2009 Catalogue_v1.pub - Electrathon of Tampa Bay

2009 Catalogue_v1.pub - Electrathon of Tampa Bay
OCEAN CONTROLS - Introduction
August 2009
ELECTRICAL PARTS—42
Dear Customers
ENCLOSURE—44
New things that we have added to our catalog this month include
Real Time Clock Module page 96
Latching Emergency Stop Switch page 90
3onedata Non-Isolated USB to RS485/422 Converter page 16
3onedata RS232 to RS485 Converters page 17
3onedata Ethernet - RS232/RS422/RS485 page 18-19
3onedata Lightning Protection Devices page 19
uLog - The Lil'est Logger page 25
Polymer Lithium Ion Batteries - 100mAh page 103
Serial Graphic LCD 128x64 page 81
Arduino Mega page 29
Arduino MegaShield Kit page 29
Not all our products are shown in the catalog. To see the full range
and to view more details about our products please visit our website at
www.oceancontrols.com.au
Please note all prices are in Australian dollars and are ex GST.
Australian customers should add 10% to the price when purchasing goods
www.oceancontrols.com.au
Ocean Controls
PO Box 2191
Seaford BC
Factory 3, 24 Wise Ave
Seaford
Vic, Australia 3198
Ph +61 3 9782 5882 Fax +61 3 9782 5517
email info@oceancontrols.com.au
MICROCONTROLLER PROGRAMMERS—45
MOTOR CONTROLLERS—46
MOTORS—57
SOFTWARE—63
RELAYS AND RELAY CARDS—65
FANS-70
PLC - PROGRAMMABLE CONTROLLERS-71
DATA ACQUISITION—2
PANEL METERS—78
COMPUTER PARTS—11
SIGNAL CONDITIONERS—82
COMPONENTS—13
SENSORS—84
COMMUNICATIONS—16
POWER SUPPLIES AND BATTERY CHARGERS—97
DATALOGGERS—24
DC-DC CONVERTERS— 100
CONTROLLERS RELAY & REMOTE —26
TEST EQUIPMENT—104
CONTROLLERS TEMPERATURE & PROCESS —33
TOOLS—110
COUNTERS AND TIMERS—39
AUDIO—112
Page 1 Ocean Controls Catalog 2009
OCEAN CONTROLS - DATA ACQUISITION
LabJack U12
LabJack UE9 and UE9-Pro
USB-based multifunction data acquisition and control device
USB/Ethernet data acquisition module
Features:
8 Single-Ended, 4 Differential 12-Bit Analog Inputs
±10 Volt Analog Input Range
PGA with Gains of 1, 2, 4, 5, 8, 10, 16, or
20 V/V
Up to 8 kSamples/Sec (Burst) or 1.2
kSamples/Second (Stream)
Supports Software or Hardware Timed
Acquisition
Supports Triggered Acquisition
2 Analog Outputs
20 Digital I/O (Up to 50 Hz per I/O)
32-Bit Counter.
Software is included including activex component
Price Each
LAJ-001
1
$215.00
A high speed and accurate data acquisition module. The UE9-Pro has all the
features of the normal UE9 with the
addition of an auxiliary low-speed hiresolution (24-bit) sigma-delta ADC.
Features:
14 Analog Inputs (12-16 bits depending
on speed
±5 or 0-5 Volt Maximum Analog Input
Range
Analog Input Streaming upto 50KHz (Ethernet)
2 Analog Outputs
2 Counters (32 Bits)
23 Digital I/O
Supports Software or Hardware Timed Acquisition
Copy of DaqFactory Express, Labview Drivers and ActiveX component
5+
POA
Price Each
LAJ-011 Labjack UE9
LAJ-015 Labjack UE9-Pro
LabJack U3 USB Data Acquisition Module LV
Features:
- 16 Flexible I/O (Digital Input, Digital
Output, or Analog Input)
- Up to 2 Timers (Pulse Counting/Timing,
PWM Output, Quadrature Input)
- Up to 2 Counters (32-Bits Each)
- 4 Additional Digital I/O
- Up to 16 12-bit Analog Inputs (0-2.4 V or
0-3.6 V, SE or Diff.)
- 2 Analog Outputs (10-Bit, 0-5 volts)
- Supports SPI, I2C, and Asynchronous Serial Protocols (Master Only)
- Built-In Screw Terminals for Some Signals
- USB 2.0/1.1 Full Speed Interface
- Powered by USB Cable
- Drivers Available for Windows, Linux, Mac and Pocket PC
- Examples Available for C/C++, VB, LabVIEW, Java, and More
- Includes Licensed Copy of DAQFactory Express Software (Win2000/XP)
- Includes USB Cable and Screwdriver
- Free Firmware Upgrades
- Money Back Guarantee
- Enclosure Size Approximately 3" x 4.5" x 1.2" (75mm x 115mm x 30mm)
- Rated for Industrial Temperature Range (-40 to +85 Degrees C)
LabJack U3 USB Data Acquisition Module HV
Differences with the HV (High-Voltage) Version:
- First 4 Flexible I/O are Changed to Dedicated HV Analog Inputs.
- 4 HV Inputs have ±10 Volt or -10/+20 Volt Range.
- 12 LV Inputs (Flexible I/O) Still Available, for 16 Total Analog Inputs.Price Each
1
LAJ-021 Labjack U3 USB Data Acquisition Module LV $179.00
LAJ-022 Labjack U3 USB Data Acquisition Module HV $189.00
LAJ-023 LABJACK U3 Data Acquisition OEM Module $129.00
5+
POA
POA
POA
1
$689.00
$839.00
LABJACK U6 USB
DATA ACQUISITION MODULE
Features
The U6-Pro has all the features of the normal U6 with the addition of an
auxiliary low-speed hi-resolution (24-bit) sigma-delta ADC. This converter takes about 125 ms per sample and provides an effective resolution of about 22-bits over the 0-5 or +/-5 volt ranges. Linearity and accuracy are also improved compared to the normal converter.
14 Analog Inputs (16-18+ Bits Depending on Speed)
U6-Pro Adds 24-bit Low-Speed ADC for 22-Bit Effective Resolution
Single-Ended Inputs (14) or Differential Inputs (7)
Instrumentation Amplifier Inputs
Software Programmable Gains of x1, x10, and x100
Analog Input Ranges of ±10, ±1, and ±0.1
Volts
Built-In CJC Temperature Sensor
2 Fixed Current Outputs (200/10 uA)
2 Analog Outputs (12-Bit, ~0-5 Volts)
20 Digital I/O
Up to 2 Counters (32 Bits Each)
Up to 4 Timers (Pulse Timing, PWM Output, Quadrature Input, ...)
Supports SPI, I2C, and Asynchronous Serial Protocols (Master Only)
Supports Software or Hardware Timed Acquisition
Maximum Input Stream Rate of 50 kHz (Depending on Resolution)
Capable of Command/Response Times Less Than 1 Millisecond
Built-In Screw Terminals for Some Signals
USB 2.0/1.1 Full Speed Interface
Powered by USB Cable
Drivers Available for Windows, Linux, Mac and Pocket PC
Examples Available for C/C++, VB, LabVIEW, Python, and More
Includes Licensed Copy of DAQFactory Express Software (Win2000+)
Includes USB Cable and Screwdriver
Free Firmware Upgrades
Money Back Guarantee
Enclosure Size Approximately 3" x 7" x 1" (75mm x 185mm x 30mm)
Rated for Industrial Temperature Range (-40 to +85 Degrees C)
Price Each
1
LAJ-041 LABJACK U6 Data Acquisition Module
$475.00
LAJ-042 LABJACK U6-Pro Data Acquisition Module $575.00
Page 2 Ocean Controls Catalog 2009
5+
POA
POA
5+
POA
POA
OCEAN CONTROLS - DATA ACQUISITION
CB-15 Labjack U3 Terminal Board
Labjack LJTick—InAmp
Provides convenient screw terminals for
the DB15 connector on the LabJack U3
and UE9. The CB15 can connect directly
to the U3 and UE9
on the LabJack UE9.
Price Each
LAJ-014 CB-15 Terminal Board
1
5+
$70.00 POA
CB-25
Labjack Terminal Board
Price Each
LAJ-031 LJTick-InAmp
Most of the connections on the LabJack
U12 have built-in screw terminals, but 16
of the digital I/O are accessed with a DB25 connector. To ease the use of these
digital ports the CB25 provides screw
terminal connections. It also provides
short-circuit/overvoltage protection for
the 16 I/O which are accessed through
the DB25 connector.
Price Each
LAJ-002
Signal-conditioning module provides
two instrumentation amplifiers ideal for
low-level signals such as bridge circuits
(e.g. strain gauges) and thermocouples. The LJTIA has switches to
choose from 5 gain settings (x1, x11,
x51, x201, or custom) and two output
voltage offsets. The 4-pin design plugs into the standard AIN/AIN/GND/
VS screw terminal block found on newer LabJacks such as the U3 and
UE9. (RoHS=YES).
1
$89.00
5+
POA
Labjack LJTick—RelayDriver
The LJTick-RelayDriver (LJTRD) allows 2
digital I/O lines on a Labjack U3 or UE9 to
control a relay or other moderate load up to
50V/200mA.
1
5+
$85.00 POA
Price Each
LAJ-032 LJTick-InAmp
1
$27.50
5+
POA
CB-37 Labjack UE9 Terminal Board
EB-37 Experiment Board
Labjack LJTick—Proto
The CB37 Provides convenient screw terminals for the DB37 connector on the LabJack
UE9. The CB37 can connect directly to the
UE9.
The LJTick-Proto (LJTP) consists of an 8x8 grid of
holes for prototyping custom signal-conditioning
ticks for the LabJack U3 or UE9.
Price Each
LAJ-033 LJTick-Proto
The EB37 experiment board connects to the LabJack UE9’s DB37
connector and provides convenient
screw terminal access. Also provided is a solderless breadboard
and useful power supplies (+/-10
volts, 3.3 volts, and 1.25 volts).
Includes a screwdriver, power supply, and jumper wires. For the LabJack UE9 only.
Price Each
LAJ-012 CB-37 Terminal Board
LAJ-013 EB-37 Development Board
1
5+
$84.00 POA
$165.00 POA
The LJTick-CurrentShunt (LJTCS) is a
signal-conditioning module designed to
convert a 4-20 mA current loop input signal
into a 0.47-2.36 volt signal compatible with
the LabJack U3 or UE9. The 4-pin design
plugs into the standard AIN/AIN/GND/VS
screw terminal block found on newer LabJacks such as the U3 and UE9.
Price Each
LAJ-034 LJTick-Current Shunt
The LJTick-Divider (LJTD) is a signal-conditioning module designed to
divide 2 single-ended channels of 010 volt analog signals down to 0-2.5
volt signals. It is suitable for use with
the Labjack U3 and UE9. The 4-pin
design plugs into the standard AIN/
AIN/GND/VS screw terminal block found on newer LabJacks such as
the U3 and UE9. The use of large resistors and a precision op-amp
buffer provide an input impedance of 1 MW. By adding or replacing
resistors, many other configurations are possible, such as a level shifter
that converts ±10 volts to 0-2.5 volts.
Page 3 Ocean Controls Catalog 2009
5+
POA
Labjack LJTick—Current Shunt
Labjack LJTick—Divider
Price Each
LAJ-030 LJTick-Divider
1
$25.00
1
$49.00
5+
POA
1
$69.00
5+
POA
LJTick-DAC
Provides a pair of 14-bit analog outputs
with a range of +/- 10 volts. Plugs into any
digital I/O block, and thus up to 10 of these
can be used per U3/UE9 to add 20 analog
outputs.Provides a pair of 14-bit analog
outputs with a range of +/- 10 volts. Plugs
into any digital I/O block, and thus up to 10 of these can be used per U3/
UE9 to add 20 analog outputs.
Price Each
LAJ-035 LJDAC- Digital to Analog Converter
1
$135.00
5+
POA
OCEAN CONTROLS - DATA ACQUISITION
Thermocouple amplifier
Dual Instrument Amplifier
A dual instrumentation amplifier from Electronic
Innovations Corp provides 2 high-impedance differential inputs. Operates from a single 5 volt supply
and provides a +/- 15 volt supply and a 4.096 volt
reference. Analog input range is +/- 10 volts. The
gain of each channel is set to 1, 10, 100, or 1000
via digital I/O or jumper wires. Typical current requirement is about 80 mA @ 5 volts, allowing the EI-1040 to be powered from a +5V terminal on the LabJack U12.
Can be used with the Labjack U12, U3 or UE9
Price Each
LAJ-004 Dual Instrumentation Amp
1
$185.00
5+
POA
Dual DC Amplifier
Our dual amplifier or voltage divider module
allows you to amplify signals by a factor of 1.5
to x10 or reduce signals by a factor 0.667 to
0.1 You can easily convert 4 to 20mA signals
to a voltage.
The dual DC amplifier circuit consists of two
non inverting amplifiers (OP1 and OP2) with a
voltage divider at the input.
Each amplifier is identical in design and is
issued with one 50K potentiometer. Whether
the circuit amplifies or reduces the amplitude
of the signal depends on where the 50K potentiometer is placed on the circuit. A simple jumper allows the circuit to
operate off a 9 to 24V supply for amplification of unipolar signals or it
can be powered by a +/-9 to 15V supply for amplification of bipolar signals.
You can purchase the dual amplifier module as a kit or fully assembled
and tested. If you are purchasing it assembled and tested it comes in 3
forms
- Dual Amplifier
- Dual Voltage Divider
- Amplifier and Voltage Divider
If you require 4-20mA conversion to voltage contact us with your required voltage output.
The card also has optional DIN rail mounts
Price Each
KIT-200 Dual Amplifier as a kit
KTA-201 Dual Amplifier Assembled
KTA-202 Dual Volt Divider Assembled
KTA-203 Dual Amp & Volt Divider Assembled
KIT-204 DIN Rail Mount
Page 4 Ocean Controls Catalog 2009
1
$25.00
$39.00
$39.00
$39.00
$13.50
5+
less 10%
less 10%
less 10%
less 10%
less 10%
Often you want to connect a J or K Type
Thermocouple signal to a data acquisition system.
A lot of data acquisition modules have
analog inputs which only accept 0-5V or
0-10V signals. Our TC Amplifier card
allows you to connect a J or K thermocouple to it and convert the signal to a
10mV/DegC output
Our TCAMP board comes in a number of different models
KTA254 - J Thermocouple amplifier with 10mV/degC output
KTB254 - J Thermocouple amplifier with 4-20mA output over 0-200 or 0
-1000degC
KTC-254 - K Thermocouple amplifier with 10mV/degC output
KTD-254 - K Thermocouple amplifier with 4-20mA output over 0-200 or
0-1000degC
KTE-254 - 0-2V/0-10V to 0-20/4-20mA converter
KTF-254 – LM35 to 4-20mA
Circuit
Our Thermocouple amplifier card uses the AD594 (J Thermocouple) or
AD595 (K Thermocouple) integrated circuits. Each of these feature inbuilt cold junction compensation. The AD594/5 will output 10mV/degC
which is available on one of the screw terminals.
The card can also be fitted with a AD694 which will convert the output of
the AD594/5 to a 0-20mA or 4-20mA signal. Links on the board allow the
4-20mA to be over a 0-200degC or 0-1000degC range
If you wish to use the card as a voltage to current converter we can sell
it without the AD594/5 integrated circuit providing a cheap 0-2V/0-10V to
0-20mA/4-20mA converter.
Price Each
KTA-254 J Thermocouple Amplifier 10mV/Deg Out
KTB-254 J Thermocouple Amplifier 4-20mA Out
KTC-254 K Thermocouple Amplifier 10mV/Deg Out
KTD-254 K Thermocouple Amplifier 4-20mA Out
KTE-254 0-10V to 4-20mA Converter
KTF-254 LM35 to 4-20mA
1
$45.00
$65.00
$45.00
$65.00
$45.00
$45.00
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - DATA ACQUISITION
iUSBDaq Module
Temperature Probe –40 to 100 degC
An inexpensive and easy to use temperature probe. Designed to work with a LabJack, but can also be used with any voltage measuring device. Outputs 10 mV
per degree C, and has a range of -40 to
+100 degrees C.
Price Each
LAJ-003
1
$65.00
5+
POA
Stainless Steel Temperature Probe
An easy to use, very accurate, and waterproof temperature probe from Electronic Innovations Corp.
The sensor is mounted in a stainless steel sheath
and features a high-level linear output of 10 mV per
degree F, typical accuracy of +/-0.25 degrees C ( +/0.4 degrees F) at room temperature, and a range of
0 to +300 degrees F (-17 to +150 degrees C, with
U3/UE9). Can be used with all labjacks but can also be used with any
other voltage measuring device
Price Each
LAJ-006
1
$99.00
5+
POA
Digital Temperature/Humidity Probe
EI-1050 Digital Temperature/Humidity Probe.
The EI-1050 uses two digital lines on the LabJack U12 (IO0 and IO1) to retrieve temperature
and relative humidity measurements. Can also
be used with Labjack U3 and UE9 Featuring
the Sensirion SHT11 sensor it provides 14-bit
temperature readings and 12-bit humidity readings. An enable line is
provided allowing up to 20 EI-1050 probes to be connected to a single
LabJack U12. Measurement range is -40 to 120 degrees C for temperature and 0 to 100% for humidity. Accuracy is +/-0.5 degrees C (@ 25
deg C) and +/-3.5%.
Price Each
LAJ-005
1
$125.00
5+
POA
The iUSBDAQ - U120816 is the lowest cost USB data acquisition module.
It is USB 2/1.1 compliant.
It features eight 12-bit analog inputs,
16 digital I/O lines, two programmable
pulse-width output channels, and one
16-bit counter channel. Analog sampling rate is up to 32 ksamples/s for
all 8 channels, with single channel up
to 13 ksamples/s. All I/O is connected
via screw connectors.
Dimensions 90 x 85 x 30mm
The package comes with all free usb cable, screw driver, device driver,
DLL, LabVIEW driver, dot net wrapper class, rich examples
and free ready-to-run iDAQTest&Log testing and data logging software.
Price Each
HYT-001 iUSBDaq Data Acquisition Module
1
$155.00
4+
less 10%
iUSBDAQ Data Acquisition and Logger Module
The iUSBDAQ - U1208LOG is the only multifunction three in one (3-in-1) USB
data acquisition module that provides PC
control mode for fast speed data acquisition
and transfer (up to 64KSamples/s) as well
as standalone data logging mode for
direct data logging into USB flash drive
without computer, the storage capacity is
virtually unlimited, it's up to your USB flash
disk space. Another unique feature that iUSBDAQ - U1208LOG brings,
is the build-in video functions in programming APIs as well as in the
FREE ready-to-run iDAQTest&Log software for easy integration and
synchronization of data and video. A dedicated video trigger output line
is also provided in the hardware for external synchronization with other
devices. Works with USB Flash Drives up to 2GB.
Price Each
1
5+
HYT-010 iUSBDaq Data acquisition and Logger module $325.00 less 10%
USB-010 5VDC USB Power Supply 100-240VAC
$18.14 less 10%
USB-011 5VDC USB Power Supply 12VDC Car Powered $8.32 less 10%
NET-Link Ethernet Board
Netiom-Link works as a pair of devices
communicating over an ethernet network. Each Netiom-Link transmits a
packet of data to its opposite end containing information about its input
status. Upon receipt of this data the
receiving device changes its outputs to
be the same as the inputs on the transmitting unit.
In this way all 16 inputs on one Netiom
–Link are reflected on the outputs of the second Netiom-Link. Hence a
switch on one can operate a relay on the other. In a similar way serial
data coming into one port will be transmitted out of the serial port of the
second Netiom-Link.
Price Each
NET-005 NET-Link Ethernet Board
Page 5 Ocean Controls Catalog 2009
1
$49.00
OCEAN CONTROLS - DATA ACQUISITION
myPCLab Data Acquisition Module
4 Probe Temperature Logger
is a very compact Data Acquisition tool
which connects to a PC via a USB port. It
has two universal analog inputs
(Thermocouples type J, K, T, E, N, R, S and
B, Pt100 RTD (3-wire), 4-20 mA, 0-50 mVdc
or 0-10 Vdc) and one digital input. From
hobbyists to scientists, from simple technical
tasks to complex engineering activities,
myPCLab can be an invaluable tool for online monitoring and data logging in school,
laboratory research, machine data recording and industrial understanding. It comes with an intuitive and easy-to-use Windows software which
plots and records data, shows gauges, bargraphs and digital readouts.
The USB port is accessed as a virtual serial port which makes myPCLab
compatible with SCADA softwares with Modbus RTU driver or with any
program with ASCII serial communication. Multiple units of myPCLab
can be connected to the same computer.
Price Each
NOV-010 myPCLab Data acquisition module
1
$129.00
5+
less 10%
myPCProbe temperature or temperature and humidity sensor
Features:
- myPCProbe-RHT: For temperature and humidity measurements from 20 to +100°C and 0 to 100 %RH (also available as dew point)
- Sampling rate: one sample every 1 or 3 seconds, depending on the
programmed resolution
- Response time: 4 s (RH) or 30 s (T) in fairly still air
- myPCProbe-TEMP: For temperature measurements in different
ranges, according to the specified sensor. Available for thermocouple
types J, K, T, E, N, R, S and B and Pt100 RTD
- Internal temperature sensor for cold junction compensation or handle
temperature monitoring
- Accuracy: 0.2% of full scale for Pt100; 0.25% of FS ±3°C for thermocouples type R, S and B; 0.25% ±1°C for all other thermocouples;
±1,5ºC for internal temperature sensor
- Sampling rate: 8 to 128 samples per second, depending on the A/D
resolution
- A/D resolution: programmable from 15 to 11 bits, depending on the
sampling rate
- Automatic cold juction compensation for thermocouples
- Cable resistance compensation for Pt100
- Computer interface: USB V1.1 Plug and Play, Virtual Serial Port driver
- USB connection: 1.5 m cable with Type-A USB plug
- Double communication protocol: ASCII & Modbus RTU
- Powered by the USB bus
- Consumption: <100 mA
- Free Windows software provides configuration, visualization, recording
and data export. Provides simultaneous communication with multiple
myPCProbe and myPCLab devices
- Data export formats: txt, xls, rtf, pdf, html, xml, dbf, csv
- Compatible with Windows 2000, XP (up to SP2) and Vista
Page 6 Ocean Controls Catalog 2009
The DS18S20 has an operating temperature range of -55°C to +125°C and
is accurate to ±0.5°C over the range of
-10°C to +85°C. The sensors can be mounted up to
200metres away from the logger.
Windows Datalogging Software included
Price Each
KIT-145 Kit
KTA-145 Assembled and Tested
PTP-003 DS18S20 Temperature Sensor
1
$36.00
$49.95
$12.00
5+
less 10%
less 10%
less 10%
K145 Server
The Ocean Controls K145 Server Software
is a budget priced Windows based HTTP,
Email and Modbus TCP Server for the K145
4 Channel Temperature Logger.
myPCProbe is a temperature or temperature
and humidity sensor which connects to a PC
via a USB port. From hobbyists to scientists,
from simple technical tasks to complex engineering activities, myPCProbe can be an invaluable tool for on-line monitoring and data
logging in school, laboratory research, machine data recording and industrial understanding.
Price Each
NOV-020 myPCProbe Humidity and Temperature Probe
NOV-021 myPCProbe 6x300mm temperature probe
NOV-022 myPCProbe 6/3x150mm sharp temp. probe
This kit is a 4 channel temperature
meter and logger. The temperature
data, in degrees C or F, is output as a
continuous data stream over an RS232
serial port. The kit uses 4 x DS18S20
digital thermometers (only 1 is supplied
- more are available on request). A
data logger windows program is supplied on CD featuring trends, min-max
1
5+
$159.00 less 10%
$149.00 less 10%
$149.00 less10%
Main Features:
-Monitor Temperatures in Real Time from
anywhere in the world over the Internet,
using only a web browser
-Easily see if Temperatures are within
Alarm Limits
-Monitor Maximum and Minimum Temperatures
-Sends Emails to three different email addresses when Temperature
enters Alarm State and returns to Normal
-View real time and Logged Data using Modbus TCP connection
Price Each
OCS-145 K145 Server Pack
OCS-146 K145 Server Software
PTP-003 DS18S20 Temperature Transducer
1
$99.00
$59.00
$12.00
OCEAN CONTROLS - DATA ACQUISITION
Digirail 2 Channel Universal Analog Input Module
DAS005 - 12 Bit Data Acquisition Module
The DAS005 is a 12 bit data acquisition module which features
- a 12 bit ADC with 8 single ended inputs
reading 0 to 4 Volts. The inputs can withstand up to +/-20V.
- ADC conversion time of less than 10 usecs.
Note using windows software reduces this
speed
- 4 Digital Inputs that are TTL and CMOS
compatible
- 4 Digital Outputs that are TTL and CMOS compatible that are capable
of sourcing and sinking 6mA.
Requires 9-12VDC power
Price Each
KIT-005 DAS005 As Kit
KTA-005 DAS005 Assembled and Tested
1
$89.00
$125.00
5+
less 10%
less 10%
Price Each
SIG-100
D25 Terminal Board
The D25 male connecter to terminal card
allows you to easily connect to screw terminals
Can be used to add terminal connections to
the DAS005 and Labjack U12
1
5+
$45.00 less 10%
$65.00 less 10%
D15 Terminal Board
The D15 female connecter to terminal card allows you
to easily connect to screw terminals
Available in DIN Rail Mounting
Price Each
DTC-009 D9 Terminal Card
DTD-009 D9 Card DIN Rail Mounted
1
$149.00
5+
less 10%
Digirail 4 Channel Digital Input/Counter Module
Available in DIN Rail Mounting
Price Each
DTC-001 D25 Terminal Card
DTD-001 Card DIN Rail Mounted
This module can be used to monitor 2 analog
inputs.
Features of the module include 2 Analogue inputs: programmable for thermocouples (J, K, T, E, N, R, S, B), Pt100, mV, V, mA.
Cold junction compensation for thermocouples
and compensation for Pt100 3-wire cables.
Open loop detection for thermocouples, Pt100
and mV.
Sampling rate for 1 analogue input: 10Hz for mV,
V and mA. 5Hz for t thermocouples and Pt100.
Analogue input resolution: 17 bits.
User defined linearization for the analogue inputs.
Power: 10 to 35Vdc, 50mA maximum current.
2-wire RS485 communication with Modbus RTU protocol. Configurable
address and baud rate (1,200 to 115,200bps).
LED indicators for communication and status.
1
5+
$39.00 less 10%
$45.00 less 10%
This module can be used to monitor the status of digital inputs or count
pulses.
Features of the module include Digital inputs: in voltage, 4 to 35V to activate.
Internally limited current to 5mA.
Maximum count frequency: 1000 Hz for signals
with square wave and working cycle of 50%.
Input 1 can be configured for counting signals of
up to 100 kHz.
Counting capacity (per input): 32 bits (0 to
4294967295)
Power: 10 to 35Vdc, 50mA maximum current.
2-wire RS485 communication with Modbus RTU
protocol. Configurable address and baud rate
(1,200 to 115,200bps).
LED indicators for communication and status.
Price Each
SIG-101
1
$149.00
5+
less 10%
Digirail 2 Relay Output Module
Webserver WS10 Module
The WebServer WS10 is a device for data acquisition, logging and
transmission. It is capable of integrating instruments and sensors to the
Internet, ethernet and wireless. The inputs for data acquisition can be
either the 4 built-in analog and digital inputs or any inputs from the external equipments connected to the WS10 through the RS485 interface
(Modbus protocol). Data transfer can be accomplished through the
ethernet interface or modem (mobile or conventional) using ordinary
Internet resources, such as the internet
browser, e-mail and TCP connection.
Internal memory for off-line data logging
(16 bit CPU, with 512KB RAM)
2 Serial Interfaces (RS232, RS485 or
Modem)
Ethernet 10BaseT Interface. It suports
TCP/IP, PPP (client and server), HTTP,
FTP, SMTP, DHCP, Modbus TCP, Modbus RTU protocols
Mobile wireless networks (GSM GPRS or
CDMA 1XRTT) email in case of alarm
Price Each
NWS-001 Webserver WS10 Module
Page 7 Ocean Controls Catalog 2009
1
$1499.00
This module can be used to control 2 relay
outputs.
Features of the module include 2 Relay outputs: 3A / 250Vac SPDT relay, resistive load.
Power: 10 to 35Vdc, 50mA maximum current.
2-wire RS485 communication with Modbus
RTU protocol. Configurable address and baud
rate (1,200 to 115,200bps).
LED indicators for communication and status.
Windows based configuration software.
Dimensions: 72 x 78 x 19mm.
Mounting: 35mm DIN rail.
Working temperature: 0 to 70°C.
Price Each
SIG-102 Digirail 2 Relay Output Module
1
$149.00
5+
less 10%
OCEAN CONTROLS - DATA ACQUISITION
MA-8AD MA 8 channels analog input
MA-8X8YR MA 8 channels digital input 8 channels
Descriptions:
*8 points input
*8 points relay output
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other
devices
*Can extend 16 this kind of modules at most
Price Each
1
5+
PLC-500 MA-8X8YR MA8channels digital input 8channels digital output$144.00 less10%
Descriptions:
*8
channels analog input
*12 bits high precision input
*current/voltage mode selectable
*voltage mode output range: DC 0~5V, 0~10V
*current mode output range:DC 0~20mA, 4~20mA
*PID control function
*self-study PID parameters
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other devices
*Can extend 16 this kind of modules at most
Specifications:
MA-6PT-P 6 channels PT100 temperature input, PID
control inside
Voltage: DC0~5V、0~10V( exterior load resistor
Maximum input range: Voltage: ±18V; Current: 0~40mA
Digital output range: 12 bits binary numbers
Descriptions:
*6 channels Platinum temperature sensor input, resolution degree is PT100
*6 channels have individual PID function and can self
study PID parameters
*1mA constant current output, will not be interfered by
outsdie environment
*Resolution is 0.1℃
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other devices
*Can extend 16 this kind of modules at most
Resolution: 1/4095(12Bit)
Integrated precision:0.8%
Conversion speed: 20ms per channel
Power supply for analog: DC24V±10%,100mA
Installation: Use M3 screw or fix on DIN46277 rail ( width 35mm )
Price Each
PLC-503 MA-8AD MA 8 channels analog input
Specifications:
Analog input signal: Pt100 Pt hot resistance
Measure temperature range: -100℃~350℃
Digital output range: Full-scale 4095, 12 bits with sign, binary
Control precision: ±0.1℃
Resolution: 0.1℃
Integrated precision: 0.8% ( related maximum )
Conversion speed: 20ms/1 channel
Power supply for analog: DC24V±10%,50mA
Installation: Use M3 screw or fix on DIN46277 rail ( width 35mm )
Profile dimension: 63mm×102mm×73.3mm
Price Each
Analog input range:
2KΩ~1MΩ); Current: DC0~20mA、4~20mA( exterior load resistor less than
500Ω)
1
$329.00
5+
less 10%
MA-4AD2DA 4 channels analog input and 2 channels analog output
1
5+
PLC-501 MA-6PT-P6channelsPT100temperature input, PID control inside $349.00 less 10%
Descriptions:
*4
channels analog input
*2 channels analog output
*12 bits high precision input
*current/voltage mode selectable
*voltage mode output/input range: DC 0~5V, 0~10V
*current mode output/input range:DC 0~20mA, 4~20mA
*PID control function for analog input
*self-study PID parameters
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other devices
*Can extend 16 this kind of modules at most4 channels analog output
Specifications:
MA-4DA MA 4 channels analog output
Descriptions:
*4 channels analog output
*current/voltage mode selectable
*voltage mode output range: DC 0~5V, 0~10V
*current mode output range:DC 0~20mA, 4~20mA
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other
devices
*Can extend 16 this kind of modules at most
Analog input
range
Max input
range
Analog
output range
Specifications:
Voltage output: DC0~5V、0~10V( exterior load resistor 2KΩ~1MΩ)
Current output: DC0~20mA、4~20mA (exterior load resistor less than 500Ω)
Digital input range: 10 bits binary numbers
Resolution ratio: 1/1023(10Bit)
Integrated precision: 0.8%
Conversion speed: 3ms/1 channel
Power of analog quantity:DC24V±10%,100mA
Installation: Use M3 screw or fix on DIN46277 rail ( width 35mm )
Profile dimension: 63mm×102mm×73.3mm
Price Each
PLC-502 MA-4DA MA 4 channels analog output
Item
1
$329.00
5+
less 10%
Digital input
range
Digital
output range
Resolution
PID output
value
Integrated
precision
Conversion
speed
Power
supply for
analog
quantity
Analog input ( 4AD )
Analog output ( 2DA )
Voltage
input
0~5V,0~1
0V
0~20mA,4~20
mA
-
DC±18V
0~40mA
-
Current input
-
Voltage output
Current output
0~5V、0~10V,
( exterior load resistor
2KΩ~1MΩ)
0~20mA、
4~20mA
(exterior load
resistor less
than 500Ω)
-
10 bits binary number (0~1023)
12 bits binary number
(0~4095)
1/4095(12Bit)
1/1023(10Bit)
-
0~K4095
0.8%
20ms/1 channel
3ms/1 channel
DC24V±10%,100mA
Installation
Use M3 screw or fix on the DIN46277 ( width 35mm ) rail
Profile
dimension
63mm×102mm×73.3mm
Price Each
1
5+
PLC-504 MA-4AD2DA 4 channels analog input and 2 channels analog output $349.00 less 10%
Page 8 Ocean Controls Catalog 2009
OCEAN CONTROLS - DATA ACQUISITION
MA-6TC-P 6 channels type K thermocouple temperature input, PID control inside
Descriptions:
*6 channels temperature signal input
*6 channels PID control output
*Support K type thermocouple temperature sensor
*Precision is 1 ºC
*PID control function
*self-study PID parameters
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other devices
*Can extend 16 this kind of modules at most
MA-16Y MA 16 channels digital output
Descriptions:
*Include two types: MA-16YR and MA-16YT
*I/O extension for PLC
*16 points relay or transistor output
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other
devices
*Can extend 16 this kind of modules at most
Price Each
PLC-507 MA-16Y MA 16 channels digital output
Specifications:
1
$144.00
5+
less 10%
MA-16X MA 16 channels digital input
Using environment: 0℃~60℃
Descriptions:
Descriptions:
*16 points digital input
*I/O extension for PLC
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other
devices
*Can extend 16 this kind of modules at most
Measure temperature range: 0℃ ~1000℃
Digital output range: 0~4095, 12 bits with sign, binary
Precision: 1℃
Integrated precision: 1℃
Conversion speed: 20ms/1 channel
Power supply for analog: DC24V±10%, 50mA
Installation: Use M3 screw or fix on DIN46277 ( width 35mm ) rail
Profile dimension: 63mm×102mm×73.3mm
Price Each
1
5+
PLC-505 MA-6TC-P 6 channels type K thermocouple temperature input, PID
control inside
$349.00
less 10%
MA-4AD MA 4 channels analog input
Descriptions:
*4 channels analog input
*12 bits high precision input
*current/voltage mode selectable
*voltage mode output range: DC 0~5V, 0~10V
*current mode output range:DC 0~20mA, 4~20mA
*PID control function
*self-study PID parameters
*DC 24V power supply
*Support Modbus-RTU protocol
*RS485 port, can connect with PLC, HMI and other devices
*Can extend 16 this kind of modules at most
Specifications:
Analog input type: Voltage input; Current input
Analog input range: 0~5V,0~10V; 0~20mA,4~20mA
Maximum input range:DC±18V; 0~40mA
Digital output range: 12 bits binary value (0~4095)
Resolution: 1/4095(12Bit)
PID output range: 0~K4095
Integrated precision: 0.8%
Converting speed: 20ms per channel
Power for analog: DC24V±10%,100mA
Installation: Fix up the module with M3 screw or put on DIN46277 rail (width
35mm)
Profile dimension: 63mm×102mm×73.3mm
Price Each
PLC-506 MA-4AD MA 4 channels analog input
Page 9 Ocean Controls Catalog 2009
1
$292.00
5+
less 10%
Price Each
PLC-508 MA-16X MA 16 channels digital input
1
$135.00
5+
less 10%
OCEAN CONTROLS - DATA ACQUISITION
16 Digital Output Modbus Module
16 Digital Input Modbus Module
The TRP-C24, an isolated output open
collector RS-485 module, provides 16 digital outputs (100mA). All channels feature
screw terminals for convenient connection
of field signals as well as LED’s to indicate
channel working status. All outputs are
equipped with photo-couplers to protect the
module against high voltage spikes, as well
as ground potential differences. The module can be remote controlled by PC in ASCII or Modbus RTU protocol
over a RS485 network. Can be DIN Rail mounted with fitting
Specifications
- Output channel: 16 digital output channels (open collector).
- Digital output isolation: 3750Vrms.
- Communication interface: RS-485 differential 2 half/duplex wires.
- Communication speed form 1.2Kbps to 115.2Kbps auto-switching.
- Data format: Data bit: 8, Parity Check: None, Stop Bit: 1.
- Distance: up to 4000ft ( 1200M ).
TRP-C26 provides 16 optical isolated digital input channels that allow
you to input the logic signal from 0 to 30V DC. All inputs are equipped
with photo-couplers to protect the module against high voltage spikes,
as well as ground potential differences. The module can be remote controlled by PC in ASCII or Modbus RTU protocol over a RS485 network.
Can be DIN Rail mounted with fitting
Specifications
- Power Input Voltage: DC +10V to +30V.
- Input channel: 16 digital input channels
with counter.
- Input digital input counter: 0~65535.
- Input optical isolation: 3750 Vrms.
- Input logical level 0 +1V (max).
- Input logical level 1 +4.0V ~ +30V
- Leds to indicate status of digital inputs
Price Each
TRY-024 16 Digital Output Modbus Module
1
$130.00
5+
less 10%
4 Digital Input and 4 Relay Output Modbus Module
TRP-C28 provides with 4 optical isolate
digital input channels and 4 power relays
output. All channel features screw terminals
for convenient connection of field signals
as well as LED’s to indicate channel status.
Input channels are equipped with 3750Vms
DC isolation, and surge protection on RS485 data lines that protect the module and
device against high power voltage input
and ground potential differences. The module can be remote controlled
by PC in ASCII or Modbus RTU protocol over a RS485 network. Can be
DIN Rail mounted with fitting
Specifications
- Input logical level 0 +1V (max).
- Input logical level 1 +4.0V ~ +30V.
- Digital Input can be used as counter channel: 4
- Counter frequency: 100Hz.
- Output channel: 4 channel power reply outputs.
- Relay type: 2 Form A (RL1,RL2) , 2 Form C (RL3,RL4).
- Contact ratting: 5A /30V DC , 5A /120V AC , 5A /250V AC.
Price Each
1
TRY-028 4 Digital In and 4 relay output Modbus Module $199.00
Page 10 Ocean Controls Catalog 2009
5+
less 10%
Price Each
TRY-026 16 Digital Input Modbus Module
1
$127.50
5+
less 10%
8 Analog Input Modbus Module
TRP-C68 ,is an 8-channel Analog input
module. It accepts either a voltage or a
current signal and supports the sample
rate in “ Normal ” or “Fast” mode. All
channels feature screw terminals for
convenient connection, and LED’s to
indicate channel status. All inputs are
provided with isolation and surge protection to protect the module against high
voltage spikes, as well as ground potential differences. TRP-C68 support both ASCII and Modbus protocol over a RS485 network.
Specifications
- Resolution :16 bit
- Sample rate: Normal mode: 10 Fast Mode: 60 sample / sec.
- Zero drift: 0.03uV/C .
- Span drift:25 ppm/C .
- Accuracy: Normal 0.1 or better. Fast: 0.5 or better.
- Analog Input range:
Voltage:±10V,±5V,±2.5V,±1.25V,±650mV. Current: +/-20mA.
- CMRR:92 db min/50/60Hz
- Analog input over voltage protection:+/- 35V .
Price Each
TRY-068 8 Analog Input Modbus Module
1
$215.00
5+
less 10%
OCEAN CONTROLS - COMPUTER PARTS
4 PORT USB HUB
7 PORT USB HUB
The UH284 is ATEN's compact and highly
functional 4 port USB 2.0 hub series for the
desktop or the laptop. It features built-in Magnet Pads and can be placed almost anywhere.
UH284 provides 4 additional USB 2.0 ports for
existing USB Systems, including an easy access port which is ideal for connecting a flash
drive.
* Provides 4 additional USB 2.0 ports to existing USB Systems
* Four independent, fully functional, 480 Mbps, downstream ports
* Fully compliant with the USB 2.0 specification
* Per port overcurrent protection
Price Each
UHB-001 4 Port USB Hub
1
$22.50
5+
less 10%
Sunix Dual Parallel Port Card
Sunix's 4018T offers 2 ports of parallel for your
connection need. The port provides data transfer
rate up to 2.7 MB/sec. The card support 32-bit or
64-bit PCI bus with 3.3V or 5V and is readied for
64-bit system as well. It is plug-n-play capable
makes installation a breeze. The card also support
Re-Map to ISA address function.
Features include
- Support 32 bit / 64 bit PCI bus
- Universal PCI interface
- Data transfer speed up to 2.7MB/sec
- IEEE1284 standard compatible
- Re-map to ISA Address 278, 378
- Plug and Play
- Friendly Graphic User Interface
- Ready for 64 bit system
Price Each
COV-301 Sunix Dual Parallel Port Card
5+
less 10%
Sunix IEEE1284/Parallel PCMCIA Card 2 Port
5+
less 10%
1
$69.00
5+
less 10%
USB-Parallel Port Converter
1
$45.41
Box Of Connectors - BNC Pack
Our plastic pack contains all the BNC
connectors a technician needs for
connecting to and analyzing problems
2 - BNC T Adaptor 1 Male to 2 Female
2 - BNC Female to Female Adaptor
2 - BNC Terminator Plugs
2 - BNC Male to Double Binding
Posts/ Banana Sockets
All in a long lasting plastic box for the
technician to put in their tool box.
Our plastic pack contains all the gender
changers you need to sort out an RS232
connection.
A D9 Female to Female
A D9 Male to Male
A D25 Female to Female
A D25 Male to Male
A D25 Male to D9Female changer
A D25 Female to D9Male changer
A Null Modem Cable
All in a long lasting plastic box for the
technician to put in their tool box
Page 11 Ocean Controls Catalog 2009
Price Each
COV-305 Sunix Multi I/O PCI controller card
Price Each
COV-004 USB to Parallel Port Converter
Box Of Connectors - RS232 Gender Pack
1
$35.00
5+
less 10%
This converter allows you to connect standard (IEEE-1284) parallel printers. It includes
- True PnP & Bi-Directional printing
- An 'A' Type USB connector to 36 Pin
Centronics
- Length: 1.7m cable
- USB Port powered
- Drivers included
FEATURES
Compatible with 32 bit CardBus slot
Easy to Plug-n-Play installation
Simple and easy way to connect devices to your notebooks
Speed up to 2.7 MB/sec
Friendly Graphic User Interface
Price Each
BOX-001 RS232 Gender Pack
1
$54.50
Sunix Multi I/O PCI Controller Card
1
$43.95
1
$104.50
Price Each
UHB-002 7 Port USB Hub
Sunix's 4079T is a serial and parallel
combo expansion card. It offers you
two ports of DB9M connection plus one
port of parallel for all your project
needs. The serial ports have a data
transfer rate up to 921.6 Kbps and the
parallel ports offers speed up to 2.7
MB/sec. The card is ideal for project
like the POS system, automation assembly, ISDN terminal, and more. The serial card is plug-n-play capable and installation is a breeze. Bundle with the card is Sunix's unique
software which can increase the FIFO memory up to 128Kbyte.
* Support 32 bit / 64 bit PCI bus * Universal PCI interface
* 3.3V & 5V Universal PCI * Supports Windows, Linux, DOS
Sunix's parallel PCMCIA-2P offers you two
ports of Parallel port for all your connection
needs. The ports have a data transfer rate
up to 2.7 MB/sec. The card is plug-n-play
and installation is a breeze with the included driver CD.
Price Each
COV-310 Sunix Parallel PCMCIA Card 2 Port
High speed 7 port USB hub conforms to USB 2.0
specification and will operate at speeds up to
480Mbps. Power and 7 port LED indication. Simple, flexible and highly scalable connectivity solution between you PC and USB compliant device,
including cameras, scanners, printers and ultra fast
storage devices.
* Measures only 100mm Lx 58mm W x 15mm H
* Supports up to 127 Hi-Speed Devices
* 1.8mt USB lead andmains plugpack included.
* Supports Win 98SE, Me, 2k, XP and Vista
* Individual Port Over Current Protection
* Full compliance with USB Specs 2.0/1.1/1.0
5+
less 10%
Price Each
BOX-002 BNC Connector Pack
1
$34.50
5+
less 10%
OCEAN CONTROLS - COMPUTER LEADS
RS232 Serial Leads
USB Leads
DB9 Male to DB9 Female 1.8m
USB2.0 Type A Male to Type A Male
Price Each
CAB-002 DB9 male to DB9 Female 1.8m
1
$9.05
4+
less 10%
DB9 Male to DB9 Male 1.8m
Price Each
USB-001 USB2.0 Type A Male To Type A Male
1
$9.05
4+
less 10%
USB2.0 Type A Male to Type A Male
Price Each
CAB-008 DB9 Male to DB9 Male 1.8m
1
$7.59
4+
less 10%
DB9 Female to DB9 Female Null Modem 1.8m
Price Each
CAB-003 DB9 Female to DB9 Female Null 1.8m
1
$8.32
4+
less 10%
Price Each
USB-002 USB2.0 Type A Male To Type B Male
1
$9.05
USB2.0 Type A Male to 5 Pin Mini B
Use this to connect to a digital camera or camcorder
Length 1.8 metres
Price Each
USB-003 USB2.0 Type A Male To 5 Pin Mini Male
DB25 Male to DB25 Female 1.8m
Price Each
CAB-001 DB25 Male to DB25 Female 1.8m
1
$8.77
4+
less 10%
4+
less 10%
1
$9.05
4+
less 10%
USB Extension Lead
USB1.1 Extend the length of your USB device by
an additional 5-metres (16-feet) using this Active
USB Repeater Cable.
DB25 Male to DB25 Male 1.8m
Price Each
CAB-006 DB25 Male to DB25 Male 1.8m
1
$7.59
4+
less 10%
Price Each
COV-005 USB1.1 USB Data Extension Lead
1
$22.68
4+
less 10%
RJ45 Modular Patch Leads
DB25 Male to DB9 Female Modem Cable 1.8m
RJ45 Modular Patch Leads
Price Each
CAB-007 DB25 Male to DB9 Female Modem 1.8m
1
$8.45
4+
less 10%
Extra Long RS232 Serial Leads
Price Each
CAB-010 DB9 Male to DB9 Female Modem 5m
CAB-012 DB9 Male to DB9 Female Modem 10m
1
$11.45
$22.00
4+
less 10%
less 10%
1
$4.32
$4.32
$5.27
$5.27
$4.32
$4.32
4+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
RS232 Gender Changers
Price Each
CAB-101 D9 Female to D9 Female Gender Changer
CAB-102 D9 Male to D9 Male Gender Changer
CAB-103 D25 Female to D9 Female Gender Changer
CAB-104 D25 Male to D9 Male Gender Changer
CAB-110 D25 Female to D9 Male Gender Changer
CAB-111 D25 Male to D9 Female Gender Changer
Configurable RJ45 Adaptors
Price Each
CON-001 DB9 Female to RJ45 Female
CON-002 DB9 Male to RJ45 Female
1
$4.14
$4.14
4+
less 10%
less 10%
Price Each
1
4+
CON-003 DB25 Female to RJ45 Female $5.64 less 10%
CON-004 DB25 Male to RJ45 Female $6.50 less 10%
Page 12 Ocean Controls Catalog 2009
Price Each
CAB-030 Modular Patch Leads 0.5m
CAB-033 Modular Patch Leads 1m
CAB-036 Modular Patch Leads 2m
CAB-039 Modular Patch Leads 3m
CAB-042 Modular Patch Leads 5m
CAB-045 Modular Patch Leads 10m
CAB-048 Crossover Cat 5e cables 2m
CAB-051 Crossover Cat 5e cables 5m
1
$3.36
$4.21
$4.14
$5.45
$9.36
$13.55
$6.23
$7.96
4+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - COMPONENTS
Thumb Joystick
Breakout Board for Thumb Joystick
Description: This is a joystick very similar to
the 'analog' joysticks on PS2 (PlayStation 2)
controllers. Directional movements are simply two potentiometers - one for each axis.
Pots are ~10k each. This joystick also has a
select button that is actuated when the joystick is pressed down.
Price Each
SFJ-001 Thumb Joystick
Description: This is the breakout board for
the thumb joystick. Pins are broken out to a
0.1" header and includes 4 mounting holes in
the corners. The picture shows the joystick
mounted on the Breakout board
Dimensions: 1" x 1.25"
1
$6.00
5+
less 10%
Price Each
SFJ-002 Breakout Board for Thumb Joystick
Description: 4-way Pacman type arcade joystick. Heavy duty design
gives this joystick a great feel!
Features:
* ABS plastic and solid alloy construction
* Uses 4 microswitches to detect on/off
position
* Unique handle design
* Spring return to center
* Very rugged construction
Description: This is a heavy-duty joystick
very similar to the ones in claw arcade
games. Directional movements are momentary limit switches - one for each direction.
This joystick also has a select button that is
actuated when the red button is pressed
down.
This joystick is pretty beefy and very tall because of it. We built up an enclosure just to
see what it would look like. Ideally, this joystick would be panel mounted, but actually reading the movement of the
joystick is as simple as setting up the microcontroller to read five
switches.
Dimensions:
* Overall height: 101mm
* Base: 97x65mm
* Joystick height: 60mm
Dimensions:
1
$22.95
5+
less 10%
* Joystick height: 79mm
* Overall height: 190mm
* Base: 61.5mm square
Price Each
SFJ-004 Arcade Joystick - Long Handle
Big Dome Push Button
Description: It's the end of the world, and you
need a button to press. This is it. A 60mm
diameter dome illuminated push button
comes with a 12VDC@1.2 watt lamp, securing nut and a pre-installed long life horizontal
microswitch. Button can also be adjusted to a
low profile button by removing the middle
ring.
Description: This is a 33mm round momentary push button similar to the ones you find
on arcade games. Simple screw in design.
Perfect for mashing. Available in the colors
Blue, Green, Pink and Yellow
Note: Some basic assembly required.
Features:
* Bulb and Bulb holder included
* Wedge base, T-3.75 12VDC@1.2watts incandescent bulb standard
* Bulb holder is easy to install or remove
* 3 Terminals Button Actuator microswitch included
* Microswitch reliability tested to 10,000,000 cycles
* Microswitch can be replaced
* Polycarbonate lens cap for optical clarity
Dimensions:
* 60 mm Diameter x 72 mm Height
* Net weight: 100grams
* Mounting hole diameter: 24 mm
Page 13 Ocean Controls Catalog 2009
1
$27.50
5+
less 10%
1
$2.95
$2.95
$2.95
$2.95
5+
less 10%
less 10%
less 10%
less 10%
Push Button
Features:
Price Each
SFJ-011 Big Dome Push Button
5+
less 10%
Arcade Joystick - Long Handle
Arcade Joystick - Short Stick
Price Each
SFJ-003 Arcade Joystick- Short Handle
1
$4.25
1
$14.95
5+
less 10%
* Convex Button
* 35.75 mm Diameter x 46 mm Height
* M28 thread
* Mounting Hole Diameter: 27.3 mm
* Net weight: 0.015kg
Price Each
SFJ-015 Push Button 33mm-Blue
SFJ-016 Push Button 33mm-Green
SFJ-017 Push Button 33mm-Pink
SFJ-018 Push Button 33mm-Yellow
OCEAN CONTROLS - COMPONENTS
Blackberry Trackballer
Concave Button
Description: This is a 35mm
concave momentary push button similar to the ones you find on arcade games.
Simple screw in design. Perfect for mashing.
This button has a great tactile, 'clicky' feel.
Features:
* Concave plunger design
* Durable nylon material
* Microswitch: max 3A @ 120 VAC
* Microswitch reliability tested to 10,000,000 cycles
* Includes 3 terminal microswitch
* Net weight: 25g
Dimensions:
* Cap diameter: 35mm
* Overall height: 65mm
* Mounting hole: 1 1/8th inch paddle bit (1.125" / 28mm)
Price Each
SFJ-020 Concave Button – Red
SFJ-021 Concave Button – Blue
SFJ-022 Concave Button – Yellow
SFJ-023 Concave Button – Black
SFJ-024 Concave Button – White
SFJ-025 Concave Button – Green
1
$4.95
$4.95
$4.95
$4.95
$4.95
$4.95
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
Price Each
SFJ-030 Blackberry Trackballer
Circuit Breakers
1
$7.18
$7.18
$7.18
$7.18
$7.18
$7.18
$7.18
$7.18
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
Specifications:
All specifications at 25°C
Hold Current: 100% load indefinitely
Trip Current: Within 1 hr @ 135% load
Within 1 minute @ 200% load
Neon Voltage: 250V AC
Max. Voltage: 250V AC or 50V DC
Panel Cutout: 13.35mm x 28.5mm
Dimensions: 33H x 32L x 15.5W mm
Price Each
CIR-021 Circuit Breaker Switch 3A 250V
CIR-022 Circuit Breaker Switch 5A 250V
CIR-023 Circuit Breaker Switch 8A 250V
CIR-024 Circuit Breaker Switch 10A 250V
CIR-025 Circuit Breaker Switch 15A 250V
1
$7.23
$7.23
$7.23
$7.23
$7.23
5+
less 10%
less 10%
less 10%
less 10%
less 10%
Headerless ShiftBrite
Description:
Rotary - Linear
Series 3590
Resistance In Ohms 10K
Power (Watts) 2W
Number of Turns 10
Adjustment Type Side Adjustment
Tolerance ±5%
Package / Case Round - 0.875" Dia x 0.732" H
(22.23mm x 18.60mm)
Termination Style Solder Lug
Actuator Diameter 6.30mm
Actuator Length 20.62mm
Actuator Type Slotted Shaft
Page 14 Ocean Controls Catalog 2009
5+
less 10%
Combination illuminated switch and circuit breaker all in one compact
package.
10 Turn Potentiometers
Price Each
DIP-001 10 Turn 5K Potentiometer
DIP-010 15 Turn Dial Scale
1
$17.93
Illuminated Panel Mount Circuit Breaker
Specifications:
All specifications at 25°C
Hold Current: 100% load indefinitely
Trip Current: Within 1 hr @ 145% load
Within 1 minute @ 200% load
Max. Voltage: 250V AC or 50V DC
Panel Cutout: Single hole mount 12mm Ø
Dimensions: 36H x 31L x 15W mm
Price Each
CIR-001 Circuit Breaker 3A Panel Mount
CIR-002 Circuit Breaker 5A Panel Mount
CIR-003 Circuit Breaker 10A Panel Mount
CIR-004 Circuit Breaker 15A Panel Mount
CIR-005 Circuit Breaker 20A Panel Mount
CIR-006 Circuit Breaker 25A Panel Mount
CIR-007 Circuit Breaker 30A Panel Mount
CIR-008 Circuit Breaker 35A Panel Mount
Description:
This is a breakout board for our Blackberry Trackball. The
four
spindles on the trackball have a tiny circular magnet the end;
each of these are paired with an SMD hall effect sensor, which are used
to measure up, down, left and right movements of the trackball. An SMD
momentary switch is placed under the trackball to give you a select
switch. The BTN line will be pulled low when the switch is pressed.
Also included on the Trackballer are 4 LEDs: red, blue, green and white.
These can be powered to light the clear trackball up any color you can
imagine.
All features are broken out to a 0.1" pitch header. Regulated, 2.55.25VDC power must be provided to power the Hall sensors. The trackball is attached with strong CA glue. Board comes as shown, with all
components populated.
The hall-effect sensors and trackball combo are surprisingly sensitive. A
slight roll of the trackball creates multiple high/low transitions on the four
axis pins, easily picked up by any microcontroller. A 360° rotation of the
trackball, along a single axis, will result in
about 9 high/low transitions.
Features:
* Center select button
* 360° direction
* Hall effect sensors measure up/down/left/
right movements of trackball
* Red, blue, green, white LEDs to light up the
trackball
* All pins broken out to 0.1" pitch header
Dimensions: 1.1x0.85"
1
$27.50
$22.95
5+
less 10%
less 10%
Description:
The ShiftBrite is a module by
macetech that integrates the Allegro
A6281 3-channel constant current
LED driver with a large, highbrightness RGB LED. Using just three
digital output pins and a simple protocol, your microcontroller can control a
long chain of ShiftBrites. Each ShiftBrite in the chain can be independently changed to any of the
1,073,741,824 possible colors to create dynamic displays and decorations. Adjustable current for each color channel lets you correct for slight
differences in brightness. Overtemperature shutdown protects the LED
driver from overheating. The pins of the ShiftBrite are spaced 0.1" apart,
making them compatible with breadboards and perfboards.
Price Each
POL-1241 Headerless ShiftBrite
1
$8.65
5+
less 10%
OCEAN CONTROLS - COMPONENTS
Low Profile Crystals
Price Each
CRY-001 32.768kHz QSC38
CRY-004 8.0000MHz HC49S
CRY-006 16.0000MHz HC49S
CRY-008 20.0000MHz HC49S
Programmer Cables and ZIF Sockets
1
$3.50
$3.50
$3.50
$3.50
5+
less 10%
less 10%
less 10%
less 10%
1
$20.00
$25.00
$9.05
$9.05
$8.77
$14.55
PIC Micrcontrollers
Atmel AVR Micrcontrollers
Price Each
1
5+
ATL-001 AT89C2051-24-PC
$5.41
less 10%
ATL-002 ATTiny2313-10-PC 20MHz 2kb 8-bit
$13.95 less 10%
ATL-003 ATmega168-20PC 20MHz 16kb 8-bit Micro
$15.00 less 10%
ATL-004 ATmega162-16PU 16MHz 16kb 8-bit Micro $19.00 less 10%
ATL-005 ATmega32-16PI 16MHz 32kb 8-bit Micro
$24.00 less 10%
ATL-006 ATmega328-20PC 20MHz 32kb 8-bit Microcontroller $7.95 less 10%
Peripheral IC’s
Price Each
ICS-001 MAX232 RS232 Transceiver
ICS-002 LTC485 RS485 Transceiver IC
ICS-010 L297 Motor Controller IC
ICS-011 L298 Stepper Motor Controller IC
ICS-020 LM7805 5Volt Regulator
ICS-021 LM7812 12Volt Regulator
ICS-022 LM7833 3.3Volt 500mA Regulator
ICS-031 ULN2003 7 Darlington Array
ICS-032 ULN2803 8 Darlington Array
Price Each
ZIF-020 20 pin ZIF Socket
ZIF-040 40 pin ZIF Socket
USB-001 USB A Male to A Male Cable
USB-002 USB A Male to B Male Cable
CAB-002 DB9 Male to Female Cable
PLP-003 12VDC Unregulated Plug Pack
Price Each
PIC-001 PIC12C508A-04
PIC-002 PIC12C509A-04
PIC-005 PIC16F84A-20P
PIC-006 PIC16F88
PIC-007 PIC16F628A-20/P
PIC-008 PIC16F877A
PIC-010 PIC18F2550 USB 28pin microcontroller
1
$5.41
$5.41
$11.77
$13.59
$11.77
$13.59
$13.59
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
DIN Rail PCB Mounting Sections
1
$5.60
$4.25
$7.95
$8.25
$1.10
$1.10
$1.50
$3.20
$4.05
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
Easily mount 72mm or 107mm
wide PCBs on DIN rail, the total
PCB length that can be accommodated can be calculated by totalling
up the total length of the base sections and adding 10mm for each
end cap. Two mounting clips will be
required to attach the section to the
DIN rail.
For example:2 x 44.8mm bases
and 1x 11.2mm section + 2 endcaps = 44.8 +44.8+ 11.2 +10 +10 =
120.8mm.
DIN Rail Mounting Sections 72mm
Price Each
DRM-001 Base Mounting Clip
DRM-002 End Cap
DRM-003 Base Sections 11.2mm length
DRM-004 Base Sections 22.4mm length
DRM-005 Base Sections 44.8mm length
1
$1.77
$2.14
$2.86
$3.59
$4.32
10+
less 10%
less 10%
less 10%
less 10%
less 10%
DIN Rail Mounting Sections 107mm
Price Each
DRM-011 Base Mounting Clip
DRM-012 End cap
DRM-013 Base Sections 11.2mm length
DRM-014 Base Sections 22.4mm length
DRM-015 Base Sections 44.8mm length
Page 15 Ocean Controls Catalog 2009
1
$2.14
$2.50
$3.18
$3.91
$4.91
10+
less 10%
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - COMMUNICATIONS
ATEN USB to 2 Port and 4 Port RS232 Converter
The UC232A from ATEN is a USB to 2 Port or 4 Port serial RS232 converter. It provides PCs, notebook PCs and handheld computing devices
using USB an external PnP RS232 port
Features
Easy way to add 4 RS-232 serial ports
Fully compliant with USB 1.1; USB 2.0 compatible
Supports RS-232 serial interface
Supports automatic handshake mode
Up to 115.2 Kbps data transfer rate for each serial port
Supports remote wake up and power management
Dual data buffers for each upstream and downstream data transfer
Price Each
COV-014 USB to 2 Port Serial RS232 Converter
COV-015 USB to 4 Port Serial RS232 Converter
1
$79.00
$109.00
Non-Isolated USB to RS485/422 Converter
ATEN USB-RS232 Converter
The UC232A from ATEN is a USB to serial port converter. It provides
PCs, notebook PCs and handheld computing devices using USB an external PnP RS232 port
Features
Support the RS232 Serial interface.
Support full handshake mode
Full compliance with the USB Specification 1.1.
Up to 230Kbps data transfer rate.
Works with cellular phones, PDAs, digital cameras, modems or ISDN
terminal adapter.
OS Compatibility: WIN98, WIN ME, WIN 2K, WIN 2003, WIN XP, Windows Vista 32 & 64 Bit, LINUX and Mac OS 8.6/9/10.
Package Content
1x UC-232A, 1x Driver Disk, 1x User Manual
Price Each
COV-013 USB to Serial Converter
1
$29.00
Non Isolated RS232 to RS485 Converter
The USB485C is a USB to RS-485/422 industrial intelligent converter. It
isa good economical solution for the communication between USB and
RS-485/422. Compared with RS-232 to RS-485/422 converter, USB to
RS-485/422 converter has many advantages
Features
1.Small volume, easy installation
2.No power supply needed, plug and play
3.Adopt DIP switch setup, random switch RS485/RS-422 interface
4.Transmit distance reach up to 1800M at the
rate of 115200bps.
5.Automatic send data control, auto distinguish and sense direction
adopt data transfer
6.Auto sense serial signal rate, zero delay automatic transmit
Comes with a D9Female to Screw Terminal Interface
Suitable for Windows 98/ME/2000/XP/Linux OS/Vista (32bit)
Price Each
TOD-100 USB485C USB to RS485 converter
1
$69.95
Non-Isolated RS232 to RS485/RS422 Converter
The IC-485S converter can operate in:
RS422 mode: Point to point on 2 twisted pairs.
RS485 mode: Multidrop on one twisted pair
Simplex: when any device transmits, the others receive only
Features
• In RS485 mode, data transmission direction must
be controlled by the RTS Signal (i.e. it is not automatic).
For Automatic direction control see the units from Trycom.
• DCE/DTE Selectable
• Point to Point, Multidrop, and Simplex/Duplex Link Selectable
• Four Wire Full Duplex / Two Wire Half Duplex, D25 Female connector
• Supports baud rates up to 115.2kbps.
Data transfer can take place at up to 1200 metres over four or two wire
cable for full or half duplex, respectively.
In RS485 (2-wire) mode up to 32 receivers can be set up in a multidrop
installation, making for a cost effective network configuration.
The IC-485S can obtain power from the RS232 port.
For better line driving capability a mains Adaptor is included
Price Each
COV-002 Non-Isolated RS232 to RS422/RS485 Converter
Price Each
COV-020 ATEN IC-150 Short Haul Modem
Page 16 Ocean Controls Catalog 2009
1
$69.00
This simple RS232 to RS485 non isolated converter
features an auto baud rate up to 115200 bps
Features include
LED Indication:
Transmission Distance:9600 bps: 200M, 19200 bps:
200M, 38400 bps: 200M 57600 bps: 150M, 115200 bps:120M
Baud Rate: Up to 115200 bps
Operating Temperature: 0~55C, Storage Temperature: -10~70C
Operating Humidity: 20~95% RH (non-condensing)
Power Supply: Powerless or DV 5V
Serial Port: Screw Terminals RS-485x1, D9 Female RS-232x1
Price Each
ALT-010 Non Isolated RS232 to RS485 Converter
1
Isolated USB-RS422/RS485 converter
The USB-i485 module is a cost-effective way to
convert RS485 or RS422 industrial buses to a
USB interface. When connected to a PC USB port
the USB-i485 module is automatically detected
and is installed as a native COM port.
1500 Vdc isolation between the USB port and RS485/RS422 protects
the PC from spikes or possible misconnections in the communication
bus. The USB-i485 converter can be configured for four-wire (Full Duplex) RS422 and RS485 or two-wire (Half Duplex) networks. When operating in two-wire RS485 the data transfer control is automatically done
by the converter.
- Supports Windows 98/ME/2000/CE/XP/Vista, MAC & Linux 2.4.20 or
superior.
- Transmission rate: from 300 bps to 1Mbps.
Price Each
1
COV-001 Isolated USB to RS422/RS485 Converter $129.00
5+
less 10%
ATEN IC-150 Short Haul Modem
The IC-150 Short Haul Modem allows you to
connect the RS-232 ports of remote devices
for fast and easy file transfers and data sharing.
The unit drives your data at various speeds
up to 19,200 bps over distances up to 800m
using 24-gauge wire (transmitting at 110 bps
over distances up to 10km).
It provides 1,500VAC lighting surge protection and excellent noise rejection through the
use of differential circuitry. The unit is switch-selectable for DCE/DTE.
The Line Driver provides asynchronous transmission and operates full
duplex over four wires.
Features
No external power supply required
DCE/DTE selection
Long distance transfer via economical cable
1
Analog loop back
$69.00
Dimensions 74.5 x 54 x 18.5 (mm).
OCEAN CONTROLS - COMMUNICATIONS
USB to 2 RS232 and 2 RS485/RS422 ports Converter
USB2.0 to 1 RS232 and 1 RS485/RS422 Converter
The TRP-C08H allows you to simultaneously
connect 2 RS232 and 2 RS422/485 serial
devices to system by using a USB interface.
The RS232 interface support all common PC
DTE connection type. For RS422/485 data
lines TRP-C08H provides auto-detecting function in data format, baud rate and data direction flow control, it may automatically configure RS422/485 signals and baud rate without external switch setting.
- Full compliance with the USB V1.0, 1.1 and 2.0 specification.
- Expand to 2 standard RS232 ports and 2 RS422/485 ports.
- 256 bytes buffer for upstream and downstream data flow.
- Auto direction flow control on RS485.
- Automatically switch signal RS422 and RS485.
- Support 3000V DC isolation and surge protection on RS422/485 data
lines.
- Power/TXA/RXA/TXB/RXB mode LED indicator.
- Direct power from USB port and external power.
- Driver support: Windows 98/ME/2000/XP/CE3.0, Linux, and Mac OS.
The TRP-C08S is one standard USB 2.0 to
Serials Bridge that has one DB-9 RS232
male connectors and 4 PIN screw terminal
for RS422/485. The RS422/485 with auto
configuration in data format, baud rate and
RS485 data flow direction control.
RS422/485 equips with 3000VDC of isolation and internal surge-protection on each
data line, it gives the host computer and module itself entirely protection
from destructive voltage spikes and danger of unregulated voltages
input.
- Input: 2.0 protocol.
- Output: RS232 signal: Standard 9 pin DTE full-duplex.
- RS422 signal: Differential 4 full-duplex wires, RS485 signal: Differential 2 half-duplex wires (D+, D-).
- Driver support: Windows 98/ME/2000/XP/CE3.0, Linux, and Mac OS.
Price Each
1
TRY-005 USB-2 RS232 and 2 RS422/RS485 Converter $173.75
5+
less 10%
RS232/485/422 to Ethernet converter(10/100M)
Everything is being networked today but that doesn't mean your existing
equipment and software investment is out of date due to a lack of
Ethernet or TCP/IP connectivity. With 3onedata Express you can turn
any serial device into a network device instantly. Devices such as
CNCs, card readers, PLCs, switching machines, sensors, and UPS
systems can all have network connectivity.
3onedata Express supports Windows 95/98/Me, Windows NT, and Windows 2000/XP/2003 native COM drivers,
Features
1. Auto-detecting 10/100Mbps Ethernet interface
2. 3-in-1 RS-232/422/485 serial interfaces
3. Cigarette pack size for easy integration
4. Cupports Windows Native COM drivers with
automatic network connection recovery
5. Built-in Ethernet and TCP/IP protocol supports Driver Mode, TCP Server, TCP Client, UDP
6. RS-485 supports ADDC (Automatic Data Direction Control intelligence)
7. Built-in 15 KV ESD protection for all serial signals
Price Each
1
TOD-011 NP312 RS232/422/RS485 to Ethernet Converter (10/100M) $165.00
2 ports RS485/422 to Ethernet converter
Everything is being networked today but
that doesn't mean your existing equipment
and software investment is out of date due
to a lack of Ethernet or TCP/IP connectivity. With 3onedata Express you can turn
any serial device into a network device
instantly. Devices such as CNCs, card
readers, PLCs, switching machines, sensors, and UPS systems can all have network connectivity.
3onedata Express supports Windows 95/98/Me, Windows NT, and Windows 2000/XP/2003 native COM drivers,
Features
1. Auto-detecting 10/100Mbps Ethernet interface
2. Supports Windows Native COM drivers with automatic network connection recovery
3. Built-in Ethernet and TCP/IP protocol supports Driver Mode, TCP
Server, TCP Client, UDP
4. Built-in 15 KV ESD protection for all serial signals
Price Each
TOD-013 NP302-2M 2 Port RS485/422 to Ethernet Serial Server
Page 17 Ocean Controls Catalog 2009
1
$310.00
Price Each
TRY-014 USB-1 RS232 and 1 RS422/RS485
1
RS232/485/RS422 to Ethernet
Everything is being networked today but
that doesn't mean your existing equipment
and software investment is out of date due
to a lack of Ethernet or TCP/IP connectivity. With 3onedata Express you can turn
any serial device into a network device instantly. Devices such as
CNCs, card readers, PLCs, switching machines, sensors, and UPS
systems can all have network connectivity.
3onedata Express supports Windows 95/98/Me, Windows NT, and Windows 2000/XP/2003 native COM drivers,
Features
1. 3-in-1 RS-232/422/485 serial interfaces
2. Cigarette pack size for easy integration
3. Supports Windows Native COM drivers with automatic network connection recovery
4. Built-in Ethernet and TCP/IP 10M protocol supports Driver Mode, TCP
Server, TCP Client, UDP .
5. RS-485 supports Automatic Data Direction Control intelligence
6. Built-in 15 KV ESD protection for all serial signals
Price Each
1
TOD-010 NP311 RS232/422/RS485 to Ethernet Converter (10M) $115.00
2 ports RS232 to Ethernet converter
Everything is being networked today but that doesn't mean your existing
equipment and software investment is out
of date due to a lack of Ethernet or TCP/IP
connectivity. With 3onedata Express you
can turn any serial device into a network
device instantly. Devices such as CNCs,
card readers, PLCs, switching machines,
sensors, and UPS systems can all have
network connectivity.
3onedata Express supports Windows
95/98/Me, Windows NT, and Windows 2000/XP/2003 native COM drivers,
Features
1. Auto-detecting 10/100Mbps Ethernet interface
2. Supports Windows Native COM drivers with automatic network connection recovery
3. Built-in Ethernet and TCP/IP protocol supports Driver Mode, TCP
Server, TCP Client, UDP
4. Built-in 15 KV ESD protection for all serial signals
Price Each
TOD-012 NP302 2 Port RS232 to Ethernet Converter (10/100M)
1
$260.00
OCEAN CONTROLS - COMMUNICATIONS
RS232 To TTL Module
RS232 to RS422/RS485 Isolated Converter
The smallest and easiest to use serial conversion circuit on the market! This board has one
purpose in life - to convert RS232 to TTL and
vice versa (TX and RX). This will allow a microcontroller to communicate with a computer.
Shifter SMD is powered from the target application and can run at any voltage! That's right power the board at 5V and the unit will convert RS232 to 5V TTL.
Power the board at 2.8V and the Shifter board will convert RS232 to
2.8V CMOS TTL. Includes two indicator LEDs for TX and RX. Runs
from 300bps up to 115200bps.
Unit comes fully assembled and tested as shown. You can either solder a 4-pin header or individual wires. Dimensions: 1.25x1.15"
Model485P has both isolation and surge protection, enclosed terminal blocks for tamper resistance and DIP switches for configuration. Isolated power and ground generated internally.
LEDs indicate data traffic.
Features
1. Powered from double side, 2500V isolation,
1500W surge protection
2. Transmit distance can reach up to 1800M at the rate of 115.2kbps
3. Adopt interface atuo-adapt technology, no DIP switch setup,random
switcht RS-485/RS-422 interface
4. Automatic send data control, auto distinguish and sense direction
about data transfer
5. Auto sense serial signal rate, zero delay automatic transmit
Price Each
COV-201 RS232 To TTL Module
Point to point or multi-point, 2 line half duplex, 4 line full duplex
1
$14.95
5+
less 10%
Dual RS232 to RS422/RS485 Isolated Converter
Band rate 300-115200bps, automatic test signal rate
Powered by 9-15VDC plug pack.
The TRP-C06H allows 2 RS232 line
signal to be bi-directionally converted to
RS-422 or RS-485 standard and transmit
data up to 1.2KM . Featuring automatic
data format and baud rate detect function users just need to plug the unit and
go without extra configuration efforts.
TRP-C06H is equipped with 3000V DC
of isolation and internal surge protection
to protect the host computer and converter against high voltage spikes,
as well as ground potential differences. DIN Rail Mount Option
Features Include
- 10-30VDC power supply.
- Automatic data format configuration.
- Auto direction flow control on RS-485.
- Auto baud rate switching from 300bps to 115.2Kbps.
- 3000V DC isolated protection.
- Surge protection on RS-422/485 data lines.
- Power/TX/RX mode LED indicator.
- Support screw terminal and external DC adaptor.
Price Each
1
TOD-001 RS232 to RS422/RS485 Isolated Converter $75.00
Price Each
1
5+
TRY-002 Dual Isolated RS232 to RS422/RS485 Converter $119.00 less 10%
Band rate 300-115200bps, automatic test signal rate
Working temperature -40 to 80degC
TRP-C07 is designed to extend the RS422 and RS-485 signals to another 4000ft
( 1200m ) distance and increase the maximum number of connected nodes up to 32
sets. Aside from extension function TRPC07 provides with auto configuration features in data format detecting, baud rate setting and RS-485 data direction flow control. TRP-C07 is equipped with photo-couplers and internal
surge protection to protect the module and all data lines against high
voltage spikes, as well as ground potential differences. DIN Rail mount
option available.
- 10-30VDC power supply.
- Automatic data format configuration.
- Auto direction flow control on RS-485.
- Auto baud rate switching from 300bps to 115.2Kbps.
- RS485 bi-directionally communication.
- 3000 VDC isolated protection.
- Surge protection on RS-422/485 data lines.
- Power/TX/RX mode LED indicator.
- Support screw terminal and external DC adapter.
- DIN rail or panel mount support.
Page 18 Ocean Controls Catalog 2009
RS232 to RS422/RS485 Isolated Converter
SW485SGI/C is our top-of-the-line RS232 to RS485/422 converter with
both isolation and surge protection, enclosed terminal blocks for tamper
resistance and dip switches for configuration. Isolated power and ground
generated internally. LEDs indicate data traffic.
Features
1. DIN-rail mount, terminal block, 9-36VDC
external power, 3000V isolation
2. Transmit distance reach up to 1800M at the
rate of 9.6kbps
3. random switch RS-485/RS-422 interface
4. Automatic send data control, auto distinguish and sense direction about data transfer
5. Auto sense serial signal rate, zero delay automatic transmit
Point to point or multi-point, 2 line half duplex, 4 line full duplex
Price Each
1
TOD-002 RS232 to RS422/RS485 Isolated Converter $139.00
RS485/RS422 Repeater
Price Each
TRY-003 RS422/RS485 Isolated Repeater
5+
less 10%
1
$84.00
5+
less 10%
5+
less 10%
USB to RS232/RS485/RS422 Converter
The TRP-C08 allows you to connect your serial devices to systems by
using a USB interface. With auto configuration in data format, baud rate
and RS485 data flow direction control. TRP-C08 is equipped with 3000V
DC of isolation and internal surge-protection on each data lines to protect the host computer and converter
against high voltage spikes, as well as
ground potential difference.
Features include
- Full compliance with the USB V1.0 and
2.0 specification.
- System gets 1 COM port when the
converter is connected.
- Auto data format detecting.
- Auto direction flow control on RS485.
- Auto baud rate switching from 300bps to 115.2 Kbps.
- Driver support: Windows 98/ME/2000/XP/CE3.0, Linux and Mac OS.
Price Each
TRY-004 USB-RS232/RS422/RS485 Isolated Converter
1
$88.75
OCEAN CONTROLS - COMMUNICATIONS
4 ports RS232 to Ethernet converter
4 ports RS485/422to Ethernet converter
Everything is being networked today but that doesn't mean your existing
equipment and software investment is out of date due to a lack of
Ethernet or TCP/IP connectivity. With 3onedata Express you can turn
any serial device into a network device instantly. Devices such as
CNCs, card readers, PLCs, switching machines, sensors, and UPS
systems can all have network connectivity.
3onedata Express supports Windows 95/98/Me, Windows NT, and Windows 2000/XP/2003 native COM drivers,
Features
1. Auto-detecting 10/100Mbps
Ethernet interface
2. Supports Windows Native COM
drivers with automatic network connection recovery
3. Built-in Ethernet and TCP/IP protocol supports TCP Server,
TCP Client, UDP Server/Client.
4. Built-in 15 KV ESD protection for all serial signals
Everything is being networked today but that doesn't mean your existing
equipment and software investment is out of date due to a lack of
Ethernet or TCP/IP connectivity. With 3onedata Express you can turn
any serial device into a network device instantly. Devices such as
CNCs, card readers, PLCs, switching machines, sensors, and UPS
systems can all have network connectivity.
3onedata Express supports Windows 95/98/Me, Windows NT, and Windows 2000/XP/2003 native COM
drivers,
Features
1. Auto-detecting 10/100Mbps
Ethernet interface
2. Supports Windows Native
COM drivers with automatic network connection recovery
3. Built-in Ethernet and TCP/IP protocol supports TCP Server,
TCP Client, UDP Server/Client.
5. Built-in 15 KV ESD protection for all serial signal
Price Each
TOD-014 NP304 4 RS232 to Ethernet Serial Server
1
$515.00
Embedded Serial Server Module
Everything is networked is rapidly becoming the norm for enterprises the
world over, and to keep pace with the trend of networked-based automation, devices must be networked in order to form an automatic data collection system for quality control, production monitoring, or even realtime cost management. But that doesn't mean your existing equipment
and software investment is out of date due to a lack of Ethernet or TCP/
IP connectivity. With 3onedata Express, devices such as CNCs, milling
machines, card readers, PLCs, switching machines, sensors, and UPS
systems will become powerful tools with network connectivity.
Features
1. Adopt TTL
2. 3-in-1 RS-232/422/485 serial interfaces
3. Supports Windows Native COM drivers with automatic network connection
recovery
4. Built-in Ethernet and TCP/IP protocol
supports Driver Mode, TCP Server, TCP Client, UDP
5. RS-485 supports ADDC (Automatic Data Direction Control intelligence)
6. Built-in 15 KV ESD protection for all serial signals
Price Each
TOD-030 M4000T Serial Server Module
TOD-031 M4000T Test Motherboard
1
$55.00
$45.00
Model FL45 RJ45 Ethernet Surge Protector
IEC6 1000-4-5 and ITU-TK20&K21 are the recognized standards for top
quality surge protectors. The FL45 complies with these standards. The
FL45 is constructed with high response surge arresters, this allows
clamping of high voltage transients and low loss against high speed
signal, because it has a low capacitance. Designed to protect data communication lines in local and wide area networks up to 100Base-T transmission speeds.
Features
1.IEC6 1000-4-5 and ITU-TK20&K21
2.The high response surge arresters
3.Clamping voltage and low loss against high
speed signal
4.Designed by the theory of current limited and
voltage clamped, discharged to ground
5. Standard: 10Base-T/100Base-T standard
Price Each
TOD-022 FL45 RJ45 Ethernet Surge Protection
1
$45.00
Price Each
TOD-021 FL-BNC BNC Surge Protection
Page 19 Ocean Controls Catalog 2009
Price Each
TOD-015 NP304-4M RS485/422 to Ethernet Serial Server
1
$580.00
Model 233I RS232 Isolator
Model232I is a RS232 system communication serial port optic isolation
product. This product supports transmission rate as high as 57,600bps,
no external power needed, optic electric isolation 5KV and is applicable
in tough environments. According to different customer needs, there are
4 lines, 6 lines and 8 lines three types, separately corresponds to three
line serial port application, five lines serial port application and 7 lines
serial port application with RTS/CTS (or DTR/CTS). Transmission distance at 9,600bps is 10m, stable performance.
Features
1.Plug and play
2.Port-powered, lowest consumption
3.Auto sense serial signal rate
4.Isolation serial device
Price Each
TOD-003 Model232I RS232 to RS422/RS485 Isolated Converter
1
$35.00
Model FL485 RS485 Isolator
IEEE 1000-4-5 and ITU-TK20 & K21 are the recognized standards for
top quality surge protectors. The FL485 unit meet these specifications
with three stage protection on all data lines. The FL485 has high response speed and high transfer performance . All have #10 ground
screws which must be connected to a solid
ground.
Features
1.Three stages of protection on every data line
2.Protected signal ground connection
3.RS-422, RS-485 versions
4.Easy to install
Price Each
TOD-020 Model FL485 lighting protection
1
$35.00
Model FLBNC - BNC Ethernet Surge Protector
IEC6 1000-4-5 and ITU-TK20&K21 are the recognized standards for top
quality surge protectors. The FLBNC complies with these standards.
The FLBNC is constructed with high response surge arresters, this allows clamping of high voltage transients and low loss against high speed
signal, because it has a low capacitance. Designed to protect the equipment and coaxial line, connect in series. Interface accord with BNC
standard.
Features
1.IEC6 1000-4-5 and ITU-TK20&K21
2.Allowed clamping voltage and low loss
against high speed signal
3.low capacitance. Designed to protect the
equipment and coaxial line, connect in series
1
4.Interface accord with BNC standard
$45.00
OCEAN CONTROLS - COMMUNICATIONS
Ethernet to RS232/RS422/RS485 Isolated Converter
TRP-C36 is designed to instantly convert
data from RS-232/422/485 interfaces to an
Ethernet network running at the TCP/IP,
UDP protocol. By using a standard COM
port and existing network infrastructure the
device allow you to link together a distant
RS-232/422/485 serial device. You can
reach TRP-C36 from Windows and Linux
without the need to modify existing software. TRP-C36 supports 10/100Mbps auto-detecting, and auto RS-485
data direction flow control, it also provides with 3000V DC isolation and
internal surge protection to protect the converter against high input voltage spikes and ground potential differences, and ensure a save data
transmission on network. DIN Rail mount option available.
Features include
- 10-30VDC power supply.
- Fully compatible with Ethernet TCP/IP protocol.
- Support 3000V DC isolation protection.
- Auto direction flow control on RS-485.
- Surge protection on RS-422/485 data lines.
- Support baud rate up to 230Kbps.
- Power/Link/TX /RX mode LED indicator.
- Support intranet and internet system setting function.
- Support screw terminal and standard external DC power adaptor.
- Operating System: Windows98/Me/2000/NT/XP.
Price Each
TRY-010 Ethernet to RS-232/422/485 Isolated Converter
1
$151.25
Fiber to RS232/RS422/RS485 Isolated
Converter ST Multi Mode
The TRP-C39 fiber converter allows RS232/422/485 signals to be bi-directionally
converted to fiber optic and extend the distance up to 2KM over multi-mode. By using
fiber optic transmission technology TRP-C39
secures a stable and error free data transmission over the industrial environments present
electrical noise and ground differential challenges, especially over long distances. TRP-C39 support data format,
baud rate and data direction auto configuration, it also provides with
3000V DC isolation and internal surge protection. The industry DIN rail
and panel mounting design enable user a fast and professional installation. DIN Rail Mount Option
Features Include
- 10-30VDC power supply.
- Wide range power input voltage.
- ST Multi-mode fiber port.
- Auto direction flow control on RS-485.
- Automatically switch signal RS-232, RS-422 and RS-485.
- Support 3000V DC isolation protection.
- All RS-422/485 signals provide surge and over current protection.
- Power/TX/RX mode LED indicator.
- Fiber transmission distance up to 2KM .
- Auto baud rate switching from 300bps to 115.2Kbps.
Price Each
TRY-012 Fiber to RS-232/422/485 ST Multi-mode
DIN RAIL OPTION FOR
TRYCOM COMMUNICATION MODULES
Price Each
TRY-900 DIN Rail Mount
1
$15.00
5+
$13.50
1
$132.50
Modbus TCP/IP to ASCII/RTU Gateway
The TRP-C 31M , MODBUS gateway allows MODBUS RTU/ASCII devices to operate on a MODBUS TCP network. It allows either MODBUS
serial master or slave to communicate with MODBUS TCP’s slave or master.
When TRP-C 31M function as “MODBUS TCP masters to RTU/ASCII
slaves”: It allows multiple MODBUS TCP masters to communicate with a
MODBUS serial network. the queries from different masters are pipelined
and processed one by one. When TRP-C 31M functions as MODBUS
RTU/ASCII master to MODBUS TCP slaves: it can connect up to 8 MODBUS TCP slaves.
User can specify a UID range for each MODBUS TCP slave. TRP-C 31M
provides inactive timeout that allows user to specify a time period to disconnect TCP/IP connection to prevent one connection slot was occupied if
there is no activity in the network., or prevent any another connection
again. A friendly management software provides user an easy way of
configuration over Ethernet. TRP-C 31M can work at Loop back Mode, all
data is sent back immediately. This feature makes the connection testing
easy. DIN Rail mount option available.
Features include
- 10-30VDC power supply.
- Supports 10/100 Mbps Ethernet.
- Supports RS232, RS422, and RS485
serial interface.
- High speed up to 230.4Kbps
- Supports 8 MODBUS TCP master to
MODBUS RTU/ASCII slave (up to 31) .
- Supports MODBUS RTU/ASCII master to
MODBUS/TCP slave devices (up to 8).
- Provide inactive timeout for connection auto-recovery when power failures.
- Automatically generate exception when RTU/ASCII slave device does
not response.
- Remote IP address filtering function to reject unwanted incoming connection source.
Price Each
TRY-007 Modbus TCP To RTU/ASCII Gateway
Ethernet to Fiber Media Converter
TRP-C41 is a device for Ethernet extension over fiber, it supports pointto-point and networked systems. The high fiber bandwidth connections
solve problems with electrical noise and different ground potentials over
long transmission lines. TRP-C41 supports 10/100Base-TX transmissions up to 100 meters and 100Base-FX transmissions up to 20KM . It is
the perfect solution for wide distance connections with high immunity to
electrical noise.
Features include
- Cable: Fiber cable (9/125um).
- One 10/100Base-TX auto-negotiation
Ethernet RJ-45 port.
- One 100Mbps fiber port with Single-mode
SC connector.
- Built in 128Kb RAM for data buffer.
- Wavelength: 1310 nM.
- Fiber Power:-15 ~ -8 dBm.
- LED indicator: Power and power and TX and fiber link/activity, full/half,
10/100MB.
- Distance : 20KM can be up to 60KM (option).
- Speed : Auto 10/100MB.
- Power Consumption: 12V/160mA.
- Power requirement: USB port power or DC input or screw terminal
from +10 to 30V.
- Operating temperature: 0 to 55degC.
Price Each
TRY-041 Ethernet to Fibre Converter
Page 20 Ocean Controls Catalog 2009
1
$233.75
1
$166.25
OCEAN CONTROLS - COMMUNICATIONS
Fiber to RS232/RS422/RS485 Isolated
The TRP-C39S fiber converter allows RS-232/422/485 signals to be bidirectionally converted to fiber optic and extended the line signal distance up to 40KM over single mode. By using fiber optic transmission
technology TRP-C39S secures a stable and error free data transmission
over the industrial environments. The high bandwidth fiber connections
solve problems with electrical noise and different ground potentials over
long transmission. TRP-C39S support auto configuration in data format,
baud rate and RS-485 data direction flow control, it also provides with
3000V DC isolation and internal surge
protection. DIN Rail mount option available.
Features include
- 10-30VDC power supply.
- SC single mode fiber port.
- Auto direction flow control on RS-485.
- Auto RS-232/422/485 signals switching.
- Auto data format detecting.
- Auto baud rate switching from 300bps to 115.2Kbps.
- Support 3000V DC isolation protection.
- Support surge protection on RS-422/485 data lines.
- Power/TX/RX mode LED indicator.
Price Each
TRY-013 Fiber to RS-232/422/485 SC Single-mode
433MHz Long Range Radio from HAC. These small modems use a
seamless serial interface - whatever enters the TX pin at 9600bps
shows up on the other unit's RX pin. All buffering and error detection is
handled internally. And the best part - with 10mW output, it reaches over
500m!
This unit can be attached to TTL level serial (for microcontrollers) or
directly to RS232 for incredibly simple serial
cable replacement!
Specifications:
* Operating Voltage: 3.3V-5.5V
* 9600bps over 500m
* Modulation type: GFSK
* 8 Channels jumper selectable
* Low power : 30mA RX, 40mA TX, 20uA
Sleep
* Small footprint size: 26x47mm
Supported Antennae: Kit comes with 1/4 wave 50Ohm antenna and
communications cable!
1
$222.50
Price Each
WIR-001 Modem Long Range 433MHz: UM96
5+
less 10%
The KT-5232 is an easy to use adapter for the UM96 and UM12 wireless
modems.
Just attach the modem, a power supply (8-30VDC) and a serial cable
and you will be up and running in no time.
Use a Male to Female 9-pin serial
The BlueSMiRF is the latest Bluetooth
wireless serial cable replacement. These
modems work as a serial (RX/TX) pipe.
Any serial stream from 9600 to 115200bps
can be passed seamlessly from your computer to your target. We've even tested
these units successfully over open air at
350ft (106m)!
Specifications:
* Operating Voltage: 8-30V
* Accepts UM12 and UM96 modems
* D9F Connector
The remote unit can be powered from
3.3V up to 6V for easy battery attachment.
All signal pins on the remote unit are 3V6V tolerant. No level shifting is required.
The BlueSMiRF includes hardware flow control (CTS and RTS) and
uses a compact ceramic antenna.
Specifications:
* FCC Approved Class 1 Bluetooth Radio Modem
* Extremely small radio - 0.15x0.6x1.9"
* Very robust link both in integrity and transmission distance (100m) no more buffer overruns!
* Low power consumption : 25mA avg
* Hardy frequency hopping scheme - operates in
harsh RF environments like WiFi, 802.11g, and
Zigbee
* Encrypted connection
* Frequency: 2.4~2.524 GHz
* Operating Voltage: 3.3V-6V
* Serial communications: 2400-115200bps
* Operating Temperature: -40 ~ +70C
* Built-in antenna
Use a Bluetooth USB Dongle to communicate between a PC and the
modem
1
$89.95
$22.68
5+
less 10%
less 10%
Price Each
KTA-232 Wireless Modem Adapter for UM96 and UM12
1
$20.00
Modem Long Range 433MHz: UM12 - Includes Antenna
and Cable
433MHz Long Range Radio from HAC. These
small modems use a seamless serial interface
- whatever serial character enters the TX pin at
1200bps shows up on the other unit's RX pin.
All buffering and error detection is handled
internally. And the best part - with 10mW output, it reaches over 1000m!
This unit can be attached to TTL level serial
(for microcontrollers) or directly to RS232 for
incredibly simple serial cable replacement!
Specifications:
* Operating Voltage: 3.3V-5.5V
* 1200bps over 1000m
* Modulation type: GFSK
* 8 Channels jumper selectable (4 can be used in Australia 433MHz
and above)
* Low power : 30mA RX, 40mA TX, 20uA Sleep
* Small footprint size: 26x47mm
Documents: HAC-UM96 Datasheet (Serves both UM96 and UM12)
Supported Antennae: Kit comes with 1/4 wave 50Ohm antenna and
communications cable!
Price Each
WIR-002 Modem Long Range 433MHz: UM12
Page 21 Ocean Controls Catalog 2009
1
$69.95
UM96 and UM12 Modem Adapter
Bluetooth Modem
Price Each
WIR-010 Bluetooth Modem
TRY-901 USB-Bluetooth Dongle
Modem Long Range 433MHz: UM96 - Includes Antenna
and Cable
1
$79.00
5+
less 10%
OCEAN CONTROLS - COMMUNICATIONS
Bluetooth® Modem - Roving Networks RS232
Transceiver - 2.4GHz with Duck Antenna
The MiRF v2 is the latest in RF modules. This module uses the newest
2.4GHz transceiver from Nordic Semiconductor, the nRF24L01. This transceiver IC operates in the 2.4GHz band
and has many new features! Take all
the coolness of the nRF2401A and
add some extra pipelines, buffers, and
an auto-retransmit feature - very
nice! This also board features a reverse polarized SMA connector for
maximum RF range. Please remember, you will need a mating RP-SMA
2.4GHz antenna (listed below).
Description: FireFly is a Roving Networks' RN-41 Bluetooth® module
with RS232 circuitry on the front end. This allows the user to access the
RN-41 AT command set over a common COM port. FireFly enables
wireless connections to any legacy serial port and supports bi-directional
RS-232 (or 422 !) signaling at a rate of up to 464Kbps. Just attach FireFly to your device's RS232/EIA232/422 port, power it, and you're connected. The transmit range can be up to 330' (100m), depending upon
environmental considerations.
Please note: The power jack on the side of the unit is a small 3.5x1.2mm
jack. The center pin is positive and requires 5-11VDC.
Features:
Comes with 2.4GHz Duck Antenna 2.2dBi with Reverse Polarized SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm
impedance. 4" long.
Features:
* On-board 3.3V LDO Regulator (3.3 to 7V supply allowed)
* 80m Range at 1000kbps
* 2Mbit Data Rate
* Auto Acknowledge
* Auto Re-Trasmit
* Multiceiver - 6 Data Pipes
* 32 Byte seperate TX and RX FIFOs
* 5V tolerant input pins
* Software selectable channel from 2400MHz to 2525MHz (125 Selectable channels)
* Minimum number of external components
* Pins broken out : VCC, CE, CSN, SCK, MOSI, MISO, IRQ, GND
* Lots of application notes and support on Nordic Semiconductor Website
* Operating Voltage: 3V
* Output Power: +4dBm
* Data Rate: 1Mbps; 250Kbps
* Small footprint size: 20.0 x 36.7 x 2.4mm
* Operating Temperature: -40 ~ +85 C
* Long range: 280mts @250Kbps ; 150mts @1Mbps
* Built-in antenna
Price Each
WIR-006 Transceiver - 2.4GHz with Duck Antenna
1
$36.95
5+
less 10%
Serial UHF Transmitter and Receiver Pair
This transmitter and receiver pair is good for
data rates up to 4800bps and distance up to
160metres
The receiver is operated at 5V and the transmitter operates from 2-12V. The higher the Voltage,
the greater the range
This is an ASK transmitter module with an output of up to 8mW depending on power supply
voltage. The transmitter is based on SAW resonator and accepts digital inputs, can operate
from 2 to 12 Volts-DC, and makes building RF enabled products very
easy.
This receiver has a sensitivity of 3uV. It operates from 4.5 to 5.5 voltsDC and has digital output. The typical sensitivity is -103dbm and the
typical current consumption is 3.5mA for 5V operation voltage. Modulate
Mode ASK
Frequency range—433.92MHz
Price Each
WIR-030 Serial UHF Transmitter Receiver pair
Page 22 Ocean Controls Catalog 2009
1
$11.50
5+
less 10%
* Wireless cable replacement: use to
replace cables or where cabling is not
possible or practical
* Very low power consumption (<5ma
idle, 10-40ma connect)
* Bluetooth® Technology v2.0 compliant
* FCC, IC, CE certified, and RoHS compliant
* Class 1 high powered radio for long
range operation
* Easy to use settings via on board DIP switches
* RS232 driver built in
FireFly uses the standard Bluetooth Serial Port profile and is compatible
with all clients running under Windows™, PalmOS™, PocketPC™, Apple™, and other Bluetooth® enabled platforms.
Price Each
1
5+
WIR-011 Bluetooth Modem - Roving Networks RS232 $149.00 less 10%
Serial UHF Transmitter and Receiver
This transmitter and receiver pair have a usable
range up to 30m
Supply Voltage 5VDC
Transmission Data rate 8KB/sec
Receiver Data rate 4.8KB/Sec
Modulate Mode ASK
Frequency range—433.92MHz
Price Each
WIR-020 Serial UHF Transmitter
WIR-021 Serial UHF Receiver
1
$9.05
$9.05
5+
less 10%
less 10%
RS485 Distribution Board
This card allows you to connect several
RS485 devices. These have been primarily
designed to connect the Moscad Ace RTU
RS485 port via an RJ45 connector. It allows
multiple devices such as VSD drives, PID
controllers etc to be connected together. Up to
4 devices can be connected via terminals. The
RJ45 cable can be provided to allow connection to a Moscad RTU.
Can be purchased with a DIN Rail Mount.
Price Each
OCH-012 RS485 Distribution Card in DIN Rail Mount
1
$45.00
OCEAN CONTROLS - COMMUNICATIONS
XBee 2mW Series 2.5 Wire Antenna
XBee Pro 60mW Wire Antenna
New 2.4GHz XBee XB24-BWIT-004 module from
Digi (formally Maxstream). Series 2.5 improves on
the power output and data protocol. These modules
take the 802.15.4 stack (the basis for Zigbee) and
wrap it into a simple to use serial command set.
They allow a very reliable and simple communication between microcontrollers, computers, systems,
really anything with a serial port! Point to point and multi-point networks
are supported.
Series 1 and Series 2.5 XBee modules have the same pin-out. However,
Series 1 modules cannot communicate with new Series 2.5 modules.
Features:
* 3.3V @ 40mA.
* 250kbps Max data rate
* 2mW output (+3dBm)
* 400ft (120m) range
* Built-in antenna
* Fully FCC certified
* 6 10-bit ADC input pins * 8 digital IO pins
* 128-bit encryption
* Local or over-air configuration
* AT or API command set
Price Each
WIR-041 XBEE 2mW Wire Antenna
1
$46.95
5+
less 10%
These 2mm 10-pin Sockets accept the XBee Modules
and solder into the breakout board (above) so you don't
have to permanently solder the XBee module to the
breakout board.
1
$1.59
1
$79.95
5+
less 10%
XBee Explorer USB Board
Price Each
WIR-045 XBEE Explorer USB Board
1mW Series 1 Wire Antenna
1
$37.50
XBee Breakout Board
XB24-AWI-001 module from Digi. Please Note: Series 1
and Series 2.5 XBee modules have the same pin-out.
Series 1 modules cannot communicate with Series 2.5
modules.
Price Each
WIR-046 XBee 1mW Series 1 Wire Antenna
Price Each
WIR-042 XBEE Pro 60mW Wire Antenna
This is a simple to use, USB to serial base unit for the
XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini
USB cable, and you will have direct access to the serial
and programming pins on the XBee unit.
2mm 10-pin Sockets for XBee Breakout
Price Each
WIR-043 XBEE 2mm 10pin Socket
The very popular 2.4GHz XBee XBP24-AWI-001
module from Digi (formally Maxstream). The Pro
series have the same pinout and command set of
the basic series with an increase output power of
60mW! These modules take the 802.15.4 stack (the
basis for Zigbee) and wrap it into a simple to use
serial command set. They allow a very reliable and
simple communication between microcontrollers, computers, systems,
really anything with a serial port! Point to point and multi-point networks
are supported.
Features:
* 3.3V @ 215mA
* 250kbps Max data rate
* 60mW output (+18dBm)
* 1 mile (1500m) range
* Built-in antenna
* Fully FCC certified
* 6 10-bit ADC input pins
* 8 digital IO pins
* 128-bit encryption
* Local or over-air configuration
This is a simple breakout board for the popular XBee
product from Maxstream. This board breaks out all 20
pins of the XBee to a 0.1" standard spacing dual row
header. The spacing between 0.1" headers is 0.5"
making it breadboard DIP friendly. We highly recommend using the female sockets to avoid having to
solder the XBee permanently to the breakout board.
This is the PCB only. Please order the accompanying
2mm sockets (you'll need 2!) and 0.1" headers below.
1
$39.95
XBee Pro 50mW Series 2.5 Wire Antenna
XBP24-BWIT-004 module from Digi.
Please Note: Series 1 and Series 2.5 XBee modules
have the same pin-out. Series 1 modules cannot communicate with Series 2.5 modules.
Price Each
WIR-040 XBEE Breakout board
1
$3.95
5+
less 10%
XBee Explorer Serial
Price Each
1
WIR-047 XBee Pro 50mW Series 2.5 Wire Antenna $79.95
5+
less 10%
XBee Pro 50mW Series 2.5 RPSMA Connector
XBP24-BSIT-004 module from Digi. Please Note: Series
1 and Series 2.5 XBee modules have the same pin-out.
Series 1 modules cannot communicate with Series 2.5
modules.
Price Each
WIR-048 XBee Pro 50mW Series 2.5 RPSMA Connector
Page 23 Ocean Controls Catalog 2009
1
$84.95
Description: This is a simple to use,
RS232 to serial base unit for the XBee line.
This unit works with all XBee modules including the
Series 1 and Series 2.5, standard and Pro version.
Plug the unit into the XBee Explorer, attach a RS232
cable, and you will have direct access to the serial and programming
pins on the XBee unit. The board also supports DTR communication so
you can reprogram and configure the XBee unit.
Price Each
WIR-049 Xbee Explorer Serial
1
$39.00
5+
less 10%
OCEAN CONTROLS - DATA LOGGERS
TagTemp Temperature Logger
TagTemp Temperature Logger Starter Pack
TagTemp is a compact water proof
temperature data logger. Housed in an IP67 enclosure, TagTemp can be installed in harsh environments in different applications.
It can be easily programmed and set via a handy
infrared IR-LINK 3 interface connected to a USB
port under Windows LogChart II software or with a
Palm compatible PDA IrDA interface under PalmOS. Features
- Enclosure: IP67, flame retardant, ABS+PC
- Dimensions: 47 x 30 x 12 mm;
- Temperature measurement accuracy: ±0.5 ºC;
- Reading resolution: 14 bits or 16,384 levels;
- Memory capacity: 16,000 loggings;
- Reading intervals: from 1 second to 18 hours;
- Loggings can be programmed to start immediately, outset by the device’s button, by date/hour or by a programmed setpoint or through a
PDA;
- Loggings can be programmed to stop: at full memory; at some specified date and hour, number of samples or never (circular memory);
- Internal button to command start/stop logging;
Price Each
LOG-010 TagTemp 16K Readings
LOG-002 IR-Link & Windows LogChart II
1
$99.00
$120.00
5+
less 10%
less 10%
Logbox-RHT and LogBox-RHT-LCD Data Logger
Are dual channel data loggers with built-in
temperature and relative humidity sensors. They
use a high quality industrial grade humidity sensor
for accurate and reliable operation in applications
such as transportation, food and goods storage,
process auditing, pharmaceutical, HVAC and
others.
They can be easily programmed and set via a
handy infrared IR-LINK 3 interface connected to a
USB port under Windows® software or with a PalmOS compatible PDA
IrDA interface. LogChart II software allows for logger configuration, recorded data retrieval, plotting, historical analysis and it exports data to
spread sheets.
In the LogBox-RHT-LCD the temperature and humidity values are
shown in the digital display. You can also check on the display the Minimum and maximum recorded values.
Price Each
LOG-005 LogBox RHT 32K Readings
LOG-006 Logbox RHT 32K Readings with LCD
LOG-002 IR-Link & Windows LogChart II
1
$289.00
$309.00
$120.00
5+
less 10%
less 10%
less 10%
LogBox AA Data Logger
Is a 2-channel data logger which can accept 020mA and 4-20mA, 0-50mV and 0-10V voltage, thermocouple, Pt-100 RTD signals inputs
all in a small weatherprooof IP65 enclosure.
Setup and data retrieval is done in a PC via an
infrared wand through the use of LOG CHART,
a Windows compatible software which plots
and prints graphs, lists loggings and exports
data to spreadsheets.
Memory capacity: 32k readings
The LogBox-AA also provides a signal for commanding an external
power supply (battery) of a device connected to the logger. This feature
allows that external devices, such as a transmitter, be powered
only during the measurement sample time, thus extending the life
of these external batteries.
Price Each
LOG-001 LogBox AA 32K Readings
LOG-002 IR-Link & Windows LogChart II
Page 24 Ocean Controls Catalog 2009
1
$269.00
$120.00
5+
less 10%
less 10%
Contains 2 Tagtemp Dataloggers, a USB-IRLink and
Logchart software. All you
need to get you started for
$199.00
Price Each
LOG-011 TagTemp Starter Pack
1
$239.00
LogBox DA Logger
Is a 2 channel data logger
Channel 1: NPN, PNP, Pulse or Dry Contact
Max. frequency: 4000 Hz or 20 Hz Maximum
counting: 65,535 per period.
Channel 2: 0-20mA, 4-20mA, 0-50mV and 010Vdc
Memory capacity: 32k readings
The LogBox-DA also provides a signal for
commanding an external power supply
(battery) of a device connected to the logger. This feature allows that
external devices, such as a transmitter, be powered only during the
measurement sample time, thus extending the autonomy of these
external batteries.
This logger has been designed for monitoring water and irrigation flows
but is suitable for many other applications
Price Each
LOG-003 LogBox DA 32K Readings
LOG-002 IR-Link & Windows LogChart II
1
$249.00
$120.00
5+
less 10%
less 10%
Field Logger
A stand-alone data logger which features 8
universal analogue inputs and will operate
as a datalogger or as an RTU (Remote
Telemetry Unit using Modbus Protocol)
linked to a PC for on line recording and
supervision. Able to be mounted on a DIN
rail, its 8 universal channels accept t/c J,
K, T, E, N, R, S, B; 4-20mA, Pt100, 050mV without hardware change. Connection to the input channels are via screw terminals. The Fieldlogger also
features 2 alarm relay channels.
The Fieldlogger is setup by the Configurator software. The Fieldlogger
has a RS485 interface which allows communication to 1Km. A connection from the PC's RS232 port is made via a RS232/ RS485 converter.
Features include
Internal memory (optional) for 128,000 recordings and real time clock.
Input resolution: 12,000 levels.
Accuracy: 0.1% of full scale.
Price Each
LOG-102 FieldLogger Datalogger 128k memory 24VDC
LOG-104 FieldChart Data Acquisition Software - 8 Channels
1
$750.00
$275.00
OCEAN CONTROLS - DATA LOGGERS
Logomatic V2 Serial Data Logger
Venus GPS with SMA Connector
Description: This is a development
board that uses the smallest, most powerful,
and most versatile GPS receiver we carry, the
Venus. The module can be configured to an amazingly powerful 10Hz update rate, with 14 channel
tracking! With two serial ports, UART and SPI
interfaces (please see the datasheets on how to
implement the SPI interface), 28mA operating
current, and high sensitivity, this receiver seriously
opens new doors for tracking. Module outputs the standard NMEA-0183
or SkyTraq Binary sentences at a default rate of 4800bps (adjustable to
115200bps).
The Venus634LPx has improved sensitivity, an integrated LNA (with
multipath detection and suppression), built-in RTC, and integrated single power supply making it very simple to use. In addition, the module
supports data logging with an external SPI Flash!
You can easily connect to the UART using our USB to Serial FT232
Breakout Board.
Check out our GPS buying guide!
The Logomatic Version 2 incorporates
the LPC2148 controller with USB, battery charging, and microSD support.
This allows us to use the SparkFun
LPC2148 USB bootloader for even easier and faster modification of the firmware. No programmer required!
The Logomatic v2 uses a USB mass
storage stack to appear under any operating system as a flash drive. Logs are
created in FAT16 format on the microSD media and can be downloaded quickly over a USB connection by
dragging and dropping the text files from the device.
The microSD card can also be removed and inserted into a card reader
to download the logs.
Board comes with a JST connector to be powered from our line-up of
LiPo batteries or other power sources up to 7.5VDC. If you choose to
use LiPo batteries, the Logomatic v2 has a built-in charger to charge
batteries off USB.
The Logomatic v2 ships with basic serial text and analog logging. Users
can easily start with this firmware but are encouraged to modify the
firmware for their specific requirements.
Price Each
GPS-101 Logomatic V2 Serial Datalogger
1
$93.25
5+
less 10%
Features:
1GB and 2GB MicroSD card and Adapter
* 51 channel acquisition and 14 channel tracking
* SkyTraq based chipset
* 10Hz max update rate (1Hz default)
* Integrated LNA
* Single 2.7-3.3V supply
* 3.3V TTL UART
* Power: 28mA tracking
* Sensitivity: -161dBm
* Accuracy: <2.5m
* Hot start: 1 Seconds
* Cold Start: 29 Seconds
* Supports active or passive antennas
* Supports SBAS (WAAS, EGNOS, MSAS)
Price Each
GPS-002 Venus GPS with SMA Connector
1
$69.95
We have 1 and 2 gig microSD media cards which
are perfect for massive datalogging in a minute
amount of space. These microSD cards have a
simple to use SPI interface allowing any micro to
read and write data in a very large 1 gigabyte
storage array.
Card may come with different brandings but does
include the small microSD card and a SD card converter.
Insert the microSD into the SD converter and then stick the larger SD
card into any standard card reader.
This product is guaranteed to work in any of our SD sockets, MMC
sockets, microSD sockets, or products that use a SD or MMC card.
Great for the Logomatic V2
5+
less 10%
Price Each
MSD-001 1GB microSD Card and Adapter
MSD-002 2GB microSD Card and Adapter
1
$19.95
$17.00
5+
less 10%
less 10%
uLog - The Lil'est Logger
Antenna GPS 3V Magnetic Mount SMA
Description: Magnet mount antenna for GPS modules operating at 3V. Designed for used with automobiles - the magnet will hold the antenna in
place at speeds greater than 100mph. 5meter
cable terminated with standard male SMA connector.
Check out our GPS buying guide!
Features:
* Gain 26dB
* VSWR <2.0
* Voltage 3.3V +/- 0.5V
* Current 12mA
* Weight 50g
Price Each
1
GPS-020 Antenna GPS 3V Magnetic Mount SMA $19.95
Price Each
LOG-020 Ulog – The Lil'est Logger
Page 25 Ocean Controls Catalog 2009
5+
less 10%
Description: The uLog is a tiny analog logging
device. Central to the logger is an ATtiny24
mated with an AT45DB161D 16Mbit flash IC.
Sampling at 50Hz, it’ll log 3 channels of 10-bit
ADC for about 2 hours before the memory fills
up.
Very stripped down and simple to use: at
power up it determines if a UART line is attached. If there is, it spits out a “?” and waits
for user input. There are only 2 commands: “r” for read and “e” for
erase. Erasing the flash sets all addresses to 0xFFFF, and reading
dumps all the data up to the first 0xFFFF. If there’s no UART line attached it starts sampling. If connecting with one of our FT232 breakout
boards, all you need is TX, RX and ground. If using an RS232 shifter
board you will also need to connect 3.3V.
The power input is a 2-pin JST connector, which works well with our
LiPo batteries, especially the small 100mAh LiPo, and it draws just 4mA
with an ADXL320 attached. An ON/OFF switch is also included.
There are so many uses for this device! We strapped it to a rocket while
it logged the analog output of an ADXL321 accelerometer.
Features:
* AT45DB161D provides 16 Mbits of flash
* Up to 3-channel ADC logging
* Access to ATtiny24 SPI pins
* Simple-to-use UART (38400 baud) interface for reading and erasing
flash
1
5+
Dimensions:* Size: 0.9x0.7"; * Weight: 8.07g
$23.93 less 10%
OCEAN CONTROLS - RELAY CONTROLLERS
USB I/O Controller
GOIC Modbus I/O Controller
The KT-5220 is a USB Controlled I/O module for interfacing PC's to
real world applications such as controlling
lights, pumps and sprinkler systems, reading sensors and monitoring switches and
other digital signals. The list is endless.
The GOIC Modbus I/O Card acts as
a Modbus RTU slave. It features
- Modbus Slave Address can be set.
- Baudrate and parity selectable
- Two 10bit analog inputs can be 420mA, 0-20mA or 0-5V inputs.
- Optional 12 bit Analog output. 420mA or 0-5VDC output
- Six digital inputs can sense NPN,
relay contacts or 0-5V TTL signals
- Two relay outputs with Normally open and closed contacts. Relays can
switch 3A @240VAC.
- Two of the digital inputs can be used to communicate with DS18s20
temperature sensors to monitor temperature over the range -55 to 125
degC
- Two of the digital counters also function as pulse counters
- 12 to 15VDC powered.
Communication via RS232 or RS485.
DIN Rail Mount Option
All external connections are via screw terminals
The controller provides eight relay outputs
each capable of switching 5 amps
@240VAC and four opto-isolated digital
inputs. Other features of the controller are
8 Relay Outputs
4 Opto Isolated inputs
2 Analog Inputs (0-5V or 0-20mA)
1 PWM Output
All connections to the I/O are via screw connectors.
A DLL and an example VB programs are provided
Power Indicator LE
Requires 12VDC plug pack and D25 Male-Female Cable
Price Each
KTA-220 USB I/O Controller
1
$135.00
5+
less 10%
Price Each
1
KTA-211 Modbus Card with 4-20mA Analog Output $124.50
Serial I/O Controller
Multi Drop Serial I/O Controller
The multi drop controller provides eight
relay outputs each capable of switching
5 amps @240VAC and four optoisolated digital inputs. All connections to
the I/O are via screw connectors.
It has been programmed so that each
controller has its own programmable
address. Up to 10 controllers can be
multi dropped on a RS232 serial line or
RS485 serial line.
It also has been programmed so that
the 4 digital inputs can be used as 24 bit counters
Requires 12VDC plug pack and D9 Male-Female Cable
A multi drop kit is available to convert the standard serial I/O controller
into a Multi Drop Serial I/O controller
The controller provides eight relay outputs each capable of switching 5 amps
@240VAC and four opto-isolated digital
inputs. All connections to the I/O are via
screw connectors.
It is controlled via a computers RS232
serial port via ASCII commands. Serial
cables can be much longer (up to 35
metres) allowing 'remote' control. Use
our RS232/RS485 convertors and distance of over a 1000 metres can be
obtained.
Requires 12VDC plug pack and D9 Male-Female Cable
Price Each
KIT-108 As Kit
KTA-108 Assembled and Tested
5+
less 10%
1
$99.00
$115.00
5+
less 10%
less 10%
Price Each
KTU-108 Upgrade Kit
KTM-108 Multi Drop Controller Assembled
1
$29.95
$135.00
5+
less 10%
less 10%
Pixel Programmable Controller Board
This controller is based around the PICAXE 28X1 microcontroller. The
PICAXE controllers have been featured in Silicon Chip magazine.
The controller features 4 Ten bit Analog Inputs (0-5V), 8 digital inputs
and 8 relay outputs. Each of the digital inputs has pull up resistors to
allow easy interfacing to relay contacts, switches and 0 to 5V inputs
etc. Each relay output has a LED to indicate its state and is capable of
switching 5 amps @240VAC.
All connections to the I/O are via screw connectors. The Pixel Controller measures 122x111x25mm.
The software provides a complete programming environment for generating BASIC programs for the PICAXE. Programs can be edited,
compiled and downloaded.
The Pixel Controller is fitted with a Picaxe 28X microcontroller. Extra
features include - 4 Ten bit analog inputs (0-5V)
- Program memory approx. 1000 lines with intelligent download
- Data memory 260 bytes
Requires 12VDC power and D9 Male-Female Cable
Page 26 Ocean Controls Catalog 2009
Price Each
PIX-002 Pixel Controller Board
PIX-003 Pixel Controller Board In Din Rail
1
5+
$129.50 less 10%
$159.50 less 10%
OCEAN CONTROLS - RELAY CONTROLLERS & ARDUINO
CONTROLLERS
PC Parallel Port Relay Controller
SOM96 Relay Card
The SOM96 Serial Output Module is
designed to be used with PCs. Each
module has 4 independent single pole
changeover relays which can be independently addressed from the PC. The
standard RS232 serial output is converted to RS485 by the first module and
this is used to drive subsequent modules. Each module may be allocated one of 256 addresses, thus allowing for control of 1024 relays.
Addresses are selected using an 8 way DIL switch and more than one
module can have the same address.
This will allow several relays to be controlled simultaneously. Modules
can be physically placed in positions remote from the PC. The link from
the PC Serial Port to the first module is restricted to approximately 50
metres. After that modules can be located as much as 200 metres apart.
This PC Parallel Port Relay
board allows you to convert
your into a dedicated controller.
Simply connect a printer
cable from your computer
to the D25 connector on
the relay board. There are 8 relays each capable of switching 12VDC/120VAC @
10A and 240VAC @ 5A. All connections to the relay contacts are via screw terminals
Each relay has an LED to indicate when it is operated.
Requires 12VDC plug pack and D25 Male-Female Cable
Price Each
KIT-074 As Kit
KTA-074 Assembled and Tested
1
$57.00
$69.95
5+
less 10%
less 10%
PC Parallel Port Relay Card In Box
Price Each
NET-030 SOM-96 Relay Card
1
$49.00
Level Monitor
The KTA-251 is a level meter and relay controller card. It can easily
interfaced with sensors having a 0-5V / 0-20mA / 4-20mA outputs. Two
relays can be programmed to activate when an input crosses a level
(with optional hysteresis) or is within or outside a range.
The unit is equipped with a small LCD and buttons, allowing an easy-toconfigure interface. By using the pushbuttons and screen you are able
to select ranges and set relay ON-OFF levels. Configuration is stored to
non-volatile memory. The meter can also be easily interface to the
DS18S20 temperature sensors and Maxbotix MaxSonar-LV-EZ0 and
EZ1 ultrasonic range finders.
The unit can be mounted on a panel using screws and supports. A DIN
Rail mount can also be purchased.
SPECIFICATIONS
*Power Supply Vs and COM:
- KTA-251 / KTC-251:
9-16V DC (12V Nominal) ~200mA + External 5V
drain
- KTB-251 / KTD-251:
18-32V DC (24V Nominal) ~200mA + External 5V
drain
*Voltage Input Vin: 0-5V
*Current Input Iin: 0-20mA
*Digital Input Din: 0-5V, Compatible with Maxim DS18S20 temperature
sensors, which have an operating range of -55°C to 125°C and are
accurate to ±0.5°C over the range -10°C to 85°C.
*Relay Outputs R1 and R2: Single-pole, single-throw relays rated to 5A
(resistive). 240VAC / 30VDC
5V Auxiliary Supply 5V: 200mA
*Dimensions: 76L x 72W x 24H mm
APPLICATIONS
1. A user may wish to monitor the pressure in a vessel and sound an
alarm if the pressure drops too low or rises too high. The sensor is a 420mA, 0-100Bar pressure sensor.
2. A test oven needs to be maintained at 80degC. Using a DS1820 temperature sensor connected to the KTA-251 and a heater to the relay, the
controller can be programmed to switch on the relay at 79degC and
switch off at 81degC.
3. An interactive display must be switched on when a person comes
within a meter of the display. Using a Maxbotix MaxSonar-LV-EZ0 ultrasonic sensor connected to the KTA-251 it can programmed to switch the
relay ON (turns on display) when the sensor detects an object within 1
meter.
Price Each
1
KTA-251 Level Monitor 12VDC Powered
$89.00
KTB-251 Level Monitor 24VDC Powered
$89.00
KTC-251 Level Monitor 12VDC Powered DIN Rail Mount $109.00
KTD-251 Level Monitor 24VDC Powered DIN Rail Mount $109.00
Page 27 Ocean Controls Catalog 2009
Essentially exactly the same as our PC Parallel Port Relay Board but supplied fully assembled in a high quality plastic case. The software provided for the board works with this
unit
All components provided including a plastic
case with pre-punched and silk screened
front and rear panels to give the product a professional and attractive
finish as shown in the photos. Finished Dimensions (mm):
140Wx110Dx35H.
Requires 12VDC plug pack and D25 Male-Female Cable
Price Each
KTA-165 Assembled in Box
1
$89.00
5+
less 10%
ARDUINO Card
Description: Arduino is an open-source physical computing platform
based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop
stand-alone interactive objects or can be connected to software on your
computer (e.g. Flash, Processing, MaxMSP). The open -source IDE can
be downloaded for free (currently for Mac OS X, Windows, and Linux).
We now ship the new Arduino Duemilanove. The Duemilanove automatically selects the appropriate power supply (USB or external power). A
great description of the new functionality can be found here (USB fuse
protection, software reset, and much more!). Board comes fully assembled and tested with ATMega168 pre-loaded with bootloader. Please see
the Arduino support forum for more information about this new board
revision and bootloader.
Summary
Microcontroller ATmega328
Input Voltage (recommended) 7-12 V
Input Voltage (limits) 6-20 V
DC Current per I/O Pin 40 mA
Flash Memory 32 KB (of which 2 KB used by
bootloader)
SRAM 1 KB
EEPROM 512 bytes
Clock Speed 16 MHz
Price Each
ARD-001 Arduino Card
1
$54.95
5+
less 10%
Description: This is a motor shield for Arduino that will control two DC motors.
Based on the L298 H-bridge, the Ardumoto can drive up to 2
amps per channel. The board takes its power from the same
Ardumoto
- Motor
Shield
Vin line as the Arduino
board, includes
blueDriver
and yellow
LEDs to indicate active direction, and all driver lines are
diode protected from back EMF.
Control for motor attached to OUT1/2 is connected to digital
line 12 (direction A) and digital line 10 (PWM A).
Control for motor attached to OUT3/4 is connected to digital
line 13 (direction B) and digital line 11 (PWM B).
Compatible screw terminals and connectors are listed below.
Price Each
ARD-030 Ardumoto - Motor Driver Shield
1
$34.95
5+
less 10%
OCEAN CONTROLS - ARDUINO CONTROLLERS
Arduino Pro 328 - 5V/16MHz
Arduino Pro Mini - 3.3V/8MHz
It's blue! It's thin (0.8mm)! It's the Arduino Pro Mini! SparkFun's minimal design
approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader (select
'LilyPad' within the Arduino software). The Pro Mini is very much like the Wee, but
we added a handful of features to become a fully certified Arduino board.
Description: It's blue! It's skinny! It's the Arduino Pro!
SparkFun's minimal design approach to Arduino. This is a
5V Arduino running the 16MHz bootloader (select
'Arduino Duemilanove w/ 328' within the Arduino software). The power switch was moved to the side of the
board (good idea Limor!) to allow control when a shield is
attached.
Arduino Pro Mini does not come with connectors populated so that you can solder
in any connector or wire with any orientation you need. We recommend first time
Arduino users start with the Diecimila. It's a great board that will get you up and
running quickly. The Arduino Pro series is meant for users that understand the
limitations of system voltage (3.3V), lack of connectors, and USB off board.
Please note: The right-angle power switch is fragile.
We're working on making the switch stronger. For now,
please be gentle.
Arduino Pro does not come with connectors populated so that you can solder in
any connector or wire with any orientation you need. We recommend first time
Arduino users start with the Duemilanove. It's a great board that will get you up
and running quickly. The Arduino Pro series is meant for advanced users that
understand the limitations of system voltage (5V), lack of connectors, and USB off
board.
We wanted Arduino Pro to be low profile. The DC power jack footprint is available,
but not populated. We recommend running the board with a LiPo battery for better
portability.
We really wanted to minimize the cost of an Arduino. The Arduino Pro is like the
Arduino Duemilanove (same pin out) but to keep the cost low, we used all SMD
components, made it two layer, etc. This board connects directly to the FTDI Basic
Breakout board and supports auto-reset. The Arduino Pro also works with the
FTDI cable but the FTDI cable does not bring out the DTR pin so the auto-reset
feature will not work.
Features:
* ATmega328 running at 16MHz external resonator. Select 'Arduino Duemilanove w/ 328' to get the delay functions to work correctly.
* USB connection off board
* 5V regulator
* Max 150mA output
* Over current protected
* Reverse polarity protected
* DC input 5V up to 12V
* Resettable fuse prevents damage to board in case of short
* Power select switch acts as on/off switch
Price Each
ARD-040 Arduino Pro 328 - 5V/16MHz
1
$27.50
5+
less 10%
We really wanted to minimize the cost of an Arduino. The Arduino Pro Mini is like
the Arduino Mini (same pin out) but to keep the cost low, we used all SMD components, made it two layer, etc. This board connects directly to the FTDI Basic Breakout board and supports auto-reset. The Arduino Pro Mini also works with the FTDI
cable but the FTDI cable does not bring out the DTR pin so the auto-reset feature
will not work.
Features:
- ATmega168V running at 8MHz with external resonator (0.5% tolerance)
- Low-voltage board needs no interfacing circuitry to popular 3.3V devices and
modules (GPS, accelerometers, sensors, etc)
- USB connection off board
- Supports auto-reset
- 3.3V regulator
- Reverse polarity protected
- DC input 3.3V up to 12V
- On board Power and Status LEDs
Dimensions:
0.7x1.3" (18x33mm)
Less than 2 grams
Price Each
ARD-008 Arduino Pro Mini - 3.3V/8MHz
1
5+
ARDUINO Ethernet Shield
Description: The Arduino Ethernet Shield allows an
Arduino board to connect to the internet. It is based on
the Wiznet W5100 ethernet chip providing a network
(IP) stack capable of both TCP and UDP. The Arduino
Ethernet Shield supports up to four simultaneous
socket connections. Use the Ethernet library to write
sketches which connect to the internet using the
shield.
Making Things Talk
Description: Tom Igoe is one of the prolific
actors on the Arduino scene. One of the core of 5
Arduino developers, Tom has amassed a huge volume of
knowledge working with a multitude of technologies and a large
number of students over the past decade. Making Things Talk
is a small section of what he has learned. This book (in color!)
covers a wide range: flex sensors, Bluetooth wireless, XBee wireless, USB, networks, IR remote control, RFID, force sensitive resistors, protocols, and of course,
lots of LEDs. It's pretty awesome - and it's not just how to work with these neat
technologies, but how to apply them in innovative projects. This is a great book to
build upon a basic knowledge of Arduino. Tom does a great way of describing and
teaching on a very easy to understand level, while getting complex concepts
Price Each
BOK-001 Making Things Talk
1
$38.00
5+
less 10%
The shield provides a standard RJ45 ethernet jack.
The reset button on the shield resets both the W5100 and the Arduino
board. boards.
Price Each
ARD-020 Arduino Ethernet Shield
Page 28 Ocean Controls Catalog 2009
5+
less 10%
Arduino uses digital pin1 (TX) to communicate with the TellyMate. Just plug it into
your Arduino and use Serial.println() commands to output text onto your TV!
5+
less 10%
The shield provides a 3.5mm jack and the necessary
cable to convert to a composite video connection. The
baud rate is selected by jumpers, which are also included.
Features:
Price Each
ARD-050 TellyMate
1
$85.00
Description: The TellyMate Shield equips an Arduino with the
ability to send simple text and graphics to a TV. The TellyMate
Shield connects to an Arduino board using long headers which extend
through the shield. This keeps the pin layout intact and allows another shield to be
stacked on top.
Description: If you've heard about
this Arduino thing, but are unsure about
where to begin, Getting Started with Arduino is a
great place to begin. 110 pages of easy to read, well
written, Make/O'Reilly goodness. Massimo Banzi (author
and one of the 5 Arduino developers) describes the basic
hardware, writes some simple programs, and explains
how to use the free Arduino development environment.
1
$23.33
Arduino uses digital pins 10, 11, 12, and 13 (SPI) to communicate with the W5100
on the ethernet shield. While using the Ethernet Shield, these pins cannot be used
for general i/o.
TellyMate
Getting Started with Arduino
Price Each
BOK-002 Getting Started with Arduino
The ethernet shield connects to an Arduino board using long wire-wrap headers
which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.
1
$37.27
* TV output from your Arduino
* PAL or NTSC Composite Video
5+
* Stackable Shield
* works with Serial.println() etc.
less 10%
OCEAN CONTROLS - ARDUINO CONTROLLERS
Arduino ProtoShield Kit
Breadboard Mini Self-Adhesive Red
Description: This is a very small
breadboard with 170 tie points. This
bread board is compatible with the Arduino
Proto Shield shown above. Strong, self-adhesive
backing. Measures 1.8"x1.4"
Description: Riding on the waves
of the very popular Arduino USB board is
this small prototyping shield. Originally spawned
with collaboration between the folks at SFE and ITP
@ NYU, the Protoshield mates with the Arduino USB
board and gives the user a small soldering area, two
general LEDs, access to a BlueSMiRF socket, a
general pushbutton switch, and most important of all the Arduino reset switch is brought to the top level.
This comes in kit form and must be soldered together
by the end user. Please note - we do not ship assembly instructions! There are a few tutorials on assembly listed below. All soldering is
through-hole (relatively easy) but always check your component orientation before
soldering!
Price Each
ARD-070 Breadboard Mini Self-Adhesive Red
1
$5.27
5+
less 10%
Arduino Mega
The kit is pictured with the bread-board option. We highly recommend this breadboard! The bread board can be purchased separately as a related item shown
below.
Kit Includes:
* 1 - Protoshield bare PCB
* 1 - 40pin break-away male header
* 3 - 6-pin female connector
* 2 - 8-pin female connector
* 1 - 4-pin female connector
* 2 - Bright 5mm LEDs
* 2 - 330 Ohm resistors
* 2 - Momentary push buttons
* 1 - 10k resistor
* 2 - 0.1uF Capacitors
Features:
* All Arduino pins are brought to the top level
* 5V, GND, and Raw pins are exposed as well
* BlueSMiRF socket for wireless communication between Arduinos
* 2 general use LEDs
* 1 general use button
* Reset Button brought to top level
Price Each
ARD-060 Arduino ProtoShield Kit
1
$22.60
5+
less 10%
Description: Arduino is an opensource physical computing platform
based on a simple i/o board and a development environment that implements the Processing/
Wiring language. Arduino can be used to develop
stand-alone interactive objects or can be connected
to software on your computer (e.g. Flash, Processing,
MaxMSP). The open-source IDE can be downloaded
for free (currently for Mac OS X, Windows, and
Linux).
The Arduino Mega is a microcontroller board based
on the ATmega1280. It has 54 digital input/output pins (of which 14 can be used as
PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz
crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset
button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or
battery to get started. The Mega is compatible with most shields designed for the
Arduino Duemilanove or Diecimila.
Price Each
ARD-080 Arduino Mega
1
$77.89
5+
less 10%
Arduino MegaShield Kit
Description: The Arduino Mega now
has its very own prototyping shield! The
MegaShield mates with the Arduino Mega board and
gives the user a prototyping area, two general LEDs,
and, most important of all, the Arduino Mega reset
switch is brought to the top level. The shield also
works with our small breadboards if you don't want to
solder to the prototyping area.
This comes in kit form and must be soldered together
by the end user. Please note - we do not ship assembly instructions! All soldering is through-hole
(relatively easy) but always check your component orientation before soldering!
Kit Includes:
* 1 - MegaShield PCB
* 1 - 6-pin stackable female connector
* 11 - 8-pin stackable female connector
* 1 - Bright 5mm Green LED
* 1 - Bright 5mm Red LED
* 2 - 330 Ohm resistors
* 1 - Momentary push button
* 1 - 10k resistor
Features:
* All Arduino Mega pins are brought to the top level
* 5V and GND power busses
* Power and stat (connected to D13) LEDs
* Reset Button brought to top level
Price Each
ARD-081 Arduino MegaShield Kit
Page 29 Ocean Controls Catalog 2009
1
$21.53
5+
less 10%
OCEAN CONTROLS - SECURITY
Weatherproof Door / Alarm Control Keypad
RFID Weatherproof Door / Alarm Control Keypad
This door access controller keypad is designed for door strike and other
access control applications in home or business security installations. It
features 3 outputs; 5A NC/NO for door strike and 2 x 1A outputs for
alarm triggering or auxiliary security functions. It can be installed so that
each user can enter their own 4 digit pin number (up to 9999 users) or
alternatively user groups can be assigned allowing up to
100 million possible entry codes.
Features:
• Tamper switch
• 5A 30VDC output for doorstrike
• 2 x 1A 30VDC outputs for alarm triggering
• Single or multi user 4 digit entry codes
• Panic/duress output
• Operation voltage 12VAC/DC
• Dimensions 129H x 84W x 41Dmm
Price Each
SEC-001 Weatherproof Door / Alarm Control Keypad
1
$57.23
5+
less 10%
Description: This door access controller keypad is designed for door
strike and other access control applications in home or business security
installations. The use of RFID tags allows easy
movement for authorised users in and out of the building or secure area.
It allows 3 methods of entry, by use of keypad only, proximity card only
or keypad PLUS proximity card combined. The three inbuilt relays allow
control of a door strike at the entry point in addition to 2 independent
relays for security system triggering and duress alarm.
Weather Proof 100db Siren / Strobe
Description: Combined siren and strobe in a single
weather resistant housing. Separate input for siren and
strobe.
Black wire - common
White wire - siren
Blue wire - strobe
Features:
• 12-15VDC operation
• 125KHz frequency.
• Maximum read range 14cm
• Dimensions: 123 x 107 x 21mm
• Entry modes: keypad, proximity card, keypad PLUS
proximity card
• 3 relay outputs (door strike, alarm and duress)
• Entry delay
Page 30 Ocean Controls Catalog 2009
Features
• Weatherproof design & construction
• Tamper switch
• 2 x 3A relays for doorstrike
• 500 users
• Keypad lock after multiple false entries
• 1A relay for doorbell
• Single or multi user 4 digit entry codes
• Door forced/left open alarm output
• 12V DC operation
• Dimensions 129H x 84W x 41Dmm
Price Each
1
5+
SEC-002 RFID Weatherproof Door / Alarm Control Keypad $82.59 less 10%
RFID Keypad Access Controller
Price Each
SEC-003 RFID Keypad Access Controller
This RFID door access controller is designed for controlling a door strike
in home or business security installations. Each user can be assigned
an RFID key card which is used to activate the door locking mechanism.
For additional security it may also be configured to require a 4 digit
code to be entered on the keypad. Up to 500 users can be added to a
system It features 2 x 3A NC/NO relay contacts for door strike connection, plus alarm triggering. An auxiliary 1A relay output is provided for
doorbells. Operates with fail-safe or failsecure door strikes.
Specifications:
Supply Voltage: 10- 14V DC
SPL Output: 100dB @ 50cm
Current: 280mA
Flash Rate: 75 per minute
Dimensions (mm): 75W x 120H
1
$117.27
5+
less 10%
Price Each
SEC-004 Weather Proof 100db Siren / Strobe
1
$29.23
5+
less 10%
OCEAN CONTROLS - REMOTE CONTROLLERS
1 Channel UHF Relay Controller Module
2 Channel UHF Relay Controller Module
Features 2 Relays rated to 2A at 24V DC and
an NPN Transistor Output.
Each Relay can be set to operate in 2 second momentary mode or ON-OFF latching
mode.
Pushing both buttons together operates the
Transistor Output.
Alternatively the Module can be put into
'Gate Opening' or 'Garage Door' mode. In this
mode each relay operates for 2 minutes when
the corresponding button is pushed. Pushing
any button on the remote while either of the
relays are on when in this mode will switch
the relays off.
Operates on 12-24V DC or 15V AC.
30m Outdoor Range.
Supplied with one remote and is housed in an attractive case with a
Microswitch Tamper Output for Alarm Systems if the cover is removed.
Dimensions 73 x 100 x 25mm, Antenna Protrudes 86mm.
This mains powered unit can switch 240V
AC at 6 Amps via its inbuilt relay. Up to 10
remotes can be taught to control the unit.
The receiver can operate in 4 modes, On/
Off, Latched, Momentary and 2 minute
Timed operation. On/Off: The contacts are
switched alternately. Latched: The contacts
are switched. Momentary: The button must
be held down for 1 seconds to operate the
relay for 1 second. 2 Minute Timed Output:
The button must be held down for 2 seconds to operate the relay for 2 minutes.
Price Each
1
UHF-001 2 Channel UHF Relay Controller 24VDC $141.77
UHF-003 Spare Key Remote
$54.50
Price Each
1
UHF-002 1 Channel UHF Relay Controller 240VAC $141.09
UHF-003 Spare Key Remote
$54.50
5+
less 10%
less 10%
These are an Additonal Mains Outlet for the UHF010 Remote control as shown above
Allows remote control of just about any appliance in the
home! This 8 channel mains switching
package is suitable for switching up to
1000W. This makes it perfect for automating devices around the home at the
touch of a button. Extra mains switches
are available allowing up to 8 mains
outlets to be controlled remotely. The
RF signal used means you don't even
need to be in line-of-sight to the outlet
unlike some infra-red models available
on the market. Please check power
consumption of your appliances before
making your purchase
1
$27.23
Maximum switching power: 1000W
Transmission frequency: 433.92MHz
Operating range: 20m
Price Each
UHF-011 1 Additional UHF Mains Outlet
Page 31 Ocean Controls Catalog 2009
1
$69.95
$89.95
$28.00
5+
less 10%
Rolling Code 4 Channel UHF Relay Board
12VDC plug pack required
Price Each
KIT-157 As Kit with transmitter
KTA-157 Assembled and Tested
KTT-157 Additional Transmitter
1
$20.86
5+
less 10%
Rolling Code 2 Channel Relay Board
A 'state of the art' UHF remote control
almost impossible to 'crack'. Uses a pre
-built 'keyfob' style transmitter (as used
in many car lock systems) with 2
pushbuttons, one for each relay on the
matching receiver board. Each relay
can be either latching or momentary in
operation. An LED for each relay indicates when it is operated. The receiver
board uses a pre-built UHF receiver
module to decode the transmitter signal.
Up to 15 transmitter units can be learnt
by one receiver unit.
5+
less 10%
less 10%
Additional UHF Mains Outlets
Remote Controlled Mains Outlets
Price Each
UHF-010 1 UHF Remote Control Mains Outlet
Operates on 240VAC
30m Outdoor Range.
Supplied with one remote
Dimensions 73 x 100 x 25mm, Antenna Protrudes 86mm.
5+
less 10%
less 10%
less 10%
A 'state of the art' UHF remote control almost impossible to 'crack'.
Uses a pre-built 'keyfob' style transmitter (as used in many car lock
systems) with 4 pushbuttons, one for
each relay on the matching receiver
board. Each relay can be either
latching or momentary in operation.
An LED for each relay indicates
when it is operated. The receiver
board uses a pre-built UHF receiver
module to decode the transmitter
signal.
12VDC Plug Pack Required
Price Each
KIT-180 As Kit
KTA-180 Assembled and Tested
KTT-180 Additional Transmitter
1
$75.00
$95.00
$29.50
5+
less 10%
less 10%
less 10%
OCEAN CONTROLS - REMOTE CONTROLLERS
Tx and Rx Modules Used in KTA-157
Rolling Code 10 Channel UHF Relay Board
This kit uses the same Tx/RX pair as
4Channel Controller but it uses all 10 defined keypress combinations out of the 4
buttons to activate relays. Buttons 1, 2, 3,
and 4 (of course) and the buttons 1&2,
1&3, 1&4, 2&3, 2&4, and 3&4 pressed
together. A PIC16F628 does ALL the work
Toggle or momentary mode is determined
by keeping the one or two buttons depressed for more than 2 seconds and then
that relay will stay in that mode until another >2 sec keypress. Small relays are
used to save weight and board area.
12VDC plug pack required
Price Each
KIT-181 As Kit
KTA-181 Assembled and Tested
KTT-181 Additional Transmitter
These are the same 2 button transmitters
and receivers used in our rolling code 2
channel 434MHz UHF relay board
Battery is already fitted into the transmitter
Price Each
KTT-157 A17-Tx 2 Channel UHF Transmitter
KTR-157 A17-Rx 2 Channel UHF Receiver
5+
less 10%
less 10%
Tx and Rx Modules Used in KTA-180
1
$99.00
$129.00
$29.50
5+
less 10%
less 10%
less 10%
Infra Red 12 Channel Relay Board Controller
These are the same 4 button transmitters and 4 channel receivers used in our rolling code 4 channel
434MHz UHF relay board.
Battery is already fitted into the transmitter
Price Each
KTT-180 A16-Tx 4 Channel UHF Transmitter
KTR-180 A16-Rx 4 Channel UHF Receiver
This kit comprises a commercial 14button IR remote controller PLUS a
12 channel relay board. All 12 relays
are provided on the receiver board nothing more to add. Makes it very
simple to add infrared remote control
to any project or existing equipment.
Indicator LEDs show which relay is
operated. Operating range up to 18
metres/60 feet (length of the factory!).
12VDC Plug Pack Required
Price Each
KIT-142 As Kit
KTA-142 Assembled and Tested
RIR-101 12 Button Remote
1
$28.00
$25.00
1
$29.50
$24.50
5+
less 10%
less 10%
Infra Red Relay Controller Board
This kit allows you to turn on and off a variety of electrical devices using almost any household infrared remote control unit
(e.g. TV, video, satellite, hi-fi, etc). Relay output rated at 12VDC
5A or 240VAC 3A. If you wish to switch heavier loads use our
DIN mounted relays
1
$84.00
$114.00
$20.00
5+
less 10%
less 10%
less 10%
Push any button of the remote control and the PCB mounted
relay will turn on. Push any button a few seconds or hours later
and the relay will toggle off.
Supply: 8 - 15V DC required
PCB measures: 28x74mm.
Price Each
KIT-058 As Kit
KTA-058 Assembled and Tested
1
$21.95
$35.50
5+
less 10%
less 10%
UHF Sequence Logic Controller
Our UHF Sequence Logic Controller allows you to program the operation of 6 relays based on the
condition of the UHF transmitter buttons and digital inputs. You develop the program on your PC,
test it on the PC and then download it.
Some control examples are
- On pushing a single button you could automatically open a gate wait a few seconds and then
close it.
- Push button 'x' closes relay 'x' and switches off the other relays.
- Security system button 1 opens a gate and turns on the lights, button 2 just turns on the lights
for a defined length of time.
- In photography pushing button 1 turns on relay 1 to wind on film then relay 2 is turned on to take the photograph , waits a second then repeats the
process 60 more times.
The applications are endless
The logic controller features
Price Each
1
5+
- 4 button key FOB UHF 433MHz Transmitter
KTA-230 Wireless Sequence Logic Controller.
$159.00 less 10%
- 6 Relays with changeover contacts can switch 5 amps @240VAC
KTA-231 Wireless Sequence Logic Controller no transmitter $129.00 less 10%
- 4 Isolated Digital Inputs
KTT-180 A16-Tx 4 Channel UHF Transmitter
$29.50
less 10%
- 2 0-5V Digital Inputs
- screw terminal connections for all inputs and outputs
- 12VDC powered
The controller can handle up to 15 transmitters so if you can have a number of people with their own transmitters operating the controller. The transmitters use rolling code technology so it’s close-to-impossible to electronically “crack”
The 4 button transmitter will operate the controller from a distance of up to 50m clear line of site
Page 32 Ocean Controls Catalog 2009
OCEAN CONTROLS - REMOTE CONTROLLERS
Remote Telemetry Unit
The KTA-235, KTA-236 and KTA-237 are an ASCII based easy to use Remote Telemetry Unit or
RTU. It is designed to be used with a PC or PLC, where the PC or PLC can remotely control and
monitor the status of 6 Relays, 4 optically isolated inputs and 2 Analog inputs. The Analog inputs can
also be set to behave as dry contact or open collector digital inputs in cases where analog inputs are
not required. Each unit is individually addressable, which means that multiple controllers can
be used on the serial link, and the option of a serial modem means that units can be wirelessly controlled up to 1000m from the host.
The RTU comes in 3 forms
KTA-235 communicates via an RS232 serial connection. This connection can be multidropped using a
combination of diodes and resistors
KTA-236 using a UM96 (9600 baud) wireless modem card. A distance of 500m can be achieved via direct line of sight.
KTA-237 using a UM12 (1200 baud) wireless modem card. A distance of 1000m can be achieved via direct line of sight.
The wireless modems operate in the licence free 433MHz band.
Measures 135(L) x 140(W) x 35(H)mm
Price Each
1
KTA-235 Serial Remote Telemetry Unit
$129.00
KTA-236 Wireless Remote Telemetry Unit 9600Baud.$179.00
KTA-237 Wireless Remote Telemetry Unit 1200Baud.$179.00
5+
less 10%
less 10%
less 10%
Wireless Back To Back Controller
We have now reprogrammed our KTA-235 Remote Telemetry Unit or RTU to operate as a back to
back controller.
What is a Back to Back Controller?
The KTA-238 has 4 isolated digital inputs, 2 non isolated 0-5V digital inputs and 6 relay outputs. Two
KTA-238's are connected by a communications link. The link can be RS232, RS485 or wireless. The
status of the inputs for each controller are automatically transmitted to the other controller where they
are written to the relay outputs. In the diagram below you will see the switch S1 at Site 2 turns on
Motor 1 at Site 1
the switch S2 at Site 2 turns on Lamp 2 at Site 1
the switch S3 at Site 2 turns on Horn 3 at Site 1
the switch S5 at Site 1 turns on Lamp 5 at Site 2
As you can imagine the applications are endless
Turn on a pump from your house. Security if a perimeter contact is broken a
horn or lamp is activated at the central location. Alarm if a level in a tank gets
low or high an alarm is activated.
Price Each
KTA-238 Wireless Back to Back Controller.
KTA-239 Serial Back to Back Controller
1
$179.00
$129.00
5+
less 10%
less 10%
Each KTA-238 controller provides 6 changeover relay outputs each capable of switching 5 amps @240VAC and four opto-isolated digital inputs. All
connections to the I/O are via screw connectors.
Measures 135(L) x 140(W) x 35(H)mm.
OCEAN CONTROLS - TEMPERATURE CONTROLLERS
N322 Temperature Thermostats
The Novus N322 Thermostats can be used with NTC Thermistors, PT100 and J Type Thermocouples.
The NTC Thermistor model is provided with a NTC Thermistor and 2m long cable to get you up and running
immediately. The N322 Thermostats have two relay outputs which can be configured for heating or cooling
or a number of different alarm modes and are easily configured by the front panel buttons and display. The
Temperature and status of Relays are shown on the LED Display.
Great for Aquariums, Home Brewing and many other applications.
- Sensor input: Pt100 (-50 to 300°C), Pt1000 (-200 to 530ºC), Thermocouple J,K and T (0 to 600°C) or
thermistor (-50 to 120ºC).
- IP65 enclosure frontal protection
- Output: 2 relays SPST
- Resolution: 0,1°C from -19,9 to 99,9°C
- Accuracy: ± 0,5°C/°F ±1 digit (Pt100/Pt1000/Thermistor) and ±2°C for
Thermocouple.
Price Each
- Adjustable hysteresis
CET-001 N322 NTC Thermistor Electronic Thermostat
- Sampling: 1,5 per second
CET-002 N322 Pt100 Electronic Thermostat
- Working temperature: 0 to 50°C
CET-003 N322 Thermocouple Electronic Thermostat
- Power supply: 85-250Vac (internal) 12VDC optional
CET-004 N322 NTC Electronic Thermostat 12VDC
Page 33 Ocean Controls Catalog 2009
1
$89.00
$99.00
$99.00
$89.00
5+
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - TEMPERATURE CONTROLLERS
N322T Temperature Thermostats with Timer
Temperature controller for heating and refrigeration purposes with timer support. It has PT100 RTD, thermistor NTC or J thermocouples inputs available. Allows energy time delay and minimum on/off time settings
The NTC Thermistor model is provided with a NTC Thermistor and 2m long cable to get you up and running immediately.
The timer output is typically used for the system defrost. The t1 and t2 parameters define, respectively, the
interval and duration of the defrost cycles.
Sensor input: Thermistor (-50 to 120 ºC), Pt100 (-50 to 300 °C), Thermocouple J (0 to 600 °C).
IP65 enclosure frontal protection
Output: 10 A control relay and 3 A alarm relay
Resolution: 0,1 °C from -19,9 to 199,9 °C
Operating temperature: 0 to 40 °C
Price Each
Power supply: 100~240 Vac/dc (± 10 %) or 24 Vdc/ac (12~30 Vdc/ac)
CET-006 N322T NTC Timer 240VAC
RS-485 digital communication; RTU MODBUS protocol (optional)
CET-008 N322T NTC Timer with RS485 240VAC
Dimensions: 75 x 33 x 75 mm
1
$109.00
$114.00
5+
less 10%
less 10%
1
$109.00
5+
less 10%
N323R Temperature Thermostats
N323R Model: This model of temperature controller controls the end of defrosting by temperature. It features three output relays: compressor, defrosting and fan. It operates with two sensors (NTC), one for
room temperature and other to be attached to the evaporator for control of defrost end. Employed in cooling and defrosting.
Example: Frozen chambers and displays.
Sensor input: Thermistor (-50 to 120 ºC), Pt100 (-50 to 300 °C), Thermocouple J (0 to 600 °C).
IP65 enclosure frontal protection
OUTPUT1: Relay SPDT; 1 HP 250 Vac / 1/3 HP 125 Vac (10 A Resistive)
OUTPUT2: Relay: 3A / 250 Vac, SPST
OUTPUT3: Relay: 3A / 250 Vac, SPST Resolution: 0,1 °C from -19,9 to 199,9 °C
Operating temperature: 5 to 50 °C
Power supply: 100~240 Vac/dc (± 10 %) or 24 Vdc/ac (12~30 Vdc/ac)
RS-485 digital communication; RTU MODBUS protocol (optional)
Price Each
Dimensions: 75 x 33 x 75 mm
CET-030 N322R NTC Defrost 240VAC
N322 Relative Humidity and Temperature Controller
The N322RHT is a digital controller for relative humidity and temperature. Its 2 relay outputs can be configured independently as control or alarm, either for temperature or relative humidity. A Relative Humidity and Temperature or RHT probe (3 m length) is provided along with the instrument
Both the Temperature, Humidity and status of Relays are shown on the LED Display. Applications include fruit storage and air conditioning.
INPUT SENSOR:
Humidity measurement: Accuracy: Refer to Figure 01;
Stability: < 1 %RH / year;
Range: 0 and 100 % RH
Linearity error: << 1 % RH; Long term Stability: < 1 % RH
Response time: 4 seconds in the range from 10 to 90 %, with slow moving air. Outside this range, up to 48 hours.
Temperature measurement: Accuracy: Refer to Figure 1;
Repeatability: ±0.1 °C;
Range: -40 and 120 °C (-3.8 to 211.8 °F)
Response time: up to 30 seconds in slow moving air.
WARM-UP: 15 minutes
MEASUREMENT RESOLUTION:
Temperature: 0.1º for indications between –19.9º and 119,9º 1º elsewhere
RH: 1%
OUTPUT1:Relay SPDT; 1 HP 250 Vac / 1/3 HP 125 Vac (10 A Resistive)
OUTPUT2:Relay: 3A / 250 Vac, SPST
POWER SUPPLY: 100~240 Vac (± 10 %) or optional 24 Vdc/ac (12~30 Vdc/ac)
DIMENSIONS: Width x Height x Depth: 74 x 32 x 75 mm PANEL CUT-OUT: 70 x 29 mm WEIGHT: 100
g
ENVIRONMENT: Operating temperature: 0 to 40 °C (32 to 122 °F) Storage temperature: -20 to 60 °C (-4 to 140 °F) Relative humidity: 20 to 85 % non
condensing
CASE: Polycarbonate UL94 V-2; Protection: Front panel: IP65, Box: Price Each
1
5+
IP42
CET-007 N322RHT Temperature and RH Controller 240VAC
$195.00 less 10%
RS-485 digital communication; RTU MODBUS protocol (optional)
Page 34 Ocean Controls Catalog 2009
OCEAN CONTROLS - PROCESS CONTROLLERS
N440 Process Controller
The N440 is an ON/OFF action digital temperature controller which provides maximum versatility at an economic price and can be a great substitute for the obsolete analog controllers.
It accepts thermocouples type J, K or Pt100 RTD and features one relay and one voltage pulse output for
Solid State Relays.
Keypad programming is simple and intuitive and parameters setting can be selectively locked.
The N440 is aimed at simple temperature heating or cooling processes applications that require low cost and
yet demand good display accuracy with simple operation.
Features include
- Temperature ranges:
Thermocouple J: 0 to 600 ºC, 1 ºC resolution.
Thermocouple K: 0 to 1370 ºC, 1 ºC resolution.
Pt100: -50 to 530 ºC; 0.1 ºC resolution from -19.9 °C and 199.9 ºC
- Thermocouples according to NBR 12771/99, Pt100 NBR 13773/97.
- Pt100 three-wire connection with automatic cable resistance compensation.
- Pt100 excitation current: 170 uA.
- Internal cold junction compensation for thermocouples.
- Accuracy: Thermocouple: 3 ºC maximum error, Pt100: 1 ºC maximum error.
- A/D converter resolution: 13 bits. Sampling rate: 5 measurements per second.
- Display: 3½ digit LED with 13 mm height.
- Indication and control time response: < 2 s.
- Output 1: SPDT relay, 5 A / 250 Vac. Output 2: 5 Vdc / 20 mA pulse. Optional: 3 A / 250 Vac relay.
- Operating ambient: 0 to 50 ºC, 20 to 85 % Relative Humidity, non-condensing.
- Dimensions: 48 x 48 x 110 mm (1.89” x 1.89” x 4.33”). Panel cutout: 45.5 x 45.5 mm.
- Power: 100 to 240 Vac/dc.
Price Each
1
CET-010 N440-CPR In: RTD Out: 1 relay+pulse Pwr: 240VAC
$109.00
CET-015 N440-JPR In: J T/C Out: 1 relay+pulse Pwr: 240VAC
$114.00
CET-020 N440-KPR In: K T/C Out: 1 relay+pulse Pwr: 240VAC $109.00
5+
less 10%
less 10%
less 10%
N480 Process Controller
The N480D series of PID temperature controllers was designed for non-experienced novice users for combining extreme simplicity in operation with high performance only found in expensive high end controllers.
It is a low-cost instrument which can be easily installed and operated. It accepts J,K and S thermocouples
and Pt100 RTD, features a relay and pulse output for driving solid state relays and optionally can be supplied with a linear 4 to 20 mA output.
Autotuning PID function, dual display, full range universal power supply and ramps soak function are standard.
It greatly surpasses the old and obsolete analog controllers in performance with ease of operation.
Features include
- Accepts thermocouples type
J range -50 ºC to 760 ºC, K range -90 ºC to 1370 ºC, T range -100 ºC to 400 ºC
R range 0 to 1760 ºC, S from 0 to 1760 ºC, E range -30 a 720 ºC
N range -90 a 1300 ºC
- cold junction compensation.
- Accepts 2 or 3-wire Pt100 RTD, range -200 ºC to 530 ºC, with cable resistance compensation.
- Pt100 excitantion current: 0.170 uA.
- Internal A/D resolution: 15,000 levels
- Displayed resolution: 7,500 levels.
- Four-digit 10 mm red display for measured variable and four-digit 7 mm green display for setpoint.
- Sampling rate: 5 measurements per second.
- Control output update: 200 ms.
- 5 Vdc 20 mA logic control output.
- 1 SPDT relay and 2 SPST 3A @ 250 Vac relays.
- Power: 100 to 240 Vac/dc, 50/60 Hz; optional 24 Vdc/ac.
- Power consumption: less than 9 VA.
- Operating environment: 0 to 55 ºC, 20 to 95 % RH.
- Front panel: IP65, Polycarbonate UL94 V-2, Back panel: IP30, ABS+PC UL94 V-0.
- Weight: 140 g with 1 relay, 160 g with 3 relays.
- Dimensions: 48 x 48 x 110 mm (1.89” x 1.89” x 4.33”).
Price Each
CET-050 N480D T/C, RTD 2 Relays+Pulse Pwr: 240VAC
CET-051 N480D T/C, RTD 2 Relays+Pulse Pwr: 24VDC
CET-052 N480D T/C, RTD 3 Relays Pwr: 240VAC
CET-053 N480D T/C, RAR 2 Relays+Pulse Pwr: 240VAC
CET-054 N480D T/C, RAR 2 Relays+Pulse Pwr: 24VDC
Page 35 Ocean Controls Catalog 2009
1
$139.00
$139.00
$139.00
$152.50
$152.50
5+
less 10%
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - PROCESS CONTROLLERS
N1100 Process Controller
The N1100 series of Universal Process Controllers is a real breakthrough in versatility for holding in one
single instrument all the major features that are needed for the vast majority of industrial processes.
The sophisticated and consistent software and its advanced truly universal SMT circuitry make the N1100
the only 1/16 DIN PID instrument in the world to accept configuration of both input signal and control output
through the front keyboard without any hardware change.
From the very simple applications as a temperature controller to the most complex systems of distributed
control with PLC's or SCADA networks, the N1100 is the right answer to your needs for industrial, building
or laboratory automation
Features include
- Universal Input accepts: Thermocouples J, K, T, S, Pt100, 4-20mA, 50mV, 0-5Vdc
- Double LED display: red for PV and green for SV.
- Outputs: 3A/250Vac Relay, linear 4-20mA and logic pulse for solid state relays available.
- 2 alarms (Relays SPST) more Out linear 4-20mA or logic pulse (standard).
- Up to 2 time relays, 0 to 6500 seconds.
- Input resolution: 12,000 levels.
- PV or SP retransmission in 4 to 20mA.
- RS485 comm with Modbus RTU protocol (optional).
- Auto tuning PID control.
- Auto/Manual mode, bumpless transfer.
- Remote setpoint input (4 to 20mA).
- Programmable Soft start up to 9999 seconds.
- Ramp and Soak: 7 programs of up to 7 segments each. Can be linked to create longer programs of up to 49 segments.
- Power: 85 to 264 Vac, 50/60 Hz. Dimensions: 48 x 48 x 106 mm.
Price Each
PID-001 N1100 Process Controller
PID-002 N1100 Process Controller with RS485
PID-003 N1100 Process Controller 24V
PID-004 N1100 Process Controller 24V with RS485
1
$175.00
$199.00
$175.00
$199.00
5+
less 10%
less 10%
less 10%
less 10%
N2000 Process Controller
The N2000 Universal Process Controller is a real breakthrough in versatility for holding in one single instrument all the
major features required in the vast majority of industrial processes.
With a sophisticated and consistent software and its advanced truly universal circuitry, the N2000 accepts configuration
of both input signal and control output through the front keyboard without any internal hardware change.
Power supply for remote loop powered transmitters is standard and is a must for high-end applications.
From the very simple applications as a temperature controller to the most complex systems of distributed control with
PLC’s or SCADA networks, the N2000 is the right answer to your needs for industrial or laboratory automation.
The N2000S is specific for applications in controlling servo motorized valves, servo actuators and dampers by
means of two time proportional relays. :
Features include
- Universal Input accepts thermocouples type J, K, T, N, R, S; Pt100 RTD, linear 4-20 mA, 0-50 mV, 0-5 Vdc.
- Double LED display: red for PV and green for SV.
- Dual SPST 3A/250 Vac relays and dual SPDT 5A/250 Vac relays can be individually programmed for control or alarm.
- Isolated 4-20mA output with 1500-level resolution, maximum 550 ohm load for control or PV/SV retransmission. It can
also be configured for digital input or output (10 Vdc/20 mA).
- Sampling rate: 4 measurements per second.
- One digital input for dry contact with 5 programmable functions.
- Remote setpoint input for 4-20 mAdc signal (N2000).
- 24 Vdc/30 mA supply output for remote transmitter excitation.
- RS485 comm with Modbus RTU protocol.
- Auto tuning PID control.
- Auto/Manual mode, bumpless transfer.
- Programmable Soft start up to 9999 seconds.
- Ramp and Soak: 7 programs of up to 7 segments each. Can be linked to create longer programs of up to 49 segments.
- Measured value resolution: 12,000 levels.
- Control output update: 250 ms.
- Up to four configurable relays, two timer alarms.
- Alarm functions: LO, HI, differential, differential LO, differential HI, sensor break and event.
- Alarm initial blocking function.
- Power: 85 to 250 Vac, 50/60 Hz; optional 24 Vdc/ac.
- Dimensions: 48 x 96 x 92 mm.
Price Each
PID-010 N2000 Process Controller with RS485
PID-020 N2000S Servo Positioning Process Controller with RS485
Page 36 Ocean Controls Catalog 2009
1
$239.00
$259.00
5+
less 10%
less 10%
OCEAN CONTROLS - PROCESS CONTROLLERS
N1200 PID Controller
The N1200 is an advanced self-adaptive PID controller with an algorithm that constantly monitors the process
performance and adjusts PID settings in order to always obtain the best possible control response.
A single model is able to accept most industrial sensors and signals and provides all output types required to
control different processes.
All controller parameters can be accessed from the front panel without performing any hardware change.
The multi-purpose inputs and outputs can be combined to provide tremendous versatility with extremely high
accuracy in the most demanding applications.
A Modbus RTU RS485 is an optional extra. You can use the Superview software or ISEE-Modbus Software
to monitor and set parameters in the controller
Features include
- Accepts thermocouples J, K, N, R, T, S, B, E, Pt100 RTD, 0-20 mA, 4-20 mA, 50 mV, 0-5 Vdc and 0-10
Vdc.
- Internal resolution: 32,767 levels (15 bits).
- Displayed resolution: 12,000 levels.
- Dual LED display: red upper display for PV, 10 mm high; green lower display for SV, 8 mm high.
- Sampling: up to 55 measurements/second.
- Control output update: up to 20 ms.
- Isolated 4-20 mA output with up to 32,000 resolution levels (15 bits), 550 ohms maximum load.
- 2 SPST relays 1,5 A / 240 Vac/dc and 1 SPDT relay (optional)
- 3 A/250 Vac/dc.
- Power supply: 100 to 240 Vac/dc, 50/60 Hz; optional 24 Vac/dc.
- Maximum consumption: 9 VA.
Price Each
1
- Operating environment: 5 to 50 °C, 30 to 80% RH.
PID-040 N1200 24V Self Adaptive PID Controller
$259.00
- Protection: NEMA 4 front bezel (IP65), PC UL94 V-2
PID-041 N1200 Self Adaptive PID Controller
$259.00
case IP20, ABS + PC UL94 V-0.
PID-042 N1200 Self Adaptive PID Controller w/ 3 relays +RS485
- Rated CE and UL.
$329.00
- Dimensions: 48 x 48 x 110 mm.
PID-043 N1200 24V Self Adaptive PID Controller w/ 3 relays +RS485
- Panel cutout: 45.5 x 45.5 mm (1.79 x 1.79 in)
$333.00
- Approximate weight: 150 g
5+
less 10%
less 10%
less 10%
less 10%
N3000 Process Controller
The N3000 Big Digit Universal Process Controller is a real breakthrough in versatility for holding in one
single instrument all the major features required in the vast majority of industrial processes.
With a sophisticated and consistent software and its advanced truly universal circuitry, the N3000 accepts
configuration of both input signal and control output through the front keyboard without any internal hardware change.
Power supply for remote loop powered transmitters is standard and is a must for high-end applications.
From the very simple applications as a temperature controller to the most complex systems of distributed
control with PLC’s or SCADA networks, the N3000 is the right answer to your needs for industrial or laboratory automation. A Modbus RTU RS485 connection is fitted. You can use the Superview software or
ISEE-Modbus Software to monitor and set parameters in the controller
Features include
- Double LED display: red for PV (18 mm) and green for SV (13 mm).
- Accepts thermocouples type J, K, T, N, R, S; Pt100 RTD, linear 4-20 mA, 0-50 mV, 0-5 Vdc.
- Sampling rate: 4 measurements per second. - Measured value resolution: 12,000 levels.
- One digital input for dry contact with 5 programmable functions.
- Remote setpoint input for 4-20 mAdc signal.
- Dual SPST 3 A / 250 Vac relays and dual SPDT 5 A / 250 Vac relays can be individually programmed for control or alarm.
- Isolated 4-20 mA output with 1500-level resolution, maximum 550 ohm load for control or PV/SV retransmission. It can also be configured for digital
input or output (10 Vdc / 20 mA).
- Auto tuning PID control. Auto/Manual mode, bumpless transfer. - Programmable Soft start up to 9999 seconds.
- Ramp and Soak: 7 programs of up to 7 segments each. Can be linked to create longer programs of up to 49 segments.
- Control output update: 250 ms.
- Up to four configurable relays, two timer alarms.
- Alarm functions: LO, HI, differential, differential LO, differential HI, sensor break and event.
- Alarm initial blocking function.
- Power: 100 to 240 Vac, 50/60 Hz; optional 24 Vdc/ac.
- Maximum consumption: 3 VA.
- 24 Vdc / 30 mA supply output for remote transmitter excitation.
- RS485 comm with Modbus RTU protocol (optional).
Price Each
1
5+
- Front panel: IP65, Polycarbonate UL94 V-2.
PID-030 N3000 Process Controller 240VAC with RS485
$259.00
less 10%
- Back panel: IP30, ABS + PC UL94 V-0.
PID-031 N3000 Process Controller 24VDC with RS485
$259.00
less 10%
- Operating environment: 0 to 55 ºC, 20 to 85 % RH.
- Dimensions: 96 x 96 x 92 mm. Panel cutout: 93 x 93 mm Weight: 330 g.
Page 37 Ocean Controls Catalog 2009
OCEAN CONTROLS - PROCESS CONTROLLERS
KTA-389 4 Channel Temperature Monitor & Controller!
This kit is an 'extension' of the KTA145
Temperature Logger kit. Like the KTA145
it features four (4) temperature inputs
using the DS1820 digital sensor. In addition four (4) relays have been added to
provide output control. Supplied with plastic case and front/rear panels for a professional looking finish.
Commands for reading temperatures or
controlling relays are sent via the RS232
interface using simple text strings. The kit can be controlled using a simple
terminal or communications program (such as Hyperterminal) or via a
freeware Windows application (see below) Connected to a PC you will
be able to carry out ON/OFF temperature control.
Temperature range: -55 to +125 degrees C
Please note: The kit does not include any DS18S20 temperature sensors. They have to be purchased separately.
Typical applications include
Computer server monitoring
Home temperature monitoring
Home automation tasks (start fan if warmer outside during Summer)
Refrigerator monitoring and testing
Brewing temperature regulation
Fish tank heater verification
Price Each
KIT-389 Serial Temperature Monitor Kit
KTA-389 Serial Temperature Monitor Assembled
PTP-003 DS18S20 Temperature Transducer
CAB-002 D9 RS232 Male-Female Cable 1.8 metres
PLP-003 12VDC, 500mA Plug Pack
1
$95.00
$115.00
$12.00
$8.77
$14.55
5+
less 10%
less 10%
less 10%
less 10%
less 10%
Anemometer Interface Card
The KTA-250 is an anemometer monitoring and
alarming card. It allows the wind speed and
direction to be measured with a Davis Instruments DS7911 Anemometer, without the need
for the entire weather station. Monitoring of the
wind speed and direction can be done via the
analog retransmission channels with 0-5V, 15V, 0-20mA or 4-20mA outputs. As well as
monitoring the speed and direction, 2 alarm
relays can be programmed to activate at a certain speed or wind direction range, or combination of the two. Wind speed and direction can also
be monitored using the Modbus protocol with either an RS232 or 2-wire
RS485 connection. All settings are set using the Modbus protocol and
the provided software.
Features
*Connects to Davis Instruments DS7911 Anemometer
8Monitor both the wind speed and direction
*Interface to PLC's using the Modbus protocol
*Communicate via RS232 or 2-wire RS485
I*nterface to PLC's/Instruments or other controllers using 4-20mA or 0-5V signals
*Generate relay alarms depending on the wind
speed and direction
*Alarms can be monitored by the on board
relays or via the Modbus protocol
*DIN Rail mounting available
Price Each
KTA-250 Anemometer Interface Card
KTD-250 Anemometer Interface Card DIN Rail
ANM-001 Davis Instruments 7911 Anemometer
Price Each
ECS-001 Wireless Vantage Pro 2
ECS-002 Wireless Vantage Pro 2 Plug
ECS-003 WeatherLink for Vantage Pro Serial
Page 38 Ocean Controls Catalog 2009
1
5+
$159.00 less 10%
$179.00 less 10%
$215.00 less 10%
1
5+
$980.00 less 10%
$1560.00 less 10%
$260.00 less 10%
KTA-390 4 Channel Temperature Controller!
We have reprogrammed the microcontroller in the KTA-389 to become a
standalone 4 channel temperature ONOFF Controller. The controller can do
both heating and cooling. So you can
control the temperature in 4 fish tanks
or 4 heaters for brewing. Supplied with
plastic case and front/rear panels for a
professional looking finish.
Commands for reading temperatures,
controlling relays, setting ON-OFF temperatures are sent via the RS232
interface using simple text strings. A simple to use Windows program
allows you to easily program the controller. Once programmed you can
separate the controller from the PC and it will operate on its own. All
parameters are saved in EEPROM so they are not lost if power is removed from the controller
Please note: The kit does not include any DS18S20 temperature
sensors. They have to be purchased separately.
Price Each
KTA-390 Serial Temperature Controller Assembled
PTP-003 DS18S20 Temperature Transducer
CAB-002 D9 RS232 Male-Female Cable 1.8 metres
PLP-003 12VDC, 500mA Plug Pack
1
$145.00
$12.00
$8.77
$14.55
5+
less 10%
less 10%
less 10%
less 10%
Modbus-VantagePro2 Gateway
Our Modbus to Davis VantagePro2 Weather Station Gateway allows you
to easily connect your PLC (Programmable Logic Controller), RTU
(remote telemetry unit) or SCADA System to a Davis Vantage Pro2
Weather Station. Using the Modbus RTU protocol it enables your programmable controller to monitor and carry out actions based on wind
speed, wind direction, temperature etc.
Features
*Connect weather station to Gateway
RS232 Com Port 1 Baud rate 19200
*Connect the PLC to Gateway Com port
2.
*PLC Connection can be RS232 or
RS485.
*PLC Connection
selectable Modbus address 1 to 16.
selectable baud rate 2400, 4800,9600 or 19200
selectable parity none, odd, even
*Transfer readings
Outdoor Temperature, Humidity
Wind Speed, Wind Direction
Rainfall (Precipitation)
Barometric Pressure
Indoor Temperature and Humidity (console)
Solar Radiation Evaporative Transfer
Daily, Monthly, Yearly Rainfall
* Communications OK status between the weather station and gateway
Price Each
1
5+
GWY-140 Modbus to Davis VantagePro Weather Station Card $139.00 less 10%
GWY-141 Modbus to Davis VantagePro Card DIN Rail
$159.00 less 10%
Modbus-VantagePro2 Weather Stations
The first and only weather station in its class to
use frequency hopping spread spectrum radio
technology to transmit weather data wirelessly
up to 1000' (300 m).
Includes Vantage Pro2 console/receiver, integrated sensor suite, and mounting hardware. Integrated sensor suite
includes rain collector, temperature and humidity sensors, anemometer,
40' (12 m) anemometer cable, and solar panel. Electronic components
are housed in a weather-resistant shelter.
Sensor suite is solar powered. Electronic components are housed in a
weather-resistant shelter. Console may be powered using the included
AC-power adapter or with three C batteries (not included).
Wireless range is up to 1000' (300 m) outdoors, line of sight. Typical
range through walls under most conditions is 200' to 400' (60 to 120 m).
Add wireless repeaters for distances up to 1.7 miles (2.7 km).
OCEAN CONTROLS - CONTROLLERS
TRIP Amplifier or Analog Monitor Card
The Dual Trip Alarm or Alarm Monitor allows you to monitor 0-20mA, 4-20mA and 0-5V analog signals analog signals. Alarm 1 has 10 different modes
of operation. Alarm 2 has 9 different modes of operation.
The Dual Alarm monitor is easily configured by a PC program via its serial port. All alarm parameters are stored into the
non volatile EEPROM memory. Configurations can be saved to your PC’s hard drive
Modes include
- High Level Alarm. A relay is switched on when the analog input level remains above a specified High Level. Relay is
switched off on returning to Low Level
- Low Level Alarm. A relay is switched on when the analog input level remains below a specified Low Level. Relay is
switched off on returning to High Level
- High Low Level Alarm. A relay is switched on when the analog input level remains above a specified High Level or
below a specified Low Level.
Can be used to on-off control of pumps, compressors, ovens etc
Price Each
ALM-001 Trip Alarm/Alarm Monitor
ALD-001 Trip Alarm/Alarm Monitor DIN Rail Mount
1
$79.50
$109.50
5+
less 10%
less 10%
OCEAN CONTROLS - COUNTERS & TIMERS
7 Digit LCD Counter
7 Digit LCD Timer
This self powered counter (internal battery) can count up to 9999999 and retains data at least 10 years. It comes in
two forms the CH-7N (accepts NPN signals) and the CH-7P (accepts PNP signals). The maximum input signal frequency is 20Hz.
It also features a reset switch on the front
panel
This self powered timer (internal battery)
comes in two forms TH-7NM and the TH
-7NH.
The TH-7NM accepts a NPN signal or
relay contact to common and counts up
to 999999.9 minutes.
The TH-7NH accepts a NPN signal or
relay contact to common and counts up
to 999999.9 hours.
Both types retain data for at least 10 years.
They also feature a reset switch on the front panel
Ambient Operating Temperature 0 to 50degC
Ambient Operating Humidity 35 to 85%RH
Measure 45(W)x22(H)x48(D)mm
Ambient Operating Temperature 0 to 50degC
Ambient Operating Humidity 35 to 85%RH
Measure 45(W)x22(H)x48(D)mm
Price Each
CH-07N 7 Digit LCD Counter NPN Input
CH-07P 7 Digit LCD Counter PNP Input
1
$42.50
$42.50
5+
less 10%
less 10%
Price Each
TH-7NM 7 Digit LCD Minute Timer
TH-7NH 7 Digit LCD Hour Timer
Multi Function Programmable Timer
This timer from Crouzet would have to be the most flexible timer in the market. Features include
7 timing ranges - 1s - 10s - 1min - 1hr - 10hr - 100hr
10 different functions
Supply Voltage 12 - 240V AC/DC
Output - 1 Change over relay
DIN rail mountable
Price Each
TIM-001 Crouzet Mur3 Multi Function Timer
Page 39 Ocean Controls Catalog 2009
1
$84.00
5+
less 10%
1
$42.50
$42.50
5+
less 10%
less 10%
OCEAN CONTROLS - COUNTERS & TIMERS
Square Wave Oscillator
Multi Function Programmable Timer Kit
This simple kit, based on the popular
555 timer IC. It generates six preset
frequencies - 1Hz, 10Hz, 100Hz,
1KHz, 10KHz and 100KHz. The output is selected by setting a jumper
position (J1 to J6). It has a wide operating voltage (5-18V) and even provides visual indication (LED) of the
output. A 9V battery snap is provided
and a suitable mounting box sup-
This timer supports up
to 7 different modes of
operation. It can be
programmed with a
delay time of 1 second
to 2550 minutes. Can
switch up 240VAC @
5A. Perfect for Watchdog Timer applications.
Price Each
KIT-141 As Kit
KTA-141 Assembled Timer
1
$33.50
$48.50
5+
less 10%
less 10%
Price Each
KIT-111 As Kit
KTA-111 Assembled and Tested
This is a low cost 4 Digit Up
Down. As a count up counter its
range is from 0000,1,2.. to
9999. It can also count down.
Inputs include "Reset", "Count",
"Count Direction" and
"Disable". It also has an
"Overflow" output for connecting to another counter which
allows an 8 Digit counter to be
made.
A low cost 4 digit presettable down
counter with output and reset. The
starting count value can be set using 2
pushbuttons. The counter can be used
for both high and low speed counting
applications. The counter has 4 operating modes that control how the output
behaves when the count reaches zero.
1
$33.00
5+
less 10%
Clear Top Bulkhead Case
Page 40 Ocean Controls Catalog 2009
Price Each
KIT-154 As Kit
1
$33.00
5+
less 10%
Dual Cyclic Timer or Pulse Generator
The 4 Digit timers and Up Down Counters can be mounted in our clear
Bulkhead Plastic case to give a budget priced sealed timer. The case
has a clear top that allows you to view the contents of the box.
Measures 120x70x30mm.
Price Each
CAS-001 Clear Top Bulkhead Case
5+
less 10%
less 10%
4 Digit Presettable Down Counter
4 Digit Up Down Counter
Price Each
KIT-129 As Kit
1
$20.00
$35.00
1
$10.86
10+
less 10%
For each cyclic timer you can configure the width of the high and low
portion of the pulse (0 to 9999999.9
secs) and the number of pulses (1
to 9999999). A 0 for the number of
pulses indicates endless pulses. A
led indicates when the cyclic timer
is finished. Two digital inputs control the operation of the timer. An
enable pin starts the timer. A reset
pin causes the cyclic timer pulses
to restart again .
The Dual Cyclic Timer is easily
configured by a PC program via its
serial port. All parameters are stored into EEPROM memory.
Price Each
1
CYC-001 Cyclic Timer / Pulse Generator Card
$79.50
CYC-002 Cyclic Timer / Pulse Generator on DIN Rail $109.50
5+
less 10%
less 10%
OCEAN CONTROLS - COUNTERS & TIMERS
Programmable 6 Digit Counter
Programmable Timer
With a 4 digit display, this timer offers a
relay output to be switched at preprogrammed intervals according to eleven
different timing functions. The LED display
shows the running time and the digital
inputs execute start, hold and reset funstions. Dimensions: 48x48mm x 100mm
(1/16 DIN).
This programmable 6-digit counter is also a
batch counter and totalizer, per forms
quadrature counting and accepts remote reset.
Its 2 outputs with built-in timers can be
activated at any of the 3 counter presets: unit,
batch or totalizer.
It features a special function key, full scale
adjustment and several other advanced
configuration options.
- Input types: (2 for counting, 1 reset) type
NPN/PNP, dry contact (relay, switch, etc) or voltage pulse.
- Max. count frequency: 50 Hz or 10 kHz.
- Counter scale factor: 0.00001 to 9.99999.
- Counting: UP or DOWN.
- F key: counter hold, counter reset, outputs reset.
- Outputs: 1 SPST relay and 1 pulse 5 V/25 mA output.
- Output timer: 10 ms to 9999 s.
- Power: 100~240 Vac/dc ±10% or 24 Vdc/ac.
- Internal battery for data hold.
- Sensor supply output: 12 Vdc/50 mA.
- IP65 UL94 V-2 front panel; IP20 UL94 V-0 enclosure; silicone rubber
keypad.
-Size: 48 x 48 x 110 mm.
Features Include
Input types:NPN/PNP, dry contact and
voltage pulse.
Output type: 3A @ 250Vac relay or 5vdc
voltage pulse.
Display: high efficiency10mm LED.
Switching power supply: 12-24Vdc/ac or 85-264Vac.
Dimensions: 48x48mm x 100mm.
Up and down counting.
Eleven different timer modes. One mode is user defined.
Three digital inputs for special functions.
Frontal key to execute one pre-programmed special function.
Programmable time range from 0.01 second to 9999 hours.
Price Each
TIM-010 Programmable Timer 240VAC
TIM-011 Programmable Timer 24VDC
1
$119.00
$119.00
5+
less 10%
less 10%
7 Day Digital Timer
This 7 Day Digital Timer can switch
on and off up to 10 times per day.
Has a 'random' function which turns
appliances on and off at nonspecified times between the hours
6pm and 6am (great for when you
are on holiday). Also features a
countdown timer which may be used
to turn appliances on or off after a
specified time interval. .
Price Each
TIM-021 7 Day Digital timer
Page 41 Ocean Controls Catalog 2009
1
$22.68
Price Each
1
5+
NOV-400 6 Digit Counter Relay+Pulse Out 240VAC $129.00 less 10%
NOV-401 6 Digit Counter Relay+Pulse Out 24VDC $129.00 less 10%
NOV-405 6 Digit Counter Relay+Pulse RS485 240VAC $129.00 less 10%
NOV-405 6 Digit Counter Relay+Pulse RS485 24VDC $129.00 less 10%
OCEAN CONTROLS - ELECTRICAL PARTS
Universal DIN Rail Terminals
Type(IEC ROHS)
W/T/H(mm)
Voltage(V)
Current(A)
Rigid cable (mm2)
Soft cable (mm2)
SKJ-2.5
42.5/5.2/46.5
800
32
1.0-4/AWG24-12
1.0-2.5/AWG24-12
Our new line of DIN-Rail terminals will impress both on quality and price. If
you would like a free sample pack to inspect then email us
SKJ-4
42.5/6.2/46.5
800
41
0.2-6/AWG24-10
0.2-4/AWG24-10
Price Each
TRM-007 SKJ-2.5 Universal 2.5mm Terminal
TRM-010 SKJ-4 Universal 4mm Terminal
TRM-013 SKJ-6 Universal 6mm Terminal
TRM-016 SKJ-10 Universal 10mm Terminal
TRM-019 SKJ-16 Universal 16mm Terminal
TRM-022 SKJ-35 Universal 35mm Terminal
1+
$0.99
$0.99
$1.39
$1.89
$2.39
$4.10
SKJ-6
42.5/8.2/46.5
800
57
0.2-10/AWG24-8
0.2-6/AWG24-8
SKJ-10
42.5/10.2/46.5
800
76
0.5-16/AWG20-6
0.5-10/AWG20-6
SKJ-16
42.5/12.2/50.5
800
101
2.5-25/AWG12-4
4-16/AWG12-4
SKJ-35
50.5/15.2/61
1000
150
0.75-50/AWG18-00
0.75-35/AWG18-00
SKJ-10RD
62.4/12.2/56
660
10
0.5-16/AWG12-4
0.5-16/AWG12-4
Fuse
Yes
SKJ-2.5SK
52/6.2/46
400
16
0.2-4/AWG24-12
0.2-4/AWG24-12
Switch
No
10+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
Fuse and Switch DIN Rail Terminals
Type(IEC ROHS)
W/T/H(mm)
Voltage(V)
Current(A)
Rigid cable (mm2)
Soft cable (mm2)
Fuse or Switch
LED Indication
SKJ-2.5RD
58.5/8.0/43.5
660
6.3
0.2-4/AWG24-12
0.2-2.5/AWG24-12
Fuse
No
SKJ-4RD
72.5/8.2/56
660
6.3
0.2-4/AWG24-12
0.2-4/AWG24-12
Fuse
No
Price Each
TRM-041 SKJ-2.5RD Fuse Terminal
TRM-044 SKJ-4RD Fuse Terminal
TRM-047 SKJ-4RD/X Fuse Terminal
TRM-050 SKJ-10RD Fuse Terminal
TRM-053 SKJ-10RD/X Fuse Terminal
TRM-056 SKJ-2.5SK Test Switch
1+
$2.19
$2.39
$3.12
$3.45
$4.50
$2.45
SKJ-4RDX
72.5/8.2/56
660
6.3
0.2-4/AWG24-12
0.2-4/AWG24-12
Fuse
Yes
SKJ-10RD
62.4/12.2/56
660
10
0.5-16/AWG12-4
0.5-16/AWG12-4
Fuse
No
10+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
Earth DIN Rail Terminals
Type(IEC ROHS)
W/T/H(mm)
Torque(Nm)
Current(A)
Rigid cable(mm2)
Soft cable (mm2)
SKJ-2.5JD
42.5/5.2/46
0.5-0.7
SKJ-4JD
64/6.2/46.4
0.5-0.7
0.2-6/AWG24-12 0.2-6/AWG24-12
0.2-2.5/AWG24-12 0.2-4/AWG24-12
Price Each
TRM-071 SKJ-2.5JD Earth Terminal 2.5mm
TRM-074 SKJ-4JD Earth Terminal 4mm
TRM-077 SKJ-6JD Earth Terminal 6mm
TRM-091 SKJ-6JD Earth Terminal 10mm
Page 42 Ocean Controls Catalog 2009
1+
$2.25
$2.29
$2.69
$1.99
SKJ-6JD
42.5/8.2/46
1.5-1.8
SKJ-10JD
42.5/8.2/46
1.5-1.8
0.2-10/AWG24-8
0.2-6/AWG24-8
0.5-16/AWG20-6
1.5-10/AWG20-6
10+
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - ELECTRICAL PARTS
Jumpers For Terminals
Type(IEC ROHS)
SJK-2.5
SJK-4
SJK-6
SJK-10
SJK-16
10 Way Internal Jumper
SFB1-10-5
SFB1-10-6
SFB1-10-8
SFB1-10-10
SFB1-10-12
10 Way External Jumper
SEB2-10-5
SEB2-10-6
SEB2-10-8
SEB2-10-10
SEB2-10-12
Price Each
1+
TRM-092 SFB1 10-6 INTERNAL JUMPER for SJK4
$1.99
TRM-093 SFB1 10-8 INTERNAL JUMPER for SKJ6
$2.29
TRM-094 SFB1 10-10 INTERNAL JUMPER for SJK-10 $2.79
TRM-095 SFB1 10-12 INTERNAL JUMPER for SJK-16 $3.25
TRM-101 SEB 10-5 EXTERNAL JUMPER for SKJ2.5
$1.50
TRM-102 SEB 10-6 EXTERNAL JUMPER for SKJ4
$1.99
TRM-103 SEB 10-8 EXTERNAL JUMPER for SJK6
$2.29
TRM-104 SEB 10-10 EXTERNAL JUMPER for SJK10
$2.99
10+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
Accessories for Terminals
Type IEC ROHS
Description
Suitable for
SKJ2G/2
End Clamp
All SKJ Terminals
SKJ-B1
Label
All SJK Terminals
Price Each
TRM-111 SKJ-2.5XG END PLATE
TRM-112 SKJ-2G2 END CLAMP
TRM-113 SKJ-B1 MARK SEAT
TRM-114 SKJ-G(ATP-UK) GROUPING STOP
TRM-115 SKJ-G(DUK) END PLATE
1+
$0.59
$0.69
$0.69
$0.79
$0.59
SKJ-G(ATP-UK)
Grouping Clap Board
SJK 2.5 to 16 Terminals
10+
less 10%
less 10%
less 10%
less 10%
less 10%
Plastic Cable Glands
IP68 CE RoHS
PG TYPE
Material: nylon plastic
Hermetic seal: nitrile rubber
Ambient temperature:
quiescent state -40degC to 100degC,
short time to 120degC
dynamic
-20degC to 80degC,
short time to100degC.
Supply color: Grey,Black, Other color please inquire
Price Each
CGL-001 PG7 Grey Cable Gland
CGL-004 PG9 Grey Cable Gland
CGL-007 PG11 Grey Cable Gland
CGL-010 PG13.5 Grey Cable Gland
CGL-013 PG16 Grey Cable Gland
CGL-016 PG19 Grey Cable Gland
CGL-019 PG21 Grey Cable Gland
CGL-022 PG25 Grey Cable Gland
CGL-025 PG29 Grey Cable Gland
Page 43 Ocean Controls Catalog 2009
1+
$1.50
$1.60
$1.70
$1.80
$1.90
$2.00
$2.10
$2.30
$2.75
10+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
SKJ-G(DUK)
End Plate
SJK 2.5 to 16 Terminals
OCEAN CONTROLS - ELECTRICAL PARTS & ENCLOSURE
23-16 Standard Din-rail Enclosure 101x115x45 mm
Heatshrink Tubing
Size: 101x115x45 mm
Material—Aluminium Cover and Bottom
IP Protection Class: no
Battery: no
Temperature Rating 125degC
Voltage Rating 600V
Flammability VW-1
Certificated by UL. CSA.
Sizes range from 1.5 to 50mm dia
Supply color: Black,Red and Blue
Sold in 1 metre lengths
Price Each
ENC-001 23-16 Standard Din-rail Enclosure 101x115x45 mm
1
$17.50
23-16A Standard Din-rail Enclosure 101x115x45 mm
Size: 101x115x45 mm
Material—Aluminium Cover and Bottom
IP Protection Class: no
Battery: no
Price Each
HSH-001 Black 1metre 1.5/0.75
HSH-002 Black 1metre 2.5/1.25
HSH-003 Black 1metre 3.5/1.75
HSH-004 Black 1metre 5.0/2.5
HSH-005 Black 1metre 7.0/3.5
HSH-006 Black 1metre 10/5.0
HSH-007 Black 1metre 15/7.5
HSH-008 Black 1metre 20/10
HSH-009 Black 1metre 25/12.5
HSH-010 Black 1metre 30/15
HSH-011 Black 1metre 40/20
HSH-012 Black 1metre 50/25
HSH-021 Red 1metre 1.5/0.75
HSH-022 Red 1metre 2.5/1.25
HSH-023 Red 1metre 3.5/1.75
HSH-024 Red 1metre 5.0/2.5
HSH-025 Red 1metre 7.0/3.5
HSH-026 Red 1metre 10/5.0
HSH-027 Red 1metre 15/7.5
HSH-028 Red 1metre 20/10
HSH-029 Red 1metre 25/12.5
HSH-030 Red 1metre 30/15
HSH-031 Red 1metre 40/20
HSH-032 Red 1metre 50/25
HSH-041 Blue 1metre 1.5/0.75
HSH-042 Blue 1metre 2.5/1.25
HSH-043 Blue 1metre 3.5/1.75
HSH-044 Blue 1metre 5.0/2.5
HSH-045 Blue 1metre 7.0/3.5
HSH-046 Blue 1metre 10/5.0
HSH-047 Blue 1metre 15/7.5
HSH-048 Blue 1metre 20/10
HSH-049 Blue 1metre 25/12.5
HSH-050 Blue 1metre 30/15
HSH-051 Blue 1metre 40/20
HSH-052 Blue 1metre 50/25
1+
$0.75
$0.90
$1.10
$1.30
$1.60
$2.00
$2.80
$3.10
$3.90
$4.80
$6.10
$7.50
$0.75
$0.90
$1.10
$1.30
$1.60
$2.00
$2.80
$3.10
$3.90
$4.80
$6.10
$7.50
$0.75
$0.90
$1.10
$1.30
$1.60
$2.00
$2.80
$3.10
$3.90
$4.80
$6.10
$7.50
10+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
22-23 Industrial Control Enclosure 115x90x40 mm
Size: 115x90x40 mm
Material—ABS Plastic
IP Protection Class: no
Battery: no
Price Each
ENC-002 23-16A Standard Din-rail Enclosure 101x115x45 mm
23-14 Standard Din-rail Enclosure 101x115x55 mm
Size: 101x115x55 mm
Material—Aluminium Cover and Bottom
IP Protection Class: no
Battery: no
Price Each
NC-003 23-14 Standard Din-rail Enclosure 101x115x55 mm
Page 44 Ocean Controls Catalog 2009
1
$15.95
1
$17.50
23-14A Standard Din-rail Enclosure 101x115x55 mm
Size: 101x115x55 mm
Material—Aluminium Cover and Bottom
IP Protection Class: no
Battery: no
Price Each
ENC-004 23-14A Standard Din-rail Enclosure 101x115x55 mm
1
$23.50
22-62 Industrial Control Enclosure 115x90x41 mm
Size: 115x90x41 mm
Material—ABS Plastic
IP Protection Class: no
Battery: no
Price Each
ENC-005 22-62 Industrial Control Enclosure 115x90x41 mm
Price Each
ENC-006 22-23 Industrial Control Enclosure 115x90x40 mm
1
$23.50
1
$15.95
OCEAN CONTROLS - MICROCONTROLLER PROGRAMMERS
AVRISP-MKII In-System Programmer
AVR Programmer
The Atmel® AVRISP MK2 ( AVRISP MKII Communication Protocol ) is an InSystem Programmer for Atmel's AVR® Flash microcontrollers. The AVRISP MK2
gives the designer a compact and reliable programming tool to program all InSystem Programmable AVR microcontrollers through a 6 pin ISP connector.
The AVRISP MK2 uses AVR Studio®, Atmel's Integrated Development Environment (IDE) for code writing and debugging.
The programming software can be controlled from both a Windows® environment
and a DOS command-line interface.
This is a simple to use USB AVR programmer. It is
low cost, easy to use, works great with AVRDude,
and is tested under Windows, Linux, and MacOS X.
Based on Dick Steefland's USBtiny and Limor Fried's
USBtinyISP.
o AVR Studio Operated
o USB Serial In-System Programming
o USB Interface to PC
o Upgrades are done from AVR Studio
o Target Voltage 2.7 - 6.0V
o Powered from Target. No Need for Additional Power
Supply
This programmer works really well for ATmega168
and ATmega328 and should work with all the AVR
micros supported by AVRDUDE. We've played a bit with the ATtinys but we cannot
guarantee that this board will be compatible with anything but ATmega168/328.
This board is buffered and power protected so that you can do some really evil
things to the programmer without killing it. It is fast! Comparable speed to the AVR
ISP2 USB programmer from Digikey. One of the greatest features of this board is
the ability to power the target (up to 500mA) from the programmer.
Price Each
PRG-001 AVRISP-MKII In-System Programmer
1
$75.00
To use this programmer, attach to a windows machine and install the drivers listed
below. Open a command prompt. Assuming WinAVR (and therefore AVRDUDE)
have been installed, type:
avrdude -c usbtiny -B 1 -patmega328 -U flash:w:main.hex
AVR Programming Adapter
Be sure to include the "-B 1" flag as this will significantly increase the programming
speed! You may need to change -p flag to your appropriate microcontroller. You
can setup a tool and hotkey in Programmers Notepad to do this automatically.
This is a simple, but extremely handy board to adapt the common 10-pin ISP programmers to the smaller 6-pin ISP connections and vice-versa. Also designed in is a 6-pin inline connector so that you can insert this board directly into a breadboard!
Good for the AVRISP-MKII. Pin 1 indicators indicate how the
AVR-PG1 and PG2 should be oriented.
Board comes bare.
Price Each
PRG-002 AVR Programming Adapter
Cable is about 200mm long.
1
$2.50
AVR - ICSP Adapter
This is an adapter assembly that converts 2x5 pin connector
to 2x3 pin mini-ICSP. Comes with a mini-ICSP cable terminated female at both ends. The adapter board comes terminated as male 2x3 pin to female 2x5 pin.
Price Each
PRG-003 AVR to ICSP Adapter
1
$9.95
MPLAB Compatible ICD2 with USB
Description:
PIC-ICD2-POCKET is the world's smallest PIC ICD2 debugger
and programmer, with only 55 x 55 mm (2.16 x 2.16") dimensions and
only 30gr weight (without ICSP cable and packing) this little device fits in your
pocket and is very convenient to carry with you when you work in field. PIC-ICD2POCKET is completely replacement of Microchip's original MPLAB-ICD2 and with
it you can do everything you can do with the original MPLAB-ICD2, the only difference is that MPLAB-ICD2 have also RS232 while PIC-ICD2-POCKET operates
only from USB. PIC-ICD2-POCKET is a low cost, real-time debugger and programmer for selected PIC® MCUs and dsPIC® DSCs.
Programs can be downloaded, executed in real time and examined in detail with
the debug functions of MPLAB. Set watch variables and breakpoints from symbolic
labels in C or assembly source code, and single step through C source lines or into
assembly code. PIC-ICD2-POCKET can also be used as a development programmer for supported MCUs. The secret behind In Circuit Debugging is two dedicated
hardware lines (microcontroller pins used only during debugging mode) that control
In Circuit Serial Programming™ (ICSP™) of the device and, afterwards, debugging
through proprietary, on-chip firmware. The ICD 2 debug features are built into the
microcontroller and activated by programming the debug code into the target processor. There is some shared overhead expense that includes one stack level,
some general purpose file registers and a small area of program memory.
Features:
* USB (Full Speed 2 M bits/s) interface to host PC
* Real time background debugging
* MPLAB IDE GUI (latest release available for free
download from Microchip's web site)
* Built in over-voltage/short circuit monitor
* Firmware upgradeable from PC
* Light plastic enclosure
* Supports low voltage to 2.0 volts. (2.0 to 6.0 range)
* Diagnostic bi-color LED (Busy, Error)
* USB power status green LED
* Reading/Writing memory space and EEDATA
areas of target microcontroller
* Programs configuration bits
* Erase of program memory space with verification
* Peripheral freeze-on-halt stops timers at breakpoints
Page 45 Ocean Controls Catalog 2009
Price Each
PRG-004 Pocket AVR Programmer
1
$21.50
MPLAB Compatible ICD2 with USB and RS232
Description:
The popular ICD2 by Olimex. This is complete drop in replacement for the Microchip ICD2
at a fraction of the cost. A low cost development tool
providing real time emulation for all PICs with the builtin ICD feature. Operates through RS232 or USB. More
information about the ICD2 can be found on Microchip's web site.
Uses standard DB9 serial cable or USB cable. USB
cable should be 'B' Male (ICD2) to 'A' Male (Computer).
The large PIC on the ICD2 is a 16F877 that stays on the board. It is what does all
the magic. The ICD2 can only be used through the ICSP port - there is no
'programming' socket on the unit itself.
Note: MPLab 8.xx has a bug that affects the RS232 interface on the ICD2. If using
version 8.xx of Microchip's MPLab, you will need to use the USB interface or any
of the version 7.xx IDEs. This bug affects not only Olimex ICD2s, but the original
MPLab ICD2 from Microchip as well.
Dimensions: 3.8x3.3"
Price Each
PRG-011 MPLAB Compatible ICD2 with USB and RS232
1
$139.01
MPLAB Compatible Tiny-ICD2
Description:
The new, lower cost Tiny-ICD2 has all the
functionality of the much higher priced ICD2 from
Microchip! Compact, low cost development tool providing
real time emulation for all PICs with build-in ICD feature.
Operates through RS232 only. A complete replacement
of Microchip's MPLAB-ICD2. More information can be
found on the Microchip web site.
Unit requires a 15VDC 2.1x5.5mm center positive external power supply. We do
not currently carry an adapter of this size but you might try Jameco or Digikey.
Note: MPLab 8.xx has a bug that affects the RS232 interface on the ICD2. If using
version 8.xx of Microchip's MPLab, you will need to use an ICD2 with a USB interface (available in the related items below) or any of the version 7.xx IDEs. This bug
affects not only Olimex ICD2s, but the original MPLab ICD2 from Microchip as
well.
Price Each
PRG-012 MPLAB Compatible Tiny-ICD2 with RS232
Price Each
PRG-010 MPLAB Compatible ICD2 with USB
1
$155.30
1
$76.36
OCEAN CONTROLS - ROBOTICS & MOTOR CONTROLLERS
SMC-200 DMC5400 Advanced 4-axis Stepping & Servo
Motion Control Card
The DMC5400 is an advanced 4-axis motion control card for stepping and digital servo control application. Compared with the
DMC1000 and DMC3400 series, DMC5400 offers better linear and
circular interpolation capability and continuous contouring performance for advanced pulse output
motion control solutions.
Features
32-bit PCI bus, Rev. 2.2, 33MHz
Pulse output r rate up to 5MHz
6 Pulse/dir output modes: Pulse /DIR, CW/CCW etc
2~4 axes linear interpolation
2 axes circular interpolation
Multi-axis continuous interpolation
Position/speed change on-the-fly
13 home return modes and auto home search
4 axes incremental encoders input with 28-bit up/down counter
Hardware position compare and trigger with auto-loading FIFO
High speed position latch function
32 General-Purposed I/O
Manual pulser input interface
Programmable acceleration and deceleration time
Trapezoidal and S-curve velocity profiles
Multi-axis, simultaneous start/stop
Programmable interrupt sources
Supports up to 5 cards in one system (20 axes)
Hardware backlash compensator
Software limit function
Easy interface to any stepping and digital servo
Pololu Low Voltage Dual Serial Motor Controller
This low-voltage dual serial
motor controller (DSMC) is designed specifically for highperformance, low-voltage toy
motors that run on 1.5 - 6 V.
Serially controlled it uses PWM
to control the motor speed
Specifications:
PCB size: 25 x 22.5mm, Motor ports: 2
Speeds: 127 forward and backward, brake
Max current: two motors 5 A each, one motor 10 A
Motor voltage: 0 - 7 V
Logic voltage: 3 - 5.5 V
PWM frequency: two motors 600 Hz, one motor 750 Hz
Serial baud rate: 1200 - 192000 (automatically detected)
Price Each
1
POL-120 Low Voltage Dual Serial Motor Controller $53.50
5+
less 10%
Price Each
SMC-200 DMC5400 Multi Axis Controller
SMC-201 TB60 Cable and Terminal Board
SMC-202 TB50 Cable and Terminal Board
1
$1049.00
$149.00
$149.00
Pololu's Micro Dual Serial Motor Controller
Pololu's popular micro motor controller will get your robot running in
a snap. The tiny module can individually control two motors, and
you can daisy-chain multiple units
to control up to 62 motors with one
serial line. The new version provides up to 2 A to a single motor,
or 1 A each to two motors. The
motor supply can be as low as 2 V, making the unit a perfect
match for small DC motors. Using one serial output from your
microcontroller, you can independently set each motor to go
forward or backward at any of 127 speeds, coast, and with the
new version, brake.
Price Each
POL-411 Micro Dual Serial Motor Controller
1
$43.14
5+
less 10%
Pololu 3-Amp motor Controller
The 3-Amp motor controller with multiple interface and feedback options simplifies servo control of commonly available DC motors. The module features three independent interfaces: a serial protocol for microcontroller-based applications, a pulse-width interface for connection to hobby radio control equipment or
serial servo controllers, and an analog voltage interface for simple tests and demonstrations. Two feedback
alternatives allows for closed-loop control of position or speed. The motor controller measures 36 x 36mm
and has an operating voltage of 6–18 volts. The serial protocol is compatible with other Pololu motion control devices, allowing multiple units to be connected to a single serial
Price Each
line to control a mixture of motors sizes and hobby RC servos.
POL-392 3 Amp Motor Controller
Page 46 Ocean Controls Catalog 2009
1
$64.30
5+
less 10%
OCEAN CONTROLS - ROBOTICS & MOTOR CONTROLLERS
Pololu Hi Current Motor Controller
Pololu TReX Dual High Power Motor Driver
The TReX can control two bidirectional
and one unidirectional motor via three
independent control interfaces: radio
control (RC) servo pulses, analog voltage, and asynchronous serial (RS-232
or TTL). It uses five input channels to
receive the RC or analog control signals. When operating in RC or analog
mode, the five channels function as
follows:
* Channel 1: motor 1 speed and direction or, if in mix mode, turn left/right
* Channel 2: motor 2 speed and direction or, if in mix mode, go forward/
reverse
* Channel 3: auxiliary (unidirectional) motor speed
* Channel 4: can be used to enable "flipped mode", which allows invertable robots to be controlled as normal when they are inverted
* Channel 5: determines whether the motors are controlled by the channel inputs or the serial interface; this channel allows you to switch between
autonomous and human control at will .
Price Each
POL-777 TReX Dual Motor Controller
1
$124.50
5+
less 10%
The Pololu highpower motor drivers
are compact carriers
for the VNH3SP30
and VNH2SP30 motor driver integrated
circuits from ST. All
you need to add is a
microcontroller or
other control circuit
to turn the H-Bridge
on and off. The motor drivers have a maximum current rating of 30 A continuous.
The actual current you can deliver depends on how well you
can keep the motor driver cool. In our tests, we were able to
deliver short durations (on the order of milliseconds) of 30 A
and a few seconds of 20 A without overheating. At 6 A, the
chip gets just barely noticeably warm.
Price Each
POL-705 30 Amp Motor Driver with VNH3SP30
POL-706 30 Amp Motor Driver with VNH2SP30
1
$39.65
$47.60
5+
less 10%
less 10%
Pololu Dual Hi Current Motor Controller
The Pololu dual high-power motor drivers are compact carriers for the VNH3SP30 and
VNH2SP30 motor driver IC’s. The board incorporates most of the components of the typical
VNH2SP30 application including pull-up and current-limiting resistors and a FET for reverse
battery protection. (The current sense circuit is populated on both versions of the board,
but only the VNH2SP30 supports current sense.) To keep the number of I/O lines down, the
two enable/diagnostic lines on each chip are tied together. All you need to add is a microcontroller or other control circuit to turn the H-Bridges on and off.
In a typical application, the power connections are made on one end of the board, and the
control connections are made on the other end. +5 volts must be supplied to the board;
the input voltage is available at those pins as well, but the connection is not intended for
currents exceeding a few amps. The diagnostic pins can be left disconnected if you do not want to monitor the
fault conditions of the motor drivers. INA and INB control the direction of each motor, and the PWM pins turns the motors on or off. For Price Each
POL-707 Dual Motor Driver with VNH3SP30
the VNH2SP30 version, the current sense (CS) pins will output apPOL-708 Dual Motor Driver with VNH2SP30
proximately 0.13 volts per amp of output current.
Pololu High Power Motor Controller with Feedback
The SMC04 highpower motor controller with feedback
has multiple interface and feedback
options that simplify
servo control of
commonly available
DC motors. The
module features
three independent interfaces: a serial protocol for microcontroller-based applications, a pulse-width interface for connection to hobby radio control equipment or serial servo controllers, and an analog voltage interface for simple tests and demonstrations. Two feedback alternatives allows for closed-loop
control of position or speed. The SMC04 is higher-current version of our 3-A motor controller with feedback that can handle
larger motors with its VNH3SP30 motor driver chip.
Price Each
POL-425 Hi Power Motor Controller with Feedback
Page 47 Ocean Controls Catalog 2009
1
$123.80
5+
less 10%
1
$64.95
$77.95
5+
less 10%
less 10%
Micro Serial Servo Controller
The Pololu micro serial servo
controller is a very compact
solution for controlling up to
eight radio control (RC) servos
from a computer or microcontroller. The controller measures just 23 x 23mm, yet it is
one of the most full-featured
servo controllers available.
Each servo speed and range
can be controlled independently, the baud rate is detected automatically over a 120038400 bps range, and multiple units can be daisy-chained on
one serial line to control up to 128 servos. Three status LEDs
and an integrated level converter for RS-232 applications get
you up and running quickly. The micro serial servo controller is
dwarfed by even a standard servo, but it can control any standard RC servos, including giant 1/4-scale servos.
Price Each
POL-207 Micro Serial Servo Controller
1
$34.5
5+
less 10%
OCEAN CONTROLS - MOTOR CONTROLLERS
Pololu's Serial 8 Servo Motor Controller
DC Servo Motor Controller
The Pololu serial 8-servo controller allows
you to control up to eight RC servos with
almost any robot controller or computer.
The interface to the servo controller is a
standard RS-232 serial port or a TTL-level
serial line, using any baud rate between
1200 and 38400 baud. Multiple 8-servo
controllers can be connected to a single
serial line to control up to 128 servos independently. The servo controller is compatible with all of our serial motor controllers
and servo controllers. The servo controller
is also compatible with the Scott Edwards
MiniSSC II servo controller and any software written for it.
Price Each
POL-727 Serial 8 Servo Motor Controller
This PIC Servo Motor Driver can
simultaneously drive up to four
servo motors using potentiometers as positioning controllers.
Each motor is positioned by rotating a potentiometer which is connected to the input of the microcontroller.
You need one potentiometer per
motor. The PIC Servo Motor
Driver uses a PIC16C71. All the
work is done in the micro-controller. Full source code supplied. Servomotors & potentiometers not supplied.
Power Supply Required: 5V DC/1A. PCB: 75 x 50mm.
1
$38.10
5+
less 10%
Pololu's USB 16 Servo Controller
Price Each
KIT-102 As Kit
KTA-102 Assembled and Tested
1
$32.50
$42.50
5+
less 10%
less 10%
8 Servo Motor Controller
The Pololu USB 16-servo controller is
the latest addition to our line of R/C
hobby servo controllers. The compact
module measures just 1.9"x1.0" including the USB connector, making it
smaller than most 8-channel controllers, and it offers both USB and asynchronous serial (UART) connectivity.
No features are compromised for the
small size, as our USB controller
supports independent speed and
range settings for each servo while
delivering 0.5-microsecond resolution
for smooth output across its broad output pulse range of 250 through
2750 microseconds. .
Our 8 RC Servo Motor Controller can be configured to
control 4 RC servo motors by
switches (motor moves to two
different positions based on a
switch) and 4 servos via
RS232 ASCII serial commands. Being able to control
the position of the servos by
a switch allows a servo motor
to be used easily in open - closed situations such as road or
door barriers. It is perfect for use with model trains, hobby
models, robotics and industrial production.
The card can easily be configured to have all 8 servos controlled serially. Up to 4 boards can be operated off the one
PC serial port allowing up to 32 motors to be controlled.
Price Each
POL-390 USB 16 Servo Controller
USB-003 USB 2.0 Plug A to 5 Pin Mini B Cable
Price Each
KTA-199 8 Servo Motor Controller assembled
1
$103.25
$9.05
5+
less 10%
less 10%
Pololu's Orangutan Controller
Page 48 Ocean Controls Catalog 2009
1
$75.45
5+
less 10%
Pololu's Round Robot Chassis
The Orangutan robot controller is a
complete control solution for small robots. Orangutan includes an 8character x 2-line liquid crystal display,
two bi-directional motor ports, a buzzer,
three pushbuttons, and up to 12 user I/
O lines, yet the compact module measures only 2.00" x 1.85" and weighs less
than 1 ounce. Because of the complete
feature set, very few additional components (such as sensors or motors) need
to be added to complete the electronic portion of a small robot.
Orangutan is based on the Atmel MEGA168 microcontroller, which
features 16 Kbytes of flash program memory, 1024 bytes of SRAM,
and 512 bytes of EEPROM. Up to 8 channels of 10-bit analog-todigital conversion is also available. Because the user has direct access to the microcontroller, any development software for Atmel's
AVR microcontrollers, including Atmel's free AVR Studio and the GCC
C compiler, is compatible with Orangutan. An in-circuit programmer
such as Atmel's affordable AVR ISP is required for programming
Price Each
POL-225 Orangutan Controller
1
$55.00
5+
less 10%
This circular laser-cut plastic robot
chassis makes a great base for
small mobile robots. With a diameter of only five inches (slightly bigger than a CD), this acrylic chassis
is ideal for building sturdy robots
capable of navigating tight spaces.
As shown below, the circular chassis has many holes and slots for
mounting sensors, motors, and
other hardware.
To complete the round robot chassis, the kit includes a Tamiya twinmotor gearbox, ball caster, and
truck tires; .
Price Each
1
POL-250 Robot Chassis with gearbox motor and tyres $55.00
5+
less 10%
OCEAN CONTROLS - MOTOR CONTROLLERS
DC Motor PID Speed Controller
Hi Current DC Motor Speed Controller
Our new kit provides feedback control of
DC Motors. It can operate in Closed
Loop PID mode allowing accurate speed
control over different loads or in Open
Loop PWM mode.
Target Speed and PID settings can be
set via the 3 Pushbuttons and LCD, the
Serial Port or Analog Input
(potentiometer). Serial Port control allows you to control a number of controllers from the one serial port on your PC.
With this kit you can control the speed of
a common DC motor rated up to 55V
(20A) without sacrificing motor
torque. Operates on a supply voltage of 8V to 26V.
It uses a microcontroller to pulse-width modulate two high current power
IRFZ44 MOSFETs to provide high torque DC Motor Speed Control.
Feedback is achieved with a Photo-Interrupter Pulse (Provided).
Finished Dimensions (mm): 100Wx100Lx40H.
Price Each
KTA-194 DC Motor PID Speed Controller
1
$105.00
5+
less 10%
Serial Hi Current DC Motor Speed ConThe operation of this 20A DC Motor Speed
Controller is configured using a serial port
of a PC. It has 4 different modes of operation.
Mode 1 - Speed is set by ASCII commands received from a serial RS232 connection. Up to 4 Speed Controllers can be
addressed and controlled from a single PC or microcontroller serial port.
Mode 2 - 4 selectable speeds can be chosen using a 4 position rotary
switch
Mode 3 - Motor speed is controlled by a 1-2mS RC Pulse.
Mode 4 - Motor speed is controlled by a PWM pulse stream received
from a PLC or microcontroller
With this kit you can control the speed of a common DC motor rated up
to 55V (20A) without sacrificing motor torque. The controller logic operates on a supply voltage of 8V to 26V. It uses a microcontroller to pulsewidth modulate two high current power IRFZ44 MOSFETs to provide
high torque DC Motor Speed Control.
PWM Frequencies of 9.7KHz, 1.2KHz, 152Hz and 38Hz can be selected
using a serial command.
A straight through D9 Male to Female serial cable is required to configure and communicate with the controller via a PC. The PC software
supplied is a Visual Basic program with source code provided for you to
be able to write your own programs to control the motor from your PC.
Price Each
KTA-207 Serial Hi Current DC Motor Controller
1
$89.00
5+
less 10%
This DC motor controller uses PWM Pulse
Width Modulation to control the speed of a
DC motor. A potentiometer can be used to
set the speed or a 0 to 5VDC signal can be
supplied.
With this kit you can control the speed of a
common DC motor rated up to 55V (20A)
without sacrificing motor torque. Operates
on a supply voltage of 8V to 26V.
Uses a microcontroller to pulse-width modulate two high current power
IRFZ44 MOSFETs to provide high torque DC Motor Speed Control.
This controller is suitable for controlling Golf Buggy DC Motors. A
customer recently said this was the best controller he had used with his
Golf Buggy Motor.
Finished Dimensions (mm): 100Wx100Lx40H. .
Price Each
KTA-195 Hi Current DC Motor Controller
1
$79.00
5+
less 10%
Mini DC Motor Speed Controller in
With this kit control the speed of any
common DC motor rated up to 35V and
8A without sacrificing motor
torque. Operates on a supply voltage of
8V to 35V.
Uses a microcontroller to accurately
pulse-width modulate a high current
power MOSFET, IRFZ44. Also features adjustable acceleration time, potentiometer, 0-5V or 4-20mA input signal control.
Die Cast Box mounted.
Finished Dimensions (mm): 35Wx89Lx30H.
Price Each
KTA-246 Mini DC Motor Speed Controller
1
$69.00
5+
less 10%
DC Motor Speed Controller
With this kit control the speed of
any common DC motor rated up
to 100V (5A) without sacrificing
motor torque. Operates on a supply voltage of 5V to 15V.
Uses NE556 to pulse-width modulate a high current power MOSFET, IRFZ44.
In this way motor torque is maintained. Adjustable speed control. Box
mounted. Finished Dimensions (mm): 60Wx100Lx30H.
Price Each
KIT-067 As Kit
KTA-067 Assembled and Tested
1
$26.50
$44.00
5+
less 10%
less 10%
TB6612FNG Dual Motor Driver Carrier
This tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two
bidirectional DC motors. An operating range of 4.5 – 13.5 V and peak current output of 3 A per channel (1 A continuous) make this a great motor driver for low-power motors.
In a typical application, power connections are made on one side of the board and control connections are made on
the other. All of the control inputs are internally pulled low. Each of the two motor channels has two direction control
pins and a speed control pin that accepts a PWM input with a frequency of up to 100 kHz. The STBY pin must be
driven high to take the driver out of standby mode.
Specifications
Price Each
* Motor voltage (VMOT): 4.5 – 13.5 V
POL-713 TB6612FNG Dual Motor Driver Carrier
* Logic voltage (VCC): 2.7 – 5.5 V
* Output current maximum: 3 A per channel
* Output current continuous: 1 A per channel (can be paralleled to deliver 2 A continuous)
* Maximum PWM frequency: 100 kHz
Page 49 Ocean Controls Catalog 2009
1
$21.21
5+
less 10%
OCEAN CONTROLS - MOTOR CONTROLLERS
Dual Bidirectional DC Motor Speed Controller
This DC motor controller allows you to control
the speed of two DC motors independently. Each
motor can be operated in unidirectional mode
with a 0-5V input giving 0-100% PWM and a
digital input for direction selection, or in bidirectional mode where the analog input is responsible for direction and speed selection.
A link allows you to control the speed from a 020mA or 4-20mA signal. A serial command allows you to set the PWM
frequency to 10KHz, 1.25KHz or 156Hz to suit your application.
Finished Dimensions 75x105x20mm .
Price Each
KTA-198 Dual Bidirectional DC Motor Controller
1
$79.00
5+
less 10%
Bidirectional DC Motor Speed Controller
This kit controls the speed of a DC motor in both
the forward and reverse direction using pulse
width modulation PWM. The range of control is
from fully OFF to fully ON in both directions.
The maximum voltage available to run the motor
is 32VDC.
Price Each
KIT-166 As Kit
KTA-166 Assembled and Tested
1
$34.50
$49.50
5+
less 10%
less 10%
Modbus Programmable Stepper Motor Controller
The introduction of a more powerful microcontroller has
allowed us to produce a standalone 4 axis stepper
motor controller which can be programmed via a PC
using supplied software or alternatively controlled via a
PLC to free the PLC from complex stepper motor control routines. Up to 4 cards can be controlled from a
PLC using the Modbus protocol.
Up to 120 instructions can be programmed into the
controller (1 motor, 50 instructions for 4 motors) and
retained through power loss. Just program once and
then let it go.
Ideal for repetitive process tasks involving stepper motors, the unit can also be configured with up to 6 simple digital outputs (when the outputs are not being used for
motor control) and 4 digital inputs which can be used for limit switches or program
control.
Price Each
1
KTA-193 Modbus Programmable Stepper Controller $119.00
5+
less 10%
The KTA-264 DC Motor Actuator
allows a user to drive and control the
position of a DC gearhead motors. The motor
drives a load and is also physically coupled to a quadrature encoder, photo-interrupter or potentiometer. The
position to move the motor is given by a serial command from a PC, PLC or other type of controller or a
by an externally mounted ON-OFF switch connected to the card. The position
of the DC motor is determined by the wiper of a potentiometer or the quadrature encoder A and B signals connected to the card.
For a quadrature encoder or photo interrupter the position is restricted to the
range -2000000000 to +2000000000
For a potentiometer the position of the motor is restricted to the range of 0 1023.
At the end of each movement the position is saved to EEPROM. When the
end of movement is reached the power will be removed from the motor. The
inertia of the gearhead motor will be expected to hold the load in position.
Please note control of a gearhead motor is not as precise as a stepper or
servo motors with expected errors of movement of +/- 5-10 degrees.
Please note potentiometers have a typical life of 100,000 movements. Hence
this actuator using a potentiometer feedback is not suited to quick repetitive
movements. Also because of the limited range of 0 to 1023 it is only suited to
short movements.
To prevent damage to the potentiometer the range for the MOVA instruction
is limited to between 20 to 1000 when using the KTA-264 with a potentiometer.
Page 50 Ocean Controls Catalog 2009
Small 1, 2 or 3 axis stepper motor drivers with full, 1/2, 1/4 and 1/16
micro-step modes.
Features
- Control motors up to 2.5A
- Supply voltage up to 30VDC
- Works with 4, 6 and 8 wire motors
- Current adjusted by on board trim pot
- Step and Direction inputs
- Plug in Connectors
- Small size 58x47x31mm (KTA-261)
The KTA-261, 262 and 263 are Bipolar Stepper Motor Drivers capable of
controlling 4, 6 and 8 wire stepper motors at up to 2.5A. As well as full
stepping, half, quarter and sixteenth micro-step modes are available,
giving 200, 400, 800 or 3200 steps per revolution for standard 1.8° degree motors.
KTA-261 is capable of controlling 1 motor, KTA-262 up to 2 motors and
KTA-263 up to 3 motors.
Price Each
1
KTA-261 1 Axis Microstepping Stepper Motor Controller $79.00
KTA-262 2 Axis Microstepping Stepper Motor Controller $149.00
KTA-263 3 Axis Microstepping Stepper Motor Controller $214.00
1
$139.00
5+
less 10%
5+
less 10%
less 10%
less 10%
KTA-190 Serial Stepper Motor Controller
Connects to the PC serial port and provides
an easy to use interface for connecting and
controlling stepper motors by your PC. You
can connect up to four KT5158 Bipolar
Stepper Motor Drivers (See Below) or
KT5179 Unipolar Stepper Motor Drivers to
the card using their step and direction signals. You can multidrop up to 4 interface
cards off the 1 RS232 serial line so you can
control up to a total of 16 stepper motors.
Simple ACSII commands are sent to the card to control each of the
stepper motors
@01 AMOV 2000 move stepper motor 1 to position 2000
Allows acceleration and deceleration of the motors and limit switches
can be connected to the card
Price Each
KTA-190 Serial Stepper Motor Controller
DC Motor Actuator
Price Each
KTA-264 DC Motor Actuator
KTA-261 / KTA-262 / KTA-263 Microstepping Bipolar Stepper Motor
Drivers
1
$65.00
5+
less 10%
KTA-208 Dual Pulse Generator
Features
- 2 Pulse Generators
- 0 to 5V Square wave pulses
- RS-232 9600, 8N1 ASCII Serial Controlled
- Add more units to control up to 16 Motors
- Up to 100KHz for each pulse output.
- Ramp up and down adjustable
- Parameters can be stored in Non-Volatile EEPROM
- 5V Pulse and Direction Signal Levels
- 5V Output for Opto-Coupler Drive
- 2 SPST 5A Relays for Control
- 12V or 24VDC Powered
- up to 4 cards off the 1 serial port.
Summary
The KTA-256 Pulse Generator features 2 Pulse Generators. It has been
primarily been designed to interface to stepper and servo motor drives.
Each pulse generator has a direction output associated with it. A negative frequency will result in the direction output having a 0V output while
a positive frequency results in a 5V output. The outputs cannot be connected directly to our stepper drives
Price Each
KTA-208 Dual Pulse Generator
1
$65.00
5+
less 10%
OCEAN CONTROLS - MOTOR CONTROLLERS
12.5kHz Relay Card
Features
• Senses 12.5kHz “Charge Pump” or
“Heartbeat” from CNC control systems for safety
shut-off if the controller fails
• Microcontroller-based for high reliability
• 3.3V and 5V input signal compatible
• On-board 5A SPDT
• Auxiliary coil output for larger relay
• 12V and 24V versions
• DIN rail mount option
• 72mm X 42mm
Summary
The KTA-253 Relay Card is designed to sense a 12.5kHz “Charge
Pump” or “Heartbeat” signal from a CNC controller and activate the relay
when the signal is present. Mach 3 and other CNC controllers can provide this signal as a safety feature. Should the controller fail or the computer hang, crash or lose power, the signal disappears. The KTA-253 is
designed as a safety system to shut down CNC equipment in the event
of controller failure, but also has other uses like preventing erratic movement as Windows starts up and polls the parallel port.
The card is equipped with a 5A (resistive) relay. A larger relay can be
wired to the card’s COIL connections. 12V and 24V versions are available both as a PCB or in DIN-rail mount.
Specifications:
Power Supply Vs and COM:
*KTA-253 / KTC-253: 9V – 16V DC (12V Nominal) ~100mA *KTB-253 /
KTD-253: 18V – 30V DC (24V Nominal) ~100mA
12.5kHz Input IN: *-0.5V – 5.5V.
Relay activation range: 3kHz – 15kHz.
*Signal must drop below 0.3V and rise above 0.7V to be sensed. (3.3V
TTL and 5V TTL compatible)
Auxiliary Relay Connection COIL: Up to 450mA
Relay Output NO C NC: Single-pole, double-throw relay rated to 5A
(resistive). 240VAC / 30VDC
Price Each
KTA-253 12.5kHz Relay Card 12V Card
KTB-253 12.5kHz Relay Card 24V Card
KTC-253 12.5kHz Relay Card 12V Card DIN Rail Mount
KTD-253 12.5kHz Relay Card 24V Card DIN Rail Mount
1
5+
$35.00 less 10%
$35.00 less 10%
$48.50 less 10%
$48.50 less 10%
Our Parallel Port Relay card allows you to
control stepper motor operations from your
parallel port. It uses a 74HC245 buffer IC to
provide protection for your PC’s parallel port
and enough current drive for turning on and
off opto-isolator inputs. Can be connected to
our stepper motor driver cards and Microstepping drives. The card provides 8 motor control
output signals ( 4 Step signals, 4 Direction
signals) to control up to 4 Stepper Motor Drivers, 4 digital inputs designed for use as limit switch inputs, 2 Relay Outputs to control spindles, coolant or vacuums, and 3 general IO which are
connected directly to the port. The card is available with 12V or 24V relays
and requires power at the relay voltage. . Perfect for a 3 axis or 4 axis
CNC machine. Pin outs are suitable for most desk top CNC packages.
Price Each
KTA-205 Parallel Port Interface with 12V Relays
KTA-206 Parallel Port Interface with 24V Relays
1
$45.00
$45.00
5+
less 10%
less 10%
M542 Microstepping Bipolar Stepper Driver
The M542 is a high performance microstepping driver. It is suitable for driving any 2phase and 4-phase hybrid stepping motors.
By using advanced bipolar constant-current
chopping technique, it can output more speed
and power from the same motor, compared
with traditional technologies such as L/R drivers. Features
- Supply voltage +20 to +45VDC,
- Adjustable peak current 0.54 to 4.2A
- The current reduction switches in on absence of clock pulses
- Suitable for 2-phase and 4-phase stepping motors
- Optically isolated input signals
- Pulse frequency up to 400 KHz
- 15 selectable resolutions up to 25000 steps/rev
- Short-circuit, over-voltage, short-voltage protection
- Small size (118x75.5x33mm)
Price Each
1
SMC-003 M542 Microstepping Stepper Motor Controller $149.00
M325 Microstepping Bipolar Stepper Driver
The M325 is a high performance microstepping driver. It is suitable for
driving any 2-phase and 4-phase hybrid stepping motors. By using advanced bipolar constant-current chopping technique, it can output more
speed and power from the same motor, compared with traditional technologies such as L/R drivers. Features
- Supply voltage 12 to +24VDC
- Adjustable peak current 0.39 to 2.5A
- The current reduction switches in on
absence of clock pulses
- Suitable for 2-phase and 4-phase stepping motors
- Optically isolated input signals
- Pulse frequency up to 100 KHz
- Selectable microstep resolutions 1,2,4
and 8
- Small size (86x55x20.5mm)
Price Each
1
SMC-002 M325 Microstepping Stepper Motor Controller $99.00
KTA-205 Parallel Port Interface Card with Relays
5+
less 10%
M415 Microstepping Bipolar Stepper Driver
The M415B is a very small size high performance
microstepping driver. It is suitable for driving any 2phase and 4-phase hybrid stepping motors. By
using advanced bipolar constant-current chopping
technique, it can output more speed and power
from the same motor, compared with traditional
technologies such as L/R drivers. Features
- High Performance Low Cost
- Supply voltage 18 to +36VDC
- output current adjustable from 0.1A to 1.5A
- Inaudible 20khz chopping frequency
- TTL compatible and optically isolated input signals
- Automatic idle-current reduction
- Mixed-decay current control for less motor heating
- 7 selectable resolutions (1,2, 4, 8, 16, 32, 64)
- Microstep resolution can be changed on the fly (optional)
- Suitable for 2-phase and 4-phase stepping motors
- Reverse polarity protection
Price Each
1
SMC-006 M415 Microstepping Stepper Motor Controller $109.00
Page 51 Ocean Controls Catalog 2009
5+
less 10%
5+
less 10%
OCEAN CONTROLS - MOTOR CONTROLLERS
ND556 Microstepping Bipolar Stepper Driver
DM556 Fully Digital Microstepping Bipolar Stepper Motor Driver
The ND556 is a high performance microstepping driver using pure-sinusoidal wave current
control technology, it is particularly suitable for
applications which require extremely low noise
and low heating. The ND556 is suitable for a
wide range of stepping motors of NEMA 17,
23 and 34 size
Features include
- Patented technology
- Pure-sinusoidal precise current control technology
- Extreme low motor noise
- Both driver and motor low heating
- High performance, low cost
- Supply voltage +20 to +45VDC, Adjustable peak current 1.4 to 5.6A
- The current semi-reduction automatically switches in on absence of
clock pulses
- Suitable for 4,6,8 lead motors
- Optically isolated input signals
- Pulse frequency up to 400 KHz
The DM556 is a versatilite fully digital stepping driver
based on a DSP with advanced control algorithm. The
DM556 is the next generation of digital stepping motor
controls. It brings a unique level of system smoothness, providing optimum torque and nulls mid-range
instability. Motor self-test and parameter auto-setup
technology offers optimum responses with different
motors and easy-to-use. Tuning software is freely
available which allows your PC to serially connect to
the drive and tune the performance of your motor. The
driven motors can then run with much smaller noise, lower heating,
smoother movement than most of the drivers in the markets. Its unique
features make the DM556 an ideal solution for applications that require
low-speed smoothness.
Price Each
1
SMC-004 ND556 Microstepping Stepper Motor Controller $179.00
5+
less 10%
DM856 Fully Digital Microstepping Bipolar Stepper Motor Driver
The DM856 is a versatility fully digital stepping driver based on a DSP with advanced
control algorithm. The DM856 is the next
generation of digital stepping motor controls.
It brings a unique level of system smoothness, providing optimum torque and nulls midrange instability. Motor auto-identification and
parameter auto-configuration technology
offers optimum responses with different motors and easy-to-use. The driven motors can run with much smaller noise,
lower heating, smoother movement than most of the drivers in the markets.
Its unique features make the DM856 an ideal solution for applications that
require low-speed smoothness.
Compared to the DM432, broader input voltage and output current ranges
make the DM856 can drive more motors than the DM432. What’s more,
owing to its higher performance DSP, driven motors can achieve much
higher speed (above 3000RPM) than that of the DM432, offering servo-like
performances. It can be regarded as an improved model origin from DM556,
while supports broader input voltage range.
Features
- Anti-Resonance, provides optimum torque and nulls mid-range instability
- Motor self-test and parameter auto-setup technology, offers optimum responses with different motors
- Multi-Stepping allows a low resolution step input to produce a higher microstep output for smooth system performance
- Microstep resolutions programmable, from full-step to 102,400 steps/rev
- Supply voltage up to +80VDC
- Output current programmable, from 0.5A to 5.6A
- Pulse input frequency up to 200 KHz
- TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protections
Price Each
1
5+
SMC-009 DM856 Microstepping Stepper Motor Controller $225.00 less 10%
What’s more, owing to its higher performance DSP, driven motors can
achieve much higher speed (above 3000RPM), offering servo-like performances.
Features
- Anti-Resonance, provides optimum torque and nulls mid-range instability
- Motor self-test and parameter auto-setup technology, offers optimum
responses with different motors
- Multi-Stepping allows a low resolution step input to produce a higher
microstep output for smooth system performance
- Microstep resolutions programmable, from full-step to 102,400 steps/
rev
- Supply voltage up to +50VDC
- Output current programmable, from 0.5A to 5.6A
- Pulse input frequency up to 200 KHz
- TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protections
Price Each
1
5+
SMC-007 DM556 Microstepping Stepper Motor Controller $189.00 less 10%
DM432 Fully Digital Microstepping Bipolar Stepper Motor Drivers
The DM432 is a versatility fully digital stepping driver based on a DSP with
advanced control algorithm. The DM432 is the next generation of digital
stepping motor controls. It brings a unique level of system smoothness, providing optimum torque and nulls mid-range instability. Motor autoidentification and parameter auto-configuration technology offers optimum
responses with different motors and easy-to-use. The driven motors can run
with much smaller noise, lower heating, smoother movement than most of
the drivers in the markets. Its unique features make the DM432 an ideal
solution for applications that require low-speed smoothness.
Features
- Anti-Resonance, provides optimum torque and nulls mid-range instability
- Motor auto-identification and parameter auto-configuration technology,
offers optimum responses with different motors
- Multi-Stepping allows a low resolution step input to produce a higher microstep output for smooth system performance
- Microstep resolutions programmable, from full-step to
102,400 steps/rev
- Supply voltage up to +40 VDC
- Output current programmable, from 0.3A to 3.2A
- Pulse input frequency up to 200 KHz
- TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protections
Price Each
1
SMC-008 DM432 Microstepping Stepper Motor Controller $99.00
Page 52 Ocean Controls Catalog 2009
5+
less 10%
OCEAN CONTROLS - MOTOR CONTROLLERS
KTA-191 Bipolar Chopper Stepper Motor Driver Kit
MD882 Microstepping Bipolar Stepper Driver
The MD882 is a high performance microstepping driver using pure-sinusoidal
wave current control technology. It is particularly suitable for applications desired
with extremely low noise and low heating.
Tthe pure-sinusoidal precise current control technology (domestic patented technology) ensures long motor life and high
torque and the operating effect of the stepping motor is somehow inclined to that of
servo motor.
Features
- Pure-sinusoidal precise current control technology
- Supply voltage up to +75VDC
- Peak current to 8.2A (RMS5.86A)
- Optically isolated differential input pulse frequency up to 300 KHz
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase stepper motors
- 16 selectable resolutions up to 10000 steps/rev
- DIP switch current setting with 8 different values
Price Each
1
SMC-005 MD882 Microstepping Stepper Motor Controller $225.00
5+
less 10%
Price Each
KTA-191 Bipolar Motor Chopper Drive Assembled
Simple circuit to drive 4 wire (and 6 or 8
wire) bipolar stepper motors at up to 8
amps. The card features
- a double sided PCB - screw Terminals
for all inputs, power and motor connections.
- Full and Half Step (less resonance problems) and microstepping of 4,8,16,32,64
and 128 operation
- Step and Direction Inputs.
- an enable input which will remove all power to the motor
Supply Required: 8-30V DC
We tested the KT5196 against a K158 and found an increase of 33% in
stepping rate performance.
5+
less 10%
The KT-5197 is a combination of our
popular KT5190 Serial Stepper Controller
and the KT-5196 Bipolar Stepper Motor
Driver.
It has all the features of the KT-5196
including full and half stepping and enable input.
You simply write ASCII commands
through the PC's serial port to the card to
control the stepper motor
@01 AMOV 2000 move stepper motor 1 to position 2000
Up to 4 of these cards can be controlled from a serial port.
Dimensions 75x105x20mm .
Price Each
KTA-197 Assembled and Tested
Dimensions 75x105x20mm .
1
$65.00
1
$85.00
KTA-197 Serial Bipolar Stepper Motor Controller
KTA-196 Bipolar Stepper Motor driver
Price Each
KTA-196 Assembled and Tested
Our new bipolar chopper drive allows you to get better performance from
your stepper motor.
It uses a dual full bridge motor driver based
on the L297 & L298. Motor current for each
phase is set using an on-board potentiometer and the controller is capable of handling
motor winding currents up to 2 Amps per
phase.
It operates from a DC supply voltage of 936V. The drive provides all basic motor
controls, including full or half stepping of
bipolar steppers and direction control.
Works with our range of large bipolar stepper motors
Signals (Step, Direction, Enable) can be interfaced to external logic or a
microcontroller. Can easily control the motor from your computer's parallel port or our serial stepper controller card!
Finished Dimensions (mm): 88Wx105Lx35H
1
$95.00
5+
less 10%
5+
less 10%
EasyDrive Bipolar Stepper
KTA-206 Serial Unipolar Stepper Motor
The KT-5206 is a combination of our popular KT5190 Serial Stepper Controller and a
Unipolar Stepper Motor Driver.
The new card features
- accepts the same serial ASCII commands as the KT-5190 to drive the motor
eg @01 RMOV 10000
- accelerate and decelerate motors
- control up to 4 KT-5206's from the one RS232 serial port
- accepts a 0-5V signal to control the speed of the stepper motor.
- a double sided PCB (more reliable and no links to solder).
- screw terminals for all inputs, power and motor connections.
- Full and Half Step (less resonance problems) operation
- Step and Direction Input.
- an enable input which will remove all power to the motor .
Dimensions 75x105x20mm .
Price Each
KTA-206 Assembled and Tested
Page 53 Ocean Controls Catalog 2009
1
$95.00
5+
less 10%
EasyDriver v3 is a simple to use
bipolar stepper motor driver,
compatible with anything that can
output a digital 0 to 5V pulse.
The EasyDriver requires a 7V to
30V supply to power the motor,
and has an on board voltage
regulator for the digital interface. Connect a 4-wire stepper motor and a
microcontroller and you've got precision motor control!
Caution: Do not connect or disconnect a motor while the driver is energized. This will cause permanent damage to the A3967 IC.
Features:
* A3967 driver configured for 8-microstep mode
* Compatible with 4, 6, and 8 wire stepper motors
* Adjustable current control from 150mA/phase to 750mA/phase
* Power supply range from 7V to 30V. The higher the voltage, the
higher the torque
Dimensions 43 x 21 x 8mm
Note at higher currents the A3967 gets hot and may need cooling
Price Each
SMC-020 EasyDriver Bipolar Stepper Drive
1
$19.95
5+
less 10%
OCEAN CONTROLS - MOTOR CONTROLLERS
KIT-179 Unipolar Stepper Motor
Dual Unipolar Stepper Motor Controller
Standard circuit to drive 5, 6 or 8
wire unipolar stepper motors. Can
be operated in free-standing
(internal oscillator) or PC-controlled
(direction, step) mode. Uses
IRFZ44 power MOSFETs to drive
the motors. These MOSFETs have
a low on resistance and can and
can carry 6A each with needing a heatsink. Separate supply voltage for
kit and motors if required. Up to six driver boards (for controlling 6 motors) can be connected to a single PC parallel port.
Connects to the PC printer port & will drive
two unipolar stepper motors up to max. 3A
each. All contained in an extended D-shell
case. Will also accept 4 inputs from external switches. A DOS based software program (also runs under Windows) written
specifically to drive stepper motors is included, complete with C source code. Software provides three run modes and will
half-step, single-step or manual-step motors. Software will run interactively or process a text file of commands.
Price Each
KIT-179 As Kit
KTA-179 Assembled and Tested
Price Each
KIT-113 As Kit
KTA-113 Assembled and Tested
1
$25.00
$39.00
5+
less 10%
less 10%
DC Servo Motor Controller
5+
less 10%
Stepper Motor Power Supply
The DB810A is a digital DC servo driver
developed with CPLD and high efficient
MOSFET technologies. In position control, it’s easy for end users to change
stepping drivers to the DB810A without
changing control systems, because its
input command is PUL/DIR signal, which
is compatible with that of stepping drivers. In low power motion control applications, performances of DC servo systems
using the DB810A are better than those of digital AC servo systems in
velocity, precision, noise, stability, or at least as good as those of digital
AC servo systems. However, the cost of the DB810A stays at the price
line of stepping driver, namely far lower than those of AC servo drivers..
Features
- 18-80VDC, 0-20A, 20-400W
- PID feedback servo drive
- Feedback resolution ×4 encoder line count
- Lock range +/- 128 count following error
- Opto-isolated pulse and direction inputs (differential)
- Over-current and short-circuit protection
Small size 110 x 69 x 27mm - Weight - 0.45Kg
Price Each
SMC-240 DB810A Servo Motor Drive
1
$34.50
1
$229.00
5+
less 10%
SPS series power supplies are switchable
DC power supplies specifically designed
for stepping & servo driver. Normal regulated switchable power supplies usually
work with bad variability and low efficiency
when used in stepping or servo driving.
This is because conventional switching
power supplies are designed for the constant, unvarying loads of circuit boards. With stepping or servo systems
inductive loads are being switched so the driving current vary quickly.
This supply is capable of delivering current to motor drivers without affecting the reliability due to its unregulated specialty and bulky capacitance. By selecting the correct model, one supply can supply 1 to 3
motors and so the average cost per shaft is saved.
Features
- Compact size, lightweight 112×102×55mm Weight - 0.45Kg
- Output power 300W (continuous work)
- Short circuit, over-current & over-voltage
- Input Supply 240VAC
Models
- SPS-407 output 7A continuous at 40V (9A Peak current).
- SPS-487 output 7A continuous at 48V (9A Peak current).
- SPS-705 output 5A continuous at 70V (7A Peak current).
Price Each
SMC-100 40V Power Supply
SMC-105 48V Power Supply
SMC-110 70V Power Supply
1
$129.00
$129.00
$149.00
5+
less 10%
less 10%
less 10%
OCEAN CONTROLS - CNC PACKAGES
50 oz-in Frame 17 Mini 3 Axis CNC Pack
125 oz-in High Speed CNC Pack
The CNC-001 3 Axis Package includes
3 x Hi-Speed MOT-120 Stepper Motors
3 x M325 Stepper Motor Drivers (1,2,4 and 8
Microstepping)
1 x 150W 24VDC Power Supply
1 x Parallel Port Interface KTA-192
1 x Wiring Diagram
The CNC-002 3 Axis Package includes
3 x High Speed MOT-124 Stepper Motors
(see Specs)
1 x 3 Axis Driver KTA-263
1 x 150W 24VDC Power Supply
1 x Parallel Port Interface KTA-205
The CNC-102 Additional Axis Package
includes
1 x High Speed MOT-124 Stepper Motors (see Specs)
1 x 1 Axis Driver KTA-261
1 x PSM-002 24VDC 40W Power Supply
The CNC-101 Additional Axis Package includes
1 x High Speed MOT-120 Stepper Motors
(see Specs)
1 x M325 Stepper Motor Driver (1,2,4 and 8 Microstepping)
1 x PSM-002 24VDC 40W Power Supply
Price Each
CNC-001 50 Oz-In Frame 17 Mini CNC Pack
CNC-101 50 Oz-In Frame 17 Additional Axis
Page 54 Ocean Controls Catalog 2009
1
$499.00
$179.00
Price Each
CNC-002 125 oz-in High Speed CNC Pack
CNC-102 125 oz-in High Speed Additional Axis Pack
1
$499.00
$179.00
OCEAN CONTROLS - MOTOR CONTROLLERS
175 oz-in High Speed 3 Axis CNC Pack
262 oz-in High Speed & Torque CNC Pack
The CNC-004 3 Axis Package includes
3 x Hi-Speed Frame 23 MOT-122 Stepper
Motors
3 x M542 Microstepping Drivers (up to
25000 steps per rev)
2 x SPS407 40VDC Stepper Supply
1 x Parallel Port Interface KTA-205
1 x Wiring Diagram
The CNC-005 3 Axis Package includes
3 x Hi-Speed Frame 23 MOT-125 Motors
3 x M542 Microstepping Drivers (up to
25000 steps per rev)
2 x SPS407 40VDC Stepper Supplies
1 x Parallel Port Interface KTA-205
1 x Wiring Diagram
$1012 Value for $859
The CNC-104 Additional Axis Package includes
1 x High Speed Frame 23 MOT-122 Stepper Motor
1 x M542 Microstepping Driver (up to 25000 steps per rev)
The CNC-105 Additional Axis Package includes
1 x High Speed Frame 23 MOT-125 Stepper Motor
1 x M542 Microstepping Driver (up to 25000 steps per rev)
$248 Value for $209
Price Each
CNC-004 175 oz-in High Speed CNC Pack
CNC-104 175 oz-in High Speed Additional Axis Pack
1
$799.00
$189.00
262 oz-in Hi-Speed & Torque CNC Pack
Price Each
CNC-005 262 oz-in High Speed CNC Pack
CNC-105 262 oz-in High Speed Additional Axis Pack
1
$859.00
$209.00
310 oz-in High Speed & Torque CNC Pack
The CNC-006 3 Axis Package includes
3 x High Speed Frame 23 MOT-125 Motors
3 x ND556 Low Noise Sinusoidal Drivers
2 x SPS407 40VDC Stepper Supplies
1 x Parallel Port Interface KTA-205
1 x Wiring Diagram
The CNC-007 3 Axis Package includes
3 x Hi-Speed Frame 23 MOT-105 Stepper
Motors
3 x ND556 Low Noise Sinusoidal Drivers
3 x SPS407 40VDC Stepper Supply
1 x Parallel Port Interface KTA-205
1 x Wiring Diagram
$1102 Value for $929
$1211 Value for $1029
The CNC-106 Additional Axis Package
1 x High Speed Frame 23 MOT-125 Stepper Motor
1 x ND556 Low Noise Sinusoidal Driver
The CNC-107 Additional Axis Package
1 x High Speed Frame 23 MOT-105 Stepper Motor
1 x ND556 Low Noise Sinusoidal Driver
1 x SPS407 40VDC Stepper Supply
$278 Value for $229
$387 Value for $329
Price Each
CNC-006 262 oz-in High Speed CNC Pack
CNC-106 262 oz-in High Speed Additional Axis Pack
1
$929.00
$229.00
430 oz-in High Torque CNC Pack
Price Each
CNC-007 310 oz-in High Speed CNC Pack
CNC-107 310 oz-in High Speed Additional Axis Pack
1
$1029.00
$329.00
630 oz-in High Torque CNC Pack
The CNC-011 3 Axis Package includes
3 x Frame 24 MOT-128 Stepper Motors
3 x ND556 Low Noise Sinusoidal Drivers
2 x SPS407 40VDC Stepper Supply
1 x Parallel Port Interface KTA-205
1 x 12VDC Plug Pack
1 x Wiring Diagram
The CNC-020 3 Axis Package includes
3 x MOT-130 Stepper Motors
3 x ND556 Low Noise Sinusoidal Drivers
3 x SPS407 40VDC Stepper Supply
1 x Parallel Port Interface KTA-205
1 x 12VDC Plug Pack
1 x Wiring Diagram
$1439 Value for $1219
$1162 Value for $979
The CNC-120 Additional Axis Package includes
1 x MOT-130 Stepper Motor
1 x ND556 Low Noise Sinusoidal Driver
1 x SPS407 40VDC Stepper Supply
The CNC-111 Additional Axis Package includes
1 x Frame 24 MOT-128 Stepper Motor
1 x ND556 Low Noise Sinusoidal Driver
$298 Value for $249
$463 Value for $389
Price Each
CNC-011 430 oz-in High Torque CNC Pack
CNC-111 430 oz-in Additional Axis Pack
Page 55 Ocean Controls Catalog 2009
1
$979.00
$249.00
Price Each
CNC-020 630 oz-in High Torque CNC Pack
CNC-120 630 oz-in Additional Axis Pack
1
$1219.00
$389.00
OCEAN CONTROLS - MOTOR CONTROLLERS
1200 oz-in High Torque CNC Pack
630 oz-in High Torque CNC Pack
The CNC-022 3 Axis Package includes
3 x MOT-132 Stepper Motors
3 x MD882 Microstepping Drivers
3 x SPS407 40VDC Stepper Supply
1 x Parallel Port Interface KTA-205
1 x 12VDC Plug Pack
1 x Wiring Diagram
1700 oz-in High Speed & Torque CNC
Pack
The CNC-024 3 Axis Package includes
3 x MOT-135 Stepper Motors
3 x MD882 Microstepping Drivers
3 x SPS487 48VDC Stepper Supply
1 x Parallel Port Interface KTA-205
1 x 12VDC Plug Pack
1 x Wiring Diagram
$1697 Value for $1475
$1697 Value for $1439
The CNC-124 Additional Axis Package includes
1 x MOT-135 Stepper Motor
1 x MD882 Microstepping Drivers
1 x SPS487 48VDC Stepper Supply
The CNC-122 Additional Axis Package includes
1 x MOT-132 Stepper Motor
1 x MD882 Microstepping Drivers
1 x SPS407 40VDC Stepper Supply
$549 Value for $495
$549 Value for $459
Price Each
CNC-022 1207 oz-in High Torque CNC Pack
CNC-122 1207 oz-in Additional Axis Pack
1
$1439.00
$459.00
3 Axis DC Servo CNC Pack
Price Each
CNC-024 1700 oz-in High Torque CNC Pack
CNC-124 1700 oz-in Additional Axis Pack
3 Axis DC Servo CNC Pack
The CNC-015 3 Axis Package includes
The CNC-014 3 Axis Package includes
3 x MOT-280 DC Servo Motors with 1000
line Encoders
3 x DB810A Servo Drives
1 x PSM-201 500W Power Supply
1 x Parallel Port Interface KTA-205
1 x Wiring Diagram
3 x MOT-270 DC Servo Motors with 500
line Encoders
3 x DB810A Servo Drives
2 x PSM-008 Power Supply
1 x Parallel Port Interface KTA-205
1 x Wiring Diagram
$1786 Value for $1499
$1565 Value for $1329
The CNC-115 Additional Axis Package includes
1 x MOT-280 Servo Motor with 1000 line Encoder
3 x DB810A Servo Drive
The CNC-114 Additional Axis Package includes
1 x MOT-270 Servo Motor with 500 line Encoder
3 x DB810A Servo Drive
$468 Value for $394
Price Each
CNC-015 Servo CNC Pack
CNC-115 Servo Additional Axis Pack
Page 56 Ocean Controls Catalog 2009
1
$1475.00
$495.00
$454 Value for $379
1
$1499.00
$394.00
Price Each
CNC-014 Servo CNC Pack
CNC-114 Servo Additional Axis Pack
1
$1329.00
$379.00
OCEAN CONTROLS - MOTORS
MOT-301 Mini Servo 4.8V-6V
MOT-302 Standard Size Power Servo 4.8V-6V
Mini sized servo perfect for R/C or robotics applications where size is at a premium.
Dimensions: 35 x 16.9 x 32mm (L x W x
H)
Weight: 26g
Torque 4.8V: 3.4kg / cm
Transit Time 4.8V: 0.19 sec / 60 deg
Torque 6V: 4.2kg / cm
Transit Time 6V: 0.15 sec / 60 deg
Price Each
MOT-301 Mini Servo 4.8-6V
Standard sized servo suitable for 1/10th
scale R/C cars and robotics applications.
Strong torque for power applications.
1
$27.23
5+
less 10%
MOT-303 Heavy Duty Servo 4.8V-6V
1
$40.91
5+
less 10%
1
$36.32
5+
less 10%
For projects that require brute strength,
look no further than this giant-scale
servo. This servo will deliver eight times
the torque of a standard servo, has two
ball bearings, and has metal gears to
handle those extra-tough loads. Includes Servo Horns
Dimensions: 63.0 x 32.0 x
61.6mm Weight: 160g
Torque 4.8V: 24kg/cm
Transit Time 4.8V: 0.24 sec / 60deg
Torque 6V: 28.8kg / cm
Transit Time 6V: 0.20 sec / 60deg
Price Each
MOT-310 Giant Servo 4.8-6V
MOT-310 Jumbo Servo 4.8V-6V
This is our largest servo and feature
huge torque and speed Features include
ball bearing, high torque and quick
transit time.
1
$75.00
5+
less 10%
Horns for R/C Servo Motors
MOT-304 Packet of 6 mixed servo
horns to suit our Mini Servo and
Standard Sized Servo
Dimensions: 65.0 x 32.0 x 70.4mm (L
x W x H)
Weight: 190g
Torque 4.8V: 35kg/cm
Transit Time 4.8V: 0.15 sec / 60deg
Torque 6V: 42kg / cm
Transit Time 6V: 0.12 sec / 60deg
Price Each
MOT-312 Jumbo Servo 4.8-6V
Price Each
MOT-302 Standard Size Servo 4.8-6V
MOT-310 Giant Servo 4.8V-6V
A heavy duty servo which won't make
a heavy duty dent in your wallet. Features include ball bearing, high torque
and quick transit time.
Dimensions: 54.4 x 26.5 x 51.5mm (L
x W x H)
Weight: 110g
Torque 4.8V: 10kg/cm
Transit Time 4.8V: 0.25 sec / 60deg
Torque 6V: 13kg / cm
Transit Time 6V: 0.20 sec / 60deg
Price Each
MOT-303 Heavy Duty Servo 4.8-6V
Dimensions: 39.5 x 20 x 39.6mm (L x W
x H)
Weight: 46g
Torque 4.8V: 7.2kg / cm
Transit Time 4.8V: 0.33 sec / 60 deg
Torque 6V: 8kg / cm
Transit Time 6V: 0.27 sec / 60 deg
MOT-305 Packet of 2 servo horns to
suit our heavy duty servo
1
$115.00
5+
less 10%
Price Each
MOT-304 Packet of Mixed Servo Horns
MOT-305 Packet of Heavy Servo Horns
1
$6.32
$6.32
5+
less 10%
less 10%
MOT-108 Bipolar Stepper Motor
PM55L-048 Stepper Motor
Industrial grade small Stepper Motor, ideal for
small CNC projects and robots. Has a holding
torque of 0.18Kg.cm (0.018Nm or 2.5oz-in).
Shaft at one end
Features
- Step Angle 1.8deg
- Voltage 3.9V
- Current 0.6A
- Resistance per coil 6.5 Ohm
- Inductance per coil 1.7
- Dimensions: 20mm x 20mm square face, 30mm long, 16mm between
mounting holes
- 4 Leads
- Weight: 0.06Kg
Price Each
MOT-108 Bipolar Stepper Motor
Page 57 Ocean Controls Catalog 2009
1
$22.00
5+
less 10%
Precision Stepper Motor, ideal for small projects and robots, good output characteristics
and small size.
Does not come with connector cable but the
pins are accessible for soldering.
Features
• 55mm Outer Diameter
• High Torque for size
• Step Angle: 7.5deg
• Shaft protrudes through both ends with pinion gear on top
• Dimensions: 55mm Wide, 25mm High, 65mm between mounting
holes, Shaft protrudes ~10mm through each end
Price Each
MOT-004 PM55L-048 Stepper Motor
1
$18.00
5+
less 10%
OCEAN CONTROLS - MOTORS
GEARBOX WITH MOTOR REVERSIBLE 12V 70RPM
This compact unit will give a massive
2.1 kg/cm of torque at 70 RPM. Current draw rises to a modest 390 MA.
SPECS:
Torque
Rated Voltage
Operating
max
Current - No load
Current - Full load
Gear Ratio
Shaft Speed
Only slightly larger than the MO-101,
it has a much larger torque (12.0Kg/
CM) at 36RPM. It is ideal for driving
wheels or other traction devices.
SPECS:
Torque
Rated Voltage
Operating
Current - No load
Current - Full load
Gear Ratio
Shaft Speed
2.1kg/cm
12.0V
4.5 - 18V
30mA
390mA
82:1
70RPM
Price Each
MOT-201 Reversible Gearbox Motor 12V 70RPM
1
$13.59
GEARHEAD MOTOR REVERSIBLE 12VDC - 140RPM
Featuring a torque of 50Kg/cm this
motor is for heavy duty applications.
SPECS:
Torque
Rated Voltage
Operating
Current - No load
Current - Full load
Gear Ratio
Shaft Speed
Weight
1
$40.91
1
$22.68
MO-210 DC MOTOR 12VDC - 11800RPM
Price Each
MOT-210 High Power DC Motor 11800 RPM
1
$16.32
MO-212 DC MOTOR 12VDC - 18800RPM
A compact ferrite magnet type DC Motor featuring hard steel drive shaft, long life design and are
built in an ISO 9002 quality environment.
A compact ferrite magnet type DC Motor featuring hard steel drive shaft, long life design and are
built in an ISO 9002 quality environment.
No load
Speed (RPM) 18800
Current (AMP) 2.6
Operating Range (V) 6-12
At Stall
Torque (kg/cm) 4.9
Current (AMP) 92
At Max Efficiency
Efficiency (%) 71
Power (W) 107
Speed (RPM) 15520
Torque (kg/cm) .67
Current (A) 12.8
No load
Speed (RPM) 9700
Current (AMP) 1.3
Operating Range (V) 6-18
At Stall
Torque (kg/cm) 6.0
Current (AMP) 57
At Max Efficiency
Efficiency (%) 73
Power (W) 52
Speed (RPM) 8490
Torque (kg/cm) .60
Current (A) 6.0
Page 58 Ocean Controls Catalog 2009
Price Each
MOT-202 Reversible Gearbox Motor 12V 36RPM
No load
Speed (RPM) 11800
Current (AMP) 0.8
Operating Range (V) 6-12
At Stall
Torque (kg/cm) 2.7
Current (AMP) 26
At Max Efficiency
Efficiency (%) 76
Power (W) 43
Speed (RPM) 9800
Torque (kg/cm) 0.42
Current (A) 4.7
MO-211 DC MOTOR 12VDC - 9700RPM
Price Each
MOT-211 High Power DC Motor 9700 RPM
12.0kg/cm
12.0V
4.5 - 18V max
70mA
1380mA
244:1
36RPM
A compact ferrite magnet type DC Motor featuring
hard steel drive shaft, long life design and are built
in an ISO 9002 quality environment.
50kg/cm
12.0V
270mA
11.7A
1000:1
140RPM
300g
Price Each
MOT-203 Reversible Gearbox Motor 12V 14RPM
GEARBOX WITH MOTOR REVERSIBLE 12V 36RPM
Price Each
MOT-212 High Power DC Motor 18800 RPM
1
$22.68
1
$20.86
OCEAN CONTROLS - HI PERFORMANCE STEPPER MOTORS
MOT-110 Bipolar Stepper Motor
MOT-115 Bipolar Stepper Motor
MOT-116 Bipolar Stepper Motor
Industrial grade small Stepper Motor, ideal
for small CNC projects and robots. Has a
holding torque of 1.0Kg.cm (0.098Nm or
14oz-in). Shaft at one end
Industrial grade small Stepper Motor, ideal for small CNC projects and
robots. Has a holding torque of 2.0Kg.cm (0.196Nm or 28oz-in). MOT-115:Shaft at
one end; MOT-116: Shaft at two end.
Features
- Voltage 10V
- Current 0.5A
- Resistance per coil 20Ohm
- Inductance per coil 18mH
Dimensions: 35mm x 35mm square face, 36mm long, 26mm between
mounting holes
- 4 Leads
- Weight: 0.18Kg
Price Each
MOT-110 Bipolar Stepper Motor
1
$22.00
5+
less 10%
MOT-120 (Frame 17) Bipolar Stepper Motor
Industrial grade small Stepper Motor, ideal
for small CNC projects and robots. Has a
holding torque of 3.6Kg.cm (0.35Nm or
50oz-in). Shaft at both ends
Features
- Step Angle 1.8deg
- Voltage 2.8V, Current 1.68A
- Resistance per coil 1.65Ohm
- Inductance per coil 3.2mH
Dimensions: 42mm x 42mm square face, 40mm long, 26mm between
mounting holes
- 4 Leads
- Weight: 0.3Kg
• Weight: 0.15Kg
Price Each
MOT-120 Bipolar Stepper Motor
1
$59.00
5+
less 10%
MOT-124 Bipolar Stepper Motor
Industrial grade small Stepper Motor, ideal
for CNC projects and robots. Has a holding
torque of 9.0Kg.cm (0.88Nm or 125oz-in).
Shaft at both ends
Features
- Step Angle 1.8deg
- Voltage 7.4V
- Current 1A
- Resistance per coil 7.4 ohm
- Inductance per coil 10
- Dimensions: 56mm x 56mm square face, 56mm long, 47mm between
mounting holes
- 6 Leads
- Weight: 0.7Kg
Price Each
MOT-124 Bipolar Stepper Motor
Price Each
MOT-125 Bipolar Stepper Motor
Page 59 Ocean Controls Catalog 2009
1
$79.00
5+
less 10%
1
$99.00
Features
- Step Angle 1.8deg
- Voltage 6V
- Current 0.8A
- Resistance per coil 7.5Ohm
- Inductance per coil 6
- Holding Torque 2.0Kg.cm
- Step Angle Accuracy ±5% (full step, no load)
- Resistance Accuracy ±10%
- Inductance Accuracy ±20%
- Temperature Rise 80degC Max.(rated current,2
phase on)
- Ambient Temperature -20 to +50degC
- Insulation Resistance 100MOhm Min. ,500VDC
- Dielectric Strength 500VAC for one minute
- Shaft Radial Play 0.02Max. (450 g-load)
- Shaft Axial Play 0.08Max. (450 g-load)
- Max. radial force 28N (20mm from the flange)
- Max. axial force 10N
• Dimensions: 39mm x 39mm square face, 38mm long, 31mm between mounting
holes
- 6 Leads
- Weight: 0.2Kg
• Shaft Dia 5mm.
- MOT-115: Extends 20mm from 1 end of the motor;
- MOT-116: Extends 20mm from front and 10mm from rear of the motor.
Price Each
MOT-115 Bipolar Stepper Motor
MOT-116 Bipolar Stepper Motor
1
$27.50
$27.50
5+
less 10%
less 10%
MOT-122 (Frame 23) Bipolar Stepper Motor
Industrial grade small Stepper Motor, ideal
for CNC projects and robots. Has a holding
torque of 12.6Kg.cm (1.24Nm or 175oz-in).
Shaft at both ends
Features
- Step Angle 1.8deg
- Voltage 2.5V
- Current 2.8A
- Resistance per coil 0.9ohm
- Inductance per coil 2.5mH
- Dimensions: 56mm x 56mm square face, 56mm long, 47mm between
mounting holes
- 4 Leads
- Weight: 0.7Kg
Price Each
MOT-122 Bipolar Stepper Motor
1
$79.00
5+
less 10%
MOT-125 (Frame 23) Bipolar Stepper Motor
Industrial grade small Stepper Motor, ideal
for CNC projects and robots. Has a holding
torque of 18.9Kg.cm (1.85Nm or 262oz-in).
Shaft at both ends
Features
- Step Angle 1.8deg
- Voltage 3.2V
- Current 2.8A
- Resistance per coil 1.13ohm
- Inductance per coil 3.6mH
- Holding Torque 18.9Kg.cm
Dimensions: 56mm x 56mm square face, 76mm long, 47mm between
mounting holes
- 4 Leads
5+
- Weight: 1Kg
less 10%
• Shaft extends 20mm and 15mm from ends of the motor
OCEAN CONTROLS - HI PERFORMANCE STEPPER MOTORS
MOT-130 Bipolar Stepper Motor
MOT-128 (Frame 24) Bipolar Stepper Motor
Industrial grade small Stepper Motor,
ideal for CNC projects and robots. Has a
holding torque of 31Kg.cm (3.04Nm or
430oz-in). Shaft at both ends
Industrial grade Stepper Motor, ideal for
driving heavier loads. Has a holding torque of
46Kg.cm (4.51Nm or 638oz-in). Shaft at both
ends
Features
- Step Angle 1.8deg
- Voltage 4.2V
- Current 2.8A
- Resistance per coil 1.5ohm
- Inductance per coil 6.8mH
- Holding Torque 31Kg.cm
Dimensions: 60mm x 60mm square face, 88mm long, 47mm between
mounting holes
- 8 Leads
- Weight: 1.4Kg
- Shaft extends 20mm and 15mm from ends of the motor
Features
- Step Angle 1.8deg
- Voltage 2.5V
- Current 5.5A
- Resistance per coil 0.46ohm
- Inductance per coil 4mH
- Holding Torque 46Kg.cm
Dimensions: 86mm x 86mm square face, 80mm long, 69mm between
mounting holes
- 4 Leads
- Weight: 2.3Kg
- Shaft extends 30mm from both ends of the motor
Price Each
MOT-128 Bipolar Stepper Motor
Price Each
MOT-130 Bipolar Stepper Motor
1
$119.00
5+
less 10%
MOT-132 Bipolar Stepper Motor
1
$175.00
5+
less 10%
Bipolar Stepper Motor– Torque 2.2Nm
Industrial grade Stepper Motor, ideal for
driving heavier loads. Has a holding torque
of 87Kg.cm (8.53Nm or 1207oz-in). Shaft
at both ends
This motor is a 23 Frame motor with 4 phases
which you can wire in parallel or serial provides. It has a holding torque of 2.2 N.m
(311oz-in) and is suitable for very heavy operation
Features
- Step Angle 1.8deg
- Voltage 3.6V
- Current 6A
- Resistance per coil 0.6ohm
- Inductance per coil 6.5 mH
- Holding Torque 87Kg.cm
Dimensions: 86mm x 86mm square face, 118mm long, 69mm between
mounting holes
- 4 Leads
- Weight: 3.8Kg
- Shaft extends 30mm from both ends of the motor
Features
• Rated Current: 2.8A (Series), 5.7A(Parallel)
• Phase Resistance 1.6ohm
• Phase Inductance 7.2mH
• Step angle: 1.8deg
• Ambient Temp -10 to 50degC
• Temp Rise 80degC
• Dimensions: 56mm x 56mm square face, 80mm long, 47mm between
mounting holes
• Weight: 1.2Kg
• Shaft extends 20mm from both ends of the motor
Price Each
MOT-132 Bipolar Stepper Motor
Price Each
MOT-105 Bipolar Stepper Motor 57HS22
1
$215.00
5+
less 10%
MOT-135 Bipolar Stepper Motor
Industrial grade Stepper Motor, ideal for
driving heavier loads. Has a holding torque
of 122Kg.cm (11.96Nm or 1694oz-in).
Shaft at one end
Features
- Step Angle 1.8deg
- Voltage 4.65V
- Current 6.2A
- Resistance per coil 0.75ohm
- Inductance per coil 9 mH
- Holding Torque 122Kg.cm
Dimensions: 86mm x 86mm square face, 156mm long, 69mm between
mounting holes
- 4 Leads
- Weight: 5.4Kg
- Shaft extends 30mm from one end of the motor
Price Each
MOT-135 Bipolar Stepper Motor
Page 60 Ocean Controls Catalog 2009
1
$259.00
5+
less 10%
1
$99.00
5+
less 10%
OCEAN CONTROLS - DC SERVO MOTORS
DC Servo Motor
DCM5xxxx series motors are permanent magnet DC brush servo motors. The motors are ideal for cost sensitive
applications. They include an attached encoder which provides position feedback to controllers.
Suitable for a wide range of equipments and instruments such as engraving machines, cutting machines, jet-ink
machines , experimental installations, instructional machines, imager, analytic instruments, electronic packaging
equipments and loading and unloading devices, medical instruments,etc. It performs better in equipments which
expected to be low noise, high precision and high velocity.
Features Include
- High performance (Smooth operation, High precision and Low noise)
- Low cost
- Small disturbance
- Model DCM50205 comes with a 500 line encoder
- Model DCM50207 comes with a 1000 line encoder
- Positional error can be eliminated to one pulse
- Mounting dimensions of DCM57xxx brush servo motors are the same as those of NEMA 23 size motors
Price Each
1
MOT-270 DCM50205 DC Servo Motor with encoder $225.00
MOT-280 DCM50207 DC Servo Motor with encoder $239.00
5+
less 10%
less 10%
ISC3004 SERIES-ROTARY ENCODER
ISC4006 SERIES-Rotary encoder
Shaft diameter Φ4mm, clamping flange, housing
diameter Φ30mm. 500 Pulses/rev Quadrature
Low price at high performance, small volume, light
weight, easy for installing.
Applications:
Measure the speed, and measure the distance, shoe making machines,
molding machines.
Shaft diameter Φ6mm, clamping flange, housing
diameter Φ40mm. 1000 Pulses/rev Quadrature
Low price at high performance, small volume, light
weight, easy for installing.
Applications:
Measure the distance, stop dog positioning, curtained door, textile machines.
Price Each
1
IBE-001 Rotary Encoder ISC3004-701E500B-12-24C $135.00
Price Each
1
5+
IBE-002 Rotary Encoder ISC4006-H03G1000BZ3-5-24C $135.00 less 10%
5+
less 10%
ISM8060-Rotary encoder
The metal raster, the design is modularization, and
the material have plastic and metal.100 Pulses/rev
Quadrature
The unit isφ72×21, the type is thin, and it is very
light, fastness 3M3.
Adapt to the printing and so on.
Price Each
1
IBE-003 Rotary Encoder ISC8060-401G100BZ1-12C $135.00
Page 61 Ocean Controls Catalog 2009
5+
less 10%
OCEAN CONTROLS - HI PERFORMANCE STEPPER MOTORS
Spider Coupler
IBEST DR series (Flexible Coupling)
Connects motors or shafts which are slightly misaligned and absorbs torsional shock. The hubs are
connected by a synthetic rubber spider.
20mm dia
30mm long
6.35mm (1/4") bore
Price Each
MOA-001 Spider Coupler
1
$18.14
D: External diameter of the connector; L: the
long of the connector.
M: The hole dia. of the encoder end. N: the hole
dia.of the user end.
Torque ≤1Nm, the axial degree ≤0.2mm, the corner setover≤1.5°
Adapt to the encoder and user with the spring connect.
5+
less 10%
Model
DR4X6-D18L25
DR6.35X6.35-D18L25
DR8X8-D18L25
6.35mm (1/4") Shaft Coupler
Solid steel Shaft Coupler connects two axially aligned
shafts by hex drive set screws.
12.7mm dia
19mm long
6.35mm (1/4") bore
Internal
Dia 1
4
6. 35
8
Internal
Dia 2
6
6. 35
8
Price Each
IBE-004 Flexible Coupling DR4X6-D18L25
IBE-005 Flexible Coupling DR6.35X6.35-D18L25
External
Dia
18
18
18
1
$13.85
$13.85
Length
25
25
25
5+
less 10%
less 10%
IBEST BR series (Flexible Coupling)
Price Each
MOA-002 Shaft Coupler
1
$11.77
5+
less 10%
Aluminium Hub with Set Screws
Securely connect a gear or plate to a shaft using this
Aluminium Hub.
22.5mm dia
Connects to gear using 4 set screws
6.35mm (1/4") bore
Price Each
MOA-003 Aluminium Hub
1
$11.77
Model
5+
less 10%
Universal Aluminum Mounting Hub for 3mm Shaft Pair
These universal mounting hubs are designed to
work with most 3 mm shafts, including round shafts,
“D” shafts, and Tamiya’s 3 mm hexagonal shafts.
Each hub has four mounting holes for 2-56 screws,
letting you mount custom wheels or mechanisms to
your motors. 4-40 hex set screws (one included for each hub) allow
secure coupling of shaft to hub. The included set screws require a 0.05"
hex wrench (often the smallest size in SAE Allen wrench sets).
Price Each
MOA-010 Universal Mounting Hub for 3mm Shaft Pair
1
5+
$11.95 less10%
Universal Aluminum Mounting Hub for 4mm Shaft Pair
These universal mounting hubs are designed to
work with most 4 mm shafts, including round shafts,
and “D” shafts. Each hub has four mounting holes
for 4-40 screws, letting you mount custom wheels or
mechanisms to your motors. 4-40 hex set screws
(one included for each hub) allow secure coupling of
shaft to hub. The included set screws require a 0.05" hex wrench (often
the smallest size in SAE Allen wrench sets).
Price Each
MOA-011 Universal Mounting Hub for 4mm Shaft Pair
1
5+
$11.95 less10%
Pololu 37D mm Metal Gearmotor Bracket
These aluminum gearmotor brackets let
you securely mount Pololu 37D mm metal
gearmotors to your project. The brackets are sold
in pairs, and each bracket includes six M3 screws for
securing the motor to the bracket.
These light-weight brackets (under 15 g each) are specifically designed for the Pololu 37D mm metal gearmotors, such as the
19:1 metal gearmotor 37Dx52L mm. Each bracket features seven
mounting holes for M3 or #4-size screws along each edge, giving you a
variety of mounting options. A total of twelve M3 screws (six for each
bracket) are included for securing the motor to the bracket.
Price Each
MOA-014 Pololu 37D mm Metal Gearmotor Bracket Pair
Page 62 Ocean Controls Catalog 2009
D: External diameter of the connector; L: the
long of the connector.
M: The hole dia. of the encoder end. N: the hole
dia.of the user end.
Torque ≤1Nm, the axial degree ≤0.2mm, the
corner setover≤1.5°
Adapt to the encoder and user with the spring connect.
1
5+
$13.10 less10%
BR6.35X6.35-D24L25
BR8X8-D24L25
BR10X10-D30L30
Internal
Dia 1
6. 35
8
10
Internal
Dia 2
6. 35
8
10
Price Each
IBE-007 Flexible Coupling BR6.35X6.35-D24L25
External
Dia
24
24
30
1
$16.00
Length
25
25
30
5+
less 10%
Universal Aluminum Mounting Hub for 6mm
The universal aluminum mounting hub allows you to
mount custom wheels and mechanisms to 6 mm
motor shafts. The hubs are sold in pairs, and each
hub includes two 4-40 set screws for securing a
motor shaft to the hub. These universal mounting hubs are designed to
work with most 6 mm shafts, including round shafts and “D” shafts. Each
hub has six mounting holes for 4-40 screws, letting you mount custom
wheels or mechanisms to your motors. 4-40 hex set screws (two included for each hub) allow secure coupling of shaft to hub. The included
set screws require a 0.05" hex wrench (often the smallest size in SAE
Allen wrench sets).
Price Each
MOA-012 Universal Mounting Hub for 6mm Shaft Pair
1
5+
$12.95 less10%
Pololu 20D mm Metal Gearmotor Bracket
These aluminum gearmotor
brackets let you securely mount
Pololu’s 20D mm metal gearmotors to your
project. The brackets are sold in pairs, and each
bracket includes two M3 screws for securing the
motor to the bracket.
These light-weight brackets (under 5 g each) are
specifically designed for the Pololu 20D mm metal gearmotors, such as
the 25:1 metal gearmotor 20Dx44L mm. Each bracket features three
mounting holes and ten mounting slots for M3 or #4-size screws, giving
you a variety of mounting options. A total of four M3 screws (two for
each bracket) are included for securing the motor to the bracket.
Price Each
MOA-013 Pololu 20D mm Metal Gearmotor Bracket Pair
1
5+
$11.77 less10%
OCEAN CONTROLS - SOFTWARE
ModbusView Version 1.43
ModbusView is an easy to use program that monitors and simulates
Modbus communications on your PC. It enables your PC to act as
both a modbus master and a slave device making it easy for you to
simulate the action of your HMI machine, instruments, PLCs etc. ModbusView can operate on a PC under Windows 95/98, ME, NT, 2000,
XP and Vista. It can communicate both in the RTU form and the ASCII
form and it can also be set to a range of baud rates, data bits, parity
and stop bits.
The user can monitor and set the status of coils, input status, holding
registers and input registers. The values of the input and holding registers can be viewed in decimal, hexadecimal, long integer, long hexadecimals and floating point (forward and reverse)
Price Each
ModbusView
1
$59.00
ModbusView TCP Version 1.43
ModbusView TCP is an easy to use program that monitors and simulates Modbus TCP/IP communications on your PC. The Master (or
Client in Modbus TCP) establishes a connection with the Slave (or
Server). The Server waits for an incoming connection from the Client.
Once a connection is established, the Server then responds to the
queries from the Client until the client closes the connection It enables
your PC to act as both a modbus master and a slave device making it
easy for you to simulate the action of your HMI machine, instruments,
PLCs etc. ModbusView can operate on a PC under Windows 95/98,
ME, NT, 2000, XP and Vista (must have administrative rights). It communicates in the RTU The user can monitor and set the status of coils,
input status, holding registers and input registers. The values of the
input and holding registers can be viewed in decimal, hexadecimal,
long integer, long hexadecimals and floating point (forward and reverse)
Price Each
ModbusView
1
$59.00
ISEE Modbus
The ISEE-MODBUS data acquisition program is a fully featured minimum cost HMI program for controlling and monitoring controllers,
PLCs and instrumentation that use the modbus protocol. Running
under Windows XP/2000/NT/ME/98 it allows the user to
- Interrogate multiple controllers, PLCs and instruments
- Supports RTU and ASCII modes of Modbus
- View the holding and input registers. They can be viewed as raw
readings or in engineering units.
- Holding and Input registers can contain integers, long integers and
floating point numbers
- View the status of the coils and input status
- Write to the coils and holding registers
- Supports up to 1024 tags
- No graphics to draw. Simply display the readings on the screens.
Readings can be grouped as you like.
- Display registers, coils, statuses and calculated variables on graphs
or trends
Price Each
ISEE-modbus Software
Page 63 Ocean Controls Catalog 2009
1
$125.00
OCEAN CONTROLS - SOFTWARE
VIEW INTEGRA
The VIEW-INTEGRA data acquisition program is a fully featured minimum
cost HMI program for controlling and monitoring Crompton Instruments
Integra 1500 series of Digital Meters. Running under Windows XP/2000/
NT/ME/98 it allows the user to
- Interrogate up to 30 Digital Meters
- All Parameters are already defined ready to use
- View the value of parameters and units.
- Can reset Energy consumption values such as Total KWs
- Can define your own internal variables or tags for control and alarm
purposes
- No graphics to draw. Simply display the readings on the screens.
Readings can be grouped as you like.
- Display values of parameters and internal variables on graphs or
trends
- View the maximum and minimum values for each tag
- Log parameters and internal variables to a csv type file
- Display and analyse Historical logged files on graphs
- Define and display alarms
Price Each
1
ViewPID Software
ViewPID is our new easy to use Windows PC program that monitors and
records the performance of your PID controller (such as our Novus 1100,
1200, 2000 and 3000 controllers) The PC is simply connected to the PID
controller with a RS232 or RS485 connection. The software then communicates with the Process controller using Modbus Protocol.
By connecting your PC to your PID controller using a RS232 or RS485 serial
connection, ViewPID software interrogates your controller for the following
values using Modbus protocol
Process Variable, Setpoint, Output
Gain K, Integral Ki and Differential Kd
Features of ViewPID program
- A trend showing the process variable, setpoint and %output.
- Auto or fixed scaling on the trend
- Able to hold the trend.
- Able to change the period of polling from 1 to 1000 seconds
- A display of the setpoint, gain, integral and differential parameters
- Alter the setpoint, gain, integral and differential parameters from the display
- Log the the process variable, setpoint and %output to a csv file on your PC.
- Logged file can be opened later in Excel for analysis
Price Each
- Display a graph of your logged data.
ViewPID Software
Audio Wave Software V2
With AudioWave 2.0 your soundcard becomes a comfortable LF-signalgenerator, which produces signals from 1Hz to 20 kHz with a resolution of 1
Hz. Phase shift between left and right channel is adjustable from –180° to
+180° and an attenuator can be used for steps of 0dB, -3dB, -6dB, -10 dB, 20 dB, -30dB. Frequency, level and attenuation can be adjusted independently for left and right channel and optionally left and right channel can be
chained. AudioWave produces sine and noise signals, as well as modulated
signals. Automatic frequency and level progress is programmable. Complex
adjustment can be stored as presets with clear names.
Improvements with Version 2
Frequency adjustment 1Hz...20 kHz; 1 Hz resolution
Direct frequency input via keyboard
Soft frequency change
Independent or chained control of frequency, level and attenuation for left and right channel
Channel mute function
Duration up to 60 seconds for modulated signals
Price Each
AudioWave Software
Page 64 Ocean Controls Catalog 2009
1
$25.00
1
$50.00
OCEAN CONTROLS - RELAYS
12VDC or 24VDC PCB Relays
10A DPDT DIN Mount Relays
12VDC or 24VDC or 240VAC coil relay with two
changeover contacts (DPDT) rated at 10A
240VAC. Features LED Indicator. Coil at 12VDC
160ohms. Coil at 24VDC 650ohms. It is mounted
on a DIN Rail Mount base with screw Terminals.
Can be mounted by screws or on a Din Rail
Features built in LED Indicator
These SPDT relays from Goodsky are type
RWH-SH-112D 12V and RWH-SH-124D 24V
Can switch 10A at 240VAC and 24VDC.
Coil Resistance 400ohm 12VDC, 1600ohm
24VDC
Life expectancy
mechanical 10,000,000 operations at no load
electrical 100,000 at rated resistive load
Price Each
RLY-001 12V PCB Relay
RLY-002 24V PCB Relay
1
$2.50
$2.50
5+
less 10%
less 10%
Price Each
RLY-003 12VDC Relay and DIN Base
RLY-004 24VDC Relay and DIN Base
RLY-010 240VAC Relay and DIN Base
1
$11.91
$11.91
$11.91
5+
less 10%
less 10%
less 10%
10A 4PDT DIN Mount Relays
These relays feature both an LED and Press
to Test button
Relay SPDT 30A 12VDC Tag Connection
Specifications:
Specifications
Max Voltage 250VAC,110VDC
Max Current 10A (total)
Coil Resistance (24VDC) 350Ohm
Life expectancy
mechanical 10,000,000 operations no load
electrical 100,000 at rated resistive load
•
•
•
•
•
•
•
•
Available also in 24VAC coils
Price Each
RLY-005 4PDT DIN Mount Relay 24VDC
RLY-006 4PDT DIN Mount Relay 24VAC
1
$18.00
$18.00
5+
less 10%
less 10%
•
•
•
SDK4 12 VDC relay terminals coupled emission
SDK4 24 VDC relay terminals coupled emission
Price Each
RLY-018 12VDC Relay and DIN Base
Features:
Enter the input voltage: 12VDC±10%; 24 VDC±10%
Input current: About 13mA
Pull-in voltage: 75%Un max
Release voltage 5%Un min
Pull-in time: About 10ms
Release time: About 5ms
Additional input circuit: Red LED working status indication
Maximum switching voltage output: 250VAC,30VDC
Maximum switching current: 3A
Maximum switching power of the load resistor (cosφ = 1): 750VA/90W
The maximum movement frequency (negative rating): 1200 times / hour
Contact Material: Silver alloy
Contact Type: A regular open
Life (resistive load) Mechanical life: 2 × 10 7 switching action
Electrical life: 1 × 10 5 switching action
Test voltage winding / contact: 2kV, 50Hz, 1 minutes
Contact / Contact: 1kV, 50Hz, 1 minutes
Ambient temperature: -25℃…+40℃
Pollution level II
Connection: Screw connection
Conductor cross-sectional area: 0.5…2.5mm2
Dimensions: Width / thickness / height mm 66 / 6 (66/70)
Price Each
RLY-100 SDK4 12VDC relay terminals
RLY-110 SDK4 24VDC relay terminals
Page 65 Ocean Controls Catalog 2009
Max voltage:250V AC
Max current:30A
Max VA (Watts):7200VA (1100W)
Contact material: Silver Nickel Alloy
Coil resistance:160Ω
Max coil power:2.5W
Insulation resistance:>1000MΩ @ 500V DC
Dielectric strength (for 1 min):
1500V AC between open contact
2500V AC between coil & contact
Electrical life:100,000 operations
Mechanical life:1 million operations
Dimensions:˜50W x 27L x 20H mm (excluding terminals)
1
5+
$14.50
$14.50
less10%
less10%
1
$8.36
5+
less 10%
OCEAN CONTROLS - RELAYS
40A 240VAC Solid State Relay
40A 240VAC Solid State Relay
The SS-240DA solid state relay that offers 432VDC input control, with the output rated at
40Amps @ 240VAC. It provides 4000Vms
opto-isolation between input and output.
Comes with cover to minimize contact with
live voltages (see picture)
Input Circuit
- Control Voltage Range: 4- 32VDC
- Control Current: 6 to 10mA
- Pick Up voltage: 4V DC, Drop Out Voltage: 2VDC
Output Circuit
- Nominal Line Voltage: 240V AC
- Load Voltage Range: 24- 280V AC
- Min. Blocking Voltage: 600V AC
- Max one- cycle surge current: 400A
- Operating/Storage Temperature: -20 to 80degC/-40 to 100degC
- Dimensions:57(L) x 45(W) x30(H)mm
The SS-240AA Solid State Relay offers 80280VAC input control, with the output rated
at 40Amps @ 240VAC. It provides
4000Vms opto-isolation between input and
output. Comes with cover to minimize contact with live voltages (see picture)
Input Circuit
- Control Voltage Range: 80-280Vac
- Control Current: 10mA/110Vac
- Pick Up voltage: 60V AC, Drop Out Voltage: 40VAC
Output Circuit
- Nominal Line Voltage: 240V AC
- Load Voltage Range: 24- 280V AC
- Min. Blocking Voltage: 600V AC
- Max one- cycle surge current: 400A
- Operating/Storage Temperature: -20 to 80degC/-40 to 100degC
- Dimensions:57(L) x 45(W) x30(H)mm
Price Each
SSR-100 SS-240DA 4-32VDC Input 40A@240v AC Switch
Price Each
SSR-110 SS-240AA 80-280VAC Input 40A@240v AC Switch
1+
$35.00
40A 440VAC Solid State Relay
40A 440VAC Solid State Relay
The SS-440DA solid state relay that offers 432VDC input control, with the output rated at
40Amps @ 440VAC. It provides 4000Vms optoisolation between input and output. Comes with
cover to minimize contact with live voltages (see
picture)
Input Circuit
- Control Voltage Range: 4- 32VDC
- Control Current: 6 to 10mA
- Pick Up voltage: 4V DC, Drop Out Voltage: 2VDC
Output Circuit
- Nominal Line Voltage: 440V AC
- Load Voltage Range: 48– 440V AC
- Min. Blocking Voltage: 600V AC
- Max one- cycle surge current: 400A
- Operating/Storage Temperature: -20 to 80degC/-40 to 100degC
- Dimensions:57(L) x 45(W) x30(H)mm
Price Each
SSR-200 SS-440DA 4-32VDC Input 40A@240v AC Switch
1+
$42.50
10A 60VDC Solid State Relay
The SS-110DD Solid State Relay from
Conch is a panel mounting solid state relay
that offers 4-32VDC input control, with the
output rated at 10Amps @ 60VDC. It provides 4000Vms opto-isolation between input
and output. Comes with cover to minimize
contact with live voltages (see picture)
Input Circuit
- Control Voltage Range: 4-32Vdc
- Control Current: 6-10mA
- Pick Up voltage: 4V dc
- Drop Out Voltage: 2 V dc
Output Circuit
- Load Voltage Range: 5-60V DC
- Non rep. peak voltage: 150Vp
- Leakage current <1mA
- Operating/Storage Temperature: -20 to 80degC/-40 to 100degC
- Dimensions:57(L) x 45(W) x30(H)mm
Price Each
SSR-120 SS-240DD 4-32VDC Input 10A@60V DC Switch
Page 66 Ocean Controls Catalog 2009
1+
$35.00
1+
$35.00
The SS-440AA Solid State Relay from
Conch offers 80-280VAC input control, with
the output rated at 40Amps @ 480VAC. It
provides 4000Vms opto-isolation between
input and output. Comes with cover to minimize contact with live voltages (see picture)
Input Circuit
- Control Voltage Range: 80-280Vac
- Control Current: 10mA/110Vac
- Pick Up voltage: 60V AC, Drop Out Voltage: 40VAC
Output Circuit
- Nominal Line Voltage: 415V AC
- Load Voltage Range: 48-480V AC
- Min. Blocking Voltage: 600V AC
- Max one- cycle surge current: 400A
- Operating/Storage Temperature: -20 to 80degC/-40 to 100degC
- Dimensions:57(L) x 45(W) x30(H)mm
Price Each
SSR-205 SS-440AA 80-280VAC Input 40A@240v AC Switch
1+
$47.50
OCEAN CONTROLS - RELAY CARDS
40A 240VAC Solid State Relay Potentiometer Input
The SS-240VA is a panel mounting solid
state relay that allows a 500KOhm pot to be
connected across the input. The position of
the potentiometer results in Phase Trigger
Control of the Load. If the potentiometer is
set at 10% then 10% of each half cycle is
passed. (Warning there is no isolation
between the input and output. There is
240VAC across the potentiometer inputs.
The potentiometer must be rated to
240VAC) The breakdown voltage is rated
at 2500Vrms. Comes with cover to minimize contact with live voltages
Specifications:
Input Circuit
- Potentiometer Resistor 500KOhm for 240VAC
Output Circuit
- Load Voltage Range: 80-280V AC
- rated at 40Amps @ 240VAC.
- Non rep. peak voltage: 600Vp
- Leakage current 8mA
- 1 Cycle Surge Current 400A
Price Each
SSR-125 SS-240VA 500K Pot Input 40A@240V AC Switch
1+
$35.00
This PCB mounting, single in line package relay capable of switching up
to 240V AC at 3 amps.
Input Circuit
- Control Voltage Range: 3- 32VDC
- Control Current: 15mA Max- Min. turn off voltage: 1V DC
- Input Resistance: 2.2kohm min.
Output Circuit
- Max load current: 3A
- Nominal Line Voltage: 240V AC
- Load Voltage Range: 24- 280V AC
- Min. Blocking Voltage: 600V AC
- Max one- cycle surge current: 80A
- Min. Load current: 50mA
- Dimensions:10(D) x 42(W) x25(H)mm
1+
$16.32
100A DC Solid State Relay
Solid State Relay 3-32VDC Input 100A@30VDC Switching
This solid state relay uses MOSFET technology to provide an economical and reliable method of switching medium to high power DC loads. By
electrical switching with a
Output Circuit
- Load Voltage: 0-30VDC
- Load Current: 0.02-100A
- Max On-State Resistance: 0.007Ohms
- Max On-State Voltage Drop: 0.35V
- Max Turn On Time: 0.5ms
- Max Turn Off Time: 0.5ms
- Max Surge Current: 240A (10ms)
Input Circuit
- Control Voltage: 3-32VDC
- Control Current: 28mA max.
- Min Turn Off Voltage: 1.0VDC
- Input Resistance: 1.2kOhm .
Dimensions: 58.4(L) x 45.7(W) x 22.9(D)mm
Price Each
SSR-013 Solid State Relay 100A@30v DC Switching
Page 67 Ocean Controls Catalog 2009
The SS-240CA is a panel mounting solid state
relay that allows a 4-20mA signal to be connected across the input. The level of the 4-20mA
signal results in Phase Trigger Control of the
Load. A curve is provided on the datasheet
showing the relationship between the input current and the Output Percentage load. The load
output is rated at 40Amps @ 240VAC. It provides 4000Vms opto-isolation between input and
output. A cover to minimize contact with live
voltages is included
Specifications:
Input Circuit
- Input Control Range 4-20mA
Output Circuit
- Load Voltage Range: 90-260V AC
- Non rep. peak voltage: 600Vp
- Leakage current 8mA
- 1 Cycle Surge Current 400A
- Operating/Storage Temperature: -20 to 80degC/-40 to 100degC
- Dimensions:57(L) x 45(W) x30(H)mm
- DIN Rail Mount Heat Sink included.
Price Each
SSR-130 SS-240CA 4-20mA Input 40A@240V AC Switch
PCB Solid State Relays
Price Each
SSR-011 32V DC Solid State Relay
40A 240VAC Solid State Relay with 4-20mA Input
1+
$43.59
1+
$75.00
Solid State Relay Heatsink
These heatsinks are designed for mounting the 40A 240VAC and SSR-013 solid
state relays on them. They are manufactured from solid black aluminium and
come in lengths of 50mm (fits 1 relay) and
100mm (fits 2 Solid State Relays). The
screw holes for the solid state relays are
4mm.
The heatsinks are suitable to be used with
an 80mm fan mounted at the heatsink end. .
Price Each
SSR-020 Black Aluminium Heatsink 50mm for SSR
SSR-021 Black Aluminium Heatsink 100mm for SSR
1
$15.00
$22.00
5+
less 10%
less 10%
OCEAN CONTROLS - RELAY CARDS
NIO - Relay Interface
DIN Rail Mounted Heatsink
The NIO series of DIN rail relays are interfaces used extensively in switching applications in industrial automation. They are built with high quality components for
beyond normal performance and comply with the highly demanding automation
standards.
Electrical connections are quickly performed through the quick-on spring loaded
terminals without turning screws which help speed up the installation procedure
and guarantee highly efficient contacts under high amperage.
Specifications:
* Mechanical life: 10,000,000 cycles
* Electrical life with resistive load: 60,000 cycles
* Switching time: 5 ms
* Electrical insulation between input and output: 1000 Vac
* Operating temperature: -40 to 70 °C (-40 to 158 °F)
* Enclosure protection: IP20
* Wiring gauge: 0.2 ~ 1.5 mm²
* Input
Switching rated voltage (UN): 12/24/220 Vac/dc
Consumption: 0.2/0.3/0.9 VA (W)
Holding voltage: 0.8 ... 1.1 UN
Must drop-out voltage: 0.6 UN
* Output
Output type: SPDT relay
Rated current: 6 A
Maximum instantaneous current: 10 A
Working voltage: 250 Vac/dc
Maximum working voltage: 400 Vac/dc
Resistive load capacity: 1500 VA
Inductive load capacity: 300 VA
Capacity with monophase motor (220 Vac): 185 VA (1/4 HP)
Maximum resistive current DC (30V / 220 V): 6 A / 0,15 A
Contact material: AgNi
* OPTIONS
Identification and interconnecting acessories
Price Each
SSR-040 NIO - Relay Interface
1
Price Each
SSR-030 DIN Rail Aluminium Heatsink 40mm High
SSR-031 DIN Rail Aluminium Heatsink 60mm High
1
$27.50
$29.50
5+
less 10%
less 10%
ALT-301 1 PHASE SCR POWER REGULATOR
Features:
*Down-Opened panel, easy
for fuse replacement
*Automatic power frequency detection for 50~60 Hz
*Adjustment VR for 0~100% output
*DIN rail type, easy installation
5+
AC Zero Crossing Solid State Relays Card
These would have to be the most versatile relay cards on the
market. Each relay can be operated by TTL levels, NPN and PNP
open collector or 0 to 12V. Each relay has two inputs, marked LO and HI.
As the names suggest a low on the LO input will operate the relay. Similarly a high
on the HI input will also operate the
relay.
Specifications:
Operating Voltage 12VDC
Input low voltage (LO) 0 - 0.8V
Input high voltage (HI) 2.4 - 12V
We have operated these relays from
an old style TTL 7404 Hex Inverter
which have less drive capacity than the newer HC and HCT types. The inverter
could operate the relay with both a low and a high output signal. But what is more
important was that the High voltage dropped from 4V to 3.5V showing the output
still had capacity to drive other TTL devices
Low profile PCB mounting solid state relays with LED input status indication. Suitable for applications such as I/O interfaces and programmable logic controllers.
SY-4096
Type: Zero crossing turn on, solid state relay. The relay will only turn on when the
line (output) voltage is near zero. Suitable for resistive loads.
Control voltage range: 9.6 - 14.4VDC
Load voltage: 75 - 400VAC
Load current: 0.1 - 3A
A LED shows the state of each relay.
The Relay Cards are available in 12VDC
Four 3.5mm holes in each corner allow easy mounting on a panel
Dimensions of card
2 relay card - 42(L) x 71(W) x 20(H)mm
4 relay card - 86(L) x 71(W) x 20(H)mm
6 relay card - 130(L) x 71(W) x 20(H)mm
8 relay card - 174(L) x 71(W) x 20(H)mm
Price Each
POC-122 Two 12 V AC Zero Crossing Solid State Relays Card
POC-124 Four 12 V AC Zero Crossing Solid State Relays Card
POC-128 Eight 12 V AC Zero Crossing Solid State Relays Card
POD-122 Two 12 V AC Zero Crossing Solid State Relays Card on DIN Rail
POD-124 Four 12 V AC Zero Crossing Solid State Relays Card on DIN Rail
POD-128 Eight 12 V AC Zero Crossing Solid State Relays Card on DIN Rail
Page 68 Ocean Controls Catalog 2009
These heatsinks are designed for mounting the 40A 250VAC
and SSR-013 solid state relays on them. They are manufactured from solid aluminium and come in height of 40mm and
60mm and a length of 100mm (fits 1 relay). The screw holes for
the solid state relays are 4mm.
The heatsinks are suitable to be used with an 80mm fan
mounted at the heatsink end.
Specifications:
* Input Voltage: AC 220~380V / AC 480V +- 15%
* Load Current: 50A
* Input Signal: 4~20 mAdc
* Adjustment VR: 0~100%
* LED Indication: Green: Power Indicator;
Green: Input Indicator;
Red: Output Indicator;
Yellow: Error Indicator
* Temperature Coefficient: 100ppm / °C (0~60 °C)
* Operating Temperature: 0~50 C
* Operating Humidity: 20~90% RH (non-condensing)
* Storage Temperature: 0~60 C
* Storage Humidity: 20~90% RH (non-condensing)
* Power Supply: AC 220V +-15%
Price Each
ALT-301 1 PHASE SCR POWER REGULATOR
1
$191.44
5+
less 10%
Multiple Relay Cards
These would have to be the most versatile relay cards on the market. The cards
come in a 12V or 24V powered form.
Each relay can be operated by TTL levels, NPN and PNP open collector or 0 to
12V (0 to 24V if using 24VDC relays). Each relay has two inputs, marked LO and
HI. As the names suggest a low on the LO input will operate the relay. Similarly a
high on the HI input will also operate the relay. They also feature LEDs to indicate
the state of the relay.
Specifications:
Operating Voltage 12VDC (or
24VDC)
Input low voltage (LO) 0 - 0.8V
Input high voltage (HI) 2.4 - 12V
(or 24VDC)
They are available in 2, 4, 6 and
8 Relays cards
Price Each
RLC-122 Two 12V Relay Card
RLC-124 Four 12V Relay Card
RLC-128 Eight 12V Relay Card
RLC-242 Two 24V Relay Card
RLC-244 Four 24V Relay Card
RLC-248 Eight 24V Relay Card
1
$37.50
$74.50
$149.00
$56.00
$107.00
$214.00
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
1
$21.50
$42.50
$85.00
$21.50
$42.50
$85.00
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - RELAY CARDS
Multiple Relay Cards DIN Rail Mounted
Telecoms Relays Card
These would have to be the most versatile relay cards on the market. The cards
come in a 12V or 24V powered form.
Each relay can be operated by TTL levels, NPN and PNP open collector or 0 to
12V (0 to 24V if using 24VDC relays). Each relay has two inputs, marked LO and
HI. As the names suggest a low on the LO input will operate the relay. Similarly a
high on the HI input will also operate the relay. They
also feature LEDs to indicate the state of the relay.
Specifications:
Operating Voltage 12VDC (or 24VDC)
Input low voltage (LO) 0 - 0.8V
Input high voltage (HI) 2.4 - 12V (or 24VDC)
They are available in 2, 4, 6 and 8 Relays configurations mounted in a DIN rail carrier
Price Each
RLD-122 Two 12V Relay Card on DIN Rail
RLD-124 Four 12V Relay Card on DIN Rail
RLD-128 Eight 12V Relay Card on DIN Rail
RLD-242 Two 24V Relay Card on DIN Rail
RLD-244 Four 24V Relay Card on DIN Rail
RLD-248 Eight 24V Relay Card on DIN Rail
1
$40.00
$75.00
$150.00
$40.00
$75.00
$150.00
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
Plug-In Relays Card
These would have to be the most versatile relay cards on the
market. Each relay can be operated by TTL levels, NPN and PNP
open collector or 0 to 12V(0 to 24V if using 24VDC relays). Each relay
has two inputs, marked LO and HI. As the names suggest a low on the LO input
will operate the relay. Similarly a high on the HI input will also operate the relay.
Specifications:
Operating Voltage 12VDC (or 24VDC)
Input low voltage (LO) 0 - 0.8V
Input high voltage (HI) 2.4 - 12V (or 24VDC)
We have operated these relays from an old style TTL 7404 Hex Inverter which
have less drive capacity than the newer HC and HCT types. The inverter could
operate the relay with both a low and a high output signal. But what is more important was that the High voltage dropped from 4V to 3.5V showing the output still had
capacity to drive other TTL devices
Fully sealed construction (immersion cleanable).
Specifications
Max voltage: 250V AC, 110V DC
Max current: 16A
Max VA (Watts): 1800VA (450W)
Contact material: Silver Selenium Dioxide
Coil resistance: 200Ω
Max coil power: 720mw
Insulation resistance: >100MΩ@ 500V DC
Dielectric strength (for 1 min):
1000V AC between open contacts
5000V AC between coil & contact
Electrical life: 100,000 operations
Mechanical life: 10 million operations
Dimensions: 13W x 29L x 21H mm
Page 69 Ocean Controls Catalog 2009
Specifications:
Operating Voltage 12VDC
Input low voltage (LO) 0 - 0.8V
Input high voltage (HI) 2.4 - 12V
We have operated these relays from
an old style TTL 7404 Hex Inverter
which have less drive capacity than the newer HC and HCT types. The inverter
could operate the relay with both a low and a high output signal. But what is more
important was that the High voltage dropped from 4V to 3.5V showing the output
still had capacity to drive other TTL devices
Elegant relays. PCB mounting featuring silver alloy contacts SPDT- 12V DC. - Coil
285 ohms. - 10A @ 30V DC or 10A @ 240V AC contact rating.
A LED shows the state of each relay.
The Relay Cards are available in 12VDC
Four 3.5mm holes in each corner allow easy mounting on a panel
Dimensions of card
2 relay card - 42(L) x 71(W) x 20(H)mm
4 relay card - 86(L) x 71(W) x 20(H)mm
6 relay card - 130(L) x 71(W) x 20(H)mm
8 relay card - 174(L) x 71(W) x 20(H)mm
Price Each
1
PMC-122 Two 12 V Telecoms Relays Card
$26.40
PMC-124 Four 12 V Telecoms Relays Card
$52.30
PMC-128 Eight 12 V Telecoms Relays Card
$104.60
PMD-122 Two 12 V Telecoms Relays Card on DIN Rail $44.90
PMD-124 Four 12 V Telecoms Relays Card on DIN Rail $84.80
PMD-128 Eight 12 V Telecoms Relays Card on DIN Rail $169.60
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
DC Solid State Relays Card
These would have to be the most versatile relay cards on the
market. Each relay can be operated by TTL levels, NPN and
PNP open collector or 0 to 12V. Each relay has two inputs, marked
LO and HI. As the names suggest a low on the LO input will operate the
relay. Similarly a high on the HI input will also operate the relay.
Specifications:
Operating Voltage 12VDC
Input low voltage (LO) 0 - 0.8V
Input high voltage (HI) 2.4 - 12V
We have operated these relays from an old style TTL 7404 Hex Inverter which
have less drive capacity than the newer HC and HCT types. The inverter could
operate the relay with both a low and a high output signal. But what is more important was that the High voltage dropped from 4V to 3.5V showing the output still had
capacity to drive other TTL devices
Low profile PCB mounting solid state relays with LED input status indication. Suitable for applications such as I/O interfaces and programmable logic controllers.
SY-4093
Control voltage range:9.6 14.4VDC
Max. input current: 20mA
Load voltage: 3 - 125VDC
Load current: 0.01 - 2A
A LED shows the state of each relay.
The Relay Cards are available in
12VDC or 24VDC
Four 3.5mm holes in each corner allow easy mounting on a panel
Dimensions of card
2 relay card - 42(L) x 71(W) x 20(H)mm
4 relay card - 86(L) x 71(W) x 20(H)mm
6 relay card - 130(L) x 71(W) x 20(H)mm
8 relay card - 174(L) x 71(W) x 20(H)mm
Price Each
PPC-122 Two 12 V Plug-In Relays Card
PPC-124 Four 12 V Plug-In Relays Card
PPC-128 Eight 12 V Plug-In Relays Card
PPD-122 Two 12 V Plug-In Relays Card on DIN Rail
PPD-124 Four 12 V Plug-In Relays Card on DIN Rail
PPD-128 Eight 12 V Plug-In Relays Card on DIN Rail
PPC-242 Two 24 V Plug-In Relays Card
PPC-244 Four 24 V Plug-In Relays Card
PPC-248 Eight 24 V Plug-In Relays Card
PPD-242 Two 24 V Plug-In Relays Card on DIN Rail
PPD-244 Four 24 V Plug-In Relays Card on DIN Rail
PPD-248 Eight 24 V Plug-In Relays Card on DIN Rail
These would have to be the most versatile relay cards on the
market. Each relay can be operated by TTL levels, NPN and PNP
open collector or 0 to 12V. Each relay has two inputs, marked LO and HI. As
the names suggest a low on the LO input will operate the relay. Similarly a high on
the HI input will also operate the
relay.
1
$22.90
$45.30
$90.60
$41.40
$77.80
$155.60
$22.90
$45.30
$90.60
$41.40
$77.80
$155.60
5+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
A LED shows the state of each
relay.
The Relay Cards are available in 12VDC
Four 3.5mm holes in each corner allow easy mounting on a panel
Dimensions of card
2 relay card - 42(L) x 71(W) x 20(H)mm
4 relay card - 86(L) x 71(W) x 20(H)mm
6 relay card - 130(L) x 71(W) x 20(H)mm
Price Each
1
5+
PNC-122 Two 12 V DC Solid State Relays Card
$35.10 less10%
PNC-124 Four 12 V DC Solid State Relays Card
$69.70 less10%
PNC-128 Eight 12 V DC Solid State Relays Card
$139.40 less10%
PND-122 Two 12 V DC Solid State Relays Card on DIN Rail $53.60 less10%
PND-124 Four 12 V DC Solid State Relays Card on DIN Rail $102.20 less10%
PND-128 Eight 12 V DC Solid State Relays Card on DIN Rail$204.40 less10%
OCEAN CONTROLS - FANS
60mm 12v DC - 2 Wire Sleeve Bearing
FAN-002 80mm 12VDC FAN Sleeve Bearing
- Air Volume 0.57 (M3/min), 20 (CFM)
- Bearing System Sleeve
- Noise 30dB (A)
- Speed 4,000 rpm
- Input 1.6 watts
- Current 130mA
- Size 60 x 60 x 25.4mm
- Flylead connection
- Impeller Plastic, fibreglass filled
- Housing Plastic, fibreglass filled.
Price Each
FAN-001 60mm 12VDC - 2 Wire Sleeve Bearing
- Air Volume 0.97 (M3/min), 34 (CFM)
- Bearing System Sleeve
- Noise 32dB (A)
- Speed 3,000 rpm
- Input 2.4 watts
- Current 200mA
- Size 80 x 80 x 25.4mm
- Flylead connection
- Impeller Plastic, fibreglass filled
- Housing Plastic, fibreglass filled
1
$17.55
5+
less 10%
FAN-003 80mm 12VDC Ball Bearing Fan
1
$19.77
5+
less 10%
Price Each
FAN-004 120mm 12v DC - 2 Wire Thin Ball Bearing
1
$30.23
5+
less 10%
FAN-006 80mm 24VDC Ball Bearing Fan
Air volume: 1.13 (m3/min) 40(CFM)
Noise: 35 dBAInput: 3.12 Watts
Size: 80 x 80 x 25.4mm
Impeller: Plastic, fibreglass filled
Housing: Plastic, fibreglass filled
Bearing system: Sleeve
Speed: 3,200 rpm
Current: 130 mA
Flylead connection
Life expectancy 100,000 hours @ 25°C.
Air volume: 1.13 (m3/min) 40(cfm)
Noise: 35 dBAInput: 3.12 Watts
Size: 80 x 80 x 25.4mmImpeller: Plastic, fibre glass filled
Housing: Plastic, fibre glass filled
Bearing system : Ball Bearing
Speed: 3,200 rpm
Current: 130 mA
Flylead connection
Price Each
FAN-006 80mm 24v DC - Ball Bearing Fan
Page 70 Ocean Controls Catalog 2009
5+
less 10%
- Air volume 2.3 (m3/min) 80(CFM)
- Flylead connection.
- Noise 42 dB (A)
- Speed 3,000 rpm
- Input 4.56 Watts
- Current 380 mA
- Size 120 x 120 x 25.4mm
- Voltage 12VDC
- Impeller Plastic, fibreglass filled
- Housing Plastic, fibreglass filled
- Bearing system Ball race.
FAN-005 80mm 24VDC Sleeve Bearing Fan
Price Each
FAN-005 80mm 24v DC - 2 Wire Thin
1
$17.55
FAN-004 120mm 12VDC Ball Bearing Fan
Life expectancy 100,000 hours @ 25°C.
- Air Volume 0.97 (M3/min), 34 (CFM)
- Noise 32dB (A)
- Speed 3,000 rpm
- Input 2.4 watts
- Current 200mA
- Size 80 x 80 x 25.4mm
- Flylead connection
- Impeller Plastic, fibreglass filled
- Housing Plastic, fibreglass filled.
Price Each
FAN-003 80mm 12v DC - 2 Wire Ball Bearing
Price Each
FAN-002 80mm 12v DC - 2 Wire Sleeve Bearing
1
$17.55
5+
less 10%
1
$21.95
5+
less 10%
OCEAN CONTROLS - PLC’S
XC3 Series of PLC
The XC3 series from Rockhood Automation features a large number of functions, large memory capacity, small size and fast scan times
Although economically priced, these PLC's have been built and designed with motion control in mind.
Basic features in the XC series programmable logic controller are
• Max 1024 I/O points using expansion modules.
• Program's capacity is 30K
• Two high speed counter inputs, the highest frequency is 200K.
• 2 pulse outputs for stepper or servo motor control the max pulse output is 400K
• PWM Control
• support for CAN bus, Modbus and TCP/IP Ethernet.
Other features include
• Free Software
• Programmable in Ladder Logic and Instruction List
Can be used with our HMI Displays (OP-320A, MY-330, TP-562T etc )on the next page
The software is fast and easy to use. It allows for commenting of the variables so the rungs are easy to understand.
It has an online monitor which allows the user to monitor the program on the ladder or open the data window to modify or monitor the data variables
The XCP software also features a rich instruction list which allow calculations in integer, long integer or floating point. Other instructions include ordinal
control, data manipulation, interrupts, communications and motion control.
Copy, cut and paste of instruction and ladder programming allows easy editing of programs
Model
Digital Transistor
Relay
Power
Notes
Inputs Outputs
Outputs
XC3-14RT-C
XC3-14RT-E
XC3-32T-C
XC3-32T-E
XC5-48T-C
8
8
18
18
28
2
2
14
14
20
4
4
0
0
0
20-30VDC
90-260VAC
20-30VDC 2 High Speed Pulse Outputs
90-260VAC 2 High Speed Pulse Outputs
20-30VDC
4 High Speed Pulse Outputs
Price Each
PLC-001 XC3-14RT-E
PLC-002 XC3-14RT-C
PLC-021 XC3-32T-C
PLC-022 XC3-32T-C
PLC-060 XC5-48T-C
1
$215.00
$215.00
$349.00
$349.00
$525.00
XC3-19AR PLC
The XC3-19AR from Rockhood is a PLC with the following features all in one unit
Basic Performance
- Integrates logic Control, analog input/output in one unit
- Digital Input - 9 points (NPN type optical coupling insulation)
- Digital Output - 10 points (Relay Type)
- Analog Input - 8 points (0 to 10 voltage)
- Analog Output - 2 points (0 to 10 voltage or 4 to 20mA)
- Supports 3 channels AB phase input
- Supports 4 channels high speed count (20KHzs)
- All connections via screw terminals
- High performance-price ratio,major space saving
Price Each
1
Other features include
PLC-100 XMP3-18R-C
$425.00
• Free Software
PLC-301 OP-XP-CAB Programming Cable
$26.00
• Programmable in Ladder Logic and Instruction List
The software is fast and easy to use. It allows for commenting of the variables so the rungs are easy to understand.
It has an online monitor which allows the user to monitor the program on the ladder or open the data window to modify or monitor the data variables
The XCP software also features a rich instruction list which allow calculations in integer, long integer or floating point. Other instructions include ordinal
control, data manipulation, interrupts, communications and motion control.
Copy, cut and paste of instruction and ladder programming allows easy editing of programs
XMP3 DUAL PUMP CONTROLLER
We have programmed our XMP3 PLC to be a Dual Pump Controller. It is suitable
for both water and wastewater applications. It can be used to control the pumps for
filling a tank or emptying a wet well. The units comes with the usual features found
with pump controllers and more. The controller features
• 1 or 2 pump control.
• pumps can operate in duty/standby or cyclic.
• Can control pumps to fill a tank or empty a well
• Operates with conductive probe, pressure, ultrasonic or any 4-20mA device
• Start pumps by Level sensor, high or low floats or both
• With level sensor operation each pump can have its own start and stop levels
• Switch over to standby pump on overload, runtime fail or no flow fault.
• Times to recognize faults are configurable.
• Can operate a wet well washer
• Start a pump once a day to take advantage of Off Peak Electricity tariffs
• Start a pump after a period of no activity. Useful to prevent wet wells going septic
• Easily configured with the touch screen.
Price Each
• Modbus connection to connect to another PLC or RTU.
PLC-400 XMP3 Pump Controller
Page 71 Ocean Controls Catalog 2009
1
$575.00
OCEAN CONTROLS - PLC’S
XC3 Series Expansion Modules
The XC3 Programmable Logic Controllers can be expanded with these Analog modules and I/O modules.
Analog Modules
Description
XC-4AD2DA
4 Analog In 2 Analog Out Module
XC-4AD
4 Analog In Module
XC-8AD
8 Analog In Module
XC-2DA
2 Analog Out Module
XC-4DA
4 Analog Out Module
XC-4PT4AD
4 Analog In Module 4 PT100 temperature sampling
XC-6PT
6 PT100 temperature sampling Module, 0-300 C, precision:
0.2 degree
XC-6PT-P
6 PT100 temperature sampling PID Out Module, 0-300 C,
precision: 0.2 degree, PID output
XC-6TC
6 K, E temperature sampling Module, 0-1200 C, precision:
0.5 degree,
XC-6TC-P
6 K, E temperature sampling PID Control Module, 0-1200
C, precision: 0.5 degree, PID control
XC-2AD2PT-BD
2 CHANNELS 12Bits analog input, 2 channels Pt100 temperature sampling card (XC3-14 models don`t support)
XC3-COM-BD
RS232, RS485 communication expand board (XC3-14
models don`t support)
I/O Modules
Description
XC3-E8X
8 points DC input
XC3-E8YR
8 points relay output
XC3-E8YT
8 points transistor output
XC3-E16X
16 points DC input
XC3-E16YR
16 points relay output
XC3-E16YT
16 points transistor output
XC3-E32X
32 points DC input
XC3-E32YR
32 points relay output
XC3-E32YT
32 points transistor output
XC3-E8X8YR
8 points DC input / 8 points relay output
XC3-E8X8YT
8 points DC input / 8 points transistor output
Price Each
1
PLC-200 XC-4AD2DA 4 Analog In 2 Analog Out Module
$349.00
PLC-201 XC-4AD 4 Analog In Module
$289.00
PLC-202 XC-8AD 8 Analog In Module
$330.00
PLC-203 XC-2DA 2 Analog Out Module
$269.00
PLC-204 XC-4DA 4 Analog Out Module
$289.00
PLC-205 XC-4PT4AD 4 Analog In / PT100 temperature
$359.00
PLC-206 XC-6PT 6 PT100 temperature Module
$330.00
PLC-207 XC-6PT-P 6 PT100 temperature & PID Out Module
$369.00
PLC-208 XC-6TC 6 K, E temperature Module
$330.00
PLC-209 XC-6TC-P 6 K, E temperature & PID Control Module
$369.00
PLC-210 XC-2AD2PT-BD 2 Analog In & PT100 temperature Module $180.00
PLC-211 XC3-COM-BD RS232, RS485 communication expand board $141.00
PLC- 232 XC3-E8X 8 I/O Expansion module
PLC- 233 XC3-E8YR 8 I/O Expansion module
PLC- 234 XC3-E8YT 8 I/O Expansion module
PLC- 235 XC3-E16X 16 I/O Expansion module
PLC- 236 XC3-E16YR 16 I/O Expansion module
PLC- 237 XC3-E16YT16 I/O Expansion module
PLC- 238 XC3-E32X 32 I/O Expansion module
PLC- 239 XC3-E32YR 32 I/O Expansion module
PLC- 240 XC3-E32YT 32 I/O Expansion module
PLC- 241 XC3-E8X8YR 8 I/O Expansion module
PLC- 242 XC3-E8X8YT 8 I/O Expansion module
$117.00
$122.00
$139.00
$141.00
$151.00
$151.00
$245.00
$269.00
$269.00
$151.00
$151.00
XC5 Series of PLC
The XC5 series from Rockhood Automation features a large number of functions, large memory capacity, small size and fast scan times
Although economically priced, these PLC's have been built and designed with motion control in mind.
Basic features in the XC series programmable logic controller are
• Max 1024 I/O points using expansion modules.
• Program's capacity is 30K
• Two high speed counter inputs, the highest frequency is 200K.
• 4 pulse outputs for stepper or servo motor control the max pulse output is 400K
• PWM Control
• support for CAN bus, Modbus and TCP/IP Ethernet.
Other features include
• Free Software
• Programmable in Ladder Logic and Instruction List
Can be used with our HMI Displays (OP-320A, MY-330, TP-562T etc )on the next page
The software is fast and easy to use. It allows for commenting of the variables so the rungs are easy to understand.
It has an online monitor which allows the user to monitor the program on the ladder or open the data window to modify or monitor the data variables
The XCP software also features a rich instruction list which allow calculations in integer, long integer or floating point. Other instructions include ordinal
control, data manipulation, interrupts, communications and motion control.
Copy, cut and paste of instruction and ladder programming allows easy editing of programs
Model
Digital Transistor
Relay
Power
Notes
Price Each
1
Inputs Outputs
Outputs
PLC-060 XC5-48T-C
$595.00
XC5-48T-C
28
20
0
20-30VDC
4 High Speed Pulse Outputs
Page 72 Ocean Controls Catalog 2009
OCEAN CONTROLS - PLC OPERATOR PANELS
OP-320A
MP330
This low cost display features
- 3.7 inch monochrome LCD screen
- 192 x 64 Pixels
- easily connects to our XC3 and XC5
PLC's
The 20 keys can be defined to be function keys (In which 12 keys can be defined to be number keys and other usage), STN LCD display with back light, can display 24 letters*4 lines
General Specifications:
• Screen Pixel: 192 × 64
• Display Size: 3. 7” LCD
• User Memory: 1MB Flash, 1KB SRAM
• Expected Bulb Life: 20,000 Hours
• Function Keys: 10 Numeric Keys: 10
• Color: STN LCD with Backlight
• Screen Saver: Set by Software, Display Brightness: 60 nits
• Communication Port: RS 232 / RS 485
• Real Time Clock: Yes
• Power Input: 24VDC 4W
• Operation Temperature: 0ºC ~ 50ºC
• Storage Temperature: -10ºC ~ 60ºC
• Weight: 0.45Kg
• Relative Humidity: 20 ~ 85% non-condensing
• IP 65F
A low cost versatile display. Its features
include
- 3.7-inch, Monochrome Display area
320*240
- 26 function keys, support area
- Numerical Keypad for data entry
- Suitable for various PLC's including
our XC3 and XC5 series
- Password protection and internal clock(Optional)
- Key-press can be defined as function keys, partly replace the mechanical keys in your control cabinet.
- With backlight STN LCD
- Using life Up to 20000hrs Ambient temperature 25degC 24 hours
operation
- Supply Voltage Range DC22V~DC26V
- Supply Current <260mA
- Brightness Can not be adjusted
- Character Size English 8*16 16*32
- Memory Screen 4MB FlashROM
- Memory Data 2KB SRAM
- Interface Download Port RS232
- COM Port RS232 /RS422
Other features include
• Free Software
Other features include
• Free Software
Price Each
HMI-001 OP320-A Text Display
1
$249.00
Price Each
HMI-010 MP330 Text Display
1
$299.00
TPA61-T Touch Screen Display
TP562-T Touch Screen Display
5.7 inch 256 color TFT 320*240 pixels
4MB FlashROM 4KB SRAM
With data display , data monitor, alarm,
scheme and relevant functions
Support for various popular PLC's and has
double separated communication ports
Easily connects to our XC3 and XC5 PLC's
Its own screen edit software supports simulate offline and simulate online as well as configuration function.
General Specifications:
• Screen Pixels: 320 × 240
• Display Size: 5.7” diagonal TFT color LCD
• Touch Type: Resistive Touch Screen
• User Memory: 4MB Flash, 2KB SRAM
• Expected Bulb Life: 50,000 Hours
• Touch Cells: 192 (16 X 12)
• Color: 256 True TFT Color
• Screen Saver: Set by software
• Display Brightness: 300 nits
• Communication Ports: RS-232, RS 422 / 485
• Protocols: ASCII and Modbus RTU
• Real Time Clock: Yes
• Power Input: 24 VDC
• Power Consumption: 7.5 W
• Operation Temperature: 0ºC ~ 50ºC
• Storage Temperature: -10ºC ~ 60ºC
• Relative Humidity: 20 ~ 85% non-condensing
• IP 65F
A 10.4 Inch 800x600pixel touchscreen
which features:
• General specifications:
• Screen pixels: 800 x 600
• Display size: 10.4in, true TFT color
LCD
• Touch type: resistive touch screen
• User memory: 8MB flash, 4KB SRAM
• Expected bulb life: up to 50,000 hours
• Touch cells: 768 (32 X 24)
• Color: 256 true TFT color
• Screen saver: set by Software
• Display brightness: 400nits
• Communication ports: RS-232, RS-422/485, two USB ports
• Protocols: Include ASCII and Modbus RTU
• Real time clock: yes
• Power input: 24 VDC
• Power consumption: 10W
• Operation temperature: 0-50 degree Celsius
• Storage temperature: -10-60 Degree Celsius
• Withstand voltages: AC1000V-20mA within one minute
• Noise resistance: 1,000Vp-p noise voltage
• Weight: 4lbs
• Relative Humidity: 2-85% non-condensing
• IP: 65F
Other features include
• Free Software
Other features include
• Free Software
Price Each
HMI-020 TP562-T 5.7 inch Touchscreen
Page 73 Ocean Controls Catalog 2009
1
$799.00
Price Each
HMI-030 TPA61-T 10 inch Touchscreen
1
$1699.00
OCEAN CONTROLS - PLC’S
SL100 Controller
SL100 is a single board programmable logic controller that includes a number of innovative
features. Key features are:
- 8 digital inputs. The inputs can accept relay contacts or NPN open collector.
- 8 digital outputs. The 8 digital outputs are 500mA Darlington transistors capable of
driving small DC solenoid valves or relay coils.
- 1 analog Input can be configured to operate on 0-10V, 0-20mA or as a temperature measuring input (using an external thermistor sensor)
- All external connections are on plug-in connectors for fast final product assembly.
- 1 analog outputs which can generate a 0-10V signal, with a maximum load current of
5mA. The outputs have internal current limiting
- Provision for modem communications
- An extremely flexible range of expansion possibilities
The SL99 programmer is programmed using a basic type language featuring subroutines which has been tailored for control applications.
For program development all you need is our free software, a simple wall cube power supply and a standard RS232 cable.
The SL99 is available one-off as a Developer's Kit, which includes our resources CD and printed materials.
Price Each
SPL-010 SL100 Development Kit
SPL-011 SL100 Controller Board
1
$189.00
$179.00
5+
less 10%
less 10%
MMI 202 Controller
The MMi202 is a single board programmable logic controller that includes a number of innovative features. Key features are:
•
•
•
•
•
•
•
•
8 digital inputs. The inputs can accept relay contacts or NPN open collector. Input
7 can act as a high speed counter. All other inputs have debouncing
8 digital outputs with LED indicators. The digital outputs are open collector type
implemented using the ULN2803, chip.
2 versatile analog inputs. Each single ended input can be configured to operate on
0-10V, 0-20mA or as a temperature measuring input (using an external thermistor
sensor)
2 analog outputs which can generate a 0-10V signal, with a maximum load current
of 5mA. The outputs have internal current limiting
Onboard Operator Interface, with support for a liquid crystal display (LCD)
Provision for modem communications, RS232 connection with Modbus Communications
PID control
An extremely flexible range of expansion possibilities.
The MMi202 has its own inbuilt operator interface. This gives you push buttons, indicators and a beeper to allow interaction with an operator. It also gives you the ability to
tailor the appearance of your end product via a plastic graphical membrane overlay.
The LCD port supports display sizes from 1x16 to 4x20 (our standard offering is 2x16).
The MMi202 is supplied a several different packages. The packages with "DK" in the name are Developer's Kits.
•
•
MMi202DK. This is the board already mounted onto an aluminium front panel and supplied with a universal graphical overlay. It also includes
a set of matching connectors and software on CD;
MMi202DK216. Like the MMi201DK but with the addition of a 2 line by 16 character Liquid Crystal Display and Real Time Clock;
The MMi202 programmer is programmed using a basic type language featuring subroutines, LCD display control, floating point maths and PID
Price Each
SPL-001 MMI202DK Development Kit
SPL-002 MMI202DK216 Development Kit
Page 74 Ocean Controls Catalog 2009
1
$249.00
$336.00
5+
less 10%
less 10%
OCEAN CONTROLS - PLC OPERATOR PANELS
Prizm 10
Prizm 50
The Prizm 10 is an economical Keypad Based Operator Interface which
when connected to a PLC can display values of PLC registers and
messages and allow data entry into
PLC registers.
Features include
• 16 X 2 back lit LCD
• 6 function keys with macro functions. 2 LEDs
• Floating point
• Serial port for printing screens / alarms
• Free Windows configuration software
• Over 50 PLC's supported
The user can define actions for 3 events: when the key is pressed, while
the key is pressed and when the key is released.
Multiple tasks can be assigned to a single keystroke making it a powerful tool in the machine control environment. It is also possible to assign
actions for a combination of two keys pressed simultaneously.
Price Each
PZM-010 PZM-10-24-B
1
$329.00
Prizm 140
The Prizm 140 is an economical monochrome Touch Screen Operator Panel that
is designed for applications where display
of PLC operations and Data entry into PLC
registers is needed in a Graphical Display.
Features include
• 128x64 Pixels Monochrome Graphical
Display
• Two universal serial ports (Dual Port Support) to connect PLC /
Printer / Programming Port
• Direct connection to most controller families including Modbus RTU
• Up to 65535 user definable screens (full size) or pop-up windows
(partial size)
• Real Time clock
• Wizards for rapid application development of standard bitmapped
objects
• Real Time and Historical alarms
• Real time and Historical trending
• Data logging
• Recipes support
• Backlight screen saver
• Windows® based programming software .........FREE!!
• IP65 design, CE / CSA / UL certification
Price Each
PZM-140 PZM-140-24-B
Page 75 Ocean Controls Catalog 2009
1
$549.00
The Prizm 50 is an economical Keypad
Based Operator Interface which when
connected to a PLC can display values
of PLC registers and messages and
allow data entry into PLC registers.
Features include
• 20 X 4 back lit LCD
• Numeric keys for easy data entry
• 8 function keys with macro functions and LEDs
• Serial port for printing screens, alarms and floating points
• Optional Data Logging function
• Free Windows configuration software
• Over 50 PLC's supported
The user can define actions for 3 events: when the key is pressed, while
the key is pressed and when the key is released.
Multiple tasks can be assigned to a single keystroke making it a powerful tool in the machine control environment. It is also possible to assign
actions for a combination of two keys pressed simultaneously.
Price Each
PZM-050 PZM-50-24-B
1
$499.00
OCEAN CONTROLS - PLC’S AND PERIPHERALS
PROTOCOL GATEWAY
GWY-00 is a Protocol Converter / Data sharer for devices like PLCs, Inverters, Controllers etc. The gateway
has two serial ports that connect with two different devices. The gateway communicates with a device to get
the information required by the other device.
Our Windows® based Gateway setup software makes it easy to configure the protocol converter. After
choosing which protocol to use for each port, you program the Gateway to transfer the data blocks. Using a
simple spreadsheet format, you simply program the Gateway to fetch a specified number of registers or bits
from one device and transfer them to the other. Powerful software allows you to have all of the information
transfers done continuously or allows the PLC to control which block of data is to be transferred.
Features include
- DIN Rail or Panel Mounted compact Protocol Converter
- DB9 Serial ports in any combination of RS232 / RS422 / 2 or 4 wire RS485 / CMOS
- Connects PLC to PLC or PLC to a Modbus Network (as a Master or Slave)
- Allows data sharing between PLC, Invertors, Controllers and other network devices
- Common model for connecting different devices. Several PLC an Invertors supported
- Direct connection to the Programming terminal saves additional hardware
- Low power consumption of only 2.5 Watts
- Common Programming software for the entire Gateway family.........FREE!!
- CE / CSA with UL certification
Price Each
GWY-000 Serial Gateway
1
$336.00
LONWORKS GATEWAY
The LonWorks Gateway communicates between LonWorks network interface on one sde and various
serial protocols on the other side (e.g. Modbus ASCII / RTU etc.). It allows LonWorks devices to make
available their LonWorks variables for PLC’s or SCADA. It also makes possible for serial device to act as a
LonWorks node.
Microsoft Windows® based configuration software, Gateway Setup, helps user to configure Gateway unit.
‘Configuration’ means making the Gateway unit work as per the system requirements. The complete configuration for a unit is termed as ‘Project’. Project comprises of device names, Register
addresses, Conditions for block execution etc.
Features Include
- DIN Rail or Panel Mounted compact Protocol Converter
- Hardware with two communication ports COM1: RS232 / RS422 / 2 or 4 wire RS485 / CMOS
- COM2: LonWorks TP FT10 (78 Kbps, free topology)
- Connect your LonWorks device to serial device or vice versa
- Connect your LonWorks device on Modbus Network (as a Master / Slave)
- Same model can be re-configured for connecting different devices
- Supports up to 62 network variables
- Free software for Gateway and SNVT variables configuration!!
- CE with UL certification
Price Each
GWY-100 LonWorks Gateway
Page 76 Ocean Controls Catalog 2009
1
$385.00
OCEAN CONTROLS - PLC’S AND PERIPHERALS
DigiGate Profibus-Modbus Gateway
The DigiGate Profibus is ideal for connecting a Profibus DP
network with a Modbus RTU network. It works
as a gateway, operating as a master station in the Modbus network and as a slave station in the Profibus network. The DigiGate will read the data of the slaves on the Modbus network and send the values to the Profibus
master. In the same way, it will write at the output of the Modbus slaves according to the Profibus master requests, providing a complete control of the Modbus network devices through the Profibus network.
The device is totally configurable through the application DigiConfig for Windows®, which comes with the product, making access and changing of its parameters easy.
Features include
Profibus:
- Protocol: Profibus DP
- Operates at the entire range of communication rates, from 9600 bps to 12 Mbps
- Addressing range: 0 to 125
- Automatic detection of supported baud rate
- “GSD” file included
- Termination and polarization resistors included (activated by jumper)
- Profibus connection: Terminals for wires, comes with an adapter for DB9
Modbus:
- Operates from 1200 bps to 115200 bps
- Termination and polarization resistors included (activated by jumper)
- Commands available for data reading: “01 Read Coil Status”, “02 Read Input - Status”, “03 Read - Holding Register” and “04 Read Input Register”
- Commands available for data writing: “05 Force Single Coil”, “06 Preset Single Register”, “15 Force - Multiple Coils” and “16 Preset Multiple Registers”
- Protection at the bus: ±60 Vdc, 15 kV ESD
General:
- Operating environment: 0 to 50 °C, 30 to 80% of relative humidity, without condensation
- Mounting: DIN 35 mm rail
- Electrical insulation between the Profibus interface and the rest of the device: 1000 Vac
- Power supply: 10 a 35 Vdc. Internal protection against inverse polarity
- Frontal lit indicators for communication and status
Price Each
SIG-300 Profibus DP / Modbus RTU Gateway
Page 77 Ocean Controls Catalog 2009
1
$495.00
OCEAN CONTROLS - PANEL METERS
N1500 Universal Indicator
The N1500 would have to be the best featured budget priced programmable process indicator on the market. Hundreds have been sold
The standard version comes with key panel programmable range, selectable decimal point, universal switching power supply, 24Vdc output for field
transmitters excitation, ultra bright five digit LED display and 2 relay alarms with 6 function options.
Features are
•
Accepts type J, K, T, E, N, R, S and B thermocouples; Pt100, 4-20 mA, 0-50 mV and 0-10 Vdc
•
Programmable range from –31000 to +31000 with adjustable filter.
•
front panel input of custom created non-linear curve with up to 20 segments. Use this feature
to display volumes in spherical tanks or bullets
•
5 Digit LED display
•
Input sampling: up to 20 per second
•
Maximum and Minimum Memory
•
Peak and Hold Functions
•
2 SPST 3Amp Alarm Relays
•
Alarm Relays can be configured for LO, HI, differential, diff. LO, diff. HI and sensor break
•
Power required 24VDC/AC or 240VAC
Price Each
________1_
•
Dimensions: 48×96×92mm .
IPI-100 N1500 Universal Process Indicator 24VDC
$265.00
•
Work temperature: 0ºC to+55ºC, 35 to 85% humidity.
IPI-101 N1500 Universal Process Indicator 240VAC
$235.00
•
Protection rate Front panel: IP65, Rear panel: IP30
IPI-105 N1500 Process Indicator 24VDC, Analog Out,
RS485, 4 Relays
$299.00
Because it has 2 relay contacts you can program it to operate IPI-102 N1500 Process Indicator 240VAC, Analog Out,
as an ON-OFF Controller and Display unit
RS485, 4 Relays
$299.00
Options include 4 to 20mA output for retransmission of measured IPI-103 N1500G Process Indicator 240VAC, Analog Out,
variable to a recorder or PLC, two extra alarm relays, 1 digital
RS485, Large Digits 60mm High Display
$575.00
N1500 Load Cell Indicator
Features include
•
Input: 4-20mA, 0-20mA, 0-50mV, 0-20mV and –20 to 20mV;
•
10Vcc power supply for load cells;
•
Memory for maximum and minimum values;
•
Hold, peak hold, tare, zero tare and automatic zero functions;
•
2 SPST 3Amp Alarm Relays (4 Alarm Relays is optional)
•
Alarm Relays can be configured for LO, HI, differential, diff. LO, diff. HI
•
•
•
•
•
•
•
•
less10%
less10%
less10%
N480i Process Indicator
N1500 LC is a universal indicator for
use with load cells. It accepts a wide
variety of electric signals and is suitable for Load Cells with 1mV/V, 2mV/V
and 3mV/V output. A six-digit LED
display shows measured value and all
programming parameters of the instrument.
Configuration can be entirely made through the keyboard, no circuit
changes are required. Selection of input and output types, alarms configuration, and other special functions are accessed and programmed
through the front keypad.
•
5+
less10%
less10%
and sensor break
A Process Variable (PV) retransmission in 0-20mA or 4-20mA comes as
standard
Internal resolution: 128000 levels.
This low cost and easy-to-use universal indicator can be programmed by
non-experienced users. Full rangeability and a 24 Vdc output for remote
transmitters are standard.
Features Include
- Input: thermocouples J, K, T, N, R, S;
Pt100, 50 mV, 10V and 4-20mA
- Programmable range from -1999 to +9999
- 2 relay alarms
- Alarm functions: LO, HI, differential, diff.
HI, differential LO and broken sensor.
- Power: 100-240 Vac/dc or 24 Vdc/ac
- option 1 relay alarm can be replaced with
24 Vdc output excitation for transmitters
(only on 240VAC model)
- Detects any sensor failure.
- Easy to use programming menu makes operator interface a snap.
- Front panel: IP65, Polycarbonate UL94 V-2.
- Back panel: IP30, ABS + PC UL94 V-0.
- Dimensions: 48 x 48 x 106 mm
Price Each
1
$159.00
IPI-120 N480i Process Indicator 24VDC Power 2 Relays
IPI-121 N480i Process Indicator 240VAC Power 2 Relays
$159.00
IPI-122 N480i Process Indicator 240VAC Power 1 Relay 24VDC out $159.00
Display resolution: 62000 levels (-31000 to 31000);
IBEST DS8 Digital Universal Indicator
Sampling rate: 15 samples per second;
Maximum error:0.15 of the maximum range;
PV retransmission resolution: 4000 levels, max. 550W
Working temperature: 0 to 55°C, humidity 35 to 85%;
Protection rate
Frontal panel: IP65
Rear panel: IP30
Dimensions:48×96×92mm
Starndard unit is fitted with 2 alarm relays (4 Relays optional), 4-20mA
analog retransmission, RS485 Modbus connection
A Process Variable (PV) retransmission in 0-20mA or 4-20mA comes as
standard
Price Each
IPI-110 N1500LC Load Cell Indicator 24VDC
IPI-111 N1500 LC Load Cell Indicator 240VAC
Page 78 Ocean Controls Catalog 2009
___1_
$399.00
$399.00
5+
less10%
less10%
Features include
-Multi-function sensor indicator, size:48*96*100mm
-Universal input: TC, RTD, mA, mV, A(AA/DA), V
(AV/DV), Rt, 20 segments of customized linear
input. (Configurable by software)
-Up to 3 alarm relays, contact capacity: AC
250V/3A or DC 30V/3A (resistance load)
-Isolated analog output: 0~10mA or 4~20mA, configurable by software.
-Transmitter power supply: DC 24V or DC12V / 30mA max.
-RS485 or RS232 interface
-Product power supply: AC 90~260V 50/60HZ, power consumption<5VA
Price Each
IBI-001 DS8-Digital Universal Indicator
1
$179.00
OCEAN CONTROLS - PANEL METERS
4 Digit Mini Programmable 0-20mA Display
RPM/Line Speed Indicator
This microprocessor controlled meter can be used to display a 4-20mA or 020mA signal in engineering units. The user can set the input value, display
value, zero adjustment and the position of the decimal point. All settings all
done by switches under the front panel cover. All settings are saved to nonvolatile memory
Features include
- 4 Digit LED display range -1999 to 9999
- Accepts a 0-20mA or 4-20mA signal
- adjustable Sampling Time 0.1 to 9.9secs.
- Programmable decimal point position
- Programmable scaling.
- Signal out of range indication
- Programmable scaling. Range 0.1 to 999.9
- Power required 12VDC +/-5% 0.5W or 24VDC +/-5% 0.5W
- Dimensions: 48x24x70mm.
Price Each
CPM-001 Mini-Type 4-20mA Panel Meter 12VDC Powered
CPM-002 Mini-Type 4-20mA Panel Meter 24VDC Powered
1
$99.00
$99.00
4 Digit Mini Display Tachometer
This meter can be used to display the RPM of a engine. It has a programmable scaling factor which you
can divide the pulse source by to correct the reading
to engineering units.
Features include
- 4 Digit LED display 0-9999
- Accepts NPN input signals up to approx 1KHz
- adjustable Sampling Time 0.1 to 9.9secs
- Programmable decimal point position
- Programmable scaling. Range 0.1 to 999.9
- Power required 12VDC +/-5% 0.5W or 24VDC +/-5% 0.5W
- Dimensions: 48x24x70mm.
Price Each
CPM-003 Mini-Type Tachometer/Line Speed Meter 12V powered
CPM-004 Mini-Type Tachometer/Line Speed Meter 24V powered
Price Each
1
ALT-079 LineSpeedMeterAM5H-R-N2M-C-R2NN 24VDC Powered $229.00
ALT-080 LineSpeedMeterAM5H-R-N2M-C-NAY 240VAC Powered $229.00
ALT-081 RPM Meter AM5H-R-N2R-C-NAY 240VAC Powered
$229.00
Digital Panel Meter with 2 Alarms, Pulse Output, RS485
1
$119.00
$119.00
Flow Totaliser Indicator
The KFM-TA is a budget priced programmable totaliser indicator. It accepts a 420mA signal as a rate or flow.
Features Include
- 10 DIGIT MICROPROCESSOR TOTALIZER
METER
- 5 DIGIT MICROPROCESSOR RATE METER
- Rate of display range: 0~99999
- Rate/Total decimal point selectable
- Time unit selectable: sec / min/hour
- Total scale programmable(0.0001~9.9999)
- 2 Alarm Relays
- (15bit resolution) optional
- Roof square function available for analog input
- Reset for Total by external control input
- CEapproval
- High stability, non-flammablecase(PC), highsafety
- Pulse Output
Specifications
- Accuracy: Analog input: +/-0.1% F.S. +/-1digit
Pulse Input +/-0.03%FS
- Display Screen: High brightness red LED; 10.2mm(0.4")
- Analog Sampling Time: 16 cycles/sec
- Pulse Sampling Time: 10 cycles/sec (>10Hz); f cycles/sec (<10Hz)
- Max. Input Frequency: 100KHz (50% duty cycle)
- Display Range: Rate: 0~99999; Total: 0~9999999999
- Parameters Setting: Push buttons
- Back Up Memory: EEPROM
- Over Range Indication: doFL/ioFL
- Temperature Coefficient: 100ppm/degC(0~60degC)
- Operating Temperature: 0 to 60degC
- Operating Humidity: 20 to 90% RH(non condensing
- Storage Temperature -10-70degC
- Operating Humidity: 20 to 90% RH(non condensing
- Power Supply 24VDC
- Power Consumption: 8.5VA (all functions output)
Dimensions: 96x48x112mm.
Price Each
ALT-090 Analog 4-20mA Rate Totaliser Meter
Page 79 Ocean Controls Catalog 2009
The AM5H is a budget priced 5 digit Panel
Meter which is available in 2 models. The first
is a RPM indicator. The other is a line speed
indicator. Both models feature a 4-20mA analog retransmission signal and a RS485 modbus connection.
Features Include
- 5 DIGIT MICROPROCESSOR RATE METER
- Highbrightness 0.8" LEDdisplay:0~99999;
decimalpoint selectable
- Line-Speed/RPM/Frequency selectable; Lineunit:M/min
- RPM pulse input programmable:1~99999
- RS-485 communications
- Analog output (15bit resolution)
- CE approval
- Highstability , non-flammablecase(PC),highsafety
- Accuracy: 0.03%F .S
- Measuring NPN DC Pulse Input frequency:0.001Hz~100KHz
Dimensions: 96x48x112mm.
Models available
Line Speed Meter AM5H-R-N2M-C-NAY
RPM Meter AM5H-R-N2R-C-NAY
1
$450.00
Features:
*Measuring power parameters: V, A, W, Q (Var), S (VA), PF, Hz, KWH, KQH,
DM (Demand)
*1P2W/1P3W/3P3W/3P4Wsystemprogrammable
*Display range:-9999 to 9999; decimal point selectable
*2Alarms output or 2 Digital input / 2 Pulses output for forward KWH & reverse KWH RS-485communicationoptional (The above option can be exist
together)
8DIN case: 96x96mm
*High stability, non-flammable case (PC), high safety
Specification:
*Accuracy: ±0.25% for VL-N: V1, V2, V3, VE; ±0.25% for VL-L: V12, V23,
V13, VE; ±0.25% for A: A1, A2, A3, AE; ±0.5% for W (Watt): W1, W2, W3,
ΣW; ±0.5% for Q (Var): Q1, Q2, Q3, ΣQ; ±0.5% for S(VA): S1, S2, S3, ΣS;
±0.5% for PF: PF1, PF2, PF3, ΣPF; ±0.1% for Hz; ±0.5% for KWH; ±0.5% for
KQH; ±0.5% for DM (Demand)
*Measuring Range: 1P2W, 1P3W, 3P3W, 3P4Wsystems; Voltage: 0 to
600Vac; Current: 0 to 5Aac; Frequency: 50/60 Hz
*Display Screen: High brightness LED; 14.22mm (0.56"); High brightness
LED; 10.2mm (0.4")
*Sampling Time: 1 cycle / sec
*Display Range: - 9999 to 9999; 0 to 999999999 for KWH & KQH
*Parameters Setting: Push buttons
*Back up Memory: EEPROM
*Alarm Action: “≥ (Hi) on” or “< (Lo) on”
*Alarm Run Delay Time: 0 to 99 sec
*Relay Contact: AC277V/7A; DC 30V/7A
*Communication: RS-485 Modbus RTU mode
*Baud Rate: 19200/9600/4800/2400 bps
*Temperature Coefficient: 100ppm/°C (0 to 60°C)
*Operating Temperature: 0 to 60°C
*Operating Humidity: 20-90 % RH (noncondensing)
*Storage Temperature: -10 to 70°C
*Storage Humidity: 20-90 % RH (non-condensing)
*Power Supply: AC100 to 240V; DC 24/30 to 90V
*Power Consumption: 10VA (all functions output)
*Surge Test: 1KVac/1MIN (Input/Power); 3KVac/1min (Terminals/Case)
*Insulation Resistance: >100MΩ with 500Vdc
*Input Impendence: Voltage: >2V for 20K / V; 2V for >200MΩ; Current:
=>0.2A at 100mV; <0.2A at 1V
*Safety: IEC 61000-4-2; IEC 61000-4-3; IEC 61000-4-4; IEC 61000-4-5; IEC
61000-4-6; IEC 61000-4-8; IEC 61000-4-11
Price Each
1
ALT-022 Digital Panel Meter with 2 Alarms, Pulse Output, RS485 $449.00
OCEAN CONTROLS - PANEL METERS
Basic 16x2 Character LCD FSTN - White on
Basic 20x4 Character LCD Black on Green
This is a basic 16 character by 2 line display
with a snazzy black background with white
characters. Utilizes the extremely common
HD44780 parallel interface chipset (datasheet).
Interface code is freely available. You will need
~11 general I/O pins to interface to this LCD
screen. Includes white LED backlight. Works
with our LCD Serial Module.
Price Each
LCD-011 16x2 Basic LCD White on Black
LCD-012 16x2 Basic LCD Yellow on Blue
LCD-013 16x2 Basic LCD Red on Black
This is a basic 20 character by 4 line display.
Utilizes the extremely common HD44780
parallel interface chipset (datasheet). Interface code is freely available. You will need
~11 general I/O pins to interface to this LCD
screen. Includes LED backlight. Works with
our LCD Serial Module
1
$19.95
$19.95
$19.95
5+
less 10%
less 10%
less 10%
Basic 16x2 Character LCD STN - Black on Green
This is a basic 16 character by 2 line display.
Black text on Green background. Utilizes the
extremely common HD44780 parallel interface
chipset (datasheet). Interface code is freely
available. You will need ~11 general I/O pins
to interface to this LCD screen. Includes LED
backlight. Works with our LCD Serial Module.
Price Each
LCD-002 16x2 Basic LCD Black on Green
1
$17.50
5+
less 10%
Serial LCD Module
The SerLCD v2.5 module is the latest serial LCD module from Spark Fun
Electronics that incorporates many new features. The SerLCD backpack
takes care of all the HD44780 commands allowing seamless integration with
any micro that can communicate over a wide range of TTL serial baud rates.
The SerLCD v2.5 has the ability to drive up to 1A directly for backlight control
or as a general purpose high-power control pin.
SerLCD v2.5 currently supports 16 and 20 character wide screens with 2 or 4
lines of display. Contrast control is implemented through a trim pot on the
module. Comes with 3-pin screw terminal shown on right.
Features:
* Adjustable baud rates of 2400, 4800, 9600 (default), 14400, 19200 and
38400
* Operational Backspace
* Greater processing speed at 8MHz
* Incoming buffer stores up to 80 characters
* Backlight transistor can handle up to 1A
* Pulse width modulation of backlight allows
direct control of backlight brightness and current
consumption
* All surface mount design allows a backpack that
is half the size of the original
* Faster boot-up time
* Boot-up display can be turned on/off via firmware
* User definable splash screen
Price Each
LCD-001 Serial LCD Module
1
$21.95
5+
less 10%
Basic 8x2 Character LCD FSTN - White on Blue
This is a basic 8 character by 2
line display with a snazzy blue background with white characters. Utilizes the extremely common HD44780 parallel interface
chipset (datasheet). Interface code is freely
available. You will need ~11 general I/O pins to
interface to this LCD screen. Includes white LED backlight.
Price Each
LCD-003 8x2 Basic LCD White on Blue
Page 80 Ocean Controls Catalog 2009
1
$9.50
Price Each
LCD-032 20x4 Basic LCD Black on Green
5+
less 10%
Color LCD 128x128 with carrier board
Description: Stop trying to solder the 0.5mm pitch Color LCD connector
and start playing! This breakout board comes fully tested and assembled
with it's own Nokia LCD. The Color LCD Carrier Board requires only
3.3V and boosts this voltage to drive the LED backlight at 6.5V. The
multiple solder jumpers allow the end user to get complete access to the
LCD connector if needed. Only 6 connections are need for basic operation:
* +Vin (3.3V)
* CS (Chip Select)
* SCLK (Serial Clock)
* SDATA (Serial Data)
* RST (Reset)
* GND (Ground)
Carrier board comes fully assembled and
tested and includes a Nokia Color LCD.
Special Note:
The Nokia LCDs are sensitive to electrical noise on the Vdsp supply line (Pin 6 on LCD). This line provides power for the LCD itself while
Vdig supplies power to the screens controller and interface logic. This
breakout board allows several different power configurations using jumpers. By default the board takes a single 3.3 volt input to power the
booster circuit and both Vdsp and Vdig. This configuration causes large
amounts of noise on Vdsp that can cause the screen to flicker randomly. For best results use a separate 3.3 volt supply for Vdsp. If a
separate regulated 3.3 volt supply is not available for Vdsp, try a 100uF
capacitor between Vdsp and GND which might provide acceptable performance.
Price Each
LCD-050 Color LCD and Carrier Board
1
$49.50
5+
less10%
Color LCD 128x128 without carrier board
Description: Finally! Color LCDs you can afford and play with! What SFE
found over in China is a 'copy' of the Nokia LCD found in models 6100, 6610,
7210, 7250, and 5100? We don't know what phones it fits, and we don't really
care. This inexpensive LCD comes with a powerful white LED backlight and a
relatively simple serial interface. It's a 9-bit interface, so beware. But we were
able to get the LCD up and running on a LPC2138 with a few hours worth of
work.
Please note: Comes with a carrier board so you can
easily interface to the LCD
Frame Dimensions: 1.35x1.58"
Active Display Dimensions: 1.2"x1.2"
Features:
* LCD Logic - 3.3V @ 2-3mA
* LED Backlight - 7V @ 40-50mA (very bright)
* Full 4,096 Color Display
* Uses the Epson S1D15G10 Compatible Controller
Price Each
LCD-051 Color LCD without Carrier Board
5+
less 10%
1
$29.95
1
$25.00
5+
less10%
OCEAN CONTROLS - PANEL METERS
EL Sequencer
7-Segment Red 6.5" Display
Description: The EL Sequencer is a ATmega based control
board that allows the user to program any sequence of blink, on/
off, even PWM pulsing of EL wire.
Electroluminescent wire is this really neat, flexible cord that emits a florescent
light. Some times referred to as 'cool neon' because the cord does not heat
up. The kicker is that EL wire runs on high voltage AC - about 125V at
425Hz. While EL wire requires very little power, you can't use normal transistors to turn on/off a string of it. So we created the EL Sequencer that uses
TRIACs to control up to 8 channels.
Features:
* ATmega168V
* Board can be powered from USB or LiPo
* Switch chooses source and acts as on/off
* Compatible with Arduino (8MHz LilyPad)
* TRIAC part #: Z0103MN
* 8 TRIACs can handle up to 600V
* Control 8 channels of EL
* Runs on 3.7V LiPo
* Footprint for connection to FTDI Basic for downloading code
* Footprint for connection to Nordic nRF24L01 2.4GHz wireless module
Price Each
LIG-001 EL Sequencer
1
$38.27
5+
less10%
Serial Graphic LCD 160x128
Description: This is a very large
serial graphic LCD. The Serial Graphic
LCD backpack is soldered to the 160x128
pixel “Huge” Graphic LCD and provides the user a
simple serial interface to a full range of controls.
Features:
* Voltage: 6V – 7V DC
* Current: 220mA (backlight at 100%)
* Input: 0-5V, 115,200bps (adjustable), 8 data bits, 1 stop bit, no parity
Dimensions: 4x5x0.65" (102x129x17mm)
1
$109.95
5+
less10%
Serial Graphic LCD 128x64
Description: This is a smaller version of our serial graphic
LCD. The Serial Graphic LCD backpack is soldered to the 128x64
pixel Graphic LCD and provides the user a simple serial interface to a
full range of controls.
Besides writing text, this serial graphic LCD allows the user to draw lines,
circles and boxes, set or reset individual pixels, erase specific blocks of the
display, control the backlight and adjust the baud rate. Additionally, all source
code for the ATMega168 processor is compiled using the free WinAVR compiler and is free for downloading.
Features:
* Voltage: 6V – 7V DC
* Current: 220mA (backlight at 100%)
* Input: 0-5V, 115,200bps (adjustable), 8 data
bits, 1 stop bit, no parity
Dimensions: 2x2.45"
Price Each
LCD-061 Serial Graphic LCD 128x64
Page 81 Ocean Controls Catalog 2009
Description: No really - it's 6 inches (153mm) tall! This
very large 7-segment display can be seen from a hundred
feet away. So many projects to try, so little time...
Price Each
LCD-100 7-
1
Segment Red 6.5" Display
$23.95
5+
less 10%
7-Segment Serial Display
Description: The 7-Segment Serial
Display turns the thirteen pins necessary
to control a 4-digit 7-segment display into just one
or three. The display will give you full control of all
digits, decimal points, the colon and the apostrophe. At the heart of the display is an ATMega168
which controls all the serial communications and
the 4-digit 7-segment display through an easy to
use API.
The Serial 7-Segment Display can be controlled in one of two ways: (1) serial
TTL communication or (2) SPI serial communication. Regardless of which
method you use to communicate with the display, the display is controlled
with 4-byte packets and special 2-byte commands.
Features:
Besides writing text, this serial graphic LCD allows the user to draw lines, circles and boxes, set
or reset individual pixels, erase specific blocks of
the display, control the backlight and adjust the
baud rate. There's also a reverse mode that allows the screen to operate blue on white instead of white on blue. Additionally, all source code for the ATMega168 processor is compiled using the free
WinAVR compiler and is free for downloading.
Price Each
LCD-060 Serial Graphic LCD
7-Segment Red 6.5" Display
1
$41.92
5+
less10%
* 4 digit alpha-numeric display with serial (1 pin) or SPI interface (3 pins)
* Display numbers (0-9) and letters (A-F)
* Control multiple decimal points, apostrophe, and colon
* Selectable baud rate (4800 to 57600 bps)
* Selectable brightness (255 different levels)
Price Each
LCD-110 7-Segment Serial Display
1
$21.50
5+
less 10%
7-Segment Panel Meter Display
Features:
• Large 6” 7-Segment Display
• Easily add digits to display higher values
• 2 x opto-isolated inputs
• 1 x 10-bit 0-5V input
• 1 x 10-bit 0-20mA input
• RS485 Serial, TTL Serial
• RS232 Serial or USB Serial with
additional converters
• 12-17VDC Powered
Have you ever had the need for a display that can be read from across
the room? How about across the factory? How about 50m away? This
display uses Large 6” (15cm), 7-Segment displays and can be expanded
to use up to 10 digits, without costing upwards of a thousand of dollars.
But what does it display? The display has been designed to accept multiple input signals, for maximum flexibility. Parameters are set using a
computer and saved to memory.
Input signal types:
• 0-5V Scaled
• 0-20mA or 4-20mA Scaled
• Up/Down Counter with Reset and Preset
• Quadrature Up/Down Counter
• Tachometer RPM
• Frequency
• Up/Down Second Timers
• ASCII or Modbus Serial over RS485 or TTL
• (or RS232 using COV-201)
• (or USB using ARD-011)
Price includes Red Acrylic
Price Each
KTA-255 Main Controller Digit
KTA-256 Slave Digit
KT5-255 5 Digit Panel Meter
COV-201 RS232 to TTL Converter
ARD-011 FTDI Basic Breakout
1
$119.00
$69.00
$349.00
$14.95
$21.50
5+
less 10%
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - SIGNAL CONDITIONERS
Programmable Non Isolated TxBlock
Programmable Non Isolated TxRail
The TxBlock is a programmable head mount 4-20mA temperature transmitters. One single model can be configured to accept several thermocouple types and Pt100 RTD. output.
Specifications
Programmable input: thermocouples type
J,K,T,N,E,R,S,B, and Pt100 RTD
2-wire loop powered 4-20mA output
Power supply: 12 to 30 Vdc.
Linearized output and cold junction compensation for
thermocouples.
2 or 3-wire Pt100 with linearization
Accuracy: +-0.2% full scale for Pt100 and 0.3% max. of FS for thermocouples.
Programmable working range. We can program it for you at no charge
Price Each
SIG-001 TxBlock Non Isolated Head Mount Transmitter
SIG-007 TxConfig PC Interface and Configurator Software
1
$89.00
$89.00
Programmable Isolated TxBlock
The TxRail is a programmable DIN rail mount 4-20mA temperature
transmitters. One single model can be configured to
accept several thermocouple types and Pt100 RTD.
output.
Specifications
Programmable input: thermocouples type
J,K,T,N,E,R,S,B, and Pt100 RTD
2-wire loop powered 4-20mA output (Option 0-10V
output)
Power supply: 12 to 30 Vdc.
Linearized output and cold junction compensation for
thermocouples.
2 or 3-wire Pt100 with linearization
Accuracy: +-0.2% full scale for Pt100 and 0.3% max. of FS for thermocouples.
Price Each
SIG-002 TxRail Non Isolated DIN Mount 4-20mA
SIG-003 TxRail Non Isolated DIN Mount 0-10V
SIG-007 TxConfig PC Interface and Configurator Software
1
$99.00
$99.00
$89.00
Programmable Isolated TxRail
The TxBlock is a programmable head mount 4-20mA
temperature transmitters. One single model can be configured to accept several thermocouple types and Pt100
RTD. output.
The TxRail is a programmable DIN rail 4-20mA temperature transmitters. One single model can be configured to accept several thermocouple types and Pt100 RTD. output.
Specifications
Programmable input: thermocouples type
J,K,T,N,E,R,S,B, and Pt100 RTD
2-wire loop powered 4-20mA output
Power supply: 12 to 30 Vdc.
Linearized output and cold junction compensation for thermocouples.
2 or 3-wire Pt100 with linearization
Accuracy: ±0.15% full scale for Pt100 and 0-50mV and 0.25% max. of
full scale ±1ºC for thermocouples.
Isolation: 1500Vac between sensor input and 4-20mA output loop.
Programmable working range. We can program it for you at no charge
Specifications
Programmable input: thermocouples type
J,K,T,N,E,R,S,B, and Pt100 RTD
2-wire loop powered 4-20mA output (Option 0-10V output)
Power supply: 12 to 30 Vdc.
Linearized output and cold junction compensation for
thermocouples.
2 or 3-wire Pt100 with linearization
Accuracy: ±0.15% full scale for Pt100 and 0-50mV and 0.25% max. of
full scale ±1ºC for thermocouples.
Isolation: 1500Vac between sensor input and 4-20mA output loop.
Programmable working range. We can program it for you at no charge
Price Each
SIG-004 TxBlock Isolated Head Mount Transmitter
SIG-007 TxConfig PC Interface and Configurator Software
Price Each
SIG-005 TxRail Isolated DIN Mount 4-20mA
SIG-006 TxRail Isolated DIN Mount 0-10V
SIG-007 TxConfig PC Interface and Configurator Software
1
$139.00
$89.00
1
$139.00
$139.00
$89.00
4-20mA Loop Isolation Modules
Loop isolators provide signal protection by electrically isolating the input signal from the output.
TxIsoLoop-1 and TxIsoLoop-2 simplify your application and avoid the undesirable ground loops by providing single and dual loop galvanic isolation.
The 0/4-20 mA input is measured and an identical isolated signal is reproduced at the output. Power is drawn from the 0(4)-20 mA input loop, thus no
external power supply is needed.
Specifications
- Input Signal (INPUT): 0 to 20 mA; 4 to 20 mA (check minimum current - for proper operation)
- Maximum Input voltage (Vin max.): 32 Vdc
- Voltage Drop (Vdrop): < 3 Vdc
- Output Signal (OUTPUT): 0(4) to 20 mA
- Max. Load (RL): 1450 R
- Accuracy: 0.2 % FS @ 0 a 60 °C / RL= 250 R; 0.3 % FS @ -20 a 75 °C / RL= 250 R
- Operating current: > 0.1 mA
- Overload: < 40 mA; < 32 Vdc
- Response time: 2 ms @ RL= 250 R
- Isolation: 3000 Vac / 10 s; 240 Vac continuous
- EMC: EN 61326-1
- Ambient temperature range: -20 to + 75 °C
- Humidity: 20 to 90 % RH
- Protection: IP40
Price Each
- Wire gauge for connections: 0.14 to 1.5 mm²
SIG-201 TxIsoloop-1 Single Loop Isolator
- Recommended torque: 0.8 Nm
SIG-202 TxIsoloop-2 Dual Loop Isolator
- Terminal blocks injected in Polyamide
Page 82 Ocean Controls Catalog 2009
1
$129.00
$219.00
OCEAN CONTROLS - SIGNAL CONDITIONERS
Frequency to Analog Converter with 2 Alarms
Our frequency to analog converter allows
you to convert the frequency of a pulse
stream to an analog voltage 0 to 10V or 420mA.
The converter has a RS232 serial port
9600 baud which allows you to configure
the card and read the frequency using the
popular Modbus protocol. The configuration is automatically saved to EEPROM
so your configuration will be retained in
the event of power loss
Two on board relays can be used as
alarm contacts if the frequency rises
above or falls below set limits.
Frequency range is 5 to 10KHz or 5 to 65000RPM.
The pulse stream can be 0 to 5V signal or a NPN signal.
12 to 15VDC powered.
The converter can be DIN rail mounted.
Measures 107(L) x 87(W) x 24(H)mm
Price Each
1
5+
KTA-215 Frequency to Analog Converter Assembled $114.50 less 10%
Page 83 Ocean Controls Catalog 2009
Dual Frequency to Analog Converter
Our Dual frequency to analog converter
allows you to easily convert up to two frequency signal streams to an analog voltage
signal
The KTA-245 is not designed for unlimited
frequencies but for most applications it is
suitable. 60KHz is combined maximum
frequency of the two frequency inputs. ie. If
channel 1 is 60KHz you cannot use channel 2, but if channel 1 is 40KHz the maximum for channel 2 is 20KHz.
Realistically, most
signals will be in the 10KHz or below range.
To set up the two ranges of the analog outputs there are four switch
blocks on the PCB. A rotary switch sets the base frequency and a dual
DIP switch sets the multiplier
For ease of installation, the KTA-245 unit can be supplied with DIN rail
Price Each
KTA-245 Dual Freq to Volt Converter
KTD-245 Dual Freq to Volt Converter
1
5+
$99.00 less 10%
$129.00 less 10%
OCEAN CONTROLS - SENSORS
QL-1805 DC Square Proximity Switch
QL-1808 DC Square Proximity Switch
Proximity switch inductive NPN or PNP rectangular shape
Dimensions 36 x 18 x 18mm
Secure Sensing Range 0-4mm
Suitable for Limit/Speed
Switches
Supply Voltage 10-30VDC
Voltage Drop <=1.5V
Degree of Protection IP67
Maximum Output Current 150mA
Power Absorbed <10mA
Operating Frequency 600Hz
Temperature/Humidity -20 to +70degC/ 35 to 95%RH
Price Each
1
PXS-001 DC Proximity Switch QL-1805NA NPN $22.50
PXS-002 DC Proximity Switch QL-1805PA PNP $22.50
5+
less 10%
less 10%
TS-0802 Tubular Proximity Switch
Proximity switch inductive tubular shape
Dimensions 8mm Dia x 40mm Long
Secure Sensing Range 0-1.6mm
Suitable for Limit/Speed Switches
Supply Voltage 10-30VDC
Degree of Protection IP67
Maximum Output Current 150mA
Power Absorbed <10mA
Voltage Drop <=1.5V
Operating Frequency 1KHz
Temperature/Humidity -20 to +70degC/ 35 to 95%RH
Price Each
PXS-100 Tube Proximity Switch TS-0802NA NPN
PXS-101 Tube Proximity Switch TS-0802PA PNP
1
$44.50
$44.50
5+
less 10%
less 10%
Proximity switch inductive NPN or PNP tubular shape
Dimensions 18mm Dia x 40mm Long
Secure Sensing Range 0-4mm
Suitable for Limit/Speed
Switches
Supply Voltage 10-30VDC
Voltage Drop <=1.5V
Power Absorbed <10mA
Degree of Protection IP67
Maximum Output Current 150mA
Operating Frequency 600Hz
Temperature/Humidity -20 to +70degC/ 35 to 95%RH
1
$39.00
$39.00
Proximity switch inductive NPN or
PNP tubular shape
Dimensions 30mm Dia x 40mm
Long
Secure Sensing Range 0-12mm
Suitable for Limit/Speed Switches
Supply Voltage 10-30VDC
Degree of Protection IP67
Maximum Output Current 150mA
Power Absorbed <10mA
Voltage Drop <=1.5V
Operating Frequency 100Hz
Temperature/Humidity -20 to +70degC/ 35 to 95%RH
Page 84 Ocean Controls Catalog 2009
5+
less 10%
less 10%
Proximity switch inductive tubular shape
Dimensions 12mm Dia x 40mm Long
Secure Sensing Range 0-3.2mm
Suitable for Limit/Speed Switches
Supply Voltage 10-30VDC
Degree of Protection IP67
Maximum Output Current 150mA
Power Absorbed <10mA
Voltage Drop <=1.5V
Operating Frequency 600Hz
Temperature/Humidity -20 to +70degC/ 35 to 95%RH
Price Each
PXS-104 Tube Proximity Switch TS-1204NA NPN
PXS-105 Tube Proximity Switch TS-1204PA PNP
1
$39.00
$39.00
5+
less 10%
less 10%
TS-1808 Tubular Proximity Switch
5+
less 10%
less 10%
TS-3015 Tubular Proximity Switch
Price Each
1
PXS-003 DC Proximity Switch QL-1808NA NPN $25.00
PXS-004 DC Proximity Switch QL-1808NA PNP $25.00
TS-1204 Tubular Proximity Switch
TS-1805 Tubular Proximity Switch
Price Each
PXS-110 Tube Proximity Switch TS-1805NA NPN
PXS-111 Tube Proximity Switch TS-1805PA PNP
Proximity switch inductive NPN or PNP rectangular shape
Dimensions 36 x 18 x 18mm
Secure Sensing Range 0-8mm
Suitable for Limit/Speed
Switches
Supply Voltage 10-30VDC
Voltage Drop <=1.5V
Degree of Protection IP67
Maximum Output Current 150mA
Power Absorbed <10mA
Operating Frequency 200Hz
Temperature/Humidity -20 to +70degC/ 35 to 95%RH
Proximity switch inductive NPN or PNP tubular shape
Dimensions 18mm Dia x 40mm Long
Secure Sensing Range 0-6.4mm
Suitable for Limit/Speed
Switches
Supply Voltage 10-30VDC
Voltage Drop <=1.5V
Power Absorbed <10mA
Degree of Protection IP67
Maximum Output Current 150mA
Operating Frequency 200Hz
Temperature/Humidity -20 to +70degC/ 35 to 95%RH
Price Each
PXS-116 Tube Proximity Switch TS-1808NA NPN
PXS-117 Tube Proximity Switch TS-1808PA PNP
Price Each
PXS-112 Tube Proximity Switch TS-3015NA NPN
PXS-113 Tube Proximity Switch TS-3015PA PNP
1
1
$39.00
$39.00
5+
$49.00 less 10%
$49.00 less 10%
5+
less 10%
less 10%
OCEAN CONTROLS - SENSORS
IPS-S30NOC15B IBEST S30 Inductive Proximity Sensor
IPS-18NO10B IBEST M18 Proximity Sensor Inductive
Dim: 30×30×53mm, rectangular.
DC 2-wire (10-30V DC), DC 3-wire(10-30V
DC), DC 4-wire(10-30V DC),
Mounting distance: 15mm Detection distance:15mm
With LED operation indicate lamp, easily
identifiable
Standard sensing object: ferrous metals;
Protection rate: IP67, water resistant
Over-current and short circuit protection; Against polarity reversal.
Widely applied in measuring, Counting, Rpm measuring in
mechanism, chemical, paper manufacture light industry, etc
Rated operational voltage (DC/AC): 24VDC
Supply voltage (DC/AC): 10-30VDC
Voltage drop: <=2.0V
Rated insulation voltage: >=20MΩ
Load current capacity (DC/AC): 200mA
Off-state current (NPN/PNP): <=15mA
Leak current: <=20µA
Against polarity reversal: YES
Short circuit protected: YES
Load capacity: <=1µF
Repeated accuracy: <=5%
Ambient temperature range: -25...+70degC
Frequency (DC 3/2 wires 800Hz
Function indication: Red LED Indicator
IP ratings: IP67
Housing material: Nickle plated brass
Material of sensing face: ABS
Standard length of cable: 2m
Detection distance:10mm
Approvals: CE
Price Each
IBP-001 Proximity Sensor Inductive NPN
Price Each
IBP-002 Proximity Sensor Inductive IPS-S30NOC15B
1
5+
less 10%
IPS-F54NOC36B IBEST F54 Inductive Proximity Sensor
Dim: 54×35×76.8, protruding.
DC 2-wire (10-30V DC), DC 3-wire(1030V DC), DC 4-wire(10-30V DC)
Mounting distance: 25mm Detection distance:36mm
With LED operation indicate lamp, easily
identifiable
Standard sensing object: ferrous metals;
Protection rate: IP67, water resistant
Over-current and short circuit protection; Against polarity reversal.
Widely applied in measuring, Counting, Rpm measuring in
mechanism, chemical, paper manufacture light industry, etc
1
5+
$45.00 less 10%
CPS-18PO5B IBES M18 Proximity Sensor Capacitive
Capacitive sensor, style: cylinder shape , diameter: 18mm
Shielded or unshielded type;
DC 2-wire (10-30V DC), DC 3-wire(10-30V DC), DC 4-wire(1030V DC),
Connection mode: 3/4 wire
Mounting distance: shielded: 2mm / unshielded: 4mm Detection distance:5mm
With LED operation indicate lamp, easily
identifiable
Brass chrome plated, proof of oil, water
acid, alkaline
Standard sensing object: metal or nonmetal objects.
Protection rate: IP67, water resistant
Over-current protection
Widely applied in measuring, Counting, Rpm measuring in
mechanism, chemical, paper manufacture light industry, etc
Price Each
IBC-001 Proximity Sensor Capacitive CPS-18PO5B
IBC-002 Proximity Sensor Capacitive CPS-18NOC8B
Page 85 Ocean Controls Catalog 2009
5+
IPS-F36NOC15B IBEST S36 Inductive Proximity Sensor
$17.85
Price Each
IBP-004 Proximity Sensor Inductive IPS-F54NOC36B
1
$39.00 less 10%
1
Dim: 36×17.5×51.5mm, protruding.
DC 2-wire (10-30V DC), DC 3-wire(10-30V
DC), DC 4-wire(10-30V DC)
Mounting distance: 15mm Detection distance:15mm
With LED operation indicate lamp, easily
identifiable
Standard sensing object: ferrous metals;
Protection rate: IP67, water resistant
Over-current and short circuit protection; Against polarity reversal.
Price Each
IBP-003 Proximity Sensor Inductive IPS-F36NOC15B
1
5+
$39.00 less 10%
IPS-F100NOC50B IBEST F100 Inductive Proximity Sensor
Dim: 100×100×50, protruding.
DC 2-wire (10-30V DC), DC 3-wire(10-30V
DC), DC 4-wire(10-30V DC),
Mounting distance: 50mm Detection distance:50mm
With LED operation indicate lamp, easily identifiable
Standard sensing object: ferrous metals;
Protection rate: IP67, water resistant
Over-current and short circuit protection; Against polarity reversal.
Widely applied in measuring, Counting, Rpm measuring in
mechanism, chemical, paper manufacture light industry, etc
Price Each
IBP-005 Proximity Sensor Inductive IPS-F100NOC50B
1
5+
$55.00 less 10%
CPS-30NOC15B IBES M30 Proximity Sensor Capacitive
Capacitive sensor, style: cylinder shape , diameter: 30mm
Shielded or unshielded type;
DC 2-wire (10-30V DC), DC 3-wire(10-30V
DC), DC 4-wire(10-30V DC),
Connection mode: 3/4 wire
Mounting distance: shielded: 2mm / unshielded: 4mm Detection distance:15mm
With LED operation indicate lamp, easily identifiable
Brass chrome plated, proof of oil, water acid, alkaline
Standard sensing object: metal or non-metal objects.
Protection rate: IP67, water resistant
Over-current protection
5+
$49.00 less 10%
$49.00 less 10%
Price Each
IBC-003 Proximity Sensor Capacitive CPS-30NOC15B
1
5+
$59.00 less 10%
OCEAN CONTROLS - SENSORS
CPS-S41NOC20B IBES S41 Proximity Sensor Capacitive
CPS-F36NOC15B IBES F36 Proximity Sensor Capacitive
Capacitive sensor, style: rectangular
Shielded or unshielded type;
DC 2-wire (10-30V DC), DC 3-wire(10-30V
DC), DC 4-wire(10-30V DC),
Connection mode: 3/4 wire
Mounting distance: shielded: 2mm / unshielded: 4mm Detection distance:20mm
With LED operation indicate lamp, easily identifiable
Brass chrome plated, proof of oil, water acid, alkaline
Standard sensing object: metal or non-metal objects.
Protection rate: IP67, water resistant
Over-current protection
Widely applied in measuring, Counting, Rpm measuring in
mechanism, chemical, paper manufacture light industry, etc
Price Each
1
5+
IBC-004 Proximity Sensor Capacitive CPS-S41NOC20B $59.00 less 10%
LS18R-300P Tubular IR Photo Electric Switch
Transistor Output PNP
Output Mode switchable "Light On"
or "Dark On"
Reflection Type with Reflector
Dimensions 18mmDia x 68mm Long
Detecting Distance 0.1-3m
Supply Voltage 10-30VDC
Power Consumption 15mA max
Maximum Output Current 100mA at 24VDC
Voltage Drop <=1.5V
Detecting Delay Time 2ms
Degree of Protection IP66
Temperature/Humidity -25 to +50degC/ 35 to 85%RH
Price Each
PES-003 Photo Electric Switch LS18R-300P
1
$52.50
5+
less 10%
LS3-3MR IR Photo Electric Switch
Retro-Reflection Switch with Relay
Output
Dimensions 50mm x 55mm x 21mm
Detecting Distance 0.1-3m
Detects Opaque Objects (4.5cm min.)
Supply Voltage 12-240VDC 24-240VAC
Degree of Protection IP54
Relay Output 250V/5A
Power Absorbed <2W
Temperature/Humidity -25 to +50degC/ 35 to 85%RH
Price Each
PES-005 Photo Electric Switch LS3-3MR
1
$72.50
5+
less 10%
Output: NPN, NO(NC)
Install: Unshielded
Mount D: 15mm
Detect D: 15mm
IP rating: IP67
Price Each
1
5+
IBC-005 Proximity Sensor Capacitive CPS-F36NOC15B $65.00 less 10%
LS18D-40P Tubular IR Photo Electric Switch
Transistor Output PNP
Output Mode switchable "Light On" or
"Dark On"
Diffuse Reflection Type
Dimensions 18mmDia x 68mm Long
Detecting Distance 0-40cm(10x10cm
white paper with no reflection)
Supply Voltage 10-30VDC
Power Consumption 15mA max
Maximum Output Current 100mA at 24VDC
Voltage Drop <=1.5V
Detecting Delay Time 2ms
Degree of Protection IP66
Temperature/Humidity -25 to +50degC/ 35 to 85%RH
Price Each
PES-001 Photo Electric Switch LS18D-40P
1
$44.50
5+
less 10%
LS3-1MD IR Photo Electric Switch
Diffused Reflection Switch with Relay Output
Dimensions 50mm x 55mm x 21mm
Detecting Distance 0-100cm
Detects Transparent/Opaque Objects
Supply Voltage 12-240VDC 24240VAC
Degree of Protection IP54
Relay Output 250V/5A
Power Absorbed <2W
Temperature/Humidity -25 to +50degC/ 35 to 85%RH
Price Each
PES-004 Photo Electric Switch LS3-1MD
1
$67.50
5+
less 10%
LS18-15MT IR Photo Electric Switch
Through Beam - Consist of transmitter LS18T-1500X and detector
LS18T-1500N with NPN Output
Dimensions 18mmDia x 68mm
Long
Detecting Distance 0.1-15m
Detects Opaque Objects (1cm
min.)
Supply Voltage 12-24VDC
Power Consumption 40mA Max
Degree of Protection IP54
NPN Output 100mA
Temperature/Humidity -25 to +55degC/ 35 to 85%RH
Price Each
PES-006 Photo Electric Switch LS18-15MT
Page 86 Ocean Controls Catalog 2009
1
$95.00
5+
less 10%
OCEAN CONTROLS - SENSORS
Laser Photo Electric Switch
Industrial Grade Photo Interrupter
Model: LAS-T18NO20MD
Specification:
•
Type of reflection: T: THROUGH
BEAM
•
Mounting distance Sn: 10cm-20m
•
Out type: NPN (NO+NC)
•
Supply voltage (DC):10-30 V DC
•
Voltage drop:<=0.8V
•
Rated insulation voltage: >=20MΩ
•
Load current (DC/AC):100mA
•
Max.Off-state current (NPN/PNP): <=5mA
•
Leak current: <=20µA
•
Response time: THROUGH BEAM: <1ms
•
Working angle (T/R): <3º
•
Difference distance: <0.1%
•
Function indication: Red LED Display
•
Detect mode: Red laser (640-655nM)
•
Ambient light: Incandescence lamp: 3000Lx / Sun light 10000Lx
•
IP rating (IEC60529): IP67
•
Housing material: Nickle plated brass
•
Connection mode: Wire cable
•
Cable length (Standard): 2m
•
Ambient temperature: -25...+55ºC
Price Each
1
IBL-001 IBEST Laser Photo Sensor LAS-T18NO20MD $75.00
5+
less10%
1
$29.00
5+
less10%
Hall Effect Sensors
Features:
•
•
•
•
•
Standard sensing object: magnetic objects.
Fast response, long operation life.
Mini volume, easy to be installed, in particular installed closely inside metal objects in
line, can detect magnetic objects through
metal objects.
IP ratings: IP67, water and oil resistant.
Widely used in pneumatic, liquid, plunger pump, bicycle
pump...etc for detecting and positioning purpose.
Can detect magnetic objects through metal objects
Flush Mounting
It is available in the size of M12 and M18.
This device enables you to turn off a circuit on
and off optically. It consists of an IR LED facing a phototransistor across and air gap. Any
object in the gap will interrupt the IR beam and
consequently switch the phototransistor on and
off. The device is very fast and ideal for counting, timing or sensing.
Price Each
IBP-006 Hall Sensor M12 NPN Output
IBP-007 Hall Sensor M18 NPN Output
1
$27.50
$29.50
5+
less10%
less10%
S40 Analog Proximity Sensor
Block Measures 25Lx5Wx13H
Gap measure 3mm,
Mounting Holes 3.2mm Dia
1
$5.50
5+
less10%
M30*1.5 Analog Proximity Sensor
Features
- Diension:M30*1.5
- Installation:Non-Flush(unshielded)
- Mounting distance Sn:15mm
- Detect distance Sa:1.5...15mm
- Detect Object(Q235 steel) mm:18*18*1t
- Supply Voltage:DC15-30V
- Current Consumption:<=20mA
- Output Current(I):4-20mA
- Output Voltage(V):0-5V OR 0-10V
- Load Resistance(Current/Voltage):300Ω/1K
- Max.Fluctuant Voltage:<=5%
- Ambient Temperature:-25...+70°C
- Detect Status:Red LED Indicator
- IP Rating(IES60529):IP67
- Housing Material:Nickle plated brass
Price Each
1
IBP-020 M30 analog proximity sensor, 4-20mA output $39.00
IBP-021 M30 analog proximity sensor, 0-10mA output $39.00
Page 87 Ocean Controls Catalog 2009
Price Each
PES-011 Photo Interrupter Switch PU-08
•
•
PCB or Chassis Mount Photo Interrupter
Price Each
PES-010 Photo Interrupter Component Switch
This Photo Interrupter is suited for Industrial
Use. Fully sealed it is easily mounted with 2
supplied screws. Features are
Supply Voltage 12-24VDC
Current Consumption 18mA Max
Frequency of Response 2KHz
Output NPN Transistor 100mA MAX
Degree of Protection IP66
Temperature/Humidity -25 to +55degC/ 35 to 85%RH
Measures 55mm x 30mm x 14mm
Features
- Diension:S40
- Installation:Flush(shielded)
- Mounting distance Sn:20mm
- Detect distance Sa:0.1...20mm
- Detect Object(Q235 steel) mm:18*18*1t
- Supply Voltage:DC15-30V
- Current Consumption:<=20mA
- Output Current(I):4-20mA
- Output Voltage(V):0-5V OR 0-10V
- Load Resistance(Current/Voltage):300Ω/1K
- Max.Fluctuant Voltage:<=5%
- Ambient Temperature:-25...+70°C
- Detect Status:Red LED Indicator
- IP Rating(IES60529):IP67
- Housing Material:ABS
Price Each
1
IBP-022 S40 analog proximity sensor, 4-20mA output $49.00
IBP-023 S40 analog proximity sensor, 0-10mA output $49.00
5+
less10%
less10%
5+
less10%
less10%
OCEAN CONTROLS - SENSORS
PCB or Chassis Mount Photo Interrupter
Industrial Grade Photo Interrupter
This device enables you to turn off a circuit on
and off optically. It consists of an IR LED facing a phototransistor across and air gap. Any
object in the gap will interrupt the IR beam and
consequently switch the phototransistor on and
off. The device is very fast and ideal for counting, timing or sensing.
This Photo Interrupter is suited for Industrial
Use. Fully sealed it is easily mounted with 2
supplied screws. Features are
Supply Voltage 12-24VDC
Current Consumption 18mA Max
Frequency of Response 2KHz
Output NPN Transistor 100mA MAX
Degree of Protection IP66
Temperature/Humidity -25 to +55degC/ 35 to 85%RH
Measures 55mm x 30mm x 14mm
Price Each
PES-011 Photo Interrupter Switch PU-08
1
$29.00
Block Measures 25Lx5Wx13H
Gap measure 3mm,
Mounting Holes 3.2mm Dia
5+
less10%
Ultrasonic Range Finder
Specifications and Features
- Small and light: 0.870" x 0.785" x 0.645", 4.3 grams
- Long range detection: 0 - 254 inches (6.45 meters)
- No deadband (detections from 0 to 6 inches are output as 6 inches)
- 1-inch resolution
- Low typical current consumption: 2 mA
- Runs on 5 V +/- 0.5 V
- 42 kHz ultrasonic sensor, 20 Hz reading rate
- Free-run or triggered operation
1
$47.50
$47.50
5+
less 10%
less 10%
Infrared Range Finder
Page 88 Ocean Controls Catalog 2009
5+
less10%
Description: This is the new, weather resistant, field-hardened WR1 from Maxbotix.
The WR1 uses a robust PVC housing, is
designed to meet IP67 water intrusion, and
matches standard electrical 3/4" PVC pipe
fittings. We are extremely pleased with the
size, quality, and ease of use of this low
voltage weather-resistant range finder. The
serial interface is a bit odd (it's RS232
instead of standard TTL), but the PWM and
Analog interfaces will allow any micro to
listen easily enough. The sensor provides
very accurate readings of 0 to 254 inches (0 to 6.45m) in 1 inch increments with little or no dead zone!
Features:
* 42kHz Ultrasonic sensor
* Operates from 3-5.5V
* Low 2.1mA supply current
* 20Hz reading rate
* RS232 Serial Output - 9600bps
* Analog Output - (Vcc/512)/inch
* PWM Output - 147uS/inch
* Designed for outdoor application
Price Each
SFG-002 Ultrasonic Range Finder - Maxbotix LV-WR1
1
$179.95
Lever Actuated Microswitch
Infrared proximity sensor
made by Sharp. Part #
GP2Y0A02YK0F has an
analog output that varies from 2.8V
at 15cm to 0.4V at 150cm with a supply
voltage between 4.5 and 5.5VDC. The
sensor has a Japanese Solderless Terminal (JST) Connector. We recommend
using a JST pigtail or soldering wires directly to the back of the module. This sensor is great for sensing objects up to 5 feet away!
Price Each
IRP-001 Infrared Proximity Sensor Long Range
1
$5.50
Ultrasonic Range Finder - Maxbotix LV-WR1
The MaxSonar-EZ0 and EZ1 are sonar
range finders that offer very short- to
long-range detection and ranging in an
incredibly small package with ultra-low
power consumption. The MaxSonar detects objects from 0 inches to 254 inches
(6.45 meters) and provides sonar range
information from 6 inches out to 254
inches with 1-inch resolution. Objects
between 0 inches and 6 inches range as 6 inches. The interface output
formats included are pulse width output, analog voltage output, and
asynchronous serial digital output. The LV-MaxSonar-EZ0 differs from
the LV-MaxSonar-EZ1 in beam shape and sensitivity; the EZ0 has the
most sensitivity of the MaxSonar product line, yielding a controlled wide
beam with high sensitivity.
Price Each
POL-723 Ultrasonic Range Finder -EZ0
POL-725 Ultrasonic Range Finder -EZ1
Price Each
PES-010 Photo Interrupter Component Switch
1
$29.95
5+
less 10%
Specifications:
Switch Type: SPDT Momentary
Contact Rating: 6A @ 250V AC
Contact Resistance: <15mR
Actuator Length: 27mm
Long Lever Length:51mm
Price Each
LSW-001 Lever Acuated Microswitch
LSW-002 Long Lever Acuated Microswitch
1
$3.27
$3.27
5+
less10%
less10%
OCEAN CONTROLS - SENSORS
PIR Motion Sensor
Float Switch
This is a simple to use motion sensor. Power it
up and wait 1-2 seconds for the sensor to get a
snapshot of the still room. If anything moves
after that period, the 'alarm' pin will go low.
Red wire is power (5 to 12V). Brown wire is
GND. Black wire is open collector Alarm.
This unit works great from 5 to 12V (datasheet
shows 12V). You can also install a jumper wire
past the 5V regulator on board to make this unit work at 3.3V. Sensor
uses 1.6mA@3.3V.
The alarm pin is an open collector meaning you will need a pull up resistor on the alarm pin. The open drain setup allows multiple motion
sensors to be connected on a single input pin. If any of the motion sensors go off, the input pin will be pulled low.
Price Each
PIR-001
PIR Motion Detector
1
$14.95
+5
less 10%
PIR Motion Sensor
Specifications:
Switch type: SPST
Switching current: 0.5A DC
Contact rating 1.5A @ 200VDC (Max)
Contact resistance: 100m?
Insulation restistance: >10^10 ?
Magnetic sensitivity: 20 - 50 AT
Operate time: 0.8ms
Flying lead length: 300mm
Temperature Rating: -30 to 147 degrees C
Price Each
LSW-010 Horizontal Mount Float Switch
LSW-011 Vertical Mount Float Switch
Essential for installations of industrial or lab equipment. Latching actuator with rotating release and normally closed contacts. When the actuator is pushed in, the contacts open and the switch is latched, ensuring
the equipment can't be operated until the switch is intentionally disengaged by rotating the actuator and releasing. It
has two independent sets of contacts so the neutral and active may be both isolated.
Vertical range is adjustable and a high quality
noise reduction circuit ensures reliable detection.
Superior RFI/EMI immunity.
Specifications:
• Configuration: 2 contact sets, normally closed
(RED) & normally open (GREEN)
• Actuation: Push off, rotate on
• Contact rating: 125VAC 6A, 300VAC 3A
• Mounting hole: 22mm
Specifications:
Power supply: 9-16V
Current drain: NO 8mA @ 12V DC
Alarm period: 1.5-2.5 sec
Alarm output: NC/NO, 30VDC, 0.2A
Pulse4 count: 2/3 selectable
RFI immunity: 25V/m average
Tamper: NC, open trigger
Temperature range: -20 degree's C to 60 degrees C
Dimensions: 100 x 60 x 42mm
Price Each
LSW-020 Latching Emergency Stop Switch
1
$9.95
Beambar Security Sensor
1
$31.32
The Beambar 4 is a multiple infrared
Beam device for short range internal use.
Four time multiplexed beams are arranged
with a separation of 75mm, an alarm being generated if two adjacent beams are
broken. Its unique expansion capability
allows a complete barrier of almost limitless height to be formed by stacking units
together. Such a barrier provides a tightly
controlled detection area with a very high
probability of detection. The Beambar 4 is housed in a white ABS box
300mm long x 44mm wide x 254mm deep, allowing a very compact and
attractive installation. Additional fixings are provided which permit a wide
range of installation options. Installation is facilitated by the provision of
several features such as test LEDs for each beam, automatic gain reduction during installation, and environmental outputs are provided
which will warn of impending problems.
Price Each
NET-040 Beam Bar 4
Page 89 Ocean Controls Catalog 2009
1
$29.23
$20.86
Latching Emergency Stop Switch
Easy to install PIR with dual look down detection.
Features excellent temperature compensation and
selectable pulse count. Its stylish countoured shape
virtually disappears once installed into the corner of
any room.
Price Each
PIR-005 PIR Motion Detector
Fully immersible. Ideal for water tank systems
such as rain or waste water management,
activating boat bilge pumps etc. Can be used
to control pumps or electric valves when liquid
levels change. Features a waterproof membrane which mounts on the inside of the tank.
1
$59.00
OCEAN CONTROLS - SENSORS
Temperature and Humidity Transmitter Wall Mount
Temperature and Humidity Transmitter Duct Mount
The Relative Humidity and Temperature Transmitters RHT-DM are microprocessed based instruments that incorporate high accurate and
stable sensors whose information is converted to linear 4-20 mA.
The transmitter parameters can be configured to tailor a particular application.
Specifications
Loop powered 4-20 mA outputs.
Power supply: 12 to 30 Vdc
Channel isolation: the 4-20 mA outputs are isolated from each other.
Reverse polarity protection: YES.
Cable entrance: compress fitting PG7.
Operating limits:
Sensor and probe (RHT-DM): -20 to 80 °C, 0 to 100 %RH.
Electronic circuit: -10 to +65 °C, 0 to 95 %RH.
RH channel:
Accuracy: ±1,5 %RH @ 25 °C, from 20 to 80 %RH.
Repeatability: ±1% RH.
Hysteresis: ±1% RH.
Span: any value between 0
and 100% RH or –40 to 100°C
for dew point.
Temperature channel:
Accuracy: ±0,5 °C @ 25 °C.
Maximum ±2 °C from -40 to
80 °C.
Repeatability: ±0.1°C.
Span: between -40 and 120°C.
The Relative Humidity and Temperature Transmitters RHT-DM are microprocessed based instruments that incorporate high accurate and
stable sensors whose information is converted to linear 4-20 mA. They
are suitable for mounting in air conditioning ducts
Using the digital communication interface, the transmitter parameters
can be configured to tailor a particular application.
Specifications
Loop powered 4-20 mA outputs.
Power supply: 12 to 30 Vdc
Operating limits:
Sensor and probe (RHT-DM): -20
to 80 °C, 0 to 100 %RH.
Electronic circuit: -10 to +65 °C, 0
to 95 %RH.
RH channel:
Accuracy: ±1,5 %RH @ 25 °C, from 20 to 80 %RH.
Repeatability: ±1% RH.
Hysteresis: ±1% RH.
Span: any value between 0 and 100% RH or –40 to 100°C
Price Each
________ 1
RHT-003 Temperature and Humidity Sensor 4-20mA output
$209.00
RHT-006 Temperature and Humidity Sensor 0-10V output
$209.00
Temperature Transmitter Wall Mount
The Relative Humidity and Temperature Transmitters Temp-DM are
microprocessed based instruments that incorporate high accurate and
stable sensors whose information is converted to linear 4-20 mA.
The transmitter parameters can be configured to tailor a particular application.
Specifications
Temperature:
Accuracy: 0,5 °C @ 25 °C.
Repeatibility: ±0,1 °C.
Range: programmable between -50 and 120 °C
(please check operational limits).
Response Time: up to 30 s in fairly still air.
- Operational limits:
Electronic module(WM-DM): -20 to +65 °C, 0 to
95% RH;
Sensor and Probe (DM): -40 to +100 °C.
Note: When measuring temperatures higher than
+65 °C or lower than -20 °C, only 50% of the probe
total length must be inserted into the measured
environment.
Power:
- 12 to 30 Vdc (model 4-20 mA);
- 18 to 30 Vdc (model 0-10 V). Cable input: PG7 cable
gland.
Output:
- Two-wire loop powered 4-20 mA or 20-4 mA.
- Voltage output: 0-10 Vdc or 10-0 Vdc (optional).
Price Each
________ 1
RHT-020 TEMP-WM TemperatureSensor 4-20mA output
$135.00
RHT-021 TEMP-WM TemperatureSensor 0-10V output
$135.00
RHT-022 TEMP-DM Duct Temp Sensor 4-20mA 150mm
$155.00
RHT-024 TEMP-DM Duct Temp Sensor 4-20mA 250mm
$159.00
RHT-030 Dust Covers for RHT-WM Probes
$10.00
Price Each
LAJ-003 Temperature Probe
LAJ-006 Stainless Steel Temperature Probe
Page 90 Ocean Controls Catalog 2009
1
$65.00
$99.00
Price Each
________
RHT-004 Duct Temp and Humidity Sensor 4-20mA 150mm Probe
RHT-005 Duct Temp and Humidity Sensor 4-20mA 250mm Probe
1
$225.00
$225.00
Temperature and Humidity Transmitter - RHT MODBUS
The RHT-WM-485-LCD and RHT-DM-485-LCD transmitters include high
precision and stability sensors for measuring temperature and relative
humidity. They are microprocessed devices and, therefore, allow being
entirely configured through a RS485 interface, using the Modbus RTU
commands. The DigiConfig allows the configuration of all transmitter
features as well as its diagnostic procedure.
Specifications
* Operating temperature of the transmitter: From 0 °
C to 70 °C
*Electromagnetic compatibility: EM 61326:2000
*Sensor measuring range
Temperature: –40.0 °C to 100.0 °C
Relative Humidity (RH): 0.0 to 100.0 % RH (No
Condensing)
Dew Point: –40.0 °C and 100.0 °C
* Measuring resolution
Temperature: 0.1 °C. 14 bits (16383 levels)
Relative Humidity (RH): 0.1 %. 12 bits (4095 levels)
* Response time
Temperature: up to 30s in slow air movement
Humidity: up to 8s in smooth air movement (20 to 80 % RH)
* Sampling interval: 3 seconds
* Power supply: 12 Vdc to 30 Vdc
* Case: Polycarbonate
* Protection class: Product appropriate for applications which require
protection class up to IP65
* Electronic module case: IP65; Sensor capsule: IP40
Price Each
RHT-010 RHT MODBUS
1
$225.00
Temperature Probes
An inexpensive and easy to use temperature
probe. Designed to work with a LabJack, but
can also be used with any voltage measuring
device. Outputs 10 mV per degree C, and has
a range of -40 to +100 degrees C.
A stainless steel easy to use, very accurate, and
waterproof temperature probe The sensor is
mounted in a stainless steel sheath and features a
high-level linear output of 10 mV per degree F,
5+
typical accuracy of +/-0.25 degrees C ( +/-0.4
less 10%
degrees F) at room temperature, and a range of
less 10%
0 to +300 degrees F (-17 to +150 degrees C).
OCEAN CONTROLS - SENSORS
GS-4200 Pressure Sensors
The Ellison Sensors GS4200 series pressure
transmitter is designed for demanding applications where reliable pressure measurement
is required and where good quality, fast delivery and low cost are high priority.
The GS4200 is the latest addition to the Ellison Sensors range, offering outstanding performance due to a unique “Silicon On Sapphire” diaphragm construction giving excellent
stability over a wide temperature range. Accuracy of +/-0.25% with an over pressure limit of
twice nominal pressure, together with an output of 4-20mA, wide operating temp range –40 to +80degC and adjustable zero & span for ease of
calibration. All models are supplied with ¼” BSP thread process connection and a large DIN43650 Plug for electrical connection. The titanium
pressure ports and stainless steel body offer high level of corrosion
resistance with the overall transducer having an IP65 environmental
rating.
Price Each
PRT-001 Ellison GS4200 -1 to 0 Bar Vacuum
PRT-002 Ellison GS4200 0 to 500 mBar (50KPa, 7.3PSI)
PRT-003 Ellison GS4200 0 to 1 Bar (100KPa, 14.7PSI)
PRT-004 Ellison GS4200 0 to 1.6 Bar (160KPa, 23PSI)
PRT-005 Ellison GS4200 0 to 2.5 Bar (250KPa, 36PSI)
PRT-006 Ellison GS4200 0 to 4 Bar (400KPa, 58PSI)
PRT-007 Ellison GS4200 0 to 6 Bar (600KPa, 86PSI)
PRT-008 Ellison GS4200 0 to 10 Bar (1MPa, 147PSI)
PRT-009 Ellison GS4200 0 to 16 Bar (1.6MPa, 230PSI)
PRT-010 Ellison GS4200 0 to 25 Bar (2.5MPa, 360PSI)
PRT-011 Ellison GS4200 0 to 40 Bar (4.0MPa, 580PSI)
PRT-012 Ellison GS4200 0 to 60 Bar (6.0MPa, 860PSI)
PRT-013 Ellison GS4200 0 to 100 Bar (10MPa, 1470PSI)
PRT-014 Ellison GS4200 0 to 160 Bar (16MPa, 2300PSI)
PRT-015 Ellison GS4200 0 to 250 Bar (25MPa, 3600PSI)
PRT-016 Ellison GS4200 0 to 400 Bar (40MPa, 5800PSI)
PRT-017 Ellison GS4200 0 to 600 Bar (60MPa, 8600PSI)
PRT-018 Ellison GS4200 0 to 1000 Bar (100MPa)
PRT-019 Ellison GS4200 0 to 1500 Bar (150MPa)
1
$459.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
$399.00
Price Each
PRT-035 Ellison PR3850 0 to 2.5 Bar (250KPa, 36PSI)
PRT-036 Ellison PR3850 0 to 4 Bar (400KPa, 58PSI)
PRT-037 Ellison PR3850 0 to 6 Bar (600KPa, 86PSI)
PRT-038 Ellison PR3850 0 to 10 Bar (1MPa, 147PSI)
PRT-039 Ellison PR3850 0 to 16 Bar (1.6MPa, 230PSI)
PRT-040 Ellison PR3850 0 to 25 Bar (2.5MPa, 360PSI)
PRT-041 Ellison PR3850 0 to 40 Bar (4.0MPa, 580PSI)
PRT-042 Ellison PR3850 0 to 60 Bar (6.0MPa, 860PSI)
PRT-043 Ellison PR3850 0 to 100 Bar (10MPa, 1470PSI)
PRT-044 Ellison PR3850 0 to 160 Bar (16MPa, 2300PSI)
PRT-045 Ellison PR3850 0 to 250 Bar (25MPa, 3600PSI)
PRT-046 Ellison PR3850 0 to 400 Bar (40MPa, 5800PSI)
PRT-047 Ellison PR3850 0 to 600 Bar (60MPa, 8600PSI)
PRT-048 Ellison PR3850 0 to 1000 Bar (100MPa)
PRT-049 Ellison PR3850 0 to 1500 Bar (150MPa)
1
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
$485.00
PR-3850 Pressure Sensors with Flush Diaphragm
The Ellison Sensors PR3850 series flush
diaphragm pressure transmitter is designed
for demanding applications where the process media is unsuitable for direct contact with
the transducer diaphragm (slurries etc).
The series features high accuracy together
with an output of 4-20mA and adjustable zero
& span for ease of calibration. All models are
supplied with ½" BSP thread process connection (optional 1" BSP) and a large
DIN43650 Plug for electrical connection. The
fully 316 stainless steel body offer high level
of corrosion resistance with the overall transducer having an IP65 environmental rating. Other features include can operate in ambient temperature of –40 to +90degC and media temperature of –20 to +85degC
Applications for the PR3850 series include the continuous monitoring of
SCP1000 Barometric Pressure Board
PM1000 Plug In Transducer Display
The PM1000 Series is universal plug-on LED
display suitable for use with various transmitters having a 4-20mA output and fitted with
DIN43650 connector. The Plug in display simply fits between the plug and socket on any
DIN43650 connector, it is supplied from the 420mA current loop signal of the transmitter. No
additional power is required. The unit is user
programmable from two buttons behind the
front panel enabling scaling, decimal point position and adjustment of the set point position. All
are easily set through the menu steps outputted
to the LED display and stored in an EEPROM,
the programme is not lost in the event of power
failure. The display can be rotated through 90
degree steps for use in different installation
positions. The integral open-collector output on
the PM1001 model allows the transmitter to be
retrofitted easily with a limit contact set point,
for use as an alarm or controller. Intrinsically safe models available
certified to EEx ib IIC T4
Price Each
PRT-050 3.5 Digit LED Plug-On Display
PRT-051 3.5 Digit LED Plug-On Display with alarm point
Page 91 Ocean Controls Catalog 2009
1
$299.00
$399.00
Please note: This is the ASIC rev B (IC label
'P01'). The SCP1000 is the very first absolute
pressure sensor on the market to use MEMs
technology to grant 17-bit resolution. Under
ideal conditions, this sensor can detect the
pressure difference within a 9cm column of air.
VTI's SCP1000-D01 digital absolute pressure
sensors are intended for barometric pressure measurement and altimeter applications for 30kPa...120kPa and -20°C...70°C measuring ranges.
The pressure and temperature output data is calibrated and compensated internally and the communication between the SCP1000 and its
host micro-controller is realized using an SPI interface.
Four user selectable measuring modes combine 17-bit resolution (9cm
of air column) with low or ultra-low power consumption, or alternatively
15-bit resolution (18cm of air column) with high speed data read (9Hz) or
less than 5µA and power consumption. For example, at Low Power
mode, the SCP1000 has an overall resolution of 2 Pa (15cm of air column) and a power consumption of 3.5µA.
This unit comes in a newly developed RoHS compliant plastic housing.
Normal hot-air rework will destroy this sensor so we highly recommend
this breakout board for prototyping.
- 3V single supply operation
Price Each
BPS-001 SCP-1000 Barometric Pressure Sensor
1
5+
$69.95 less 10%
OCEAN CONTROLS - SENSORS
Pressure Transmitters NP-430A Series
ECONOMIC TYPE VACUUM / PRESSURE SENSOR BPS Series
NP-430A Pressure Transmitter
A great economical pressure sensor! The
NP-430A series of pressure transmitters have
been developed for general industrial applications including refrigeration technology. It can
be used with most general purpose gases and
liquids but is NOT compatible with ammonia.
Features include
- Pressure Ranges: 0 to 2 bar and 0 to 120 bar
- Signal output: two-wire 4-20 mA
- Power supply (V): 12 to 28 Vdc
- Load (RL): RLmax = (V - 12 V) / 20 mA
- Accuracy: better than 1% FS (including linearity, hysteresis and repeatability)
- Long-term stability: 0.4 % / FS / year
- Over load: 150 % FS
- Rupture pressure: 300% FS
- Electrical connection: Packard Type
- Protection: IP67
- Weight: 90 g
- Ambient Temperature: -40 to 80 °C
- Process fluid temperature: -40 to 100 °C
- Response time: < 10 ms (0 to 99%)
- Process connection: External thread ¼ “- 18 NPT (basic model)
- Wetted parts: Stainless Steel 1Cr18Ni9Ti, Ceramic Diaphragm (Al2O3
- 96%)
- Sealing material: Nitrile NBR O’ring
Price Each
NPT-002 NP430A Relative Pressure Sensor 0-2 bar
NPT-005 NP430A Relative Pressure Sensor 0-5 bar
NPT-010 NP430A Relative Pressure Sensor 0-10 bar
NPT-020 NP430A Relative Pressure Sensor 0-20 bar
NPT-030 NP430A Relative Pressure Sensor 0-30 bar
NPT-060 NP430A Relative Pressure Sensor 0-60 bar
NPT-120 NP430A Relative Pressure Sensor 0-120 bar
Page 92 Ocean Controls Catalog 2009
1
$149.00
$149.00
$149.00
$149.00
$149.00
$149.00
$149.00
Features:
*Accuracy: ± 0.5% F.S.
*Measuring range: 10, 100, 250 bar
*Measuring absolute or gauge pressure
*Standard and custom options available for
OEM design
*Robust package, all laser-welded stainless
steel design
*Power supply: DC8~30V; Output: 4~20mAdc
*Proof pressure range: 3 x Full Scale
*Compact size and excellent
Specification:
*Accuracy: ±0.5% F.S.
*Thermal Error: <0.5% F.S.
*Total Error: <0.5% F.S.
*Stability: <0.25% F.S. / Year
*Zero Pressure Offset: 4 mAdc
*Full Scale Output: 20 mAdc
*Proof Pressure: 3 x F.S.
*Burst Pressure: Absolute Pressure: 10 x F.S. or 15000 psi; Gauge
Pressure: 5 x F.S.
*Pressure Cycles: 8Hz
*Response Time: <1 msec
*Vibration: 10 to 2050Hz, 20 sinusoidal, 3 axes
*Thermal Shock: -40 to 105°C, 0.5hr soaks at Temp.
*Temperature Coefficient: 100ppm/°C (0 to 60 °C)
*Operating Temperature: -40 to 105°C
*Operating Humidity: <95% RH (non-condensing)
*Storage Temperature: -40 to 105°C
*Storage Humidity: <95% RH (non-condensing)
*Power Supply: DC 18 to 30V (2 wire loop)
*EMC Compatibility: 80 MHz to 1 GHz
*Wetted materials: 304L & 316L stainless steel
*Pressure Connection: 1/4" NPT
*Electrical Connection: DIN 43650
Price Each
ALT-106 Pressure Sensor Input:0-6 Bar
ALT-110 Pressure Sensor Input:0-10 Bar
ALT-125 Pressure Sensor Inout:0-25 Bar
ALT-140 Pressure Sensor Input:0-40 Bar
ALT-200 Pressure Sensor Input:0-100Bar
1
$229.00
$229.00
$229.00
$229.00
$229.00
OCEAN CONTROLS - SENSORS
Barometric Pressure Board - HP03D
The The HP03D is a high accuracy, lowcost pressure sensor, ideal for use with
weather stations, altimeters and pressure
measurement. The unit comprises a piezo
resistive pressure sensor and a 16 bit ADC
with 15-Bit accuracy together with a measurement accuracy of 0.5hpa. Easy to interface to any microcontroller with a standard
I²C interface. The unit requires only 3V and
full installation instructions are available in the datasheet link below.
Features
• Pressure Range 300-1100hpa
• 16 Bit ADC
• I²C Serial Interface
• Accurate to 0.5hpa
• Supply Voltage: 2.2 - 3.6V
Accelerometer Breakout Board - ADXL202JE +/-2g
Breakout board for the Analog Devices accelerometers in the E8 package. The ADXL is a
solid state MEMS accelerometer with digital
PWM or Analog output. The ADXL can measure both static and dynamic acceleration.
This means the ADXL is suited well for sensing tilt (used in many Glove / Air Mouse applications) and for sensing brute acceleration
(rocketry and general motion sensing applications).
Board comes fully assembled and tested with selected sensor, 0.1uF
filtering capacitors, and 1MOhm pulse width resistor (where required).
Installed Sensor: ADXL202 +/-2g (PWM and Analog)
Price Each
BPS-010 Barometric Pressure Sensor HP03D
1
5+
$27.50 less 10%
Price Each
ACC-001 Accelerometer Board - ADXL202JE +/-2g
1
5+
$59.00 less 10%
Accelerometer Breakout Board Breakout board for the Analog Devices accelerometers in the E8 package. The ADXL is a
solid state MEMS accelerometer with digital
PWM or Analog output. The ADXL can measure both static and dynamic acceleration. This
means the ADXL is suited well for sensing tilt
(used in many Glove / Air Mouse applications)
and for sensing brute acceleration (rocketry and
general motion sensing applications).
Board comes fully assembled and tested with selected sensor, 0.1uF
filtering capacitors, and 1MOhm pulse width resistor (where required).
Installed Sensor: ADXL210 +/-10g (PWM and Analog)
Price Each
ACC-002 Accelerometer Board - ADXL210AE +/-10g
1
5+
$59.00 less 10%
Accelerometer Breakout Board - ADXL322 +/-2g
Breakout board for the dual axis ADXL32x
accelerometers. Brings out the analog voltage levels from the X and Y axis to a standard .1" header. The ADXL320 can be powered from 2.4V-5.25V. The Self-Test pin
can be used to verify sensor operation.
Board comes fully assembled and tested
with selected sensor and 0.1uF filtering
capacitors.
Installed Sensor: ADXL322 (+/- 2g)
Dimensions: 18x18 mm (0.70x0.70")
Price Each
ACC-005 Accelerometer Board - ADXL322 +/-2g
1
5+
$35.95 less 10%
Accelerometer Breakout Board - ADXL320 +/-5g
Tri Axis Accelerometer - MMA7260Q
Breakout board for the dual axis ADXL32x
accelerometers. Brings out the analog voltage levels from the X and Y axis to a standard .1" header. The ADXL320 can be
powered from 2.4V-5.25V. The Self-Test
pin can be used to verify sensor operation.
Breakout board for the 3 axis MMA7260Q
accelerometer from Freescale. Please view
the datasheet for this impressive sensor!
With a low power shut-down mode, high
sensitivity output with selectable ranges
(+/- 1.5, 2, 4, and 6g), this sensor is one of
the very first to market with three accelerometers sensors built onto a single IC!
Board comes fully assembled and tested
with external filters installed.)
Board comes fully assembled and tested
with selected sensor and 0.1uF filtering
capacitors.
Installed Sensor: ADXL320 (+/- 5g)
Dimensions: 18x18 mm (0.70x0.70")
Price Each
ACC-006 Accelerometer Board - ADXL320 +/-5g
ACC-007 Accelerometer Board - ADXL321 +/-18g 5g
Page 93 Ocean Controls Catalog 2009
Dimensions: 25x25 mm (1x1")
1
5+
$35.95 less 10%
$35.95 less 10%
Price Each
ACC-020 Accelerometer Board - MMA7260Q
1
$24.95
5+
less 10%
OCEAN CONTROLS - SENSORS
Tri Axis Accelerometer - LIS3LV02DQ
Breakout board for the 3 axis
LIS3LV02DQ accelerometer from ST
Micro. With a digital interface (SPI or
I2C), the user only has to initiate commands to get 1mg resolution! Independent channels can be shut off, the sensor
can be powered down, even an interrupt
threshold can be set and used to awaken
the sensor from power down! Selectable
ranges are available for +/-2g and 6g.
This sensor is one of the first with triple axis and an easy to use
digital interface. Board comes fully assembled and tested with
external decoupling caps.
We were thoroughly impressed with the flexibility and precision
of this sensor. This is a great sensor to play with if you need
triple axis accelerations in digital form and you don't want to deal
with analog conversions or filtering.
Dimensions: 21x23mm (0.8x0.9")
Price Each
ACC-021 Accelerometer Board - MMA7260Q
1
$52.50
5+
less10%
Triple Axis Accelerometer Breakout ADXL335
Description: Breakout board for the 3 axis
ADXL335 from Analog Devices. This is
the latest is a long, proven line of Accelerometers from Analog - and now the holy
grail has finally arrived. The ADXL335 is
a triple axis accelerometer with extremely
low noise and power consumption - only
320uA! Sensor ranges from +/-3g. Board
comes fully assembled and tested with
external components installed.
Triple Axis Accelerometer Breakout ADXL345
Breakout board for the Analog Device
ADXL345. The ADXL345 is a small, thin,
low power, 3-axis accelerometer with high
resolution (13-bit) measurement at up to
±16 g. Digital output data is formatted as
16-bit twos complement and is accessible
through either a SPI (3- or 4-wire) or I2C
digital interface.
The ADXL345 is well suited to measures
the static acceleration of gravity in tilt-sensing applications, as
well as dynamic acceleration resulting from motion or shock. Its
high resolution (4 mg/LSB) enables measurement of inclination
changes less than 1.0°.
Several special sensing functions are provided. Activity and
inactivity sensing detect the presence or lack of motion and if
the acceleration on any axis exceeds a user-set level. Tap sensing detects single and double taps. Free-fall sensing detects if
the device is falling. These functions can be mapped to one of
two interrupt output pins. An integrated, patent pending 32-level
first in, first out (FIFO) buffer can be used to store data to minimize host processor intervention. Low power modes enable
intelligent motion-based power management with threshold
sensing and active acceleration measurement at extremely low
power dissipation.
Features:
* 2.0-3.6VDC Supply Voltage
* Ultra Low Power: 40uA in measurement mode, 0.1uA in
standby@ 2.5V
* Tap/Double Tap Detection
* Free-Fall Detection
* SPI and I2C interfaces
Note: The silkscreen indicators for the axises are incorrect.
Please refer to the datasheet for the correct orientation.
Price Each
1
5+
ACC-023 Triple Axis Accelerometer Breakout - ADXL345 $37.27 less 10%
Dimensions: 0.7x0.7"
Price Each
ACC-024 Triple Axis Accelerometer Breakout - ADXL335
Page 94 Ocean Controls Catalog 2009
1
5+
$33.27
OCEAN CONTROLS - SENSORS
Triple Axis Accelerometer Breakout - LIS302DL
This is a compact breakout board for the
LIS302DL. The LIS302DL is a really impressive
little IC. Low cost, digital interface, small footprint,
easy to use, and it has some great features built
in. If all you need is 8-bit resolution, this is the
digital triple axis accelerometer to use.
Price Each
1
5+
ACC-022 Triple Axis Accelerometer Breakout - LIS302DL $29.95 less10%
3 Axis Accelerometer Breakout Board - ADXL330 +/-3g
Breakout board for the 3 axis ADXL330 from
Analog Devices. This is the latest is a long,
proven line of Accelerometers from Analog and now the holy grail has finally arrived. The
ADXL330 is a triple axis accelerometer with
extremely low noise and power consumption only 320uA! Sensor ranges from +/-3g.
Board comes fully assembled and tested with
external components installed. The ADXL330
is a 3V part and outputs an analog voltage for
each of the three outputs. This voltage is in ratio to the measured acceleration and to the supply voltage (ratiometric). You will need some extra
hardware to convert this analog signal to a usable digital one. Luckily,
many uCs have a built in Analog to Digital converter.
Price Each
1
5+
ACC-008 Triple Axis Accelerometer Board - ADXL330 $35.95 less 10%
Dual Axis Gyro Breakout Board
This is the first dual-axis MEMs gyro available on the open market. The
IDG-300 is a 3.3V leadless IC with a smaller profile than other single
axis gyros. Originally designed for image stabilization, the IDG300 dual
axis gyro is now available for the consulting and research markets.
Applications:
* Inertial Measurement Units (IMUs)
* Handheld GPS Navigation Devices
* Radio controlled helicopters
* Toys and game devices
* Robotic and power tools
* Antenna positioning
* Remote control
Features:
* Integrated X- and Y-axis gyro on a single chip
* Factory set full scale range of ±500°/sec
* Low offset voltage
* Integrated low-pass filters
* Integrated reset switches for high-pass filters
* Superior vibration rejection over a wide frequency range
* High cross-axis isolation by design
* 3V single supply operation
* 5000 g shock tolerance
* RoHS Compliant (Completely Lead Free)
The SerAccel outputs real-time accelerations from 9600 to 57600bps using
visible ASCII characters. The SerAccel
is compatible with any RS232 Comm
port in conjunction with any terminal
program (Hyperterminal, VB Programs,
or anything else that can read the comm
port). Works with USB-RS232 converters.
Price Each
1
5+
ACC-010 Serial Accelerometer Tri-Axis v5 - Dongle
$63.95 less 10%
ACC-011 Serial Accelerometer Tri-Axis v5 - Enclosed $77.95 less 10%
1
$69.95
The ADXRS MEMs gyroscope from
Analog Devices come in 2 forms.
The ADXRS150 150degs/sec and
the ADXRS300 300 degs/sec.
The BGA package has hindered
users for long enough. You can
now use gyroscope rate sensing in
your own projects with this miniature breakout board from Spark Fun
Electronics.
Units come fully populated and tested with an empty 0.1" spaced footprint ready for a straight header, right angle header (recommended), or
your own wires/umbilical cable.
Dimensions: 18x18mm ( 0.70"x0.70")
Weight: 1.1g without header
Price Each
GYR-005 Gyro Breakout Board - ADXRS150
GYR-007 Gyro Breakout Board - ADXRS300
1
5+
$99.95 less 10%
$109.00 less 10%
Magnetic Sensor
This is a simple evaluation board for the
HMC1052L magnetic sensor. The MOSFET
reset and amplifier circuitry are all on board. All
you need is a sensitive ADC and a logic pin for
the reset control and you can get magnetic
heading! No external circuitry required. We
recommend at least a 16-bit ADC to get as
much resolution as possible.
Dimensions: 18x18 mm (0.70x0.70")
Page 95 Ocean Controls Catalog 2009
The SerAccel v5 is a 3 axis accelerometer up to +/-6g with a simple serial interface. The latest SerAccel development, version 5 has many new
improvements including variable baud rate, a factory reset command,
and a complete triple axis measurement system based on the newly
released MMA7260Q sensor from Freescale. Power is gained from any
RS232 port (including USB-to-RS232
converters) so no external power supply
is needed. The onboard PIC (16LF88)
runs at 10MHz and outputs three different types of outputs including calculated,
binary, and raw outputs. The SerAccel
v5 has software configurable settings to
select between 4 sensing ranges (+/1.5, 2, 4, and 6g), as well as a software
selectable measurement frequency (0590Hz).
Gyro Breakout Board - ADXRS150 and ADXRS300
Installed Sensor: ADXL330 (+/- 3g)
Dimensions: 18x18 mm (0.70x0.70")
Price Each
GYR-001 Dual Axis Gyro board
Serial Accelerometer Tri-Axis v5 - Dongle
Serial Accelerometer Tri-Axis v5 - Enclosed
5+
less 10%
Price Each
MAG-001 HMC1052L Magnetic Sensor Card
1
5+
$39.50 less 10%
OCEAN CONTROLS - SENSORS
IMU 5 Degrees of Freedom
Description: The Inertia Measurement Unit Combo
Board is now available with smaller, better, faster,
and cheaper components! This small PCB board
incorporates the new IDG300 dual-axis gyroscope
and Analog Devices triple axis accelerometer in a
tight footprint. The IMU board uses a standard 0.1"
footprint and includes all outputs from both the
IDG300 Gyro and ADXL330 Accelerometer ICs.
This IMU 5DOF is the latest is a long line of development boards. This
latest version allows an unheard of 5 axis of sensing (Roll, Pitch, X, Y,
Z) in less than 1 square inch, and under 2 grams!
By combining the IDG300 and ADXL330 sensors, the IMU board enables students and hobbyists to easily incorporate roll, pitch, and tilt
measurements into their projects or robots.
Board comes fully assembled and tested. Units come as shown without
headers installed. We recommend right-angle break away headers,
straight pin headers, or wire up your own cable!
Dimensions: 0.75"x0.9" (20x23mm)
Weight: 2g
Price Each
SFG-001 IMU 5 Degrees of Freedom-SEN-00741
1
$135.00
5+
less 10%
Current Sensor ACS712 Breakout
This is a breakout board for the fully integrated Hall Effect based linear
ACS712 current sensor. The sensor gives precise current measurement
for both AC and DC signals. Thick copper conductor and signal traces
allows for survival of the device up to 5 times overcurrent conditions.
The ACS712 outputs an analog voltage output signal that varies linearly
with sensed current. The device requires 5VDC for VCC and a couple of
filter capacitors.
Features:
* x05B (5 Amp) version
* Low noise analog signal path
* Device bandwidth is set via the FILTER pin
* 5us output rise time in response to input current
* 80kHz bandwidth
* 1.5% output error at 25 degrees C
* 1.2mOhm internal conductor resistance
* 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
* 5.0 VDC, single supply operation
* 66 to 185 mV/A output sensitivity
* Output voltage proportional to AC or DC currents
* Factory-trimmed for accuracy
* Extremely stable output offset voltage
* Nearly zero magnetic hysteresis
* Ratiometric output from supply voltage
Price Each
SFC-001 ACS712 Breakout
Real Time Clock Module
1
$12.50
5+
less 10%
PL-D Series Length Sensor
Product Features :
- Can measure the length of cloth, paper plastics, etc.
- Photoelectric output with stable signals and long service life.
- Using Nickel-Zinc alloy, it's weightily and doesn't skid.
- The wheels adopt imported tire latex, endurable to friction.
Specification
Item No.
PL-D2M(Y)
PL-D3M(Y)
Unit
10cm(0.1Y)
1cm(0.01Y)
Output Type
Quadrature
Output Impedance
2.7K
Current Consumption
70MA
Output Current
100MA
Power Supply
12-24V
Price Each
COS-301 PL-D2M 10CM Length Sensor
COS-302 PL-D3M 1CM Length Sensor
1
5+
$165.00 less 10%
$199.00 less 10%
PL-S Series Length Sensor
Product Features :
- Can measure the length of cloth, paper plastics, etc.
- Photoelectric output with stable signals and
long service life.
- Using Nickel-Zinc alloy, it's weightily and
doesn't skid.
- The wheels adopt imported tire latex, endurable to friction.
Product Specifications :
Item No.
PL-S1M(Y) PL-S2M(Y) PL-S3M(Y) PL-S4M
Unit
1M(1Y)
10CM(0.1Y) 1CM(0.1Y) 1MM
Current
25MA
35MA
O/p Current 150MA
100MA
Output Type
Single Phase
Output Impedance
2.7K
Power Supply
12-24V
Price Each
COS-311 PL-S2M 10CM Length Sensor
COS-312 PL-S3M 1CM Length Sensor
COS-313 PL-S4M 1MM Length Sensor
1
5+
$149.00 less 10%
$159.00 less 10%
$169.00 less 10%
Current Sensor ACS712 Low Current Sensor Breakout
This current sensor gives precise current measurement for both AC and DC signals. These are
good sensors for metering and measuring overall
power consumption of systems. The ACS712
current sensor measures up to 5A of DC or AC
current. We added an opamp gain stage for more
sensitive current measurements. By adjusting the
gain (from 4.27 to 47) you can measure very
small currents.
This a custom designed module for the DS1307 Real Time Clock. The
module comes fully assembled and pre-programmed with the current
time (ok, so it's our current time - MST). The included Lithium coin cell
The ACS712 Low Current Sensor Breakout outputs an analog voltage
battery (CR1225 41mAh) will run the module for a minimum of 9 years
that varies linearly with sensed current. To calibrate, first set the output
(17 years typical) without external 5V power. The DS1307 is accessed
offset to the desired level (with zero current on the sense lines, read
via the I2C protocol. We've written a test-bed to program the modules.
output with a DVM). Then with a known current input (a 100mA limited
This test-bed code should give you some insight on how to interface the
supply works well for this), set the output deflection with the gain pot.
module to any microcontroller using our example software I2C and BCD
Sensitivity is then calculated as (Vref - Vdeflect)/(current input).
routines.
Features:
The bandwidth on the ASC712 Low Current Sensor Breakout has been
* Two wire I2C interface
set to 34Hz to reduce noise when using at high gains. The full 80KHz
* Hour : Minutes : Seconds AM/PM
bandwidth that the sensor is capable of can be recovered by removing
* Day Month, Date - Year
C1.
* Leap year compensation
Price Each
1
5+
* Accurate calendar up to year 2100
SFC-002 ACS712 Low Current Sensor Breakout
$23.95 less 10%
* Battery backup included
* 1Hz output pin
1
* 56 Bytes of Non-volatile memory available to user Price Each
SFC-010 Real Time Clock Module
$24.95
Dimensions: 0.75x0.75" (20x20mm)
Page 96 Ocean Controls Catalog 2009
OCEAN CONTROLS - SWITCH MODE POWER SUPPLIES
40W Single Rail Switchmode Supplies
60W Single Rail Switchmode Supplies
These switchmode power supplies are
available in 12VDC and 24VDC are over
voltage protected and current limited
with UL/TUV/CE approvals. Powered
from 85-260VAC they are fitted with
screw terminals. The specifications are
Tolerance +/-1%
Ripple and Noise 100mV
Efficiency >75%
DC adjust range +/-10%
Measurements 129(L)x98(W)x38(H)xmm
Output Current 3.5A(12VDC) 1.8A(24VDC)
2 year warranty
Price Each
PSM-001 40W Power Supply 12VDC
PSM-002 40W Power Supply 24VDC
These switchmode power supplies are
available in 12VDC and 24VDC are over
voltage protected and current limited with
UL/TUV/CE approvals. Powered from 85260VAC they are fitted with screw terminals. The specifications are
Tolerance +/-1%
Ripple and Noise 125mV(12VDC), 150mV
(24VDC)
Efficiency >=80%
DC adjust range +/-10%
Measurements 159(L)x98(W)x38(H)mm
Output Current 5.1A(12VDC) 2.7A(24VDC)
2 year warranty
1
$52.00
$52.00
3+
less 10%
less 10%
100W Single Rail Switchmode supplies
1
$70.00
$70.00
3+
less 10%
less 10%
These switchmode power supplies are
available in 12VDC and 24VDC are over
voltage protected and short circuit and
overload protected with UL/TUV/CE approvals. Powered from 85-260VAC they
are fitted with screw terminals.
The specifications are
Tolerance +/-1%
Ripple and Noise 180mV(12VDC), 240mV(24VDC)
Efficiency >80%
DC adjust range +/-10%
Measurements 199(L)x110(W)x50(H)mm
Output Current 12.5A(12VDC) 6.5A(24VDC)
2 year warranty
3+
less 10%
less 10%
40W Multiple Rail Switchmode Supplies
Price Each
PSM-007 150W Power Supply 12VDC
PSM-008 150W Power Supply 24VDC
1
$84.00
$84.00
3+
less 10%
less 10%
60W Multiple Rail Switchmode Supplies
These 40W Multiple rail supplies incorporate short circuit, over load and over voltage protection with CSA/CE/NRTLC approvals.
Powered from 85-264VAC they are fitted
with screw terminals.
The specifications are
Tolerance +/-2% 5VDC, +/-6% 12VDC and
15VDC
Ripple and Noise 100mV on 5VDC, 120mV on 12VDC and 15VDC
Efficiency 72%
Working Temperature 0-50degC
Measurements 129(L)x98(W)x38(H)xmm
2 year warranty
These 60W Multiple rail supplies incorporate short circuit, over load and over voltage protection with UL/CUL/TUV/CE/TB
approvals. Powered from 85-264VAC they
are fitted with screw terminals.
The specifications are
Tolerance +/-2% 5VDC, +/-6% 12VDC and
15VDC
Ripple and Noise 100mV on 5VDC,
100mV on 12VDC and 15VDC
Efficiency 72%
Working Temperature 0-50degC
Measurements 159(L)x97(W)x38(H)xmm
2 year warranty
Price Each
1
PSM-051 +5VDC/3A, +12V/2A and -5VDC/0.5A
$62.00
PSM-052 +5VDC/3A, +12V/2A and –12VDC/0.5A
$62.00
PSM-053 +5VDC/3A, +15V/1.5A and –15VDC/0.5A $62.00
Price Each
PSM-054 +5VDC/7A, +12V/3.5A and -5VDC/1A
PSM-055 +5VDC/5A, +12V/3.5A and –12VDC/1A
PSM-056 +5VDC/5A, +15V/2A and –15VDC/0.5A
Page 97 Ocean Controls Catalog 2009
1
$58.00
$58.00
150W Single Rail Switchmode supplies
These switchmode power supplies are
available in 12VDC and 24VDC are over
voltage protected and short circuit and
overload protected with UL/TUV/CE
approvals. Powered from 85-260VAC
they are fitted with screw terminals.
The specifications are
Tolerance +/-1%
Ripple and Noise 125mV(12VDC), 150mV(24VDC)
Efficiency >=80%
DC adjust range +/-10%
Measurements 199(L)x98(W)x38(H)mm
Output Current 8.5A(12VDC) 4.5A(24VDC)
1 year warranty
Price Each
PSM-005 100W Power Supply 12VDC
PSM-006 100W Power Supply 24VDC
Price Each
PSM-003 60W Power Supply 12VDC
PSM-004 60W Power Supply 24VDC
3+
less 10%
less 10%
less 10%
1
$70.00
$70.00
$70.00
3+
less 10%
less 10%
less 10%
OCEAN CONTROLS - POWER SUPPLIES, BATTERY CHARGERS
120W Multiple Rail Switchmode Supplies
216W Desktop Battery Charger
Incorporate short circuit, over load and over voltage protection with UL/
CUL/TUV/CE/TB approvals. Powered from 85-264VAC they are fitted
with screw terminals. The specifications are
Tolerance +/-2% 5VDC, +/-6% -5VDC
12VDC and -12VDC
Ripple and Noise 80mV on 5VDC, 120mV
on 12VDC, 150mV on 15VDC
Efficiency >75%
Working Temperature 0-50degC
Measurements 199(L)x110(W)x38(H)xmm
2 year warranty
Incorporates short circuit, over load, over voltage and over temperature
protection with CSA/NRTLC/CE approvals. Powered from 176-264VAC
it is fitted with terminal connections. The specifications are
Tolerance +/-2% 13.5VDC, +/-1% 27VDC
and 54VDC
Ripple and Noise 100mV on 13.5VDC,
150mV on 27VDC and 400mV on 54VDC
Efficiency >81%
Working Temperature 0-40degC @
100degC, -10C @80%, 60C @ 60% load
Measurements 150(L)x140(W)x75(H)
xmm
2 year warranty
Price Each
PSM-057 +5V/11A, +12V/4A, -5V/0.5A, -12V/1A
PSM-058 +5V/10A, +15V/3.5A, -5V/1A, -15V/1A
PSM-059 +5V/8A, +12V/2A, +24V/2A, -12V/1A
1
$104.00
$104.00
$104.00
3+
less 10%
less 10%
less 10%
55W Switchmode supply with Battery Charger
Features short circuit, over load and over voltage protection. Battery
low and Battery polarity protection. Approvals include UL/CUL/TUV/
CB/CE. Free air cooling convection. Powered from 88-264VAC they
are fitted with screw terminals. The specifications are
Tolerance +/-1%
Ripple and Noise 100mV
Efficiency >71%
Working Temperature 0-50degC
Measurements 159(L)x97(W)x38(H)xmm
2 year warranty
Price Each
1
PSM-104 13.8VDC/4A supply, 13.4V/0.23A charger $84.00
PSM-105 27.6VDC/2A supply, 26.5V/0.16A charger $84.00
5+
less 10%
less 10%
20W Slimline DIN Rail Switchmode Supplies
These are available in 5, 12 and 24VDC. They are temperature, over
voltage protected and current limited. Built in EMI filter and power on
LED. Feature DC OK Relay contact.
- Overload protection 105%~160% constant current limiting, autorecovery
- Over voltage protection 115%~135% rated output voltage, shut off
- Working temperature -20~50°C@100%, 70°C@50% load Input voltage from 85-264VAC.
- DC adjustment range ±10%
- Ripple and Noise 120mV(12VDC), 150mV
(24VDC)
- Efficiency 80%(12VDC) 84%(24VDC)
- Output Current 1.67A(12VDC) 1.0A(24VDC)
- Case dimension (L×W×H) 22.5×90×100 mm
3 year warranty
Price Each
PSM-150 20W Power Supply 5VDC
PSM-151 20W Power Supply 12VDC
PSM-152 20W Power Supply 24VDC
1
$64.00
$64.00
$58.00
3+
less 10%
less 10%
less 10%
Price Each
PSM-101 Battery Charger +13.5VDC/16A
PSM-102 Battery Charger +27VDC/8A
5+
less 10%
less 10%
155W Switchmode supply with Battery Charger
Features short circuit, over load and over voltage protection. Battery low
and Battery polarity protection. Approvals include UL/CUL/TUV/CB/CE.
Free air cooling convection. Powered from 88-264VAC. The specifications are
Tolerance +/-2% 13.8V, +/-1% 27.6V and 54V
Ripple and Noise 150mV on 13.8V and 27.6V, 240mV on 54V
Efficiency >80%
Working Temperature
Without Fan -10~50degC 70% load
With Fan -10~50degC 100% load
Measurements 199(L)x110(W)x50(H)
xmm
2 year warranty
Price Each
1
5+
PSM-106 13.8V/11A,5V/3A & 13.3V/0.5A charger $162.00 less 10%
PSM-107 27.6V/5.5A,5V/3A & 27.1V/0.5A charger $162.00 less 10%
PSM-108 54V/2.7A,5V/3A & 53.5V/0.5A charger
$162.00 less 10%
40W Slimline DIN Rail Switchmode Supplies
These are available in 5, 12, 24 and 48VDC. They are temperature, over
voltage protected and current limited. Built in EMI filter and power on
LED. Features DC OK Relay Contact
- Input voltage from 85-264VAC.
- DC adjustment range ±10%
- Overload protection 105%~160% constant current limiting, autorecovery
- Over voltage protection 115%~135% rated
output voltage, shut off
- Working temperature -20~50°C@100%,
70°C@50% load
- Ripple and Noise 120mV(12VDC), 150mV
(24VDC)
- Efficiency 86%(12VDC) 88%(24VDC)
- Output Current 3.3A(12VDC) 1.7A(24VDC)
- Case dimension (L×W×H) 40×90×100 mm
- 3 Year warranty
30W Industrial DIN Rail Switchmode Supplies
Price Each
PSM-153 40W Power Supply 12VDC
These switchmode power supplies are available in 5VDC,12VDC and
PSM-154 40W Power Supply 24VDC
24VDC. They are temperature, over voltage protected and current limPSM-155 40W Power Supply 48VDC
ited. Built in EMI filter and power on LED.
Input voltage from 85-264VAC.
Tolerance +/-1%(12VDC), +/-1%(24VDC)
Ripple and Noise 120mV(12VDC), 150mV
(24VDC)
Efficiency >74%
Price Each
Measurements 78x93x56mm
PSM-020 30W Power Supply 5VDC
Output Current 2.0A(12VDC) 1.5A(24VDC)
PSM-021 30W Power Supply 12VDC
3 year warranty
PSM-022 30W Power Supply 24VDC
Page 98 Ocean Controls Catalog 2009
1
$174.00
$174.00
1
$76.00
$70.00
$76.00
1
$58.00
$58.00
$58.00
3+
less 10%
less 10%
less 10%
3+
less 10%
less 10%
less 10%
OCEAN CONTROLS - POWER SUPPLIES
45W Industrial DIN Rail Switchmode Supplies
60W Slimline DIN Rail Switchmode Supplies
These switchmode power supplies are available in 5VDC,12VDC and
24VDC. They are temperature, over voltage protected and current limited. Built in EMI filter and power on LED.
Input voltage from 85-264VAC.
Tolerance +/-1%(12VDC), +/-1%(24VDC)
Ripple and Noise 100mV(12VDC), 150mV
(24VDC)
Efficiency >75%
Measurements 93x78x67mm
Output Current 3.5A(12VDC) 2.0A(24VDC)
3 year warranty
These are available in 5, 12, 24 and 48VDC.
They are temperature, over voltage protected
and current limited. Built in EMI filter and power
on LED. Features DC OK Relay Contact
- Input voltage from 85-264VAC.
- DC adjustment range ±10% rated output
voltage
- Overload protection 105%~160% constant
current limiting, auto-recovery
- Over voltage protection 115%~135% rated
output voltage, shut off
- Working temperature -20~50°C@100%, 70°C@50% load
- Ripple and Noise 120mV(12VDC), 150mV(24VDC)
- Efficiency 86%(12VDC) 88%(24VDC)
- Output Current 5A(12VDC) 2.5A(24VDC)
- Case dimension (L×W×H) 40×90×100 mm , 3 year warranty
Price Each
PSM-156 60W Power Supply 12VDC
PSM-157 60W Power Supply 24VDC
PSM-158 60W Power Supply 48VDC
1
$80.00
$74.00
$80.00
Price Each
PSM-029 45W Power Supply 5VDC
PSM-030 45W Power Supply 12VDC
PSM-031 45W Power Supply 24VDC
These supplies are available in 12VDC and 24VDC. They are temperature, over voltage protected and current limited. Built in EMI filter
and power on LED. Input voltage from 85-264VAC.
Tolerance +/-2%(12VDC), +/-1%
(24VDC)
Ripple and Noise 100mV(12VDC),
150mV(24VDC)
Efficiency >75%
Measurements 100x56x125mm
Output Current 12.5A(12VDC) 6.5A
(24VDC)
3 year warranty
1
$100.00
$100.00
3+
less 10%
less 10%
240W Industrial DIN Rail Switchmode Supplies
This switchmode power supplies is available 24VDC and 48VDC. It is
temperature, over voltage protected and
current limited. Built in EMI filter and
power on LED. Input voltage from 85264VAC.
Tolerance +/-1%
Ripple and Noise 84mV
Efficiency >84%
Measurements 126x100x126mm
Output Current 10A(24VDC)
3 year warranty
Price Each
PSM-036 240W Power Supply
PSM-040 240W Power Supply
24VDC
48VDC
1
$185.00
$185.00
Price Each
PSM-072 240W Power Supply
PSM-073 240W Power Supply
Page 99 Ocean Controls Catalog 2009
24VDC
48VDC
3+
less 10%
less 10%
less 10%
120W Industrial DIN Rail Switchmode Supplies
3+
less 10%
less 10%
less 10%
75W Industrial DIN Rail Switchmode Supplies
Price Each
PSM-032 75W Power Supply 12VDC
PSM-033 75W Power Supply 24VDC
1
$66.00
$66.00
$66.00
3+
less 10%
less 10%
1
$210.00
$210.00
These switchmode power supplies are available in 12VDC and
24VDC. They are temperature, over voltage protected and current
limited. Built in EMI filter and power on LED. Input voltage from 85264VAC.
Tolerance +/-2%(12VDC), +/-1%
(24VDC)
Ripple and Noise 100mV(12VDC),
150mV(24VDC)
Efficiency >75%
Measurements 100x56x125mm
Output Current 12.5A(12VDC) 6.5A
(24VDC)
3 year warranty
Price Each
PSM-034 120W Power Supply 12VDC
PSM-035 120W Power Supply 24VDC
PSM-039 120W Power Supply 48VDC
1
$115.00
$115.00
$115.00
3+
less 10%
less 10%
less 10%
480W Industrial DIN Rail Switchmode Supplies
This switchmode power supplies is only available 24VDC. It is temperature, over voltage protected and current
limited.
Built in EMI filter and power on LED. Input
voltage from 85-264VAC.
Tolerance +/-1%
Ripple and Noise 120mV
Efficiency >89%
Measurements 227x100x126mm
Output Current 20A(24VDC)
3 year warranty
Price Each
PSM-037 480W Power Supply
PSM-038 480W Power Supply
24VDC
48VDC
1__________3+__
$275.00
less 10%
$275.00
less 10%
240W 3 Phase Industrial DIN Rail Switchmode Supplies
This switchmode power supplies is only available 24VDC and 48VDC. It
is temperature, over voltage protected and
current limited. Built in EMI filter and
power on LED. Input voltage from 340550VAC.
DC Adjustment range 24V: 24-28V, 48V:
48-55V
Tolerance +/-1%
Ripple and Noise 80mV
Efficiency 89%
Working Temperature -20 to 70degC
(Refer to Derating Curve)
3+
Measurements 126x100x126mm
less 10%
Output Current 10A(24VDC) 5A(48VDC)
less 10%
3 year warranty
OCEAN CONTROLS - POWER SUPPLIES & DC-DC CONVERTERS
480W 3 Phase Industrial DIN Rail Switchmode Supplies
120W 415VAC DIN Rail Switchmode Supplies
This switchmode power supplies is only available 24VDC and 48VDC. It
is temperature, over voltage protected and current limited. Built in EMI
filter and power on LED. Input voltage from 340
-550VAC.
Tolerance +/-1%
Ripple and Noise 80mV
Efficiency >89%
Measurements 227x100x126mm
Output Current 20A(24VDC) 10A(48VDC)
3 year warranty
Price Each
PSM-074 480W Power Supply
PSM-075 480W Power Supply
24VDC
48VDC
1__________3+__
$299.00
less 10%
$299.00
less 10%
960W 3 Phase Industrial DIN Rail Switchmode Supplies
This switchmode power supplies is only available 24VDC and 48VDC. It
is temperature, over voltage protected and current limited. Built in EMI
filter and power on LED. Input voltage from 340-550VAC.
Tolerance +/-1%
Ripple and Noise 80mV
Efficiency >91%
Measurements 276x100x126mm
Output Current 40A(24VDC) 20A(48VDC)
3 year warranty
Price Each
PSM-076 960W Power Supply
24VDC
1__________3+__
$540.00
less 10%
25W Single Output DC-DC Converter
These 25W industrial grade DC-DC converters feature:
500VDC I/O isolation
Insulation resistance 100MOhm@500VDC
Built in EMI Filter
Over voltage protected, short circuit and overload protected
UL/TUV/CE approvals.
Screw terminals.
Line Regulation +/-0.5%
Load Regulation +/-0.5%
Ripple and Noise <150mV
Efficiency >70%
Measurements 99(L)x97(W)x35(H)xmm
Output Current 2.1A(12VDC) 1.1A(24VDC)
1 year warranty
Price Each
PDC-001 9.2-18V(Input) 12V, 2.1A(Output)
PDC-002 9.2-18V(Input) 24V, 1.1A(Output)
PDC-003 19-36V(Input) 12V, 2.1A(Output)
PDC-004 19-36V(Input) 24V, 1.1A(Output)
1
3+
$60.00 less 10%
$60.00 less 10%
$60.00 less 10%
$60.00 less 10%
TOL-060 DC to DC converter module
These switchmode power supplies are available in 24VDC and 48VDC.
They are temperature, over voltage protected and current limited. Built in
EMI filter and power on LED. Input voltage from 340-550VAC.
DC Adjustment range 24V: 24-28V, 48V:
48-55V
Tolerance +/-1%
Ripple and Noise 80mV
Efficiency 85%
Working Temperature -20 to 60degC
Measurements 100x66x125mm
Output Current 5A(24VDC) 2.5A(48VDC)
3 year warranty
Price Each
PSM-070 120W Power Supply 24VDC
PSM-071 120W Power Supply 48VDC
3+
less 10%
less 10%
50W Single Output DC-DC Converter
These 50W industrial grade DC-DC converters feature:
500VDC I/O isolation
Insulation resistance 100MOhm@500VDC
Built in EMI Filter
Over voltage protected, short circuit and overload protected
UL/TUV/CE approvals.
Screw terminals.
Line Regulation +/-0.5%
Load Regulation +/-0.5%
Ripple and Noise <150mV
Efficiency >70%
Measurements 159(L)x97(W)x38(H)xmm
Output Current 4.2A(12VDC) 2.1A(24VDC)
1 year warranty
Price Each
PDC-005 9.2-18V(Input) 12V, 4.2A(Output)
PDC-006 9.2-18V(Input) 24V, 2.1A(Output)
PDC-007 19-36V(Input) 12V, 4.2A(Output)
PDC-008 19-36V(Input) 24V, 2.1A(Output)
1
3+
$74.00 less 10%
$74.00 less 10%
$74.00 less 10%
$74.00 less 10%
100W Single Output DC-DC Converter
These 100W industrial grade DC-DC converters feature:
500VDC I/O isolation
Insulation resistance 100MOhm@500VDC
Built in EMI Filter
Over voltage protected, short circuit and overload protected
UL/TUV/CE approvals.
Screw terminals.
Line Regulation +/-0.5%
Load Regulation +/-0.5%
Ripple and Noise <150mV
Efficiency >74%
Measurements 199(L)x98(W)x38(H)mm
Output Current 8.5A(12VDC) 4.2A(24VDC)
1 year warranty
Description: This is a SMD non-isolated dc-dc converter that can deliver
up to 5A of output current with full load efficiency of 89% at 3.3V output. These modules provide precisely regulated output voltage programmable via external resistor from 0.75Vdc to 5.5Vdc over a wide
range of input voltage (VIN = 10 - 14V). Their open-frame construction
and small footprint enable designers to develop cost- and space-efficient
Price Each
solutions. Standard features include remote On/Off, programmable
PDC-011 19-36V(Input) 12V, 8.5A(Output)
output voltage and overcurrent protection.
PDC-012 19-36V(Input) 24V, 4.2A(Output)
Features:
* 10-14V Input voltage
* 3.3V Regulated output
* 5A max output current
* High reliability: 5.6M hours at 25C fully loaded
* Low output ripple and noise
* Line Regulation: 0.3%
* Load Regulation: 0.4%
Price Each
1
5+
* Temperature Regulation: 0.4%
PDC-060 DC to DC converter module
$18.77 less 10%
* -40C to 85C operating temperatures
Page 100 Ocean Controls Catalog 2009
1
$164.00
$164.00
1
3+
$96.00 less 10%
$96.00 less 10%
OCEAN CONTROLS - DC-DC CONVERTERS
1W DC-DC Unregulated Single Output
3W DC-DC Regulated Single and Dual Output
Features:
1000VDC I /O isolation •
Internal SMD technology •
Built - in EMI filter •
Protection: Short circuit •
Cooling by free air convection •
Non-conductive plastic case •
Dual in line package •
SIP package is available •
100% full load burn-in test •
Low cost , high reliability •
2 years warranty
Price Each
SDC-001 DC-DC 1W 5±10%VDC(Input) 5VDC(Output)
SDC-003 DC-DC 1W 5±10%VDC(Input) 12VDC(Output)
SDC-005 DC-DC 1W 12±10%VDC(Input) 5VDC(Output)
SDC-007 DC-DC 1W 12±10%VDC(Input) 12VDC(Output)
SDC-009 DC-DC 1W 24±10%VDC(Input) 5VDC(Output)
SDC-011 DC-DC 1W 24±10%VDC(Input) 12VDC(Output)
Features:
2:1 wide input range
4:1 wide input range (option)
1000VDC I /O isolation
3000VDC I /O isolation (option)
Built - in EMI filter
Protection: Short circuit / Overload
Cooling by free air convection
Five-sided shield metal case
100% full load burn-in test
Low cost , high reliability
2 years warranty
1
$12.60
$12.60
$12.60
$12.60
$12.60
$12.60
3+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
5-6W DC-DC Regulated Single and Dual Output
Features:
2:1 wide input range
4:1 wide input range (option)
1000VDC I /O isolation
3000VDC I /O isolation (option)
Built - in EMI filter
Protection: Short circuit / Overload
Cooling by free air convection
Five-sided shield metal case
100% full load burn-in test
Low cost , high reliability
2 years warranty
Price Each
SDC-501 DC-DC 5-6W 9-18VDC(Input) 5VDC(Output)
SDC-503 DC-DC 5-6W 9-18VDC(Input) 12VDC(Output)
SDC-505 DC-DC 5-6W 18-36VDC(Input) 5VDC(Output)
SDC-507 DC-DC 5-6W 18-36VDC(Input) 12VDC(Output)
SDC-509 DC-DC 5-6W 36-72VDC(Input) 5VDC(Output)
SDC-511 DC-DC 5-6W 36-72VDC(Input) 12VDC(Output)
1
$27.54
$27.54
$27.54
$27.54
$27.54
$27.54
3+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
DDC-301 DC-DC 3W 9-18VDC(Input) ±5VDC(Output)
DDC-302 DC-DC 3W 9-18VDC(Input) ±12VDC(Output)
DDC-304 DC-DC 3W 18-36VDC(Input) ±5VDC(Output)
DDC-305 DC-DC 3W 18-36VDC(Input) ±12VDC(Output)
DDC-307 DC-DC 3W 36-72VDC(Input) ±5VDC(Output)
DDC-308 DC-DC 3W 36-72VDC(Input) ±12VDC(Output)
$28.98
$28.98
$28.98
$28.98
$28.98
$28.98
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
12W DC-DC Regulated Single and Dual Output
1
$30.42
$30.42
$30.42
$30.42
$30.42
$30.42
3+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
DDC-501 DC-DC 5-6W 9-18VDC(Input) ±5VDC(Output) $33.84
DDC-502 DC-DC 5-6W 9-18VDC(Input) ±12VDC(Output) $33.84
DDC-504 DC-DC 5-6W 18-36VDC(Input) ±5VDC(Output) $33.84
DDC-505 DC-DC 5-6W 18-36VDC(Input) ±12VDC(Output)$33.84
DDC-507 DC-DC 5-6W 36-72VDC(Input) ±5VDC(Output) $33.84
DDC-508 DC-DC 5-6W 36-72VDC(Input) ±12VDC(Output)$33.84
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
Page 101 Ocean Controls Catalog 2009
Price Each
SDC-301 DC-DC 3W 9-18VDC(Input) 5VDC(Output)
SDC-302 DC-DC 3W 9-18VDC(Input) 12VDC(Output)
SDC-304 DC-DC 3W 18-36VDC(Input) 5VDC(Output)
SDC-305 DC-DC 3W 18-36VDC(Input) 12VDC(Output)
SDC-307 DC-DC 3W 36-72VDC(Input) 5VDC(Output)
SDC-308 DC-DC 3W 36-72VDC(Input) 12VDC(Output)
Features:
2:1 wide input range
1500VDC I /O isolation
Built - in remote ON/OFF control
Protection: Short circuit / Overload
Cooling by free air convection
Five-sided shield metal case
100% full load burn-in test
Low cost , high reliability
2 years warranty
Price Each
1
SDC-701 DC-DC 12W 9-18VDC(Input) 5VDC(Output)
$52.74
SDC-702 DC-DC 12W 9-18VDC(Input) 12VDC(Output) $52.74
SDC-704 DC-DC 12W 18-36VDC(Input) 5VDC(Output) $52.74
SDC-705 DC-DC 12W 18-36VDC(Input) 12VDC(Output) $52.74
SDC-707 DC-DC 12W 36-72VDC(Input) 5VDC(Output) $52.74
SDC-708 DC-DC 12W 36-72VDC(Input) 12VDC(Output) $52.74
3+
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
DDC-701 DC-DC 12W 9-18VDC(Input) ±5VDC(Output) $55.62
DDC-702 DC-DC 12W 9-18VDC(Input) ±12VDC(Output) $55.62
DDC-704 DC-DC 12W 18-36VDC(Input) ±5VDC(Output) $55.62
DDC-705 DC-DC 12W 18-36VDC(Input) ±12VDC(Output) $55.62
DDC-707 DC-DC 12W 36-72VDC(Input) ±5VDC(Output) $55.62
DDC-708 DC-DC 12W 36-72VDC(Input) ±12VDC(Output) $55.62
less 10%
less 10%
less 10%
less 10%
less 10%
less 10%
OCEAN CONTROLS - POWER SUPPLY KITS & BATTERY HOLDERS
Positive Adjustable Power Supply
Negative Adjustable Power Supply
A compact, easy to build and use,
positive variable power supply module. It is ideal for powering any application requiring a DC supply at current levels up to 1.5 amperes. Can
be combined with PSU-011 to create
a dual-rail supply.
A compact, easy to build and use,
positive variable power supply module. It is ideal for powering any application requiring a DC supply at current levels up to 1.5 amperes. Can
be combined with PSU-009 to create
a dual-rail supply.
Features:
Ouput reverse polarity and back-voltage protection
LED power on indication
On board heatsink for regulator IC (LM317T)
Variable output voltage from 1.2V to 35V
AC or DC input voltage
Screw terminals for input, output and LED indicator
Compact dimensions - 84mm x 37mm (3.3" x 1.4")
Features:
Ouput reverse polarity and back-voltage protection
LED power on indication
On board heatsink for regulator IC (LM337T)
Variable output voltage from -1.2V to -35V
AC or DC input voltage
Screw terminals for input, output and LED indicator
Price Each
PSU-009 Positive Adjustable PS as kit
PSU-010 Positive Adjustable PS assembled
1
$22.50
$35.00
5+
less 10%
less 10%
Price Each
PSU-011 Negative Adjustable PS as kit
PSU-012 Negative Adjustable PS assembled
1
$22.50
$35.00
5+
less 10%
less 10%
VPack5.0V 2-AA Battery Holder w/ 5V Regulator
VPack5.0V 2-AAA Battery Holder w/ 5V Regulator
This battery holder from Bodhilabs takes two AA cells and has an efficient 5V step-up regulator on the back, giving you a simple power
source for your 5V circuits. If you’re looking for an easy way to get a
regulated 5 V for your electronics project, this battery holder from Bodhilabs is just what you need. It comes with a step-up DC-to-DC converter on the back that can provide up to 200 mA (typical; 500 mA max),
and there is a jumper that can be removed to disconnect the batteries
from the regulator and give you direct
access to the battery voltage.
This battery holder from Bodhilabs takes two AAA cells and has an efficient 5V step-up regulator on the back, giving you a simple power
source for your 5V circuits.If you’re looking for an easy way to get a
regulated 5 V for your electronics project, this battery holder from Bodhilabs is just what you need. It comes with a step-up DC-to-DC converter on the back that can provide up to 200 mA (typical; 500 mA max),
and there is a jumper that can be removed to disconnect the batteries
from the regulator and give you direct
access to the battery voltage.
Dimensions
Weight: 0.35 oz
General specifications
Maximum supply current: 200 mA
Default output voltage: 5 V
Lead length: 4.5 in
Cells: 2
Cell type: AA
Dimensions
Weight: 0.32 oz
General specifications
Maximum supply current: 200 mA
Default output voltage: 5 V
Lead length: 4.5 in
Cells: 2
Cell type: AAA
Price Each
1
5+
POL-781 VPack5.0V 2-AA Battery Holder w/ 5V Regulator $18.50 less 10%
Price Each
1
5+
POL-783 VPack5.0V 2-AAA Battery Holder w/5V Regulator $18.50 less10%
BVPack3.3V 1-AA Battery Holder w/ 3.3V Regulator
VPack3.3V 1-AAA Battery Holder w/ 3.3V Regulator
This battery holder from Bodhilabs takes one AA cell and has an efficient 3.3V step-up regulator on the back, giving you a simple power
source for your 3V3 circuits.If you’re looking for an easy way to get a
regulated 3.3 V for your electronics project, this battery holder from Bodhilabs is just what you need. It comes with a step-up DC-to-DC converter on the back that can provide up to 100 mA, and there is a jumper
that can be removed to disconnect the batteries from the regulator and
give you direct access to the battery voltage.
This battery holder from Bodhilabs takes one AAA cell and has an efficient 3.3V step-up regulator on the back, giving you a simple power
source for your 3V3 circuits.If you’re looking for an easy way to get a
regulated 3.3 V for your electronics project, this battery holder from Bodhilabs is just what you need. It comes with a step-up DC-to-DC converter on the back that can provide up to 100 mA, and there is a jumper
that can be removed to disconnect the batteries from the regulator and
give you direct access to the battery voltage.
Dimensions
Weight: 0.22 oz
General specifications
Maximum supply current: 100 mA
Default output voltage: 3.3 V
Lead length: 4.5 in
Cells: 1
Cell type: AA
Price Each
1
5+
POL-796 VPack3.3V 1-AA Battery Holder w/3.3V Regulator $17.50 less10%
Page 102 Ocean Controls Catalog 2009
Dimensions
Weight: 0.18 oz
General specifications
Maximum supply current: 100 mA
Default output voltage: 3.3 V
Lead length: 4.5 in
Cells: 1
Cell type: AAA
Price Each
1
5+
POL-797 VPack3.3V 1-AAA Battery Holder w/3.3V Regulator $17.50 less 10%
OCEAN CONTROLS - POWER SUPPLY KITS & BATTERY HOLDERS
Polymer Lithium Ion Batteries - 860mAh
Plug Packs
We stock a selection of non regulated Plugs
Packs suitable for use with our data acquisition equipment, relay controllers and microcontroller programmers.
Each of the plug packs have a selection of
plug connectors making it easy to connect to
your equipment
Price Each
PLP-001 6V, 7.5V, 9V, 12V 1Amp Plug Pack
PLP-003 12VDC 450mA Plug Pack
PLP-006 12VAC 500mA Plug Pack
PLP-005 18VDC 500mA Plug Pack
1
$20.00
$14.55
$15.18
$22.00
Description: These are very
slim, extremely light weight batteries
based on the new Polymer Lithium Ion
chemistry. This is the highest energy density
currently in production. Each cells outputs a
nominal 3.7V at 860mAh! Comes terminated
with a standard 2-pin JST connector - 2mm
spacing between pins. These batteries require special charging : Do not attempt to
charge these with anything but a specialized
LiPo charger.
Battery includes built-in protection against over voltage, over current,
and minimum voltage.
Features:
LiPoly Charger - Single Cell 3.7-7V Input
Description: This is a Polymer
Lithium Ion battery charger based on the
MAX1555 IC. This charger uses either USB
bus power (MAX1555 internally limits this to
100mA) or 2.1mm center positive wall-wart
power (MAX1555 internally limits this to
300mA). Current is automatically reduced to a
trickle when charging is complete. Cheap,
easy to use, and flexible, this board serves as
a great demo board for the MAX1555. This
charger is a 'must have' for quick and clean charging of Lithium Polymer
chemistry batteries.
Check out this iPhone Charger!
Features:
* Intelligent IC monitored charging - Constant current/Constant Voltage
* Do not use this charger to charge NiMH, NiCd, or any other battery
type
* Comes fully assembled and tested
* Single Cell Charger
* Requires 3.7V to 7V(max!) Input
* MAX1555 will automatically choose the wall-wart charging if both
USB and barrel jacks are connected to power
* Separate header for external power in
* Separate headers for battery and load system so batteries don't
have to be removed for charging
Price Each
BAT-003 LiPoly Charger - Single Cell 3.7-7V Input
1
5+
$22.60 less 10%
* 2C continuous discharge
* Excellent long-term self-discharge rates (<8% per month)
* Robust power source under extreme conditions (-25 to 60C)
Dimensions: 0.23x1.16x2.0" (5.84x29.5x51mm)
Price Each
BAT-002 Polymer Lithium Ion Batteries - 860mAh
1
$11.95
5+
less 10%
LiPoly Fast Charger - 5-12V Input
Description: A SparkFun
original Lithium Polymer charger.
This little black box charges single cell lithium polymer batteries with a max rate of 1A.
This works well with our 5V/1A regulated
supply. The charge output is via a 2-pin
screw terminal. Top pin is ground, bottom
pin is charge pin. Based on the popular
Microchip part MCP73843-410.
Price Each
BAT-004 Lipoly Fast Charger - 5-12V Input
1
$27.65
5+
less 10%
Polymer Lithium Ion Batteries - 100mAh
Description: This is a very small, extremely light weight batty
based on the new Polymer Lithium Ion chemistry. This is the highest
energy density currently in production. Each cells outputs a nominal
3.7V at 100mAh! Comes terminated with a standard 2-pin JST connector - 2mm spacing between pins. These batteries require special charging. Do not attempt to charge these with anything but a specialized Lithium Polymer
charger.
Battery includes built-in protection against over
voltage, over current, and minimum voltage.
Features:
* 2C continuous discharge - very high for
low price
* Excellent long-term self-discharge rates
(<8% per month)
* Robust power source under extreme conditions (-25 to 60C)
Dimensions: 0.19x0.52x1.19" (4.7x13x28mm)
Weight: about 3g - Our scale doesn't go this low
Price Each
BAT-005 Polymer Lithium Ion Batteries - 100mAh$
Page 103 Ocean Controls Catalog 2009
1
8.34
5+
less 10%
OCEAN CONTROLS - TEST EQUIPMENT
Digital Function Generator
Digital Tachometer
This digital function generator has variable
sweep rate and width, as well as functioning as
a standard waveform generator with sinusoidal, triangle and square wave outputs. DC
offset adjustment allows the waveform to be
shifted above or below 0V, and symmetry adjustment can be used to
generate asymmetrical waveforms, with positive going cycles of narrower width than the negative going pulses. Output amplitude is adjustable from 0 to 10V p-p via front panel control, with a switchable -20dB
attenuator. Output frequency is adjustable between 0.02Hz to 2MHz
Price Each
MET-100 Function Generator & Frequency Counter
1
$453.64
Digital Tachometer Laser Photo/Contact
Model DT-1236L
Features
* From Lutron World's patent, Multi-functions, one
instrument combine Photo Tach.( RPM ) & Contact
Tach. ( RPM, m/min., ft/min. ).
* High visible LCD display gives RPM reading exactly with no guessing or errors & saves battery
* Laser light source, long detecting distance.
* Wide measuring range from 0.5 to 100,000 RPM
* This tachometer uses one chip LSI circuit & crystal
time base, offering a high accurate measurement &
fast sampling time.
* 0.1 RPM resolution measured value < 1000 RPM.
* The use of durable, long lasting components, including a strong, light
weight ABS plastic housing, assures almost maintenance free performance for many years. Carry case included.
* High precison with 0.05% accuracy.
* The last value, max., value, min. value will be stored into the memory
automatically & can be . obtained by pressing Memory Call Button.
* The housing cabinet has been carefully shaped
to fit comfortable in either hand. 9V Alkaline Battery
Price Each
MET-005 DT-1236L Digital Tachometer
1
$308.00
Digital Tachometer Laser Photo/Contact
Features include
* From Lutron World's patent, Multi-functions, one
instrument combine Photo Tachometer (RPM ) and
Contact Tachometer ( RPM, m/min., ft/min. ).
* Wide measuring range : 0.5 to 100,000 RPM.
* < 1,000 RPM, 0.1 RPM resolution .
* High precision with 0.05% accuracy.
* Memorize the last value, max., value, min. value
* High visible LCD display.
* Exclusive one chip LSI circuit & crystal time base
* The use of durable, long lasting components, including a strong, light weight ABS plastic housing,
assures almost maintenance free performance for
many years. Battery and Hard Carry Case included
Price Each
MET-010 DT-2236 Digital Tachometer
Price Each
MET-001 Digital Tachometer
1
$72.68
Dwell Tachometer Digital Multimeter
Features include a 3.5 digit LCD display with automatic zero adjustment,
low battery warning and auto power off after 15 minutes. Includes dwell
angle and RPM (x1, x10) for 4, 5, 6 and 8 cylinder engines.
Specifications
- RPM x 1, x10
- Dwell angle
- Resistance
- DC volts
- 15 amp DC
- Continuity buzzer
- Probe clips and Holster included
Comprehensive user guide describes how to:
- Use dwell angle function
- Dual point distributors
- Set idle speed and mixture setting
- Adjust fast idle speed
- Air fuel ratio test
- Air filter test
- Cylinder power balance test
- Positive crankcase ventilator (PCV) test
- Distributor centrifugal advance test
- Heavy and light load battery test
- Charging system test
- Starter circuit
- Alternator output voltage
- Generator output voltage
1
$54.50
Tempgun with Laser Sight
1
$276.00
Description: By simply plugging this compact meter into a standard power point (GPO), you are
able to calculate the running costs of any connected appliance. It tracks power usage and can
display instantaneous voltage or current draw.
Internal batteries maintain data during mains failure. To calculate real running costs, key in the
local price per unit of electricity as charged by your
provider.
Page 104 Ocean Controls Catalog 2009
Specifications:
Display: 5 Digits, 16mm 0.7" LCD
Test range: 2.5 to 99,999 RPM
Resolution: 0.1RPM (2.5 - 999.9 RPM), 1RPM (over
1000PRM)
Accuracy: 0.05%
Price Each
MET-003 Dwell Tachometer and DVM
Power Meter
Price Each
MET-042 Power Meter
This easy-to-use hand held digital tachometer measures up to 99,999 RPM and features a large LCD
display, laser pointer, low battery indicator, and memory recall for the last displayed value, minimum value,
and maximum value. It can also be switched to measure either actual RPM or total revolutions. Supplied
with carry case and 600mm reflective tape marks,
which can be cut to size.
1
$30.90
This is TempGun PE2, the next generation non-contact infrared thermometer. Higher accuracy, laser sighting, and a tighter emission profile
make this new unit a must have for tighter tolerance measurements.
Just point it at any object and get the surface temperature. Remember
the days when you couldn't buy a laser pointer for under AUD$150?
Now you can get one for AUD$65 with a surface temperature to boot!
* Range: (-27°F to 428°F) switchable to Celsius (-33°C to 220°C)
* Resolution: 0.1°
* Accuracy: ±2 Degrees
* Response Time: 1 second
* Field of View (D:S Ratio): 8:1
* Modes: Max/Min/Lock
* Emissivity: 0.05~1 adjustable
* 40 hours continuous use battery life
* Two CR2032 batteries
* Weight 80 grams
* Warranty 1 Year
Dimensions: 22x50x110mm
Price Each
MET-022 Tempgun with Laser Sight
1
$74.95
OCEAN CONTROLS - TEST EQUIPMENT
Infra-red Thermometer
Relative Humidity and Temperature
Compact, lightweight, handheld infra-red thermometer enables accurate laser guided non-contact temperature measurement of any given object (even in
the dark). It features easy one hand operation and
can measure temperatures from -30°C to 550°C. It
includes functions for minimum and maximum readings, selectable auto power off, data hold and adjustable warning alarm when temperature rises or falls
below user set levels. The backlit display allows
easy reading in dark areas. Can display in either °C
or °F.
Specifications:
Detection element:Thermopile, Optical lens:Fresnel
Sighting:< 1mW laser marker, Range:-30°C to 550°C
Resolution:0.5°C Accuracy: ± 2°C (-30°C to 100°C),
± 2% reading (101°C to 550°C)
Temp coefficient:±0.2% of reading or 0.2°C (which ever is greater)
Response time: 0.25 seconds Spectral response: 6 to 14µm nominal
Adjust emissivity (e): 0.1 to 1.0
Dimensions:˜ 105W x 42D x 148H mm
Price Each
MET-020 Infra-Red Thermometer
1
$104.55
2 instruments in one. Ideal for network installers or technicians and allows the user to easily check cable integrity or measure AC & DC voltage, current, resistance, and continuity etc. without needing to carry two
separate devices. The unit will check for cable continuity, open-circuits,
short-circuits, and cross-connects etc. A remote
terminator is included and enables the user to
check network cables at a wall jack or patch
panel. Supplied with loop back cable, LAN
terminator, and multimeter leads.
LAN tester specifications:
* LAN tester checks faults & miss wired conductors
* Manual or automatic testing
DMM Specifications:
* 600 volt max input
* 200mA AC/DC
* 20M ohm resistance
* 3.5 digit
* Diode test, Data Hold andMax hold
1
$90.86
K Type Thermocouple Meter
Accepts standard K-type thermocouples.
Specifications:
• Display: 3.5 digit LCD
• Range: -50 - 750°C
• Accuracy: ±1°C
• Dimensions: 118(L) x 70(W) x 29(H)mm
Page 105 Ocean Controls Catalog 2009
Price Each
MET-030 Relative Humidity and Temperature Meter
1
$125.00
MET-050 Multimeter Auto Ranging USB Datalogger DMM
An autoranging multimeter featuring an optically isolated USB interface
and Windows® software. The optical adaptor ensures the DMM is electrically isolated from the PC, so no damage can occur to the computer
should there be a fault in the circuit under test. It also measures temperature, frequency, capacitance, AC/DC voltage & current up to 10A.
Includes PC software, high quality rubber insulated test leads, temperature probe and is housed in a shock-proof rubber coated case. Data
Acquisition: The USB interface and software allows you to log and store
measurements for later analysis. This is particularly useful for monitoring
the performance of battery chargers or dischargers, timed circuits or
other quantities that change with time. Suits Windows® XP & Vista.
Features
- Auto ranging with override
- Auto power off
- USB Interface
- Duty cycle % range
- Data hold & relative modes
- Bar graph readout
- Continuity buzzer & diode check
- Temperature sensor included
- Battery included
- Cat II 1000V
Specifications
DC voltage: 400mV, 4V, 40V, 400V
AC voltage: 400mV, 4V, 40V, 400V, 750V
DC current: 400µA, 4000µA, 40mA, 400mA, 4A, 10A
AC current: 400µA, 4000µA, 40mA, 400mA, 4A, 10A
Resistance: 400, 4k, 40k, 400k, 4M, 40M Ohm
Frequency: 100Hz, 1000Hz, 10kHz, 100kHz, 1MHz, 30MHz
Duty Cycle: 0.1% to 99.9%
Capacitance: 40nF, 400nF, 4µF, 40µF, 200µF
Continuity: <50 Ohm, Audible tester
Diode test: Test Current ˜1mA
Temperature: -20°C to 400°C, 400°C to 1000°C
Display: 3.75 digit LCD, 4000 count
Easy to Use Digital Thermometer
A handy pocket-size digital thermometer, suitable
for the lab, workshop or in the field. It features an
excellent measurement range from -50 to 750°C
and a hold function to lock the reading on the
display. Thermocouple included. Requires 9V
battery (included).
Price Each
MET-035 Digital Thermometer
Specifications:
Measuring range: 5-95% RH; -10 to 50°C
Accuracy:-+3% FS for RH and -+0.2% for temperature.
Sensors: capacitive polymer for RH and precision thermistor for °C.
Respose time: 60s typical.
HI and LO memory and HOLD function.
Auto shut-off in 20 seconds.
Measures in °C and °F.
Powered by 2 AAA batteries in Elegant enclosure with protective case.
Convenient pocket clip. Dimensions: 48x165x16 mm
Multimeter-USB Interface
Network Cable Tester and DVM
Price Each
MET-002 Network Cable Tester and DVM
This practical and convenient pocket
instrument accurately measures and
displays temperature and relative humidity simultaneously. It is an invaluable
companion for the HVAC technicians,
laboratory researchers, food storage
operators, librarians, or any professional
involved in computer rooms, printing
shops, paper, pulp and wood plants..
Dimensions: 95W x 48D x 192H mm
1
$45.40
Price Each
MET-050 Multimeter-USB Interface
1
$99.00
OCEAN CONTROLS - TEST EQUIPMENT
Digital Function Generator
Digital AC Clamp Meter & DMM
One of the most versatile pieces of test equipment you
can own. It provides a consistent waveform output,
useful for checking response of audio circuits etc. This
digital function generator has an in-built frequency
counter, as well as functioning as a standard waveform generator with
sinusoidal, triangle and square wave outputs. DC offset adjustment allows the waveform to be shifted above or below 0V. Output amplitude is
adjustable from 0 to 10V p-p via front panel control, with a switchable 20dB attenuator. Output frequency is adjustable between 0.03Hz to
3MHz via front panel rotary dial over seven ranges. It has an external
sync output for synchronising other test equipment to the signal generator, such as CROs and logic probes. This allows observation of phase
shifts relative to the signal generator output. It also features a 3 MHz 4
digit frequency counter with external BNC counter input. A self calibration mode ensures excellent accuracy at all times.
Features
• Sine, square & triangle waveforms
• External TTL sync output
• Tilt bail arm handle for bench stand angle adjustment
• High brightness seven segment LED displays
• BNC input/output connectors
• Push button range and waveform switching
• 3 MHz frequency counter
• External voltage controlled frequency
Specifications
Output
Frequency range: ...........................0.3Hz to 3MHz
Accuracy: .....................................±5% (at 3MHz position)
Amplitude: ....................................=10V p-p
Attenuator: ...................................-20dB ±1dB
Impedance: ..................................50 ohm ±5%
Sine Wave
Flatness: .....................................<0.3dB (0.3Hz - 300kHz), <0.5dB
(300kHz - 3MHz)
Distortion: ....................................=1% (0.3Hz - 200kHz) =35dB below
fundamental in all ranges.
Square Wave
Rise / fall time: .............................100ns or less
Symmetry variation: ......................±2% (0.3Hz - 200kHz)
Triangle Wave
Linearity:......................................98% or more to 100KHz
Frequency Counter
Range:.........................................0.3Hz - 3MHz
Accuracy: ...................................Time base accuracy ± 1 count
Time base: ..................................±20ppm
Resolution: ..................................10Hz up to 1Hz. 0.1Hz up to 100MHz
Input impedance: .........................1MO
CMOS output level:.......................4V p-p (±1V) / 14.5V p-p (±0.5V)
TTL output level: ..........................=3V p-p, fan out 20 TTL load
VCF input voltage: .......................0-10V ±1V (100 : 1)
VCF input impedance:..................10kO ±10%
General
Power requirements:....................240V AC
Dimensions:................................251W x 291D x 91H mm
Weight:.......................................˜ 2kg
Price Each
MET-105 Digital Function Generator
1
$312.73
Compact and durable, this digital clamp meter provides accurate AC current measurement up to 400A. Fits snugly into
one hand with thumbwheel function selector allowing simple
operation just about anywhere! Includes the functionality of a
typical standard DMM but with the addition of a non contact
AC voltage detector. Very useful when locating or working on
live equipment. The hold button will freeze the display on the
last measured reading. It also features autoranging AC/DC
volts and current, resistance, temperature, capacitance
ranges plus a diode and continuity test function. An essential
piece of test gear for high voltage technicians, instrument
fitters and other electrical trades people. Supplied with high
quality test leads, temperature probe and poromeric carry
case
Features
• Autoranging
• Non contact AC voltage detection
• Up to 400A AC current
• Auto power off
• Hold function
• Quality test leads
• Easy one handed operation
• Temperature probe
• Carry case
• Battery included
• Cat III 600V
Specifications
DC voltage: ....................400mV, 4V, 40V, 400V, 600V
AC voltage:.....................4V, 40V, 400V, 600V
AC current: ....................400A
Resistance:....................400O, 4kO, 40kO, 400kO, 4MO, 40MO
Continuity: .....................Audible tone
Diode test: .....................Test current 0.3mA typical
Temperature: ..................-20°C to 760°C
Capacitance: ..................40nF, 400nF, 4µF, 40µF, 100µF
Display: .........................4 digit LCD, 4000 count, backlit
Dimensions:....................˜ 60W x 30D x 195H mm.
Price Each
MET-110 Digital AC Clamp Meter & DMM
DO-5510HA Oxygen Meter
The DO-5510 oxygen meter has a polarographic type oxygen probe with an incorporated Temp. sensor, high precision measurement for Dissolved Oxygen(DO), Oxygen in air
(O2) & Temp. measurement.
Features Include
- Heavy duty dissolved oxygen probe, probe
head can connect with BOD bottle.
- Automatic Temp. compensation from 0 to 50
degC for sensor probe.
- Build in " % SALT " & " Mountain Height " compensation adjustment button.
- Microprocessor circuit.
- Sampling Time: Approx 0.4 seconds
- Dimensions: 185 x 78 x 38mm
- Weight: 265g
- Battery and Soft Carry Case included
Price Each
LUT-011 DO-5510A Oxygen Meter
Page 106 Ocean Controls Catalog 2009
1
$63.59
1
$395.00
OCEAN CONTROLS - TEST EQUIPMENT
MS-7000 Moisture Meter
CD-4303 Conductivity Meter
A portable, easy-to-use wood moisture meter with built-in self calibration. Nine different material groups in memory, providing calibrations for
about 150 different material (wood) types. Built-in self calibration with
manual temperature compensation adjustment.
Product Highlights
* Data hold, Min/Max, Record & Recall functions
* RS232 interface
* 9 Material Species groups in memory
* Remote pin type moisture probe for easy
operation
* Auto shut off & low battery indication
* Moisture probe, contact pins, battery & hard
carrying case included
* Humidity Range: 9 to 30% Moisture Content
* Humidity Resolution: 0.1%
* Humidity Accuracy: +/-4% from 9 to 24%
* Temperature Range: 32 to 122 F / 0 to 50 C
* Temperature Resolution: 0.1 F/C
* Temperature Accuracy: +/-1.5 F / +/-0.8 C
Price Each
LUT-012 MS-7000 Moisture Meter
1
$206.00
PH-207HAH pH Meter
The PH-207AH Meter is portable and provides
fast accurate readings, it comes supplied with a
pH and temperature probe - carry case and full
operating instructions.
Functions include: Max/Min Readings, Dual
Display and Memory Recall.
Measurement Ranges: - 0 to 14 pH x .01 pH
- mV 0 to 1999 mV Humidity
- Temperature 0 to 65 degC
Features
Max, min., Data Hold and RS232 Output
u-P circuit with LCD display
pH, mV, temp., manual temp adj.
Sampling Time Approx. 0.8 second.
Accuracy pH: ± ( 0.03 PH + 2 d)
Operating Temperature: 0 to 50 deg C.
Operating Humidity Less than 80% RH
Price Each
LUT-013 PH-207AH pH Meter
1
$236.00
LX-107HA Lux Meter
The LX-107HA Light Meter is portable and provides fast accurate readings, it comes supplied light probe - carry case
and full operating instructions.
Features
- 2000/20000/100000 Lux Measurement
Ranges
- Data hold, Max, Min, Zero, 2 filters
- Displays in Lux, Ft-candle & % Value
- Tungsten, Fluorescent, Mercury, Sodium, 4
light type select, microprocessor circuit
- Accuracy Lux Measurement ± (5% + 2d)
- Size: 185 x 78 x 38mm
1
$168.00
Digital ORP Meter
1
$272.00
Comes with accelerometer and Carry Case
All industrial machinery vibrates. The level of vibration
is a useful guide to the condition of the machine.
Poor balance, misalignment and looseness of the
structure will cause the vibration level to increase and it
is a sure sign that the maintenance is needed.
Comes with Remote Probe
Used for oxidation/reduction measurement in plating baths, waste water
monitoring and other applications such as AQUARIUM, BEVERAGE,
FISH HATCHERIES, FOOD PROCESSING, PHOTOGRAPHY, LABORATORY, QUALITY CONTROL, SCHOOL & COLLEGES, SWIMMING POOLS etc
Features Include:
* Range : -1,999 mV to +1,999 mV.
* Resolution : 1 mV.
* Easy operation, compact size.
* Water resistance on the front panel.
* All function keys are used the rubber button.
* Large LCD display.
* Temperature: 0 to 60 degress C .
* Hard carrying case included.
Price Each
LUT-022 YK-23RP Digital ORP Meter
1
$110.00
Salt Water Meter
A portable, easy-to-use digital salt water tester. It can measure between
0 to 10%. It has wide applications in water conditioning, aquariums,
beverage, fish hatcheries, food processing, photography, laboratory,
paper industry, plating industry, quality control, schools & colleges.
Features Include:
*Separate electrode, easy operation.
* The portable Salt meter provides fast, accurate
readings, with digital
readability.
* Measuring range : 0 to 10 % salt.
* Automatic temp. compensation for the probe.
* Water resistance on the front panel.
* All function keys are used the rubber button.
* Data hold.
Features Include:
* Frequency range 10 Hz - 1 kHz,
sensitivity relative meet ISO 2954.
* Supply with vibration sensor &
magnetic base, full set.
* Velocity range : 200 mm/s.
* Acceleration range : 200 m/s^2
* RMS & Peak measurement.
* Data hold, Memory ( Max. & Min. ).
* Separate vibration probe.
* Optional data acquisition software.
* Auto shut off saves battery life.
Page 107 Ocean Controls Catalog 2009
Price Each
LUT-010 CD-4303HA Conductivity Meter
Price Each
LUT-014 LX-107HA Lux Meter
Vibration Meter
Price Each
LUT-020 VB-8201 Vibration Meter
The CD4303HA Conductivity Meter is portable and
provides fast accurate readings, it comes supplied
with an ATC conductivity probe - carry case and
full operating instructions.
Functions include: Max/Min Readings, Dual Display and Memory Recall.
Measurement Range: Conductivity: 200 uS, 2mS, 20mS.
Values: 0.1uS to 199.9uS, 0.2mS to 1.999mS,
2mS to 19.99mS.
Resolution: 0.1uS, 0..001mS, 0.01mS.
Accuracy: +/-2% (full scale + 1d)
Temperature: 0 to 60 degress C.
1
$436.00
Price Each
LUT-026 YK-31SA Digital Salt Meter
1
$209.00
OCEAN CONTROLS - TEST EQUIPMENT
Pure Water Meter
4 in 1 Environment Meter
A portable, easy-to-use digital pure water tester
* Applications include: water conditioning, aquariums,
food processing, photography, schools, laboratories,
industry and quality control
* Check the condition of water filters
* Measurement Range: 0-1999 uS
* Automatic temperature compensation from 32 to
122 degF or 0 to 50 degC
* Large LCD display
* Data Hold function
Price Each
LUT-024 YK-30WA Digital Pure Water Test
The Lutron LM-8000 pocket environment anemometer meter measures airflow, temperature,
light and relative humidity. It has a lightweight
low-friction ball vane providing high accuracy
at high & low air velocity. The robust case
incorporates a large easy-to-read display and
wrist strap. Ideal for practically all conditions.
1
$188.00
Sound Level Meter
A portable, easy-to-use sound Level meter. Rugged and ergonomically
built to fit into the palm of your hand.
Features Include:
* Large, easy-to-read LCD display
* Triple range measurement (30 to 80dB, 50 to
100dB, 80 to 130dB)
* A" frequency weighting (same as the human ear)
* Electric condenser microphone for high accuracy
& long-term stability
* Internal 94dB calibration
* Meets IEC 651 Type 2 requirements
* Data Hold & low battery indication
* 9V battery included
* Measuring Range: 35 to 130dB (A)
* Resolution: 0.1dB
* Accuracy: +/-1.5dB
* Frequency: 31.5Hz to 8kHz
* Time Weighting: Fast
* Microphone: 1/2" electric condenser
Price Each
LUT-030 SL-4010 Sound Level Meter
Price Each
LUT-015 LM-8000 Environment Meter
1
$175.00
Prova 123 Calibrator
Specifications
* 4-20mA (1K ohm load, 24V loop supply)
* 0-100.00mV, 0-1.0000V, 0-12.000V ranges
* K, J, E, T Thermocouples (*C and *F)
* Frequency 1-62500Hz
* 0.025% Basic Accuracy
* Easy Key-pad Operation
* Easy Step and Auto Ramp Functions
* 0-20mA, 0-24mA selectable
* 1-100% Input (mA, mV, V)
* Beeper Warning when Output is Open (mA)
1
$179.00
CC421-Current Voltage Calibrator
Features include
* Current Source: 0 to 24 mA, 2 ranges
* Current Measurement: 0 to 24 mA, 2 ranges
* Power & Current Measurement of 2-wire loop: 0 to
24mA, 2 ranges
* DC mV Source: -199.9 mV to +199.9 mV
* Current calibrator drives loads up to 500Ohm
* 13mm LCD display
* current source and measurement accuracy 0.25%
+1d
* voltage source and measurement accuracy 0.25%
+1d
Less than 80% RH
Storage Temperature -40 to 60degC
Dimension: 88mm(L) x 168mm(W) x 26.2mm(H)
Weight 350g/12.34 oz. (Battery included)
Accessories Carrying case x 1
User manual x 1
9V Alkaline Battery
Price Each
LUT-002 Prova 123 Calibrator
Features Include:
*Watt (true rms), VA, Power Factor, ACV, ACA,
VAr, KWh
*DCV,DCA,Ohm & RS232C
*CT & Current Probe Input
Price Each
LUT-032 DW-6090 DESK TOP POWER ANALYSER
1
$233.00
EMF-819 RF EMF TESTER c/- Freq Probe & Hard
Carry Case
DW-6091 PORTABLE TOP POWER ANALYSER
Features Include:
*3 Axis RF EMF tester, general purpose application.
*Frequency range up to 3 GHz
*0 to 199.99 V/m; 0 to 99.999 W/m2; 0 to 9.9999 mW/cm2
Features include
Features Include:
*Watt (true rms), VA, Power Factor, ACV, ACA, VAr, KWh
*RS232C Output & Optional Windows Software
*CT & Current Probe Input
Price Each
LUT-034 DW-6091 PORTABLE TOP POWER ANALYSER
Page 108 Ocean Controls Catalog 2009
1
$749.00
DW-6090 DESK TOP POWER ANALYSER
Sampling Time: Approx 0.4 seconds
Dimensions: 185 x 78 x 38mm
Weight: 265g
Battery and Soft Carry Case included
Price Each
LUT-001 CC-421 Current and Voltage Calibrator
- Selectable m/s, fpm, mph, km/hr or knots
- Shock resistant low-friction ball vane
- Easy to use push button operation
- Data hold freezes current measured value
- Min/max memory since power on
- 18mm LCD display with function indicators
- AAVM-8000 Has a 2 line display for 2 measured values e.g. Air velocity & Temperature and a K type thermocouple input
- Supplied with instructions for use
- Calibration certificates available
- Requires 1 x PP3 9V Battery ALR-61 * Microphone: 1/2" electric condenser
1
$292.00
Price Each
1
LUT-036 EMF-819 RF EMF TESTER c/- Freq Probe & Hard
Carry Case
$496.00
1
$423.00
OCEAN CONTROLS - TEST EQUIPMENT
EMF-822A EMF TESTER c/- Soft Carry Case
EMF-839 EMF TESTER c/- Two Probes &
Hard Carry Case
Features Include:
*0.1mGuass to 199.9mGuass
*30Hz. to 300Hz Bandwith
*9V Battery Power Supply
Price Each
LUT-038 EMF-822A EMF TESTER c/- Soft Carry Case
Features Include:
*3 Axis RF Electromagnetic Field Meter
*100 KHz to 3 GHz, 2 probes, professional
*0 to 199.99 V/m; 0 to 99.999 W/m2; 0 to 9.9999 mW/
cm2
1
$139.00
EMF-827 EMF TESTER c/- Remote Probe &
Soft Carry Case
Features Include:
*0.01uTesla to 2000uTesla(1uTesla = 10mGuass)
*30Hz. to 300 Hz Bandwidth
*9V Battery Power Supply
Price Each
1
LUT-040 EMF-827 EMF TESTER c/-Remote Probe&Soft Carry Case $180.00
Price Each
1
LUT-042 EMF-839 EMF TESTER c/- Two Probes & Hard Carry Case
$1550.00
GS-5800 LEAK DETECTOR and GS400 Ultrasonic Transmitter
Features Include:
*GS-5800 LEAKAGE Detector
*Detects leaks around seals, doors, gaskets
& pipes etc
Price Each
LUT-046 GS-5800 LEAK DETECTOR
LUT-048 GS-400 ULTRASONIC Transmitter
Page 109 Ocean Controls Catalog 2009
1
$259.00
$75.00
OCEAN CONTROLS - TOOLS
TOL-001 Hemostat Curved
TOL-002 Hemostat Straight
125mm or 5" hemostats with a curved
tip. We use them exclusively to hold
small SMD parts in place while soldering. A must have for any handassembly project.
Price Each
TOL-001 Hemostat Curved
125mm or 5" hemostats with a straight tip. We
use them exclusively to hold small SMD parts in
place while soldering. A must have for any handassembly project.
1
$9.00
5+
less 10%
Price Each
TOL-003 Hemostat Straight
TOL-010 Tweezers Curved
High quality polished stainless steel
finish making them rust resistant. Springloaded action making them easier to
use.
Length 125mm
1
$6.00
5+
less 10%
Price Each
TOL-020 Stainless Steel Long Nose Pliers
TOL-030 Stainless Steel Side Cutters
5+
less 10%
A must for people who service 240V
appliances. Rated at 1000V with insulated shaft. Super comfortable rubberised grip. Heat treated chrome vanadium tips for long life.
1
$13.20
5+
less 10%
TOL-040 1000V Insulated Screwdriver - 4mm Flat
Blade
Price Each
TOL-042 1000V Insulated Screwdriver - #1 Phillips
1
$5.18
5+
less 10%
TOL-043 1000V Insulated Screwdriver - #2 Phillips
Specifications:
Length (mm) 100
Phillips #2
Specifications:
Length (mm) 100
Flat Blade 4mm
Price Each
TOL-040 1000V Insulated Screwdriver - 4mm Flat Blade
Specifications:
Length (mm) 80
Phillips #1
A must for people who service 240V appliances. Rated at 1000V with
insulated shaft. Super comfortable rubberised grip. Heat treated chrome
vanadium tips for long life.
A must for people who service 240V appliances.
Rated at 1000V with insulated shaft. Super comfortable rubberised grip. Heat treated chrome
vanadium tips for long life.
Price Each
TOL-043 1000V Insulated Screwdriver - #2 Phillips
1
$4.73
A must for people who service 240V
appliances. Rated at 1000V with insulated shaft. Super comfortable rubberised grip. Heat treated chrome vanadium tips for long life.
Specifications:
Length (mm) 150
Flat Blade 6.5mm
Price Each
1
TOL-041 1000V Insulated Screwdriver - 6.5mm Flat Blade $5.18
1
$5.18
5+
less 10%
5+
less 10%
TOL-041 1000V Insulated Screwdriver - 6.5mm Flat
Blade
Page 110 Ocean Controls Catalog 2009
1
$13.20
TOL-042 1000V Insulated Screwdriver - #1 Phillips
High quality polished stainless steel
finish making them rust resistant. Springloaded action making them easier to
use.
Length 125mm
Price Each
TOL-030 Stainless Steel Side Cutters
5+
less 10%
TOL-020 Stainless Steel Long Nose Pliers
Basic 110mm or 4.5" high-carbon
stainless steel curved tweezers for holding small components during soldering.
These non-magnetic tweezers are perfect for SMD components and fine adjustments. We use them extensively for
hand placement of SMD devices and
general board rework.
Price Each
TOL-010 Tweezers Curved
1
$9.00
TOL-044 1000V Insulated Screwdriver Set - 6pc
This set of screwdrivers is ideal for people who
service 240V appliances. They are rated at
1000V and the shaft is insulated to the tip. Includes 3 slotted and 2 phillips screwdrivers, plus
a 240V neon tester.
Price Each
TOL-044 1000V Insulated Screwdriver Set - 6pc
5+
less 10%
1
$20.86
5+
less 10%
OCEAN CONTROLS - TOOLS
TOL-045 1000V Insulated Electrician Tool Set - 9pc
This insulated toolkit is ideal for electricians, technicians and those working on mains powered equipment. It
includes cutters, pliers, wire strippers,
5 screwdrivers plus a neon test driver,
all in a handy carry case. Also includes 2 rolls of insulation tape.
TOL-051 Coaxial Crimp Tool T1555
Adjustable crimp tension with ratchet action
handles. Heavy duty all metal construction.
Suits RG58, Fibre Optic, SMA, SMB and RG174
connectors. Suitable for use with connectors fitted to multi-core RGB
coaxial cable ie Altronics BNC P 0525 (with 5.3mm OD ferrule)
Price Each
TOL-051 Coaxial Crimp Tool T1555
Price Each
TOL-045 1000V Insulated Electrician Tool Set - 9pc
1
$53.64
1
$41.77
5+
less 10%
5+
less 10%
TOL-052 BNC TNC F Crimp Tool to Suit RG-11 Cable
TOL-050 Coaxial Crimping Tool T1554
Suits coaxial cable connectors. Adjustable crimp tension with
ratchet action handles. Heavy duty all metal construction. Suits
RG6, RG58 and RG59
Suitable for crimping RG6 & RG11 size connectors. Include crimp jaws for RG6, RG11 & RG11
centre pin. Adjustable crimp tension. Heavy duty
all metal construction.
Price Each
TOL-052 BNC TNC F Crimp Tool to Suit RG-11 Cable
Price Each
TOL-050 Coaxial Crimping Tool T1554
1
5+
$40.86 less 10%
1
$41.77
5+
less 10%
TOL-053 Crimptool - For Foxtel F
This coaxial crimper is suitable for use with P
0486 Foxtel approved F connector. It crimps
ferrules with overall diameter of 10.8mm. Adjustable crimp tension with ratchet action handles.
All metal construction. Suits RG6, RG11 and RG59.
Price Each
TOL-053 Crimptool - For Foxtel F
Page 111 Ocean Controls Catalog 2009
1
$41.77
5+
less 10%
OCEAN CONTROLS - AUDIO
20 Second Voice recorder module
120 Second Voice recorder module
This voice recording module offers solid state storage and playback of
a single 20 second message and can be extended up to 30 seconds
with a slight degradation of sound quality.
Features:
- Non volatile flash memory
- No battery backup required
- 2 button operation REC/PLAY
- Low Power Consumption
- LED Indication
- Built in mic
- 5V Operation
Introducing the new kit 189. Uses a
17120 Second Voice Recorder
Module. Non-volatile multi message
recorder using ISD chips. Just
change one resistor for longer duration. Standalone operation using
just six onboard bottons. Record via
built-in microphone or external line
in. Speaker and line out connector.
SPI interface. 8-24 VDC.
Only requires Speaker
Price Each
KIT-363 20 Second Voice module
1
$17.50
5+
less 10%
10W+10W Stereo Amplifier Module
The TDA2009A is a monolithic hi-fi
quality audio power amplifier IC with
dual class AB outputs, designed for
high quality stereo applications.
Kit uses the data book application
circuit and gives a gain of 36dB. It
delivers 10 watts per channel into 4
Ohm speakers with a 24V DC supply. Can be fitted into existing equipment if required.
Price Each
KIT-189 120 Second Voice module as Kit
KTA-189 120 Second Voice module as Kit
1
$45.00
$64.00
6-10W Stereo Amplifier Module
This hi-fi quality class AB
audio amplifier is based
on the TDA2005 IC with
output current and thermal
protection. 8-18 VDC Supply with 1-2 Amp capability
required. THD <0.1%, S/N
Ratio >80dBA, Gain
<30dB
Supply range: 8 - 28V DC. Screw terminal block connections. Heatsink
provided. PCB: 45 x 80mm
Price Each
1_
5+
KIT-088 10W+10W Stereo Amplifier Module as Kit
$23.00 less 10%
KTA-088 10W+10W Stereo Amplifier Module Assembled $39.00 less 10%
50W Mono Hi Fi Power Amplifier
Price Each
KIT-143 6-10W Stereo Amplifier Module as Kit
KTA-143 6 -10W Stereo Amplifier Module Assembled
1
5+
$26.00 less 10%
$42.00 less 10%
50W RMS Amplifier Module Kit
High power, hi-fi quality class AB audio amplifier module using a
TDA7294 IC. Provides an impressive 50W RMS into 8 Ohm or 82W
RMS into 4 Ohm with only 0.1% THD.
Mute and Standby are brought out to
connection pads on PCB. IC has internal
thermal protection.
Space is provided on the PCB for mounting a 1.4°C/W heatsink (not provided).
All components including IC insulation
bush, screws, nuts & washers and TO-3
silicon-impregnated insulating washer are
provided. Heat sink, speaker, cables and
+/-30V power supply not provided. Solder
pad connections. PCB: 84x83mm
(heatsink area of PCB is 37x83mm but can overhang if required).
Performance:
Output Power: 50W into 8Ohm; 70W into
4Ohm.
Music Power: 77W into 8Ohm; 105W into
4Ohm.
Frequency Response: -1dB at 14Hz and
70kHz (at 1W -see Fig.1).
Input Sensitivity: 0.875V for 50W into
8Ohm.
Harmonic Distortion: <0.05% from 20Hz
to 20kHz; typically <0.003%.
Signal-to-Noise Ratio: -114dB unweighted (22Hz to 22kHz); -119dB Aweighted, both with respect to 50W into 8Ohm.
Damping Factor: >140dB at 100Hz & 1kHz, with respect to 8Ohm and
without PTC thermistor.
Protection: Fuses plus "PTC Fuse" PTC thermistor.
Stability: Unconditional
Price Each
1
5+
KIT-106 50W Mono Hi Fi Power Amplifier as Kit
$45.00 less 10%
KTA-106 50W Mono Hi Fi Power Amplifier Assembled $65.00 less 10%
Price Each
KIT-120 50W RMS Amplifier Module as Kit
KTA-120 50W RMS Amplifier Module Assembled
Page 112 Ocean Controls Catalog 2009
1
5+
$52.24 less 10%
$77.50 less 10%
OCEAN CONTROLS - AUDIO
135W RMS Amplifier Module Kit
(SC August ‘08) This 135W amplifier module
produces incredibly low levels of distortion
even at high power outputs. The class AB
design runs much cooler than genuine class
A amplifiers, yet performance has not been
sacrificed. It produces 135W into 8 Ohm or
200W into 4 Ohm with distortion levels
around 0.008%. Heatsink is not supplied, we
suggest the H 0545 diecast heatsink for a
professional finish when mounted in a case.
Price Each
KIT-151 135W RMS Amplifier Module Kit
KTA-151 135W RMS Amplifier Module Assembled
Ever wanted to play your guitar through your
headphones along with your favourite music at
the same time? Well now you can with the
guitar jammer. Just plug the CD and guitar into
this kit and you can play along with the best of
them.
1
5+
$83.59 less 10%
$108.50 less 10%
DSP Musicolour Musical Lights Kit
(SC June/July ‘08) Accepts audio input signals
and drives coloured lights "in tune" with the
music. Four output channels respond to different audio frequency bands and the light brightness is in proportion to the amplitude of the
frequency components. A LED menu display is featured on the front
panel and this also functions as a spectrum analyser or VU meter.
Price Each
1_
5+
KIT-803 DSP Musicolour Musical Lights Kit
$199.09 less 10%
KTA-803 DSP Musicolour Musical Lights Kit Assembled $229.00 less 10%
Page 113 Ocean Controls Catalog 2009
Guitar Jammer Headphone Amplifier Kit
Features:
Low noise circutry
Separate CD & Guitar volume controls
Frequency response: -3db @ 30Hz and 70Hz
9V battery operated or 9VDC plugpack operated
Suplied with professionally finished & screened case
Price Each
1
KIT-536 120 Guitar Jammer Headphone Amplifier Kit
$36.55
KTA-536 120 Guitar Jammer Headphone Amplifier Assembled $52.50
Page 114 Ocean Controls Catalog 2009
OCEAN CONTROLS - THE FINE PRINT
Paying For Items
All our prices are in Australian Dollars. You can check the exchange rate by going to http://www.x-rates.com Prices on in our catalog do not include
GST (Goods and Services Tax). 10% GST applies to goods delivered in Australia.
Australian GST is not paid on shipments despatched to an international destination.
At this stage we accept Mastercard, Visa and American Express credit cards online. We only accept Visa and Mastercard for phone orders. We will
accept payments by Western Union. We will also accept a cheque or money order from an Australian based individual or company. If you wish to
make a purchase using a credit card but do not want to use our online ordering system then you can do a transaction over the phone or download
our order form and fax or email it to us.
Any international customer wishing to pay by bank transfer will be required to pay all bank fees including those of our bank (approximately
AUD$25).
Company Orders
If you are from an Australian Government Organisation we will accept an official order with a letterhead on it.
If you are a company with an ABN number you can apply to set up an account with us.
Delivery to Australian Addresses and New Zealand
All deliveries in Australia are done by Express Post which means you will receive it usually the next day or the following day at the latest. We deliver
by express post as it has a tracking number system.
If you want delivery by normal post you will have to ring us to determine cost of postage. For those who request normal postal service, we accept no
responsibility for the length of delivery time or any loss of packages
Packages to New Zealand are delivered by air mail and take approximately 4-7days
Delivery to International Addresses using Air Mail
We normally deliver goods by air mail. Typical delivery times are
UK and USA 6-10 days.
Canada and Europe 2 weeks
South Africa 2-3 weeks
We charge AUD$22.50 which includes insurance. Because the item is insured you will be required to sign for it at your post office. If your country is
not listed when you fill out the purchase form on our website then it means Australia Post does not insure goods to your country and you will be
prevented from making an online purchase. There is no tracking number issued with Air Mail.
Please note import Custom Duty/Taxes if payable are your responsibility.
Delivery to International Addresses using EIC, DHL or Fedex
If you want faster delivery then we can deliver it by Australian Post Express International Courier or EIC. Normally it costs AUD$45 for most small
parcels and will take 3-4 days. You will be issued with a tracking number. Please contact us to arrange payment for the EIC option
If you want goods delivered by DHL or Fedex then you must have an account with them.
Please note import Custom Duty/Taxes if payable are your responsibility.
Faulty Goods and Warranty
Where such goods have been supplied we undertake to repair or replace them as quickly as possible. Contact us with a description of the fault and
we will issue an authorisation to return the goods.
Our warranty period is 3 months from the date of purchase or longer as stated in our catalog or on our website.
Once a kit is under construction all warranty is void as we cannot guarantee the workmanship of the person assembling the unit. If a kit has been
purchased assembled and tested from us then a 3 month warranty applies.
Warranty is subject to us being satisfied that a defect was caused by defective workmanship or materials and was not caused by or was not substantially contributed to by other factors beyond our control including incorrect installation, alterations or modifications of the product not recommended by the manufacturer.
Returns Policy
If you are dissatisfied with our goods you may return them within 7 days of the dispatch date. Contact us for an authorisation and we will refund your
purchase. All returned goods must in "as sold" condition including all packaging, documentation, invoices etc. Please note
The product returned may attract a 15% restocking fee.
The customer must pay the delivery costs.
Non standard, custom made or a specially manufactured product or imported product is not returnable.
Semiconductors are not refundable.
Peter Simmonds
Managing Director
Page 115 Ocean Controls Catalog 2009
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising