Tri Band GSM/GPRS modem and GPS receiver

Tri Band GSM/GPRS modem and GPS receiver
WIRELESS COMMUNICATIONS GMBH
STEPP II
Tri Band GSM/GPRS modem and GPS receiver
Tri Band GSM/GPRS Engine
Voice, SMS, Data, TCP/IP
12 channel GPS receiver
Integrated TCXO
Online Tracking
Automotive temperature range
Active cooling and heating
element
Configurable history function
Real time object tracking
Configurable geo-fencing
Data logging
Starter-kit including evaluation
and configuration tool
The FALCOM STEPP II
is a Plug & Play GSM/GPRS/GPS terminal with an
embedded configurable software application.
The device concept is targeting for direct implementation as a mobile client in a wide range of
high volume, low-cost, flexible system solutions like
AVL, fleet management, vehicle security and recovery and other related area.
The tracking functionality of the embedded mobile client application is combined with variety of
alert messaging capabilities. The configurable alert messages contain current position and status
report and use 4 digital and 2 analogue inputs
as hardware back-bone. In addition to that two
predefined digital inputs are detecting ignition line
and main power (car battery) failure.
Depending on the specific system solution scenario four digital outputs allow the remote control
of external actuators. The integrated two audio
channels allow voice communication too.
The STEPP II concept reduces the efforts for the creation of a turn key tracking and security solution
to the definition of the server (dispatcher) application. In this way the time-to-market, the design-in
risk and the total cost of solution are substantially
reduced.
The STEPP II-STARTERKIT provides an easy and efficient way to evaluate and configure all system
parameters of the mobile client. The configuration
of the STEPP can be done via local serial link or remotely via the GSM network.
www.falcom.de
Hardware details
Technical specification
Software features
- Configurable geo-fencing
- Configurable history with
more than 100.000 records
- Configurable localisation and
status report upon dispatcher
request
- Configurable localisation and
status report by timer
- Configurable four digital and
two analogue inputs for alert
messaging
- Four digital outputs for remote
control of external actuators
- Configurable sleep mode
Evaluation kit
GSM / GPRS core
STEPP II / 55: Siemens MC55
STEPP II / 56: Siemens MC56
GSM / GPRS frequency
STEPP II / 55: 900/1800/1900 MHz
STEPP II / 56: 850/1800/1900 MHz
GPS acquisition rate
Snap start: < 3 sec., average
Hot start: < 8 sec., average
Warm start: < 38 sec., average
Cold start: < 45 sec., average
GSM services
Phone, Data, SMS
Power supply
DC 10,8 - 31,2 V
External LiIon backup battery supported
Internal LiIon battery charger
GPRS services
GPRS class B, class 10
TCP/IP
Physical characteristics
Dimensions (LxWxH): 55 x 88 x 22 mm
Weight: approx.120 g
GPS core
Temperatur range
OEM single board 12 channel GPS revceiver Operation: -40° to +85° C
C/A code: 1.023 MHz chip
(active cooling and heating element)
SiRFstarII low power chipset
TXCO (temperature compensated
Interfaces
ttcrystal oscillator)
16pin MOLEX 43045-1609:
Casing: fully shielded
4 digital inputs, 2 analogue inputs
Memory: 16 Mbit Flash memory
4 digital outputs, ignition, power input,
External microphone, battery input
GPS datum
15pin AMP 5-558556-1:
WGS-84
RS232 (Rx, Tx), 2 speaker, 1 microphone
Power Output, Vbatt, boot signal
DGPS accuracy
SIM card reader for small 3 V SIM cards
Position 1 to 5 m typical
GPS RF connector 50 Ohm FAKRA/Radiall
Velocity 0.05 m/sec typical
GSM RF connector 50 Ohm FAKRA/Radiall
2 LED’s for GSM and GPS core status
WIRELESS COMMUNICATIONS GMBH
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement