Yamaha RSio64 Owner's manual

Yamaha RSio64 Owner's manual
English
Deutsch
取扱説明書
EN
DE
FR
ES
IT
RU
PT
JA
AUDIO INTERFACE
日本語
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manuale di istruzioni
Руководство пользователя
Manual do Proprietário
Português
Русский
Italiano
Español
Français
I/O RACK
The above warning is located on the top of the unit.
L’avertissement ci-dessus est situé sur le dessus de l’unité.
Explanation of Graphical Symbols
Explication des symboles
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une « tension
dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions
importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.
IMPORTANT SAFETY
INSTRUCTIONS
PRÉCAUTIONS CONCERNANT LA SÉCURITÉ
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
8
9
10
11
12
13
14
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
(UL60065_03)
Lire ces instructions.
Conserver ces instructions.
Tenir compte de tous les avertissements.
Suivre toutes les instructions.
Ne pas utiliser ce produit à proximité d’eau.
Nettoyer uniquement avec un chiffon propre et sec.
Ne pas bloquer les orifices de ventilation. Installer l’appareil conformément aux instructions du fabricant.
Ne pas installer l’appareil à proximité d’une source de chaleur comme
un radiateur, une bouche de chaleur, un poêle ou tout autre appareil (y
compris un amplificateur) produisant de la chaleur.
Ne pas modifier le système de sécurité de la fiche polarisée ou de la
fiche de terre. Une fiche polarisée dispose de deux broches dont une
est plus large que l’autre. Une fiche de terre dispose de deux broches
et d’une troisième pour le raccordement à la terre. Cette broche plus
large ou cette troisième broche est destinée à assurer la sécurité de
l’utilisateur. Si la fiche équipant l’appareil n’est pas compatible avec
les prises de courant disponibles, faire remplacer les prises par un
électricien.
Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas
piétinés ni coincés, en faisant tout spécialement attention aux fiches,
prises de courant et au point de sortie de l’appareil.
Utiliser exclusivement les fixations et accessoires spécifiés par le
fabricant.
Utiliser exclusivement le chariot, le stand, le trépied, le support ou la table recommandés par le
fabricant ou vendus avec cet appareil. Si l’appareil est posé sur un chariot, déplacer le chariot
avec précaution pour éviter tout risque de chute
et de blessure.
Débrancher l’appareil en cas d’orage ou lorsqu’il
doit rester hors service pendant une période prolongée.
Confier toute réparation à un personnel qualifié. Faire réparer l’appareil s’il a subi tout dommage, par exemple si la fiche ou le cordon d’alimentation est endommagé, si du liquide a coulé ou des objets sont
tombés à l’intérieur de l’appareil, si l’appareil a été exposé à la pluie ou
à de l’humidité, si l’appareil ne fonctionne pas normalement ou est
tombé.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
(UL60065_03)
2
Owner’s Manual
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications
not expressly approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a
reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the
instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Compliance
with FCC regulations does not guarantee that interference will
not occur in all installations. If this product is found to be the
source of interference, which can be determined by turning the
unit “OFF” and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(class B)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party :
Address :
Telephone :
Type of Equipment :
Model Name :
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620
714-522-9011
Audio Interface
RSio64-D
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may
cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(FCC DoC)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this
mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW : EARTH
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with
the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in
the plug which is marked by the letter E or by the safety earth symbol
or colored
GREEN or GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked
with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
(3 wires)
In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.
In Norway: Apparatet må tilkoples jordet stikkontakt.
In Sweden: Apparaten skall anslutas till jordat uttag.
(class I hokuo)
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로
하며, 모든 지역에서 사용할 수 있습니다.
(class b korea)
Owner’s Manual
3
Contents
Troubleshooting . . . . . . . . . . . . . . . 21
Messages
PRECAUTIONS. . . . . . . . . . . . . . . . . . .5
Introduction
8
Features ....................................................... 8
Precautions for Rack Mounting .................... 8
Firmware Updates........................................ 8
Controls and Functions
9
22
Error Messages ........................................... 22
Warning Messages ..................................... 23
Information Messages ................................ 23
Specifications . . . . . . . . . . . . . . . . 166
Dimensions . . . . . . . . . . . . . . . . . . 167
Block Diagram . . . . . . . . . . . . . . . 168
Front Panel .................................................. 9
Rear Panel.................................................. 12
Connections
14
Installing a Mini-YGDAI card ...................... 14
About Dante .............................................. 14
Notes Regarding the Use of
Network Switches ................................. 15
About Dante Controller ............................. 15
Connecting AC Power................................ 15
Power on and off ....................................... 15
Various settings
Specifying the RSio64-D’s word clock ...........18
Specifying the audio routing ........................16
Specifying the ID that
distinguishes the RSio64-D ......................10
Specifying the UNIT ID range .......................10
Specifying how the IP address is set..............10
Specifying the type of
connection to the Dante network ............11
Initializing the RSio64-D ...............................20
Specifying the audio routing
16
Editing the user pattern ............................. 17
About R Remote V4 ................................... 17
About the number of
input/output channels........................... 17
Word Clock
18
Selecting a word clock source .................... 18
About word clock ...................................... 18
SRC (Sampling Rate Converter). . . .18
Other functions
19
Remote control .......................................... 19
IDENTIFY ................................................... 19
Panel lock .................................................. 19
Initializing the RSio64-D............................. 20
Updating the RSio64-D’s
hardware settings.................................. 20
If you are using the card’s SRC................... 20
4
Owner’s Manual
Specifying the SRC word clock .....................11
Included items (please check)
• Owner’s manual
• Power cord
PA_en_4 1/2
PRECAUTIONS
PLEASE READ CAREFULLY
BEFORE PROCEEDING
Please keep this manual in a safe place for
future reference.
WARNING
Always follow the basic precautions listed below to
avoid the possibility of serious injury or even death
from electrical shock, short-circuiting, damages, fire
or other hazards. These precautions include, but are
not limited to, the following:
Fire warning
• Do not put burning items, such as candles, on the unit.
A burning item may fall over and cause a fire.
If you notice any abnormality
• When one of the following problems occur, immediately
turn off the power switch and disconnect the electric plug
from the outlet. Then have the device inspected by Yamaha
service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the device.
- There is a sudden loss of sound during use of the device.
• If this device should be dropped or damaged, immediately
turn off the power switch, disconnect the electric plug from
the outlet, and have the device inspected by qualified
Yamaha service personnel.
Power supply/power cord
• Do not place the power cord near heat sources such as
heaters or radiators, and do not excessively bend or
otherwise damage the cord, place heavy objects on it, or
place it in a position where anyone could walk on, trip over,
or roll anything over it.
• Only use the voltage specified as correct for the device.
The required voltage is printed on the name plate of the
device.
• Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the
one you purchased, the included power cord may not be
compatible. Please check with your Yamaha dealer.
• Check the electric plug periodically and remove any dirt or
dust which may have accumulated on it.
CAUTION
Always follow the basic precautions listed below to
avoid the possibility of physical injury to you or
others, or damage to the device or other property.
These precautions include, but are not limited to, the
following:
Power supply/power cord
• When removing the electric plug from the device or an
outlet, always hold the plug itself and not the cord. Pulling
by the cord can damage it.
• When setting up the device, make sure that the AC outlet
you are using is easily accessible. If you feel that a
malfunction has occurred, immediately turn off the power,
unplug the power cord plug from the electrical outlet, and
also disconnect the connected power supply from the EXT
DC INPUT jack. Even when the power switch is turned off,
as long as the power cord is not unplugged from the wall
AC outlet, the device will not be disconnected from the
power source.
• Remove the electric plug from the outlet when the device is
not to be used for extended periods of time, or during
electrical storms.
• Be sure to connect to an appropriate outlet with a
protective grounding connection. Improper grounding can
result in electrical shock, damage to the device(s), or even
fire.
• Do not block the vents. This device has ventilation holes at
the front/sides to prevent the internal temperature from
becoming too high. In particular, do not place the device
on its side or upside down. Inadequate ventilation can
result in overheating, possibly causing damage to the
device(s), or even fire.
Do not open
• This device contains no user-serviceable parts. Do not
open the device or attempt to disassemble the internal
parts or modify them in any way. If it should appear to be
malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Water warning
• Do not expose the device to rain, use it near water or in
damp or wet conditions, or place on it any containers (such
as vases, bottles or glasses) containing liquids which might
spill into any openings. If any liquid such as water seeps
into the device, turn off the power immediately and unplug
the power cord from the AC outlet. Then have the device
inspected by qualified Yamaha service personnel.
Location
• Do not place the device in an unstable position where it
might accidentally fall over.
• When installing the device:
- Do not cover it with any cloth.
- Do not install it on a carpet or rug.
- Make sure the top surface faces up; do not install on its
sides or upside down.
- Do not use the device in a confined, poorly-ventilated
location.
Inadequate ventilation can result in overheating, possibly
causing damage to the device(s), or even fire.
• Do not place the device in a location where it may come
into contact with corrosive gases or salt air. Doing so may
result in malfunction.
• Before moving the device, remove all connected cables.
• Never insert or remove an electric plug with wet hands.
Owner’s Manual
5
PA_en_4 2/2
• When setting up the device, make sure that the AC outlet
you are using is easily accessible. If some trouble or
malfunction occurs, immediately turn off the power switch
also disconnect the unit from the power supply that is
connected to the EXT DC INPUT jack. Even when the
power switch is turned off, electricity is still flowing to the
product at the minimum level. When you are not using the
product for a long time, make sure to unplug the power
cord from the wall AC outlet.
• If the device is mounted in an EIA standard rack, carefully
read the section “Precautions for Rack Mounting” on page
8. Inadequate ventilation can result in overheating,
possibly causing damage to the device(s), malfunction, or
even fire.
Connections
• Before connecting the device to other devices, turn off the
power for all devices. Before turning the power on or off for
all devices, set all volume levels to minimum.
Maintenance
• Periodically inspect and clean the air filter of the front panel
ventilation opening (page 11). Dust and dirt can seriously
degrade the effectiveness of the cooling fan and result in
malfunction or fire.
• Remove the power plug from the AC outlet when cleaning
the device.
NOTICE
To avoid the possibility of malfunction/ damage to the product,
damage to data, or damage to other property, follow the
notices below.
 Handling and maintenance
• Do not use the device in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise.
• Do not expose the device to excessive dust or vibration, or
extreme cold or heat (such as in direct sunlight, near a
heater, or in a car during the day), in order to prevent the
possibility of panel disfiguration, unstable operation, or
damage to the internal components.
• Do not place vinyl, plastic or rubber objects on the device,
since this might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not
use paint thinners, solvents, cleaning fluids, or chemicalimpregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic
changes in ambient temperature—when the device is
moved from one location to another, or air conditioning is
turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason
to believe that condensation might have occurred, leave
the device for several hours without turning on the power
until the condensation has completely dried out.
• Always turn the power off when the device is not in use.
Handling caution
• Do not insert your fingers or hands in any gaps or openings
on the device (vents).
• Avoid inserting or dropping foreign objects (paper, plastic,
metal, etc.) into any gaps or openings on the device (vents,
etc.) If this happens, turn off the power immediately and
unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.
• Do not rest your weight on the device or place heavy
objects on it, and avoid use excessive force on the buttons,
switches or connectors.
Yamaha cannot be held responsible for damage caused
by improper use or modifications to the device, or data
that is lost or destroyed.
6
Owner’s Manual
Information
 About this manual
• The illustrations as shown in this manual are for instructional purposes only.
• The company names and product names in this manual
are the trademarks or registered trademarks of their
respective companies.
The model number, serial number, power requirements, etc., may be found on or
near the name plate, which is at the top of the unit. You should note this serial
number in the space provided below and retain this manual as a permanent
record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
(rear_en_01)
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical
and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection
points, in accordance with your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
(weee_eu_en_01)
European Models
Purchaser/User Information specified in EN55103-1:2009 and EN55103-2:2009.
Inrush Current: 1.0A (on initial switch-on)
1.0A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
Owner’s Manual
7
Introduction
Introduction
Precautions for Rack
Mounting
Thank you for choosing the Yamaha RSio64-D audio
interface.
To take full advantage of the superior functions and
performance offered by the RSio64-D, and to enjoy years of
trouble-free use, be sure to read this owner’s manual
carefully before operation.
This unit is rated for operation at ambient temperatures
ranging from 0 to 40 degrees Celsius. When mounting the
unit with other RSio unit(s) or other device(s) in an EIA
standard equipment rack, internal temperatures can
exceed the specified upper limit, resulting in impaired
performance or failure. When rack mounting the unit,
always observe the following requirements to avoid heat
buildup:
Features
The RSio64-D is an interface that can be used as a router
and format converter between Dante and Mini-YGDAI
cards.
This allows Mini-YGDAI cards that support a wide variety
of input/output formats and processing to be connected to
a Dante network, meeting the needs of various types of
systems including broadcast, live, recording, and postproduction. In addition, the settings of the RSio64-D can
be fully controlled from a CL or QL series console.
• A wide variety of Mini-YGDAI cards can be used,
including processing cards as well as input/output cards.
• When mounting the unit in a rack with devices such as
power amplifiers that generate a significant amount of
heat, leave more than 1U of space between the RSio and
other equipment. Also either leave the open spaces
uncovered or install appropriate ventilating panels to
minimize the possibility of heat buildup.
• To ensure sufficient airflow, leave the rear of the rack
open and position it at least 10 centimeters from walls or
other surfaces. If you’ve installed a fan kit, there may be
cases in which closing the rear of the rack will produce a
greater cooling effect. Refer to the rack and/or fan unit
manual for details.
• Each MY slot provides an SRC (Sampling Rate
Converter) to allow digital connection between differing
word clock routes.
Firmware Updates
• Seven different widely usable routing patterns are preset,
including routing between Mini-YGDAI cards. Matrix
patching from R Remote V4 or a CL/QL console.
This product enables you to update the unit firmware to
improve operations, add functions, and correct possible
malfunctions. The following two types of firmware are
available for the unit:
• EXT DC INPUT supports redundant power supplies.
• Dante redundancy (primary/secondary) is supported.
NOTE
Before you install Mini-YGDAI cards in slots 1–4, you must
check the Yamaha website to determine whether the card is
compatible with the RSio64-D, and to verify the total number
of Yamaha or third-party cards that can be installed in
combination with that card.
Yamaha website:
http://www.yamahaproaudio.com/
• Unit’s firmware
• Dante module firmware
Firmware updates are performed from R Remote V4.
Details on updating the firmware are available on the
following website:
http://www.yamahaproaudio.com/
For information on updating the unit, refer to the firmware
update guide available on the website.
NOTE
It is necessary to update other devices depending on the
version of each device in the Dante network. For details,
refer to the firmware compatibility available on the Yamaha
website.
http://www.yamahaproaudio.com/
8
Owner’s Manual
Controls and Functions
Controls and Functions
Front Panel
r t
y
o !0
we
q SLOT 1–4 [LOCK] indicators
These indicate the word clock status of slots 1–4. The
indicator is lit green if operation is normal.
Unlit
Green (lit)
LOCK
Green
(flashing)
SYNC
ERROR
Red (lit)
UNLOCK
Red
(flashing)
WRONG
WORD
CLOCK
No card is installed in the slot, or an unsupported card is installed.
This indicates that a clock synchronized with
the clock source selected by the WORD
CLOCK select key is being input from the card.
If an external device is connected to the corresponding slot, input/output is occurring correctly between that device and the RSio64-D.
If the sampling frequency is close, this status
is shown in some cases even if not synchronized.
A valid clock is being input from the card, but is
not synchronized with the clock source
selected by the WORD CLOCK select key. If
an external device is connected to the corresponding slot, input/output is not occurring
correctly between that device and the RSio64D. Input/output will occur correctly if SRC is
turned ON.
A valid clock is not being input from the card. If
an external device is connected to the corresponding slot, input/output cannot occur correctly between that device and the RSio64-D.
The frequency of the clock source selected by
the WORD CLOCK select key is outside the
range of operating frequencies of the card
installed in the slot. Either set the frequency of
the clock source to be within the operating
range of the card, or turn SRC on. In the case
of an analog card, turning SRC on makes the
card operate at the RSio64-D’s internal frequency of 48 kHz.
1 2 3 4 5 6 7 8
u
ON
q
ON
!3
!3
1 2 3 4
i
!1 !2
NOTE
• If the SLOT1–4 [LOCK] indicators and the SLOT1–4 [SRC]
indicators and all WORD CLOCK indicators simultaneously
flash red at startup, overcurrent has occurred in a MiniYGDAI card, or a malfunctioning Mini-YGDAI card is
installed. Turn off the power and remove the card that is
causing the problem.
• If the SLOT1–4 [LOCK] indicators and the SLOT1–4 [SRC]
indicators alternately flash red at startup, the hardware
settings of the RSio64-D need to be updated (page 20).
• If the SLOT1–4 [LOCK] indicators sequentially light green in
the order of 1–4 at startup, the clocks of the slots are
synchronizing. This may take several tens of seconds.
w SLOT 1–4 [SRC] indicators
These indicate the SRC (Sampling Rate Converter)
status of slots 1–4.
Unlit
SRC is off.
Green (lit)
SRC is on, and the clock selected by the SRC
WCLK DIP switch is being input correctly.
Red (lit)
SRC is on, but an appropriate clock is not
being input. It may be that the clock selected
by the SRC WCLK DIP switch is not being
input, or is outside the operating range. Either
turn SRC off, or change the setting of the DIP
switch.
NOTE
The SRC clock sent to a Mini-YGDAI card installed in a slot
is selected by the SRC WCLK DIP switch (page 11).
e SLOT 1–4 [SRC] keys
For each slot, these turn SRC on/off for the slot’s input
as well as output.
Owner’s Manual
9
Controls and Functions
r WORD CLOCK select key
Selects the word clock source of the RSio64-D.
WORD CLOCK [WCLK IN] indicator
WORD CLOCK [SLOT1 1/2] indicator
WORD CLOCK [DANTE] indicator
These indicate the status of the RSio64-D’s word clock
source.
WCLK IN
This is lit if the RSio64-D is using the word
clock that is being input from the rear panel
[WORD CLOCK IN] connector. This flashes if
there is no valid word clock input*1.
This is lit if the channel 1/2 word clock of slot 1
is being used. This flashes if there is no valid
word clock input*1. The channel 7/8 word clock
SLOT1 1/2
is used when using the MY8-AEB*2. If the
SRC on the MY8-AE96S is in use, you will be
unable to use the input signal as word clock.
DANTE
u Device setting DIP switches
These switches specify startup settings for the device.
Details are given below.
Making the setting
Turn off the power before you change these DIP
switch settings. The setting is applied the next time
you turn the power on. If you change the setting
while the power is on, the changed setting is not
applied until the power is turned off and on again.
(This note does not apply to switch 6.)
The switch illustrations indicate the setting state as
follows.
Switch
State
Switch is in the upward (OFF) position.
This is lit if the Dante network’s word clock*3
is being used. (If no valid Dante signal is being
input, the clock generated by the internal
Dante module is used.)
Switch is in the downward (ON) position.
*1 When this is flashing, the unit uses the Dante word clock to
operate and perform input/output.
ON
*2 In order to use MY8-AEB, set AE  RSVD switch to the
RSVD position.
*3 If you want to change the frequency of the Dante word
clock, use Dante Controller.
t ROUTING [PATTERN] rotary switch
This selects the RSio64-D’s internal audio routing
pattern from seven preset patterns and one user
pattern. Setting the rotary switch to 1–7 selects preset
routing patterns 1–7, and setting it to 0 selects the user
routing pattern.
Making the setting
You can select the routing pattern even when the
power is on. Your selection is applied three seconds
after you switch the routing pattern.
UNIT ID
IP SETTING
SECONDARY PORT
START UP MODE
• Switch 1 (UNIT ID)
This switch setting determines whether the [UNIT ID]
setting will range from hexadecimal 00 to 0F or from 10
to 1F.
Switch
NOTE
The routing pattern does not change if you select 8–F.
y SETUP [UNIT ID] rotary switch
Specifies an ID that identifies this device on the Dante
network. If there are multiple Dante-compatible
devices from Yamaha that require an ID setting
connected to the same network, set a different ID for
each device.
Making the setting
Turn off the power before you change the setting of
this rotary switch. The setting is applied the next
time you turn the power on. If you change the
setting while the power is on, the changed setting is
not applied until the power is turned off and on
again.
Owner’s Manual
Setting
Description
1
UNIT ID =
00-0F
The UNIT ID setting range is 00
to 0F.
1
UNIT ID =
10-1F
The UNIT ID setting range is 10
to 1F.
• Switch 2/Switch 3 (IP SETTING)
These specify the method of setting the IP address used
when communicating with an external device such as R
Remote V4. When connecting the RSio64-D to a
computer for the first time immediately after purchase,
set this to something other than STATIC IP (MANUAL).
If you want to set this to STATIC IP (MANUAL), first
specify the IP address from R Remote V4 and then
switch this setting to STATIC IP (MANUAL).
Switch
2
3
Setting
Description
AUTO IP
The Dante network automatically specifies the IP address as
169.254.XX.XX.
DHCP
The IP address assigned from
the DHCP server is used.
2
3
2
3
STATIC IP
(AUTO)
The IP address is specified as
192.168.0.xx (xx=UNIT ID).
3
STATIC IP
(MANUAL)
The IP address is specified from
an external device such as R
Remote V4.
2
10
1 2 3 4 5 6 7 8
Front Panel
NOTE
• If the network consists only of Dante devices and R Remote
V4, we recommend that you set this to AUTO IP.
• If connecting to an existing network, select DHCP as
necessary.
• If you want to use zoning to specify the IP address, or if you
want to connect to an existing network and fix the IP
address, use R Remote V4 to specify the IP address and
then set this to STATIC IP (MANUAL).
• Switch 7/Switch 8 (START UP MODE)
These switches specify the start-up mode.
Switch
7
7
• Switch 4 (SECONDARY PORT)
This switch setting determines whether the rear-panel
[SECONDARY] connector will be used for a daisy
chain or redundant network.
If this is set to [DAISY CHAIN], you can connect
multiple Dante-enabled network devices in a daisy
chain without using a network switch.
With the [REDUNDANT] setting, the [PRIMARY]
connector will be used for primary connections, and
the [SECONDARY] connector will be used for
secondary (backup) connections. This provides a
redundant connection so that if the unit is unable to
transmit signals through the [PRIMARY] connector
for some reason (e.g., due to damage or accidental
removal of the cable, or a failed network switch), the
[SECONDARY] connector will automatically take over
communications.
Switch
4
4
Settings
Description
The [SECONDARY] connector
is used for a daisy chain connection. A signal at the [PRIDAISY CHAIN
MARY] connector will be
transmitted to the next device in
the chain as is.
The [SECONDARY] connector
is used for a redundant network. It will function as backup
REDUNDANT
connection, independent of the
network to which the [PRIMARY] connector is connected.
• Switch 5
Not used. Leave these in the factory-set position
(upward).
• Switch 6
This switch position specifies the SRC to be used: one
on the main unit or one on the MY8-AE96S card. If you
are using a card other than MY8-AE96S, the SRC will
always be used on the main unit regardless of the switch
position.
NOTE
If SRC on the MY8-AE96S card is used, the input and output
of the unit’s SRC will be disabled, and the main unit’s word
clock will be used as the card’s SRC clock regardless of the
switch position.
Switch
6
6
Settings
NORMAL
CARD
Description
The main unit’s SRC is used.
The card’s SRC is used.
8
8
Settings
NORMAL
INITIALIZE
Description
Start up normally with the settings of the previous start-up.
Initialize the settings. For details
on the settings that are initialized, refer to “Initializing the
RSio64-D” (page 20).
i SRC WCLK DIP switches
These select the word clock of each slot’s SRC (SLOT/
WORD CLOCK IN). DIP switches 1–4 correspond to
SLOT 1–4. When a DIP switch is off, the word clock of
the corresponding slot is used. When a DIP switch is
on, the signal of WORDCLOCK IN is used as the SRC
word clock.
NOTE
• The setting of these DIP switches is applied three seconds
after they are switched while the power is on.
• If an analog Mini-YGDAI card is installed and the
corresponding slot’s SRC is turned on, that slot uses the
RSio64-D’s internal 48 kHz clock.
o Dante [SYSTEM] indicators
These indicate the operating status of the unit. If the
green indicator lights steadily and the red indicator
turns off, the unit is operating normally.
When power to the unit is turned ON, if the green
indicator turns off, or if the red indicator lights or
flashes, the unit is not functioning properly. In this case,
refer to “Messages” (page 22).
!0 Dante [SYNC] indicators
These indicate the sync status between the Dante
network and this unit. If the green indicator lights, the
unit is operating as a word clock slave and synching to
the word clock.
If the green indicator flashes, the unit is operating as the
word clock master.
If the unit is powered-on but the green indicator is
unlit, a malfunction has occurred. In this case, refer to
“Messages”(page 22).
Also refer to “Messages” if the orange indicator is lit or
flashing.
!1 POWER INT indicator
Indicates whether the AC IN power supply is powered.
If the power switch is off, this indicator is unlit
regardless of whether power is supplied to AC IN.
!2 POWER EXT indicator
Indicates whether the EXT DC INPUT power supply is
powered. This is lit if the EXT DC INPUT power supply
is powered. This indicator is not affected by the state of
the power switch.
!3 Cooling vents
To prevent the interior temperature from becoming
excessive, two cooling vents are provided on the front
panel. Air filters are installed inside the cooling vents to
prevent dust from entering the unit through the vents.
• Cleaning the cooling vents
After extended use, dust may accumulate on the
cooling vents, obstructing the airflow. If dust
accumulates, remove it periodically by placing a
vacuum cleaner gently over the cooling vents.
Owner’s Manual
11
Controls and Functions
Rear Panel
w
q
!0
e
t
yu
r
q [ ]/[ ] (power switch)
Turns the unit’s power (supplied from the AC IN
connector) on [ ]/off [ ]. If power is supplied from
the AC IN connector and this power switch is also on,
the front panel POWER INT indicator is lit.
CAUTION
Even when the power switch is turned off, a small amount of
current is flowing through the unit. When you are not using
the product for a long time, make sure to unplug the power
cord from the AC outlet.
NOTE
Rapidly turning the unit on and off in succession can cause
it to malfunction. After turning the unit off, wait for at least 6
seconds before turning it on again.
w AC IN connector
Connect the supplied AC power cord here. First
connect the AC power cord to the RSio unit, then insert
the power cord plug into an AC power outlet.
The supplied AC power cord features a V-lock
mechanism via a latch, which prevents the power cord
from coming off accidentally.
Insert the cable plug all the way until it locks in securely.
CAUTION
Be sure to turn the power off before connecting or
disconnecting the power cord.
Press the latch button on the plug to disconnect the
power cord.
o
i
e EXT DC INPUT connector
This is an XLR-4-32 type connector through which an
external power supply (+24V) can be provided as a
backup for the internal power supply of the RSio64-D.
CAUTION
Before connecting the external power supply, you must turn
off the power of this unit and the power of the external power
supply. Malfunctions or electrical shock may occur if you fail
to observe this caution.
NOTE
• This power supply cannot be turned on/off by the power
switch.
• If an external power supply is connected, the RSio64-D will
operate normally when the internal and external power
supplies are both on, as well as when only one of them is on.
• If both power supplies are on and one of the power supplies
fails during operation, the unit automatically switches to the
other power supply. The state of the power supply is shown
by the front panel POWER indicator.
r Grounding screw
Since the included power cord has a three-conductor
plug, this unit is appropriately grounded if the AC
outlet is grounded. In some cases, you may be able to
reduce hum and interference by connecting ground to
this screw as well.
t SLOT 1–4
Mini-YGDAI I/O cards can be installed in these slots.
Each of the four slots is equipped with an SRC.
y SLOT ACTIVE indicator
Indicates whether the slots are powered.
CAUTION
Do not insert or remove a Mini-YGDAI card if this indicator is
lit. Malfunctions or electrical shock may occur if you fail to
observe this caution.
12
Owner’s Manual
Rear Panel
u WORD CLOCK IN connector
This is a BNC connector used to receive word clock
signals. The WORD CLOCK IN connector is internally
terminated with 75Ω.
i Dante [PRIMARY] connector
Dante [SECONDARY] connector
These etherCON (RJ45) connectors allow connection
with Dante devices such as a CL series console using
standard Ethernet cables (CAT5e or better
recommended).
NOTE
• Use STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Make sure that the metal
parts of the plugs are electrically connected to the STP
cable shield by conductive tape or comparable means.
• Connect only Dante-compatible devices or Gigabit Ethernet
compatible devices (including computers).
• Cables up to 100 meters* long can be used.
* Maximum usable length varies according to the cable
used.
o Dante [PRIMARY LINK/ACT] indicator
Dante [PRIMARY 1G] indicator
Dante [SECONDARY LINK/ACT] indicator
Dante [SECONDARY 1G] indicator
Displays the transmission status with the Dante
network.
LINK/ACT
These indicators flash rapidly if the Ethernet
cables are connected properly.
1G
These indicators are lit when the Dante network is functioning as Gigabit Ethernet.
!0 Exhaust vent
The RSio64-D is equipped with a cooling fan. Air is
exhausted through this vent, so take care that it is not
blocked by any obstruction.
Exhaust vent
Owner’s Manual
13
Connections
Connections
Installing a Mini-YGDAI card
3. Align the two edges of the card with the guide
rails inside the slot, and insert the card into the
slot.
Push the card all the way into the slot until the
connector of the card is correctly inserted into the
connector inside the slot.
Before you install I/O cards in slots 1–4, you must check the
Yamaha website to determine whether the card is
compatible with the RSio64-D, and to verify the total
number of Yamaha or third-party cards that can be
installed in combination with that card.
Yamaha website:
http://www.yamahaproaudio.com/
To install an optional mini-YGDAI card, proceed as
follows.
1.
Make sure that the power is turned off.
CAUTION
Before installing a Mini-YGDAI I/O card in this unit, you must
turn off the power of this unit and the power of the external
power supply. You must also verify that the SLOT ACTIVE
indicator is unlit. Malfunctions or electrical shock may occur
if you fail to observe this caution.
2. Loosen the screws that hold the slot cover in
Card
place, and remove the slot cover.
Keep the removed slot cover and screws in a safe place.
4. Secure the card using the screws that are
attached to the card.
If the card is not secured, malfunction or faulty
operation may occur.
Slot cover
About Dante
Dante is a network audio protocol developed by Audinate.
It is designed to deliver multi-channel audio signals at
various sampling and bit rates, as well as device control
signals over a Gigabit Ethernet (GbE) network.
Visit the Audinate website for more details on Dante:
http://www.audinate.com/
More information on Dante is also posted on the Yamaha
Pro Audio website:
http://www.yamahaproaudio.com/
14
Owner’s Manual
Notes Regarding the Use of Network Switches
Notes Regarding the Use of
Network Switches
We recommend a gigabit-compatible network switch that
provides functions for controlling and monitoring the
network (such as QoS).
Do not use the EEE functionality (*) of network switches
on a Dante network.
Although mutual power consumption settings between
switches that support the EEE functionality are adjusted
automatically, there are some switches for which such
mutual settings are not adjusted correctly.
This may cause EEE to be enabled in Dante networks when
it is not appropriate, resulting in poor synchronization
performance and occasional dropouts.
Therefore we strongly recommend the following.
• If you use managed switches, please disable the EEE
functionality. Do not use switches that prevent EEE
functionality from being disabled.
• When using unmanaged switches, do not use switches
that support EEE functionality. EEE functionality cannot
be disabled for such switches.
* EEE (Energy Efficient Ethernet) is a technology that
reduces switch power consumption during periods of low
network traffic. It is also referred to as Green Ethernet and
IEEE802.3az.
Connecting AC Power
1.
Turn the unit off.
2. Connect the plug on the AC power cord to the
AC IN connector on the rear panel of the unit.
3. Connect the other side of the plug on the AC
power cord to a power supply socket.
NOTE
• When removing the AC power cord, perform these steps in
reverse.
• Press the latch button on the plug to disconnect the power
cord.
WARNING
• The RSio64-D has been designed assuming it a proper
ground connection is used. To prevent electrical shock and
damage to devices, use the included AC power cord to
create a secure ground connection. If you do not know how
to make a proper ground connection, contact your Yamaha
dealer.
• Be sure to use only the included power cord with this unit.
Use of a different power cord could result in abnormal heat
and electrical shock.
CAUTION
• Be sure to turn the power off before connecting or
disconnecting the power cord.
• Even when the power switch is turned off, a small amount of
current is flowing through the unit. When you are not using
the product for a long time, make sure to unplug the power
cord from the power supply outlet.
About Dante Controller
Dante Controller is a software application that allows
configuration and audio routing of Dante networks. Use
this application if you plan to connect or set up Danteenabled devices that do not feature RSio64-D-native
support. Please download the Dante Controller application
from the website listed below.
Please note that Dante Controller Version 3.2.1 or later
supports RSio64-D.
http://www.yamahaproaudio.com/
Power on and off
To prevent loud sounds that might harm your hearing or
damage equipment downstream, poweron each unit in the
order of the signal flow. When turning the power off,
reverse this order.
To run Dante Controller, a computer must feature a GbEcompatible Ethernet connector.
Refer to the Dante Controller owner’s manual for details on
Dante Controller.
Owner’s Manual
15
Specifying the audio routing
 PATTERN 4
The inputs and outputs of Slots 1 and 2, and Slots 3 and
4 are interconnected.
Specifying the
audio routing
The RSio64-D provides seven preset patterns of audio
routing that connect each slot to the Dante network. There
is also one user pattern (page 17) which the user can edit.
Use the front panel ROUTING
[PATTERN] rotary switch to select the
routing.
Setting the rotary switch to 1–7 selects
preset routing patterns 1–7, and setting
it to 0 selects the user routing pattern.
Making the setting
You can select the routing pattern even when the power
is on. Your selection is applied three seconds after you
switch the routing pattern.
The preset routing patterns are described below.
 PATTERN 1
Dante is connected one-to-one with each slot’s input/
output.
48k/44.1k
96k/88.2k
48k/44.1k
96k/88.2k
SLOT 1
1-16
1-8
1-16
1-8
SLOT 2
1-16
1-8
SLOT 3
1-16
1-8
17-32
9-16
Dante
33-48
17-24
SLOT 4
1-16
1-8
SLOT 1
1-16
1-8
SLOT 2
1-16
1-8
SLOT 3
1-16
1-8
SLOT 4
1-16
1-8
48k/44.1k
96k/88.2k
1-16
1-8
17-32
9-16
Dante
33-48
17-24
49-64
25-32
 PATTERN 5
Dante inputs 1–16* are distributed to the outputs of
each slot.
48k/44.1k
96k/88.2k
SLOT 1
1-16
1-8
SLOT 2
1-16
1-8
SLOT 3
1-16
1-8
SLOT 4
1-16
1-8
48k/44.1k
96k/88.2k
1-16
1-8
17-32
9-16
Dante
33-48
17-24
49-64
25-32
 PATTERN 6
Dante inputs 1–16* are distributed to the outputs of
slots 1 and 2, and Dante inputs 17–32* are distributed
to the outputs of slots 3 and 4.
48k/44.1k
96k/88.2k
SLOT 1
1-16
1-8
SLOT 2
1-16
1-8
SLOT 3
1-16
1-8
SLOT 4
1-16
1-8
48k/44.1k
96k/88.2k
1-16
1-8
17-32
9-16
Dante
33-48
17-24
49-64
25-32
49-64
25-32
 PATTERN 2
The inputs of slot 1 are distributed to the outputs of
slots 2–4.
48k/44.1k
96k/88.2k
SLOT 1
1-16
1-8
SLOT 2
1-16
1-8
SLOT 3
1-16
1-8
SLOT 4
1-16
1-8
48k/44.1k
96k/88.2k
1-16
1-8
17-32
9-16
Dante
33-48
17-24
49-64
25-32
 PATTERN 7
Dante 1–32* and slots 1–2 are connected one-to-one,
and the inputs and outputs of slots 3 and 4 are
connected respectively to each other.
48k/44.1k
96k/88.2k
SLOT 1
1-16
1-8
SLOT 2
1-16
1-8
SLOT 3
1-16
1-8
SLOT 4
1-16
1-8
48k/44.1k
96k/88.2k
1-16
1-8
17-32
9-16
Dante
33-48
17-24
49-64
25-32
*At 48/44.1 kHz
 PATTERN 3
The inputs of slot 1 are distributed to the outputs of slot
2, and the inputs of slot 3 are distributed to the outputs
of slot 4.
16
48k/44.1k
96k/88.2k
48k/44.1k
96k/88.2k
SLOT 1
1-16
1-8
SLOT 2
1-16
1-8
SLOT 3
1-16
1-8
SLOT 4
1-16
1-8
48k/44.1k
96k/88.2k
1-16
1-8
17-32
9-16
Dante
33-48
17-24
49-64
25-32
Owner’s Manual
NOTE
• If the inputs/outputs of an installed Mini-YGDAI card cannot
be assigned in 16-channel units, such as for a 4-channel or
a 8-channel card, audio routing signals from such card are
muted by the slot (e.g., if the Mini-YGDAI card is an 8channel card, channels 9–16 are muted).
• For different sampling frequencies, the channels of the
routing pattern are switched automatically, as shown above.
However if SRC is on, the number of the slot’s channels may
change, so there may be cases in which you are unable to
use the above patterns as you would like. In such cases, use
the user pattern.
For example when the sampling frequency is 88.2/96 kHz,
Dante channels 1–8, 9–16, 17–24, and 25-32 are available,
but if SRC is on for SLOT 1, and the sampling frequency of
that slot is 44.1/48 kHz, then channels 1–16 are available for
SLOT 1.
Editing the user pattern
Editing the user pattern
The user pattern lets you freely specify the routing between
Dante and the slots.
To edit the user pattern, use R Remote V4 or a CL/QL series
console.
For details, refer to the respective manuals.
About the number of input/
output channels
The number of audio input/output channels is as follows.
Slots
The slots can provide up to 64 channels (16 channels per
slot) of audio signal input/output.
About R Remote V4
This is an application that lets you view and edit the
settings of R series units such as the RSio64-D.
R Remote V4 can be downloaded from the following
website.
http://www.yamahaproaudio.com/
Frequency
Input
Output
44.1 kHz
16 ch
16 ch
48 kHz
16 ch
16 ch
88.2 kHz
8 ch
8 ch
96 kHz
8 ch
8 ch
NOTE
• If an analog Mini-YGDAI card is installed and the
corresponding slot’s SRC is turned on, that slot uses the
RSio64-D’s internal 48 kHz clock.
• If this unit’s sampling frequency is set to 88 kHz or 96 kHz,
and you want to install a Mini-YGDAI card that does not
support 88.2 kHz or 96 kHz, you should turn SRC on for that
slot. If SRC is off, audio signals will not be output.
Dante
Frequency
Input
Output
44.1 kHz
64 ch
64 ch
64 ch
48 kHz
64 ch
88.2 kHz
32 ch
32 ch
96 kHz
32 ch
32 ch
NOTE
To change the Dante clock frequency, use Dante Controller.
Owner’s Manual
17
Word Clock
Word Clock
Selecting a word clock
source
Use the WORD CLOCK select key on the front panel to
select the word clock source.
The unit’s clock is synced with the selected word clock
source.
WCLK IN
This is lit if the RSio64-D is using the word
clock that is being input from the rear panel
[WORD CLOCK IN] connector. This flashes if
there is no valid word clock input*1.
SLOT1 1/2
This is lit if the channel 1/2 word clock of slot 1
is being used. This flashes if there is no valid
word clock input*1. The channel 7/8 word clock
is used when using the MY8-AEB*2.
DANTE
This is lit if the Dante network’s word clock*3 is
being used. (If no valid Dante signal is being
input, the clock generated by the internal Dante
module is used.)
*1 When this is flashing, the unit uses the Dante word clock to
operate and perform input/output.
*2 In order to use MY8-AEB, set AE  RSVD switch to the RSVD
position.
*3 If you want to change the frequency of the Dante word clock,
use Dante Controller.
About word clock
• If you select “WCLK IN” or “SLOT1 1/2,” the unit is
automatically set to Enable Sync To External
(synchronize to an external clock). If you select
“DANTE,” Enable Sync To External is automatically
turned off.
If you select “WCLK IN” or “SLOT1 1/2,” and this unit is
a clock slave of the Dante network, the same clock should
be input to the clock master device and to this device.
You can use Dante Controller to check which device is
the current clock master.
• If the word clock signal from the selected word clock
source is cut off, the unit switches to the “DANTE”
setting (Enable Sync To External automatically turns
off), and operates with the clock frequency that is
specified by Dante.
18
Owner’s Manual
SRC (Sampling
Rate Converter)
• Even if the Mini-YGDAI card installed in a slot is not
synchronized with the Dante network, connection is
possible without having to change the respective clocks.
• The output signal from the slot synchronizes with the
clock from the slot’s input signal or with the clock that is
input via WORD CLOCK IN. However, if the card’s SRC
is enabled, the main unit’s SRC will be disabled, and
signals in sync with the main unit’s clock will be output.
Other functions
Other functions
IDENTIFY
Remote control
From a Yamaha CL/QL series console, from R Remote V4,
or from Dante Controller, you can identify a specific
RSio64-D unit from among multiple network-connected
devices. When you specify the IDENTIFY operation, all
front panel indicators on that unit except for the POWER
(INT/EXT) indicator will flash for ten seconds.
The same operations performed from the RSio64-D’s front
panel, such as turning SRC on/off, can be performed from
a device that supports remote control.
NOTE
For the latest information about remote control compatible
devices, refer to the Yamaha Pro Audio website:
http://www.yamahaproaudio.com/
Remote controllable parameters
Parameter
Description
SRC ON/OFF
Turns SRC on or off.
WORD CLOCK
Selects the source used as the master clock.
USER PATTERN
Lets you specify the user routing pattern.
DANTE PATCH*
Lets you change the Dante patch.
ROUTING PATTERN
Displays the pattern number.
SRC SOURCE CLOCK
Shows the source used by the SRC.
POWER INT/EXT
Shows the power supply status.
Panel lock
You can lock the panel to prevent unintended changes and
operations.
While the lock is engaged, all controllers on the front panel
are inoperable. To engage the lock, press and hold the
SLOT 1 and SLOT 4 [SRC] keys for at least 3 seconds. All
front panel indicators (except the power indicator) flash,
and operation is locked. To disengage the lock, press and
hold the SLOT 1 and SLOT 4 [SRC] keys for at least 3
seconds.
SYSTEM/SYNC STATUS Shows the system sync status.
DEVICE LABEL
Shows the UNIT ID/device name
(label).
* DANTE PATCH: Specifies which channels of the CL/QL series
console are input to which of the RSio64-D’s Dante 1–64 channels.
Press simultaneously for
at least three seconds
NOTE
• If you turn off the power while panel lock is engaged, panel
lock will still be engaged the next time the power is turned
on.
• Even if the front panel is locked, you can use remote control
to make changes to the settings.
Owner’s Manual
19
Other functions
Initializing the RSio64-D
To return (initialize) the internal memory to its factory-set
state, for example if you move the unit to a different
location, proceed as follows.
1.
Turn the unit off.
2. On the front panel, set device setting DIP
switch 7 down and switch 8 up (INITIALIZE).
Updating the RSio64-D’s
hardware settings
If the SLOT 1–4 [LOCK] indicators and the SLOT 1–4
[SRC] indicators are alternately flashing red and the unit
does not start up, it may be that the unit’s hardware settings
were not updated when updating the firmware. In this case,
proceed as follows to update the RSio64-D’s hardware
settings.
ON
1.
7 8
1 2 3 4 5 6 7 8
3. Turn the unit on.
Initialization begins. When initialization is completed,
the SLOT 1–4 [LOCK] and SLOT 1–4 [SRC] indicators
flash green and red alternately.
While holding down the SLOT 3 [SRC] key, turn
the power on again.
Updating of the unit’s hardware settings begins. During
the update, the SLOT 1 [LOCK] indicator and the
SLOT 1 [SRC] indicator light simultaneously. To
indicate the status during the update process, both the
[LOCK] indicator and the [SRC] indicator successively
light in the order of SLOT 2  SLOT 3  SLOT 4.
When the update is completed, the eight indicators
flash once and then return to the normal illumination
status.
4. Verify that initialization is completed, and turn
the unit off.
5. Set device setting DIP switches 7 and 8 both up
(NORMAL).
If you are using the card’s
SRC
7 8
6. Turn the unit on.
The following parameters are initialized.
Parameter
SLOT 1–4 SRC
Initialized setting
OFF
WORD CLOCK SELECT DANTE/48 kHz
USER PATTERN
Same routing settings as preset pattern 1
STATIC IP (Manual)
0.0.0.0
Panel Lock
Lock defeated
Dante patches
All off
Dante device label
Y001-Yamaha-RSio64-D-123456 (*1)
(*1) The third and fourth characters of the Dante device label
depend on device setting DIP switch 1 and the SETUP [UNIT
ID] rotary switch. The lower six digits depend on the lower six
digits of the unit’s MAC address.
* When shipped from the factory, all of the device setting DIP
switches are set to the upward position.
20
Owner’s Manual
If your card features an SRC (MY8-AE96S), you can use the
card’s SRC instead of the main unit’s SRC.
To use the card’s SRC, set device setting DIP switch 6 on the
front panel to the down position.
When this function is enabled, the [SRC] key on the front
panel of the main unit will be used to turn the card’s SRC
on or off.
• Changes made to device setting DIP switch 6 will
become effective in three seconds.
• For a slot that has a card without an SRC inserted, the
[SRC] key will turn the unit’s SRC on or off regardless of
the switch position.
Troubleshooting
Troubleshooting
Device settings and DIP switch settings are not
applied
 Turn off the power before changing the setting. If you change
The following is an abbreviated list of frequently asked
questions in the past. Please check it if you run into similar
problems and need help.
Power does not turn on, power indicator does not
light
 Connect the power cord properly (page 15).
 Turn the [POWER] switch ON. If the power still will not
come on, contact your Yamaha dealer.
SLOT 1–4 [LOCK] indicators and SLOT 1–4 [SRC]
indicators alternately flash red, and the unit does
not start up
the setting while the power is on, the changed setting is not
applied until the power is turned off and on again.
What are the computer requirements for
updating the firmware?
 For information about updating the unit, refer to the firmware update guide for each product and the following website.
http://www.yamahaproaudio.com/
Cannot update
 The problem may be solved by disabling any antivirus software and the firewall of the computer. For other details, refer
to the firmware update guide available on the website.
http://www.yamahaproaudio.com/
 The unit’s hardware settings was not updated after updating
the firmware. Alternatively, the unit’s hardware settings may
be damaged.
While holding down the SLOT 3 [SRC] key, turn the power
on again to update the unit’s hardware settings (page 20). If
the power still will not come on, contact your Yamaha dealer.
Sound is not output
 Connect the cables properly.
 Verify that a signal is being output from the corresponding
device.
 If the SLOT 1–4 [LOCK] indicator is flashing red or lit red, respecify the correct clock.
 Is the patch of the Dante network set up correctly by Dante
Controller?
 On the unit to which the RSio64-D is connected, is the word
clock set in a way that is compatible with the Dante network?
 Check whether the user pattern setting is correct.
 Check whether the routing pattern selection might be incorrect.
Audio cuts out or distorts.
 Is the slot’s input frequency selected correctly?
 If [SLOT] or [WCLK IN] is selected as the word clock source,
change it to [DANTE]. Keep in mind that if this remedies the
problem, the clocks for the Dante network and the unit will
not be synced. In this case, this unit must be acting as the
clock master for the Dante network. If this still does not solve
the problem, check the SLOT 1–4 [LOCK] indicators and the
WORD CLOCK indicators, and take the appropriate action.
For details, refer to the Dante Controller User Guide available
on the website.
http://www.yamahaproaudio.com/
Can’t operate the panel
 Could panel lock be activated?
The RSio64-D is not recognized on the Dante
network
 Does the Dante [UNIT ID] conflict with another Dante-compatible device made by Yamaha?
 Is the network switch working properly?
The problem may be solved by turning the network switch on
again.
 Is the cable defective?
The problem may be solved by replacing the cable.
What devices should I update?
 It is necessary to update multiple devices depending on the
version of each device. For details, refer to the firmware compatibility available on the website.
http://www.yamahaproaudio.com/
How can the Dante input and output signals be
patched?
 Use Dante Controller to configure the audio routing (patching) of the Dante network. For details, refer to the Dante Controller User Guide available on the website.
http://www.yamahaproaudio.com/
Is it possible to receive the input signal from
RSio64-D by a separate mixer?
 It can be configured using the Dante Controller. For details,
refer to the Dante Controller User Guide available on the
website.
http://www.yamahaproaudio.com/
In the case of a Yamaha CL/QL series unit, settings can be
made from the I/O DEVICE screen.
I want to change the RSio64-D settings from the
mixer
I want to know the devices that can remotely
configure the RSio64-D
 For details on RSio64-D remote control, refer to the following
website.
http://www.yamahaproaudio.com/
What is the latency of the Dante network?
 The latency of the Dante network can be specified using
Dante Controller. For details, refer to the manuals for each
product.
An internal error message such as “firmware
mismatch” is displayed on the device connected
to the RSio64-D.
 Make sure that each device has a compatible version. For
details, refer to the firmware compatibility information available on the website.
http://www.yamahaproaudio.com/
Owner’s Manual
21
Messages
Messages
Errors, warnings, and certain other types of information
are displayed via the RSio64-D front panel indicators.
Messages are also displayed in the Dante Controller Error
Status field.
Each indicator lights or flashes as described below:
No call-out
The indicator is off.
Light
The indicator remains lit steadily.
Flash
The indicator continues to flash.
Flash x2
The indicator flashes twice cyclically.
Flash x3
The indicator flashes three times cyclically.
The following errors affect the settings or the hardware.
However, the device will still be usable. The green
SYSTEM indicator will light, and all indicators for all I/O
channels will work normally.
In addition, certain errors will cause the red SYSTEM
indicator to light or flash.
[SYSTEM] Indicators
(green)
Lit
(green)
Error Messages
Lit
If one of the following errors has occurred, the device will
not operate. Until the error is resolved, the green SYSTEM
indicator will be turned off, and all indicators for all I/O
channels will continue to flash.
In addition, certain errors will cause the red SYSTEM
indicator to light or flash.
[SYSTEM] Indicators
(red)
Description
Flash x3
(red)
Communication
cannot occur
because the MAC
address setting
has been corrupted.
The device has
failed. Contact
your Yamaha
dealer for repair.
UNIT ID is not
unique.
Set a unique UNIT
ID number within
the Dante network.
The device’s DIP
switches are not
set correctly.
Check the DIP
switch settings,
and set them correctly.
Flash
22
(red)
(red)
Owner’s Manual
(green)
Lit
The cooling fan
has stopped.
Check that nothing is caught in the
fan. If the problem
persists, consult
your Yamaha
dealer.
The internal memory has been corrupted.
When using the
unit in [NORMAL]
mode, if the problem persists even
after turning the
power off and on
again, consult your
Yamaha dealer.
You changed the
positions of the
device setting DIP
switches or rotary
switch, or changed
the Dante settings
from Dante Controller. Therefore,
the positions of the
device setting DIP
switches do not
match the actual
Dante settings.
If the Device Lock
setting was
enabled from
Dante Controller,
disable the setting,
or check the
device setting DIP
switch positions,
and set them to
accommodate the
current situation.
Flash x3
(red)
Lit
Possible Solution
Reduce the number of flows by, for
The number of
example, using
Dante transmit
Dante Controller to
flows exceeded the
change some of
limit.
the transmit flows
to multicast.
Flash x2
Possible Solution
Lit
(red)
Lit
Flash
An internal error
has occurred.
Flash x2
(red)
(green)
(red)
Description
Warning Messages
Warning Messages
Information Messages
The indicators will light and/or flash as shown until the
cause is resolved.
If the green [SYNC] indicator is unlit, the unit’s clock is
unconfirmed.
The indicators will remain lit and/or flashing cyclically to
report the status.
If the orange [SYNC] indicator is unlit, the unit is operating
normally.
If the green [SYNC] indicator is unlit, the unit’s clock is
unconfirmed.
[SYNC] Indicators
Description
(orange) The word clock is
not set correctly.
Flash
(orange) Dante Network cir-
cuit is broken.
Flash x2
Other Dante-compatible devices
(orange) cannot be found
due to an incorrectly-wired Dante
Flash x3
Network.
Possible Solution
Set the clock master and sampling
frequency correctly on the
RSio64-D-native
device or in Dante
Controller.
(green)
Make sure that the
Ethernet cables
are connected correctly.
(green)
Description
(orange) A non-GbE-com-
patible device is
connected.
Light
or flash
(green)
Light
or flash
(green)
Light
or flash
Light
Description
Muted during
startup, or in the
(orange)
process of synchronization.
Lit
Make sure that the
Ethernet cables
are not removed or
short-circuited.
Flash
(green)
If the green indicator is flashing, the unit is the clock
master.
If the green indicator is lit, the unit is the clock slave and the
clock is synchronized.
[SYNC] Indicators
[SYNC] Indicators
Lit
Explanation
Please wait until
started has completed or until the
unit has finished
synchronization. It
may take up to 45
seconds for completion.
The unit is funcThe unit is operattioning correctly as
ing as the word
the word clock
clock master.
master.
The unit is functioning correctly as
the word clock
slave.
The unit is operating as the clock
slave and the clock
is synchronized.
Possible Solution
When transferring
audio via Dante,
use device that
supports GbE.
The [SECONDARY] connector
(orange)
has taken over
communications
during redundant
Flash
network operation.
Check the circuit
connected to the
[PRIMARY] connector.
An abnormality
has occurred on
the circuit con(orange)
nected to the
[SECONDARY]
connector during
Flash x2
redundant network operation.
Check the circuit
connected to the
[SECONDARY]
connector.
Owner’s Manual
23
Specifications
Specifications
General Specifications
Sampling Frequency
External Clock
Frequency Range
Signal Delay
44.1 kHz
+4.1667 %/+0.1 %/-0.1 %/-4.0 %
±200 ppm
48 kHz
+4.1667 %/+0.1 %/-0.1 %/-4.0 %
±200 ppm
88.2 kHz
+4.1667 %/+0.1 %/-0.1 %/-4.0 %
±200 ppm
96 kHz
+4.1667 %/+0.1 %/-0.1 %/-4.0 %
±200 ppm
SLOT IN (MY8-AE96) to SLOT OUT (MY8-AE96)
(@ fs=96 kHz, SRC off, Internal routing)
Less than 0.2 ms
SLOT IN (MY8-AE96) to Rio3224-D AES OUT
(@ fs=48 kHz, through Dante, SRC off)
(Dante Receive Latency set to 0.25 ms)
Less than 0.8 ms
SLOT IN (MY8-AE96) to Rio3224-D AES OUT
(@ fs=96 kHz, through Dante, SRC off)
(Dante Receive Latency set to 0.25 ms)
Less than 0.5 ms
SLOT IN (MY8-AE96) to Rio3224-D AES OUT
(@ fs=96 kHz, through Dante, SRC on, SLOT fs=48 kHz)
(Dante Receive Latency set to 0.25 ms)
Less than 1.1 ms
SRC
SRC Lock Range: 39.7 kHz – 101.7 kHz
Sample Rate Ratio Limit: 1:2.6 to 2.6:1
Dimensions (W x H x D) and Net Weight
480 x 88 x 365 mm, 6.1 kg
Power Requirements (wattage)
60 W
Power Requirements (voltage and hertz)
100-240 V 50/60 Hz
Temperature Range
Operating temperature range: 0 – 40 °C
Storage temperature range: -20 – 60 °C
Included Accessories
Owner’s Manual, AC power cord
Digital I/O Characteristics
Terminal
Format
Data Length
Level
Audio I/O
Connector
Primary/Secondary
Dante
24 bit or 32 bit
1000 BASE-T
64 ch Input/64 ch [email protected] kHz
32 ch Input/32 ch [email protected] kHz
etherCON CAT5e
Control I/O Characteristics
Terminal
Format
Level
Connector
WORD CLOCK IN
—
TTL/75 Ω terminated
BNC
External DC Input Characteristics
Terminal
Format
Level
Connector
EXT DC INPUT*1
—
—
XLR-4-32 type*2
*1: Power Requirements: +24V±2V, 3A
*2: 1pin=GND, 2pin=NC, 3pin=NC, 4pin=+24V
* The contents of this manual apply to the latest specifications as of the publishing date.
To obtain the latest manual, access the Yamaha website then download the manual file.
166
Owner’s Manual
Dimensions
Dimensions
365
360
430
1 2 3 4 5 6 7 8
ON
ON
88
480
1 2 3 4
Unit: mm
Owner’s Manual
167
Block Diagram
Block Diagram
AUDIO
CLOCK
SLOT1
16
16
1
1
SLOT CLOCK
SLOT1
WCLK IN
SRC OFF
2
Dante
PRIMARY
64
Dante
2
SRC WCLK
CH1/2 3
64
SRC
w/ thru
Dante
SECONDARY
SLOT2
Same above
WCLK IN
1 8 channels when SLOT CLOCK is 96kHz.
2 32 channels when SYSTEM CLOCK is 96kHz.
3 Channels 7/8 when using the MY8-AEB.
168
Owner’s Manual
SLOT1 1/2
WCLK IN
Same above
WORD CLOCK
SLOT4
Same above
SYSTEM CLOCK
SLOT3
Dante
128x128
Patch
Owner’s Manual
169
ADDRESS LIST
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: +1-416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: +1-714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9, Col. San José
Insurgentes, Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: +52-55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B – Vila
Olímpia – CEP 04551-010 – São Paulo/SP, Brazil
Tel: +55-11-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK,
Buenos Aires, Argentina
Tel: +54-11-4119-7000
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Edif. Torre Banco General, Piso 7, Urbanización
Marbella, Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
EUROPE
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: +44-1908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-303-0
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5b, 4133 AB Vianen, The Netherlands
Tel: +31-347-358040
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activités de Pariest,
77183 Croissy-Beaubourg, France
Tel: +33-1-6461-4000
ITALY
Yamaha Music Europe GmbH, Branch Italy
Via Tinelli N.67/69 20855 Gerno di Lesmo (MB),
Italy
Tel: +39-039-9065-1
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas de Madrid, Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
19th klm. Leof. Lavriou 190 02 Peania – Attiki,
Greece
Tel: +30-210-6686168
SWEDEN/FINLAND/ICELAND
Yamaha Music Europe GmbH Germany filial
Scandinavia
JA Wettergrensgata 1, 400 43 Göteborg, Sweden
Tel: +46-31-89-34-00
DENMARK
Yamaha Music Denmark,
Fillial of Yamaha Music Europe GmbH, Tyskland
Generatorvej 8C, ST. TH. , 2860 Søborg, Denmark
Tel: +45-44-92-49-00
NORWAY
Yamaha Music Europe GmbH Germany Norwegian Branch
Grini Næringspark 1, 1332 Østerås, Norway
Tel: +47-6716-7800
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, entrance 7, bld. 7, Kievskaya street,
Moscow, 121059, Russia
Tel: +7-495-626-5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
AFRICA
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH, Branch
Switzerland in Thalwil
Seestrasse 18a, 8800 Thalwil, Switzerland
Tel: +41-44-3878080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
POLAND/LITHUANIA/LATVIA/ESTONIA
Yamaha Music Europe GmbH
Sp.z o.o. Oddział w Polsce
ul. Wielicka 52, 02-657 Warszawa, Poland
Tel: +48-22-880-08-88
MALTA
Olimpus Music Ltd.
Valletta Road, Mosta MST9010, Malta
Tel: +356-2133-2093
ASIA
Yamaha Music Gulf FZE
JAFZA-16, Office 512, P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: +86-400-051-7700
INDIA
Yamaha Music India Private Limited
P-401, JMD Megapolis, Sector-48, Sohna Road,
Gurgaon-122018, Haryana, India
Tel: +91-124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: +62-21-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, Dongsung Bldg. 21, Teheran-ro 87-gil,
Gangnam-gu, Seoul, 06169, Korea
Tel: +82-2-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn. Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: +60-3-78030900
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: +65-6740-9200
TAIWAN
Yamaha Music & Electronics Taiwan Co.,Ltd.
2F., No.1, Yuandong Rd. Banqiao Dist.
New Taipei City 22063, Taiwan, R.O.C.
Tel: +886-2-7741-8888
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15, 16th Fl., Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: +66-2215-2622
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yamaha Corporation
Sales & Marketing Division
10-1, Nakazawa-cho, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
OCEANIA
AUSTRALIA
MIDDLE EAST
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz
Böl. No:3, Sariyer Istanbul, Turkey
Tel: +90-212-999-8010
CYPRUS
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany
Tel: +49-4101-303-0
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
VIC 3006, Australia
Tel: +61-3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation
Sales & Marketing Division
10-1, Nakazawa-cho, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
OTHER COUNTRIES
Yamaha Music Gulf FZE
JAFZA-16, Office 512, P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
HEAD OFFICE Yamaha Corporation, Commercial Audio Business Division
PA46
10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650
170
Owner’s Manual
MEMO
Yamaha Pro Audio global website
http://www.yamahaproaudio.com/
Yamaha Downloads
http://download.yamaha.com/
Manual Development Group
© 2015 Yamaha Corporation
Published 12/2016 POHD-B0
Printed in China
ZX32880
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement