Router BVRD2M - Baldwin Boxall
Router
BVRD2M
Certified to BSEN54
The BVRD2M DSP-controlled router is wellestablished and has been installed in many
prestigious sites Worldwide.
VIGIL 2
FEATURES:
• DSP control.
• Eight electronically balanced inputs. Inputs one and two
are configurable with ‘all call’ processor bypass and are
normally reserved for fire microphone(s). All inputs have
both independent priority and level settings.
• Up to fifteen priority levels are available. If two concurrent
routes are set at the same priority they will be treated on a
‘first come first served’ basis. Priorities are changeable.
• Three band parametric plus bass and treble equalisation
on all inputs (with limiter/compressor), enhancing the
intelligibility of the system.
• ‘All call’ failsafe emergency message generator (twenty
second EPROM).
• Seven electronically balanced audio outputs with ten
band parametric equalisation and audio delay of up to
one second.
• Fully monitored surveillance at either 30Hz or 20kHz
(faults are recorded in the history log). All inputs, outputs
and DSP messages can be aurally monitored through a
loudspeaker on the front panel.
• Built-in realtime clock enables detailed logging and
reporting, including detected faults. Indicates time,
date, month and year. Also used for night time volume
reduction, timed message trigger and to control external
inputs. The history log can be accessed via the USB2 port
on the front panel.
• Six flash stored (57 second) messages with independent
level, surveillance and timing. (For longer, non-critical
messages, up to three can be combined.) Settings and
messages are changeable (password protected) via the
USB2 port.
• Nine selectable chimes / pre-announcement tones of up
to eight seconds in length.
• Expandable with BVRD2S (slave router) and CANBUS
modules.
VOICE ALARM
PUBLIC ADDRESS
•
•
•
•
•
•
Up to 126 EVAS routers can be networked using fibre or
copper to produce a truly sophisticated digital VA network.
Message synchronisation, even on a decentralised
system.
Ambient noise sensing.
Amplifier changeover (one in ten).
Two RS485 ports for networking, microphones, etc.
Zone grouping and barring on BVRD voice alarm
controller.
HARDWARE FACILITIES:
Audio:
• 8 x electronically balanced line -20dB audio inputs (inputs
1 and 2 with processor bypass).
• ‘All call’ failsafe emergency message generator (20
second EPROM) in the event of DSP failure.
• 7 x electronically balanced 0dBM audio outputs.
• 2 x opto-coupled sounder circuit programmable inputs
from the fire detection system.
• 6 x analogue voltage sensing inputs for monitored input
access, ambient noise sensors, remote volume controls.
• 3 x contact inputs for unmonitored zone access or PTT.
Control Outputs:
• 6 x NPN collector outputs 40V @ 100mA for busy, etc.
• 1 x volt free relay changeover contact for common fault.
Serial Ports:
• 2 x RS485 half-duplex ports for communicating to control
microphones, fire detection systems, network control,
fault reporting.
• 1 x front panel USB2 port to configure the system, fault
diagnostics, fault reporting, message download, etc.
Specifications:
Audio input and output processing using DSP analogue devices ADSP2116 operating at 100MHz.
AUDIO INPUTS
AUDIO OUTPUTS
Input sensitivity
80mV (-20dB) to 3V (+12dB)
Nominal output level
0.775V (0dB)
Frequency response
-3 dB @ 30Hz and 20kHz
Max output level
Signal to noise ratio
Better than 70dB
1.5V (+6dBM) @ 400 ohms –
source = 400 ohms
Phantom power
12V
Frequency response
-3dB @ 30Hz & 20kHz
Output to noise ratio
Better than -85dB
Three band parametric equalisation
Frequency
50Hz, 63Hz, 80Hz, 100Hz, 125Hz, 160Hz,
200Hz, 250Hz, 315Hz, 400Hz, 500Hz,
630Hz, 800Hz, 1kHz, 1.25kHz, 1.6kHz,
2kHz, 2.5kHz, 3.15kHz, 4kHz, 5kHz,
6.3kHz, 8kHz, 10kHz, 12.5kHz, 16kHz
Bandwidth
0.05oct, 0.1oct, 0.2oct, 0.33oct, 0.5oct,
0.66oct, 1oct & 2oct
Lift and cut
+ 12dB in 1dB steps
Low filter
Frequency
250Hz, 315Hz, 400Hz, 500Hz, 630Hz,
800Hz, 1kHz, 1.2kHz, 1.6kHz, 2kHz,
2.5kHz
Slope
3dB/oct & 6dB/oct
Lift and cut
+ 12dB in 1dB steps
High filter
Frequency
500Hz, 630Hz, 800Hz, 1kHz, 1.25kHz,
1.6kHz, 2kHz, 2.5kHz, 3.15kHz, 4kHz,
5kHz
Lift and cut
+ 12dB in 1dB steps
High pass filter
Frequency
100Hz, 150Hz, 200Hz, 250Hz, 300Hz
Slope
18dB/oct, 12dB/oct, 6dB/oct
Compressor
Ratio
1.4:1, 2:1, 4:1, 8:1 & limiter
Attack
0-99mS
Release
0-999mS
Ten band parametric equalisation
Frequency
50Hz, 63Hz, 80Hz, 100Hz, 125Hz, 160Hz,
200Hz, 250Hz, 315Hz, 400Hz, 500Hz,
630Hz, 800Hz, 1kHz, 1.25kHz, 1.6kHz,
2kHz, 2.5kHz, 3.15kHz, 4kHz, 5kHz,
6.3kHz, 8kHz, 10kHz, 12.5kHz, 16kHz
Bandwidth
0.05oct, 0.1oct, 0.2oct, 0.33oct, 0.5oct,
0.66oct, 1oct & 2oct
Lift and cut
+ 12dB in 1dB steps
Low filter
Frequency
250Hz, 315Hz, 400Hz, 500Hz, 630Hz,
800Hz, 1kHz, 1.25kHz, 1.6kHz, 2kHz,
2.5kHz
Slope
3dB/oct & 6dB/oct
Lift and cut
+ 12dB in 1dB steps
High filter
Frequency
500Hz, 630Hz, 800Hz, 1kHz, 1.25kHz,
1.6kHz, 2kHz, 2.5kHz, 3.15kHz, 4kHz,
5kHz
Lift and cut
+ 12dB in 1dB steps
Audio delay
Selectable from 0 to 1 second
Front panel
Monitor speaker to listen to inputs or outputs
Common fault indicator, sounder and fault accept button
LCD display 40x2 characters, backlit, Rotary encoder to ease
configuration, setting levels, entering text, etc.
Messages flash PROM
Storage medium flash PROM (non-volatile) 57 seconds
POWER
Frequency response
-3dB @ 50Hz & 18kHz
DC requirements
Signal to noise ratio
Better than 65dB
22V-35V @ 500mA
Baldwin Boxall Communications Ltd
Wealden Industrial Estate, Farningham Road,
Crowborough, East Sussex, TN6 2JR, United Kingdom
T: +44 (0) 1892 664422 F: +44 (0) 1892 663146
E: [email protected]
W: www.baldwinboxall.co.uk
WE RESERVE THE RIGHT TO CHANGE THE TECHNICAL SPECIFICATION WITHOUT PRIOR NOTICE. DOC NO: 1.0001.08.16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement