ScreenBeam Pro Business Edition Wireless Display Receiver1

ScreenBeam Pro Business Edition Wireless Display Receiver1
ScreenBeam Pro Business Edition
Wireless Display Receiver1
Quick Start Guide
This Quick Start Guide provides step-by-step instructions
on how to setup your Actiontec ScreenBeam Business
Edition Receiver. After completing the steps described in
this Guide, you will be able to place the Receiver at your
site and provide wireless display access for users.
Setup Requirements
EConnect Laptop to Receiver
Windows 8.1 or Windows 10 laptop with Miracast
wireless display enabled
1. Learn how to connect your device:
TV/Projector/Monitor with HDMI input
Wi-Fi channel scanner tool
2. On the Windows 8.1 laptop, go to Devices > Project
> Add a wireless display. For Windows 10, go to
Action Center > Connect > Select the Actiontec
wireless display receiver.
If the Receiver is deployed with Central Management
System (CMS), refer to the CMS Deployment Guide. Go to for more information.
3. Verify the name on the list is the same as the
Receiver’s name shown on the Ready to Connect
screen (in the bottom left corner).
4. Select the Receiver’s name to connect.
Note: The PIN is randomly generated and will appear
on the Ready to Connect screen.
Before You Begin
Before deploying Actiontec ScreenBeam products, check
for the latest software and release documentation.
D Connect Receiver to Display
1. Place the Receiver next to the TV display.
For user guides and software upgrades, go to:
2. Using an HDMI cable, connect one end to the Receiver’s
HDMI port and the other end to the HDMI port on
the TV.
For Open Source information, go to:
3. Turn on the TV and switch to the HDMI input to which
the Receiver is connected.
4. Connect one end of the Receiver’s power adapter to
the Receiver’s power port, and the other end to an
electrical wall socket.
Package Contents
ScreenBeam Business Edition Wireless Display Receiver
Power adapter
HDMI cable
Regulatory notice
Quick Start Guide (this document)
5. Wait about 30 seconds, then verify the TV displays
ScreenBeam’s Ready to Connect screen.
Log Into Local Management
1. On the laptop, open a web browser.
2. Enter the following URL into the browser’s address
text box:
3. When the Actiontec Login console page appears,
enter the following:
Username: Administrator
Password: WiDi
4. Click OK.
5. The Device Configuration webpage appears.
Flip this Guide over to continue
Catalog #s SBWD100BE02, SBWD100BEPROMO
G Customize Wireless Display Settings
Assign New Device Name
Configure HDMI-CEC
1. Go to the Device Configurations webpage.
If the Receiver is connected behind an A/V transmitter or
receiver, enable this mode to support CEC (Consumer
Electronics Control).
2. From the Device Name Access option, select Enable.
3. Click in the Device Name text box, then enter a new
name (example: Conference TV).
Note: Each Receiver should have a unique name; this
makes it easier to identify which Receiver is connected
to which TV/projector. The recommended characters
are (A-Z, a-z, 0-9, -, _).
2. Click Apply to save changes.
Configure Force PIN Pairing Option
2. Move the Receiver to its permanent location (accessible
to both power and HDMI/VGA input of the display).
Note: If you plan to use CMS, access to a wired
(recommended) or wireless LAN is also required.
1. If the Receiver connects to the TV/projector via VGA,
select either 1080 or 720, depending on the resolution
of the display.
3. Plug the HDMI or VGA cable to the Receiver and the
2. Click Apply to save changes.
4. Plug in the Receiver’s power adapter.
5. Switch the TV/projector to the correct input, and
verify the Ready to Connect screen appears.
Set Up Wi-Fi Direct Wireless Channel
H Customize Wireless Display Features
1. Unplug the power adapter and HDMI cable from the
Configure VGA Compatibility Mode (Optional)
Change the Administrator’s Password
1. Click in the Administrator Password text box and
enter the new password.
Place Receiver at Site
Before selecting a wireless channel, consult with the
wireless network administrator. We recommend using
either MetaGeek inSSIDEer for Windows or WiFi Analyzer
for Android to scan for the least congested wireless
channel for the Receiver. Also, for best results, select a
wireless channel on the 5GHz band.
Verify the Installation
1. Using an Intel Pro WiDi-enabled device, connect to
the Receiver.
2. The device’s screen appears on the TV/projector. The
screen can now be mirrored or extended on the
1. Go to the Features webpage. By default, any new
system that connects to the Receiver must enter a
randomly-generated PIN.
1. Go to the Network Settings webpage.
2. Change the PIN (password), if desired.
2. Go to the Channel Number drop-down menu.
Configure HDMI/VGA Port Power Management
3. Select a wireless channel. If there are no wireless
channel restrictions, select the least congested channel.
Congratulations! The TV/projector is now connected
to the Receiver, and is wirelessly displaying content from
the device.
4. Click Apply to save changes.
For More Information
The Receiver is designed to display continuously. To
extend the TV/projector’s bulb life, change the Receiver’s
output to ScreenSaver or Display Off (for the latter, enter a
desired period until the display turns off).
Note: When the Receiver goes to Display Off mode,
the TV/projector will show a blank screen. A Miracast/
WiDi scan or connection will wake up the device.
Some TVs or projectors may attempt to switch input
on their own to discover an active A/V signal.
PN 0530-0721-003
For Intel Pro WiDi support and additional information, go to:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF