scalance x-200 - Industry Support Siemens

scalance x-200 - Industry Support Siemens
___________________
Preface
1
___________________
Functions
SIMATIC NET
Industrial Ethernet Switches
SCALANCE X-200
Operating Instructions
2
___________________
Description of the device
3
___________________
Safety notices
4
___________________
Installation
5
___________________
Connecting up
6
___________________
Approvals
___________________
7
Technical specifications
___________________
A
Dimension drawings
___________________
B
Test of mechanical stability
___________________
C
Training, Service & Support
12/2016
C79000-G8976-C284-09
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C284-09
Ⓟ 12/2016 Subject to change
Copyright © Siemens AG 2012 - 2016.
All rights reserved
Preface
Components of the product
The following parts ship with a SCALANCE X-200 IE switch:
● One device
● One 2-pin plug-in terminal block (signaling contact)
● One 4-pin plug-in terminal block (power supply)
● One DVD (configuration manual, operating instructions, Primary Setup Tool, SNMP OPC
profiles)
The following components are supplied with a SCALANCE X-200 IE switch with the PRO
supplement:
● One device
● Protective caps for the data interfaces
● Protective caps for the connectors of the power supply
● One protective cap for the signaling contact
● One DVD (configuration manual, operating instructions, Primary Setup Tool, SNMP OPC
profiles)
The following parts ship with a SCALANCE XF-200IRT IE switch with slots for bus adapters:
● One device
● One 2-pin plug-in terminal block (signaling contact)
● Two 2-pin plug-in terminal blocks (power supply)
● One DVD (configuration manual, operating instructions, Primary Setup Tool, SNMP OPC
profiles)
● In addition with the premounted variant SCALANCE XF202-2P IRT:
– 2 bus adapters BA SCRJ/RJ-45
● In addition with the premounted variant SCALANCE XF201-3P IRT:
– 1 bus adapter BA 2xSCRJ
– 1 bus adapter BA SCRJ/RJ-45
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
3
Preface
Unpacking, checking
WARNING
Do not use any parts that show evidence of damage. If you use damaged parts, there is no
guarantee that the device will function according to the specification.
If you use damaged parts, this can lead to the following problems:
• Injury to persons
• Loss of the approvals
• Violation of the EMC regulations
Use only undamaged parts.
1. Make sure that the package is complete.
2. Check all the parts for transport damage.
If the consignment is incomplete or damaged, contact your supplier or your local Siemens
office.
Recycling and disposal
The products are low in pollutants, can be recycled and meet the requirements of the WEEE
directive 2012/19/EU for the disposal of electrical and electronic equipment.
Do not dispose of the products at public disposal sites.
For environmentally friendly recycling and the disposal of your old device contact a certified
disposal company for electronic scrap or your Siemens contact (Product return
(https://support.industry.siemens.com/cs/ww/en/view/109479891)).
Note the different national regulations.
Purpose of the Operating Instructions
These operating instructions support you when commissioning networks with the devices of
the product line SCALANCE X-200.
Overview of the technical documentation of the IE Switches X-200
The technical documentation of the X-200 product line is divided into hardware and software
and can be found in the following documents:
● PH SCALANCE X-200 configuration manual
Software description of the X-200 product line
● SCALANCE X-200 BA Operating Instructions
Hardware description for all product groups and general information.
SCALANCE X-200
4
Operating Instructions, 12/2016, C79000-G8976-C284-09
Preface
You will find the documents here:
● On the data medium that ships with some products:
– Product CD / product DVD
– SIMATIC NET Manual Collection
● On the Internet pages of Siemens Industry Online Support
(http://support.automation.siemens.com/WW/view/en/33118791/133300).
Validity of the Operating Instructions
These operating instructions are valid for the following devices:
SCALANCE X-200 and SCALANCE XF-200
Product name:
Article number:
X204-2
6GK5 204-2BB10-2AA3
X204-2TS
6GK5 204-2BB10-2CA2
X204-2FM
6GK5 204-2BB11-2AA3
X204-2LD
6GK5 204-2BC10-2AA3
X204-2LD TS
6GK5 204-2BC10-2CA2
X206-1
6GK5 206-1BB10-2AA3
X206-1LD
6GK5 206-1BC10-2AA3
X208
6GK5 208-0BA10-2AA3
X208PRO
6GK5 208-0HA10-2AA6
X212-2
6GK5 212-2BB00-2AA3
X212-2LD
6GK5 212-2BC00-2AA3
X216
6GK5 216-0BA00-2AA3
X224
6GK5 224-0BA00-2AA3
Flat design:
XF204
6GK5 204-0BA00-2AF2
XF204-2
6GK5 204-2BC00-2AF2
XF206-1
6GK5 206-1BC00-2AF2
XF208
6GK5 208-0BA00-2AF2
SCALANCE X-200IRT and XF-200IRT
Product name:
Article number:
X200-4P IRT
6GK5 200-4AH00-2BA3
X201-3P IRT
6GK5 201-3BH00-2BA3
X201-3P IRT PRO
6GK5 201-3JR00-2BA6
X202-2IRT
6GK5 202-2BB00-2BA3
X202-2P IRT
6GK5 202-2BH00-2BA3
X202-2P IRT PRO
6GK5 202-2JR00-2BA6
X204IRT
6GK5 204-0BA00-2BA3
X204IRT PRO
6GK5 204-0JA00-2BA6
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
5
Preface
SCALANCE X-200IRT and XF-200IRT
Flat design:
XF204IRT
6GK5 204-0BA00-2BF2
XF204-2BA IRT *)
6GK5 204-2AA00-2BD2
*) Basic device without bus adapter
Premounted variants
Product name:
Article number:
Components:
Article number components:
XF201-3P IRT
6GK5 201-3BH00-2BD2
1 basic device XF204-2BA 6GK5 204-2AA00-2BD2
IRT
1 bus adapter BA 2xSCRJ 6ES7 193-6AP00-0AA0
1 bus adapter BA
SCRJ/RJ-45
XF202-2P IRT
6GK5 202-2BH00-2BD2
6ES7 193-6AP20-0AA0
1 basic device XF204-2BA 6GK5 204-2AA00-2BD2
IRT
2 bus adapters BA
SCRJ/RJ-45
6ES7 193-6AP20-0AA0
Purpose
The SCALANCE X-200 devices are switches for setting up Ethernet networks for industrial
applications.
Restricted area of application according to Hazardous Locations (HazLoc)
The devices are only suitable for use in the following areas:
● In areas according to Class I, Division 2, Groups A, B, C and D and in areas without
explosive atmospheres.
● In areas according to Class I, Zone 2 Groups IIC and in areas without explosive
atmospheres.
Names of the devices in these operating instructions
Unless mentioned otherwise, the descriptions in these operating instructions refer to all
devices of the SCALANCE X-200 product line named above in the section on Validity.
In the remainder of the instructions, these will also be referred to as IE switches or also
simply as X-200.
Further documentation
System manuals for SIMATIC NET products
In the system manuals "Industrial Ethernet / PROFINET Industrial Ethernet" and "Industrial
Ethernet / PROFINET passive network components", you will find information on other
SIMATIC NET products that you can operate along with the devices of this product line in an
Industrial Ethernet network.
SCALANCE X-200
6
Operating Instructions, 12/2016, C79000-G8976-C284-09
Preface
You will find the system manuals on the Internet pages of Siemens Industry Online Support
under the following entry IDs:
● Industrial Ethernet / PROFINET Industrial Ethernet System Manual
27069465 (http://support.automation.siemens.com/WW/view/en/27069465)
● Industrial Ethernet / PROFINET - Passive Network Components System Manual
84922825 (http://support.automation.siemens.com/WW/view/en/84922825)
Manual Collection "Distributed I/O System ET 200SP"
In the reference manual for the scalable IO system ET 200SP you will find more information
on the bus adapters.
You will find the reference manual on the Internet pages of Siemens Industry Online
Support:
● SIMATIC ET 200SP Manual Collection
(https://support.industry.siemens.com/cs/ww/en/ps/man)
Finding information
To help orientation, there is not only a table of contents but also an Index in the Appendix.
The SIMATIC NET Glossary also provides additional help, see below.
Audience
These operating instructions are intended for persons involved in commissioning networks in
which IE switches are used.
SIMATIC NET Selection Tool
The SIMATIC NET selection tool supports you when selecting Industrial Ethernet switches
and components for Industrial Wireless Communication. You will find current information on
the Product Support pages under the following entry ID:
39134641 (http://support.automation.siemens.com/WW/view/en/39134641)
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
7
Preface
Where to find Siemens documentation
● Article numbers
You will find the article numbers for the Siemens products of relevance here in the
following catalogs:
– SIMATIC NET - Industrial Communication / Industrial Identification, catalog IK PI
– SIMATIC - Products for Totally Integrated Automation and Micro Automation, catalog
ST 70
You can request the catalogs and additional information from your Siemens
representative. You will also find the product information in the Siemens Industry Mall at
the following address:
(https://mall.industry.siemens.com)
● Manuals on the Internet
You will find SIMATIC NET manuals on the Internet pages of Siemens Industry Online
Support:
10805878 (http://support.automation.siemens.com/WW/view/en/10805878)
Go to the required product in the product tree and make the following settings:
Entry type “Manuals”
● Manuals on the data medium
You will find manuals of SIMATIC NET products on the data medium that ships with many
of the SIMATIC NET products.
See also
Link to Customer Support (http://support.automation.siemens.com/WW/view/en)
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines
and networks. Systems, machines and components should only be connected to the
enterprise network or the internet if and to the extent necessary and with appropriate security
measures (e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit
http://www.siemens.com/industrialsecurity (http://www.siemens.com/industrialsecurity)
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends to apply product updates as soon as available and to
always use the latest product versions. Use of product versions that are no longer supported,
and failure to apply latest updates may increase customer’s exposure to cyber threats.
SCALANCE X-200
8
Operating Instructions, 12/2016, C79000-G8976-C284-09
Preface
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://support.industry.siemens.com/cs/ww/en/ps/15247/pm
(https://support.industry.siemens.com/cs/ww/en/ps/15247/pm).
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary here:
● SIMATIC NET Manual Collection or product DVD
The DVD ships with certain SIMATIC NET products.
● On the Internet under the following address:
50305045 (http://support.automation.siemens.com/WW/view/en/50305045)
Trademarks
The following and possibly other names not identified by the registered trademark sign ® are
registered trademarks of Siemens AG:
SIMATIC NET, SCALANCE, C-PLUG, OLM
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
9
Preface
SCALANCE X-200
10
Operating Instructions, 12/2016, C79000-G8976-C284-09
Table of contents
Preface ................................................................................................................................................... 3
1
Functions .............................................................................................................................................. 13
2
Description of the device ....................................................................................................................... 17
3
4
5
2.1
Device views ...........................................................................................................................17
2.2
Accessories .............................................................................................................................20
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.3.7
2.3.8
The LEDs ................................................................................................................................23
LED display when the device starts up ...................................................................................23
Power LED "L" (green/yellow LED) ........................................................................................23
Fault LED "F" (yellow/red LED) ..............................................................................................24
Redundancy manager LED "RM" (green LED).......................................................................24
Standby LED "RM" (yellow LED) ............................................................................................25
Port LEDs "P" (green/yellow LEDs) ........................................................................................26
Diagnostics LEDs for optical connectors "F" (yellow LED) .....................................................26
Show Location ........................................................................................................................27
2.4
The SET button .......................................................................................................................28
2.5
The C-PLUG ...........................................................................................................................29
Safety notices ....................................................................................................................................... 33
3.1
Safety notices in general ........................................................................................................33
3.2
Safety notices for hazardous areas ........................................................................................34
3.3
Security recommendations .....................................................................................................35
Installation ............................................................................................................................................ 39
4.1
Safety notices for installation ..................................................................................................39
4.2
Installation options ..................................................................................................................42
4.3
Installation on a DIN rail ..........................................................................................................43
4.4
Installation on a standard rail ..................................................................................................44
4.5
Wall mounting .........................................................................................................................45
4.6
Mounting bus adapters ...........................................................................................................46
Connecting up....................................................................................................................................... 47
5.1
Safety when connecting up .....................................................................................................47
5.2
Wiring rules .............................................................................................................................50
5.3
5.3.1
5.3.2
5.3.3
5.3.4
Power supply ..........................................................................................................................51
Supply with X-200 via the terminal block ................................................................................51
Supply for X208PRO...............................................................................................................52
Supply for IRT-PRO devices ...................................................................................................52
Supply with XF-200IRT devices with bus adapter slots ..........................................................55
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
11
Table of contents
5.4
Grounding .............................................................................................................................. 56
5.5
Signaling contact .................................................................................................................... 57
5.6
5.6.1
5.6.1.1
5.6.1.2
5.6.2
5.6.2.1
5.6.2.2
5.6.2.3
5.6.3
Attachment to Industrial Ethernet........................................................................................... 59
Electrical connections ............................................................................................................ 59
Electrical attachments to Industrial Ethernet ......................................................................... 59
Electrical connectors of the X208PRO .................................................................................. 61
Optical attachments to Industrial Ethernet ............................................................................. 62
Multimode fiber-optic cable .................................................................................................... 63
Single mode fiber-optic cable................................................................................................. 64
POF and PCF cables ............................................................................................................. 64
Push-pull connector for IRT-PRO devices ............................................................................. 66
6
Approvals ............................................................................................................................................. 67
7
Technical specifications ........................................................................................................................ 75
A
Dimension drawings .............................................................................................................................. 87
B
Test of mechanical stability ................................................................................................................... 93
C
Training, Service & Support .................................................................................................................. 95
Index .................................................................................................................................................... 97
SCALANCE X-200
12
Operating Instructions, 12/2016, C79000-G8976-C284-09
1
Functions
Functions of the X-200 IE Switches
The X-200 IE switches are ideally suited for setting up Industrial Ethernet networks in bus,
star and ring structures with transmission rates of 10/100 Mbps. All X-200 switches operate
in the SIMATIC environment.
Hardware properties:
● X devices have a rugged metal housing and can be installed on a DIN rail, a standard rail
or directly on a wall.
● XF devices have a plastic housing and a flat design. They are suitable for installation on a
DIN rail.
● Redundant power supply, 2 x 24 VDC (exception: IRT-PRO devices)
● Diagnostics LED
● Signaling contact
● SET button for local configuration of the signaling contact
● Slot for C-PLUG
● Reliable plug-in connections thanks to rugged device connectors suitable for industry in
conjunction with PROFINET-compliant FastConnect plugs.
● TS devices meet the railway standard EN 50155
Software properties:
● PROFINET Diagnostics
● Topology support (LLDP)
● CLI - Command Line Interface / Telnet
● WBM - Web Based Management
● Configuration with STEP 7
● SNMP
● Ring redundancy including redundancy manager
● Passive Listening
● FM devices support the Fiber Monitoring Protocol and allow the monitoring of optical line
sections.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
13
Functions
Special features of the X-200IRT IE switches
The IRT variants were designed specifically for setting up Industrial Ethernet networks with
isochronous/clock synchronous real-time communication. In addition to the properties named
above, the IRT switches also provide the following functions:
● IRT communication based on the combination of the switching methods cut through and
store and forward.
● Fast media redundancy thanks to an integrated redundancy manager for Fast Ethernet.
● Standby redundancy
Special features of the PRO variants
The devices with the "PRO" supplement are designed with degree of protection IP65 or IP67
for use outside a cabinet.
Frame delay times
The number of IE Switches X-200 connected in a line influences the frame delay.
Note
Frame delay time with X-200 without IRT
When a frame passes through X-200 IE switches, it is delayed by the Store&Forward
function of the X-200 IE switches.
• With a 64 byte frame length by approx. 10 microseconds (at 100 Mbps).
• With a 1500 byte frame length by approx. 130 microseconds (at 100 Mbps).
This means that the more IE Switch X-200 devices the frame passes through, the longer the
frame delay.
Note
Frame delay time with X-200 with IRT
The more X-200IRT IE switches a frame runs through, the higher the frame delay. By using
the "cut through" switching mechanism, the X-200IRT IE switches are ideal to meet the realtime requirements of PROFINET.
Cut through is, however, not possible:
• Between a port set to 10 Mbps and a port set to 100 Mbps.
• When two packets are to be sent at the same time on one port.
In this case, an X-200 IE switch changes to Store&Forward and the delay increases.
SCALANCE X-200
14
Operating Instructions, 12/2016, C79000-G8976-C284-09
Functions
Overview of the functions
The following table shows the hardware and software properties for each product variant of
the X-200 switches in detail:
Number of electrical and optical connectors in the product name
The number before the hyphen in the product name indicates the number of electrical
connectors. The number following the hyphen indicates the number of optical connectors of
the device. For example, the switch X212-2 has twelve electrical and two optical connectors.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
15
Functions
SCALANCE X-200
16
Operating Instructions, 12/2016, C79000-G8976-C284-09
2
Description of the device
2.1
Device views
Device view based on the example of an X204-2TS
The following figure describes the individual components of an IE switch X200.
1 LEDs for attachments to Industrial Ethernet
2 LEDs
• L: Power LED, power supply
• F: Fault LED
• RM: Redundancy manager or standby
3 Connector for signaling contact
4 Connector for power supply
5 SET button
6 Optical attachment to Industrial Ethernet
7 Electrical attachment to Industrial Ethernet
8 (on rear of device, not shown in figure:) Slot for CPLUG
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
17
Description of the device
2.1 Device views
Device view based on the example of an X202-2P IRT PRO
The following figure describes the individual components of a PRO version of an IE switch X200.
1
Electrical attachments to Industrial Ethernet
2
LEDs for electrical connectors
3
LEDs for optical connectors with diagnostics
LEDs
4
LEDs
• L: Power LED, power supply
• F: Fault LED
• RM:
– green = redundancy manager
– yellow = standby indicator
5
Optical attachments to Industrial Ethernet
6
Connector for the power supply (supplied with
L1, additionally looped through to L2)
7
Connector for signaling contact
8
Power supply for further devices (looped
through from L1 to L2)
9
(on rear of device, not shown in figure): Slot for
the C-PLUG and SET button
Device view based on the example of an XF204
The following figure describes the individual components of an IE switch X-200, flat design.
1
LEDs
• L: Power LED, power supply
• F: Fault LED
• RM: Redundancy manager
2
Attachments to Industrial Ethernet
3
Connector for power supply
4
Connector for signaling contact
5
(behind the connectors, not shown in figure:)
SET button
6
(on side of device, not shown in figure:) Slot for
C-PLUG
7
LEDs for attachments to Industrial Ethernet
SCALANCE X-200
18
Operating Instructions, 12/2016, C79000-G8976-C284-09
Description of the device
2.1 Device views
Device view based on the example of an XF204-2BA IRT
The following figure describes the individual components of an IE switch XF-200IRT, flat
design.
1
BaseUnit with slots for 2 bus adapters
The BaseUnit provides the electrical and
mechanical connection of the bus adapters.
2
LEDs
• L: Power LED, power supply
• F: Fault LED
• RM: Redundancy manager
3
Slot for C-PLUG
4
SET button
5
Connector for signaling contact
6
Connector for power supply
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
19
Description of the device
2.2 Accessories
2.2
Accessories
C-PLUG
Component
Description
Article number
C-PLUG
Configuratiioon plug, exchangeable storage medium for configuration data
6GK1 900-0AB00
Component
Description
Article number
Redundancy module
SITOP PSE202U
NEC Class 2
Extension module for limiting the output power
according to NEC Class 2 (power limiter)
6EP1 962-2BA00
Component
Description
Article number
Power Plug PRO
5-pin push-pull-connector for installation on site
1 connector per package
6GK1 907-0AB10-6AA0
Component
Description
Article number
IE FC RJ-45 PLUG
PRO (push pull)
RJ-45 data plug-in connector for IE FC TP cables
2x2, IP65
1 connector per package
6GK1 901-1BB20-6AA0
IE RJ-45 PLUG PRO
(push pull)
RJ-45 data plug-in connector for IE TP cables
2x2, IP65
1 connector per package
6GK1 901-1BB10-6AA0
IE FC RJ-45 PLUG
180 2x2
RJ-45 data plug-in connector for IE FC cables
6GK1 901-1BB10-2AA0
2x2, 180° cable outlet 10/100 Mbps, rugged metal
housing, 1 connector per package
IE FC RJ-45 PLUG
180 2x2
RJ-45 data plug-in connector for IE FC cables
2x2, 180° cable outlet, 10/100 Mbps, rugged
metal housing
Power llimiter
Plug Power Plug PRO
RJ-45 data plug-in connector
6GK1 901-1BB10-2AB0
10 connectors per package
IE FC RJ-45 PLUG
180 2x2
RJ-45 data plug-in connector for IE FC cables
2x2, 180° cable outlet, 10/100 Mbps, rugged
metal housing
6GK1 901-1BB10-2AE0
50 connectors per package
IE FC RJ-45 PLUG
180 4x2
RJ-45 data plug-in connector for IE FC cables
4x2 (24 AWG), 180° cable outlet, CAT6A,
10/100/1000/10000 Mbps, rugged metal housing
6GK1 901-1BB12-2AA0
1 connector per package
SCALANCE X-200
20
Operating Instructions, 12/2016, C79000-G8976-C284-09
Description of the device
2.2 Accessories
Component
Description
Article number
IE FC RJ-45 PLUG
180 4x2
RJ-45 data plug-in connector for IE FC cables
4x2 (24 AWG), 180° cable outlet, CAT6A,
10/100/1000/10000 Mbps, rugged metal housing
6GK1 901-1BB12-2AB0
10 connectors per package
IE FC RJ-45 PLUG
180 4x2
RJ-45 data plug-in connector for IE FC cables
4x2 (24 AWG), 180° cable outlet, CAT6A,
10/100/1000/10000 Mbps, rugged metal housing
6GK1 901-1BB12-2AE0
50 connectors per package
SC RJ plug-in connector
Component
Description
Article number
IE SC RJ POF PLUG
PRO (push pull)
SC RJ plug-in connector for POF fiber-optic cables
1 duplex connector per package
6GK1 900-0MB00-6AA0
IE SC RJ PCF PLUG
PRO (push pull)
SC RJ plug-in connector for PCF fiber-optic cables
6GK1 900-0NB00-6AA0
1 duplex connector per package
Bus adapter
The bus adapters allow you a free choice of the connector technology for SCALANCE
XF204-2BA IRT.
SCALANCE XF204-2BA IRTs support the following bus adapters:
Component
Description
BA 2×RJ45
PROFINET bus adapter with Ethernet socket for
standard RJ-45 plugs
6ES7 193-6AR00-0AA0
BA 2×RJ45 (Coated)
PROFINET bus adapter with Ethernet socket for
standard RJ-45 plugs, with printed circuit boards
with conformal coating.
6AG1 193-6AR00-7AA0
BA 2×FC
PROFINET bus adapter with FastConnect Ethernet connector for direct connection of the bus
cable)
6ES7 193-6AF00-0AA0
BA 2×FC (Coated)
PROFINET bus adapter with FastConnect Ethernet connector for direct connection of the bus
cable with printed circuit boards with conformal
coating.
6AG1 193-6AF00-7AA0
BA 2xSCRJ
PROFINET bus adapter with fiber-optic connector 6ES7 193-6AP00-0AA0
POF/PCF
BA 2xSCRJ (Coated) PROFINET bus adapter with FO connector
POF/PCF with printed circuit boards with conformal coating.
Article number
6AG1 193-6AP00-2AA0
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
21
Description of the device
2.2 Accessories
Component
Description
BA SCRJ/RJ45
Media converter, PROFINET bus adapter with
fiber-optic connector POF/PCF ↔standard RJ-45
plug
6ES7 193-6AP20-0AA0
Article number
BA SCRJ/FC
Media converter (PROFINET bus adapter with
fiber-optic connector POF/PCFv↔ direct connection of the bus cable
6ES7 193-6AP40-0AA0
Note
To operate a SCALANCE XF204-2BA IRT you always need to plug in two bus adapters. If
only one bus adapter is plugged in communication is blocked via all ports of the SCALANCE
XF204-2BA IRT.
Accessories for devices with bus adapter slots
Component
Description
Article number
Reference identification
labels
The reference identification plates (according to EN 81346) can be plugged
into every bus adapter, see Manual
Collection "Distributed IO system ET
200SP2", reference in the section
"Preface (Page 3)" section "Further
documentation".
6ES7 193-6LF30-0AW0
Figure
The plates allow reference identification
of the ET 200SP components.
They can be ordered on a mat for
thermotransfer and ink jet printers.
Due to the standard plotter frame, the
reference identification plate is suitable
for labeling with ECAD systems.
Mat with 16 plates
pack of 10
Cover for the bus adapter
slots
Cover for the unused bus adapter slots
6ES7 591-3AA00-0AA0
-
With the cover the plug contacts are
protected from contamination.
pack of 5
SCALANCE X-200
22
Operating Instructions, 12/2016, C79000-G8976-C284-09
Description of the device
2.3 The LEDs
2.3
The LEDs
2.3.1
LED display when the device starts up
When the X-200 starts up, the LEDs light up in the following sequence:
● The green power LED lights up immediately after turning on the device.
● The LEDs of the Ethernet connectors light up for approximately 6 seconds.
● When the Ethernet LEDs go off, the red fault LED is lit for approximately 20 seconds.
● Following this, after approximately 2 seconds the correct link status is displayed.
The X-200 is now ready for operation.
2.3.2
Power LED "L" (green/yellow LED)
The power LED shows the status of the power supply on the X-200 IE switch. The power
LED can light up either green or yellow. The meanings of the display are as follows:
LED color
LED status
Meaning
Green
Lit
Both power supplies are connected; in other words, redundant power supply.
Yellow
Lit
Only one power supply is connected or the voltage is < 14 VDC at one of the two
connectors.
-
Off
No power supply is connected or the voltage is < 14 VDC or with TS devices < 8
VDC.
Note
The following devices do not have a redundant power supply:
• X201-3P IRT PRO
• X202-2P IRT PRO
• X204IRT PRO
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
23
Description of the device
2.3 The LEDs
2.3.3
Fault LED "F" (yellow/red LED)
The fault LED indicates a fault/error on the X-200. If the X-200 detects an error, the signaling
contact is opened at the same time assuming that the response of the signaling contact was
not configured differently.
The meanings of the fault LED display are as follows:
LED color
LED status
Yellow
Lit
Meaning
The LED can only adopt this status with FM devices.
Check the received power or the loss of power on optical connections. If necessary,
replace the parts.
Red
Lit
The fault LED lighting up can have the following meanings:
•
Link down event on a monitored port
•
Loss of the power supply
•
C-PLUG error
•
Device is in PROFINET mode:
–
There is no connection to the controller.
–
There is a connection to the controller. A configured diagnostics interrupt is
also pending, for example power fail interrupt, C-PLUG interrupt etc.
•
Redundancy manager connected through
•
Switchover of standby connection
•
A defined value was undershot in a monitored optical connection.
•
A loop was detected.
•
Device startup. The LED lights up for approximately 20 seconds.
Red
Flashing
Internal error detected. Notify maintenance personnel. If necessary, send the device
in for repair.
-
Off
No error detected.
2.3.4
Redundancy manager LED "RM" (green LED)
The green LED shows the following statuses of the X-200:
LED color
LED status
Meaning
Green
Lit
The device is operating in the role of redundancy manager. The ring is operating free
of errors. The monitoring is enabled.
Green
Flashing
The device is operating in the role of redundancy manager. An interruption was detected in the ring. The device has switched through.
-
Off
The device is not operating in the role of redundancy manager.
SCALANCE X-200
24
Operating Instructions, 12/2016, C79000-G8976-C284-09
Description of the device
2.3 The LEDs
Note
This LED labeled on the device with "RM" has a dual function. The color of the display
changes depending on the function:
• If the LED is lit green, the redundancy manager function is indicated.
• If the LED is lit yellow, the standby function is indicated.
In Web Based Management (WBM), the LED is labeled differently depending on the
function:
• The redundancy manager function (as shipped) is labeled "RM".
• The standby function is labeled "SB" in the WBM.
2.3.5
Standby LED "RM" (yellow LED)
You will find the standby LED only on devices with the IRT function.
Note
This LED labeled on the device with "RM" has a dual function. The color of the display
changes depending on the function:
• If the LED is lit green, the redundancy manager function is indicated.
• If the LED is lit yellow, the standby function is indicated.
In Web Based Management (WBM), the LED is labeled differently depending on the
function:
• The redundancy manager function (as shipped) is labeled "RM".
• The standby function is labeled "SB" in the WBM.
The yellow LED indicates the following statuses of the X-200IRT:
LED color
LED status
Meaning
Yellow
Lit
The standby function is activated, the switch is in active mode.
Yellow
Flashes slowly
The standby function is activated, the switch is in passive mode.
Yellow
Flashes quickly
Standby partner lost.
-
Off
The standby function is not activated.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
25
Description of the device
2.3 The LEDs
2.3.6
Port LEDs "P" (green/yellow LEDs)
The LEDs of the Ethernet connectors can be lit green or yellow. The meanings of the display
are as follows:
LED color
LED status
Meaning
Green
Lit
Link exists, no data reception
Yellow
Lit
Link exists, data being received
Device startup. The LED lights up for approximately 6 seconds.
Yellow
Flashing
Setting or display of the fault mask
The following statuses of the port LEDs do not exist on devices with the IRT function:
LED color
LED status
Meaning
Green
flashes
once per period
Link exists and port in "blocking" status.
In this status, the port only receives management data (no user data).
Green
flashes
three times per
period
Link exists and port is deactivated by the management.
In this status, no data is sent or received via the port.
Green
flashes
four times per
period
Port exists and is in the "monitor port" status.
In this status, the data traffic of another port is mirrored to this port.
2.3.7
Diagnostics LEDs for optical connectors "F" (yellow LED)
You will find the diagnostics LEDs only on the devices with the IRT function. With the
SCALANCE XF204-2BA IRT you will only find the diagnostics LEDs on bus adapters with
SCRJ ports.
The status of the optical connectors is indicated by an additional yellow LED per connector.
The LEDs signal the following statuses:
LED color
LED status
Meaning
Yellow
Lit
Check the plug-in connection and the quality of the fiber-optic cable. If necessary,
replace the parts.
-
Off
Relevant only if the link exists. The existing link power margin is adequate for errorfree operation.
SCALANCE X-200
26
Operating Instructions, 12/2016, C79000-G8976-C284-09
Description of the device
2.3 The LEDs
2.3.8
Show Location
Localizing an IE Switches X-200
To identify an IE Switch X-200 locally and with certainty, you can use the "show location"
function on a programming device to select the node over the network and make it flash.
This can be used, for example, when assigning addresses to make sure that the correct
node receives the address. All port LEDs of the addressed node flash green at 2 Hz.
With the Primary Setup Tool (PST) V3.0 or higher, you can trigger this function with "Module
\ Flash".
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
27
Description of the device
2.4 The SET button
2.4
The SET button
Function of the SET button
With the SET button, you can change various settings of the device. The changed settings
remain after cycling power to the device.
Different settings are made depending on how long you hold down the SET button, as
described in the following table:
Figure 2-1
Phase
1
Phases for changing settings using the SET button
Description
The currently set fault mask is displayed. If no fault mask has been set, all ports flash one
after the other.
If you release the button in phase 1, this has no effect.
2
The LEDs of the ports at which there is currently a link flash at 2.5 Hz.
If you release the button in phase 2, this has no effect.
3
The LEDs of the ports at which there is currently a link and the LEDs of the connected
power supply are lit permanently.
If you release the button in phase 3, the fault mask corresponding to the lit LEDs is adopted.
4
The RM LED flashes.
If you release the button in phase 4, the redundancy manager is deactivated. The redundancy function remains enabled. The device changes to "Automatic Redundancy Detect"
mode.
5
The RM LED is lit permanently.
If you release the button in phase 5, the redundancy function is activated and the device is
configured as HRP manager.
6
All LEDs flash.
The device is reset to the factory defaults.
SCALANCE X-200
28
Operating Instructions, 12/2016, C79000-G8976-C284-09
Description of the device
2.5 The C-PLUG
2.5
The C-PLUG
Area of application
The C-PLUG is an exchangeable medium for storage of the configuration and project
engineering data of the basic device. This means that the configuration data remains
available if the basic device is replaced.
How it works
Power is supplied by the basic device. The C-PLUG retains all data permanently when the
power is turned off.
If an empty C-PLUG (factory settings) is inserted, all configuration data of an IE
Switch X-200 is saved to it when the device starts up. Changes to the configuration during
operation are also saved on the C-PLUG without any operator intervention being necessary.
If a C-PLUG is inserted, the configuration stored internally on the basic device is no longer
changed. Al changes made to the configuration during ongoing operation are only stored on
the C-PLUG.
A basic device with an inserted C-PLUG automatically uses the configuration data of the
C-PLUG when it starts up. This is, however, only possible when the data was written by a
compatible device type.
This allows fast and simple replacement of the basic device. If a device is replaced, the CPLUG is taken from the failed component and inserted in the replacement device. The first
time it is started up, the replacement device has the same configuration as the failed device
except for the MAC address set by the vendor.
Compatible devices
As a general rule, the data on the C-PLUG is only compatible with devices having an
identical order number and the same device name.
The device combinations shown in the following table are exceptions. With these devices,
the exchange of the C-PLUG is possible in one direction.
Device type
C-PLUG created by device with
order number
Compatible with device with
order number
X204-2
6GK5 204-2BB00-2AA3
6GK5 204-2BB10-2AA3
X204-2LD
6GK5 204-2BC00-2AA3
6GK5 204-2BC10-2AA3
X206-1
6GK5 206-1BB00-2AA3
6GK5 206-1BB10-2AA3
X206-1LD
6GK5 206-1BC00-2AA3
6GK5 206-1BC10-2AA3
X208
6GK5 208-0BA00-2AA3
6GK5 208-0BA10-2AA3
X208PRO
6GK5 208-0HA00-2AA6
6GK5 208-0HA10-2AA6
Note
Combinations other than those shown in the table are not compatible with each other.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
29
Description of the device
2.5 The C-PLUG
Note
If you insert a C-PLUG in a compatible device, the system name of the original device is
entered both in the system name as well as in the PROFINET IO device name of the
compatible device.
Using a previously written C-PLUG
If you want to insert a C-PLUG that has already been used and written to into a new
differently configured X-200 IE switch, you will first need to delete the existing data on the CPLUG. You will find information about this in the configuration manual of the SCALANCE X200 in the section on the WBM menu items.
Note
The X-200 IE switches normally start up with the configuration of the C-PLUG, assuming this
was written to by a compatible device type. If the C-PLUG was written to by an incompatible
device type, the basic device will not start up fully and signals an error. The WBM menu
"System C-PLUG" is displayed automatically. Here, use the "Modify C-PLUG" function to
specify whether or not the device operates with a C-PLUG.
If you operate a device with a C-PLUG, the C-PLUG can either be initialized with the factory
settings or with the settings stored internally on the device.
Diagnostics
The following events are signaled by the diagnostics mechanisms of the X-200, such as
LEDs, WBM etc.:
● Inserting a C-PLUG that contains the configuration of an incompatible device type.
● The accidental removal of a C-PLUG
● General malfunctions of the C-PLUG.
The C-PLUG does not ship with the product
The C-PLUG is not supplied with the IE switches X-200, see section “Accessories
(Page 20)“.
Inserting in the slot
NOTICE
• Insert and remove the C-PLUG only when power is off.
• In a device with a varnished printed circuit board, you may only use a C-PLUG with a
varnished board.
SCALANCE X-200
30
Operating Instructions, 12/2016, C79000-G8976-C284-09
Description of the device
2.5 The C-PLUG
Figure 2-2
C-PLUG and slot based on the example of an X-200
You will find the slot for the various product groups in the "Device views (Page 17)"
Follow the steps below to insert the C-PLUG:
1. Remove the screw cover.
2. Insert the C-PLUG in the slot.
3. Close the slot with the screw cover.
Removing the C-PLUG
It is only necessary to remove the C-PLUG if the IE Switch X-200 develops a fault.
You can lever the C-PLUG out of the slot carefully using flat pliers, tweezers, or a small
screwdriver.
If no C-PLUG is inserted in the device, when the device restarts, an error message is output
in Web Based Management and in the Command Line Interface. In this case, you will need
to set the device to operation without C-PLUG. For further information, refer to the section
"System C-PLUG" in the section on the WBM menu in the configuration manual.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
31
Safety notices
3.1
3
Safety notices in general
Note the following safety notices. These relate to the entire working life of the device.
WARNING
Do not use any parts that show evidence of damage
If you use damaged parts, there is no guarantee that the device will function according to
the specification.
If you use damaged parts, this can lead to the following problems:
• Injury to persons
• Loss of the approvals
• Violation of the EMC regulations
• Damage to the device and other components
Use only undamaged parts.
Installation guidelines
The product meets the requirements if you adhere to the installation and safety notices
contained in this documentation and in the following documentation when installing and
operating the product.
Current documentation on the Internet
The current descriptions of the currently available products can be found on the Product
Support pages under the entry IDs below:
● Configuration manual SIMATIC NET PH SCALANCE X-200
63203259 (http://support.automation.siemens.com/WW/view/en/63203259)
● System manual SIMATIC NET Industrial Ethernet Network Manual
27069465 (http://support.automation.siemens.com/WW/view/en/27069465)
● Configuration manual EMC Installation Guidelines
60612658 (http://support.automation.siemens.com/WW/view/en/60612658)
Special safety notices
You should also read the safety notices relating to handling in the individual sections,
particularly in the sections "Installation" and "Connecting up".
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
33
Safety notices
3.2 Safety notices for hazardous areas
Electrostatic discharge
NOTICE
Electrostatic sensitive devices (ESD)
Electronic modules contain electrostatic sensitive components
These components can easily be destroyed if handled incorrectly.
Note the following instructions to avoid damage.
• Touch electronic modules only when you absolutely need to work on them.
• If electronic modules need to be touched, the body of the person involved must first be
electrostatically discharged and grounded.
• Do not bring electronic modules in contact with electrically isolating materials such as
plastic film, isolating table top pads or clothing made of synthetic fibers.
• Place the modules only on conductive surfaces.
• Pack, store and transport electronic modules and components only in conductive
packaging such as metalized plastic or metal containers, conductive foam or household
aluminum foil.
3.2
Safety notices for hazardous areas
Safety notices on use in hazardous areas
General safety notices relating to protection against explosion
WARNING
EXPLOSION HAZARD
Do not open the device when the supply voltage is turned on.
Safety notices when using the device according to Hazardous Locations (HazLoc) and FM.
If you use the device under HazLoc or FM conditions you must also keep to the following
safety notices in addition to the general safety notices for protection against explosion:
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or nonhazardous locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations
only.
SCALANCE X-200
34
Operating Instructions, 12/2016, C79000-G8976-C284-09
Safety notices
3.3 Security recommendations
3.3
Security recommendations
NOTICE
Information security
Connect to the device and change the standard passwords for the users "admin" and "user"
before you operate the device. To be able to change passwords you need to be logged in
with write access to the configuration data.
To prevent unauthorized access, note the following security recommendations.
General
● You should make regular checks to make sure that the device meets these
recommendations and/or other security guidelines.
● Evaluate your plant as a whole in terms of security. Use a cell protection concept with
suitable products (http://www.industry.siemens.com/topics/global/en/industrialsecurity/network-security/Pages/Default.aspx).
● When the internal and external network are disconnected, an attacker cannot access
internal data from the outside. Therefore operate the device only within a protected
network area.
● For communication via non-secure networks use additional devices with VPN functionality
to encrypt and authenticate the communication.
● Terminate management connections correctly (WBM. Telnet, SSH etc.).
Physical access
● Restrict physical access to the device to qualified personnel because the plug-in data
medium can contain sensitive data.
● Lock unused physical interfaces on the device. Unused interfaces can be used to gain
access to the plant without permission.
Software (security functions)
● Keep the firmware up to date. Check regularly for security updates for the device. You will
find information on this on the Internet pages Industrial Security
(http://www.siemens.com/industrialsecurity).
● Inform yourself regularly about security recommendations by Siemens ProductCERT
(http://www.siemens.com/cert/en/cert-security-advisories.htm).
● Only activate protocols that you require to use the device.
● Restrict access to the management of the device with rules in an access control list
(ACL).
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
35
Safety notices
3.3 Security recommendations
● The option of VLAN structuring provides protection against DoS and unauthorized
access. Check whether this is practical or useful in your environment.
● Use a central logging server to log changes and accesses. Operate your logging server
within the protected network area and check the logging information regularly.
Passwords
● Define rules for the assignment of passwords.
● Regularly change your passwords to increase security.
● Use passwords with a high password strength.
● Make sure that all passwords are protected and inaccessible to unauthorized persons.
● Do not use the same password for different users and systems.
Certificates and keys
● On the device there is a preset SSL certificate with key. Replace this certificate with a
self-made certificate with key. We recommend that you use a certificate signed either by
a reliable external or by an internal certification authority.
● Use a certification authority including key revocation and management to sign certificates.
● Make sure that user-defined private keys are protected and inaccessible to unauthorized
persons.
● It is recommended that you use password-protected certificates in the PKCS #12 format
● Verify certificates and fingerprints on the server and client to prevent "man in the middle"
attacks.
● It is recommended that you use certificates with a key length of at least 2048 bits.
● Change certificates and keys immediately, if there is a suspicion of compromise.
SCALANCE X-200
36
Operating Instructions, 12/2016, C79000-G8976-C284-09
Safety notices
3.3 Security recommendations
Secure/non-secure protocols
● Avoid or disable non-secure protocols, for example Telnet and TFTP. For historical
reasons, these protocols are available, however not intended for secure applications. Use
non-secure protocols on the device with caution.
● Check whether use of the following protocols and services is necessary:
– Non authenticated and unencrypted ports
– MRP, HRP
– LLDP
– DHCP Options 66/67
The following protocols provide secure alternatives:
– HTTP → HTTPS
– TFTP → FTPS
– Telnet → SSH
– SNTP → NTP
– SNMPv1/v2c → SNMPv3
Check whether use of SNMPv1/v2c. is necessary. SNMPv1/v2c are classified as nonsecure. Use the option of preventing write access. The device provides you with
suitable setting options.
If SNMP is enabled, change the community names. If no unrestricted access is
necessary, restrict access with SNMP.
Use the authentication and encryption mechanisms of SNMPv3.
● Use secure protocols when access to the device is not prevented by physical protection
measures.
● If you require non-secure protocols and services, operate the device only within a
protected network area.
● Restrict the services and protocols available to the outside to a minimum.
● For the DCP function, enable the "DCP read-only" mode after commissioning.
Available protocols
The following list provides you with an overview of the open protocol ports.
The table includes the following columns:
● Protocol
● Port
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
37
Safety notices
3.3 Security recommendations
● Port status
– Open
The port is always open and cannot be closed.
– Open (when configured)
The port is open if it has been configured.
● Factory setting
– Open
The factory setting of the port is "Open".
– Closed
The factory setting of the port is "Closed".
● Authentication
Specifies whether or not the protocol is authenticated.
● Encryption
Specifies whether or not the transfer is encrypted.
Protocol
Port number
Port status
Factory setting
Authentication
Encryption
SSH
TCP/22
Open
Open
Yes
Yes
HTTP
TCP/80
Open
Open
Yes
No
HTTPS
TCP/443
Open
Open
Yes
Yes
SNTP
UDP/123
Open
Closed
No
Yes
No
Open
Yes
Yes
(SNMPv3)
Open
Open
No
No
NTP (secure)
SNMP
(when configured)
UDP/161
Open
(when configured)
PROFINET IO
UDP/34964
UDP/1026,
UDP/1027 *)
PROFINET IO
Service
TCP/84
Open
Open
No
No
TELNET
TCP/23
Open
Open
Yes
No
Closed
No
No
Closed
No
No
(when configured)
DHCP
TFTP
UDP/67,
UDP/68
UDP/69
Open
(when configured)
Open
(when configured)
*) These ports are assigned dynamically and can differ from the values specified here.
SCALANCE X-200
38
Operating Instructions, 12/2016, C79000-G8976-C284-09
4
Installation
4.1
Safety notices for installation
Safety notices
When installing the device, keep to the notices listed below.
WARNING
When used in ships, a DIN rail does provide adequate support
For the following devices, installation on a 35 mm DIN rail for use in ships is not permitted:
• X201-3P IRT PRO
• X202-2P IRT PRO
• X204IRT PRO
• X208PRO
• X212-2
• X212-2LD
• X216
• X224
In ships, the DIN rail does not provide adequate support.
WARNING
If the device is installed in a cabinet, the inner temperature of the cabinet corresponds to
the ambient temperature of the device.
WARNING
If a device is operated in an ambient temperature of more than 50 °C, the temperature of
the device housing may be higher than 70 °C. The device must therefore be installed so
that it is only accessible to service personnel or users that are aware of the reason for
restricted access and the required safety measures at an ambient temperature higher than
50 °C.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
39
Installation
4.1 Safety notices for installation
Safety notices on use in hazardous areas
General safety notices relating to protection against explosion
WARNING
EXPLOSION HAZARD
Replacing components may impair suitability for Class 1, Division 2 or Zone 2.
WARNING
The device is suitable only for operation in the interior.
WARNING
The device may only be operated in an environment with pollution degree 1 or 2 (see IEC
60664-1).
WARNING
When used in hazardous environments corresponding to Class I, Division 2 or Class I,
Zone 2, the device must be installed in a cabinet or a suitable enclosure.
Safety notices for use according to ATEX and IECEx
If you use the device under ATEX or IECEx conditions you must also keep to the following
safety notices in addition to the general safety notices for protection against explosion:
WARNING
To comply with EC Directive 2014/34/EU (ATEX 114) or the conditions of IECEx, this
enclosure or cabinet must meet the requirements of at least IP54 in compliance with EN
60529.
Devices with approval [op is Gb] for optical ports
Some devices have an additional ATEX approval according to II 3 (2) G Ex nA [op is
Gb] IIC T4 and an additional IECEx approval according to Ex nA [op is Gb] IIC T4 Gc, refer
to the section Approvals (Page 67). This is indicated on the type plate. With these devices
the FO bus connections may run through or in a Zone 1 hazardous area.
SCALANCE X-200
40
Operating Instructions, 12/2016, C79000-G8976-C284-09
Installation
4.1 Safety notices for installation
WARNING
Cable
If the cable or conduit entry point exceeds 70 °C or the branching point of conductors
exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air
ambient in excess of 50 °C, only use cables with admitted maximum operating temperature
of at least 80 °C.
Safety notices when using according to FM
If you use the device under FM conditions you must also keep to the following safety notices
in addition to the general safety notices for protection against explosion:
WARNING
EXPLOSION HAZARD
For operation the device is intended to be installed within an enclosure/control cabinet. The
inner temperature of the enclosure/control cabinet corresponds to the ambient temperature
of the device. Use installation wiring connections with admitted maximum operating
temperature of at least 30 °C higher than maximum ambient temperature.
Safety notices when using the device acc. to UL 61010-2-201
If you use the device under UL 61010-2-201 conditions you must also keep to the following
safety notices in addition to the general safety notices for protection against explosion:
WARNING
The devices are "open equipment" acc. to the standard UL 61010-2-201. To fulfill
requirements for safe operation with regard to mechanical stability, flame retardation,
stability, and protection against contact, the following alternative types of installation are
specified:
• Installation in a suitable cabinet.
• Installation in a suitable enclosure.
• Installation in a suitably equipped, enclosed control room.
Further notes
NOTICE
Warming and premature aging of the IE switch due to direct sunlight
Direct sunlight can heat up the device and can lead to premature aging of the IE switch and
its cabling.
Provide suitable shade to protect the IE switch against direct sunlight.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
41
Installation
4.2 Installation options
Note
Note the mounting position for XF and TS devices
With the following IE switches, an ambient temperature of maximum +40 °C is permitted if
the device is installed on a vertical rail:
• X204-2TS
• X204-2LD TS
• XF204
• XF204-2
• XF206-1
• XF208
• XF204IRT
4.2
Installation options
Types of installation
IE Switches X-200 can be installed in the following ways:
● Installation on a 35 mm DIN rail complying with DIN EN 60715
● Installation on a SIMATIC S7-300 standard rail
● Wall mounting
Unless stated otherwise, the mounting options listed below apply to all X-200 IE switches.
Exception XF-200
The XF devices (flat design) can only be installed on a 35 mm DIN rail.
Installation clearance
Keep to the following minimum clearances so that the convection ventilation of the device is
not blocked:
● Below at least 10 cm
● Above at least 10 cm
SCALANCE X-200
42
Operating Instructions, 12/2016, C79000-G8976-C284-09
Installation
4.3 Installation on a DIN rail
4.3
Installation on a DIN rail
Installation
Figure 4-1
Installation on a 35 mm DIN rail
To install an X-200 on a 35 mm DIN rail complying with DIN EN 60715, follow the steps
below:
1. Fit the middle locking mechanism of the device on to the DIN rail.
2. Press the device down against the DIN rail until it locks into place.
3. Fit the connectors for the power supply.
4. Fit the connectors for the signaling contact
5. Insert the terminal blocks or M12 cable connectors into the sockets on the device.
Removal
To remove an X-200 from a DIN rail, follow the steps below:
1. First disconnect all connected cables.
2. Use a screwdriver to release the lower DIN rail catch of the device and pull the lower part
of the device away from the rail.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
43
Installation
4.4 Installation on a standard rail
4.4
Installation on a standard rail
Installation on a SIMATIC S7-300 standard rail
To install an X-200 on a standard rail, follow the steps below:
1. Fit the housing guide on the top of the housing into the standard rail.
2. Screw the X-200 to the underside of the standard rail.
3. Fit the connectors for the power supply.
4. Fit the connectors for the signaling contact.
5. Insert the terminal blocks or M12 cable connectors into the sockets on the X-200.
Figure 4-2
Installation on a SIMATIC S7-300 standard rail
Removal
To remove an X-200 from a standard rail, follow the steps below:
1. First disconnect all connected cables.
2. Release the screws on the bottom of the standard rail.
3. Remove the X-200 from the standard rail.
SCALANCE X-200
44
Operating Instructions, 12/2016, C79000-G8976-C284-09
Installation
4.5 Wall mounting
4.5
Wall mounting
Wall mounting
Note
The wall mounting must be capable of supporting at least four times the weight of the X-200,
see section Technical specifications (Page 75).
When mounting on a wall, use mounting fittings suitable for the type of wall. To secure the
device in concrete, you could, for example use the following material:
● 4 wall plugs, 6 mm in diameter and 30 mm long
● 4 screws 3.5 mm in diameter and 40 mm long
Follow the steps below to install the X-200 on a wall:
1. Prepare the drill holes for wall mounting.
You will find the precise dimensions in the Appendix Dimension drawings (Page 87).
2. Connect the electrical cable connecting cables.
3. Fit the connectors for the signaling contact.
4. Insert the terminal blocks or M12 cable connectors into the sockets on the IE Switch X200.
5. Screw the device to the wall.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
45
Installation
4.6 Mounting bus adapters
4.6
Mounting bus adapters
Required tool:
● Slotted screwdriver, blade width 3 to 3.5 mm
or
● Torx screwdriver, size T10
Installation
Figure 4-3
Mounting bus adapters
To fit a bus adapter, follow the steps below:
1. Plug the bus adapter parallel into the BaseUnit until it can be heard to lock in place.
2. Screw the bus adapter to the BaseUnit of the device with the included screw (tightening
torque 0.2 Nm).
To do this, use a screwdriver with a 3 to 3.5 mm blade.
3. Insert the connection plugs into the sockets intended for this on the bus adapter.
Removal
To remove a bus adapter, follow the steps below:
1. First disconnect all connected cables.
2. Loosen the screw connection of the bus adapter.
3. Pull the bus adapter out of the Base Unit to the front.
SCALANCE X-200
46
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.1
5
Safety when connecting up
Safety notices
When connecting up the device, keep to the safety notices listed below.
WARNING
The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a
Limited Power Source (LPS).
This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1
must be connected to the power supply terminals. The power supply unit for the equipment
power supply must comply with NEC Class 2, as described by the National Electrical Code
(r) (ANSI / NFPA 70).
If the equipment is connected to a redundant power supply (two separate power supplies),
both must meet these requirements.
Note
Limitation of the output voltage according to NEC Class 2 by redundancy module
To meet the requirements according to NEC Class 2, you can use a power supply with SELV
along with a power limiter, see e.g. the section "Accessories (Page 20)".
Note
Safety extra-low voltage
The supply of the devices by PELV (Protective Extra Low Voltage) according to DIN VDE
0100-410 or IEC 60364-4-41 is permitted when the generated nominal voltage does not
exceed the voltage limits 25 VAC or 60 VDC.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
47
Connecting up
5.1 Safety when connecting up
Safety notices on use in hazardous areas
General safety notices relating to protection against explosion
WARNING
EXPLOSION HAZARD
Do not connect or disconnect cables to or from the device when a flammable or
combustible atmosphere is present.
Exceptions
For the devices listed below, there are no requirements according to NEC Class 2 or LPS.
For these devices, note the conditions described in the section Supply for IRT-PRO devices
(Page 52).
● X201-3P IRT PRO
● X202-2P IRT PRO
● X204IRT PRO
Safety notices when using the device according to Hazardous Locations (HazLoc)
If you use the device under HazLoc conditions you must also keep to the following safety
notices in addition to the general safety notices for protection against explosion:
WARNING
EXPLOSION HAZARD
Do not connect or disconnect while the circuit is live or unless the area is known to be free
of ignitible concentrations.
Safety notices for use according to ATEX and IECEx
If you use the device under ATEX or IECEx conditions you must also keep to the following
safety notices in addition to the general safety notices for protection against explosion:
WARNING
Take measures to prevent transient voltage surges of more than 40% of the rated voltage.
This is the case if you only operate devices with SELV (safety extra-low voltage).
SCALANCE X-200
48
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.1 Safety when connecting up
Further notes
WARNING
Cable
If the cable or conduit entry point exceeds 70 °C or the branching point of conductors
exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air
ambient in excess of 50 °C, only use cables with admitted maximum operating temperature
of at least 80 °C.
WARNING
Safety notice for connecting with a LAN ID (Local Area Network)
A LAN or LAN segment with all the interconnected devices should be contained completely
in a single low voltage power distribution in a building. The LAN is designed either for
“Environment A” according to IEEE802.3 or "Environment 0" according to IEC TR 62102.
Do not connect any electrical connectors directly to the telephone network (telephone
network voltage) or a WAN (Wide Area Network).
CAUTION
Electric shock - turn off the power supply
Turn off the power supply before you connect or disconnect cables from the device.
NOTICE
Overvoltage protection
If IE Switches X-200 are supplied over long 24 V power supply lines or networks, measures
are necessary to prevent interference by strong electromagnetic pulses on the supply lines.
These can result, for example, due to lightning or switching of large inductive loads.
One of the tests used to attest the immunity of devices of the IE Switches X-200 to
electromagnetic interference was the "surge immunity test" according to EN61000-4-5. This
test requires overvoltage protection for the power supply lines. A suitable device is, for
example, the Dehn Blitzductor BVT AVD 24 V type no. 918 422 or a comparable protective
element.
Manufacturer: DEHN+SÖHNE GmbH+Co.KG, Hans-Dehn-Str.1, Postfach 1640, D-92306
Neumarkt, Germany.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
49
Connecting up
5.2 Wiring rules
5.2
Wiring rules
When wiring use cables with the following AWG categories or cross sections.
Wiring rules for ...
connectable cable cross sections for flexible cables ...
Screw/spring-loaded terminals
without wire end ferrule
0.25 - 2.5 mm2
AWG: 24 - 13
with wire end ferrule with plastic ferrule**
0.25 - 2.5 mm2
with wire end ferrule without plastic
ferrule**
0.25 - 2.5 mm2
with TWIN wire end ferrule**
0.5 - 1 mm2
AWG: 24 - 13
AWG: 24 - 13
AWG: 20 - 17
Stripped length of the cable
8 - 10 mm
Wire end ferrule according to DIN 46228 with plastic ferrule**
8 - 10 mm
* AWG: American Wire Gauge
** See note "Wire end ferrules"
Note
Wire end ferrules
Use crimp shapes with smooth surfaces, such as provided by square and trapeze shaped
crimp cross sections.
Crimp shapes with wave-shaped profile are unsuitable.
SCALANCE X-200
50
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.3 Power supply
5.3
Power supply
5.3.1
Supply with X-200 via the terminal block
Power supply
The power supply is connected via a 4-pin plug-in terminal block that ships with the device.
● The power supply can be connected redundantly.
– Both inputs are isolated.
– No load distribution.
– The power supply unit with the higher output voltage supplies the device alone.
● Power: 24 VDC
● Cable cross section for X-200: 2.5 mm2
● Cable cross section for XF-200: 1.5 mm2
● The power supply is connected over a high resistance with the enclosure to allow an
ungrounded set up.
● The power supply is non-floating.
● The signal cables of the electrical Ethernet interfaces are floating.
The following table shows the pin assignment:
Assignment
L1+: 24 VDC
With TS devices:
L1+: 12 to 24 VDC
M1: Ground
M2: Ground
L2+ 24 VDC
With TS devices:
L2+ 12 to 24 VDC
Note
Special features with X208PRO and the IRT-PRO devices
Note the special requirements for the power supply for the devices in the following sections.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
51
Connecting up
5.3 Power supply
5.3.2
Supply for X208PRO
Power supply for X208PRO
With the IE switch SCALANCE X208PRO, the power supply is connected via two 4-pin acoded M12 sockets.
● The power supply can be connected redundantly.
– Both inputs are isolated.
– No load distribution.
– The power supply unit with the higher output voltage supplies the device alone.
● Power: 24 VDC
● The power supply is connected over a high resistance with the enclosure to allow an
ungrounded set up.
● The power supply is non-floating.
● The signal cables of the electrical Ethernet interfaces are floating.
The following table shows the pin assignment:
Pin no.:
5.3.3
Assignment
1
L1 or L2: 24 VDC
2
n. c.
3
M1 or M2
4
n. c.
Supply for IRT-PRO devices
Power supply for the devices of the IRT PRO version
The following descriptions of the power supply apply to the following devices:
● X201-3P IRT PRO
● X202-2P IRT PRO
● X204IRT PRO
The power supply is connected via the push-pull Power Plug PRO. This plug has a high
degree of protection (IP65) and is suitable for use outside cabinets and complies with
PROFINET connector technology.
The Power Plug PRO does not ship with the device, see the section “Accessories
(Page 20)“:
SCALANCE X-200
52
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.3 Power supply
Power supply
● Power: 24 VDC
● The power supply is connected over a high resistance with the enclosure to allow an
ungrounded set up.
● The power supply is non-floating.
● The signal cables of the electrical Ethernet interfaces are floating.
Note
No redundant power supply
Since the IRT PRO version of the devices does not have a redundant power supply, connect
the power supply to L1 and N1.
Note
Plug in metal casing
• If the devices are operated at an ambient temperature in excess of 40 °C or if currents
higher than 6 A flow via the connector, the connector with the metal casing must be used.
• In areas subject to the National Electric Code (NEC), the Canadian Electric Code (CEC)
and the EC directive 94/9 (ATEX) and IECEx, metal connectors must be used.
Note
Maximum current 16 A
The current through the Power Plug PRO must not exceed 16 A. You should therefore
include a fuse that trips at a current higher than 16 A.
In areas subject to the NEC or CEC, the fuse must meet the following requirements:
• Suitable for DC (min. 60 V / max. 16 A)
• Breaking current at least 10 kA
• UL / CSA listed (UL 248-1 / CSA 22.2 No. 248.1)
• Classes R, J, L, T or CC.
Otherwise the following requirements must be met:
• Suitable for DC (min. 60 V / max. 16 A)
• Breaking current at least 10 kA
• Approved according to IEC/EN 60127-1
• Breaking characteristics
– With circuit breakers: B or C
– With fuses: slow blow
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
53
Connecting up
5.3 Power supply
Power supply looped through
The devices also have a connector for the switched mode and unswitched power supply of
other devices with 24 VDC. Via these interfaces (L1+, N1 and L2+, N2) it is possible to loop
the power through with connector technology compliant with PROFINET.
You should also refer to the manual "SIMATIC Distributed IO System ET 200pro
(https://support.industry.siemens.com/cs/ww/en/view/21210852)".
Note
Notes on operating under marginal conditions
When looping through the power supply, take into account the limit values; in other words,
the maximum permitted current depending on the ambient temperature; refer to the table
"Operation under marginal conditions" below.
When looping through the power supply under the marginal conditions described below, the
device may only be operated if it is installed horizontally. Horizontal installation position
means that the device is mounted, for example on a horizontal DIN or standard rail or that
the labeling on the device can be read in the normal reading direction.
If no power is looped through, any installation position is permitted.
Table 5- 1
Operation under marginal conditions
Environment
Max Power 1 (L1+, N1)
Max Power 2 (L2+, N2)
+40℃
16 A
16 A
+50℃
12 A
12 A
+60℃
8A
8A
6A
6A
SCALANCE X204IRT PRO only:
+70°C
Pin assignment of the connectors
The following table shows the pin assignment of the two power supply connectors:
Pin no.:
Assignment
1
L1: 24 VDC
2
N1
3
L2: 24 VDC
4
N2
5
FE (Functional Earth)
SCALANCE X-200
54
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.3 Power supply
5.3.4
Supply with XF-200IRT devices with bus adapter slots
Power supply for devices with bus adapter slots
The following descriptions of the power supply apply to the following devices:
● XF204-2BA IRT
The power supply is connected via two 2-pin plug-in terminal blocks that ship with the
device.
Power supply
● The power supply can be connected redundantly.
– Both inputs are isolated.
– No load distribution.
– The power supply unit with the higher output voltage supplies the device alone.
● Power: 24 VDC
● Cable cross-section: max. 2.5 mm2
● The power supply is connected over a high resistance with the enclosure to allow an
ungrounded set up.
● The power supply is non-floating.
● The signal cables of the electrical Ethernet interfaces are floating.
The following table shows the pin assignment:
Assignment
L+: 24 VDC
M: Ground
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
55
Connecting up
5.4 Grounding
5.4
Grounding
Grounding when installing on a DIN rail
The device is grounded over the DIN rail.
Grounding when installing on an S7 standard rail
The device is grounded over its rear panel and the neck of the screw.
Grounding with wall mounting
The device is grounded by the securing screw in the unpainted hole.
Please note that X-200 IE switches must be grounded over one securing screw with
minimum resistance.
If an IE Switch X-200 is mounted on a non-conducting base, a grounding cable must be
installed. The grounding cable is not supplied with the device. Connect the paint-free surface
of the device to the nearest grounding point using the grounding cable.
SCALANCE X-200
56
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.5 Signaling contact
5.5
Signaling contact
Signaling contact
The signaling contact or relay contact is a floating switch with which error/fault states can be
signaled by breaking the contact.
The following errors/faults can be signaled by the signaling contact:
● The loss and the establishment of a link on a monitored port.
● The failure of one of the two redundant power supplies.
Note: Devices of the IRT PRO version do not have a redundant power supply
● The loss of the connection to the controller in PROFINET IO mode.
● The redundancy manager signals an error
● An incompatible C-PLUG was inserted.
The connection or disconnection of a communication node on an unmonitored port does not
lead to an error message.
The signaling contact remains activated until the error/fault is eliminated or until the current
status is applied as the new desired status using the SET button.
When the IE Switch X-200 is turned off, the signaling contact is always activated, i.e.
opened.
NOTICE
Load on the signaling contact
The signaling contact can be subjected to a maximum load of 100 mA (safety extra-low
voltage (SELV), 24 VDC).
Connection via 2-pin terminal block
The signaling contact is connected to a 2-pin plug-in terminal block.
The following table shows the pin assignment:
Assignment
F1: Fault contact 1
F2: Fault contact 2
SCALANCE X-200, XF-200, X200IRT
SCALANCE XF-200IRT
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
57
Connecting up
5.5 Signaling contact
Connection via M12 socket
With the X-200 IRT PRO devices and with the X208PRO, the connection is via a 5-pin, bcoded M12 socket.
The following table shows the pin assignment:
Pin
no.:
1
Assignment
F1
2
n.c.
3
n.c.
4
F2
5
n.c.
SCALANCE X-200 IRT PRO
SCALANCE X-200
58
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.6 Attachment to Industrial Ethernet
5.6
Attachment to Industrial Ethernet
Note
Redundancy mechanisms
If you use redundancy mechanisms such as media redundancy "HRP" or "MRP" and/or
redundant linking of rings via a standby link, remember the following:
Open the redundant path before you insert a new device or replacement device in an
operating network. A bad configuration or attachment of the Ethernet cables to incorrectly
configured ports causes overload in the network and a breakdown in communication.
A device may only be inserted in a network and connected in the following situations:
• HRP / MRP
– The ring ports of the device being inserted in the ring were configured as ring ports.
– The required redundancy mode is also enabled.
– If the device is intended to operate as the redundancy manager, "Enable Ring
Redundancy" must also be set.
• Standby link
– Select "Enable Standby Master".
– The "Standby Connection Name" must match the name of the partner device.
– You must also configure the standby port.
You will find detailed information in the SCALANCE X-200 configuration manual.
5.6.1
Electrical connections
Note
Strain relief of the interfaces
To prevent weights or mechanical movement that can affect an interface causing interrupted
contact, fix the cables to a cable guide or rail at short intervals.
5.6.1.1
Electrical attachments to Industrial Ethernet
Connection via RJ-45 jacks
The electrical connectors for Industrial Ethernet on the X-200 IE switch are designed as RJ45 jacks with the following properties:
● MDI-X assignment
● Autonegotiation
● Auto polarity exchange
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
59
Connecting up
5.6 Attachment to Industrial Ethernet
MDI / MDI-X autocrossover function
The advantage of this function is that straight-through cables can be used throughout and
external Ethernet crossover cables are unnecessary. This prevents malfunctions resulting
from mismatching send and receive wires. This makes installation much easier for the user.
Note
Formation of loops
Please note that the direct connection of two ports on the switch or accidental connection
over several switches causes an illegal loop. Such a loop can lead to network overload and
network failures.
Autonegotiation
Autonegotiation means the automatic detection of the functionality of the port at the opposite
end. Using autonegotiation, repeaters or end devices can detect the functionality available at
the port of a partner device allowing automatic configuration of different types of device. With
autonegotiation, two components connected to a link segment can exchange parameters
and set themselves to match the supported communication functionality.
Note
• If a port operating in autonegotiation mode is connected to a partner device that is not
operating in autonegotiation mode, the partner device must be set permanently to half
duplex mode.
• If a port is set permanently to full duplex, the connected partner device must also be set
to full duplex.
• If the autonegotiation function is disabled, the MDI/MDI-X autocrossover function is also
inactive. This means it may be necessary to use a crossover cable.
Auto polarity exchange
If the pair of receiving cables is incorrectly connected, in other words, RD+ and RD- are
swapped over, the polarity is reversed automatically.
SCALANCE X-200
60
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.6 Attachment to Industrial Ethernet
PIN assignment
The following table shows the pin assignment of the RJ-45 connectors:
Pin no.:
Assignment
8
n. c.
7
n. c.
6
TD-
5
n. c.
4
n. c.
3
TD
2
RD-
1
RD+
Permitted cable lengths
● With connection using TP cords or TP-XP cords: maximum 10 m
● When connected using IE FC cable with IE RJ-45 plug:
Depending on the cable type, a total length of up to 100 m is permitted between two
devices.
5.6.1.2
Electrical connectors of the X208PRO
Connection via M12 sockets
With the IE switch SCALANCE X208PRO, the connection to Industrial Ethernet is via 4-pin,
d-coded M12 sockets with MDI-X assignment.
MDI / MDI-X autocrossover function
The advantage of this function is that straight-through cables can be used throughout and
external Ethernet crossover cables are unnecessary. This prevents malfunctions resulting
from mismatching send and receive wires. This makes installation much easier for the user.
Note
Formation of loops
Please note that the direct connection of two ports on the switch or accidental connection
over several switches causes an illegal loop. Such a loop can lead to network overload and
network failures.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
61
Connecting up
5.6 Attachment to Industrial Ethernet
PIN assignment
The following table shows the pin assignment of the M12 sockets:
Pin no.:
Assignment
1
RX+
2
TX+
3
RX-
4
TX-
Permitted cable lengths
● With connection using TP cords or TP-XP cords: maximum 10 m
● When connected using IE FC cable with IE RJ-45 plug:
Depending on the cable type, a total length of up to 100 m is permitted between two
devices.
IE FC M12 plug PRO
The IE FC M12 Plug PRO has a high degree of protection (IP65/67) and is suitable for
connecting the X208PRO to Industrial Ethernet. You can obtain this plug using the following
order number: 6GK1 901-0DB20-6AA0.
5.6.2
Optical attachments to Industrial Ethernet
NOTICE
Failure of the data traffic due to contamination of optical plug-in connections
Optical sockets and plugs are sensitive to contamination of the end face. Contamination
can lead to the failure of the optical transmission network.
Close unused optical sockets and plugs as well as pluggable transceivers and slots with the
supplied protective caps.
Remove the protective caps only immediately before you use the plug-in connection.
SCALANCE X-200
62
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.6 Attachment to Industrial Ethernet
5.6.2.1
Multimode fiber-optic cable
Transmission medium
The following X-200 IE switches use multimode fiber-optic cables as the transmission
medium:
● X204-2
● X204-2TS
● X204-2FM
● X206-1
● X212-2
● XF204-2
● XF206-1
● X202-2IRT
● XF204-2BA IRT with corresponding bus adapter
Characteristics:
Transmission speed
100 Mbps
Transmission mode
100Base-FX according to IEEE 802.3
Connectors
BFOC sockets
Wavelength
1300 nm
Core diameter
50 or 62.5 μm
Outer diameter
125 μm
Light source
LED
Maximum range (segment length)
5 km
Note
No autonegotiation
With optical transmission, the full duplex mode and transmission speed cannot be changed.
For this reason, the autonegotiation function cannot be selected.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
63
Connecting up
5.6 Attachment to Industrial Ethernet
5.6.2.2
Single mode fiber-optic cable
Transmission medium
The following X-200 IE switches use single mode fiber-optic cables as the transmission
medium:
● X204-2LD
● X204-2LD TS
● X206-1LD
● X212-2LD
Characteristics:
Transmission speed
100 Mbps
Transmission mode
100Base LX
Connectors
BFOC sockets
Wavelength
1310 nm
Core diameter
9 μm
Outer diameter
125 μm
Light source
LED
Maximum range (segment length)
26 km
Note
No autonegotiation
With optical transmission, the full duplex mode and transmission speed cannot be changed.
For this reason, the autonegotiation function cannot be selected.
5.6.2.3
POF and PCF cables
Transmission medium
The following X-200 IE switches use Plastic Optical Fiber (POF) or Polymer Cladded Fiber
(PCF) as the transmission medium:
● X200-4P IRT
● X201-3P IRT
● X201-3P IRT PRO
● X202-2P IRT
● X202-2P IRT PRO
● XF204-2BA IRT with corresponding bus adapter
SCALANCE X-200
64
Operating Instructions, 12/2016, C79000-G8976-C284-09
Connecting up
5.6 Attachment to Industrial Ethernet
Characteristics:
Transmission speed
100 Mbps
Transmission mode
100Base-FX analogous to IEEE 802.3
Connectors
SC RJ jacks
Wavelength
650 nm
Core diameter
•
with POF
•
980 μm
•
with PCF
•
200 μm
Outer diameter
•
with POF
•
1000 μm
•
with PCF
•
230 μm
Light source
LED
Cable lengths
•
minimum
•
0m
•
maximum segment length
•
50 m for POF
100 m for PCF
Signal attenuation
•
with POF
•
0.230 dB/m
•
with PCF
•
0.01 dB/m
Note
No autonegotiation
With optical transmission, the full duplex mode and transmission speed cannot be changed.
For this reason, the autonegotiation function cannot be selected.
GI-PCF
For segment lengths longer than 100 m, you can use GI-PCF cables. Note the information of
the manufacturer.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
65
Connecting up
5.6 Attachment to Industrial Ethernet
5.6.3
Push-pull connector for IRT-PRO devices
Push-pull connector technology
With the following devices, the connection to Industrial Ethernet makes use of the
PROFINET-compliant push-pull connector technology:
● X204IRT PRO
● X202-2P IRT PRO
● X201-3P IRT PRO
Due to their high degree of protection (IP65), the push-pull connectors are suitable for
installation outside cabinets. The plugs do not ship with the product, see the section
“Accessories (Page 20)“.
SCALANCE X-200
66
Operating Instructions, 12/2016, C79000-G8976-C284-09
6
Approvals
Approvals issued
Note
Issued approvals on the type plate of the device
The specified approvals apply only when the corresponding mark is printed on the product.
You can check which of the following approvals have been granted for your product by the
markings on the type plate.
Approvals for shipbuilding are not printed on the device type plate.
Current approvals on the Internet
You will find the current approvals for the product on the Internet pages of Siemens Industry
Online Support.
33118791 (http://support.automation.siemens.com/WW/view/en/33118791)
Approvals for SIMATIC NET products
You will find an overview of the approvals for SIMATIC NET products including approvals for
shipbuilding on the Internet pages of Siemens Industry Online Support:
57337426 (http://support.automation.siemens.com/WW/view/en/57337426)
Installation guidelines
The devices meet the requirements if you adhere to the installation and safety instructions
contained in this documentation and in the following documentation when installing and
operating the devices.
● "Industrial Ethernet / PROFINET Industrial Ethernet" System Manual
● "Industrial Ethernet / PROFINET - Passive network components" System Manual
You will find information on the system manuals in the section "AUTOHOTSPOT", in
"Further documentation".
● "EMC Installation Guidelines" configuration manual
60612658 (http://support.automation.siemens.com/WW/view/en/60612658)
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
67
Approvals
WARNING
Personal injury and property damage can occur
The installation of expansions that are not approved for SIMATIC NET products or their
target systems may violate the requirements and regulations for safety and electromagnetic
compatibility.
Only use expansions that are approved for the system.
Note
The test was performed with a device and a connected communications partner that also
meets the requirements of the standards listed above.
When operating the device with a communications partner that does not comply with these
standards, adherence to the corresponding values cannot be guaranteed.
EC declaration of conformity
The SIMATIC NET products described in these operating instructions meet the requirements
and safety objectives of the following EC directives and comply with the harmonized
European standards (EN) which are published in the official documentation of the European
Union.
● 2014/34/EU (ATEX explosion protection directive)
Directive of the European Parliament and the Council of 26 February 2014 on the
approximation of the laws of the member states concerning equipment and protective
systems intended for use in potentially explosive atmospheres, official journal of the EU
L96, 29/03/2014, pages. 309-356
● 2014/30/EU (EMC)
EMC directive of the European Parliament and of the Council of February 26, 2014 on the
approximation of the laws of the member states relating to electromagnetic compatibility;
official journal of the EU L96, 29/03/2014, pages. 79-106
● 2011/65/EU (RoHS)
Directive of the European Parliament and of the Council of 8 June 2011 on the restriction
of the use of certain hazardous substances in electrical and electronic equipment
You will find the EC declaration of conformity for these products on the Internet pages of
Siemens Industry Online Support
(http://support.automation.siemens.com/WW/view/en/33118389/134200).
The EC Declaration of Conformity is available for all responsible authorities at:
Siemens Aktiengesellschaft
Division Process Industries and Drives
Process Automation
DE-76181 Karlsruhe
Germany
SCALANCE X-200
68
Operating Instructions, 12/2016, C79000-G8976-C284-09
Approvals
EC directives
SIMATIC NET products meet the requirements and aims of the following EC directives.
EMC directive (electromagnetic compatibility)
Until 19.042016 the SIMATIC NET products described in these operating instructions meet
the requirements of the EC Directive:2004/108/EC "Electromagnetic Compatibility” (EMC
directive) and as of 20.04.2016 the EC directive 2014/30/EU.
Field of application
Industry
Requirements
Emission
Immunity to interference
EN 61000-6-4
EN 61000-6-2
You will find the current versions of the standards in the currently valid EC declaration of
conformity.
Explosion protection directive (ATEX)
The product meets the requirements of the EC directive:2014/34/EC "Equipment and
Protective Devices for Use in Potentially Explosive Atmospheres".
You will find the current versions of the standards in the currently valid ATEX certificates.
II 3 G Ex nA IICT4 Gc
The IE switches SCALANCE X-200 meet the requirements according to
II 3 G Ex nA IIC T4 Gc, certificate no.: KEMA 07ATEX0145 X:
•
X204-2
•
XF204-2
•
X204-2TS
•
XF206-1
•
X204-2FM
•
XF208
•
X204-2LD
•
X200-4P IRT
•
X204-2LD TS
•
X201-3P IRT
•
X206-1
•
X201-3P IRT PRO
•
X206-1LD
•
X202-2IRT
•
X208
•
X202-2P IRT
•
X208PRO
•
X202-2P IRT PRO
•
X212-2
•
X204IRT
•
X212-2LD
•
X204IRT PRO
•
X216
•
XF204IRT
•
X224
•
XF204-2BA IRT
•
XF204
These products meet the requirements of the following standards:
● EN 60079-15
● EN 60079-0
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
69
Approvals
II 3 (2) G Ex nA [op is] IIC T4
The IE switches SCALANCE X-200 listed below have additional approval according to
II 3 (2) G Ex nA [op is] IIC T4, certificate no.: DEKRA11ATEX0060 X:
•
X204-2
•
XF204-2
•
X204-2TS
•
XF206-1
•
X204-2FM
•
X202-2IRT
•
X206-1
•
X212-2
These products meet the requirements of the following standards:
● EN 60079-0
● EN 60079-15
● EN 60079-28
IECEx
The SIMATIC NET products meet the requirements of explosion protection according to
IECEx.
IECEx classification:
Ex nA IIC T4 Gc
DEK 14.0025X
The products meet the requirements of the following standards:
● IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of
protection "n")
● IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
You will find the current versions of the standards in the currently valid IECEx certificates.
SCALANCE X-200
70
Operating Instructions, 12/2016, C79000-G8976-C284-09
Approvals
The following SCALANCE X-200 IE switches meet these requirements:
•
X204-2
•
XF204-2
•
X204-2TS
•
XF206-1
•
X204-2FM
•
XF208
•
X204-2LD
•
X200-4P IRT
•
X204-2LD TS
•
X201-3P IRT
•
X206-1
•
X201-3P IRT PRO
•
X206-1LD
•
X202-2IRT
•
X208
•
X202-2P IRT
•
X208PRO
•
X202-2P IRT PRO
•
X212-2
•
X204IRT
•
X212-2LD
•
X204IRT PRO
•
X216
•
XF204IRT
•
X224
•
XF204-2BA IRT
•
XF204
IECEx (optical radiation)
The SIMATIC NET products meet the requirements of explosion protection according to
IECEx.
IECEx classification:
Ex nA [op is Gb] IIC T4 Gc
DEK 14.0026X
The products meet the requirements of the following standards:
● IEC 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of
protection "n")
● IEC 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
● IEC 60079-28 (Explosive atmospheres - Part 28: Protection of equipment and
transmission systems using with optical radiation)
You will find the current versions of the standards in the currently valid IECEx certificates.
The following SCALANCE X-200 IE switches also meet these requirements:
•
X204-2
•
XF204-2
•
X204-2TS
•
XF206-1
•
X204-2FM
•
X202-2IRT
•
X206-1
•
X212-2
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
71
Approvals
FM
The product meets the requirements of the standards:
● Factory Mutual Approval Standard Class Number 3611
● FM Hazardous (Classified) Location Electrical Equipment:
Non Incendive / Class I / Division 2 / Groups A,B,C,D / T4 and
Non Incendive / Class I / Zone 2 / Group IIC / T4
cULus approval for industrial control equipment
cULus Listed IND. CONT. EQ.
Underwriters Laboratories Inc. complying with
● UL 508
● CSA C22.2 No. 142-M1987
Report no. E85972
cULus approval for industrial control equipment
cULus Listed IND. CONT. EQ.
Underwriters Laboratories Inc. complying with
● UL 61010-2-201
● CAN/CSA-IEC 61010-2-201
Report no. E85972
cULus Approval for Information Technology Equipment
cULus Listed I. T. E.
Underwriters Laboratories Inc. complying with
● UL 60950-1 (Information Technology Equipment)
● CSA C22.2 No. 60950-1-03
Report no. E115352
SCALANCE X-200
72
Operating Instructions, 12/2016, C79000-G8976-C284-09
Approvals
cULus Approval Hazardous Location
cULus Listed I. T. E. FOR HAZ. LOC.
Underwriters Laboratories Inc. complying with
● UL 60950-1 (Information Technology Equipment)
● ANSI/ISA 12.12.01-2007
● CSA C22.2 No. 213-M1987
Approved for use in
Cl. 1, Div. 2, GP A, B, C, D T4
Cl. 1, Zone 2, GP IIC T4
Report no. E240480
CSA Approval for Information Technology Equipment
CSA Certification Mark
Canadian Standard Association CSA C22.2 No. 60950-1-03
CSA Approval for Industrial Control Equipment
CSA Certification Mark
Canadian Standard Association CSA C22.2 No. 142-1987
FDA and IEC approvals
The following SCALANCE X-200 switches meet the FDA and IEC requirements listed below:
● X204-2LD
● X204-2LD TS
● X206-1LD
● X212-2LD
Figure 6-1
FDA and IEC approvals
CAUTION
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
73
Approvals
RCM
The product meets the requirements of the AS/NZS 2064 standard (Class A).
MSIP 요구사항 - For Korea only
A급 기기(업무용 방송통신기자재)
이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기
바라며, 가정 외의 지역에서 사용하는것을 목적으로 합니다.
Marking for the customs union
EAC (Eurasian Conformity)
Customs union of Russia, Belarus and Kazakhstan
Declaration of the conformity according to the technical regulations of the customs union
(TR CU)
Railway approval
The TS variant of the device meets the requirements of the Railway standard EN
50155:2007 "Railway Applications - Electronic equipment used on rolling stock".
SCALANCE X-200
74
Operating Instructions, 12/2016, C79000-G8976-C284-09
7
Technical specifications
Construction
Type
Dimensions (W x H x D) in mm
Weight in g
Installation options
- DIN rail
- S7-300 standard rail
- Wall mounting
X204-2
60 x 125 x 124
780
+
X204-2TS
60 x 125 x 124
780
+
X204-2FM
60 x 125 x 124
780
+
X204-2LD
60 x 125 x 124
780
+
X204-2LD TS
60 x 125 x 124
780
+
X206-1
60 x 125 x 124
780
+
X206-1LD
60 x 125 x 124
780
+
X208
60 x 125 x 124
780
+
X208PRO
90 x 125 x 124
1000
+
X212-2
120 x 125 x 124
1200
+
X212-2LD
120 x 125 x 124
1200
+
X216
120 x 125 x 124
1200
+
X224
180 x 125 x 124
1600
+
XF204
75 x 125 x 73
250
DIN rail mounting only
XF204-2
75 x 125 x 73
250
DIN rail mounting only
XF206-1
75 x 125 x 73
250
DIN rail mounting only
XF208
75 x 125 x 73
250
DIN rail mounting only
X200-4P IRT
60 x 125 x 124
780
+
X201-3P IRT
60 x 125 x 124
780
+
X201-3P IRT PRO
90 x 125 x 124
1000
+
X202-2IRT
60 x 125 x 124
780
+
X202-2P IRT
60 x 125 x 124
780
+
X202-2P IRT PRO
90 x 125 x 124
1000
+
X204IRT
60 x 125 x 124
780
+
X204IRT PRO
90 x 125 x 124
1000
+
XF204IRT
75 x 125 x 73
250
DIN rail mounting only
XF204-2BA IRT
100 x 117,1 x 74
250
DIN rail mounting only
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
75
Technical specifications
Ports
Type
Connectors for end devices or network components via twisted pair
Connections for end
devices or network components via FO cable
RJ-45 jacks with MDI X
pinning
10/100 Mbps (half / full
duplex) 1)
BFOC sockets
(100 Mbps, full duplex to
100BaseFX)
Connectors for power
supply
Connectors for
signaling contact
4-pin plug-in terminal
block, redundant 2)
2-pin plug-in terminal
block 3)
X204-2
4
2
1
1
X204-2TS
4
2
1
1
X204-2FM
4
2
1
1
X204-2LD
4
2
1
1
X204-2LD TS
4
2
1
1
X206-1
6
1
1
1
X206-1LD
6
1
1
1
X208
8
-
1
1
X208PRO
8 1)
-
1 2)
1 3)
X212-2
12
2
1
1
X212-2LD
12
2
1
1
X216
16
-
1
1
X224
24
-
1
1
XF204
4
-
1
1
XF204-2
4
2
1
1
XF206-1
6
1
1
1
XF208
8
-
1
1
X202-2IRT
2
2
1
1
X204IRT
4
-
1
1
XF204IRT
4
-
1
1
1) Exception X208PRO: Connection via 4-pin, d-coded M12 socket, IP65/67.
2) Exception X208PRO: Connection via 4-pin, a-coded M12 socket, IP65/67.
3) Exception X208PRO: Connection via 5-pin, b-coded M12 socket, IP65/67.
Type
Connectors for end devices or network components via twisted pair
Connections for end
devices or network components via FO cable
RJ-45 jacks with MDI X
pinning
10/100 Mbps (half / full
duplex)
SC RJ jacks (push-pull)
(100 Mbps, full duplex to
100BaseFX)
Connector for power
supply
Connector for signaling
contact
4-pin plug-in terminal
block, redundant
2-pin plug-in terminal
block
X200-4P IRT
-
4
1
1
X201-3P IRT
1
3
1
1
X202-2P IRT
2
2
1
1
Type
XF204-2BA IRT
Slots for bus adapters
2
Connector for power supply
Connector for signaling contact
2-terminal plug-in block
2-terminal plug-in block
2
1
SCALANCE X-200
76
Operating Instructions, 12/2016, C79000-G8976-C284-09
Technical specifications
Type
Connectors for end devices or network components via twisted pair
Connections for end
devices or network components via FO cable
RJ-45 jacks with MDI X
pinning
10/100 Mbps half / full
duplex
SC RJ jacks (push-pull),
100 Mbps, full duplex to
100BaseFX
Connector for power
supply
Connector for signaling
contact
5-pin Power Plug PRO
connector (male)
5-pin b-coded M12 connector (male)
X201-3P IRT PRO
1
3
2
1
X202-2P IRT PRO
2
2
2
1
X204IRT PRO
4
-
2
1
Signaling contact
The following applies to all devices:
● Voltage for the signaling contact: 24 VDC
● Current through the signaling contact: maximum 100 mA
Electrical data
Type
Supply voltage with redundant connection
Power loss at 12 VDC
Current consumption at
rated voltage
Overcurrent protection at
input
Non-replaceable fuse (F)
Rated voltage 12 to 24
VDC SELV
Voltage range 10 VDC to
28.8 VDC
Permitted voltage range
incl. total ripple 10 VDC to
30.2 VDC
X204-2TS
+
6.60 W
600 mA
3.0 A / 32 V
X204-2LD TS
+
6.60 W
600 mA
3.0 A / 32 V
Power loss at 24 VDC
Current consumption at
rated voltage
Overcurrent protection at
input
PTC resettable fuse
Type
Supply voltage with redundant connection
Rated voltage 24 VDC
Voltage range 19.2 VDC
to 28.8 VDC
Permitted voltage range
incl. total ripple 18.5 VDC
to 30.2 VDC
X204-2
+
6.36 W
265 mA
600 mA / 60 V
X204-2FM
+
6.36 W
265 mA
600 mA / 60 V
X204-2LD
+
6.36 W
265 mA
600 mA / 60 V
X206-1
+
5.28 W
220 mA
600 mA / 60 V
X206-1LD
+
5.28 W
220 mA
600 mA / 60 V
X208
+
3.84 W
185 mA
600 mA / 60 V
X208PRO
+
4.4 W
185 mA
600 mA / 60 V
X212-2
+
7.92 W
330 mA
1.1 A / 33 V
X212-2LD
+
7.92 W
330 mA
1.1 A / 33 V
X216
+
5.76 W
240 mA
1.1 A / 33 V
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
77
Technical specifications
Type
Supply voltage with redundant connection
Power loss at 24 VDC
Current consumption at
rated voltage
Overcurrent protection at
input
PTC resettable fuse
Rated voltage 24 VDC
Voltage range 19.2 VDC
to 28.8 VDC
Permitted voltage range
incl. total ripple 18.5 VDC
to 30.2 VDC
X224
+
8.40 W
350 mA
1.1 A / 33 V
XF204
+
2.64 W
110 mA
1.1 A / 33 V
XF204-2
+
5.28 W
220 mA
1.1 A / 33 V
XF206-1
+
4.08 W
170 mA
1.1 A / 33 V
XF208
+
3.12 W
130 mA
1.1 A / 33 V
X200-4P IRT
+
9.6 W
400 mA
1.1 A / 33 V
X201-3P IRT
+
8.4 W
350 mA
1.1 A / 33 V
X201-3P IRT PRO
no redundancy
7.2 W
300 mA
1.1 A / 33 V
X202-2IRT
+
6.0 W
300 mA
600 mA / 60 V
X202-2P IRT
+
7.2 W
300 mA
1.1 A / 33 V
no redundancy
7.2 W
300 mA
1.1 A / 33 V
+
4.8 W
200 mA
600 mA / 60 V
no redundancy
4.8 W
200 mA
600 mA / 60 V
XF204IRT
+
4.8 W
200 mA
600 mA / 60 V
XF204-2BA IRT 1)
+
2.4 W
100 mA
2.5 A (non-replaceable
fuse F)
X202-2P IRT PRO
X204IRT
X204IRT PRO
1) With the specified power loss and current consumption these are the values of the basic
device without plugged in bus adapters. The values change depending on the port types of
the plugged in bus adapters. Per port you need to add the following values to the values of
the basic device:
Port type
Power loss
Current consumption
RJ-45
0.6 W
25 mA
SCRJ
1.8 W
75 mA
Examples
The following table shows the power loss an current consumption as an example for the
basic device with different bus adapters:
Type
Plugged in bus adapter
Port types
Power loss
Current consumption
XF204-2BA IRT
2 bus adapter BA 2×RJ-45
4 x RJ-45
4.8 W
200 mA
2 bus adapters BA 2xSCRJ
4 x SCRJ
9.6 W
400 mA
1 bus adapter BA 2xSCRJ
3 x SCRJ + 1 x RJ-45
8.4 W
350 mA
1 bus adapter BA SCRJ/RJ45
SCALANCE X-200
78
Operating Instructions, 12/2016, C79000-G8976-C284-09
Technical specifications
Optical data
Type
Transmitter output (optical)
Receiver input
min. [dBm]
max. [dBm]
Sensitivity min. [dBm]
Input power max. [dBm]
X204-2
X204-2TS
X204-2FM
X206-1
X212-2
XF204-2
XF206-1
X202-2IRT
-19
-14
-32
-3
X204-2LD
X204-2LD TS
X206-1LD
X212-2LD
-15
-8
-34
-3
X200-4P IRT
X201-3P IRT
X201-3P IRT PRO
X202-2P IRT
X202-2P IRT PRO
-8
-2
-23
+1
Type
Transmitter output (optical)
min. [dBm]
XF204-2BA
IRT
(with corresponding bus
adapters)
Receiver input
max. [dBm]
Sensitivity min. [dBm]
Input power max. [dBm]
POF cable
HCS cable
POF cable
HCS cable
POF cable
HCS cable
POF cable
HCS cable
-8
-19
-4.5
-11
-23
-26.8
+1
-4
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
79
Technical specifications
Permitted cable lengths - copper
For devices with degree of protection IP20/30
The following cables are permitted in the specified lengths:
● 0 to 55 m:
IE TP torsion cable with IE FC RJ-45 Plug 180
– Alternative:
0 to 45 m IE TP Torsion Cable + 10 m TP Cord via IE Outlet RJ-45
● 0 to 85 m:
IE FC TP marine / trailing / flexible / FRNC / festoon / food cable with IE FC RJ-45 Plug
180
– Alternative:
0 to 75 m IE FC TP marine / trailing / flexible / FRNC / festoon / food cable + 10 m TP
cord over IE FC outlet RJ-45
● 0 to 100 m:
IE FC TP standard cable with IE FC RJ-45 plug 180
– Alternative:
0 to 90 m IE FC TP standard cable + 10 m TP cord via IE FC outlet RJ-45
For devices with the "PRO" supplement (degree of protection IP65)
With these devices, splitting of the cables (as above) is not permitted. The following cables
are permitted in the specified lengths:
● 0 to 55 m:
IE TP torsion cable with IE FC RJ-45 Plug 180
● 0 to 85 m:
IE FC TP marine / trailing / flexible / FRNC / festoon / food cable with IE FC RJ-45 Plug
180
● 0 to 100 m:
IE FC TP standard cable with IE FC RJ-45 plug 180
SCALANCE X-200
80
Operating Instructions, 12/2016, C79000-G8976-C284-09
Technical specifications
For X208PRO (degree of protection IP65/67)
With the X208PRO, splitting of the cables (as above) is not permitted either. The following
cables are permitted in the specified lengths:
● 0 to 55 m:
IE TP torsion cable with IE FC M12 Plug PRO
● 0 to 85 m:
IE FC TP marine / trailing / flexible / FRNC / festoon / food cable with IE FC M12 Plug
PRO
● 0 to 100 m:
IE FC TP standard cable with IE FC M12 plug PRO
Permitted cable lengths - fiber-optic
Type
1 - 50 m
980/1000 plastic optical
fiber (POF)
1 - 100 m
200/230 polymer cladded
fiber (PCF)
0 - 4000
Glass FO cable
62.5/125 µm glass fibers
6 dB max. permitted cable 0 - 5000
attenuation with 3 dB link Glass FO cable
power margin
50/125 µm glass fibers
≤ 1 dB/km at 1300 nm;
0 - 26000 m
glass FO cable
9/125 µm single mode
fiber;
0.5 dB/km at 1310 nm;
13 dB max. permitted
cable attenuation with 2
dB link power margin
600 MHz x km;
6 dB max. permitted cable
attenuation with 3 dB link
power margin
X204-2
-
-
+
-
X204-2TS
-
-
+
-
X204-2FM
-
-
+
-
X204-2LD
-
-
-
+
X204-2LD TS
-
-
-
+
X206-1
-
-
+
-
X206-1LD
-
-
-
+
X212-2
-
-
+
-
X212-2LD
-
-
-
+
XF204-2
-
-
+
-
XF206-1
-
-
+
-
X200-4P IRT
+
+
-
-
X201-3P IRT
+
+
-
-
X201-3P IRT PRO
+
+
-
-
X202-2IRT
-
-
+
-
X202-2P IRT
+
+
-
-
X202-2P IRT PRO
+
+
-
-
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
81
Technical specifications
Degree of protection and MTBF
Type
Degree of protection
MTBF
X204-2
IP30
64 years
X204-2TS
IP20
63 years
X204-2FM
IP30
87 years
X204-2LD
IP30
60 years
X204-2LD TS
IP20
85 years
X206-1
IP30
72 years
X206-1LD
IP30
69 years
X208
IP30
83 years
X208PRO
IP65/67
83 years
X212-2
IP30
46 years
X212-2LD
IP30
43 years
X216
IP30
52 years
X224
IP30
45 years
XF204
IP20
48 years
XF204-2
IP20
60 years
XF206-1
IP20
69 years
XF208
IP20
54 years
X200-4P IRT
IP30
73 years
X201-3P IRT
IP30
78 years
X201-3P IRT PRO
IP65
85 years
X202-2IRT
IP30
62 years
X202-2P IRT
IP30
84 years
X202-2P IRT PRO
IP65
85 years
X204IRT
IP30
81 years
X204IRT PRO
IP65
99 years
XF204IRT
IP20
81 years
XF204-2BA IRT
IP20
78 years
Switching properties
Type
Max. number of learnable addresses
Aging time
Switching technique
Latency
X-200
8000
30 s
Store and forward
5 μs
XF-200
8000
30 s
Store and forward
5 μs
X-200IRT
4096
30 s (configurable)
Store and forward / cut through
< 5 μs
XF-200IRT
4096
30 s (configurable)
Store and forward / cut through
< 5 μs
SCALANCE X-200
82
Operating Instructions, 12/2016, C79000-G8976-C284-09
Technical specifications
Permitted ambient conditions
Note
Note the mounting position for XF and TS devices
With the following switches an ambient temperature of maximum +40 °C is permitted if the
device is installed on a vertical rail:
• XF204
• XF208
• XF204-2
• XF206-1
• XF204IRT
• X204-2TS
• X204-2LD TS
Type
Operating temperature
Storage/transport temperature
Rel. humidity in
operation (no condensation)
Operating altitude at max. xx
°C ambient temperature
X204-2
-40 °C to +60 ℃
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X204-2TS
-40 °C to +70 ℃ *)
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X204-2FM
-40 °C to +60 ℃
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X204-2LD
-40 °C to +60 ℃
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X204-2LD TS
-40 °C to +70 °C *)
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X206-1
-40 °C to +60 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X206-1LD
-40 °C to +60 ℃
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X208
-40 °C to +60 °C
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X208PRO
-40 ℃ to +70 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X212-2
-40 °C to +60 ℃
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X212-2LD
-40 °C to +60 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X216
-40 ℃ to +60 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X224
-40 ℃ to +60 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
XF204
-40 °C to +60 °C *)
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
XF204-2
-40 °C to +60 ℃ *)
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
XF206-1
-40 °C to +60 ℃ *)
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
83
Technical specifications
Type
Operating temperature
Storage/transport temperature
Rel. humidity in
operation (no condensation)
Operating altitude at max. xx
°C ambient temperature
XF208
-40 °C to +60 ℃ *)
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X200-4P IRT
-25 ℃ to +40 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 35 ℃
3000 m at max. 30 ℃
X201-3P IRT
-25 ℃ to +50 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 45 ℃
3000 m at max. 40 ℃
X201-3P IRT PRO
-25 ℃ to +60 ℃
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X202-2IRT
-40 °C to +60 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X202-2P IRT
-25 ℃ to +60 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X202-2P IRT PRO
-25 ℃ to +60 ℃
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X204IRT
-40 °C to +70 ℃
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
X204IRT PRO
-25 ℃ to +70 ℃
-40 ℃ to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
XF204IRT
-40 °C to +60 ℃ *)
-40 °C to +70 ℃
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
*) Note the information on the mounting position above.
Type
Plugged in bus adapter
Operating temperature
Storage/transport
temperature
Rel. humidity in
operation (no
condensation)
Operating altitude at max.
xx °C ambient temperature
XF204-2BA IRT
-
-20 °C to +60 °C
-40 °C to +85 °C
‹ 95 %
2000 m at max. 56 ℃
3000 m at max. 50 ℃
2 bus adapter BA 2×RJ-45 1)
0 °C to +60 °C
2000 m at max. 56 ℃
3000 m at max. 50 ℃
2 bus adapters BA 2×RJ-45
(coated) 1)
-20 °C to +60 °C
2000 m at max. 56 ℃
3000 m at max. 50 ℃
2 bus adapters BA 2xSCRJ
0 °C to +50 °C
2000 m at max. 45 ℃
3000 m at max. 40 ℃
2 bus adapters BA 2xSCRJ
(coated)
-20 °C to +50 °C
2000 m at max. 45 ℃
3000 m at max. 40 ℃
2 bus adapters BA
SCRJ/RJ45 1)
0 °C to +55 °C
2000 m at max. 50 ℃
3000 m at max. 45 ℃
1 bus adapter BA 2xSCRJ
0 °C to +50 °C
2000 m at max. 45 ℃
3000 m at max. 40 ℃
0 °C to +55 °C
2000 m at max. 50 ℃
3000 m at max. 45 ℃
0 °C to +50 °C
2000 m at max. 45 ℃
3000 m at max. 40 ℃
1 bus adapter BA
SCRJ/RJ45 1)
1 bus adapter BA 2×RJ-45 1)
1 bus adapter BA
SCRJ/RJ45 1)
1 bus adapter BA 2xSCRJ
1 bus adapter BA 2×RJ-45 1)
Bus adapters with FC interfaces have the same temperature values as bus adapters with
RJ-45 interfaces.
1)
SCALANCE X-200
84
Operating Instructions, 12/2016, C79000-G8976-C284-09
Technical specifications
Frame delay times
The number of IE Switches X-200 connected in a line influences the frame delay.
Note
Frame delay time with X-200 without IRT
When a frame passes through X-200 IE switches, it is delayed by the Store&Forward
function of the X-200 IE switches.
• With a 64 byte frame length by approx. 10 microseconds (at 100 Mbps).
• With a 1500 byte frame length by approx. 130 microseconds (at 100 Mbps).
This means that the more X-200 IE switches the frame passes through, the longer the frame
delay.
Note
Frame delay time with X-200 with IRT
The more X-200IRT IE switches a frame runs through, the higher the frame delay. By using
the "cut through" switching mechanism, the X-200IRT IE switches are ideal to meet the realtime requirements of PROFINET.
Cut through is, however, not possible:
• Between a port set to 10 Mbps and a port set to 100 Mbps.
• When two packets are to be sent at the same time on one port.
In this case, an X-200 IE switch changes to Store&Forward and the delay increases.
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
85
Technical specifications
SCALANCE X-200
86
Operating Instructions, 12/2016, C79000-G8976-C284-09
Dimension drawings
Figure A-1
A
Drilling pattern SCALANCE X204-2, X204-2TS, X204-2FM, X204-2LD, X204-2LD TS,
X206-1, X206-1LD, X208, X200-4P IRT, X201-3P IRT, X202-2IRT, X202-2P IRT,
X204IRT
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
87
Dimension drawings
Figure A-2
Drilling pattern SCALANCE X212-2, X212-2LD and X216
SCALANCE X-200
88
Operating Instructions, 12/2016, C79000-G8976-C284-09
Dimension drawings
Figure A-3
Drilling pattern SCALANCE X224
Figure A-4
Side view SCALANCE X-200
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
89
Dimension drawings
Figure A-5
Side view SCALANCE X-200 POF with POF interface
Figure A-6
Dimension drawings of the SCALANCE X208PRO, SCALANCE X201-3P IRT PRO,
SCALANCE X202-2P IRT PRO and SCALANCE X204IRT PRO
SCALANCE X-200
90
Operating Instructions, 12/2016, C79000-G8976-C284-09
Dimension drawings
Figure A-7
Drilling pattern of the SCALANCE X208PRO, SCALANCE X201-3P IRT PRO,
SCALANCE X202-2P IRT PRO and SCALANCE X204IRT PRO
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
91
Dimension drawings
Figure A-8
SCALANCE XF-200 dimension drawings
Figure A-9
Dimension drawing SCALANCE XF204-2BA IRT
SCALANCE X-200
92
Operating Instructions, 12/2016, C79000-G8976-C284-09
B
Test of mechanical stability
Mechanical stability
Device type
SCALANCE
IEC 60068-2-6 vibration
IEC 60068-2-27 shock
X204-2
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
X204-2TS
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
X204-2FM
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
X204-2LD
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 11 ms duration
6 shocks per axis
X204-2LD TS
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
X206-1
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
X206-1 LD
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
X208
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
X208PRO
5 - 9 Hz 3.5 mm
9 - 150 Hz 1 g
10 cycles
15 g, 11 ms duration
6 shocks/axis
X212-2
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 11 ms duration
6 shocks per axis
X212-2LD
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
X216
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 11 ms duration
6 shocks per axis
X224
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 11 ms duration
6 shocks per axis
XF204
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
XF204-2
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
5 – 150 Hz: Max. 7.9
g
random
5 – 150 Hz: Max. 7.9
g
random
15 g, 6 ms duration
6 shocks per axis
15 g, 6 ms duration
6 shocks per axis
50 g, 30 ms duration
6 shocks per axis
50 g, 30 ms duration
6 shocks per axis
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
93
Test of mechanical stability
Device type
SCALANCE
IEC 60068-2-6 vibration
IEC 60068-2-27 shock
XF206-1
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
XF208
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 6 ms duration
6 shocks per axis
X200-4P IRT
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 11 ms duration
6 shocks per axis
X201-3P IRT
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 11 ms duration
6 shocks per axis
X201-3P IRT PRO
5 – 9 Hz: 3.5 mm
9 – 150 Hz: 1 g
10 cycles per axis
15 g, 11 ms duration
6 shocks per axis
X202-2IRT
10 - 58 Hz: 0.075 mm
58 - 500 Hz: 1 g
10 cycles per axis
10 g, 16 ms duration
6 shocks per axis
X202-2P IRT
5 – 9 Hz: 3.5 mm
9 – 500 Hz: 1 g
1 octave/min, 20 sweeps
15 g, 11 ms duration
6 shocks per axis
X202-2P IRT PRO
5 – 9 Hz: 3.5 mm
9 – 150 Hz: 1 g
10 cycles per axis
15 g, 11 ms duration
6 shocks per axis
X204IRT
10 - 58 Hz: 0.075 mm
58 - 500 Hz: 1 g
10 cycles per axis
10 g, 16 ms duration
6 shocks per axis
X204IRT PRO
5 – 9 Hz: 3.5 mm
9 – 150 Hz: 1 g
10 cycles per axis
15 g, 11 ms duration
6 shocks per axis
XF204IRT
10 - 58 Hz: 0.075 mm
58 - 500 Hz: 1 g
10 cycles per axis
10 g, 16 ms duration
6 shocks per axis
XF204-2BA IRT
10 - 58 Hz: 0.075 mm
58 - 500 Hz: 1 g
10 cycles per axis
10 g, 16 ms duration
6 shocks per axis
Note
The interfaces of the X-200 IE switches can be divided into groups each with 4 ports:
• P1 to P4
• P5 to P8
• P9 to P12
• etc.
If only ports of different port groups are used, the device meets the requirements for
Environment B in compliance with IEEE 802.3, Section 33.4.1.1. If ports of the same port
group are used, the requirements for Environment A are met.
SCALANCE X-200
94
Operating Instructions, 12/2016, C79000-G8976-C284-09
Training, Service & Support
C
Industry Online Support
In addition to the product documentation, the comprehensive online information platform of
Siemens Industry Online Support at the following Internet address:
(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=
en)
Apart from news, there you will also find:
● Project information: Manuals, FAQs, downloads, application examples etc.
● Contacts, Technical Forum
● The option submitting a support query:
(https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid
=38718979&caller=view)
● Our service offer:
Right across our products and systems, we provide numerous services that support you
in every phase of the life of your machine or system - from planning and implementation
to commissioning, through to maintenance and modernization.
You will find contact data on the Internet at the following address:
(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en)
SITRAIN - Training for Industry
The training offer includes more than 300 courses on basic topics, extended knowledge and
special knowledge as well as advanced training for individual sectors - available at more
than 130 locations. Courses can also be organized individually and held locally at your
location.
You will find detailed information on the training curriculum and how to contact our customer
consultants at the following Internet address:
(www.siemens.com/sitrain)
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
95
Training, Service & Support
SCALANCE X-200
96
Operating Instructions, 12/2016, C79000-G8976-C284-09
Index
Number of connectors, 15
A
Article number
C-PLUG, 20, 20
Power Plug PRO, 52
Redundancy module, 20
RJ-45 data plug-in connector, 20
SC RJ plug-in connector, 21
Auto polarity exchange, 60
Autonegotiation, 60, 60
O
Operating instructions, 4
Order number
C-PLUG, 30
Overview of the functions, 15
P
Bus adapter, 21
Polarity reversal, 60
Power llimiter, 20, 47
Power Plug PRO
Article number, 52
C
R
Components of the product, 3
Configuration Manual, 4
Redundancy module, 47
Reference identification label, 22
E
S
ESD directives, 34
Extension module, 20, 47
Safety notices
Use in hazardous areas, 47
when connecting up, 47
Selection Tool, 7
SET button, 28
SIMATIC NET glossary, 9
SIMATIC NET Selection Tool, 7
Support, 95
System manual, 7, 67
B
F
Factory settings, 28
Frame delay times, 14
Function, 13
G
GI-PCF, 65
Glossary, 9
T
Training, 95
M
MDI / MDI-X autocrossover, 60, 61
N
Node localization, 27
SCALANCE X-200
Operating Instructions, 12/2016, C79000-G8976-C284-09
97
Index
SCALANCE X-200
98
Operating Instructions, 12/2016, C79000-G8976-C284-09
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement