DATA SHEET: 4 Channel Analog Input Card

DATA SHEET: 4 Channel Analog Input Card
DATA SHEET: 4 Channel Analog Input Card
4 Channel Analog Input Card
The analog input card provides four channels of mic/line input with +48 volts phantom power,
54 dB of gain and 24 dB of trim. The inputs are electronically balanced and provided on plugin barrier strip connectors. Control of each input includes gain with metering, trim, mute and
signal inversion.
Features:
•
Mic/line input card. Up to 4 cards per frame.
•
+48 volts phantom power.
•
54 dB of mic pre-amp gain.
•
Extended dynamic range of 115 dB.
•
Field swappable by certified technicians.
Specifications
Number of Inputs
Four (4) switchable balanced mic or line level.
CMRR
> 76 dB @ 1 kHz, unity gain.
Connectors
3.81 mm terminal blocks.
Input Impedance
8k Ohms balanced, 4k Ohms unbalanced.
Nominal Input Level
+4 dBu with 20 dB of headroom.
Phantom Power (per input)
+48 VDC @ 10 mA maximum.
Maximum Input Level
+23 dBu
Dynamic Range
> 115 dB, A-weighted.
Mic Pre-amp Gain
0, 11.8, 24, 44 or 54 dB switchable
with ± 24 dB trim.
THD + Noise
< -94 dB, unweighted; 1 kHz @ +22 dBu
with 0 dB gain.
Mic Pre-Amp EIN
< -127dB with 150 Ohm source impedance.
Latency
0.28 mS
Mechanical Data
Items
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet 4 Channel Analog Input Card.
The device shall provide four analog mic/line inputs to an EDGE or RADIUS AEC frame that are adjustable from line to mic level with coarse gain, fine trim and phantom power. Up to four
of these devices may be installed in a single EDGE frame for up to sixteen channels of local input and up to one of these devices may be installed in a single RADIUS AEC frame for up to
four channels of local input. Levels, phantom powers, signal inversions and mutes shall be controllable via software. Audio inputs shall be accessed via rear panel 3.81 mm terminal block
connectors.
Audio conversion shall be 24-bit, 48 kHz. The dynamic range shall not be lower than 115 dB, A-weighted with a maximum input level of +23 dBu.
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet Radius AEC or EDGE frame I/O card slot. The device shall be a Symetrix SymNet 4 Channel Analog Input Card.
Copyright 2013, Symetrix, Inc. All Rights Reserved. All specifications and features subject to change without notice.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
DATA SHEET: 4 Channel Analog Output Card
4 Channel Analog Output Card
The analog output card provides four channels of line level output. The outputs are
electronically balanced and provided on plug-in barrier strip connectors. Control of each
output includes gain with metering and mute.
Features:
•
Line output card. Up to 4 cards per frame.
•
+24 dBu maximum output level.
•
+12 dB to off of gain.
•
Extended dynamic range of 117 dB.
•
Field swappable by certified technicians.
Specifications
Number of Outputs
Four (4) balanced line level.
Output Impedance
300 Ohms balanced, 150 Ohms unbalanced.
Connectors
3.81 mm terminal blocks.
Dynamic Range
> 117 dB, A-weighted.
Nominal Output Level
+4 dBu with 20 dB of headroom.
THD + Noise
< -95 dB, unweighted; 1 kHz @ +22 dBu
with 0 dB gain.
Maximum Output Level
+24 dBu (+22.8 dBu into a 2k Ohm minimum load).
Latency
0.60 mS
Mechanical Data
Items
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet 4 Channel Analog Output Card.
The device shall provide four analog line outputs to an EDGE or RADIUS AEC frame that are adjustable with fine trim. Up to four of these devices may be installed in a single EDGE frame
for up to sixteen channels of local output and up to one of these devices may be installed in a single RADIUS AEC frame for up to four channels of local output. Levels and mutes shall be
controllable via software. Audio outputs shall be accessed via rear panel 3.81 mm terminal block connectors.
Audio conversion shall be 24-bit, 48 kHz. The dynamic range shall not be lower than 117 dB, A-weighted with a maximum output level of +24 dBu.
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet Radius AEC or EDGE frame I/O card slot. The device shall be a Symetrix SymNet 4 Channel Analog Output Card.
Copyright 2013, Symetrix, Inc. All Rights Reserved. All specifications and features subject to change without notice.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
DATA SHEET: 4 Channel Digital Input Card
4 Channel Digital Input Card
The digital input card provides four channels of digital input in AES or S/
PDIF format and 24 dB of trim. The inputs are provided on plug-in barrier
strip connectors. Control of each input includes metering, trim, mute and
signal inversion.
Features:
•
Digital audio input card. Up to 4 cards per frame.
•
Supports AES/EBU or S/PDIF.
•
Sample rate conversion on all inputs.
•
Sync range of 12 to 96 kHz.
•
Field swappable by certified technicians.
Specifications
Number of Inputs
Two (2) pairs of switchable AES or S/PDIF format (4
channels total).
Dynamic Range
> 128 dB, unweighted.
Connectors
3.81 mm terminal blocks.
THD + Noise
< -125 dB, unweighted.
Nominal Input Level
-20 dBFS (+4 dBu with 20 dB of headroom).
Nominal Sample Rate
48 kHz
Maximum Input Level
0 dBFS (+24 dBu)
Sample Rate Sync Range
12 to 96 kHz.
Input Impedance
110 Ohms (AES), 75 Ohms (S/PDIF).
Latency
2.1 mS @ 48 kHz
Mechanical Data
Items
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet 4 Channel Digital Input Card.
The device shall provide two pairs of digital inputs (4 channels total) to an EDGE or RADIUS AEC frame that are adjustable with fine trim and selectable in format between AES or S/PDIF.
Up to four of these devices may be installed in a single EDGE frame for up to sixteen channels of local input and up to one of these devices may be installed in a single RADIUS AEC
frame for up to four channels of local input. Levels, mutes, inversions and formats shall be controllable via software. Audio inputs shall be accessed via rear panel 3.81 mm terminal block
connectors.
Audio conversion shall be 24-bit, 48 kHz with ability to accept 12 to 96 kHz using a sample rate conversion. The dynamic range shall not be lower than 128 dB, unweighted with a
maximum input level of 0 dBFS (+24 dBu).
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet Radius AEC or EDGE frame I/O card slot. The device shall be a Symetrix SymNet 4 Channel Digital Input Card.
Copyright 2013, Symetrix, Inc. All Rights Reserved. All specifications and features subject to change without notice.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
DATA SHEET: 4 Channel Digital Output Card
4 Channel Digital Output Card
The digital output card provides four channels of digital output in AES
or S/PDIF format with clock inputs to sync the outputs to a sample rate
of your preference. The outputs are provided on plug-in barrier strip
connectors. Control of each output includes gain with metering and
mute.
Features:
•
Digital audio output card. Up to 4 cards per frame.
•
Supports AES/EBU or S/PDIF.
•
Nominal output sample rate of 48 kHz.
•
Supports external clock input of 12 to 96 kHz.
•
Field swappable by certified technicians.
Specifications
Number of Outputs
Two (2) pairs of switchable AES or S/PDIF format (4
channels total).
Dynamic Range
> 128 dB, unweighted.
Connectors
3.81 mm terminal blocks.
THD + Noise
< -125 dB, unweighted.
Nominal Output Level
-20 dBFS (+4 dBu with 20 dB of headroom).
Nominal Sample Rate
48 kHz
Maximum Output Level
0 dBFS (+24 dBu)
Sample Rate Sync Range
12 to 96 kHz
Output Impedance
110 Ohms (AES), 75 Ohms (S/PDIF).
Latency
2.1 mS @ 48 kHz
Mechanical Data
Items
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet 4 Channel Digital Output Card.
The device shall provide two pairs of digital outputs (4 channels total) to an EDGE or RADIUS AEC frame that are adjustable with fine trim and selectable in format between AES or S/
PDIF. Up to four of these devices may be installed in a single EDGE frame for up to sixteen channels of local output and up to one of these devices may be installed in a single RADIUS
AEC frame for up to four channels of local output. Levels, mutes, clock sources and formats shall be controllable via software. Audio outputs shall be accessed via rear panel 3.81 mm
terminal block connectors.
Audio conversion shall be 24-bit, 48 kHz with ability to accept 12 to 96 kHz using an external clock source. The dynamic range shall not be lower than 128 dB, unweighted with a
maximum output level of 0 dBFS (+24 dBu).
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet Radius AEC or EDGE frame I/O card slot. The device shall be a Symetrix SymNet 4 Channel Digital Output Card.
Copyright 2013, Symetrix, Inc. All Rights Reserved. All specifications and features subject to change without notice.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
DATA SHEET: 4 Channel AEC Input Card
4 Channel AEC Input Card
A single Edge frame has four configurable card slots, providing up to
16 channels of local IO. The AEC input card provides four channels of
transparent Acoustic Echo Cancellation (AEC), with phantom power, 54
dB of gain and 24 dB of trim. Symetrix’ latest generation AEC provides
wideband processing with tail lengths up to 250 mS, and covergence
times greater that 100 dB/S. Symetrix AEC latency is an industry
low 11 mS and near zero bypassed. Each channel of AEC features
discreet reference inputs and direct outputs for local reinforcement.
AEC processing may be applied to any SymNet system input while
still allowing the card’s inputs to be used. The inputs are electronically
balanced using plug-in barrier strip connectors. Control of each input
includes gain with metering, trim, mute, AEC, noise cancellation, nonlinear processing, and AGC (Automatic Gain Control).
Features:
•
Wideband dedicated processing. Does not consume Edge DSP
resources.
•
Zero-latency direct outputs and discrete reference inputs per AEC channel.
•
AEC processing available to the card’s direct inputs or internally routed sources.
•
11 mS AEC latency, up to 250 mS tail length, and greater than 100 dB/S convergence time.
•
Field swappable by certified technicians.
Specifications
Number of Inputs
Four (4) acoustic echo cancellation.
Input Impedance
8k Ohms balanced, 4k Ohms unbalanced.
Connectors
3.81 mm terminal blocks.
Phantom Power
+20 VDC @ 10 mA maximum.
Nominal Input Level
+4 dBu with 20 dB of headroom.
A/D Dynamic Range
< 115 dB, A-weighted.
Maximum Input Level
+23 dBu
A/D Latency
0.28 mS (direct), 11 mS (AEC enabled).
Mic Pre-amp Gain
0, 11.8, 24, 44 or 54 dB switchable with ± 24 dB
trim.
A/D THD + Noise
<-94 dB, unweighted.
Mic Pre-amp EIN
<-127 dB with 150 Ohm source impedance.
Tail Length
> 250 mS
CMRR
> 76 dB @ 1 kHz, unity gain.
Convergence Time
> 100 dB/S
Mechanical Data
Items
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or
Compliance
EN 55103-1, EN 55103-2, FCC Part 15, RoHS.
Remarks
Architect and Engineer Specifications: SymNet 4 Channel AEC Input Card.
The device shall provide four acoustic echo cancellation inputs to an EDGE or RADIUS AEC frame with coarse gain, fine trim and phantom power. Up to four of these devices may be
installed in a single EDGE frame for up to sixteen channels of local input and up to one of these devices may be installed in a single RADIUS AEC for up to four channels of local input.
Levels, phantom powers, signal inversions and mutes shall be controllable via software. Audio inputs shall be accessed via rear panel 3.81 mm terminal block connectors.
Audio conversion shall be 24-bit, 48 kHz. The dynamic range shall not be lower than 115 dB, A-weighted with a maximum input level of +23 dBu.
The device shall comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The mounting plate shall be constructed of cold rolled steel, and mount into a
SymNet Radius AEC or EDGE frame I/O card slot. The device shall be a Symetrix SymNet 4 Channel AEC Input Card.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
DATA SHEET: 2 Line VoIP Interface Card
2 Line VoIP Interface Card
The 2 Line VoIP Interface Card is a SIP-based plug-in card for the Symetrix SymNet Edge and Radius AEC systems that natively integrates
with SIP-based call platforms and unified communications environments. The 2 Line VoIP Interface Card supports both narrow-band and
wideband audio capabilities and is capable of a broad range of telephony features including dialing, hold, resume, transfer, do not disturb,
and conference. Two independent SIP registrations are provided for two simultaneous independent calls per card.
The 2 Line VoIP Interface Card is designed for conferencing, paging, remote monitoring, and broadcast applications.
Best-In-Class Deployment and Administration
The 2 Line VoIP Interface Card is easy to deploy and manage in a VoIP environment. The intuitive, Web-based configuration software is
accessible from both the AV LAN or the VoIP LAN giving IT administrators and integrators easy access to configure and maintain the 2 Line
VoIP Interface.
Market-Leading, Open Standards Interoperability
Designed for enhanced interoperability, and leveraging and
complementing existing IT investments of any enterprise, the 2 Line
VoIP Interface delivers high-definition voice quality and a superior
Unified Communications experience. The 2 Line VoIP Interface is
designed on open SIP standards and has been validated with Cisco
and Asterisk SIP-compatible call management platforms.
Multiple Control Options
Symetrix’s SymNet SymVue application builder, and extensive thirdparty control support allows intuitive end-user operation and reduces
the amount of time to develop user interfaces.
Upgrade to VoIP
The 2 Line VoIP Interface Card is integrated into the call platform
environment with an easy-to-navigate Web interface and is a simple upgrade from existing PSTN solutions. With a common applications
programming interface, existing PSTN solutions can be upgraded to VoIP without reprogramming existing third-party control systems.
Benefits of the 2 Line VoIP Interface Card:
•
Natural-sounding wide-band audio for all applications improves communication and collaboration.
•
Leverages existing IT infrastructure investments to reduce telecommunications costs.
•
Web-based management access from both the VoIP LAN and AV LAN enables partners to integrate more easily into SIP call management
platforms.
•
Backwards-compatible API saves time when integrating with existing control systems.
•
Each 2 Line VoIP Interface Card can support two independent rooms, efficient for reconfigurable rooms or for cost effectively supporting
multiple rooms per Symetrix SymNet device.
•
Each line supports two callers for conferencing without an external conferencing service.
2 Line VoIP Interface Card Features and Specifications
Audio Features:
•
Codecs: G.722, G.711 (A-law and μ-Law), G.729 and G.723.1
•
DTMF tone generation (RFC 2833, SIP Info and in-band).
•
Low-delay audio packet transmission.
•
Adaptive jitter buffers.
•
Independent level adjustments for call progress, DTMF and ring tones.
•
Country-specific tone compatibility.
SymNet Composer Software Features:
•
DTMF decoding and call status logic is natively supported.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
Call Handling Features:
• 2 lines (registrations) with independent operation.
• 4 call appearances (4 remote calls, 2 per line).
• Call transfer, hold, resume.
• URI dialing.
• Call reject.
• Call timer.
• Call waiting.
• Local three-way audio conferencing per line.
• Do not disturb function.
• Local configurable digit map / dial plan.
• On-hook, off-hook, speed dialing, redial.
• Conferencing and splitting of call appearances.
•Auto-answer.
• Calling party identification.
Network, Signaling and Provisioning:
• One 10/100 Mbps LAN interface.
• Password-protected web management access via VoIP LAN or AV LAN on Symetrix SymNet Edge and Radius AEC systems.
• IETF SIP (RFC 3261 and companion RFCs).
• Conforms to IEEE802.3-2005 (Clause 40) for Physical Media Attachment.
• Conforms to IEEE802.3-2002 (Clause 28) for Link Partner Auto-Negotiation.
• Manual or dynamic host configuration protocol (DHCP) network setup.
• Network Address Translation (NAT) – support for static configuration and “Keep-Alive” SIP signaling.
• VLAN support.
• QoS Support – IEEE 802.1p/Q tagging (VLAN), and DSCP.
• RTCP support.
• Event logging.
•IPv4.
• TCP and UDP.
Specifications
Connector
RJ45.
Ethernet Cable
Standard CAT5, maximum device to device
length = 100 meters.
Ethernet Interface
10/100 Base-T.
Mechanical Data
Items
Specifications
Shipping Weight
1 lbs. (0.45 kg)
Certifications or Compliance
UL 60065, cUL 60065, IEC 60065, EN 55103-1, EN 55103-2, FCC Part 15, RoHS, WEEE.
What Ships in the Box
SymNet I/O card, card bracket, 2 black 4-40 Phillips head screws, 3 stainless steel
4-40 Phillis head screws, a quick start guide.
Remarks
Field swappable by certified technicians.
Architect and Engineer Specifications: 2 Line VoIP Interface Card.
This device shall provide two VoIP telephone lines to an EDGE or RADIUS AEC frame with standard SIP telephony functions. Up to four of these devices may be installed in a single
EDGE frame for up to eight channels of local input and up to one of these devices may be installed in a single RADIUS AEC for two channels of local input. Levels, mutes, and call
control shall be controllable via software. VoIP network connection shall be accessible via a rear panel RJ45 Ethernet connector with configuration available both via the VoIP LAN
interface and the AV LAN interface.
The device shall comply with CE and FCC Part 15 emissions limits and applicable UL/cUL safety standards. The device shall be RoHS and WEEE compliant and carry a three-year
manufacturer’s warranty. The mounting plate shall be constructed of cold rolled steel, and mount into a SymNet RADIUS AEC or EDGE frame I/O card slot. The device shall be a
Symetrix SymNet 2 Line VoIP Interface Card.
6408 216th Street SW | Mountlake Terrace, WA 98043 USA
T +1.425.778.7728 F +1.425.778.7727 | www.symetrix.co
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising