Yamaha | YSTMS35D | Owner's Manual | YST-MS35D - Yamaha Corporation

UCA
POWERED MULTIMEDIA SPEAKERS
YST-MS35D
OWNER’S MANUAL . . . 1
MODE D’EMPLOI . . . . 11
V
U
L
O
E
M
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
CAUTIO N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
IMPORTANT!
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
SAFETY INSTRUCTIONS
1
2
Read Instructions — All the safety and operating
instructions should be read before the unit is operated.
10 Power Sources — The unit should be connected to
Retain Instructions — The safety and operating
instructions should be retained for future reference.
11 Power-Cord Protection — Power-supply cords
3
Heed Warnings — All warnings on the unit and in
the operating instructions should be adhered to.
4
Follow Instructions — All operating and other
instructions should be followed.
5
Water and Moisture — The unit should not be used
near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool, etc.
6
Carts and Stands — The unit should be used only
with a cart or stand that is recommended by the
manufacturer.
6A An unit and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
unit and cart combination to overturn.
7
8
9
ii
Wall or Ceiling Mounting — The unit should be
mounted to a wall or ceiling only as recommended
by the manufacturer.
Ventilation — The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may
block the ventilation openings; or placed in a built-in
installation, such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
Heat — The unit should be situated away from heat
sources such as radiators, stoves, or other appliances that produce heat.
a power supply only of the type described in the
operating instructions or as marked on the unit.
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords at
plugs, convenience receptacles, and the point
where they exit from the unit.
12 Cleaning — The unit should be cleaned only as recommended by the manufacturer.
13 Nonuse Periods — The power cord of the unit
should be unplugged from the outlet when left
unused for a long period of time.
14 Object and Liquid Entry — Care should be taken so
that objects do not fall into and liquids are not
spilled into the inside of unit.
15 Damage Requiring Service — The unit should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled
into the unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the enclosure
damaged.
16 Servicing — The user should not attempt service
the unit beyond those means described in the operating instructions. All other servicing should be
referred to qualified service personnel.
17 Power Lines — An outdoor antenna should be
located away from power lines.
18 Grounding or Polarization — Precautions should be
taken so that the grounding or polarization is not
defeated.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party:
Address:
Telephone:
FAX:
Type of Equipment:
Model Name:
Yamaha Corporation of America
6600 Orangethorpe Ave.
Buena Park, CA90622
714-522-9011
714-527-5782
Powered Multimedia Speakers
YST-MS35D
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A)
1.
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications
not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2.
IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3.
NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will
not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the
product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America 6600 Orangethorpe Ave. Buena Park, CA90622, U.S.A.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003.
POUR LES CONSOMMATEURS CANADIENS
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST
CONFORME À LA NORME NMB-003 DU CANADA.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most
out of your equipment by playing it at a safe level. One
that lets the sound come through loud and clear without
annoying blaring or distortion – and, most importantly,
without affecting your sensitive hearing.
Since hearing damage from loud sounds
is often undetectable until it is too late,
YAMAHA and the Electronic Industries
Association’s Consumer Electronics
Group recommend you to avoid prolonged
exposure from excessive volume levels.
iii
Cautions
Please read the following operating precautions before use:
•
If the YST-MS35Ds are located close to fluorescent or neon lights, a slight hum may be heard. In
this case, relocate the YST-MS35Ds away from the
light.
•
Although the YST-MS35D speakers are magnetically shielded, keep floppy disks and tapes away
from them.
•
Never open the cabinet. If a foreign object drops
into the set, contact your dealer, and do not use the
YST-MS35Ds. Otherwise, you may cause a fire.
The YST-MS35Ds may cause picture distortion
when located close to a television or computer
monitor. In this case, move them away a short distance.
•
•
Do not expose the YST-MS35Ds to temperature
extremes, direct sunlight, excessive dust, humidity,
or vibration.
Avoid sources of hum (transformers, motors). To
prevent fire or electrical shock, do not expose to
rain and water.
•
•
Position the YST-MS35Ds on a level, stable surface. Do not drop the YST-MS35Ds, apply excessive force to their controls, or put heavy items on
top of them.
Do not use force on switches, knobs, or cables.
When you move the YST-MS35D, first turn off the
power to the speakers, then disconnect the AC
adapter from the AC receptacle and the cables
from the connected devices.
•
Always turn the volume control counterclockwise
to the minimum before starting to play the audio
source: increase the volume gradually to an appropriate level after the playback has started.
•
When you disconnect the AC adapter from the AC
receptacle, hold the plug, not the cord.
•
If you plan not to use the YST-MS35Ds for a
while, disconnect the AC adapter from the AC
receptacle.
•
Always disconnect the AC adapter from the AC
receptacle before making any connections.
•
The YST-MS35Ds do not contain any user serviceable parts. Refer all servicing to your Yamaha
dealer.
•
•
Do not place small metal objects on the speakers.
Otherwise, the object may fall, possibly causing an
injury.
•
Since this unit has a built-in power amplifier, heat
will radiate from the rear panel. Therefore, place
the unit away from walls, allowing enough space
above, behind, and on both sides of the unit. Also,
do not position with the rear panel facing down on
the floor or other surface. (Subwoofer only)
•
Do not obstruct the port with your hand or a foreign object.
•
To protect the YST-MS35D speakers, avoid microphone feedback, continuous and excessive output
from electronic musical instruments, and excessive
signal distortion.
Intel and Pentium are registered trademarks and MMX
is a trademark of Intel Corporation.
Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.
All other trademarks are property of their respective
owners.
Table of Contents
Cautions .....................................................................1
Introducing the YST-MS35D Speaker System.......2
System Requirements ...............................................2
Controls & Connectors.............................................3
Installing and verifying the YST-MS35D speaker
device drivers.............................................................4
Installing the device drivers ....................................4
Verifying the installation of device drivers.............5
Re-installing the Device Driver ..............................6
1
Ensuring the output of audio data from the
USB port................................................................. 7
Connecting to a non-USB system............................ 8
Enjoying your YST-MS35D Speaker System ........ 8
Adjusting the Volume, Bass, and Treble................ 8
Playing Music CDs................................................. 8
Troubleshooting........................................................ 9
Speaker angle and Non skid pad........................... 10
Specifications .......................................................... 10
English
Introducing the YST-MS35D Speaker System
Thank you for purchasing the Yamaha YST-MS35D Powered Multimedia Speakers.
The YST-MS35D Multimedia Speakers utilize Advanced Yamaha Active Servo Technology, which offers exceptionally high performance, allowing these compact speakers to produce a rich bass sound. They also employ USB technology to create a computer-based listening environment that is far superior to conventional multimedia speakers.
They reproduce a clearer sound, with less noise and distortion, and never require a soundcard!
The YST-MS35D includes three speaker components: a left satellite speaker, a right satellite speaker, and a subwoofer.
Notes: Do not connect the PC and the subwoofer using the USB cable before installing the YST-MS35D speaker
device driver.
1
USB Cable
3.5 mm stereo mini plug cable
USB
INPUT
2
3
Face this marking
upward to connect
the USB cable to
the port.
TO RIGHT
SPEAKER
1
INPUT
2
INPUT
TO LEFT
SPEAKER
0
10
BASS
LEFT
SATELLITE
SPEAKER
AC adapter
DC 15V
RIGHT
SATELLITE
SPEAKER
SUBWOOFER
1 3.5 mm stereo mini plug cable × 1 (Accessory)
2 USB cable × 1 (Accessory)
3 AC adapter × 1 (Accessory)
The package also contains a CD-ROM and eight non-skid pads to attach to the bottom of the satellite speakers.
Warning: Please inspect the package contents thoroughly for damage. If any item is missing or damaged, please
contact the dealer from whom you purchased the YST-MS35D.
System Requirements
For digital audio streaming using a USB connection:
OS: Microsoft Windows 98
CPU: 200 MHz or faster Intel Pentium MMX processor or equivalent
HDD: At least 10 MB available space
CD-ROM drive for driver installation
USB port compatible with USB standards ver 1.0
2
Controls & Connectors
Subwoofer rear panel
Right satellite speaker top side
USB
INPUT
1
VOLUME
7
8
TO RIGHT
SPEAKER
2
1
INPUT
2
INPUT
3
TO LEFT
SPEAKER
4
0
10
BASS
5
DC 15V
6
1 USB INPUT
Use the included USB cable to connect this port to the USB port on the computer.
2 TO RIGHT SPEAKER
Connect the 8-pin cable from the right satellite speaker to this connector.
3 INPUT 1/2
You can input two audio sources to the speaker system from these input jacks. For example, you can connect the
output of a CD-ROM player and a personal computer here. The two audio sources are mixed together by the
speaker system.
4 TO LEFT SPEAKER
Connect the RCA plug cable from the left satellite speaker to this connector.
5 BASS control
Allows you to adjust the volume level of the subwoofer.
A typical (recommended) setting is the position between one o’clock and two o’clock.
Rotating the control clockwise will increase the volume level, and rotating the control counter-clockwise will
decrease the level.
6 DC connector
Connect the included AC adapter to this connector. Press the
to turn the power on or standby.
(standby/on) button on the right satellite speaker
7 VOLUME control
Allows you to adjust the volume level of the entire speaker system.
Rotating the control clockwise will increase the volume level, and rotating the control counter-clockwise will
decrease the level.
8
3
(standby/on) button/indicator
Press this button to turn on the power to the speaker system. Its indicator lights up. Press the button again to turn
the speaker system to standby mode.
Before pressing this button, make sure that the VOLUME control setting is lowered. A small electrical current
flows through the speaker system even if the standby/on button is turned off.
Please follow these steps to install the Yamaha YST-MS35D speaker device drivers in your Windows 98 system
using the included CD-ROM, and verify that Windows 98 recognizes the installed device drivers and that CD audio,
sound generated while using software, and system sounds from the computer will be output via the USB port.
Installing the device drivers
Notes:
•
Do not connect the PC and the subwoofer using the USB cable before installing the YST-MS35D device
drivers. If you accidentally connect them, refer to “Re-installing the Device Driver” on page 6.
•
Before starting, check the “System Requirements” section to see if your PC supports YST-MS35D.
•
Make sure that no other CD-ROM is loaded in the CD-ROM drive and that you quit all application programs.
•
Have your Windows 98 CD-ROM ready when you install the Yamaha YST-MS35D speaker device drivers.
You may need it in some cases.
•
The installation procedure may differ from the following instructions depending on the system environment.
Follow the instructions that appear in the dialog box. Please contact your computer’s manufacturer or dealer
if you have any questions.
1. Connect the YST-MS35D speakers as shown in the diagram on page 2 and connect the AC adapter to the
AC receptacle. At this time, do not connect the subwoofer to the computer using the USB cable.
2. Turn on your PC and, if it’s not running already, start Windows 98.
3. Insert the YAMAHA YST-MS35D CD-ROM into the CD-ROM or DVD-ROM drive.
If the Windows 98 Autorun feature is turned on, the installation start up screen appears automatically.
4. Continue with the installation as prompted.
If the Windows 98 Autorun feature is not turned on, you must start the installation manually, as explained below.
5. Double-click the My Computer icon.
The My Computer window opens.
6. Double-click the “Yamaha” CD-ROM icon.
The installation start up screen appears.
7. Continue with the installation as prompted.
8. After the installation is completed, connect the subwoofer to the computer using the USB cable.
4
English
Installing and verifying the YST-MS35D speaker device drivers
Verifying the installation of device drivers
After you have installed the device drivers as explained in the previous section, follow the steps below to verify that
Windows 98 recognizes these drivers.
1. Select “Start,” then select “Settings-->Control Panel” from the menu.
2. Double-click “System” in the control Panel to display the “System Properties” panel, select the “Device
Manager” tab, then select “View devices by type.”
3. Click the plus sign (+) for “Human Interface Devices,” “Sound, video and game controllers,” and “Universal Serial Bus Controller” in the device list, and check to see if “Human Interface Devices,” “YAMAHA
YST-MS35D USB Audio,” and “YAMAHA YST-MS35D USB Composite Device” are listed respectively.
Select “View devices by type”.
“Human Interface Devices” is listed.
Select “View devices by type”.
“YAMAHA YST-MS35D USB Composite Device” is listed.
“YAMAHA YST-MS35D USB Audio” is listed.
• The contents of the list on the display shown above may vary depending on the system environment.
Note: If the letter an exclamation point (!), or a question mark (?) appears to the left of the USB device name,
check the following:
1. Make sure that you have installed the drivers from the included CD-ROM.
2. Check to see if the USB cable is connected securely.
3. The AC adapter plug is connected to the AC receptacle.
If these actions do not resolve the situation, refer to your Windows documentation or ask your computer dealer
to enable the USB port.
5
If you connect the PC and the YST-MS35D via the USB ports using the USB cable before you install the included
application software, the YST-MS35D device driver will not recognize the devices correctly, and will display the
following items in the “System Properties” window:
•
USB Audio Device in the list of “Sound, video and game controllers”
•
USB Composite Device in the list of “Universal serial bus controller”
To recognize the devices correctly, re-install the driver following the steps below:
1. Make sure the YST-MS35D is connected to the PC via the USB cable.
2. Click the “+” symbol next to “Universal serial bus controller” to display the list.
3. Make sure that “USB Composite Device” appears in the list and click to select it.
“USB Composite Device” is listed.
4. Click [Remove].
The dialog shown below appears. Click [OK].
“USB Audio Device” will be deleted.
5. Make sure that “USB Composite Device” has been deleted from the list of “Universal serial bus controller.”
6. Disconnect the USB cable.
7. Insert the included CD-ROM into the CD-ROM drive and re-install the device driver.
8. Check the device driver. Refer to “Verifying the installation of device drivers” on page 5.
6
English
Re-installing the Device Driver
Ensuring the output of audio data from the USB port
Follow the steps below to ensure that the USB port on your computer is ready to output CD audio.
1. Select “Start,” then select “Settings-->Control Panel” from the menu.
2. Double-click “Multimedia” icon in the Control Panel to display the “Multimedia Properties” window, and
under “Playback” in the “Audio” tab, make sure that “YAMAHA YST-MS35D USB Audio” is selected as
the “Preferred device.”
(Depending on the computer, if multiple USB audio devices are connected, the number of devices may appears
in parentheses.)
“YAMAHA YST-MS35D USB Audio” selected as Preferred device
•
The contents of the list on the display shown left
may vary depending on the system environment.
3. Select the “CD Music” tab, make sure that the text below the “CD Music Volume” is Active, and check
“Enable digital CD audio for this CD-ROM device.”
If the text below “CD Music Volume” appears in gray, you cannot check the “Enable digital CD audio for this
CD-ROM device” box. In this case, your CD-ROM drive may not be supported. Consult your computer manufacturer or dealer.
Enable digital CD audio for this CD-ROM device
•
The contents of the list on the display shown left
may vary depending on the system environment.
Now you are ready to enjoy your YST-MS35D Speaker System!
7
You can input analog audio signals into Inputs 1 and 2 (3.5 mm stereo input jacks) on the rear of subwoofer and use
the YST-MS35D system like conventional multimedia speakers. (For example, you can connect the outputs from a
soundcard.)
Some game software programs do not support USB. In this case, instead of using the USB connection, connect Input
1 or 2 on the subwoofer to the audio output jack on your PC using a 3.5mm stereo mini plug cable. Also, specify
your sound card type as the “Preferred device” under “Playback” in the “Audio” tab on the “Multimedia Properties”
panel.
Enjoying your YST-MS35D Speaker System
Adjusting the Volume, Bass, and Treble
First adjust the volume levels, bass, and treble using software controls (such as the Windows 98 Volume Control
panel). After adjustment, use the VOLUME control on the right satellite speaker to set the volume level of the speakers, and use the BASS control on the subwoofer to adjust the low range.
Playing Music CDs
First, make sure that the speaker system is turned on.
1. Select the “Start” button, “Settings,” then “Control Panel.”
2. Double-click the “Multimedia” icon in the “Control Panel.”
3. Select “Multimedia Properties,” then the “Audio” tab.
4. Select “YAMAHA YST-MS35D USB Audio” as the preferred device setting for playback.
5. Select the “CD Music” tab.
6. If multiple CD-ROM drives appear in the “Default CD-ROM drive for playing CD music,” select the CDROM drive that you will use to play music CDs.
7. Adjust the volume level of the music CD.
8. Make sure that the check box for “Enable digital CD audio for this CD-ROM device” is checked.
If Windows 98 disables this box, your CD-ROM drive does not support digital audio. Consult your computer or
CD-ROM drive documentation, or ask your computer dealer for assistance.
9. Follow the instruction on the manual for the corresponding application program to enjoy the speaker
sound.
8
English
Connecting to a non-USB system
Troubleshooting
If the speakers fail to operate normally, check the following table. It lists common operation errors and simple measures that you can take to correct problems. If a problem cannot be corrected, or the symptom is not listed, disconnect the AC adapter and contact your authorized YAMAHA dealer or service center for help.
FAULT
CAUSE
CURE
The speakers are
recognized as an
“unknown device”
by the computer.
The USB cable is not connected securely.
Remove the USB cable from the speaker and computer, then re-connect it securely. Also, turn off and
on the power to the speakers.
You did not complete the Device Driver
Install procedure correctly.
Turn off the power to the speakers, remove the USB
cable, then turn on the power to the speaker again.
If the Device Driver is still not recognized, re-install
it.
No sound comes
from the speakers or subwoofer.
The AC adapter is not properly plugged
into the AC receptacle.
Insert the AC adapter firmly into the AC receptacle.
The
(standby/on) button on the right
satellite speaker is turned off or the AC
adapter is not plugged into the AC receptacle and the DC connector completely.
Plug the AC adapter completely into the AC receptacle and DC connector, then turn on the
(standby/
on) button on the right speaker.
The volume is set to minimum.
Turn the speaker VOLUME control to the right to
increase the volume.
The level of the input signal is too low.
Turn up the volume on the connected device.
Connections are faulty or incomplete.
Make the connections again, firmly, or use a different cable.
You are using a slow-speed USB cable.
Make sure you use the USB cable included in the
package or an equivalent high-speed USB cable.
Windows 98 is not installed on the computer.
Install Windows 98.
The “mute” option is selected in the software volume control in Windows 98.
Cancel “mute” in the software volume control in Window 98.
“YAMAHA YST-MS35D USB Audio” is not Restart the PC. If it does not still work, re-install the
listed under “Sound, video and game con- device driver.
trollers” or “YAMAHA YST-MS35D USB
Composite Device” is not listed under
“Universal serial bus controller” or “Human
Interface Devices” in the Device Manager.
The current CD-ROM drive is not specified Select the drive with which you want to play CDs.
as the “Default CD-ROM drive for playing
CD music” in the “CD Music” tab of the
“Multimedia Properties” panel.
The volume settings in Windows 98 are
not appropriate.
From the [Start] menu, select [Programs]-->[Accessories]-->[Entertainment]-->[Volume Control], and
adjust the volume settings to appropriate levels.
Raise the volume bars shown in the “CD Music Volume” display on the “CD Music” tab in “Multimedia
Properties.”
The bass sound
can not be heard.
The BASS control is set to minimum.
Turn the subwoofer BASS control to the right to
increase the volume.
Sound is distorted.
The level of the input signal is too high.
Turn down the volume on the connected device.
Noise.
Connections are faulty or incomplete.
Make the connections again, firmly, or use a different cable.
Note 1: USB ports are delicate. Handle them with care. Do not insert USB plugs forcefully or you may damage the
port.
Note 2: For more information on issues related to Windows 98, consult the Windows 98 manual or your computer
dealer.
9
You can adjust the speaker angle. Loosen the
screw on the bottom of the speaker stand as
shown in the figure, adjust the angle of the
stand, and tighten the screw to fix the stand.
To prevent the speakers from sliding around,
attach the supplied pads to the four points on the
bottom of each satellite speaker. Place the
speaker on a stable, flat surface.
Loosen
English
Speaker angle and Non skid pad
Tighten
Speaker stand
*
*
* Non skid
pad
Specifications
Type
Output power
Advanced Yamaha Active Servo Technology
Satellite .................................... 6 W + 6 W (1 kHz, 4Ω at T.H.D.=10%)
Subwoofer................................ 18 W (100 Hz, 4Ω at T.H.D.=10%)
Input sensitivity
200 mV (1 kHz, 4Ω at 6 W)
Input impedance
20 kΩ
Frequency response
45 Hz to 20 kHz (Satellite + Subwoofer)
Crossover Frequency
Satellite/Subwoofer 180 Hz
Input Section
Subwoofer................................ 3.5 mm stereo mini jack for audio-signal × 2
USB digital × 1
Output Section
Subwoofer................................ RCA pin jack connected to left satellite speaker
8 pin jack connected to right satellite speaker
Driver
Satellite .................................... 5 cm (2") cone, magnetic shielding
Subwoofer................................ 12 cm (5") cone, magnetic shielding
Power supply
U.S.A. and Canada models...... AC 120 V, 60 Hz
(AC adapter)
Australia model ....................... AC 240 V, 50 Hz
U.K. and Europe models ......... AC 230 V, 50 Hz
Dimensions (W × H × D) Satellite speakers ..................... 65 (2.6") × 75 (3") × 119 (4.7") mm
Subwoofer................................ 183 (7.2") × 196 (7.7") × 183 (7.2") mm
Weight
Satellite speakers ..................... Right: 0.45 kg (1 lb.), Left: 0.36 kg (13 oz.)
Subwoofer................................ 2.3 kg (5 lbs. 1 oz.)
Accessories
AC adapter × 1
3.5 mm stereo mini plug cable × 1 (1.8 m)
USB cable × 1 (2 m)
8 pcs of non skid pads × 1 set, CD-ROM × 1
* Specifications subject to change without notice.
Please contact an authorized Yamaha dealer for more information on this product or connections to your computer.
10
Printed in China
IP
V466000
Download PDF

advertising