Fane EN21501 Enclosure.indd
,00
ø81
50
68,
,00
240 0
0
80,
0
2,0
,00
229
ø35
,00
ø81
116
0,0
0
,00
298 00
80,
0
2,0
230
,00
422
,00
ø35
FANE EN21501
2x 15” FULL RANGE ENCLOSURE
FANE COMPONENT OPTIONS
SOVEREIGN PRO 15-600LF | 15” Bass Driver
SOVERIGN PRO 15-500 | 15” Bass Driver
CD-150 | 1” Compression Driver
ELH003 | Fane Horn Flare
WWW.FANE-INTERNATIONAL.COM
FANE EN21501
2x 15” SUB BASS ENCLOSURE
Hints and Tips
CHOICE OF TIMBER
We recommend multi-layer 18mm Birch plywood as the best material to
withstand the rigours of intensive ‘life on the road’ or likely exposure to
damp conditions. Alternatively, 18mm Medium Density Fibreboard (MDF)
offers good acoustic properties with the advantage of being less expensive
(although heavier ), and may be used where the cabinet will be permanently
installed in a dry environment. Both materials accept any type of paint finish
extremely well.
CONSTRUCTION TECHNIQUE
All joints should be totally airtight, liberally glued with PVA adhesive and
screwed at 200mm (8”) centres with 4.2mm or 4.8mm (No.8 or No.10) x
50 mm (2”) self-tapping screws. The bracing panels are designed to ensure
rigidity of construction, making the cabinet as free as possible from panel
resonances caused by the internal forces generated by the loudspeaker drive
unit and resulting in unwanted vibration and colouration of the sound. Again,
these joints should be glued and screwed using the same method.
PORTING
The length and area of the ports as specified in the drawing should be strictly
adhered to.
ACOUSTIC INSULATION
To aid panel damping and prevent internal reflections and standing waves, all
internal panels of the cabinet ( with the exception of the front baffle ) should
be lagged with acoustically absorptive material. We recommend the use of
acoustic foam wadding. This should be glued, stapled or tacked to the inside
of the cabinet, taking care to ensure that port tubes are not obstructed
CROSSOVER NETWORK
Superb performance can be achieved when used with appropriately matched
custom designed passive crossover networks. The recommended Fane
crossover network components should be mounted as far away as practical
from the magnets. Major damage to both the crossover and drive units could
result should the board become loose during transit, therefore the crossover
should be mounted firmly to an inside wall of the cabinet, ideally secured using self-tapping screws in screw cups to reduce the pressure exerted on the
circuit board, and spaced with rubber grommets between the circuit board
and cabinet wall. It must however be pointed out that due to the very high
power handling capabilities of these drive units, some users may wish to employ an active crossover in order to utilise the full potential of these drivers.
INTERNAL WIRING
Wiring should be kept away from moving loudspeaker parts and fastened to
internal panelling to avoid buzzing. We encourage the use of colour coded
wiring to identify polarity (red for +ve and black for -ve), and recommend
carrying out a phase check before first using the cabinet. This is achieved by
applying the positive terminal of a battery to the positive cabinet input which
should result in the speaker cone moving forwards if in phase (or by using a
dedicated polarity checker).
DRIVE UNIT FIXING
The drive unit should be front mounted to the baffle using T-nuts and fixing
bolts, and is supplied with a length of self adhesive foam sealing strip which
should be fitted around the front edge of the speaker cut-outs to guarantee
airtight conditions.
LOUDSPEAKER PROTECTION
The exposed front of all speaker drive units is of course vulnerable to
damage, necessitating some means of protection which must be robust
but acoustically transparent. Cloth/foam type grilles are feasible for fixed
cabinets, but a metal mesh grille is certainly the preferred and superior
option. It is recommended that a foam gasket material is used between the
wooden cabinet and the metal grille to prevent any unwanted resonances.
Please contact Penn Elcom at www.penn-elcom.com to discuss their
standard and custom speaker grill solutions.
CABINET HARDWARE
We specify Penn-Elcom hardware products as recommend components in
the construction of FANE-loaded cabinets. Please visit www.penn-elcom.
com to view the full range of Penn Elcom products and discuss standard and
custom hardware solutions
CABINET FINISHING
Cabinet finishing is largely a matter of personal preference and as such,
detail of this is omitted from the drawing. Generally cabinets are either
painted or covered in carpet or vinyl material. If a carpet material is chosen
it is recommended that a very dense tight pile type is used and that metal
corner protectors are fitted. Corner protectors will have a defined radius
that the edges of the cabinet should be finished to. The cabinet shown on
the first page of this document has all the external edges routed with a
13mm radius and coated in a hard wearing textured epoxy paint. Two steel
carrying handles have been fitted. There are various types of handles and
terminal panels available and again details of these have been omitted.
It is recommended that these be purchased and cutouts be made in an
appropriate position in the panels before final build. Be aware that handles
and terminals are not necessarily airtight, which will be detrimental
to performance but can be easily remedied using a silicone sealant or
polyurethane mastic to seal all joints. Contact Penn Elcom at www.pennelcom.com to discuss their spray coating, carpet and vinyl options
WARNING!
There are safety regulations regarding the installation of loudspeaker
systems. This document is intended as a guide to construct a suitable
acoustic enclosure for our components. Fane Acoustics can hold no
responsibility for the structural integrity of the finished system. The system
will be no stronger than the material it is made from and the joinery
techniques used to assemble it. Suspending the finished system will require
additional hanging hardware. There are companies who specialise in the
manufacture and correct use of this hardware. They are experts and must be
consulted if overhead suspension of the finished system is intended.
FANE INTERNATIONAL LTD.
Sovereign House
Gilcar Way
Wakefield Europort
Castleford WF10 5QS
United Kingdom
Tel:
+44 (0)1924 224618
Fax:
+44 (0)1924 899166
Email: [email protected]
www.fane-international.com
Fane International Ltd operates a policy of continuous product development and reserves the right to
change specification at any time without notice. Any specifications or product images in this document
are correct at the time of print. © 2011, Fane International Ltd.
450,00
380,00
208,00
15,00
60,00°
4
2,7 3
5,4
24
146,00
25
150,00
240,00
80,00
ø81,00
99,0
339,55
0°
162,00°
99,00°
173,80
167,32
78,00°
78,00°
229,00
391,09
391,09
68,50
102,00°
68,50
209,84
196,05
60,00°
ø352,00
18,00
25,00
396,04
403,69
1160,00
78,00°
196,05
298,00
80,00
36,13
120,00°
ø81,00
400,00
230,00
102,00°
132,79
422,00
85,02
ø352,00
78,00°
78,00°
450,00
MODEL
FANE EN21501 - 2x 15” FULL RANGE ENCLOSURE
REVISION
1.0
SCALE
1:1
MATERIAL / FINISH
UNITS
mm
Tolerance Linear +/- 0.4, Holes +0.1/-0.0, None - Cumulative
Unspecified material. 15mm Birch Plywood, Baffle 18mm MDF
222,00
170,00
162,00°
THE PROFESSIONAL SERIES
SOVEREIGN PRO 15-600LF
BASS DRIVER
15” / 381 mm
600 w (A.E.S.)
CHASSIS DIAMETER
POWER HANDLING
35 Hz - 3.5 kHz
3.0” / 76.2 mm
COPPER VOICE COIL
FREQUENCY RESPONSE
FREQUENCY RESPONSE DATA*
• UK manufactured cone with optimised pulp offering increased strength,
durability and performance.
8Ω
+80
+70
600 w (A.E.S.)
Peak Power (6dB Crest Factor)
2400 w (A.E.S.)
Usable Frequency Range -6dB
35 Hz - 3.5 kHz
Sensitivity (1 w - 1 m)
+60
98 dB
Moving Mass inc. Air Load
20
50
100
200
1k
500
2k
5k
10k
20k
Hz
89 grams
Minimum Impedance Zmin
6.5 Ω
Effective Piston Diameter
* Half space response measured in a 975 litre sealed box.
13.03” / 330.96 mm
Peak Displacement Volume of Cone Vd
IMPEDANCE
0.59 litres
Magnet Weight
200
100
100 oz
Magnetic Gap Depth
0.39” / 10 mm
Flux Density
50
1.1 Tesla
20
Coil Winding Height
0.75” / 19 mm
10
Voice Coil Diameter
3.0” / 76.2 mm
FS Hz
40 Hz
RE Ohms
6.5 Ω
Qms
8.8
Qes
0.38
Qts
0.37
Vas Ltr
188 litres
Vd litres
0.59 litres
CMS (mm/N)
0.18 mm/N
BL T/m
19.7 T/m
Mms (grms)
89 grams
Xmax (mm)
6.9 mm
Sd (cm2)
856 cm2
Efficiency %
3.05%
Le (1k Hz)
1.85 mH
5
2
MOUNTING / SHIPPING INFORMATION
1
Overall Diameter
20
50
100
200
1k
500
2k
5k
10k
20k
Hz
Width Across Flats
Flange Height
PREDICTED BASS RESPONSE
+6
Baffle Hole Diameter R/M
14” / 355.6 mm
-24
Depth
-30
-36
5
10
50
100
1k
500
5k
10k
Hz
20k
Weight
Recommended Enclosure Volume
** Normalised bass response in 175 litre tuned to 40 Hz
m
Shipping Weight
”/
40
6.
4
m
Packing Carton Dimensions
6.85” / 174 mm
15.25” / 387.35 mm
8.22” / 209 mm
16
dB
Fixing Holes
-18
0.30” / 7.62 mm
13.85” / 351.79 mm
-6
-12
15.25” / 387.35 mm
Baffle Hole Diameter F/M
Gasket Supplied
0
MATERIALS OF CONSTRUCTION
16” / 406.4 mm
Front & Rear
4x 0.281” diam on 15.5 PCD
/ 8 x 0.281 diam on 14.56
PCD 4x 7.1 mm diam on
393.7 PCD / 8x 7.1 diam on
370 PCD
6.85” / 174 mm
Former Material
Voice Coil
Magnet Material
Chassis
Cone
Surround / Edge Termination
Glass Fibre
Copper
Ferrite
Die-cast Aluminium
Curvilinear Paper
Polyvinyl Damped Multi Roll. Poly
Cotton
Dust Dome
Paper
Connectors
Push-button Spring Terminals
Polarity
Positive voltage at red terminal
causes forward motion of cone
20.49 lb / 9.3 kg
2.64 - 5.29 cu ft / 75 - 150
litres
23.03 lb / 10.45 kg
220 x 420 x 420 mm
• Please enquire about alternative impedances.
• A.E.S. power handling test. Pink noise bandpass filtered at 12 dB per octave with cutoff frequencies of 40 Hz and 400 Hz. Driver mounted in
free air, test signal applied at rated power for two hours.
• Please note that the frequency response measurements are supplied for comparison only and are not a measure of the low frequency
performance which may be achieved in a fully optimised system.
| SOVEREIGN PRO 15-600LF
Power Handling
+90
THIELE SMALL PARAMETERS
15” / 381 mm
Impedance
+100
dBr
• Delivers tight accurate bass down to 40 Hz.
Nominal Chassis Diameter
+110
Ohms
• Smooth frequency response.
ELECTRO ACOUSTIC SPECIFICATIONS
+120
+50
• Highly versatile in 2-way ported enclosures.
THE PROFESSIONAL SERIES
The Sovereign Pro 15-600LF is intended for use in two-way ported enclosures, such
as the classic bass driver plus horn tweeter or compression driver format. The unit
features a die cast chassis with long throw motor system and long throw surround
allowing solid bass reproduction at high-power levels. The driver exhibits a smooth
frequency response to give a balanced tonal characteristic when properly matched
to appropriate high-frequency drivers. The Sovereign Pro 15-600LF can also be
used in ported bass enclosures to deliver tight accurate bass down to 40 Hz. The
unit features a 3-inch voice coil with a power handling of 600 Watts and an average
sensitivity of 98 dB.
98 dB
SENSITIVITY (1w / 1m)
THE PROFESSIONAL SERIES
SOVEREIGN PRO 15-500
BASS DRIVER
15” / 381 mm
500 w (A.E.S.)
POWER HANDLING
SENSITIVITY (1w / 1m)
42 Hz - 3.5 kHz
3.0” / 76.2 mm
Designed for use in 75150 litre enclosures
COPPER VOICE COIL
FREQUENCY RESPONSE
FREQUENCY RESPONSE DATA*
• High linearity suspension.
• UK manufactured cone with optimised pulp offering increased strength,
durability and performance.
4 /8 /16 Ω
+80
+70
500 w (A.E.S.)
Peak Power (6dB Crest Factor)
2000 w (A.E.S.)
Usable Frequency Range -6dB
42 Hz - 3.5 kHz
Sensitivity (1 w - 1 m)
+60
99 dB
Moving Mass inc. Air Load
20
50
100
200
1k
500
2k
5k
10k
20k
Hz
85 grams
Minimum Impedance Zmin
6.5 Ω
Effective Piston Diameter
* Half space response measured in a 975 litre sealed box.
13.03” / 330.96 mm
Peak Displacement Volume of Cone Vd
IMPEDANCE
0.51 litres
Magnet Weight
200
100
80 oz
Magnetic Gap Depth
0.39” / 10 mm
Flux Density
50
1.0 Tesla
20
Coil Winding Height
0.70” / 18 mm
10
Voice Coil Diameter
3.0” / 76.2 mm
FS Hz
40 Hz
RE Ohms
5.4 Ω
Qms
10
Qes
0.33
Qts
0.32
Vas Ltr
192 litres
Vd litres
0.513 litres
CMS (mm/N)
0.186 mm/N
BL T/m
18.9 T/m
Mms (grms)
85 grams
Xmax (mm)
6 mm
Sd (cm2)
855 cm2
Efficiency %
3.60%
Le (1k Hz)
1.9 mH
5
2
MOUNTING / SHIPPING INFORMATION
1
Overall Diameter
20
50
100
200
1k
500
2k
5k
10k
20k
Hz
Width Across Flats
Flange Height
PREDICTED BASS RESPONSE
+6
Baffle Hole Diameter R/M
14” / 355.6 mm
-24
Depth
-30
-36
5
10
50
100
1k
500
5k
10k
Hz
20k
Weight
Recommended Enclosure Volume
** Normalised bass response in 175 litre tuned to 40 Hz
m
Shipping Weight
”/
40
6.
4
m
Packing Carton Dimensions
6.37” / 162 mm
15.25” / 387.35 mm
7.79” / 381 mm
16
dB
Fixing Holes
-18
0.30” / 7.62 mm
13.85” / 351.79 mm
-6
-12
15.25” / 387.35 mm
Baffle Hole Diameter F/M
Gasket Supplied
0
MATERIALS OF CONSTRUCTION
16” / 406.4 mm
Front & Rear
4x 0.281” diam on 15.5 PCD
/ 8 x 0.281 diam on 14.56
PCD 4x 7.1 mm diam on
393.7 PCD / 8x 7.1 diam on
370 PCD
6.37” / 162 mm
Former Material
Voice Coil
Magnet Material
Chassis
Cone
Surround / Edge Termination
Glass Fibre
Copper
Ferrite
Die-cast Aluminium
Curvilinear Paper
Polyvinyl Damped Multi Roll. Poly
Cotton
Dust Dome
Solid Paper
Connectors
Push-button Spring Terminals
Polarity
Positive voltage at red terminal
causes forward motion of cone
17.52 lb / 7.95 kg
2.64 - 5.29 cu ft / 75 - 150
litres
20.05 lb / 9.1 kg
220 x 420 x 420 mm
• Please enquire about alternative impedances.
• A.E.S. power handling test. Pink noise bandpass filtered at 12 dB per octave with cutoff frequencies of 40 Hz and 400 Hz. Driver mounted in
free air, test signal applied at rated power for two hours.
• Please note that the frequency response measurements are supplied for comparison only and are not a measure of the low frequency
performance which may be achieved in a fully optimised system.
| SOVEREIGN PRO 15-500
Power Handling
+90
THIELE SMALL PARAMETERS
15” / 381 mm
Impedance
+100
dBr
• Smooth extended frequency response.
Nominal Chassis Diameter
+110
Ohms
• High SPL producing fast and punchy bass.
ELECTRO ACOUSTIC SPECIFICATIONS
+120
+50
• Highly versatile in 2-way ported enclosures.
THE PROFESSIONAL SERIES
The Sovereign Pro 15-500 is intended for use in two-way ported enclosures, such
as the classic bass driver plus horn tweeter or compression driver format. The unit
features a die cast chassis with long throw motor system and high linearity suspension
allowing solid bass reproduction at high-power levels. The driver exhibits smooth
frequency response to give a balanced tonal characteristic when properly matched to
appropriate high-frequency drivers. The Sovereign Pro 15-500 is designed for use in
75 to 150 litre ported enclosures. The unit features a 3-inch voice coil with a power
handling of 500 Watts and an average sensitivity of 99dB.
99 dB
CHASSIS DIAMETER
THE HIGH FREQUENCY DEVICES SERIES
CD-150
COMPRESSION DRIVER
1” / 25.4 mm
50 w (A.E.S.)
SOUND CHANNEL / THROAT SIZE
POWER HANDLING
2 kHz - 18 kHz
1.75” / 44 mm
FREQUENCY RESPONSE
Aluminium Voice Coil
The CD150 is an excellent choice for professionals who are looking to achieve high
sound pressure level performance and clarity of sound. The unit combines high BL
and a lightweight diaphragm assembly to produce a very high output device that
also features extended bandwidth and well defined frequency response. The CD150
is optimised for high performance multi-way system designs. The driver has a rated
low frequency response limit of 2.2 kHz and features extended response to 20kHz.
The ferrite based permanent magnetic system produces a very high efficiency to
weight and size ratio. The compression driver exit diameter and fixings are an industry
standard and will match to commercially available high frequency horns. This makes
the CD150 ideal for high level professional touring applications as well as high level
fixed installation.
• 1” exit ferrite magnet compression driver.
FREQUENCY RESPONSE DATA*
IMPEDANCE
• Titanium diaphragm with double sinusoidal roll surround (titanium).
• 50 Wrms (AES standard)
• Copper inductance ring for extended response.
• Ferrofluid cooled
• Also available for OEMs with an aluminium diaphragm option.
200
100
+110
20
Ohms
+90
dBr
| CD-150
50
+100
+80
10
+70
5
+60
2
500
1k
2k
10k
5k
20k
1
20
50
100
200
Hz
Sound Channel / Throat Size
Nominal Impedance
Power Handling
Sensitivity (1 w - 1 m)
Usable Frequency Range -6dB
Recommended Crossover Frequency
Filtered at 18dB / Octave
MOUNTING / SHIPPING INFORMATION
1” / 25.4 mm
8 /16 Ω
50 w (A.E.S.)
106 dB
2 kHz - 18 kHz
3.5 kHz
Effective Diaphragm Diameter
1.75” / 44 mm
Voice Coil Diameter
1.75” / 44 mm
Voice Coil DC Resistance
Max Diaphragm Displacement
Magnet Weight
500
1k
2k
5k
10k
20k
Hz
ELECTRO ACOUSTIC SPECIFICATIONS
Flux Density
HIGH FREQUENCY DEVICES
• 1.75” / 43mm copper clad aluminium voice coil.
+120
+50
300
106 dB
SENSITIVITY (1w / 1m)
Overall Diameter
MATERIALS OF CONSTRUCTION
Coil Former
Polyamide
Depth
2.48” / 63 mm
Voice Coil Material
Aluminium
Weight
6.5 lb / 2.97 kg
Diaphragm Material
5.27” / 133.85 mm
Shipping Weight
6.8 lb / 3.1 kg
Packing Carton Dimensions
150 x 160 x 180 mm
Bolt Fixing Hole Dimensions
& Qty
2x M6 on 72.2 mm - 3” PCD
6.2 / 10.5 Ω
0.016” / 0.4 mm
1.65 Tesla
39 oz
• Please enquire about alternative impedances.
• Frequency response measurement taken on axis with 1w signal at distance of 1m using custom horn with 90° x 40° coverage.
Surround / Edge Termination
Magnet Material
Connectors
Polarity
Titanium
Double Sinusoidal Roll Titanium
Ferrite
4.8 mm Spade
Positive voltage at red/ positive
terminal causes positive pressure
at throat exit
FANE EN21501
ADDITIONAL COMPONENTS
ELH-003
•
•
•
Eliptic Horn Nominal Directivity
80° x 60°
Loading down to1000 Hz
Strong Glass Fibre material
Perfectly Controlled Dispersion
ELECTRO ACOUSTIC SPECIFICATIONS
MOUNTING / SHIPPING INFORMATION
Sound Channel / Throat Size
Nominal Coverage (-6dB)
Cut-off Frequency
Material
Overall Dimensions
Baffle Cut Out
1” / 25.4 mm
80 x 60
1000 Hz
Glass fibre resin
ELECTRO ACOUSTIC SPECIFICATIONS
Sound Channel / Throat Size
Nominal Coverage (-6dB)
Cut-off Frequency
Material
1” / 25.4 mm
80 x 60
1000 Hz
Glass fibre resin
Total Depth
Fixing Holes
Net Weight
Shipping weight
240 x 180 mm
Minor Rad. 75 mm
Major Rad. 104 mm
115.5 mm
4 x 6 mm holes 101/76 mm
0.9 kg
1.3 kg
PENN - M1702 PORT TUBE (x4)
ELECTRO ACOUSTIC SPECIFICATIONS
Diameter
Material
Finish
Weight
75 mm / 2.95”
Plastic
Black
0.058 Kg / 0.13 lb
FANE CROSSOVER EN21501
FREQUENCY RESPONSE DATA
120
110
dB SPL
•
100
90
80
100
1k
10k
Frequency Hz
Frequency response curve of the horn measured on
axis at distance of 1 meter with1 watt signal
with CD-140 compression driver.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement