Antenna Selection and Positioning Guide

Antenna Selection and Positioning Guide
The dos and don’ts of antenna selection and placement
Table of Contents
Antennas 101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Selecting Antenna Types . . . . . . . . . . . . . . . . . . . . . . 4
External Antenna Considerations . . . . . . . . . . . . . . . . 8
Antenna Placement Best Practices . . . . . . . . . . . . . . .10
Coverage vs Capacity . . . . . . . . . . . . . . . . . . . . . . . . .16
Site Surveys and RF Planning . . . . . . . . . . . . . . . . . . .16
Continuous Performance Monitoring . . . . . . . . . . . . . 17
Images Attribution
Front cover: © Benedikt Weishaupt
Bad placement examples courtesy of:
After all the effort invested in selecting a WLAN vendor and planning an Enterprise wireless
LAN, many customers underestimate the importance of antenna selection and careful
placement, and end up settling for lower performance than they were expecting.
The purpose of this guide is to give you a straightforward and not overly technical overview of
antenna design, to provide guidance on choosing the right antenna and maximizing coverage and
capacity, and to identify common antenna deployment mistakes to be avoided.
Throughout the guide, references to performance and coverage are primarily targeted toward
802.11n deployments, which are the majority use case today. Exceptions accounting for
802.11ac will be identified.
Antennas 101
The world of antennas is rife with technical jargon for a range of related features that together
result in a wireless signal with a certain range and radiation profile. It can be quite difficult to
grasp how the various factors interplay. So let’s quickly review how an antenna system works.
How antennas work
Whether it is for Wi-Fi or 4G or another wireless technology, an antenna is basically an extension
of a wireless radio. The principles are the same for all wireless systems. The range of an
antenna is the result of several factors. The first of which is the amount of energy entering
the system, which is known as the radio transmit power (Tx). As the radio energy passes
through connectors and cables to the antenna, some of it is lost. This is known as cable loss.
Finally the remaining energy is concentrated in a certain radiation pattern, depending on the
design and polarity of the antenna. Different antenna materials and design features result in
different antenna gain. The gain of the antenna defines how concentrated the energy is – Thus
the combination of Tx power, cable loss and antenna gain, define the antenna’s range. The
radiation pattern, that is the 3D shape of the radio waves propagating from the antenna, also
varies according to the type of antenna.
4 more important concepts
Decibels: RF is measured in decibels (dB) which are on a logarithmic scale, just like
earthquakes or sound which can be almost imperceptible or ear splittingly loud, tens of
thousands of times louder than “almost imperceptible”, yet the human ear can cope with both
ends of that continuum. Because of the logarithmic scale, every 3 dB increase represents a
doubling of power.
Absolute power levels are often represented in dBm. Where 0 dBm equals 1 mW. Use of
decibels makes a lot of sense when handling large power level differences. Typical access
point maximum output power of 20 dBm translates to 0.1 Watts RF power, while the cell edge
limit is typically around -67dBm which equates to 0.0000000002 Watts.
Polarization: Refers to the orientation of the
radiating element of an antenna. The simplest
vertically mounted dipole or “rubber duck”
antenna is said to be vertically polarized and
generally has a circular radiation pattern
(omnidirectional) in the horizontal plane.
Antennas are typically either vertically polarized
or horizontally polarized, or they may have both
element orientations in dual polarization antennas.
Fig 1. Radiation pattern in the horizontal plane
In an ideal world you would want the
transmitting and receiving antennas to have
the same polarization. In fact for point-topoint radio connections this is critical. However, due to reflections in typical wireless network
environments, polarization may vary continuously and the antennas in mobile devices are
designed to work with any polarity, since they can be held at any angle. Polarization is less
important than antenna gain pattern in typical Wi-Fi networks.
Antenna Gain: It is a common misunderstanding that antenna gain is amplification of the
signal, and it might seem like that is what it is. But really, it is a measure of how concentrated or
strong the signal is in the direction of its maximum signal. Increasing the signal concentration
in one plane generally reduces it in another plane. This will become clearer when you read
about omnidirectional antenna gain below. Antenna gain is represented as dBi, which stands
for dB gain relative to an isotropic radiator which has a perfectly circular pattern.
Total antenna gain includes also another less known component, namely efficiency. An
antenna may possess certain directional characteristics, but it might still attenuate the
signal from the main lobe direction. This is most typical for small integrated antennas where
compromises have to be made between size, performance and cost.
Attenuation: When an RF signal travels through a medium, say a brick wall, a door, or
a cubicle partition, it is attenuated to some degree. That means the power of the signal
diminishes. Say the input signal on one side of a wall is 10 milliwatts but it is only 5 milliwatts
on the other side, this represents 3 dB of attenuation. Remember the dB log scale and the 3
dB rule noted earlier.
Selecting Antenna Types
Omnidirectional Antennas
Omnidirectional antennas are the most common type you find on Enterprise access points
(APs) for indoor use. They are designed to provide general coverage in all directions in the
horizontal plane. For indoor APs this is an obvious default, as it is unknown where the AP will
be placed, most likely it will be in the middle of an indoor area and not its perimeter.
Many vendors integrate the antenna within the access point housing to prevent tampering, and
improve aesthetics, but this means the AP must be mounted in the correct plane.
DON’T mount APs with integrated antennas vertically, they must be mounted horizontally.
If you mount a dipole antenna with a horizontal
donut shaped gain pattern in a vertical orientation,
most of the antenna gain now radiates vertically
to floors both above and below. Too much signal
going to the adjacent floors increases interference
on those floors, while clients on the floor the
antenna is on get hardly any signal at all.
With the evolution to 802.11ac, because there are
more antennas involved, we are seeing a reversal
of the integrated antenna trend, back to “paddle”
antennas. After years of sleek AP designs, it is a
pretty jarring twist, despite the increased mounting
Fig 2. AP “mounted” in wrong orientation
Extending coverage with external antennas
Integrated omnidirectional antennas generally offer low gain in the 2.5 – 5 dBi range while
the AP radios offer a maximum transmit power in the 16 – 20 dBm range. Together this gives
them a radius of 100-300 meters in open space and 10-30 meters (30-100 ft.) in most office
environments depending on building construction and internal furnishings. This makes typical
integrated antennas ideal for most office deployments, where access points and client devices
are generally rather close to each other, since the main priority is not coverage but capacity
(see section on Coverage vs Capacity).
Integrated antennas are not as suitable for large spaces such as warehouses and distribution
centers with relatively low user densities, low bandwidth application requirements, and very
high ceilings. Here you need external directional antennas with higher gain. These come in a
variety of shapes and sizes making them more or less suitable for different applications:
Dipole antenna or Dipole array
Ceiling blister / dome antenna
Fig 3. Different external high-gain omnidirectional or hemispherical antennas
Dipole or Dipole array: An external dipole antenna is a tubular antenna usually enclosed in a
fiberglass casing that looks like a light saber, except it doesn’t glow or hum. Essentially this is the
same type of technology found in paddle antennas fitted to an AP, only externalized. Sometimes
two or more dipoles are placed one above the other to increase gain and narrow down the
vertical beam width. The only visual difference is the tube length.
Ceiling blister or Dome antenna: This is not substantially different from mounting an access
point with an integrated antenna directly on the ceiling, except they are more attractive, less
conspicuous, and easily mistaken for security cameras, or smoke detectors. Plus you can
choose an antenna with slightly higher gain than those on the AP.
Directional Antennas
Although directional antennas are mostly used for long range point-to-point and point-tomultipoint connections for bridging and mesh, they also have applications for indoor and
outdoor client access.
Client Access
In a warehouse for example, instead of using an omnidirectional antenna in the middle of the
building, you could use sector and panel antennas around its perimeter: panel antennas on
the sides and narrower sector antennas in the corners facing inward. Long hallways represent
an ideal use case for panel antennas too. Similarly, for outdoor areas such as courtyards, the
same principals apply.
Wall-mounted panel
Discrete recessed panel
Ceiling patch
Corner mounted sector
Fig 4. Different external high-gain directional antenna formats
Another common use for panel and sector antennas is in buildings with high ceilings and
locations such as auditoriums where you have an equally high density of users at the edge
of the room as you do in the middle. Also, many hotels, museums and other venues are
concerned about building aesthetics and prefer to use discretely mounted panel antennas on
walls rather than having ceiling mounted objects.
Patch antenna: A patch antenna is a wafer-like antenna which comprises two metallic plates,
one larger than the other, with a dielectric sheet in the middle. They are suitable for a singlefloor of small offices or a store and produce hemispherical coverage, with a 30°-180° spread
from the mount point. Because they are flat, thin and lightweight they make for inconspicuous
mounting on ceilings.
Panel antennas: These are designed to be mounted flat on a wall or other vertical surface,
and to radiate all their energy directionally away from the wall. Most of the radiation is to the
front and a little to the sides. They usually have gain greater than 8 dBi. Panel antenna are
usually implemented by grouping several patch antennas with carefully defined gaps between
them. An example would be having 4 patch elements in a symmetric 2x2 configuration
producing an hemispherical pattern. There is very little vertical radiation, so they are only
suitable for serving one floor at a time, such as a long room or hallway.
A well shielded panel has a minimal rear lobe, which allows you to place two panel antennas
back to back either side of a wall, each radiating signal only into its respective area.
Sector antennas: Sector antennas come with a variety of beam widths such 45°, 90° and 120°
or anything in between. They come in various form factors such as a corner radiator, a dish
or panel with an asymmetric 1x4 element configuration, and can be used indoors or outdoors
wherever there is a need for coverage in a well specified area, or if it is important to prevent
signal bleeding into another area. They usually have gain in the 10 dBi to 15 dBi range.
Parabolic grid antennas: These are highly directional and have a very high gain. They usually
comprise a dipole element in the middle which generates the energy. Then the parabolic
reflector focuses the energy in a narrow beam, much like a focused flashlight. They are used in
long-range outdoor point-to-point connections. A parabolic antenna with 15-30 dBi can reach
up to 12.5 Km (7.8 miles). Grid antennas have superior wind tolerance to a solid dish, which
allows for placement in windy areas, a larger size and higher gain.
Yagi antennas: In contrast to parabolic antennas, Yagi-Uda (or Yagi for short) antennas look
like a fishbone, when not encased in a protective enclosure, and comprise a series of rods
perpendicular to a main rod which is pointed in the target direction. These are also used for
point-to-point and point-to-multipoint connections but for shorter distances, and usually have
a gain of 9-5 dBi. They are very light, easily mounted on a pole, and because of a wider beam
width, are easier to align than parabolic dish antennas.
Parabolic Grid
Fig 5. High-gain outdoor antennas for point-to-point connections
External Antenna Considerations
Once you opt for using external antennas, everything gets a bit more interesting.
Antenna Gain trumps Tx power
In general, to increase coverage, it is best to improve antenna gain, not crank up the transmit power.
DON’T just crank up transmit power to increase range, use antennas with higher gain.
The reason for this is that increasing the transmit power on the AP does nothing for receive
sensitivity. Whereas increasing Antenna dBi improves both transmit and receive. In fact, a
law of reciprocity applies. Basically Tx and Rx gain are the same. The job of the antenna is to
transmit from the AP and receive from the client. Clients rarely have a problem hearing the AP,
but they have comparatively feeble radios (less power) and low gain antennas, so they have
a problem being heard by the AP. An antenna with higher dBi is better able to hear low power
laptops and even lower powered transmissions from mobile devices, at longer distances.
Switching from an integrated 3 dBi antenna to an external antenna with 9 dBi, which is a
jump of 6 dB, would quadruple the power, resulting in double the cell radius in open space.
Also, unlike increasing transmit power alone, it is less likely to result in asymmetric data rates
between clients and APs.
DO remember the 3 dB rule. Each 3 dBi increase in antenna gain doubles its power.
Antenna gain
Wireless range
Fig 6. Antenna gain and wireless range in unobstructed air
Going too far with high gain antennas
Imagine the radiation pattern of an omnidirectional antenna as being like a donut with the
antenna sticking up through the center, as shown in Fig 1. In the horizontal plane (the Azimuth)
it has a diameter, which is its range, but it also has a vertical dimension (the Elevation). As the
antenna’s dBi increases, the diameter increases, giving you greater range sideways, but the
vertical dimension shrinks becoming less like a donut, and more like a CD disk, resulting in a
smaller vertical target area in which clients are able to receive a signal. Therefore the height at
which a high-gain omnidirectional antenna is positioned becomes more important.
DO carefully review antenna gain charts and follow the manufacturer’s height
recommendations when using high gain antennas, vertical positioning is critical.
DON’T place high-gain dipole antennas on ceilings in large open spaces. In the
absence of reflections, most antenna gain points to other APs, not client devices.
Choosing external antennas for each band
A lot of high-gain external antennas are optimized for 2.4 GHz or 5 GHz and do not support
both bands. That means you may need two or three antennas for each radio, depending on
the MIMO configuration. Dual band antennas are available and in most cases, especially for
indoor use, they are the better choice. However, since enterprises generally need more 5 GHz
cells than 2.4 GHz, single band antennas can make sense in a few locations. Some special
venues, like stadiums and outdoor deployments may be an exception where it makes sense to
use single band APs or antennas.
Bear in mind that usually both radios are active in all or most of your APs, so choosing single
band antennas carries a risk if your needs change, whereas a dual band capability allows
more reconfiguration flexibility.
DON’T assume external antennas are dual band. Most are optimized for a single band.
There are three reasons for having more 5 GHz cells. The first is that 5 GHz attenuates more
rapidly and therefore has less range than 2.4 GHz. The second is that with more channels
available, it is possible to have much higher cell density without using overlapping channels.
Finally by utilizing its 40 MHz channel bonding capabilities 5 GHz can provide superior
throughput, and the same goes for 802.11ac with its 40 MHz bonding, or 80 MHz bonding in
some specific environmental deployments. In 2014 the FCC freed up an additional 100 MHz in
the 5 GHz spectrum, which will be a great boon for those migrating to 802.11ac and wishing to
exploit 80 MHz bonding in the future.
DO focus on 5 GHz as your performance channel, and 2.4 GHz for coverage.
Minimizing cable length and connectors
The 50 Ohm coaxial cable needed to connect the antenna to your AP has inherent attenuation
(signal loss), and there are several different grades of cable. The longer the cable, the more
important it is to select high grade low-loss cable.
Fig 7: Cable loss rates for different grades of coaxial cable
In addition, in many of the APs which have integrated antennas and also provide connectors
for external antennas, there is often an RF interconnect attenuation, sometimes as much as 1
dB, between the radios and the connectors.
When using external antennas, keep the cable length as short as possible. It is really important
to use high grade cables with the right impedance, the right length, and the right connectors
(to avoid extra adapter transitions). Right length means no longer than necessary, and
definitely not shorter. Joining multiple cables is a gain-killer as it adds more connectors. See
this example of gain loss.
Fig 8. Calculating total signal loss for an antenna cable
100 ft. cable
5 ft. cable
DON’T use cables any longer than necessary, or join short cables together.
Total Signal Loss Calculation
Connectors (4) = -2.0 dB
Lightning Arrestor = -1.0 dB
Cable (105 ft) = -4.095 dB
Total = -7.095 dB
DON’T use cheap cables for long runs, you’ll waste a lot of signal strength in cable loss.
Next check the connectors. There are a variety of different types and vendors vary them from
one product to the next. Often you need different connectors at each end of the cable. So be
particularly careful making sure the connector at each end of the cable matches the antenna
or AP you will attach it to.
DON’T forget to double check cable connectors will match the AP and antenna.
Antenna Placement Best Practices
If you designed your Wi-Fi network for the ultimate performance, you would have thousands of
tiny cells each serving a few hundred square feet, with antennas really close to the users. But
that is a 20x budget daydream.
In the real world, you always make tradeoffs and accept compromises. However, some
placement compromises are more costly to performance than others, so think carefully when
deciding where to mount each AP and antenna.
Separate from the obvious mounting locations predicated by the type of AP or antenna you
are using: ceiling, wall, corner, pole etc. there are a number of other environmental conditions
related to the mounting point and the type of antenna, to consider. Ignoring these is the cause
of many of the most common placement errors.
In the following section, the term antenna is used to refer to both external antennas and APs.
Aesthetics over function
There are many venues where aesthetics will prevail over function. But it is important that you
let your peers know that certain aesthetic choices often have tradeoffs. It doesn’t have to be
all or nothing, if those obsessed with aesthetics had a better understanding of the real cost of
matching the optimal performance of a non-aesthetic design, they may not be so adamant, or
may be more willing to compromise.
DON’T give way to aesthetics without recognizing the performance trade-offs.
Typical ceiling mounting
In office environments the optimum mounting height is 8-12 ft off the ground. Most vendors
assume that their APs will be mounted on the ceiling which is usually about 10 ft high. Some
even have a slight down-tilt of the integrated antennas to radiate more energy to the target
floor rather than directly up or down. Remember line of sight is your friend, the fewer obstacles
in the path the better. Avoid mounting the antenna near thick concrete pillars, unless for
intentional design purposes, as this will cast a wide weak signal shadow.
DO pick open ceiling areas, away from support pillars, or you’ll cast a shadow.
Dealing with high ceilings
Mounting omnidirectional antennas on high ceilings 15 ft or above has a number of problems.
Most of the energy is directed sideways towards other antennas causing co-channel
interference. Also, antenna gain shoots over the target area and data rates are reduced.
Wi-Fi design and optimization is often counter-intuitive. Many people erroneously think they
need to use high-gain omnidirectional antennas, unaware this only makes matters worse,
since the vertical beam width is narrower, which means clients get an even weaker signal, and
adjacent antennas get even more interference. It is actually more effective to depower the Tx
on standard omnidirectional antennas.
When you have high ceilings, consider wall mounted panel and sector antennas instead, and
mount them at 6-10 ft from the floor or you can mount patch or panel antennas on the ceiling.
DON’T mount omnidirectional antennas above 15 ft without doubling AP density, and
reducing Tx power.
DO consider sector, patch and panel antennas on walls and high ceilings.
Above suspended ceiling
For purely aesthetic reasons, some customers
conceal their APs or antennas above a suspended
ceiling (plenum space). This is a bad idea for
several reasons. First, in the ceiling space there is
often a lot of metal objects such as air ducts, which
causes reflections. Second, the acoustic ceiling
tiles themselves add attenuation to the signal
reducing signal strength. Line of sight is your friend,
always try to ensure antennas are visible to users.
Another common mistake is laying the AP on top of
the ceiling tile facing upward, not down. Of course
Fig 9. AP among ducts and pipes
now it is upside down, and it is radiating more of its RF energy to the floor above it, not the
floor below.
DON’T put antennas above suspended ceilings, this causes unnecessary reflections
and attenuation.
DO use proper mounting brackets to mount APs below suspended ceilings in the line
of sight of users.
EM Interference
Electromagnetic interference is your enemy, and it comes in many forms. Large electric motors
and heavy power sources are the big ones to watch out for in Enterprise deployments. Keep
antennas at least 15 ft from large electric motors such as conveyor belts, escalators and
elevators. Also avoid putting antennas near power panels, cable conduits and cable trays.
DON’T place antennas within 15 ft of electric motors, power ducts or cable trays.
Metal objects
Metal objects are unavoidable in the path
between the access point, and clients. However
when metal objects such as the reflectors of
light fixtures, metal air ducts, cable trays, metal
shelving or metal doors are in the proximity of
the antenna, they dramatically alter the nearfield radiation pattern from the antenna. The
metal object becomes a huge RF reflector, which
causes unwanted reflections and multi-path
propagation. RF spreads to unwanted areas and
antenna reception capability is degraded.
Fig 10. Surrounded by a metal cage!
Don’t place antennas close to metal obstructions, light reflectors or cable trays.
2.4 GHz planning
As you know, in the US and many other countries 2.4 GHz is limited to only three nonoverlapping 20 MHz channels. Because of this, your channel planning should go hand in hand
with antenna selection. You should use the 2.4 GHz band for maximizing coverage, and not
worry too much about maximizing performance on 2.4 GHz. You can use 5 GHz for that. For
the same reason, it is important that you don’t waste channels, by having a 2.4 GHz cell that is
throwing signal into areas where there are no users. Hence you should look out for places where
you can use panel or sector antennas to maximize coverage and maximize channel reuse.
DON’T waste 2.4 GHz channels by covering areas where there is no user demand.
DO try to use panel and sector antennas to maximize 2.4 GHz coverage.
Oversized cells
A common misconception is that more Tx power means more performance. More often than
not, the exact opposite is true, smaller cells are better. Increasing Tx power increases the
overlap between cells resulting in co-channel interference. This is explained in more detail in
the section on Coverage vs Capacity
DON’T turn up the Tx power to increase capacity, it will increase interference and
reduce capacity. It is better to reduce Tx and increase AP density.
Auto RF tuning
Many vendors tout the ability for their APs to auto-select channels and dynamically set their
own Tx power rates. While this may seem like a good idea, it is fraught with risks. If you leave it
on, the network can potentially thrash back and forth as a ripple of changes propagate through
the network, as a result of possibly minor interference in one location, say a microwave oven
turning on. The denser your channel plan, the more likely this is to happen. The automation
algorithms developed by Wi-Fi access point vendors have a tendency to misallocate both
channels and power levels, leading to an unstable system and a variety of Wi-Fi performance
issues. Sometimes they over compensate, leaving Tx power levels too low, which results in
coverage holes.
Auto-tuning does have its place though, especially when deploying a new network in an area,
or if you know that a neighbor, perhaps someone on a floor above or below you has recently
deployed a new network. However, it is best not to leave it unattended. You should always
double check the changes it has made, and record those changes and re-enter them into your
offline channel plan. If it seems to thrash continuously, turn it off and hunt down the root cause
of the interference.
Bear in mind that when an AP changes channels it drops all connections. Clients must reconnect on the new channel and that takes a moment. This is a big deal, for anyone using VoIP
or multimedia. Most auto-channel algorithms are concerned only with the condition of the
spectrum around them, and do not necessarily factor in some kind of weighting based on user
count or applications in use.
DON’T leave RF auto-tune unattended after initial deployment, keep your eye on it.
Microwave ovens
Beware of microwave ovens. Microwaves, along with ZigBee, Bluetooth devices and cordless
phones share the same unlicensed 2.4 GHz spectrum. Whenever the microwave oven is on,
you will likely see a marked degradation in performance, particularly around the center of the
band, since they operate at ~2.45 GHz.
DON’T put 2.4 GHz antennas near microwaves, this will causes intermittent interference.
2G, 3G, 4G, LTE
If you think Wi-Fi is immune to cellular signals, because they operate in a different frequency,
you’ll be surprised to learn that you’re only half right. Some organizations that find they have
weak in-building cellular signal decide to install mini-base stations and cellular antennas.
Others go whole hog, and deploy distributed antenna systems. To their surprise, Wi-Fi performance sometimes suffers. The reason is this: When the 2G, 3G antennas are too close to
access points, they can create harmonic distortions offset 300 MHz from the 2.1 GHz source,
and this falls in the 2.4 GHz spectrum, causing interference at the receivers of the AP.
PCS-1900 (EUR)
UMTS-1900 (US)
UMTS-2100 (EUR)
UMTS-1700 (US)
High power
mobile base
station signal
High power
mobile base
station signal
Distance appr. 300MHz
1.7 GHz
1.8 GHz 1.9 GHz
2.0 GHz
2.1 GHz
=> Harmonic distortion
lands at 300MHz
distance from source
2.2 GHz
2.3 GHz
2.4 GHz
2.5 GHz
=> Signal-to-noise ratio
degrades in WLAN receiver
and data transfer suffers
2.6 GHz
Fig 11. Base Station transmit signals degrade 2.4 GHz WLAN signal reception
DON’T put cellular antennas near Wi-Fi antennas it may cause harmonic interference.
There may be further interference problems looming on the horizon from LTE. In 2013
Qualcomm floated the idea of deploying LTE in unlicensed bands (LTE-U), particularly
focusing on the 5 GHz band, which is becoming the dominant band in Wi-Fi. The idea behind
LTE-U is to give mobile carriers access to more bandwidth which they can use for data
services, and to give them more control over the user than they currently have with Wi-Fi
offload, which more often than not, involves the user jumping onto someone else’s network,
which of course, the carrier cannot monetize (yet). Fortunately LTE-U is now part of the 3GPP
Release 13 work, and so will not be fully standardized until early 2016. Hopefully there is
enough resistance from within the 3GPP and outside to quash it altogether.
Paddle antenna angles
If your APs have multiple external paddle antennas, don’t point them all in exactly the same
orientation. It looks prettier of course, but if you tilt the antennas a little bit in different directions, you
can effectively create dual polarization, which may improve overall spatial stream performance.
Remember because mobile devices can be held at any angle, the antennas on mobile phones
usually radiate RF uniformly in both vertical and horizontal planes and can therefore work with AP
antennas in any polarity. More important than the polarity, is to monitor the radiation patterns you
get. You can do this with a spectrum analyzer or continuous monitoring sensors.
DON’T align all AP paddle antennas in the same direction. Adjusting the angles can
improve coverage or performance or both.
Metallic paint
Another innocent attempt to improve aesthetics is painting antennas, so they blend in. If there
is any metal in the paint this is a big problem. It causes attenuation due to the conductive
material. Plus it invalidates your warranty!
DON’T paint APs or antennas with metallic paint, this causes attenuation.
Polarity mismatch
In point-to-point and point-to-multipoint links the polarization of antennas is crucial.
For outdoor links vertical polarity is preferred as it tends to fare better over most types of
terrain. Horizontal polarization is often used when there are trees, or for very dense terrain.
For a strong link, the antennas at either end of the link must have the same polarization.
Mismatched or “out-of-phase” polarization can reduce gain by 20 dB rendering the link
virtually useless.
It is possible to use both vertical and horizontal polarization together in matched pairs, to allow
two RF systems using the same frequencies to use the same airspace without interfering with
each another.
DON’T mix polarizations between two antennas in a point to point connection.
Outdoor APs
Most vendors have environmentally hardened
versions of their access points designed for
outdoor deployment, but they are expensive. An
alternative approach is to put indoor APs inside an
enclosure. There are special watertight enclosures
designed for this purpose. NEMA enclosures of
Type 3 or above are suitable for Wi-Fi applications
in most outdoor conditions. When placing APs
in extreme indoor conditions such as damp,
humidity, cold or heat it is best to apply the same
Fig 12: Lockable NEMA enclosure
precautions as your would for a similar outdoor
location. These polycarbonate enclosures are also
good for protecting access points in high traffic public areas indoors or outdoors such as railway
stations or sports stadiums where they might get vandalized or tampered with.
DON’T put indoor APs outdoors without an appropriate weatherproof enclosure.
MIMO provides the best gains compared to non-MIMO setups, in environments where the
signal experiences a lot of reflections. Reflections can cause fast fading which means very
quick dips in detected power level. MIMO compensates for this by using several paths with
dedicated antenna pairs. While one stream is suffering from fading, the other may run very
well - bits keep moving with MIMO. In contrast, Non-MIMO devices experience more radical
variance in performance due to these power level dips.
However, running multiple streams usually means that each stream has lower Tx power. In
coverage type of deployments, lower power may cost you more than you win from the multiple
streams benefit. WLAN radios should dynamically switch to STBC (space time block coding)
mode when parallel MIMO streams seem to not reach the other end.
With STBC MIMO streams carry the same content essentially creating a parallel data stream
with equivalent user data content with different pairs of antennas. The benefit of this is again
the different propagation path the signal experiences when environment has reflections/multi
path propagation. Combining the data from both connections at the receiving end provides
protection against fast, location specific fading caused for example by reflections from metal
structures. If this dynamic STBC operation is not operating properly and since multiple MIMO
streams often use lower power/stream, then this may mean smaller coverage and lower cell
edge performance. Again, in areas with multipath propagation, MIMO with STBC may be
better than having a few dB higher power level.
Beamforming arrays are inherently different from MIMO in that the multiple columns of dipoles
work together to create a single high gain signal. The basic idea is that multiple antennas are
combined in a round robin fashion or some other algorithm, to radiate a high-gain beam to
areas that are known to have clients in them. This may seem rather pointless in high density
environments where clients are everywhere, so it is not completely clear where the threshold of
benefit lies in terms of user density.
Anyway, while both MIMO and beamforming work well, an antenna optimized for one method,
does not work so well for the other. There are numerous different techniques for beamforming
which are the subject of much stone-throwing and boasting by its proponents, and this is not
the place to get into that.
Coverage vs Capacity
As enterprises become more and more dependent on Wi-Fi, those with high user densities are
constantly demanding more performance. Cranking up transmit power is not the answer. Switching
to high gain antennas is not the answer. The correct approach is to increase the AP density.
Actually, increasing AP density is not the answer either - unless you simultaneously reduce
cell size of each radio, to reduce co-channel interference that would otherwise arise. So the
generally accepted best practice for scaling capacity is to depower APs to reduce cell sizes,
increase cell density and disable lower attach rates, so that clients can only attach at the
higher rates. The reason for doing this is that when clients attach at the slower Modulation
and Coding Scheme (MCS) rates, they consume more airtime than on faster rates, and this
reduces that aggregate throughput achievable.
De-powering APs may seem counter intuitive, but it is the only way to allow higher cell density
without massive interference. However, with cells being closer together, the consequences of
an over-powered cell are more severe, so it is important that you monitor your changes closely.
An over-powered access point raises the noise floor for any neighboring access points on
adjacent channels, effectively reducing the potential throughput of those APs.
DON’T increase AP density without revisiting your RF plan and reducing Tx power.
DO disable lower MCS attach rates to prevent low speed clients eroding bandwidth.
Site Surveys and RF Planning
Building a wireless network without a plan is a penny-wise, pound-foolish strategy. For the
sake of a few thousand dollars software investment, you’ll be astonished how many enterprises
think they know better and try to wing it. What many don’t seem to realize, is that over time, the
network in going to change. A lot! 802.11abg got replaced with the more powerful 802.11n,
and 802.11ac will replace that. AP densities will increase, radio cell sizes will shrink. New
features such as channel bonding come into play, and new client form factors introduced.
You may not need to do physical site surveys in every area, but a predictive planning tool is a
must. A predictive wireless planning tool gives you the means to figure out what performance
levels you should expect, how many access points you’ll need, and approximately where
you should place them for the best results. Almost all vendors have a predictive planning tool
that allows you to upload building floorplans, define the attenuation properties of building
materials, and then plan your coverage and capacity around it.
Planning tools are not perfect. You are always going to run into deployment obstacles in the
field. But they do provide a close approximation to the network you should deploy. What they
don’t do of course, is measure the performance you are getting after the fact.
For that you need a performance management platform.
Continuous Performance Monitoring
While on the spot site surveys using hand held analyzers, are invaluable when it comes to
initial deployment verification and troubleshooting, it is naive to regard site surveys as anything
more than a brief snapshot in time of the RF environment in your premises. The fact is, the RF
environment inside and outside your buildings is never static, it is constantly changing. It is
affected by furniture, people, machines, neighboring wireless networks, and adjustments to
your own network.
Even after carefully selecting the right locations and antennas for every AP being deployed,
and closely following deployment and placement best practices described here and
elsewhere, in order to maintain optimum network performance, there is no substitute for
continuous Wi-Fi performance monitoring.
About 7signal
7signal Solutions is a U.S.-based network technology company with a mission to make
wireless LAN networks work — reliably. The company’s groundbreaking platforms provide
Wi-Fi performance assurance and optimization for any vendor-supplied wireless network.
7signal’s solutions help ensure that all end-users in hospitals, institutions of higher education
and enterprises can connect and stay connected to their critical applications at all times.
Phone: 855-763-9526
Email: [email protected]
Twitter @7signal
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF