to the Instruction Manual

to the Instruction Manual
FOR YOUR PEACE OF MIND
OWNER’S MANUAL
DIGITAL VIDEO, MOVEMENT
& SOUND BABY MONITOR
Model AC1100
IMPORTANT ADVICE FOR INITIAL SETUP
DON
’T
FORG
ET
Movement Alarm
Your monitor comes with the movement alarm activated.
When switching on your monitor it will alarm, with or without
the Sensor Pad plugged in, if no movement is detected.
Deactivate the movement function to use the monitor without
the Sensor Pad.
Batteries
Insert the enclosed rechargeable batteries into the Parent
Unit. If inserted incorrectly the Parent Unit will not charge
when placed in the charging cradle. The battery icon will flash
briefly on the Parent Unit screen to indicate charging.
Cord Safety
Ensure the Nursery Unit is at least 1 metre away from your
baby’s cot. The Sensor Pad cord must always be kept out of
reach of baby and secured using the cord cover kit provided.
PLEASE FOLLOW THE INSTRUCTIONS CAREFULLY FOR CORRECT SETUP
Please DO NOT return this product to the store. For assistance please
contact our helpline on 0345 009 1789 or email helpline@babyhelpline.co.uk
Mon – Fri 10am – 4pm, excluding bank holidays.
TABLE OF CONTENTS
WARNINGS................................................................................... 3
AC1100 SETUP REQUIREMENTS................................................... 8
STEP 1 - Charging the Parent Unit................................................ 9
STEP 2 - Installing the Sensor Pad............................................. 10
STEP 3 - Setting up the Nursery Unit.........................................13
STEP 4 - Turning on your Monitor...............................................14
STEP 5 - Testing and getting to know your Monitor.............15
STEP 6 - A
ctivating and deactivating
additional functions........................................................19
Troubleshooting................................................................................ 25
Limited warranty............................................................................... 27
Technical specifications..................................................................28
OWNER’S MANUAL
KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE.
PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE
ASSEMBLING & USING THE PRODUCT.
FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH OR DAMAGES TO THE PRODUCT.
THE SENSOR PAD FEATURE IS NOT FOR USE WITH ADULTS, CHILDREN OR INFANTS
OLDER THAN 24 MONTHS.
THE SENSOR PAD IS NOT INTENDED TO BE USED TO DETERMINE IF A CHILD IS OUT
OF THE CRIB.
WARNING
Adult assembly required.
Keep small parts away from children when assembling.
This Angelcare Monitor is a Personal Care Product. Please DO NOT return this to the store
where you purchased it from. If you have any questions or require assistance please call the
Angelcare Helpline on 0345 009 1789 or email helpline@babyhelpline.co.uk.
The Baby Helpline is open Monday to Friday, 10am to 4pm. The helpline is closed on bank
holidays.
For additional FAQs and to download instruction manuals visit; www.angelcare.co.uk.
To order spare parts for your Angelcare Baby Monitor visit; www.megababy.co.uk.
2
UK1014
WARNINGS
1. THIS PRODUC T CANNOT REPL ACE
RESPONSIBLE ADULT SUPERVISION. This
product is designed to aid in the monitoring
of your child. When using the monitor, you
must still provide the supervision necessary
for the continued safety of your child.
Monitoring of premature babies, or those
considered to be at risk, should always
be carried out under the supervision of a
health professional. This monitor SHOULD
NOT be used as a medical device, nor as
a device to prevent Sudden Infant Death
Syndrome (SIDS).
2. WARNING Strangulation Hazard —
Children have STRANGLED in cords. Keep
adapter cords out of
the reach of children
(more than 1 m away).
NEVER use Sensor
Pad(s) without the
protective
cord
covering.
Check
protective
cord
covering before each
use. Immediately discontinue use of Sensor
Pad(s) if protective covering is damaged
or broken.
3. Never use extension cords with AC
adapters. ONLY use the AC adapters
provided.
4. When an AC Adapter is plugged into
an electrical outlet, DO NOT touch the
exposed end.
5. ALWAYS be sure that both the transmitter
and receiver are working properly and are
within range of each other. Test monitor
before first use, periodically and when
changing location of the Nursery Unit.
6. ALWAYS be sure to immediately check
on baby whenever an alarm sounds.
7. DO NOT use monitor near water (such
as bath tub, sink, etc.).
CAUTION
8. Keep monitor AWAY from heat sources
(such as stoves, radiators, etc.).
9. ALWAYS place both the Nursery Unit and
Parent Unit on a flat surface in an upright
position and allow for proper ventilation.
DO NOT place on sofas, cushions, beds,
etc. which may block ventilation.
10. This monitor uses public airwaves to
transmit signals. The Parent Unit may
pick up signals or inter ference from
other nursery monitors in your area. Your
monitor may even be picked up by other
households. To protect your privacy, make
sure both units are turned OFF when not in
use. If you experience interference, change
the channel on both units.
11. This product is NOT a toy. DO NOT allow
children to play with it.
12. This product contains small parts. Adult
assembly required. Exercise care when
unpacking and assembling the product
and keep small parts away from children.
13. When using the monitor, the room
temperature should be between 50°F
(10°C) and 104°F (40°C).
BATTERY WARNING
14. Use O N LY A A A R EC HARG E AB LE
batteries for the Parent Unit. DO NOT
mix old and new batteries . DO NOT
mix alkaline, standard or rechargeable
batteries. Insert batteries with correct
polarity. DO NOT short-circuit supply
terminals. ONLY use the recommended
batteries or equivalent (volts and size)
and the correct adapter. Remove batteries
when product is stored for long periods
of time or when batteries are exhausted.
Dispose exhausted batteries properly. DO
NOT recharge non-rechargeable batteries.
Rechargeable batteries are ONLY to be
charged under adult supervision. Keep all
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT EXPOSE TO RAIN OR MOISTURE
3
15.2 Keep these instructions. The safety
and operating instructions should be
retained for future reference.
15.10 Accessories - Only use attachments/
accessories specified by the manufacturer.
DO NOT place this product on an unstable
cart, stand, tripod, bracket or table. The
product may fall, causing serious injury
to a child or adult and serious damage to
the product. Use ONLY with a cart, stand,
tripod, bracket or table recommended by
the manufacturer or sold with the product.
Any mounting of the product should follow
the manufacturer’s instructions.
15.3 Heed all warnings – All warnings on the
product and in the operating instructions
should be adhered to.
15.11 Unplug this appliance during lightning
storms or when not used for long periods
of time.
15.4 Follow all instructions – All operating
and use instructions should be followed.
15.12 Ser vicing - DO NOT attempt to
service this product yourself as opening
or removing covers (except battery doors)
may expose you to dangerous voltage or
other hazards.
batteries away from children.
15. IMPORTANT SAFETY INSTRUCTIONS
15.1 Read these instructions - All the safety
instructions should be read before the
product is operated.
15.5 Water and moisture - DO NOT use
this apparatus near water. For example,
near a bath tub, wash bowl, kitchen sink,
laundry tub, in a wet environment or near
a swimming pool and the like. Care should
be taken so that objects DO NOT fall onto
units and that liquids are not spilled into
either unit or Sensor Pad through its
openings.
15.6 Cleaning - Disconnect all units before
cleaning. DO NOT immerse in water any
part of the Nursery Unit, Parent Unit. Clean
only with dry cloth.
15.7 Ventilation - DO NOT block any
ventilation openings. Allow for proper
ventilation when units are in use. DO NOT
cover the Nursery Unit or Parent Unit with
any object such as a blanket. DO NOT place
it in a drawer or in any location which
would muffle the sound or interfere with
the normal flow of air.
15.8 Heat sources - DO NOT install near
any heat sources such as radiators, heat
registers, stoves, TVs or other apparatus
(including amplifiers) that produce heat.
Heat can damage the case or electrical
parts.
15.9 Power cord protection - Protect the
Sensor Pad cord and Adapter’s power
cord from being walked on or pinched by
furniture or other items – Power supply
cords should be routed so that they are not
likely to be walked on or pinched by items
upon or against them, paying particular
attention to cords and plugs, convenience
receptacle, and the point where they exit
from the product.
4
15.13 R e p l a c e m e n t p a r t s - W h e n
replacement parts are required, be sure
the replacement parts specified by the
manufacturer have the same characteristic
a s th e o r i g i n a l p a r t . U n a u th o r ize d
substitution may result in fire, electric
shock or other hazards.
15.14 U s a g e - This b a by m o nito r is
intended as an aid. It is NOT a substitute for
responsible and proper adult supervision
and should not be used as such. Use this
appliance ONLY for its intended use as
described in this manual.
15.15 Powe r S o u rce s - O p e rate th is
product only from the type of power
source indicated on the type plate of the
adaptor. If you are unsure of the type of
power supply to your home, consult your
dealer or local power company.
15.16 Overloading - DO NOT overload
wall outlets, extension cords or integral
convenience receptacles as this can result
in a risk of fire or electric shock.
15.17 Object and Liquid Entry - NEVER
push objects of any kind into this product
through casing slots as they may touch
dangerous voltage points or short out
parts that could result in a risk of fire or
electric shock. NEVER spill liquid of any
kind on the product.
15.18 Antenna - The antenna used for this
transmitter must be installed to provide
a separation distance of at least 20 cm
(7.9”) from all persons and must not be
collocated or operating in conjunction with
any other antenna or transmitter.
15.19 Power Lines - An outside antenna
system should NOT be located in the
vicinity of overhead power lines or other
electric light or power circuit, or where it
can fall into such power lines or circuits as
contact with them may be fatal.
15.20 WARNING Strangulation Hazard —
Children have STRANGLED in cords. Keep
adapter cords out of
the reach of children
(more than 1 m away).
NEVER use Sensor
Pad(s) without the
protective
cord
covering.
Check
protective
cord
covering before each
use. Immediately discontinue use of Sensor
Pad(s) if protective covering is damaged
or broken.
The sensitivity level may also need to be
adjusted. Refer to step 5.1.
15.23 Sensor Pad - Your Sensor Pad can
be used in any crib that is stationary. If
the crib has a spring or slat base, place a
hard board between the crib base and the
Sensor Pad measuring at least 13” x 13”
(33 x 33 cm) and 1/4 inch (6 mm) thick.
Only use your Angelcare ® monitor in a
stationary sleeping environment such as
a crib where the Sensor Pad can rest on
a completely flat, firm surface.
15.24 The Sensor Pad is made of plastic
and does not permit the air to circulate.
Therefore, mildew build up could develop
underneath the mattress in the sensor pad
area. We suggest rotating the mattress
regularly to prevent any mildew.
15.21 Interference - This monitor uses public
airwaves to transmit signals. The Parent
Unit may pick up signals or interference
from other nursery monitors in your area.
Your monitor may even be picked up by
other households. To protect your privacy,
make sure both units are turned OFF when
not in use. If you experience interference,
change the channel on both units.
15.22 Vibration Source - When the monitor
is in use, DO NOT use a crib mobile or
other crib accessories that may produce
vibrations. Other sources of vibrations
may include fans, washing machines, loud
music, etc. These sources of vibration may
interfere with the performance of your
Angelcare ® monitor and the alarm will
not sound if it continues to detect any
movement other than your baby’s. Be sure
all vibration sources are eliminated before
using the monitor.
You may experience false alarms for several
reasons. The most common reason is the
Nursery Unit has not been turned OFF after
you have removed your baby from the crib.
Another reason is the Sensor Pad has not
been placed under the mattress properly.
Be sure the Sensor Pad is on a flat, firm
surface with the printed side facing up.
5
16. IMPORTANT SAFETY INSTRUCTIONS
RELATED TO USE OF BATTERIES
16.1 Use O N LY the t ype and size of
batteries specified in the owner’s manual.
There is a risk of explosion if batteries are
replaced with an incorrect type.
16.2 U s e O N LY A A A r e c h a r g e a b l e
batteries and/or the AC Adapters provided
for the Parent Unit. You must use only
rechargeable batteries in the Parent Unit.
DO NOT use alkaline batteries or you will
severely damage the unit.
16.3 Charge the batteries for 15 hours prior
to first use. Be sure to have the monitor in
the OFF position during this period. ONLY
use the AC Adapters included with your
monitor.
16.10 DO NOT attempt to rejuvenate the
batteries provided with or identified for
use with this product by heating them.
Sudden release of battery electrolyte may
occur, causing burns or irritation to eyes
or skin.
16.4 DO NOT use these adapters with any
other equipments.
16.11 If and when necessary, the batteries
must be replaced with identical new ones
or equivalent (volts and size). If a battery
to be replaced is connected with other
batteries in series, replace the other
batteries at the same time as well. DO
NOT mix old and new batteries.
16.5 When unplugging the AC Adapter
from the Nurser y Unit, be sure it is
switched to the OFF position. If it isn’t, the
unit will revert to battery mode if batteries
are installed.
16.12 Reverse polarity installation of the
batteries in the end product must be
avoided. Reverse insertion of batteries
can cause charging, and that may result
in leakage or explosion.
16.6 DO NOT use rechargeable batteries
in the Nursery Unit. Use alkaline batteries
ONLY.
16.13 Remove batteries from this product
if you store the product over 30 days
because the batteries could leak and
damage the product.
16.7 DO NOT dispose batteries in fire. They
may explode. Check with local regulations
for possible special disposal instructions.
16.8 Exercise care in handling batteries
in order not to short out the batteries
with conducting materials such as rings,
bracelets and keys. Overcharging, short
circuiting, reverse charging, mutilation, or
incineration of batteries must be avoided
to prevent one or more of the following
occurrences: release of toxic materials,
release of hydrogen and/or oxygen gas,
rise in surface temperature.
6
16.9 DO NOT attempt to recharge batteries
provided with or identified for use with
this product that are not intended to be
charged. The batteries may leak corrosive
electrolyte or explode.
16.14 Discard ‘dead’ batteries as soon as
possible since ‘dead’ batteries are more
likely to leak in a product. If a battery has
leaked or vented, it should be replaced
immediately using protective gloves.
16.15 DO NOT store this product, or the
batteries provided with or identified for
use with this product, in high-temperature
areas.
WARNING
(North America Only)
17.1 Modifications not authorized by the
manufacturer may void users authority to
operate this device.
17.2 NOTE: This equipment has been tested
and found to comply with part 15 of the
FCC Rules and the Industry Canada licenceexempt RSS standard(s). These limits are
designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy
and, if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
17.4 This device complies with the part 15
of the FCC Rules and the Industry Canada
licence - exempt RSS standards(s). Operation
is subject to the following two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
17.3 However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment OFF and ON, the
user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
FCC AND IC REGULATIONS
RF radiation exposure statement
The Nursery Unit complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. Caution: To maintain the compliance with the FCC’s RF exposure guideline,
install the Nursery Unit at least 20 cm from ALL persons. The transmitter of this device must
not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada
This product meets the applicable Industry Canada technical specifications.
CAN ICES-3 (B)/NMB-3 (B)
7
VIDEO, MOVEMENT
SETUP REQUIREMENTS
& SOUND MONITOR
Model AC1100
INCLUDED:
Rechargeable
Parent Unit
6
5
Nursery Unit
3
4
2
Charging Cradle
1
2X
1 Sensor Pad (AC1100) or 2 Sensor Pads (AC1100-2SP)
with pre-installed cord covers
2 AC Adapters
3X
3 Rechargeable
AAA Batteries
WHAT YOU WILL NEED (NOT INCLUDED):
YOU MUST PREPARE:
One hardboard (not included)
Thickness: 6 mm
Minimum dimensions:
33 cm x 33 cm
Maximum dimensions:
equal to the mattress size
3X
Hardboard
IMPORTANT
The hardboard must be larger than
the Sensor Pad surface area.
BABY’S ROOM:
Belt Clip
3 AAA Alkaline
Batteries
Miniature Philips
Screwdriver
IMPORTANT
Place the crib near a supporting wall and far from air currents. Install the Nursery
Unit on a flat, stable surface facing the crib at a distance of at least 1 meter.
Make sure to plug the adapter to the socket outlet nearest to the equipment
and that it is easily accessible.
IMPORTANT
Keep
at least
1 m.
6
5
8
Sensor Pad
4
3
2
1
STEP 1 - CHARGING THE PARENT UNIT
1
IMPORTANT
Never use regular
alkaline batteries
in the Parent Unit;
they may explode.
2
1) Remove the Belt Clip.
3
4
2) Remove the battery door and insert
the Rechargeable Batteries (included).
10h
15
3) Connect the AC Adapter to the
Charging Cradle and
into an electrical outlet.
4) Charge the unit for 10 continuous
hours (prior to first use).
NOTE:
To optimize your battery performance
please refer to Battery Guidelines in the
Trouble Shooting section.
PARENT UNIT:
A)LCD Touchscreen
F
A
B)POWER ON/OFF
C)Microphone
B
G
D)Speaker
E)Charging Cradle
H
F)Belt Clip
G)Speaker
Volume Buttons
C
I
D
H)Talk Back Button
I) Battery Door
E
Front Side
J
J) AC Adapter Outlet
(not shown)
Left Side
9
STEP 2 - INSTALLING THE SENSOR PAD
6
5
3
4
2
1
Cord covers 1, 2, 3, 4:
Position on floor
Cord cover 4:
Contains double sided
tape to securely install
beneath crib leg
Cord cover 5:
Position vertically
between mattress
support and floor
Sensor Pad with pre-installed cord covers
Cord cover 6:
Place under
the mattress
WARNING
STRANGULATION HAZARD.
Children have STRANGLED in cords:
•Keep adapter cords out of the reach of children
(more than 1 m away).
•Because of the serious strangulation risk to infants
and toddlers, parents and caregivers should never
place the Nursery Unit within 1 meter of a crib.
•NEVER use Sensor Pad without the cord covers.
Check cord covers before each use to ensure it is
securely placed under the leg of the crib. Discontinue
use of Sensor Pad if any cord covers are damaged or
broken.
•NEVER use extension cords with AC adapters. ONLY
use the AC adapters provided. This product is not a
toy. Never allow children to play with it.
2.1 - SELECT A LOCATION FOR THE NURSERY UNIT
Select a location for the Nursery Unit that is
at least 1 meter away from the crib.
IMPORTANT
Keep
at least
1 m.
6
5
10
4
3
2
1
2.2 - SELECT THE CRIB LEG YOU WILL BE USING TO SECURE THE CORD COVERS
RECOMMENDED
1) Use the crib leg by the wall closest to
the Nursery Unit (fig 1). In cases where
the Nursery Unit is across the room, use
the leg closest to the Nursery Unit to
position the covered wire (fig 2). It is
always preferable that the covered cord
run along a wall.
6
5
4
3
2
Fig 1
1
OR
6
1
2
5
4
3
Fig 2
2.3 - INSTALL THE SENSOR PAD ON THE MATTRESS SUPPORT
3
1) Remove the mattress from the crib.
6
5
2) Place the Sensor Pad - printed side up
- on top of the hardboard at the center
of the crib.
4
3
2
1
3) Run the connection pin, warning label
and the first 5 cord covers down along
the backside of the crib leg, between
the mattress support and the inside
edge of the crib.
4) Bring the first 4 cord covers down
the floor, and keep the 5th cord cover
vertically, along the backside of the crib
leg, (between the mattress and the
inside edge of the crib).
4
5
5) Remove any cord slack to make sure
no parts of the cord are loose.
5
11
6
8 cm
6
6) Place the 6th cord cover approximately
8 cm from the edge of the mattress
support.
7) Snap together the remaining cord
covers that will run along the floor.
7
8) Remove any cord slack to make sure
no parts of the cord are loose.
CLIC!
4
3
2
1
9) Peel off the double-sided tape on the
4th cord cover and place it securely
under the crib leg.
10)Install the Nursery Unit on a flat, stable
surface facing the crib at a distance of
at least 1 m and plug the Sensor Pad
cord into the Nursery Unit.
8
9
11) Check to make sure the Sensor Pad has
not moved from position.
12)Place the mattress back inside the crib.
4
3
2
1
The Sensor Pad functions with any size
and type of mattress except memory-foam
mattresses and hollow frame mattresses.
10
The hardboard maintains a constant
pressure on the Sensor Pad, enabling it to
detect the baby’s movements even when
the baby is at the edges of the crib.
WARNING
STRANGULATION HAZARD
• Remove all slack from Sensor Pad Cord.
• When lowering the mattress support
as your child grows, slide the vertical
Cord Cover (5) upward so it remains
approximately in the center between
the mattress support and the floor. Slide
the Sensor Pad Cord through the Floor
Cover to eliminate any additional slack.
12
• The Sensor Pad is not designed for use
with adults, children or infants older
than 24 months.
• Discontinue used of the Sensor Pad
when child is older than 24 months.
Remove sensor pad from crib and store
for future use.
• BEFORE FIRST TIME USE: To test
that the unit is ready for use, refer to
instruction manual on how to test that
the installation has been done
STEP 3 - SETTING UP THE NURSERY UNIT
1) Remove the battery door and insert
3 AAA Alkaline Batteries (not included).
1
2) Place the Nursery Unit at a minimum
of 1 m away from the crib.
3) Connect the AC Adapter to the Nursery
Unit and into an electrical outlet.
4) Direct the angle of the camera toward
the crib using the rotating dial.
NOTE:
2
IMPORTANT
Keep at least
1m
6
5
4
3
2
The batteries maintain power
supply in case of power outage.
3
1
4
NURSERY UNIT:
A)Night Light
B)Main Button
C)POWER ON/OFF
(Left ‘Wing’)
A
D)Night Light ON/OFF
(Right ‘Wing’)
E)Video Camera
B
C
F)4 Infrared LEDs
(Night Vision Camera)
D
E
F
G
I
G)Power Indicator (green)
Low Battery Indicator (red)
J
H)Microphone
I) Speaker
K
J) Sensor Pad Outlet
H
L
K)AC Adapter Outlet
L) Roating Dial
for Camera Angle
M
Front Side
Back Side
* Nursery Unit may be installed on a tripod (not included).
N
M)Battery Door
(not shown)
N)Tripod Outlet*
(not shown)
13
STEP 4 - TURNING ON YOUR MONITOR
1) Press the Parent Unit ON/OFF button
for 2 seconds until blue screen appears.
2
1
3
2) The Parent Unit will display
Video mode screen.
3) Press the Menu icon to access
main menu.
4) The Parent Unit will display
Menu mode. 4
5
5) Push and hold the Nursery Unit left
‘wing’ button for 2 seconds.
OK
If there is a lost connection
between the 2 units (refer to
troubleshooting):
When Parent Unit is turned ON and
Nursery Unit is OFF, Parent Unit will
display Disconnected Mode and will
turn itself OFF after 60 seconds.
• The Out-of-Range icon will
appear on the screen.
• The Lost Connection icon will
appear on the indicator bar.
INDICATION BAR IMPORTANT ICONS
Temperature icon:
Indicates room temperature
Temperature Alarm icon: Indicates
Temperature Alarm is active
Connection icon: Indicates the
connection quality between the
Parent Unit and Nursery Unit.
Good connection
Poor connection
Sound icon: Indicates that Sound
function is active
Lost connection
Alarm icon: Indicates selected
alarm mode
Out-of-Range
Sound alarm
Battery Level icon:
Indicates battery level
Sound alarm
and vibration
Empty
Vibration only
Pendulum icon: Indicates the
Motion Sensor is active
1/3 Full
2/3 Full
Full
14
STEP 5 - TESTING AND GETTING TO KNOW YOUR MONITOR
The Angelcare® monitor can be used with the pre-program factory settings or you can
also customise your settings to your preference.
OK
All changes and
adjustments made
in the main menu and
sub-menus will not be
activated unless you
confirm them by pressing
the OK icon.
IMPORTANT
When in menu or sub-menu modes,
sound transmission between Parent
and Nursery Units will be temporarily
deactivated. ONLY movementdetection alarm will remain active (if
function is activated).
5.1 - SENSOR PAD
TO ACTIVATE THE SENSOR PAD:
1
2
1) Press Menu icon to access
main menu.
2) Press Movement icon to activate
or deactivate Movement Alarm.
ON
OFF
OK
3) Press OK icon to confirm. TO TEST THE SENSOR PAD:
1) Move your hand lightly on the mattress.
1
2
The pendulum icon will appear
on Parent Unit indicator bar.
It will move as you move your
hand and trigger a ‘TIC’ sound.
2) Remove your hand from the mattress.
After 15 seconds you will hear a
‘TIC’ pre-alarm sound, and 5 seconds
later the Movement Alarm will trigger.
MOTION ALARM
• Alarm activates when no movement is detected by Sensor Pad for 20 seconds.
• Both the Parent Unit and Nursery Unit speakers will emit loud warning sound.
• Motion Alarm icon will show on the LCD screen.
IF THE ALARM DOES NOT SOUND
•
•
•
•
Avoid contact with crib while Sensor Pad is in operation.
Place crib near a supporting wall.
Turn OFF crib mobile, fans, loud music or anything else that may cause vibration.
Adjust Sensor Pad sensitivity level.
15
TO STOP THE ALARM
Press the Nursery
Unit’s Main button
Press the Parent
Unit Motion
Alarm icon
OR
Hold down left ‘wing’
button for two seconds
to turn OFF the Unit
TO ADJUST THE SENSOR PAD SENSITIVITY LEVEL:
1
3
2
1) Press Menu icon to access
main menu.
OFF
ON
2) Press settings icon
to access sub-menu.
ON
OK
3) Press movement sensitivity icon to choose
the desired sensitivity level (1 to 5). OK
NOTE:
If you are receiving false alarms,
adjust the sensitivity level.
4) Press OK icon to confirm.
TO ACTIVATE THE TIC FUNCTION:
Allows you to hear a TIC sound when Sensor Pad function is activated.
2
1) Press Menu icon to access
1
the main menu.
2) Press TIC icon to activate or deactivate
the tic function.
OK
Regular TIC sound will emit from Parent Unit
and a moving pendulum will appear
on Parent Unit indicator bar
ON
OFF
3) Press OK icon to confirm. IMPORTANT
• The Sensor Pad is not designed for use with adults, children or infants older
than 24 months.
• Once you are finished using the Sensor Pad, please remove it from the baby’s
crib and store it away.
16
5.2 - SOUND
1) Press Menu icon to access
main menu.
TO ACTIVATE SOUND:
1
2) Press sound icon to activate
or deactivate sound.
2
ON
OFF
OK
3) Press OK icon to confirm.
TO TEST SOUND:
Ask someone to speak into the Nursery
Unit or place the unit near a radio to ensure
that sound is being picked up.
IMPORTANT
To avoid feedback (whistling), keep
both units at least 3 m apart.
ADJUST SOUND LEVEL
IF YOU HEAR NO SOUND:
• Check that both units are powered on.
• Check that both units are plugged
into functioning electrical outlets.
• Check the batteries in both units
(replace or recharge them if necessary).
• Bring Parent Unit closer to Nursery Unit.
PUT IN SILENT/MUTE MODE
Raise volume (+)
PUT IN DIALOGUE MODE
Press the (-)
button for 2
seconds to
mute sound.
Lower volume (-)
Press and hold
talk button to
speak to baby.
5.3 - BATTERIES
HOW TO CHECK THE BATTERIES:
Unplug the Adapters from both units.
• If the green light on the Nursery Unit does not show, replace the batteries.
• If the Parent Unit and its screen do not light up, recharge the batteries.
HOW TO CHARGE THE BATTERIES IN THE PARENT UNIT:
Leave the Parent Unit in the Charging Cradle
to fully charge the unit. Although the batteries
at 1/3 capacity works normally, we recommend
that you fully recharge them.
1/3 full
2/3 full
full
PARENT UNIT BATTERY ALARM
• Alarm activates when the batteries need to be recharged.
• Parent Unit will emit a beep sound every 15 seconds.
• Battery Alarm icon will show on LCD screen.
17
YOU ARE NOW READY
TO USE YOUR MONITOR
The Angelcare® monitor can be used with the pre-program factory settings
or you can also customise your settings to your preference.
DEFAULT SETTINGS
Continuous Sound: ON
Speaker Volume: Level 3 (of 6)
Movement Mode: ON
Sensor Pad Sensitivity: Level 3 (of 5)
TIC: OFF
Temperature Alarm: OFF
Temperature Alarm Settings:
High Temperature Limit: 32˚
Low Temperature Limit: 5˚
VOX Mode: OFF
Alarm Mode: Sound alarm only
Video Camera: ON
IMPORTANT
• Test your monitor before first use.
• Test your monitor regularly to ensure it is functioning correctly.
• Test your monitor every time you move the Sensor Pad to a different place.
18
STEP 6 - ACTIVATING AND DEACTIVATING ADDITIONAL FUNCTIONS
IMPORTANT
When in the menu or sub-menu
modes, sound transmission between
Parent and Nursery Units will be
temporarily deactivated. ONLY the
motion-detection alarm will remain
active (if function is activated).
All changes and
adjustments made
in the main menu and
sub-menus will not be
activated unless you
confirm them by
pressing the OK icon.
OK
6.1 - VOICE ACTIVATION (VOX) OR CONTINUOUS SOUND MODE
Allows you to select your option on how you monitor sound:
VOX (voice activation picks up sound based on the setting of the sensitivity level) or
Continuous (sound monitoring is continuously on, picking up all sounds).
TO ACTIVATE VOX MODE:
1
3
2
1) Press Menu icon to access
the main menu.
OFF
ON
2) Press settings icon
to access sub-menu.
ON
OK
ON
3) Press the VOX icon to activate
or deactivate the VOX function.
OK
NOTE:
OFF
VOX ON
(VOX)
VOX OFF
(Continuous)
By deactivating VOX the Continuous
setting is ON.
4) Press OK to confirm.
TO ADJUST THE VOX SENSITIVITY:
Allows you to determine the sound level needed to trigger sound transmission
to the Parent Unit.
1
3
2
1) Press Menu icon to access
the main menu.
OFF
2) Press settings icon
to access sub-menu.
ON
ON
OK
OK
3) Press VOX icon sensitivity to choose
sound sensitivity level (1 to 4).
4) Press OK to confirm.
19
6.2 - ALARM
Allows you to select your preferred alarm mode for the Parent Unit.
1
3
2
1) Press the Menu icon to access
main menu.
OFF
2) Press the settings icon
to access sub-menu.
ON
ON
OK
OK
3) Press the Alarm icon to change
the alarm mode.
4) Press OK to confirm.
Sound alarm only
Alarm Mode icon
shows in the top bar
of the Parent Unit.
Sound alarm
and vibration
Sound alarm will replace vibration mode when
the Parent Unit is in its Charging Cradle.
Vibration only (the alarm will
not sound on Parent Unit but
it will on Nursery Unit).
When the battery capacity is low, the
vibration will be temporary deactivated. It will
reactivate when the battery is fully recharged.
IMPORTANT
When in setting mode no sound or alarms will transmit to the Parent Unit, except
the movement alarm (if this function was already activated).
6.3 - HOLD
Allows you to put your Angelcare Monitor on HOLD.
1) Press the Menu icon to access
main menu.
1
2
2
OK
2) Press the Hold icon
OR
Press and hold the Nursery Unit
Main button for at least 2 seconds.
3) Hold icon will appear on the screen.
Nursery Unit Night Light will blink.
Parent Unit will emit 3 consecutive
beeps every 30 seconds to remind
you that monitor is on hold.
4) Press the Hold icon or Nursery Unit
Main button again to return
to normal operation.
IMPORTANT
When your monitor is on hold, the motion-detection feature and motion alarm
are disabled.
20
6.4 - THERMOMETER
TO CHANGE THE MEASUREMENT UNIT:
1
3
2
o
30 C
+
o
15 C
o
ON
C
ºC
ºF
OK
OK
1) Press the Menu icon to access
main menu.
2) Press the temperature icon to access
sub-menu.
3) Press the ˚C ˚F icon to change from
Celsius to Fahrenheit.
4) Press OK to confirm.
o
o
C
ºC
ºF
Celsius
F
ºC
ºF
Fahrenheit
TO ACTIVATE THE TEMPERATURE ALARM:
1
3
2
1) Press the Menu icon to access
main menu.
o
30 C
+
o
2) Press the temperature icon to access
sub-menu.
15 C
o
ºC
ºF
OK
ON
C
OK
3) Press the Temperature Alarm icon
to activate or deactivate
temperature alarm.
4) Press OK icon to confirm.
ON
OFF
ON
Temperature Alarm icon:
Indicates temperature alarm
is active.
OFF
TO SET THE TEMPERATURE RANGE:
1
1) Press the Menu icon to access
main menu.
2
o
30 C
3
+
2) Press the temperature icon to access
sub-menu.
o
15 C
4
o
OK
ON
C
ºC
ºF
OK
The range between the minimum and maximum
temperature must be at least 4 ˚C/7 ˚F. An error
tone will be heard if you try to set it up below
this minimum level.
3) Press (+ or -) to set maximum
temperature range (15 to 32 ˚Celsius
/59 to 90 ˚Fahrenheit).
4) Press (+ or -) to set minimum
temperature range (5 to 20 ˚Celsius
/41 to 68 ˚Fahrenheit).
5) Press OK icon to confirm.
TEMPERATURE ALARM
• Alarm activates when temperature rearches maximum or minimum set temperature.
• Parent Unit will emit 4 consecutive beeps, every 5 seconds.
• Temperature Alarm icon will show on LCD screen.
21
6.5 - VIDEO
Allows you to turn video function ON or OFF.
1
1) Press the Menu icon to access
main menu.
4
2
2) Press the Video icon to activate
or deactivate the video function.
3
3) Press OK to confirm.
OFF
OK
4) Press the Menu icon to return
to main menu.
ON
OFF
6.6 - SCREEN SAVER
Allows you to set the screen saver starting point.
1
2
1) Press the Menu icon to access
main menu.
OFF
3
2) Press settings icon
to access sub-menu.
ON
ON
OK
OK
OFF/5/10/15/20 sec
3) Press the Screen Saver icon to select
the delay before video mode turn
into screen saver mode.
4) Press OK to confirm.
NOTE:
Screen Saver icon will appear
when video is in Screen Saver mode.
MANUAL SETTING:
To trigger manually the screen saver mode push the Parent Unit Power button.
Do not push it for more than 2 seconds since this will shut down the Parent Unit.
TO REVERT BACK TO CAMERA CAPTION
Press the screen
22
6.7 - INFRARED NIGHT VISION
Allows you to capture image when lighting is unsufficient.
TO ACTIVATE NIGHT VISION:
Press the Night Vision icon to chose available modes:
AUTO: The infrared LEDS will turn on automatically
when the lighting is not sufficient. The image
transition takes 20 seconds
ON: The infrared LEDS are ON at all times.
OFF: The infrared LEDS are OFF at all times.
There are 4 built-in infrared LEDs
on the Nursery Unit to enable clear
black and white image. The image
transition takes 20 seconds.
The Moon icon will appear
when the infrared LEDS are ON.
6.8 - NIGHT LIGHT
Allows you to use your monitor as a night light.
TO ACTIVATE THE LIGHT:
Push right ‘wing’ of Nursery Unit to the night light
ON or OFF.
6.9 - PAGER
Allows you to locate the Parent Unit.
TO LOCATE PARENT UNIT:
Press Nursery Unit main button for less
than 2 seconds. The Parent Unit will emit
a paging sound for one minute.
IMPORTANT
If you press the Main
Button for more than 2
seconds, you will put the
movement monitoring on
Hold. To Unhold, push the
button again.
TO STOP THE PAGING SOUND:
Press the Parent
Unit screen
OR
Press the Nursery Unit’s
main button
23
6.10 - ZOOM MODE
Allows you to zoom in to twice the normal view.
1
2
1) Press the zoom icon.
2) Press the directional arrows to zoom in
on what you want to see more closely.
3) Press the zoom icon again to return
3
to normal view. 6.11 - MUTE
Allows you to put your monitor in Silent/Mute mode
TO PUT ON MUTE:
Press the (-) button and hold
for 2 seconds to mute sound.
TO UNMUTE:
NOTE:
Press the (-) button again and hold
for 2 seconds to unmute sound.
On the Parent Unit,
the Mute ICON will blink.
6.12 - KEY TONE
Allows you to activated or deactivate key tone sound.
1
3
2
1) Press the Menu icon to access
main menu.
OFF
2) Press the settings icon
to access sub-menu.
ON
ON
OK
ON
OK
4) Press OK icon to confirm.
OFF
ON
3) Press icon to activate or deactivate
key tone sound.
OFF
6.13 - TIMER
Attain activities.
1
1) Press Menu icon to access
main menu.
3
2
2) Press Timer icon
to start or stop the timer.
OK
ON
24
0:00
OFF
3) View Timer in video mode.
(shows in minutes only).
• Stops automatically after 5 hrs 59 min.
• Stops automatically if the Parent Unit
is turned OFF.
TROUBLESHOOTING
TAKING CARE OF YOUR RECHARGEABLE BATTERIES
• Ensure that you fully charge your batteries for 10 hrs before their first use.
• To maintain maximum battery life it is recommended that you fully discharge your
batteries periodically. Battery performance can be diminished by leaving the batteries
constantly charging on the charging cradle. If your Parent Unit is no in use, please turn
it off.
• Inadequate battery power can impair the performance of your monitor. If you are
not happy with the performance of your Parent Unit/Monitor, please replace the
rechargeable batteries (3 x NIMH Rechargeable batteries).
• It is advisable to change the batteries every 6 months.
FALSE ALARMS
• Turn OFF the Nursery Unit.
• Verify the connection between Sensor Pad and Nursery Unit. Unplug and reconnect
the cord.
• Make sure there is no bedding between mattress and Sensor Pad.
• If the crib has a spring or slat base, place a hardboard between the crib base and the
Sensor Pad measuring at least 33 x 33 cm and 6 mm thick.
• Make sure Sensor Pad is positioned as described under the setup requirements.
Sensitivity may need to be adjusted, refer to step 5.1.
ALARM WILL NOT SOUND
• Avoid contact with the crib when the monitor is ON.
• Place crib near a solid supporting wall to avoid Sensor Pad from detecting movement
from outside the crib.
• You may need to decrease the sensitivity, refer to step 5.1.
NO SOUND IS BEING TRANSMITTED
•
•
•
•
•
•
Bring Parent Unit closer to Nursery Unit.
Check/replace batteries or recharge Parent Unit.
Check connections or change to another electrical outlet.
Ensure both units are ON.
Ensure mains supply units are activated.
Check on the top bar of the Parent Unit to see if the Monitor is on “MUTE” instead
of “ON”. Refer to step 6.11.
NURSERY UNIT POWER ON INDICATOR (GREEN LIGHT) DOES NOT LIGHT UP
• Check connections or change to another electrical outlet.
• Push and hold the left ‘wing’ for 2 seconds to turn the Nursery Unit ON.
WEAK RECEPTION
•
•
•
•
Bring units closer together.
Change the position of one or both units.
Place units on a flat surface away from baby’s reach.
Replace the batteries or recharge Parent Unit.
25
STATIC, DISTORTION, INTERFERENCES
(FROM OTHER MONITORS, WIRELESS PHONES, WALKIE-TALKIES, ETC...)
• Rotate Parent Unit or move it away from source of interference.
FEEDBACK (LOUD NOISES EMITTED FROM THE PARENT UNIT)
• Move units farther apart (at least 3 meters).
• Decrease volume on Parent Unit.
THE PARENT UNIT SCREEN IS BLACK (PARENT UNIT IS OFF)
• Turn the Parent Unit back ON by pushing and holding the power button (left ‘wing’)
for 2 seconds.
• Replace the batteries or recharge Parent Unit.
LOSS OF CONNECTIVITY
In the case of loss connectivity, the first step is to bring the Parent Unit and the Nursery
Unit closer together and make sure that both units are ON to restore the connection.
If there is still no connection and no out of range warning after the above has been done,
then and only then should the re-connection procedure below be done.
Re-Connection procedure:
3
2
1) Make sure both the Nursery Unit and
the Parent Unit are OFF.
2) Turn ON the Nursery Unit by pressing
the left wing.
The power light will turn on.
3) Press and release the left wing 4 times
until the Angel eye light and night light
blinks.
4
5
4) Turn ON the Parent Unit until the screen
displays.
5) Press and hold the Parent Unit Talk
button and then press and release the
Power button.
NOTE:
By doing the re-connection procedure you will
reset the monitoring system back to original presets.
26
The Parent Unit screen should
then show the video display - this
would mean that the units are now
connected.
LIMITED WARRANTY
Angelcare® warrants to the original owner of this product that Angelcare® rechargeable
video, movement and sound monitor (model AC1100) is free from any material and
workmanship defects, for a period of one (1) year from the date of the original purchase.
If this monitoring system fails to function properly when used as directed under normal
conditions within the two year period, Angelcare® will either repair or replace the product,
at our discretion, free of charge. Please contact your distributor.
The product must be accompanied by a proof of purchase, either a bill of sale or other
proof that the monitoring system is within the warranty period. Angelcare® will bear the
cost of repairing or replacing the product and shipping it back to you.
This warranty does not apply to a product which has been damaged as a result of
improper maintenance, an accident, improper voltage supply or any other form of
misuse. The warranty is also void if the owner repairs or modifies the product in any
way. Angelcare® is not liable for any incidental or consequential damages with regard
to this product. The warranty also excludes any liability other than what is stated above.
No other warranty is given.
This warranty does not cover products and accessories which are not Angelcare-branded,
or any problems that result from usage that is not in accordance with product instructions,
failure to follow the product instructions, or problems caused by using accessories, parts or
components not supplied by Angelcare.
LEGAL RIGHTS VARY FROM COUNTRY TO COUNTRY. SOME COUNTRIES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
WE ARE NOT IN ANY WAY RESPONSIBLE FOR ANY OUTCOME RESULTING FROM
THE USE OF THIS PRODUCT.
IMPORTANT!
This Angelcare® monitor is a personal care product. Please do not return this product
to the store. If you have questions or need help, please call your distributor before
returning this product.
27
TECHNICAL SPECIFICATIONS
They may only be replaced by
3 AAA NIMH rechargeable batteries.
Range:
Open field (Open area without
obstructions): up to 200 meters.
Batteries:
Number of Channels:
USA/Canada: 19 channels.
Europe: 64 Channels.
Power Supply:
Three AAA alkaline batteries (not included)
or 7.5V DC Adapter for Nursery Unit.
Three AAA rechargeable batteries and
7.5V DC adapter for Charging Base for the
Parent Unit.
Caution: To reduce the risk of electric
shock, do not expose this product to rain
or moisture.
• DO NOT mix old and new batteries.
• DO NOT mix alkaline standard
(carbon-zinc), or rechargeable
(NI-CD, NIMH, etc) batteries.
Transmission:
Data transmission between the Parent
Unit and Nursery Unit is made on the
2.4GHz frequency.
Hereby, Angelcare Monitors Inc, declares
this baby monitor is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
The EU declaration of conformity can be
obtained at: www.angelcarebaby.com
Danger of explosion if batteries are
incorrectly replaced. The included Batteries
are 3 AAA NIMH rechargeable batteries,
manufactured by GPI INTERNATIONAL
LIMITED (GN60AAAHC, 1.2V 600mAh) or
by HIGHPOWER TECHNOLOGY CO., LTD
(HFR-44AAAJ600, 1.2V 600mAh).
PROTECT THE ENVIRONMENT
This electronic equipment contains reusable material and must not be disposed
with domestic waste. Please take it to a collecting point for electric and electronic
equipment (ask your local authorities for details).
ErP COMPLIANCE
SOUTH AFRICA-BRAZIL-ECUADOR-EUROPEAN UNION
Use only Angelcare® Brand power supply-model number T07505V001
GERMANY
Use only Angelcare® Brand power supply-model number T07505F002
AUSTRALIA
Use only Angelcare® brand power supply-model number T07505S002
NORTH AMERICA
Use only Angelcare® brand power supply-model number T07505U002
28
29
30
31
This Angelcare Baby Monitor is a Personal Care Product. Please DO NOT return
this to the store, but contact us initially for advice and assistance:
Angelcare Helpline on 0345 009 1789
Website: www.angelcare.co.uk
Email: helpline@babyhelpline.co.uk
NOTE: Helpline is open Monday to Friday, 10am to 4pm, excluding bank holidays.
IM1100-UK-140915
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising