advertisement
USER MANUAL
AVL DITEST DSS
DIAGNOSTIC SYSTEM SOFTWARE
Ident number: AT7683E
Revision:
Issue:
02
11 / 2016
Program version: From version 2.4.123.0
Data may change without notice.
All data valid at the time of print
FUTURE SOLUTIONS FOR TODAY
AVL DiTEST GmbH
Alte Poststrasse 156
A-8020 Graz / AUSTRIA
Tel: +43 316 787-0
Fax: +43 316 787-1460 [email protected] www.avlditest.com
Copyright © 2016 AVL DiTEST GMBH, all rights reserved.
The content of this publication may not be reproduced in any way or forwarded to third parties, either in part or in full, without the prior written consent of AVL DiTEST. This publication was created with due care such that AVL DiTEST is not liable for any remaining errors or omissions or for any damages arising therefrom.
AVL DiTEST DSS
Warning and Safety Notices
Warning and Safety Notices
This device manual contains important warning and safety notices that must be observed by the user.
The product is intended only for the highly specific use described in the user manual.
The most important prerequisites and safety measures for the use and operation of the product are also described to ensure faultless operation.
No warranty can be given and no liability is assumed for applications beyond the described use, irrespective of observance of the necessary prerequisites and safety measures.
The product may only be used and operated by personnel who, based on their qualifications, are capable of adhering to the necessary safety measures during use and operation. Only accessories and consumables supplied by AVL DiTEST or approved by AVL DiTEST may be used. The measurement results obtained from the product in question depend not only on correct functioning of the product, but also on a series of general conditions. The results delivered by the product must therefore be evaluated by a specialist (e.g. plausibility check) before further measures are taken on the basis of a delivered measurement.
Settings and maintenance work on open devices while still live may only be performed by trained specialists who are aware of the associated danger.
The product may only be repaired in the factory of origin or by specialists specifically trained to perform such repair.
When using the product, it must be ensured by a specialist that the test object or test system is not brought into any operational state that could result in damage to goods or endangerment of people.
User Manual I
Warning and Safety Notices AVL DiTEST DSS
II User Manual
AVL DiTEST DSS
Summarized Safety Notices
Summarized Safety Notices
DANGER
Danger to life by electric potential on vehicles with high voltage systems
Deadly high voltages are present on the HV energy store (HV battery) and on parts connected to it!
Make sure no-one can come into contact with the connections on the HV battery, connecting cables of the HV battery or other parts under high voltage!
WARNING
Danger to life by electric potential on the ignition system
The ignition system carries a deadly high voltage!
Do not touch the ignition system while the motor is running!
WARNING
Danger to life by electric potential on vehicles with Xenon light
A lighting system that uses a xenon light carries a deadly high voltage!
Do not touch the components of the xenon light while the lighting is turned on!
WARNING
Danger from harmful or irritating substances
When performing measurements on the running motor in closed rooms (workshops, test halls, etc.), extract the vehicle exhaust gases and ventilate the rooms thoroughly!
WARNING
Risk of burns from hot parts
Measurements must be performed at normal motor operating temperature or according to the test specification! Do not touch hot parts such as the motor, motor components or any of the entire exhaust system! Use cooling fans if necessary!
User Manual III
Summarized Safety Notices
WARNING
AVL DiTEST DSS
Risk of injury from rotating parts
Only ever perform work in the engine bay while the motor is not running and the ignition is turned off!
Do not touch any rotating parts such as alternator, radiator fan or their drives (e.g. drive belts)!
Make sure measurement cables are laid safely while the motor is running!
WARNING
Risk of injury from unsecured vehicle
Engage the handbrake or shift the gearshift to P (on automatics)!
Adequately secure the vehicle against rolling!
WARNING
Risk of explosions due to pyrotechnical setups and restraint systems
Testing and assembly work may only be performed by trained personnel!
Never test the igniter with a multimeter!
Only perform system tests with approved testing equipment!
Disconnect the battery when working on the airbag system!
When reconnecting the battery, the ignition must be turned off and there must be no person inside the vehicle.
Always store the airbag unit with the discharge side facing upwards or according to the storage specifications!
Never leave the airbag unit lying around unattended!
Protect the airbag unit against flying sparks, open fire and temperatures above 100°C!
Do not transport the airbag unit in the passenger space!
Do not allow the airbag unit to come into contact with oil, grease or cleaning agents!
An airbag unit that has been dropped from a height greater than 0.5 m must be renewed!
Dispose of untriggered airbag units!
Do not open or repair the airbag unit!
NOTICE
When maintaining the cutoff speed of diesel engines, observe the applicable manufacturer’s specifications!
NOTICE
Always turn off the ignition before connecting or disconnecting the OBD connector or the various
AVL DiTEST vehicle adapters!
IV User Manual
AVL DiTEST DSS
Contents
Contents
WARNING AND SAFETY NOTICES .............................................................. I
SUMMARIZED SAFETY NOTICES .............................................................. III
2 PREPARING FOR MEASUREMENT ................................................ 2-1
3 DIAGNOSTIC SYSTEM SOFTWARE (DSS) ..................................... 3-1
Language ................................................................................ 3-3
Asanetwork ............................................................................. 3-4
AVL DiGate 480 ...................................................................... 3-5
Workshop ................................................................................ 3-5
Logging ................................................................................... 3-6
Automatic Execution ............................................................... 3-6
Application window ................................................................. 3-6
Data Recording ....................................................................... 3-6
Device connections ................................................................. 3-7
3.1.2.1.12 BMW Key Reader ................................................................... 3-8
3.1.2.1.15 AVL SMOKE ......................................................................... 3-10
3.1.2.1.20 Manufacturer Options ........................................................... 3-12
3.1.2.2.1 Show Log File ....................................................................... 3-13
3.1.2.2.2 Dateien exporting .................................................................. 3-13
User Manual V
Contents AVL DiTEST DSS
3.1.2.3.4 Device connections ............................................................... 3-17
Customer/Vehicle Assignment .................................................................. 3-20
3.1.4.2.2 Diesel Values Display Program ............................................ 3-22
3.1.4.2.3 Gas Values Display Program ................................................ 3-23
3.1.5.1.1 Continuous Gas Measurement ............................................. 3-24
3.1.5.1.2 Continuous Opacity Measurement ....................................... 3-26
3.1.5.1.3 Continuous Gas & Opacity Measurement ............................ 3-27
3.1.5.2.1 Overview of EOBD Modes .................................................... 3-29
3.1.5.2.2 Establishing a Connection .................................................... 3-30
3.1.5.2.3 Mode 1 Actual Values ........................................................... 3-30
3.1.5.2.4 Mode 2 Freeze Frame .......................................................... 3-30
3.1.5.2.5 Mode 3 Read Error Memory ................................................. 3-30
3.1.5.2.6 Mode 4 Delete Error Memory ............................................... 3-31
3.1.5.2.7 Mode 5 Lambda Probe Values ............................................. 3-31
3.1.5.2.8 Mode 6 Sporadic Test Values ............................................... 3-31
3.1.5.2.9 Mode 7 Sporadic Error Memory ............................................ 3-31
3.1.5.2.10 Mode 8 Actuator Test ........................................................... 3-31
3.1.5.2.11 Mode 9 Vehicle Information .................................................. 3-31
3.1.6.1.1 Taking On Jobs from asanetwork ......................................... 3-33
3.1.6.1.2 Send Results to asanetwork ................................................. 3-34
Service Screen AVL SMOKE .................................................................... 3-38
Service Screen AVL HV Safety ................................................................. 3-43
VI User Manual
AVL DiTEST DSS Inhaltsverzeichnis
4 MAINTENANCE ................................................................................ 4-1
User Manual VII
Contents AVL DiTEST DSS
VIII User Manual
AVL DiTEST DSS
1 General
General
AVL DiTEST DSS (DSS: Diagnostic System Software) is the pioneering new software for the latest
AVL DiTEST MDS stations (MDS: Modular Diagnostic Station).
Features:
Compatible with the following MS Windows operating systems:
- Windows® XP Prof. (32-bit)
- Windows® 7 (32-bit)
- Windows® 8
Flexible and sustainable thanks to a modular concept
- Existing AVL modules can be easily integrated
- Communication with PC via Bluetooth or USB
Multiple functions:
- Completely scalable screen
- Simple customer and vehicle management
(vehicle selected once only for all applications)
- Independent, country-specific software
(examples:"AU Ge rmany", "§57a" Austria, "MOT UK","OM“ Switzerland") for performing official emissions tests.
- Simple, rapid exhaust emissions analysis without running through the complete emissions test
- Results logs for all applications easily exported in standard PDF format
- Detailed service screens for all hardware modules; rapid and effective self-diagnostics for the hardware modules; software application system information
Automatic system updates
Vehicle data, device firmware updates and license updates
Vehicle databases rapidly loaded
User-friendly software
- User "guided" through the emissions test
- Easy-to-follow graphical and text-based help screens
Multiple applications can be run in parallel
Internet software updates available:
An incremental software update concept only downloads those program components which need a software update
Twin operation
Application screen assignment retained upon restart
Wide range of network connection options:
- Easily connect to the company network as NW client
- Connection to AUplus QM System
- asanetwork-compatible
User Manual 1-1
General
1.1 Operation
AVL DiTEST DSS
AVL DiTEST DSS is operated using a conventional computer mouse and keyboard.
1.1.1 DSS Application Window
(1)
(2)
(3)
(4)
Fig. 1-1 (example: continuous gas measurement with module AVL Digas 480)
(1)
(2)
(3)
(4)
Taskbar:
File for closing applications, stopping devices and exiting AVL DiTEST DSS.
Tools for a range of settings, displaying/exporting log files, updating the system
(license, vehicle data and devices) and backing up/restoring the system.
“ Extras”)
Note:
The functions available under "File" and "Tools" depend on the selected application.
Only the functions relevant to the selected application will be displayed.
Vehicle information:
This is where you can inspect the vehicle identification data. ( Cap. 1.1.4
“Infobox”)
Application:
This is where the current operating mode is displayed.
“Diagnostic system Software (DSS)”
Operating bar:
Displays the available function buttons.
1-2 User Manual
AVL DiTEST DSS
1.1.2 User Prompts
User prompts are displayed optically by symbols on the screen.
Slow, continuous speed increase by slow, continuous pushing on the gas pedal.
Waiting for recognition of the deviation.
Slow, continuous speed decrease by
Deviation recognized. slow, continuous removal of pressure from the gas pedal.
Maintain speed.
Deviation not recognized.
General
Accelerate as fast as possible until cut-off speed is reached.
Waiting for recognition of the cut-off.
Decelerate as fast as possible. Cut-off recognized.
Control loop check:
Apply disturbance value.
Cut-off not recognized.
Control loop check:
Remove disturbance value..
User Manual 1-3
General
1.1.3 Help
Help text appears when you click on or on .
Durch Klicken auf erscheinen zusätzliche Informationen.
1.1.4 Infobox
A window (Infobox) with vehicle data can be displayed at the top of the screen.
Opens the Infobox
Closes the Infobox
1.1.5 Switching on
AVL DiTEST DSS
Double-click on or click Start All programs AVL DITEST AVL DSS .
1.1.6 Quitting and switching off the application
Click on or exit AVL DiTEST DSS by clicking File Quit .
NOTICE
Do not disconnect your PC until you have correctly exited AVL DiTEST DSS and WINDOWS!
Click Start Shutdown Shutdown .
1-4 User Manual
AVL DiTEST DSS
2 Preparing for Measurement
Preparing for Measurement
All measurement preparation steps described are started automatically by the device.
2.1
Leak Test
The AVL exhaust gas tester demands a leak test once a day!
When prompted, close off the probe and press F8 Next .
The leak test will be performed and the exhaust instrument tested for leaks.
Once the leak test is complete, unblock the exhaust probe again and the program will continue where it left off.
2.2
HC Residue Test
Before every exhaust measurement, an HC residue test must be performed on the AVL exhaust gas tester.
This serves to measure the HC value in the measurement system and the ambient air, and lasts for
80 seconds.
Remove the exhaust probe from the exhaust pipe.
F8 Next starts the HC residue test.
The measured HC value must be below 20 ppm. If this is the case, then the measurement will continue automatically (sometimes even before the 80 seconds are up).
If the HC value is above 20 ppm, then check whether the exhaust probe is in the exhaust stream; note that high quantities of fuel residue can also exist in the ambient air. In this case, change the testing location or ventilate the room.
Wait until the HC residue test is complete.
Once the HC residue test is complete, you have the options:
F5 Repeat to repeat the HC residue test, if errors occurred.
F8 Next to continue the process.
User Manual 2-1
Preparing for Measurement
2.3
Warm-Up Phase
AVL DiTEST DSS
After switching on, the AVL exhaust gas tester requires a warm-up time of up to one minute.
(Older modules up to 15 minutes).
You must wait out this warm-up phase in order to obtain stable measurement values.
2.4
Stability Test
Before each measurement, the AVL exhaust gas tester runs through a stability test. The exhaust probe must not be in the exhaust stream during this test.
This test runs automatically and takes about 20 seconds.
2-2 User Manual
AVL DiTEST DSS
3 Diagnostic System Software (DSS)
3.1
DSS Manager
Fig. 3-1
Diagnostic System Software (DSS)
User Manual 3-1
Preparing for Measurement
3.1.1 File
AVL DiTEST DSS
3.1.1.1 Close all applications
File Close all applications will close all applications with the exception of the DSS Manager.
3.1.1.2 Stop devices
Applications which use devices (AVL AUX, AVL GAS …) or device drivers will be closed.
Always click File Stop devices before disconnecting devices from a USB interface.
After inserting the USB plug, click F8 next .
NOTICE
Never disconnect/connect devices from/to a USB port without clicking File Stop devices (and afterwards pressing F8 next ).
The PC might no longer respond. If this happens, restart the PC.
3.1.1.3 Quit
AVL DiTEST DSS is exited via File Quit or by clicking .
3-2 User Manual
AVL DiTEST DSS
3.1.2 Tools
3.1.2.1 Settings
Diagnostic System Software (DSS)
Fig. 3-2
3.1.2.1.1 Language
Click on ExtrasSettingsLanguage .
Here, you can select the desired language.
OK
Cancel
Apply
Help
Quits the “Language” function. The application window appears.
Quits the “Language” function without saving changes.
Applies the entered values.
Shows help text.
Information
The buttons OK, Cancel , Apply and Help always have the same function under “Tools” and will not be discussed any further below!
User Manual 3-3
Preparing for Measurement
3.1.2.1.2 Asanetwork
AVL DiTEST DSS
Click on ExtrasSettingsasanetwork .
Service Location DLOC
The asanetwork location is entered during installation under “Service Location DLOC”.
Only ever change this entry if necessary, for example, if several stations are operated in the network.
Additional services
Target Data Service:
Enable the Set value service if your asanetwork provides a choice of nominal data.
Advanced vehicle type data:
Enable Extended vehicle data information if your asanetwork provides an extended choice of vehicle type data such as date of first registration, fuel type and engine code.
Unsent result protocols of exhaust emission tests
If you select Enable deleting of obsolete results , then obsolete results will be deleted automatically.
If Delete with user confirmation is selected, then results will only be deleted upon confirmation.
With Delete after (in days) , you can define how many days unsent AU results logs will be kept on the local system before being automatically deleted.
Sent AU event logs
Save sent AU event logs:
Check this box if you wish for sent AU results logs to remain saved after sending.
Days to save:
Set here the number of days a sent results log should be kept before it is automatically deleted.
This option is only available if “Save sent AU results logs” has been selected.
Order view
By selecting Standard or Extended , you can select the view (i.e. display of additional data in the form of additional columns) of jobs over the workshop network.
Show completed jobs
If Show completed orders is enabled, then the completed jobs will be displayed under “Orders”,
“asanetwork” and “Select orders”.
3-4 User Manual
AVL DiTEST DSS
3.1.2.1.3 AVL DiGate 480
Diagnostic System Software (DSS)
Click on ExtrasSettingsAVL DiGate 480 .
Directory for backup classified according to year and month
If this option is enabled, then the network drive on which the results shall be saved (in XML and
PDF format) can be selected by clicking on .
The connection to the network drive can be tested with Test .
Directory for transmission to external applications
If this option is enabled, then the network drive on which the results shall be saved for forwarding to external applications (in XML format) can be selected by clicking on .
The connection to the network drive can be tested with Test .
3.1.2.1.4 Workshop a) Address
Click on ExtrasSettingsAddress and enter your details in the labeled fields. b) Personnel
Click on ExtrasSettingsPersonnel .
Clicking New opens an input window into which you can enter the name of a new tester. Return to
“Tester” with OK .
Clicking Delete deletes the blue-highlighted tester name.
Clicking Edit opens an input window in which you can edit the blue-highlighted tester name. Return to “Tester” with OK .
Clicking Current Operator selects the blue-highlighted tester name (or clicking the desired tester name).
Clicking Responsible Operator selects the blue-highlighted tester name (or clicking the desired tester name). c) Report
Clicking Add opens a window in which you can select your logo. Click Open to confirm the choice of logo.
Logos can be inserted in BMP, JPG and GIF format.
You can delete the selected logo by clicking Remove .
With Show workshop address on reports , you can define whether the workshop address shall appear on the log or not.
With Show vehicle data on reports , you can define whether the vehicle data shall appear on the log or not.
These settings do not affect the logs of official measurements (AUs).
User Manual 3-5
Preparing for Measurement
3.1.2.1.5 Logging
AVL DiTEST DSS
Click on Extras Settings Logging .
All of the user‘s interactions can be recorded and saved for servicing purposes by enabling
Logging .
You can drag the slider to set the size of log file that will trigger a warning upon exporting.
Clicking opens a window with which you can specify the location for saving the log file.
3.1.2.1.6
Automatic Execution
Click on ExtrasSettingsAutomatic execution .
Executing functions automatically:
Check the box next to those functions you wish to start automatically.
3.1.2.1.7 Application window
Click Tools Settings Application window .
You can set the size and position of the application window by clicking on "Save window position and size".
You can set the application window to appear in the taskbar minimized by clicking "Start window in minimized mode".
3.1.2.1.8
Data Recording
Click on ExtrasSettingsData records .
In the “Sampling rate” field, select the desired sampling rate in milliseconds.
You can choose the directory in which to save the data recordings by clicking on .
Also observe Chapter 3.1.5.1.1
“Continuous Gas Measurement”, Chapter. 3.1.5.1.2 „Continuous
Turbidity Measurement
“and Chapter 3.1.5.1.3 “Continuous Gas & Turbidity Measurement “.
3-6 User Manual
AVL DiTEST DSS
3.1.2.1.9 Device connections
Click Tools Settings Device connections .
Diagnostic System Software (DSS)
If "Open automatically upon start-up" has been disabled, the "Device connections" dialog box will
not appear when you start AVL DiTEST DSS( Cap. 3.1.2.1.9
„Device connections“).
3.1.2.1.10 Bluetooth
Click on ExtrasSettingsBluetooth .
Here, you can select the Bluetooth stack (Bluetooth driver) to use.
„Autodetect" is the default setting.
3.1.2.1.11 AVL OBD
Information
The standard AVL DiTEST MDS with AVL DiOBD comes with a Bluetooth connection.
A USB cable can alternatively be supplied for the PC connection.
Click on ExtrasSettingsOBD .
Scantool
Here you can select which scan tool and what connection type to be used.
COM port settings
If you deactivate the function COM-Port Auto detection , you can change the COM port for the AVL
OBD manually.
You can select the COM port to be used by clicking on the list field.
Logging
By clicking on Scantool communication (continuous) , you can set the scan tool communication to be logged continuously. As a rule, this option should be disabled, since it can lead to an enormous volume of data.
User Manual 3-7
Preparing for Measurement AVL DiTEST DSS
Bluetoothverbindung
Ist „Bluetooth“ aktiviert, so können Sie Sie durch Klicken auf manuell nach dem Bluetooth-
Gerät suchen.
Opening the search dialog box automatically launches the search for Bluetooth devices in the device group.
Fig. 3-3 Example AVL DiTEST DiOBD 880
If the Bluetooth device used is found, then click on it and then click OK .
3.1.2.1.12 BMW Key Reader
Click Tools Settings BMW KeyReader.
Path to BMW KeyReader file
Path to the BMW KeyReader file which is to be imported. This file is generated by the BMW
KeyReader software as soon as a key is found. The export settings must match the corresponding import settings.
You can test the connection to the selected path by using Test .
Automatically delete file will automatically delete the BMW KeyReader file after import. This point should usually be disabled.
URL of the "SAM" web service
Enter the URL of the SAM web service for key data interpretation.
This is usually http://localhost:8080/soap/servlet/soaprouter.
You can test the connection to the SAM web service using
Test
.
Timeout
Enter the period of time in seconds after which an unsuccessful connection attempt will be cancelled.
3-8 User Manual
AVL DiTEST DSS
3.1.2.1.13 AVL HV Safety
Information
Diagnostic System Software (DSS)
AVL HV Safety is connected to the PC with a USB cable.
Click Tools Settings AVL HV Safety .
Select USB.
If "Serial" is enabled, you can select the COM port used from the list box.
3.1.2.1.14 AVL AUX
Information
Stationary MDS stations:
Standard AVL AUX – PC communication is via USB cable.
Mobile MDS stations:
Standard AVL AUX – PC communication is via Bluetooth.
Click on ExtrasSettingsAVL AUX .
You can click to select the interface to be used by the AVL AUX.
If "Bluetooth" is enabled, you can search manually for the Bluetooth device by clicking .
Opening the search dialog box automatically launches the search for Bluetooth devices in the device group.
AVL AUX
Fig. 3-4
If the Bluetooth device used is found, click on it and then on OK .
If "Serial" is enabled, you can select the COM port used from the list box.
User Manual 3-9
Preparing for Measurement
3.1.2.1.15 AVL SMOKE
Information
AVL DiTEST DSS
The standard AVL DiTEST MDS with AVL SMOKE comes with a Bluetooth connection. An RS232 cable can alternatively be supplied for the PC connection.
Click on ExtrasSettingsAVL SMOKE .
You can click to select the interface to be used by the AVL SMOKE.
If “Bluetooth” is enabled, then you can search manually for the Bluetooth device by clicking on .
Opening the search dialog box automatically launches the search for Bluetooth devices in the device group
AVL SMOKE
Fig. 3-5 Example AVL DiSmoke 480
If the Bluetooth device used is found, click on it and then on
OK
.
If Bluetooth is not being used, USB should be selected by default to ensure the automatic COM port recognition works.
If your AVL SMOKE connected to the PC by RS232 cable, then select “Serial”. In the list box, select the COM port used.
3-10 User Manual
AVL DiTEST DSS
3.1.2.1.17 AVL GAS
Information
Diagnostic System Software (DSS)
Stationary MDS stations:
Standard AVL GAS – PC communication is via USB cable.
Mobile MDS stations:
Standard AVL GAS – PC communication is via Bluetooth.
Click on ExtrasSettingsAVL GAS .
You can click to select the interface to be used by the AVL GAS.
If "Bluetooth" is enabled, you can search manually for the Bluetooth device by clicking .
Opening the search dialog box automatically launches the search for Bluetooth devices in the device group.
AVL GAS
Fig. 3-6
If the Bluetooth device used is found, click on it and then on OK .
If "Serial" is enabled, you can select the COM port used from the list box.
User Manual 3-11
Preparing for Measurement
3.1.2.1.18
Applications
AVL DiTEST DSS
This is where you will find the settings for country-specific emissions tests ("AU Deutschland" -
"German emissions test").
3.1.2.1.19 HV Safety
Click Tools Settings Applications HV Safety .
Results
Enabling "Save automatically" will automatically save the measurement results.
Automatic feedback
Enabling "On" activates a feedback signal during measurement.
Tester
If "Use tester" is enabled, the name of this tester will be needed when you start measuring with the
AVL HV Safety.
Click on "Password input" to enter the tester name and set a password.
Vehicle identification
If "Use vehicle identification" is enabled, the vehicle identification data will be included in the test report.
Activation of specific measurements
Here you can activate measurements "insulation monitor review", "SAE J 1766 Measurement" and activate "overall measurement".
3.1.2.1.20
Manufacturer Options
Click on ExtrasSettingsManufacturer options .
In this password-protected area, you can make further specific settings.
3-12 User Manual
AVL DiTEST DSS
3.1.2.2
Log File
Also refer to Chapter 3.1.2.1.5
“Logging” with regard to this.
3.1.2.2.1
Show Log File
Diagnostic System Software (DSS)
Click on ExtrasLogging fileDisplay .
A window appears showing the log file.
3.1.2.2.2 Dateien exporting
Click on ExtrasLogging fileExport .
The entire log or individual log files can be exported. a) Export all log files
F8 Next The entire log will be compressed.
F5 Directory A window opens in which you can select the saving location. Continue with OK .
F8 Next
F8 Confirm
Creates a zip archive of the entire log.
Exports the entire log; back to main window. b) Export individual log files
F5 Selection Shows the log files.
F2 Choose
F3 Discard
Selects all log files.
Discards the selected log files.
Selects a log file.
F8 Next
F8 Next
F8 Next
F8 Confirm
The anticipated file size is shown.
Compresses the log files.
F5 Directory A window opens in which you can select the saving location. Continue with OK .
Creates a zip archive of the entire log.
Exports the entire log; back to main window.
User Manual 3-13
Preparing for Measurement
3.1.2.3 System-Update
AVL DiTEST DSS
Here you can update the licenses, vehicle data and device firmware of your AVL DiTEST MDS stations.
3.1.2.3.1
License
Die Lizenz kann sich auf einer CD befinden oder Sie erhalten die Lizenz per Email in Form einer
Lizenzdatei (*.lic).
1. Insert the CD with the license in the DVD drive or copy the license to a USB flash drive and insert the flash drive into a free USB port.
2. Click on ExtrasSystem UpdateLicense .
3. The dialog "License Update" appears
On the left side you will see the existing licenses.
Show by clicking on one of the licenses and the content of the dongle are displayed details of the dongle and the selected license in the right part of the screen.
4. Click on F2 File .
A window opens in which you can select the license.
Confirm the selection by clicking Open .
The license can now be updated over the Internet.
Click on F3 Internet .
If the Internet connection exists, the license file will be downloaded automatically.
Click Write to dongle to transfer the license to the dongle.
5. You can print the screen with F4 Print .
6. With F5 Skip , you can prevent the license update.
7. You can see all licenses in the area on the left.
In the area on the right, you can see a detailed view of the license that has been highlighted in blue on the left.
Click on the appropriate license and then click F8 Next .
The license will be transferred to the dongle.
8. Complete the license update by clicking F8 confirm .
3-14 User Manual
AVL DiTEST DSS
3.1.2.3.2
Vehicle Data
Diagnostic System Software (DSS)
The vehicle data are located on a CD in the form of a self-extracting file (*.exe).
Installing vehicle data:
1. Quit AVL DiTEST DSS if it has been started.
2. Insert the CD with the Sfx installation package in the DVD drive.
If a window does not open automatically, double-click on the autostart.exe
file.
3. Click Vehicle data update for DSS V2.2
.
4. Click on the vehicle data package which you wish to install, e.g. [08/2010].
5. An installation program will start.
Follow the instructions and confirm all messages by clicking
F8 next .
6. The available license and vehicle data will be copied to the AVL DITEST DSS system directory to enable direct access to this data during the update.
Quit the installation program by clicking .
Updating vehicle data:
1. Start AVL DiTEST DSS by double-clicking AVL DiTEST DSS .
2. If the update does not start automatically with the dialog "License update" (see step 3), click
Tools
System update
Vehicle data .
3. This opens the "License update" dialog.
You can update the license.
You can prevent the license update with F5 Skip .
(See "License" for details.)
4. The vehicle data currently installed will be displayed. Continue with F8 Next .
5. Select the source of vehicle data.
Click Locally installed versions and F8 Next .
6. Check the box next to the vehicle data to be updated and click
F8 Next .
7. A summary of the system update will be shown.
You can print the system update with F4 Print .
8. Complete the system update by clicking F8 Confirm .
User Manual 3-15
Preparing for Measurement
3.1.2.3.3 Device
AVL DiTEST DSS
Device firmware is automatically updated after an AVL DiTEST DSS software update.
Please follow the AVL DSS Brief Instructions, AVL DiTEST identification number AT7260ML, for
AVL DiTEST DSS software installation and updates. These can be found in the DVD sleeve.
If the device data are in the form of a self-extracting file (*.exe) on a data carrier (CD, USB flash drive, etc.):
Installing device data:
1. Quit AVL DiTEST DSS if it has been started.
2. Insert the CD with the device data in the DVD drive or copy the device data to a USB flash drive and insert the flash drive into a free USB port.
3. Start Windows Explorer .
Search for and double-click on device update file(s).
4. The available device data will be copied to the AVL DITEST DSS system directory to enable direct access to this data during the update.
5. Quit Windows Explorer .
Updating vehicle data:
1. Start AVL DiTEST DSS by double-clicking on AVL DiTEST DSS .
2. If the update does not start automatically with the dialog "License update" (see step 3), click
Tools
System update
Device data .
3. This opens the "License update" dialog.
You can update the license.
You can prevent a license update with F5 Skip .
(See "License" for details.)
Click F8 Next .
4. Connect all devices and switch the devices on.
Wait until all devices are available and then confirm with F8 Next .
NOTICE
The devices must be connected to the power supply during the firmware update!
5. The necessary firmware updates will be determined and automatically installed.
6. A summary of the system update will be shown.
You can print the system update with F4 Print .
7. Complete the system update by clicking F8 Confirm .
3-16 User Manual
AVL DiTEST DSS
3.1.2.3.4 Device connections
Diagnostic System Software (DSS)
You can select the type of connection (Bluetooth or USB) for the individual devices (AVL SMOKE,
AVL GAS, AVL AUX and AVL OBD) with Tools Update system Device connections .
NOTICE
MDS stations come with the correct connection types already configured.
Bluetooth devices
If more than one Bluetooth device is found, click on the Bluetooth device used by your MDS station.
Devices (AVL OBD)
You can select the OBD module used in the list box.
Automatically identify COM port (AVL OBD)
If this item is enabled, the system will automatically look for the COM port used.
"Automatically identify COM port" should be enabled if the connection type "USB" has been selected.
COM port (AVL OBD)
If "Automatically identify COM port" is disabled, you can select the COM port used from the "COM
port" list box.
Bluetooth stack
This is where you can select the Bluetooth stack (Bluetooth driver) used.
The default setting is "Autodetect".
Connection okay.
F2 Bluetooth
F3 USB
Devices have previously been connected to the software; however, the most recently connected devices cannot currently be accessed.
The device cannot be accessed.
"Bluetooth connection" is selected for all devices.
"USB connection" is selected for all devices.
Display information on the connection status if an intact connection could not be established.
User Manual 3-17
Preparing for Measurement
3.1.2.4 Backup
AVL DiTEST DSS
This backs up the data on your system.
Click on ExtrasBackup .
Select the data to be backed up from:
Settings
Results / Customer data / Vehicle data
All
F8 Next The data backup commences.
F5 Directory A window opens in which you can select the saving location. Continue with Open .
F8 Next
F8 Next
The location and the backup data will be displayed
This data will be backed up.
.
Continue to the AVL DiTEST DSS window. F8 Next
3.1.2.5 Restore
This backed-up data can be restored.
Click on ExtrasRestore .
F5 Directory A window opens.
Select the file to be recovered and click Open .
The restored file is displayed.
Go to F8 Next .
Select the data that you want to restore and click Next F8 .
The data and the source of the data for restoration are displayed.
Go to F8 Next .
Files will be restored. With F8 Next continue to the main window.
3-18 User Manual
AVL DiTEST DSS
3.1.3 Customer Management
3.1.3.1 General
Diagnostic System Software (DSS)
The customer management system consists of the:
Customer area: for creating, editing, deleting and printing customer data (1)
Vehicle area: for creating, editing, deleting and printing vehicle data (2)
for linking and unlinking customer and vehicle data (3).
(3)
(1)
(2)
(1a)
(2a)
Fig. 3-7
3.1.3.2 Customer Area
List of costumers: If no filter is active, then all customer records will be displayed.
Filter: A filter can be applied by clicking on a cell in the first row and then clicking on the arrow.
Sort: The table can be sorted by pressing on the table header.
Narrow down: If you enter, for example, *Inc*, then only entries containing “Inc” will appear in the corresponding column.
Customer details: If you select a row in the customer list, then the customer record will be displayed in the area (1a). If one or more vehicles are assigned to the customer, then the license number will be shown at the end of the customer record. Clicking on the license number displays the vehicle details in the Vehicle List area (2a).
F2 New
F3 Edit
F4 Delete
Printer icon
F1 Help
A field appears into which you can enter data to create a new customer record.
<< Cancel
F8 Save
The input will be discarded.
The input will be saved.
If a record is selected, then it can be edited by pressing F3 .
<< Cancel
F8 Save
The input will be discarded.
The input will be saved.
If a record is selected, then it can be deleted by pressing F4 .
If a record is selected, then it can be printed.
On safety grounds, the entire list cannot be printed.
Brings up a window providing further information about customer management.
User Manual 3-19
Preparing for Measurement
3.1.3.3 Vehicle Area
AVL DiTEST DSS
List of vehicles: If no filter is active, then all vehicle records (vehicle list) will be displayed.
Sort: The table can be sorted by pressing on the table header.
Narrow down: If you enter, for example, *1234*, then only entries containing “1234” will appear in the corresponding column.
Vehicle details: If you select a row in the vehicle list, then the vehicle record will be displayed in the area (2a). If the vehicle is assigned to a customer, then the customer’s name will be shown at the end of the deta iled information. Clicking on the customer’s name displays the customer record in the area (1a).
F5 New
F6 Edit
F7 Delete
Printer icon
A field appears into which you can enter data to create a new vehicle record.
F2 Type select can be used to identify the vehicle in a licensed vehicle d atabase (HSN, TSN, manufacturer, model, engine code…).
<< Cancel The input will be discarded.
F8 Save The input will be saved.
If a record is selected, then it can be edited by pressing F6 .
<< Cancel
F8 Save
The input will be discarded.
The input will be saved.
If a record is selected, then it can be deleted by pressing F7 .
If a record is selected, then it can be printed.
F1 Help
On safety grounds, the entire list cannot be printed.
Brings up a window providing further information about customer management.
3.1.3.4 Customer/Vehicle Assignment
One or more vehicles can be assigned to a customer.
If a customer and a vehicle are selected, then the records will be linked
(customer data assigned the vehicle data).
F1 Help
This unlinks records.
Brings up a window providing further information about customer management.
3-20 User Manual
3.1.4 AU
AVL DiTEST DSS Diagnostic System Software (DSS)
AVL DiTEST DSS includes countryspecific software (examples: “AU Germany”, “§57a” Austria, “MOT
UK”) for performing an official emissions test. To start the installed application, click on OMOM start .
The respective application is certified and runs according to the legal requirements. (Example:
Guideline for Germany). All AU applications include the starting points for filter test (see Chapter
3.1.4.2.1), Diesel values display program (see Chapter 3.1.4.2.2 and Gas values display program (see
3.1.4.1 File
Please refer to Section 3.1.1 "File". Only "Quit" will appear here.
3.1.4.2 Extras
“Extras". Only the functions relevant to the "AU" will appear here.
User Manual 3-21
Preparing for Measurement
3.1.4.2.1 Filter test
Start the filter test by clicking AU Filter test .
AVL DiTEST DSS
For further details on the filter test: see Device Manual AVL DiSmoke 480 BT, Section 3.7 "System
Check with Filter".
3.1.4.2.2 Diesel Values Display Program
Information
This function is required for calibration of AVL DiSmoke 480.
Click on AU Diesel Values Display Program .
A window appears showing:
Silicon serial number and firmware version/checksum of the measurement module
Driver version/checksum and display version/checksum
Actual turbidity values
Maximum absorption value
Actual absorption value
Logbook:
Read Logbook A window appears showing the logbook entries.
Close the “Read Logbook” function by clicking OK
Closes the window with the logbook entries.
Measuring turbidity and absorption:
F8 Next Starts the measurement display.
F6 Reset
F8 Next
Resets the maximum absorption value.
Ends the diesel values display program.
3-22 User Manual
AVL DiTEST DSS
3.1.4.2.3 Gas Values Display Program
Information
Diagnostic System Software (DSS)
This function is required for calibration of AVL Gas 1000.
Click on AU Gas Values Display Program .
A window appears showing:
Silicon serial number and firmware version/checksum of the measurement module
Driver version/checksum and display version/checksum
Values for CO, CO
2
, O
2
and HC
Logbook:
Read Logbook A window appears showing the logbook entries.
Close the “Read Logbook” function by clicking OK .
Closes the window with the logbook entries.
Measuring the gases:
F8 Next Starts the measurement display.
F8 Next Ends the gas values display program.
User Manual 3-23
Preparing for Measurement
3.1.5 Diagnostic
Fig. 3-8
3.1.5.1 Exhaust Analysis
AVL DiTEST DSS
3.1.5.1.1 Continuous Gas Measurement
In this operating mode, the concentrations of the gases CO, CO
2
, HC and O
2
can be measured without running through the AU procedure.
Speed and engine temperature can also be measured.
Engine settings can be made under direct observation of noxious emission values.
Click on DiagnosticEmission analysisGas .
The measurements will be shown.
The following settings are related to AVL AUX.
When using the AVL 480 DiLink note the settings in the Cape. 3.1.5.1.4.
F2 Sensor
F3 Sensor
Select the sensor for the engine temperature measurement.
Manual input Enter the engine temperature.
Temperature sensor ---
EOBD Press F5 Connect to establish a connection
F8 Confirm to the OBD module.
Back to the measurement display.
Select the sensor for speed measurement.
DiSpeed Select "Internal/external".
For "internal", select "Car/truck", "4-stroke motorcycle “ or "2-stroke motorcycle".
EOBD
F8 Confirm
Press F5 Connect to connect to the OBD module.
Back to the measurement display.
3-24 User Manual
AVL DiTEST DSS
F4 Timing
F5 Fuel type
F6 Freeze
F7 Record
F8 Log
<< Cancel
Diagnostic System Software (DSS)
---
Select the fuel type.
F8 Confirm Back to the measurement display.
"Freezes" the measurement display.
F6 Continue Continues the continuous measurement.
Continuously records the measurements and writes them to a text file.
Please also refer to 3.1.2.1.8 "Data Recording".
F7 Quit Quits continuous measurement recording.
Creates a results log.
F3 Identification
F4 Print
F5 Edit
"Vehicle identification" will appear.
F8 Next Quits vehicle identification.
Prints the results log.
This is where you can edit the results log
(display workshop and vehicle data: yes/no).
F5 Apply
Saves the results log in the internal database (see also Results
management).
Quits results log
editing.
F6 Save
F8 Next Back to continuous gas measurement.
Quits continuous gas measurement.
User Manual 3-25
Preparing for Measurement
3.1.5.1.2 Continuous Opacity Measurement
AVL DiTEST DSS
In this operating mode, you can measure turbidity without running through the AU procedure.
Speed and oil temperature can also be measured.
Engine settings can be made under direct observation of noxious emission values.
Click on Diagnostic Emission analysisOpacity .
The measurements will be shown.
The following settings are related to AVL AUX.
When using the AVL 480 DiLink note the settings in the Cape. 3.1.5.1.4.
F2 Sensor
F3 Sensor
Select the sensor for the engine temperature measurement.
Manual input Enter the engine temperature.
Temperature sensor ---
EOBD Press F5 Connect to establish a connection
F8 Confirm to the OBD module.
Back to the measurement display.
Select the sensor for speed measurement.
DiSpeed Select "Internal/external".
For "internal", select "Car/truck", "4-stroke motorcycle" or "2-stroke motorcycle".
EOBD Press F5 Connect to establish a connection with the OBD module
F4 Timing
F6 Freeze
F7 Record
F8 Log
<< Cancel
F8 Confirm
---
Back to the measurement display.
"Freezes" the measurement display.
F6 Continue Back to continuous measurement.
Continuously records the measurements and writes them to a text file.
Please also refer to 3.1.2.1.8 "Data Recording".
F7 Quit Quits continuous measurement recording.
Saves the results log.
F3 Identification
F4 Print
F5 Edit
"Vehicle identification" will appear.
F8 Next Quits vehicle identification.
Prints the results log.
This is where you can edit the results log
(display workshop and vehicle data yes/no).
F6 Save
F5 Apply Quits results log
editing.
Saves the results log in the internal database (see also Results management).
F8 Next Back to continuous turbidity measurement.
Quits continuous turbidity measurement.
3-26 User Manual
AVL DiTEST DSS
3.1.5.1.3 Continuous Gas & Opacity Measurement
Diagnostic System Software (DSS)
This combines the operating modes “Continuous Gas Measurement” and “Continuous Turbidity
Mea surement”.
Click on Diagnostic Emission analysisGas & Opacity .
„Continuous Gas Measurement“ and chapter 3.1.5.1.2 „ Continuous
Turbidity Measurement “.
3.1.5.1.4 Timing
Information
Timing measurements can be performed only with the AVL 480 DiLink hardware module !
Otto engine: Displays speed, ignition timing, dwell angle and oil temperature.
Diesel engine: Displays speed, diesel timing and oil temperature.
Click Diagnostics Exhaust emissions analysis Timing .
Select your engine (Otto engine/diesel engine) and click F8 Next .
The measurements will be shown.
F2 Sensor
F4 Timing
F6 Freeze
Select the sensor for the engine temperature measurement.
Manual input
Temperature sensor
EOBD
F8 Confirm
---
Enter the engine temperature.
---
Press F5 Connect to establish a connection to the OBD module.
Back to the measurement display.
"Freezes" the measurement display.
F6 Continue Back to continuous measurement.
F7 Record
F8 Log
Continuously records the measurements and writes them to a text file.
F7 Quit
Saves the results log.
F3 Identification
F4 Print
F5 Edit
Quits continuous measurement recording.
"Vehicle identification" will appear.
F8 Next Quits vehicle identification.
Prints the results log.
This is where you can edit the results log
(display workshop and vehicle data yes/no).
F5 Apply Quits results log editing.
<< Cancel
F6 Save Saves the results log in the internal database
(see also 3.1.7 "Results management").
F8 Next Back to continuous turbidity measurement.
Quits continuous turbidity measurement.
User Manual 3-27
Preparing for Measurement
3.1.5.1.5 File
AVL DiTEST DSS
„"File". Only the functions relevant to the "Exhaust emissions analysis" will appear here.
3.1.5.1.6 Extras
Please refer to 3.1.2 "Extras". Only the functions relevant to the "Exhaust emissions analysis" will
appear here.
3-28 User Manual
AVL DiTEST DSS
3.1.5.2 EOBD
Diagnostic System Software (DSS)
3.1.5.2.1 Overview of EOBD Modes
The available EOBD modes depend on the vehicle being tested!
Mode Name Description
1
2
3
4
5
6
7
8
9
Actual values
Freeze Frame
Reads out and displays the current exhaust-related engine operating data (=actual values).
The readiness code displays the status of the exhaust-related components.
Reads out the operating conditions that existed at the time of recording an exhaust-related error.
Reads out and displays the recorded exhaust-related error codes.
Read error memory
Delete error memory Deletes the exhaust-related error codes
Deletes the operating conditions under which an exhaust-related error was recorded.
Deletes the lambda probe values
Sets the readiness code to “not performed”
Deletes the display with the activated fault lamp MIL mileage.
Lambda probe values
Reads out and displays the lambda probe values.
Sporadic test values Reads out and displays the test values from non-continuously monitored, manufacturer-specific components such as catalytic converters, evaporative systems etc.
Sporadic error memory
Actuators
Reads out and displays sporadically occurring, exhaust-related errors.
This mode is not supported.
Vehicle information Reads out and displays the following information:
- Vehicle information
- Settings information
- Settings verification number
User Manual 3-29
Preparing for Measurement
3.1.5.2.2 Establishing a Connection
AVL DiTEST DSS
For these test procedures, the vehicle must be connected to the AVL OBD and the vehicle ignition must be turned on.
3.1.5.2.3 Mode 1 Actual Values
Click on DiagnosticEOBDMode 1 .
A connection with the vehicle will be established and the data will be read out.
All possible diagnostic data will be displayed; select the data you are interested in.
F8 Next Accepts your selection.
The selected values are presented .
F4 Print Measured values will be printed .
F7 Back Returns to the parameter selection .
F8 Next Exit Mode 1.
3.1.5.2.4 Mode 2 Freeze Frame
Click on DiagnosticEOBDMode 2 .
A connection with the vehicle will be established and the data will be read out.
All possible freeze frame data will be displayed; select the data you are interested in.
F2 Select Selects all data.
F3 Discard Discards data selection.
F8 Next Accepts your selection.
The selected freeze frame data are presented .
F4 Print Prints the selected freeze frame data .
F7 Back
F8 Weiter
Returns to the parameter selection
Exit Mode 2.
3.1.5.2.5 Mode 3 Read Error Memory
.
Click on DiagnosticEOBDMode 3 .
A connection with the vehicle will be established and all emission-related error codes will be read out.
F4 Print Error codes will be printed.
F8 Next Exit Mode 3.
3-30 User Manual
AVL DiTEST DSS
3.1.5.2.6 Mode 4 Delete Error Memory
Diagnostic System Software (DSS)
Click on DiagnosticEOBDMode 4 .
A connection with the vehicle will be established and all emission-related error codes will be read out.
F4 Print
F5 New
F8 Next
Deleted errors will be printed.
Clears the fault memory.
Exit Mode 4.
3.1.5.2.7 Mode 5 Lambda Probe Values
Click on DiagnosticEOBDMode 5 .
A connection with the vehicle will be established and the test results of the lambda probe monitoring will be read out.
F4 Print
F8 Next
Values of lambda sensores will be printed.
Exit Mode 5.
3.1.5.2.8 Mode 6 Sporadic Test Values
Click on DiagnosticEOBDMode 6 .
A connection with the vehicle will be established and all test results of non-continuously monitored systems will be read out.
F4 Print
F8 Next
Sporadic test data will be printed.
Exit Mode 6.
3.1.5.2.9 Mode 7 Sporadic Error Memory
Click on DiagnosticEOBDMode 7 .
Click on EOBDMode 7 .
A connection with the vehicle will be established and all test results of non-continuously monitored systems will be read out.
F4 Print
F8 Next
Sporadic errors will be printed.
Exit Mode 7.
3.1.5.2.10 Mode 8 Actuator Test
This mode is not supported.
3.1.5.2.11 Mode 9 Vehicle Information
Click on DiagnosticEOBDMode 9 .
A connection with the vehicle will be established and all vehicle information will be read out.
F8 Next Exit Mode 9.
User Manual 3-31
Preparing for Measurement
3.1.5.3 ECU Diagnosis
Click Diagnostics ECU diagnosis .
If installed, AVL DiTEST XDS 1000 will start.
Please see the AVL DiTEST XDS 1000 User Manual.
3.1.5.4 Measurement & testing
Click Diagnostics Measurement & testing .
The "Measurement & testing" application will start.
Please see the AVL SCOPE User Manual.
3.1.5.5 HV Safety
Click Diagnostics HV Safety .
The "HV Safety" application will start.
Please see the AVL SAFETY User Manual.
AVL DiTEST DSS
3-32 User Manual
AVL DiTEST DSS
3.1.6 Jobs
Diagnostic System Software (DSS)
In the Jobs area you will find the job services available on your device (asanetwork).
3.1.6.1 Asanetwork
To be able to operate AVL DiTEST DSS in a network, you need:
AWN-compatible commercial software.
An active network manager.
The corresponding network installation (cabling, connection sockets, wireless LAN).
Information
With asanetwork functionality enabled, all AU measurements performed without asanetwork job will be stored under “Send results”.
For more options, see Chapter 3.1.2.1.2
„asanetwork“.
Information
Observe the documentation of:
Your asanetwork program
Your commercial software
3.1.6.1.1 Taking On Jobs from asanetwork
Click on OrdersasanetworkSelect order .
Select the desired job by clicking on it.
Display only AU jobs:
If this item is enabled, then only AU jobs will be displayed.
F4 Refresh Refreshes the display of jobs.
F5 Release
Refreshing the display in the main application window of AU jobs may take a few seconds, depending on the network speed.
If there are problems with the asanetwork, jobs can “hang”.
That is, they are marked as if being processed by the AVL DiTEST DSS
(when this is not the case). Such jobs can be released by pressing F5 .
Accepts the selected Job. F8 Next
After performing the AU, the AVL DiTEST DSS automatically sends the AU results log back to the
asanetwork.
User Manual 3-33
Preparing for Measurement
3.1.6.1.2 Send Results to asanetwork
All AU results can be sent to asanetwork.
Click on OrdersasanetworkSend results .
A list may appear containing obsolete results.
You can either delete these obsolete results with F5 Yes or keep them with F8 No .
All unsent jobs will be displayed; select the job in question.
Individual jobs can be selected by checking a box.
F2 Choose
F3 Discard
F5 Delete
F6 Send
F8 Next
Selects all jobs.
Discards the selected jobs.
Deletes the selected jobs.
Sends the selected jobs to asanetwork.
Closes the function “Send Results to asanetwork”.
AVL DiTEST DSS
3-34 User Manual
AVL DiTEST DSS
3.1.7 Results Management
Diagnostic System Software (DSS)
You can view all logs according to the date of performance.
Fig. 3-9
Source:
Click on Results Management .
Select Local / Network / Saved Results.
Period: Select Day, Week, Month, Year or All.
You can flip forwards and backwards using the arrows.
Report type: Select Proof / Diagnosis Logs etc.
Search criteria: Choose between “None”, “Manufacturer” or “Licence number”.
In the Search text field, you can narrow the selection down further.
Return to Results Management with Quit .
Individual logs can be selected by checking a box.
F2 Choose
F3 Discard
F4 Print
F5 Delete
F6 Export
F7 Archive
<< Cancel
Selects all logs.
Discards the log selection.
Prints the selected logs.
Deletes the selected logs.
Exports the selected logs.
F5 Directory Opens a window to choose the save location.
Choose a location and then click
F8 Next Starts the export.
OK .
Archives the selected logs.
The archived logs will be deleted from the internal database.
F5 Directory Opens a window to choose the save location.
Choose a location and then click
F8 Next
Quits the results display.
OK
Starts the archiving.
.
User Manual 3-35
Preparing for Measurement
3.1.7.1 File
AVL DiTEST DSS
Please refer to Cap. 3.1.1
„File“. Only the functions relevant to "Results management" will appear.
3.1.7.2 Extras
Please refer to 3.1.2 "Extras". Only the functions relevant to "Results management" will appear.
3-36 User Manual
AVL DiTEST DSS
3.1.8 Service/ Maintenance
Diagnostic System Software (DSS)
This chapter gives tips for an initial on-site diagnosis of the AVL DiTEST DSS station.
Preparation for calibration and linearity testing can be performed by the end customer as well as by the qualified service company.
AVL SMOKE:
Service screen (parameters for self-diagnostics)
AVL GAS:
Service screen (parameters for self-diagnostics)
AVL AUX:
Service screen (parameters for self-diagnostics)
AVL OBD:
Service screen (parameters for self-diagnostics)
AVL HV Safety:
Service screen (parameters for self-diagnostics)
Information
Please refer to the relevant device manual for further information on the AVL DiTEST MDS hardware components.
System info:
Parameters for self-diagnosis, with and without connected devices
License information:
Display the licenses present on the dongle
3.1.8.1 Calibration Programs
Please refer to the chapter 3.1.4
„AU“.
User Manual 3-37
Preparing for Measurement
3.1.8.2 Service Screen AVL SMOKE
AVL DiTEST DSS
The service screen AVL SMOKE shows:
■ Device identification
■ Measurements
■ Status
■ Information on the turbidity measurement chamber
Click on Service/MaintenanceAVL SMOKEService Screen .
The message “Initializing the diesel measurement chamber” appears shortly.
A service screen with parameters for self-diagnostics is shown.
(1)
(2)
(3)
Fig. 3-10 Example Servicescreen AVL DiSmoke 480
(1)
(2)
This field displays the connection and device status as well as various version numbers and serial numbers.
Here you can perform various functional checks
Valve position: Calibration, measurement
Lamp status: lamp A and B ON, lamps OFF, lamp A ON, and lamp B ON
Fan status: Automatic, ON
Heater status: Automatic, ON
Linearity test: The linearity error is measured and then shown.
Description of automatic procedure:
1. A lamp is measured.
2. Lamp B is measured.
3. A plus lamp bulb B is measured.
4. Comparison of point 3 with the sum of point 1 and point 2.
Initialization: AVL SMOKE will be re-initialized.
(3) This field displays the device-internal measurements.
F4 Report Displays a log. This can also be subsequently printed out.
3-38 User Manual
AVL DiTEST DSS
3.1.8.3 Service Screen AVL GAS
Diagnostic System Software (DSS)
Click on Service/MaintenanceAVL GASService Screen .
A service screen with parameters for self-diagnostics is shown.
(2)
(1)
(3)
(4)
Fig. 3-11 Example AVL Gas 1000
(1)
(2)
(3)
This field displays the connection and device status as well as various version numbers and serial numbers.
This field displays the status of the AVL DiTEST Gas 1000 (e.g.: stabilization necessary, leak test necessary…)
Here you can perform the functions: initialize (stabilization and HC residue test will be performed), gas measurement, leak test, condensation pump (on/off), gas pump (on/off)
(4)
F4 Report and valve (gas/fresh air).
When gas measurement is active, the measured values will be displayed in this field.
Displays a log. This can also be subsequently printed out.
F5 O2 sensor Initializes the O
2
sensor.
F6 Calibration
F8 Next
Test gas adjustment: The test gas adjustment is password-protected.
Refer to AVL DiTEST Service if necessary.
Swaps to further status displays.
User Manual 3-39
Preparing for Measurement
Status displays
Example AVL Gas 1000 Fig. 3-12
F7 Back
F8 Next
One step back.
Swaps to further status displays.
AVL DiTEST DSS
3-40 User Manual
AVL DiTEST DSS
3.1.8.4 Service Screen AVL AUX
Diagnostic System Software (DSS)
The AVL AUX service screen displays:
Connection and device status
Measurements
Speed measurement configuration
Click on Service/MaintenanceAVL AUXService Screen .
(1)
(2)
(3)
Fig. 3-13 Example AVL AUX 1000
(1) This field displays the connection and device status and various version numbers and
(2) serial numbers.
This field displays the speed and oil temperature.
(3) Switch between DiSpeed "Internal/External".
DiSpeed "internal" selection: „truck", "car", "2/4-stroke motorcycle".
F4 Report Shows a print preview of the service screen.
User Manual 3-41
Preparing for Measurement
3.1.8.5 Service Screen AVL OBD
The AVL OBD service screen displays the connection status of the scan tool used.
Click on Service/MaintenanceAVL OBDService Screen .
(1)
(2)
(3)
AVL DiTEST DSS
Fig. 3-14 Example AVL OBD
In the case of error, the following appear:
(1)
(2)
(3)
F8 Next
Connection status: PC Scantool Vehicle
Notes on the connection status
Scan tool used, Status of the scan tool used
Quits the function.
3-42 User Manual
AVL DiTEST DSS
3.1.8.6 Service Screen AVL HV Safety
The AVL HV Safety service screen displays:
Communication status
Device status
Firmware version
Firmware checksum
Boot loader version
Serial number
COM port used
Click on Service/Maintenance AVL HV Safety Service screen .
Abb. 3-15
F4 Log
Example AVL DiTEST HV Safety 1000
Displays a print preview of the service screen.
F5 Self-test Launches an AVL HV Safety self-test.
Diagnostic System Software (DSS)
User Manual 3-43
Preparing for Measurement
3.1.8.7 System Info
This shows:
■ Product information
- Installed programs
- Program versions
- Program versions of the connected components
■ Settings
- Input values that have been entered under “Tools”, “Settings”.
Click on Service/MaintenanceSystem Infowith devices or without devices .
The AVL DiTEST DSS system information will be displayed.
Fig. 3-16 Example
F4 Print
F8 Next
Prints a log of the system information.
Quits this function.
AVL DiTEST DSS
3-44 User Manual
AVL DiTEST DSS
3.1.8.8 License Information
The license information present on the dongle is displayed.
Click on Service/MaintenanceLicense information .
The license information present on the dongle will be displayed.
Fig. 3-17 Example
F4 Print
F8 Next
Prints a log of the license information.
Quits this function.
Diagnostic System Software (DSS)
User Manual 3-45
Preparing for Measurement AVL DiTEST DSS
3-46 User Manual
AVL DiTEST CDS
4 Maintenance
Maintenance
4.1 Maintenance Plan AVL GAS
Refer to user manual AVL DiTEST Gas 1000, Chapter 5.1 Maintenance Plan or the user manual
AVL DiTEST DiGas 480, chap. 5.1 Maintenance Schedule.
4.2 Maintenance
Plan
AVL SMOKE
Refer to user manual AVL DiSmoke 480 BT, Chapter 3.1 Maintenance Plan.
4.3 Maintenance AVL AUX
Make sure that the housing, the sockets and the Bluetooth aerial are neither damaged nor dirty.
4.4 Maintenance AVL SCOPE
Make sure that the housing, the USB cable and the BNC sockets are neither damaged nor dirty.
4.5 Maintenance AVL HV Safety
Make sure that the housing, the USB cable and the measurement cables/measurement adapters are neither damaged nor dirty.
4.6 Software update
Please refer to AVL DSS Installation and Updates, AVL ID no. AT7260ML.
This can be found in the DVD sleeve
User Manual 4-1
Maintenance AVL DiTEST CDS
4-2 User Manual
AVL DiTEST CDS
5 Index
A
Applications ....................................................... 3-12
Asanetwork ................................................. 3-4, 3-33
AU...................................................................... 3-21
Automatic Execution............................................ 3-6
AVL AUX ............................................................. 3-9
AVL DiGate 480 .................................................. 3-5
AVL GAS ........................................................... 3-11
AVL HV Safety .................................................... 3-9
AVL OBD ............................................................. 3-7
AVL SMOKE ...................................................... 3-10
B
Backup .............................................................. 3-18
Bluetooth ............................................................. 3-7
BMW Key Reader ................................................ 3-8
C
Calibration Programs......................................... 3-37
Close all applications........................................... 3-2
Continuous Gas & Opacity Measurement ......... 3-27
Continuous Gas Measurement ......................... 3-24
Continuous Opacity Measurement .................... 3-26
Customer Area .................................................. 3-19
Customer Management ..................................... 3-19
Customer/Vehicle Assignment .......................... 3-20
D
Data Recording ................................................... 3-6
Dateien exporting .............................................. 3-13
Device ............................................................... 3-16
Device connections .................................... 3-7, 3-17
Diagnostic .......................................................... 3-24
Diagnostic System Software (DSS) .................... 3-1
Diesel Values Display Program ......................... 3-22
DSS Application Window .................................... 1-2
DSS Manager ...................................................... 3-1
E
ECU Diagnose ................................................... 3-32
EOBD ................................................................ 3-29
Exhaust Analysis ............................................... 3-24
F
File ....................................................................... 3-2
Filtertest ............................................................. 3-22
G
Gas Values Display Program ............................ 3-23
General ....................................................... 1-1, 3-19
Index
H
HC Residue Test ................................................. 2-1
Help ..................................................................... 1-4
HV Safety ................................................. 3-12, 3-32
I
Infobox ................................................................. 1-4
J
Jobs ................................................................... 3-33
L
Language ............................................................. 3-3
Leak Test ............................................................. 2-1
License .............................................................. 3-14
License Information ........................................... 3-45
Log File .............................................................. 3-13
Logging ................................................................ 3-6
M
Maintenance ........................................................ 4-1
Maintenance AVL AUX ........................................ 4-1
Maintenance AVL HV Safety ............................... 4-1
Maintenance AVL SCOPE .................................. 4-1
Maintenance Plan AVL GAS ............................... 4-1
Maintenance Plan AVL SMOKE .......................... 4-1
Manufacturer Options ........................................ 3-12
Measurement & testing ..................................... 3-32
Mode 1 Actual Values ....................................... 3-30
Mode 2 Freeze Frame ....................................... 3-30
Mode 3 Read Error Memory .............................. 3-30
Mode 4 Delete Error Memory ............................ 3-31
Mode 5 Lambda Probe Values .......................... 3-31
Mode 6 Sporadic Test Values ........................... 3-31
Mode 7 Sporadic Error Memory ........................ 3-31
Mode 9 Vehicle Information ............................... 3-31
O
Operation ............................................................. 1-2
P
Preparing for Measurement ................................. 2-1
Q
Quit ...................................................................... 3-2
Quitting and switching off the application ............ 1-4
User Manual 5-1
Index
R
Restore .............................................................. 3-18
Results Management ........................................ 3-35
S
Send Results to asanetwork ............................. 3-34
Service Screen AVL AUX .................................. 3-41
Service Screen AVL GAS ................................. 3-39
Service Screen AVL HV Safety ......................... 3-43
Service Screen AVL OBD ................................. 3-42
Service Screen AVL SMOKE ............................ 3-38
Service/ Maintenance ........................................ 3-37
Settings ............................................................... 3-3
Show Log File .................................................... 3-13
Softwareupdate ................................................... 4-1
Stability Test ........................................................ 2-2
Stop devices ........................................................ 3-2
Summarized Safety Notices ................................... III
Switching on ........................................................ 1-4
System Info ....................................................... 3-44
System-Update .................................................. 3-14
AVL DiTEST CDS
T
Taking On Jobs from asanetwork ...................... 3-33
Timing ................................................................ 3-27
Tools .................................................................... 3-3
U
User Prompts ....................................................... 1-3
V
Vehicle Area ...................................................... 3-20
Vehicle Data ...................................................... 3-15
W
Warm-Up Phase .................................................. 2-2
Warn- und Sicherheitshinweise ............................... I
Workshop ............................................................ 3-5
5-2 User Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project