit because TV audio signals input to the unit via ARC are not supported by the unit, set “ARC” to “Off” and use
the TV’s speakers.
Standby Sync
Off
Disables the audio output from the TV.
On
Enables the audio output from the TV.
⬛ Standby Through
Select whether to use HDMI control to link the standby behavior of the TV and the unit when
“HDMI Control” is set to “On”.
Select whether to output videos/audio (input through HDMI jacks) to the TV when the unit is in
Settings
standby mode. If this function is set to “On” or “Auto”, you can use the input selection keys
Off
Does not set the unit to standby mode when the TV is turned off.
(HDMI 1-5, VIDEO AUX) to select an HDMI input even when the unit is in standby mode (the
On
Sets the unit to standby mode when the TV is turned off.
standby indicator on the unit blinks).
Auto
Sets the unit to standby mode when the TV is turned off only when the unit is
receiving TV audio or HDMI signals.
Settings
Off
En
114
(This setting is available only when “HDMI Control” is set to “Off”.)
Does not output videos/audio to the TV.
On
Outputs videos/audio to the TV.
(The unit consumes more power than when “Off” is selected.)
Auto
Outputs videos/audio to the TV. If no signals are detected, the unit is set to the
power saving mode.
Network
⬛ Manual network settings
Configures the network settings.
1
2
Set “DHCP” to “Off”.
Use the cursor keys (q/w) to select a parameter type and press ENTER.
IP Address
3
⬛ Network Connection
Specifies an IP address.
Subnet Mask
Specifies a subnet mask.
Default Gateway
Specifies the IP address of the default gateway.
DNS Server (P)
Specifies the IP address of the primary DNS server.
DNS Server (S)
Specifies the IP address of the secondary DNS server.
Use the cursor keys (e/r) to move the edit position and the cursor keys (q/w) to select a
value.
Selects the network connection method.
Settings
Wired
Select this option when you want to connect the unit to a network with a
commercially-available network cable (p.35)
Wireless (Wi-Fi)
Select this option when you want to connect the unit to a network via the
wireless router (access point). For details on settings, see “Connecting the unit to
a wireless network” (p.47).
Wireless Direct
Select this option when you want to connect a mobile device to the unit directly.
For details on settings, see “Connecting a mobile device to the unit directly
(Wireless Direct)” (p.52).
4
To confirm the setting, press ENTER.
5
To configure another network parameter, repeat steps 2 to 4.
6
To save the changes, use the cursor keys to select “OK” and press ENTER.
7
To exit from the menu, press ON SCREEN.
⬛ Network Standby
Selects whether the unit can be turned on from other network devices (network standby).
Settings
⬛ IP Address
Off
Configures the network parameters (such as IP address).
On
DHCP
Disables the network standby function.
Enables the network standby function.
(The unit consumes more power than when “Off” is selected.)
Enables the network standby function.
Select whether to use a DHCP server.
Auto
Settings
Off
Does not use a DHCP server. Configure the network parameters manually. For
details, see “Manual network settings”.
On
Uses a DHCP server to automatically obtain the unit’s network parameters (such
as IP address).
(If “Network Connection” is set to “Wired”, the unit is set to the power saving
mode when the network cable is disconnected.)
With an advanced energy saving design, this product achieves a low power consumption of not
more than two watts when in Network Standby mode.
En
115
⬛ MAC Address Filter
⬛ Network Name
Sets the MAC address filter to limit access to the unit from other network devices.
Edits the network name (the unit’s name on the network) displayed on other network devices.
⬛ Setup procedure
Filter
Enables/disables the MAC address filter.
1
Press ENTER to enter the name edit screen.
Settings
2
Use the cursor keys and ENTER to rename and select “ENTER” to confirm the entry.
Off
Disables the MAC address filter.
On
Enables the MAC address filter. In “MAC Address 1-10”, specify the MAC addresses
of the network devices that will be permitted access to the unit.
X
AirPlay (p.79) and DMC (p.96) operations are not subject to the MAC address filter.
MAC Address 1-10
Specifies the MAC addresses (up to 10) of the network devices that will be permitted access to
X
the unit when “Filter” is set to “On”.
To clear the entry, select “CLEAR”.
⬛ Setup procedure
1
3
Use the cursor keys to select “OK” and press ENTER.
Use the cursor keys (q/w) to select “MAC Address 1-5” or “MAC Address 6-10” and press
X
ENTER.
To restore the default setting, select “RESET”.
2
Use the cursor keys (q/w) to select an MAC address number and press ENTER.
4
3
Use the cursor keys (e/r) to move the edit position and the cursor keys (q/w) to select a
⬛ MusicCast Link Power Interlock
value.
To exit from the menu, press ON SCREEN.
Selects whether turning on the power of the master device of the MusicCast network (this unit)
4
To confirm the setting, press ENTER.
also turns on the power of other devices of the network.
5
To save the changes, use the cursor keys to select “OK” and press ENTER.
Settings
6
To exit from the menu, press ON SCREEN.
En
116
Off
Disables the power interlock from the unit (MusicCast master).
On
Enables the power interlock from the unit (MusicCast master).
⬛ Audio Send
Bluetooth
Configures the Bluetooth settings when the unit is used as the Bluetooth audio transmitter.
Configures the Bluetooth settings.
Transmitter
Enables/disables the Bluetooth audio transmitter function.
When this function is enabled, you can enjoy audio played back on the unit using Bluetooth
speakers/headphones (p.68).
Settings
⬛ Bluetooth
Enables/disables the Bluetooth function (p.67).
Settings
Off
Disables the Bluetooth function.
On
Enables the Bluetooth function.
⬛ Audio Receive
Configures the Bluetooth settings when the unit is used as the Bluetooth audio receiver.
Bluetooth Standby
Selects whether to enable/disable the function that turns on the unit from Bluetooth devices
(Bluetooth standby). If this function is set to “On”, the unit automatically turns on when a
connect operation is performed on the Bluetooth device.
Settings
Off
On
Disables the Bluetooth standby function.
Enables the Bluetooth standby function.
(The unit consumes more power than when “Off” is selected.)
X
This setting is not available when “Network Standby” (p.115) is set to “Off”.
En
117
Off
Disables the Bluetooth audio transmitter function.
On
Enables the Bluetooth audio transmitter function.
⬛ Zone2 Set
Multi Zone
Configures the Zone2 settings.
Configures the multi zone settings.
Volume
Enables/disables volume adjustments for Zone2 output.
If you have connected an external amplifier with volume control to the unit, disable volume
adjustments for Zone2.
Settings
⬛ Main Zone Set
Fixed
Disables volume adjustments for Zone2 output.
Variable
Enables volume adjustments for Zone2 output.
X
Configures the main zone setting.
This setting is not available when “Power Amp Assign” (p.107) is set to “7.1 +1Zone” or “5.1.2 +1Zone”.
Max Volume
Zone Rename
Changes the zone name (for main zone) displayed on the TV screen.
Sets the Zone2 limit value of the volumes.
⬛ Setup procedure
Setting range
-30.0 dB to +10.0 dB (5.0 dB increments)
1
2
Press ENTER to enter the name edit screen.
X
Use the cursor keys and ENTER to rename and select “ENTER” to confirm the entry.
This setting is available only when “Power Amp Assign” (p.107) is set to “7.1 +1Zone” or “5.1.2 +1Zone”.
Initial Volume
Sets the Zone2 initial volume for when the unit is turned on.
Settings
3
Off
Sets the level at the volume level of the unit when it last entered standby mode.
On
Sets at Mute or the specified volume level (-80 dB to +10.0 dB, 0.5 dB increments).
(This setting works only when the initial volume is set lower than “Max Volume”.)
X
X
To clear the entry, select “CLEAR”.
This setting is available only when “Power Amp Assign” (p.107) is set to “7.1 +1Zone” or “5.1.2 +1Zone”.
Use the cursor keys to select “OK” and press ENTER.
Audio Delay
X
Adjusts the time deviation in relation to the main zone.
To restore the default setting, select “RESET”.
4
Setting range
0 ms to 100 ms (1 ms increments)
To exit from the menu, press ON SCREEN.
En
118
Mono
Balance
Switches between stereo and monaural for Zone2 output.
Adjusts the volume balance for Zone2 output.
Settings
Setting range
-20 to 0 to +20, increments of 1
Off
Produces stereo sounds in Zone2.
On
Produces monaural sounds in Zone2.
Zone Rename
Changes the zone name (for Zone2) displayed on the TV screen.
Enhancer
You can change the zone name in the same manner as “Zone Rename” in “Main Zone Set”
Enables/disables Compressed Music Enhancer (p.62) for Zone2 output.
(p.118).
Settings
Off
Disables Compressed Music Enhancer.
⬛ Party Mode Set
On
Enables Compressed Music Enhancer.
Enables/disables switching to the party mode (p.84).
Choice
Target: Zone 2
Tone Control
Settings
Adjusts the level of high-frequency range (Treble) and low-frequency range (Bass) for Zone2
output.
Disable
Disables switching to the party mode.
Settings
Enable
Enables switching to the party mode. You can turn on/off the party mode by
pressing PARTY on the remote control.
Auto
Adjusts the levels of the high-frequency range (Treble) and low-frequency range
(Bass) automatically in synchronization with the main volume, with correction
for the auditory response of the human ear.
Manual
Adjusts the level of high-frequency range (Treble) and low-frequency range (Bass)
manually (-6.0 to +6.0 dB, 0.5 dB increments).
Bypass
Does not adjust the level of high-frequency range (Treble) and low-frequency
range (Bass).
Extra Bass
Enables/disables Extra Bass for Zone2 output. When Extra Bass is enabled, you can enjoy
enhanced bass sounds, regardless of the size of speakers.
Settings
Off
Disables Extra Bass.
On
Enables Extra Bass.
En
119
⬛ Display Set
Function
Configures the settings related to the front display and TV screen display.
Configures the functions that make the unit easier to use.
Dimmer (Front Display)
Adjusts the brightness of the front display.
Setting range
-4 to 0 (higher to brighten)
Y
The front display may become dark when “ECO Mode” (p.122) is set to “On”.
Short Message
⬛ Remote PROGRAM Key
Selects whether to display short messages on the TV screen when the unit is operated (such as
Select the function that is assigned to the PROGRAM key on the remote control.
input selection and volume adjustment).
When "INPUT Selection" is selected, the PROGRAM key on the remote control will operate as
Settings
the input switching key.
Settings
On
Displays short messages on the TV screen.
Off
Does not display short messages on the TV screen.
DSP Program Selection
Enables switching the DSP Programs.
INPUT Selection
Enables switching the INPUT sources.
NET Selection
Enables switching the NETWORK sources.
Selects the image to be used as wallpaper on the TV.
Preset Selection
Enables switching between the preset radio stations and registered
favorite items (shortcut) (p.85).
Settings
Browse Screen - 1 page Up/Down
Enables scrolling the Browse Screen.
Piano
Displays the piano image on the TV screen when there is no video signal.
Subwoofer Trim
Enables fine-adjusting the subwoofer volume.
Gray
Displays a gray background on the TV screen when there is no video signal.
Dialogue Level
Enables adjusting the volume of dialogue sounds.
q Repeat /w Shuffle
Enables switching shuffle/repeat settings.
Wallpaper
Y
This setting does not change the function of the PROGRAM key on the front panel.
En
120
⬛ Trigger Output
Target Zone
Sets the TRIGGER OUT jack to function in sync with the power status of each zone or input
Specifies the zone with which the TRIGGER OUT jack functions are synchronized.
switching.
Settings
Trigger Mode
Main
Specifies the condition for the TRIGGER OUT jack to function.
Settings
Power
Source
The TRIGGER OUT jack functions in sync with the power status of the zone
specified with “Target Zone.”
Zone2
The TRIGGER OUT jack functions in sync with the input switching in the zone
specified with “Target Zone.”
An electronic signal is transmitted according to the setting made in “Source.”
Manual
All
Select this to manually switch the output level for electronic signal transmission
with “Manual.”
When “Trigger Mode” is set to “Power,” electronic signal transmission is
synchronized with the power status of the main zone.
When “Trigger Mode” is set to “Source,” electronic signal transmission is
synchronized with the input switching in the main zone.
When “Trigger Mode” is set to “Power,” electronic signal transmission is
synchronized with the power status of Zone2.
When “Trigger Mode” is set to “Source,” electronic signal transmission is
synchronized with the input switching in Zone2.
When “Trigger Mode” is set to “Power,” electronic signal transmission is
synchronized with the power status of the main zone or Zone2.
When “Trigger Mode” is set to “Source,” electronic signal transmission is
synchronized with the input switching in the main zone or Zone2.
Source
⬛ Memory Guard
Specifies the output level of the electronic signal transmitted with each input, switching when
Prevents accidental changes to the settings.
“Trigger Mode” is set to “Source”.
Settings
Choices
HDMI 1-5, AV 1-2, VIDEO AUX, AUDIO 1-5, TUNER, PHONO, (network sources), Bluetooth, USB, AirPlay,
MusicCast Link, SERVER, NET RADIO
Settings
Stops the electronic signal transmission when you switch to the input source
specified in this option.
High
Transmits the electronic signal when you switch to the input source specified in
this option.
set to “Manual”. This setting can also be used to confirm proper function of the external device
connected via the TRIGGER OUT jack.
Choices
Stops the electronic signal transmission.
Protects the settings until “Off” is selected.
Icon
Switches the output level for electronic signal transmission manually when “Trigger Mode” is
Transmits the electronic signal.
On
When “Memory Guard” is set to “On”, the lock icon (o) is displayed on the menu screen.
Manual
High
Does not protect the settings.
X
Low
Low
Off
En
121
⬛ ECO Mode
ECO
Enables/disables the eco (power saving) mode.
Configures the power supply settings.
You can reduce the unit’s power consumption by setting “ECO Mode” to “On”. After setting, be
sure to press ENTER to restart the unit.
Settings
Off
Disables the eco mode.
On
Enables the eco mode.
Y
• When “ECO Mode” is set to “On”, the front panel display may become dark.
• If you want to play audio at high volume, set “ECO Mode” to “Off”.
⬛ Auto Power Standby
Sets the amount of time for the auto-standby function. If you do not operate the unit or if no
input signals are detected for the specified time, the unit will automatically go into standby
mode.
Settings
Off
Does not set the unit to standby mode automatically.
20 Minutes
Sets the unit to standby mode when you have not operated the unit and no input
signals are detected for 20 minutes.
2 Hours, 4 Hours,
8 Hours, 12 Hours
Sets the unit to standby mode when you have not operated the unit for the
specified time. For example, when “2 Hours” is selected, the unit will switch to
standby mode if you do not operate it for 2 hours.
Default
U.K. and Europe models: 20 Minutes
Other models: Off
X
Just before the unit enters standby mode, “AutoPowerStdby” appears and then countdown starts in the front
display.
En
122
Language
Viewing information about the unit
(Information menu)
Select an on-screen menu language.
You can view information about the unit using the TV screen.
1
2
Press ON SCREEN.
3
Use the cursor keys (e/r) to select an information type.
4
To exit from the menu, press ON SCREEN.
Use the cursor keys to select “Information” and press ENTER.
Settings
English, 日本語 , Français, Deutsch, Español, Русский, Italiano, 中文
X
The information on the front display is provided in English only.
En
123
⬛ HDMI Monitor
Types of information
Displays information about the TVs connected to the HDMI OUT jacks.
You can check the following information in the Information menu.
⬛ Audio Signal
Interface
TV interface
Video Resolution
Resolutions supported by the TV
Displays information about the current audio signal.
Format
Channel
⬛ Network
Audio format of the input signal
The number of source channels in the input signal
(front/surround/LFE)
Displays the network information on the unit.
For example, “5.1 (3/2/0.1)” means 5.1ch in total (3 front channels,
2 surround channels, and LFE).
(When using wired or wireless [Wi-Fi] network connection)
Input
IP Address
(When DTS:X content is played back)
For example, “7.1.4” denotes “standard 7.1-channel plus 4 for
overhead speaker channels”.
Output
IP address
Subnet Mask
Subnet mask
Default Gateway
The IP address of the default gateway
Sampling
The number of samples per second of the input digital signal
DNS Server (P)
The IP address of the primary DNS server
Dialogue
The dialogue normalization level of the input bitstream signal
DNS Server (S)
The IP address of the secondary DNS server
The number of signal output channels (for example, “5.1.2”
denotes “standard 5.1-channel plus 2 for overhead speaker
channels”) and the speaker terminals from which signals are
output
MAC Address (Ethernet)
Channel
MAC address
MAC Address (Wi-Fi)
Network Name
Network name (the unit’s name on the network)
X
Wired/Wireless
The status of the wired or wireless connection
Even when the unit is set to output bitstream signals directly, the signal may be converted depending on the
SSID
specifications and settings of the playback device.
⬛ Video Signal
Displays information about the current video signal.
HDMI Signal
Presence or absence of HDMI signal input/output
HDMI Resolution
Resolutions of input signal (analog or HDMI) and output signal (HDMI)
Analog Resolution
Resolutions of input signal (analog)
En
124
(When using wireless [Wi-Fi] network connection)
The SSID of the wireless network
Configuring the system settings
(ADVANCED SETUP menu)
(When using Wireless Direct)
SSID
The SSID of the wireless network
Security
Security method
Security Key
Security key
IP Address
IP address
Subnet Mask
Subnet mask
Configure the system settings of the unit while viewing the front display.
1
2
MAC Address (Wi-Fi)
MAC address
Network Connection
“Wireless Direct” indication
Set the unit to standby mode.
While holding down STRAIGHT on the front panel, press MAIN ZONE z.
MAIN ZONE z
⬛ System
Displays the system information on the unit.
Remote ID
The unit’s remote control ID setting (p.126)
TV Format
The unit’s video signal type (p.127)
Speaker Impedance
The speaker impedance setting of the unit (p.126)
Tuner Freq. Step
PROGRAM
3
4
5
(Asia and General models only)
The FM/AM tuning frequency setting of the unit (p.126)
System ID
System ID number
Firmware Version
The version of firmware installed on the unit
If the unit detects a newer firmware over the network,
(mail icon) appears at the upper right of the
“Information” and “System” icons, and the corresponding message will be displayed in this screen, the menu
screen and the front panel on the unit. You can update the unit’s firmware by pressing ENTER in this screen and
following the procedure in “Updating the unit’s firmware via the network” (p.129).
⬛ Multi Zone
Displays information about Zone2.
Input
The input source selected for Zone2
Volume
The volume setting for Zone2
Press PROGRAM to select an item.
Press STRAIGHT to select a setting.
Press MAIN ZONE z to set the unit to standby mode and turn it on again.
The new settings take effect.
X
En
125
STRAIGHT
ADVANCED SETUP menu items
Selecting the remote control ID (REMOTE ID)
X
LINK MASTER
OUT
2
ECO
Default settings are underlined.
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
REMOTE ID••ID1
Item
Function
Page
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
Change the unit’s remote control ID so that it matches the remote control’s ID (default: ID1).
SP IMP.
Changes the speaker impedance setting.
126
When using multiple Yamaha AV receivers, you can set each remote control with a unique
REMOTE ID
Selects the unit’s remote control ID.
126
remote control ID for its corresponding receiver.
126
Settings
ID1, ID2
⬛ Changing the remote control ID of the remote control
(Taiwan, Brazil, Asia and General models only)
TU
Changes the FM/AM tuning frequency setting.
TV FORMAT
Switches the video signal type.
127
MON.CHK
Removes the limitation on HDMI video output.
127
4K MODE
Selects the HDMI 4K signal format.
127
DTS MODE
This setting informs the player about the DTS formats that the unit
supports.
128
INIT
Restores the default settings.
128
UPDATE
Updates the firmware.
128
VERSION
Checks the version of firmware currently installed on the unit.
128
1
To select ID1, hold down the cursor key (e) and SCENE1 together for 3 seconds.
To select ID2, hold down the cursor key (e) and SCENE2 together for 3 seconds.
Changing the FM/AM tuning frequency setting (TU)
(Taiwan, Brazil, Asia and General models only)
LINK MASTER
OUT
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
TU••••FM50/AM9
Changing the speaker impedance setting (SP IMP.)
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
Change the FM/AM tuning frequency setting of the unit depending on your country or region.
LINK MASTER
OUT
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
SP IMP.••8¬MIN
Settings
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
FM100/AM10
Select this when you want to adjust the FM frequency by 100-kHz steps and AM by
10-kHz steps.
FM50/AM9
Select this when you want to adjust the FM frequency by 50-kHz steps and AM by
9-kHz steps.
Change the unit’s speaker impedance settings depending on the impedance of the speakers
connected.
Settings
6 Ω MIN
Select this option when you connect 6-ohm speakers to the unit. You can also use
4-ohm speakers as the front speakers.
8 Ω MIN
Select this option when you connect 8-ohm or higher speakers to the unit.
En
126
Switching the video signal type (TV FORMAT)
LINK MASTER
OUT
2
ECO
Selecting the HDMI 4K signal format (4K MODE)
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
TV FORMAT•NTSC
LINK MASTER
OUT
2
ECO
VOL. MUTE VIRTUAL
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
4K MODE•MODE 1
FPR
FPL
SW
SR
SL
SBL SB SBR
Switch the video signal type of the unit so that it matches to the format of your TV.
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
Selects the format of signals input/output at the unit when HDMI 4K compatible TV and
playback device are connected to the unit.
Settings
NTSC, PAL
Settings
Default
U.S.A., Canada, Korea, Taiwan, Brazil and General models: NTSC
Inputs/outputs 4K signals shown in the table below.
MODE 1
Other models: PAL
Removing the limitation on HDMI video output
(MON.CHK)
MODE 2
(4:2:0 format only for VIDEO AUX [HDMI IN] jack)
Depending on the connected device or HDMI cables, video may not be displayed
correctly. In this case, select “MODE 2”.
Inputs/outputs 4K signals shown in the table below.
Y
When “MODE 1” is selected, use a Premium High Speed HDMI Cable or Premium High Speed Cable with Ethernet.
LINK MASTER
OUT
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
MON.CHK••••YES
Format
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
MODE 1
The unit automatically detects resolutions supported by a TV connected to the HDMI OUT jack.
8 bit
Disable the monitor check function if you want to specify a resolution in “Resolution” (p.112)
when the unit cannot detect the TV’s resolution or when you want to specify a different
SKIP
Disables the monitor check function. (Outputs video signals with a specified
resolution regardless of compatibility with the TV.)
YCbCr 4:4:4
✔
YCbCr 4:2:2
Settings
YES
✔
4K/60, 50 Hz
resolution than the detected resolution.
Enables the monitor check function. (Outputs video signals with a resolution
supported by the TV only.)
RGB 4:4:4
4K/30, 25, 24 Hz
Y
Reset to “YES” if the unit becomes inoperable because video from the unit cannot be displayed on the TV after
“MON.CHK” has been set to “SKIP”.
En
127
MODE 2
10 bit
12 bit
8 bit
10 bit
–
–
–
–
✔
12 bit
–
YCbCr 4:2:0
✔
✔
–
RGB 4:4:4
✔
✔
–
YCbCr 4:4:4
✔
✔
YCbCr 4:2:2
✔
–
✔
DTS Format Notification Setting (DTS MODE)
LINK MASTER
OUT
2
ECO
Updating the firmware (UPDATE)
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
DTS MODE•MODE1
LINK MASTER
OUT
2
ECO
VOL. MUTE VIRTUAL
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
UPDATE•••••USB
FPR
FPL
SW
SR
SL
SBL SB SBR
This setting informs the player about the DTS formats that the unit supports.
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
New firmware that provides additional features or product improvements will be released as
needed. Updates can be downloaded from the Yamaha website. If the unit is connected to the
Settings
Internet, you can download the firmware via the network. For details, refer to the information
MODE 1
MODE 2
This mode conforms to the DTS:X standard.
supplied with updates.
Use this setting under normal circumstances.
⬛ Firmware update procedure
Use this setting if the player fails to properly output a DTS signal even when it is
playing back DTS-HD or DTS:X content.
Do not perform this procedure unless firmware update is necessary. Also, make sure you read the
information supplied with updates before updating the firmware.
1
Restoring the default settings (INIT)
Press STRAIGHT repeatedly to select “USB” or “NETWORK” and press INFO to start firmware
update.
LINK MASTER
OUT
2
ECO
Choices
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
INIT••••CANCEL
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
Restores the default settings for the unit.
USB
Update the firmware using a USB memory device.
NETWORK
Update the firmware via the network.
X
Choices
VIDEO
Restores the default settings for video configurations.
ALL
Restores the default settings for the unit.
CANCEL
Does not perform an initialization.
If the unit detects newer firmware over the network, the corresponding message will be displayed after
ON SCREEN is pressed. In this case, you can also update the unit’s firmware by following the procedure in
“Updating the unit’s firmware via the network” (p.129).
Checking the firmware version (VERSION)
LINK MASTER
OUT
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
VERSION••xx.xx
VOL. MUTE VIRTUAL
FPR
FPL
SW
SR
SL
SBL SB SBR
Check the version of firmware currently installed on the unit.
X
• You can also check the firmware version in “System” (p.125) in the “Information” menu.
• It may take a while until the firmware version is displayed.
En
128
Updating the unit’s firmware via the network
New firmware that provides additional features or product
1
2
3
4
Internet, you can download the firmware via the network and update it.
5
V-AUX
AUDIO
1
2
3
4
Note
AV
5
1
2
TUNER
BLUETOOTH
USB
NET
PHONO
PARTY
HDMI OUT
MAIN
ZONE 2
• Do not operate the unit or disconnect the power cable or network cable
during firmware update. Firmware update takes about 20 minutes or more
(depending on your Internet connection speed).
• If the Internet connection speed is slow, or the unit is connected to the
wireless network, network update may not be possible depending on the
condition of the wireless connection. In this case, update the firmware using
the USB memory device (p.128).
SCENE
2
1
3
PROGRAM MUTE
4
1
2
• To perform the following procedure, your TV must be connected to the unit
via HDMI. If not, perform the update from the “ADVANCED SETUP” menu
(p.125).
ON
SCREEN
• For details on update, visit the Yamaha website.
OPTION
Cursor keys
ENTER
ENTER
RETURN
TUNING
3
X
• You can also update the firmware using the USB memory device from the “ADVANCED
X
unit’s firmware by pressing ENTER in the “System” screen.
Information icon
• The firmware update indicator on the front display lights up when a firmware update
MOVIE
MUSIC
INFO
SLEEP
1
2
3
4
A firmware update is available if the following message is displayed after
5
6
7
8
ON SCREEN is pressed.
9
0
MEMORY
ENT
ENHANCER PURE DIRECT
The firmware update is complete.
and a message will be displayed in the “System” screen (p.125). You can update the
SETUP” menu (p.128).
PRESET
If “Update Success Please Power Off!” appears on the
front display, press MAIN ZONE z on the front panel.
(mail icon) appears at the upper right of the “Information” and “System” icons,
BAND
SUR. DECODE STRAIGHT
To start the firmware update, use the Cursor keys to
select “START” and press ENTER.
If you want to cancel without doing anything now, press the “CLOSE” button.
DISPLAY
MODE
Read the on-screen description.
The on-screen display turns off.
VOLUME
POP-UP/MENU
TOP MENU
Updating the unit’s firmware immediately
improvements will be released as needed. If the unit is connected to the
HDMI
is available via the network.
Message
System Icon
En
129
Updating the unit’s firmware at power off
1
2
Read the on-screen description.
To set the firmware to update at power off, use the Cursor keys to select
“LATER” and press ENTER.
3
Press z (receiver power) to turn off the unit.
A screen asking you to confirm the firmware update is displayed.
LINK MASTER
OUT
2
ECO
STEREO TUNED ZONE
SLEEP PARTY 2 A 3 B
Hi -Res ENHANCER YPAO VOL. A- DRC
UPDATE ENTER
4
MUTE VIRTUAL
FPL
SBL
FPR
SB
SBR
To start the firmware update, press ENTER.
After the firmware update is complete, the unit will turn off automatically.
Y
• The firmware update can be started by pressing INFO on the front panel.
• The unit turns off automatically without performing the firmware update if 2 minutes pass after the
screen to confirm the firmware update is displayed.
• To cancel the firmware update process, press RETURN, and the unit will turn off.
• The unit turns off without performing the firmware update if you turn off the unit with AV CONTROLLER
or MusicCast CONTROLLER.
En
130
APPENDIX
Frequently asked questions
every time you add a new HDMI Control-compatible device to your system. For information on
The new speaker system does not provide an ideal sound
balance...
how HDMI Control works between your TV and playback devices, refer to the instruction
manuals for each device.
If you have changed speakers or have a new speaker system, use “Auto Setup” to optimize the
I want to turn off the on-screen messages displayed during
operations...
speaker settings again (p.40). If you want to adjust the speaker settings manually, use “Manual
Setup” in the “Setup” menu (p.107).
Since we have small children, we want to set limitations on the
volume control...
By default, short messages are displayed on the TV screen when the unit is operated (such as
If a small child accidentally operates the controls on the main unit or remote control, the
the short messages.
input selection and volume adjustment). If the short messages bother you when you are
watching movies or sports, configure “Short Message” (p.120) in the “Setup” menu to turn off
volume may suddenly increase. This may also cause injury or damage the unit or speakers. We
recommend using “Max Volume” in the “Setup” menu to set the maximum volume level for the
I want to prevent accidental changes to the settings...
unit in advance (p.111). You can also set the maximum volume for Zone2 (p.118).
You can protect the settings configured on the unit (such as speaker settings) by utilizing
I am occasionally startled by a sudden loud sound when turning
on the unit...
“Memory Guard” in the “Setup” menu (p.121).
By default, the volume level when the unit last entered standby mode is automatically applied.
The unit’s remote control is simultaneously controlling another
Yamaha product as well as the unit...
If you want to fix the volume, use “Initial Volume” in the “Setup” menu to set the volume to be
When using multiple Yamaha products, the remote control may work on another Yamaha
applied when the receiver is turned on (p.111). You can also set the initial volume for Zone2
product or another remote control may work on the unit. If this happens, register different
(p.118).
remote control IDs for the devices that you want to control with each remote control (p.126).
We are bothered by volume differences when switching
between input sources…
I want to enjoy videos/audio played back on the video device
even when the unit is in standby mode…
You can correct volume differences between input sources by utilizing “Input Trim” in the
If you have connected a video device to the unit with HDMI, you can output videos/audio
“Option” menu (p.93).
played back on the video device to the TV even when the unit is in standby mode. To use this
I made HDMI connections but HDMI Control does not work at
all...
function, set “Standby Through” (p.114) in the “Setup” menu to “On” or “Auto”. You can also
switch the input source using the remote control of the unit when this function is enabled.
To use HDMI Control, you need to perform the HDMI Control link setup (p.145). After
connecting HDMI Control-compatible devices (such as BD/DVD players) to the unit, enable
HDMI Control on each device and perform the HDMI Control link setup. This setup is required
En
131
Troubleshooting
Refer to the table below when the unit does not function properly.
If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or
service center.
First, check the following:
1
2
3
The power cables of the unit, TV and playback devices (such as BD/DVD players) are connected to AC wall outlets securely.
The unit, subwoofer, TV and playback devices (such as BD/DVD players) are turned on.
The connectors of each cable are securely inserted in to jacks on each device.
Power, system and remote control
Problem
Cause
Remedy
The power does not turn on.
The protection circuitry has been activated three times consecutively.
When the unit is in this condition, the standby indicator on the unit
blinks if you try to turn on the power.
The power does not turn off.
The internal microcomputer has frozen, due to an external electric shock Hold down MAIN ZONE z on the front panel for more than 10 seconds to initialize and
(such as lightning or excessive static electricity) or to a drop in the power reboot the unit. (If the problem persists, disconnect the power cable from the AC wall
supply voltage.
outlet and plug it again.)
The power turns off (standby mode) immediately.
The unit was turned on while a speaker cable was shorted.
Twist the bare wires of each speaker cable firmly and reconnect to the unit and speakers
(p.22).
The sleep timer worked.
Turn on the unit and start playback again.
The auto-standby function activated because the unit was not used for
the specified time.
To disable the auto-standby function, set “Auto Power Standby” in the “Setup” menu to
“Off” (p.122).
The speaker impedance setting is incorrect.
Set the speaker impedance to match your speakers (p.126).
The protection circuitry has been activated because of a short circuit.
Twist the bare wires of each speaker cable firmly and reconnect to the unit and speakers
(p.22).
As a safety precaution, capability to turn on the power is disabled. Contact your nearest
Yamaha dealer or service center to request repair.
The unit enters standby mode automatically.
The unit is not reacting.
The internal microcomputer is frozen, due to an external electric shock Hold down MAIN ZONE z on the front panel for more than 10 seconds to initialize and
(such as lightning or excessive static electricity) or to a drop in the power reboot the unit. (If the problem persists, disconnect the power cable from the AC wall
supply voltage.
outlet and plug it again.)
En
132
Problem
The unit cannot be controlled using the remote
control.
Cause
Remedy
The unit is out of the operating range.
Use the remote control within the operating range (p.5).
The batteries are weak.
Replace with new batteries.
The unit’s remote control sensor is exposed to direct sunlight or strong
lighting.
Adjust the lighting angle, or reposition the unit.
The remote control IDs of the unit and the remote control are not
identical.
Change the remote control ID of the unit or the remote control (p.126).
Audio
Problem
No sound.
Cause
Remedy
Another input source is selected.
Select an appropriate input source with the input selection keys.
Signals that the unit cannot reproduce are being input.
Some digital audio formats cannot be played back on the unit. To check the audio
format of the input signal, use “Audio Signal” in the “Information” menu (p.124).
The cable connecting the unit and playback device is defective.
If there is no problem with the connection, replace with another cable.
The maximum volume is set.
Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.111).
A device connected to the output jacks of the unit is not turned on.
Turn on all devices connected to the output jacks of the unit.
The volume cannot be increased.
The playback source does not contain a signal for the channel.
To check it, use “Audio Signal” in the “Information” menu (p.124).
The currently selected sound program/decoder does not use the
speaker.
To check it, use “Test Tone” in the “Setup” menu (p.110).
Audio output of the speaker is disabled.
Perform “Auto Setup” (p.40) or use “Configuration” in the “Setup” menu to change the
speaker settings (p.107).
The volume of the speaker is set too low.
Perform “Auto Setup” (p.40) or use “Level” in the “Setup” menu to adjust the speaker
volume (p.109).
The speaker cable connecting the unit and the speaker is defective.
If there is no problem with the connection, replace with another speaker cable.
The speaker is malfunctioning.
To check it, replace with another speaker. If the problem persists, the unit may be
malfunctioning.
The playback source does not contain LFE or low-frequency signals.
To check if the subwoofer is working properly, use “Test Tone” in the “Setup” menu
(p.110).
Subwoofer output is disabled.
Perform “Auto Setup” (p.40) or set “Subwoofer” in the “Setup” menu to “Use” (p.108).
The volume of the subwoofer is too low.
Adjust the volume on the subwoofer.
The subwoofer has been turned off by its auto-standby function.
Disable the auto-standby function of the subwoofer or adjust its sensitivity level.
No sound is coming from a specific speaker.
No sound is coming from the subwoofer.
En
133
Problem
No sound from the playback device (connected to the
unit with HDMI).
No sound from the playback device (when HDMI
Control is used).
No sound from the TV (when HDMI Control is used).
Cause
Remedy
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
Refer to the instruction manuals for the TV and check the TV’s specifications.
The unit is set not to output audio input through HDMI jacks from the
SPEAKERS terminals.
In “Audio Output” in the “Setup” menu, set “Amp” to “On” (p.114).
The number of devices connected to the HDMI OUT jack exceeds the
limit.
Disconnect some of the HDMI devices.
The TV is set to output audio from the TV speakers.
Change the audio output setting on your TV so that the playback device audio is output
from the speakers connected to the unit.
TV audio is selected as the input source.
Select an appropriate input source with the input selection keys.
The TV is set to output audio from the TV speakers.
Change the audio output setting on your TV so that the TV audio is output from the
speakers connected to the unit.
A TV that does not support ARC is connected to the unit only with an
HDMI cable.
Use a digital optical cable to make an audio connection (p.29).
(If the TV is connected to the unit with an audio cable)
The TV audio input setting does not match the actual connection.
(If you are trying to use ARC)
Set “ARC” in the “Setup” menu to “On” (p.114). Also, enable ARC on the TV.
ARC is disabled on the unit or TV.
Only the front speakers work on multichannel audio.
Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack (p.113).
The playback device is set to output 2-channel audio (such as PCM) only.
To check it, use “Audio Signal” in the “Information” menu (p.124). If necessary, change
the digital audio output setting on the playback device.
The unit is too close to another digital or radio frequency device.
Move the unit further away from the device.
The cable connecting the unit and playback device is defective.
If there is no problem with the connection, replace with another cable.
The volume of the unit is too high.
Turn down the volume. If “ECO Mode” is set to “On”, set it to “Off” (p.122).
A device connected to the unit’s output jacks is not turned on.
Turn on all devices connected to the unit’s output jacks.
Noise/hum is heard.
The sound is distorted.
En
134
Video
Problem
Cause
Remedy
Another input source is selected on the unit.
Select an appropriate input source with the input selection keys.
Another input source is selected on the TV.
Switch the TV input to display the video from the unit.
The video signal output from the unit is not supported by the TV.
Set “MON.CHK” in the “ADVANCED SETUP” menu to “YES” (p.127).
The cable connecting the unit and TV (or playback device) is defective.
If there is no problem with the connection, replace with another cable.
The input video signal (resolution) is not supported by the unit.
To check the information about the current video signal (resolution), use “Video Signal”
in the “Information” menu (p.124). For information about video signals supported by
the unit, see “HDMI signal compatibility” (p.147).
No video.
No video from the playback device (connected to the
unit with HDMI).
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
The playback device that supports HDCP 2.2 is connected to other than
the HDMI 1-3 jack.
Refer to the instruction manuals for the TV and check the TV’s specifications.
If you want to play back contents that require HDCP 2.2-compatible devices, both the TV
and playback device must support HDCP 2.2.
To play back contents that require HDCP 2.2-compatible devices, connect the playback
device to the HDMI 1-3 jack (p.30).
The number of devices connected to the HDMI OUT jack is over the limit. Disconnect some of the HDMI devices.
The menu of the unit is not displayed on the TV.
Another input source is selected on the TV.
Switch the TV input to display the video from the unit (HDMI OUT jack).
En
135
FM/AM radio
Problem
Cause
Remedy
There is multi-path interference.
Adjust the FM antenna height or orientation, or place it in a different location.
Your area is too far from the FM station transmitter.
Set “FM Mode” in the “Option” menu to “Mono” to select monaural FM radio reception
(p.93).
FM radio reception is weak or noisy.
Use an outdoor FM antenna. We recommend using a sensitive multi-element antenna.
AM radio reception is weak or noisy.
The noises may be caused by fluorescent lamps, motors, thermostats, or It is difficult to completely eliminate noise. It may be reduced by using an outdoor AM
other electrical equipment.
antenna.
Select the station manually (p.63).
Your area is too far from the FM station transmitter.
Use an outdoor antenna. We recommend using a sensitive multi-element antenna.
Adjust the AM antenna orientation.
Radio stations cannot be selected automatically.
Select the station manually (p.63).
The AM radio signal is weak.
Use an outdoor AM antenna. Connect it to the ANTENNA (AM) jack together with the
supplied AM antenna.
AM radio stations cannot be registered as presets.
Auto Preset is for registering FM radio stations only. Register AM radio stations manually
(p.64).
Auto Preset has been used.
En
136
Bluetooth
Problem
Cause
Remedy
The Bluetooth function of the unit is disabled.
A Bluetooth connection cannot be established.
No sound is produced, or the sound is interrupted
during playback.
Enable the Bluetooth function (p.117).
Another Bluetooth device is already connected to the unit.
Terminate the current Bluetooth connection and then establish a new connection (p.67).
The unit and the Bluetooth device are too far apart.
Move the Bluetooth device closer to the unit.
There is a device (such as microwave oven and wireless LAN) that
outputs signals in the 2.4 GHz frequency band nearby.
Move the unit away from those devices.
The Bluetooth device does not support A2DP.
Use a Bluetooth device that supports A2DP.
The connection information registered on the Bluetooth device is not
working for some reason.
Delete the connection information on the Bluetooth device, and then establish a
connection between the Bluetooth device and the unit again (p.67).
The volume of the Bluetooth device is set too low.
Turn up the volume of the Bluetooth device.
The Bluetooth device is not set to send audio signals to the unit.
Switch the audio output of the Bluetooth device to the unit.
The Bluetooth connection has been terminated.
Establish a Bluetooth connection between the Bluetooth device and the unit again
(p.67).
The unit and the Bluetooth device are too far apart.
Move the Bluetooth device closer to the unit.
There is a device (such as microwave oven and wireless LAN) that
outputs signals in the 2.4 GHz frequency band nearby.
Move the unit away from those devices.
USB and network
Problem
Cause
Remedy
The USB device is not connected to the USB jack securely.
Turn off the unit, reconnect your USB device, and turn the unit on again.
The file system of the USB device is not FAT16 or FAT32.
Use a USB device with FAT16 or FAT32 format.
The data in the USB device is protected by the encryption.
Use a USB device without an encryption function.
The network parameters (IP address) have not been obtained properly.
Enable the DHCP server function on your router and set “DHCP” in the “Setup” menu to
“On” on the unit (p.115). If you want to configure the network parameters manually,
check that you are using an IP address which is not used by other network devices in
your network (p.115).
The unit does not detect the USB device.
Folders and files in the USB device cannot be viewed.
The network feature does not function.
The unit cannot connect to the Internet via a wireless
router (access point).
The wireless router (access point) is turned off.
Turn on the wireless router.
The unit and the wireless router (access point) are too far apart.
Place the unit and the wireless router (access point) closer to each other.
There is an obstacle between the unit and the wireless router (access
point).
Move the unit and the wireless router (access point) in a location where there are no
obstacles between them.
En
137
Problem
Cause
Remedy
Microwave ovens or other wireless devices in your neighborhood might
disturb the wireless communication.
Turn off these devices.
Wireless network is not found.
Access to the network is restricted by the firewall settings of the wireless
Check the firewall setting of the wireless router (access point).
router (access point).
Configure the sharing setting and select the unit as a device to which music contents are
shared (p.72).
The media sharing setting is not correct.
Some security software installed on your PC is blocking the access of the
Check the settings of security software installed on your PC.
unit to your PC.
The unit does not detect the PC.
The files in the PC cannot be viewed or played back.
The Internet radio cannot be played.
The iPhone does not recognize the unit when using
AirPlay.
The unit and PC are not in the same network.
Check the network connections and your router settings, and then connect the unit and
the PC to the same network.
The MAC address filter is enabled on the unit.
In “MAC Address Filter” in the “Setup” menu, disable the MAC address filter or specify
the MAC address of your PC to allow it to access to the unit (p.116).
The files are not supported by the unit or the media server.
Use the file format supported by both the unit and the media server. For information
about the file formats supported by the unit, see “Playing back music stored on media
servers (PCs/NAS)” (p.72).
The selected Internet radio station is currently not available.
There may be a network problem at the radio station, or the service may have been
stopped. Try the station later or select another station.
The selected Internet radio station is currently broadcasting silence.
Some Internet radio stations broadcast silence at certain of times of the day. Try the
station later or select another station.
Access to the network is restricted by the firewall settings of your
network devices (such as the router).
Check the firewall settings of your network devices. The Internet radio can be played
only when it passes through the port designated by each radio station. The port number
varies depending on the radio station.
The unit is connected to a multiple SSID router.
Access to the unit might be restricted by the network separation function on the router.
Connect the iPhone to the SSID which can access the unit.
The unit and smartphone/tablet are not in the same network.
Check the network connections and your router settings, and then connect the unit and
smartphone/tablet to the same network.
The MAC address filter is enabled on the unit.
In “MAC Address Filter” in the “Setup” menu, disable the MAC address filter or specify
the MAC address of your smartphone/tablet to allow it to access to the unit (p.116).
It may not be possible depending on the condition of the network.
Update the firmware via the network again or use a USB memory device (p.128).
The application for smartphone/tablet “AV
CONTROLLER” does not detect the unit.
Firmware update via the network is failed.
En
138
Error indications on the front display
Message
Access denied
Cause
Remedy
Access to the PC is denied.
Configure the sharing settings and select the unit as a device to which music contents are shared (p.72).
The unit cannot access the USB device.
Turn off the unit and reconnect your USB device. If the problem persists, try another USB device.
Make sure your router and modem are turned on.
Access error
There is a problem with the signal path from the network to the unit.
Check the connection between the unit and your router (or hub) (p.35).
Check SP Wires
The speaker cables short circuit.
Twist the bare wires of the cables firmly and connect to the unit and speakers properly.
Internal Error
An internal error has occurred.
Contact the nearest authorized Yamaha dealer or service center.
No content
There are no playable files in the selected folder.
Select a folder that contains files supported by the unit.
No device
The unit cannot detect the USB device.
Turn off the unit and reconnect your USB device. If the problem persists, try another USB device.
Please wait
The unit is preparing for connecting to the network.
Wait until the message disappears. If the message stays more than 3 minutes, turn off the unit and turn it on
again.
RemID Mismatch
The remote control IDs of the unit and the remote control are not
identical.
Change the remote control ID of the unit or the remote control (p.126).
Unable to play
The unit cannot play back the songs stored on the PC for some reason.
Check if the format of files you are trying to play is supported by the unit. For information about the formats
supported by the unit, see “Playing back music stored on media servers (PCs/NAS)” (p.72). If the unit supports
the file format, but still cannot play back any files, the network may be overloaded with heavy traffic.
USB Overloaded
An overcurrent is flowing through the USB device.
Turn off the unit and reconnect your USB device. If the problem persists, try another USB device.
Version error
Firmware update is failed.
Update the firmware again.
Update failed.
Firmware update is failed.
Press STRAIGHT and select a firmware updating method, then press INFO to update the firmware again.
En
139
Glossary
This section explains the technical terms used in this manual.
DSD (Direct Stream Digital)
DSD (Direct Stream Digital) technology stores audio signals on digital storage media, such as SACD (Super Audio
CDs). The signals are stored at a high-frequency sampling rate (such as 2.8224 MHz and 5.6448 MHz). The highest
Audio information (audio decoding format)
frequency response is equal to or higher than 100 kHz, with a dynamic range of 120 dB. This technology offers better
audio quality than that used for CDs.
Dolby Atmos
DTS 96/24
Introduced first in the cinema, Dolby Atmos brings a revolutionary sense of dimension and immersion to the Home
DTS 96/24 is a compressed digital audio format that supports 5.1-channel and 96 kHz/24-bit audio. This format
Theater experience. Dolby Atmos is an adaptable and scalable object based format that reproduces audio as
remains fully compatible with the existing multichannel audio systems that support DTS Digital Surround. This
independent sounds (or objects) that can be accurately positioned and move dynamically throughout the 3
technology is used for music DVDs, etc.
dimensional listening space during playback. A key ingredient of Dolby Atmos is the introduction of a height plane of
DTS Dialog Control
sound above the listener.
DTS Dialog Control allows you to boost the dialog. This can be useful in noisy environments to help make the dialog
Dolby Atmos Stream
more intelligible. People with impaired hearing may also benefit. Note that the content creator may disable the use
Dolby Atmos content will be delivered to your Dolby Atmos enabled AV receiver via Dolby Digital Plus or Dolby
of this feature in the mix, so that DTS Dialog Control may not always be available. Note that updates to your AVR may
TrueHD on Blu-ray Disc, downloadable files and streaming media. A Dolby Atmos stream contains special metadata
add more functionality to DTS Dialog Control or increase the range of the feature.
that describes the positioning of sounds within the room. This object audio data is decoded by a Dolby Atmos AV
DTS Digital Surround
receiver and scaled for optimum playback through Home Theater speaker systems of every size and configuration.
DTS Digital Surround is a compressed digital audio format developed by DTS, Inc. that supports 5.1-channel audio.
Dolby Digital
This technology is used for audio on most DVD discs.
Dolby Digital is a compressed digital audio format developed by Dolby Laboratories, Inc. that supports 5.1-channel
DTS-ES
audio. This technology is used for audio on most DVD discs.
DTS-ES creates total 6.1-channel audio from 5.1-channel sources that are recorded with DTS-ES. This decoder adds
Dolby Digital Plus
a surround back sound to the original 5.1-channel sound. In the DTS-ES Matrix 6.1 format, a surround back sound is
Dolby Digital Plus is a compressed digital audio format developed by Dolby Laboratories, Inc. that supports
recorded in the surround channels, and in the DTS-ES Discrete 6.1 format, a discrete surround back channel is
7.1-channel audio. Dolby Digital Plus remains fully compatible with the existing multichannel audio systems that
recorded.
support Dolby Digital. This technology is used for audio on BD (Blu-ray discs).
DTS Express
Dolby Enabled Speaker
DTS Express is a compressed digital audio format that supports 5.1-channel audio and allows a higher compression
A convenient alternative to speakers built into the ceiling, products utilizing Dolby speaker technology employ the
rate than the DTS Digital Surround format developed by DTS, Inc. This technology is developed for audio streaming
ceiling above you as a reflective surface for reproducing audio in the height plane above the listener. Dolby enabled
services on the Internet and secondary audio on BD (Blu-ray discs).
speakers feature a unique upward firing driver and special signal processing that can be built into a conventional
DTS-HD High Resolution Audio
speaker, or a standalone speaker module, minimally impacting the overall speaker system footprint while providing
DTS-HD High Resolution Audio is a compressed digital audio format developed by DTS, Inc. that supports
an immersive listening experience during Dolby Atmos and Dolby surround playback.
7.1-channel and 96 kHz/24-bit audio. DTS-HD High Resolution Audio remains fully compatible with the existing
Dolby Surround
multichannel audio systems that support DTS Digital Surround. This technology is used for audio on BD (Blu-ray
Dolby surround is a next generation surround technology that intelligently up mixes stereo; 5.1 and 7.1 content for
discs).
playback through your surround speaker system. Dolby surround is compatible with traditional speaker layouts, as
DTS-HD Master Audio
well as Dolby Atmos enabled playback systems that employ in-ceiling speakers or products with Dolby speaker
DTS-HD Master Audio is an advanced lossless audio format developed to offer a high-definition home theater
technology.
experience with the quality of the studio master by DTS, Inc. DTS-HD Master Audio can carry up to eight channels of
Dolby TrueHD
96 kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio) simultaneously. This technology is used for audio on
Dolby TrueHD is an advanced lossless audio format developed by Dolby Laboratories, Inc. to offer a high-definition
BD (Blu-ray discs).
home theater experience with the quality of the studio master. Dolby TrueHD can carry up to eight channels of 96
DTS Neo:6
kHz/24-bit audio (up to six channels of 192 kHz/24-bit audio) simultaneously. This technology is used for audio on BD
DTS Neo:6 enables 6-channel playback from 2-channel sources. There are two modes available: “Music mode” for
(Blu-ray discs).
music sources and “Cinema mode” for movie sources. This technology provides discrete full-bandwidth matrix
channels of surround sound.
En
140
Audio information (others)
DTS:X
DTS:X is the next generation object-based, multi-dimensional audio technology from DTS. Unbound from channels,
DTS:X conveys the fluid movement of sound to create an incredibly rich, realistic and immersive soundscape - in
Bi-amplification connection (Bi-amp)
front of, behind, beside and above the audience - more accurately than ever before. DTS:X offers the ability to
A bi-amplification connection uses two amplifiers for a speaker. When you use the bi-amplification connection, the
automatically adapt the audio to the speaker layout that best fits the space, from a television’s built-in speakers to
unit drives the tweeter and woofer in a speaker with the discrete amplifiers. As a consequence, the tweeter and
a home surround theater system to a dozen or more speakers in a commercial cinema. Immerse yourself at
woofer provide clear audio signal without the interference.
www.dts.com/dtsx
LFE (Low Frequency Effects) 0.1 channel
FLAC
This channel reproduces low-frequency bass signals and has a frequency range from 20 Hz to 120 Hz. This channel is
FLAC is a file format for lossless audio data compression. FLAC is inferior to lossy compressed audio formats in
added to the channels for all bands with Dolby Digital or DTS to enhance low frequency audio effects. This channel
compression rate but provides higher audio quality.
is labeled 0.1 because it is limited to only low frequency audio.
MP3
Lip sync
One of the compressed digital audio format used by MPEG. With psychoacoustic technologies, this compression
Video output sometimes lags behind audio output due to the complexity of signal processing caused by an increase
method achieves a high compression rate. Reportedly, it is capable of compressing data quantity by about 1/10
in video signal capacity. Lip sync is a technique for automatically correcting the timing lag between audio and video
maintaining a certain level of audio quality.
output.
MPEG-4 AAC
An MPEG-4 audio standard. It is used for mobile telephones, portable audio players, and audio streaming services on
Internet because it allows a high compression rate of data while maintaining better audio quality than MP3.
Neural:X
Neural:X is the latest downmixing/upmixing and spatial remapping technology from DTS. It is built in to DTS:X to
provide upmix of Neural:X-encoded and non-encoded (PCM) data. In DTS:X for AVRs and Sound Bars, Neural:X can
produce up to 11.x channels.
PCM (Pulse Code Modulation)
PCM is a signal format under which an analog audio signal is digitized, recorded, and transmitted. This technology is
the basis of all other audio format. This technology is used as a lossless audio format called Linear PCM for audio on
a variety of media, including CDs and BD (Blu-ray discs).
Sampling frequency/Quantization bit
Sampling frequency and quantization bits indicate the quantity of information when an analog audio signal is
digitized. These values are noted as in the following example: “48 kHz/24-bit”.
• Sampling frequency
Sampling frequency (the number of times the signal is sampled per second) is called the sampling rate. When the
sampling frequency is higher, the range of frequencies that can be played back are wider.
• Quantization bit
The number of quantization bits indicate the degree of accuracy when converting the sound level into a numeric
value. When the number of quantized bits is higher, the expression of the sound level is more accurate.
WAV
Windows standard audio file format, which defines the method of recording the digital data obtained by converting
audio signals. By default, the PCM method (no compression) is used, but you can also use other compression
methods.
WMA (Windows Media Audio)
One of the compressed digital audio formats developed by Microsoft Corporation. With psychoacoustic
technologies, this compression method achieves a high compression rate. Reportedly, it is capable of compressing
data quantity by about 1/20 maintaining a certain level of audio quality.
En
141
HDMI and video information
Yamaha technologies
Component video signal
CINEMA DSP (Digital Sound Field Processor)
With the component video signal system, the video signal is separated into the Y signal for luminance and the Pb and
Since the surround sound systems were originally designed for use in movie theaters, their effect is best experienced
Pr signals for chrominance. Color can be reproduced more faithfully with this system because each of these signals
in a theater that has many speakers designed for acoustic effects. Since home conditions (such as room size, wall
is independent.
material, and number of speakers) can differ so widely, it is inevitable that there are differences in the sound that you
Composite video signal
hear. Based on a wealth of actually measured data, CINEMA DSP, Yamaha’s original DSP technology provides the
audiovisual experience of a movie theater in your own home.
With the composite video signal system, color, brightness, and synchronization data signals are combined and
transmitted with a single cable.
CINEMA DSP 3D
Deep Color
The actually measured sound field data contain the information of the height of the sound images. CINEMA DSP 3D
mode achieves the reproduction of the accurate height of the sound images so that it creates the accurate and
Deep Color is a technology that HDMI specification supports. Deep Color increases the number of available colors
intensive 3D sound fields in a listening room.
within the boundaries defined by the RGB or YCbCr color space. Conventional color systems process the color using
8 bits. Deep Color processes the color with 10, 12, or 16 bits. This technology allows HDTVs and other displays to
Compressed Music Enhancer
increase from millions of colors to billions of colors and eliminate on-screen color banding for smooth tonal
The Compressed Music Enhancer feature compensates for missing harmonics in compression music formats (such
transitions and subtle gradations between colors.
as MP3). As a result, this technology provides improved performance for the overall sound system.
HDCP
SILENT CINEMA
HDCP (High-bandwidth Digital Content Protection) is a digital copy protection form that prevents copying of digital
Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones
contents as it travels across connections (such as HDMI).
have been set for each sound program, so that accurate representations of all the sound programs can be enjoyed
HDMI
on headphones.
HDMI (High-Definition Multimedia Interface) is the world-wide standard interface for digital audio/video signal
Virtual CINEMA DSP
transmission. This interface transmits both digital audio and digital video signals using a single cable without any
Virtual CINEMA DSP allows the system to virtually reproduce the sound field of the surround speakers with front left
loss. HDMI complies with HDCP (High-bandwidth Digital Content Protection) and provides a secure audio/video
and right speakers. Even if the surround speakers are not connected, the unit creates the realistic sound field in a
interface. For further information on HDMI, visit the HDMI website at http://www.hdmi.org/.
listening room.
x.v.Color
Virtual CINEMA FRONT
“x.v.Color” is a technology that the HDMI specification supports. It is a more extensive color space than sRGB and
Virtual CINEMA FRONT allows the system to virtually reproduce the sound field of the surround speakers with front
allows the expression of colors that were not hitherto possible. While remaining compatible with the color gamut of
surround speakers. Even if the surround speakers placed in the front, the unit creates the realistic sound field in a
sRGB standards, “x.v.Color” expands the color space, and thus can produce more vivid, natural images.
listening room.
Virtual Presence Speaker (VPS)
Virtual Presence Speaker allows the system to virtually reproduce the height of the 3D sound field without front
Network information
presence speakers. Even if the front presence speakers are not connected, the unit creates the 3D sound field in your
room.
SSID
Virtual Surround Back Speaker (VSBS)
SSID (Service Set Identifier) is a name that identifies a particular wireless LAN access point.
Virtual Surround Back Speaker allows the system to virtually reproduce the sound field of the surround back
Wi-Fi
speakers. Even if the surround back speakers are not connected, the unit adds a sense of depth to the rear sound filed
Wi-Fi (Wireless Fidelity) is a technology that allows an electronic device to exchange data or connect to the Internet
of CINEMA DSP.
wirelessly using radio waves. Wi-Fi offers the advantage of eliminating the complexity of making connections with
network cables by using wireless connection. Only products that complete Wi-Fi Alliance interoperability tests can
carry the “Wi-Fi Certified” trademark.
WPS
WPS (Wi-Fi Protected Setup) is a standard established by the Wi-Fi Alliance, which allows easy establishment of a
wireless home network.
En
142
File formats
Supported devices and file formats
For information about specifications of each file, refer to the instruction manual of your
This section explains the devices and file formats supported by the unit.
recording device or consult file’s help.
Supported devices
⬛ USB/PC (NAS)
For information about specifications of each device, refer to the instruction manual of it.
Sampling
frequency
Quantization
bitrate
(kHz)
(bit)
WAV *
32/44.1/48/88.2/96/
176.4/192
MP3
32/44.1/48
⬛ Bluetooth device
File
• The unit supports Bluetooth devices that support A2DP or AVRCP.
• A Bluetooth device may not be detected by the unit or some feature may not be compatible,
depending on the model.
⬛ USB devices
• The unit supports USB mass storage class devices (e.g., flash memories or portable audio
players) using FAT16 or FAT32 format.
• Do not connect devices other than USB mass storage class devices (such as USB chargers or
USB hubs), PCs, card readers, an external HDD, etc.
storage device.
The number of
channels
Gapless
playback
16/24
⏤
2
✔
⏤
8 to 320
2
⏤
WMA
32/44.1/48
⏤
8 to 320
2
⏤
MPEG-4 AAC
32/44.1/48
⏤
8 to 320
2
⏤
FLAC
32/44.1/48/88.2/96/
176.4/192
16/24
⏤
2
✔
ALAC
32/44.1/48/88.2/96
16/24
⏤
2
✔
AIFF
32/44.1/48/88.2/96/
176.4/192
16/24
⏤
2
✔
DSD
2.8 MHz/5.6 MHz
1
⏤
2
⏤
• USB devices with encryption cannot be used.
• Some features may not be compatible, depending on the model or manufacturer of the USB
Bitrate
* Linear PCM format only
X
⬛ AirPlay
• To play back FLAC files stored on a PC or NAS, you need to install server software that supports sharing of FLAC
files via DLNA on your PC or use a NAS that supports FLAC files.
AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac with OS X Mountain
• Digital Rights Management (DRM) contents cannot be played back.
Lion or later, and PC with iTunes 10.2.2 or later.
Made for.
iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone
5s, iPhone 5c, iPhone 5, iPhone 4s
iPad Pro (9.7″ and 12.9″), iPad mini 4, iPad Air 2, iPad mini 3, iPad Air, iPad mini 2, iPad mini,
iPad (3rd and 4th generation), iPad 2
iPod touch (5th and 6th generation)
(as of March 2017)
En
143
Video conversion table
Video signal flow
Video signals input from a video device to the unit are output
to a TV as shown below.
X
• You can select the resolution and the aspect ratio applied to HDMI-output video processing in “Video Mode” (p.112) in the “Setup” menu.
• The unit does not convert 480-line and 576-line video signals interchangeably.
HDMI out
Resolution
Video device
The unit
480i/576i
480p/576p
720p
1080i
1080p
4K
m
m
m
m
m
m
m
m
m
m
m
720p
m
m
m
m
1080i
m
m
m
m
1080p/50, 60 Hz
m
m
m
m
m
m
TV
480i/576i
480p/576p
HDMI in
HDMI out
HDMI
HDMI
HDMI
COMPONENT
VIDEO in
Y
AV 1
AV 1
COMPONENT VIDEO
COMPONENT VIDEO
PB
PR
Y
PB
HDMI
HDMI in
PR
VIDEO in
VIDEO
1080p/24 Hz
VIDEO
m
4K
COMPONENT VIDEO in
480i/576i
m
m
m
m
m
m
VIDEO in
480i/576i
m
m
m
m
m
m
m: Available
En
144
Information on HDMI
(Example)
HDMI Control
HDMI Control
This section explains the functions related to HDMI and its signal compatibility.
HDMI Control
Turns on and displays
video from the playback
device
Playback starts
HDMI Control allows you to operate external devices via HDMI. If you connect a TV that
Press SCENE1
supports HDMI Control to the unit with an HDMI cable, you can control the unit (such as power
To use HDMI Control, you need to perform the following HDMI Control link setup after
and volume) with TV remote control operations. You can also control playback devices (such
connecting the TV and playback devices.
as HDMI Control-compatible BD/DVD players) connected to the unit with an HDMI cable.
For details on settings and operating your TV, refer to the instruction manual for the TV.
For details on connections, see “Connecting a TV” (p.29) and “Connecting video devices (such
Y
as BD/DVD players)” (p.30).
This setup is required every time you add a new HDMI Control-compatible device to your system.
Operations available from the TV’s remote control
1
2
• Standby synchronization
• Volume control including mute
• Switching to input audio from the TV when the TV input is switched to its built-in tuner
Turn on the unit, TV, and playback devices.
Configure the settings of the unit.
• Switching to input video/audio from the selected playback device
1
Switch the TV input to display video from the unit.
• Switching between audio output devices (the unit or TV speaker)
2
Press ON SCREEN.
(Example)
ON
SCREEN
HDMI Control
HDMI Control
ON SCREEN
Cursor keys
ENTER
ENTER
RETURN
Playback device
also turns off
OPTION
The unit turns off
(standby)
3
Turn off the TV
Operations available from the unit’s remote control
• Starting playback on the playback device and turning on the TV with a scene selection (p.56)
• Switching the TV input to display the on-screen menu (when ON SCREEN is pressed)
• Controlling the playback device (playback and menu operations) using the external device
operation keys
En
145
DISPLAY
Use the cursor keys to select “Setup” and press ENTER.
4
Y
Use the cursor keys (e/r) to select “HDMI”.
• If HDMI Control does not work properly, try unplugging the TV in Step 2 and plugging in the TV again in Step 3.
It may solve the problem. Also, HDMI Control may not work if the number of connected devices exceeds the
limit. In this case, disable HDMI Control on the devices not in use.
• If the unit is not synchronized to the TV’s power operations, check the priority of the audio output setting on
the TV.
• We recommend using TV and playback devices from the same manufacturer so that HDMI Control works more
effectively.
• We do not assure the operation of all HDMI Control-compatible devices.
3
5
6
Use the cursor keys (q/w) to select “HDMI Control” and press ENTER.
7
Press ON SCREEN.
Audio Return Channel (ARC)
Use the cursor keys to select “On”.
ARC allows you to input TV audio to the unit with the HDMI cable which transmits video signal
to the TV.
Check the following after the HDMI Control settings.
Enable HDMI Control on the TV and playback devices (such as HDMI
1
2
Control-compatible BD/DVD players).
4
Turn off the main power of the TV and then turn off the unit and playback
If you cannot hear the TV audio, check the following:
Turn on the unit and playback devices and then turn on the TV.
• “ARC” (p.114) in the “Setup” menu is set to “On”.
• The HDMI cable is connected to the ARC-compatible HDMI jack (HDMI jack marked
Switch the TV input to display the video from the unit.
“ARC”) on the TV.
Some HDMI jack on the TV is not compatible with ARC. For details, refer to the instruction
Check the followings.
manual for the TV.
On the unit: The input to which the playback device is connected is selected. If not, select
Y
the input source manually.
• If the audio is interrupted while using ARC, set “ARC” (p.114) in the “Setup” menu to “Off” and use a digital
On the TV: The video from the playback device is displayed.
8
Check that the input source of the unit will be automatically switched to
“AUDIO 1” and the TV audio will be played back on the unit.
devices.
5
6
7
Select a TV program with the TV remote control.
optical cable to input TV audio to the unit (p.30).
• When using ARC, connect a TV with an HDMI cable that supports ARC.
Check that the unit is properly synchronized with the TV by turning off the TV
X
or adjusting the TV volume with the TV remote control.
“AUDIO 1” is set as TV audio input at the factory. If you have connected any external device to the AUDIO 1 jacks,
use “TV Audio Input” (p.113) in the “Setup” menu to change the TV audio input assignment. To use the SCENE
function (p.56), you also need to change the input assignment for SCENE2.
En
146
HDMI signal compatibility
• When CPPM copy-protected DVD-Audio is played back, video/audio signals may not be
output, depending on the type of the DVD player.
• The unit is not compatible with HDCP-incompatible HDMI or DVI devices. For details, refer to
the instruction manual for each device.
• To decode audio bitstream signals on the unit, set the input source device appropriately so
that the device outputs the bitstream audio signals directly (does not decode the bitstream
signals on the playback device). For details, refer to the instruction manual for the playback
device.
En
147
Trademarks
Bluetooth protocol stack (Blue SDK)
Copyright 1999-2014 OpenSynergy GmbH
Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos,
Dolby Surround, and the double-D symbol are trademarks of Dolby
Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under license
from DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol,
DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS,
Inc. in the United States and/or other countries. © DTS, Inc. All Rights
Reserved.
All rights reserved. All unpublished rights reserved.
Yamaha Eco-Label is a mark that certifies products of high environmental
performance.
The terms HDMI, the HDMI Logo, and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
“SILENT CINEMA” is a trademark of Yamaha Corporation.
x.v.Color™
“x.v.Color” is a trademark of Sony Corporation.
Google Noto Fonts (Version 1.001)
Copyright © 2012 Google Inc. All rights reserved.
Licensed under the Apache License, Version 2.0 (the “License”);
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
Supports iOS 7 or later for setup using Wireless Accessory Configuration.
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an
electronic accessory has been designed to connect specifically to iPod,
iPhone, or iPad, respectively, and has been certified by the developer to
meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance
with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone, or iPad may
affect wireless performance.
iTunes, AirPlay, iPad, iPhone, iPod, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries.
DLNA™ and DLNA CERTIFIED™ are trademarks or registered trademarks of
Digital Living Network Alliance. All rights reserved. Unauthorized use is
strictly prohibited.
Windows™
Windows is a registered trademark of Microsoft Corporation in the United
States and other countries.
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an “AS IS” BASIS, WITHOUT
WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
Explanations regarding GPL
Internet Explorer, Windows Media Audio and Windows Media Player are
either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Android™ Google Play™
This product utilizes GPL/LGPL open-source software in some
sections. You have the right to obtain, duplicate, modify, and
redistribute this open-source code only. For information on
GPL/LGPL open source software, how to obtain it, and the
GPL/LGPL license, refer to the Yamaha Corporation website
Android and Google Play are trademarks of Google Inc.
(http://download.yamaha.com/sourcecodes/musiccast/).
iPad Air and iPad mini are trademarks of Apple Inc.
App Store is a service mark of Apple Inc.
The Wi-Fi CERTIFIED™ Logo is a certification mark of Wi-Fi Alliance®.
The Wi-Fi Protected Setup™ Identifier Mark is a certification mark of Wi-Fi
Alliance®.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is
under license.
MusicCast is a trademark or registered trademark of Yamaha Corporation.
En
148
Specifications
Input jacks
HDMI
USB
• Analog Audio
• 4K UltraHD Video (include 4K/60, 50Hz 10/12bit), 3D Video, ARC
(Audio Return Channel), HDMI Control (CEC), Auto Lip Sync, Deep
Color, “x.v.Color”, HD audio playback, Selectable HDMI input in
HDMI standby mode, 21:9 Aspect Ratio, BT.2020 Colorimetry, HDR
Compatible
• Capable of Mass Storage Class USB Memory
Audio x 5 (VIDEO AUX, AV 2, AUDIO 4-5, PHONO)
• Digital Audio (Supported frequencies: 32 kHz to 96 kHz)
Optical x 2 (AUDIO 1-2)
Coaxial x 2 (AUDIO 3, AV 1)
• Video
Composite x 1 (AV 2)
Component x 1 (AV 1)
• HDMI Input
HDMI x 6 (HDMI 1-5, VIDEO AUX)
• Other
USB x 1 (USB2.0)
NETWORK x 1 (100Base-TX/10Base-T)
Output jacks
• Analog Audio
– Speaker Out x 9 (7 ch) (FRONT L/R, CENTER, SURROUND L/R,
EXTRA SP 1 L/R*1, EXTRA SP 2 L/R*2)
• Video Format (Repeater Mode)
– VGA
• Current Supply Capacity: 1 A
Bluetooth
• Sink Function
Source Device to AVR (ex. Smartphone/Tablet)
• Source Function
– 480i/60 Hz
AVR to Sink Device (ex. Bluetooth Headphone)
– 576i/50 Hz
• Capable of Play/Stop Operation from Sink Device
– 480p/60 Hz
• Bluetooth Version ...........................................................Ver. 2.1+EDR
– 576p/50 Hz
• Supported Profile
– 720p/60 Hz, 50 Hz
Sink Function..................................................................A2DP, AVRCP
– 1080i/60 Hz, 50 Hz
Source Function .............................................................A2DP, AVRCP
– 1080p/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
– 4K/60 Hz, 50Hz, 30 Hz, 25 Hz, 24 Hz
• Audio Format
• Supported Codec
Sink Function........................................................................ SBC, AAC
Source Function ............................................................................ SBC
– Dolby Atmos
• Wireless Output .......................................................Bluetooth Class 2
– Dolby TrueHD
• Radio Frequency (Operational Frequency)....2402 MHz to 2480 MHz
*1 Note: Assignment is possible
– Dolby Digital Plus
• Maximum Output Power (E.I.R.P)...................... 3.91 dBm (2.46 mW)
[F.PRESENCE, ZONE2]
– Dolby Digital
• Maximum Communication Distance................................ 10 m (33 ft)
*2 Note: Assignment is possible
– DTS:X
[SURROUND BACK, ZONE2, BI-AMP]
– DTS-HD Master Audio
Network
– Subwoofer Out x 2 (SUBWOOFER 1-2, mono)
– DTS-HD High Resolution Audio
– ZONE2 OUT x 1
– DTS Express
– Headphone x 1
– DTS
• HDMI Output
HDMI OUT x 1
Other jacks
• YPAO MIC x 1
• REMOTE IN x 1
• Compatible with DLNA ver. 1.5
• AirPlay supported
• Internet Radio
– DSD 2.8MHz 2-ch to 6-ch
– PCM 2-ch to 8-ch (Max. 192 kHz/24-bit)
• Content Protection: HDCP compatible
(HDMI 1–3: HDCP 2.2 compatible)
• Link Function: CEC supported
• REMOTE OUT x 1
TUNER
• TRIGGER OUT x 1
• Analog Tuner
• PC Client Function
• Wi-Fi function
– Capable of WPS by PIN Method and Push-Button-Method
– Capable of sharing with iOS devices by wireless connection
– Capable of Direct Connection with Mobile Device
– Available Security Method: WEP, WPA2-PSK (AES), Mixed Mode
– Wireless LAN Standards: IEEE 802.11 b/g/n
– Radio Frequency (Operational Frequency): 2412 MHz to 2472 MHz
[U.K. and Europe models]
– Maximum Output Power (E.I.R.P): 17.42 dBm (55.2 mW)
FM/AM with Radio Data System x 1 (TUNER)
[Other models]
FM/AM x 1 (TUNER)
En
149
Compatible Decoding Formats
• Decoding Format
– Dolby Atmos
– Dolby TrueHD, Dolby Digital Plus
– Dolby Digital
– DTS:X
– DTS-HD Master Audio, DTS-HD High Resolution Audio,
DTS Express
– DTS 96/24, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1
• Tone Control Characteristics
• Damping Factor
Front L/R, 20 Hz to 20 kHz, 8 Ω ........................................ 100 or more
• Input Sensitivity / Input Impedance
PHONO (1 kHz, 100 W/8 Ω) ............................................ 3.5 mV/47 kΩ
AV 2 etc. (1 kHz, 100 W/8 Ω) .......................................... 200 mV/47 kΩ
(fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F. (Front, Center, Surround, Surround Back) ..............12 dB/oct.
• Output Level / Output Impedance
ZONE2 OUT .................................................................. 470 mV/1.7 kΩ
• Rated Output Power (2-channel driven)
(20 Hz to 20 kHz, 0.06% THD, 8 Ω)
Front L/R .............................................................................90 W+90 W
(1 kHz, 0.9% THD, 8 Ω)
Treble Turnover........................................................................3.5 kHz
AV 2 etc. (1 kHz, 0.5% THD, Effect On)......................................... 2.3 V
• Post Decoding Format
Audio Section
Treble Boost/Cut .................................... ±6 dB/0.5 dB Step at 20 kHz
PHONO (1 kHz, 0.1% THD) ........................................................60 mV
SUBWOOFER ....................................................................... 1 V/1.2 kΩ
– DTS Neo:6 Music, DTS Neo:6 Cinema
Bass Turnover............................................................................350 Hz
• Filter Characteristics
• Maximum Input Signal
– DTS Digital Surround
– Dolby Surround
Bass Boost/Cut ......................................... ±6 dB/0.5 dB Step at 50 Hz
• Headphone Jack Rated Output / Impedance
AV 2 etc. (1 kHz, 50 mV, 8 Ω) ......................................... 100 mV/560 Ω
• Frequency Response
AV 2 etc. to Front (10 Hz to 100 kHz) ..................................... +0/-3 dB
• RIAA Equalization Deviation
PHONO ...................................................................................0±0.5 dB
• Total Harmonic Distortion
L.P.F. (Subwoofer)...............................................................24 dB/oct.
Video Section
• Video Signal Type...................................................NTSC/PAL/SECAM
• Video Signal Level
Composite ........................................................................ 1 Vp-p/75 Ω
Component
Y ..................................................................................... 1 Vp-p/75 Ω
Pb/Pr........................................................................... 0.7 Vp-p/75 Ω
• Video Maximum Input Level .................................... 1.5 Vp-p or more
FM Section
[U.S.A. and Canada models]
PHONO to Speaker Out (FRONT) (20 Hz to 20 kHz, 1 V)
........................................................................................ 0.02% or less
Front L/R .........................................................................105 W+105 W
AV 2 etc. to Front (Pure Direct)
[U.S.A. and Canada models] ...........................87.5 MHz to 107.9 MHz
Center..........................................................................................105 W
(20 Hz to 20 kHz, 50 W, 8 Ω) ........................................... 0.06% or less
[Taiwan, Brazil, Asia and General models]
...................................................87.5/87.50 MHz to 108.0/108.00 MHz
Surround L/R ..................................................................105 W+105 W
Surround Back L/R .........................................................105 W+105 W
• Rated Output Power (1-channel driven)
(1 kHz, 0.9% THD, 8 Ω)
Front L/R ............................................................................... 125 W/ch
Center.................................................................................... 125 W/ch
Surround L/R ........................................................................ 125 W/ch
Surround Back L/R ............................................................... 125 W/ch
• Signal to Noise Ratio (IHF-A Network)
PHONO (Input Shorted 35 mV, Speaker Out [FRONT])
.......................................................................................96 dB or more
AV 2 etc. (Pure Direct) (Input 1 kΩ Shorted, Speaker Out)
.....................................................................................110 dB or more
• Residual Noise (IHF-A Network)
Front L/R (Speaker Out)................................................ 150 μV or less
• Channel Separation
PHONO (Input Shorted, 1 kHz/10 kHz) .............60 dB/55 dB or more
Front L/R [U.K. and Europe models].................................... 150 W/ch
AV 2 etc. (Input 1 kΩ Shorted, 1 kHz/10 kHz)
............................................................................70 dB/50 dB or more
Front L/R ............................................................................ 150 W/ch
Center ................................................................................ 150 W/ch
Surround L/R ..................................................................... 150 W/ch
[U.K. and Europe models]...........................87.50 MHz to 108.00 MHz
[Other models] ............................................87.50 MHz to 108.00 MHz
• 50 dB Quiet Sensitivity (IHF, 1 kHz, 100% MOD.)
Mono .............................................................................3 μV (20.8 dBf)
• Signal to Noise Ratio (IHF)
Mono ........................................................................................... 69 dB
Stereo.......................................................................................... 67 dB
(1 kHz, 0.9% THD, 4 Ω)
• Maximum Effective Output Power (1 kHz, 10% THD, 6 Ω/8 Ω)
• Tuning Range
• Volume Control
Main Zone............................. MUTE, -80 dB to +16.5 dB (0.5 dB Step)
Zone2.................................... MUTE, -80 dB to +10.0 dB (0.5 dB Step)
Surround Back L/R ............................................................ 150 W/ch
• Dynamic Power (IHF)
Front L/R (8/6/4/2 Ω) ........................................... 125/165/190/235 W
En
150
• Harmonic Distortion (IHF, 1 kHz)
Mono ............................................................................................ 0.5%
Stereo........................................................................................... 0.6%
• Antenna Input.......................................................... 75 Ω unbalanced
AM section
• Tuning Range
[U.S.A. and Canada models] .............................. 530 kHz to 1710 kHz
[Taiwan, Brazil, Asia and General models]
............................................................ 530/531 kHz to 1710/1611 kHz
[U.K. and Europe models] .................................. 531 kHz to 1611 kHz
[Other models].................................................... 531 kHz to 1611 kHz
• Reference Dimensions (W x H x D) (with wireless antenna upright)
.................................435 x 234 x 378 mm (17-1/8” x 9-1/4” x 14-7/8”)
• Weight....................................................................... 10.0 kg (22.0 lbs)
* The contents of this manual apply to the latest specifications as of the
publishing date. To obtain the latest manual, access the Yamaha
website then download the manual file.
General
• Power Supply
[U.S.A. and Canada models] ...................................... AC 120 V, 60 Hz
[Brazil and General models]
.................................................. AC 110 to 120/220 to 240 V, 50/60 Hz
[Korea model] ............................................................. AC 220 V, 60 Hz
[Australia model] ........................................................ AC 240 V, 50 Hz
[U.K. and Europe models] .......................................... AC 230 V, 50 Hz
[Asia model] ................................................ AC 220 to 240 V, 50/60 Hz
• Power Consumption
[U.S.A. and Canada models] ......................................................400 W
[Brazil, Asia and General models]................................................270 W
[Other models]............................................................................300 W
• Standby Power Consumption
HDMI Control Off, Standby Through Off.....................................0.1 W
HDMI Control ON/Standby through AUTO HDMI no signal
and no CEC for 8 hours ................................................................0.4 W
HDMI Control On, Standby Through On (No Signals) ................1.1 W
Network Standby On
Wired.........................................................................................1.6 W
Wi-Fi ..........................................................................................1.6 W
Wireless Direct..........................................................................1.8 W
Bluetooth Standby On ................................................................1.6 W
HDMI Control On, Standby Through On (No Signals),
Network Standby On (Wireless Direct) .......................................2.4 W
• Maximum Power Consumption
[Taiwan, Brazil, Asia and General models]................................590 W
• Dimensions (W x H x D)
................................. 435 x 171 x 378 mm (17-1/8” x 6-3/4” x 14-7/8”)
* Including legs and protrusions
En
151
Yamaha Global Site
http://www.yamaha.com/
Yamaha Downloads
http://download.yamaha.com/
Manual Development Group
© 2017 Yamaha Corporation
Published 03/2017 NV-B0
YJ202A0/EN
Download PDF

advertising