Soundmaster HighLine DISC 3220USB Product User Manual

DEUTSCH

ENGLISH

FRANÇAIS

NEDERLANDS

ESPAÑOL

DISC 3220USB

ENVIRONMENTAL PROTECTION

Do not dispose of this product with the normal household waste at the end of its life cycle. Return it to a collection point for the recycling of electrical and electronic devices. This is indicated by the symbol on the product, user manual or packaging.

The materials are reusable according to their markings. By reusing, recycling or other forms of utilization of old devices you make an important contribution to the protection of our environment.

Please contact your local authorities for details about collection points.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LASER CLASE 1

CAUTION - INVISIBLE LASER RADIATION WHEN OPENING

THE COVER OR PRESSING THE SAFETY INTERLOCK. AVOID

EXPOSURE TO THE LASER BEAM.

WARNING

Risk of electric shock

Do not open!

Caution: To reduce the risk of electric shock, do not remove the cover (or back).

There are no user serviceable parts inside. Refer servicing to qualified service personnel.

This symbol indicates the presence of dangerous voltage inside the enclosure, sufficient enough to cause electric shock.

This symbol indicates the presence of important operating and maintenance instructions for the device.

Safety, Environmental and Setup Instructions

•

Use the device in dry indoor environments only.

•

Protect the device from humidity.

•

Do not open the device. RISK OF ELECTRIC SHOCK! Refer opening and servicing to qualified personnel.

• Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with the specifications on the rating plate.

•

Make sure the mains cable stays dry during operation. Do not pinch or damage the mains cable in any way.

•

A damaged mains cable or plug must immediately be replaced by an authorized service center.

•

In case of lightning, immediately disconnect the device from the mains supply.

•

Children should be supervised by parents when using the device.

•

Clean the device with a dry cloth only.

Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS!

•

Do not expose the device to direct sunlight or other heat sources.

•

Install the device at a location with sufficient ventilation in order to prevent heat accumulation.

•

Do not cover the ventilation openings!

•

Install the device at a safe and vibration-free location.

• Install the device as far away as possible from computers and microwave units; otherwise radio reception may be disturbed.

• Do not open or repair the enclosure. It is not safe to do so and will void your warranty. Repairs only by authorized service/ customer center.

•

The device is equipped with a “Class 1 Laser”. Avoid exposure to the laser beam as this could cause eye injuries.

•

Only use mercury and cadmium-free batteries.

•

Used batteries are hazardous waste and NOT to be disposed of with the household waste!!! Return the batteries to your dealer or to collection points in your community.

• Keep batteries away from children. Children might swallow batteries. Contact a physician immediately if a battery was swallowed.

•

Check your batteries regularly to avoid battery leakage.

Used batteries are hazardous waste and NOT to be disposed

of with the household waste! As a consumer you are legally

obligated to return all batteries for environmentally responsible recycling – no matter whether or not the batteries contain harmful substances*).

Return batteries free of charge to public collection points in your

community or to shops selling batteries of the respective kind.

Only return fully discharged batteries.

*) marked Cd = cadmium, Hg = mercury, Pb = lead

ENGLISH

LOCATION OF CONTROLS

2) ALARM 2 BUTTON

3) ALARM 1 BUTTON

5) POWER ON / STANDBY

7) STANDBY LED INDICATOR

BUTTON

9) PRESET EQ BUTTON

10) VOLUME UP BUTTON

11) SNOOZE BUTTON

12) LCD DISPLAY

13) MEMORY / CLOCK-ADJUST BUTTON

14) MP3 FOLDER / PRE-UP BUTTON

15) SKIP / TUNING UP

BUTTON

16) 3.5MM HEADPHONE JACK

17) PLAY/PAUSE

/ FM ST/MO BUTTON

18) STOP

/

BAND BUTTON

19) CD DOOR OPEN/CLOSE BUTTON

20) PLAY MODE BUTTON

21) SKIP / TUNING DOWN

22) SD/MMC CARD SLOT

BUTTON

23) USB SOCKET

24) 75 OHM FM SOCKET

25) AM ANTENNA LOOP SOCKET

26) 3.5MM AUX-IN JACK

27) SPEAKER JACK (L/R)

28) AC POWER CORD

CAUTION:

USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL.

IMPORTANT:

SINCE MOVEMENT OF THE CD MECHANISM AND THE SENSITIVE CIRCUITY MAY CAUSE INTERFERENCE TO

THE RADIO TUNER NEARBY, SWITCH THIS UNIT OFF WHILE OPERATING OTHER

RADIO DEVICES.

PRECAUTIONS FOR USE

INSTALLATION

•

UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.

• DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAIN VOLTAGE AND BEFORE ALL

OTHER CONNECTIONS HAVE BEEN MADE.

• DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS

AROUND THE UNIT FOR VENTILATION.

ENG 1

ENGLISH

INSTALLATION

FOR TABLE TOP USE

INSET THE STAND TO THE MAIN UNIT AND SPEAKER BOX REFER TO THE PICTURE

FOR WALL MOUNTING

1) UN-INSTALL SPEAKER BOX AND THE STAND IN THE REVISE WAY FROM ABOVE

2) USE THE WALL-MOUNTING TEMPLATE SUPPLIED WITH THE UNIT TO MAKE ANCHOR HOLE MARKS ON

THE WALL. MAKE SURE THE MARKS ARE LEVEL.

3) DRILL 1/4” HOLES ON THE MARKS.

4) INSERT THE PLASTIC ANCHOR SUPPLIED WITH UNIT IT IS FLUSH WITH THE WALL.

5) INSERT THE SCREW AND TIGHTEN THE SCREW 4MM AWAY FROM THE WALL. (APPROXIMATELY THE

WIDTH OF 2 PENNIES) HANG THE MAIN UNIT AND SPEAKERS TO THE SCREW AS INDICATED BELOW:-

CONNECTION

1. CONNECT THE POWER CORD (28) TO AC OUTLET

2. WHEN YOU FIRST PLUG THE UNIT INTO THE MAINS, THE UNIT WILL GO INTO STANDBY MODE AND THE

STANDBY LED INDICATOR (7) WILL LIGHT UP.

3. CONNECT THE SPEAKER WIRE TO THE SPEAKER JCK (27) LOCATED ON THE SIDE OF UNIT.

4. TURN ON THE POWER (5), IF THE LCD DISPLAY (12) IS ON WITH BACKLIGHTING, IT MEANS THE POWER

SUPPLY IS NORMAL. NOW YOUR SYSTEM IS READY TO PLAY THE MUSIC.

SETTING THE CLOCK

1. SET UNIT IN STANDBY MODE.

2. PRESS & HOLD THE “ MEM/CLK-ADJ ” BUTTON (13), THE LCD DISPLAY (12) WILL SHOW “ 12HR ” OR “ 24 HR “.

PRESS SKIP UP OR SKIP DOWN BUTTON (15,21) TO SELECT THE APPROPIATE AREA HOUR

FORMAT(12HR/24HR). PRESS “MEM/CLK-ADJ” BUTTON (13) AGAIN TO CONFIRM.

3. THE LCD DISPLAY (12) WILL DISPLAY THE SECOND DIGIT OF “0 ” IS FLASHING. PRESS SKIP UP OR

SKIP DOWN BUTTON (15,21) TO SET THE CORRECT HOUR. PRESS “ MEM/CLK-ADJ ” BUTTON (13) TO

STORE THE CORRECT HOUR.

4. THE THIRD & FOURTH DIGIT OF “ 00 ” IS FLASHING, PRESS THE SKIP UP OR SKIP DOWN

BUTTON (15,21) TO SET THE CORRECT MINUTES. THEN PRESS “ MEM/CLK-ADJ ” BUTTON (13) TO STORE

THE CORRECT MINUTE.

¾

THE PRE-SET TIME WILL BE RE-SET COMPLETELY IF DIS-CONNECTING THE MAIN POWER

SUPPLY. YOU ARE RECOMMENDED TO SWITCH THE SYSTEM INTO STANDBY MODE FOR

CONVENIENCE USAGE.

ENG 2

ENGLISH

LISTENING TO RADIO

MANUAL TUNING

1. PRESS FUNCTION BUTTON (6) TO SELECT “ TUNER ” MODE.

2. PRESS “ STOP

/

BAND ” BUTTON (18) TO SELECT DESIRED BAND (AM OR FM).

3. TUNE TO THE REQUIRED STATION BY PRESSING THE TUNE “ + ” OR “

− ” BUTTON (15,21).

4. ADJUST VOLUME UP/DOWN BUTTON (10,4) TO THE DESIRED VOLUME LEVEL.

AUTO TUNING

1. PRESS FUNCTION BUTTON (6) TO SELECT “ TUNER ” MODE.

2. PRESS “ STOP

/

BAND ” BUTTON (18) TO SELECT DESIRED BAND (AW OR FM).

3. PRESS AND HOLD THE TUNE “ + ” OR “

− ” BUTTON (15,21) FOR 1-2 SECONDS AND THEN RELEASE.

4. THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP UNTIL A RADIO STATION IS REACHED.

5. REPEAT STEP 3 & 4 UNTIL THE DESIRED RADIO STATION IS BEING REACHED.

6. ADJUST VOLUME UP/DOWN BUTTON (10,4) TO THE DESIRED VOLUME LEVEL.

PRESET STATIONS (BY REMOTE CONTROL)

YOU CAN STORE UP TO 20 RADIO STATIONS IN THE MEMORY (10 AM / 10 FM).

1. SET TO TUNER MODE.

2. TURN TO THE DESIRED RADIO STATION BY “ MANUAL” OR “ AUTO ” TUNING METHOD.

3. PRESS “ MEM/CLK-ADJ ” BUTTON TO ENABLE PROGRAM FUNCTION & “ MEM ” INDICATOR IS SHOW ON

LCD DISPLAY (12)

4. PRESS “ FOLDER / PRE-UP OR PRE-DN ” BUTTON TO SELECT THE DESIRED STATION MEMORY FOR

STORAGE.

5. PRESS “ MEM/CLK-ADJ ” BUTTON AGAIN TO CONFIRM THE SETTING.

6. REPEAT STEP 2 TO 5 TO STORE OTHER STATIONS.

7. NOW YOU CAN SELECT THE PRESETS STATIONS IN ORDER BY PRESSING THE “FOLDER/PRE–UP ”

BUTTON OR PRE-DN BUTTON.

¾

THE PRE-SET MEMORIES WILL BE CANCELLED COMPLETELY IF DIS-CONNECTING THE MAIN POWER

SUPPLY. YOU ARE RECOMMENDED TO SWITCH THE SYSTEM INTO STANDBY MODE FOR CONVENIENCE

USAGE.

¾

THERE ARE ABOUT 10 SECONDS FOR PROGRAM STATE, AFTER 10 SEC. THIS STATE WOULD RESUME

TO NORMAL TUNER MODE AUTOMATICALLY.

¾

YOU CAN OVERWRITE A PRESENT STATION BY STORING ANOTHER FREQUENCY IN ITS PLACE.

FM & FM-STEREO RECEPTION

z PRESS THE “ ST/MONO ” BUTTON (17) REPEATEDLY, THE FM PROGRAMS ARE RECEIVING IN MONO AND

STEREO MODE REPEATEDLY. IN PARTICULAR WHEN STEREO SIGNALS ARE WEAK. IT IS PREFERABLE TO

RECEIVE THE PROGRAM IN MONO. z IF STEREO SIGNAL IS BEING RECEIVED, THE STEREO INDICATOR “

DISPLAY (12) TO SHOW FM STEREO PROGRAM IS NOW RECEIVING.

” WILL APPEAR ON LCD

HINTS FOR BEST RECEPTION:-

- AM : THE RECEIVER USING A EXTERNAL AM LOOP ANTENNA AND CONNECT THE AM ANTENNA TO THE AM

SOCKET (25) WHICH LOCATED AT THE SIDE OF MAIN UNIT. IF AM RECEPTION IS WEAK, SLIGHT ROTATE

OR RE-POSITIONING THE LOOP ANTENNA WILL USUALLY IMPROVE THE AM RECEPTION.

- FM : CONNECT THE FM SOCKET (36) VIA A 75 OHM CABEL (NOT PROVIDED) FOR THE BEST RECEPTION.

PLAYING COMPACT DISC

z GETTING START

1. PRESS FUNCTION BUTTON (6) TO SELECT “ CD ” MODE,

2. PRESS “ CD DOOR OPEN/CLOSE ” BUTTON (19) TO OPEN THE CD DOOR.

3. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO DOOR BY

PRESSING THE “ CD DOOR OPEN/CLOSE ” BUTTON (19) AGAIN.

4. FOCUS SEARCH IS PERFORMING, THE LCD DISPLAY (12) WILL SHOW THE TOTAL NUMBER OF TRACKS &

TOTAL PLAYING TIME.

z PLAY / PAUSE MODE

1. PRESS THE “ PLAY/PAUSE ” BUTTON (17) TO START PLAYBACK, THE FIRST TRACK WILL START

PLAYBACK.

2. TO INTERRUPT, PRESS THE “ PLAY/PAUSE ” BUTTON (17) ONCE, AND THE PLAYING TIME WILL BE

FREEZE ON THE LCD DISPLAY (12). PRESS AGAIN TO RESUME NORMAL PLAYBACK.

ENG 3

ENGLISH

z STOP MODE

1. IF “ STOP ” BUTTON (18) IS PRESSED DURING PLAY OR PAUSE MODE, SYSTEM WILL GO TO STOP

MODE.

z SKIP MODE (SKIP UP

/ SKIP DOWN )

1. DURING PLAY OR PAUSE MODE, IF “ SKIP UP ” BUTTON (15) IS PRESSED. IT WILL GO TO NEXT TRACK

AND DISPLAY THE TRACK NO. AND THEN REMAIN THE PLAY OR PAUSE MODE.

2. DURING PLAY OR PAUSE MODE, IF “ SKIP DOWN ” BUTTON (21) IS PRESSED. IT WILL GO BACK TO THE

BEGINNING OF THE TRACK, ORIGINAL TRACK NO. IS DISPLAY AND REMAIN THE PLAY OR PAUSE MODE.

3. AFTER STEP 2, PRESS “ SKIP DOWN ” BUTTON (21) AGAIN WILL GO TO THE PREVIOUS TRACK AND

REMAIN THE PLAY OR PAUSE MODE.

z FOR MP3 DISC

1. AFTER FOCUS SEARCH IS PERFORMING, THE TOTAL NUMBER OF TRACK AND ALBUM WILL BE SHOWN

ON THE LCD DISPLAY (12).

2. PRESS “ FOLDER/ PRE-UP OR PRE-DN ” AT REMOTE CONTROL TO SELECT THE FOLDER NUMBER.

3. PRESS “ SKIP UP OR SKIP DOWN ” BUTTON (15,21) TO SELECT THE TRACK NUMBER.

4. WHEN THE DESIRED TRACK AND FOLDER IS BEING SELECTED, PRESS THE “ PLAY/PAUSE ” BUTTON

(17) TO START PLAYBACK.

ID3 (TRACK/ALBUM TITLE) FUNCTION (BY REMOTE HANDSET)

PRESS THE “ ID3 “ BUTTON UNTIL THE LCD DISPLAY (12) SHOW “ FILE -

… ”DURING PLAYBACK OF MP3/WMA

FILE, THE SONG TITLE / ARTIST NAME / ALBUM NAME IS BEING DISPLAYED IN SEQUENCE . PRESS THE “ ID3 ”

BUTTON AGAIN TO DISABLE THE FUNCTION.

REMARK:-

- IN THAT CASE OF NO NAME OR NOT SUPPORTIVE LANGUAGES HAD BEEN ASSIGNED FOR THE TRACK, “ NO

TAG ” TO BE DISPLAYED ON LCD DISPLAY (12) WHEN PRESS THE ID3 BUTTON AT REMOTE.

- NO TITLE/ALBUM NAME CAN BE RECOGNIZED IF THE INPUT FORMAT ON THE DISC/MASS MEDIA IS NOT

SUPPORTING BY THE SYSTEM.

- THE SYSTEM SUPPORT ONLY ENGLISH AND ARABIC NUMBER FOR ID3 FUNCTION

MP3 TRACK FORMAT REQUIREMENT:-

-

BIT RATE : 32 KBPS~320KBPS, SAMPLING RATE : 32KHZ, 44.1KHZ AND 48 KHZ DECODABLE

- THE PERFORMANCE OF PLAYING MP3 DISC IS VARIOUS FROM THE QUALITY OF RECORDING DISC AND

THE METHOD OF RECORDING. FURTHERMORE, THE SEARCHING LEAD-TIME FOR MP3-CD IS LONGER

THAN NORMAL CD DUE TO DIFFERENCE FORMAT.

z REPEAT/INTRO/RANDOM MODE

PRESS THE “ PLAY MODE ” BUTTON (20) DURING PLAYBACK TO SELECT REPEAT AND RANDOM FUNCTION, A

SINGLE TRACK, SINGLE FOLDER (MP3 ONLY) OR ALL THE TRACKS CAN BE PLAYED IN DIFFERENCE MODE AS

FOLLOW:-

FOR CD

(1) REPEAT 1 (2) REPEAT ALL TRACK (3) RANDOM (4) OFF MODE

PLAY MODE

INDICATOR

ON LCD DISPLAY

REPEAT TRACK

REPEAT ALL

& FLASHING

ENG 4

ENGLISH

FOR MP3/WMA DISC/FILE

(1) REPEAT 1 (2) REPEAT 1 FOLER (3) REPEAT ALL TRACKS

(5) OFF MODE

INDICATOR

MODE ON DISPLAY

REPEAT SINGLE TRACK

REPEAT SINGLE FOLDER

REPEAT ALL TRACKS

& FLASHING

(4) RANDOM

z REPEAT PLAY

YOU CAN LISTEN THE DESIRED TRACKS OR FOLDER REPEATEDLY BY THIS FUNCTION.

z RANDOM PLAY

YOU CAN LISTEN ALL THE TRACKS OR FOLDER IN A RANDOM ORDER BY THIS FUNCTION

CD / MP3 DISC PROGRAMMING (BY REMOTE CONTROL)

UP TO 20 TRACKS CAN BE PROGRAMMED FOR DISC PLAY IN ANY ORDER. BEFORE USE, BE SURE TO PRESS

THE “ STOP / BAND ” BUTTON (18).

1. SET IN CD MODE & STOP THE CD PLAYBACK.

2. PRESS THE “ MEM/CLK-ADJ ” BUTTON , “ MEM ” WILL APPEAR ON LCD DISPLAY (12). MOREOVER, IT WILL

INDICATE PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED – “ 001 P01 ”.

3. SELECT A DESIRED TRACK BY PRESSING SKIP UP OR DOWN BUTTON.

4. PRESS THE “ MEM/CLK-ADJ ” BUTTON TO STORE THE TRACK INTO MEMORY.

5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.

6. WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS “ PLAY/PAUSE ” BUTTON TO

PLAY THE DISC IN ASSIGNED ORDER.

7. PRESS “ STOP / BAND ” BUTTON TO TERMINATE PROGRAM PLAY.

¾ AFTER PROGRAM COMPLETE, PRESS “ MEM.CLK-ADJ ” BUTTON TO REVIEW THE TRACKS BEING

PROGRAMMED.

¾ PRESS “ STOP

/BAND ” BUTTON AT CD STOP MODE TO CANCEL ALL PROGRAMMED MEMORY UNTIL

THE “ MEM ” INDICATOR DISAPPEAR ON LCD DISPLAY (12).

¾

FOR MP3 DISC / FILE, PRESS THE “ FOLDER / PRE-UP ” BUTTON TO SELECT THE 1

ST

TRACK OF NEXT

FOLDER DIRECTLY AND HENCE TO SPEED UP THE SONG SLECTION.

¾ THE PROGRAMMING MODEL WILL AUTOMATICALLY STOP IF NO BUTTON IS BEING PRESSED IN A PERIOD

OF ABOUT 1 MINUTES AFTER PRESSING THE “ MEM/CLK-ADJ ” BUTTON. OR PRESS THE “ STOP

/BAND ” BUTTON TO QUITE PROGRAM MODE AT ANY TIME.

PLAYBACK OF MP3/WMA SONG VIA USB STORAGE MEDIA OR MEMORY CARD

CONNECTING

THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 /WMA FILE WHICH STORED IN THE MEMORY

MEDIA WITH USB CONNECTING PORT OR SD/MMC MEMORY CARD.

1. SET THE SYSTEM AT STANDBY MODE FIRST OR OTHER FUNCTION EXCEPT SD

OR USB MODE.

2. PLUG-IN THE USB PEN-DRIVE WITH THE FACE UP & MAKE SURE IT GOING INTO

COMPLETELY OR INSERT THE MEMORY CARD IN THE DIRECTION OF THE

ARROW AS SHOWN IN THE LABEL ON THE UNDERSIDE OF THE MEMORY CARD

SLOT COVER. INSERT STRAIGHT WITHOUT BENDING. z

CONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD DAMAGE THE

AUDIO SYSTEM OR THE STORAGE MEDIA (USB THUMB DRIVE / SD/MMC CARD).

CHECK TO BE SURE THE DIRECTION IS CORRECT BEFORE CONNECTION.

3. SET FUNCTION BUTTON (6) TO “ ” SD/MMC CARD OR “ ” USB MODE.

4. THE SYSTEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY AFTER CONNECTING, AND

LCD DISPLAY (12) WILL SHOW THE TOTAL NUMBER OF MP3/WMA FILES BEING DETECTED.

5. REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3 DISC AS ABOVE.

ENG 5

ENGLISH

REMARK

- THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 OR WMA FORMAT ONLY AT USB/SD MODE

BUT NOT OTHER MUSIC FILE FORMAT.

-

IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3 ENCODING

FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS NOT A

MALFUNCTION OF THE SYSTEM.

-

USB PORT DOES NOT SUPPORT CONNECTION WITH USB EXTENSION CABLE AND IS NOT DESIGNED

FOR COMMUNICATION WITH COMPUTER DIRECTLY

REMOVING OF USB / MEMORY CARD

TO REMOVE THE USB / MEMORY CARD, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO EITHER

CD, AUX OR TUNER FIRST. FOR USB PORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET DIRECTLY, FOR

MEMORY CARD – PULL OUT THE SD/MMC CARD STRAIGHTLY WITHOUT BENDIN..

MORE FEATURES

A. SLEEP SETTING (BY REMOTE CONTROL)

1. PRESS “ SLEEP ” BUTTON AND SLEEP INDICATOR SHOWN ON THE LCD DISPLAY (12).

2. KEEP PRESSING THE BUTTON TO ADJUST THE SLEEP TIMER IN THE ORDER OF 90 > 80 > 70 >……10

MINUTES RESPECTIVELY.

3. SYSTEM WILL STOP AND GOTO STANDBY MODE AUTOMATICALLY AFTER THE SELECTED TIMING.

4. TO CANCEL THE SLEEP MODE, PRESS “ SLEEP ” BUTTON UNTIL THE “

LCD DISPLAY.

“ INDICATOR DISAPPEAR ON

REMARK:-

IF PRESS THE SLEEP BUTTON ONCE AND THE “ ” INDICATOR APPEAR ON THE LCD DISPLAY (12), THE

SYSTEM WILL GOTO STANDBY MODE AUTOMATICALLY AFTER SELECTED MINUTES.

B. ALARM CLOCK SETTING

THIS FUNCTION ALLOWS THE SYSTEM TO TURN ON AUTOMATICALLY AND WAKE YOU UP BY

USB/SD/CD/TUNER OR BUZZ SOUND (ALARM 1 & 2) RESPECTIVELY.

FIRST, SET THE UNIT AT STANDBY MODE AND THEN PRESS THE “ ALARM 1 ” BUTTON (3) TO ENTER THE

SETTING MODE, THE FIRST TWO DIGITS OF CLOCK WILL FLASHING:-

1) WAKE UP TIME : PRESS & HOLD THE “ ALARM 1 ” BUTTON FOR A WHILE UNTIL THE CLOCK ON LCD IS

FLASHING. THEN PRESS SKIP UP / DOWN ” BUTTON (15,21) TO SET THE HOUR &

THEN PRESS “ ALARM 1 ” BUTTON (3) AGAIN TO CONFIRM. THEN PRESS SKIP UP /

DOWN ” BUTTON (15,21) TO SET THE MINUTES & THEN PRESS THE “ ALARM 1

“ BUTTON TO CONFIRM.

2) WAKE UP SOURCE :, PRESS SKIP UP / DOWN ” BUTTON (15,21) TO SELECT THE SOURCE FORM

“ CD ”, SD/MMC, “ USB ” , “ TUNER ”OR “ BUZZER “ REPEATLY. THEN PRESS “ ALARM 1 ”

BUTTON (3) AGAIN TO CONFIRM.

3) WAKE UP VOLUME : PRESS SKIP UP / DOWN ” BUTTON (15,21) TO SET THE WAKE UP VOLUME

LEVEL FROM 1 TO MAX. AND THEN PRESS THE ALARM 1 BUTTON TO CONFIRM.

NOW THE ALARM SETTING IS COMPLETED AND THE ALARM 1 INDICATOR “

REMARK:-

” IS SHOWN ON LCD.

¾

THE SYSTEM PROVIDE DUAL ALARM SETTING “ ALARM 2 ” , YOU CAN PRESET ANOTHER WAKE UP

TIME INDIVIDUALLY BY USING “ ALARM 2 ” BUTTON (2).

¾ IF THERE IS NO MUSIC SOURCE BEING DETECTED (SUCH AS CD) WHEN THE PRESET TIME IS REACHED,

SYSTEM WILL DEFULT TO “ BUZZER ” SOUND FOR WAKE UP MODE AUTOMATICALLY.

¾ FOR TUNER WAKE UP, THE SYSTEM WILL PRESET AT THE LATEST RADIO FRQUENCY BEING LISTENED

BEFORE SWITCHING OFF.

z ACTIVE/DE-ACTIVE TIMER FUNCTION

1. PRESS THE “ ALARM 1 ” BUTTON (3) REPEATLY UNTIL THE TIMER INDICATOR “

DISPLAY (12).

” IS SHOWN ON LCD

2. TO CANCEL ALARM FUNCTION BY PRESS AGAIN “ ALARM 1 ” BUTTON (3) UNTIL THE TIMER INDICATOR

“ ” DISAPPEAR.

REMARK:-

SAME EXECUTION FOR “ ALARM 2 “ MODE

ENG 6

ENGLISH

z SNOOZE FUNCTION

PRESS “ SNOOZE ” BUTTON (11) ONCE TO TERMINATE THE ALARM MODE TEMPORARILY, AND SYSTEM WILL

RE-START AGAIN AFTER 10 MINUTES ON EACH PRESS. TO CANCEL THE ALARM MODE, PRESS THE “ ALARM

1 ” (3) OR “ ALARM 2 ” (2) BUTTON OR “ POWER ON/STANDBY ” BUTTON (5) WHILE SYSTEM IS ON.

C. MUTE FUNCTION (BY REMOTE HANDSET)

PRESS TO TERMINATE THE SOUND OUTPUT FROM SPEAKER TEMPORARILY AND PRESS AGAIN TO RESUME

NORMAL PLAYBACK.

D. PRE-SET EQ FUNCTION

THIS UNIT PROVIDES 5 DIFFERENCES SOUND MODE TO ENHANCE YOUR LISTENING EXPERIENCE. YOU CAN

SELECT THE DESIRED EFFECT BY PRESSING THE “ PRESET EQ ” BUTTON (9) REPEATEDLY AT FOLLOWING

SEQUENCE:-

FLAT CLASSIC ROCK POP JAZZ

AUX-IN CONNECTION

CONNECT ANOTHER AUDIO DEVICE, E.G. (PORTABLE) CD PLAYER, MP3 PLAYER, (PORTABLE) CASSETTE

PLAYER ETC. TO THIS SYSTEM VIA A CORD WITH 3.5MM DIA JACK PLUGS (NOT SUPPLIED).

CONNECT ONE END OF THIS CORD TO THE 3.5MM DIA. HEADPHONE JACK ON THE EXTERNAL DEVICE AND

THE OTHER END TO THE AUX-IN JACK (26) ON THE SIDE OF THE UNIT.

WHEN CONNECTED IN THIS WAY IT IS POSSIBLE TO PLAY BACK THE MUSIC ALREADY ON THE CONNECTED

DEVICE.

REMOTE CONTROL TRANSMITTER

CONTROL FUNCTIONS

BATTERY INSTALLATION (BATTERY NOT PROVIDED)

THE INFRA-RED TRANSMITTER REQUIRE 2 PCS “ AAA ” SIZE BATTERY FOR OPERATION

ENG 7

ENGLISH

BUTTON DESCRIPTION

29) ON/STANDBY

30) MEM / CLK-ADJ

PRESS TO POWER ON / STANDBY THE SYSTEM

IN STANDBY MODE: PRESS & HOLD TO ADJUST CLOCK AND ALARM CLOCK

SETTING

IN CD/USB/SD / TUNER MODE: PRESS TO PRESET MEMORY

31) FUNCTION PRESS TO SELECT THE FUNCTIONS (CD/SD/USB/TUNER /AUX)

32,50) SKIP UP /DOWN / PRESS TO SELECT PREVIOUS / NEXT TRACKS AT CD/USB/SD MODE

TUNE+/- PRESS TO STEP UP/DOWN OF RADIO FREQUENCY AT TUNER MODE

33) STOP / BAND IN TUNER MODE: PRESS TO SELECT THE RADIO BAND

STOP PLAYBACK

34, 49) FOLDER/PRE UP

DOWN

/ IN CD/MP3 MODE: PRESS TO SELECT NEXT OR PREVIOUS FOLDER

IN TUNER MODE: PRESS TO CALL OUT THE PRESET MEMORY IN ORDER

35, 48) -10/ +10 UP /DOWN IN CD MODE: PRESS TO SKIP UP/DOWN THE

TRACK BY 10 MULTIPLE

36) OPEN/CLOSE PRESS DOOR

PRESS TO ADJUST VOLUME LEVEL UP / DOWN 37, 47) VOLUME + /-

38) PLAY MODE IN CD/MP3 MODE: PRESS TO ACTIVE

REPEAT AND RANDOM PLAY FUNCTION

39) PRESET EQ PRESS TO SELECT DIFFERENCE EQ MODE FOR ENJOYMENT

42) IN

PRESS TO PRESET AND ACTIVE ALARM 2 FUNCTION 43) ALARM 2

44) ALARM 1 PRESS TO PRESET AND ACTIVE ALARM 1 FUNCTION

46) NO FUNCTION THIS BUTTON HAS NO FUNCTION FOR THIS MODEL

51) ST/MONO / PLAY/PAUSE IN TUNER MODE: PRESS TO SELECT FM STEREO OR MONO PLAYBACK

IN CD MODE: PRESS TO START PLAYBACK / PAUSE MODE

TECHNICAL SPECIFICATIONS

FM FREQUENCY:

AM FREQUENCY:

87,5 – 108MHZ

522 – 1620KHZ

POWER CONSUMPTION: 35W

BATTERIES REMOTE CONTROL: 3V 2X UM-4 / AAA (BATTERIES NOT INCL.)

Copyright by Woerlein GmbH, 90556 Cadolzburg, www.woerlein.com

Specification and any technical changes without any further announcement

ENG 8