User manual | Excel Life and Arteor™ Dual Socket USB Charger Type A+C 1 2 2a

Excel Life and Arteor™
Dual Socket USB Charger Type A+C
EMUSB2AC and AR770USB2AC series
Range
Excel Life
Arteor
Series
EMUSB2AC
AR770USB2AC
Picture
Installation
In dry wall and wall cavities
USB ports
1 x Type A & 1 x Type C
USB output
5V d.c. 4.8A (2.4A max on Type A, 3.0A max on Type C)
Input
230-240V a.c. 50Hz
Mains connections
Via ‘A’ and ‘N’ wires
Standby power consumption
<0.07W
Overload protection on output
5.1A ± 0.2A
USB charging unit installation in powerpoints for EMUSB2AC and AR770USB2AC series
1
Push USB outlet into extra
function hole with arrows
facing up as shown
CLICK
2
Excel Life USB Charger to be used in conjunction with Excel Life devices.
Arteor USB Charger to be used in conjunction with Arteor devices.
Join wires with corresponding
mains cables in the ‘A’ and ‘N’
terminals of double GPO.
USB charger can be assembled with any extra function
hole available on powerpoints or switch plates.
Installation in switch plates for EMUSB2AC and AR770USB2AC series
1
Push USB mechanism into
extra function hole with
arrows facing up as shown.
2a Configuration with USB mechanism stand alone in
plate. Connect USB module wires to the mains cable via
insulated connectors (401 series) as per diagram below.
2b Configuration with USB mechanism
installed next to a switch on a
plate. Connect USB wires to switch
mechanism as per below.
ACTIVE - OUT
(TO LIGHT)
MAINS
WIRING OF USB DRIVER
TO MAINS WIRING WITH 401
CONNECTOR (REQ. NEUTRAL)
Insulated
connectors
401
Mains cable
NEUTRAL
IN
USB
MAINS
USB
ACTIVE
IN
Assembly in dry wall and wall cavities for EMUSB2AC and AR770USB2AC series
1
2
Mains cable
Brick wall
Brick wall
Plasterboard
0.8 Nm
Cable tie box to mains cable to
avoid strain on USB mechanism
Push in assembled unit
into the wall cavity
Metal
bracket
Wall cavity
Screw the unit to wall
with standard mounting
accessories and then fix
front plate
Wall cut-out for standard installation only
Recommended Cut-Out Sizes to Fit Finished Products
Used on
A
B
MIN
MAX
MIN
MAX
AR777X
96
100
60
66
ED777X
76
92
52
58
EDV777X
76
92
54
58
Min Wall
Cavity (mm)
50
Warranty
Customer Service
HPM Legrand will honour all statutory guarantees that you as a
consumer are entitled to rely upon under the Australian and
New Zealand Consumer Laws against a manufacturer including a
guarantee that this product is of acceptable quality.
For all Customer Service and Technical Support enquiries
please call Monday to Friday during business hours.
To make a claim under any statutory guarantee you should first contact
the supplier, or retailer from whom you purchased this product.
01/2017
• This product has been designed to operate on a nominal supply voltage of
230 - 240V a.c. +/- 6%.
• While charging two devices simultaneously, each port (including type C port) will
charge at 2.4A maximum.
• Cable wiring of different voltage systems, such as Low Voltage and SELV cables, shall
not share the same conduit
• This product must be installed and used as per these instructions.
• This product utilises intellectual property in the form of registered designs,
trademarks, and/or patents. Such intellectual property remains the property of HPM
Legrand in all cases
• HPM Legrand reserves the right to modify the specification of this product at any time.
Legrand Australia
1300 369 777
www.legrand.com.au
HPM Legrand New Zealand
0800 476 009
www.legrand.co.nz
ABN: 31 000 102 661
LE09708AAA
• This product must be installed by a licensed electrician.
• For indoor use only.
• Not suitable for installation in wall boxes or single brick applications.
• This product should not be installed in areas exposed to constant vibration,
temperature fluctuations, or areas of high humidity.
• This product contains no serviceable parts and no attempt should be made to repair
this product. If the product is faulty it should be discarded.
• This product has been designed to operate in ambient temperatures 5°C to 40°C.
• The material in this product may vary in colour from batch to batch. Colour matching
from one batch to another cannot be guaranteed.
• Electrical installations periodically receive transient over voltages. This product has
been designed to minimise the effect of such voltages on connected equipment. It may
not give full protection for extreme over voltage transients such as those resulting
from a close lighting strike.
HPML1260
Disclaimers

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project