2016 Novaris Product Handbook
Global Solutions in Lightning and Surge Protection
72 Browns Road Kingston
P.O. Box 2010 Kingston
Tasmania 7050 Australia
Telephone: +61 3 6229 7233
Facsimile: +61 3 6229 9245
Email: Web Page: © Copyright 2016
[email protected]
www.novaris.com.au
PRODUCT HANDBOOK 2016
Distributed By:
Global Solutions in
Lightning and Surge Protection
PRODUCT HANDBOOK
Novaris
Novaris Pty Ltd
Glossary
PhPhase
Iimp
Defined by three parameters, a current peak value, a charge and a specific energy.
Generally relates the IEC definition of a direct lightning strike modelled by a 10/350µs
waveshape. This is used for the classification of SPDs for test class I in accordance with
T h e U l t i m a t e H i g h Vo l t a g e Te s t
IEC61643-11.
Q
Charge contained in a test waveform. Expressed in coulombs (As).
W/R
Specific Energy relating to a test waveform. Expressed in kJ/µs.
Imax
Defined as the peak value of a current through the SPD having an 8/20µs waveshape.
This is used for the classification of SPDs for test class II in accordance with IEC61643-11.
This is generally recognized for MOV based SPDs as the single shot impulse rating.
In
Defined as the peak value of a current through the SPD having an 8/20µs waveshape. This
is used for the classification of SPDs for test class II in accordance with IEC61643-11. This
is known as the nominal discharge current and is generally recognized for MOV based
SPDs as the rating of the SPD for 15 such impulses.
IL
The maximum continuous RMS or DC current that can be supplied to a load connected to a
two port or series connected SPD.
If
The current supplied by the electrical power system which flows through an SPD after a
discharge current impulse. This is called the follow-on current and is particularly applicable
to voltage switching type SPDs such as spark gaps and gas discharge tubes.
Ifi
Follow-on current interrupting rating. This is the maximum AC RMS current that a voltage
switching SPD such as a spark gap can interrupt.
U0
The RMS line to neutral voltage of the power system.
U c
The maximum RMS or DC voltage, which may be continuously applied to an SPD.
U p
The let through voltage of an SPD defined for a specified test waveform.
tA
Response time of an SPD to a defined test waveform.
DU
Voltage drop of a two port SPD at rated current expressed as a percentage of U0.
f c
The maximum usable frequency.
Photographer: Renee Doyle
Q1 Building - Gold Coast, Queensland AUSTRALIA
Lightning Protection Consultants:
Surge Protection Design and Manufacture:
Powercom Consultants Pty Ltd
Novaris Pty Ltd
This was the ultimate high voltage test of The Novaris Systematic Approach
to lightning and surge protection.
Jan 2016
59
The Novaris Systematic Approach
Lightning strikes are an unpredictable natural phenomenon. However the way equipment can be protected
from lightning strikes is predictable. The ‘Novaris Systematic Approach’ is a step-by-step solution to lightning
and surge protection that can be applied to any application.
1
Define Boundaries
2
Protect Structure
Boundaries divide areas of different potential.
Novaris supports conventional lightning protection methods.
Install Bonded Earthing System
Protect Power Lines
Protect Signal/Data Lines
3
4
5
A single bonded earthing system within each boundary is essential.
Protect all power lines crossing protection boundaries.
Protect all signal/data lines crossing protection boundaries.
Novaris offers:
Investigation and Analysis
- Novaris offers a complete package from analysis of your existing lightning and surge
protection system to providing complete recommendations based on site surveys
and technical analysis.
Structural Lightning Protection and Earthing Systems
- design and advice on lightning protection systems for all structures in accordance
with recognised world standards.
- supply of structural lightning protection and earthing components.
A Comprehensive range of Surge Protection Products to suit any application
- ranging from main switchboard and distribution board surge protection,
PLC and control system protection, to RF coaxial protection.
Custom Product Design
- our innovative R&D team can engineer a surge protection solution
for even the most demanding of applications.
Project Management & Installation
- Novaris actively seeks consultancy, project management and installation work.
Our experience extends from Australia to the Pacific, Asia, Africa and the Middle East.
1
Key Product Features
IEC
Compliant
All Mode
Protection
Compliant with the relevant IEC lightning and surge protection
standards, in particular IEC 62305 and IEC 61643.
Novaris models featuring all mode protection provide protection for
all combinations of lines (L-N, L-E, N-E) ensuring the maximum level
of protection is achieved at all times. They have been designed for
installation in any wiring system worldwide.
Multistage
Transient
Protection
Models featuring multistage transient protection deliver greater levels
Redundant
Segments
Models featuring redundant segments have a parallel redundant
Thermal
Sensing
Percentage
Active Display
LED Status
Display
SIP and
External Alarms
of protection through a staged approach. The primary stage absorbs
the majority of the surge energy. The remaining stages provide
accurate clamping and a degree of redundancy.
arrangement of high energy metal oxide varistors (MOVs), thus
promoting long life and exceptional surge handling capacity.
Sustained overvoltages can cause components to overheat and
degrade. Thermal sensing warns of this condition.
A digital display confirms the device rating upon switch on, then
displays percentage active. The display indicates segment status and
thermal overload.
LED indicators are provided to indicate operating status.
The Novaris Surge Indicator Panel (SIP) allows remote monitoring
of any Novaris product featuring external alarms. Models featuring
external alarms have voltage free changeover contacts (SPDT) for
remote status indication.
2
DIN 43880
Compliant
Protection devices housed in DIN 43880 compliant enclosures allow
Safe Metal
Enclosure
Novaris surge protection products are housed in safe, all metal
for convenient installation on DIN rail fittings commonly used in
switchboards worldwide.
enclosures. In the event of a prolonged overvoltage they will not catch
fire or explode.
Power Protection
Surge Diverters
6
Table Of Contents
Novaris Systematic Approach
1
Key Product Features
2
Table of Contents
3
Selecting Power Protection
4
Surge Diverters
6
Spark Gaps
12
Hybrid Spark Gaps
13
Series Surge Protectors
14
Surge Filters
16
Selecting Process Control Protection
25
Process Control Protectors
26
Surge Protection Tester
34
LAN & CCTV Protectors
35
CCTV Protectors
36
LAN Protectors
37
Selecting Coaxial Protection
39
Coaxial Surge Protectors
40
Telephone Protection
44
High Surge Current Signal Line Protectors
46
Special Products
47
Power Protection
Surge Filters
16
Process Control
Protection
26
LAN & CCTV
Protection
35
Coaxial Protection
40
Telephone Protection
Additional Information
Standards and Safety
52
Risk Assessment
53
Surge Ratings
54
Installation
56
58
Signalling Protocols
Glossary
44
Special Products
59
47
NOTE:
Due to the Novaris policy of continuing product development, specifications are subject to change without notice.
Additional
Information
54
3
Selecting Power Protection
Power line surge protection must:
1. Provide adequate protection for all equipment.
2. Achieve a long working life.
3. Optimise the cost and size of the surge protection devices (SPDs).
Options for Surge Protection Devices
There are two common configurations of SPDs:
SPD
One port SPDs are parallel or shunt connected across the line. These include the Novaris SD, SG and
HSG products.
Two port SPDs are connected in series with the line. These include the Novaris SSP, SF and PP products.
SPD
There are two classes of SPD components:
Voltage limiting SPDs include metal oxide varistors and suppressor diodes. These have a high impedance
when no surge is present but can reduce impedance continuously with increased surge current and
voltage. These are also called “clamping devices”. Novaris SD, SSP, SF and PP products are voltage
clamping SPDs.
Voltage switching SPDs include spark gaps, gas discharge tubes, thyristors and triacs. These have a high
impedance when no surge is present but can have a sudden change to a low impedance in response
to a voltage surge. These are also called “crowbar devices”. The Novaris SG products are voltage
switching SPDs.
Sometimes a combination of these components may be used. The Novaris HSG is an example of a
combination SPD.
Selection of Surge Protection Devices
1. Surge Diverters, SD
All Novaris surge diverters with initial product code SD employ metal oxide varistor (MOV) voltage limiting
components. These can be used for main switchboard primary protection, distribution board and final
circuit protection. As voltage limiting components there is no follow on current, and with suitable fusing
U
these are easy to install and operate.
SD products are suitable for all applications except where extreme voltage fluctuations may be
experienced. Excessive overvoltage can damage MOV based SPDs although all Novaris surge diverters
are housed in metal enclosures and meet the fail-safe requirements of UL1449 - specifically package
rupture and the effects of excessive heating.
Novaris manufactures surge diverters to suit all applications from high exposure environments to final
circuit protection with ratings of Imax up to 200kA (8/20µs) or Iimp up to 50kA (10/350µs)*.
Like all one port shunt connected SPDs, performance can be compromised by the presence of long
connecting leads, particularly in physically large main switchboards. For this reason primary SPDs on
main switchboards should be followed by secondary protection on distribution boards and final circuits.
4
Selecting Power Protection
2. Spark Gaps, SG
Spark gaps have high surge ratings and are suitable for point of entry protection in installations with
highly exposed overhead LV power lines with no local transformer in high lightning areas. As voltage
switching SPDs, spark gaps have a crowbar effect and effectively place a short circuit across the
line once fired. Thus high levels of AC follow on current will flow. Unless properly configured to be
compatible with the AC fault rating of the supply and suitably fused, spark gaps can cause nuisance
tripping of supply circuit breakers and extreme voltage disturbances whilst the follow on current flows.
Novaris spark gap SPDs have surge ratings (Iimp) of up to 110kA (10/350µs). Triggered spark gaps must
be followed by secondary protection further downstream in the distribution network because they have
a high impulse firing voltage.
3. Hybrid Spark Gaps, HSG
Hybrid spark gaps combine the best qualities of voltage switching and voltage limiting components.
Novaris HSG hybrid spark gaps are suitable for all high exposure installations and meet the
recommendations of IEC61643-12 in relation to surge ratings with Imax of 200kA (8/20µs) or Iimp of 25kA
U
(10/350µs)*. The spark gap in the HSG is a high energy gas discharge tube with a clearly defined impulse
firing voltage, its let through voltage closely approaches that of an MOV based surge diverter.
The hybrid combination ensures that there is no follow on current and the HSG may be as easily
deployed as our SD range. The HSG is able to tolerate excessive temporary overvoltages (TOV) and is
ideal for applications where mains voltages fluctuations are significant.
4. Series Surge Protector, SSP
All shunt connected SPDs are compromised in performance by the presence of their interconnecting
leads. Typically voltage drops of 500V per meter of connecting lead can be expected. Such lead lengths
are often unavoidable in physically large main switchboards. Nevertheless one port SPDs provide
U
effective protection for the main switchboard.
For circuits that are more sensitive the SSP provides a means of eliminating the shunt connected leads
and places the SPD directly across the line. Such applications might include UPS inputs, rectifiers,
VSDs and motors.
5. Surge Filters, SF
The surge filter is a true two port SPD offering an extremely low let through voltage capable of protecting
Z
the most sensitive of electronic circuits. The Novaris range of surge filters is extensive: from 2A DIN rail
U
U
mount units designed to protect sensitive PLCs and process equipment; plug in units for final circuit
outlets; to 2000A per phase filters designed to protect major data centres.
Surge ratings up to 200kA (8/20µs) are available making surge filters suitable for providing primary
and secondary protection in one package as may be required at a cellular basestations, process plant
control rooms or data centres. As surge filters are series connected they must have a current rating IL
equal to or greater than the protected circuit.
*Surge Ratings: tests conducted by some manufacturers and informally reported to the IEEE have indicated that the stress imposed on an
MOV based SPD by a 10/350µs impulse might be equivalent to the stress imposed by a standard 8/20µs impulse, with a scaling factor of
10. Thus an SPD with Iimp=25kA could be equivalent to Imax= 200kA. From IEEE Std C62.41.2-2002.
5
POWER PROTECTION - Surge Diverters
SD Surge Diverters
Novaris MULTIMOV MSB surge diverters offer unsurpassed safety, quality
and reliability in protection for your electrical system. MULTIMOV surge
diverters are an ideal point-of-entry protector for all industrial, commercial
and communications applications.
SD 1 - 100 - 275 - [*]
SD3-200-275
SD3-150-275
SD3-100-275
SD1-200-275
Options Uc
SD1-150-275
SD1-100-275
Product Series Phase Imax
Electrical Specifications
Connection Type
Shunt
Modes of protection
L-N
Phases
1
Nominal voltage
U0
Maximum continuous voltage
Uc
Maximum discharge current (8/20µs)
Imax
3
230V / 50Hz (110V / 60Hz by request)
275V / 50Hz (130V / 60Hz by request)
100kA
150kA
200kA
100kA
150kA
Nominal discharge current (15 x 8/20µs)
In
40kA
60kA
80kA
40kA
60kA
80kA
Voltage protection level @ 3kA (8/20µs)
Up
<800V
<750V
<700V
<800V
<750V
<700V
Response time
tA
80A
100A
<5ns
Earth leakage current
<5µA
Display
7-segment LED, percentage active
Alarms
Segment / thermal failure, clean SPDT contact
Alarm isolation to active circuitry
Maximum backup fuse (gG)
4kV
63A
80A
100A
63A
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Terminal capacity - power
16mm2
Terminal capacity - alarm
2.5mm2
Terminal screw torque - power
1.0Nm
Terminal screw torque - alarm
0.5Nm
Environmental
Mounting
IP 20
Panel mount / TS35 DIN
Enclosure / Colour
Weight
Panel mount
Metal / Black
500g
2.0kg
Width
54mm
200mm
Height
140mm
200mm
Depth
68mm
79.5mm
Dimensions
6
Standards Compliance
Options [*]
IEC 61643-11 class I
Neutral-earth protection (non-MEN, same dimensions)
N
AS/NZS 1768 category C
Metal enclosure
M
IEEE C62.41 category C
Polycarbonate enclosure
P
IEC 1000-4-5
Extended operating voltage (95-415V / 50Hz)
X
UL1449 fourth edition
Over / under voltage relay
O
Non-MEN version ( L-PE)
U
A-tick
200kA
POWER PROTECTION - Surge Diverters
SDN All Mode Surge Diverters
Novaris SDN Surge Diverters are the ideal choice for all mode protection in
major distribution switchboards. Being all mode the SDN is particularly
suitable for main switchboards in non MEN installations.
SDN 3 -100- 275 - [*]
SDN3-200-275
Options Uc
SDN3-150-275
SDN3-100-275
Product Series Phase Imax
Electrical Specifications
Connection type
Shunt
Modes of protection
All mode (L-N, L-PE, N-PE)
Phases
3
230V / 50Hz (110V / 60Hz by request only)
Nominal voltage
U0
Maximum continuous voltage
Uc
Maximum discharge current (8/20µs)
Imax
100kA
Nominal discharge current (15 x 8/20µs)
In
40kA
Voltage protection level @ 3kA (8/20µs)
Up
Response time
tA
275V / 50Hz (130V / 60Hz by request only)
150kA
200kA
60kA
80kA
<800V
<5ns
Earth leakage current
<10µA
Display
LED, status
Alarms
Segment / thermal failure, clean SPDT contact
Alarm isolation
Maximum backup fuse (gG)
4kV
63A
80A
100A
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Terminal capacity - power
16mm2
Terminal capacity - alarm
2.5mm2
Terminal screw torque - power
1.0Nm
Terminal screw torque - alarm
0.5Nm
Environmental
IP 20
Mounting
Panel mount / TS35 DIN
Enclosure / colour
Weight
Metal / Black
650g
725g
800g
Dimensions
Width
80mm
Height
140mm
Depth
68mm
Options [*]
Standards Compliance
Metal enclosure
M
IEC 61643-1 class I
Polycarbonate enclosure
P
AS/NZS 1768 categories B, C
Extended operating voltage (95-415V / 50Hz)
X
IEEE C62.41 categories B, C
Over / under voltage relay
O
IEC 1000-4-5
Surge Counter
C
UL1449 fourth edition
HRC Fusing
H
7
POWER PROTECTION - Surge Diverters
SDD Surge Diverter DIN
Novaris SDD Surge Diverters DIN offer powerful performance at domestic
MSB and industrial DBs. The SDD diverters are housed in DIN 43880
compliant, fail-safe metal enclosures and are fully compliant to AS/
NZS1768-2007 and to AS/NZS3000 wiring rules.
SDD 1 - 50 - 275 - [*]
SDD3-100-275-A
SDD3-100-275
SDD3-50-275-A
SDD3-50-275
SDD3-20-275
SDD1-100-275-A
SDD1-100-275
SDD1-50-275-A
Options Uc
SDD1-50-275
SDD1-20-275
Product Series Phase Imax
Electrical Specifications
Connection type
Shunt
Modes of protection
All mode (L-N, L-PE, N-PE)
Phases
Nominal voltage
1
3
230V / 50Hz
U0
275V / 50Hz
Maximum continuous voltage
Uc
Maximum discharge current (8/20µs)
Imax
20kA
50kA
100kA
In
10kA
20kA
40kA
Nominal discharge current (15 x 8/20µs)
20kA
50kA
100kA
10kA
20kA
40kA
ISCCR
25kA
Voltage protection level @ 3kA (8/20µs)
Up
<800V
Response time
tA
Maximum switchboard fault rating
<5ns
Earth leakage current
<10µA
Display
LED status per phase
Alarms (optional)
Power fail safe, thermal overload, SPDT voltage free contact
Alarm isolation
Maximum backup fuse (gG)
4kV
16A
32A
63A
16A
32A
63A
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Terminal capacity - power
16mm2
Terminal capacity - alarms
2.5mm2
Terminal screw torque - power
1.0Nm
Terminal screw torque - alarm
0.5Nm
Environmental
IP 20
Mounting
TS35 DIN rail
Enclosure / Colour
Weight
Metal / black
120g
150g
230g
250g
260g
300g
355g
370g
485g
495g
Dimensions
Width
Standards Compliance
IEC 61643-11 class II
8
18mm
36mm
54mm
Height
95mm
Depth
70mm
AS/NZS 1768 categories B, C
Options [*]
IEEE C62.41 categories B, C
External alarm
UL1449 fourth edition
Polycarbonate enclosure
N/A
Standard
A
N/A
Standard
P
A
72mm
Standard
A
Standard
POWER PROTECTION - Surge Diverters
SDD2 DINsafe Surge Diverters
Novaris SDD2 Surge Diverters offer an ideal solution for DC and two phase
systems. The SDD2 diverters are housed in a DIN compliant, fail-safe
metal enclosure.
SDD2 - 10 - 18 - DC
SDD2-100-150-DC
SDD2-50-150-DC
SDD2-10-18-DC
SDD2-32-65-DC
AC / DC
Uc
SDD2-10-45-DC
Product Series Imax Electrical Specifications
Connection Type
Shunt
Modes of protection
Common and transverse modes or L1-PE and L2-PE
Phases / poles
2
AC / DC
DC
Nominal voltage
U0
12V
24V
48V
110V
Maximum continuous voltage
Uc
18V
45V
65V
150V
<150V
<190V
Maximum discharge current (8/20µs)
Imax
Voltage protection level @ 3kA (8/20µs)
Up
Response time
tA
10kA
<80V
32kA
100kA
<400V
<5ns
Earth leakage current
<10µA
Display
Maximum backup fuse (gG)
50kA
LED status
10A
10A
20A
32A
63A
Mechanical Specifications
Operating temperature / humidity
Standards Compliance
IEC 61643-1 class II, III
-40°C to +70°C / 5 to 95% non-condensing
Terminal capacity
16mm2
Terminal screw torque
1.0Nm
Environmental
IP 20
Mounting
TS35 DIN rail
Enclosure / colour
Metal / Black
Weight
500g
AS/NZS 1768 categories A, B
Dimensions
IEEE C62.41 categories A, B
Width
72mm
IEC 1000-4-5
Height
95mm
UL1449 fourth edition
Depth
80mm
9
POWER PROTECTION - Surge Diverters
SDPV Surge Diverters - Photovoltaic
Novaris SDPV surge diverters provide the highest level of protection for
photovotaic equipment with voltages up to 1000V. Their compact design
makes them an ideal choice for space restricted applications.
SDPV - 40 - 1000 - A[*]
SDPV-40-600-A
SDPV-40-1000-A
Product Series Options ImaxUc
Electrical Specifications
Connection type
Series
Modes of protection
All mode ((+)-(-), (+)-PE, (-)-PE)
Phases
2
600V
1000V
Maximum open circuit voltage
Ucpv
Maximum discharge current (8/20µs) (L-N)
Imax
40kA transverse mode, 80kA common mode
Nominal Discharge Current (8/20μs)
In
20kA transverse mode, 40kA common mode
Voltage protection level @ 3kA (8/20µs)
UP
Response time
tA
Earth leakage current
<2000V
<3000V
Instantaneous
<200µA
Display
LED status
Alarms
Thermal failure
Alarm isolation to active circuitry
4kV
Maximum backup fuse (gG) ( >63A DC current)
Mechanical Specifications
Operating temperature / humidity
Connection type
-40 to +70ºC / 5 to 95% non-condensing
Screw terminal
Terminal capacity - power
16mm2
Terminal capacity - alarm
2.5mm2
Terminal screw torque - power
2.0Nm
Terminal screw torque - alarm
0.5Nm
Environmental
IP 20
Mounting
TS35 DIN rail
Enclosure / colour
Metal / Black
Weight
400g
Dimensions
Standards Compliance
Width
90mm
Height
95mm
Depth
70mm
IEC 61643-31
Options [*]
prEN 50539-11
Polycarbonate enclosure
10
P
POWER PROTECTION - Surge Diverters
SDH High Voltage Surge Diverters
Novaris SDH High Voltage Surge Diverters have been engineered for system
voltages above 600VRMS. Typical applications include aviation runway
lighting, mining and railway industries.
SDH - 100 - 2000 - [*]
SDH-100-2000
SDH-100-1500
Options Uc
SDH-200-1000
SDH-100-550
Product Series Imax
Electrical Specifications
Connection type
Shunt
Modes of protection
L-PE
Phases
1
Maximum continuous voltage
Uc
550V
1000V
Maximum discharge current (8/20µs)
Imax
100kA
200kA
Voltage protection level @ 3kA (8/20µs)
Up
1.6kV
2.6kV
Response time
tA
1500V
2000V
100kA
3.8kV
4.8kV
<5ns
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Terminal capacity
25mm2
Terminal screw torque
2.5Nm
Environmental
IP 20
Mounting
Enclosure / colour
Weight
See mounting options below
ABS, ceramic / Blue
2.0kg
Dimensions
Width
57mm
Height
214mm
Depth
162mm
Options [*]
GEC RSL63H mounting
H
Standards Compliance
GEC RSL63P mounting
P
IEC 61643-11 class I
GEC RSL63PH mounting
PH
AS/NZS 1768 category C
External alarm
A
IEEE C62.41 category C
External alarm / Themal disconnect
T
11
POWER PROTECTION - Spark Gaps
SG Spark Gap Arresters
Novaris SG Spark Gap Arresters have high surge ratings suitable for point of
entry protection in installations with highly exposed overhead LV power
lines with no local transformer. These are triggered spark gaps resulting in
relatively low let through voltages sufficient to protect switchgear in main
switchboards.
SG 1 - 50 - 275 - [*]
ECD-100-600
SGN-100-275
SG3-50-255
SG1-50-255
SG3-110-275
Options Uc
SG1-110-275
Product Series Phase Iimp
Electrical Specifications
Connection type
Shunt
Modes of protection
L-N
L-N
N-PE
1
3
-
Phases
230V / 50Hz
Nominal voltage
U0
Maximum continuous voltage
Uc
255V / 50Hz
275V / 50Hz
255V / 50Hz
275V / 50Hz
-
Interrupting follow current @ Uc
Ifi
3kARMS
50kARMS
3kARMS
50kARMS
100ARMS
Lightning impulse voltage sparkover (1.2/50µs)
Up
<1.3kV
<2.5kV
<1.3kV
<2.5kV
<1.5kV
Maximum impulse current (10/350µs)
Iimp
50kA
110kA
50kA
110kA
100kA
Q
25As
55As
25As
55As
50As
Specific energy
Charge
W/R
600kJ/W
3000kJ/W
600kJ/W
3000kJ/W
2500kJ/W
Response time
tA
Maximum backup fuse (gG)
<100ns
315A
500A
Terminal capacity
35mm2
Lug Ø10
Terminal screw torque
2.5Nm
Environmental
IP 20
315A
500A
-
Mechanical Specifications
Operating temperature / humidity
Mounting
-40 to +70ºC / 5 to 95% non-condensing
TS35 DIN
Enclosure / colour
Weight
35mm2
Lug Ø10
2.5Nm
35mm2
16mm2
2.5Nm
2.0Nm
IP 00
IP 20
IP 00
IP 20
Panel
TS35 DIN
Panel
TS35 DIN
Flame retardant Polyamide 6 / Black
230g
1.0kg
690g
3.0kg
Metal/Black
210g
300g
Dimensions
Standards Compliance
IEC 61643-11 class I
AS/NZS 1768 category C
12
Width
36mm
67mm
106mm
201mm
Height
90mm
150mm
90mm
150mm
90mm
36mm
95mm
Depth
67mm
94mm
67mm
94mm
67mm
70mm
Options [*]
IEEE C62.41 category C
Neutral-earth protection
IEC 1000-4-5
Metal enclosure
UL1449 fourth edition
Over / under voltage relay
N
M
O
-
POWER PROTECTION - Hybrid Spark Gaps
HSG Hybrid Spark Gap Arresters
Novaris HSG Hybrid Spark Gap Arresters combine the best qualities of voltage
switching and voltage limiting components. Novaris HSG hybrid spark
gaps suit all high exposure installations. There is no follow on current.
The HSG is ideal for applications where mains voltages fluctuations are
significant.
HSG 1 - 25 - 480 - [*]
HSG3-25-480
Options Uc
HSG1-25-480
Product Series Phase Iimp
Electrical Specifications
Connection type
Shunt
Modes of protection
L-N
Phases
1
3
Nominal voltage
U0
230V / 50Hz
Maximum continuous voltage
Uc
480V / 50Hz
Interrupting follow current @ Uc
Ifi
-
Lightning impulse voltage sparkover (1.2/50µs)
Up
<1.1kV
Maximum impulse current (10/350µs)
Iimp
25kA
Maximum discharge current (8/20µs)
Imax
250kA
Charge
Q
12.5As
Specific energy
W/R
625kJ/W
Response time
tA
<100ns
Display
LED status
Alarms
Clean SPDT contact
Alarm isolation to active circuitry
4kV
Maximum backup fuse (gG)
125A
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95%
Terminal capacity - power
16mm2
Terminal capacity - alarms
2.5mm2
Terminal screw torque - power
1.0Nm
Terminal screw torque - alarms
0.5Nm
Environmental
Mounting
IP 20
Panel mount / TS35 DIN
Enclosure / colour
Weight
Metal / Black
1.2kg
5.0kg
Dimensions
Standards Compliance
Width
60mm
240mm
Height
200mm
260mm
Depth
70mm
78mm
IEC 61643-11 class I
Options [*]
AS/NZS 1768 category C
Neutral-earth protection
N
IEEE C62.41 category C
Metal enclosure
M
IEC 1000-4-5
Surge Counter
C
UL1449 fourth edition
Over / under voltage relay
O
13
POWER PROTECTION - Series Surge Protectors
SSP Surge Protectors - Single Phase
Novaris SSP protectors are suitable for installation in circuits up to 63A. The
SSP range has been engineered to provide excellent performance and
installation independent let-through voltage. Their compact design makes
them an ideal choice for space restricted applications.
SSP 1- 63 -100 - 275 -[*]
SSP1-63-50-275
SSP1-63-100-275
SSP1-32-100-275
50kA
100kA
50kA
100kA
20kA
40kA
20kA
40kA
SSP1-32-50-275
SSP1-20-100-275
SSP1-20-50-275
SSP1-16-15-275
Product Series Options PhaseUc
IL Imax
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Phases
1
Nominal voltage
U0
230V / 50Hz
Maximum continuous voltage
Uc
275V / 50Hz
Maximum load current
Maximum discharge current (8/20µs)
IL
16A
Imax
15kA
50kA
20A
100kA
32A
6kA
20kA
40kA
Nominal discharge current (15 x 8/20μs)
In
Voltage protection level @ 3kA (8/20µs)
UP
<800V
Response time
tA
<5ns
Earth leakage current
<500µA
63A
<10µA
Display
LED status
Alarms (optional)
-
Alarm isolation to active circuitry
-
Maximum backup fuse (gG)
Segment / thermal failure, clean SPDT contact
4kV
16A
20A
32A
63A
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Connection type
Screw terminal
Terminal capacity - power
2.5mm2
16mm2
Terminal capacity - alarm
-
2.5mm2
Terminal screw torque - power
0.5Nm
1.0Nm
Terminal screw torque - alarm
-
0.5Nm
Environmental
IP 20
Mounting
TS35 DIN rail
Enclosure / colour
Metal / Black
Weight
200g
315g
335g
315g
335g
395g
415g
Dimensions
Width
Standards Compliance
IEC 61643-11 class II, III
14
18mm
Height
Options [*]
IEEE C62.41 categories C, B, A
External alarm contacts
IEC 1000-4-5
Polycarbonate enclosure
UL1449 fourth edition
Voltage variation
72mm
95mm
Depth
AS/NZS 1768 categories C, B, A
54mm
80mm
70mm
-
A
P
UC
30V/65V/130V
65V/130V
POWER PROTECTION - Series Surge Protectors
SSP Surge Protectors - Three Phase
Novaris SSP protectors are suitable for installation in circuits up to 63A. The
SSP range has been engineered to provide excellent performance and
installation independent let-through voltage. Their compact design makes
them an ideal choice for space restricted applications.
SSP 3 - 63 - 100 - 275 - [*]
SSP3-63-100-275-A
SSP3-63-50-275-A
SSP3-32-100-275-A
SSP3-32-50-275-A
SSP3-20-100-275-A
SSP3-20-50-275-A
SSP3-10-10-275-A
Product Series Options PhaseUc
IL Imax
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Phases
3
Nominal voltage
U0
230V / 50Hz
Maximum continuous voltage
Uc
275V / 50Hz
IL
10A
Imax
10kA
50kA
100kA
Nominal discharge current (15 x 8/20μs)
In
5kA
20kA
40kA
Voltage protection level @ 3kA (8/20µs)
UP
<800V
Response time
tA
<5ns
Maximum load current
Maximum discharge current (8/20µs)
20A
32A
Earth leakage current
63A
50kA
100kA
50kA
100kA
20kA
40kA
20kA
40kA
<10µA
Display
LED status
Alarms
Passive NC
Segment / thermal failure, clean SPDT contact
Alarm isolation to active circuitry
4kV
Maximum backup fuse (gG)
10A
20A
32A
63A
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Connection type
Screw terminal
Terminal capacity - power
2.5mm2
16mm2
Terminal capacity - alarm
2.5mm
2.5mm2
Terminal screw torque - power
0.5Nm
1.0Nm
Terminal screw torque - alarm
0.5Nm
2
0.5Nm
Environmental
IP 20
Mounting
TS35 DIN rail
Enclosure / colour
Metal / Black
Weight
200g
690g
750g
690g
750g
690g
750g
Dimensions
Standards Compliance
IEC 61643-11 class II, III
Width
54mm
Height
118mm
Depth
AS/NZS 1768 categories C, B, A
Options [*]
IEEE C62.41 categories C, B, A
External alarm contacts
IEC 1000-4-5
Polycarbonate enclosure
UL1449 fourth edition
Voltage variation
126mm
95mm
70mm
Standard
P
Uc
65/130/320
130V
15
POWER PROTECTION - Surge Filters
SFH Surge Filters 250 – 800A
Novaris SFH surge filters provide the highest level of protection with the
lowest let through voltage. When installed at a main switchboard Novaris
surge filters will protect all connected equipment.
SFH 3 - 250 - 200 - 275 - [*]
SFH3-800-200-275
SFH3-630-200-275
SFH3-400-200-275
SFH3-250-200-275
Product Series Options
Phase Uc
ILImax
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Nominal voltage
U0
230V / 50Hz
Maximum continuous voltage
Uc
275V / 50Hz
Phases
Discharge current 8/20µs
3
Imax
200kA
200kA
200kA
Nominal discharge current (15 x 8/20μs)
In
80kA
80kA
80kA
80kA
Maximum load current
IL
250A
400A
630A
800A
Protection stages
Metal oxide varistor / LC filter / metal oxide varistor
Voltage protection @ 3kA (8/20µs)
UP
<360V
Response time
tA
Instantaneous
Earth leakage current
Maximum voltage drop (% of U0)
3dB Frequency @ 50W
<10µA
DU
<1%
200Hz
150Hz
Displays
7-segment LED, percentage active
Alarms
Segment / thermal failure, clean SPDT contact
Alarm isolation to active circuitry
Mechanical Specifications
IEC 61643-11 class I, II, III
Operating temperature / humidity
AS/NZS 1768 category C, B, A
Connection type
IEEE C62.41 category C, B, A
Alarm terminal capacity
2.5mm2
IEC 1000-4-5
Terminal screw torque
0.5Nm
UL1449 fourth edition
Environmental
-40 to +70ºC / 5 to 95% non-condensing
Bus bar / cable lug
IP 55 in enclosure
Mounting
Weight
80Hz
4kV
Standards Compliance
Options [*]
200kA
Wall mount
90kg
160kg
HRC fusing
H
Metal enclosure IP 55
M
Over / under voltage relay
O
Width
710mm
800mm
Extended voltage (95-415V)
X
Height
710mm
1200mm
Spark Gap Frontend
G
Depth
285mm
400mm
16
Dimensions (in enclosure)
POWER PROTECTION - Surge Filters
SFH Surge Filters 1200 – 2000A
Novaris SFH surge filters provide the highest level of protection with the
lowest let through voltage. When installed at a main switchboard Novaris
surge filters will protect all connected equipment.
SFH 3 - 1200 - 200 - 275 - [*]
SFH3-2000-200-275
SFH3-1600-200-275
SFH3-1200-200-275
Product Series Options
Phase Uc
ILImax
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Nominal voltage
U0
230V / 50Hz
Maximum continuous voltage
Uc
275V / 50Hz
Phases
Discharge current 8/20µs
3
Imax
200kA
200kA
Nominal discharge current (15 x 8/20μs)
In
80kA
80kA
80kA
Maximum load current
IL
1200A
1600A
2000A
Protection stages
Metal oxide varistor / LC filter / metal oxide varistor
Voltage protection @ 3kA (8/20µs)
UP
<360V
Response time
tA
Instantaneous
Earth leakage current
Maximum voltage drop (% of U0)
3dB Frequency @ 50W
<10µA
DU
<1%
80Hz
Displays
7-segment LED, percentage active
Alarms
Segment / thermal failure, clean SPDT contact
Alarm isolation to active circuitry
Standards Compliance
200kA
4kV
Mechanical Specifications
IEC 61643-11 class I, II, III
Operating temperature / humidity
AS/NZS 1768 category C, B, A
Connection type
IEEE C62.41 category C, B, A
IEC 1000-4-5
UL1449 fourth edition
Bus bar / cable lug
Alarm terminal capacity
2.5mm2
Terminal screw torque
0.5Nm
Environmental
Mounting
Options [*]
-40 to +70ºC / 5 to 95% non-condensing
Weight
IP 55 in enclosure
Wall mount
120kg
HRC fusing
H
Metal enclosure IP 55
M
Dimensions (in enclosure)
Over / under voltage relay
O
Width
700mm
Extended voltage (95-415V)
X
Height
1300mm
Spark Gap Frontend
G
Depth
340mm
17
POWER PROTECTION - Surge Filters
SFM Surge Filters 40 – 63A
Novaris SFM surge filters provide excellent and effective MSB and DB
protection for critical equipment up to 63A per phase.
SFM 1 - 40 - 50 - 275 - [*]
SFM3-63-200-275
SFM3-63-50-275
SFM1-63-200-275
SFM1-63-50-275
SFM3-40-200-275
SFM3-40-50-275
SFM1-40-50-275
SFM1-40-200-275
Product Series Options
Phase Uc
ILImax
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Nominal Voltage
U0
Maximum continuous voltage
Uc
230V / 50Hz (110V / 60Hz by request only)
275V / 50Hz (130V / 60Hz by request only)
Phases
1
3
Discharge current 8/20µs
Imax
50kA
200kA
Nominal discharge current (15 x 8/20μs)
In
20kA
80kA
Maximum load current
IL
1
200kA
50kA
200kA
20kA
80kA
20kA
80kA
40A
200kA
20kA
80kA
LED status
% active
Metal oxide varistor / LC filter / metal oxide varistor
Voltage protection @ 3kA (8/20µs)
UP
<360V
Response time
tA
Instantaneous
Earth leakage current
<1µA
DU
<1%
3dB Frequency @ 50W
Displays
50kA
63A
Protection stages
Maximum voltage drop (% of U0)
3
50kA
750Hz
LED status
% active
Alarms
420Hz
LED status
% active
LED status
% active
Segment failure and overcurrent / thermal overload, SPDT contact
Alarm isolation to active circuitry
4kV
Mechanical Specifications
Standards Compliance
Operating temperature / humidity
IEC 61643-11 class I, II, III
Connection type
AS/NZS 1768 categories C, B, A
Terminal capacity - power
35mm2
IEEE C62.41 categories C, B, A
Terminal capacity - alarm
2.5mm2
IEC 1000-4-5
Terminal screw torque - power
1.0Nm
UL1449 fourth edition
Terminal screw torque - alarm
0.5Nm
18
UIK35 Terminals
Environmental
Options [*]
Circuit breaker
-40 to +70ºC / 5 to 95% non-condensing
C
IP 55 in enclosure
Mounting
Weight (in enclosure)
Wall mount
9kg
10kg
18kg
22kg
10kg
11kg
20kg
24kg
HRC fusing
H
Metal enclosure IP 55
M
Dimensions (in enclosure)
Over / under voltage relay
O
Width
310mm
426mm
310mm
426mm
Extended voltage (95-415V)
X
Height
390mm
506mm
390mm
506mm
Spark Gap Frontend
G
Depth
130mm
200mm
130mm
200mm
POWER PROTECTION - Surge Filters
SFM Surge Filters 125A
Novaris SFM surge filters provide excellent and effective MSB and DB
protection for critical equipment up to 125A per phase.
SFM 1 - 125 - 50 - 275 - [*]
SFM3-125-200-275
SFM3-125-50-275
SFM1-125-50-275
SFM1-125-200-275
Product Series Options
Phase Uc
ILImax
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Nominal Voltage
U0
230V / 50Hz (110V / 60Hz by request only)
Maximum continuous voltage
Uc
275V / 50Hz (130V / 60Hz by request only)
Phases
1
3
Imax
50kA
200kA
Nominal discharge current (15 x 8/20μs)
In
20kA
80kA
Maximum load current
IL
Discharge current 8/20µs
Protection stages
50kA
200kA
20kA
80kA
125A
Metal oxide varistor / LC filter / metal oxide varistor
Voltage protection @ 3kA (8/20µs)
UP
<360V
Response time
tA
Instantaneous
Earth leakage current
Maximum voltage drop (% of U0)
<1µA
DU
<1%
3dB Frequency @ 50W
350Hz
Displays
LED status
% active
Alarms
Seg failure and o’current / thermal o’load, SPDT contact
Alarm isolation to active circuitry
LED status
% active
4kV
Mechanical Specifications
Operating temperature / humidity
Standards Compliance
-40 to +70ºC / 5 to 95% non-condensing
Connection type
IEC 61643-11 class I, II, III
AS/NZS 1768 categories C, B, A
IEEE C62.41 categories C, B, A
IEC 1000-4-5
UL1449 fourth edition
UIK35 Terminals
Terminal capacity - power
35mm2
Terminal capacity - alarm
2.5mm2
Terminal screw torque - power
1.0Nm
Terminal screw torque - alarm
0.5Nm
Environmental
IP 55 in enclosure
Mounting
Options [*]
Weight (in enclosure)
Wall mount
11kg
12kg
25kg
28kg
HRC fusing
H
Metal enclosure
M
Dimensions (in enclosure)
Over / under voltage relay
O
Width
310mm
426mm
Extended voltage (95-415V)
X
Height
390mm
506mm
Spark Gap Frontend
G
Depth
130mm
200mm
19
POWER PROTECTION - Surge Filters
SFD Surge Filters - Single Phase
Novaris SFD surge filters provide the highest level of protection for critical and
essential equipment up to 32A per phase. Their compact design makes them an
ideal choice for space restricted applications.
SFD 1 - 32 - 100 - 275 - [*]
SFD1-32-50-275
SFD1-32-100-275
SFD1-20-100-275
100kA
50kA
100kA
40kA
20kA
40kA
SFD1-20-50-275
SFD1-10-50-275-A
SFD1-10-50-275
SFD1-6-10-275
SFD1-2-10-275
Product Series Options PhaseUc
IL Imax
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Phases
1
Nominal voltage
U0
230V / 50Hz
Maximum continuous voltage
Uc
275V / 50Hz
Maximum load current
Maximum discharge current (8/20µs) (L-N)
Nominal discharge current (15 x 8/20μs)
IL
2A
6A
Imax
10kA
In
5kA
32A
Metal oxide varistor / LC filter / metal oxide varistor
Voltage protection level @ 3kA (8/20µs)
UP
Response time
tA
Earth leakage current
Display
20A
50kA
20kA
Protection stages
Maximum voltage drop (% of U0)
10A
50kA
<700V
<600V
Instantaneous
<500µA
<10µA
ΔU
<1%
LED status optional
LED status
Alarms (optional)
-
Segment / thermal failure, clean SPDT contact
Alarm isolation to active circuitry
-
4kV
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Connection type
Terminal capacity - power
Screw terminal
2.5mm
16mm2
2
Terminal capacity - alarm
Terminal screw torque - power
2.5mm
2
0.5Nm
1.0Nm
Terminal screw torque - alarm
0.5Nm
Environmental
IP 20
Mounting
TS35 DIN rail
Enclosure / colour
Weight
Metal / Black
200g
440g
600g
605g
625g
Width
18mm
54mm
Height
116mm
95mm
Depth
70mm
70mm
730g
Dimensions
Standards Compliance
IEC 61643-11 class II, III
AS/NZS 1768 categories A, B
IEEE C62.41 categories A, B
Options [*]
IEC 1000-4-5
LED indication and external alarm
UL1449 fourth edition
Polycarbonate enclosure
20
72mm
L (LED only)
108mm
A
P
750g
POWER PROTECTION - Surge Filters
SFD Surge Filters - Three Phase
Novaris SFD surge filters provide the highest level of protection for critical and
essential equipment up to 32A per phase. Their compact design makes them an
ideal choice for space restricted applications.
SFD 3 - 20 - 50 - 275 - [*]
SFD3-32-50-275-A
SFD3-10-50-275-A
SFD3-20-50-275-A
Product Series Options PhaseUc
IL Imax
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Phases
3
Nominal voltage
U0
Maximum continuous voltage
Uc
Maximum load current
IL
Maximum discharge current (8/20µs) (L-N)
Nominal discharge current (15 x 8/20μs)
230V / 50Hz
275V / 50Hz
10A
Imax
50kA
In
20kA
Protection stages
32A
Metal oxide varistor / LC filter / metal oxide varistor
Voltage protection level @ 3kA (8/20µs)
UP
Response time
tA
<600V
<650V
Instantaneous
Earth leakage current
Maximum voltage drop (% of U0)
20A
<10µA
ΔU
<1%
Display
LED status
Alarms (optional)
Segment / thermal failure, clean SPDT contact
Alarm isolation to active circuitr
4kV
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Connection type
Screw terminal
Terminal capacity - power
16mm2
Terminal capacity - alarm
2.5mm2
Terminal screw torque - power
1.0Nm
Terminal screw torque - alarm
0.5Nm
Environmental
IP 20
Mounting
TS35 DIN rail
Enclosure / colour
Weight
Metal / Black
1.2kg
1.5kg
1.7kg
Dimensions
Standards Compliance
IEC 61643-11 class II, III
AS/NZS 1768 categories A, B
Width
180mm
Height
95mm
Depth
70mm
IEEE C62.41 categories A, B
Options
IEC 1000-4-5
External alarm
UL1449 fourth edition
Polycarbonate enclosure
Standard
P
21
POWER PROTECTION - Surge Filters
Plug-in Surge Filters
Novaris plug-in surge filters plug into a standard mains outlet socket to
provide premium protection for sensetive or critical electronic equipment
PP 10 A 2 - 50
PP10A8-50
PP10A6-50
Imax
Outlets
PP10A4-50
PP10A2-50
Product Series IL Country Option
Electrical Specifications
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Nominal voltage
U0
230V / 50Hz
Maximum continuous voltage
Uc
275V / 50Hz
Maximum discharge current (8/20µs)
Imax
50kA
Nominal discharge current (15 x 8/20μs)
In
20kA
Maximum load current
IL
10A
Protection stages
Metal oxide varistor / LC filter / Metal oxide varistor
Voltage protection level @3kA (8/20µs)
UP
<600V
Response time
tA
Instantaneous
Power Consumption (@230V 50Hz)
<1W
Attenuation
-3dB at 900Hz, -60dB at 100kHz
Earth leakage current
Maximum voltage drop (% of U0)
<500µA
ΔU
<1%
Display
LED power and status
Mechanical Specifications
-40 to +70ºC / 0 to 90% non-condensing
Connection type - line side cord
IEC C14 Inlet
Standards Compliance
Connection type - load side outlet
IEC 61643-11 class II, III
Number of outlets
AS/NZS 1768 categories A, B
Environmental
IEEE C62.41 categories A, B
Mounting
IEC 1000-4-5
Weight
10A Australian (type I) outlet
2
4
6
8
IP 20
Free standing, (optional wall mount -M)
1.3kg
Dimensions
Country Option
22
Operating temperature / humidity
Australian - AS-3112
A
Width
European - CEE7/4
E
Height
155mm
205mm
140mm
255mm
British - BS-1363
B
Depth
60mm
305mm
POWER PROTECTION - Surge Filters
PP Plug-in Surge Filters 15A and Rack Mount
Novaris plug-in surge filters plug into Australian 15A outlet sockets and
provide premium protection for sensitive electronic equipment.
PP 15 A 1 - 19 - [*]
PP10I8-19 1RU
PP15A1-50
PP10A8-19 1RU
Options
Imax
Outlets
PP15A1-19
Product Series IL Plug type
Electrical Specifications
Connection type
Series
Modes of protection
Nominal voltage
All mode (L-N, L-PE, N-PE)
230V / 50Hz
U0
275V / 50Hz
Maximum continuous voltage
Uc
Maximum discharge current (8/20µs)
Imax
19kA
50kA
19kA
Nominal discharge current (15 x 8/20μs)
In
8kA
20kA
8kA
Maximum load current
IL
Protection stages
15A
10A
Metal oxide varistor / LC filter / metal oxide varistor
Voltage protection level @ 3kA (8/20µs)
UP
<600V
Response time
tA
Instantaneous
Earth leakage current
Maximum voltage drop (% of U0)
Display
<500µA
DU
<1%
LED power and status
LED Status
Mechanical Specifications
Operating temperature / humidity
Connection type - line side cord
-40 to +70ºC / 5 to 95% non-condensing
Australian plug
Connection type - load side outlet
Number of outlets
IEC 61643-11 class III, III
AS/NZS 1768 category A, B
IEEE C62.41 category A, B
8
IP 20
Free standing
Rack Mount
1.3kg
2.8kg
Width
170mm
484mm
Height
100mm
44mm
Depth
60mm
220mm
Weight
Standards Compliance
IEC Female
1
Environmental
Mounting
IEC Male / Country Lead
Australian socket
Dimensions
IEC 1000-4-5
Options [*]
UL1449 fourth edition
Wall mount brackets
M
23
24
Selecting Process Control Protection
Process control protection must:
1. Provide adequate protection for all equipment.
2. Achieve a long working life.
3. Allow the signal to pass under normal operation.
4. Optimise the cost and size of the surge protection devices (SPDs).
Options for Surge Protection Devices
Two port SPDs are connected in series with the line. Almost all Novaris process control SPDs incorporate
Z
this configuration where a low let through voltage, (Up) is always required to adequately protect low level
U
signals.
Z
Novaris process control SPDs contain a combination of voltage switching components comprising gas
discharge tubes, series impedances and voltage limiting components comprising MOVs and suppressor
diodes.
Selection of Surge Protection Devices
The selection of SPDs for process control requires more attention than the selection of power line SPDs
to ensure the signal is not attenuated or lost through the SPD. Novaris manufactures process control
SPDs for almost all applications and can design custom solutions for unique applications.
1. Determine the signalling protocol and peak line voltage
Table 1 on page 58 provides common signalling protocols and the appropriate Novaris SPD for each
application. Even if the actual protocol is unknown the peak signal voltage must be determined.
2. Select the clamping voltage
The clamping voltage of the SPD must be greater than the peak signalling voltage.
The following is a guide.
Nominal Peak Signal Voltage (V)
Power System (V)
Clamping Voltage (V)
0-6
6
7v5
6-15
12
18
15-30
24
36
30-60
48
68
3. Determine the signal current
Standard SL models are rated at IL = 250mA. For current up to IL = 6A use the SSP6A series.
For higher current applications, consider using SFD surge filters.
4. Select signal frequency / data rate
Standard SL series will pass signals up to 250kHz. For higher frequency / faster data rates consider the
SL485 or SL-DH.
5. Consider earth isolation
The normal SL DIN rail base, designated -G, connects the protective earth to the DIN rail to provide a
low impedance earth path. If the earth must be isolated, for example with instrument loops, use the -EC90
base.
25
PROCESS CONTROL PROTECTION
SL Slimline Signal Line Protectors
Novaris SL range of plug-in signal line protectors provide surge protection for
most twisted pair signalling schemes. Ideal for the protection of PLCs, fire
and security systems, telecommunications and telemetry systems, railway
signalling, SCADA and other industrial monitoring and control equipment.
SL 7v5 - [*]
SL-PSTN
SL-iSwitch
65V
200V
200V
46V
140V
140V
SL68
SL36
Base option
SL18
SL7v5
Product Series Top
Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common mode
Uc
7V
16V
34V
Maximum continuous voltage (AC)
Uc
5V
11V
24V
Discharge current 8/20µs
Imax
Maximum continuous voltage (DC)
Maximum load current
IL
Impulse voltage 1.2/50µs
Up
10kA
250mA
8V
19V
40V
Impulse durability
76V
235V
30V
8.2W
17W
C2 8/20µs, 5kA, 10 times
1 Arms, 1s, 5 times
AC durability
Overstessed fault mode
Line resistance
180mA
Mode 3 (open circuit)
9W
Insertion loss @ 150W
0.5dB
3dB Frequency @ 50W
250kHz
0.4dB
10MHz
Mechanical Specifications
Operating temperature / humidity
Terminal capacity
2.5mm2
Terminal screw torque
0.5Nm
Environmental
Mounting
Weight
Standards Compliance
ITU-T K.44
AS/NZS 1768
IEEE C62.41
35g
Width
7mm
Height
102mm
Depth
68mm
Base Options [*]
UL497B
Earth connected to DIN rail
Earth connected to DIN rail via GDT
IECEx ia models available with the Novaris Hazardous Area range
Refer to page 58 for signalling protocol compatibility
26
IP 20
TS35 DIN rail
Dimensions
IEC 61643-21
A-tick (PSTN & iSwitch)
-40 to +70ºC / 5 to 95% non-condensing @ min current
G
EC90
20MHz
PROCESS CONTROL PROTECTION
SL Slimline Signal Line Protectors
Novaris SL range of plug-in signal line protectors provide surge protection for
most twisted pair signalling schemes. Ideal for the protection of PLCs, fire
and security systems, telecommunications and telemetry systems, railway
signalling, SCADA and other industrial monitoring and control equipment.
SL 485 - [*]
SL-420
SL-RTD
Base option
SL-DH
SL485-EC90
Product Series Top
Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common mode
Uc
8V
34V
Maximum continuous voltage (AC)
Uc
6V
24V
Discharge current 8/20µs
Imax
Maximum continuous voltage (DC)
Maximum load current
IL
Impulse voltage 1.2/50µs
Up
8V
34V
6V
-
10kA
250mA
15V
Impulse durability
30mA
50V
15V
40V
C2 8/20µs, 5kA, 10 times
1 Arms, 1s, 5 times
AC durability
-
Overstressed fault mode
Mode 3 (open circuit)
Line resistance
3.9W
8.2W
Insertion loss @ 150W
0.2dB
1.5dB
3dB Frequency @ 50W
70MHz
250kHz
-
LED Status
Display
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing @ min current
Terminal capacity
2.5mm2
Terminal screw torque
0.5Nm
Environmental
IP 20
Mounting
TS35 DIN rail
Weight
35g
Dimensions
Standards Compliance
ITU-T K.44
AS/NZS 1768
Width
7mm
Height
102mm
Depth
68mm
IEEE C62.41
Base Options [*]
IEC 61643-21
Earth connected to DIN rail
UL497B
Earth connected to DIN rail via GDT
-
G
Standard
EC90
IECEx ia and ATEX models available with the Novaris Hazardous Area range
Refer to page 58 for signalling protocol compatibility
27
PROCESS CONTROL PROTECTION
SSP Slimline Series Surge Protectors
Novaris SL range of plug-in signal line protectors provide surge protection for
power supplies with loads up to 6A. Ideal for the protection of PLCs, fire
and security systems, telecommunications and telemetry systems, railway
signalling, SCADA and other industrial monitoring and control equipment.
SSP 6A - 14 - G
SSP6A-130
SSP6A-65
SSP6A-38
Base options
Uc
SSP6A-26
SSP6A-14
Product Series IL
Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common mode
Maximum continuous voltage (DC)
Uc
14V
26V
38V
65V
170V
Maximum continuous voltage (AC)
Uc
11V
20V
30V
50V
130V
Maximum discharge current (8/20µs)
Imax
Maximum load current
IL
Voltage protection level @ 5kV (10/700µs)
Up
9.6kA
3.6kA
6A
26V
52V
Line resistance
70V
120V
0.1W
3dB Frequency @ 50W
100kHz
Mechanical Specifications
Operating temperature / humidity
-40 to +70ºC / 5 to 95% non-condensing
Terminal capacity
2.5mm2
Terminal screw torque
0.5 Nm
Environmental
Mounting
Weight
IP 20
TS35 DIN rail
35g
Dimensions
Standards Compliance
ITU-T K.44
AS/NZS 1768
Width
7mm
Height
102mm
Depth
68mm
IEEE C62.41
Base Options
IEC 61643-21
Earth connected to DIN rail
UL497B
Earth connected to DIN rail via GDT
IECEx ia and ATEX models available with the Novaris Hazardous Area range
Refer to page 58 for signalling protocol compatibility
28
G
EC90
250V
PROCESS CONTROL PROTECTION
SLT Threaded Signal Line Protectors
Novaris Threaded Signal Line Protectors provide a means of protecting the
signalling lines of field equipment. They are suitable for two, three and
four wire instruments. SLT models are available for signalling systems up
to 200V.
SLT 1 - [SIG] - [THREAD]
SLT4
SLT3
Thread
Voltage Options
SLT1
Product Series 1 Pair / 3 / 4 Wire
Electrical Specifications
Connection type
Shunt
Modes of protection
Transverse and common
Number Signal Wires
Maximum discharge current (8/20µs)
2
3
4
10kA
Imax
3dB Frequency @ 50W
250kHz
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95%
Environmental
IP 67 (Installed)
Enclosure
Stainless Steel
18
36
68
200
36-275
165g
7V5
Weight (packed)
Maximum continuous voltage DC
Uc
7V
16V
36V
65V
200V
36V (sig)
Maximum continuous voltage AC
Uc
5V
11V
24V
46V
140V
275V (pwr)
Voltage protection level @ 5kV (10/700µs)
Up
45V
50V
80V
120V
400V
80V / 600V
Signal Levels [SIG]
M20
N12
Standards Compliance
ITU-T K.44
Thread Type [THREAD]
AS/NZS 1768
Width
27mm
24mm
IEEE C62.41
Height
31mm
UL497B
Depth
IEC61643-21
27mm
53mm
IECEx ia, IECEx d (M20), and ATEX models available with the Novaris Hazardous Area range
Refer to page 58 for signalling protocol compatibility
29
PROCESS CONTROL PROTECTION
Accessories
SL Test Plug
SL-TEST
Novaris SL Test Plug provides access to field and equipment terminals plus earth via mini banana
sockets mounted in the top face of the test plug. It provides a convenient way to connect to these
lines for testing.
SL Earth Comb
SL-COMB
The Novaris SL Earth Comb provides a convenient means of connecting the common points of SL series
surge protectors. The earth comb contains nine contacts, allowing banks of 8 SL protectors to be
commoned together with one overlapping contact. The earth comb can be cut to provide a lesser
number of points. The earth comb contains two 6.3mm spade terminals.
Novaris Screwdriver
SL-SCREW
30
PROCESS CONTROL PROTECTION
SLM Multiline Protectors
Novaris SLM offers protection for up to 12 signal lines. Typical applications
include process control, telemetry, PLC, and irrigation systems.
SLM - 7v5 - [*]
SLM-200
SLM-68
SLM-36
Options SLM-18
SLM-7v5
Product Series Uc
Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common mode
Number of lines
12
Maximum continuous voltage (DC)
Uc
7V
16V
34V
65V
200V
Maximum continuous voltage (AC)
Uc
5V
11V
24V
46V
140V
Discharge current 8/20µs
Imax
20kA
Protection stages
Multistage
Maximum load current
IL
Impulse voltage 10/700µs
Up
350mA (2A for option 2; 500mA for option H)
8V
19V
40V
Line resistance - base
8.2W
Line resistance - 2A
0.1W
Line resistance - high frequency
Maximum frequency
76V
235V
3.9W
fc
250kHz (25MHz high frequency option)
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95% non-condensing
Terminal capacity
2.5mm2
Terminal screw torque
0.5Nm
Environmental
IP 20
Mounting
Panel mount
Weight
250g
Dimensions
Standards Compliance
IEC61643-21
ITU-T K.44
Width
128mm
Height
80mm
Depth
42mm
AS/NZS 1768
Options [*]
IEEE C62.41
Maximum load current 2A
IL
2
UL497B
High frequency 25MHz
fc
H
31
PROCESS CONTROL PROTECTION
RS Serial Port Protectors
Novaris RS Protectors provide protection for serial protocol systems in
RS232 and RS485 applications. These units are housed in a headshell
enclosure.
DB 9 - RS232
DB9-RS485
DB9-RS232
DB25-RS485
Signalling Protocol
DB25-RS232
Product Series Connector
Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common
Maximum continuous voltage
Uc
Discharge current 8/20µs
Imax
36V
8.2V
250A
Protection stages
SAD and GDT
Number of lines
8
Impulse voltage 10/700µs
Up
Signalling protocol
40V
14V
RS232
RS485
Mechanical Specifications
Operating temperature / humidity
Connection type
Standards Compliance
IEC61643-21
DB9
DB25
Connector orientation
M/F
Environmental
IP 20
Weight
70g
ITU-T K.44
Dimensions
AS/NZS 1768
Width
IEEE C62.41
Height
17mm
UL497B
Depth
63mm
Refer to page 58 for signalling protocol compatibility
32
-40 to +85ºC / 5 to 95% non-condensing
34mm
56mm
DB9
DB25
34mm
56mm
PROCESS CONTROL PROTECTION
LCP Load Cell Protector
The Novaris LCP provides protection for both 4-wire and 6-wire loadcells
as well as the measuring instrument. The LCP is contained within an
IP65 enclosure, or alternatively as a PCB only. Installation of the LCP is
certified and does not affect weighbridge calibration.
LCP - 36 - [*]
LCP-36-PCB
LCP-18-PCB
LCP-36
LCP-18
Product Series Option
Uc
Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common mode
Maximum continuous voltage (DC)
Uc
Maximum discharge current (8/20µs)
Imax
18V
36V
<40
<70
SAD and GDT
UP
<40
<70
Impulse durabiltiy
C1 8/20µs, 0.25kA, 300 times
Over stressed fault mode
Maximum load current
36V
250A
Protection stages
Voltage protection level @ 0.25kA (8/20µs)
18V
Mode 2
IL
6.5A
Lines protected
5A
4 or 6
Mechanical Specifications
Operating temperature / humidity
Terminal capacity
2.5mm2
Terminal screw torque
0.5Nm
Ground connection
Environmental
Standards Compliance
IEC61643-21
ITU-T K.44
-40 to +85ºC / 5 to 95% non-condensing
M5 s/s stud
Mounting
Enclosure / colour
Weight
100mm lead
IP 65
IP 00
Panel mount
Aluminium / black
PCB only
600g
80g
76mm
AS/NZS 1768
Dimensions
IEEE C62.41
Width
116mm
UL497B
Height
65mm
63mm
NSC No: S366
Depth
56mm
20mm
IECEx ia and ATEX models available with the Novaris Hazardous Area range
Refer to page 58 for signalling protocol compatibility
33
SURGE PROTECTION TESTER
Surge Protection Tester
The Novaris SPT Series allows surge protection installers and maintainers to monitor*
and diagnose surge protection equipment on site. The SPT-02 uses an autorange function to accurately determine the clamping voltage of voltage limiting
products and the firing voltage of voltage switching products. The SPT-02 is also
a multifuction device that supports insulation resistance, continuity, voltage and
diode testing. Test results are displayed on a 2 x 16 character display.
SPT - 02
Product Series
MOV Test
Continuity
Measuring Range
5 -- 1020 V DC
Voltage Accuracy
± 3%
GDT Test
Measuring Range
5 -- 1020 V DC
Voltage Accuracy
± 3%
Voltmeter
Ranges
0.01 -- 100Ω
100 -- 300Ω
300 -- 1999Ω
Accuracy
0.01 -- 100Ω : ± 1.0%
100 -- 300Ω : ± 1.5%
300 -- 1999Ω : ± 2.0%
Auto Null
up to 5Ω
Buzzer
up to 3Ω
DC Voltage
0 -- 950 V
Diode Test
AC Voltage
0 -- 700V
Test Voltage
5V DC
Resolution
1V
Max Test Current
1.5 mA
Voltage Accuracy
± 3%
Insulation Resistance
Test voltage
Resolution
Measurement Voltage
250, 500, 1000V
Accuracy
Measuring Ranges
250V: 0.2MΩ -- 2GΩ
500V: 0.2MΩ -- 4GΩ
1000V: 0.2MΩ -- 8GΩ
General
Accuracy
0.2MΩ - 4GΩ : ± 3%
4GΩ -- 8GΩ : ± 5%
Display
Short Circuit Current
Polarisation Index (PI)
Detective Absorbtion Ratio (DAR)
1.2mA
Ranges
Short Circuit Test Current
Standards Compliance
EN 61010-1 CATIII 600V
EN 61326-1
Fuse
Dimensions
on all ranges
Weight
on all ranges
Power Source
Storage Temperature
KΩ Test
34
Version
Accessories
1 -- 400kΩ
≥ 1.3mA
0.1V
0 -- 4.5V
± 3%
500mA 250V Fast Blow
2 Line x 16 Character LCD
205 (L) x 90 (W) x 55 (D)
1.5kG
1.5V AA x 6
-20˚C to 70˚C
Test Leads
Fuse (0.5A 250V)
Heavy Duty Case
Instruction Manual
Batteries
* Measurements of SPDs with intact display hardware will be inaccurate
due to the current required to drive the hardware.
LAN & CCTV PROTECTION
CL Coaxial CCTV Protectors
Novaris Coaxial CCTV protectors are suited to the protection of security and
CCTV applications. The 68V version has been specifically designed for
PoE over coax applications.
CL B - M F - [*]
CLF-FF
CLB-FM
Voltage Options
Gender Line
CLB-FF
CLB-MF
Product Series Connector Gender EQPT
Electrical Specifications
Connection type
Series
Modes of protection
Maximum discharge current (8/20µs)
Maximum load current
Transverse and common modes
Imax
20kA
IL
500mA
Protection stages
Multistage
3dB frequency
100MHz
Insertion loss
<1dB @ 20MHz
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95% non-condensing
Connector type
BNC
Connector orientation (EQPT / line)
M/F
F-type
F/F
Environmental
F/M
F/F
IP 20
Enclosure / colour
Aluminium / Black
Weight
100g
Dimensions
Width
26mm
Height
26mm
Depth
89mm
86mm
86mm
88mm
Standards Compliance
10
18
36
68
ITU-T K.44
IEEE C62.41
Voltage Options [*]
IEC 61643-21
Maximum continuous voltage
Uc
8.2V
18V
36V
68V
Voltage protection level @ 5kV (10/700µs)
Up
14V
20V
40V
76V
AS/NZS 1768
UL497B
Refer to page 58 for signalling protocol compatibility
35
CCTV PROTECTION
SFD Combined Power and Signal Protectors
Novaris protection for both power and signal is provided in one compact and
economical DIN compliant package. Ideal for security and CCTV camera
protection.
SFD 1 - 2 - 3 - 30 - C
SFD1-6-10-275-C
SFD1-2-10-275-C
SFD1-6-10-130-C
SFD1-6-10-50-C
SFD1-2-10-130-C
CCTV
Uc
Imax
SFD1-2-10-50-C
SFD1-6-3-30-C
SFD1-2-3-30-C
Product Series Phase IL
Power Line Protection
Connection type
Series
Modes of protection
All mode (L-N, L-PE, N-PE)
Nominal voltage
U0
24V / 50Hz / 60Hz
40V / 50Hz / 60Hz
Maximum continuous voltage
Uc
30V / 50Hz / 60Hz
50V / 50Hz / 60Hz
Phases
Maximum discharge current (8/20µs)
Maximum load current
230V / 50Hz / 60Hz
130V / 50Hz / 60Hz
275V / 50Hz / 60Hz
1
3kA
Imax
IL
2A
10kA
6A
Protection stages
2A
6A
2A
6A
Up
Response time
tA
Earth leakage current
<100V
<180V
<450V
Instantaneous
<500uA
DU
<1%
Signal Line Protection
Connection type
Series
Modes of protection
Transverse and common modes
Maximum continuous voltage
Uc
8.2V
Maximum discharge current (8/20µs)
Imax
20kA
Maximum load current
IL
Protection stages
Impulse voltage 1.2/50µs
500mA
Gas discharge tube / series impedance / SAD
Up
14V
3dB frequency
200MHz
Insertion loss
<1dB @ 20MHz
Mechanical Specifications
Operating temperature / humidity
Standards Compliance
IEC 61643-11 class III
AS/NZS 1768 categories A
IEEE C62.41 categories A
IEC 1000-4-5
36
-40 to +85ºC / 5 to 95% non-condensing
Connector type - power
2.5mm2 polarised plugs
Connector type - signal
Female / female BNC
Terminal screw torque
0.5 Nm
Environmental
Mounting
Weight
2A
6A
Metal oxide varistor / LC filter / metal oxide varistor
Voltage protection level @ 3kA (8/20µs)
Maximum voltage drop (% of U0)
110V / 50Hz / 60Hz
IP 20
TS35 DIN rail
200g
UL1449 fourth edition
Dimensions
ITU-T K.44
Width
18mm
IEC 61643-21
Height
116mm
UL497B
Depth
70mm
<750V
LAN PROTECTION
RJ45 Network Protectors - Terminal
Novaris RJ45 terminal protectors are compliant with 1000BaseT (gigabit
Ethernet), CAT6 and power over ethernet applications.
RJ45 - 1CAT6 - [*]
RJ45-24PoE
RJ45-16PoE
RJ45-8PoE
RJ45-1PoE
RJ45-24CAT6
RJ45-16CAT6
RJ45-8CAT6
RJ45-1CAT6
Product Series Options
Circuits
Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common modes
Lines protected
All
Maximum continuous voltage
Uc
6 VDC
6 VDC
Maximum PoE voltage
Uc
-
80 VDC
Maximum discharge current (8/20µs)
Imax
Maximum load current
10kA
600mA
IL
Protection stages
Voltage protection level @ 5kV (10/700µs)
Multistage
Multistage signal, single stage power
<20V
Up
Impulse durability
C2 8/20µs, 1.5kA, 10 times
Overstressed fault mode
Mode 3 (open circuit)
Insertion loss @ 150W
Maximum frequency
<0.1dB
250MHz
fc
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95% non-condensing
Connection type
Number of outlets
Standards Compliance
Environmental
100BaseT
Mounting
1000BaseT
Enclosure / colour
CAT5
Weight
CAT5e
CAT6
TIA/EIA 568A
TIA/EIA 568B
AS/NZS 1768
RJ45 socket
1
8
16
24
1
8
16
24
IP 20
Inline
2RU rack mount
Inline
2RU rack mount
Aluminium / black
200g
1.85kg
1.95kg
2.0kg
200g
1.85kg
1.95kg
2.0kg
Dimensions
Width
26.5mm
483mm
26.5mm
483mm
Height
27.5mm
89mm
27.5mm
89mm
Depth
80mm
80mm
80mm
80mm
Included
-
Included
-
IEEE C62.41
Options [*]
IEC 61643-21
DIN rail mounting clip
Refer to page 58 for signalling protocol compatibility
37
38
Selecting Coaxial Protection
Coaxial line surge protection must:
1. Provide adequate protection for all equipment.
2. Achieve a long working life.
3. Allow the signal to pass under normal operation and not have an adverse affect on insertion loss
and return loss.
4. Optimise the cost and size of the surge protection devices (SPDs).
Options for Surge Protection Devices
Novaris manufacturers two types of RF coaxial SPDs. Those containing a gas discharge tube (GDT)
are suitable for a wide frequency range but must be chosen carefully taking into account the power
on the line if used for a transmitting application. Quarter wave stub protectors offer exceptionally low
let through voltages but are frequency sensitive. Their power handling capability is only limited by the
rating of the coaxial connectors employed.
Selection of Surge Protection Devices
1. Identify the connector type
Novaris manufactures a range of coaxial SPDs to suit most common connectors and gender variations.
2. Select the clamping voltage
The clamping voltage of the SPD must be greater than the peak voltage on the line. This is particularly
important when used for transmitting applications. The following is a guide.
Power in 50W (W)
GDT Voltage (V)
0-40
90
40-125
230
125-300
350
300-800
600
800-2000
1000
Please contact us for higher power levels
3. Identify the maximum operating frequency
3G models are available in all standard small format connector types and feature replaceable GDTs and
will operate to 3 GHz. 6G models are available in only N trype connectors and will operate to 6 GHz.
4. Tuned stub protectors
For narrow bandwidth applications where no DC voltage is injected, tuned stub protectors provide
exceptionally low let through voltages and very low intermodulation products. The centre operating
frequency must be specified when ordering.
39
COAXIAL PROTECTION
RF Equipment Protection up to 3GHz
Novaris gas discharge surge protectors are capable of passing RF signals to
3GHz (limited by connector type). N-type female / female protectors are
suitable for bulkhead mounting.
C N - FF - 90 - 3 - [*]
CN-FF-1000-3
CN-MF-1000-3
CN-FF-600-3
CN-MF-600-3
CN-FF-350-3
CN-MF-350-3
CN-FF-230-3
CN-MF-230-3
CN-FF-90-3
CN-MF-90-3
Product Series Options
Connector fc
GenderUc
Electrical Specifications
Connection type
Series
Modes of protection
Signal-Earth
Sparkover voltage
Uc
Maximum discharge current (8/20µs)
Imax
fc
Voltage protection level @ 5kV (10/700µs)
UP
230VDC
350VDC
0 - 40W
40 - 125W
125 - 300W
600VDC
1000VDC
300-800W
800-2000W
<1.3kV
<1.8kV
20kA
Power rating
Maximum working frequency
90VDC
3GHz
<650V
<820V
<1.1kV
Impulse durability
C2 8/20µs, 5kA, 10 times
Overstressed fault mode
Mode 3 (open circuit)
Characteristic impedance
50W (75W F-type only)
Capacitance (line-shield @1MHz)
<1pF
VSWR
<1.1:1
Return loss
>26dB
Insertion loss
<0.1dB
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95% non-condensing
Connection type
N-type
Connection orientation
M/F
F/F
M/F
F/F
Mounting
M/F
F/F
M/F
F/F
M/F
F/F
Inline / bulkhead (N-type only)
Environmental
IP 55
Enclosure / colour
Brass / Nickel Plated
Weight
150g
Connector type variation
Options [*]
BNC
M
7/16 DIN
DIN rail mounting clip
D
F-type
-
F
-
F
-
G rail mounting clip
G
N-type (bulkhead mount female)
N
Standard
N
Standard
N
Earth stud
E
UHF
U
SMA
S
Standards Compliance
40
B
90º mounting bracket
D (Mounting bracket not available)
ITU-T K.44
Dimensions
AS/NZS 1768
Configuration
IEEE C62.41
Width
25mm
IEC 61643-21
Height
25mm
UL497B
Maximum length
CB-MF
58mm
CB-FF
52mm
CD-MF
CD-FF
CF-FF
CN-MF
F
-
F
-
F
Standard
N
Standard
N
Standard
CN-FF
CU-MF
CU-FF
CT-MF
CT-FF
25mm
Ø40mm
70mm
73mm
25mm
50mm
60mm
60mm
57mm
54mm
COAXIAL PROTECTION
RF Equipment Protection up to 6GHz
Novaris gas discharge surge protectors are capable of passing RF signals to
6GHz (limited by connector type). N-type female / female protectors are
suitable for bulkhead mounting.
C N - FF - 90 - 6
CN-FF-230-6
CN-MF-230-6
fc
Uc
CN-FF-90-6
CN-MF-90-6
Product Series Connector Gender
Electrical Specifications
Connection type
Series
Modes of protection
Signal-Earth
Sparkover voltage
Uc
Maximum discharge current (8/20µs)
Imax
90VDC
230VDC
20kA
Power rating
0 - 40W
Maximum working frequency
fc
Voltage protection level @ 3kA (8/20µs)
UP
40 - 125W
6GHz
<650V
Impulse durability
<820V
C2 8/20µs, 5kA, 10 times
Overstressed fault mode
Mode 3 (open circuit)
Characteristic impedance
50W
VSWR
<1.1:1
Return loss
>26dB
Insertion loss
<0.2dB
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95% non-condensing
Connection type
Connection orientation
N-type
M/F
Mounting
Standards Compliance
ITU-T K.44
F/F
M/F
F/F
Inline / bulkhead
Maximum bulkhead thickness
9mm
Environmental
IP 55
Enclosure / colour
Brass / Nickel Plated
Weight
160g
AS/NZS 1768
Dimensions
IEEE C62.41
Width
26mm
IEC 61643-21
Height
26mm
UL497B
Maximum length
62mm
69mm
62mm
69mm
41
COAXIAL PROTECTION
RF Equipment Protection Tuned Stub
Novaris tuned stub surge protectors employ quarter-wavelength short circuit
stub technology. Suitable for narrow bandwidth applications where no DC
voltage is injected. RF power and surge rating are limited by the cables
and connectors only.
CSTUB - N - MF - 2400
CSTUB-N-FF-2400
CSTUB-N-MF-2400
CSTUB-D-FF-2400
CSTUB-N-FF-900
CSTUB-D-MF-2400
tf
Gender
CSTUB-N-MF-900
CSTUB-D-FF-900
CSTUB-D-MF-900
Product Series Connector Electrical Specifications
Connection type
Series
Modes of protection
Maximum discharge current (8/20µs)
Signal-Earth
50kA
Imax
Power rating
Limited only by connectors and cables used.
Tuned frequency range
tf
400MHz to 3GHz (specify)
Voltage protection level @ 3kA (8/20µs)
UP
<20V
Characteristic impedance
50W
Bandwidth
±10% of tuned frequency
VSWR
<1.1:1 within bandwidth
Return loss
>26dB within bandwidth
Insertion loss
<0.1dB at tuned bandwidth
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95% non-condensing
Connection type
Connection orientation
7/16 DIN
M/F
N-type
F/F
M/F
7/16 DIN
F/F
Inline
Maximum bulkhead thickness
9mm
Environmental
Standards Compliance
42
M/F
Mounting
Dimensions
AS/NZS 1768
Body diameter
IEEE C62.41
Height
IEC 61643-21
Maximum length
F/F
M/F
F/F
60mm
56mm
54mm
IP 55
Enclosure / colour
ITU-T K.44
N-type
Brass / silver
32mm
Depends upon operating frequency
63mm
60mm
56mm
54mm
63mm
COAXIAL PROTECTION
RF Equipment Protection High Power
Novaris high power surge protectors suit applications including MF, HF and
VHF transmitters to 50kW. The spark gap arrester has an optical arc
sensor which may be used to momentarily interrupt the transmitter.
CEIA - 078 - 1
CEIA-318
Options
CEIA-158
CEIA-078
Product Series Connector Size
Electrical Specifications
Connection type
Series
Modes of protection
Maximum discharge current (8/20µs)
Signal-Earth
100kA
Imax
Power rating
>50kW limited only by coaxial cable
Surge element
Spark gap, gap setting: 2mm / 10kW
Spark over voltage
2.6kV for 2mm gap
Characteristic impednce
50W
Overstressed fault mode
Mode 3 (open circuit)
Insertion loss
<0.1dB to 500MHz
<0.2db to 1GHz (gap setting: 1mm)
Return loss
>26dB to 500MHz
>20dB to 1GHz (gap setting: 1mm)
Arc sensor
Optical detector utilising photodiode, feeding transmitter interface
to provide momentary shutdown
Power requirements
Arc sensor: 12VDC @ 35mA
Transmission medium
Arc detector fed to transmitter via optic fibre.
Alternate metallic cable available.
Mechanical Specifications
Operating temperature / humidity
Connection type
Mounting
Standards Compliance
ITU-T K.44
Environmental
Enclosure
-40 to +85ºC / 5 to 95% non-condensing
7/8” EIA
1 5/8” EIA
3 1/8” EIA
Bulkhead / flange
IP 55
Brass and copper
AS/NZS 1768
Options
IEEE C62.41
Spark gap only, no TX controller
IEC 61643-21
1RU 19” rack, one TX controller only
1
UL497B
3RU 19” rack, up to 14 TX controllers
n*
Standard
* Denotes number of TX controllers
43
TELEPHONE PROTECTION
KP KRONE-LSA® MDF - 1 Pair / 10 Pair
The Novaris KP provides protection for KRONE-LSA® termination systems
and is suitable for all twisted pair telecommunication services. The unique
iSwitch technology offers the ultimate in protection against induced
transients and AC induction by totally isolating the load from the incoming
line during the disturbance.
KP 10 - [*]
KP10 -[*]
KP1-48-DC
KP1-24-DC
KP1-12-DC
Variant
KP1-06-DC
KP1-i
KP1-T
Product Series Pairs Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common modes
Uc
200VDC
8V
Maximum continuous voltageAC
Uc
140VAC
6V
Maximum discharge current (8/20µs)
Imax
Maximum continuous voltage DC
Maximum load current
IL
250mA
180mA
Up
<220V
<30V
56V
11V
22V
40V
* Refer to KP1-[*] version
specifications
250mA
Multistage
Impulse durability
<30V
<40V
<60V
<90V
C2 8/20µs, 5kA, 10 times
Overstressed fault mode
Series resistance
30V
10kA
Protection stages
Voltage protection level @ 1kV/µs
15V
Mode 3 (open circuit)
2.7W
17W
2.7W
Insertion loss @ 150W
0.4 dB
3dB Frequecny @ 150W
70Mhz
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95% non-condensing
Connection type
KRONE LSA-PLUS®
Environmental
Standards Compliance
Mounting
ITU-T K.44
Enclosure / colour
AS/NZS 1768
Weight
IEEE C62.41
Dimensions
IEC 61643-21
UL497B
A-tick
KRONE LSA-PLUS®
ABS / black
6.5g
150g
125mm
Width
9.4mm
Height
21mm
18mm
Depth
36mm
42mm
Note: KRONE-LSA® is a trademark of KRONE, GmbH, Germany
44
IP 20
TELEPHONE PROTECTION
RJ Modular Plug Protection
Novaris Modular Plug provides protection for twisted pair telecommunication
services suitable for telephones, FAX, dial-up, ISDN and DSL modems.
MPP - RJ12
MPP-RJ45
MPP-RJ12-i
MPPRJ12-Bi
Connector Type
MPP-RJ12-2
MPP-RJ12-1
Product Series Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common
Number of pairs
1
Maximum continuous voltage
Uc
Maximum discharge current (8/20µs)
Imax
Maximum load current
2
200VDC
10kA
IL
350mA
Up
<150V
Protection stages
Voltage protection level @ 5kV (10/700µs)
1
50kA
180mA
Multistage
Maximum frequency
<30V
20MHz
Series resistance
8.2W
17W
Mechanical Specifications
Standards Compliance
AS/NZS 4117
AS/ACIF S002
AS/NZS 60950
AS/NZS 1768
Operating temperature / humidity
Connection type
Environmental
Enclosure / colour
Weight (packed)
-40 to +85ºC / 5 to 95%
RJ12
RJ45
Aluminium / black
100g
IEEE C62.41
Dimensions (enclosure only)
IEC 61643-21
Width
26mm
UL497B
Height
26mm
Depth
90mm
A-tick
RJ12 / Screw terminal
IP 20
45
HIGH SURGE CURRENT SIGNAL LINE PROTECTORS
SLD - Hardwired
Novaris hardwired high energy multistage transient protection for highly
exposed circuits.
SLD 1 - [SIG] - [*]
SLD4
SLD2
Options
Signal Type
SLD1
Product Series Pairs
Electrical Specifications
Connection type
Series
Modes of protection
Transverse and common modes
Number of pairs
Maximum discharge current (8/20µs)
1
2
4
20kA
Imax
Protection stages
Multistage
Mechanical Specifications
Operating temperature / humidity
-40 to +85ºC / 5 to 95% non-condensing
2.5mm2 pluggable
Connection type
Environmental
IP 20
Mounting
TS35 DIN rail
Enclosure / colour
Metal / Black
Weight
250g
300g
400g
19.5mm
29mm
49mm
Dimensions
Width
Height
116mm
Depth
68mm
Options [*]
Maximum load current 2A
IL
2
DH
485
7v5
18
36
68
H
PSTN
High Frequency (5MHz for 250kHz units)
Standards Compliance
Maximum Continuous Voltage (DC)
Uc
200V
34V
8V
7V
18V
36V
68V
ITU-T K.44
Maximum Continuous Voltage (AC)
Uc
-
24V
6V
5V
11V
24V
46V
AS/NZS 1768
Impulse Voltage 1.2/50µs
Up
-
50V
15V
8V
19V
40V
76V
AS4117
Voltage Protection Level @ 1kV/µs
Up
<130V
IEC 61643-21
Maximum Load Current
IL
250mA
UL497B
Line Resistance
8.2W
3.9W
8.2W
3dB Frequency @ 50W
20MHz
10Mhz
250kHz
Signal Type [SIG] Electrical Specifications
A-tick
46
500mA
250mA
SPECIAL PRODUCTS
SIP Surge Indicator Panel
Novaris Surge Indicator Panel allows remote monitoring of any Novaris
product featuring external alarms. Visual and audible indicators provide
at-a-glance surge protection status. Designed to fit in standard 72mm
panel meter cutouts, integration into switchboards is simple.
SIP - 230
SIP-24
Nominal voltage
SIP-230
SIP-110
Product Series 230V / 50Hz
24V AC / DC
Electrical Specifications
Nominal voltage
U0
110V / 60Hz
Display
LED power and status
Alarm
SPDT contacts
Alarm isolation to active circuitry
4kV
Mechanical Specifications
Operating temperature / humidity
Connector type
Terminal screw torque
Environmental
Mounting
Panel cut-out
Weight
-40 to +70ºC / 5 to 95%
2.5mm2 polarised plug
0.5Nm
IP 20
Flush panel mount
68mm x 68mm
200g
Dimensions
Width
72mm
Height
72mm
Depth
55mm
47
SPECIAL PRODUCTS
EC Earth Clamp 20kA
Novaris EC provides a means to electrically clamp different earthing
systems during transient disturbances. Applications include computer
rooms and in the bonding of cable sheaths to ground where direct
bonding would introduce interference and “earth loops”.
EC 20 - 90
EC20-600
EC20-350
Uc
EC20-230
EC20-90
Product Series Imax
Electrical Specifications
Active element
DC spark over voltage
Gas Discharge Tube (GDT)
Uc
90V
230V
Voltage tolerance
350V
600V
<850V
<1200V
± 20%
Discharge current 8/20µs
Imax
Voltage protection level @ 5kV (10/700µs)
UP
20kA
<640V
<700V
Isolation resistance
>1010W
Capacitance
<0.8pF
Mechanical Specifications
Operating temperature / humidity
Connection type
Standards Compliance
48
-40 to +70ºC / 5 to 95% non-condensing
6mm2 flying leads
Environmental
IP 65
Weight
160g
AS/NZS 1768
Dimensions
IEEE C62.41
Body diameter
IEC 61643-11
Body length
60mm
IEC 62561-3
Lead length
500mm each (Customizable on request)
20mm
SPECIAL PRODUCTS
EC Earth Clamp 100kA
Novaris EC provides a means to electrically clamp different earthing
systems during transient disturbances. Applications include computer
rooms, defence installations and gas pipeline insulated joints.
EC 100 - 230
350V
EC100-800
230V
EC100-500
EC100-350
Uc
EC100-230
Product Series Imax
Electrical Specifications
Active element
DC spark over voltage
Gas Discharge Tube (GDT)
Uc
Voltage tolerance
Discharge current 8/20µs
Imax
Voltage protection level @ 5kV (10/700µs)
UP
Isolation resistance
Capacitance
500V
800V
<1200V
<1500V
± 20%
100kA
<900V
<1000V
>10 W
10
<4pF
Mechanical Specifications
Operating temperature / humidity
Connection type
-40 to +70ºC /5 to 95% non-condensing
10mm2 flying leads
Environmental
IP 65
Weight
200g
Dimensions
Standards Compliance
AS/NZS 1768
IEEE C62.41
Body diameter
30mm
Body length
100mm
Lead length
500mm each (Customizable on request)
IEC 61643-11
Options [*]
IEC 62561-3
Heatshrink Enclosure
HS
49
SPECIAL PRODUCTS
EKIT Cable Bonding Kit
Novaris Cable Bonding Kits are used to bond the shields of coaxial feeders
and wave guides on communication towers and at cable entry points to
communications buildings.
EKIT - 012
EKIT-158
EKIT-078
EKIT-012
Cable size
EKIT-038
EKIT-014
Product Series Electrical Specifications
Connection type
Cable clamp
Sheath connection
25mm braid
900mm 6mm2 flying lead
Earth connection
Cable sealing
Coaxial cable size
50
Self amalgamating upper and lower seals
1/4”
3/8”
1/2”
7/8”
1 5/8”
SPECIAL PRODUCTS
TSC Transient Surge Counter
Novaris Transient Surge Counters count direct lightning strikes and transient
events. They may be clamped to the downconductor of a building or
tower or in the earth return conductor of a surge diverter or filter. The EC
version also acts as a transient earth clamp.
TSC1 - DIN - EC
TSC1-DIN
TSC1-DIN-EC
Earth Clamp
TSC1-IP65
Product Series Type
Electrical Specifications
Sensitivity
150A
DC spark over voltage
Uc
-
230V
Discharge current 8/20µs
Imax
-
150kA
Battery life of counter
7 years
Display
Resettable, LCD
Active element
-
GDT
Voltage tolerance
-
± 20%
Isolation resistance
-
>1010W
Capacitance
-
<4pF
Mechanical Specifications
Operating temperature / humidity
Terminal capacity
Terminal screw torque
-40 to +70ºC /5 to 95% non-condensing
-
16mm2
-
2.5Nm
Environmental
IP 65
IP 20
Mounting
Clamp
TS35 DIN rail
-
2-way plug
400g
600g
Counter connection
Weight
Dimensions
Width
80mm
54mm
Standards Compliance
Height
110mm
95mm
IEC 62561-6
Depth
65mm
80mm
51
Standards and Safety
Standards
Many countries have comprehensive lightning protection standards. As a global provider of lightning
and surge protection solutions Novaris strives to provide its solutions in accordance with recognised
world standards.
As an Australian company Novaris conforms strictly to the guidelines contained in the Australian and
New Zealand standard on lightning protection AS/NZS1768:2007.
Additionally Novaris’ solutions and products conform to the relevant IEC standards, notably IEC62305
(Protection against Lightning) and IEC61643 (Low-voltage Surge Protection Devices).
In line with AS/NZS1768:2007, Novaris does not recommend or endorse the use of so called nonconventional lightning ‘attraction’ or protection systems.
Safety
Because Novaris cares about personnel and equipment safety all our products are subjected to
rigorous testing in our laboratory. We are able to generate most of the test waveforms specified in the
IEC, Australian and US standards. We can test for temporary overvoltage and high current test series
connected or two port SPDs up to 2000A per phase.
Because of the unpredictable nature of lightning transients and the follow on effects of power systems
overvoltages, surge protection components can be overloaded and fail catastrophically. For this reason
our laboratory is equipped to carry out the most severe of destructive tests.
From years of experience we know that surge protection components can rupture and be subject to
excessive heating under fault conditions. It is for this reason that all Novaris power line surge protection
products are housed in robust metal enclosures and we recommend that all SPDs be protected with
appropriate fuses or circuit breakers in accordance with the relevant standards.
52
Risk Assessment
Historically, lightning protection consulting only concentrated on the protection of buildings and
structures. Little thought was ever given to protecting against the indirect effects of lightning strikes
which causes damage to equipment, regardless of whether structural protection is present or not. It
was simply assumed that structural lightning protection would protect everything.
This is far from being the case, and protection against the indirect effects of a lightning strike is often
more important that structural protection.
When it is considered that many modern buildings with steel frames and metal sheet roofing are
inherently self protecting, it is regrettable to see structural lightning protection added for absolutely no
reason, particularly when the indirect protection has been completely ignored.
Fortunately this situation is now recognised and both the IEC and the Australian and New Zealand
lightning protection standards present risk assessment procedures capable of clearly defining the need
for both structural and surge (or indirect) protection. The IEC standard (IEC62305-2) recognizes the need
for both structural and surge protection but mandates that structural protection is necessary whenever
surge protection is needed (Figure 1). The Australian and New Zealand standard (AS/NZS1768:2007)
allows surge protection in the absence of structural protection (Figure 2). This is entirely rational.
Any lightning protection design should first start with a risk assessment. If structural protection is required,
first determine if the structure is self protecting before following the procedures in the standards.
Figure 1. IEC Risk Assessment Procedure
(from IEC62305-2)
Figure 2. Australian and New Zealand Standard
Risk Assessment Procedure
(from AS/NZS1768:2007)
53
Surge Ratings
The ratings of primary and secondary surge protection can be obtained from the Australian Standard.
AS/NZS1768:2007 makes specific recommendations for the surge ratings of surge protection devices.
Figure 3 is taken from this standard.
RECOMMENDED SURGE RATINGS FOR A.C. POWER SYSTEM
SPDs PER PHASE
AS1768
IEC 61643-11
Category
Classification
A
Type III
SPD location
Imax ratings
Long final subcircuits and electricity supply outlets
3-10kA
Major submains, short final subcircuits and load centres
10-40kA
B
Type II
C1
Type I, II
C2
Type I
Service entrance, building fed by long overhead service lines, or is a large
C3
Type I
Service entrance, building in a high lightning area, or fitted with a LPS
Service entrance, other than below
40kA
40-100kA
industrial or commercial premises
100kA
Figure 3. Table 5.1 from AS/NZS1768:2007, IEC 61643-11 Type classification addition
The above table recommends that for main switchboards at sites fitted with a lightning protection system,
or fed with long overhead power lines, the surge rating of primary LV arresters (per phase) should be at
least 100kA for an 8/20µs impulse. Product lifespan, redundancy and improved let through voltages are
benefits to be taken into consideration when selecting products with a higher Imax rating.
All SPDs should be installed in accordance with AS4070, or the equivalent wiring standard for that
country, and be connected between each phase and neutral. At switchboards where there is no MEN,
neutral-earth protection is also required. The neutral-earth protection is generally provided by means of a
high energy gas discharge tube (GDT), with Imax = 100kA.
54
Surge Ratings
Secondary protection generally requires a lower surge rating. Sub-boards within buildings can be regarded
as occupying location category B and surge ratings around 40kA are suitable. The most appropriate surge
protector for these applications is a series connected device, either a series surge protector or surge filter.
These will require all mode protection since there is unlikely to be an MEN link in the equipment cabinet.
The normal configuration of primary and secondary protection would be shunt surge diverters as the
primary protection and suitably rated series protection devices as secondary protection in the sub or
distribution boards.
At sites where primary and secondary protection is required, yet the cable length from MSB to equipment
is short (typically less than 10m), a surge filter protecting the whole site should be considered. This would
have the appropriate category C surge rating plus an LC filter and a final stage of category B surge
protection. The series inductance “builds out” (artificially lengthens) the line. The above is appropriate for
small sites such as cellular basestations, TV translators, remote telemetry field sites etc.
At installations with an MSB and a number of distribution boards, such as a multi-storey building, primary
and secondary protection should be provided. The primary protection would comprise shunt connected
surge diverters fitted to the main switchboard. These provide a path to earth, via the neutral, for the surge
energy.
Note: These SPDs are wired from phase to neutral in accordance with the IEC and other standards. In
countries employing the MEN system the MEN link provides the neutral to earth path. In other countries
the neutral to earth connection may be via a high energy gas discharge tube (GDT).
The effectiveness of this primary protection depends upon how it is installed. In large switchboards
long shunt leads are unavoidable and the voltage let through by such primary protection is unlikely to
be low enough to provide effective protection for sensitive loads. It is generally sufficient to protect the
switchboard.For this reason secondary protection is recommended.
Surge filters provide the best protection and are recommended to protect electronic and computing
equipment. Being series connected these eliminate the degradation caused by long shunt connected
leads; and with an inbuilt low pass LC filter their let through voltage (Up), is low enough to protect the most
sensitive electronic equipment.
55
Installation
Effective surge protection is highly dependant upon installation practices. All Novaris products are
supplied with detailed installation instructions to ensure they are installed correctly. The following
diagrams show examples of power line surge diverter and surge filter installations.
Surge Diverter – Main Switchboard (Figure 4)
Install protection:
- Downstream of the main switch.
- Upstream of all equipment including earth leakage devices where possible.
- Protect with product recommended HRC fuses.
- Keep lead lengths as short as possible to improve let-through voltage.
MEN systems - install single mode (L-N) protection as close to the MEN link as possible.
Non-MEN systems - install all mode (L-N, L-PE, N-PE) protection.
Surge Filter – Distribution Board (Figure 5)
Install all mode protection:
- Downstream of main switch.
- Upstream of all equipment, including earth leakage devices where possible.
- Protect with product recommended HRC fuses where possible or circuit breaker, with current rating
less than or equal to the load current rating of the filter.
- Keep output cables away from input cables.
Surge Diverter – Distribution Board (Figure 6)
Install all mode protection:
- Downstream of main switch.
- Upstream of all equipment, including earth leakage devices where possible.
- Protect with product recommended HRC fuses where possible or circuit breakers.
- Keep lead lengths as short as possible to improve let-through voltage.
Surge Filter – Final Circuit / Equipment (Figure 7)
Install all mode protection:
- Downstream of fuses or circuit breaker with current rating less than or equal to the load current
rating of the filter.
- As close to the equipment as possible.
- Keep output cables away from input cables.
For further details see individual product installation instructions.
56
Installation
Figure 4. Surge Diverter - Main Switchboard.
Figure 5. Surge Filter – Distribution Board.
Figure 7. Surge Filter - Final Circuit/Equipment.
Figure 6. Surge Diverter – Distribution Board.
57
Signalling Protocols
Table 1 outlines some of the most common signalling protocols along with the Novaris surge protection product best suited to
your application. For other signalling protocols please contact Novaris to discuss your protection requirements.
58
Protocol
Signal Type
Novaris Product
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
10/100/1000BaseT
AS-i
BACnet
BACnet
BACnet
BitBus
CAN Bus (Signal)
C-Bus
CC-Link/LT/Safety
CC-Link IE Field
CCTV
CCTV
ControlNet
DALI
Data Highway/Plus
DeviceNet (Signal)
DF1
DirectNET
DirectNET
Dupline (Signal)
Dynalite
EtherCAT
Ethernet Global Data
Ethernet Powerlink
FIP Bus
FINS
FINS
FINS
FOUNDATION Fieldbus H1
FOUNDATION Fieldbus HSE
GE-SRTP
HART
HostLink
HostLink
Interbus
ISDN
KNX TP0/1
KNXnet/IP
Load Cell
MODBUS
MODBUS TCP
P-Net
PieP
Power over Ethernet
Process Bus (P-Bus)
Profibus DP/FMS
Profibus PA
Profinet IO
PSTN
S-Bus
Sercos III
Sinec H1
SynqNet
TTEthernet
xDSL
± 5 VDC, < 250kHz
± 12 VDC, < 250kHz
± 24 VDC, < 250kHz
± 48 VDC, < 250kHz
0-20mA / 4-20mA
RS-232
RS-422
RS-452
RS-485
1-Wire
Ethernet
32 VDC 1-pair
ARCNET / Ethernet / BACnet/IP
RS-232
RS-485
RS-485
5 VDC 1-Pair
36 VDC 1-pair
RS-485
Ethernet
Coaxial
Power over Ethernet
Coaxial
Digital Serial Interface
RS-485
5 VDC 1-Pair
RS-232
RS-232
RS-485
5 VDC 1-Pair
DyNet
Ethernet
Ethernet
Ethernet
RS-485
Ethernet
RS-232
DeviceNet (Signal)
32 VDC 1-pair
Ethernet
Ethernet
4-20mA + HF Data
RS-232
RS-422
RS-485
PSTN
30 VDC 1-pair
Ethernet
Wheatstone Bridge
RS-485
Ethernet
RS-485
Ethernet
Power over Ethernet
RS-485
RS-485
32 VDC 1-pair
Ethernet
POTS
32 VDC 1-pair
Ethernet
Ethernet
Ethernet
Ethernet
PSTN
SL7v5-G
SL18-G
SL36-G
SL68-G
SL420-G
DB9-RS232
SL485-EC90 (x2)
SL485-EC90 (x2)
SL485-EC90
SL485-EC90
RJ45-xCAT6
SL36-G
RJ45-xCAT6
DB9-RS232
SL485-EC90
SL485-EC90
SL-DH
SSP6A-38
SL485-EC90
RJ45-xCAT6
CLB-MF-10
RJ45-xPoE
CLB-MF-10
SL36-G
SL485-EC90
SL7v5-G
DB9-RS232
DB9-RS232
SL485-EC90
SL7v5-G
RJ45-xPoE
RJ45-xCAT6
RJ45-xCAT6
RJ45-xCAT6
SL485-EC90
RJ45-xCAT6
DB9-RS232
SL7v5-G
SSP6A-38-G
RJ45-xCAT6
RJ45-xCAT6
SL-DH
DB9-RS232
SL485-EC90 (x2)
SL485-EC90
SL-PSTN
SL36-G
RJ45-xCAT6
LCP-36
SL485-EC90
RJ45-xCAT6
SL485-EC90
RJ45-xCAT6
RJ45-xPoE
SL485-EC90
SL485-EC90
SL36-G
RJ45-xCAT6
SL-PSTN
SL36-G
RJ45-xCAT6
RJ45-xCAT6
RJ45-xCAT6
RJ45-xCAT6
SL-PSTN
Table 1. Signalling Protocols.
IECEx ia models available with the Novaris Hazardous Area range
SLT1-7v5
SLT1-18
SLT1-36
SLT1-68
SLT1-36
DB25-RS232
DB9-RS485
DB9-RS485
DB9-RS485
DB9-RS485
SL-DH
SLT1-36
DB25-RS232
DB9-RS485
DB9-RS485
DB9-RS232
SL-DH
DB9-RS485
SLT1-36
DB9-RS485
SLT1-7v5
DB25-RS232
DB25-RS232
DB9-RS485
SLT1-7v5
SL-DH
SL-DH
DB9-RS485
DB25-RS232
SLT1-7v5
SLT1-36
SL-DH
DB25-RS232
DB9-RS485
DB9-RS485
KP1/10/i
SLT1-36
SL-DH
MPP-RJxx
DB9-RS485
DB9-RS485
DB9-RS485
DB9-RS485
SLT1-36
KP1/10/i
SLT1-36
MPP-RJxx
KP1/10/i
MPP-RJxx
Glossary
PhPhase
Iimp
Defined by three parameters, a current peak value, a charge and a specific energy.
Generally relates the IEC definition of a direct lightning strike modelled by a 10/350µs
waveshape. This is used for the classification of SPDs for test class I in accordance with
T h e U l t i m a t e H i g h Vo l t a g e Te s t
IEC61643-11.
Q
Charge contained in a test waveform. Expressed in coulombs (As).
W/R
Specific Energy relating to a test waveform. Expressed in kJ/µs.
Imax
Defined as the peak value of a current through the SPD having an 8/20µs waveshape.
This is used for the classification of SPDs for test class II in accordance with IEC61643-11.
This is generally recognized for MOV based SPDs as the single shot impulse rating.
In
Defined as the peak value of a current through the SPD having an 8/20µs waveshape. This
is used for the classification of SPDs for test class II in accordance with IEC61643-11. This
is known as the nominal discharge current and is generally recognized for MOV based
SPDs as the rating of the SPD for 15 such impulses.
IL
The maximum continuous RMS or DC current that can be supplied to a load connected to a
two port or series connected SPD.
If
The current supplied by the electrical power system which flows through an SPD after a
discharge current impulse. This is called the follow-on current and is particularly applicable
to voltage switching type SPDs such as spark gaps and gas discharge tubes.
Ifi
Follow-on current interrupting rating. This is the maximum AC RMS current that a voltage
switching SPD such as a spark gap can interrupt.
U0
The RMS line to neutral voltage of the power system.
U c
The maximum RMS or DC voltage, which may be continuously applied to an SPD.
U p
The let through voltage of an SPD defined for a specified test waveform.
tA
Response time of an SPD to a defined test waveform.
DU
Voltage drop of a two port SPD at rated current expressed as a percentage of U0.
f c
The maximum usable frequency.
Photographer: Renee Doyle
Q1 Building - Gold Coast, Queensland AUSTRALIA
Lightning Protection Consultants:
Surge Protection Design and Manufacture:
Powercom Consultants Pty Ltd
Novaris Pty Ltd
This was the ultimate high voltage test of The Novaris Systematic Approach
to lightning and surge protection.
Jan 2016
59
Global Solutions in Lightning and Surge Protection
72 Browns Road Kingston
P.O. Box 2010 Kingston
Tasmania 7050 Australia
Telephone: +61 3 6229 7233
Facsimile: +61 3 6229 9245
Email: Web Page: © Copyright 2016
[email protected]
www.novaris.com.au
PRODUCT HANDBOOK 2016
Distributed By:
Global Solutions in
Lightning and Surge Protection
PRODUCT HANDBOOK
Novaris
Novaris Pty Ltd
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement