advertisement
Carbonite
Configuration Guide
v11.1
Document Information
• Ross Part Number: 4802DR-100-11.1
• Release Date: September, 2015.
The information contained in this document is subject to change without notice or obligation.
Copyright
©
2015 Ross Video Limited, Ross
®
, CrossOver
®
,
MiniME
™
, and any related marks are trademarks or registered trademarks of Ross Video Limited. All other trademarks are the property of their respective companies.
PATENTS ISSUED and PENDING. All rights reserved.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of Ross
Video. While every precaution has been taken in the preparation of this document, Ross Video assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Microsoft
®
, Windows
®
, and Windows XP
® are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
NVIDIA
® and GeForce
® are trademarks and/or registered trademarks of NVIDIA Corporation in the U.S. and/or other countries.
Patents
Patent numbers US 7,034,886; US 7,508,455; US
7,602,446; US 7,802,802 B2; US 7,834,886; US
7,914,332; US 8,307,284; US 8,407,374 B2; US
8,499,019 B2; US 8,519,949 B2; US 8,743,292 B2; GB
2,419,119 B; GB 2,447,380 B; and other patents pending.
2 • Document Information — Carbonite Configuration Guide (v11.1)
Contents
Features..............................................................5
Custom Controls.....................................................................5
Device Control.........................................................................5
®
Caprica Support...................................................5
DVE (Fly Key)..........................................................................5
Effects Dissolve.......................................................................5
General Purpose Interface (GPI)............................................5
LiveEDL...................................................................................5
Media-Store.............................................................................5
MediaWipe..............................................................................6
UltraChrome............................................................................6
MemoryAI Recall Mode...........................................................6
Memory System......................................................................6
ME Effect System....................................................................6
Half ME...................................................................................6
™
..................................................................................6
MediaManager........................................................................6
MultiViewer..............................................................................6
Clean Feed Output..................................................................7
MultiScreen.............................................................................7
Pattern and Matte/Wash Generators.......................................7
Matte/Wash Generator............................................................7
Tally Outputs...........................................................................7
Product Comparison..........................................8
Carbonite Black Control Panels..............................................8
Carbonite Frame.....................................................................8
Standard System................................................9
Carbonite Black Control Panel................................................9
Carbonite Frame.....................................................................9
System Options................................................10
Specifications...................................................14
Switcher Resources..............................................................14
Environmental Characteristics..............................................14
Video Input Specifications.....................................................14
Video Output Specifications..................................................14
Audio Specifications..............................................................14
Jitter......................................................................................15
System Timing......................................................................15
Power Consumption — Control Panel...................................15
Power Consumption — Frame..............................................15
Option Summary..............................................16
Frame Options.......................................................................16
Control Panel Options...........................................................17
Panel Dimensions............................................18
CB1.......................................................................................18
CB1S.....................................................................................18
CB2.......................................................................................18
CB2S.....................................................................................18
CB3S.....................................................................................19
CB3X.....................................................................................19
Frame Dimensions...........................................20
Carbonite Frame...................................................................20
Carbonite eXtreme Frame.....................................................20
Carbonite Black Frame..........................................................20
Carbonite Configuration Guide (v11.1) — Contents • 3
Carbonite
Designed for Live!
Carbonite builds on the Ross Video reputation for designing switchers for live studios, trucks, and post-production. At the center of the action, it is important that the switcher be powerful and versatile, yet maintain its ease of operation. This frees the operator to concentrate on the programming instead of the equipment, delivering a cleaner, more professional production.
Carbonite eXtreme represents the cutting edge in video production innovation. By combining the video manipulation power of the Carbonite video production switcher with the robust signal routing and management of the NK-3G144-X router you have a combination that offers tremendous flexibility in operation and configuration with a significant cost savings. Whether it is a mobile application where space is paramount, or an event based application where destination based routing is the norm, Carbonite eXtreme delivers.
Carbonite Black improves on the highly popular
Carbonite series by bringing up to 3 MEs, 4 MiniME
™ outputs, more I/O, dedicated AES audio outputs, and full
DashBoard integration with a touchscreen display. All this in the same compact 2RU frame form factor and intuitive control panel you have come to expect.
Designed for Automation!
The Carbonite family of switchers support the highly advanced OverDrive
®
Caprica automated production control system. Caprica takes advantage of the years of device integration that Ross
® has developed in the large switcher product lines and puts it into an independent server. The Caprica server takes the place of the production switcher for controlling over 200 additional production elements (such as robotics, graphics, audio mixers, servers, etc.), timing the show and creating production macros.
Designed for Linear!
The Carbonite family of switchers continues to build on
Ross
®
Video's reputation for setting the standard for multi-definition linear editing suites. The traditional layout and familiar controls of other Ross
® switchers provide the power and ease of use you have come to expect.
Carbonite cleanly connects to virtually any editor using the industry standard GVG100/110 protocols.
Designed for You!
With Ross
®
Video products installed in well over 125 countries world-wide, our sales, demonstration, and training people get a lot of ongoing feedback from customers. This feedback is carefully tracked and considered in the design and feature-set development of our products. Key members of the design teams are part of an ongoing program in which they provide product demonstrations, assist with product installation, and train operators. As a result, the complete line of Ross Video products continues to offer our legendary combination of power and ease of use.
Join our Growing Customer Base!
Deciding to purchase a Carbonite switcher will put you in good company, with many thousands of Ross switchers installed worldwide. Carbonite continues to build on a family of multi-definition switchers that have been delivering the goods every day in live sports, stadium scoreboards, and drama productions, mobile productions, as well as local and network newscasts.
Experience Great Support!
Ross
® has designed and manufactured production switchers for over 40 years, with significant year over year growth for the past 20 years. We believe that an important factor of our success is our focus on providing a superior customer experience. We continually benchmark our warranty and technical support to ensure that they are the best in the industry.
We hope that you join the many thousands of satisfied video professionals around the world that are proud owners of Ross
® production switchers. Please do not hesitate to contact us with any questions or comments you have related to this Configuration Guide at Tel:
+1-613-652-4886, Fax: +1-613-652-4425 or email us at
.
4 • Carbonite — Carbonite Configuration Guide (v11.1)
Features
Thank you for your interest in the Ross
®
Carbonite Series
Multi-Definition Live Production Switcher. The
Carbonite series builds on the Ross
® reputation for designing switchers that fit the needs of any production environment.
Custom Controls
This feature brings the power of macros to the switcher operator. Button presses, menu selections, event commands, or even the switcher state can be recorded to a custom control with pauses or holds between the events.
A simple button press can play these events back again.
Step through complex show openings as easily as pressing Custom Control buttons 1, 2, then 3.
Device Control
The switcher can control a number of external devices, such as video servers and robotic cameras. For a complete list of supported devices, and information on how to set up and control these devices, visit the Ross Video website
(
rossvideo.com/production-switchers/carbonite/interface-list
).
OverDrive
®
Caprica Support
Carbonite can be controlled from OverDrive
® using the
Caprica interface. This interface allows OverDrive
® to perform memory recalls, transitions, and run custom controls on the switcher. For information on setting up
Caprica to interface with the switcher, refer to the documentation that came with your Caprica server.
The switcher must be in a 2.5 ME mode or have 3 MEs installed to be controlled by Caprica.
DVE (Fly Key)
The advanced 2D DVE comes standard with each switcher, and can be used for performing over the shoulder, or picture in picture shots. This allows all key types to be zoomed, cropped, and repositioned horizontally and vertically to create the look you want, or you can use one of the useful pre-built 2D effects to perform 2D background transitions.
The Carbonite+ and Carbonite MultiMedia frames have
8 channels of DVE, or 4 channels in a 3G MiniME
™ or
3G 2.5 ME switcher mode. The Carbonite and Carbonite eXtreme frames can select between 8 channels of DVE and 0 FSFCs, or 4 channels of DVE and 6 FSFCs.
Effects Dissolve
The Effects Dissolve feature allows you to interpolate from one memory to another using a memory recall. The switcher will interpolate from the starting memory to the destination memory, creating a smooth, two key frame effect.
Source
Effect
Destination
Effect
Only elements such as clip level and pattern position can be interpolated in the effects dissolve. Other elements, such as crosspoint selection, pattern, and next transition data are recalled first, and then the switcher will slew to the recalled memory.
An effects dissolve can be performed on as many elements and MEs as required, based on the memory that is being recalled.
General Purpose Interface (GPI)
The switcher is equipped with 34 GPI I/Os that can be assigned as either an input or output independently.
The GPI inputs allow the switcher to interface with peripheral equipment such as editors. Each GPI input can be used to perform simple editing and switcher functions such as fade to black or an auto transition.
LiveEDL
Edit Decision Lists (EDL) are files used by non-linear editing (NLE) suites to aid in post-production. Your switcher can capture EDL data in a file that you load into your NLE suite.
For information on using the LiveEDL feature, visit the
Ross Video Website (
rossvideo.com
).
Media-Store
Up to 4 independent channels of still/animations are available switcher-wide, allowing for thousands of full screen stills and logos that can be cached and used on the switcher.
Media-Store provides 8 GB of cache. Channels 1 and 3 have 4 GB, and channels 2 and 4 have 4 GB. The number of images cached increases considerably when smaller, non-full screen images like logos are loaded from USB.
Carbonite Configuration Guide (v11.1) — Features • 5
MediaWipe
A MediaWipe allows you to use an animation from the
Media-Store to perform background and key transitions.
When the transition starts, the switcher plays the selected animation over top of the background and keys that are being transitioned. A cut is then performed behind the animation to bring up the next shot when the animation ends.
UltraChrome
The UltraChrome chroma keyers uses advanced video processing technology to provide exceptional blue spill reduction and clean edges, even with difficult source material. Glass, smoke, translucent materials, and natural shadows are handled superbly.
There are 2 floating Chroma Keys that are available across all MEs.
MemoryAI Recall Mode
We take the guessing out of memory recalls by ensuring that a memory recall will not affect what is currently on-air. MemoryAI uses the content of the memory to configure the Next Transition area and Preview bus for the background and keyers so that the next transition takes the same sources on-air that were on-air in the memory.
For example, store a memory that has a key on-air with
CAM1 and CAM2 selected on the background. When this memory is recalled normally, it pops the same key on-air with CAM1 and CAM2 on the background. When the memory is recalled with MemoryAI turned on, CAM1 is selected on the preset bus, and CAM2 is selected on a key that is not on-air. The transition area is then set up for a background transition to bring CAM2 onto the background, take any on-air keys off, and take a key on-air with CAM1.
Memory System
Storage for 100 complete switcher snapshots per ME,
MiniME
™
, and MultiScreen comes standard with all switchers. All of these memories can be stored to a USB media drive, providing custom tailored memories for every operator and every show.
ME Effect System
The ME (Multi-level Effect) systems are standard. The number of MEs depends on the chosen switcher model.
Each ME provides 4 keyers supporting pattern mask, box mask, self-key, linear key, and UltraChrome advanced chroma key for each ME and is available to each keyer.
Half ME
The half ME option is available for any 2 ME Carbonite or Carbonite eXtreme switcher and adds a third ME with limited functionality.
Table 1: Half ME vs. Full ME Comparison
MiniME
™
MultiScreen
Floating FSFCs
Keyers
Key Types
Transition Types
Pattern Mask
Half ME
No
Full ME
Yes
No
No
Yes
Yes (if frame supports it)
4 2
Auto Select and
Self Key
Auto Select, Self
Key, Chroma
Key, and DVE
Key
Dissolve, Cut, and MediaWipe
Dissolve, Cut,
Wipe, DVE, and
MediaWipe
No Yes
MiniME
™
The MiniME
™ is an additional ME that is provided with the switcher to perform basic dissolves and cuts. Each
MiniME
™ has 2 keyers, background, and preset buses.
Unlike a full ME, the MiniME
™ only supports dissolves and cuts, restricts key 1 to DVE keys only, and has no preview output. Key 2 on a MiniME
™ is the same as an
ME keyer. The MiniME
™ shares all the same sources as the ME.
MediaManager
The MediaManager allows you to easily manage stills and animations on the switcher in a graphics interface.
MultiViewer
Each MultiViewer allows you to view up to 16 video sources, in 32 different layouts, from a single output
BNC. Any video source on the switcher, including ME
Program, Preview, and Media-Store channels, can be routed to any box on the MultiViewer. All boxes on the
MultiViewer output include mnemonic source names and red and green tallies.
All Carbonite and Carbonite Black switchers come standard with 2 broadcast-quality integrated MultiViewer generators.
6 • Features — Carbonite Configuration Guide (v11.1)
Note:
If Carbonite is operating in 3G video mode, the number of video sources and layouts is reduced.
PGM/
PST
KEY 1 KEY 2 KEY 3 KEY 4 PGM
CLEAN
FEED
MultiScreen
All Carbonite switchers come standard with 2 integrated
MultiScreen generators. Each MultiScreen can break a scene into up to 4 outputs that can be sent to independent projectors or displays to make a unified picture.
Integrated edge blending allows you to compensate for the overlap in projector outputs, or the outside bezel of your display.
Each screen in the MultiScreen output uses a MiniME
™ to create the background and keys of the output. This allows you to have 2 MultiScreen generators with 2 screens each, or 1 MultiScreen generator with 3 or 4 screens.
Edge
Area
MultiScreen 1
Edge
Area
Key
Figure 1: HD Layouts
If Carbonite is operating in a standard-definition video format, the MultiViewer can be set to output high-definition. In HD output mode, the MultiViewer is only available on specific output BNCs and only supports
29 different layouts.
Carbonite Black automatically outputs high-definition, but each MultiViewer is only available on specific output
BNCs.
Figure 2: HD in SD Layouts (480i 4:3)
Clean Feed Output
Clean feed is typically used for bilingual and live-to-tape productions. It provides a second Program output that is derived from a different location than the standard program output. A frequent application is the recording of shows for later airing without call-in phone numbers inserted.
The clean feed output can come from before or between the keyers.
MiniME 1 MiniME 3
MiniME 2
Pattern and Matte/Wash Generators
A single pattern generator dedicated to wipes comes standard, and is equipped with 10 classic wipes. Most wipes can be rotated, bordered, multiplied, aspectized, and repositioned.
Matte/Wash Generator
A matte generator and complex wash generator per ME, capable of multi-color washes comes standard. Any one of the color generators can be assigned to MATTE, or wipe pattern edges. An additional simple color generator is available for an Aux Bus.
Tally Outputs
The switcher has 34 assignable tally relays located in the rack frame. Each tally can be assigned to any number of combinations of input and output or bus.
Carbonite Configuration Guide (v11.1) — Features • 7
Product Comparison
Use the following table to compare the different switchers in the product line.
Carbonite Black Control Panels
CB1S CB2 CB2S CB3S CB1
Control Panel
Panel Source Buttons per Control Panel
Row
Number of Control
Panel Rows
Number of User
Assignable Buttons
Total Panel Source
Buttons
Maximum Number of
MEs Supported
Maximum Number of
MiniME
™
Engines
Custom Control
Buttons
16
1
4
16
16
Custom Control Bank
Buttons
Source and Keyer
Mnemonics
4
Legendary Ross
Fader Handle with
Lifetime Guarantee
Positioner
ME Memory Keypad No
Engineering and Networking
Redundant Power
External Link Port
Ethernet Connectivity
24
1
8
24
24
4
Yes
16
2
4
32
16
4
3
4
Yes
Yes
24
2
8
48
24
4
No
3 Axis
Yes
24
3
8
72
24
4
Yes
Yes (optional)
2 (not available at this time)
2 × GigE (only 1 is available at this time)
CB3X
32
3
12
96
32
8
Yes
Carbonite Frame
Carbonite Carbonite+ Carbonite
MultiMedia
Carbonite eXtreme
Carbonite
Black
Frame
Separate Rack Frame
Rack Frame Height
Redundant Power
Yes
2 RU
Yes (optional)
Video Input/Output
Multi-Definition HD/SD 1080i 50/59.94, 720p 50/59.94, 1080pSF 23.98/25/29.97, 1080p
29.97
Standard Definition
Processing
SDI Inputs (Max)
HDMI Inputs (Max) 0 0
24
525, 625
4 0
36
0
Analog Inputs (Max)
SDI Outputs (Max)
0 0
10
4 0 0
22
8 • Product Comparison — Carbonite Configuration Guide (v11.1)
Ethernet Connectivity
Linux OS
Animated Logo Players with Audio (requires video and alpha playout)
Peripheral Interfacing
Device Control
OverDrive
®
Compatible
Caprica
Roll Clip Control
External Link Ports
Serial Ports
Ethernet Serial Port
Expanders
Automation and Editor
Protocols
GPI I/Os
Tallies
USB Ports
Clean Feed System
FSFCs (Max/Min)
Input Reference Format
Carbonite Carbonite+ Carbonite
MultiMedia
Carbonite eXtreme
Carbonite
Black
6/0
Yes
24 24 6/0
Internal / Black Burst / Tri-Level
6/0
Independent Reference
Inputs
Independent Reference
Outputs
1
2
2 MultiViewer Generators
Effects Capabilities
Keys per ME
2D DVE Channels per
ME (Max/Min)
Proc Amps and Color
Correctors
Memory AI
UltraChrome Chroma
Keys
Storage and Networking
USB Media Drive
Media-Store Channels
Media-Store CACHE
Audio Only Playout for
Media-Store
No Yes
4
8/4
Yes
Yes
2
Yes (user supplied USB 2.0)
4
8 GB
Yes
No No
Comtrol
®
2 GigE
Yes
Yes
Yes
Yes
AMP/RossTalk/GPI Output
1
1 (RJ45)
DeviceMaster
34
34
1 (Frame)
®
RTS Series
RossTalk/GVG100
Standard System
Whether you have a demanding production environment, or a more modest one, selecting the Carbonite
Multi-Definition Live Production Switcher that is right for you should not be a complicated task.
Carbonite Black Control Panel
Select the control panel that meets the needs of your production environment and that utilizes the power of your Carbonite Black Multi-Definition Live Production
Engine.
Option
CB1-PANEL
CB1S-PANEL
CB2-PANEL
CB2S-PANEL
CB3S-PANEL
CB3X-PANEL
Description
A single panel row with 16 source and custom control buttons, 4 key select and transition buttons, 4 key type buttons, 4 aux bank buttons, and 4 custom control bank buttons.
The same features as the previous panel, but with 24 source and custom control buttons, 8 aux bank buttons, an expanded global memory area, and an effects memory keypad per
ME.
The same features as the CB1 panel, but with 2 panel rows.
The same features as the CB1S panel, but with 2 panel rows.
The same features as the CB1S panel, but with 3 panel rows.
The same features as the CB3S panel, but with 32 source and custom control buttons and 4 user assignable buttons.
Carbonite Frame
When selecting a Carbonite frame, replace the y with the number of MEs. For example, CF-216PLUS is the option code for a 2 ME (2), 16 input (16), Carbonite+ (PLUS) frame.
Note:
The 16 input Carbonite MultiMedia frame only supports
2 MultiMedia inputs.
Note:
Each switcher subsystem in the Carbonite eXtreme has a maximum of 24 video inputs and 10 video outputs. Video signals coming into the router must be routed to the inputs of the switcher subsystem for the switcher to have access to them.
Similarly, video outputs from the switcher subsystem must be routed to a router output.
Option
CF-y16
Description
Carbonite frame with (y) MEs and 16 inputs.
Option
CF-y24
CF-y16PLUS
CF-y24PLUS
CF-y16MM
CF-y24MM
CF-224EX-16
CF-224EX-48
CF-224EX-96
CBF-236
Description
The same features as the previous frame, but with 24 inputs.
Carbonite+ frame with (y) MEs and
16 inputs.
The same features as the previous frame, but with 24 inputs.
Carbonite MultiMedia frame with (y)
MEs and 16 inputs.
The same features as the previous frame, but with 24 inputs.
Carbonite eXtreme frame with 2 MEs,
24 inputs, and 16 outputs.
The same features as the previous frame, but with 48 outputs.
The same features as the previous frame, but with 96 outputs.
Carbonite Black frame with 2 MEs,
36 inputs, and 22 outputs.
Carbonite Configuration Guide (v11.1) — Standard System • 9
System Options
Options are typically ordered when the switcher is purchased. However, you can order options if your needs change in the future. Most of our options can be easily installed in the field. You can take comfort in knowing that you can purchase options in the future and that installation at your site will be a smooth process.
XPression
™
Live (XDS0-0001-CPS)
Seamlessly combine the creative power of the Ross
®
XPression Designer software with the ease of use of your
Ross
® switcher. Create stunning still graphics using
XPression Designer, and transfer them directly to an media-store channel on the switcher using the RossLinq interface. Up to two (2) channels with dedicated alpha can be controlled from the XPression Software Client.
This feature supports still images only.
The XPression Designer requires a computer with a
Windows
®
7 (32/64 But) operating system and an
NVIDIA
® graphics card.
Redundant Power
The redundant power supply options provides protection against AC power failure. It allows two external power supplies to receive power from independent power sources. Complete failure of one source, or power supply, will not affect the operation of the switcher in the slightest. If the main AC power fails, the switcher instantly draws power from the remaining source. The transition from one power source to the other is totally transparent and has no effect on the output of the switcher; a critical feature should one power source fail during an on-air broadcast.
Option
PSU-12V16A-6PIN
CF-NK-P3G
PSU-48V5.9A-4PIN
Description
Adds a redundant power supply for the Carbonite, Carbonite+, and
Carbonite MultiMedia frames, as well as the Carbonite Black control panels.
Adds a redundant power supply for the Carbonite eXtreme frame only.
Adds a redundant power supply for the Carbonite Black frame only.
16 Input to 24 Input Upgrade
(CF-16IN-24IN-UPG)
This option increases the number of SDI video inputs on the Carbonite frame from 16 to 24 and the number of
MultiMedia inputs on the Carbonite MultiMedia from 2 to 4. All inputs can be used direct to air, as key alpha channels, or as chroma key sources.
Inputs can be freely assigned to any panel source button or shifted button. They can also be hidden and accessed only as alpha channels or they can be locked out if they are not used.
Note:
All Carbonite, Carbonite+, and Carbonite MultiMedia frames comes with a full 24 SDI video input BNCs. This upgrade option unlocks the additional BNCs in software.
1 to 2 ME Upgrade
(CF-1ME-2ME-UPG)
This option increases the number of MEs in your
Carbonite, Carbonite+, Carbonite MultiMedia, or
Carbonite eXtreme switcher from 1 to 2.
Note:
The half ME feature comes standard with the 2 ME option on these frames.
Carbonite Black comes standard with 2 MEs and can be upgraded to 3. Carbonite Black does not support the half
ME feature.
2 to 3 ME Upgrade (CBF-ADD-ME3)
This option increases the number of MEs in your
Carbonite Black switcher from 2 to 3.
Video Inputs (CF-NK-I3G)
This option adds a card to the Carbonite eXtreme frame that provides support for 8 additional video inputs.
Note:
A rear connector (CF-NK-I3G-RC) is required for every two CF-NK-I3G options. The rear connector provides the BNCs at the back of the frame.
Video Outputs (CF-NK-O3G)
This option adds a card to the Carbonite eXtreme frame that provides support for 8 additional video outputs.
Note:
A rear connector (CF-NK-O3G-RC) is required for every two CF-NK-O3G options. The rear connector provides the BNCs at the back of the frame.
Carbonite eXtreme Second Switcher
Upgrade (CF-EX-2NDSWR-UPG)
Carbonite eXtreme can be upgraded to include two independent switcher subsystems (switcher A and switcher B). Each switcher subsystem has access to all the inputs and outputs of the router subsystem. A router output can only be assigned to a single switcher output.
This upgrade installs the Carbonite eXtreme CPU into the second slot, and adds a number of cards to the system to support the switcher.
10 • System Options — Carbonite Configuration Guide (v11.1)
This option comes with a secondary Controller card,
Breakout Panel, Ethernet Interface card, and GPIO/Tally card with rear module.
Caution:
The upgrade of the Carbonite eXtreme with a second switcher must be limited to service personnel only and must be performed with the frame/chassis in a de-energised state.
Important:
The Carbonite eXtreme second switcher upgrade is only compatible with Carbonite eXtreme
/ NK-3G144-X frame (2500AR-202-xx) running software version 8.0 or higher. If you do not have this frame or software, or are unsure about the model of your frame, please contact Ross Video Technical
Support for more information.
SideShot Custom Control Shot Box
(CPS-SideShot)
This option provides quick access to the first 24 custom controls on the first 4 custom control banks of the switcher.
Remote Panels
This option provides external control for selecting sources on an Aux bus from a remote panel. There are a number of options for the remote control panels, depending on your requirements.
On Carbonite eXtreme these panels can be configured to operate as an X-Y, cut-bus or multi-cut bus panel for the router subsystem, or as a control panel to select sources any bus or run custom controls for the switcher sub-system. Every control panel in the system can be independently configured to meet the needs of the particular operator. Connects to the switcher through an
NK-IPS over ethernet (T-BUS connection between the
NK-IPS and remote control panel).
On Carbonite and Carbonite Black these panels connect to the switcher through an NK-IPS over ethernet (T-BUS connection between the NK-IPS and remote control panel).
Option
NK
RCP-NKM
RCP-NKQ
Description
Adds the 32 source button NK remote control panel.
Adds the 40 source button RCP-NKM remote control panel with integrated backlit display.
Adds the 17 mnemonic button
RCP-NKQ remote control panel.
DashBoard Display
(CBPS-DashMenu)
The DashBoard Display combines a DashBoard computer with a touchscreen into a single unit that can be installed onto a standard VESA-100 mount. The DashBoard
Display connects to the switcher over ethernet to provide the advanced menu system interface to the setup and operation of your Carbonite or Carbonite Black switcher.
The DashBoard Display eliminates the need to connect another computer to your switcher network just to run
DashBoard.
SMC-9901 Serial to MIDI Converter
(SMC-9901)
The SMC-9901 Serial to MIDI Converter is used to allow control of an Audio Mixer from a Ross Video switcher.
The SMC-9901 provides a single DB-9 connector for
38,400 baud serial RS-422 communication, one 5-pin
DIN connector for MIDI in, and two 5-pin DIN connectors for MIDI out. Power, Serial Tx and Rx, MIDI
In and MIDI Out Status LEDs next to the ports show activity status.
The SMC-9901 connect to the switcher via the serial port on the frame, or an external port expander such as the
Comtrol
®
DeviceMaster
®
.
SHC-9642 SDI to HDMI Converter
(SHC-9642)
The SHC-9642 SDI to HDMI Converter is a high-quality signal conversion solution within the family of GearLite compact, self-contained modular products. The
SHC-9642 is the ideal solution for converting any SDI input signal (up to 3Gb/s) into an HDMI Type-A output format. User-selectable audio decoding is available with unbalanced, stereo analog audio outputs. Up to 16 channels of embedded audio are selectable, in stereo pairs, for de-embedding and decoding.
Onsite Operational Training
(CARBONITE-OTR-1DAY)
Although Ross Video switchers are designed to be as easy as possible to install and operate, training is highly recommended to ensure that the process of taking your
Ross Video switcher to air is a smooth one.
Training is provided on the customer's equipment at their site. Expenses are extra, and billed at the completion of the visit. Ross Video cannot guarantee the availability of a local Trainer, as such, travel costs to all locations will be invoiced at cost. Two (2) days, or more, of
Carbonite Configuration Guide (v11.1) — System Options • 11
training is recommended for multiple MLE systems. Four
(4) weeks advanced scheduling notice is required.
Additional days of training can be added with the
CARBONITE-OTR-1DAY option. Please quote one additional option for each additional day of training required.
Customers cancellation or rescheduling of on-site services without seven (7) calendar days advanced notice will incur full invoice.
Online Operational Training
(CARBONITE-ONL-1DAY)
Sometimes you don't need the hands-on attention that having a trainer come to your facility provides. In these situations Ross Video provides comprehensive, web-based, online training.
Two (2) days, or more, of training is recommended for multiple ME systems. Four (4) weeks advanced scheduling notice is required. Additional days of training can be added with the CARBONITE-ONL-1DAY option. Please quote one additional option for each additional day of training required.
Customers cancellation or rescheduling of on-site services without seven (7) calendar days advanced notice will incur full invoice.
Onsite Technical Training
(CARBONITE-OTT-1DAY)
On-site technical training introduces the user to some of the technical aspects of switcher operation and maintenance. This includes, but is not limited to; Basic operation, Switcher installation and configurations,
Peripheral interfaces, Video signal flow, System timing requirements, Circuit block diagrams, Circuit board overviews, Jumpers and indicators, Troubleshooting tips,
Software upgrading, and Routine maintenance.
Training is provided on the customer's equipment at their site. Expenses are extra, and billed at the completion of the visit. Ross Video cannot guarantee the availability of a local Trainer, as such, travel costs to all locations will be invoiced at cost. Two (2) days, or more, of training is recommended for multiple ME systems. Four
(4) weeks advanced scheduling notice is required.
Additional days of training can be added with the
CARBONITE-OTT-1DAY option. Please quote one additional option for each additional day of training required.
Onsite Commissioning
(CARBONITE-COM-1DAY)
On-site Commissioning is a great way to ensure that your switcher is properly installed into your facility and tuned to maximum performance.
Once the customer has installed and cabled the equipment, a Ross Commissioning expert will come on site to get the switcher configured, verify that all peripheral interfaces are operating properly, provide a basic technical orientation, and help you get on the air.
Training is provided on the customer's equipment at their site. Expenses are extra, and billed at the completion of the visit. Ross Video cannot guarantee the availability of a local Trainer, as such, travel costs to all locations will be invoiced at cost. Two (2) days, or more, of training is recommended for multiple MLE systems. Four
(4) weeks advanced scheduling notice is required.
Additional days of training can be added with the
CARBONITE-COM-1DAY option. Please quote one additional option for each additional day of training required.
Customers cancellation or rescheduling of on-site services without seven (7) calendar days advanced notice will incur full invoice.
Please note that commissioning does not replace operator or technical training. Contact your Ross representative to discuss which types of assistance are best suited to your needs.
Extended Warranty
This extends the standard one-year warranty on your control panel or frame by one year. Additional years can be purchased if required.
The Carbonite eXtreme comes standard with a 5-year transferable warranty. No extended warranty is available for this frame.
Option
CB1-PANEL-ROSSCARE
CB1S-PANEL-ROSSCARE
CB2-PANEL-ROSSCARE
CB2S-PANEL-ROSSCARE
Description
Adds an additional year of warranty to the CB1 control panel.
Adds an additional year of warranty to the CB1S control panel.
Adds an additional year of warranty to the CB2 control panel.
Adds an additional year of warranty to the CB2S control panel.
12 • System Options — Carbonite Configuration Guide (v11.1)
Option
CB3S-PANEL-ROSSCARE
CB3X-PANEL-ROSSCARE
CF-1ME-ROSSCARE
CF-2ME-ROSSCARE
CBF-236-ROSSCARE
CBF-336-ROSSCARE
Description
Adds an additional year of warranty to the CB3S control panel.
Adds an additional year of warranty to the CB3X control panel.
Adds an additional year of warranty to the 1 ME Carbonite frame.
Adds an additional year of warranty to the 2 ME Carbonite frame.
Adds an additional year of warranty to the CBF-236 frame.
Adds an additional year of warranty to the CBF-236 frame with the CBF-ADD-ME3 option installed.
Carbonite Configuration Guide (v11.1) — System Options • 13
Specifications
The information is this section is subject to change without notice.
Switcher Resources
The number of resources specific to your switcher depends on the options installed.
Resource
2D DVE Channels per
ME (Max/Min)*
Aux Buses
Chroma Keys per ME
Custom Controls
FSFCs (Max/Min)*
GPI I/Os
Keyers per ME
Matte Generators per
ME
Media-Store Channels
Carbonite Carbonite+ Carbonite
MultiMedia
Carbonite eXtreme
Carbonite
Black
8/4
6/0
8
2 (floating)
24
256 (8 Banks × 32 CCs)
24 6/0
34
4
2
4
8 GB
100
20
6/0
Media-Store CACHE
Memories per ME
MEs (max)
MiniME
™
Engines
MultiScreen Generators
MultiViewer Boxes
MultiViewer Layouts
MultiViewer Heads
Pattern Generators per
ME
Tallies
SDI Video Inputs
SDI Video Outputs
Fixed Frame IP (DIP switch 3)
Fixed Panel/CarboNET
IP (DIP switch)
2
24
4
2**
16
32
2
2
34
10
192.168.0.123
192.168.0.124
3
36
22
Notes
• * The number of DVE channels and FSFCs that are available depends on the switcher mode you are in.
This table assumes that all options are installed.
• ** Each MultiScreen consumes MiniME
™ engines to generate the output. The number of MultiScreen outputs that are available depends on the number of
MiniME
™ engines that are available.
Environmental Characteristics
Ambient Temperature Range
Frame Cooling
Control Panel Cooling
All Switchers
0 - 40°C (32 - 104°F)
Active, Front-to-Back airflow
Passive
Video Input Specifications
Input Specification Carbonite Carbonite Black
Equalization (using
Belden 1694 cable)
Reference Inputs
(non-terminating, looping
>50m @ 3Gb/s
>100m @ 1.5 Gb/s
Impedance
Video Inputs, SDI
Video Inputs, HDMI
>300m @ 270 Mb/s (5°-40°C)
75 ohms, terminating
SMPTE 259M/292M/424M serial digital
(non-looping)
HDMI 1.4
n/a n/a High Speed HDMI
Cable (Max 10m)
Video Inputs, Analog Input Impedance —
75 Ohm n/a
Levels — 1V peak-to-peak, nominal n/a
Standard Definition — analog black
High Definition — tri-level sync
Video Output Specifications
Output Specification
Return Loss
Rise and Fall Time
Signal Level
DC Offset
Overshoot
HD Mode
Value
<-23dB @ 1.5GHz
<-18dB @ 3GHz
800ps ±10% (SD)
240ps ±10% (HD)
800mV ±10%
0 Volts
<10%
10-bit SMPTE-292M/424M serial digital
Audio Specifications
Specification
Audio Depth
Channels
Carbonite Carbonite Black
24-bit AES3 in HD (20-bit in SD)
8 Stereo Pairs (16 channels)
1 Stereo Pair (2 channels)
14 • Specifications — Carbonite Configuration Guide (v11.1)
Specification
Output
File Format
Impedance
Minimum/Maximum output voltage swing
Rise and Fall Times
Sample Rate
Synchronization
Carbonite Carbonite Black
Embedded AES (×2 ports)
Multi-channel Waveform Audio File (.wav) n/a n/a
110 Ohms, differential
1.5/6V peak-to-peak n/a 20ns, typical
48kHz
Locked to Video
Jitter
Specification
HD - Tri-Level Sync
HD - Composite Reference
SD - Tri-Level Sync
SD - Composite Reference
Value
Alignment (> 100KHz) < 0.2UI
Timing (<10Hz) < 1.0UI
Performance not guaranteed with composite reference
Alignment (> 1KHz) < 0.2UI
Timing (<10Hz) < 0.2UI
Alignment (> 1KHz) < 0.2UI
Timing (<10Hz) < 0.5UI
System Timing
• All video inputs zero time relative to reference input, auto timing will correct for inputs out of time by up to +/- 0.25 line.
• System delay is less than 1 line.
Power Consumption — Control Panel
Consumption
Input Voltage
CB1
25W
2.1A
12V
CB1S
30W
2.5A
12V
CB2
35W
2.9A
12V
CB2S
45W
3.8A
12V
100 - 120V~
220 - 240V~
47-63Hz
1.6A
CB3S
65W
5.4A
12V
CB3X
80W
6.7A
12V
Power Consumption — Frame
Carbonite Carbonite+ Carbonite
MultiMedia
Carbonite eXtreme
Carbonite
Black
Consumption 90W 7.5A
12V
110W 9.2A
12V
125W
10.4A 12V
500W 34A
14.6V
120W 2.5A
48V
Input
Voltage
100 - 120V~
220 - 240V~
47-63Hz
1.6A
Carbonite Configuration Guide (v11.1) — Specifications • 15
Option Summary
Use the available options listed in the following tables for each control panel or frame.
Frame Options
Carbonite Carbonite+ Carbonite
MultiMedia
Carbonite eXtreme Carbonite Black
Frames
1 ME, 16 Inputs
1 ME, 24 Inputs
2 ME, 16 Inputs
2 ME, 24 Inputs
2 ME, 36 Inputs
2 ME, 48 Inputs
2 ME, 96 Inputs
Frame Options
1-2 ME Frame Upgrade
2-3 ME Frame Upgrade
Redundant Power, Frame
Extended Warranty, 1 ME Frame
Extended Warranty, 2 ME Frame
Extended Warranty, 3 ME Frame
Carbonite eXtreme Options
Video Inputs (8 SDI)
Video Inputs Rear Connector
Video Inputs (8 SDI)
Video Inputs Rear Connector
Upgrade from NK-3G144-X
Router
Second Switcher Subsystem
Redundant Controller Card
Switcher Options
DashBoard Display
SHC-9642 SDI to HDMI
Converter
SideShot
SMC-9901 Serial to MIDI
Converter
XPression
™
Live
Training Options
Online Operational Training
Onsite Commissioning
CF-116
CF-124
CF-216
CF-224
CF-116PLUS
CF-124PLUS
CF-216PLUS
CF-224PLUS
CF-1ME-2ME-UPG
PSU-12V16A-6PIN
CF-1ME-ROSSCARE
CF-2ME-ROSSCARE
CF-116MM
CF-124MM
CF-216MM
CF-224MM
CBPS-DashMenu
SHC-9642
CPS-SideShot
SMC-9901
XDS0-0001-CPS
CARBONITE-ONL-1DAY
CARBONITE-COM-1DAY
CF-224EX-16*
CF-224EX-48*
CF-224EX-96*
CF-NK-P3G
**
**
**
CF-NK-I3G
CF-NK-I3G-RC
CF-NK-O3G
CF-NK-O3G-RC
CF-EX-1STSWR-UPG
CF-EX-2NDSWR-UPG
CF-EX-REDCTRL
CBF-236
CBF-ADD-ME3
PSU-48V5.9A-4PIN
CBF-236-ROSSCARE
CBF-336-ROSSCARE
16 • Option Summary — Carbonite Configuration Guide (v11.1)
Onsite Operational Training
Onsite Technical Training
Carbonite Carbonite+ Carbonite
MultiMedia
CARBONITE-OTR-1DAY
CARBONITE-OTT-1DAY
Carbonite eXtreme Carbonite Black
Notes:
• * The switcher subsystem only supports a maximum of 24 inputs.
• ** The Carbonite eXtreme comes standard with a 5-year transferable warranty. No extended warranty is available for this frame.
Control Panel Options
Control Panel
CB1 — 1 16-Button Row
CB1S — 1 24-Button Row
CB2 — 2 16-Button Rows
CB2S — 2 24-Button Rows
CB3S — 3 24-Button Rows
CB3X — 3 32-Button Rows
Panel Option Code
CB1-PANEL
CB1S-PANEL
CB2-PANEL
CB2S-PANEL
CB3S-PANEL
CB3X-PANEL
Redundant Power, Panel
PSU-12V16A-6PIN
PSU-12V16A-6PIN
PSU-12V16A-6PIN
PSU-12V16A-6PIN
PSU-12V16A-6PIN
PSU-12V16A-6PIN
Extended Warranty, Panel
CB1-PANEL-ROSSCARE
CB1S-PANEL-ROSSCARE
CB2-PANEL-ROSSCARE
CB2S-PANEL-ROSSCARE
CB3S-PANEL-ROSSCARE
CB3X-PANEL-ROSSCARE
Carbonite Configuration Guide (v11.1) — Option Summary • 17
Panel Dimensions
These dimensions are provided as a guide only. Contact Ross Video Technical Support for scale CAD drawings of the control panels and frames.
Dimensions are in inches with metric dimensions shown in brackets [mm].
CB1
23.42 [594.9]
SELF
KEY
AUTO
SELECT
CHR
KEY DVE
ME 1
STORE
ME 1
RECALL
ME 2
STORE
ME 2
RECALL
LOCK
HOME
CC
UP
MENU
BACK
NEXT
(SHIFT)
KEY 1
SEL
KEY 2
SEL
KEY 3
SEL
KEY 4
SEL
AUX
1
AUX
2
AUX
3
AUX
4
KEY/AUX/CUSTOM CONTROL
PUSH PUSH
BANK
1
BANK
2
BANK
3
BANK
4
PUSH
TRANSITION
KEY 1
CUT
KEY 2
CUT
KEY 1
AUTO
KEY 2
AUTO
PROGRAM
PRESET
KEY 3
CUT
KEY 4
CUT
KEY 3
AUTO
KEY 4
AUTO
BKGD KEY 1 KEY 2 KEY 3 KEY 4
DISS WIPE DVE MEDIA
ROLL
CLIP CUT
AUTO
TRANS
CB1S
32.51 [825.8]
SELF
KEY
AUTO
SELECT
CHR
KEY
DVE
SHOW
ALPHA
KEY
PV
ME 1 ME 2 ME 3
MULTI
SCN 1
STORE
MiniME
1
MiniME
2
MiniME
3
MiniME
4
MULTI
SCN 2
RECALL
LOCK
HOME
CC
UP
MENU
BACK
NEXT
(SHIFT)
PUSH PUSH
KEY 1
SEL
KEY 2
SEL
KEY 3
SEL
KEY 4
SEL
AUX
1
KEY/AUX/CUSTOM CONTROL
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
AUX
7
AUX
8
PUSH
PROGRAM
PRESET
BANK
1
BANK
2
BANK
3
BANK
4
EFFECTS MEMORY
STORE 7
PGM
MEM
AI
EFF
DISS
BANK
4
1
8
5
2
9
6
3
RECALL
EFF
RATE
ME
RATE
0 ENTER
KEY
RATE
TRANSITION
KEY 1
CUT
KEY 1
AUTO
KEY 2
CUT
KEY 2
AUTO
BKGD KEY 1 KEY 2 KEY 3 KEY 4
DISS WIPE DVE MEDIA USER
KEY 3
CUT
KEY 4
CUT
KEY 3
AUTO
KEY 4
AUTO
ROLL
CLIP
CUT
AUTO
TRANS
CB2
23.42 [594.9]
SELF
KEY
AUTO
SELECT
CHR
KEY
DVE
ME 1
STORE
ME 2
STORE
ME 1
RECALL
ME 2
RECALL
LOCK
HOME
CC
UP
MENU
BACK
NEXT
(SHIFT)
KEY 1
SEL
KEY 2
SEL
KEY 3
SEL
KEY 4
SEL
AUX
1
AUX
2
KEY/AUX/CUSTOM CONTROL
AUX
3
AUX
4
PUSH PUSH
BANK
1
BANK
2
BANK
3
BANK
4
PUSH
TRANSITION 1
BKGD KEY 1 KEY 2 KEY 3 KEY 4
PROGRAM
PRESET
DISS WIPE DVE MEDIA
ROLL
CLIP
CUT AUTO
TRANS
SELF
KEY
AUTO
SELECT
CHR
KEY
DVE KEY 1
SEL
KEY 2
SEL
KEY 3
SEL
KEY 4
SEL
AUX
1
AUX
2
AUX
3
AUX
4
KEY/AUX/CUSTOM CONTROL
PROGRAM
PRESET
BANK
1
BANK
2
BANK
3
BANK
4
TRANSITION 2
KEY 1
CUT
KEY 1
AUTO
KEY 2
CUT
KEY 2
AUTO
KEY 3
CUT
KEY 4
CUT
KEY 3
AUTO
KEY 4
AUTO
BKGD KEY 1 KEY 2 KEY 3 KEY 4
DISS WIPE DVE MEDIA
ROLL
CLIP CUT
AUTO
TRANS
KEY 1
CUT
KEY 2
CUT
KEY 3
CUT
KEY 4
CUT
KEY 1
AUTO
KEY 2
AUTO
KEY 3
AUTO
KEY 4
AUTO
CB2S
32.51 [825.8]
SELF
KEY
AUTO
SELECT
CHR
KEY
DVE
SELF
KEY
AUTO
SELECT
CHR
KEY
SHOW
ALPHA
KEY
PV
ME 1 ME 2 ME 3
MULTI
SCN 1
STORE
MiniME
1
MiniME
2
MiniME
3
MiniME
4
MULTI
SCN 2
RECALL
LOCK
HOME
CC
UP
MENU
BACK
NEXT
(SHIFT)
PUSH PUSH
KEY 1
SEL
KEY 2
SEL
KEY 3
SEL
KEY 4
SEL
AUX
1
KEY/AUX/CUSTOM CONTROL
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
AUX
7
AUX
8
PUSH
BANK
1
BANK
2
BANK
3
BANK
4
EFFECTS MEMORY 1
PROGRAM
PRESET
TRANSITION 1
BKGD KEY 1 KEY 2 KEY 3 KEY 4
STORE
7
PGM
MEM
AI
EFF
DISS BANK
4
1
8
5
2
9
RECALL
6
3
EFF
RATE
ME
RATE
0
ENTER
KEY
RATE
DISS WIPE DVE MEDIA USER
ROLL
CLIP CUT
AUTO
TRANS
SHOW
ALPHA
KEY
PV
KEY 1
SEL
KEY 2
SEL
KEY 3
SEL
KEY 4
SEL
AUX
1
KEY/AUX/CUSTOM CONTROL
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
AUX
7
AUX
8
PROGRAM
PRESET
BANK
1
BANK
2
BANK
3
BANK
4
EFFECTS MEMORY 2
STORE 7
PGM
MEM
AI
4
1
EFF
DISS
BANK
8
5
2
0
9 RECALL
6 EFF
RATE
ME
RATE
3
ENTER KEY
RATE
KEY 2
CUT
KEY 3
CUT
KEY 4
CUT
TRANSITION 2
KEY 1
CUT
KEY 1
AUTO
KEY 2
AUTO
KEY 3
AUTO
KEY 4
AUTO
BKGD KEY 1 KEY 2 KEY 3 KEY 4
DISS WIPE DVE MEDIA USER
ROLL
CLIP CUT
AUTO
TRANS
KEY 1
CUT
KEY 2
CUT
KEY 3
CUT
KEY 4
CUT
KEY 1
AUTO
KEY 2
AUTO
KEY 3
AUTO
KEY 4
AUTO
18 • Panel Dimensions — Carbonite Configuration Guide (v11.1)
CB3S
CB3X
32.51 [825.7]
SELF
KEY
AUTO
SELECT
CHR
KEY
DVE SHOW
ALPHA
KEY
PV
ME 1 ME 2 ME 3
MULTI
SCN 1 STORE
MiniME
1
MiniME
2
MiniME
3
MiniME
4
MULTI
SCN 2
RECALL
LOCK
HOME
CC
UP
MENU
BACK
NEXT
(SHIFT)
PUSH PUSH
KEY 1
SEL
KEY 2
SEL
KEY 3
SEL
KEY 4
SEL
AUX
1
KEY/AUX/CUSTOM CONTROL
AUX
2
AUX
3
AUX
4
AUX
5
AUX
6
AUX
7
AUX
8
PUSH
PROGRAM
PRESET
BANK
1
BANK
2
BANK
3
BANK
4
EFFECTS MEMORY 1
STORE 7
PGM
MEM
AI
4
1
EFF
DISS
BANK
8
5
2
9
6
3
RECALL
EFF
RATE
ME
RATE
0 ENTER
KEY
RATE
TRANSITION 1
KEY 1
CUT
KEY 1
AUTO
KEY 2
CUT
KEY 3
CUT
KEY 4
CUT
KEY 2
AUTO
KEY 3
AUTO
KEY 4
AUTO
BKGD KEY 1 KEY 2 KEY 3 KEY 4
DISS WIPE DVE MEDIA USER
ROLL
CLIP
CUT
AUTO
TRANS
KEY/AUX/CUSTOM CONTROL
PROGRAM
PRESET
KEY/AUX/CUSTOM CONTROL
PROGRAM
PRESET
AUX
5
AUX
6
AUX
7
AUX
8
BANK
1
BANK
2
BANK
3
BANK
4
EFFECTS MEMORY 2 TRANSITION 2
BKGD KEY 1 KEY 2 KEY 3 KEY 4
STORE 7
PGM
MEM
AI
4
1
EFF
DISS
BANK
8
5
2
0
9 RECALL
6 EFF
RATE
ME
RATE
3
ENTER KEY
RATE
DISS WIPE DVE MEDIA USER
ROLL
CLIP
CUT
AUTO
TRANS
AUX
5
AUX
6
AUX
7
AUX
8
BANK
1
BANK
2
BANK
3
BANK
4
EFFECTS MEMORY 3
STORE 7
PGM
MEM
AI
4
1
EFF
DISS
BANK
8
5
2
9
6
3
RECALL
EFF
RATE
ME
RATE
0 ENTER
KEY
RATE
KEY 3
CUT
KEY 4
CUT
TRANSITION 3
KEY 1
CUT
KEY 1
AUTO
KEY 2
CUT
KEY 2
AUTO
KEY 3
AUTO
KEY 4
AUTO
BKGD KEY 1 KEY 2 KEY 3 KEY 4
DISS WIPE DVE MEDIA USER
ROLL
CLIP
CUT
AUTO
TRANS
KEY 1
CUT
KEY 2
CUT
KEY 3
CUT
KEY 4
CUT
KEY 1
AUTO
KEY 2
AUTO
KEY 3
AUTO
KEY 4
AUTO
38.19 [970.0]
SELF
KEY
AUTO
SELECT
CHR
KEY
DVE SHOW
ALPHA
KEY
PV
KEY 1
SEL
KEY 2
SEL
KEY 3
SEL
KEY 4
SEL
AUX
1
AUX
2
ME 1 ME 2 ME 3
MULTI
SCN 1 STORE
MiniME
1
MiniME
2
MiniME
3
MiniME
4
MULTI
SCN 2
RECALL
AUX
3
AUX
4
KEY/AUX/CUSTOM CONTROL
PROGRAM
PRESET
AUX
5
AUX
6
AUX
7
AUX
8
LOCK
HOME
CC
UP
MENU
BACK
NEXT
(SHIFT)
ME
1
ME
2
ME
3
USER
1
PUSH PUSH PUSH
BANK
1
BANK
2
BANK
3
BANK
4
BANK
5
BANK
6
BANK
7
BANK
8
EFFECTS MEMORY 1
STORE 7
PGM
MEM
AI
EFF
DISS
BANK
4
1
8
5
2
9
6
3
RECALL
EFF
RATE
ME
RATE
0 ENTER
KEY
RATE
TRANSITION 1
KEY 1
CUT
KEY 1
AUTO
KEY 2
CUT
KEY 3
CUT
KEY 4
CUT
KEY 2
AUTO
KEY 3
AUTO
KEY 4
AUTO
BKGD KEY 1 KEY 2 KEY 3 KEY 4
DISS WIPE DVE MEDIA USER
ROLL
CLIP
CUT
AUTO
TRANS
AUX
5
KEY/AUX/CUSTOM CONTROL
AUX
6
AUX
7
AUX
8
ME
1
ME
2
ME
3
USER
1
BANK
1
BANK
2
BANK
3
BANK
4
BANK
5
BANK
6
BANK
7
BANK
8
EFFECTS MEMORY 2
PROGRAM
PRESET
TRANSITION 2
BKGD KEY 1 KEY 2 KEY 3 KEY 4
STORE 7
PGM
MEM
AI
4
1
EFF
DISS
BANK
8
5
9
6
RECALL
EFF
RATE
2
0
3
ME
RATE
ENTER KEY
RATE
DISS WIPE DVE MEDIA USER
ROLL
CLIP
CUT
AUTO
TRANS
AUX
5
AUX
6
AUX
7
AUX
8
KEY/AUX/CUSTOM CONTROL
PROGRAM
PRESET
ME
1
ME
2
ME
3
USER
1
BANK
1
BANK
2
BANK
3
BANK
4
BANK
5
BANK
6
BANK
7
BANK
8
EFFECTS MEMORY 3
STORE 7
PGM
MEM
AI
EFF
DISS
BANK
4
1
8
5
2
9
6
3
RECALL
EFF
RATE
ME
RATE
0 ENTER
KEY
RATE
TRANSITION 3
KEY 1
CUT
KEY 1
AUTO
KEY 2
CUT
KEY 2
AUTO
KEY 3
CUT
KEY 4
CUT
KEY 3
AUTO
KEY 4
AUTO
BKGD KEY 1 KEY 2 KEY 3 KEY 4
DISS WIPE DVE MEDIA USER
ROLL
CLIP
CUT
AUTO
TRANS
KEY 1
CUT
KEY 2
CUT
KEY 3
CUT
KEY 4
CUT
KEY 1
AUTO
KEY 2
AUTO
KEY 3
AUTO
KEY 4
AUTO
Carbonite Configuration Guide (v11.1) — Panel Dimensions • 19
Frame Dimensions
Dimensions are in inches with metric dimensions shown in brackets [mm].
Carbonite Frame
18.93
[480.82]
16.82
[427.23]
Y
Pb
Pr
1
INPUTS
PS 1
2
3
LTC
PS 2
4
HDMI
5
TALL
Y
6
GPIO
Pb
Pr
HDMI
Y
24
22
23
Y
Pb
Pr
HDMI
7
Y
Pb
Pr
HDMI
8
PSL
9
10
11
2
1
1
SERIAL OUTPUTS
12
13
2
3
14
15
4
5
16
17
6
7
18
19
8
20
21
PV
PGM
OUT1
OUT2
IN
REF
17.45
[443.23]
3.50
[88.9]
Carbonite eXtreme Frame
1
2
VID REF
T-BUS
ALARM
17.50
[444.50]
1
1
2
2
18.93
[480.82]
12.60
[320.04]
Carbonite Black Frame
18.93
[480.8]
17.21
[437.1]
20
21
19
IN
1
PS2
2
3
22
23
Y
GPIO
5
PS1 LTC
31
32
29
30
24
25
26
8
PANEL
9
10
2
11
6
7
27
28
1
OUT
1
12
2
13
14
3
AES
1 2
SERIAL
33
34
15
16
4
5
6
35
36
17
18
17.46
[443.4]
7
8
19
20
17
18
11
12
13
14
OUT
9
10
OUT1
OUT2
21
22
15
16
IN
REF
3.44
[87.4]
20 • Frame Dimensions — Carbonite Configuration Guide (v11.1)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project