Instruction Manual

Instruction Manual
1
Instruction Manual
Reizen Atomic Radio-Controlled USB-Charge Analog Talking Watch
(USA-Euro Multi-Band)
#704066
Your Atomic USB-Charge Analog Talking Watch is a multi-band, radio-controlled
watch. It is able to pick up a time-setting signal from the USA (excluding Alaska and
Hawaii), UK, GERMANY, and JAPAN (60 KHz only). Wherever there is no accessible
atomic signal, the time is easily set manually.
Your watch is time-synchronized to the Atomic Clock (which measures each
second of time as 9,192,631,770 vibrations of a cesium 133 atom in a vacuum) and gives
time, which is accurate to 1 second every million years. Your radio-controlled watch
even accounts automatically for daylight saving time (when applicable).
Automatic Time Setting
Your talking radio-controlled watch receives a user-selected Atomic Clock signal
automatically at 3:00 AM every night. After reception of signal it will show the official
local time on the watch. Everything is done automatically. However, your watch can
also be set manually.
Button Functions:
S1
● Press
S1 (2 o’clock button) to announce Hour and Minute
● Press S1 two (2) times to announce the Date
● Press S1 three (3) times to announce reception status
NOTE: If time signal reception was successful, the watch will say “[Country Name]”
followed by “Time Updated.” If signal reception failed, the watch will say “[Country
Name]” followed by “Time Not Updated.”
2
S2
Push S2 (4 o’clock button) one (1) time to check alarm time setting and to determine if
the alarm is set to ON or OFF (the watch says the alarm time followed by either “Alarm
is ON” or “Alarm is OFF”)
●
Crown
● Use
to reset all hands to 12:00:00 position
NOTE: When the crown is pulled out, the watch stops immediately.
Battery Power Level Check
1. Press S2 two (2) times to show the battery power level.
NOTE: Battery Power Level is indicated by second hand position:
High = Second hand points to 8 o’clock
Medium = Second hand points to 7 o’clock
Low = Second hand points to 6 o’clock
Low Battery Alert
When Battery Power Level is low, the watch generates a “beep-beep” sound before it
announces the time, calendar, reception status, or alarm.
Please recharge the watch when you hear the “beep-beep” sound.
How To Charge Watch
When Battery Power Level is low, the seconds hand runs 2 steps every 2 seconds. When
this is the case, all button operations and signal reception will not function. If the watch is
not charged in time, the hands stop at 12 o’clock to conserve the remaining battery power.
The watch should be charged as soon as possible.
The charging input socket of the watch is on the back of the watch. Connect the provided
USB charging cable to a computer USB port or USB AC Adapter (not included) and the
other end into the watch.
The watch makes a chirping sound when the plug is correctly inserted and charging
begins.
Correct Watch Positions For Time Signal Radio Reception
Your watch should be positioned as follows and put near a window during signal
reception or you will not be able to get the best reception result.
As shown below, for metal case watches with a metal band, the watch band should not
make contact with the back of the watch case (insert a non-metal object to serve as a
3
spacer between the case back and the metal band) otherwise the metal band will interfere
with time signal reception.
Country Signal Selection
You can set your watch to get USA (excluding Alaska and Hawaii), UK,
Germany, or Japan (60 KHz) signal.
After you change to a new country, the watch will run according to the new
time zone. Please wait when the second hand is fast running until it resumes its
normal running speed.
Select USA, UK, Germany, or Japan (60 KHz only) signal:
NOTE: USA users need to set the watch to one of the USA Time Zones as listed
below.
1. Hold S2 (4 o’clock button) while the watch is running in normal time mode for more
than 5 seconds until the watch says “Set alarm, press 2 o’clock button (S1) to set.”
2. Push S2 (4 o’clock button) another three (3) times until the watch says “Global signal
selection, only when you visit this country. Press 2 o’clock button (S1) to set.”
3. Press S1 (2 o’clock button) and the watch will say “Press 2 o’clock button (S1) to set,
4 o’clock button (S2) to confirm.”
4. Press S1 (2 o’clock button) to select either:
UK
Germany
Japan (60 KHz only)
USA, Pacific
USA, Mountain
USA, Central
USA, Eastern
5. Press S2 (4 o’clock button) to confirm after a new country has been selected.
4
6. After the confirmation, the watch will run to the local time of the country that you
have selected. Wait until the watch stops fast running and resumes normal running.
7. During “Summer Time” or “Daylight Saving Time” there will be a one hour
difference after you have set the watch to a new country. This will be corrected after
the local time signal reception has been updated.
8. The watch will synchronize with the local atomic clock automatically at midnight
starting from 3:00 AM so you have to make sure that the right country has been set or
the watch will not be able to locate the local radio time setting signal.
Manual Signal Reception
The watch must be set to the correct country before using manual signal reception.
Refer to the “Country Signal Selection” section for details.
Place the watch on a table near a window to obtain manual signal reception. Please pay
attention to the position of the watch. You must put the watch on the table according to
the position shown on the picture below or the watch will not be able to acquire the time
signal.
While the watch is running in normal time mode:
1. Hold S1 (2 o’clock button) until the second hand stops.
2. The watch takes about 5 to 14 minutes to pick up the radio signal. Please be patient
and wait until the watch has finished the signal receiving procedure.
3. After signal reception, the watch will show the time again after the fast running of the
second hand has stopped and it has resumed normal running.
4. Push S1 (2 o’clock button) three (3) times after the watch has resumed normal
running to check reception status.
- If time signal reception was successful, the watch says “[Country Name]”
followed by “Time Updated.”
- If time signal reception failed, the watch says “[Country Name]” followed by
“Time Not Updated.”
Setting Daily Alarm
1. Hold S2 (4 o’clock button) for more than 5 seconds while the watch is in the normal
time mode until the watch says “Set alarm, press 2 o’clock button (S1) to set.”
2. Press S1 (2 o’clock button), the watch says “Press 2 o’clock button (S1) to set hour, 4
o’clock button (S2) to confirm.”
3. Press S1 (2 o’clock button) to set alarm hour.
4. Press S2 (4 o’clock button) after alarm hour is set.
5. The watch says “Press 2 o’clock button (S1) to set minute, (4 o’clock button (S2) to
confirm.”
6. Press S1 (2 o’clock button) to set alarm minute.
7. Press S2 (4 o’clock button) to confirm and exit after you have set the alarm minute.
8. After confirmation, the watch will say the alarm time (Hour and Minute) that you
have set.
5
9. To check your alarm time setting, press S2 (4 o’clock button) one (1) time while the
watch is running normally.
NOTES:
1. The alarm will beep for 30 seconds; you can turn off the alarm with a push of any
button.
2. The alarm is a daily alarm, so even if you have turned off the beeping sound, the
alarm will beep on the next day again. If you want to turn off the daily alarm, you can
follow the Alarm On/Off setting directions below.
3. Every time when a beep is off, it will speak the Alarm Time.
Turning Alarm ON/OFF
1. Hold S2 (4 o’clock button) while the watch is in the normal running mode for more
than 5 seconds until the watch says “Set alarm, press 2 o’clock button (S1) to set.”
2. Press S2 (4 o’clock button) one (1) more time, the watch says “Alarm ON/OFF, press
2 o’clock button (S1) to set.”
3. Press S1 (2 o’clock button), the watch says “Press 2 o’clock button (S1) to On/Off, 4
o’clock button (S2) to confirm.”
4. Press S1 (2 o’clock button).
5. Every press of S1 (2 o’clock button) toggles the alarm ON and OFF. The watch says,
“Alarm On” when it is set to ON; “Alarm OFF” when it is set to OFF.
6. Press S2 (4 o’clock button) to confirm and exit.
Hourly Time Announcement (Chime) ON/OFF
(When Chime is ON, the watch announces the “[Hour]” every hour)
1. Hold S2 (4 o’clock button) while the watch is in the normal running mode for more
than 5 seconds until the watch says “Set alarm, press 2 o’clock button (S1) to set.”
2. Press S2 (4 o’clock button) two (2) more times, the watch says “Chime ON/OFF,
press 2 o’clock button (S1) to set.”
3. Press S1 (2 o’clock button), the watch says “Press 2 o’clock button (S1) to On/Off, 4
o’clock button (S2) to confirm.”
4. Press S1 (2 o’clock button).
5. Every press of S1 (2 o’clock button) toggles the hourly "chime" alert ON and OFF.
The watch says, “Chime On” when it is set to ON and “Chime OFF” when it is set to
OFF.
6. Press S2 (4 o’clock button) to confirm and exit.
7. After a Chime alert is confirmed to be ON, the watch will announce the “[Hour]”
every hour.
Manual Time Setting (for country without time signal)
(You should use this function when you travel to, or live in, a country with no time signal.
You must set your watch to your local time when you return from countries without a
radio time signal or your watch will be unable to pick up the time signal at 3:00 AM as
there is often a time difference between those countries and your country.)
6
Set Time
1.
Hold S2 (4 o’clock button) while the watch is in normal Time Keeping mode for
more than 5 seconds until the watch says: "Set alarm, press 2 o’clock button (S2)
to set."
2.
Push S2 (4 o’clock button) four (4) more times, until the watch says: "Set Time,
press 2 o’clock button (S2) to set."
3.
Press 2 o’clock button (S1).
4.
The watch says: "Press 2 o’clock button (S2) to set hour, 4 o’clock button (S4) to
confirm."
Press S1 (2 o’clock button) to set Hour. Listen very carefully to the watch to make
certain that AM or PM has been set correctly.
5.
Press S2 (4 o’clock button) to confirm after you have set the Hour.
6.
The watch says: "Press 2 o’clock button (S1) to set minute, 4 o’clock button (S2)
to confirm."
7.
Press S1 (2 o’clock button) to set Minute.
8.
Press S2 (4 o’clock button) to confirm after the minute is set.
9.
After confirmation, the watch fast spinning to match the time announcement
automatically.
10.
Wait until the watch resumes normal running.
NOTE: Your watch is able to set Date, Day, Month, and Year automatically only
when the radio time signal is available.
Setting Watch To Sleep Mode
You should do this only if you will leave your watch unused in your drawer for a long
period of time.
1. While the watch is running normally, press and hold without releasing S1 (2 o'clock
button).
2. Press and hold S2 at the same time (holding down 2 buttons now) until the second
hand is fast spinning.
3. Release all buttons. The watch will spin to 1:00:00 and then sleep there.
To Wake Up Watch
Press any button for 2 seconds. After the watch is woken up, it will spin to match the
internal time. Wait until the watch resumes normal running.
TROUBLESHOOTING:
Your watch is a delicate and precise instrument. Although uncommon, sometimes hard
knocks or vibrations can cause the hands to move irregularly and display the incorrect
time, even though the internal clock is keeping accurate time. You may notice this when
the time announcement does not match the position of the watch hands. To correct this
situation, you will need to reset the watch hands using the following procedures.
7
Reset Watch Hands
1. Wait until the second hand ticks to the 12 o’clock position and pull out the crown
immediately so that the second hand stops at 12.
2. Turn the crown to set Hour and Minute hands to 12 o’clock.
3. After all hands are set to 12:00:00, hold S1 (2 o'clock button) for 5 seconds and then,
4. Push in the crown.
5. The watch hands spin to match the internal time and resume normal running when
the time matching is finished. After the watch resumes normal running, the watch
hands will match the internal time-keeping of the watch.
Reset Watch To Atomic Radio Signal
You can reset the watch as follows:
1. While the watch is running, pull out the crown to stop the second hand at the 12
o’clock position.
2. Turn the crown to set Hour and Minute hands to 12 o’clock. Now all hands are set to
12:00:00.
3. Do not push in the crown but press and hold S2 (2 o'clock button) for 15 seconds and
then;
4. Push in the crown. Your watch will not run after the crown is pushed in.
NOTE: Place your watch near a window to get a time setting signal. The watch will start
to update. It will continue updating the signal over the next 24 hours if the first time
setting signal reception is not successful. The hands will move to the correct time after
receiving a valid time signal.
Watch Not Receiving Time Signal
Reasons for not being able to receive the Time Signal include:
-Being outside of the USA, UK, Germany or Japan (60 KHz) radio signal area
-Being in an area with building construction
-Metal objects or structures blocking the radio signal
-Interference by computer monitor or TV
NOTE: Ensure that the watch is left by a window, as this gives the best reception. You
may have to try different windows in the house to see which works best. You can test this
using the reception status test described earlier. Please note that reception is always better
at night.
If your watch is unable to make contact with the radio signal, it will continue to function
in the same way as a standard watch. The time will then be corrected the next time your
watch receives the radio time setting signal.
Replacing the battery
The built-in rechargeable battery is not user-replaceable. In the event it appears necessary
to replace the battery, please contact Reizen for service. See "Manufacturer's Limited
Warranty" section.
8
After Battery Replacement
1. After battery replacement, the second hand starts to run when the crown is pushed in.
2. Wait until the second hand is at the 12 o’clock position and pull out the middle crown
immediately so that the second hand stops there.
3. Turn the crown to set Hour and Minute hands to 12 o’clock. Now all hands are set to
12:00:00.
4. Push in the crown. Your watch will not run after the crown is pushed in.
5. Place your watch near a window to get a time setting signal. The watch will start to
update. It will continue updating the signal over the next 24 hours if the first time
setting signal reception is not successful. The hands will move to the correct time
after receiving a valid time signal.
6. After the watch is able to set the time automatically, you need to set the Time Zone
according to the following instructions:
 If you are a USA user, set USA Time Zone. Go to “Country Signal Selection"
section and see USA Time Zones for details.
 If you are a Japan, UK, or Germany user and provided that your watch is
bought locally, you do not need to set time zone on your watch as it has been
set to your local time zone before leaving the factory.
NOTE: If the watch does not show the right time after battery replacement, please reset
your watch according to the “Reset Watch” sections.
ADDITIONAL NOTES:
1. Whenever the crown is pulled out, the watch hands stop while the internal clock still
runs. After you push in the crown, the watch will fast spin to match the internal time
automatically.
2. When the watch is fast spinning, do not pull out the crown. If the crown is pulled out
while the watch is fast spinning, the second hand will stop. After you push in the
crown, the watch will resume spinning to match the internal time.
Manufacturer's Limited Warranty
Reizen guarantees this talking watch to be free of any manufacturer's defects for a period
of one year from the date of purchase.
We will fix or replace (at our discretion) your defective watch at no charge to you.
Customer abuse, neglect, or any attempt to open and repair the watch voids this warranty.
For warranty service, please return the watch to the address below, postage paid, with
your original receipt. Include a payment of $5.50 to cover the return shipping. All
returned watches are subject to evaluation and approval.
REIZEN
P.O. Box 3312
Farmingdale, NY 11735
Phone: 1-800-522-6294
Reizen is a preferred distributor of quality REIZEN products.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement