Lenco SCD-24 CD radio Instruction manual

Below you will find brief information for CD radio SCD-24. The Lenco SCD-24 is a compact CD radio with a built-in FM receiver. It can play both CDs and radio stations. You can adjust the volume and tune to your favorite radio station using the rotary knobs. The SCD-24 also has a built-in telescopic antenna for better FM reception. You can also use headphones for private listening.

PDF Download

Document

STEREO FM RADIO WITH CD PLAYER
SCD-24
INSTRUCTION MANUAL
For information and support, www.lenco.com
WARNING
CLASS 1 LASER PRODUCT
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
CLASS 1 LASER PRODUCT
APPAREIL &Aacute; LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
This product contains a low power laser device.
Warning: Do not touch the lens.
DO NOT THROW BATTERIES IN FIRE !
PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty, or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by
placing it on a carpet.
ON SAFETY
• When connecting and disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC power cord.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety.
ON AC VOLTAGE
• Before use, check that the rated voltage of your unit matches your local voltage.
ON CONDENSATION
• When left in a heated room where it is warm and damp,water droplets or condensation may form inside the CD player.
• When there is condensation inside the unit, the unit may not function normally.
• Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.
* Ensure a minimum distance of 5 cm around the apparatus for sufficient ventilation.
* Ensure that the ventilation is not impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc..
* Do not place naked flame sources, such as lighted candles on the apparatus.
* Take attention to the environmental aspects of battery disposal.
* Use the apparatus only in moderate climates (not in tropical climates).
* Do not expose the apparatus to dripping or splashing.
* Do not place objects filled with liquids, such as vases, on the apparatus.
Should any trouble occur, disconnect the AC power cord and refer servicing to qualified personnel.
“To be completely disconnect the power input, the mains plug of apparatus shall be disconnected from the mains.” as the
disconnect devices is the mains plug of apparatus.
“The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use.”
“Excessive sound pressure from earphones and headphones can cause hearing loss.”
“Battery shall not be exposed to excessive heat such as sunshine, fire or the like.”
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightening flash
with arrowhead symbol
within the triangle is a
warning sign alerting
the user of &quot;dangerous
voltage&quot; inside the unit.
ATTENTION : To reduce the risk
of electric shock, do not remove the
cover. There are no user serviceable
parts inside the unit. Refer all servicing
to qualified personnel.
The exclamation point within
the triangle is a warning sign
alerting the user of important
instructions accompanying
the product.
In case of malfunction due to electrostatic discharge, the apparatus has to be reset by disconnecting it from mains supply.
THE MARKING PLATE IS LOCATED AT THE BACK OF ENCLOSURE OF THE APPARATUS
LOCATION OF CONTROLS
8
7
6
4
3
6
9
5
10
11
2
1
13
12
14
15
16
17
18
19
20
21
22
23
1. CD PROGRAM BUTTON
2. CD REPEAT BUTTON
3. BBS BUTTON
4. POWER INDICATOR
5. CD DISPLAY 6.SPEAKER
7. CD DOOR
8.
TELESCOPIC ANTENNA
9. OPEN / CLOSE CD BUTTON
10. FM STEREO INDICATOR
11. CD NEXT BUTTON
12.
13.
14.
15. 16. 17.
18.
19.
20.
21.
22.
23.
GB 1
CD PLAY / PAUSE BUTTON
CD BACK BUTTON
CD STOP BUTTON
DIAL SCALE
MODE SWITCH
TUNING CONTROL
AC SOCKET
CARRYING HANDLE
VOLUME CONTROL
FUNCTION SWITCH
PHONES JACK
BATTERY COMPARTMENT
POWER SUPPLY
USING HOUSE CURRENT
Before use, check that the rated voltage of your unit matches
your local voltage.
Note: plug is used as the disconnect device.
the disconnect device shall remain readily operable.
To AC socket
USING BATTERIES
Disconnect the AC power cord from the AC inlet of the
unit. Battery power is cut automatically by the cord while
it is connected.
To AC outlet
When the volume decrease, or the sound distorts, replace
all of the batteries with new ones.
_
+
_
+
_
+
Insert 6 UM-2
( size C ) batteries.
battery door
ADJUSTING THE SOUND
TO ADJUST THE VOLUME
VOLUME
MAX.
FOR PRIVATE LISTENING
Plug in headphones (&oslash;3.5 mm stereo mini-plug) to the
PHONES jack.
When headphones are plugged in, the speakers are
automatically disconnected.
MIN.
VOLUME
LISTENING TO THE RADIO
2 . Select a MODE.
1 . Set to RADIO
FUNCTION
MODE
FM MONO
RADIO
FM ST.
4 . Adjust the sound.
3 . Tune in to a station.
VOLUME
TUNING
MAX.
MIN.
VOLUME
GB 2
FOR BETTER RECEPTION
FM
NOTE : 1. FM stereo LED indicator lights if receive FM stereo broardcast and the MODE switch set on &quot;FM STEREO&quot;.
2. When too much noise is heard during FM STEREO reception, set MODE switch to FM mono.
AFTER LISTENING
Set the FUNCTION selector to OFF.
COMPACT DISC PLAYBACK
1 . Set to CD
3. Insert a disc with the label side facing up.
FUNCTION
4 .
CD
2 . Open the CD door by pushing
CD Door Open / Close button.
Close the CD door.
The disc will rotate and the total
tracks of the disc will show on
the display.
5. Press the Play / Pause button.
Track number &quot; 01 &quot; &amp; &quot; PLAY
&quot; will
be shown.
PLAY
CD display
TO INTERRUPT PLAYBACK
Press the Play/Pause button and the symbol
&quot; PLAY &quot; will be flashed.
Press the button again to resume playback.
TO STOP PLAYBACK
Press the STOP button and the display shows the total
tracks of the disc.
PLAY
CD display
TO SKIP TO THE BEGINNING OF A TRACK
•
Press either one of the skip buttons according to the desired skip direction.
•
Play/back resumes from the selected track.
•
When the button is pressed once during play, the previous track starts again.
•
When the button is pressed once during play, the next track plays.
SEARCHING FOR A PASSAGE WITHIN A TRACK
•
Keep the or button pressed during playback,
and release the button as soon as you recognise the desired
passage. Then normal CD playback will resume from this point.
Unit will be automatically off at about 15 mins without any operation (in stop mode / CD door open).
After auto off, slide the FUNCTION selector to OFF position and then slide to RADIO / CD position for listening. GB 3
REPEAT PLAYBACK
This function allows a single track or all tracks on a disc to be played repeatedly.
TO REPEAT THE SAME TRACK
Press the REPEAT button once
during playback, the CD display
will indicate &quot; REPEAT &quot;.
TO REPEAT THE WHOLE DISC
Press the REPEAT button twice
until &quot; REPEAT ALL&quot; displays.
REPEAT
PLAY
REPEAT
PLAY
ALL
TO CANCEL REPEAT PLAYBACK FUNCTION
Press the REPEAT button again until &quot; REPEAT &quot; or
&quot; REPEAT ALL &quot; disappears from the display.
Note on CD-R/RW discs
- Because of non-standardized format definition/ production of CD-R/RW, playback quality and performance are not guaranteed.
- Manufacturer is not responsible for the playability of CD-R/RW due to recording conditions, such as PC performance, writing software, media ability, etc.
- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a malfunction.
- It is recommended to record only audio files on CD-R/RW discs for easy reading.
BASS BOOST
To enjoy a BASS BOOST sound effect,
press BBS button.
PROGRAM PLAYBACK
PROGRAMMED PLAYBACK
Programmed playback enables tracks on a disc to be played
in the desired order. Up to 20 tracks can be programmed.
1. Press the &quot; PROGRAM &quot; button.
2. Press the &quot; NEXT &quot; and &quot; BACK &quot; buttons
to select the desired track number.
3. Press &quot; PROGRAM &quot; button again to memorize the track.
4. Repeat steps 2 and 3 until all desired tracks are
programmed.
5. Press the &quot; PLAY/PAUSE &quot; button to start.
&quot; PLAY
&quot; , &quot; PROGRAM &quot; &amp; track number are shown on the CD display.
6. Press &quot; STOP &quot; button to stop programmed
playback.
7.
Press &quot; PLAY/PAUSE &quot; buttons to resume programmed
playback.
Open the CD door, turn off the CD player or press “ STOP ” button twice to clear the programmed memory.
Note : Programming can only be made when the player is in stop mode.
8.
&quot; PROGRAM &quot;
CD display
GB 4
MAINTENANCE
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly
wiping with a soft cloth.
CLEANING A CD
If the CD skips or will not play , the disc may need cleaning
. Before playing, wipe the disc from the centre out with a
cleaning cloth. After playing, store the disc in its case.
IMPORTANT NOTE
If an abnormal display indication or an operating problem
occurs, disconnect the AC power cord and remove the
batteries. Wait at least 5 seconds, then reconnect the AC
power cord or reinstall the batteries.
WARNING
Should the CD door be opened before the reading of the CD
is completed, a jamming noise may occur. This is resolved
by closing the CD door.
CLEANING THE CD LENS
If the CD lens is dusty, clean it with a brush-blower. Blow
several times on the lens and remove the dust with the
brush. Finger prints may be removed with a cotton swab
moistened with alcohol.
SPECIFICATIONS
CD SECTION
Channels:
S / N ratio:
Wow &amp; Flutter: Sampling frequency:
Quantization:
Pick up light source: Pick up wave length
2 channels
60 dB
undetectable
44.1 kHz 8 x over sampling
1 bit DA converter
Semi - conductor laser
790 nm
RADIO SECTION
Tuning ranges:
Antennas:
FM 87.5 - 108 MHz
FM Rod antenna
GENERAL
Output power:
1 W + 1 W (RMS)
Power consumption:
13.5 W
Speaker: 3 &quot; 8 OHM
Phones jack:
3.5MM
Power source: AC : 230V ~ 50Hz
DC : 9V ( 6 x 1.5V LR14/ &quot;C&quot;/UM2 )
Dimensions:
224(L) x 234(D) x 126(H)mm
Weight
1.45 KGS
Due to continuing improvement, the features and the design are subject to change without notice.
GB 5
Guarantee
Lenco offers service and warranty in accordance with the European law, which means that in case of repairs (both during
and after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer
will be voided.
Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications
and pictures in this documentation may differ slightly from your particular situation. All items described in this guide for
illustration purposes only and may not apply to particular situation. No legal right or entitlements may be obtained from the
description made in this manual.
Disposal of the Old Device
This symbol indicates that the relevant electrical product or battery should not be disposed of as general
household waste in Europe. To ensure the correct waste treatment of the product and battery, please
dispose them in accordance to any applicable local laws of requirement for disposal of electrical
equipment or batteries. In so doing, you will help to conserve natural resources and improve standards
of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic
Equipment Directive).
WARNING: Prolonged exposure to loud sounds from personal music players may lead to temporary or
permanent hearing loss.
Where to place the item :
Today’s furniture is coated with a wide variety of lacquers and synthetic-coatings that are treated with an extensive range
of cleaning products. Therefore, the possibility that some of these substances contain components that react adversely to
the rubber feet of the item and soften them, cannot be completely excluded. The rubber feet of the appliance can cause
discoloring to furniture surfaces. If necessary, place the appliance on a non-slide surface.
&reg;All rights reserved
Service
For more information and helpdesk support, please visit www.lenco.com
Lenco Benelux BV, Thermiekstraat 1a, 6361 HB, Nuth, The Netherlands
GB 6
">

Hello! I am an AI chatbot specifically trained to assist you with the Lenco SCD-24 CD radio Instruction manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key Features

CD playback
FM radio receiver
Telescopic antenna
Headphone jack
Volume control
Bass boost
Programmable playback

Frequently asked questions

How do I clean the CD lens?

If the CD lens is dusty, clean it with a brush-blower. Blow several times on the lens and remove the dust with the brush. Finger prints may be removed with a cotton swab moistened with alcohol.

What are the power sources for this radio?

The radio can be powered by AC power or by 6 UM-2 (size C) batteries.

What sizes headphones can I use with this radio?

You can use headphones with a ø3.5 mm stereo mini-plug.

How do I program a sequence of tracks on a CD?

You can program up to 20 tracks. Press the "PROGRAM" button, select the track number, press "PROGRAM" again to memorize. Repeat until all desired tracks are programmed. Press "PLAY/PAUSE" to start.