Phoenix Audio DRS2 - Mastering Mansion

Phoenix Audio DRS2 - Mastering Mansion
Phoenix Audio DRS2
9/26/09 6:19 PM
Phoenix Audio DRS2 : February 2003
Phoenix Audio DRS2
Microphone Preamp
Published in SOS February 2003
Reviews : Preamp
Print article : Close window
A British company specialising in the maintenance and
refurbishment of vintage Neve equipment have produced a
new preamp design with a classic sound.
Photos: Mark Ewing
Hugh Robjohns
Phoenix Audio International was originally set up to service and maintain classic Neve
studio equipment. Its owner, Shaun Leveque, has not only been supplying the Neve
fraternity, but has also been developing his own equipment, using sophisticated Class-A
circuitry and modern components, updating the sound of the 1960s designs to achieve
modern performance levels. It took two years to refine the unique Class-A topology used
in the Phoenix discrete output stage, called the TF1 module. A discrete stereo DI
interface was next off the drawing board, swiftly followed by a transformerless discrete
Class-A mic input stage.
Combination Design
The DRS2 is a no-frills two-channel mic preamplifier with switchable DI inputs. The electronics use both the transformerless Class-A input stage
and the TF1 output stage. The 1U rackmounting steel case is entirely black, with retro knobs and buttons on the front panel, styled very much on
the classic Neve consoles of thirty or forty years ago. Both channels are equipped identically, starting with a large maroon rotary switch to
control the gain in 5dB steps from 30 to 70dB. Two rectangular white buttons select a 20dB input pad and an earth lift facility — both applying
only to the mic input. A pair of LEDs illuminate at 0dBu (green) and +8dBu (red), but appear to be measuring the unit's output level, rather than
the level after the input stage, as the output level knob affects the indication. The red LED also remains lit for an extended period once triggered,
to ensure that high peaks don't go unnoticed. However, overload really is an unlikely prospect, given the input stage's 24dB of headroom.
Phoenix Audio
DRS2 £1234
pros
Class-A circuitry lends
an attractive sonic
character.
Around 80dB of gain
available.
Excellent build quality.
cons
Owner's manual leaves
something to be
desired.
summary
A dual-channel mic
preamp employing
discrete Class-A circuitry
and output transformers
derived from the classic
console designs of the
1960s. Retro styling,
dedicated DI inputs, and
an unusually large
amount of gain make
this a versatile and
competent unit.
Both mic and DI input sockets are presented on the front panel, the former on an XLR and the latter on a tipsleeve (unbalanced) quarter-inch socket. A mic input XLR is also duplicated on the back, wired in parallel with
the front socket. The DI input bypasses the main mic gain stage, and boosts the input signal with a fixed 20dB
of gain. However, the adjacent output level knob can be used to fine-tune the signal level, providing a
continuously variable control for the selected mic or DI input, with an additional 10dB of gain available when
fully open. Unfortunately, this control has no gain markings, but the operating instructions suggest that the
unity gain point is with the knob set to around the two o'clock position. A definitive panel marking here would
have been useful. Nevertheless, the additional gain is useful for both mic and DI sources, and being able to
introduce a total of 80dB of mic gain will be most welcome to many users who prefer ribbon mics or distant mic
placements.
The block of four illuminated buttons select the DI input instead of the mic input; apply 48V phantom power;
introduce a polarity reversal; and engage a high-pass filter. No figures are provided for the filter turnover
frequency or slope, but I would estimate a 6dB/octave slope turning over at about 125Hz.
The rear panel carries the parallel mic input XLR socket as already mentioned, and two balanced output
sockets for each channel, both at a nominal 0dBu, one on an XLR and a second on a TRS quarter-inch
socket. The maximum output level from the DRS2 is +26dBu, so driving a digital recorder directly should not
be a problem. Equally, the output level can be turned down to avoid overloading the input of a semi-pro
recorder expecting a -10dBV nominal level. The mains power is supplied through a standard IEC socket, with
separate fuse holder and voltage selector switch.
Specs & Build Quality
Whereas the preamp itself creates a good initial impression, the
same cannot be said of the owner's manual which comprises three
sheets of stiff paper stapled together, plus a couple of frequency
response print-outs from a Lindos audio measurement set. The
manual describes very little of the functionality of the unit, bar giving
an idea of how to optimise the gain. While I accept that there is little
to confuse even a novice operator here, a little more information
would be useful — such as the characteristics of the high-pass filter,
the implications of the parallel mic input sockets, and so forth.
Included in this documentation is a detailed set of specifications
http://www.soundonsound.com/sos/Feb03/articles/phoenixdrs2.asp?print=yes
Page 1 of 2
Phoenix Audio DRS2
9/26/09 6:19 PM
which make impressive reading. The frequency response is claimed
The DRS2's standard of internal construction
to lie within ±0.5dB between 20Hz and 20kHz, which the Lindos
and wiring is extremely high.
charts confirmed (with a +0/-1dB tolerance). The frequency extremes appear to tail off gradually, being
only 0.3dB down at 25kHz, for example. The noise floor has similarly impressive specifications, being quoted as below -90dB across the audio
bandwidth.
The internal construction of the DRS2 is exemplary, with very neat wiring looms mimicking the traditional wiring practices of yesteryear — albeit
using cable ties instead of waxed string! A single circuit board occupies a modest area in the centre of the case, and carries most of the
components for both channels in two parallel arrays. The bulk of the input stage and output stage components are all encapsulated in a pair of
plastic boxes, with a few additional components and transistors mounted in between to accommodate the DI input. Each output stage feeds a
line output transformer mounted at the opposite end of the circuit board from a small toroidal mains transformer.
All the controls are mounted directly on the front panel, many also supporting a few passive components. I was pleased to note that the four
buttons in each control section employ LEDs for illumination, rather than incandescent bulbs (green for DI, red for phantom, yellow for the filter
and orange for the polarity reversal).
Listening Tests
The DRS2 is exactly what I expected — a mic preamp from the old school. It has a classic, refined sound character which exudes the same kind
of quality one might associate with vintage Neve designs. Indeed, the slightly rich, full character of this preamp would be perceived by many to
be highly complimentary to a digital recording environment. The high end is extended and clean, while the mid-range seemed a tad warmer or
thicker than my reference GML mic preamps. Overall, the DRS2 also seemed slightly noisier than the GML, but for many this will be easily
outweighed by the additional functionality — the GML offers no filters, pads, fine gain controls, polarity reversals, earth lifts or DI inputs.
Talking of DI inputs, the facility on the Phoenix clearly presents a high input impedance — obviously over 1M(omega) — which suited all the
electric guitar and acoustic pickups that I tried it with. Instrument tonality was perfectly preserved and the gain structure seemed sensibly chosen
and easy to optimise with the output control.
I loved using the DRS2, and not least for its styling, which recalled many happy memories of the vintage Neve and Calrec broadcast consoles I
daily relied upon during my formative broadcast career. There is a huge amount of gain available in this unit, which will appeal to aficionados of
ribbon mics, and a reasonably low and neutral noise floor with an extended bandwidth. If you are seeking a distinctive, high-quality mic preamp
with vintage design values, and either can't find or justify the expense of classic Neve units, you may well find what you are seeking in this
offering from Phoenix Audio.
information
£1233.75 including VAT.
Phoenix Audio +44 (0)1438 360016.
+44 (0)1438 360064.
Click here to email
www.phoenixaudio.net
Published in SOS February 2003
Sound On Sound Ltd is registered in England and Wales. Company number: 3015516. VAT number: GB
638 5307 26.
Registered office: Media House, Trafalgar Way, Bar Hill, Cambridge, CB23 8SQ, United Kingdom.
Email: Contact SOS | Telephone: +44 (0)1954 789888 | Fax: +44 (0)1954 789895
All contents copyright © SOS Publications Group and/or its licensors, 1985-2009. All rights reserved.
The contents of this article are subject to worldwide copyright protection and reproduction in whole or part,
whether mechanical or electronic, is expressly forbidden without the prior written consent of the Publishers. Great
care has been taken to ensure accuracy in the preparation of this article but neither Sound On Sound Limited
nor the publishers can be held responsible for its contents. The views expressed are those of the contributors
and not necessarily those of the publishers.
Web site designed & maintained by PB Associates | SOS | Relative Media
http://www.soundonsound.com/sos/Feb03/articles/phoenixdrs2.asp?print=yes
Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising