Operating Instructions
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at
the sun or other extremely bright objects. Otherwise, blooming or smear may be caused.
Operating Instructions
1. Camera Identification (CAMERA ID) Setting
1. CAMERA SETUP MENU
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings.
Use the camera at temperatures within –30 °C to +50 °C (–22 °F - 122 °F), and humidity below
90 %. The input power source is 12 V DC or 24 V AC 60 Hz.
You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera
ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off
on the monitor screen.
This camera utilizes an on-screen user setup menu.
• Opening the Setup Menu
8. Turn the circuit breaker off which supplies the camera with the power when abnormal
conditions are encountered.
To edit the CAMERA ID
1. Move the cursor to CAMERA ID.
** CAM SET UP **
CAMERA ID
OFF
ALC
ALC
SHUTTER
--AGC
ON(HIGH)
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
LED
ON
DIP SW
END
SET UP DISABLE
Press and hold down I(S) for 2 seconds or
more.
The factory default setting is OFF.
↵
II
SD
Color CCTV Cameras
SETTING PROCEDURES
↵↵
74
W3
-C
WV
SETUP
Caution:
Connect to 12 V DC (10.5 V-16 V) or 24 V AC 60 Hz (19.5 V-28 V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the
power is supplied from a 24 V AC 60 Hz power source.
!3
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Refer to the following sections for a detailed description of menu items. If you decide not to make
any changes after checking the current settings, move the cursor to END in the bottom line, and
press I(S) to close the setup menu.
!3 Power cable (for camera/heater)
N0404-0
Caution:
Before attempting to connect or operate this
product, please read the marking on the top.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SA 1965
SA 1966
The lightning flash with arrowhead
symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
3TR002483AAA
Printed in Japan
For U.S.A
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables when
connecting to computer or peripheral devices). Any
changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate this equipment.
The serial number of this product may be found on
the top of the unit.
You should note the serial number of this unit in the
space provided and retain this instruction as a permanent record of your purchase to aid identification
in the event of theft.
FEATURES
Brown (Live)
Blue (Neutral)
1. The following functions are built in.
(1) Auto Light Control (ALC)
(2) The SUPER-D2 function eliminates interference by strong background lighting which
makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB (Typical)
(3) Internal, Line-Locked, Multiplexed Vertical Drive (VD2) Sync
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)
3. Minimum illumination of 1.0 lx (0.10 footcandle) (WIDE) (Color mode)
Minimum illumination of 0.15 lx (0.015 footcandle) (WIDE) (Black-and-white mode)
4. 480 lines of horizontal resolution (Color normal mode)
510 lines of horizontal resolution (Color High Resolution mode)
570 lines of horizontal resolution (Black-and-white mode)
5. High quality picture:
(a) 2H type vertical enhancer for greater picture sharpness
(b) Chroma averaging circuit for better color signal-to-noise ratio
(c) Minimum of aliasing on fine objects
(d) Expanded dynamic range by use of knee circuit
(e) Highlight aperture correction for greater picture detail of bright objects
6. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF
7. Built-in Digital Motion Detector (when the motion detector is enabled, the LEDs on both sides of
camera blink.)
8. Auto black-and-white mode enables the camera to switch between color and black-and-white
picture in response to Light input.
9. Electronic zoom function magnifies a scene 2-fold and changes the angle of view.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
Model No.
Serial No.
q
for camera
Note: If no button is pressed for 5 minutes while a setup menu is being displayed on the monitor
screen, it is automatically closed and the mode returns to the normal camera picture.
Green/Yellow (GND)
Black (Live)
Gray (Neutral)
for heater
Caution: For camera
Connect to 12 V DC (10.5-16 V) or 24 V AC 60 Hz (19.5 V-28 V) class 2 power supply only.
Make sure to connect the grounding lead to the GND terminal when the power is supplied
from a 24 V AC 60 Hz power source.
Caution: For heater
Connect to 24 V AC 60 Hz (19.5 V-28 V) class 2 power supply only.
!4 Video output cable with BNC connector
Connects with the video connector of the monitor.
2. SETUP OPERATION
This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM SET
UP menu, use the following buttons on the back.
Left Button (I) (L):
Moves the cursor to the left. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button
is pressed.
Right Button (I) (R): Moves the cursor to the right. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button
is pressed.
Moves the cursor upwards. Use this button to select an item or adjust the
Up Button (I) (U):
parameters.
Down Button (I) (D): Moves the cursor downwards. Use this button to select an item or adjust
the parameters.
Executes selections and displays a submenu for an item with the
Set Button (I) (S):
mark.
• To reset the parameter to the factory default setting, move the cursor to the parameter to be
reset and press I(L) and I(R) simultaneously.
• To return to the previous menu or page, move the cursor to RET and press I(S).
• To close the setup menu, move the cursor to END and press I(S).
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are unsure
about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both I(L) and I(R), press I(S) for a few seconds. The message ALL
RESET momentarily appears on the monitor screen.
This resets all adjustments and parameters to the factory default settings except for the PIX
OFF setting.
• Editing the CAM SET UP Menu
5
6
4 BW
5 BW AUTO
LEVEL
6 LED
LL
OFF
ON
SHARP SOFT
OFF
AUTO
LOW
HIGH
OFF
ON
!2
q LEFT Button
Moves the cursor to the left and selects items in the CAM SETUP menu.
w UP Button
Moves the cursor upward and selects items in the CAM SETUP menu.
PREFACE
Panasonic's WV-CW374 color digital camera introduces a new level of high picture quality and high
resolution through the use of a 1/3-inch interline transfer CCD image sensor having 768 horizontal
pixels (picture elements), and digital signal processing LSIs. This model offers cutting-edge technology for advanced video surveillance.
PRECAUTIONS
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside. Ask qualified service personnel for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by
improper handling or storage.
3. The installation should be made by qualified service personnel or system installers.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty. When the dirt is hard to remove, use a mild
detergent and wipe gently. Then wipe off the remaining detergent with a dry cloth.
5. Clean the lens with care.
Do not clean the lens with strong or abrasive detergents. Use lens tissue or a cotton tipped
applicator and ethanol.
To edit the CAM SET UP menu (change settings), press I(U) and I(D) or I(L) and I(R) to
move the cursor to SET UP DISABLE in the bottom line.
** CAM SET UP **
** CAM SET UP **
CAMERA ID
OFF
CAMERA ID
OFF
Press I(S). SETUP DISABLE changes to
ALC
ALC
ALC
ALC
SHUTTER
--SHUTTER
--SETUP ENABLE. Move the cursor to DIP SW.
AGC
ON(HIGH)
AGC
ON(HIGH)
SENS UP
OFF
SENS UP
OFF
Press I(S). DIP SW changes to MENU. Then
SYNC
INT
SYNC
INT
WHITE BAL
ATW1
WHITE BAL
ATW1
move the cursor to the item(s) you want to
MOTION DET
OFF
MOTION DET
OFF
LED
ON
LED
ON
change.
DIP SW
MENU
e RIGHT Button
Moves the cursor to the right and selects items in the CAM SETUP menu.
↵
4
2 UPSIDE
DOWN
3 AP GAIN
INT
↵↵
3
1 SYNC
END
SET UP DISABLE
↵
2
y
u
i
o
!0
!1
↵↵
ON
1
↵
w
e
r
t
Important Notice:
When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannot
change the currently active settings. This is to prevent accidental changing of the settings.
↵
WARNING: All work related to the installation of this product should be made by qualified service personnel or
system installers.
END
Character Cursor
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$
3. Move the cursor to the character you want to edit
by pressing I(L) / I(R) / I(U) / I(D).
↵
WV-CW374
The CAM SET UP menu appears on the monitor as
shown at right.
Check the current settings on the menu.
↵
Model No.
!4
2. Press I(S). The CAMERA ID menu appears.
The cursor on the letter “0” is highlighted.
SET UP ENABLE
Notes:
• When DIP SW is selected for CAM SET UP menu, six modes can be set with the DIP switches.
• To operate the camera functions with the system controller, select MENU in the CAM SET UP
menu.
4. After selecting the character, press I(S). The
selected character appears in the editing area.
(The pointer in the editing area moves to the right
automatically at this moment.)
5. Repeat the steps above until all characters are
edited.
Character
Area
SPACE
POSI RET END RESET
Command
................
Editing
Area
Pointer
CAMERA ID menu
To enter a blank space in the CAMERA ID
Move the cursor to SPACE and press I(S).
To replace a specific character in the CAMERA ID
1. Move the cursor to the editing area by pressing I(D).
2. Move the pointer to the character to be replaced by pressing I(L) or I(R). Then move the
cursor to the character area and select a new character.
3. Press I(S) to determine the CAMERA ID.
To erase all characters in the editing area
Move the cursor to RESET and press I(S). All characters in the editing area disappear.
To determine the display position of the CAMERA ID
1. Move the cursor to POSI, and press I(S). The display at right appears and the CAMERA ID
is highlighted.
2. Move the CAMERA ID to the desired position by
Highlighted
pressing I(L) / I(R) / I(U) / I(D).
3. Press I(S) to fix the position of the CAMERA
ID. The mode returns to the previous CAMERA ID
menu.
WV-CW374
Notes:
• The CAMERA ID stops at the edges of the
monitor screen.
• The CAMERA ID moves faster if any of I(L) / I(R) / I(U) / I(D) is kept pressed
for a second or more.
2. Light Control Setting (ALC)
2-1. ALC Mode with SUPER-D2 ON
Super Dynamic2 Function (SUPER-D2)
The important object in a scene is usually placed in the center of the monitor screen. In the SUPERD2 mode, more photometric weight is given to the center of the screen (where the important object
is located) than to the edge of the screen (where a bright backlight would most likely be located).
The SUPER-D2 function eliminates interference by strong background lighting which makes the
camera picture dark, such as a spotlight.
1. Move the cursor to ALC and press I(S). The ALC CONT menu appears.
2. Move the cursor to SUPER-D2 and select ON.
3. If you want to adjust the video output level,
move the "I" cursor for LEVEL. Adjust to the
desired level by pressing I(L) or I(R).
** ALC CONT **
BACK LIGHT COMP
SUPER-D2
ON
LEVEL
RET
...I.....
+
END
Important Notice:
When the setup menu is closed after changing the parameters in the menu, the new values are
stored in the EEPROM (Electrically Erasable and Programmable Read-Only Memory). These
values remain valid until new values are stored, even if the power of the camera is off.
r Set Button
This button is used to activate an item selected in the CAM SETUP menu.
t DOWN Button
Moves the cursor downward and selects items in the CAM SETUP menu.
y SYNC switch (SW1)
Switches internal sync (INT) mode or line-lock (LL) mode. The factory default setting is INT.
u UPSIDE DOWN switch (SW2)
Turn the picture upside down by selecting ON. The factory default setting is OFF.
i AP GAIN switch (SW3)
Selects the aperture gain level to SHARP or SOFT. The factory setting is SHARP.
o BW switch (SW4)
Switches to AUTO between color and black -and-white picture in response to light input. The
factory default setting is OFF.
!0 BW AUTO LEVEL switch (SW5)
Selects the illuminance level in LOW or HIGH mode for B/W. The factory default setting is HIGH.
!1 LED ON/OFF switch (SW6)
The factory default setting is ON.
!2 Monitor output Jack (3.5 Diam. Mini jack)
Connects the LCD monitor and such devices with 3.5 mm in diam. 2-pole plug for checking
images.
(To be continued reverse page)
SETTING PROCEDURES
SPECIFICATIONS
The preset values for SENS UP (electronic sensitivity enhancement) change by pressing I(L) or
I(R) as shown right:
2-2. ALC Mode with SUPER-D2 OFF
1. Move the cursor to SUPER-D2 and select OFF.
The MASK SET appears on the menu.
OFF
** ALC CONT **
BACK LIGHT COMP
MASK SET
2. Move the cursor to MASK SET and press
I(S). The 48 mask areas appear on the
monitor screen. The cursor is blinking in the
upper left corner of the screen.
X16 FIX
X10 FIX
X6 AUTO
X6 FIX
X10 AUTO
X4 FIX
OFF
X2 FIX
AWC
R
**
....I....
+
....I....
+
B
Notes:
• When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this item.
• When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has priority
so that the SUPER-D2 function is not activated automatically.
• While the SENS UP function is selected, noise, spots or a whitish phenomenon may appear in
the picture when the sensitivity of the camera is increased. This is a normal phenomenon.
...I.....
+
END
RET
END
You can set the white balance items manually.
1. Move the cursor to R.
2. Press I(L) or I(R) to obtain the optimum amount of red gain.
3. Move the cursor to B.
4. Press I(L) or I(R) to obtain the optimum amount of blue gain.
1. Move the cursor to MOTION DET and select
ON.
The factory default setting is OFF.
2. Press I(S). The MOTION DETECT menu
appears on the monitor screen.
** MOTION DETECT **
LEVEL
ALARM
MASK SET
6-1. Line-lock Sync Mode (LL)
Note: If ON is selected for SUPER-D2, a shadow
(black line) may appear at the boundary
between the bright and the dim scene. This is
a natural phenomenon and does not indicate trouble.
3. Shutter Speed Setting (SHUTTER)
Note: To select electronic shutter speed, select OFF for SUPER-D2 in the ALC CONT menu.
Move the cursor to SHUTTER and select the electronic shutter speed.
The preset values for SHUTTER (electronic shutter speed) change by pressing I(L) or I(R) as
follows:
The factory default setting is ---.
Note: When SUPER D2 is set to ON, a dotted line appears for the shutter speed, and you cannot
select it.
OFF
1/100
1/250
1/500
1/4000
1/2000
1/1000
4. Gain Control Setting
You can set the gain (brightness level portion of an image) to automatic level adjustment.
Move the cursor to AGC and select automatic level adjustment [AGC ON (LOW, MID, HIGH)/OFF
(fixed level)].
↵↵
** CAM SET UP **
CAMERA ID
OFF
ALC
ALC
SHUTTER
--AGC
ON(HIGH)
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
LED
ON
MENU
END
SET UP ENABLE
LOW: DNR level is low.
HIGH: DNR level is high.
The factory default setting is HIGH.
RET
END
You can select one of three modes for white balance adjustment as follows:
The factory default setting is ATW1.
• ATW1 (Auto-Tracing White Balance 1)
Move the cursor to WHITE BAL and select ATW1.
In this mode, the color temperature is monitored continuously and thereby white balance is
automatically set. The color temperature range for the proper white balance is approximately 2
600 - 6 000K. Proper white balance may not be
obtained under the following conditions:
** CAM SET UP **
1. The color temperature is out of the 2 600 CAMERA ID
OFF
6 000K range.
ALC
ALC
SHUTTER
--2. When the scene contains mostly high
AGC
ON(HIGH)
SENS UP
OFF
color temperature objects, such as a blue
SYNC
INT
WHITE BAL
ATW1
sky or sunset.
MOTION DET
OFF
3. When the scene is dim.
LED
ON
MENU
In these cases, select the AWC mode.
END
SET UP ENABLE
• ATW2 (Auto-Tracing White Balance 2)
Auto-tracing white balance in sodium light mode (ATW2)
When that you select ATW2 for sodium light, white balance is set automatically (no operation
needed).
Note: ATW1 and ATW2 do not appear for WHITE BAL on the system controller setup menu.
Move the cursor to SENS UP and select the parameter for electronic sensitivity enhancement.
Move the cursor to LED and select ON or OFF using I(L) or I(R).
ON: LED lighting up
OFF: LED lighting out
Default: ON
Note: When stopping LED blinking at the motion detector enabled, select OFF for LED setting.
2. Press I(S) to start the white balance setup.
The PUSH SW is highlighted to indicate that
the white balance is being set.
3. When the white balance setting is completed,
the PUSH SW returns to normal display.
Note: If white balance is not set, the PUSH SW
is being highlighted.
4*
8
Video Output:
Horizontal Resolution:
Signal-to-Noise Ratio:
Dynamic Range:
Minimum Illumination:
000 000
RET END
** EL-ZOOM **
PAN/TILT
ZOOM
→PUSH SET
→PUSH SET
+
U TILT D/L PAN R
RET END
** EL-ZOOM **
PAN/TILT
ZOOM
→PUSH SET
→PUSH SET
U ZOOM D
The blemish compensation position setting screen appears, and press I(L) and I(R)
simultaneously for 2 seconds or more.
The screen is restored to the PIX OFF menu, the blemish compensation position is deleted and
"*" is also deleted from the right of the number.
Gain Control:
White Balance:
Aperture:
Super Dynamic2:
Electronic Shutter Speed:
Lens
Focal length:
Maximum aperture ratio:
Angular field of view:
Focusing range:
Ambient Operating Temperature:
Ambient Operating Humidity:
Power Source and
Power Consumption:
Ingress Protection (Camera Unit):
Dimensions
Weights:
RET END
5 mm - 40 mm
1:1.6 (Wide), 1:1.9 (Tele)
Horizontal: 6.6 ° - 52 °
Vertical:
5.0 ° - 39.6 °
1.2 m - ∞ (3.9 ft - ∞)
–30 °C - +50 °C (–22 °F - 122 °F)
Less than 90 %
For camera
24 V AC 60 Hz, 3.8 W
12 V DC 367 mA
For heater
24 V AC 60 Hz, 12 W
IP66. NEMA 4X
78 mm (H) x 82 mm (W) x 301 mm (L)
3-1/16” (H) 3-1/4” (W) 11-7/8” (L)
1.3 kg (2.9 lbs.)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
10-8 Black and White Mode (BW MODE)
Move the cursor to BW MODE and press I(S). The BW MODE menu appears. You can set
up the BW mode on this menu.
BW Setting
1. Move the cursor to BW and select AUTO, ON
** BW MODE **
or OFF using I(L) or I(R). Factory default
BW
OFF
setting: OFF.
AUTO: The camera selects black and white
PIX SENS UP
OFF
mode if the picture is dark, or color mode if
BURST(BW)
ON
the picture is bright enough.
ON: The black and white mode is selected.
RET END
OFF: The color mode is selected.
2. If you have selected AUTO the LEVEL and the DURATION TIME appear on the menu.
3. Select HIGH or LOW for the threshold level at which the camera automatically switches to BW
or color mode. Default: HIGH
The illuminance shown below is based on the assumption that the camera is used in an area lit
by halogen lamps, and that AGC on the menu is set to MID.
Note: When near-infrared lamps are used, the image may be displayed out of focus and mode
switching may not perform automatically.
4. Move the I cursor to set DURATION TIME. Default: 30 seconds
The camera determines whether to switch the mode when the time set for holding a picture
motionless on the screen has elapsed.
Available duration times: (S) 10 s ↔ 30 s ↔ 60 s ↔ 300 s (L)
Move the cursor to PIX SENS UP and select
OFF or X2 AUTO.
10. Special Menu
This menu lets you adjust and set up the video
signal of the camera to meet your requirements.
Move the cursor to END in the bottom line of
the CAM SET UP menu and press I(L) and
I(R) simultaneously (holding down I(L)
and press I(R)) for 2 seconds or more. The
SPECIAL menu appears on the monitor screen.
** CAM SET UP **
CAMERA ID
OFF
ALC
ALC
SHUTTER
--AGC
ON(HIGH)
SENS UP
OFF
SYNC
INT
WHITE BAL
ATW1
MOTION DET
OFF
LED
ON
MENU
END
SET UP ENABLE
STANDARD ACCESSORIES
Operating Instructions (this document) ............................................. 1 pc.
Instructions ........................................................................................ 1 pc.
The following are for installation.
Sun shield .......................................................................................... 1 pc.
Mounting arm .................................................................................... 1 pc.
Adapter box ....................................................................................... 1 pc.
Mount adapter ................................................................................... 1 pc.
Cover ................................................................................................. 2 pcs.
** CAM SET UP **
CAMERA ID
OFF
ALC
ALC
SHUTTER
--AGC
ON(HIGH)
SENS UP
OFF
SYNC
INT
WHITE BAL
AWC→PUSH SW
MOTION DET
OFF
LED
ON
MENU
END
SET UP ENABLE
Highlighted
** BW MODE **
** SPECIAL **
UP SIDE DOWN OFF
CHROMA GAIN -....I....+
AP SHARP
-...I.....+
PEDESTAL
-......I..+
HUE
-....I....+
BW
AUTO
LEVEL
HIGH
DURATION TIME •|••
S L
PIX SENS UP
OFF
BURST(BW)
ON
RESOLUTION
NORMAL
EL-ZOOM
OFF
BW MODE
PIX OFF
CAMERA RESET PUSH SW
RET END
RET END
10-1. Camera Picture Upside Down Positioning (UP SIDE DOWN)
1. Move the cursor to UP SIDE DOWN.
2. Select ON when you want to turn the picture upside down.
10-2. Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to CHROMA GAIN.
2. While observing the vectorscope or color video monitor, move the “I” cursor to adjust the chroma level.
10-3. Aperture Gain Setting (AP SHARP/AP SOFT)
1. Move the cursor to AP SHARP.
2. To select AP SOFT, press I(S).
3. While observing the waveform monitor or color video monitor, move the “I” cursor to adjust the
aperture gain level.
↵
1. Move the cursor to WHITE BAL and select
AWC → PUSH SW.
↵↵
There are two modes for SENS UP.
AUTO: If you select X10 AUTO, for example, the sensitivity is automatically raised to X10 max.
When AUTO is selected, AGC is automatically set to ON.
FIX: If you select X32 FIX, for example, the sensitivity is raised to just X32.
The factory default setting is OFF.
9. LED Setting
1. Move the cursor to EL-ZOOM.
2. Select ON or OFF using I(L) or I(R).
The factory default setting is OFF.
ON: x2 electronic zoom is available.
OFF: The electronic zoom function is disabled.
3. While the cursor is on EL-ZOOM, press I(S).
The EL-ZOOM setting menu appears.
4. Move the cursor to PUSH SET for ZOOM and
press I(S) to display the ZOOM setting
menu.
5. Press I(U) or I(D) to zoom in or out the
image.
6. Move the cursor to PUSH SET for PAN/TILT
and press I(S). The PAN/TILT setting menu
appears.
7. Press I(U) or I(D) I(L) or I(R) to
change the angular field of view.
8. To return to the EL-ZOOM setting menu, press
I(S).
3*
7*
Scanning:
Horizontal:
Vertical:
Synchronization:
768 (H) x 494 (V) pixels, Interline Transfer CCD
4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pickup tube)
525 lines/60 fields/30 frames
15.734 kHz
59.94 Hz
Internal, Line-locked or Multiplexed vertical drive (VD2) Sync
selectable
1.0 V[P-P] NTSC composite 75 Ω/BNC connector
480 lines (C/L Normal), 510 line (C/L, HIGH), 570 lines (B/W)
50 dB (Equivalent to AGC Off, weight On, AP On)
46 dB (Typ)
1.0 lx (0.10 footcandle) (WIDE) (C/L),
0.15 lx (0.015 footcandle) (WIDE) (B/W)
ON (HIGH, MID, LOW)/OFF selectable
ATW1, ATW2 or AWC (SET UP MENU) selectable
Set Variable (SET UP MENU)
ON or OFF (SET UP MENU) selectable
OFF, 1/100, 1/250, 1/500, 1/1 000,1/2 000,
1/4 000, 1/10 000 s selectable
10-9 PIX SENS UP Setting
7-1. Auto-Tracing White Balance Mode (ATW)
• Automatic White Balance Control Mode (AWC)
In this mode, accurate white balance is obtained within a color temperature range of approximately 2 300-10 000K.
5. Electronic Sensitivity Enhancement (SENS UP)
Notes:
• When the motion detector is enabled, the LEDs on both sides of camera blink.
• Masking or adjusting the detection level is needed to prevent malfunction under the following
conditions:
• When shooting an object under flickering fluorescent light.
• When leaves or curtains etc. are swayed by the wind.
• When the object is lighted by lighting equipment that constantly turns on and off.
• It takes about 0.2 seconds for the alarm signal to reach the alarm terminal of the VTR after the
camera detects the object.
Because the alarm signal is multiplexed on the video signal, it may be mistakenly interpreted
by other video equipment as a time code signal.
Therefore, when the camera is not used in a Panasonic Intelligent CCTV System, select OFF to
prevent the above from occurring.
• The camera will deactivate the detector for a few minutes after the power of the camera is
turned on or the BW setting in the Special Menu is set to something other than OFF.
• The motion detection function is not designed specifically for prevention of theft, fire, etc.
↵
• Digital Noise Reduction (DNR)
DNR may be used to improve quality under low light conditions. There are 2 levels of DNR,
which may be selected depending on local site conditions.
You may need to try different settings to find
the most suitable conditions for your applica** AGC **
tion.
DNR
HIGH
Move the cursor to DNR and select LOW or
HIGH.
3. Move the cursor to MASK SET and press I(S). MASK SET lets you set 48 mask areas. To set
MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2 OFF”.
4. Move the cursor to ALARM and select ON or OFF to set the alarm for DISPLAY MODE.
Note: When using the WV-RM70, WV-CU550C series, WV-CU161C or WV-CU360C controller
with this model, select OFF for ALARM.
5. Move the cursor to DISPLAY MODE and press I(S) to see the current setting. The masks
that detect the brightness changes start blinking.
6. To raise detection sensitivity, press I(S) to return to the MOTION DETECT menu.
7. To obtain the optimum detection level, move the “I” cursor to adjust the level.
8. Repeat the procedures above to obtain a satisfactory setting.
↵↵
Note: Even if AGC is set to ON and if the noise reduction function is enabled, afterimages may
be produced by shooting a moving object.
END
7. White Balance Setting (WHITE BAL)
↵
↵
↵
• Gain Control [AGC ON (LOW/ MID/ HIGH)/OFF]
Move the cursor to AGC and select ON (LOW),
ON (MID), ON (HIGH) or OFF.
The factory default setting is ON (HIGH).
RET
OFF
↵↵
Blinking
1. Move the cursor to SYNC and select LL.
Note: The settings in this menu can be made
** SYNC **
only when the multiplexed vertical drive
V PHASE
signal (VD2) is not supplied to the camera.
COARSE
1(1--16)
2. After confirming that the cursor is on LL, press
FINE
I........
I(S). The vertical phase adjustment menu
+
appears on the monitor screen.
RET END
3. Supply the video output signal of the camera
to be adjusted and the reference camera video
output signal to a dual-trace oscilloscope.
4. Set the oscilloscope to the vertical rate and expand the vertical sync portion on the oscilloscope.
5. Move the cursor to COARSE. The cursor is
highlighted.
6. Press I(L) or I(R) to match the vertical
1 (1 - - 16): 0 degrees
phase for both video output signals as closely
2 (1 - - 16): 22.5 degrees
as possible. (COARSE adjustment can be
incremented in 16 steps by 22.5 degrees by
pressing I(L) or I(R).)
16 (1 - - 16): 337.5 degrees
Note: After the sixteenth step, the adjustment
returns to the first step.
7. Move the cursor to FINE.
8. Press I(L) or I(R) to match the vertical phase for both video output signals as closely as
possible.
(FINE adjustment can be made by up to 22.5 degrees by pressing I(L) or I(R).)
Notes:
• When the “I” cursor reaches the “+” end, it jumps back to “–”. At the same time, COARSE
is incremented by one step to enable a continuous adjustment. The reverse takes place
when the “I” cursor reaches the “–” end.
• When I(L) or I(R) is kept pressed for a second or more, the “I” cursor moves faster.
• To reset COARSE and FINE to the values preset at the factory, press I(L) and I(R)
simultaneously. COARSE and FINE adjustments are preset at the factory to zero-crossing
of the AC line phase.
• If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of the
camera video output signal may be disturbed.
• The input power source is AC only.
↵↵
Turns to white
........I
+
DISPLAY MODE
↵
Blinking
The motion detector detects the moving objects in the scene by monitoring changes in brightness
level. You can select the level of sensitivity for motion detection.
When this camera is connected to a compatible intelligent CCTV system, the camera transmits an
alarm signal by multiplexing it with the video signal.
↵
Important Notices:
1. The priority for the sync modes is as follows:
(1) Multiplexed Vertical Drive (VD2) (Highest priority)
(2) Line-lock (LL)
(3) Internal Sync (INT) (Lowest priority)
2. The line-lock mode has a submenu for line-lock vertical phase adjustment. If the camera installation is relocated, check the vertical phase adjustment again since the AC line phase may be
different.
8. Motion Detector Setting (MOTION DET)
↵
3. Move the cursor to the area where backlight is
bright and press I(S) to mask that area. The
mask turns to white. (When the cursor is
moved on an area that has already been
masked, the mask and cursor start blinking.)
↵
You can select internal sync (INT) mode, line-lock (LL) mode or the VD2 signal (multiplexed vertical
drive signal) mode.
2*
6*
2. Select a number and press I(S). The blemish compensation position setting screen appears.
Press I(L), I(R), I(U) or I(D) to place the "+" cursor on the blemish position. After
moving the "+" cursor to a position where the blemish looks inconspicuous, press I(S).
Consequently, the blemish compensation position is set up and the PIX OFF menu is restored.
After a blemish compensation position is set up, "*" is attached at the right of the number.
3. If you would like to delete a blemish compensation position, move the cursor to the applicable
number and press I(S).
10-7 Electronic Zoom (EL-ZOOM)
6. Synchronization Setting (SYNC)
1/10000
1*
5*
1. Move the cursor to RESOLUTION.
2. For high resolution display, select HIGH.
NORMAL: Sets the horizontal resolution to more than 480 lines.
HIGH: Sets the horizontal resolution to more than 510 lines.
Note: After selecting HIGH, noise may increase when the SENS UP function is activated under
low illumination.
Manual Fine Adjustment for AWC/ATW
Pick-up Device:
Scanning Area:
• PIX OFF Setting (PIX OFF)
In this setting, you can assign a blemish position and compensate the blemish.
1. Move the cursor to PIX OFF and press I(S). The PIX OFF menu appears.
** PIX OFF **
10-6 Resolution Setting
Blinking
4. Repeat step 3 to mask the desired area. To
cancel masking, move the cursor to that area
and press I(S).
5. After masking is completed, press I(S) for 2
seconds or more. The ALC CONT menu
appears.
6. If you want to change the video output level
(picture contrast), move the “I” cursor for
LEVEL and adjust the level.
1. Move the cursor to HUE.
2. While observing the vectorscope or color video monitor, move the “I” cursor to adjust the hue
(chroma phase) level.
OFF
LEVEL
RET
X32 FIX
X4 AUTO
10-5. Chroma Phase Setting (HUE)
**
↵
SUPER-D2
X2 AUTO
4. When you want to adjust the white balance
manually, press I(R) to select AWC and
press I(S). The AWC menu appears on the
monitor screen. (When ATW is selected, pressing I(S) displays the ATW menu.)
10-4. Pedestal Level Setting (PEDESTAL)
1. Move the cursor to PEDESTAL.
2. While observing the waveform monitor or color video monitor, move the “I” cursor to adjust the
pedestal level (black level).
X2 AUTO: Sensitivity will be automatically doubled at the maximum in the black and white
mode.
OFF: Sensitivity will not be enhanced.
Notes:
• "X2 AUTO" is not available when AGC is set to OFF. "X2 AUTO" is automatically set to OFF.
• When the picture becomes stable, the luminance may change for a moment.
10-10 BURST (BW) Setting
Move the cursor to BURST (BW) and select ON or OFF. Default: ON.
ON: The burst signal is supplied along with the black and white composite video.
OFF: The burst signal is not output.
Notes:
• Selecting ON is recommended for usual cases including when synchronizing the camera
to peripheral components.
• When storing images to a recorder, try both ON and OFF, then select either one suitable
for the recorder. Synchronization characteristics depend on the recorder.
To reset to the factory settings (CAMERA RESET)
1. Move the cursor to CAMERA RESET. The PUSH SW is highlighted.
2. While holding down I(L) and I(R), press I(S) for 2 seconds or more. The camera is
reset to the factory settings except for PIX OFF setting.
Panasonic Digital Communications & Security Company
Unit of Matsushita Electric Corporation of America
Security Systems Group
www.panasonic.com/cctv
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
2004
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
P.R. 00985 (809)750-4300
© Matsushita Electric Industrial Co., Ltd. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement