null  null
ADDENDUM A
GENERIC SPECIFICATION FOR MATERIALS AND FINISHES:
General preambles:
1. TRADE NAMES: All materials, fittings and finishes specified may be
replaced by equal and approved alternatives.
2. Samples - With reference to all items and colour schemes: Samples off all items are to be
presented for approval prior to any bulk orders. Please take note that most items will have at
least six week delivery period, these approvals will only take place at dates off site meetings, the
samples need to be approved well in advance to avoid any delays with lead time on orders. All
samples must remain in the sample room for the duration of the contract.
3. Mock up rooms – all wall and floor finishes must be prepared in advance as part of a mock up
room/rooms and at least a 100 square meter of vinyl flooring will serve as a sample floor.
4. Samples - All samples submitted for approval, must be accompanied with the relevant
Architects specifications for approval. (extract from specifications)
Revision R02 :
Added A33
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
FINISHES - EXTERIOR (A)
A01. Steel metal roof covering :
Clotan Steel Craft-Lock profile 0,58mm thick ISQ300 Z600 spelter galvanised steel roof sheeting, flashing and accessories
(unfinished) as by manufacturer fixed to roof structure (to Engineer's detail) at centres as specified by manufacturer. (Also
see Roof plan)
A02. Trafficable waterproofing :
Waterproofing to exposed concrete roofs (to Engineer's detail) with bituminous aluminium paint finish and stone. Apply
one coat a.b.e. bituprime to all surfaces including all verges and around outlets and protrusions on screed to fall. Screed to
have a minimum thickness of 25mm.
Apply one layer of a.b.e. 4mm abegum dual reinforced waterproofing membrane, fully bonded by means of "torch fusion",
with 75mm side laps and 100mm end laps. Apply one coat of a.b.e silvakote bituminous aluminium protective coating.
Flashing strip 150mm girth at turn-ups using a.b.e. auper laycryl.
Dress surface evenly with 19mm washed crushed stone dressing to a depth of 50mm in accordance with waterproofing
manufacturer's specification.
Flood tests to be done on completion in workman like manner.
A03. External plaster and paint finish (smooth) :
Plaster mix for approved rough brick / concrete walls, composed of 1 part cement and 6 parts sand, +/- 12mm thick
finished with a wood float to receive high quality paint / wall coating. All to cover surface sufficiently.
Finish with Plascon Wall & All to exterior new cement plaster (NW 100) - strictly according to manufacturer's specification.
Surface to be dry, sound and clean and cured for a minimum of 14 days. Prime with one coat of Plascon Primer (UC56)
with an overcoating time of 16 hours and finish with two coats of Wall & All (WAA 1) with minimum 2 hours drying time
between coats. Colours to Architect's approval.
A04. Window cills (External) :
Modcon Concrete Solutions precast concrete window sill (Type: 005), overall size 160 x 110mm high, bedded and jointed
in Class II mortar and pointed on all exposed faces. complete with damp proof course installed to manufacturer's
specification
A05. Steel roof structure
Plascon Glatex 8 to exterior new mild steel.
Surface to be clean and dry. Remove surface contaminants using Metalcare Aquasolv Degreaser (GR 1) with bristle brush
or Brillo pads. Rinse thoroughly with tap water until surface is water break-free. Remove rust and millscale by abrasive
blasting to ISO 8501 - 01:1988 - Sa2½ or by hand/mechanical wire brushing to St3 of the same standard. Allow to dry
completely and prime within 4 hours of cleaning. Prime with one coat Glatex 8 Metal Primer (PL 3) with an overcoating
time of 8 hours and finish with two coats Glatex 8 (PL) with 16 hours drying time between coats, for a maintenance cycle
of 10 years.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
A06. Paving (bricks) :
Corobrik® 38MPa Paver PA clay paving bricks - colours to Architect's approval, size 220 x 108,5 x 50mm thick ,
manufactured in accordance with SANS 1575:2007, laid in Herringbone Bond pattern with a minimum longitudinal fall of
1% on a transverse fall of at least 2% on 25mm compacted sand bed with fine jointing sand swept and vibrated into joints,
all laid on subgrade conforming to SANS 1200 D Degree Of Accuracy I. Paving to be inspected and re-sanded after three
months. Paving to be inspected and re-sanded after three months.
A07. Concrete blocks :
Standard 190 x 190 x 190mm concrete grille blocks as by Watson Concrete or similar approved with 10mm square
recessed joints in both directions. Install to manufacturer's specification.
A08. Tree ring :
Modcon Concrete Solutions Type 001 precast concrete tree ring, size 1060mm diameter x 205mm high, bedded and
jointed in Class II mortar and pointed on all exposed faces.
A09. Face brick Walls :
Face brick walls to dimensions as on plan - colour, bond and type to Architect's approval, bedded and jointed in Class II
mortar, pointed with 10mm square recessed joints in both directions, manufactured in accordance with SANS277:2007.
A10. Windows :
Purpose-made aluminium frame windows and glazing as per window schedule
A11. Doors :
All doors and ironmongery as per door schedule
A12. Sun louvres :
Hunter Douglas or similar approved vertical aluminium sun louvre system (with UV protective coat) consisting of anodised
aluminium panels (colour to Architect's approval) fixed to supports fitted to building structure, all to manufacturer's detail
and specification. The entire system to be designed and installed by approved specialist, all in accordance with the
manufacturer's recommendations.
A13. Exposed steelwork :
Purpose made hot dipped galvanised mild steel sections, all according to Structural Engineer's detail drawings. All to
Architect's approval.
A14. Decorative louvre screens :
Hunter Douglas or similar approved vertical fixed decorative louvre system, panels to receive 60µm Luxacote® finish
colour to Architect's approval, fixed to fascade of building as per manufacturer's detail and specification. The entire
system to be designed and installed by approved specialist, all in accordance with the manufacturer's recommendations.
A15.Off-shutter concrete :
Off-shutter R.C column and beams according to Structural Engineers detail design, with specialist designed shuttering as
by PERI (011- 3101010) – Patterns and shutter type to Architects approval.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
A16. Decorative plaster :
Plaster mix for rough brick/concrete walls, composed of 1 part Surebuild cement (Code: CEM II/B 32.5R) and 6 parts sand,
±12mm thick finished in one operation with ROUGH CAST machine to walls to receive high quality paint/ wall coating.
Surebuild cement is to be manufactured in accordance with SANS 50197-1. All to manufacturer’s specifications to cover
surface sufficiently .
Plascon Wall & All to exterior new cement plaster (NW 100). Colours to Architect’s approval.
Surface to be dry, sound and clean and cured for a minimum of 14 days, with a moisture content measured with a Doser
Hygrometer (or equivalent), of BD 2 scale - 8% or less. Prime with one coat of Plascon Plaster Primer (UC 56) with an
overcoating time of 16 hours and finish with two coats of Wall & All (WAA) with 2 hours drying time between coats, for a
maintenance cycle of 7 years in a C5 - coastal/marine environment. Colours to Architect’s approval.
A17. Pergola :
Purpose made mild steel pergola complete with fixing brackets and columns (all members to be hot dip galvanized) – all to
detail drawings. Surface to be dry, sound and clean. Apply Plascon Galvanized Iron Cleaner (GIC 1) to all bare galvanized
areas. Allow to react for 1 minute and rinse off with tap water using bristle brush or Scotch Brite pads to remove all
surface contaminants, until surface is water break-free. Prime with one coat of Galvanized Iron Primer (GIP 1) with an
overcoating time of 2 hours and finish with two coats of Nuroof Acrylic Roof Paint (TRP) with 1 hour drying time between
coats, for a maintenance cycle of 6 years in a C3 - industrial environment. Colour to Achitects approval.
A18. Steel balustrade :
Vital Engineering (Angus McLeod) Maclock light duty or similar approved, galvanised mild steel angle ball railings, code
MS L G tubular (all members to be hot dip galvanized), consisting of 1000mm high, 60 x 60 x 6mm ABTA35 stanchions
spaced at max. 1500mm centres, with 27mm Ø tubular hand/knee rails. Top mounted stanchions to be fitted with
baseplates pre-drilled with 30 x 18mm slotted holes for fixing to concrete/metal surface, including all necessary bends,
closures, ferrules etc. as indicated on drawings.
A19. Clearvu fencing :
Cochrane ClearVu high density anti-climbing and anti-cut pressed mesh panel fencing 2,1m high, formed of 3mm diameter
horizontal and 4mm diameter vertical high tensile wires galvanised with alu-galv coating with aperture size 76,2mm x
12,7mm and reinforcing V-section ribs, bolted with vandal resistant bolts and clamping plates to 85 - 45mm Taper locking
post 2,7m high including Locking Recess Mechanism at 3,382m centres with sealed end caps and 30 x 3mm x 250mm long
angle section base anchors with posts bedded in 15MPa concrete bases size 400 x 400 x 600mm deep.
A20. Concrete apron :
In-situ concrete apron/ storm water channel to dimensions as shown on plan, complete with falls. All to Civil Engineer’s
detail design.
A21. Roof flashing :
Global Roofing Solutions 0,80mm thick Z275 spelter ISQ550 galvanised steel, girth 375mm head- and sidewall flashing
(Code: FK8 and FK9), fixed in accordance with manufacturer's specifications.Install strictly to manufacturer’s specifications.
Colours (Non standard) to Architect’s approval.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
A22.Rain water downpipe :
Standard 100mmø mild steel rainwater downpipes fixed to walls with downpipe holder bats using nail-in anchor installed
and fixed strictly according to manufacturer's detail and specification
A23. 150mm. Gutters :
Purpose made 150x100mm. galvanized sheet metal gutters including rivet-fixed mitres and end caps internally sealed
using Silicon Mastic, hung by hangers with downpipes (elsewhere specified). Install strictly to manufacturer’s
specifications. Profile, type and finish all to Architect's approval.
A24. Rain water downpipe :
Standard 75mmø mild steel rainwater downpipes fixed to walls with downpipe holder bats using nail-in anchor installed
and fixed strictly according to manufacturer's detail and specification.
A25. Fascia gutter :
Global Roofing Solutions standard fascia gutter installed with concealed brackets and verandah bolts to the sheeting
through the concealed support clip pop riveted to the narrow flute of the sheeting at 1218mm centres. All as per
manufacturers specifications.
A26. Mild steel fascias :
Purpose made 1.6mm thick powder coated sheet metal fascia bend into profile complete with concealed fixings and drip
joints as shown on detail drawings. Colour to match roof sheeting.
A27. Roof isolation :
Super Sisalation® 400 double-sided reflective foil laminate incorporating layers of kraft paper and reinforcing scrim
laminated together with with low density polyethylene (217gsm), laid taut over steel purlins at centres as by manufacturer
and fixed concurrent with roof covering including galvanised steel straining wires. All in accordance with manufacturer's
and/or supplier's specifications and recommendations.
A28. Valley gutter :
Rectangular valley gutter to be Brownbuilt (011 - 898-2900) Klip-Lok 700 (girth to be stated), 0,8mm thick light industrial
Z275 spelter galvanised steel sheeting gutter, seven times bent along girth. Finish with Classicoat finish to one side and
half coat Classicoat Grey other side. Complete with metal and poly closer without any joints (If unavoidable min. 500mm
overlay, complete with sealing strips). Install strictly to manufacturer’s specifications. Colours to Architect’s approval.
A29. Apex flashing :
Apex flashing (Code FS5) to be Brownbuilt Custom-Orb 462mm girth, three times bent along girth and notched on site to
suit roof profile. Complete with metal and poly closer without any joints (If unavoidable min. 500mm overlay, complete
with sealing strips). Secured with hex head self drilling tek screws (with bonded washers) to purlins, all in accordance with
the manufacturer's recommendations. (Finish with Classicoat to both sides on covered walkways or when exposed to
bottom). Colours to Architect’s approval.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
A30. Exterior corner flashing :
Exterior corner trim flashing to be Brownbuilt Custom-Orb 462mm girth, four times bent along girth as per detail drawing.
Complete with metal and poly closer without any joints (If unavoidable min. 500mm overlay, complete with sealing strips).
Secured with hex head self drilling tek screws (with bonded washers) to purlins, all in accordance with the manufacturer's
recommendations. (Finish with Classicoat to both sides on covered walkways or when exposed to bottom). Colours to
Architect’s approval.
A31. Concrete coping :
Purpose made concrete coping to detail drawings as by WATCRETE or equal approved. Bed in 1:2 mortar with properly
filled and ruled joints. All to Architect’s approval. Plaster and paint to match wall.
A32. Turnstile :
Turnstar or similar approved ultra heavy duty Triumph 3 arm, full height, single electrical bi-directional turnstile in 304grade stainless steel finish, with 5 year guarantee, with Rotalok® rotation locking mechanism and Rotarun® perpetual base
bearing, all bolted to concrete slab (elsewhere specified) and connected to 220V power supply. Access control to electrical
engineers detail specifications. All installed strictly to manufacturers specifications. All to Architect's approval.
A33. 150 x 75mm. Gutters : R02
Purpose made 150x75mm. galvanized sheet metal gutters including rivet-fixed mitres and end caps internally sealed using
Silicon Mastic, hung by hangers with downpipes (elsewhere specified). Install strictly to manufacturer’s specifications.
Profile, type and finish all to Architect's approval
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
FINISHES - INTERIOR (B)
B01. Seamless Vinyl Floor Sheets :
FloorworX Superflex fully flexible vinyl floor sheeting 1,2m wide x 2,0mm thick, manufactured in accordance with SANS
786:2000, laid in FloorworX No. 62 acrylic adhesive spread with a Vicker A24F trowel at a rate of between 5.5m² and
6.5m² per litre on suitably prepared subfloor (as below) with a hygrometer reading showing a moisture content of less
than 70%, with joints welded with a fully flexible coloured 'FloorworX Welding Rod' to provide a smooth, hygienic sealed
finish and rolled with 68kg three section metal roller on completion. Colour of sheeting and welding rods to Architect's
approval.
Subfloor : Sheeting to be installed on a CFD/UZIN Premium system consisting of UZIN PE 260 primer, UZIN NC 160 selflevelling cementitious compound and UZIN KE 2000S adhesive as by Contract Flooring Distributors ( 011 882 1000/1/2)
with a 20+ years guarantee, all strictly according to manufacturer's specification, on reinforced concrete slab according to
Structural Engineer’s detail design.
NOTE :
a) Where applicable, all expansion joints in screed to be covered with FloorworX expansion joint cover strip, installed in
accordance with manufacturer's specifications. - Strip and welding rod colours to Architects approval.
b) Where floor covering change from one floor finish to another, the finishes should be divided with a 25mm x 3mm brass
dividing strip cast into screed at position as indicated on detail drawing (flush with floor finish).
c) Skirting to be similar to floor taken 200mm up against the wall, complete with FloorworX Extruda Black (Colour code:
MCF35) vinyl cove fillet size 26mm high, fixed with FloorworX No. 71 solvent based contact adhesive, spread with a brush
onto both material and working surface, FloorworX vinyl capping strip size 6 x 35mm high (colour to Architect's approval,
fixed with FloorworX No. 71 solvent based contact adhesive, spread with a brush onto both material and working surface.
Also including a taper end piece inserted 150 mms prior to the doorway. Glue to wall with an approved adhesive all in
accordance with manufacturer's specifications.
B02. Synthetic Rubber Floor :
FloorworX norament® 825 rubber floor tiles 501 x 501 x 3,2mm thick in 0702 finish (Colour code: 0702), laid in FloorworX
No. 55 polyurethane adhesive, spread according to manufacturer's recommendations on suitably prepared subfloor (as
per annotation B01) with a hygrometer reading showing a moisture content of less than 70% and rolled with 68kg three
section metal roller on completion.
NOTE :
a) Where applicable, all expansion joints in screed to be covered with FloorworX expansion joint cover strip, installed in
accordance with manufacturer's specifications. - Strip and welding rod colours to Architects approval.
b) Where floor covering change from one floor finish to another, the finishes should be divided with a 25mm x 3mm brass
dividing strip cast into screed at position as indicated on detail drawing (flush with floor finish).
c) Skirting to be similar to floor taken 200mm up against the wall, complete with FloorworX vinyl capping strip size 6 x
35mm high (colour to Architect's approval, fixed with FloorworX No. 71 solvent based contact adhesive, spread with a
brush onto both material and working surface, all in accordance with manufacturer's specifications.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
B03. Safety Vinyl Floor Sheets :
All wet areas to receive FloorworX surestep® fully flexible heavy duty floor sheeting 2m wide x 2,0mm thick, manufactured
in accordance with SANS 786:2000, laid in FloorworX No. 62 acrylic adhesive spread with a Vicker A24F trowel at a rate of
between 5.5m² and 6.5m² per litre on suitably prepared subfloor (as below) with a hygrometer reading showing a
moisture content of less than 70%, with joints welded with a fully flexible coloured 'FloorworX Welding Rod' to provide a
smooth, hygienic sealed finish and rolled with 68kg three section metal roller on completion. Colour of sheeting and
welding rods to Architect's approval.
Subfloor : Sheeting to be installed on a CFD/UZIN Premium system consisting of UZIN PE 260 primer, UZIN NC 160 selflevelling cementitious compound and UZIN KE 2000S adhesive as by Contract Flooring Distributors ( 011 882 1000/1/2)
with a 20+ years guarantee, all strictly according to manufacturer's specification, on reinforced concrete slab according to
Structural Engineer’s detail design.
NOTE :
a) Where applicable, all expansion joints in screed to be covered with FloorworX expansion joint cover strip, installed in
accordance with manufacturer's specifications. - Strip and welding rod colours to Architects approval.
b) Where floor covering change from one floor finish to another, the finishes should be divided with a 25mm x 3mm brass
dividing strip cast into screed at position as indicated on detail drawing (flush with floor finish).
c) Skirting to be similar to floor taken 200mm up against the wall, complete with FloorworX Extruda Black (Colour code:
MCF35) vinyl cove fillet size 26mm high, fixed with FloorworX No. 71 solvent based contact adhesive, spread with a brush
onto both material and working surface, FloorworX vinyl capping strip size 6 x 35mm high (colour to Architect's approval,
fixed with FloorworX No. 71 solvent based contact adhesive, spread with a brush onto both material and working surface.
Also including a taper end piece inserted 150 mms prior to the doorway. Glue to wall with an approved adhesive all in
accordance with manufacturer's specifications.
B04. Grano Floor :
± 30mm Thick Untinted cement screed with or without falls on concrete surface bed as by Engineer, finished with a power
float finish. The Surface should be free of oil, grease and other contaminants and loose dust and acid etching. Oil and
grease must be completely removed with Pro-Struct Degreaser Type 106 or 109 and allowed to dry thoroughly. Apply
three or more coats of Pro-Struct (011-254 5500) Floor Hardener Type 541 to ensure a universal substrate, allowing a
maximum of three hours between coats - installed by an approved applicator, strictly to manufacturers specifications.
Pre-approve sample.
NOTE :
a) Where floor covering change from one floor finish to another, the finishes should be divided with a 25mm x 3mm brass
dividing strip cast into screed at position as indicated on detail drawing (flush with floor finish).
b) Skirting to be 100mm high coved grano skirting
B05. Wood float Floor :
± 30mm Thick Untinted cement screed with or without falls on concrete surface bed as by Engineer, finished with a wood
float finish.
NOTE :
a) Skirting to be 100mm high coved grano skirting
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
B06. Window cills (Internal)
Plastered and painted (as per annotation B07) with rounded edge, except where tiles are specified on walls.
For tiled walls, window cill to be similar tiles cut to fit cill. Tiles and grouting to match walls
B07. Walls (Internal) :
Plascon Wall & All to interior new cement plaster.
Surface to be dry, sound and clean and cured for a minimum of 14 days. Prime with one coat Plascon Plaster Primer (UC
56) with an overcoating time of 16 hours and finish with two coats Wall & All (WAA 1) with 2 hours drying time between
coats, for a maintenance cycle of 7 years. Colour to Client's approval.
B08. Concrete ceilings :
Apply ±12mm thick cement plaster 1:4 mixture to ceilings (R.C. slab & beams) in one operation with steel trowel. Smooth
and prepare surfaces and remove all loose material, and rinse. Apply flexible crack filler to holes and cracks and finish as
per annotation I07. Colour to Client's approval.
B09. Suspended ceilings (1200 X 600 GYPREX) :
BPB Gypsum DonnCeill White vinyl finished gypsum ceiling tiles size 1200 x 600mm x 12,5mm thick, laminated to 55mm
thick glasswool insulation, laid on and including SQ/T38 White powder coated main tees, cross tees, hold-down clips,
wedges, etc., all suspended with galvanized hangers at hanger centers not exceeding 1200mm. All strictly in accordance
with the manufacturer's specifications and recommendations. Colour white.
Cornice : BPB gypsum 47 x 35mm SM25 plugged recessed shadowline cornice. Installed strictly to manufacturer's
specifications against wall or plastered ceiling bulkheads to detail elsewhere.
B10. Plastered ceilings and bulkheads :
GYPROC RhinoCeil Prestige J flush jointed ceiling 9,5mm thick Taper-edge Rhinoboard fixed print side up and screwed to
Donn T37K galvanised steel capped tee flush plastered ceiling suspension system with drywall screws spaced at 150mm
centres, including galvanised main tees at 1200mm centres and cross tees at 500mm centres, all suspended with 25 x
25mm galvanised angles at not exceeding 1200mm centres, all fixed to trusses at centres. Joints to be taped and finished
as per manufacturers instructions complete with SABISA certificate.Prepare surfaces and remove all loose material. Apply
one coat PLASCON Wall & All Pure Acrylic paint, thinned 20% and one coat PLASCON Wall & All Pure Acrylic paint to new
plaster board ceilings to cover surface sufficiently. Colours to Architect’s approval. Also refer to Ceiling Plan.
Cornice: GYPROC 45 x 35mm flush plaster trim (9,5mm thick) plugged. (Code 1972).
B11. Nutec ceilings :
Everite Nutec 4mm thick plain ceiling boards, manufactured in accordance with SANS 9001:2000 carrying SANS 803:2005
mark, screw fixed to battens at 150mm centres and according to manufacturer's specifications, minimum of 12mm from
edge of board. All joints to be covered using H-profile steel jointing strips, all in accordance with the manufacturer's
recommendations. Also refer to Ceiling Plan.
Cornice: GYPROC 45 x 35mm flush plaster trim (9,5mm thick) plugged. (Code 1972).
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
B12. Wall tiles :
Johnson or similar Gloss White glazed ceramic wall tiles, size 200 x 200mm, fixed to wood floated Class II mortar plaster
backing with approved tile adhesive mixed with bonding liquid in lieu of water, with 3mm joints continuous in both
directions grouted with tile grout (elsewhere specified) with minimum 5mm expansion joints at perimeter, all structural
expansion and construction joints and maximum 5m centres internally and at 3m centres externally, in both directions.
Tile walls to door height, except in Lab where 3x rows of tiles to be installed wherever worktop meets with wall
B13. Carpet tiles :
Van Dyck(031 912 1200) Florpoint medium commercial (SABS use class U4), 100% Polypropylene, 7mm thick needlepunch
3,66m wide broadloom carpet, with non-woven primary backing and POWERbac woven synthetic secondary backing,
treated with Stain Shield Fibre® soil resistant treatment. Laid on 1200g/m² underfelt in accordance with SANS 1419:1997,
all installed by approved installer in accordance with SANS 10186:2000. All install strictly to manufacturer’s specifications
on well-prepared screed. Colour and type to Architect’s approval.
Skirting : Pedross Clipstar or similar approved 14,5 x 95mm high wood veneered skirting board - colour to Architect's
approval, clipped onto steel clips, plugged and screwed to wall at 300mm centres.
NOTE :
a) Where applicable, all expansion joints in screed to be according to carpet expansion joint detail.
b) Where floor covering change from one floor finish to another, the finishes should be divided with a 25mm x 3mm brass
dividing strip cast into screed at position as indicated on detail drawing (flush with floor finish).
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
FITTINGS & FIXTURES (C)
C01. Pinning board :
1000mm x 550mm High pin board as by VITREX SYSTEM 2300 or similar. All installed strictly to manufacturer’s
specifications – Colour to Architects approval.
C02. Pinning board :
1200mm x1000mm High pin board as by VITREX SYSTEM 2300 or similar. All installed strictly to manufacturer’s
specifications – Colour to Architects approval.
C03. Pinning board :
1500mm x 1000mm High pin board as by VITREX SYSTEM 2300 or similar. All installed strictly to manufacturer’s
specifications – Colour to Architects approval.
C04. White board :
Standard 1200mm x 1000mm white board as by VITREX SYSTEM 2200 (011-8262549). All installed strictly to
manufacturer’s specifications.
C05. White board :
Standard 1500mm x 1000mm white board as by VITREX SYSTEM 2200 (011-8262549). All installed strictly to
manufacturer’s specifications.
C06. Projector screen- Wall mounted pull-down :
Standard 1760mm x 1330mm projector screen (SC0273) complete with Keystone adjusters (SC0400) as by PARROT
products (051-5249908). All installed to wall strictly to manufacturers detail specifications
C07. 1000 X 500 X 1800 5 Tier stainless steel wire shelf :
Standard 1000 X 500 X 1800mm high PPA 200 MICRON coated 5 tier wire shelf unit complete with chrome stations with
adjustable feet (WSNC-1.5/5/5T) as by Locker Logistic (082 558 5153) Installed strictly to manufacturers specifications –
Colour to Architects approval.
C08. 1500 X 500 X 1800 5 Tier stainless steel wire shelf :
Standard 1500 X 500 X 1800mm high PPA 200 MICRON coated 5 tier wire shelf unit complete with chrome stations with
adjustable feet (WSNC-1.5/5/5T) as by Locker Logistic (082 558 5153) Installed strictly to manufacturers specifications –
Colour to Architects approval.
C09. 1000 X 500 X 1800 5 Tier stainless steel solid shelf :
Standard 1000 X 500 X 1800mm high PPA 200 MICRON coated 5 tier solid shelf unit complete with chrome stations with
adjustable feet (SSNC-1/5/5T) as by Locker Logistic (082 558 5153). Installed strictly to manufacturers specifications –
Colour to Architects approval.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
C10. 1500 X 500 X 1800 5 Tier stainless steel solid shelf :
Standard 1500 X 500 X 1800mm high PPA 200 MICRON coated 5 tier solid shelf unit complete with chrome stations with
adjustable feet (SSNC-1/5/5T) as by Locker Logistic (082 558 5153). Installed strictly to manufacturers specifications –
Colour to Architects approval.
C11. 1000 X 350 X 1800 5 Tier stainless steel solid shelf :
Standard 1000 X 350 X 1800mm high PPA 200 MICRON coated 5 tier solid shelf unit complete with chrome stations with
adjustable feet(SSNC-1/3/5T) as by Locker Logistic (082 558 5153). Installed strictly to manufacturers specifications –
Colour to Architects approval.
C12. Shelvit shelving systems :
Standard 16mm thick Shelvit melamine covered Pine shelves SB300 Series (white) as shown on plan, screw fixed from
below to shelve rest clips (without grommets) on 3-lug brackets on single/double slotted wall stripping 1200mm high
(colour as by Architect) fixed to wall strictly according to manufacturer's specification
C13. 6 Tier wire baskets :
Standard X6 575 X 350 X 130mm wire baskets complete with wall supports for 6 baskets with PPA 200 MICRON finish (6
TIER G-T.S.U) as by Locker Logistic (082 558 5153). Installed strictly to manufacturers specifications – Colour to Architects
approval.
C14. Lockers :
Standard x3 PPA 200 MICRON coated two tier change lockers (LOC/2T), as by Locker Logistic (082 558 5153). Installed
strictly to manufacturers specifications – Colour to Architects approval.
C15. Double X-ray viewing screen :
Standard 960 x 429 2 plate surface mount single X-ray viewing screen complete with switch and fluorescent lamps (HUXRU-W-02) as by HUTZ (041 4844937). Installed strictly to manufacturers specifications – Colour to Architects approval.
C16. Filing cabinet :
Standard 4drawer Power Coated mild steel Filing cabinet complete with locking mechanism (FC – 4) as by Locker Logistic
(082 558 5153). – Colour to Architects approval.
C17. Drip rails :
Hospi-Slick Drip Rails: CODE: H/S/DR1-3 (011 - 8242473) - Natural Anodised (10 micron) extruded profile H/S/2897
formed in straight lengths 1m long including stop ends. Fixing: Direct to ceiling including timber supports 50 x 50 x 38 –
SA Pine.
(NOTE: Installed centre on bed position, 700mm from bed head centre and parallel to bed head wall, ceiling to be
supplied with additional suspenders to support additional weight) Hospi-Telescopic Intravenous Drip Hangers: CODE:
H/T/D (011 - 8242473)
Polished 304 stainless Steel system – comprising of a Teflon handle and release button (Tra005 - Code D/H/T2: (2 hook))
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
C18. Bed curtain tracks(Ceiling mounted) :
Hospi-Shadowline Cubical Bedscreen rails: CODE: SK/S21 (011- 8242473)
Natural Anodised (10 micron) extruded profile H/S/43353 formed to accommodate bed closures as shown on plan –
complete with 12 runners per 1/m and end stops. Fixing: Direct to ceiling including timber supports 50 x 50 x 38 – SAPine.
For lengths refer to plan.
Hospi-Track Bedscreen Curtains: CODE: H/T/BS1900 (011- 8242473) Manufactured in a Poly-cotton/nylon, non-iron, nonstain, fully washable material @ a ration of 1:25 to length of Bedscreen Rail. (NOTE: additional suspenders to be installed
for additional rail and curtain weight)
C19. Two Seater airport bench :
Rodlin Design SS Airport 2 seater free standing chairs, size 420 x 520mm wide, finished with epoxy powder coated frame
and brushed stainless steel perforated shells, aluminium epoxy powder coated legs, including all necessary fixing bolts,
etc.
C20. Three seater airport bench :
Rodlin Design SS Airport 3 seater free standing chairs, size 420 x 520mm wide, finished with epoxy powder coated frame
and brushed stainless steel perforated shells, aluminium epoxy powder coated legs, including all necessary fixing bolts,
etc.
C21. Four seater airport bench :
Rodlin Design SS Airport 4 seater free standing chairs, size 420 x 520mm wide, finished with epoxy powder coated frame
and brushed stainless steel perforated shells, aluminium epoxy powder coated legs, including all necessary fixing bolts,
etc.
C22. Loose standing Meeting room chairs :
Plastic bistro style design cafe chairs as by DP Plastic Solutions (011 791 1070) - Cafe chair 3, or similar approved , colour to
Architects approval, injection moulded from durable virgin PP plastic with UV stabilizer and colour fast pigments with
anodized aluminium legs with non slip feet. The durable materials allow for indoor and outdoor use.
C23. Rifle safe :
Chubb rifle safe, external size 1400 x 320 x 300mm deep, mass 60kg, with 6mm steel plate door and 3mm thick body with
one way 25mm moving with fixed back rebate/bolts boltwork including 1 x 7 lever keylock. Fix to wall to manufacturer's
specification.
C24. Bumper rail :
FloorworX Intrad PVC Beige high impact resistant wall protection system, comprising 1000mm long x 200mm high x 29mm
deep lipped channel profile (code: TR200) clipped onto 25mm wide uPVC brackets (code : TRP200), plugged and screwed
to solid brick wall at maximum 400mm centres, including stopends. Bumper rail to be centre on bed position.
C25. Corner protector :
Purpose-made 75 x 75 x 1.6mm thick stainless steel corner protector. Install from skirting level to 1200mm above FFL
(length to suit skirting height), bedded into paintable soft fill, plugged and screwed with countersunk stainless steel
screws, all to Architect's approval.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
C26. Bulk compact filing system :
Bulk Filing System as by Scarab Projects (011 262 5095/5250) or similar approved – 10 Bays of High Density Mobile
Shelving 2484mm high x (3x 940mm) wide x 416mm Deep , having 7 shelves to the height, creating 10 openings. The
depth of the shelves are 381mm Deep which is sufficient for lever arch filing or A4 Boxes. Colour to Architect's approval.
installed strictly according to manufacturer's specification.
C27. Stainless steel wall bench :
Franke 1,2mm Grade 304 18/10 stainless steel W wall bench (Code: 359564), size 1850 x 650 x 1050mm with 50mm high
integral splashback to rear and ends, 50 x 10mm turndown, stainless steel slatted undershelf (Code: 359268), size 1850 x
420mm wide, underside sprayed with vermin proof bitumastic sound deadening, fixed to wall with anchor bolts 900mm
from finished floor level and supported on 2No. detachable Grade 304 (18/10) stainless steel round legs (Code: 352658),
size 41mm diameter x 1,2mm thick, fitted with chrome plated adjustable flanged foot pieces.
C28. Stainless steel wall benches :
Franke 1,2mm Grade 304 18/10 stainless steel W wall benches (Code: 359564), size 1850x 650x1050mm and
1500x650x1050mm joined together by maufacturer to form 90deg as on plan, with 50mm high integral splashback to rear
and ends, 50 x 10mm turndown, stainless steel slatted undershelf (Code: 359268), size 1850 x 420mm wide, underside
sprayed with vermin proof bitumastic sound deadening, fixed to wall with anchor bolts 900mm from finished floor level
and supported on 2No. detachable Grade 304 (18/10) stainless steel round legs (Code: 352658) each, size 41mm diameter
x 1,2mm thick, fitted with chrome plated adjustable flanged foot pieces.
C29. Outdoor gym equipment :
Standard outdoor gym equipment as by World Outdoor Fitness SA (011 - 477 2023) installed strictly according to
manufacturer's specification.
C30. Medicine cabinet :
Lockable Medicare Drug Cabinet Small - Cat. No.EC0E45 including 1x shelf. Mild steel wall mountable cabinet with white
epoxy coated finish. Size: H 440 x L 360 x D 230mm installed strictly according to manufacturer's specification
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
Joinery (D)
1.
All dimensions of joinery work to be checked on site and shop drawings to be presented to
Architect for approval prior to any manufacturing of joinery work.
2.
Unless otherwise specified, hardware and ironmongery to be as specified or similar
approved
3.
Door hinges : To be Boss type hinges for side panel mounting, including trim cups. Install
minimum 2 hinges per Leaf up to 1000mm high and maximum 600mm spacing for hinges on
doors higher than 1000mm.
4.
Drawer runners : To be full metal sided and rear– fully retractable with 16mm SUPALAM
(Colour White) drawer bases. Sides of drawers to be 500mm deep x 150mm high
5.
Locks : (All doors and drawers to be lockable – keyed alike per room with Master Key)
Door locks : To be Cyberlock-Short Bolt Travel Left or Right (Finish Nickle)
SDT/Grass Ref : Rim Lock Nickle 22mm (Mastered) 7CL601-22-N
Mounting screws : 746190 - 6X19 Screw
Drawer locks : To be locked in series of four in height, with Face Fitting Cyberlock Central
Locking System for recessing in the Cabinet Side Panel, SDT/Grass Ref: 700mm Central
Locking System/Nickle (4 Drawer), 7CL603-700-N, 197480 - Zargen Locking Bracket
Mounting screws : 749160 - 6X16 Screw
6.
Cupboard door catches : BUCHEL TYPE : Elbow catch (Rooster) - Reference : B1566
7.
Door stops : HAFELE TYPE : Press fit WHITE
8.
Handles : HAFELE TYPE : Reference : 129.57.701 (Colour Architect's approval)
9.
Floor cupboards described excluding worktops (Worktops described elsewhere)
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
D01. 450 Floor cupboard with door :
Size 450mm x 560mm x 880mm high, comprising base structure from:
Surface : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,
Finish to front face with FORMICA HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO
4586:1995 HG/S Horizontal General Purpose / Standard 0.8mm thick.
Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard SANS EN 312-5:1997 bottom fixed base, fixed
mid-shelf and 75mm wide cross bearers to top and rear of cupboard.
Backer : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,Finish to outer face
with 0.8mm Formica HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S
Horizontal General Purpose / Standard 0.8mm thick.Edge all round with minimum 2mm thick PVC edging, colour as per
Colour Schedule. 3mm Melamatched WHITE rear in-fill panel, groove mounted to panels, 100mm high recessed skirting.
Hinged door over full width and height from:
Surface : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 HG/P Horizontal General Purpose / Postformable
grade
Substrate : 16mm BISONBORD Particleboard SANS EN 312-3:1996 finish on outer face with
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 White cabinet liner to inside.
Door / drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
D02. 450 Floor cupboard with 4x drawers :
Size 450mm x 560mm x 880mm high, four pull-out drawers equal in height, comprising base structure from:
Surface : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,
Finish to front face with FORMICA HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO
4586:1995 HG/S Horizontal General Purpose / Standard 0.8mm thick.
Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard SANS EN 312-5:1997 bottom fixed base, fixed
mid-shelf and 75mm wide cross bearers to top and rear of cupboard.
Backer : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,Finish to outer face
with 0.8mm Formica HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S
Horizontal General Purpose / Standard 0.8mm thick.Edge all round with minimum 2mm thick PVC edging, colour as per
Colour Schedule. 3mm Melamatched WHITE rear in-fill panel, groove mounted to panels, 100mm high recessed skirting.
Drawers from:
Surface : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 HG/P Horizontal General Purpose / Postformable
grade
Substrate : 16mm BISONBORD Particleboard SANS EN 312-3:1996 finish on outer face with
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 White cabinet liner to inside.
Drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
D03. 900 Floor cupboard with double doors :
Size 900mm x 560mm x 880mm high with double doors of equal size, comprising base structure from:
Surface : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,Finish to front face
with FORMICA HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S Horizontal
General Purpose / Standard 0.8mm thick.Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard SANS
EN 312-5:1997 bottom fixed base, fixed mid-shelf and 75mm wide cross bearers to top and rear of cupboard.
Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard SANS EN 312-5:1997 bottom fixed base, fixed
mid-shelf and 75mm wide cross bearers to top and rear of cupboard.
Backer : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,Finish to outer face
with 0.8mm Formica HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S
Horizontal General Purpose / Standard 0.8mm thick.Edge all round with minimum 2mm thick PVC edging, colour as per
Colour Schedule. 3mm Melamatched WHITE rear in-fill panel, groove mounted to panels, 100mm high recessed skirting.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
D03. .....continued
Hinged doors over full width and height from:
Surface : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 HG/P Horizontal General Purpose / Postformable
grade
Substrate : 16mm BISONBORD Particleboard SANS EN 312-3:1996 finish on outer face with
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 White cabinet liner to inside.
Door / drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
D04. 1000 Floor cupboard with double doors :
Size 1000mm x 560mm x 880mm high with double doors of equal size, comprising base structure from:
Surface : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,Finish to front face
with FORMICA HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S Horizontal
General Purpose / Standard 0.8mm thick.Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard SANS
EN 312-5:1997 bottom fixed base, fixed mid-shelf and 75mm wide cross bearers to top and rear of cupboard.
Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard SANS EN 312-5:1997 bottom fixed base, fixed
mid-shelf and 75mm wide cross bearers to top and rear of cupboard.
Backer : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,Finish to outer face
with 0.8mm Formica HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S
Horizontal General Purpose / Standard 0.8mm thick.Edge all round with minimum 2mm thick PVC edging, colour as per
Colour Schedule. 3mm Melamatched WHITE rear in-fill panel, groove mounted to panels, 100mm high recessed skirting.
Hinged doors over full width and height from:
Surface : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 HG/P Horizontal General Purpose / Postformable
grade
Substrate : 16mm BISONBORD Particleboard SANS EN 312-3:1996 finish on outer face with
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 White cabinet liner to inside.
Door / drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
D05. 450 Broom cupboard :
Cupboard size 450mm x 560mm x 2040mm high, comprising base structure, bottom base, sides, fixed upper shelf, top,
rear and single hinged door. Construct completely from:
Surface : 1.2mm Formica High Pressure Laminate (HPL with Loglare finish) SANS ISO 4586:1995 HG/S Horizontal General
Purpose.
Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard in accordance with SANS
EN 312-5:1997.
Backer : 1.2mm Formica High Pressure Laminate (HPL with Loglare finish) SANS ISO 4586:1995 HG/S Horizontal General
Purpose. All cupboard components edged in 3mm PVC edging all round, colour as per Architect. Fabrication cut outs, i.e.
hinge pockets, etc. to receive a water repellent solution prior to mounting of components. Skirting 100mm to be finished
in 0.8mm thick FORMICA HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S
Horizontal General Purpose / Standard type. All exposed edges are to be properly sealed with a minimum of 2 coats of
exterior grade Polyurethane varnish to prevent moisture ingress. Fix to wall. Door / drawer edges finished all round in a
minimum 3mm thick PVC edging, colour to Architect's approval.
D06. 900 Wall cupboard :
Size 900mm x 300mm x 720mm high, comprising bottom panel, side panel, fixed mid-shelf and top panel from:
Surface : Bisonlam Melamine Faced Board (MFB) SANS 1763:1998 edged all round in 1mm PVC edging, colour as per
Colour Schedule.
Substrate: 16mm Bisonbord Particlebord SANS EN 312-3:1996
Backer : Bisonlam Melamine Faced Board (MFB) SANS 1763:1998
3mm Melamatched WHITE rear in-fill panel, groove mounted to panels
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
D06. .....continued
Hinged doors over full width and height from:
Surface : 0.8mm Formica High Pressure Laminate (HPL with Loglare finish) SANS ISO 4586:1995 HG/S Horizontal General
Purpose / Standard.
Substrate : 16mm Bisonbord Particleboard in accordance with SANS EN 312-3:1996.
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS ISO 4586:1995 CL Grade white liner
Door / drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
D07. 1000 Wall cupboard :
Size 1000mm x 300mm x 720mm high, comprising bottom panel, side panel, fixed mid-shelf and top panel from:
Surface : Bisonlam Melamine Faced Board (MFB) SANS 1763:1998 edged all round in 1mm PVC edging, colour as per
Colour Schedule.
Substrate: 16mm Bisonbord Particlebord SANS EN 312-3:1996
Backer : Bisonlam Melamine Faced Board (MFB) SANS 1763:1998
3mm Melamatched WHITE rear in-fill panel, groove mounted to panels
Hinged doors over full width and height from:
Surface : 0.8mm Formica High Pressure Laminate (HPL with Loglare finish) SANS ISO 4586:1995 HG/S Horizontal General
Purpose / Standard.
Substrate : 16mm Bisonbord Particleboard in accordance with SANS EN 312-3:1996.
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS ISO 4586:1995 CL Grade white liner
Door / drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
D08. Consulting Room joinery :
Filing shelf :Purpose-made 450wide x 300deep x 550mm high timber filing shelf with 10x shelves of equal height as by
specialist. Colour to Architects approval.
Floor cupboard : Size 450mm x 560mm x 720mm high,three pull-out drawers equal in height, comprising base structure
from:
Surface : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,
Finish to front face with FORMICA HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO
4586:1995 HG/S Horizontal General Purpose / Standard 0.8mm thick.
Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard SANS EN 312-5:1997 bottom fixed base, fixed
mid-shelf and 75mm wide cross bearers to top and rear of cupboard.
Backer : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels,Finish to outer face
with 0.8mm Formica HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S
Horizontal General Purpose / Standard 0.8mm thick.Edge all round with minimum 2mm thick PVC edging, colour as per
Colour Schedule. 3mm Melamatched WHITE rear in-fill panel, groove mounted to panels, 100mm high recessed skirting.
Drawers from:
Surface : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 HG/P Horizontal General Purpose / Postformable
grade
Substrate : 16mm BISONBORD Particleboard SANS EN 312-3:1996 finish on outer face with
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS 4586:1995 White cabinet liner to inside.
Drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
Wall cupboard : Size 900mm x 300mm x 720mm high, comprising bottom panel, side panel, fixed mid-shelf and top panel
from:
Surface : Bisonlam Melamine Faced Board (MFB) SANS 1763:1998 edged all round in 1mm PVC edging, colour as per
Colour Schedule.
Substrate: 16mm Bisonbord Particlebord SANS EN 312-3:1996
Backer : Bisonlam Melamine Faced Board (MFB) SANS 1763:1998
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
D08. .....continued
3mm Melamatched WHITE rear in-fill panel, groove mounted to panels
Hinged doors over full width and height from:
Surface : 0.8mm Formica High Pressure Laminate (HPL with Loglare finish) SANS ISO 4586:1995 HG/S Horizontal General
Purpose / Standard.
Substrate : 16mm Bisonbord Particleboard in accordance with SANS EN 312-3:1996.
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS ISO 4586:1995 CL Grade white liner
Door / drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
Worktop : 1545x1350, in section 640mm wide and with 450mm chamfer as shown, over cabinet and standard adjustable
chromed legs. Constructed from:
Surface : Formica LifeSeal worktop with 0.8mm Formica HPL – HG/P surface with Loglare finish
Substrate: 32mm Bisonbord HMR
Backer : 0.8mm FORMICA HPL–BK brown backer
Worktop to accommodate 180 degrees post-formed bull nose edges to all exposed sides. (all joints and edges against
walls and sink cut-outs to be waterproofed). Colour to Architects approval.
D09. 900x900 Corner floor cupboard :
Corner unit, size 900mm x 900mm outer x 880mm high, with double door on right angles to required width, comprising
base structure from:
Surface : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels, Finish to front face
with FORMICA HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S Horizontal
General Purpose / Standard 0.8mm thick.
Substrate: 16mm Bisonbord V313 (High Moisture Resistant) Particleboard SANS EN 312-5:1997 bottom fixed base, fixed
mid-shelf and 75mm wide cross bearers to top and rear of cupboard.
Backer : Bisonlam Melamine Faced Board (MFB) in accordance with SANS 1763:1998 to side panels, Finish to outer face
with 0.8mm Formica HPL (High Pressure Laminate with Loglare finish) in accordance with SANS ISO 4586:1995 HG/S
Horizontal General Purpose / Standard 0.8mm thick. Edge all round with minimum 2mm thick PVC edging, colour as per
Colour Schedule. 3mm Melamatched WHITE rear in-fill panel, groove mounted to panels, 100mm high recessed skirting.
Hinged doors over full width and height from:
Surface : 0.8mm Formica High Pressure Laminate (HPL with Loglare finish) SANS ISO 4586:1995 HG/S Horizontal General
Purpose / Standard.
Substrate : 16mm Bisonbord Particleboard in accordance with SANS EN 312-3:1996.
Backer : 0.8mm Formica High Pressure Laminate (HPL) SANS ISO 4586:1995 CL Grade white liner
Door / drawer edges finished all round in a minimum 3mm thick PVC edging, colour to Architect's approval.
D10. Worktop (with sink cut-out) :
Surface : Formica LifeSeal worktop with 0.8mm Formica HPL – HG/P surface with Loglare finish with 100mm high fitted
rear and side splash back (Top053). Side splash back to be fitted where required when a top is fitted at a corner.
Substrate: 32mm Bisonbord HMR
Backer : 0.8mm FORMICA HPL–BK brown backer
worktops are to be purpose-made to required length x 600mm wide with Squareline front profile.
Splashback backer : 0,8mm Formica HPL-BK backer, SANS ISO 4586:1995, having a 90 degrees profiled top profile, and is
to be supplied and installed separately.
All exposed ends of worktops edged in 3mm PVC edging (colour as per Colour Schedule) to full profile and edges butting
up against walls. Cut-outs to worktops to accommodate for stainless steel sinks to size. Cut-out edges to receive minimum
two coats water repellent sealant. Placement of sinks to be applied by means of imbedding sink flange areas in an
approved sealant.
Sink installation by means of mechanical fixing as per sink supplier specifications. Where applicable, top to be supported
against wall by means of 38 x 38 x 2mm thick mild steel angle iron cleat finished with high quality mild steel paint system,
colour to match wall finish.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
D11. Wall fitted vanity tops :
Wall fitted vanity tops to specified lengths, size through section 550mm deep with 40mm high resin fitted side and rear
splash (Top054) and 200mm high downstand. Side splash back to be fitted where required when a top is fitted at a corner.
Construct from :
Surface : 12mm SURINNO Solid Surfacing Material.
Substrate: 16mm Supawood Medium Density Fibreboard (MDF) SANS 540-1:1991, Incorporate minimum 6mm radius
corners in lengths. Vanity unit with open ends to incorporate down stand/return to width of top. Cut-outs in vanity units
to receive under mounted hand washbowl, basins (bowl code FS102, size through bowl 498 x 346 x 169mm deep), special
bowls as indicated. Finish all on cut-out edge 8mm radius. Vanity units to exhibit seamless joints throughout. Vanity units
to be laid on minimum 16mm SUPAWOOD MDF (Medium Density Fibreboard) in accordance with SANS 5401:1991.Support brackets to vanity underside depth to be from 32mm x 32mm x 3.2mm thick mild steel tubing. Powder
coat finish (type S1). Support brackets fitted not to exceed 500mm centers.
D12. Cupboard / brackets mounted worktop :
Worktop mounted on cabinet and / or brackets (D15), to specified length (also see plan), in section 600mm wide.
Constructed from:
Surface : Formica LifeSeal worktop with 0.8mm Formica HPL – HG/P surface with Loglare finish
Substrate: 32mm Bisonbord HMR
Backer : 0.8mm FORMICA HPL–BK brown backer. Worktop to accommodate 180 degrees post-formed bull nose edges to
long ends on either sides.
D13. Worktop :
1545x1350, in section 640mm wide and with 450mm chamfer as shown, over cabinet and standard adjustable chromed
legs. Constructed from:
Surface : Formica LifeSeal worktop with 0.8mm Formica HPL – HG/P surface with Loglare finish
Substrate: 32mm Bisonbord HMR
Backer : 0.8mm FORMICA HPL–BK brown backer
Worktop to accommodate 180 degrees post-formed bull nose edges to all exposed sides. (all joints and edges against
walls and sink cut-outs to be waterproofed). Colour to Architects approval.
D14. Worktop/ chairs :
Proposed position only. To be specified by others
D15. Worktop support brackets :
Purpose-made 32x32x3.2mm SHS worktop support brackets to match worktop width minus 50mm, all as by specialist and
to centres as shown on room elevation. Brackets to be welded to joints, pre-drilled and countersunk holed for wall and
worktop fixings. Powder coat black. All open ends in brackets to be plugged with black nylon plugs.
D16. Counters :
Nurses station / reception counters as per later detail.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
D17. Wall fitted lab top :
Wall fitted lab top to specified length, size through section 800mm deep with 40mm high resin fitted side and rear splash
strips. Construct from :
Surface : 12mm SURINNO Solid Surfacing Material.
Substrate: 16mm Supawood Medium Density Fibreboard (MDF) SANS 540-1:1991, Incorporate minimum 6mm radius
corner in front. Cut-out in top to receive under mounted lab sink (E08). Finish all cut-out edges with 8mm radius. Fix on
standard Labfurn support brackets according to manufacturer's specification
D18. Book shelf :
1200x400x16mm thick Shelvit melamine covered Pine shelves SB300 Series (white) as shown on plan, screw fixed from
below to purposed made support brackets as per detail.
D19. Filing shelf :
Purpose-made 450wide x 300deep x 550mm high timber filing shelf with 10x Supawood shelves with equal spacings as by
specialist. Colour to Architects approval.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
Sanitary (E)
E01. Medical WHB with elbow taps :
Vaal Sanitaryware Hygia ceramic vitreous china hospital basin colour White (code: 703611), size 585 x 435mm with two
tapholes, plugged and screwed to walls with two screws including chromium plated caps (code: 8513Z0) and sealed with
silicone sealant where basin meets wall.
Plumbing: Cobra or similar 15mm Chrome plated elbow action wall-type mixer with swanneck swivel spout outlet and
hook and angle regulating valves (515/053232H21).Cobra Watertech 32mm Machine chrome plated slotted basin waste
union (303).COBRA 345/50 chrome plated bottle trap, 50mm pvc outlet.
E02. Medical WHB with bibtaps :
Vaal Sanitaryware Hygia ceramic vitreous china hospital basin colour White (code: 703611), size 585 x 435mm with two
tapholes, plugged and screwed to walls with two screws including chromium plated caps (code: 8513Z0) and sealed with
silicone sealant where basin meets wall.
Plumbing: Cobra Watertech Star 15mm chrome plated extended bibtap (Code: 206EXT-15) with hot and cold indices, flow
straightner and sliding wall flange. Cobra Watertech 32mm Machine chrome plated slotted basin waste union
(303).COBRA 345/50 chrome plated bottle trap, 50mm pvc outlet.
E03. Ablution WHB :
Vaal Sanitaryware Daisy vitreous china wall mounted basin colour White (Code: 7008), size 510 x 400mm with two
tapholes, including integrated overflow and chainstay hole bolted to wall with two 10mm bolts (Code: 8448Z0) and sealed
with silicone sealant where basin meets wall.
Plaumbing: Cobra Watertech Star 15mm pillar tap with flanged backnut and raised nose hose (code: 112), manufactured
in accordance with SANS 226:2004 Type 1 (BS 5412).
E04. Soap dispenser :
Franke Rodan RODX619E 0,8mm thick satin finished stainless steel recessed soap dispenser (Code: 359982), size 241 x 86 x
243mm high with 1 litre capacity, front push button, cylinder lock and Franke standard key, plugged and screwed to the
wall with stainless steel screws. Installed strictly to manufacturers specifications. One per basin. Also see room
elevations for exact position.
E05. Paper towel dispenser :
Franke Stratos STRX600 1,2/1,5mm thick satin finished stainless steel paper towel dispenser (Code: 359700), size 300 x
134 x 305mm high with a capacity of 300-400 towels and cylinder lock with standard Franke key, plugged and screwed to
the wall with stainless steel screws. Also see room elevations for exact position.
E06. Paper towel disposer
Franke Rodan RODX605 0,8mm thick satin finished stainless steel waste bin (Code: 359983), size 355 x 168 x 460mm high
with capacity of 23 litres and cylinder lock and standard Franke key, plugged and screwed to the wall with stainless steel
screws. Also see room elevations for exact position.
E07. Mirror :
450mm x 600mm High quality mirror complete with beveled edges installed on wall tiles. Plug and screw to wall with X4
chromed mirror screws with dome caps. Also see room elevations for exact position.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
E08. Lab basin :
435 x 335mm Lab Sink ceramic fireclay laboratory sink colour White, with waste outlet including acid resistant waste
fitting fitted underneath opening in worktop surface, on and including two adjustable underslung brackets, complete with
lab mixer - All as by lab furniture specialist.
E09. Baby bath :
Purpose made solid surface baby bath integrated into solid surface top complete with under mounted bath (bath product
code SS180, size through bowl 680 x 380 x 170mm deep) – all according to joinery schedule.
Plumbing: (Cobra 011 951-5000)
Cobra sa 862 fail safe thermostatic mixer with
Cobra c-017 handshower with diverter for aerated flow or handspray used in conjunction with
Cobra c-017-1 ½ “elbow assembly and
Cobra 009-1 c.p deck mounting unit complete with Cobra heavy duty hose and adaptor 008CO to handshower.
Cobra Watertech 32mm Chrome plated unslotted basin waste union (no chain or stay) (308).
COBRA 309-32 “anti-theft” plug
COBRA 345/50 chrome plated bottle trap, 50mm, pvc outlet
COBRA angle regulating valves – COBRA 232/350.
COBRA Flexible hose 950mm long – 008CO
E10.Disabled suite :
WC
Vaal Sanitaryware Pearl Paraplegic vitreous china floor mounted paraplegic washdown suite colour White (Code: 7300SC)
comprising semi close couple 90º outlet open rim washdown pan and matching 9 litre cistern, including lid, fitments and
purpose-made chromium plated side flush lever.
WHB
Vaal Sanitaryware (016 - 360 6000) 510 x 405mm Hibiscus White vitreous china lavatory basin (product code 7050) with
two tapholes including integrated overflow and chainstay hole, bolted to wall with two 10mm bolts (product code
8448ZO).
Plumbing (Cobra 011 951-5000)
Two COBRA 503-21 ½’ elbow action pillar taps, CP, Cold water tap to be closest to WC
Cobra Watertech 32mm Machine chrome plated slotted basin waste union (303).
COBRA 309-32 “anti-theft” plug
COBRA 345/50 bottle trap, 50mm, pvc outlet.
COBRA angle regulating valves – COBRA 232/350.
MIRROR
450mm x 900mm high quality mirror complete with beveled edges installed on wall tiles. Plug and screw to wall with X6
chromed mirror screws with dome caps. One per basin. Also see room elevations for exact position.
STRAIGHT GRAB RAIL
Standard 800mm long x to clear WC cistern projecting straight disabled rail (KB18) as by Stainless Steel Design or similar.
Installed strictly to manufacturers specifications.
DOGLEG SIDE GRAB RAIL
Standard 300 x 300 x 300 x 80mm projecting dog leg side rail (KB26) as by Stainless Steel Design (left or right hand as per
plan). Installed strictly to manufacturers specifications.
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
E11. Slophopper :
Franke Kitchen Systems (0861 372 653) (t/a Citimetal) grade 304 (18/10) stainless steel model CH slop hopper size 540 x
700mm(Special 00907) with 100mm integral splashback to back and both sides, bowl with integral flushing rim, 110mm
diameter waste outlet, hinged bucket grid and 38mm diameter x 250mm long vertical inlet pipe, complete with Franke
Stainless steel Two piece S-trap, on pair of 40 x 40mm stainless steel tube brackets, each twice bolted to wall with M8
expansion bolts.(Franke - 052-4445241/3)
Plumbing: (Cobra 011 951-5000)
20mm Cobra junior flush master wc with (FJ2.210)
Franke CP Brass adaptor ( Code 403195).
E12. Bedpan sink :
Franke Kitchen Systems (t/a Citimetal) grade 304 (18/10) stainless steel model EL bedpan wash-up sink and drainer size
1130 x 685mm with 150mm high splashback, seamless sluice bowl with integral flushing rim and 110mm diameter outlet
pipe, 35mm Cobra FM1.000 flushvalve, with bedpan and bottle spray nozzles, each with 15mm elbow action valve, and
fixing on pair of stainless steel gallow brackets and legs with adjustable feet, each bracket twice bolted to wall with M8
expansion bolts and each foot twice plugged and screwed to floor.
E13. Hydroboil :
Franke Kitchen Systems (t/a Citimetal) ZIP Hydroboil 7,5 litre Stainless steel water boiler as manufactured by Franke
Kitchen Systems, plugged and screwed to wall. (15mm cold water supply with service valve , waist for safety valve
connected to waste water system, and electrical connections elsewhere)all to comply with NBR (Code 380004). Installed
above sink to manufacturers specifications.
E14. External bibtaps :
Cobra Watertech Star 15mm chrome plated hose bibtap (Code: 207EC-20) with wing nut and lining, manufactured in
accordance with SANS 226:2009 Type 1 (BS 5412).
E15. WC :
Vaal Sanitaryware Daisy vitreous china semi close coupled washdown pan comprising 90º outlet open rim pan (product
code 751400) flushing valve including lid and fitments with heavy duty seat.
Plumbing: Walker Crosweller - WALCRO 107C HP - 20mm BSP, with union, SABS, DZR brass, ‘built in’, front access, box
type toilet flushing valve complete with galvanised box, stainless steel concealing cover plate, flush pipes, elbow and pan
connector.
Maintained operating pressure: 100 kPa – 600 kPa
E16. SEB Sink :
Franke Trendline Model 1000x460 SEB Grade 304 18/10 polished stainless steel single end bowl drop on sink (Code:
311050), overall size 1000 x 460mm with one 350 x 460 x 140mm deep bowl, fitted onto cupboard (elsewhere specified)
including PVC trap (trap elsewhere specified) with 38mm waste fitting.
Plumbing: (Cobra 011 951-5000)
Cobra Watertech Star 15mm wall mounted sink mixer with overarm swivel outlet and adjustable wall flanges code
(166/041 and S-041).
Cobra Watertech 40mm Chrome plated unslotted basin waste union (no chain or stay) (317-40).
COBRA 309-40 “anti-theft” plug
COBRA 365/50 bottle trap, 50mm, pvc outlet
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
E17. DEB Sink :
Franke Trendline Model 1200x535 DEB Grade 304 18/10 polished stainless steel double end bowl drop on sink (Code:
312081), overall size 1200 x 535mm with two 343 x 410 x 140mm deep bowls, fitted onto cupboard (elsewhere specified)
including PVC traps (traps elsewhere specified) with 38mm waste fitting.
Plumbing: (Cobra 011 951-5000)
Cobra Watertech Star 15mm wall mounted sink mixer with overarm swivel outlet and adjustable wall flanges code
(166/041 and S-041).
Cobra Watertech 40mm Chrome plated unslotted basin waste union (no chain or stay) (317-40).
COBRA 309-40 “anti-theft” plug
COBRA 365/50 bottle trap, 50mm, pvc outlet
E18. Urinal :
Vaal Sanitaryware 600 x 385 x 380mm Lavatera white vitreous china wall mounted top inlet urinal (code: 705426)
including 38mm chromium plated domical grating (code: 8787Z0) and chromium plated top inlet spreader
(code: 7054Z1), flush valve Cobra FJ6000, fixed on and including two hanger brackets (code: 8127Z0) and urinal division
(code: 7052) fixed with and including fixing screws and hanger bracket.
E19. Toilet roll dispenser :
Franke Rodan RODX672E 0,8mm thick satin finished stainless steel recessed double toilet roll holder with spindle system
(Code: 359988), size 184 x 341 x 138mm deep for 2 rolls maximum 120mm diameter with cylinder lock with standard
Franke key, plugged and screwed to the wall with stainless steel screws.
E20. Mop / broom hooks :
1200x600mm Sloped screed towards floor outlet as by Engineer (see plan).
Purpose made back plate to be 900 x 450mm high non magnetic 1.6mm stainless steel plate with grid180 satin finish ,
glued and screwed (with wall plugs) to a wall surface, with an approved adhesive and x6 countersunk stainless steel
screws. Complete with standard stainless steel wall rail - 900mm long with x5 broom hooks as by Hychem – Accessories
(www.hychem.co.za). Rail to be installed 1500mm above finished floor level. Sample installation to be pre approved by
Architect.
E21. Pot sink :
Franke 1,2mm Grade 304 18/10 stainless steel P1 pot sinks (Code: 350001), size 900 x 650 x 1050mm with 760 x 460 x
380mm deep bowl, 150mm high integral splashback to rear, 50 x 10mm turndown and 40mm waste outlet, underside
sprayed with vermin proof bitumastic sound deadening, fixed to wall with anchor bolts 900mm from finished floor level
and supported on Grade 304 (18/10) stainless steel square gallows brackets with detachable front leg (Code: 352654), size
40 x 40 x 1,2mm thick, fitted with chrome plated adjustable flanged foot pieces.
Plumbing: (Cobra 011 951-5000)
Cobra Watertech Star 15mm wall mounted sink mixer with overarm swivel outlet and adjustable wall flanges code
(166/041 and S-041).
Cobra Watertech 40mm Chrome plated unslotted basin waste union (no chain or stay) (317-40).
COBRA 309-40 “anti-theft” plugs
COBRA 365/50 bottle trap, 50mm, pvc outlet
Note : TRADE NAMES: All materials, fittings and finishes specified may be replaced by equal and approved alternatives.
E22. Shower plumbing :
Cobra Watertech Star 15mm wall mounted undertile shower stop taps code (X2 138-15).
Cobra Watertech shower arm (026)
Cobra Watertech Typhoon shower head (KP2.51) Cobra Watertech 40mm Rough brass screwed male shower waste with
75mm diameter Chrome plated shower grating (323).
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement