Remote control. This is how easily the right - Busch
Remote control.
This is how easily the right atmosphere
with light is created.
Comfortably controlling the light from any point in the room.
The radio control system with its manual remote control function also offers the option of integrating additional control elements without any further wiring, simply via radio signal. With
the Busch-Remote Control IR, you can operate individual light
sources or store entire lighting scenes which can then be recalled at the press of a button.
528 Remote control | Catalogue 2014/2015
01
Remote control
01 Remote control WaveLINE RF.
02 Busch-Watchdog 220 WaveLINE,
Infrared movement detector
03 IR Flush-mounted switch,
Busch-Remote control IR
04 WaveLINE LED display
Switch series: solo®. Colour: studio white
05 Wall-mounted transmitter WaveLINE,
2-channel RF, switch series f uture ® linear,
studio white
06 The WaveLINE switch actuator, 1gang, with
extension unit, serves for switching electric
loads via radio control
Contents
Remote control
WaveLINE transmitter
02
03
p. 538
WaveLINE actuators, RF/KNX media converters
p. 540
WaveLINE window sensor, universal detector
p. 543
Busch-Remote control IR flush-mounted inserts
p. 545
Busch-Remote control IR control elements
p. 547
Busch-Remote control IR built-in/socket outlet receiver
p. 549
04
05
06 | NEW
Catalogue 2014/2015 | Remote control 529
RF sensors
01
02
03
04
01 SM WaveLINE movement detector,
05
02 WaveLINE media converter TP-RF,
Article-No. 6747 AGM-204-500
Article-No. 6770-500
The WaveLINE Busch-Watchdog 220 is a batteryoperated movement detector. Since it is installed
without cables it can be mounted in the most ideal
position. The battery has a service life of 5 years.
03 Window sensor,
The KNX and Busch radio control are coupled via the
WaveLINE media converter TP-RF. Telegrams can be
exchanged in both directions. One application serves
to transmit the window sensor to the KNX system.
04 Universal detector,
Article-No. 6720-64
05 Remote control RF,
Article-No. 6721-64
The WaveLINE window sensor is retrofitted between
the window and window handle, which means the
original window handle is retained. The window
handle is used for the following window positions:
opened, tilted and closed.
Article-No. 6780-500
The WaveLINE universal detector is suited for skylights or sliding doors and is activated via a reed contact. The universal detector has a second channel
which can be permanently wired to a floating contact
(NO or NC contacts).
The remote control is used as mobile control for
the WaveLINE. Loads can be controlled individually
and scenes can be started.
Control elements
Switch ranges
pure stainless steel
1gang
2gang
4gang
solo®
6731-xx-500 6732-xx-5006733-xx-500
Busch-axcent®
6731-xx-500 6732-xx-5006733-xx-500
future® linear
6731-xx-500 6732-xx-5006733-xx-500
Reflex SI
1gang
2gang
6731-866-500 6732-866-5006733-866-500
6731-214-5006732-214-500
Busch-Duro 2000® SI6731-212-500
6732-212-500
530 Remote control | Catalogue 2014/2015
RF actuators /displays
01
02
03
05 | NEW
06 | NEW
07
04 | NEW
01 1gang WaveLINE actuator,
Article-No. 6702-500
02 2gang WaveLINE actuator,
Article-No. 6703-500
03 WaveLINE dimming actuator,
Article-No. 6704-500
04 WaveLINE blind actuator,
Article-No. 6705-101-500
Before
05 1gang WaveLINE actuator,
Article-No. 6701-101-500
06 WaveLINE binary input, 2gang
Article-No. 6725-500
07 WaveLINE LED display, 4gang with
switching function, Article-No. 6730-84
After
Catalogue 2014/2015 | Remote control 531
Retrofitting a cross
connection I
03
01
02
04
01 WaveLINE wall-mounted transmitter, 1 channel, Article-No. 6731-84-500
02 WaveLINE wall-mounted transmitter, 1 channel, Article-No. 6731-84-500
03 WaveLINE switch actuator, Article-No. 6702-500
04 WaveLINE wall-mounted transmitter, 1 channel, Article-No. 6731-84-500
Retrofitting a cross connection: the
clever way, so that the ceiling light in
the bedroom can be operated from
both sides of the bed. For this the
existing switch, mostly located at the
door, is replaced by a wall-mounted
transmitter. Two wall-mounted transmitters, that are linked via radio signal
instead of cables, are also glued to the
wall next to the bed. The light can now
be remotely controlled via the separately mounted actuator.
Before
After
02
01
03
04
532 Remote control | Catalogue 2014/2015
Retrofitting a cross
connection II
04
02
01
02
03
03
Rocker assignment of 4gang
wall-mounted transmitter:
»» ceiling lamp
»» Table lamp left
»» Table lamp right
»» Bedroom complete
01 WaveLINE wall-mounted transmitter, 4 channel,
Article-No. 6733-84-500
02 2 x WaveLINE wall-mounted transmitters, 4 channel, Article-No. 6733-84-500
03 2 x WaveLINE switch actuators, Article-No. 6702-500
2 x SCHUKO® socket outlet inserts, Article-No. 20 EUC-84
04 WaveLINE universal dimming actuator, Article-No.
6704-500
For even greater comfort in the bedroom, additional functions can be
retrofitted together with a cross connection: switching and dimming the main
light additionally from both sides of the
bed and swit ching of two bedside table
lamps from all positions. Added to this is
the integration of a central function with
which all lamps can be switched off with
the press of a button when leaving the
room. Essential for these functions are
the WaveLINE 4-channel wall-mounted
transmitters that are installed in place of
the light switch and simply glued at the
side of the beds.
Before
After
02
Ceiling lamp
01
Table lamp
left
Table lamp
right
Bedroom
complete
Ceiling lamp
Table lamp
left
Table lamp
right
Bedroom
complete
02
Ceiling lamp
Table lamp
left
Table lamp
right
Bedroom
complete
03
04
2x
Catalogue 2014/2015 | Remote control 533
WaveLINE
Where conventional systems only check
whether the window is in contact with
the frame, WaveLINE goes a decisive
step further. It reports the position of
the window handle and thus provides
information as to whether the window
is locked.
Before:
Light switch
After:
LED display
and light switch
01
It’s so simple. Where a light switch or
dimmer was installed before, you can
now also use the message system
function. The original switching or
dimming function remains intact.
02
03
WaveLINE window position sensor
Window position sensors monitor and
transmit the position of the window
handle – it is indicated by means of a
coloured LED on the easy-to-view display, which can be individually labelled.
The pertinent window sensors mounted between the handle and the frame
are available in black, white, and stainless steel optics and thus well-suited
for all common window frames and
window handles. The existing window
handle can continue to be used.
04
01 WaveLINE LED display
6730-xx onto 6404 U
02 WaveLINE window position sensor, 6720-64
03 WaveLINE window position sensor, 6720-66
04 WaveLINE window position sensor, 6720-65
05 WaveLINE universal sensor, 6721-64
06 WaveLINE universal sensor, 6721-65
05
Bolt switch
contact
Basement
534 Remote control | Catalogue 2014/2015
06
WaveLINE universal sensor
The WaveLINE universal detector
is available as a supplement to the
WaveLINE window sensor. It is used
wherever window sensors cannot be
attached for mechanical reasons. The
universal detector has two independent message channels. The first channel is triggered by the reed contact,
while the second channel is firmly
wired to a floating contact.
Via the LED display, the two channels of the
universal detector can be transferred and
displayed separately.
You are thus always informed as to whether
the cellar door is closed and locked.
All windows under
surveillanceby radio control
Who doesn’t know that anxious feeling of
having forgotten something after leaving
home? An open window or a patio door left
ajar are an invitation to burglars. WaveLINE
replaces your last-minute check and guarantees security.
Bedroom
Workroom
The WaveLINE window position sensor,
which recognises the position of the window handle and transmits it by radio signal, is fitted between the window handle
and the window frame. The existing handle can continue to be used and additional
mounting is not required. All components
required for installation and operation are
included in the scope of delivery. A battery
is also provided – so the system is ready
for operation immediately. The information
is provided on an easy-to-view information and control element. It has a display
with four LEDs. Up to eight window
position sensors can be connected to a
single LED. In that way, either individual
windows or complete rooms or floors can
be monitored with only one indicator LED.
If several windows sensors are learned for
one LED, the group is networked automatically. A practical group could be, for
example, the windows of one floor.
If the LED display is fitted to an FM
insert from the KNX world, the device
functions as a gateway. It passes the
information which has been recorded
at the window sensor and transmitted
via radio control to the control element
on to the KNX. Also the function of the
on-site rocker switch is transmitted via
KNX and executed (a rocker switch
function for flush-mounted actuators).
This makes the display/control element
usable as 1gang control element with
the usual functions.
Bathroom
Store room
2nd floor
Children’s room 1
Children’s room 2
Bathroom
2nd floor
1st floor
Living room
Kitchen
Application example
Rauchalarmvernetzung per Funk
The LEDs indicate the following:
›› All the windows in one group are closed: LED green
›› At least one window is tilted:
LED yellow
›› At least one window of the group is open: LED red
Attention is also drawn to a battery losing its power or faulty window position
sensors by a flashing light.
Conventional Flush-mounted inserts
WaveLINE LED display
6730-84
Busch-Universal relay
switch insert, 6404 U
Universal Dimmer
switch insert, 6595 U
Catalogue 2014/2015 | Remote control 535
Busch-Remote control IR
01
02
03
05
04
06
As easily and conveniently as you can change the channels
of your TV with a remote control, you can also control the
various lights, blinds, and awnings in your living areas. At
the press of a button, you can switch and dim the lighting
01 Remote control
The Busch-Remote control IR remote control is the
heart of the system. It lets you trigger all functions
of the system as required. In practice, this means
the individual switching and dimming of the installed
Busch-Remote control IR receiver. Using the memo
function (Memo 1/Memo 2), you can save special
light situations and call them at the press of a button
at any time.
02 Wall-mounted transmitter
The ideal supplement to the remote control is the
Busch-Remote control IR wall-mounted transmitter as a central control element. Independent of
the mains and attachable to any point in the room,
including the window pane, it controls the memo
function or individual consumers and makes sure the
consumers are switched off safely (EVERYTHING
OFF) when everyone leaves the room. Available in the
colours of the alpha switch range.
536 Remote control | Catalogue 2014/2015
and no longer have to operating switch after individual
switch. In the process, the possibility to control your blinds
in this manner is unique.
03 Flush-mounted dimmer
With the Busch-Remote control IR universal dimmer,
outputs up to 420 W can be dimmed without a problem. In the process, the dimmer allows the connection of 230 V incandescent and halogen lamps, as
well as low-voltage halogen lamps with conventional
or electronic transformers due to its intelligent control
system. The memory function saves the value of the
last saved brightness.
04 Flush-mounted switch
Wherever high outputs have to be controlled, the
Busch-Remote control IR flush-mounted switch does
the job. With a switching capacity of 2,300 W/VA,
even large plants have sufficient reserves. Using the
memory function, any two switching states can be
saved and called as required.
05 Switch plug unit
With the Busch Remote Control IR switch plug unit
you can connect mobile consumers without extensive installation. Suitable for incandescent lamps, 230
V halogen lamps and low-voltage halogen lamps that
are operated via transformers. With memo function
for switching at callup. At the switching contact any
consumers with a connected load of up to 2,300 W
can be operated.
06 Fan control
The lighting is connected to the first output and the
fan at the second. After the lighting is switched off,
the fan keeps running up to the programmed time.
Insert 6402 U, control element 6067-xx.
Overview
Depth of product
range IR remote
control
Switching
2gang switch
top channel 1
bottom channel 2
Dimming
Dimming
0–10 V
Dimming
LED
Blind
Busch-Dimmer®
insert LED
6523 U-500
6524 U-500
Busch-Blind control
insert
6411U-101
6411U/S-500-101
Flush-mounted
Busch-Universal
relay insert
6401 U-102-500
Busch-Universal
2gang insert
6402 U-500
Busch-Universal
master dimmer
insert
6593 U-500
Busch-Memory
touch-type
controller
6550 U-101-500
Busch-Remote
control IR control
element
6067-xx-102
Busch-Remote
control IR control
element
6066-xx
Busch-Remote
control IR control
element
6066-xx-102
Busch-Remote
control IR control
element
6066-xx-102
IR receiver
4-channel
6056 EB-500
IR built-in receiver
6045 E-101-500
–
–
IR dimmer
0–10 V
6045-500
Busch-Blind
control II
built-in unit
6420 EB-500 +
IR Built-in
receiver
6045 E-101-500
IR switch
6080-24-500
–
–
–
–
IR control
element
6066-xx-102
Installation
Adapter plug
Please note also the option for the fan control on page 536
Additional information
is available in our range
and products brochure.
Brochure:
WaveLINE RF
0001-0-1334
Catalogue 2014/2015 | Remote control 537
WaveLINE transmitter
Product
Article-No.
Order-No.
Pack/Qty PG
Product
Wall-mounted transmitter WaveLINE 1)
1-channel
1gang wall-mounted transmitter independent of mains
power supply.
For switching and dimming.
For controlling blinds and light scenes.
1 radio channel can be operated or up to 2 light scenes can
be called up.
For flush-mounted WaveLINE actuators 6701-101, 6702,
6703, 6704 and 6705-101.
For LED display WaveLINE 6730-xxx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Send frequency: 868 MHz.
Free-field range: approx. 100 m.
Power supply: lithium button cell battery Type CR2032.
Battery service life: typically 5 years, therefore practically
maintenance-free.
Automatic monitoring of battery life.
Including fixing plate for mounting on smooth walls or on
switch boxes.
Control element: Switch contacts top/bottom
Display elements: LED to indicate the transmission
Rated voltage: 3 VProtection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 54 mm x 54 mm x 18 mm
Article-No.
Order-No.
Pack/Qty PG
Wall-mounted transmitter WaveLINE 1)
1-channel
1gang wall-mounted transmitter independent of mains
power supply.
For switching and dimming.
For controlling blinds and light scenes.
1 radio channel can be operated or up to 2 light scenes can
be called up.
For flush-mounted WaveLINE actuators 6701-101, 6702,
6703, 6704 and 6705-101.
For LED display WaveLINE 6730-xxx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Send frequency: 868 MHz.
Free-field range: approx. 100 m.
Power supply: lithium button cell battery Type CR2032.
Battery service life: typically 5 years, therefore practically
maintenance-free.
Automatic monitoring of battery life.
Including fixing plate for mounting on smooth walls or on
switch boxes.
Control element: Switch contacts top/bottom
Display elements: LED to indicate the transmission
Rated voltage: 3 VProtection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 54 mm x 54 mm x 18 mm
Busch-Duro 2000® SI
future® linear
212 white
6731-212-500
6730-0-0028
1/10
19
214 alpine white
Reflex SI
6731-214-500
6730-0-0030
1/10
19
1) Battery included in delivery.
82 ivory white
6731-82-500
83 aluminium silver 2) 6731-83-500
84 studio white
6731-84-500
866 stainless steel
Wall-mounted transmitter WaveLINE 1)
2-channel
2gang wall-mounted transmitter independent of mains
power supply.
For switching and dimming.
For controlling blinds and light scenes.
2 radio channels can be operated or up to 4 light scenes
can be called up.
For flush-mounted WaveLINE actuators 6701-101, 6702,
6703, 6704 and 6705-101.
For LED display WaveLINE 6730-xxx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Send frequency: 868 MHz.
Free-field range: approx. 100 m.
Power supply: lithium button cell battery Type CR2032.
Battery service life: typically 5 years, therefore practically
maintenance-free.
Automatic monitoring of battery life.
Including fixing plate for mounting on smooth walls or on
switch boxes.
Control element: Switch contacts top/bottom
Display elements: LED to indicate the transmission
Rated voltage: 3 VProtection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 54 mm x 54 mm x 18 mm
6732-212-500
6730-0-0029
1/10
19
214 alpine white
Reflex SI
6732-214-500
6730-0-0031
1/10
19
1) Battery included in delivery.
19
19
19
pure stainless steel 2)
6731-866-500
6730-0-0041
1/10
14
Wall-mounted transmitter WaveLINE 1) 2) 3)
2-channel
2gang wall-mounted transmitter independent of mains
power supply.
With labelling field and labelling strip.
For switching and dimming.
For controlling blinds and light scenes.
2 radio channels can be operated or up to 4 light scenes
can be called up.
For flush-mounted WaveLINE actuators 6701-101, 6702,
6703, 6704 and 6705-101.
For LED display WaveLINE 6730-xxx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Send frequency: 868 MHz.
Free-field range: approx. 100 m.
Power supply: lithium button cell battery Type CR2032.
Battery service life: typically 5 years, therefore practically
maintenance-free.
Automatic monitoring of battery life.
Including fixing plate for mounting on smooth walls or on
switch boxes.
Control element: rocker switch left/right
Display elements: LED to indicate the transmission
Rated voltage: 3 VProtection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 63 mm x 63 mm x 16 mm
future® linear
82 ivory white
6732-82-500
83 aluminium silver 4) 6732-83-500
84 studio white
6732-84-500
866 stainless steel
1)
2)
3)
4)
538 Remote control | Catalogue 2014/2015
1/10
1/10
1/10
1) Battery included in delivery.
2) Surface painted.
Busch-Duro 2000® SI
212 white
6730-0-0032
6730-0-0035
6730-0-0038
6730-0-0033
6730-0-0036
6730-0-0039
1/10
1/10
1/10
19
16
19
pure stainless steel 4)
6732-866-500
6730-0-0042
1/10
14
Battery included in delivery.
See labelling sheet 1799/0x.
Matching labelling sheet 1799 14.
Surface painted.
WaveLINE transmitter
Product
Article-No.
Order-No.
Pack/Qty PG
Product
Wall-mounted transmitter WaveLINE 1) 2) 3)
4-channel
4gang wall-mounted transmitter independent of mains
power supply.
With labelling field and labelling strip.
For switching and dimming.
For controlling blinds and light scenes.
4 radio channels can be operated or up to 8 light scenes
can be called up.
For flush-mounted WaveLINE actuators 6701-101, 6702,
6703, 6704 and 6705-101.
For LED display WaveLINE 6730-xxx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Send frequency: 868 MHz.
Free-field range: approx. 100 m.
Power supply: lithium button cell battery Type CR2032.
Battery service life: typically 5 years, therefore practically
maintenance-free.
Automatic monitoring of battery life.
Including fixing plate for mounting on smooth walls or on
switch boxes.
Control element: rocker switch left/right
Display elements: LED to indicate the transmission
Rated voltage: 3 VProtection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 63 mm x 63 mm x 16 mm
866 stainless steel
1)
2)
3)
4)
6730-0-0034
6730-0-0037
6730-0-0040
1/10
1/10
1/10
19
19
19
pure stainless steel 4)
6733-866-500
6730-0-0043
1/10
14
Battery included in delivery.
See labelling sheet 1799/0x.
Matching labelling sheet 1799 14.
Surface painted.
Remote control WaveLINE 1)
Network-independent radio control.
For switching and dimming.
For controlling blinds and light scenes.
With 3 groups (A, B or C) with 5 pairs of channels.
There are 15 radio channels operated singly or up to 30 light
scenes can be called.
With “ALL OFF” function for associated actuators.
For flush-mounted WaveLINE actuators 6701-101, 6702,
6703, 6704 and 6705-101.
For LED display WaveLINE 6730-xxx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Send frequency: 868 MHz.
Free-field range: approx. 100 m.
Power supply: lithium button cell battery Type CR2032.
Battery service life: typically 5 years, therefore practically
maintenance-free.
Automatic monitoring of battery life.
Control element: 3 group buttons, 10 channel buttons and
“ALL OFF” button.
Display elements: 3 LEDs for group selection display.
Rated voltage: 3 VProtection class (Device): IP 40
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 135 mm x 50 mm x 16 mm
black
6780-500
6780-0-0001
1/10
Order-No.
Pack/Qty PG
WaveLINE binary input, 2gang, 230 V~ 1)
Radio control telegrams are sent when the two extension
units are activated with mains voltage (AC 230 V~).
Operation also possible via conventional push-buttons
(2020 US, 2012/6 UK).
The 2gang binary input has 5 function modes:
1.) 2-channel switching: Connection of conventional push
buttons. Alternately sends ON/OFF telegrams when actuated.
2.) 2-channel dimming: Connection of conventional push
buttons. Sends dimming telegrams when actuated.
3) 1-channel blind: Connection of a 2gang push-button or
a blind control II insert. Sends telegrams to control a blind
when actuated.
4.) Two-channel light scene control: Connection of conventional push-buttons. Light scenes are stored and started
when actuated.
5.) Channel 1: Switching ON. Channel 2: Continuous
switching ON/OFF: At “Switching ON” an ON telegram is
sent with a brief actuation. At “Continuous switching” ON/
OFF and actuated extension unit, an ON telegram is sent
every minute, and an OFF telegram is sent every minute for
a non-actuated extension unit.
In dependence of the selected function, it can be combined
with WaveLINE actuators 6701-101, 6702, 6703, 6704,
6705-101.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Repeater function can be activated for extended range.
For universal attachment or installation.
Phase and neutral conductor required.
For installation in (deep) flush-mounted boxes to German
Standard DIN 49073, Part 1.
Send/receive frequency: 868 MHz.
Free-field range: approx. 100 m.
Control element: Adjustable potentiometer
Display elements: LED for status display.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Inputs: 2
Polling voltage: 230 V~, potential-connected
Protection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 47 mm x 48 mm x 14 mm
Mounting depth: 15 mm
future® linear
82 ivory white
6733-82-500
83 aluminium silver 4) 6733-83-500
84 studio white
6733-84-500
Article-No.
white
6725-500
6720-0-0008
1/10
19
1) For further information please check the current e-catalogue.
19
1) Battery included in delivery.
Technical information
www.BUSCH-JAEGER-catalogue.com
Catalogue 2014/2015 | Remote control 539
WaveLINE transmitter
Product
Article-No.
Order-No.
WaveLINE actuators, RF/
KNX media converters
Pack/Qty PG
Busch-Watchdog 220 WaveLINE 1) 2)
Wireless movement detector for detecting thermal motion.
With display for detection and status indication.
With ground and rear-field detection.
With high-quality lens for optimum detection.
Surveillance density: 84 sectors with 336 switching segments.
With integrated dismantling protection.
All functions controlled by microprocessor.
With automatic range stabilization.
With automatic interference suppression.
With automatic dazzle-proofing.
With automatic battery monitoring.
Battery service life: typically 5 years, therefore practically
maintenance-free.
With brightness-independent test mode for evaluating the
detection zone.
Individual adjustment of detection range via enclosed protective foil which can be cut to size.
Combinable with switch actuator WaveLINE, 1gang, with
extension unit 6701-101.
Compatible with WaveLINE KNX gateway TP-RF 6770.
For standalone and group operation.
Switch-off delay: 3 min. (single mode), individually adjustable
at actuator (group mode).
Send frequency: 868 MHz.
Free-field range: approx. 100 m.
Rated voltage: 4.5 VDetection range: frontal: 16 m, lateral: 16 m
Detection angle: 220 °
Brightness limit value: 0.5 Lux - 300 Lux , Daytime operation
Mounting height: 2.5 m
Protection class (Device): IP 55
Temperature range (Device): -25 °C to 55 °C
Dimensions: (L x W x D): 115 mm x 125 mm x 141 mm
201
204
208
35
brown
alpine white
silver metallic
anthracite
6747 AGM-201-500
6747 AGM-204-500
6747 AGM-208-500
6747 AGM-35-500
6700-0-0038
6700-0-0035
6700-0-0036
6700-0-0037
1) Battery included in delivery.
2) Battery type: Lithium batteries 1250 mAh (L92 AAA 1.5 V).
1
1
1
1
29
29
29
29
Product
Article-No.
Order-No.
WaveLINE switch actuator, 1gang, with extension unit 1)
For wireless switching of electrical loads.
Functions via radio control: ON/OFF, timer and light scene
control.
Functions via the extension unit: ON/OFF, timer and sending
a radio control telegram.
Operation also possible via conventional push-buttons
(2020 US, 2012/6 UK).
Actuation of the extension unit (via conventional pushbutton) causes the output to switch and a radio control
telegram to be sent.
Actuation of extension unit in ON/OFF function: Alternate
sending of an ON/OFF telegram.
Actuation of extension unit in timer function: Sending of an
ON telegram.
For Busch-Watchdog WaveLINE.
For wall mounted transmitter Waveline 6731-xxx, 6732-xxx
und 6733-xxx.
For remote control WaveLINE 6780.
For WaveLINE window position sensor 6720-6x.
For WaveLINE 6721-xx universal signalling unit.
For Busch-EnergyControl 6762-xx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Switch-off delay: Adjustable to 5 seconds, 1-5-15 minutes.
Repeater function can be activated for extended range.
For universal attachment or installation.
3 wire connection (neutral conductor required).
For installation in (deep) flush-mounted boxes to German
Standard DIN 49073, Part 1.
Controllable up to 32 transmission addresses.
Send/receive frequency: 868 MHz.
Free-field range: approx. 100 m.
Control element: Adjustable potentiometer
Display elements: Status indication of output via LED.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Inputs: 1
Polling voltage: 230 V~, Sensing pulse, L-wire
Outputs: 1x Normally open contact, potential-bound
Suitable for: Resistive load
Rated current: 10 A
Output voltage: 230 V~
Rated power: 2300 W
Suitable for: capacitive
Rated current: 10 AX
Output voltage: 230 V~
Rated power: 2300 VA
Suitable for: inductive
Rated current: 10 A, cos φ 0.6
Output voltage: 230 V~
Rated power: 2300 VA
Protection class (Device): IP 20
Temperature range (Device): -20 °C to 45 °C
Dimensions: (L x W x D): 47 mm x 48 mm x 22 mm
Mounting depth: 25 mm
6701-101-500
6700-0-0040
1) For further information please check the current e-catalogue.
540 Remote control | Catalogue 2014/2015
Pack/Qty PG
1/10
19
WaveLINE actuators, RF/
KNX media converters
Product
Article-No.
Order-No.
Pack/Qty PG
Switch actuator WaveLINE
For wireless switching of electrical loads.
For functions ON/OFF, timer and lightscene control.
For wall mounted transmitter Waveline 6731-xxx, 6732-xxx
und 6733-xxx.
For remote control WaveLINE 6780.
For WaveLINE window position sensor 6720-6x.
For WaveLINE 6721-xx universal signalling unit.
For Busch-EnergyControl 6762-xx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Abschaltverzögerung: 1 s - 5 min. einstellbar.
Repeater function can be activated for extended range.
For universal attachment or installation.
3 wire connection (neutral conductor required).
For installation in (deep) flush-mounted boxes to German
Standard DIN 49073, Part 1.
Controllable up to 32 transmission addresses.
Send/receive frequency: 868 MHz.
Free-field range: approx. 100 m.
Control element: Adjustable potentiometer
Display elements: Status indication of output via LED.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Outputs: 1x Öffner oder Schließer, potentialfrei
Suitable for: Resistive load
Rated current: 10 A
Output voltage: 230 V~
Rated power: 2300 W
Suitable for: capacitive
Rated current: 10 AX
Output voltage: 230 V~
Rated power: 2300 VA
Suitable for: inductive
Rated current: 10 A, cos φ 0.6
Output voltage: 230 V~
Rated power: 2300 VA
Protection class (Device): IP 20
Temperature range (Device): -20 °C to 45 °C
Dimensions: (L x W x D): 47 mm x 48 mm x 22 mm
Mounting depth: 25 mm
6702-500
6700-0-0023
1/10
19
Product
Article-No.
Order-No.
Pack/Qty PG
2gang switch actuator WaveLINE 1)
For wireless switching of electrical loads.
For operation mode 2gang switch, 2 separate outputs.
For operation mode timer: output 1 (eg lighting), output 2:
ON/Off delay in dependence of output 1 (eg fan control).
For functions: ON/OFF and light scene control.
For wall mounted transmitter Waveline 6731-xxx, 6732-xxx
und 6733-xxx.
For remote control WaveLINE 6780.
For WaveLINE window position sensor 6720-6x.
For WaveLINE 6721-xx universal signalling unit.
For Busch-EnergyControl 6762-xx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
ON/OFF delay output 2: 2 min. / 30 s.
Repeater function can be activated for extended range.
For universal attachment or installation.
3 wire connection (neutral conductor required).
For installation in (deep) flush-mounted boxes to German
Standard DIN 49073, Part 1.
Controllable up to 32 transmission addresses.
Send/receive frequency: 868 MHz.
Free-field range: approx. 100 m.
Control element: Adjustable potentiometer
Display elements: Status indication of output via LED.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Outputs: 2x Normally open contact, potential-bound
Suitable for: 230 V incandescent lamps
Rated current: 3 A
Output voltage: 230 V~
Rated power: 700 W
Suitable for: Fluorescent lamps
Rated current: 3 AX
Output voltage: 230 V~
Rated power: 700 VA
Suitable for: Low-voltage halogen lamps with conventional
transformers or electronic transformers.
Rated current: 3 A
Output voltage: 230 V~
Rated power: 700 W/VA
Protection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 47 mm x 48 mm x 22 mm
Mounting depth: 25 mm
6703-500
6700-0-0024
1/10
19
1) For further information please check the current e-catalogue.
Technical information
www.BUSCH-JAEGER-catalogue.com
Catalogue 2014/2015 | Remote control 541
WaveLINE actuators, RF/
KNX media converters
Product
Article-No.
Order-No.
Pack/Qty PG
Universal dimming actuator WaveLINE 1) 2) 3) 4)
For wireless switching and dimming of electrical loads.
For functions ON/OFF, dimming and lightscene control.
With soft ON/OFF function.
With selectable light value storage.
For wall mounted transmitter Waveline 6731-xxx, 6732-xxx
und 6733-xxx.
For remote control WaveLINE 6780.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Repeater function can be activated for extended range.
For universal attachment or installation.
2-wire connection (neutral conductor not required)
3-wire connection system (neutral conductor is required) is
preferred when using electronic transformers.
For installation in (deep) flush-mounted boxes to German
Standard DIN 49073, Part 1.
Controllable up to 32 transmission addresses.
Send/receive frequency: 868 MHz.
Free-field range: approx. 100 m.
Control element: Adjustable potentiometer
Display elements: Status indication of output via LED.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Outputs: 1x dimming channel
Suitable for: 230 V incandescent lamps
Output voltage: 230 V~
Rated power: 35 - 210 W
Suitable for: Low voltage halogen lamps, which are operated by electronic transformers.
Rated power: 35 - 210 VA
Suitable for: Low-voltage halogen lamps with conventional
transformers or electronic transformers.
Rated power: 35 - 175 VA
Protection class (Device): IP 20
Temperature range (Device): 0 °C to 35 °C
Dimensions: (L x W x D): 47 mm x 48 mm x 33 mm
Mounting depth: 35 mm
6704-500
1)
2)
3)
4)
6700-0-0025
1/10
Neutral conductor can be connected as option for load-dependent fluctuations in light values.
In case of electronic transformers, 5 % transformer losses.
In the case of conventional transformers, take ~20% transformer loss into account.
For further information please check the current e-catalogue.
19
Product
Article-No.
Order-No.
WaveLINE series/blind actuator with extension unit 1)
For wireless switching of electrical loads.
For driving and adjusting blinds/shutters and awnings over
radio.
Functions via radio control: 2gang switch, blind switch and
light scene control.
Functions via extension unit: 2gang switch, blind switch and
send radio control telegram.
Operation also possible via conventional push-buttons
(2020 US, 2012/6 UK).
Actuation of the extension unit (via conventional pushbutton) causes the output to switch and a radio control
telegram to be sent.
Actuation of the extension unit in 2gang switch function: An
ON/OFF telegram is sent alternately.
Actuation of the extension unit in blind switch function:
Extension unit 1 sends an UP and extension unit 2 sends a
DOWN telegram.
For wall mounted transmitter Waveline 6731-xxx, 6732-xxx
und 6733-xxx.
For remote control WaveLINE 6780.
For WaveLINE window position sensor 6720-6x.
For WaveLINE 6721-xx universal signalling unit.
For Busch-EnergyControl 6762-xx.
Compatible with WaveLINE KNX gateway TP-RF 6770.
With blind switch function: 3 minutes run time.
Repeater function can be activated for extended range.
For universal attachment or installation.
3 wire connection (neutral conductor required).
For installation in (deep) flush-mounted boxes to German
Standard DIN 49073, Part 1.
Controllable up to 32 transmission addresses.
Send/receive frequency: 868 MHz.
Free-field range: approx. 100 m.
Control element: Adjustable potentiometer
Display elements: Status indication of output via LED.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Inputs: 2
Polling voltage: 230 V~, Sensing pulse, L-wire
Outputs: 2x Normally open contact, potential-bound
Suitable for: Electrical drives.
Rated current: 3 A, cos φ 0.5
Output voltage: 230 V~
Rated power: 690 VA
Suitable for: 230 V incandescent lamps
Rated current: 3 A
Output voltage: 230 V~
Suitable for: Fluorescent lamps
Rated current: 3 AX
Output voltage: 230 V~
Protection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 47 mm x 48 mm x 22 mm
Mounting depth: 25 mm
6705-101-500
6700-0-0042
1) For further information please check the current e-catalogue.
542 Remote control | Catalogue 2014/2015
Pack/Qty PG
1/10
19
WaveLINE actuators, RF/
KNX media converters
Product
Article-No.
WaveLINE window sensor,
universal detector
Order-No.
Pack/Qty PG
Product
KNX Gateway TP-RF 1) 2) 3)
KNX Twisted Pair/ KNX WaveLine RF
media converter with internal antenna for conversion of the
radio signals to the KNX ABB i-bus® KNX with 24 channels.
For the evaluation and transfer of up to 24 channels each
with 4 sub-channels as transmitter or receiver.
Simple operation due to “programming button” and display
on the device.
Is surface-mounted.
Control element: 3 control buttons
Display elements: Segment display
Connections:
KNX-line: Bus connection terminal
Rated voltage: 24 VInputs: 24
Protection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 84 mm x 84 mm x 36 mm
6770-500
6770-0-0002
1
Order-No.
Article-No.
Pack/Qty PG
WaveLINE LED display 1) 2)
For status display of window handle positions: open = red,
closed = green, tilted = yellow.
Direct onsite operation possible for switching / dimming an
electrical device depending on the flush-mounted insert.
4 individual LED display channels.
Up to 8 WaveLine transmitters can be taught-in on each
LED display channel.
Up to 8 WaveLine transmitters can be taught-in on onsite
operation.
After a power cut all LED-Display channels light in red. The
cyclic telegram repeat of the WaveLINE window position
sensor 6720-xxx sensor automatically updates the window
open state.
Status display for depleted WaveLINE transmitter battery.
Status display for faulty transmission link and defective
WaveLINE transmitter.
User-friendly start-up without PC / software.
Printed labelling sheet with 8 different inlay sheets.
For WaveLINE window position sensor 6720-6x.
For WaveLINE 6721-xx universal signalling unit.
For Busch-Watchdog 220 WaveLINE 6747 AGM.
For Busch-Universal relay switch insert 6404 U.
For universal dimmer switch insert 6595 U.
./.
Free-field range: approx. 100 m.
Send/receive frequency: 868 MHz.
Protection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 54 mm x 54 mm
19
1) For software and description please check the current e-catalogue.
2) ETS programming only with ETS 3.0f or higher
3) RF-/WaveLINE components are available in chapter Remote control.
Busch-Duro 2000® SI
212 white
6730-212
6730-0-0001
1
14
214 alpine white
Reflex SI
6730-214
6730-0-0002
1
14
1) See labelling sheet 1799 xx.
2) See labelling sheet 1799/0x.
WaveLINE LED display 1) 2)
For status display of window handle positions: open = red,
closed = green, tilted = yellow.
Direct onsite operation possible for switching / dimming an
electrical device depending on the flush-mounted insert.
4 individual LED display channels.
Up to 8 WaveLine transmitters can be taught-in on each
LED display channel.
Up to 8 WaveLine transmitters can be taught-in on onsite
operation.
After a power cut all LED-Display channels light in red. The
cyclic telegram repeat of the WaveLINE window position
sensor 6720-xxx sensor automatically updates the window
open state.
Status display for depleted WaveLINE transmitter battery.
Status display for faulty transmission link and defective
WaveLINE transmitter.
User-friendly start-up without PC / software.
Printed labelling sheet with 8 different inlay sheets.
For WaveLINE window position sensor 6720-6x.
For WaveLINE 6721-xx universal signalling unit.
For Busch-Watchdog 220 WaveLINE 6747 AGM.
For Busch-Universal relay switch insert 6404 U.
For universal dimmer switch insert 6595 U.
For ABB i-bus® KNX devices 6110 U, 6114 U, 6120 U-102.
Free-field range: approx. 100 m.
Send/receive frequency: 868 MHz.
Protection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 55 mm x 70 mm
alpha
20 platinum 3)
21 bronze 3)
22G ivory
24 studio white matt
24G studio white
260 palladium 3)
266 titanium 3)
6730-20
6730-21
6730-22G
6730-24
6730-24G
6730-260
6730-266
6730-0-0007
6730-0-0008
6730-0-0009
6730-0-0010
6730-0-0011
6730-0-0005
6730-0-0006
1
1
1
1
1
1
1
14
14
14
14
14
14
14
1) See labelling sheet 1799 xx.
2) See labelling sheet 1799/0x.
3) Surface painted.
Technical information
www.BUSCH-JAEGER-catalogue.com
Catalogue 2014/2015 | Remote control 543
WaveLINE window sensor,
universal detector
Product
Article-No.
Order-No.
Pack/Qty PG
WaveLINE LED display 1)
For status display of window handle positions: open = red,
closed = green, tilted = yellow.
Direct onsite operation possible for switching / dimming an
electrical device depending on the flush-mounted insert.
4 individual LED display channels.
Up to 8 WaveLine transmitters can be taught-in on each
LED display channel.
Up to 8 WaveLine transmitters can be taught-in on onsite
operation.
After a power cut all LED-Display channels light in red. The
cyclic telegram repeat of the WaveLINE window position
sensor 6720-xxx sensor automatically updates the window
open state.
Status display for depleted WaveLINE transmitter battery.
Status display for faulty transmission link and defective
WaveLINE transmitter.
User-friendly start-up without PC / software.
Printed labelling sheet with 8 different inlay sheets.
For WaveLINE window position sensor 6720-6x.
For WaveLINE 6721-xx universal signalling unit.
For Busch-Watchdog 220 WaveLINE 6747 AGM.
For Busch-Universal relay switch insert 6404 U.
For universal dimmer switch insert 6595 U.
Free-field range: approx. 100 m.
Send/receive frequency: 868 MHz.
Protection class (Device): IP 20
Temperature range (Device): -5 °C to 45 °C
Dimensions: (L x W x D): 63 mm x 63 mm
Product
Article-No.
Order-No.
Pack/Qty PG
Busch-Universal relay switch insert 1)
For switching incandescent lamps, 230 V tungsten halogen
lamps, fluorescent lamps and low-voltage halogen lamps,
that are actuated via transformers.
3 wire connection (neutral conductor required).
With operating mode switch for operating mode: switch,
time switch.
Switch operating mode: press on the upper rocker switch
half to switch the light on, press on the lower rocker switch
half to switch the light off.
Time switch operating mode: press on the upper rocker
switch half to switch the light on, the light automatically
switches off after a time delay. Manual switching off not
possible. The delay can be set in 5 steps between 30 and
300 secs.
Operation also possible via conventional push buttons
(2020 US, 2021/6 UK).
For LED display WaveLINE 6730-xxx.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Inputs: 1
Polling voltage: 230 V~, Sensing pulse, L-wire
Outputs: 1x Normally open contact, potential-bound
Suitable for: ohmic, capacitive and inductive loads
Rated current: 10 AX
Rated power: 2300 W/VA
Protection class (Device): IP 20
Temperature range (Device): 0 °C to 35 °C
Dimensions: (L x W x D): 49 mm x 49 mm x 33 mm
future® linear 2)
81
82
83
84
884
anthracite
ivory white
aluminium silver 3)
studio white
studio white,
matt 3)
885 black matt 3)
6730-81
6730-82
6730-83
6730-84
6730-0-0014
6730-0-0015
6730-0-0016
6730-0-0017
1
1
1
1
14
14
14
14
6730-884
6730-885
6730-0-0026
6730-0-0027
1
1
14
14
solo® 2)
6730-82
6730-84
6730-803
6730-815
6730-0-0015
6730-0-0017
6730-0-0025
6730-0-0024
1
1
1
1
14
14
14
14
84 studio white
896 chalet-white
Busch-axcent®
6730-84
6730-896-500
6730-0-0017
6730-0-0066
1
1
14
14
81 anthracite
82 ivory white
84 studio white
carat® 2)
6730-81
6730-82
6730-84
6730-0-0014
6730-0-0015
6730-0-0017
1
1
1
14
14
14
866 stainless steel
pure stainless steel 4) 2)
6730-866
6730-0-0023
1
14
82
84
803
815
1)
2)
3)
4)
ivory white
studio white
grey metallic 3)
yellow
See labelling sheet 1799 xx.
See labelling sheet 1799/0x.
Surface painted.
Surface-painted
6404 U
6401-0-0055
14
1) Fixation by using key holes or attachable claws (enclosed).
Universal Dimmer Switch Insert 1) 2) 3)
For dimming and switching of incadescent lamps, 230 V
halogen lamps and low-voltage halogen lamps with conventional or electronic transformers.
2-wire connection (neutral conductor not required)
With soft ON/OFF function.
With electronic short-circuit protection.
With automatic overtemperature protection.
With operating mode switch for operating mode: dimmer,
switch
Dimmer operating mode: short press on the upper rocker
switch half to switch the light on, short press on the lower
rocker switch half to switch the light off.
Dimmer operating mode: long press on the upper rocker
switch half dims, with light switched on, the light brighter, or
with light switched off the light brighter from nothing. Long
press on the lower rocker switch half dims the light darker.
Switch operating mode: press on the upper rocker switch
half to switch the light on, press on the lower rocker switch
half to switch the light off.
Operation also possible via conventional push buttons
(2020 US, 2021/6 UK).
Do not operate conventional transformers and electronic
transformers together on the universal dimmer switch insert.
For LED display WaveLINE 6730-xxx.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Inputs: 1
Polling voltage: 230 V~, Sensing pulse, L-wire
Outputs: 1x electronic output, potential-bound
Suitable for: ohmic, capacitive and inductive loads
Rated power: 60 - 450 W/VA
Protection class (Device): IP 20
Temperature range (Device): 0 °C to 35 °C
Dimensions: (L x W x D): 49 mm x 49 mm x 33 mm
6595 U
6590-0-0188
1) Fixation by using key holes or attachable claws (enclosed).
2) In the case of conventional transformers, take ~20% transformer loss into account.
3) In case of electronic transformers, 5 % transformer losses.
544 Remote control | Catalogue 2014/2015
1
1
14
WaveLINE window sensor,
universal detector
Product
Article-No.
Order-No.
Busch-Remote control IR
flush-mounted inserts
Pack/Qty PG
WaveLINE window sensor
For monitoring and transmission of the current window
handle position (window open, closed, tilted).
The WaveLINE window sensor transmits the current window
handle position immediately upon operation.
Addition cyclic transmission for monitoring of the transmission link and the fault-free state of equipment.
Existing window handle is used.
The WaveLINE window sensor is installed between the
existing window handle and window frame.
Suitable for window handle: 7 mm square fastener, 43 mm
attachment screw separation, lifter dia. 10 and 12 mm, max.
mounting plate size 34 x 77 mm (WxH).
No wire laying required.
Accessories for assembly (square fastener extension,
screws, adapter for lifter) of the WaveLINE window position
sensor included in delivery.
Battery included in delivery.
Battery service life: typically 5 years, therefore practically
maintenance-free.
Monitoring of battery life and transmission of battery condition.
For LED display WaveLINE 6730-xxx.
For flush-mounted WaveLINE actuators 6701-101, 6702,
6703, 6704 and 6705-101.
Compatible with WaveLINE KNX gateway TP-RF 6770.
Free-field range: approx. 100 m.
Send frequency: 868 MHz.
Protection class (Device): IP 43
Temperature range (Device): -5 °C to 50 °C
Dimensions: (L x W x D): 168 mm x 38 mm x 13 mm
64 studio white matt 6720-64
65 basalt black
6720-65
66 stainless steel 1) 6720-66
6720-0-0001
6720-0-0002
6720-0-0003
1
1
1
14
14
14
1) Surface painted.
WaveLINE universal sensor
For monitoring and transmission of the state (open, closed)
of dormer windows, skylights, doors and gates.
For window surveillance with open fireplace and extractor
hood pursuant to Article 4 of the German Fire Prevention
Regulations.
Additional connection option for an external, potential-free
sensor (choice of normally closed or normally open contact).
Isolated evaluation and monitoring of channels.
The WaveLINE universal sensor immediately transmits the
current information when there is a change in state.
Addition cyclic transmission for monitoring of the transmission link and the fault-free state of equipment.
Attachment of WaveLINE universal sensor and magnets by
using adhesive foil or screws.
Accessories (adhesive foil, screws, magnet) included in
delivery.
Battery included in delivery.
Battery service life: typically 5 years, therefore practically
maintenance-free.
Monitoring of battery life and transmission of battery condition.
For LED display WaveLINE 6730-xxx.
For flush-mounted WaveLINE actuators 6701-101, 6702,
6703, 6704 and 6705-101.
Compatible with WaveLINE KNX gateway TP-RF 6770.
External sensor max. wire length: 5 m
External sensor terminal connection diameter :
0.14...0.5 mm² (single wire)
Free-field range: approx. 100 m.
Send frequency: 868 MHz.
Protection class (Device): IP 43
Temperature range (Device): -5 °C to 50 °C
Dimensions: (L x W x D): 118 mm x 30 mm x 22 mm
64 studio white matt 6721-64
65 basalt black
6721-65
Technical information
www.BUSCH-JAEGER-catalogue.com
6720-0-0004
6720-0-0005
1
1
Product
Order-No.
Article-No.
Pack/Qty PG
Busch-Universal relay switch insert
3 wire connection (neutral conductor required).
For Busch-Watchdog 180 flush-mounted Sensor Standard
6810-21x-101.
For Busch-Watchdog 180 flush-mounted sensor Comfort II
6800-xxx-104 and 6800-xxx-104M.
For Busch-Watchdog 180 FP sensor for All Weather 44
6800-3x-102C.
For Busch-Watchdog Presence tech 6813-xxx-101 und
6813/11-xxx.
For comfort timer control element 6455-101-500.
For Busch-Remote control IR control cover 6067-xxx-10x.
For control cover with control lamp 6543-xxx-10x.
Combinable with Busch-Watchdog extension insert 6805 U.
Operation also possible via conventional push buttons
(2020 US, 2021/6 UK).
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz/60 Hz
Outputs: 1x Normally open contact, potential-bound
Suitable for: 230 V incandescent lamps, 230 V halogen
lamps, fluorescent lamps and low-voltage halogen lamps,
that are operated via transformers.
Rated current: 10 AX
Rated power: 2300 W/VA
Temperature range (Device): -25 °C to 55 °C
British Standard EN 60669-2-1
6401 U-102-500
6401-0-0049
1/10
19
Busch-Universal 2gang 1way insert
3 wire connection (neutral conductor required).
For the serial switch operating mode: 2 separate outputs,
2 separate extension inputs.
For operation mode time switch: Output 1 (e.g. illumination),
Output 2: switch-on/off delayed, dependent on output 1
(e.g. fan control).
For Busch-Watchdog 180 flush-mounted Sensor Standard
6810-21x-101.
For Busch-Watchdog 180 flush-mounted sensor Comfort II
6800-xxx-104 and 6800-xxx-104M.
For Busch-Watchdog Presence tech 6813-xxx-101 und
6813/11-xxx.
For Busch-Remote control IR control cover 6066-xxx-10x
and 6067-xxx-10x.
For control cover 6430-xxx-10x and 6543-xxx-10x.
Combinable with Busch-Watchdog extension insert 6805 U.
Operation also possible via conventional push buttons
(2020 US, 2021/6 UK).
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Outputs: 2x Normally open contact, potential-bound
Suitable for: 230 V incandescent lamps, 230 V halogen
lamps, fluorescent lamps and low-voltage halogen lamps,
that are operated via transformers.
Rated current: 10 AX
Rated power: 2300 W/VA
Temperature range (Device): 0 °C to 35 °C
British Standard EN 60669-2-1
6402 U-500
6401-0-0051
1/10
19
14
14
Catalogue 2014/2015 | Remote control 545
Busch-Remote control IR
flush-mounted inserts
Product
Article-No.
Order-No.
Pack/Qty PG
Product
Busch-Universal master dimmer insert 1) 2) 3) 4)
Touch Dimmer
With light-level memory and intelligence for universal operation.
Selectable Soft-ON/OFF function and memory function.
Capacity expansion via output-side, parallel connectable
load line with a power module 6594 U up to 735 W/VA
possible.
For incandescent lamps, 230 V tungsten halogen lamps and
low-voltage halogen lamps with conventional transformers
or electronic transformers.
Short-circuit-proof, overload-protected.
With touch control.
Operation also possible via conventional push buttons
(2020 US, 2021/6 UK).
Without control cover.
For control cover with control lamp 6543-xxx-10x.
For Busch-Remote control IR control cover 6066-xxx-10x.
For comfort timer control element 6455-101-500.
For Busch-Watchdog 180 flush-mounted Sensor Standard
6810-21x-101.
For Busch-Watchdog 180 flush-mounted sensor Comfort II
6800-xxx-104 and 6800-xxx-104M.
For Busch-Watchdog Presence tech 6813-xxx-101 und
6813/11-xxx.
Combinable with Busch-Watchdog extension insert 6805 U.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Rated power: 60 - 420 W/VA
IEC 60669-2-1, British Standard EN 60669-2-1
6593 U-500
1)
2)
3)
4)
6590-0-0171
1/10
1
1) Non-illuminable.
2) Only in conjunction with standard flush-mounting boxes according to DIN 49073, Part 1, erect or
Busch-Jaeger No. 3040 wallbox stonework, 3050 wallbox cavity wall or 3060 wallbox concrete)
3) with integrated making-current limiter
1)
2)
3)
4)
19
5)
6)
7)
8)
9)
6512-0-0312
1/10
19
Illuminable with neon lamp. Neon lamp included in delivery with cover plate.
In the case of conventional transformers, take ~20% transformer loss into account.
In case of electronic transformers, 5 % transformer losses.
Only in conjunction with standard flush-mounting boxes according to DIN 49073, Part 1, erect or
Busch-Jaeger No. 3040 wallbox stonework, 3050 wallbox cavity wall or 3060 wallbox concrete)
For dimmable retrofit LED lamps (LEDi).
For dimmable retrofit LED lamps (LEDi) on conventional or electronic transformers.
Please check specification of transformer producers.
Recommendation: Please use loads and types of one producer.
A list of recommended Philips retrofit lamps LEDi is available at www.busch-jaeger-catalogue.com.
Busch-Blind control II switch insert 1) 2)
Suitable for blind, roller blind and awning drives with mechanical or electronic limit switch shut-off.
With two 230 V multi-way input terminals (Up/Down) for
group control.
With operating mode switch for the following modes: normal, louvre, base station, position.
With party function (disables the local control unit) in combination with Busch-Blind control II control cover 6430-xx-xxx,
6066-xx-xxx.
Wind alarm, cleaning functions can be accommodated via
extension input.
For control cover 6430-xx-xxx.
For IR control element 6066-xx-xxx.
For comfort timer control element 6455-101-500.
Running time: 3 min
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz/60 Hz
Outputs: 2x Normally open contact
Rated current: 3 A, cos φ 0.5
Rated power: 690 VA
Control/Signal outputs: 2
Temperature range (Device): 0 °C to 35 °C
6411 U-101-500
1) Suitable for multi-phase operation.
2) Compatible with types 6411 U/x.
546 Remote control | Catalogue 2014/2015
Pack/Qty PG
Busch-Dimmer® insert 1) 2) 3) 4) 5) 6) 7) 8) 9)
LED-Dimmer
Touch dimmer.
3 wire connection (neutral conductor required).
Optimized for dimming of Philips retrofit LEDs (LEDi).
For incandescent lamps, 230V tungsten halogen lamps and
low-voltage halogen lamps with conventional transformers
or electronic transformers and dimmable halogen energysaving lamps.
Mix operaton of LEDi with conventional loads possible.
Via mode switch adjustable between leading edge control
and trailing edge control.
Low-noise level by MOSFET transistors.
With electronic short-circuit protection.
With electronic overload protection.
With adjustable minimum brightness.
With light-level memory and minimum brightness memory.
Operation also possible via conventional push buttons
(2020 US, 2021/6 UK).
Without control cover.
For control cover with control lamp 6543-xxx-10x.
For Busch-Remote control IR control cover 6066-xxx-10x.
For comfort timer control element 6455-101-500.
For Busch-Watchdog Presence tech 6813-xxx-101 und
6813/11-xxx.
Combinable with Busch-Watchdog extension insert 6805 U.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz/60 Hz
Rated power: 2 - 100 W/VA
Protection class (Device): IP 20
Temperature range (Device): 0 °C to 35 °C
IEC 60669-2-1, British Standard EN 60669-2-1
6524 U-500
Busch-Memory touch-type controller 1) 2) 3)
3 wire connection (neutral conductor required).
For controlling ballast units for fluorescent lamps with control output 1-10 V DC, control current max. 50 mA DC.
For control cover with control lamp 6543-xxx-10x.
For Busch-Remote control IR control cover 6066-xxx-10x
and 6067-xxx-10x.
For comfort timer control element 6455-101-500.
For Busch-Watchdog 180 flush-mounted Sensor Standard
6810-21x-101.
For Busch-Watchdog 180 flush-mounted sensor Comfort II
6800-xxx-104 and 6800-xxx-104M.
For Busch-Watchdog Presence tech 6813-xxx-101 und
6813/11-xxx.
Combinable with Busch-Watchdog extension insert 6805 U.
Operation also possible via conventional push buttons
(2020 US, 2021/6 UK).
For LED control via control gears
Without control cover.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Rated power: 700 W/VA
IEC 60669-2-1, British Standard EN 60669-2-1
6550-0-0042
Order-No.
19
In the case of conventional transformers, take ~20% transformer loss into account.
In case of electronic transformers, 5 % transformer losses.
In conjunction with 6800-xxx-104 (M) a Soft Off can be adjusted.
Only in conjunction with standard flush-mounting boxes according to DIN 49073, Part 1, erect or
Busch-Jaeger No. 3040 wallbox stonework, 3050 wallbox cavity wall or 3060 wallbox concrete)
6550 U-101-500
Article-No.
6410-0-0394
1/10
19
Busch-Remote control IR
flush-mounted inserts
Product
Article-No.
Busch-Remote control IR
control elements
Order-No.
Pack/Qty PG
Product
Busch-Blind control II switch insert 1) 2)
Suitable for blind, roller blind and awning drives with mechanical or electronic limit switch shut-off.
With two 230 V multi-way input terminals (Up/Down) for
group control.
Connection possibility for brightness sensor 6414-101 and
burglar alert sensor 6413.
With operating mode switch for the following modes: normal, louvre, base station, position, awning.
With party function (disables the local control unit) in combination with Busch-Blind control II control cover 6430-xx-xxx,
6066-xx-xxx.
Wind alarm, cleaning functions can be accommodated via
extension input.
For control cover 6430-xx-xxx.
For IR control element 6066-xx-xxx.
For comfort timer control element 6455-101-500.
Running time: 3 min
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz/60 Hz
Outputs: 2x Normally open contact
Rated current: 3 A, cos φ 0.5
Rated power: 690 VA
Control/Signal outputs: 2
Temperature range (Device): 0 °C to 35 °C
6411 U/S-500-101
6410-0-0380
1/10
Order-No.
Article-No.
Pack/Qty PG
IR remote control
Battery-supplied infrared remote control.
For IR receiver (60xx).
For KNX presence detectors and KNX sensors with infrared
interface.
For switching/dimming up to 10 loads in 2 groups (1-5 /
6-10).
Programming and selection of 2 MEMO memories possible
per group.
Supply from 4 alkaline manganese batteries, IEC LR03
(microcell). Not included in delivery.
Range: 15 m
Rated voltage: 6 V6010-25-500
6020-0-1133
1
19
IR wall-mounted transmitter 1) 2)
Battery-supplied infrared remote control.
For IR receiver and KNX flush-mounted IR interfaces (selection of 2 memo functions for each address group and ALL
OFF).
Address group switch-over (1-5/6-10)
Supply: 6 V Flat-Pack battery (e.g. Duracell 7 K 67, not
included in delivery)
Range: 15 m
19
alpha
1) Suitable for multi-phase operation.
2) Compatible with types 6411 U/x.
20 platinum 3)
21 bronze 3)
24 studio white matt
24G studio white
6020-20
6020-21
6020-24-500
6020-24G-500
6020-0-0036
6020-0-0044
6020-0-1281
6020-0-1299
1/10
1/10
1
1
19
19
19
19
1) For programming the memory M1 and M2 the IR Mobile Remote Control 6010-xx is required.
2) For function together with KNX flush-mounted, infrared interface, see Technical Manual.
3) Surface painted.
IR wall-mounted transmitter 1)
1-channel
Battery-supplied infrared remote control.
For IR reception and KNX flush-mounted IR interface
(switching and dimming an IR address possible. ALL OFF
function for respective address group.).
Range: 15 m
Supply: 6 V Flat-Pack battery (e.g. Duracell 7 K 67, not
included in delivery)
alpha
20 platinum 2)
21 bronze 2)
24 studio white matt
24G studio white
6021-20
6021-21
6021-24-500
6021-24G-500
6020-0-0754
6020-0-0762
6020-0-1315
6020-0-1307
1
1
1
1
19
19
19
19
1) For function together with KNX flush-mounted, infrared interface, see Technical Manual.
2) Surface painted.
Fixing Bracket
For wall-mounted transmitter 6020-.../6021-...
For commercially available flush-mounted boxes.
6090
Technical information
www.BUSCH-JAEGER-catalogue.com
6099-0-0014
10
19
Catalogue 2014/2015 | Remote control 547
Busch-Remote control IR
control elements
Product
Article-No.
Order-No.
Pack/Qty PG
IR control element 1)
With marking, illuminated.
For LED-Dimmer insert 6524 U.
For Busch-Universal master dimmer insert 6593 U.
For Busch-Blind control II insert 6411 U-101,
6411 U/S-101.
For Busch-Universal 2gang 1way insert 6402 U.
for Busch-Universal touch-type controller 6550 U-101
Manual operation on-site and remote control via IR
remote control (6010-25) or wall-mounted transmitter
(6020-xx/6021-xx) possible.
72 ivory
74 alpine white
79 champagne
metallic 2)
774 studio white,
matt 2)
775 black matt 2)
777 blackberry 2)
783 aluminium silver 2)
6066-20-102
6066-21-102
6066-22G-102
6066-24-102-500
6066-24G-102-500
6066-260-102
6066-266-102
6020-0-1316
6020-0-1317
6020-0-1318
6020-0-1371
6020-0-1372
6020-0-1365
6020-0-1366
10
1/10
1/10
1
1
1/10
1/10
19
19
19
19
19
19
19
impuls
6066-72-101
6066-74-101-500
6020-0-1385
6020-0-1190
1
1
19
19
6066-79-101
6020-0-0606
1
19
6066-774-101-500
6066-775-101-500
6066-777-101
6066-783-101
6020-0-1406
6020-0-1402
6020-0-1391
6020-0-1386
1
1
1
1
19
19
19
19
IR control element 1)
With marking, illuminated.
For LED-Dimmer insert 6524 U.
For Busch-Universal master dimmer insert 6593 U.
For Busch-Blind control II insert 6411 U-101,
6411 U/S-101.
For Busch-Universal 2gang 1way insert 6402 U.
for Busch-Universal touch-type controller 6550 U-101
Manual operation on-site and remote control via IR
remote control (6010-25) or wall-mounted transmitter
(6020-xx/6021-xx) possible.
72 ivory
74 alpine white
79 champagne
metallic 1)
774 studio white,
matt 1)
775 black matt 1)
777 blackberry 1)
783 aluminium silver 1)
1/10
10/10
1/10
1/10
19
19
19
19
6066-884
6066-885
6020-0-1397
6020-0-1399
1/10
1/10
19
19
solo®
6066-82
6066-84
6066-803
6066-815
6020-0-1332
6020-0-1334
6020-0-1395
6020-0-1393
10/10
1/10
1/10
1/10
19
19
19
19
84 studio white
896 chalet-white
Busch-axcent®
6066-84
6066-896-500
6020-0-1334
6020-0-1411
1/10
1/10
19
19
81 anthracite
82 ivory white
84 studio white
carat®
6066-81
6066-82
6066-84
6020-0-1379
6020-0-1332
6020-0-1334
1/10
10/10
1/10
19
19
19
866 stainless steel
pure stainless steel
6066-866
6020-0-1389
1/10
19
548 Remote control | Catalogue 2014/2015
10
10
10
1
1
1/10
1/10
19
19
19
19
19
19
19
impuls
6067-72-101
6067-74-101-500
6020-0-1387
6020-0-1224
1
1
19
19
6067-79-101
6020-0-0986
1
19
6067-774-101-500
6067-775-101-500
6067-777-101
6067-783-101
6020-0-1408
6020-0-1404
6020-0-1392
6020-0-1388
1
1
1
1
19
19
19
19
6067-81
6067-82
6067-83
6067-84
6020-0-1380
6020-0-1333
6020-0-1384
6020-0-1335
1/10
1
1/10
1
19
19
19
19
6067-884
6067-885
6020-0-1398
6020-0-1400
1/10
1/10
19
19
solo®
6067-82
6067-84
6067-803
6067-815
6020-0-1333
6020-0-1335
6020-0-1396
6020-0-1394
1
1
1/10
1/10
19
19
19
19
84 studio white
896 chalet-white
Busch-axcent®
6067-84
6067-896-500
6020-0-1335
6020-0-1412
1
1/10
19
19
81 anthracite
82 ivory white
84 studio white
carat®
6067-81
6067-82
6067-84
6020-0-1380
6020-0-1333
6020-0-1335
1/10
1
1
19
19
19
866 stainless steel
pure stainless steel
6067-866
6020-0-1390
1/10
19
82
84
803
815
ivory white
studio white
grey metallic 1)
yellow
1) Surface painted.
1) Touch-type Controller 6550 U-101 non-illuminable
2) Surface painted.
6020-0-1324
6020-0-1325
6020-0-1326
6020-0-1373
6020-0-1374
6020-0-1369
6020-0-1370
future® linear
anthracite
ivory white
aluminium silver 1)
studio white
studio white,
matt 1)
885 black matt 1)
6020-0-1379
6020-0-1332
6020-0-1383
6020-0-1334
ivory white
studio white
grey metallic 2)
yellow
6067-20-102
6067-21-102
6067-22G-102
6067-24-102-500
6067-24G-102-500
6067-260-102
6067-266-102
IR control element
With marking, illuminated.
For Busch-Universal relay switch insert 6401 U-10x and
Busch-Universal 2gang 1way insert 6402 U.
Manual operation on-site and remote control via IR
remote control (6010-25) or wall-mounted transmitter
(6020-xx/6021-xx) possible.
81
82
83
84
884
6066-81
6066-82
6066-83
6066-84
82
84
803
815
Pack/Qty PG
1) Surface painted.
future® linear
anthracite
ivory white
aluminium silver 2)
studio white
studio white,
matt 2)
885 black matt 2)
Order-No.
alpha
20 platinum 1)
21 bronze 1)
22G ivory
24 studio white matt
24G studio white
260 palladium 1)
266 titanium 1)
1) Touch-type Controller 6550 U-101 non-illuminable
2) Surface painted.
81
82
83
84
884
Article-No.
IR control element
With marking, illuminated.
For Busch-Universal relay switch insert 6401 U-10x and
Busch-Universal 2gang 1way insert 6402 U.
Manual operation on-site and remote control via IR
remote control (6010-25) or wall-mounted transmitter
(6020-xx/6021-xx) possible.
alpha
20 platinum 2)
21 bronze 2)
22G ivory
24 studio white matt
24G studio white
260 palladium 2)
266 titanium 2)
Product
Busch-Remote control IR built-in/
socket outlet receiver
Product
Article-No.
Order-No.
Pack/Qty PG
Busch-Blind control II built-in unit 1) 2)
2gang
For joint switching of 2 blind drives via a 230 V multi-way
input terminal.
Additional IR remote control via IR flying receiver
6045 E-101 possible.
Control via IR mobile remote control/wall-mounted transmitter 6010-25 and 6020/21-xxx
Rated voltage: 230 V~
Rated frequency: 50 Hz
Outputs: 4x Normally open contact
Rated current: 3 A, cos φ 0.5
Rated power: 690 VA
Temperature range (Device): 0 °C to 35 °C
6420 EB-500
6420-0-0020
1
Product
Order-No.
Article-No.
Pack/Qty PG
IR Switch
with adapter plug
For incandescent lamps, 230 V tungsten halogen lamps,
fluorescent lamps and low-voltage halogen lamps, that are
operated via transformers.
Socket outlet ready for connection.
Control only possible via hand-held or wall-mounted transmitter 6010-xx/6020-xx/6021-xx.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Rated power: 2300 W
24 studio white
6080-24-500
6020-0-1166
1
19
19
1) Suitable for multi-phase operation.
2) Individual operation of the blinds is possible using infrared remote control (e.g. 6010-25).
IR receiver 1)
4gang
For switching 4 consumers
Operation also possible via 2 conventional push buttons
(2020 US/2021/6 US).
Central disablement of all outputs possible.
Additional IR remote control via IR flying receiver
6045 E-101 possible.
Control via IR mobile remote control/wall-mounted transmitter 6010-25 and 6020/21-xxx
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Outputs: 4x Normally open contact, potential-bound
Rated current: 6 A, cos φ 1
Rated current: 3 A, cos φ 0.5
Temperature range (Device): 0 °C to 35 °C
6056 EB-500
6020-0-1232
1
19
1) Push-switch operation possible via additional wire bridge.
IR flying receiver 1)
For controlling the built-in devices: 6420 built-in/6056 builtin.
With approx. 0.5 m supply lead.
Length of the linear lamp: 30 mm
Control only possible via hand-held or wall-mounted transmitter 6010-xx/6020-xx/6021-xx.
6045 E-101-500
6020-0-1240
1
19
1) Feed line cannot be extended.
IR dimmer 1-10 V
For luminaires.
For controlling ballast units for fluorescent lamps with control output 1-10 V DC, control current max. 50 mA DC.
Control only possible via hand-held or wall-mounted transmitter 6010-xx/6020-xx/6021-xx.
Rated voltage: 230 V~, +10 % / -10 %
Rated frequency: 50 Hz
Rated power: 500 W
Temperature range (Device): 0 °C to 60 °C
6045-500
Technical information
www.BUSCH-JAEGER-catalogue.com
6020-0-1265
1
19
Catalogue 2014/2015 | Remote control 549
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement