WinCC: Communication

WinCC: Communication
Process communication
1
Allen Bradley - Ethernet IP
2
Mitsubishi Ethernet
3
Modbus TCPIP
4
OPC Channel
5
PROFIBUS FMS
6
S5 Ethernet Layer 4
7
S5 PROFIBUS FDL
8
S5 Programmers Port AS511
9
SIMATIC HMI
WinCC V7.2
WinCC: Communication
System Manual
Print of the Online Help
02/2013
A5E32318638-AA
S5 Serial 3964R
10
SIMATIC S7 Protocol Suite
11
SIMATIC S7-1200, S7-1500
Channel
12
SIMATIC TI Ethernet Layer 4
13
SIMATIC TI Serial
14
SIMOTION
15
System Info
16
Communication - Diagnostics
17
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E32318638-AA
Ⓟ 02/2013 Technical data subject to change
Copyright © Siemens AG 2013.
All rights reserved
Table of contents
1
2
3
Process communication..............................................................................................................................13
1.1
Communication Basics................................................................................................................13
1.2
Basic Rules for Configuring Connections....................................................................................14
1.3
1.3.1
1.3.2
1.3.3
1.3.3.1
1.3.3.2
1.3.3.3
1.3.3.4
1.3.3.5
1.3.3.6
1.3.3.7
1.3.4
WinCC process communication..................................................................................................15
WinCC process communication..................................................................................................15
Principle of WinCC communication.............................................................................................15
External tags................................................................................................................................17
External tags................................................................................................................................17
How to Create a New Connection...............................................................................................19
An external tag is configured as follows......................................................................................20
Format adaptation sorted by WinCC data type...........................................................................22
Format adaptation sorted by AS data type..................................................................................28
Principle of the BinWrite-Mechanism...........................................................................................36
How to Configure a Tag with "BinWrite"......................................................................................38
Port Addresses for Coupling via Ethernet...................................................................................40
Allen Bradley - Ethernet IP.........................................................................................................................41
2.1
WinCC Channel "Allen Bradley - Ethernet IP".............................................................................41
2.2
Channel Unit Assignment............................................................................................................42
2.3
Supported Data Types.................................................................................................................43
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.6
2.4.6.1
2.4.6.2
2.4.6.3
2.4.6.4
2.4.6.5
2.4.6.6
2.4.6.7
2.4.6.8
2.4.6.9
2.4.6.10
Configuring the Channel..............................................................................................................44
Configuring the Channel "Allen Bradley - Ethernet IP"................................................................44
How to configure a "Allen Bradley E/IP PLC5" channel unit connection.....................................45
How to configure an "Allen Bradley E/IP SLC50x" channel unit connection...............................46
How to configure an "Allen Bradley E/IP ControlLogix" channel unit connection........................47
Examples: Communication path .................................................................................................47
Configuring the tags....................................................................................................................48
Configuring the tags....................................................................................................................48
Addressing...................................................................................................................................49
Addressing syntax.......................................................................................................................51
Addressing Types........................................................................................................................51
Examples for Addressing.............................................................................................................52
How to configure a tag for the Allen Bradley E/IP ControlLogix channel unit..............................53
How to configure a tag with bit by bit access for Allen Bradley E/IP PLC5 or SLC50x...............54
How to configure a tag with byte by byte access for Allen Bradley E/IP PLC5 or SLC50x.........55
How to configure a tag with word by word access for Allen Bradley E/IP PLC5 or SLC50x.......56
How to configure a text tag for Allen Bradley E/IP PLC5 or SLC50x...........................................57
Mitsubishi Ethernet.....................................................................................................................................59
3.1
WinCC channel "Mitsubishi Ethernet".........................................................................................59
3.2
Supported data types..................................................................................................................60
3.3
Configuring the Channel..............................................................................................................61
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
3
Table of contents
3.3.1
3.3.2
3.3.3
3.3.4
3.3.4.1
3.3.4.2
4
5
4
Configuring the "Mitsubishi Ethernet" channel............................................................................61
How to configure a "Mitsubishi FX3U Series" channel unit connection.......................................61
How to configure a "Mitsubishi Q Series" channel unit connection.............................................63
Configuring the tags....................................................................................................................64
Configuring the tags....................................................................................................................64
How to configure a tag.................................................................................................................66
Modbus TCPIP...........................................................................................................................................69
4.1
"Modbus TCP/IP" channel...........................................................................................................69
4.2
Supported Data Types.................................................................................................................70
4.3
4.3.1
4.3.2
4.3.3
4.3.3.1
4.3.3.2
4.3.3.3
4.3.3.4
Configuring the Channel..............................................................................................................71
Configuring the "Modbus TCPIP" Channel..................................................................................71
How to configure a connection....................................................................................................71
Configuring the tags....................................................................................................................73
Configuring the tags....................................................................................................................73
How to Configure a Tag with Bit by Bit Access...........................................................................75
How to Configure a Tag with Word by Word Access...................................................................76
How to Configure a Text Tag.......................................................................................................77
OPC Channel..............................................................................................................................................79
5.1
WinCC OPC Channel..................................................................................................................79
5.2
OPC Item Manager......................................................................................................................81
5.3
Overview of the Supported WinCC Data Types..........................................................................85
5.4
5.4.1
5.4.2
5.4.2.1
5.4.2.2
5.4.2.3
5.4.3
5.4.4
5.4.4.1
5.4.4.2
5.4.4.3
5.4.5
5.4.5.1
5.4.5.2
5.4.5.3
WinCC OPC DA Client................................................................................................................86
Functionality of the WinCC OPC DA Client.................................................................................86
How to Access a WinCC Tag with the OPC Item Manager.........................................................87
How to Access a WinCC Tag with the OPC Item Manager.........................................................87
Configuring the OPC Channel on the WinCC OPC DA Client.....................................................88
Configuring Access with the OPC Item Manager........................................................................88
Accessing a WinCC Tag without the OPC Item Manager...........................................................92
Using Structures on a WinCC OPC DA Client.............................................................................94
How to Use Structures on the WinCC OPC DA Client................................................................94
Configuring Structures and Structure Tags on the WinCC OPC DA Server...............................95
How to Configure Structures on the WinCC OPC DA Client.......................................................96
Error Handling in the Event of Disturbed OPC DA Communication............................................97
Error Handling in the Event of Disturbed OPC Communication..................................................97
WinCC as OPC DA Server..........................................................................................................98
WinCC as OPC DA Client.........................................................................................................100
5.5
5.5.1
5.5.2
5.5.2.1
5.5.2.2
5.5.3
WinCC OPC XML Client............................................................................................................102
Functionality of the WinCC OPC XML Client.............................................................................102
How to Access a WinCC Tag with the OPC Item Manager.......................................................103
How to Access a WinCC Tag with the OPC Item Manager.......................................................103
Configuring Access with the OPC Item Manager......................................................................103
Accessing a WinCC Tag without the OPC Item Manager.........................................................107
5.6
5.6.1
5.6.2
5.6.2.1
5.6.2.2
WinCC OPC UA client...............................................................................................................110
Functionality of the WinCC OPC UA client................................................................................110
Accessing a tag using the OPC Item Manager..........................................................................110
Accessing an OPC tag using the OPC Item Manager...............................................................110
How to set up a server certificate..............................................................................................111
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Table of contents
5.6.2.3
5.6.3
5.6.3.1
5.6.3.2
6
7
8
How to configure access to a tag using the OPC Item Manager...............................................113
Error handling in event of disturbed communication.................................................................117
WinCC as OPC UA server.........................................................................................................118
WinCC as OPC UA client..........................................................................................................120
PROFIBUS FMS.......................................................................................................................................123
6.1
WinCC channel "PROFIBUS FMS"...........................................................................................123
6.2
Data type of the tags.................................................................................................................124
6.3
6.3.1
6.3.1.1
6.3.1.2
6.3.1.3
6.3.2
6.3.2.1
6.3.2.2
6.3.2.3
Configuring the Channel............................................................................................................125
Configuring a connection ..........................................................................................................125
Configuring a connection...........................................................................................................125
Configuring the connection in configuration mode....................................................................126
How to configure the connection in Runtime.............................................................................128
Configuring the tags..................................................................................................................129
Configuring the tags..................................................................................................................129
Configuring the address of the tags in configuration mode.......................................................129
How to configure the address of the tags in runtime.................................................................130
S5 Ethernet Layer 4..................................................................................................................................133
7.1
WinCC Channel "SIMATIC S5 Ethernet Layer 4"......................................................................133
7.2
Data type of the tags.................................................................................................................134
7.3
7.3.1
7.3.2
7.3.3
7.3.3.1
7.3.3.2
7.3.3.3
7.3.3.4
7.3.3.5
7.3.3.6
7.3.4
7.3.4.1
7.3.4.2
7.3.4.3
Configuring the Channel............................................................................................................135
Configuring the channel "SIMATIC S5 Ethernet Layer 4".........................................................135
How to configure the connection...............................................................................................135
Configuring the tags..................................................................................................................137
Configuring the tags..................................................................................................................137
Addresses of tags......................................................................................................................137
How to Configure a Tag with Bit by Bit Access.........................................................................138
How to Configure a Tag with Byte by Byte Access...................................................................140
How to Configure a Tag with Word by Word Access.................................................................141
How to configure a raw data tag................................................................................................143
System parameters...................................................................................................................144
System parameters of the channel unit.....................................................................................144
How to Change the Device Name.............................................................................................145
How to change the transport parameter....................................................................................146
7.4
7.4.1
7.4.2
7.4.2.1
7.4.2.2
7.4.2.3
7.4.2.4
Appendix....................................................................................................................................148
Appendix....................................................................................................................................148
Internal error codes and constants............................................................................................148
Internal error codes and constants............................................................................................148
Error codes during connection disturbances.............................................................................148
iNA960 messages.....................................................................................................................151
SCI messages...........................................................................................................................152
S5 PROFIBUS FDL..................................................................................................................................155
8.1
WinCC channel "SIMATIC S5 Profibus FDL"............................................................................155
8.2
Supported data types and data ranges.....................................................................................157
8.3
Features of the WinCC channel "SIMATIC S5 Profibus FDL"...................................................158
8.4
Configuring the Channel............................................................................................................160
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
5
Table of contents
9
10
6
8.4.1
8.4.2
8.4.3
8.4.4
8.4.4.1
8.4.4.2
8.4.4.3
8.4.4.4
8.4.5
8.4.5.1
8.4.5.2
8.4.5.3
How to configure the channel "SIMATIC S5 Profibus FDL"......................................................160
Channel unit "FDL (CP5412/A2-1)"...........................................................................................160
How to configure a connection..................................................................................................162
Configuring the tags..................................................................................................................163
Configuring the tags..................................................................................................................163
How to Configure a Tag with Bit by Bit Access.........................................................................163
How to Configure a Tag with Byte by Byte Access...................................................................165
How to configure a tag with word by word access.....................................................................166
System parameters...................................................................................................................168
System parameters of the channel unit.....................................................................................168
How to Change the Device Name.............................................................................................169
How to change the write/read monitoring time of process values.............................................170
8.5
8.5.1
8.5.2
8.5.2.1
8.5.2.2
8.5.3
8.5.3.1
8.5.3.2
8.5.3.3
Special Functions......................................................................................................................171
Special functions of the "SIMATIC S5 Profibus FDL" Channel.................................................171
Raw data tags of the "SIMATIC S5 Profibus FDL" channel......................................................171
Raw data tags of the "SIMATIC S5 Profibus FDL" channel......................................................171
How to configure raw data tags.................................................................................................171
Configuring the communication types.......................................................................................173
Configuring the communication types.......................................................................................173
How to configure an active data transfer...................................................................................173
How to configure a passive data transfer..................................................................................175
8.6
8.6.1
8.6.2
8.6.3
Example of configuring the "SIMATIC S5 Profibus FDL" channel.............................................178
Example of configuring the "SIMATIC S5 Profibus FDL" channel.............................................178
How to configure the data handling blocks in the AS................................................................178
How to configure an I/O Field....................................................................................................181
S5 Programmers Port AS511...................................................................................................................185
9.1
WinCC channel "SIMATIC S5 Programmers Port AS511" .......................................................185
9.2
Data type of the tags.................................................................................................................186
9.3
9.3.1
9.3.2
9.3.3
9.3.3.1
9.3.3.2
9.3.3.3
9.3.3.4
Configuring the Channel............................................................................................................187
Configuring the "SIMATIC S5 Programmers Port AS511" channel...........................................187
How to configure the connection...............................................................................................187
Configuring the tags..................................................................................................................189
Configuring the tags..................................................................................................................189
How to configure the address of a tag.......................................................................................189
How to configure a tag with bit-wise access..............................................................................192
How to Configure a Tag with Byte by Byte Access...................................................................193
S5 Serial 3964R........................................................................................................................................195
10.1
WinCC channel "SIMATIC S5 Serial 3964R" ...........................................................................195
10.2
Data type of the tags.................................................................................................................196
10.3
10.3.1
10.3.2
10.3.3
10.3.3.1
10.3.3.2
10.3.3.3
10.3.3.4
Configuring the Channel............................................................................................................197
Configuring the "SIMATIC S5 Serial 3964R" channel...............................................................197
How to configure the connection...............................................................................................197
Configuring the tags..................................................................................................................199
Configuring the tags..................................................................................................................199
How to configure the address of the tag....................................................................................199
How to configure a tag with bit-wise access..............................................................................201
How to Configure a Tag with Byte by Byte Access...................................................................202
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Table of contents
11
SIMATIC S7 Protocol Suite......................................................................................................................205
11.1
"SIMATIC S7 Protocol Suite" Channel......................................................................................205
11.2
WinCC Channel "SIMATIC S7 Protocol Suite"..........................................................................206
11.3
Channel unit selection...............................................................................................................207
11.4
Overview of the supported data types.......................................................................................211
11.5
11.5.1
11.5.2
11.5.3
11.5.3.1
11.5.3.2
11.5.3.3
11.5.3.4
11.5.3.5
11.5.3.6
11.5.3.7
11.5.3.8
11.5.4
11.5.4.1
11.5.4.2
11.5.4.3
11.5.4.4
11.5.4.5
11.5.5
11.5.5.1
11.5.5.2
11.5.5.3
11.5.5.4
Configuring the Channel............................................................................................................212
"SIMATIC S7 Protocol Suite" Channel - Configuration..............................................................212
How to configure the "SIMATIC S7 Protocol Suite" channel.....................................................212
Channel units.............................................................................................................................213
Channel units of the "SIMATIC S7 Protocol Suite" channel......................................................213
"Industrial Ethernet (I+II)" channel units"...................................................................................214
"MPI" channel unit.....................................................................................................................217
"Named Connections" channel unit...........................................................................................219
"PROFIBUS (I+II)" channel units...............................................................................................222
"Slot PLC" channel unit.............................................................................................................224
"Soft PLC" channel unit.............................................................................................................226
"TCP/IP" channel unit................................................................................................................227
Configuring the tags..................................................................................................................230
Configuring the tags..................................................................................................................230
How to Configure a Tag with Bit by Bit Access.........................................................................230
How to Configure a Tag with Byte by Byte Access...................................................................232
How to Configure a Tag with Word by Word Access.................................................................233
How to Configure a Text Tag.....................................................................................................234
System parameters...................................................................................................................236
System Parameters of the Channel Unit...................................................................................236
Cyclic read services in PLC.......................................................................................................237
How to Configure the System Parameters................................................................................238
How to Change the Logical Device Name.................................................................................240
11.6
11.6.1
11.6.2
11.6.2.1
11.6.2.2
11.6.2.3
11.6.2.4
11.6.2.5
11.6.2.6
11.6.2.7
11.6.2.8
Special functions.......................................................................................................................242
Special functions of the "SIMATIC S7 Protocol Suite" Channel................................................242
Data exchange with the S7 function block AR_SEND...............................................................242
Data exchange with the S7 function block AR_SEND...............................................................242
Data Block - Structure and Parameters.....................................................................................243
Overview of the properties of the AR_SEND variants...............................................................248
AR_SEND variant for an archive tag.........................................................................................250
Example 1 for data block structure: An archive tag; each process value has a time stamp.....252
Example 2 for data block structure: One archive tag; equally spaced time stamp....................252
Example 3 for data block structure: An archive tag; each process value has its own time stamp253
Example 4 for data block structure: An archive tag; each process value with relative time stamp
(time difference).........................................................................................................................254
11.6.2.9 AR_SEND variant for multiple archive tags...............................................................................255
11.6.2.10 Example 5 for data block structure: Multiple archive tags; each process value has its own time
stamp....................................................................................................................................259
11.6.2.11 Example 6 for data block structure: Multiple archive tags; equally spaced time stamp.......261
11.6.2.12 Example 7 for data block structure: Multiple archive tags; each process value has its own time
stamp....................................................................................................................................263
11.6.2.13 Example 8 for data block structure: Multiple archive tags; process values with relative time
stamp (time difference).........................................................................................................265
11.6.2.14 AR_SEND variant for multiple archive tags (optimized).......................................................267
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
7
Table of contents
11.6.2.15 Example 9 for data block structure: multiple archive tags;optimized....................................268
11.6.2.16 How to configure the AR _SEND variant for an archive tag.................................................269
11.6.2.17 How to configure the AR _SEND variant for multiple archive tags.......................................272
11.6.3 Raw data tags of the Channel "SIMATIC S7 Protocol Suite"....................................................275
11.6.3.1 Raw data tags of the Channel "SIMATIC S7 Protocol Suite"....................................................275
11.6.3.2 Raw data tag as byte array........................................................................................................276
11.6.3.3 How to Configure a Raw Data Tag as Byte Array.....................................................................277
11.6.3.4 Raw data tag for BSEND/BRCV functions of S7 communication..............................................279
11.6.3.5 How to Configure a Raw Data Tag for ""BSEND/BRCV" functions...........................................282
11.6.4 Software Redundancy...............................................................................................................283
11.6.4.1 Software Redundancy...............................................................................................................283
11.6.4.2 Software Redundancy - Connection-specific internal tags........................................................285
11.6.4.3 How To Configure a Software Redundancy..............................................................................289
11.6.4.4 How to Clear a Software Redundancy in WinCC......................................................................292
11.6.4.5 How to Check the WinCC Startup Parameters..........................................................................292
11.6.4.6 How To Load WinCC's system messages into Alarm Logging.................................................293
11.6.4.7 Error codes during connection disturbances.............................................................................293
12
13
14
8
SIMATIC S7-1200, S7-1500 Channel.......................................................................................................295
12.1
"SIMATIC S7-1200, S7-1500 Channel" channel.......................................................................295
12.2
Overview of the supported data types.......................................................................................296
12.3
12.3.1
12.3.2
12.3.3
12.3.3.1
12.3.3.2
12.3.3.3
12.3.3.4
12.3.3.5
Configuring the channel.............................................................................................................297
Configuration of the "SIMATIC S7-1200, S7-1500 Channel" channel.......................................297
How to configure a connection..................................................................................................297
Configuring the tags..................................................................................................................299
Configuring the tags..................................................................................................................299
How to Configure a Tag with Bit by Bit Access.........................................................................300
How to Configure a Tag with Byte by Byte Access...................................................................301
How to Configure a Tag with Word by Word Access.................................................................302
How to Configure a Text Tag.....................................................................................................303
SIMATIC TI Ethernet Layer 4...................................................................................................................305
13.1
WinCC channel "SIMATIC TI Ethernet Layer 4"........................................................................305
13.2
Data type of the tags.................................................................................................................306
13.3
13.3.1
13.3.2
13.3.3
13.3.3.1
13.3.3.2
13.3.3.3
13.3.3.4
13.3.4
13.3.4.1
13.3.4.2
13.3.4.3
Configuring the Channel............................................................................................................307
Configuring the channel "SIMATIC TI Ethernet Layer 4"...........................................................307
How to configure the connection...............................................................................................307
Configuring the tags..................................................................................................................309
Configuring the tags..................................................................................................................309
How to configure the address of a tag.......................................................................................309
How to configure a tag with bit-wise access..............................................................................310
How to Configure a Tag with Byte by Byte Access...................................................................311
System parameters...................................................................................................................313
System parameters of the channel unit.....................................................................................313
How to Change the Device Name.............................................................................................313
How to change the transport parameter....................................................................................315
SIMATIC TI Serial.....................................................................................................................................317
14.1
WinCC channel "SIMATIC TI Serial" ........................................................................................317
14.2
Data type of the tags.................................................................................................................318
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Table of contents
14.3
14.3.1
14.3.2
14.3.3
14.3.3.1
14.3.3.2
14.3.3.3
14.3.3.4
15
16
Configuring the Channel............................................................................................................319
Configuring the "SIMATIC TI Serial" channel............................................................................319
How to configure the connection...............................................................................................319
Configuring the tags..................................................................................................................321
Configuring the tags..................................................................................................................321
How to configure the address of a tag.......................................................................................321
How to configure a tag with bit-wise access..............................................................................322
How to Configure a Tag with Byte by Byte Access...................................................................323
SIMOTION................................................................................................................................................325
15.1
WinCC channel "SIMOTION"....................................................................................................325
15.2
Overview of the supported data types.......................................................................................326
15.3
15.3.1
15.3.2
15.3.3
15.3.4
15.3.5
15.3.6
15.3.7
15.3.7.1
15.3.7.2
15.3.7.3
Configuring the channel.............................................................................................................327
Configuration of the "SIMOTION" channel................................................................................327
How to export a SIMOTION SCOUT project ............................................................................327
How to create a WinCC project with Simotion Mapper..............................................................328
How to change a WinCC project with Simotion Mapper............................................................329
How to change the connection parameters...............................................................................331
How to change the tag address.................................................................................................332
System parameter configuration................................................................................................333
System Parameters of the Channel Unit...................................................................................333
How to Configure the System Parameters................................................................................333
How to Change the Logical Device Name.................................................................................335
15.4
15.4.1
15.4.2
Diagnosis "SIMOTION" channel................................................................................................337
Diagnosis possibilities of the "SIMOTION" channel..................................................................337
Description of Log File Entries...................................................................................................337
System Info...............................................................................................................................................341
16.1
"System Info" Channel...............................................................................................................341
16.2
WinCC System Info Channel.....................................................................................................342
16.3
Overview of the Supported System Information........................................................................344
16.4
Differences to Other Software Components..............................................................................349
16.5
16.5.1
Configuring the Channel............................................................................................................350
How to Configure the System Info Channel..............................................................................350
16.6
16.6.1
16.6.2
16.6.3
16.6.4
16.6.5
16.6.6
16.6.7
16.6.8
16.6.9
16.6.10
16.6.11
16.6.12
Examples of Evaluating and Displaying System Information....................................................351
How To Call Up and Evaluate System Information...................................................................351
How to Configure a Tag in the System Info Channel................................................................351
How to Display the Time in an I/O Field....................................................................................352
How to Display the Free Disk Capacity in a Bar Graph.............................................................354
How to Display the CPU Load in a Trend Window....................................................................355
How to Configure a Message Regarding Free Disk Capacity...................................................356
How to Display a Message regarding the Available Disk Capacity...........................................358
How to Display the Printer Status in a Status Display...............................................................359
How to Check the WinCC Startup Parameters..........................................................................361
How to Insert a Bar Graph.........................................................................................................361
How to Insert an I/O Field..........................................................................................................362
How to Start Runtime................................................................................................................362
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
9
Table of contents
16.7
16.7.1
16.7.1.1
16.7.2
16.7.2.1
16.7.2.2
16.7.2.3
16.7.2.4
16.7.2.5
16.7.2.6
17
10
Special Functions......................................................................................................................363
Use in Multi-User and Client Systems.......................................................................................363
Use in Multi-User and Client Systems.......................................................................................363
Example of monitoring system information from multiple servers.............................................363
Monitoring the system information of several servers on a WinCC client.................................363
How to Configure the First Server.............................................................................................364
How to Configure the Second Server........................................................................................365
How to Import the Tags to the WinCC Client.............................................................................366
How to Configure the Process Picture on the WinCC Client.....................................................367
How to Activate the Project.......................................................................................................368
Communication - Diagnostics...................................................................................................................369
17.1
Diagnosis of Channels and Tags...............................................................................................369
17.2
General Information about Error Detection................................................................................370
17.3
17.3.1
17.3.2
17.3.3
17.3.4
17.3.4.1
17.3.4.2
17.3.4.3
17.3.4.4
17.3.4.5
17.3.4.6
17.3.4.7
Channel Diagnosis ...................................................................................................................371
Channel diagnosis.....................................................................................................................371
"Status - Logical Connections" Function...................................................................................371
How to Use the "Status - Logical Connections" Function to Check a Channel.........................371
Diagnosis of Channels with Channel Diagnosis........................................................................373
Principle of Channel Diagnosis..................................................................................................373
Channel Diagnosis with ActiveX Control...................................................................................374
How to Check a Channel with Channel Diagnosis as an ActiveX Control................................374
Diagnosing a Channel with "Channel Diagnosis"......................................................................375
How to Check a Channel with Channel Diagnosis....................................................................376
How to Configure the Trace Function of a Channel..................................................................377
How to Start Runtime................................................................................................................378
17.4
17.4.1
17.4.2
17.4.3
17.4.3.1
17.4.3.2
17.4.3.3
Diagnosis of "System Info" Channel..........................................................................................379
"System Info" Channel - Diagnostic Options.............................................................................379
Description of Log File Entries...................................................................................................379
Determining the Cause of Incorrect Tag Values........................................................................380
How to Determine the Cause of Incorrect Tags........................................................................380
How to Check the Channel and the Connection........................................................................380
How to Check a Tag..................................................................................................................382
17.5
17.5.1
17.5.2
17.5.3
17.5.3.1
17.5.3.2
17.5.3.3
17.5.3.4
17.5.3.5
17.5.3.6
Diagnosis of the "SIMATIC S7 Protocol Suite" Channel...........................................................384
"SIMATIC S7 Protocol Suite" Channel - Diagnostic Options.....................................................384
Description of Log File Entries...................................................................................................384
Determining the Cause of Incorrect Tag Values........................................................................387
How to Determine the Cause of Incorrect Tags........................................................................387
How to Check the Configuration of the Communication Processor...........................................387
Checking the Communication Processor under SIMATIC NET................................................389
How to Check the Configuration of the Connection and Tags..................................................390
How to Check the Channel and the Connection........................................................................391
How to Check a Tag..................................................................................................................393
17.6
17.6.1
17.6.2
17.6.3
17.6.3.1
17.6.3.2
Diagnosis of the "SIMATIC S5 Profibus FDL" Channel.............................................................395
Diagnostic Options for the "SIMATIC S5 PROFIBUS FDL" Channel........................................395
Description of Log File Entries...................................................................................................395
Determining the Cause of Incorrect Tag Values........................................................................396
How to Determine the Cause of Incorrect Tags........................................................................396
How to Check the Configuration of the Communication Processor...........................................397
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Table of contents
17.6.3.3
17.6.3.4
17.6.3.5
17.6.3.6
Checking the Communication Processor under SIMATIC NET................................................398
How to Check the Configuration of the Connection and Tags..................................................399
How to Check the Channel and the Connection........................................................................401
How to Check a Tag..................................................................................................................403
17.7
17.7.1
17.7.2
17.7.2.1
17.7.2.2
17.7.2.3
17.7.3
17.7.3.1
17.7.3.2
17.7.3.3
17.7.3.4
Diagnosis of the "OPC" Channel...............................................................................................404
Possibilities for Diagnosing the "OPC" Channel........................................................................404
Description of Log File Entries...................................................................................................404
Description of Log File Entries...................................................................................................404
Entries for "INFO" Flag..............................................................................................................405
Entries for "ERROR" Flag..........................................................................................................406
Determining the Cause of Incorrect Tag Values........................................................................407
How to Determine the Cause of Invalid Tags............................................................................407
How to Check the Configuration Data.......................................................................................408
How to Check the Channel and the Connection........................................................................409
How to Check a Tag..................................................................................................................411
17.8
17.8.1
17.8.2
17.8.3
17.8.4
17.8.5
17.8.6
Quality of Tags..........................................................................................................................412
Quality of Tags..........................................................................................................................412
Quality Codes of Tags...............................................................................................................414
Tag Status.................................................................................................................................418
Using the Tag Status to Monitor Connection Status..................................................................420
Monitoring Tag Status Using Global Actions.............................................................................421
How to Check an Internal Tag...................................................................................................422
Index.........................................................................................................................................................425
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
11
Process communication
1.1
1
Communication Basics
Introduction
Communication is defined as the exchange of data between two communication partners.
Communication
Communication partners can be any component of a network that is in a position to
communication with others and to exchange data. In the WinCC, these can be central and
communication modules in the automation system (AS) as well as communication processors
in the PC.
The transferred data between communication partners can serve many different purposes. In
the case of WinCC, these may be:
● Controlling a process
● Calling data from a process
● Indicating unexpected states in the process
● Process data archiving
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
13
Process communication
1.2 Basic Rules for Configuring Connections
1.2
Basic Rules for Configuring Connections
Acquisition cycle and update time
The acquisition cycles for the tags defined in the configuration software are major factors for
the achievable update times.
The update time is the sum of the acquisition cycle, the transmission time and the processing
time.
To achieve optimum update times, remember the following points during configuration:
● Optimize the maximum and minimum size of the data areas.
● Define data areas that belong together as belonging together. If you set up one large area
instead of multiple small areas, it improves the update time.
● Acquisition cycles that are too small decrease performance. Set the acquisition cycle
according to the rate of change of the process values. Take the temperature of an oven for
example, it changes much more slowly than the speed of an electrical drive.
● Put the tags of an alarm or a screen in one data area without gaps.
● Changes in the controller can only be detected reliably if these are available for at least
one acquisition cycle.
● Set the transmission rate to the highest possible value for error-free transmission.
Images
The refresh rate of screens is determined by the type and volume of data to be visualized.
In the interest of short update times, ensure that you only configure short acquisition times for
objects that require fast updates.
Curves
When using bit-triggered curves, if the group bit is set in the "Curve transfer area", all curves
for which the bit is set in this area are updated on the WinCC station. It resets the bits in the
next cycle.
Only after all bits have been reset in the WinCC station may the group bit be set again in the
PLC program.
14
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
1.3
WinCC process communication
1.3.1
WinCC process communication
Introduction
You can access process tags (external tags) in an automation system from WinCC. Before
you configure the process link in WinCC however, you should use a checklist to check whether
the following prerequisites have been met:
● The automation system must be equipped with a communication interface supported by a
communication driver in WinCC.
● This interface must be configured in the automation system so that the controller program
can access the interface with the communication calls. The configuration parameters for
the communication hardware must be known.
● The addresses of the tags that WinCC should access must be known. Note that the
addresses depend on the automation system.
● The respective communication hardware (communication processor, standard I/O port
COMx, ...) must be installed in the WinCC system. In order to install this hardware, the
supplied operating system driver (hardware driver) must also have been installed
previously. The settings for the hardware and software of the communication processor
must be known.
● Depending on the communication processor used in the WinCC system, more settings may
have to be made. When using industrial Ethernet or PROFIBUS for example, a local
database must be created. This connection parameter also has to be known.
For operation in runtime, a physical connection must also exist between WinCC and the AS,
so that you can access the external tags.
1.3.2
Principle of WinCC communication
Introduction
WinCC manages its tags centrally using so-called tag management. All of data and tags
created in the project and stored in the project database are captured and management in
runtime by WinCC.
All applications, such as e.g. Graphics Runtime, Alarm Logging Runtime or Tag Logging
Runtime (Global Script), must request the data in the for of WinCC tags from tag management.
Communication between WinCC and Automation systems (AS)
Communication in the industrial communication with WinCC means that information is
exchanged with tags and process values. To capture the process values, the WinCC
communication driver sends request telegrams to the AS. This in turn sends the requested
process values back to WinCC in corresponding response telegrams.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
15
Process communication
1.3 WinCC process communication
A physical connection must then exist between WinCC and the AS. The properties of this
connection, such as e.g. transfer medium and communication network, define the conditions
for communication and are required for configuring the communication in WinCC.
Communication driver
A communication driver is a software component that establishes a connection between an
AS and the tag management of WinCC, which enables the supply of WinCC tags with process
values. In WinCC, there is a number of communication drivers for connecting various AS with
different bus systems.
Every communication driver can only be bound into a WinCC project one time.
16
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Communication drivers under WinCC are also called "Channels" and have the file extension
"*.chn". All of the communication drivers installed on the computer are located in subdirectory
"\bin" in the WinCC installation directory.
A communication driver has different channel units for different communication networks.
Channel Unit
Every channel unit serves as an interface with exactly one underlying hardware driver and
therefore to exactly one communication processor in the PC. Every channel unit used must
therefore be allocated with the respective communication processor.
For some channel units, an additional configuration is performed in the so-called system
parameters. For channel units that work on the transport layer (Layer 4) of the OSI model, the
transport parameters are also defined.
Connection (logical)
If WinCC and the AS are correctly connected, physically, then a communication driver and a
corresponding channel unit are required in WinCC in order to create or configure a (logical)
connection with the AS. The data exchange will take place via this connection in Runtime.
In WinCC, there is a connection of a configured, logical allocation of two communication
partners for executing a certain communication service. Every connection has two end points
that also contain necessary information for addressing the communication partner and other
attributes for establishing the connection.
A connection is configured under a channel unit with your specific connection parameters. A
number of connections can also be created under one channel unit, depending on the
communication driver.
1.3.3
External tags
1.3.3.1
External tags
Introduction
In order to obtain certain data of an AS, WinCC tags are required. These tags that affect the
connection to an AS are designated as external tags. Other tags that have no process
connection are designated as internal tags.
Data Type and Type Conversion
In configuring external tags, besides tag names you must define a data type and with some
data types a type conversion is required:
The data type determines the data format in WinCC. Along with the type conversion, the
conversion from AS format to the WinCC format is defined. The type conversion applies for
both transfer directions:
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
17
Process communication
1.3 WinCC process communication
● In the AS: e.g. for certain functions (such as timer values / BCD displays) or with the
information to be addressed (e.g. byte, word addresses in data block or I/O area).
● In WinCC: e.g. for analog value processing or calculations.
In practice, normally the AS data format is normally defined. The following possibilities are
available for selecting the WinCC format:
● The WinCC data format can match the AS format. This is done by selecting a type
conversion that uses the same formats on both sides and considers the leading sign
independent of the WinCC data type, e.g. "WordToSignedWord". If this cannot be achieved
with the selected data type, it must be changed in WinCC.
● The WinCC format is set up in accordance of the value processing in WinCC.
When selecting the data type and the type conversion, if required, the following points are
important:
● Leading sign: Should it be considered for the adaptation? Can negative tag values also
occur during operation? (such as e.g. with control differences as percentage)
● Value Range: Are tag values that occur during operation in the value range of both formats
or can a possible overflow of the value be expected in WinCC or the AS ? If an overflow
occurs, a value cannot be displayed on the other side or it can lead to faults in subsequent
processing.
● Different type conversions with the same value range: It is possible that different type
conversions of a data type have the same value range. E.g. "ByteToUnsignedDword" and
"ByteToUnsignedWord" with value range [0...127]. In this case, check which format is
defined for the data from the AS and whether this format wastes resources unnecessarily
because of over-dimensioning. (E.g. DWord instead of Word).
If the value range required in the AS is not covered by the selected type conversion, you must
change the data type in WinCC.
Note
Communication to the automation system can be disrupted when a process tag is configured
incorrectly, for example, due to an address error.
WinCC data types and type conversion
The following table shows which WinCC data types support a type conversion.
18
Data type
Type conversion
Binary tag
No
Unsigned 8-bit value
Yes
Signed 8-bit value
Yes
Unsigned 16-bit value
Yes
Signed 16-bit value
Yes
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Data type
Type conversion
Unsigned 32-bit value
Yes
Signed 32-bit value
Yes
Floating-point number 32-bit IEEE 754
Yes
Floating-point number 64-bit IEEE 754
Yes
Text tag 8-bit character set
No
Text tag 16-bit character set
No
Raw data type
No
Note
Not that with a type conversion, the data sent by AS can be interpreted by WinCC within the
selected format adaptation. If the data cannot be interpreted by WinCC, a fault entry occurs
in the file "WinCC_sys_0x.log" in directory "..\Siemens\WinCC\Diagnose".
Linear scaling of numerical tag types
A linear scaling can be performed for numerical data types. The value range for a variable
existing in the process can be represented linearly within a certain value range of a WinCC
tag.
The process can e.g. request the definition of a set value in the unit [bar] but this value should
be defined by the user in [mbar] in WinCC. With linear scaling, the value range in the process
[0...1] can be converted to value range [0...1000] of the WinCC tags.
Length definition for text tags
A length definition is required for tags of data types "Text tag 8-bit character set" and "Text tag
16-bit character set". A text tag that is required to accommodate 10 characters later must be
ten long for the "8-bit character set" and 20 long for the "16-bit character set".
Addressing in the automation system
WinCC tags are assigned to a data range in the AS. These must be addressed in the AS in a
certain way. The addressing type depends on the type of communication partner.
1.3.3.2
How to Create a New Connection
Introduction
External tags can only be created on the basis of a connection to an AS. If the required
connection does not exist, it must be created first.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
19
Process communication
1.3 WinCC process communication
Requirements
● The required communication processor and the respective hardware driver are installed.
● The desired communication driver is also installed, e.g. "SIMATIC S7 Protocol Suite".
Procedure
1. Expand the view of the communication drivers in "Tag management".
2. Select the desired channel unit, e.g. "PROFIBUS".
3. Select the entry "New Connection..." in the pop-up menu of the channel unit.
4. Give the connection a unique name within the project in the field "Name" on the General
tab.
5. Click the "Properties" button to open the "Connection Parameters" dialog. Define the
required parameter for this connection. More information can be found under Help /
Documentation for the respective channel.
6. Close all dialogs using the "OK" button.
1.3.3.3
An external tag is configured as follows
Introduction
The procedures for creating a tag is similar for almost all data types.
20
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
For some data types however, special settings are required (steps 5 - 7).
Requirements
● The required communication processor and the hardware driver are installed.
● The desired communication driver is installed, e.g. "SIMATIC S7 Protocol Suite".
● A connection is already created based on a channel unit (e.g. "PROFIBUS").
Procedure
1. Choose the "New Tag..." option from the shortcut menu for the desired connection. The
"Tag Properties" dialog opens.
2. Define a variable name that is unique in the WinCC project, e.g. WinCCTag_01", in field
"Name" on the General tab.
3. Define the data type for the tag in the "Data type" field, e.g. "Floating Point Number 64 bit
IEEE 754".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
21
Process communication
1.3 WinCC process communication
4. Click on the "Select" button to open dialog "Tag properties" for defining the address range
of the tags in the AS.
With channels that do not support bit-/byte-access with binary or 8 bit tags, first the dialog
"Bit-/Byte-Tag" and then dialog "Tag properties" will also be shown.
More information is located under "Principle of the BinWrite-Mechanism".
Close the dialog "Bit-/Byte-Variable" or "Tag properties" with the "OK" button.
5. With numerical tags, WinCC suggests a format adaptation in the "Format adaptation" field.
Select another format adaptation if necessary. The display is in sequence "X to Y", whereby
X = WinCC format and Y = AS format, e.g. "DoubleToDouble".
6. Activate the checkbox "Linear scaling" to scale a numerical tag linearly. Enter the upper
and lower limits for the "Process value range" (in AS) and "Tag value range" (in WinCC).
7. The "Length" field is activated for a text tag. Enter the length of the text tag in characters
here.
8. Close all dialogs using the "OK" button.
1.3.3.4
Format adaptation sorted by WinCC data type
Introduction
When configuring external tags, another format adaptation must be done for all numeric data
types.
The data type determines the data format on the WinCC side. The format adaptation also
defines the conversion from WinCC format to the AS format. The definition applies for both
transfer directions.
Choose the required WinCC data type in the following selection box. You are then provided
with a list of the respective possible format adaptations and value ranges in the table below.
WinCC Data Type
Table 1-1
Signed 8-bit value
Format adaptation "Signed 8-bit value"
Value range
CharToUnsignedByte
0...127
CharToUnsignedWord
0...127
CharToUnsignedDword
0...127
CharToSignedByte
-128...+127 (no conversion)
CharToSignedWord
-128...+127
CharToSignedDword
-128...+127
CharToMSBByte
-128...+127
CharToMSBWord
-128...+127
CharToMSBDword
-128...+127
CharToBCDByte
0...99
CharToBCDWord
0...127
CharToBCDDword
0...127
22
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Format adaptation "Signed 8-bit value"
Value range
CharToSignedBCDByte
-9...+9
CharToSignedBCDWord
-128...+127
CharToSignedBCDDword
-128...+127
CharToExtSignedBCDByte
-79...+79
CharToExtSignedBCDWord
-128...+127
CharToExtSignedBCDDword
-128...+127
CharToAikenByte
0...99
CharToAikenWord
0...127
CharToAikenDword
0...127
CharToSignedAikenByte
-9...+9
CharToSignedAikenWord
-128...+127
CharToSignedAikenDword
-128...+127
CharToExcessByte
0...99
CharToExcessWord
0...127
CharToExcessDword
0...127
CharToSignedExcessByte
-9...+9
CharToSignedExcessWord
-128...+127
CharToSignedExcessDword
-128...+127
Table 1-2
Unsigned 8-bit value
Format adaptation "Unsigned 8-bit value"
Value range
ByteToUnsignedByte
0...255 (no conversion)
ByteToUnsignedWord
0...255
ByteToUnsignedDword
0...255
ByteToSignedByte
0...127
ByteToSignedWord
0...255
ByteToSignedDword
0...255
ByteToBCDByte
0...99
ByteToBCDWord
0...255
ByteToBCDDword
0...255
ByteToAikenByte
0...99
ByteToAikenWord
0...255
ByteToAikenDword
0...255
ByteToExcessByte
0...99
ByteToExcessWord
0...255
ByteToExcessDword
0...255
Table 1-3
Signed 16-bit value
Format adaptation "Signed 16-bit value"
Value range
ShortToUnsignedByte
0...255
ShortToUnsignedWord
0...32767
ShortToUnsignedDword
0...32767
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
23
Process communication
1.3 WinCC process communication
Format adaptation "Signed 16-bit value"
Value range
ShortToSignedByte
-128...+127
ShortToSignedWord
-32768...+32767 (no conversion)
ShortToSignedDword
-32768...+32767
ShortToMSBByte
-127...+127
ShortToMSBWord
-32767...+32767
ShortToMSBDword
-32768...+32767
ShortToBCDByte
0...99
ShortToBCDWord
0...9999
ShortToBCDDword
0...32767
ShortToSignedBCDByte
-9...+9
ShortToSignedBCDWord
-999...+999
ShortToSignedBCDDword
-32768...+32767
ShortToExtSignedBCDByte
-79...+79
ShortToExtSignedBCDWord
-7999...+7999
ShortToExtSignedBCDDword
-32768...+32767
ShortToAikenByte
0...99
ShortToAikenWord
0...9999
ShortToAikenDword
0...32767
ShortToSignedAikenByte
-9...+9
ShortToSignedAikenWord
-999...+999
ShortToSignedAikenDword
-32768...+32767
ShortToExcessByte
0...99
ShortToExcessWord
0...9999
ShortToExcessDword
0...32767
ShortToSignedExcessByte
-9...+9
ShortToSignedExcessWord
-999...+999
ShortToSignedExcessDword
-32768...+32767
Table 1-4
Unsigned 16-bit value
Format adaptation "Unsigned 16-bit value"
Value range
WordToUnsignedWord
0...65535 (no conversion)
WordToUnsignedByte
0...255
WordToUnsignedDword
0...65535
WordToSignedByte
0...127
WordToSignedWord
0...32767
WordToSignedDword
0...65535
WordToBCDByte
0...99
WordToBCDWord
0...9999
WordToBCDDword
0...65535
WordToAikenByte
0...99
WordToAikenWord
0...9999
WordToAikenDword
0...65535
24
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Format adaptation "Unsigned 16-bit value"
Value range
WordToExcessByte
0...99
WordToExcessWord
0...9999
WordToExcessDword
0...65535
WordToSimaticCounter
0...999
WordToSimaticBCDCounter
0...999
Table 1-5
Signed 32-bit value
Format adaptation "Signed 32-bit value"
Value range
LongToSignedDword
-2147483647...+2147483647 (no conversion)
LongToUnsignedByte
0...255
LongToUnsignedWord
0...65535
LongToUnsignedDword
0...2147483647
LongToSignedByte
-128...+127
LongToSignedWord
-32768...+32767
LongToMSBByte
-127...+127
LongToMSBWord
-32767...+32767
LongToMSBDword
-2147483647...+2147483647
LongToBCDByte
0...99
LongToBCDWord
0...9999
LongToBCDDword
0...99999999
LongToSignedBCDByte
-9...+9
LongToSignedBCDWord
-999...+999
LongToSignedBCDDword
-9999999...+9999999
LongToExtSignedBCDByte
-79..+79
LongToExtSignedBCDWord
-7999...+7999
LongToExtSignedBCDDword
-79999999...+79999999
LongToAikenByte
0...99
LongToAikenWord
0...9999
LongToAikenDword
0...99999999
LongToSignedAikenByte
-9...+9
LongToSignedAikenWord
-999...+999
LongToSignedAikenDword
-9999999...+9999999
LongToExcessByte
0...99
LongToExcessWord
0...9999
LongToExcessDword
0...99999999
LongToSignedExcessByte
-9...+9
LongToSignedExcessWord
-999...+999
LongToSignedExcessDword
-9999999...+9999999
LongToSimaticTimer
10...9990000
LongToSimaticBCDTimer
10...9990000
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
25
Process communication
1.3 WinCC process communication
Table 1-6
Unsigned 32-bit value
Format adaptation "Unsigned 32-bit value"
Value range
DwordToUnsignedDword
0...4294967295 (no conversion)
DwordToUnsignedByte
0...255
DwordToUnsignedWord
0...65535
DwordToSignedByte
0...127
DwordToSignedWord
0...32767
DwordToSignedDword
0...2147483647
DwordToBCDByte
0...99
DwordToBCDWord
0...9999
DwordToBCDDword
0...99999999
DwordToAikenByte
0...99
DwordToAikenWord
0...9999
DwordToAikenDword
0...99999999
DwordToExcessByte
0...99
DwordToExcessWord
0...9999
DwordToExcessDword
0...99999999
DwordToSimaticTimer
10...9990000
DwordToSimaticBCDTimer
10...9990000
Table 1-7
Floating-point number 32-bit IEEE 754
Format adaptation "Floating-point number 32-bit IEEE 754"
Value range
FloatToFloat
+-3.402823e+38 (no conversion)
FloatToUnsignedByte
0...255
FloatToUnsignedWord
0...65535
FloatToUnsignedDword
0 to 4.294967e+09
FloatToSignedByte
-128...+127
FloatToSignedWord
-32768...+32767
FloatToSignedDword
-2.147483e+09 to +2.147483e+09
FloatToDouble
+-3.402823e+38
FloatToMSBByte
-127...+127
FloatToMSBWord
-32767...+32767
FloatToMSBDword
-2.147483e+09 to +2.147483e+09
FloatToBCDByte
0...99
FloatToBCDWord
0...9999
FloatToBCDDword
0 to 9.999999e+07
FloatToSignedBCDByte
-9...+9
FloatToSignedBCDWord
-999...+999
FloatToSignedBCDDword
-9999999...+9999999
FloatToExtSignedBCDByte
-79...+79
FloatToExtSignedBCDWord
-7999...+7999
FloatToExtSignedBCDDword
-7.999999e+07 to +7.999999e+07
FloatToAikenByte
0...99
26
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Format adaptation "Floating-point number 32-bit IEEE 754"
Value range
FloatToAikenWord
0...9999
FloatToAikenDword
0 to 9.999999e+07
FloatToSignedAikenByte
-9...+9
FloatToSignedAikenWord
-999...+999
FloatToSignedAikenDword
-9999999...+9999999
FloatToExcessByte
0...99
FloatToExcessWord
0...9999
FloatToExcessDword
0 to 9.999999e+07
FloatToSignedExcessByte
-9...+9
FloatToSignedExcessWord
-999...+999
FloatToSignedExcessDword
-9999999...+9999999
FloatToS5Timer
10...9990000
FloatToS5Float
+-1.701411e+38
Table 1-8
Floating-point number 64-bit IEEE 754
Format adaptation "Floating-point number 64-bit IEEE 754"
Value range
DoubleToDouble
+-1.79769313486231e+308 (no conversion)
DoubleToUnsignedByte
0...255
DoubleToUnsignedWord
0...65535
DoubleToUnsignedDword
0...4294967295
DoubleToSignedByte
-128...+127
DoubleToSignedWord
-32768...+32767
DoubleToSignedDword
-2147483647...+2147483647
DoubleToFloat
+-3.402823e+38
DoubleToMSBByte
-127...+127
DoubleToMSBWord
-32767...+32767
DoubleToMSBDword
-2147483647...+2147483647
DoubleToBCDByte
0...99
DoubleToBCDWord
0...9999
DoubleToBCDDword
0...99999999
DoubleToSignedBCDByte
-9...+9
DoubleToSignedBCDWord
-999...+999
DoubleToSignedBCDDword
-9999999...+9999999
DoubleToExtSignedBCDByte
-79...+79
DoubleToExtSignedBCDWord
-7999...+7999
DoubleToExtSignedBCDDword
-79999999...+79999999
DoubleToAikenByte
0...99
DoubleToAikenWord
0...9999
DoubleToAikenDword
0...99999999
DoubleToSignedAikenByte
-9...+9
DoubleToSignedAikenWord
-999...+999
DoubleToSignedAikenDword
-9999999...+9999999
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
27
Process communication
1.3 WinCC process communication
Format adaptation "Floating-point number 64-bit IEEE 754"
Value range
DoubleToExcessByte
0...99
DoubleToExcessWord
0...9999
DoubleToExcessDword
0...99999999
DoubleToSignedExcessByte
-9...+9
DoubleToSignedExcessWord
-999...+999
DoubleToSignedExcessDword
-9999999...+9999999
DoubleToS5Timer
10...9990000
DoubleToS5Float
+-1.701411e+38
1.3.3.5
Format adaptation sorted by AS data type
Introduction
When configuring external tags, another format adaptation must be done for all numeric data
types.
The data type determines the data format on the WinCC side. The format adaptation also
defines the conversion from WinCC format to the AS format. The definition applies for both
transfer directions.
Choose the required AS data type in the following selection box. You are then provided with
a list of the respective possible format adaptations and respective value ranges in the table
below.
AS data type
Format adaptation and value range
Table 1-9
AikenByte
Format adaptation "AikenByte"
Value range
ByteToAikenByte
0...99
CharToAikenByte
0...99
DoubleToAikenByte
0...99
DwordToAikenByte
0...99
FloatToAikenByte
0...99
LongToAikenByte
0...99
ShortToAikenByte
0...99
WordToAikenByte
0...99
28
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Table 1-10
AikenWord
Format adaptation "AikenWord"
Value range
ByteToAikenWord
0...255
CharToAikenWord
0...127
DoubleToAikenWord
0...9999
DwordToAikenWord
0...9999
FloatToAikenWord
0...9999
LongToAikenWord
0...9999
ShortToAikenWord
0...9999
WordToAikenWord
0...9999
Table 1-11
AikenDWord
Format adaptation "AikenDWord"
Value range
ByteToAikenDword
0...255
CharToAikenDword
0...127
DoubleToAikenDword
0...99999999
DwordToAikenDword
0...99999999
FloatToAikenDword
0 to 9.999999e+07
LongToAikenDword
0...99999999
ShortToAikenDword
0...32767
WordToAikenDword
0...65535
Table 1-12
BCDByte
Format adaptation "BCDByte"
Value range
ByteToBCDByte
0...99
CharToBCDByte
0...99
DoubleToBCDByte
0...99
DwordToBCDByte
0...99
FloatToBCDByte
0...99
LongToBCDByte
0...99
ShortToBCDByte
0...99
WordToBCDByte
0...99
Table 1-13
BCDWord
Format adaptation "BCDWord"
Value range
ByteToBCDWord
0...255
CharToBCDWord
0...127
DoubleToBCDWord
0...9999
DwordToBCDWord
0...9999
FloatToBCDWord
0...9999
LongToBCDWord
0...9999
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
29
Process communication
1.3 WinCC process communication
Format adaptation "BCDWord"
Value range
ShortToBCDWord
0...9999
WordToBCDWord
0...9999
Table 1-14
BCDDWord
Format adaptation "BCDDWord"
Value range
ByteToBCDDword
0...255
CharToBCDDword
0...127
DoubleToBCDDword
0...99999999
DwordToBCDDword
0...99999999
FloatToBCDDword
0 to 9.999999e+07
LongToBCDDword
0...99999999
ShortToBCDDword
0...32767
WordToBCDDword
0...65535
Table 1-15
Double
Format adaptation "Double"
Value range
DoubleToDouble
+-1.79769313486231e+308 (no conversion)
FloatToDouble
+-3.402823e+38
Table 1-16
ExcessByte
Format adaptation "ExcessByte"
Value range
ByteToExcessByte
0...99
CharToExcessByte
0...99
DoubleToExcessByte
0...99
DwordToExcessByte
0...99
FloatToExcessByte
0...99
LongToExcessByte
0...99
ShortToExcessByte
0...99
WordToExcessByte
0...99
Table 1-17
ExcessWord
Format adaptation "ExcessWord"
Value range
ByteToExcessWord
0...255
CharToExcessWord
0...127
DoubleToExcessWord
0...9999
DwordToExcessWord
0...9999
FloatToExcessWord
0...9999
LongToExcessWord
0...9999
ShortToExcessWord
0...9999
WordToExcessWord
0...9999
30
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Table 1-18
ExcessDWord
Format adaptation "ExcessDWord"
Value range
ByteToExcessDword
0...255
CharToExcessDword
0...127
DoubleToExcessDword
0...99999999
DwordToExcessDword
0...99999999
FloatToExcessDword
0 to 9.999999e+07
LongToExcessDword
0...99999999
ShortToExcessDword
0...32767
WordToExcessDword
0...65535
Table 1-19
ExtSignedBCDByte
Format adaptation "ExtSignedBCDByte"
Value range
CharToExtSignedBCDByte
-79...+79
DoubleToExtSignedBCDByte
-79...+79
FloatToExtSignedBCDByte
-79...+79
LongToExtSignedBCDByte
-79..+79
ShortToExtSignedBCDByte
-79...+79
Table 1-20
ExtSignedBCDWord
Format adaptation "ExtSignedBCDWord"
Value range
CharToExtSignedBCDWord
-128...+127
DoubleToExtSignedBCDWord
-7999...+7999
FloatToExtSignedBCDWord
-7999...+7999
LongToExtSignedBCDWord
-7999...+7999
ShortToExtSignedBCDWord
-7999...+7999
Table 1-21
ExtSignedBCDDWord
Format adaptation "ExtSignedBCDDWord"
Value range
CharToExtSignedBCDDword
-128...+127
DoubleToExtSignedBCDDword
-79999999...+79999999
FloatToExtSignedBCDDword
-7.999999e+07 to +7.999999e+07
LongToExtSignedBCDDword
-79999999...+79999999
ShortToExtSignedBCDDword
-32768...+32767
Table 1-22
Float
Format adaptation "Float"
Value range
DoubleToFloat
+-3.402823e+38
FloatToFloat
+-3.402823e+38 (no conversion)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
31
Process communication
1.3 WinCC process communication
Table 1-23
MSBByte
Format adaptation "MSBByte"
Value range
CharToMSBByte
-128...+127
DoubleToMSBByte
-127...+127
FloatToMSBByte
-127...+127
LongToMSBByte
-127...+127
ShortToMSBByte
-127...+127
Table 1-24
MSBWord
Format adaptation "MSBWord"
Value range
CharToMSBWord
-128...+127
DoubleToMSBWord
-32767...+32767
FloatToMSBWord
-32767...+32767
LongToMSBWord
-32767...+32767
ShortToMSBWord
-32767...+32767
Table 1-25
MSBDWord
Format adaptation "MSBDWord"
Value range
CharToMSBDword
-128...+127
DoubleToMSBDword
-2147483647...+2147483647
FloatToMSBDword
-2.147483e+09 to +2.147483e+09
LongToMSBDword
-2147483647...+2147483647
ShortToMSBDword
-32768...+32767
Table 1-26
S5Float
Format adaptation "S5Float"
Value range
DoubleToS5Float
+-1.701411e+38
FloatToS5Float
+-1.701411e+38
Table 1-27
S5Timer
Format adaptation "S5Timer"
Value range
DoubleToS5Timer
10...9990000
FloatToS5Timer
10...9990000
Table 1-28
SignedByte
Format adaptation "SignedByte"
Value range
ByteToSignedByte
0...127
CharToSignedByte
-128...+127 (no conversion)
DoubleToSignedByte
-128...+127
DwordToSignedByte
0...127
FloatToSignedByte
-128...+127
32
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Format adaptation "SignedByte"
Value range
LongToSignedByte
-128...+127
ShortToSignedByte
-128...+127
WordToSignedByte
0...127
Table 1-29
SignedWord
Format adaptation "SignedWord"
Value range
ByteToSignedWord
0...255
CharToSignedWord
-128...+127
DoubleToSignedWord
-32768...+32767
DwordToSignedWord
0...32767
FloatToSignedWord
-32768...+32767
LongToSignedWord
-32768...+32767
ShortToSignedWord
-32768...+32767 (no conversion)
WordToSignedWord
0...32767
Table 1-30
SignedDWord
Format adaptation "SignedDWord"
Value range
ByteToSignedDword
0...255
CharToSignedDword
-128...+127
DoubleToSignedDword
-2147483647...+2147483647
DwordToSignedDword
0...2147483647
FloatToSignedDword
-2.147483e+09 to +2.147483e+09
LongToSignedDword
-2147483647...+2147483647 (no conversion)
ShortToSignedDword
-32768...+32767
WordToSignedDword
0...65535
Table 1-31
SignedAikenByte
Format adaptation "SignedAikenByte"
Value range
CharToSignedAikenByte
-9...+9
DoubleToSignedAikenByte
-9...+9
FloatToSignedAikenByte
-9...+9
LongToSignedAikenByte
-9...+9
ShortToSignedAikenByte
-9...+9
Table 1-32
SignedAikenWord
Format adaptation "SignedAikenWord"
Value range
CharToSignedAikenWord
-128...+127
DoubleToSignedAikenWord
-999...+999
FloatToSignedAikenWord
-999...+999
LongToSignedAikenWord
-999...+999
ShortToSignedAikenWord
-999...+999
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
33
Process communication
1.3 WinCC process communication
Table 1-33
SignedAikenDWord
Format adaptation "SignedAikenDWord"
Value range
CharToSignedAikenDword
-128...+127
DoubleToSignedAikenDword
-9999999...+9999999
FloatToSignedAikenDword
-9999999...+9999999
LongToSignedAikenDword
-9999999...+9999999
ShortToSignedAikenDword
-32768...+32767
Table 1-34
SignedBCDByte
Format adaptation "SignedBCDByte"
Value range
CharToSignedBCDByte
-9...+9
DoubleToSignedBCDByte
-9...+9
FloatToSignedBCDByte
-9...+9
LongToSignedBCDByte
-9...+9
ShortToSignedBCDByte
-9...+9
Table 1-35
SignedBCDWord
Format adaptation "SignedBCDWord"
Value range
CharToSignedBCDWord
-128...+127
DoubleToSignedBCDWord
-999...+999
FloatToSignedBCDWord
-999...+999
LongToSignedBCDWord
-999...+999
ShortToSignedBCDWord
-999...+999
Table 1-36
SignedBCDDWord
Format adaptation "SignedBCDDWord"
Value range
CharToSignedBCDDword
-128...+127
DoubleToSignedBCDDword
-9999999...+9999999
FloatToSignedBCDDword
-9999999...+9999999
LongToSignedBCDDword
-9999999...+9999999
ShortToSignedBCDDword
-32768...+32767
Table 1-37
SignedExcessByte
Format adaptation "SignedExcessByte"
Value range
CharToSignedExcessByte
-9...+9
DoubleToSignedExcessByte
-9...+9
FloatToSignedExcessByte
-9...+9
LongToSignedExcessByte
-9...+9
ShortToSignedExcessByte
-9...+9
34
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
Table 1-38
SignedExcessWord
Format adaptation "SignedExcessWord"
Value range
CharToSignedExcessWord
-128...+127
DoubleToSignedExcessWord
-999...+999
FloatToSignedExcessWord
-999...+999
LongToSignedExcessWord
-999...+999
ShortToSignedExcessWord
-999...+999
Table 1-39
SignedExcessDWord
Format adaptation "SignedExcessDWord"
Value range
CharToSignedExcessDword
-128...+127
DoubleToSignedExcessDword
-9999999...+9999999
FloatToSignedExcessDword
-9999999...+9999999
LongToSignedExcessDword
-9999999...+9999999
ShortToSignedExcessDword
-32768...+32767
Table 1-40
SimaticCounter
Format adaptation "SimaticCounter"
Value range
WordToSimaticCounter
0...999
Table 1-41
SimaticBCDCounter
Format adaptation "SimaticBCDCounter"
Value range
WordToSimaticBCDCounter
0...999
Table 1-42
SimaticTimer
Format adaptation "SimaticTimer"
Value range
DwordToSimaticTimer
10...9990000
LongToSimaticTimer
10...9990000
Table 1-43
SimaticBCDTimer
Format adaptation "SimaticBCDTimer"
Value range
DwordToSimaticBCDTimer
10...9990000
LongToSimaticBCDTimer
10...9990000
Table 1-44
UnsignedByte
Format adaptation "UnsignedByte"
Value range
ByteToUnsignedByte
0...255 (no conversion)
CharToUnsignedByte
0...127
DoubleToUnsignedByte
0...255
DwordToUnsignedByte
0...255
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
35
Process communication
1.3 WinCC process communication
Format adaptation "UnsignedByte"
Value range
FloatToUnsignedByte
0...255
LongToUnsignedByte
0...255
ShortToUnsignedByte
0...255
WordToUnsignedByte
0...255
Table 1-45
UnsignedWord
Format adaptation "UnsignedWord"
Value range
ByteToUnsignedWord
0...255
CharToUnsignedWord
0...127
DoubleToUnsignedWord
0...65535
DwordToUnsignedWord
0...65535
FloatToUnsignedWord
0...65535
LongToUnsignedWord
0...65535
ShortToUnsignedWord
0...32767
WordToUnsignedWord
0...65535 (no conversion)
Table 1-46
UnsignedDWord
Format adaptation "UnsignedDWord"
Value range
ByteToUnsignedDword
0...255
CharToUnsignedDword
0...127
DoubleToUnsignedDword
0...4294967295
DwordToUnsignedDword
0...4294967295 (no conversion)
FloatToUnsignedDword
0 to 4.294967e+09
LongToUnsignedDword
0...2147483647
ShortToUnsignedDword
0...32767
WordToUnsignedDword
0...65535
1.3.3.6
Principle of the BinWrite-Mechanism
Introduction
In WinCC, not all communication drivers and their channel units support the direct bit-wise or
byte-wise access (short: Bit-/Byte-access) to address ranges in a connected automation
system. Instead, they use the BinWrite mechanism.
Bit-/Byte-access
With channel units of communication drivers with bit-/byte-access, the desired bit or byte can
be read and written directly.
In the following figure, a bit x is allocated the value = 1 via direct bit-/byte-access.
36
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
BinWrite Mechanism
The following communication drivers do not support bit-/byte-access and instead use the
BinWrite mechanism for the respective channel units:
● Modbus Serial
● SIMATIC S5 Ethernet Layer 4
● SIMATIC S5 Programmers Port AS511
● SIMATIC S5 Serial 3964R
● SIMATIC TI Ethernet Layer 4
● SIMATIC TI Serial
To write a bit or byte, the channel unit first reads the entire data word with the BinWrite
mechanism. The data to be addressed is then changed in the word that is read. Then, instead
of just the changed bit or byte, the entire (!) word is written back.
In the following figure, a bit x is allocated the value = 1 via the BinWrite mechanism.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
37
Process communication
1.3 WinCC process communication
Note
If a data word changes in an AS at the same time as this data word was read via the BinWrite
mechanism in the WinCC (see figure "Problem case"), then the change is lost in the AS, as
soon as WinCC writes the data word back.
1.3.3.7
How to Configure a Tag with "BinWrite"
Introduction
If you want to configure a "Binary tag" for the channel unit of a communication driver, which
does not support bit-/byte-access, you have to activate and configure the BinWrite mechanism
using a dialog, which otherwise does not exist.
Requirements
● The required communication processor and the hardware driver are installed.
● The desired communication driver, which does not support bit-/byte-access however, is
installed, e.g. "SIMATIC S5 Ethernet Layer 4".
● A connection has already been created based on its channel units.
Procedure
1. Select entry "New tag..." in the context menu of the connection that you want to create a
new tag for. The "Create new tag" dialog is displayed.
2. Enter a tag name that is unique within the project in the "Name" field on the General tab.
Select "Binary tag", "Unsigned 8 bit value" or "Signed 8 bit value" as data type.
38
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Process communication
1.3 WinCC process communication
3. Click the "Select" button to open dialog "Bit-/Byte tag". (Setting the address range in the
AS is done with this button for channels with bit-/byte access.)
4. Activate the checkbox "Access to one bit" or "Access to one byte" and make the normal
settings. The display in this dialog depends on the data type selected in step 2.
5. Close the dialog by clicking "OK".
Note
The dialog is also opened if you neglect to activate the BinWrite mechanism for a new "Binary
tag" or 8 bit tag. If you want to close the "Create new tag" window again immediately with
"OK", you will get error message "The address parameter is invalid". Acknowledge the dialog
with "YES". This opens the dialog "Bit-/Byte tag" and you can repeat the settings this way.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
39
Process communication
1.3 WinCC process communication
1.3.4
Port Addresses for Coupling via Ethernet
Port Addresses
CAUTION
Ethernet communication
When using Ethernet-based communication, the end users is responsible for the security of
his/her own data network. If targeted attacks lead to an overload of the device for instance,
the functionality is no longer guaranteed.
When connected via Ethernet, you may require information on the port addresses. This
information is required for configuring a firewall or a router. The port addresses that WinCC
applications use as defaults are shown in the table.
Port address
TCP/IP
40
S7 Communication
102
HTTP (communication; transfer)
80
HTTPS (communication; transfer)
443
WebServices (SOAP)
80 HTTP
443 HTTPS
OPC-XML (CE as OPC Master)
80 HTTP
443 HTTPS
SendEmail
25
Transfer (via Ethernet; CE-Stub; PC Loader; PC)
2308
alternative 50523
Logging (via Ethernet) CSV File
139, 445
Modbus Ethernet
502
Allen-Bradley Ethernet CIP
44818
Allen-Bradley Ethernet CSP2
2222
Port address
UDP
137, 138
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.1
2
WinCC Channel "Allen Bradley - Ethernet IP"
Introduction
The channel "Allen Bradley - Ethernet IP" is used for linking to Allen-Bradley automation
systems. The communication is handled with the Ethernet IP protocol.
Depending on the communication hardware used, the system supports connections via the
following channel units:
● Allen Bradley E/IP PLC5
● Allen Bradley E/IP SLC50x
● Allen Bradley E/IP ControlLogix
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
41
Allen Bradley - Ethernet IP
2.2 Channel Unit Assignment
2.2
Channel Unit Assignment
Introduction
The channel unit must be selected for the channel in order to create a connection from WinCC
to an existing or planned network.
Channel Unit Assignment
The following table shows an allocation of the channel units of channel "Allen Bradley - Ethernet
IP" to the network and automation system (AS).
42
Channel Unit of the Channel
Communication Network
AS
Allen Bradley E/IP PLC5
Ethernet IP
PLC-5 with Ethernet Port
Allen Bradley E/IP SLC50x
Ethernet IP
SLC 500 with Ethernet Port, e.g.
SLC 5/05
Allen Bradley E/IP ControlLogix
Ethernet IP
ControlLogix 5500
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.3 Supported Data Types
2.3
Supported Data Types
Introduction
Define the required tags for a logical connection. The following data types are supported by
the "Allen Bradley - Ethernet IP" channel:
● Binary Tag
● Signed 8-bit value
● Unsigned 8-bit value
● Signed 16-bit value
● Unsigned 16-bit value
● Signed 32-bit value
● Unsigned 32-bit value
● Floating-point number 32-bit IEEE 754
● Floating-point number 64-bit IEEE 754
● Text tag 8-bit character set
● Text tag 16-bit character set
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
43
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
2.4
Configuring the Channel
2.4.1
Configuring the Channel "Allen Bradley - Ethernet IP"
Introduction
WinCC needs a logical connection for communication of WinCC with the automation system
(AS). This section shows how the "Allen Bradley - Ethernet IP" channel is configured.
When implementing the TCP/IP protocol, you must define the IP address of the AS for the
logic connection. The IP address consists of four numerical values, separated by dots. The
numerical values must be within the range of 0-255.
Note
Timeout Behavior
Interrupted connections are not detected immediately when using the TCP/IP protocol. The
check-back message can take up to a minute.
Connectable controllers
Connections can be implemented for the following Allen-Bradley PLCs:
● Allen-Bradley ControlLogix 5500
● Allen-Bradley CompactLogix 5300
● PLC-5 with Ethernet Port
● SLC 500 with Ethernet Port, e.g. SLC 5/05
● MicroLogix
Released communication types
The following types of communication are system-tested and released for the "Allen Bradley
- Ethernet IP" channel:
● Point-to-point connection:
● Multiple point connection from the WinCC station with an optional amount of controllers.
Online Configuration
The online configuration of the "Allen Bradley - Ethernet IP" channel is not supported.
44
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
2.4.2
How to configure a "Allen Bradley E/IP PLC5" channel unit connection
Introduction
The following steps are required for configuring a connection of the "Allen Bradley E/IP PLC5"
channel unit:
1. Configuring a connection
2. Configuring Tags
Requirements
● The communication driver for channel "Allen Bradley - Ethernet IP" is installed and
integrated into the project.
Procedure
1. Select the entry "New Connection" in the pop-up menu of the "Allen Bradley E/IP PLC5"
channel unit. The "Connection Properties" dialog is opened.
2. Enter a connection name in the "General" tab.
3. Click on the "Properties" button to open the "Allen Bradley E/IP Connection Parameters"
dialog.
4. Enter the IP address of the Ethernet/IP module of the controller. Port 44818 is permanently
set by default for Ethernet/IP devices.
5. Define the CIP path from the Ethernet module to the controller in the "Communication path"
field. This setting creates a logical interconnection of the Ethernet module with the PLC,
irrespective of their location in different CIP networks.
6. Close both of the dialogs by clicking the "OK" button.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
45
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
2.4.3
How to configure an "Allen Bradley E/IP SLC50x" channel unit connection
Introduction
The following steps are required for configuring a connection of the "Allen Bradley E/IP
SLC50x" channel unit:
1. Configuring a connection
2. Configuring Tags
Requirements
● The communication driver for channel "Allen Bradley - Ethernet IP" is installed and
integrated into the project.
Procedure
1. Select the entry "New Connection" in the pop-up menu of the "Allen Bradley E/IP SLC50x"
channel unit. The "Connection Properties" dialog is opened.
2. Enter a connection name in the "General" tab.
3. Click on the "Properties" button to open the "Allen Bradley E/IP Connection Parameters"
dialog.
4. Enter the IP address of the Ethernet/IP module of the controller. Port 44818 is permanently
set by default for Ethernet/IP devices.
5. Define the CIP path from the Ethernet module to the controller in the "Communication path"
field. This setting creates a logical interconnection of the Ethernet module with the PLC,
irrespective of their location in different CIP networks.
6. Close both of the dialogs by clicking the "OK" button.
46
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
2.4.4
How to configure an "Allen Bradley E/IP ControlLogix" channel unit connection
Introduction
The following steps are required for configuring a connection of the "Allen Bradley E/IP
ControlLogix" channel unit:
1. Configuring a connection
2. Configuring Tags
Requirements
● The communication driver for channel "Allen Bradley - Ethernet IP" is installed and
integrated into the project.
Procedure
1. Select the entry "New Connection" in the pop-up menu of the "Allen Bradley E/IP
ControlLogix" channel unit. The "Connection Properties" dialog is opened.
2. Enter a connection name in the "General" tab.
3. Click on the "Properties" button to open the "Allen Bradley E/IP Connection Parameters"
dialog.
4. Enter the IP address of the Ethernet/IP module of the controller. Port 44818 is permanently
set by default for Ethernet/IP devices.
5. Define the CIP path from the Ethernet module to the controller in the "Communication path"
field. This setting creates a logical interconnection of the Ethernet module with the PLC,
irrespective of their location in different CIP networks.
6. Close both of the dialogs by clicking the "OK" button.
2.4.5
Examples: Communication path
Example 1:
Connection with a PLC in the same Allen-Bradley rack.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
47
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
1,0
Number
Meaning
1
Stands for a backplane connection.
0
Stands for a CPU slot number.
Example 2:
Connection with a PLC in remote Allen-Bradley racks. Two Allen-Bradley racks are networked
on Ethernet.
1,2,2,190.130.3.101,1,5
Number
Meaning
1
Backplane connection
2
Stands for the CPU slot number of the second Ethernet module.
2
Stands for an Ethernet connection.
190.130.3.101
IP address of a remote AB rack on the network – in particular the third Ethernet
module
1
Backplane connection
5
Slot number of the CPU
2.4.6
Configuring the tags
2.4.6.1
Configuring the tags
Introduction
For a connection between WinCC and the automation system (AS) via channel "Allen Bradley
- Ethernet IP", tags of different data types can be created in WinCC. The permitted data types
are listed in this section.
Tag Updating
If the tags are retrieved simultaneously in a picture from a PLC, the "Allen Bradley - Ethernet
IP" channel attempts to optimize the update. This can only be accomplished under the following
conditions however:
● - the tags are in the same address range.
● - the tags are as close to one another as possible within the address range.
If you do not observe these recommendations, it can lead to noticeable differences in the
picture refresh with large amounts of tags. The acquisition cycles may not be maintained under
certain circumstances.
48
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
The best performance for the connection is achieved if you observe the following rules when
configuring the tags:
● Update of maximum 2000 tags simultaneously.
● Combine the tags in the least possible space, best in only one address range.
Permitted data types
The selection of data types listed below can be used to configure tags.
Basic data types
Data type
Bit address space
Bool
-
SInt
0-7
USInt
0-7
Int
0-15
UInt
0-15
DInt
0-31
UDInt
0-31
Real
-
String
-
Address
Permitted data types
Array
SInt, USInt, Int, UInt, DInt, UDInt, Real
Arrays
2.4.6.2
Addressing
Addressing
A tag is uniquely referenced in WinCC by means of an address in the controller. The address
must correspond with the tag name in the PLC. The tag address is defined by a string with a
length of up to 128 characters.
Using characters for addressing
Valid characters for tag addressing:
● Letters (a to z, A to Z)
● Numbers (0 to 9)
● Underscore ( _ )
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
49
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
The tag address consists of tag name and other character strings used to specify the tag in
the PLC.
Tag name properties:
● The tag name may begin but not end with an underscore character.
● Strings with successive underscore and space characters are invalid.
● The address may not exceed a length of 128 characters.
Note
The characters reserved for tag addressing may not be used in program/tag names or at
any other address instance.
The reserved characters are listed below:
Reserved character
Function
.
Element delimiter
:
Definition of a program tag
,
Delimiter for addressing multi-dimensional arrays
/
Reserved for bit addressing.
[]
Addressing of array elements or arrays
Controller and program tags
The "Allen-Bradley E/IP ControlLogix" allows addressing of PLC tags (global project tags) and/
or program tags (global program tags). Program tags are declared via the program names in
the controller and the actual tag names. Controller variables are addressed by their names.
Note
Addressing errors
Addressing errors are generated when the tag name and data type are inconsistent.
The tag name defined in the address field in WinCC must correspond with the tag name in
the controller. The data type of tags in WinCC and in the controller must correspond.
Note
You cannot address module-specific Tags, such as data at input and output modules, directly.
Use an Alias tag in the controller instead.
Example: Local:3:O.data cannot be addressed in WinCC
If, for Local:3:O in the controller, the alias "MyOut" is defined, you can address with WinCC
via MyOut.Data.
50
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
2.4.6.3
Addressing syntax
Notation of addresses
The following tables define the possibilities for writing individual addressing.
Table 2-1
Access to arrays, basic data types and structure elements
Data types
Type
Address
Basic data types
PLC tag
Tag name
Program tag
Programname:tagname
PLC tag
Array tag
Program tag
Program name: array tag
PLC tag
Tagname/bitnumber
Program tag
Programname:tagname/bitnumber
PLC tag
Structure tag. Structure element
Program tag
Program name: structure tag. structure element
Arrays
Bits
Structure elements
Note
Bit addressing with the data types Bool, Real and String is not permitted and will cause an
addressing fault.
Description of the syntax
Syntax description:
(Programname:)tagname([x(,y)(,z)]){.tagname([x(,y)(,z)])}(/
bitnumber)
● The "( )" defines an optional, single instance of an expression.
● The "{ }" defines an optional expression with multiple single instances.
The address string length may not exceed 128 characters.
2.4.6.4
Addressing Types
Array elements
Elements of one-dimensional, two-dimensional and three-dimensional arrays in the PLC are
indexed by setting an index and the corresponding notation in the tag editor. Array addressing
starts at element "0", with arrays of all basic types being valid for element addressing. Read/
write operations are only carried out at the addressed element, and not for the entire array.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
51
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
Bits and bit tags
Bit access is allowed to all basic data types with the exception of Bool, Real and String. Bit
addressing is also allowed at array/structure elements. Data type Bool is defined in WinCC for
addressing bits and bit tags in the basic data types.
One-place bit numbers will be address with "/x" or "/0x" (x = bit number). Bit numbers are
defined by up to two digits.
Note
With the "Bool" data type in the data types SInt, Int and DInt, after changing the specified bit
the complete tag is then written in the PLC again. In the meantime, no check is made as to
whether other bits in the tag have since changed. Therefore, the PLC may have only read
access to the specified tag.
Structures
User-defined data types are created by means of structures. These structures group tags of
different data types. Structures may consist of basic types, arrays and of other structures. In
WinCC, only basic data types are addressed as structure elements and not entire structures.
Structure elements
Structure elements are addressed by means of the name of the structure and of the required
structure element. This addressing is separated by point. In addition to basic data types, the
structure elements may represent arrays or other structures. Only one-dimensional arrays may
be used as a structure element.
Note
The nesting depth of structures is only limited by the maximum length of 128 characters for
the address.
2.4.6.5
Examples for Addressing
Example of a table for addressing
The following table shows basic addressing variations for control variables. Other addressing
variants are possible by means of combination.
Type
Type
Address
General
PLC tag
Tag name
Program tag
Program:tagname
Array
52
Access to an element of a 2- Arraytag[Dim1,Dim2]
dimensional array
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
Type
Structure
Type
Address
Element of a structure array
(1-dimensional)
Arraytag[Dim1].structureelement
Bit in element of a basic type
array (2-dimensional)
Arraytag[Dim1,Dim2]/Bit
Array in structure
Structuretag.arraytag
Bit in element of an array in
a sub-structure
Structuretag.structure2.arraytag [element]/
bit
Note
Program tags are addressed by leading the address with the program name derived from the
PLC with colon delimiter.
Example: Programname:arraytag[Dim1,Dim2]
Access to array elements
Type
Address
PLC tag
Arraytag[Dim1]
Arraytag[Dim1,Dim2]
Arraytag[Dim1,Dim2,Dim3]
Program tag
Programname:arraytag[Dim1]
Programname:arraytag[Dim1,Dim2]
Programname:arraytag[Dim1,Dim2,Dim3]
2.4.6.6
How to configure a tag for the Allen Bradley E/IP ControlLogix channel unit
Introduction
This section shows how you configure a tag for channel unit "Allen Bradley E/IP ControlLogix"
in the automation system (AS) address range.
Requirements
● The channel "Allen Bradley - Ethernet IP" must be integrated in the project.
● A connection must be created in the "Allen Bradley E/IP ControlLogix" channel unit.
Procedure
1. Select "New Tag" from the shortcut menu of the Ethernet IP connection. The "Tag
properties" dialog box opens.
2. Enter the name of the tag in the "Name" field. Select the desired data type in the "Data
type" field.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
53
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
3. The "Select" button opens the dialog "Allen Bradley ControlLogix Variable".
4. Enter the address of the tags in AS in the "Address" field.
Note
Addressing errors
Addressing errors are generated when the tag name and data type are inconsistent.
The tag name defined in the address field in WinCC must correspond with the tag name
in the controller. The data type of tags in WinCC must correspond with the data types in
the controller.
5. Close both of the dialogs by clicking the "OK" button.
2.4.6.7
How to configure a tag with bit by bit access for Allen Bradley E/IP PLC5 or SLC50x
Introduction
This section shows you how to configure a tag for bit by bit access for the address area in the
automation system (AS).
Requirements
● The channel "Allen Bradley - Ethernet IP" must be integrated in the project.
● A connection must be created in the "Allen Bradley E/IP PLC5" or "Allen Bradley E/IP
SLC50x" channel unit.
Procedure
1. Select "New Tag" from the shortcut menu of the Ethernet IP connection. The "Tag
properties" dialog box opens.
2. Enter the name of the tag in the "Name" field. Select the desired data type in the "Data
type" field.
54
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
3. The "Select" button opens the dialog "Allen Bradley PLC/SLC Tag".
4. Select an address range in the "File" field. Entries N, R, C, T, B, S, I, O, D, A, ST are
available.
5. Enter the "File Number" if it is different from the suggested file number.
6. Enter the "Element".
7. Depending on the setting in the "File" field, define the "Bit" to address or select a value for
"Bit (octal)" or "Sub".
8. Close both of the dialogs by clicking the "OK" button.
2.4.6.8
How to configure a tag with byte by byte access for Allen Bradley E/IP PLC5 or SLC50x
Introduction
This section shows you how to configure a tag for byte by byte access for the address area in
the automation system (AS).
Requirements
● The channel "Allen Bradley - Ethernet IP" must be integrated in the project.
● A connection must be created in the "Allen Bradley E/IP PLC5" or "Allen Bradley E/IP
SLC50x" channel unit.
Procedure
1. Select "New Tag" from the shortcut menu of the Ethernet IP connection. The "Tag
properties" dialog box opens.
2. Enter the name of the tag in the "Name" field. Select the desired data type in the "Data
type" field.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
55
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
3. The "Select" button opens the dialog "Allen Bradley PLC/SLC Tag".
4. Select the A or ST address range in the "File" field.
5. Enter the "File Number" if it is different from the suggested file number.
6. Enter the "Element".
7. Close both of the dialogs by clicking the "OK" button.
2.4.6.9
How to configure a tag with word by word access for Allen Bradley E/IP PLC5 or SLC50x
Introduction
This section shows you how to configure a tag for word by word access for the address area
in the automation system (AS).
Requirements
● The channel "Allen Bradley - Ethernet IP" must be integrated in the project.
● A connection must be created in the "Allen Bradley E/IP PLC5" or "Allen Bradley E/IP
SLC50x" channel unit.
Procedure
1. Select "New Tag" from the shortcut menu of the Ethernet IP connection. The "Tag
properties" dialog box opens.
2. Enter the name of the tag in the "Name" field. Select the desired data type in the "Data
type" field.
56
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
3. The "Select" button opens the dialog "Allen Bradley PLC/SLC Tag".
4. Select the address range in the "File" field. Entries N, R, C, T, B, S, I, O, D, A and ST are
available.
5. Enter the "File Number" if it is different from the suggested file number. The File number
cannot be changed for the setting "S".
6. Enter the "Element".
7. Select one of the values for the "Sub" field if it is displayed. This depends on the setting
made in the "File field.
8. Close both of the dialogs by clicking the "OK" button.
2.4.6.10
How to configure a text tag for Allen Bradley E/IP PLC5 or SLC50x
Introduction
This section shows you how to configure a tag for word by word access for the address area
in the automation system (AS).
Requirements
● The channel "Allen Bradley - Ethernet IP" must be integrated in the project.
● A connection must be created in the "Allen Bradley E/IP PLC5" or "Allen Bradley E/IP
SLC50x" channel unit.
Procedure
1. Select "New Tag" from the shortcut menu of the Ethernet IP connection. The "Tag
properties" dialog box opens.
2. Enter the name of the tag in the "Name" field. Select the desired data type in the "Data
type" field.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
57
Allen Bradley - Ethernet IP
2.4 Configuring the Channel
3. The "Select" button opens the dialog "Allen Bradley PLC/SLC Tag".
4. Select the A or ST address range in the "File" field.
5. Enter the "File Number" if it is different from the suggested file number. The File number
cannot be changed for the setting "S".
6. Enter the "Element".
7. Select one of the values for the "Sub" field if it is displayed. This depends on the setting
made in the "File field.
8. Close both of the dialogs by clicking the "OK" button.
58
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Mitsubishi Ethernet
3.1
3
WinCC channel "Mitsubishi Ethernet"
Introduction
The "Mitsubishi Ethernet" channel is intended for communication between a WinCC station
and Mitsubishi controllers of the FX3U and Q series. The communication takes place via the
MELSEC communication protocol (MC protocol).
Channel units
The "Mitsubishi Ethernet" channel comes equipped with the "Mitsubishi FX3U Series" and
"Mitsubishi Q Series" channel units.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
59
Mitsubishi Ethernet
3.2 Supported data types
3.2
Supported data types
Introduction
Define the required tags for a logical connection between WinCC and a connected controller.
The following data types are supported by the "Mitsubishi Ethernet" channel:
● Binary Tag
● Signed 16-bit value
● Unsigned 16-bit value
● Signed 32-bit value
● Unsigned 32-bit value
● Floating-point number 32-bit IEEE 754
● Floating-point number 64-bit IEEE 754
● Text tag 8-bit character set
● Text tag 16-bit character set
● Raw Data Tag
60
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Mitsubishi Ethernet
3.3 Configuring the Channel
3.3
Configuring the Channel
3.3.1
Configuring the "Mitsubishi Ethernet" channel
Introduction
WinCC needs a logical connection for communication of WinCC with the automation system
(AS). This section illustrates how to configure the "Mitsubishi Ethernet" channel.
You can establish a connection to an AS with either TCP/IP or UDP/IP protocol. Therefore,
you have to enter the IP address and IP port number for the AS when configuring a logical
connection for the channel "Mitsubishi Ethernet" and select either the UDP or TCP/IP protocol.
The IP address consists of four numerical values, separated by dots. The numerical values
must be within the range 0 to 255.
Note
Timeout Behavior
Interrupted connections are not detected immediately when using the TCP/IP protocol. The
feedback can take longer and is dependent on the operating system.
Mitsubishi controllers that are supported
You can configure logical connections for the following Mitsubishi controllers:
● MELSEC FX3U series
● MELSEC System Q
When you configure the connections and tags, the procedure is identical for both controller
families. The configuration differs only in relation to the used address type of the specific
controller family. In addition, the routing of information is only supported by MELSEC System
Q models.
Online Configuration
The "Mitsubishi Ethernet channel supports the online configuration of tags and connections.
3.3.2
How to configure a "Mitsubishi FX3U Series" channel unit connection
Introduction
The following steps are required for configuring the "Mitsubishi Ethernet" channel.
1. Configuring a connection
2. Configuring tags
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
61
Mitsubishi Ethernet
3.3 Configuring the Channel
This section shows you how to configure the connection for the "Mitsubishi FX3U Series"
channel unit.
Requirements
● The communication driver for the "Mitsubishi Ethernet" channel is installed and integrated
into the project.
Note
When you use Mitsubishi controllers, you will also have to configure the connections in
the controller. To do this, follow the operating instructions provided by the manufacturer.
Procedure
1. Open the menu structure for the "Mitsubishi Ethernet" communication driver in the "Tag
Management" editor of the WinCC Explorer.
2. Select the entry "New Connection" in the shortcut menu of the "Mitsubishi FX3U Series"
channel unit. The "Connection Properties" dialog is opened.
3. Enter the name of the connection.
4. Click the "Properties" button to open the "Connection properties" dialog.
5. Enter the IP address of the controller.
6. Enter the port you want to use for the TCP/IP connection.
The valid range of values is from 0 to 65535.
7. Select the protocol to be used, "TCP" or "UDP".
Note
We recommend that you use the default protocol "UDP". The timeout behavior is better
with this protocol. Only use TCP if you are not able to use UDP.
62
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Mitsubishi Ethernet
3.3 Configuring the Channel
8. Enter the PC number.
If you do not want to enter a PC number, you must enter the value 255 or 0.
9. To establish the connection, select "Establish connection".
10.Close each dialog box by clicking "OK."
3.3.3
How to configure a "Mitsubishi Q Series" channel unit connection
Introduction
The following steps are required for configuring the "Mitsubishi Ethernet" channel.
1. Configuring a connection.
2. Configuring tags.
This section shows you how to configure the connection for the "Mitsubishi Q Series" channel
unit.
Requirements
● The communication driver for the "Mitsubishi Ethernet" channel is installed and integrated
into the project.
Note
When you use Mitsubishi controllers, you will also have to configure the connections in
the controller. To do this, follow the operating instructions provided by the manufacturer.
Procedure
1. Open the menu structure for the "Mitsubishi Ethernet" communication driver in the "Tag
Management" editor of the WinCC Explorer.
2. Select the entry "New Connection" in the shortcut menu of the "Mitsubishi Q Series" channel
unit. The "Connection Properties" dialog is opened.
3. Enter the name of the connection.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
63
Mitsubishi Ethernet
3.3 Configuring the Channel
4. Click the "Properties" button to open the "Connection properties" dialog.
5. Enter the IP address of the controller.
6. Enter the port you want to use for the TCP/IP connection.
The valid range of values is from 0 to 65535.
7. Select the protocol to be used, "TCP" or "UDP".
Note
We recommend that you use the default protocol "UDP". The timeout behavior is better
with this protocol. Only use TCP if you are not able to use UDP.
8. Enter the network number.
The default setting is 0.
9. Enter the PC number.
If you do not want to enter a PC number, you must enter the value 255 or 0.
10.To establish the connection, select "Establish connection".
11.Close each dialog box by clicking "OK."
3.3.4
Configuring the tags
3.3.4.1
Configuring the tags
Introduction
Tags of different data types can be created in WinCC for a connection between WinCC and
the automation system via the "Mitsubishi Ethernet" channel.
The following sections describe how to configure the tags.
64
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Mitsubishi Ethernet
3.3 Configuring the Channel
Address types, address ranges and data types
The table lists the address types, address ranges and data types that can be used when
configuring tags and structured tags. In addition, it is also specified which automation system
(AS) the respective address type supports. "FX" here stands for the MELSEC FX3 U series
and "Q" for the MELSEC Q system.
Note
If you want to use a specific WinCC data type, you have to consider the selected address
type; for example, address type "D" does not support the WinCC data type "Binary".
Address type
Code
Address range
Display
Data type
AS that are
supported
Input relays
X
000000...001FFF
Hex. (FX:Octal)
Bit
FX, Q
Output relays
Y
000000...001FFF
Hex. (FX: Octal)
Bit
FX, Q
Bit memories
M
0...8191
Decimal
Bit
FX, Q
Latch relay
L
0...8191
Decimal
Bit
Q
Error bit memory
F
0...2047
Decimal
Bit
Q
Edge relay
V
0...2047
Decimal
Bit
Q
Link relay
B
000000...001FFF
Hex.
Bit
Q
Data register
D
0...12287
Decimal
Word
FX, Q
Link register
W
000000...001FFF
Hex.
Word
Q
Timer (contact)
TS
0...2047
Decimal
Bit
FX, Q
Timer (OUT coil)
TC
0...2047
Decimal
Bit
Q
Timer (current value)
TN
0...2047
Decimal
Word
FX, Q
Retentive timer
(contact)
SS
0...2047
Decimal
Bit
Q
Retentive timer (coil)
SC
0...2047
Decimal
Bit
Q
Retentive timer (value)
SN
0...2047
Decimal
Word
Q
Counter / Contact
CS
0...1023
Decimal
Bit
FX, Q
Counter / Coil
CC
0...1023
Decimal
Bit
Q
Counter / current value
CN
0...1023
Decimal
Word
FX, Q
Expansion register
R
0...65535
Decimal
16-bit
FX, Q
Special link relay
SB
000000...0007FF
Hex.
Bit
Q
Special link register
SW
000000...0007FF
Hex.
Word
Q
Step flags
S
0...8191
Decimal
Bit
Q
Input relay (direct)
DX
000000...001FFF
Hex.
Bit
Q
Output relay (direct)
DY
000000...001FFF
Hex.
Bit
Q
Index register
Z
0...15
Decimal
Word
Q
Diagnostic bit memory
SM
0...2047
Decimal
Bit
Q
Diagnostic register
SD
0...2047
Decimal
Word
Q
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
65
Mitsubishi Ethernet
3.3 Configuring the Channel
3.3.4.2
How to configure a tag
Introduction
This section shows you how to configure a tag access for the address range in the automation
system (AS).
Requirements
● The "Mitsubishi Ethernet" channel is integrated in the project.
● A connection is established in the "Mitsubishi FX3U Series" or "Mitsubishi Q Series" channel
unit.
Procedure
1. Select the "New Tag" entry in the shortcut menu of the Mitsubishi Ethernet connection.
The "Tag properties" dialog box opens.
2. Enter the tag name.
3. Set the required data type.
4. Click the "Select" button to open the "Address properties" dialog.
5. Set the address type.
6. Enter the corresponding data element. The value depends on the configuration of the
controller.
7. If necessary, enter the raw data length.
66
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Mitsubishi Ethernet
3.3 Configuring the Channel
8. Close the "Address properties" dialog by clicking "OK".
The address of the tag is displayed in the "Address" field of the "Tag properties" dialog.
The address is adjusted to the data format of the AS.
9. Close the "Tag properties" dialog by clicking "OK".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
67
Modbus TCPIP
4.1
4
"Modbus TCP/IP" channel
Introduction
The "Modbus TCPIP" channel is for communication between a WinCC station and PLCs that
support Modbus via Ethernet. The communication is handled with the Modbus TCP/IP protocol.
Channel units
The "Modbus TCPIP" channel comes with the "Modbus TCP/IP Unit #1" channel unit.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
69
Modbus TCPIP
4.2 Supported Data Types
4.2
Supported Data Types
Introduction
Define the required tags for a logical connection with a connected controller. The following
data types are supported by the "Modbus TCPIP" channel:
● Binary tag
● Signed 16-bit value
● Unsigned 16-bit value
● Signed 32-bit value
● Unsigned 32-bit value
● Floating-point number 32-bit IEEE 754
● Text tag 8-bit character set
● Text tag 16-bit character set
70
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Modbus TCPIP
4.3 Configuring the Channel
4.3
Configuring the Channel
4.3.1
Configuring the "Modbus TCPIP" Channel
Introduction
WinCC needs a logical connection for communication of WinCC with the automation system
(AS). This section describes the communication with the "Modbus TCP/IP Unit #1" channel
unit. All connection-specific parameters are defined during the setup.
When implementing the TCP/IP protocol, you must define the IP address of the AS for the
logic connection. The IP address consists of four numerical values, separated by dots. The
numerical values must be within the range of 0-255.
Note
Timeout Behavior
Interrupted connections are not detected immediately when using the TCP/IP protocol. The
check-back message can take up to a minute.
Enabled Communication Methods with Modbus TCPIP
The following types of communication have been system-tested and approved:
● Point-to-point communication
● Multiple point connection of the WinCC station with an optional amount of controllers.
Note
Integrating the WinCC station via a bridge in a Modbus network is not possible because
the WinCC station works as a Modbus Master.
Online Configuration
The Online configuration is not supported.
4.3.2
How to configure a connection
Introduction
The following steps are required for configuring the channel "Modbus TCPIP":
1. Configuring a connection
2. Configuring Tags
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
71
Modbus TCPIP
4.3 Configuring the Channel
Requirements
● The communication driver for channel "Modbus TCPIP" is installed and integrated into the
project.
Procedure
1. Open the menu structure for the "Modbus TCPIP" communication driver in the "Tag
Management" editor of the WinCC Explorer.
2. Select the entry "New Connection" in the pop-up menu of the "Modbus TCP/IP Unit #1"
channel unit. The "Connection Properties" dialog is opened.
3. Enter the name of the connection.
4. Click on the "Properties" button to open the "Modbus TCPIP Properties" dialog.
5. Select the connected Modicon controller under "CPU Type". The following CPUs are
available for selection:
– 984
Use this CPU type for the CPU 984 (except for CPU 984A, 984B and 984X).
– Modicon Compact, Modicon Quantum, Modicon Momentum
– Modicon Premium, Modicon Micro
6. Enter the IP address of the controller in the "Server" field.
7. Enter the port to be used for the TCP/IP connection in the "Port" field. The default port for
Modbus TCP/IP connections is 502.
8. If you are using a bridge, enter the slave address of the remote controller in the "Address
of remote slave" field.
If no bridge is used, you must enter the default value of 255 or 0 as the address.
Note
Integrating the WinCC station via a bridge in a Modbus network is not possible because
the WinCC station works as a Modbus Master.
72
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Modbus TCPIP
4.3 Configuring the Channel
9. To swap the order of the 16-bit register in 32-bit process values, select "Swap words in 32bit values".
10.Close both of the dialogs by clicking the "OK" button.
4.3.3
Configuring the tags
4.3.3.1
Configuring the tags
Introduction
For a connection between WinCC and the automation system (AS) via channel "Modbus
TCPIP", tags of different data types can be created in WinCC.
The following sections describe how to configure the tags. The addressing of the data range
in the AS and the data type of the WinCC tags are different.
Tag Updating with the Modbus TCP/IP protocol
If the tags are retrieved simultaneously in a picture from a controller, the Modbus TCP/IP
channel attempts to optimize the update. This can only be accomplished under the following
conditions however:
● The tags are in the same address range.
● The tags are as close to one another as possible within the address range.
If you do not observe these recommendations, it can lead to noticeable differences in the
picture refresh with large amounts of tags. The acquisition cycles may not be maintained under
certain circumstances.
The best performance for the connection is achieved if you observe the following rules when
configuring the tags:
● Update of maximum 2000 tags simultaneously.
● Combine the tags in the least possible space, best in only one address range.
Data Types and Address Ranges in the Controller
The table lists the data types and address ranges that can be used when configuring tags and
structured tags.
Area with CPU
Premium/Micro
Area with CPU 984,
Compact, Quantum,
Momentum
data type
Coil
(discrete output)
%M
0x
Bit
Discrete input
(%I) – not realized by
Premium/Micro
1x
Bit
Name
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
1)
73
Modbus TCPIP
4.3 Configuring the Channel
Area with CPU
Premium/Micro
Area with CPU 984,
Compact, Quantum,
Momentum
Input register
(%IW) – not realized by
Premium/Micro
3x
Bit,
+/- Int, Int
Holding register
(output)
%MW
4x
Bit 2),
+/- Int, Int,
+/- Double, Double,
Float, ASCII
Extended memory
(Only available with the "Quantum/Momentum"
CPU)
--
6x
Bit 2),
+/- Int, Int,
+/- Double, Double,
Float, ASCII
Name
data type
1)
Due to a system characteristics of the external controller the last x bits on the end of the address area cannot be accessed.
2)
In the case of write accesses note:
With the "bit" data type in the "4x", "6x" and "%MW" areas, after changing the specified bit the entire word is written
back to the controller. There is no check to determine whether any other bits in the word have changed. As a result, the
controller only has read access to the specified word.
The standard bit counting method (16 LSB - 1 MSB) used with controllers of the 984, Compact,
Quantum and Momentum series will only be used for these CPUs in the "Tags" editor for the
data type "bit". Bit positions have the following allocations:
Left byte
Counting with tags
1
2
3
4
5
Right byte
6
7
8
9
10 11 12 13 14 15 16
When entering bit numbers in other locations in WinCC, the bit allocation of WinCC applies
(0 LSB - 15 MSB):
How the bit positions are
counted
Left byte
In the WinCC you configure: 15 14 13 12 11 10
Right byte
9
8
7
6
5
4
3
2
1
0
This bit counting method also applies to Modicon Premium and Modicon Micro controllers
Format for "Signed"
The placeholder "+/-" stands for the data types "Signed Int" and "Signed Double".
See also
How to Configure a Tag with Bit by Bit Access (Page 75)
How to Configure a Tag with Word by Word Access (Page 76)
How to Configure a Text Tag (Page 77)
74
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Modbus TCPIP
4.3 Configuring the Channel
4.3.3.2
How to Configure a Tag with Bit by Bit Access
Introduction
This section shows you how to configure a tag for bit by bit access for the address area in the
automation system (AS).
Requirements
● The channel "Modbus TCPIP" must be integrated in the project.
● A connection must be created in the "Modbus TCP/IP Unit #1" channel unit.
Procedure
1. Select "New Tag" from the shortcut menu of the Modbus TCP/IP connection. The "Tag
properties" dialog box opens.
2. Enter the name of the tag in the "Name" field. Select "Binary tag" in the "Data Type" field.
3. Click on the "Select" button to open the "Modbus TCP/IP Tag Properties" dialog. Define
the data area in the AS that holds the data in the "Area" field. You can select from areas
0x, 1x, 3x, 4x and 6x.
4. Enter the address of the tags in the respective address field, "4x" for instance. The value
depends on the configuration of the controller.
5. Enter the address of the bit in the "Bit" field if necessary. Whether an entry is possible
depends on your selection in the "Area from" field.
6. Select a value for "File" if you have set the value "6x Extended Memory" in the "Area" field.
7. Close both of the dialogs by clicking the "OK" button.
Note
After closing the "Modbus TCP/IP Tag Properties" dialog, the internal address of the tags
in the controller is shown in field "Address" of the "Tag Properties" dialog. This address
can differ from the entered address because it is adapted to the AS data format.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
75
Modbus TCPIP
4.3 Configuring the Channel
See also
How to Configure a Text Tag (Page 77)
4.3.3.3
How to Configure a Tag with Word by Word Access
Introduction
This section shows you how to configure a tag for word by word access for the address area
in the automation system (AS).
Requirements
● The channel "Modbus TCPIP" must be integrated in the project.
● A connection must be created in the "Modbus TCP/IP Unit #1" channel unit.
Procedure
1. Select "New Tag" from the shortcut menu of the Modbus TCP/IP connection. The "Tag
properties" dialog box opens.
2. Enter the name of the tag in the "Name" field. Set the data type to "Unsigned 16-bit value"
in the "Data Type" field.
3. Click on the "Select" button to open the "Modbus TCP/IP Tag Properties" dialog. Define
the data area in the AS that holds the data in the "Area" field. You can select from the three
areas 3x, 4x and 6x.
4. Enter the address of the tags in the respective address field, "4x" for instance. The value
depends on the configuration of the controller.
5. Close both of the dialogs by clicking the "OK" button.
Note
After closing the "Modbus TCP/IP Tag Properties" dialog, the internal address of the tags
in the controller is shown in field "Address" of the "Tag Properties" dialog. This address
can differ from the entered address because it is adapted to the AS data format.
76
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Modbus TCPIP
4.3 Configuring the Channel
4.3.3.4
How to Configure a Text Tag
Introduction
This section shows you how to configure a tag for word by word access for the address area
in the automation system (AS).
Requirements
● The channel "Modbus TCPIP" must be integrated in the project.
● A connection must be created in the "Modbus TCP/IP Unit #1" channel unit.
Procedure
1. Select "New Tag" from the shortcut menu of the Modbus TCP/IP connection. The "Tag
properties" dialog box opens.
2. Enter the name of the tag in the "Name" field. In the "Data Type" field, set "Text tag 8-bit
character set" as the data type.
3. Click on the "Select" button to open the "Modbus TCP/IP Tag Properties" dialog.
4. Enter the address of the tags in address field "4x". The value depends on the configuration
of the controller.
5. Close both of the dialogs by clicking the "OK" button.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
77
OPC Channel
5.1
5
WinCC OPC Channel
Introduction
WinCC can be used as both an OPC server and as an OPC client. The OPC channel is the
OPC client application of WinCC.
The OPC communication driver can be used as OPC DA client, OPC XML client, and OPC
UA client.
The following OPC components are installed automatically:
● OPC communication driver
● OPC Item Manager
Possible Applications
WinCC as an OPC DA client
If WinCC is used as an OPC DA client, the OPC channel must be added to the WinCC project.
A connection for data exchange is created in the WinCC project of the WinCC OPC DA client;
this is used to handle access to the WinCC tags of the OPC DA server.
To simplify the process, the OPC Item Manager is used. A WinCC OPC DA client can access
multiple OPC DA servers. This requires that a connection be created for each OPC server. In
this way, the WinCC OPC DA client can be used as a central operation and monitoring station.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
79
OPC Channel
5.1 WinCC OPC Channel
Note
The WinCC OPC channel establishes connections only to OPC servers which have the status
"OPC_STATUS_RUNNING".
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
80
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.2 OPC Item Manager
5.2
OPC Item Manager
Introduction
A connection and a WinCC tag are configured in the WinCC project of the WinCC OPC client
to enable access to tags of an OPC server. The OPC Item Manager simplifies this process for
you. The OPC Item Manager is automatically installed with WinCC.
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
Requirements
The following requirements must be met in order to use the OPC Item Manager for
configuration:
● The OPC server is an OPC DA server, an OPC XML server, or an OPC UA server
● A tag is already configured on the OPC server.
● If WinCC is to be used as the OPC server the WinCC project of the WinCC OPC server
must be enabled. If this is not the case, the OPC Item Manager cannot access the WinCC
OPC server.
● It must be possible to access the computer of the OPC servers via the IP address or HTTP.
● The OPC server must support the browser functionality. If that is not the case, access to
the tag of the OPC server must be configured manually.
Note
If you change language in the WinCC Explorer while the OPC Item Manager is open, no
tags are displayed when you click the "Browse Server" button. Exit the OPC Item Manager
before changing language.
Tasks of the OPC Item Manager
The OPC Item Manager assumes the following tasks:
● Select OPC server
● Creating a connection
● Tag selection
● Adding a tag
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
81
OPC Channel
5.2 OPC Item Manager
Selecting the OPC server
OPC DA server
The OPC Item Manager can be used to determine the name of the OPC DA server in the
network. These OPC DA servers can run on the same computer or on different computers in
the connected network environment. For further details, refer to "WinCC OPC DA client ".
OPC XML Server
The OPC Item Manager cannot be used to determine the name the OPC XML server. The
OPC XML server can be added using the "OPC Web Server" button. For further details, refer
to "WinCC OPC XML client ".
OPC UA Server
The OPC Item Manager cannot be used to determine the name the OPC UA server. The OPC
UA server can be added using the "OPC UA Server" button. For further details, refer to "WinCC
OPC UA client ".
Icons of the
OPC Item
Manager
Description
A networked computer has not yet been searched for installed OPC DA servers.
The computer was not found in the network or the computer could not be accessed.
A networked computer has been searched for installed OPC DA servers.
A networked computer contains the OPC DA server designated with the OPC symbol.
The number indicates which OPC DA specification of the WinCC OPC DA client is used.
\\<LOCAL>
82
Refers to the computer running the OPC Item Manager.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.2 OPC Item Manager
Icons of the
OPC Item
Manager
Description
Name of the OPC XML server.
http://
The OPC XML server can be added using the "OPC Web Server" button.
Name of the OPC UA server.
opc.tcp://
The OPC UA server can be added using the "OPC UA Server" button.
Creating a connection
The OPC Item Manager configures all required settings when creating a connection. If a
connection to the OPC server has already been created, this function is not available.
Tag selection
You may use the tag selection dialog to select one or more tags on the OPC server which the
WinCC OPC client is to access. Filter criteria can be used to limit the choices in the tag selection
dialog.
Adding a tag
The names of the WinCC tags that access the tags of the OPC server can be set in the "Add
Tags" dialog.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
83
OPC Channel
5.2 OPC Item Manager
The WinCC tag name consists of the "prefix", "name" and "suffix". The "Name" field is
preconfigured with the "ExampleTag" text. "ExampleTag" stands for the WinCC tag name of
the WinCC OPC server.
You can assign a prefix or suffix to distinguish the WinCC tag name on the WinCC OPC client
from the WinCC tag name on the WinCC OPC server. When configuring project monitoring, a
prefix or suffix must be assigned.
The tag name may be assigned only once in a given WinCC project.
Example
The WinCC tag name on the WinCC OPC DA server is called "OPC_Server_Tag". The "Client_"
value is entered in the prefix field and "_xyz" in the suffix field. In the WinCC project of the
WinCC OPC DA client, the WinCC tag "Client_OPC_Server_Tag_xyz" is created.
If the tag name on the OPC server contains special characters, they are replaced by an
underscore ( "_" ), because not all special characters occurring in tag names are supported
by the OPC Item Manager.
Click "Finish" to add the WinCC tags to the WinCC project of the WinCC OPC DA client. The
OPC Item Manager automatically sets the data type, the name and the address parameters
for the WinCC tag.
See also
How to Access a WinCC Tag with the OPC Item Manager (Page 103)
How to Access a WinCC Tag with the OPC Item Manager (Page 87)
84
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.3 Overview of the Supported WinCC Data Types
5.3
Overview of the Supported WinCC Data Types
The list below shows the data types that are supported by the WinCC OPC DA client and WinCC OPC
DA server:
● Binary tags
● Signed 8-bit value
● Unsigned 8-bit value
● Signed 16-bit value
● Unsigned 16-bit value
● Signed 32-bit value
● Unsigned 32-bit value
● Floating-point number 32-bit IEEE 754
● Floating-point number 64-bit IEEE 754
● Text tag, 8-bit character set
● Text tag, 16-bit character set
● Raw data type
● Structure types
● Text reference
Note
For structure types, only the structure elements are supported, not the structure itself.
However, the structure can be configured later. For more information, refer to the topic "Using
structures on the WinCC OPC DA client."
If a text tag is created with the OPC Item Manager, it is assigned a length of 160 characters.
This length can be changed to any length.
See also
How to Use Structures on the WinCC OPC DA Client (Page 94)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
85
OPC Channel
5.4 WinCC OPC DA Client
5.4
WinCC OPC DA Client
5.4.1
Functionality of the WinCC OPC DA Client
Introduction
The OPC channel does not require a separate communication module. The OPC channel is
an application which employs the OPC software interface to use an OPC DA server to access
process data.
If WinCC is to be used as an OPC DA client, the OPC channel must be added to the WinCC
project.
If a communication is established to a WinCC OPC DA server, the values of the WinCC tags
are exchanged. To do this, a connection is set up in the WinCC project of the WinCC OPC DA
client; it is used to handle access to the WinCC OPC DA server.
For the WinCC OPC DA client to access multiple OPC DA servers, a connection for each of
the OPC DA servers must be set up in the WinCC project. For more information about
troubleshooting channels and tags, refer to "Troubleshooting".
Note
The WinCC OPC channel establishes connections only to OPC servers which have the status
"OPC_STATUS_RUNNING".
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
Connection Monitoring
Three mechanisms are integrated for connection monitoring in the WinCC OPC-DA client. It
is thus possible to take the best possible measures in the event of a network error or
malfunction of an OPC DA server.
1. If the processing period for a DCOM activation exceeds warning value of 5 seconds, the
tag is assigned the value "Addressing Error". If the processing period exceeds the
cancellation value of 10 seconds, the connection to the OPC DA server is interrupted. This
is displayed in the "Connection Status" dialog of the WinCC Explorers.
The OPC DA specification 3.00 is provided with the "Keep-Alive" feature. If the OPC DA server
supports the OPC DA specifications 3.00, this feature is used. The feature causes the OPC
DA server to automatically trigger cyclic updating (call OnDataChange) even if the tag values
have not changed. If this regular updating is disabled, the WinCC OPC DA client terminates
the connection.
86
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.4 WinCC OPC DA Client
The same behavior applies in the case of an OPC DA server which supports the OPC DA
specifications 2.05a. In order to check the connection to the OPC DA server, the WinCC OPC
DA client requests the status cyclically every 10 seconds. If this regular updating is disabled,
the WinCC OPC DA client terminates the connection.
Generally, the WinCC OPC DA client terminates the connection to the OPC DA server when
the connection is not capable of functioning. The WinCC OPC DA client attempts to re-establish
the connection again, automatically, every 10 seconds.
See also
How to Use Structures on the WinCC OPC DA Client (Page 94)
Accessing a WinCC Tag without the OPC Item Manager (Page 92)
Configuring Access with the OPC Item Manager (Page 88)
Overview of the Supported WinCC Data Types (Page 85)
OPC Item Manager (Page 81)
Diagnosis of Channels and Tags (Page 369)
5.4.2
How to Access a WinCC Tag with the OPC Item Manager
5.4.2.1
How to Access a WinCC Tag with the OPC Item Manager
Introduction
When an OPC connection is made between WinCC and WinCC, data exchange occurs using
WinCC tags. The WinCC OPC DA client uses an OPC connection to read the WinCC tag
"OPC_Server_Tag" on the WinCC OPC DA server. To simplify the process, the OPC Item
Manager is used.
Requirements
● Two computers with WinCC projects.
● Both computers must be accessible via their IP addresses.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
87
OPC Channel
5.4 WinCC OPC DA Client
Configuration Steps
The following configurations are required in the WinCC project of the WinCC OPC DA client:
See also
Configuring Access with the OPC Item Manager (Page 88)
Configuring the OPC Channel on the WinCC OPC DA Client (Page 88)
Configuring Access with the OPC Item Manager (Page 103)
5.4.2.2
Configuring the OPC Channel on the WinCC OPC DA Client
Introduction
To use OPC for data exchange, the OPC channel must be set up in the WinCC project.
Procedure
1. Click the "Tag Management" icon in the navigation window of the WinCC Explorer on the
WinCC OPC DA client.
2. Select "Add New Driver" from the "Tag Management" shortcut menu. The "Add New Driver"
dialog is opened.
3. Select the "OPC.chn" driver and click the "Open" button. The channel is created and the
communication driver is displayed in the tag management.
See also
Configuring Access with the OPC Item Manager (Page 88)
5.4.2.3
Configuring Access with the OPC Item Manager
Introduction
This section explains how to use the OPC Item Manager to configure access to the WinCC
tag "OPC_Server_Tag" of the WinCC OPC DA server.
Requirements
● Configure an internal tag named "OPC_Server_Tag" of the data type "signed 16-bit value"
in the WinCC project of the WinCC OPC DA server.
● Enable the WinCC project of the WinCC OPC DA server.
● Add the "OPC" channel to the WinCC project of the WinCC OPC DA client.
88
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.4 WinCC OPC DA Client
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
Procedure
1. In the shortcut menu of the channel unit "OPC Groups(OPCHN Unit#1)" on the WinCC
OPC DA client, select "System Parameters". The "OPC Item Manager" opens.
2. Choose the name of the computer to be used as the WinCC OPC DA server from the
selection dialog.
Select "OPCServer.WinCC" from the list displayed.
3. Click the "Browse Server" button.
The "Filter criteria" dialog is opened.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
89
OPC Channel
5.4 WinCC OPC DA Client
4. Click "Next".
The "OPCServer.WinCC ..." dialog is opened.
5. Select the WinCC tag "OPC_Server_Tag".
Click the "Add Items" button.
6. If a connection to the WinCC OPC DA server already exists, continue with step 6.
If a connection has not been created, a message will be displayed.
Click on the "Yes" button. The "New Connection" dialog is opened.
90
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.4 WinCC OPC DA Client
7. Enter "OPCServer_WinCC" as the name of the connection. Click "OK".
The "Add Tags" dialog opens.
8. Enter the text "Client_" in the prefix field and the text "_xyz" in the suffix field.
9. Select connection "OPCServer_WinCC".
Click "Finish".
10.Click the "Back" button in the "OPCServer.WinCC ..." dialog.
Click "Exit" to close the OPC Item Manager.
See also
Configuring the OPC Channel on the WinCC OPC DA Client (Page 88)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
91
OPC Channel
5.4 WinCC OPC DA Client
5.4.3
Accessing a WinCC Tag without the OPC Item Manager
Introduction
OPC servers that do not support browser functionality require access to be configured
manually. Configuration of WinCC tags on the WinCC OPC DA client is shown using an
example of a WinCC-WinCC OPC connection.
Note
To access a WinCC tag without the OPC Item Manager, the ItemID must be set manually.
When addressing WinCC tags, the symbolic computer name (server prefix) can also be
specified. The ItemID has the following syntax: Server prefix::WinCC tag. If the WinCC tag
of the local WinCC project is addressed, the server prefix is omitted.
The following configurations are required in the WinCC project of the WinCC OPC DA client:
1. Selection of the "OPC_Var1" WinCC tag to be accessed.
2. Creation of a connection.
3. Configuration of the "Client_OPC_Var1_xyz" WinCC tag that accesses the WinCC tag of
the WinCC OPC DA server.
Requirements
● Two computers with WinCC projects.
● Both computers must be accessible via their IP addresses.
● Configure an internal tag named "OPC_Var1" with data type "signed 16-bit value" in the
WinCC project of the WinCC OPC DA server.
● Enable the WinCC project of the WinCC OPC DA server.
● Add the OPC channel to the WinCC project of the WinCC OPC DA client.
92
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.4 WinCC OPC DA Client
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
Procedure
1. Select "New Connection" from the shortcut menu of the channel unit "OPC Groups(OPCHN
Unit#1)" on the WinCC OPC DA client. The "Connection Properties" dialog is opened. Enter
a name for the connection in the corresponding field.
2. Click the "Properties" button. A dialog with the connection name in its title is displayed.
For connections to WinCC V 6, the entry in the "OPC Server Name" field must be
"OPCServer.WinCC".
3. Enter the name of the computer to be used as the OPC DA server in the "Start Server on
this Computer" field. Click "Test Server", to check the connection to the WinCC OPC DA
server.
4. Select "New Tag" from the shortcut menu of the connection. The "Tag Properties" dialog
opens.
5. Enter the name "Client_OPC_Var1_xyz" in the "Tag" field. Set the data type to "signed 16bit".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
93
OPC Channel
5.4 WinCC OPC DA Client
6. In the "Tag Properties" dialog, click the "Select" button. The "Address Properties" dialog
opens.
Enter the name of the WinCC tag of the WinCC OPC DA server in the "Item Name" field.
Leave the entry in the "Access Path" field unchanged. Set the data type to "signed 16-bit".
7. Click "OK" to close all open dialogs.
5.4.4
Using Structures on a WinCC OPC DA Client
5.4.4.1
How to Use Structures on the WinCC OPC DA Client
Introduction
Structures are used to organize tags and tag types that form a logical unit. This allows them
to be referenced using a single logical name.
Structures are not supported by the OPC DA specification. As a result, structures cannot be
set up using the OPC Item Manager, only the individual tags in a structure. If you wish to use
structures on the WinCC OPC DA client nonetheless, the data structure must be configured
subsequently in the WinCC project of the WinCC OPC DA client in order to supply it with the
relevant item names of the server tags.
Requirements
● Two computers with WinCC projects.
● Both computers must be accessible via their IP addresses.
Configuration steps
The following configuration steps are necessary to use structures on the WinCC OPC DA client:
● Configuring structures and structure tags on the WinCC OPC DA server
● Using structures on the WinCC OPC DA client in the WinCC project
94
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.4 WinCC OPC DA Client
See also
How to Configure Structures on the WinCC OPC DA Client (Page 96)
Configuring Structures and Structure Tags on the WinCC OPC DA Server (Page 95)
5.4.4.2
Configuring Structures and Structure Tags on the WinCC OPC DA Server
Introduction
In this section a structure and a structure tag is created in the WinCC project of the OPC DA
server. This configuration is required for the OPC DA client to access the structure tag.
Procedure
1. Select "New Structure Type" from the structure types shortcut menu on the WinCC OPC
DA server. The "Structure Properties" dialog is displayed.
2. Click "New Element" and create the internal tag "OPCServer_Struct" of data type SHORT.
Click "OK" to close the dialog.
3. In the navigation window, click the plus sign in front of the icon for tag management. Select
"New Tag" from the internal tag shortcut menu. Create a WinCC tag named "Var" with this
structure type.
4. The data frame of the WinCC Explorer shows the single tag "Var" and the structure tag
"Var.OPCServer_Struct".
5. Activate the WinCC project.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
95
OPC Channel
5.4 WinCC OPC DA Client
See also
How to Configure Structures on the WinCC OPC DA Client (Page 96)
5.4.4.3
How to Configure Structures on the WinCC OPC DA Client
Introduction
Structures are not supported by the OPC DA specification. As a result, structures cannot be
set up using the OPC Item Manager. In this section, the structure already present in the WinCC
project of the WinCC OPC DA server is configured for the WinCC project of the WinCC OPC
DA client. A WinCC tag that accesses the existing structure tag on the WinCC OPC DA server
is configured on the WinCC OPC DA client.
Requirements
● Create a structure and a structure tag named "Var.OPCServer_Struct" in the WinCC project
of the WinCC OPC DA server.
● Enable the WinCC project of the WinCC OPC DA server.
● Add the OPC channel to the WinCC project of the WinCC OPC DA client.
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
Procedure
1. Select "New Structure Type" from the structure types shortcut menu on the WinCC OPC
DA client. The "Structure Properties" dialog is displayed.
2. Click the "New Element" button and set up an external tag. Name the element exactly as
it is in the WinCC project of the OPC-DA server. Click "OK" to close the "Structure
Properties" dialog.
3. If a connection to the OPC DA server already exists, continue with step 6.
If no connection has been created, select "New Connection" from the shortcut menu of the
channel unit "OPC". The "Connection Properties" dialog is opened. Enter a name for the
connection in the corresponding field.
4. Click the "Properties" button. A dialog with the connection name in its title is displayed. For
connections to WinCC V 6, the entry in the field "OPC Server Name" must be
"OPCServer.WinCC".
5. Enter the name of the computer to be used as the WinCC OPC DA server in the field "Start
Server on this Computer". Click "Test Server", to check the connection to the WinCC OPC
DA server. Click "OK" to close the dialog.
96
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.4 WinCC OPC DA Client
6. Select "New Tag" from the shortcut menu of the connection. The "Tag Properties" dialog
opens. Select the newly created structure type as the data type.
7. In the "Tag Properties" dialog, click the "Select" button. The "Address properties" dialog
opens.
In the "Item Name" field, enter the name "Var.OPCServer_Struct" for the structure tag of
the WinCC OPC DA server. Leave the entry in the "Access Path" field unchanged.
8. Click "OK" to close all open dialogs.
See also
Configuring the OPC Channel on the WinCC OPC DA Client (Page 88)
Configuring Structures and Structure Tags on the WinCC OPC DA Server (Page 95)
5.4.5
Error Handling in the Event of Disturbed OPC DA Communication
5.4.5.1
Error Handling in the Event of Disturbed OPC Communication
Introduction
The procedure for communication testing is independent of how WinCC is used.
WinCC Used as the OPC DA Server
Use the channel diagnostics on the WinCC OPC DA client to determine whether a connection
to the OPC DA server can be established. For more information regarding channel problem
analysis, refer to "Troubleshooting".
WinCC Used as the OPC DA Client
Use the channel diagnostics on the WinCC OPC DA client to determine whether a connection
to the OPC DA server can be established. For more information regarding channel problem
analysis, refer to "Troubleshooting".
See also
WinCC is used as the OPC DA client, and the connection is not established. (Page 101)
WinCC is used as the OPC DA client, and the connection is established. (Page 100)
WinCC is used as the OPC DA server, and the connection is not established. (Page 99)
WinCC is used as the OPC DA server, and the connection is established successfully.
(Page 98)
Possibilities for Diagnosing the "OPC" Channel (Page 404)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
97
OPC Channel
5.4 WinCC OPC DA Client
5.4.5.2
WinCC as OPC DA Server
WinCC is used as the OPC DA server, and the connection is established successfully.
:LQ&&LVXVHGDVWKH23&'$VHUYHU
$FRQQHFWLRQLVHVWDEOLVKHGEXWWKH
YDOXHRIWKHWDJLVLQFRUUHFW
&KHFNWKHFRQILJXUDWLRQRIWKHLWHP
QDPHDQGWKHGDWDW\SHRIWKH23&
'$FOLHQW
$UHWKHLWHP
QDPHDQGGDWD
W\SHFRUUHFW"
1R
&RUUHFWWKHHQWULHV
<HV
,VWKH
$FFHVVSDWKILHOG
HPSW\"
<HV
'HOHWHWKHHQWU\
1R
$UHWKH
'&20VHWWLQJV
FRUUHFW"
1R
&KDQJHWKHFRQILJXUDWLRQRQWKH:LQ&&
'$23&VHUYHU
<RXFDQILQGIXUWKHULQIRUPDWLRQLQWKH
GRFXPHQWDWLRQRIWKHRSHUDWLQJV\VWHP
<HV
&RQWDFWWKH:LQ&&&XVWRPHU
6XSSRUW
&KHFNLIWKH
FRUUHFWYDOXHLVQRZ
GLVSOD\HG
<HV
<RXFDQQRZXVHWKH23&
FRQQHFWLRQIRUGDWD
FRPPXQLFDWLRQ
1R
&KHFNWKH23&'$FOLHQW
98
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.4 WinCC OPC DA Client
WinCC is used as the OPC DA server, and the connection is not established.
:LQ&&LVXVHGDVWKH23&'$VHUYHU
8QDEOHWRHVWDEOLVKDFRQQHFWLRQ
2SHQWKHUHJLVWUDWLRQHGLWRU,QWKH5HJLVWUDWLRQPHQXFOLFN
&RQQHFWZLWKQHWZRUNUHJLVWUDWLRQ(QWHUWKHQDPHRIWKH
FRPSXWHURQZKLFKWKH23&'$VHUYHULVUXQQLQJLQWKH
&RPSXWHUQDPHILHOG&OLFNWKH2.EXWWRQ
1R
,VWKH
FRPSXWHU
DYDLODEOHRQWKH
QHWZRUN"
&DQ\RXFRQQHFWWR
WKHQHWZRUNUHJLVWUDWLRQRIWKH
23&'$VHUYHU"
1R
<HV
<HV
,V5XQWLPH
DFWLYHRQWKH:LQ&&
23&'$VHUYHU"
0DNHVXUHWKH
FRPSXWHULVDYDLODEOH
RQWKHQHWZRUN
1R
$FWLYDWHWKH:LQ&&
SURMHFW
<HV
2SHQ7DVN0DQDJHU
RQWKH:LQ&&'$23&
VHUYHU,QWKH3URFHVVHVWDELV
WKH623&6(59:LQ&&SURFHVV
DFWLYH"
1R
$UHWKH
FRQILJXUHG3URJ,'
<HV
DQGWKHVHUYHUQDPHRIWKH
FOLHQWDSSOLFDWLRQ
FRUUHFW"
1R
<HV
&RUUHFWWKHHQWULHV
&KDQJHWKHFRQILJXUDWLRQRQWKH
:LQ&&'$23&VHUYHU
<RXFDQILQGIXUWKHULQIRUPDWLRQLQWKH
GRFXPHQWDWLRQRIWKHRSHUDWLQJV\VWHP
1R
$UHWKH
'&20VHWWLQJV
FRUUHFW"
<HV
&RQWDFWWKH:LQ&&&XVWRPHU
6XSSRUW
&KHFNLI\RXFDQ
HVWDEOLVKDFRPPXQLFDWLRQ
FRQQHFWLRQQRZ
<HV
<RXFDQQRZXVHWKH23&
FRQQHFWLRQIRUGDWDFRPPXQL
FDWLRQ
1R
&KHFNWKH23&'$FOLHQW
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
99
OPC Channel
5.4 WinCC OPC DA Client
5.4.5.3
WinCC as OPC DA Client
WinCC is used as the OPC DA client, and the connection is established.
:LQ&&LVXVHGDVWKH23&'$FOLHQW
$FRQQHFWLRQLVEHLQJHVWDEOLVKHGEXWWKHWDJYDOXHLV
LQFRUUHFW
,IWKH23&'$VHUYHU
KDVDEURZVHULQWHUIDFHDUH
WKHWDJVRIWKH23&'$VHUYHU
GLVSOD\HGLQWKH23&,WHP0DQDJHU"
<HV
1R
(QDEOHWKH:LQ&&SURMHFWRIWKH23&
'$FOLHQW6WDUWWKH:LQ&&&KDQQHO
'LDJQRVLVIURPWKH6WDUWPHQX(QDEOH
WKHWUDFHIXQFWLRQ
,QWKH:LQ&&SURMHFWRIWKH23&'$
FOLHQWRSHQWKHDGGUHVVSURSHUWLHVRI
WKH:LQ&&WDJWKDWDFFHVVHVWKHWDJRI
WKH23&'$VHUYHU
,QWKH$GGUHVV
3URSHUWLHVGLDORJDUHWKH
HQWULHVLQWKHILHOGV,WHP1DPHDQG
'DWD7\SHFRUUHFW"
1R
&RUUHFWWKHHQWULHV
<HV
$UHWKH
'&20VHWWLQJV
FRUUHFW"
&RQWDFWWKH:LQ&&&XVWRPHU
6XSSRUW
<HV
1R
&KDQJHWKHFRQILJXUDWLRQRQWKH
:LQ&&'$23&FOLHQW
)RUDGGLWLRQDOLQIRUPDWLRQUHIHUWRWKH
GRFXPHQWDWLRQRIWKHRSHUDWLQJ
V\VWHP
&KHFNZKHWKHU
\RXFDQHVWDEOLVKWKH
FRPPXQLFDWLRQFRQQHFWLRQ
QRZ
<HV
<RXFDQQRZXVHWKH23&
FRQQHFWLRQIRUGDWDWUDQVPLVVL
RQ
1R
&KHFNWKH23&'$
VHUYHU
100
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.4 WinCC OPC DA Client
WinCC is used as the OPC DA client, and the connection is not established.
:LQ&&LVXVHGDVWKH23&'$FOLHQW
8QDEOHWRHVWDEOLVKDFRQQHFWLRQ
*RWRWKH3URSHUWLHV&RQQHFWLRQ
GLDORJRQWKH23&'$FOLHQWDQG
FKHFNWKHHQWULHVLQWKH23&
&RQQHFWLRQWDE
,VWKH
FRPSXWHU
DYDLODEOHRQWKH
QHWZRUN"
1R
0DNHVXUHWKHFRPSXWHULV
DYDLODEOHRQWKHQHWZRUN
<HV
$UHWKH3URJ,'
DQGWKHFRPSXWHUQDPH
FRUUHFW"
<HV
1R
&RUUHFWWKHHQWULHV
$UHWKH
'&20VHWWLQJV
FRUUHFW"
<HV
&RQWDFWWKH:LQ&&&XVWRPHU
6XSSRUW
1R
&KDQJHWKHFRQILJXUDWLRQRQWKH
:LQ&&'$23&FOLHQW
<RXFDQILQGIXUWKHULQIRUPDWLRQLQWKH
GRFXPHQWDWLRQRIWKHRSHUDWLQJ
V\VWHP
&KHFNLIWKH
FRUUHFWYDOXHLVQRZ
GLVSOD\HG
<HV
<RXFDQQRZXVHWKH23&
FRQQHFWLRQIRUGDWDFRPPXQLFD
WLRQ
1R
&KHFNWKH23&'$
VHUYHU
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
101
OPC Channel
5.5 WinCC OPC XML Client
5.5
WinCC OPC XML Client
5.5.1
Functionality of the WinCC OPC XML Client
Introduction
The OPC channel does not require a separate communication module. The OPC
communication driver can be implemented as the OPC XML client.
In order to use WinCC as the WinCC OPC XML client, the OPC channel must be added to the
WinCC project.
The WinCC OPC XML client provides the OPC XML server with the OPC process data as a
web page. Access can be made to the web page via the Internet / Intranet using HTTP. When
a WinCC OPC XML client requests data, the web service is automatically started by the web
server.
In order that the WinCC OPC XML client can access several OPC XML servers, a connection
must be made to each OPC XML server in the WinCC project.
If a communication is established to a WinCC OPC XML server, the values of the WinCC tags
are exchanged. A connection is set up in the WinCC project of the WinCC OPC XML client via
which access to the WinCC OPC XML server can be processed. The connection monitoring
is not activated in the case of a WinCC OPC XML client.
Note
The WinCC OPC channel establishes connections only to OPC servers which have the status
"OPC_STATUS_RUNNING".
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
See also
Overview of the Supported WinCC Data Types (Page 85)
OPC Item Manager (Page 81)
102
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.5 WinCC OPC XML Client
5.5.2
How to Access a WinCC Tag with the OPC Item Manager
5.5.2.1
How to Access a WinCC Tag with the OPC Item Manager
Introduction
When an OPC connection is made between WinCC and WinCC, the data is exchanged by
means of WinCC tags. The WinCC OPC DA client uses an OPC connection to read the WinCC
tag "OPC_Server_Tag" on the WinCC OPC XML server. To simplify the process, the OPC
Item Manager is used.
Requirements
● Two computers with WinCC projects.
● It must be possible to access both computers using HTTP.
Configuration Steps
The following configurations are required in the WinCC project of the WinCC OPC XML client:
See also
Configuring the OPC Channel on the WinCC OPC DA Client (Page 88)
Configuring Access with the OPC Item Manager (Page 103)
5.5.2.2
Configuring Access with the OPC Item Manager
Introduction
This section explains how to use the OPC Item Manager to configure access to the
"OPC_XMLServer_Tag" WinCC tag of the WinCC OPC XML server.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
103
OPC Channel
5.5 WinCC OPC XML Client
Requirements
● Configure an internal tag named "OPC_XMLServer_Tag" of data type "signed 16-bit value"
in the WinCC project of the WinCC OPC XML server.
● Activate the WinCC project of the WinCC OPC XML server.
● The OPC channel must be added to the WinCC project of the WinCC OPC XML client.
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
104
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.5 WinCC OPC XML Client
Procedure
1. Select "System Parameters" from the shortcut menu of the channel unit "OPC
Groups(OPCHN Unit#1)" on the WinCC OPC XML client. The "OPC Item Manager" opens.
2. Click the "OPC Web Server" button. The "Add OPC Web Server" dialog is opened. Enter
the URL of the WinCC OPC XML server in the "URL" field in following format: <http://<xxx>/
WinCC-OPC-XML/DAWebservice.asmx>. Replace xxx with either the IP address or the
computer name on which the OPC XML web service is running.
Click "OK" to close the dialog.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
105
OPC Channel
5.5 WinCC OPC XML Client
3. A list appears from which to select "/WinCC-OPC-XML/DAWebservice.asmx>". Click the
"Browse Server" button. The "Filter criteria" dialog is opened.
4. Click the "Next->" button in the "Filter Criteria" dialog. The "http:// ..." dialog is opened.
5. In the "http:// ..." dialog, select the WinCC tag "XMLOPC_Server_Tag". Click the "Add Items"
button.
6. If a connection to the WinCC OPC XML server already exists, continue with step 7. If no
connection has been configured, a corresponding message is output.
Click "Yes". The "New Connection" dialog is opened.
Enter the name "OPCXMLServer_WinCC" for the connection. Click "OK".
106
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.5 WinCC OPC XML Client
7. The "Add Tags" dialog opens.
Enter the string "XMLClient_" in the prefix field, and "_xyz" in the suffix field. Select the
"OPCXMLServer_WinCC" connection. Click "Finish".
8. In the "http:// ..." dialog, click "<- Back". Click "Exit" to close the OPC Item Manager.
See also
Configuring the OPC Channel on the WinCC OPC DA Client (Page 88)
5.5.3
Accessing a WinCC Tag without the OPC Item Manager
Introduction
OPC servers that do not support browser functionality require access to be configured
manually. Configuration of WinCC tags on the WinCC OPC XML client is shown using an
example of a WinCC - WinCC OPC connection.
Note
To access a WinCC tag without the OPC Item Manager, the ItemID must be set manually.
When addressing WinCC tags, the symbolic computer name (server prefix) can also be
specified. The ItemID has the following syntax: server_prefix::<@>WinCC tag. If the WinCC
tag of the local WinCC project is addressed, the ItemID has the following syntax: <@>WinCC
tag.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
107
OPC Channel
5.5 WinCC OPC XML Client
Configuration Steps
The following configurations are required in the WinCC project of the WinCC OPC XML client:
1. Creation of a connection.
2. Configuring the "XMLClient_OPC_Var1_xyz" WinCC tag on the WinCC OPC XML client
which accesses the WinCC tag of the WinCC OPC DA server.
Requirements
● Two computers with WinCC projects.
● It must be possible to access the computers using HTTP.
● Configure an internal tag named "XMLOPC_Server_Tag" with data type "signed 16-bit
value" in the WinCC project of the WinCC OPC XML server.
● Enable the WinCC project of the WinCC OPC XML server.
● The OPC channel must be added to the WinCC project of the WinCC OPC XML client.
Note
When configuring external tags in the OPC channel, the preset values from WinCC in the
type conversion field of the "Tag Properties" dialog must not be altered. The data type of
the tag in the process is set in the data type field of the "Address Properties" dialog.
Procedure
1. Select "New Connection" from the shortcut menu of the channel unit "OPC Groups(OPCHN
Unit#1)" on the WinCC OPC XML client. The "Connection Properties" dialog is opened.
Enter a name for the connection in the corresponding field.
2. Click the "Properties" button. A dialog with the connection name in its title is displayed.
Select the "XML DA Server" check box. In the case of a connection to the WinCC OPC
XML server, the "OPC Server Name" field must contain the URL of the WinCC OPC XML
server. The URL has the following syntax: "http://<xxx>/WinCC-OPC-XML/
DAWebservice.asmx". Replace xxx with either the IP address or the computer name on
which the OPC-XML web service is running.
108
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.5 WinCC OPC XML Client
3. Select "New Tag" from the shortcut menu of the connection. The "Tag Properties" dialog
is opened.
4. Enter the name "XMLClient_OPC_Var1_xyz" in the "Tag" field. Set the data type to "signed
16-bit".
5. In the "Tag Properties" dialog, click the "Select" button. A dialog with the tag name in its
title is displayed.
Enter the symbol "<@>" and the name of the WinCC tag of the WinCC OPC XML server
in the "Item Name" field. Leave the entry in the "Access Path" field unchanged. Set the data
type to "signed 16-bit".
6. Click "OK" to close all open dialogs.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
109
OPC Channel
5.6 WinCC OPC UA client
5.6
WinCC OPC UA client
5.6.1
Functionality of the WinCC OPC UA client
Introduction
The WinCC OPC UA client enables data access to any OPC UA server in accordance with
the OPC Unified Architecture specification. OPC Unified Architecture (OPC UA) also provides
additional mechanisms such as authentication and encryption for secure communication
between participating partners.
To use WinCC as WinCC OPC UA client, add the OPC communication driver (OPC channel)
to the WinCC project. A separate communication module is not required.
To enable access to the OPC process data of different OPC UA servers, configure a connection
to each server in the WinCC project. Use the WinCC OPC Item Manager to configure the
connections.
Note
Connection monitoring is not activated if the OPC channel is used as OPC UA client.
Connections are only established to servers which signal the status "RUNNING".
5.6.2
Accessing a tag using the OPC Item Manager
5.6.2.1
Accessing an OPC tag using the OPC Item Manager
Introduction
If there is an OPC link from WinCC to an OPC UA server, OPC UA server data is mapped to
a WinCC tag. In this process, the WinCC OPC UA client uses a secure connection to access
the "OPC_UAServer_Tag" of the WinCC OPC UA server. Use OPC Item Manager for your
configuration.
Note
You can only access servers that offer browse support during the configuration.
Distinguish between client and server certificates when configuring. Secure communication
is only possible when client and server recognize each other's certificates.
Certificates are linked to the respective computers. After having moved, copied, or duplicated
the WinCC project to a different computer, repeat this procedure so that each computer can
verify the other's certificates.
110
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.6 WinCC OPC UA client
Requirements
● Client computers with a WinCC project.
● Both computers must be accessible via TCP connection.
● The Firewall allows two-way communication with the UA server.
Configuration Steps
Complete the following configuration tasks in the WinCC project of the WinCC OPC UA client:
● Configuration of the OPC channel on the WinCC OPC UA client.
● Setup of a valid server certificate.
● Configuration of access with the OPC Item Manager.
5.6.2.2
How to set up a server certificate
Introduction
This section explains how to set up an OPC UA server certificate for the WinCC OPC UA client.
Requirements
● The OPC UA server is activated.
● The Firewall allows two-way communication with the UA server.
● The "OPC" channel has been added to the WinCC project of the WinCC OPC UA client.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
111
OPC Channel
5.6 WinCC OPC UA client
Procedure
1. On the WinCC OPC UA client, select the "System parameters" command from the shortcut
menu of the "OPC Groups(OPCHN Unit#1)" channel unit. The "OPC Item Manager" opens.
2. Click "OPC UA server". The "Add OPC UA server" dialog opens. Enter the URL of the
WinCC OPC UA server in the "Server URL" field in the following format:
<opc.tcp://OPC UA server address>
Make the required security settings. If necessary, enter authentication data.
Close the dialog with "OK".
3. Select the "<opc.tcp://OPC UA server address>" entry from the list displayed.
4. Click "Browse Server".
An error dialog opens.
5. Close the error dialog.
112
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.6 WinCC OPC UA client
6. Open Windows Explorer and change to the "OPC" folder in the WinCC installation path.
7. Open the "PKI/CA/" folder.
The "rejected" folder containing the rejected server certificate has been added.
8. Move the server certificate from the "rejected" folder to the "certs" folder.
The server certificate has been validated. It is now possible to activate a secure connection
to the OPC UA server.
5.6.2.3
How to configure access to a tag using the OPC Item Manager
Introduction
This section explains how to use OPC Item Manager to configure access to the
"OPC_UAServer_Tag" WinCC tag of the WinCC OPC UA server.
Note
You can only access servers that offer browse support during the configuration.
Requirements
● The OPC UA server is activated.
● The Firewall allows two-way communication with the UA server.
● The server certificate has been set up.
● The "OPC" channel has been added to the WinCC project of the WinCC OPC UA client.
Note
"OPC" channel
Unicode is not supported for connection names. Make sure that you name all connections in
the project in the same language. Open the Control Panel of your computer to set the code
page of this language for use in programs that do not support Unicode.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
113
OPC Channel
5.6 WinCC OPC UA client
Procedure
1. On the WinCC OPC UA client, select "System parameters" from the shortcut menu of the
channel unit "OPC Groups(OPCHN Unit#1)". The "OPC Item Manager" opens.
2. Click "OPC UA server". The "Add OPC UA server" dialog opens. Enter the URL of the
WinCC OPC UA server in the "Server URL" field in the following format:
<opc.tcp://OPC UA server address>
Make the required security settings. If necessary, enter authentication data.
Click "OK" to close the dialog.
114
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.6 WinCC OPC UA client
3. Select the "<opc.tcp://OPC UA server address>" entry from the list displayed. Click "Browse
Server". The "Filter criteria" dialog is opened.
4. Click "Next". The "opc.tcp:// ..." dialog opens.
5. Select the tag to be mapped in the "opc.tcp:// ..." dialog, e.g. "OPC_UA_Server_Tag". Click
"Add items".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
115
OPC Channel
5.6 WinCC OPC UA client
6. Continue with step 7 if you have already set up a connection to the WinCC OPC UA server.
A message will be output if this connection is not available.
Click "Yes". The "New Connection" dialog is opened.
Enter the connection name "OPCUAServer". Click "OK".
7. The "Add Tags" dialog opens.
Enter the "UAClient_" string in the "Prefix" field and the "xyz" string in the "Suffix" field.
Select the "OPCUAServer" connection. Click "Finish".
8. Click "Back" in the "opc.tcp:// ..." dialog.
Click "Exit" in the "OPC Item Manager" dialog to close the OPC Item Manager.
116
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.6 WinCC OPC UA client
5.6.3
Error handling in event of disturbed communication
Introduction
The procedure for communication testing is independent of how WinCC is used.
WinCC used as OPC UA server
First, run the channel diagnostics on the WinCC OPC UA client to check whether it is possible
to set up a connection to the OPC UA server. For more information regarding channel problem
analysis, refer to "Troubleshooting".
WinCC used as OPC UA client
First, run the channel diagnostics on the WinCC OPC UA client to check whether it is possible
to set up a connection to the OPC UA server. For more information regarding channel problem
analysis, refer to "Troubleshooting".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
117
OPC Channel
5.6 WinCC OPC UA client
5.6.3.1
WinCC as OPC UA server
WinCC is used as OPC UA server, and the connection is set up.
:LQ&&LVXVHGDV23&8$VHUYHU$
FRQQHFWLRQLVEHLQJHVWDEOLVKHGEXW
WKHWDJYDOXHLVLQFRUUHFWRUWKH
VXEVFULSWLRQGRHVQRWSURYLGHDQ\
GDWD
&KHFNWKHFRQILJXUDWLRQRIWKHQRGH
,'DQGWKHGDWDW\SHVRIWKH23&8$
FOLHQW
$UHWKH
QRGH,'DQGWKH
GDWDW\SHFRUUHFW"
1R
&RUUHFWWKHHQWULHVLQWKH
23&8$FOLHQW
<HV
$UHWKH
'&20VHWWLQJV
FRUUHFW"
1R
<HV
&RQWDFWWKH:LQ&&&XVWRPHU
6XSSRUW
&KDQJHWKHFRQILJXUDWLRQRQWKH:LQ&&
8$23&VHUYHU
)RUDGGLWLRQDOLQIRUPDWLRQUHIHUWRWKH
GRFXPHQWDWLRQRIWKHRSHUDWLQJV\VWHP
7KH6,0$7,&+0,JURXSPXVWKDYH
VWDUWDQGDFFHVVSHUPLVVLRQWRWKH23&
8$VHUYHUDPRQJRWKHUWKLQJV
&KHFN
ZKHWKHUWKHFRUUHFW
YDOXHLVQRZGLVSOD\HG
<HV
<RXFDQQRZXVHWKH23&
FRQQHFWLRQIRUGDWD
WUDQVPLVVLRQ
1R
&KHFNWKH23&8$FOLHQW
118
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.6 WinCC OPC UA client
WinCC is used as the OPC UA server, and the connection is not set up.
:LQ&&LVXVHGDVWKH23&8$VHUYHU
8QDEOHWRHVWDEOLVKDFRQQHFWLRQ
2SHQWKHUHJLVWUDWLRQHGLWRU,QWKH5HJLVWUDWLRQPHQXFOLFN
&RQQHFWZLWKQHWZRUNUHJLVWUDWLRQ(QWHUWKHQDPHRIWKH
FRPSXWHURQZKLFKWKH23&8$VHUYHULVUXQQLQJLQWKH
&RPSXWHUQDPHILHOG&OLFNWKH2.EXWWRQ
1R
,VWKH
FRPSXWHU
DYDLODEOHRQWKH
QHWZRUN"
<HV
0DNHVXUHWKH
FRPSXWHULVDYDLODEOH
RQWKHQHWZRUN
1R
&DQ\RXFRQQHFWWR
WKHQHWZRUNUHJLVWUDWLRQRIWKH
23&8$VHUYHU"
<HV
,V:LQ&&LQ
5XQWLPHRQWKH23&
8$VHUYHU"
6WDUW:LQ&&5XQWLPHRQWKH
:LQ&&23&8$VHUYHU
1R
<HV
2SHQ6HUYLFHV
LQ&RPSXWHU0DQDJHPHQW
&KHFNLIWKH2SF8$6HUYHU
:LQ&&KDVVWDUWHGRULVUXQQLQJ
1R
,IWKHVHUYLFHRIWKH:LQ&&
23&8$VHUYHUKDVHQGHG
VWDUWWKHVHUYLFHPDQXDOO\
2WKHUZLVHFRQWDFW
:LQ&&&XVWRPHU6XSSRUW
<HV
$UHWKH
VHUYHUFOLHQW
FHUWLILFDWHVVHWXS
FRUUHFWO\"
1R
&RUUHFWWKHVHWWLQJ
<HV
&RQWDFWWKH:LQ&&&XVWRPHU
6XSSRUW
&KHFNLI\RXFDQ
HVWDEOLVKDFRPPXQLFDWLRQ
FRQQHFWLRQQRZ
<HV
<RXFDQQRZXVHWKH23&
FRQQHFWLRQIRUGDWDFRPPXQL
FDWLRQ
1R
&KHFNWKH23&8$FOLHQW
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
119
OPC Channel
5.6 WinCC OPC UA client
5.6.3.2
WinCC as OPC UA client
WinCC is used as the OPC UA client, and the connection is set up.
:LQ&&LVXVHGDVWKH23&8$FOLHQW
$FRQQHFWLRQLVHVWDEOLVKHGEXWWKHYDOXHRIWKHWDJLV
LQFRUUHFW
,IWKH23&8$VHUYHU
KDVDEURZVHULQWHUIDFHDUH
WKHWDJVRIWKH23&8$VHUYHU
GLVSOD\HGLQWKH23&,WHP0DQDJHU"
<HV
1R
$FWLYDWHWKH:LQ&&SURMHFWRIWKH23&
8$FOLHQW6WDUW:LQ&&&KDQQHO
'LDJQRVLVIURPWKH6WDUWPHQX
$FWLYDWHWKHWUDFHIXQFWLRQ
,QWKH:LQ&&SURMHFWRIWKH23&8$
FOLHQWRSHQWKHDGGUHVVSURSHUWLHVRI
WKH:LQ&&WDJVWKDWDFFHVVWKHWDJRI
WKH23&8$VHUYHU
,QWKH3URSHUWLHV
$GGUHVVGLDORJDUHWKH
HQWULHVLQWKH,WHPQDPHDQG'DWD
W\SHILHOGVFRUUHFW"
1R
&RUUHFWWKHHQWULHV
<HV
$UHWKH
'&20VHWWLQJV
FRUUHFW"
&RQWDFWWKH:LQ&&&XVWRPHU
6XSSRUW
<HV
1R
&KDQJHWKHFRQILJXUDWLRQRQWKH
:LQ&&8$23&FOLHQW
<RXFDQILQGIXUWKHULQIRUPDWLRQLQWKH
GRFXPHQWDWLRQRIWKHRSHUDWLQJ
V\VWHP
&KHFNLIWKH
FRUUHFWYDOXHLVQRZ
GLVSOD\HG
<HV
<RXFDQQRZXVHWKH23&
FRQQHFWLRQIRUGDWDFRPPXQL
FDWLRQ
1R
&KHFNWKH23&8$
VHUYHU
120
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
OPC Channel
5.6 WinCC OPC UA client
WinCC is used as OPC UA client, and the connection is not set up.
:LQ&&LVXVHGDVWKH23&8$FOLHQW
$FRQQHFWLRQLVQRWHVWDEOLVKHG
&KHFNWKHHQWULHVLQWKH
&RQQHFWLRQ3URSHUWLHVGLDORJRI
WKH23&&RQQHFWLRQWDERQWKH
23&8$FOLHQW
,VWKH
FRPSXWHU
DYDLODEOHLQWKH
QHWZRUN"
1R
0DNHVXUHWKDWWKHFRPSXWHULV
DYDLODEOHLQWKHQHWZRUN
<HV
$UHWKH23&
8$VHUYHUDGGUHVVDQG
WKHSRUWQXPEHUFRUUHFW"
<HV
&KHFNZKHWKHU
WKH23&8$VHUYHU
VXSSRUWVWKHVHFXULW\
VHWWLQJ
1R
<HV
&RUUHFWWKH
VHWWLQJV
1R
$UHWKHVHUYHU
DQGRUFOLHQW
FHUWLILFDWHVVHWXS
FRUUHFWO\"
&RUUHFWWKHHQWULHV
1R
<HV
$UHWKH
'&20VHWWLQJV
FRUUHFW"
<HV
&RQWDFWWKH:LQ&&&XVWRPHU
6XSSRUW
1R
&KDQJHWKHFRQILJXUDWLRQRQWKH
:LQ&&8$23&FOLHQW
)RUDGGLWLRQDOLQIRUPDWLRQUHIHUWRWKH
GRFXPHQWDWLRQRIWKHRSHUDWLQJ
V\VWHP
&KHFNZKHWKHU
<HV
\RXFDQHVWDEOLVKWKH
FRPPXQLFDWLRQFRQQHFWLRQ
QRZ
<RXFDQQRZXVHWKH23&
FRQQHFWLRQIRUGDWDWUDQVPLVVL
RQ
1R
&KHFNWKH23&8$
VHUYHU
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
121
PROFIBUS FMS
6.1
6
WinCC channel "PROFIBUS FMS"
Introduction
The "PROFIBUS FMS" communication driver makes the connection between a WinCC station
and automation systems such as S5 or S7.
This chapter describes
● how to configure data transfer with the "PROFIBUS FMS" channel
● how to configure a connection and a tag.
Channel Unit
The communication driver has a channel unit. This provides the following capability:
● Channel unit PROFIBUS FMS for SIMATIC NET PROFIBUS (communication module DP
5613).
Note
The configuration of the logical connection can take place in configuration mode as well
as in runtime. Both methods are explained.
Only WinCC can request data from the connected AS with the "PROFIBUS FMS" channel.
Sending from the AS is not possible.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
123
PROFIBUS FMS
6.2 Data type of the tags
6.2
Data type of the tags
Introduction
Define the required tags for a logical connection. From the WinCC viewpoint, you can access
the following data types:
● Binary tag
● Unsigned 8-bit value
● Signed 8-bit value
● Unsigned 16-bit value
● Signed 16-bit value
● Unsigned 32-bit value
● Signed 32-bit value
● Floating-point number 32-bit IEEE 754
● Text tag, 8-bit character set.
● Raw data type
124
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
PROFIBUS FMS
6.3 Configuring the Channel
6.3
Configuring the Channel
6.3.1
Configuring a connection
6.3.1.1
Configuring a connection
Introduction
The automation system must be connected to PROFIBUS with a suitable communication
processor. The PROFIBUS FMS protocol must be supported by the hardware / software.
In automation systems S5-115U, S5-135U and S5-155U, communication processor CP 5431
FMS is used for instance.
in WinCC system, the communication module CP 5613 and software SIMATIC NET must be
installed.
When configuring the connection, the following situations are handled differently:
● Configuring in configuration mode
● Configuring in Runtime
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
125
PROFIBUS FMS
6.3 Configuring the Channel
6.3.1.2
Configuring the connection in configuration mode
Procedure
1. Select the connection and open the "Connection properties" dialog window with menu point
"Properties" in the context menu.
2. Click the "Properties" button. A dialog with the connection name in its title is displayed.
3. Enter the name or the index of the logical connection in the "Name/Index" field.
The Name / Index of the logical connection must be configured in the local communication
relationship list (CRL).
4. If access authorization has been assigned for the logical connection, please select the "With
Authorization" field.
126
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
PROFIBUS FMS
6.3 Configuring the Channel
5. The "Attributes" button opens the "Access Authorization" dialog:
6. Now you can enter the password for the logical connection. Close the dialog by clicking on
the "OK" button.
7. Define the required parameter in the "Tag addressing" area. Close the dialog by clicking
on the "OK" button.
Note
To configure the Name or Index of the connection, you must access the communication
relationship list, which can be created with SIMATIC NCM PC or STEP 7.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
127
PROFIBUS FMS
6.3 Configuring the Channel
6.3.1.3
How to configure the connection in Runtime
Procedure
1. Select the connection and open the "Connection properties" dialog window with menu point
"Properties" in the context menu.
2. Click the "Properties" button. A dialog with the connection name in its title is displayed.
3. The configured connections from the communication relationship list (CRL) are shown in
the "List of connections (communication relationship list)" area. Select whether the
connection should be used with the respective index or name in the "Name/Index" field in
the "Connection" area.
4. If access authorization has been assigned for the logical connection, please select the "With
Authorization" field.
128
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
PROFIBUS FMS
6.3 Configuring the Channel
5. The "Attributes" button opens the "Access Authorization" dialog.
6. Now you can enter the password for the logical connection. Close the dialog by clicking on
the "OK" button.
7. Define the required parameter in the "Tag addressing" area. Close the dialog by clicking
on the "OK" button.
6.3.2
Configuring the tags
6.3.2.1
Configuring the tags
Introduction
The tag address is entered according to the address structure of the PROFIBUS FMS protocol.
When configuring addresses, a distinction is made between the following situations:
● in configuration mode
● in runtime
6.3.2.2
Configuring the address of the tags in configuration mode
Procedure
1. Select the tag and open the "Edit tag" dialog window with menu point "Properties" in the
context menu.
2. Select the desired data type for the tags (e.g. Signed 16 bit value) from the "General" tab.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
129
PROFIBUS FMS
6.3 Configuring the Channel
3. Click the "Select" button. A dialog with the tag name as its title is displayed.
4. Enter the name or index of the tag from the remote automation system in the "Name/Index"
field.
5. If the tag is a structured tag (structure or array), you must also enter - in the field "Subindex"
- which part of the tag (structure component or array element) should be read or written.
Note
The name or index and the Subindex must match the name or index in the Object List for the
logical connection of the external automation system. Otherwise it will not be possible to
access the tag in runtime.
6.3.2.3
How to configure the address of the tags in runtime
Procedure
1. Select the tag and open the "Edit tag" dialog window with menu point "Properties" in the
context menu.
2. Select the desired data type for the tags (e.g. Signed 16 bit value) from the "General" tab.
130
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
PROFIBUS FMS
6.3 Configuring the Channel
3. Click the "Select" button. A dialog with the tag name as its title is displayed.
4. The tags that can be accessed through the selected connection are listed in the "List of
Remote Tags" area. Select whether the tag should be chosen using its index or its name
in the "Remote tag" area.
5. In the "List of the Remote Tags", double click on the desired tag to select it.
6. The selected tag will be displayed in the "Name/Index" field in the "Remote Tag" area.
7. If the tag is a structured tag (structure or array), you must also enter - in the field "Subindex"
- which part of the tag (structure component or array element) should be read or written.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
131
7
S5 Ethernet Layer 4
7.1
WinCC Channel "SIMATIC S5 Ethernet Layer 4"
Introduction
The communication driver is used e.g. to connect automation systems SIMATIC S5-115U/H,
SIMATIC S5-135U and SIMATIC S5-155U/H with the ISO transport protocol or the TCP/IP
protocol.
Depending on the communication protocol that is used, the following communication partners
will be used.
Communication protocol
WinCC side
SIMATIC S5 side
ISO transport protocol
CP1612 (3Com-compatible)
CP1613
CP1623
CP1430 TF
TCP/IP (conforming with RFC1006)
CP1612 (3Com-compatible)
CP1613
CP1623
CP1430 TCP
When using this channel, no local database is required.
Channel units
The communication driver has two channel units "CP1413-x" which can operate a maximum
of two CP 1612, CP1613 or CP1623. The functionality of the channel unit is identical. They
differ only in the logical device names of the two CPs. CP1623 is identical to CP1613, but is
operated via PCI Express.
Communication can be established via the TCP/IP protocol with a CP1612, CP1613 or CP1623
using the third channel unit "TCP/IP".
The logical device name can be changed in the system parameters of a channel unit. Here, it
is also possible to set the parameters for the protocol used.
The following application capabilities exist:
● Channel unit "S5-Transport (CP 1413-1)" for the communication modules for SIMATIC
Industrial Ethernet (CP 1612/1613/1623).
● Channel unit "S5-Transport (CP 1413-2)" for the communication modules for SIMATIC
Industrial Ethernet (CP 1612/1613/1623).
● Channel unit "S5-Transport (TCP/IP)" for the communication modules for SIMATIC
Industrial Ethernet (CP 1612/1613/1623).
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
133
S5 Ethernet Layer 4
7.2 Data type of the tags
7.2
Data type of the tags
Introduction
Define the required tags for a logical connection. From the WinCC viewpoint, you can access
the following data types:
● Binary tag
● Unsigned 8-bit value
● Signed 8-bit value
● Unsigned 16-bit value
● Signed 16-bit value
● Unsigned 32-bit value
● Signed 32-bit value
● Floating-point number 32-bit IEEE 754
● Text tag, 8-bit character set
● Raw data type
134
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.3 Configuring the Channel
7.3
Configuring the Channel
7.3.1
Configuring the channel "SIMATIC S5 Ethernet Layer 4"
Introduction
The following steps are required for configuring the channel "SIMATIC S5 Ethernet Layer 4".
1. Configuring the connection
2. Configuring the tags
3. System parameter configuration
7.3.2
How to configure the connection
Introduction
The connection parameters are almost identical for all protocols used. In the following example,
communication is described using the ISO transport protocol with a channel unit "CP1413-x".
When implementing the TCP/IP protocol, the IP address of the AS is entered instead of the
Ethernet address. The IP address consists of four numerical values, separated by dots. The
numerical values must be within the range of 0-255.
For a logical connection, WinCC establishes one connection in the transport layer for reading
("READ function" area) and one for writing ("WRITE function" area). The address parameters
for both functions are defined in the dialog. Only if both connections are established is the
logical connection also indicated as being "established".
Allocations for the READ function
WinCC side
SIMATIC S5 side
FETCH Active
(Request "READ Active")
READ Passive
(Request "READ Passive")
FETCH Passive
(Request "WRITE Passive")
WRITE Active
(Request "WRITE Active")
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
135
S5 Ethernet Layer 4
7.3 Configuring the Channel
Note
It is not possible to write binary or byte variables in the data area of the AS, if the data from
the AS is sent active, i.e. the READ function is set to "FETCH Passive" in the connections
parameters.
A FETCH Passive connections is only assigned the "OK" status if at least one telegram has
been sent from AS to WinCC.
Allocations for the WRITE function
WinCC side
SIMATIC S5 side
Request "WRITE Active"
Request "WRITE Passive"
Procedure
1. Select the connection and open dialog window "Properties" with the context menu.
2. Actuate the "Properties" button on the "General" tab and open the "Connection Parameters"
dialog.
136
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.3 Configuring the Channel
3. Enter the station address of the SIMATIC S5 on the industrial Ethernet bus in the field
"Ethernet Address AG". When the TCP/IP protocol is being implemented, the IP address
is entered here in the IP address AG" field.
4. Define the parameters for the READ function in the WinCC system. These are independent
of the request used in the SIMATIC S5.
5. Then, enter the value in the allocated field "Own TSAP" that was configured in the "Remote
parameter" as "TSAP" while configuring the CP1430 TF.
6. Now, enter the value in the allocated field "Remote TSAP" that was configured in the "Local
parameter" as "TSAP" while configuring the CP1430 TF.
7. Define the parameters "Own TSAP" and "Remote TSAP" for the WRITE function
accordingly.
Note
In the entries for "TSAP", you must not use any spaces.
7.3.3
Configuring the tags
7.3.3.1
Configuring the tags
Introduction
For a connection between WinCC and the AS via channel "SIMATIC S5 Ethernet Layer 4",
tags of different data types can be created in WinCC. The following describes how to configure
a tag of these data types.
● Addresses of tags
● Configuring a tag with bit by bit access
● Configuring a tag with byte by byte access
● Configuring a tag with word by word access
● Configuring a raw data tag
7.3.3.2
Addresses of tags
Introduction
The tag address is entered according to the address structure of the SIMATIC S5.
Depending on the tag type, the access to memory areas in the AS is bit by bit, byte by byte or
word by word. For this purpose, the addressed memory area is read from the AS for every
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
137
S5 Ethernet Layer 4
7.3 Configuring the Channel
single write request and the corresponding bits and/or bytes are modified. Afterwards, the data
is written back to the AS's memory.
Note
Changes that have been made by the AS in a read data area are overwritten when writing
back into the data area.
It is not possible to write binary or byte variables in the data area of the AS, if the data from
the AS is sent active, i.e. the READ function is set to "FETCH Passive" in the connections
parameters.
Configuring the address of a tag is done independent of the tag type:
● With tags of type "binary" or 8 bit value", first the "Bits-/Bytes-tag" dialog is opened, in which
the bitwise or byte-wise access to the memory area of the AS is defined.
Afterwards, the address of the tag in the AS memory is defined in the "Address properties"
dialog.
● For word-oriented tags, the address of the tag in the AS memory is defined in the "Address
properties" dialog.
The dialog "Bits-/Bytes-tag" is not opened, since the access to the AS memory is word by
word.
7.3.3.3
How to Configure a Tag with Bit by Bit Access
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "binary tag" on the "General" tab.
138
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.3 Configuring the Channel
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
4. Use the checkbox to define whether access should be enabled for reading and writing
certain bits in the memory area.
5. Select the addressing methods for the AS memory in the selection field e.g. "Word" or "Byte".
6. Select the number of bits to be changed in the selection field.
7. Use the "Selection" button to open the "Address properties" dialog for defining the tag
address in AS.
Note
With the S5, flags, inputs and outputs can be addressed by byte, data blocks (DB, DX) are
addressed by word.
Activating the checkbox "Access a bit" affects the display of the fields of the "Address
properties" dialog.
For word-oriented tags, the described "Bit-/Byte-tag" is not opened because the address of
the tags and therefore the access to PLC memory is by word.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
139
S5 Ethernet Layer 4
7.3 Configuring the Channel
7.3.3.4
How to Configure a Tag with Byte by Byte Access
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "Unsigned 8 bit value" or "Signed 8 bit value" in the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
4. Use the checkbox to define whether access should be enabled for reading and writing
certain bytes in the memory area.
5. Only "Word" is shown as the AS memory addressing type in the selection field.
6. Select the number of bytes to be changed in the selection field.
7. Use the "Selection" button to open the "Address properties" dialog for defining the tag
address in AS.
140
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.3 Configuring the Channel
Note
With the S5, flags, inputs and outputs can be addressed by byte, data blocks (DB, DX) are
addressed by word.
Activating the checkbox "Access a byte" affects the display of the fields of the "Address
properties" dialog.
For word-oriented tags, the described "Bit-/Byte-tag" is not opened because the address of
the tags and therefore the access to PLC memory is by word.
7.3.3.5
How to Configure a Tag with Word by Word Access
Introduction
The addresses of tags in AS are defined with the dialog that is described here.
● With tags of type "binary" or 8 bit value", first the "Bits-/Bytes-tag" dialog is opened, in which
the bitwise or byte-wise access to the memory area of the AS is defined.
● For word-oriented tags, the "Bit-/Byte-tag" dialog is not opened because the address of the
tags and therefore the access to AS memory is by word.
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select the desired data type for the tags (e.g. Signed 16 bit value) from the "General" tab.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
141
S5 Ethernet Layer 4
7.3 Configuring the Channel
3. Click the "Select" button. The "Address properties" dialog is opened.
4. Choose whether the tag is located in a data block, the flag area, an input area or an output
area in the "Data Area" field of the "Address" tab.
5. If the tag is in a data block, the "DB No." field is also shown. Here, you enter the number
of the data block.
6. The type of addressing is entered in the "Addressing" field. Normally, you can use the
default definition.
7. Enter the address in the respective field (e.g. "DW ").
Note
For tags of type "binary" or "8 bit value", displaying the fields of this dialog depends on the
selection made for "Access to bits/bytes" in the "Bits-/Bytes-tag" dialog.
If the tag of a word-oriented data area is to be written, the start address must be in the left
byte and the length of the tags must be an even number.
142
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.3 Configuring the Channel
7.3.3.6
How to configure a raw data tag
Introduction
The following is a description of how the address of a raw data tag is defined.
Note
If the tag of a word-oriented data area is to be written, the start address must be in the left
byte and the length of the tags must be an even number.
Procedure
1. Select the tag and open dialog window "`Tag properties" with the "Properties" context menu.
2. Select the entry "Raw data type" on the "General" tab.
3. Click the "Select" button to open the "Address properties" dialog.
4. Choose whether the tag is located in a data block, a flag, an input area or an output area
in the "Data Area" field.
5. If the tag is in a data block, the "DB No." field is also shown. Here, you enter the number
of the data block.
6. The type of addressing is entered in the "Addressing" field. Normally, the default definition
can be used.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
143
S5 Ethernet Layer 4
7.3 Configuring the Channel
7. Enter the data address in the field underneath. The label on the field depends on the entry
in the "Addressing" field, e.g. "DBW" for Word addressing.
8. Enter the length of the raw data block in bytes in the Length field.
9. Define which type of raw data tag is concerned in the "Raw data type" area.
7.3.4
System parameters
7.3.4.1
System parameters of the channel unit
Introduction
If you require a configuration that deviates from the standard WinCC settings, you can make
all the required changes using the "System Parameter" dialog of the channel unit.
The system parameters are almost identical for all protocols used. When implementing the
TCP/IP protocol, only the device name given during the installation is different.
The following individual points can be changed:
● the device name
● the transport parameter
Note
The system parameters apply for all CPs in the AS.
Device Name
Communication between WinCC and the automation system takes place via logical device
names. These names are assigned during the installation of the communication module and
are unit-specific. The device name represents the logical device name. The logical device
name is given the name "/CP_H1_1:/ SCP" with the ISO transport protocol and "/TCP_IP:/SCP"
with the TCP/IP protocol as a default definition.
Note
When using the TCP/IP protocol, you must check whether the device name in WinCC
matches the "Access point of the application" in the "Set PG/PC interface" dialog. The device
name must also be changed in "Set PG/PC interface".
Transport Parameter
Specific settings for the channel unit are made in the transport parameters, e.g. PDU size,
setup attempts, etc.
144
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.3 Configuring the Channel
7.3.4.2
How to Change the Device Name
Introduction
Parameters of the channel unit are set with the system parameters, e.g. the logical device
name or the transport parameters.
The system parameters are almost identical for all protocols used.
In the following example, communication is described using the ISO transport protocol with a
channel unit "CP1413-x".
When implementing the TCP/IP protocol, only the device name given during the installation is
different.
Procedure
1. Select the channel unit and open dialog window "System parameters" with the context
menu.
2. Select the "Device Name" Tab.
3. Now, you can select the device name shown in bold print with the mouse and change it
with a mouse click in the name field for the device name.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
145
S5 Ethernet Layer 4
7.3 Configuring the Channel
Note
The device name is defined during the installation of the hardware driver. Only if you have
defined another name there, which is not recommended, will you have to change the device
name here as well.
7.3.4.3
How to change the transport parameter
Procedure
1. Select the channel unit and open dialog window "System parameters" with the context
menu.
2. Select the "Transport parameter" tab.
3. Set the value for "PDU size" to the value that was configured on the communication module
CP 1430.
4. Define how often a connection establishment should be attempted in the "Setup attempt"
filed.
146
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.3 Configuring the Channel
5. Select "Infinite" in the "Duration of Send Repetitions" area.
6. Enter value e.g. 30 in the "Acknowledgement time" field so that you are informed of the tag
status after 30 seconds at the most, if the communication partner has not responded within
this time (e.g. AS in "Stop" status).
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
147
S5 Ethernet Layer 4
7.4 Appendix
7.4
Appendix
7.4.1
Appendix
Introduction
Added information on the channel "SIMATIC S5 Ethernet Layer 4" is provided in the appendix.
7.4.2
Internal error codes and constants
7.4.2.1
Internal error codes and constants
Introduction
The following tables contain the most important error codes and constants. The information is
intended for "insiders". Therefore, we have not gone into more detail on the meanings of the
codes and constants.
● Error codes during connection disturbances
● iNA960 messages
● SCI messages
7.4.2.2
Error codes during connection disturbances
Introduction
The most important error codes are listed in this section. If an error with an error code that is
not in the table occurs, please call the WinCC hotline.
Fehler_0002-INVALID_RQ
Faulty request block.
Fehler_0004-NO_RESOURCES
No resources free in CP.
Fehler_0006-UNKNOWN_REFERENCE
Incorrect OPEN reference defined.
148
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.4 Appendix
Fehler_0008-BUFFER_TOO_SHORT
User buffer too short.
Fehler_0010-BUFFER_TOO_LONG
User buffer too long.
Fehler_0012-ILLEGAL_REQ
Incorrect "negot_options" defined.
Fehler_0014-REM_ABORT
Connection aborted by remote station.
Fehler_0016-LOC_TIMEOUT
Timeout.
Fehler_0018-UNKNOWN_CONN_CLASS
Unknown connection class.
Fehler_0020-DUP_REQ
Connection already established.
Fehler_0022-CONN_REJECT
Connection request rejected by remote.
Fehler_0024-NEGOT_FAILED
Connection abort faulty "negot-option".
Fehler_0026-ILLEGAL_ADDRESS
Faulty transport address.
Fehler_0028-NETWORK_ERROR
Bus or CP disrupted.
Fehler_0030-PROTOCOL_ERR
Protocol error.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
149
S5 Ethernet Layer 4
7.4 Appendix
Fehler_0032-ILLEGAL_RB_LENGTH
Incorrect request block length.
Fehler_0784-E_NO_HW
No communication hardware found.
● Communication module defective.
● Communication module not installed correctly.
● Wrong port address defined.
Fehler_0786-E_CNF
Driver configured incorrectly or invalid parameter in the registry.
Fehler_0787-E_BAUDRATE
Incorrect baudrate or incorrect interrupt vector defined.
Fehler_0788-E_HSA
Incorrect HSA (Highest Station Address) defined.
Fehler_0789-E_TS
The defined local participant number (TS_ADR) is already assigned.
Fehler_0791-E_INT_NOT_PROV
The defined interrupt vector (IRQ) is not available on the communication module.
Fehler_0792-E_INT_BUSY
The defined interrupt vector (IRQ) is already occupied on the communication module.
Fehler_0800-E_NO_FILE
The selected communication driver cannot be loaded; the file was not found.
● Communication driver not installed correctly.
Fehler_0897-E_LOGDEV
The logical device is not defined in the registry.
● Communication driver not installed correctly.
● Entry damaged or deleted in the registry.
150
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.4 Appendix
● Check the setting of the logical device name with the "Set PG/PC interface" program.
● Check the setting for the logical device name in the "System parameter - Device" mask.
Fehler_0898-E_L2DRIVER
The entry "L2DRIVER" is missing in the registry.
● Module error or module installed incorrectly.
Fehler_0900-E_L4DRIVER
The entry "L4DRIVER" is missing in the registry.
● Module error or module installed incorrectly.
Fehler_30000-EC_WATCHDOG
Watchdog error.
Fehler_30001-EC_PDUERROR
PDU not expected.
Fehler_30005-EC_ONLERROR
Fault loading the S7-Online-DLL.
7.4.2.3
iNA960 messages
General iNA960 messages
OK_RESP
1
0x01
Request executed with no errors
OK_EOM_RESP
3
0x03
Data block received with no errors
OK_DECIDE_REQ_RESP
5
0x05
Request executed with no errors
OK_CLOSED_RESP
7
0x07
Connection aborted by local user
iNA960 error messages
INVALID_REQ
2
0x02
Faulty request block
NO_RESOURCES
4
0x04
No resources free in CP
UNKNOWN_REFERENCE
6
0x06
Incorrect OPEN reference defined
BUFFER_TOO_SHORT
8
0x08
User buffer too short
BUFFER_TOO_LONG
10
0x0A
User buffer too long
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
151
S5 Ethernet Layer 4
7.4 Appendix
7.4.2.4
ILLEGAL_REQ
12
0x0C
Incorrect "negot_options" defined
REM_ABORT
14
0x0E
Connection aborted by remote station
LOC_TIMEOUT
16
0x10
Timeout
UNKNOWN_CONN_CLASS
18
0x12
Unknown connection class
DUP_REQ
20
0x14
Connection already established
CONN_REJECT
22
0x16
Connection request rejected by remote
NEGOT_FAILED
24
0x18
Connection abort faulty negot-option
ILLEGAL_ADDRESS
26
0x1A
Faulty transport address
NETWORK_ERROR
28
0x1C
Bus or CP disrupted
PROTOCOL_ERR
30
0x1E
Protocol error
ILLEGAL_RB_LENGTH
32
0x20
Incorrect request block length
SCI messages
See description in the "SINEC Communication Interface SCI" manual (A/5-15).
SCI messages
152
SCP_OK
0
0x00
No error
SCP_INCONS
201
0xC9
Minor device number is not 00
SCP_RESOURCE
202
0xCA
DPRAM request invalid
SCP_CONFIG
203
0xCB
Configuration error (NUM_PROCS)
SCP_NOCONFIG
204
0xCC
SCP driver not configured
SCP_PARAM
206
0xCE
Incorrect mode
SCP_DEVOPEN
207
0xCF
Open already performed
SCP_BOARD
208
0xD0
Board not inserted/recognized
SCP_SOFTWARE
209
0xD1
IRQ error or software not found
SCP_MEM
210
0xD2
Low memory in DPRAM
SCP_MODE
211
0xD3
Download process not yet ended
SCP_LOADER
212
0xD4
No response from loader
SCP_SIGNAL
213
0xD5
Process started asynchronously
SCP_NOMESS
215
0xD7
No message arrived for the process
SCP_USERMEM
216
0xD8
length_of_buffer too small
SCP_WINDOW
217
0xD9
Too many SEND calls
SCP_TIMEOUT
219
0xDB
Timeout on SCP
SCP_ATTACH
220
0xDC
Reset not executed/Channel still active
SCP_ILLEGAL_REQUEST
221
0xDD
Illegal request
SCP_ERECOVERF
223
0xDF
Buffer not retrieved with scp_receive
SCP_ECLOSED
224
0xE0
All buffers assigned for the connection
EUSERMAX
225
0xE1
SCP_EINTR
226
0xE2
SCP_BOARD_OPEN
231
0xE7
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Ethernet Layer 4
7.4 Appendix
SCP_NO_WIN_SERV
233
0xE9
EPROTECT
234
0xEA
License not found
SCI messages
SCP_DB_FILE_DOES_NOT_EXIST
240
0xF0
SCP_DB_FILE_CLOSE_NOT_OK
241
0xF1
SCP_SEND_NOT_SUCCESSFUL
242
0xF2
SCP_RECEIVE_NOT_SUCCESSFUL
243
0xF3
SCP_NO_DEVICE_AVAILABLE
244
0xF4
SCP_ILLEGAL_SUBSYSTEM
245
0xF5
SCP_ILLEGAL_OPCODE
246
0xF6
SCP_BUFFER_TOO_SHORT
247
0xF7
SCP_BUFFER_1_TOO_SHORT
248
0xF8
SCP_ILLEGAL_PROTOCOL_SEQUENCE
249
0xF9
SCP_ILLEGAL_PDU_ARRIVED
250
0xFA
SCP_REQUEST_ERROR
251
0xFB
SCP_NO_LICENSE
252
0xFC
Additional online DLL messages on the SCP interface
E_TIMER_INIT
768
0x0300
WIN Set-timer request unsuccessful
E_INIT_COM
769
0x0301
E_NO_HW
784
0x0310
MPI module not found
E_HW_DEFEKT
785
0x0311
Problem with the hardware
E_CNF
786
0x0312
Incorrect configuration parameter
E_BAUDRATE
787
0x0313
Incorrect baudrate/incorrect IntVector
E_HSA
788
0x0314
Incorrect HSA configured
E_TS
789
0x0315
Configured address already assigned
E_OCC
790
0x0316
HW_Device already assigned
E_INT_NOT_PROV
791
0x0317
Interrupt not available
E_INT_BUSY
792
0x0318
Interrupt occupied
E_SAP
793
0x0319
SAP deactivate: SAP not occupied
E_UNPLUGGED
794
0x031a
No remote station found
E_SYNI
795
0x031b
Syni Error occurred
E_AMPRO
796
0x031c
AMPRO 2 reported a system error
E_BUFFSIZE
797
0x031d
No buffer of this size created
E_NO_FILE
800
0x0320
DLL/VxD File not found or entries in registry destroyed
E_NO_ENTRY
801
0x0321
Address does not exist in DLL
E_VERSION
816
0x0330
Version conflict between SMC driver and SMC firmware
E_COMCNF
817
0x0331
Problem with the COM port configuration
E_NO_SMC
818
0x0332
SMC no longer responds
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
153
S5 Ethernet Layer 4
7.4 Appendix
E_COMMBADID
819
0x0333
COM port is not configured
E_COMMOPEN
820
0x0334
COM port is not available
E_SMCBUSY
821
0x0335
Serial driver is currently in use with another
configuration
E_SMCMODEM
822
0x0336
No connection exists to a PC/MPI cable
E_SMCNOLEG
823
0x0337
PC/MPI cable rejects request, necessary authorization
is missing
E_ONLINE
896
0x0380
Internal error at the IOCTL interface
E_LOGDEV
897
0x0381
Logical device not in registry
E_L2DRIVER
898
0x0382
L2DRIVER entry is missing in the registry
E_L4DRIVER
900
0x0384
L4DRIVER entry is missing in the registry
E_SYSERROR
1023
0x03FF
System error
Channel-specific error codes
154
EC_WATCHDOG
30000
0x7530
Watchdog error
EC_PDUERROR
30001
0x7531
PDU not expected
EC_ONLERROR
30005
0x7535
Fault loading the S7-Online-DLL
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.1
8
WinCC channel "SIMATIC S5 Profibus FDL"
Introduction
The channel "SIMATIC S5 Profibus FDL" is used for communication between WinCC Station
and a SIMATIC S5 automation system. The PROFIBUS (Process Field Bus) network type and
protocol FDL (Field Data Link) are used in this case.
PROFIBUS is the network for small to medium sized data quantities. A broad spectrum of
automation tasks can be completed with a maximum of 127 possible participants.
Reading/writing tags via PROFIBUS, using the FDL protocol, is done using request and
response telegrams. The request telegram is sent to the automation device from WinCC. The
AS answers with the response telegram.
An FDL connection is specified with the local and remote connection end point (Service Access
Point).
This chapter describes
● how to configure the data transfer with the "SIMATIC S5 Profibus FDL" channel.
● how to create a sample project
Channel unit FDL (CP5412/A2-1)
Independent of the communication processor used, CP 5613 or CP 5614, connection can be
made to the SIMATIC S5 via the channel unit "FDL (CP5412/A2-1)". This channel unit supports
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
155
S5 PROFIBUS FDL
8.1 WinCC channel "SIMATIC S5 Profibus FDL"
up to a maximum of 24 connections. In order for the channel to function, a channel unit and a
connection must be set up.
Service Access Point
SAPs are local data interfaces within a PROFIBUS node. The SAPs must be configured in
WinCC and on the AS. A unique identification is defined with the Service Access Point. This
unique identification is required for communication between the WinCC and the AS.
Active connection
An active connection is also called a Fetch connection. This is a connection, with which an
active partner retrieves data with a communication partner. The communication partner that
the data is retrieved from is designated as a passive partner.
Passive connection
A passive connection exists if the active AS sends data to the passive WinCC partner
asynchronously without a request telegram.
156
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.2 Supported data types and data ranges
8.2
Supported data types and data ranges
Introduction
Only certain data types and data ranges are supported for communication from SIMATIC S5
via PROFIBUS FDL.
Supported data types
WinCC Data type
SIMATIC S5 data type
Binary tag
BIT
Signed 8-bit value
non-existent in the SIMATIC S5
Unsigned 8-bit value
BYTE
Signed 16-bit value
WORD
Unsigned 16-bit value
WORD
Signed 32-bit value
DWORD
Unsigned 32-bit value
DWORD
Floating-point number 32-bit IEEE 754
DWORD
Floating-point number 64-bit IEEE 754
non-existent in the SIMATIC S5
Text tag, 8-bit character set
ARRAY OF BYTE
Text tag, 16-bit character set
non-existent in the SIMATIC S5
Raw data type
ARRAY OF BYTE
Access to SIMATIC S5 tags
The access to SIMATIC S5 tags is done word by word to data block DB or extended data
blocks DX. This allows read and write access.
Access to a SIMATIC S5 tag of data type BIT
SIMATIC S5 tags of data type BIT only allow read access. This restriction applies for active or
passive connections.
Access to a SIMATIC S5 tag of data type BYTE
SIMATIC S5 tags of data type BYTE only allow read access.
To configure a byte tag, the "left byte" or "right byte" of a 16 bit data word must be selected
for addressing.
Access to a SIMATIC S5 tag of data type ARRAY OF BYTE
SIMATIC S5 tags of data type ARRAY OF BYTE only allow read access.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
157
S5 PROFIBUS FDL
8.3 Features of the WinCC channel "SIMATIC S5 Profibus FDL"
8.3
Features of the WinCC channel "SIMATIC S5 Profibus FDL"
Introduction
The capabilities of communication, from WinCC via the communication driver for PROFIBUS,
are listed in the following section. All supported data types and the respective capabilities for
format adaptation are also listed.
Note
Features for writing tags:
When configuring in WinCC, make sure that every tag is transferred individually when writing
more than one tag into data areas of the automation system.
This behavior is especially important when writing more than one tag to a script with function
"SetTagMultiWait". Since this function is only executed at the end of a transfer of all the tags
sent to it, noticeable waiting times can occur with a greater number of tags.
Check for whether the utilization of the "Wait" function is required for a larger amount of tags.
In this case, the use of a raw data tag may also be a good idea, especially if the data is
sequential in the AS data area.
Type conversion
A format adaptation is then required if a certain value range or a conversion e.g. of decimal to
BCD ("Unsigned 8 bit value" converted to "ByteToBCDWord") if necessary. No format
adaptation is performed as standard procedure.
The following table lists the supported WinCC data types and the respective format adaptation
capabilities.
158
WinCC Data type
Type conversion
Binary tag
No
Signed 8-bit value
non-existent in the S5
Unsigned 8-bit value
Yes
Signed 16-bit value
Yes
Unsigned 16-bit value
Yes
Signed 32-bit value
Yes
Unsigned 32-bit value
Yes
Floating-point number 32-bit IEEE 754
Yes
Floating-point number 64-bit IEEE 754
non-existent in the S5
Text tag, 8-bit character set
No
Text tag, 16-bit character set
non-existent in the S5
Raw data type
No
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.3 Features of the WinCC channel "SIMATIC S5 Profibus FDL"
WinCC side
The communication driver SIMATIC S5 Profibus FDL supports the communication with the
following communication processors:
Communications processor
Bus type
CP5613
PCI
CP5614
PCI
AS side
Automation devices can generally be connected to the PROFIBUS network in two different
ways. The connection can be done via the integrated interface on the central module or with
special communication modules.
System
Modules
S5-90U, S5-95U, S5-100U
CPU95U
S5-115U, S5-135U, S5-155U
CP5431 FMS/DP
Note
With connection to S5-95U with L2-SS, no Fetch connections are possible since WinCC can
only be a passive partner.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
159
S5 PROFIBUS FDL
8.4 Configuring the Channel
8.4
Configuring the Channel
8.4.1
How to configure the channel "SIMATIC S5 Profibus FDL"
Introduction
The steps in configuring the channel "SIMATIC S5 Profibus FDL" are described in this and the
following chapters.
This section shows how the channel "SIMATIC S5 Profibus FDL" is configured.
Procedure
1. Select the entry "Add New Driver" in the shortcut menu of Tag Management. The "Add New
Driver" dialog is opened.
2. Select the "SIMATIC S5 Profibus FDL.CHN" driver and click the "Open" button. The channel
is created and the communication driver is displayed in the tag management.
8.4.2
Channel unit "FDL (CP5412/A2-1)"
Introduction
The communication driver "SIMATIC S5 Profibus FDL" only contains the channel unit "FDL
(CP5412/A2-1)".
The communication between the WinCC and the SIMATIC S5 automation device occurs via
the channel unit "FDL (CP5412/A2-1)". A maximum of 24 connections can be created within
160
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.4 Configuring the Channel
a channel unit. Special connection parameters are to be defined for every configured
connection. Every configured tag must be defined with tag parameters.
Note
The name of the channel unit "FDL (CP5412/A2-1)" is bound to the communication driver,
"SIMATIC S5 Profibus FDL.CHN", and is independent of the communication processor used.
As communication processors, e.g. CP5613 and CP5614 can be used.
Tag parameter
The following tag parameters must be defined for every configured tag:
● Data area (e.g DB)
● Data block number
● Addressing (e.g. "left byte")
● Start address (e.g. DL 0, if "left byte" has been selected for addressing)
Connection parameters
The following connection parameters must be defined for every configured connection:
● The station address of the AS
● The priority
● Own and foreign SAPs (Service Access Point) must be defined for the read and write
function
For the read function, configuring whether it should be an active or a passive connection is
also necessary. For an active read connection, the values are requested from the WinCC
station. For a passive connection, the transfer of the values to the WinCC station is initiated
by the AS.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
161
S5 PROFIBUS FDL
8.4 Configuring the Channel
8.4.3
How to configure a connection
Requirements
● The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
Procedure
1. Open the context menu of channel unit "FDL (CP5412/A2-1)". In this shortcut menu, select
"New Connection".
2. In the "Connection Properties" dialog, enter the connection name.
3. In the "Connection Properties" dialog, click the "Properties" button. The "Connection
Parameters" dialog opens. You can configure the connection in this dialog.
4. Enter the unique address of the AS in the "PLC Station Address" field.
162
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.4 Configuring the Channel
5. The "Priority" option button must always be set to "Low" for an FDL connection.
6. The function of the WinCC station is defined with fields "OS active, WinCC is the active
partner" or "OS passive, WinCC is the passive partner". Activate the required option button.
7. Enter the SAP addresses configured for the reading and writing access in the fields "Own
SAP" and "Foreign SAP". The SAPs value range is between 2 and 54.
8. Click "OK" to close all open dialogs.
9. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens. Configure the tag.
10.Click "OK" to close all open dialogs.
8.4.4
Configuring the tags
8.4.4.1
Configuring the tags
Introduction
For a connection between WinCC and the AS via channel "SIMATIC S5 Profibus FDL", data
types binary, byte and word can be defined within WinCC. The following describes how to
configure a tag of these data types.
8.4.4.2
How to Configure a Tag with Bit by Bit Access
Introduction
This section shows you how to configure a tag for bit by bit access for the address area in the
AS.
Note
The bit by bit access to a tag is only read access.
Requirements
1. The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
2. A connection must be defined in the channel unit "FDL (CP5412/A2-1)".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
163
S5 PROFIBUS FDL
8.4 Configuring the Channel
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter the name of the tag in the "Name" field of the "General" tab, e.g. "binVar1". Define
data type "Binary tag" in the "Data type" field.
3. Click the "Select" button to open the "Address properties" dialog. In the "Data area" set the
data area of the PCL where the data is located. If you select "DB" as data area, enter the
data component in the enabled "DB-No." field.
4. Enter the byte address in field "D" and the bit address in field "Bit". The label on the left
field depends on the entry in the Data Area field, for e.g. "D" for data area "DB" and binary
tag as the data type of the tag.
5. Click "OK" to close all open dialogs.
Note
You cannot change the "Bit" entry in the Addressing field because it is defined by the Binary
tag data type of the WinCC tag.
164
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.4 Configuring the Channel
8.4.4.3
How to Configure a Tag with Byte by Byte Access
Introduction
This section shows you how to configure a tag for byte by byte access for the address area in
the AS.
Note
The byte-wise access to a tag is only read access.
Requirements
1. The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
2. A connection must be defined in the channel unit "FDL (CP5412/A2-1)".
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter the name of the tag in the "Name" field of the "General" tab, e.g. "byteVar1". Define
data type "Unsigned 8 bit value" in the "Data type" field.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
165
S5 PROFIBUS FDL
8.4 Configuring the Channel
3. Click the "Select" button to open the "Address properties" dialog. Define the data area of
the AS in the "Data" field. The communication driver "SIMATIC S5 Profibus FDL" only
supports data areas DB and DX. If you select "DB" as data area, enter the data component
in the enabled "DB-No." field.
4. You can choose between "Left byte" and "Right byte" in the "Addressing" field.
5. Enter the byte address in the "DL" field. The label on the field depends on the entry in the
"Addressing" field, e.g. "DL" for "Left byte" addressing.
6. Click "OK" to close all open dialogs.
8.4.4.4
How to configure a tag with word by word access
Introduction
This section shows you how to configure a tag for word-wise access for the address area in
the AS.
Note
The word by word access to a tag is read and/or write access.
Requirements
1. The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
2. A connection must be defined in the channel unit "FDL (CP5412/A2-1)".
166
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.4 Configuring the Channel
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter the name of the tag in the "Name" field of the "General" tab, e.g. "wordVar1". Set the
data type to "unsigned 16-bit".
3. Click the "Select" button to open the "Address properties" dialog. In the "Data area" set the
data area of the PCL where the data is located. If you select "DB" as data area, enter the
data component in the enabled "DB-No." field.
4. Enter the word address in the field below. The label on the field depends on the entry in
the "Addressing" field, e.g. "DW" for "Word" addressing.
5. Click "OK" to close all open dialogs.
Note
You cannot change the "Word" entry in the "Addressing" field because it is defined by the
"Unsigned 16-bit" data type of the WinCC tag.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
167
S5 PROFIBUS FDL
8.4 Configuring the Channel
8.4.5
System parameters
8.4.5.1
System parameters of the channel unit
Introduction
If you require a configuration that deviates from the standard WinCC settings, you can make
all the required changes using the "System Parameter" dialog of the channel unit.
The following individual points can be changed:
● the device name
● the Write/Read monitoring time
Device Name
Communication between WinCC and the automation system takes place via logical device
names. These names are assigned during the installation of the communication module and
are unit-specific. The device name represents the logical device name. This field is defined
with the entry "/CP_L2_1:/SCP" as default.
Write/Read monitoring time
The write/read monitoring time is the maximum waiting time in seconds for write/read
responses of the AS. If no response is made by the AS within the defined time, the connection
is broken. This field is assigned a waiting time value of 30 seconds as default
Note
The system parameters apply for all CPs in the AS.
168
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.4 Configuring the Channel
8.4.5.2
How to Change the Device Name
Requirements
● The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
Procedure
1. In the channel unit shortcut menu, select "System parameters". The "System Parameters"
dialog opens.
2. Enter the name of the access point in the "Device name" field. This name must match the
setting that you have made under Windows via "Start"
"Settings"
"Control panel"
"Set PG/PC interface".
3. Close the dialog by clicking the "OK" button.
Note
The changes only take effect after WinCC is restarted.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
169
S5 PROFIBUS FDL
8.4 Configuring the Channel
8.4.5.3
How to change the write/read monitoring time of process values
Requirements
● The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
Procedure
1. In the channel unit shortcut menu, select "System parameters". The "System Parameters"
dialog opens.
2. Enter the required value in seconds in the "Maximum waiting time" field. You can define a
value between 1 and 3600 seconds. This field is assigned with a default value of 30 seconds.
3. Close the dialog by clicking the "OK" button.
Note
The changes only take effect after WinCC is restarted.
170
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.5 Special Functions
8.5
Special Functions
8.5.1
Special functions of the "SIMATIC S5 Profibus FDL" Channel
Introduction
The "SIMATIC S5 Profibus FDL" channel has some special functions, the functionality of which
is described in this chapter.
8.5.2
Raw data tags of the "SIMATIC S5 Profibus FDL" channel
8.5.2.1
Raw data tags of the "SIMATIC S5 Profibus FDL" channel
Introduction
A tag of the type "raw data type" is a data telegram.
Raw data tags are required for transferring user data blocks from/to the AS
A raw data tag used by SIMATIC S5 Profibus FDL can be a maximum of 220 bytes in length.
Raw data tag as byte array
A raw data tag as byte array is handled like a normal process tag that is addressed via the
address and length of the data block (for e.g. DB 100, DW 20, length 40 Byte).
Writing raw data tags using scripts
If a raw data tag, which is longer than the tag length configured in WinCC, is written to S5 using
a VB script, the write process is aborted.
Instead write the raw data tag via a C script using the "SetTagRaw" function. For this function,
specify the length of the tags that are to be written.
8.5.2.2
How to configure raw data tags
Requirements
1. The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
2. A connection must be defined in the channel unit "FDL (CP5412/A2-1)".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
171
S5 PROFIBUS FDL
8.5 Special Functions
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter the name of the tag in the "Name" field of the "General" tab, e.g. "Var1_raw_byte".
Select "Raw Data Type" in the "Data type" field.
3. Click the "Select" button to open the "Address properties" dialog.
4. Mark the "Raw Data" check box.
5. Enter the length of the raw data block (in bytes) in the "Length" field.
6. In the "Data area" set the data area of the PLC where the data is located. If you select "DB"
as data area, enter the data component in the enabled "DB-No." field.
7. Set up the addressing type in the "Addressing" field. The entries "Left byte", "Right byte",
"Word" and "Double word" are possible for data type "Raw data type" of the WinCC tag.
8. Enter the value of the start address in the underlying field. The label on the left field depends
on the entry in the Data Area and Addressing field, for e.g. "DW" for data area "DB" "Word"
for addressing type.
9. Click "OK" to close all open dialogs.
172
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.5 Special Functions
8.5.3
Configuring the communication types
8.5.3.1
Configuring the communication types
Introduction
An FDL connection can be configured so that WinCC runs as an active or passive partner.
If WinCC is configured as an active partner, the values are requested by the WinCC station.
If WinCC is configured as a passive partner, the transfer of values to the WinCC station is
initiated by the AS.
8.5.3.2
How to configure an active data transfer
Introduction
This section shows you how to configure an active data transfer to the address area in the AS.
Note
If more than one connection is configured, note that an SAP can only be assigned one time.
Requirements
1. The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
2. A connection must be defined in the channel unit "FDL (CP5412/A2-1)".
3. You must know the SAP address defined by the AS.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
173
S5 PROFIBUS FDL
8.5 Special Functions
Procedure
1. Choose the "Properties" option from the context menu of the connection. The "Connection
Properties" dialog is opened.
2. Click the "Properties" button to open the "Connection parameters" dialog.
3. Enter the station address of the AS in the "PLC Station Address" field on the "Connection"
tab.
4. The following settings must be made in the "READ - Function" area:
5. Activate the option "OS active, WinCC is the active partner".
6. Enter the SAP-ID of the WinCC station in the "Own SAP" field.
7. Enter the SAP-ID of the AS in the "Foreign SAP" field.
8. The following settings must be made in the "WRITE - Function" area:
9. Enter the SAP-ID of the WinCC station in the "Own SAP" field.
174
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.5 Special Functions
10.Enter the SAP-ID of the AS in the "Foreign SAP" field.
11.Click "OK" to close all open dialogs.
8.5.3.3
How to configure a passive data transfer
Introduction
This section shows you how to configure a passive data transfer to the address area in the AS.
Note
If more than one connection is configured, note that an SAP can only be assigned one time.
Requirements
1. The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
2. A connection must be defined in the channel unit "FDL (CP5412/A2-1)".
3. You must know the SAP address defined by the AS.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
175
S5 PROFIBUS FDL
8.5 Special Functions
Procedure
1. Choose the "Properties" option from the context menu of the connection. The "Connection
Properties" dialog is opened.
2. Click the "Properties" button to open the "Connection parameters" dialog.
3. Enter the station address of the AS in the "PLC Station Address" field on the "Connection"
tab.
4. The following settings must be made in the "READ - Function" area:
5. Activate the option "OS passive, WinCC is the passive partner".
6. Enter the SAP-ID of the WinCC station in the "Own SAP" field.
7. Enter the SAP-ID of the AS in the "Foreign SAP" field.
8. The following settings must be made in the "WRITE - Function" area:
9. Enter the SAP-ID of the WinCC station in the "Own SAP" field.
176
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.5 Special Functions
10.Enter the SAP-ID of the AS in the "Foreign SAP" field.
11.Click "OK" to close all open dialogs.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
177
S5 PROFIBUS FDL
8.6 Example of configuring the "SIMATIC S5 Profibus FDL" channel
8.6
Example of configuring the "SIMATIC S5 Profibus FDL" channel
8.6.1
Example of configuring the "SIMATIC S5 Profibus FDL" channel
Introduction
In this example, you will configure an I/O Field in the Graphics Designer and assign the
necessary values to the data handling blocks in the AS.
8.6.2
How to configure the data handling blocks in the AS
Introduction
In this section, you will configure the standard function blocks OB 21 (L2ANLAUF) and OB 1
(L2SNDRCV) in the AS.
By default, the data traffic for the SIMATIC S5 connection by means of PROFIBUS FDL is
handled by means of the following blocks.
Within the example, the following SAP numbers are used:
WinCC
Automation device
SAP number for the READ
function
12
6
SAP number for the WRITE
function
11
4
Blocks
Function
Block
For the startup OB 20, 21, 22
FB-L2ANLAUF (FB 9)
For cyclic operation OB 1
FB-L2SNDRCV (FB 10)
As internal work DBs for both FBs
DB-L2DBVC3 (DB 10)
DB-L2DBVC4 (DB 11)
DB-L2DBVC5 (DB 12)
Startup blocks
The communication parameters are defined in the startup blocks, the work DBs are logged in
and the communication processor is synchronized. These work steps are executed by calling
function block FB9 L2ANLAUF, for example.
178
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.6 Example of configuring the "SIMATIC S5 Profibus FDL" channel
Cyclic block
The telegram traffic is handled in the cyclic FB. Received telegrams are entered in the
destination data blocks. Should an error occur while this is being done, the telegram is rejected
and an error message is issued. Telegrams that have to be sent will be specified by the user
in a similar manner to the standard data handling blocks. An acknowledgement is sent when
the transfer has been completed.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
179
S5 PROFIBUS FDL
8.6 Example of configuring the "SIMATIC S5 Profibus FDL" channel
Requirements
● The data handling blocks SYNCHRON, CONTROL, SEND and RECEIVE must be available
on the automation system.
Procedure
1. The startup block (OB 20, 21, 22) is created in STEP5 by choosing the menu option "Editor"
"STEP5 Block"
"in the program file". The program block is called "L2ANLAUF"
in the example.
2. The following parameters must be preassigned:
– Interface number (SSNR) of the CP (e.g. the CP5431)
– The PROFIBUS address (RADR) of communication processor CP 5613 on the WinCC
computer. This number must be unique in the network.
– The connection parameters of the request types being used, for example, are the
parameters RVC4 (for write) and RVC5 (for read), which specify the SAPs of the WinCC
station. These SAPs are created when the connection is being set up in WinCC.
– The request numbers (ANR4 and ANR5), which are set when the FDL connections are
being configured for the communication processor are
– numbers of the work data blocks, DBX4 (for write) and DBX5 (for read)
3. An OB 1(cyclic operation) is created in the STEP5 software by choosing the menu option
"Editor"
"STEP5 Block"
"in the program file". The program block is called
"L2SNDRCV" in the example.
180
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.6 Example of configuring the "SIMATIC S5 Profibus FDL" channel
4. Communication with WinCC is performed by means of communication processor CP5431
and function block FB10 L2SNDRCV. When WinCC sends data and has to request data,
only two applicable transfer parameters have to be specified for this purpose. These are
the parameters DBX4 (for write) and DBX5 (for read), which specify the numbers of the two
work data blocks for the request types being used. These SAPs are created when the
connection is being set up in WinCC.
5. Load the STEP5 program into the automation device.
This is done in STEP5 by choosing the menu option "Object"
"Blocks"
"Transfer"
"PLC file". Select the option "All blocks" in the "Selection" field to load all previously
created blocks onto the automation system.
8.6.3
How to configure an I/O Field
Introduction
You will configure an I/O Field in this section.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
181
S5 PROFIBUS FDL
8.6 Example of configuring the "SIMATIC S5 Profibus FDL" channel
Requirements
● The channel "SIMATIC S5 Profibus FDL" must be integrated in the project.
Procedure
1. Choose the "New Connection" option from the pop-up menu of the channel unit "FDL
(CP5412/A2-1)" and set up a connection called "TestFDL".
2. By clicking the "Properties" button you can configure the connection parameters.
Enter the station address of the automation system in the " PLC station address" field.
You can configure a FDL connection so that WinCC is either the active or the passive peer.
If WinCC is configured as an active partner, the values are requested by the WinCC station.
If WinCC is configured as a passive partner, the transfer of values to the WinCC station is
initiated by the AS.
Click "OK" to close all open dialogs
3. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
4. Enter tag name "FDLWord1_Test" in the "Name" field. Set the data type to "unsigned 16bit".
5. Click the "Select" button to open the "Address properties" dialog. In the "Data area" set the
data area of the PLC where the data is located. If you select "DB" as data area, enter the
data component in the enabled "DB-No." field. Enter the byte address in the "DW" field.
182
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 PROFIBUS FDL
8.6 Example of configuring the "SIMATIC S5 Profibus FDL" channel
6. Click "OK" to close all open dialogs.
7. You must integrate the smart object "I/O field" into a picture within Graphics Designer.
8. Connect the "I/O field" to a configured tag.
9. Activate the project by clicking the "Activate Runtime" button in the toolbar or by selecting
"Activate Runtime" in the "File" menu. All changes to the configured tag are displayed in
the "I/O field" in Runtime.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
183
S5 Programmers Port AS511
9.1
9
WinCC channel "SIMATIC S5 Programmers Port AS511"
Introduction
The communication driver "SIMATIC S5 Programmers Port AS511" is utilized for the serial
connection through a TTY interface to the SIMATIC S5 automation system.
This chapter describes
● how to configure the data transfer with the "SIMATIC S5 Programmers Port AS511" channel.
● how to configure a connection and a tag.
Channel Unit
The communication driver has one channel unit for controlling a COM port for the serial
connection.
The following capability is available:
● Channel unit S5-AS511 for serial communication via a "Siemens-specific" protocol.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
185
S5 Programmers Port AS511
9.2 Data type of the tags
9.2
Data type of the tags
Introduction
Define the required tags for a logical connection. From the WinCC viewpoint, you can access
the following data types:
● Binary tag
● Unsigned 8-bit value
● Signed 8-bit value
● Unsigned 16-bit value
● Signed 16-bit value
● Unsigned 32-bit value
● Signed 32-bit value
● Floating-point number 32-bit IEEE 754
● Text tag, 8-bit character set
● Raw data type
186
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Programmers Port AS511
9.3 Configuring the Channel
9.3
Configuring the Channel
9.3.1
Configuring the "SIMATIC S5 Programmers Port AS511" channel
Introduction
The following steps are required for configuring the channel "SIMATIC S5 Programmers Port
AS511".
● Configuring the connection
● Configuring the tags
9.3.2
How to configure the connection
Introduction
The process connection using a serial connection is possible with the SIMATIC S5 automation
system. The AS 511 communication processor is used in the automation system.
No additional communication module is required in WinCC. Communication is set up via either
the TTY port on a PG 760 or a COM Port that is part of the system's standard equipment. In
the later case, an additional port converter is required V.24/V.28 <---> TTY.
This serial link supports transmission rates of up to 19200 baud.
The following procedure can be used to assign one of the PC's serial ports to the AS511-NT
drivers.
Note
During communication between WinCC and a S5 automation system via the "AS511"
channel, data blocks may not be transferred, created or deleted in the AS. The memory in
the S5 may also not be compressed. This last restriction is the result of the absolute
addressing of memory in the S5. If changes are necessary, the link to WinCC must be
disconnected.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
187
S5 Programmers Port AS511
9.3 Configuring the Channel
Procedure
1. Select the connection under channel unit "S5-AS511" and open the "Connection properties"
dialog window with menu point "Properties" in the context menu.
2. Click on the "Properties" button. The "Connection parameters" dialog is opened.
3. In the "Port" field, select the port to be used for the serial link.
188
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Programmers Port AS511
9.3 Configuring the Channel
9.3.3
Configuring the tags
9.3.3.1
Configuring the tags
Introduction
For a connection between WinCC and the AS via channel "SIMATIC S5 Programmers Port
AS511", tags of different data types can be created within WinCC. This is described in the
following section.
Note
Addresses of the tags are not checked for plausibility in WinCC. If an address is used, which
is not available in the AS, the status "Addressing error" will be set.
In DB and DX data blocks, reads and writes can only be made up to address 255.
Times cannot be written.
9.3.3.2
How to configure the address of a tag
Introduction
The tag address is entered according to the address structure of the SIMATIC S5.
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select the desired data type (e.g. Signed 8 bit value) from the "General" tab.
3. Click the "Select" button. The "Address properties" dialog is opened.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
189
S5 Programmers Port AS511
9.3 Configuring the Channel
4. Select the "SYSVAR" tab.
5. Click on the selection field to choose whether the tag should transfer the "PLC Type", the
current status ("PLC Status") or other data ("PLC Data").
190
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Programmers Port AS511
9.3 Configuring the Channel
6. Only if you have selected "PLC data" will you have to click on the "Address" tab to define
the S5 address of the tag.
7. Choose whether the tag is located in a data block, in an extended data block, in a flag area,
an input range or an output range in the "Data Area" field.
8. If the tag is in a data block, the "DB No." field is also shown. Here, you enter the number
of the data block.
9. The type of addressing is entered in the "Addressing" field. Normally, the default definition
can be used.
10.Enter the address in the respective field (e.g. "DW ").
Frequently, the memory in the PLC can only be accessed by byte or word. When using binary
and "8 Bit" tags, dialog "Bit-Byte-tag" is opened in addition to dialog "Address properties" and
this can be used to change individual bits in the memory of the PLC as well. For this purpose,
the addressed memory area is read from the PLC for every single write request and the
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
191
S5 Programmers Port AS511
9.3 Configuring the Channel
corresponding bits and/or bytes are modified. Afterwards, the data is written back to the PLC's
memory.
Note
Changes that have been made by the PLC in a read data area are overwritten when writing
back into the data area.
Depending on the type of tag, you can access the automation system's memory bit-wise or
byte-wise.
Addresses of the tags are not checked for plausibility in WinCC. If an address is used, which
is not available in the AS, the status "Addressing error" will be set.
In DB and DX data blocks, reads and writes can only be made up to address 255.
Times cannot be written.
9.3.3.3
How to configure a tag with bit-wise access
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "binary tag" on the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
192
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Programmers Port AS511
9.3 Configuring the Channel
4. Check the "Access to a bit" checkbox and define the addressing for the bit.
5. Click the "Select" button. The "Address properties" dialog is opened.
6. Select the addressing type of the PLC memory in the selection field.
7. Select the number of bit to be changed in the selection field.
9.3.3.4
How to Configure a Tag with Byte by Byte Access
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "Unsigned 8 bit value" or "Signed 8 bit value" in the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
193
S5 Programmers Port AS511
9.3 Configuring the Channel
4. Check the "Access to a byte" checkbox and define the addressing for the byte.
5. Click the "Select" button. The "Address properties" dialog is opened.
6. Select the addressing type of the PLC memory in the selection field.
7. Select the number of byte to be changed in the selection field.
194
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Serial 3964R
10.1
10
WinCC channel "SIMATIC S5 Serial 3964R"
Introduction
The communication driver "SIMATIC S5 Serial 3964R" is implemented for the serial link
between a WinCC station and a SIMATIC S5 automation system.
This chapter describes
● how to configure the data transfer with the "SIMATIC S5 Serial 3964R" channel.
● how to configure a connection and a tag.
Channel Unit
The communication driver has one channel unit for controlling a COM port for the serial link.
The following capability is available:
● Channel unit S5-RK512 (3964R) for serial communication via the 3964R or 3964 protocol.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
195
S5 Serial 3964R
10.2 Data type of the tags
10.2
Data type of the tags
Introduction
Define the required tags for a logical connection. From the WinCC viewpoint, you can access
the following data types:
● Binary tag
● Unsigned 8-bit value
● Signed 8-bit value
● Unsigned 16-bit value
● Signed 16-bit value
● Unsigned 32-bit value
● Signed 32-bit value
● Floating-point number 32-bit IEEE 754
● Text tag, 8-bit character set
● Raw data type
196
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Serial 3964R
10.3 Configuring the Channel
10.3
Configuring the Channel
10.3.1
Configuring the "SIMATIC S5 Serial 3964R" channel
Introduction
The following steps are required for configuring the channel "SIMATIC S5 Serial 3964R".
10.3.2
How to configure the connection
Introduction
The process connection using a serial connection is possible with the SIMATIC S5 automation
system. On the automation system, the communication processor CP 544 or a second, plugin serial port is used on the CPU module (module receptacle SI2).
No additional communication module is required in WinCC. Communication takes place by
means of the default COM ports available on the system.
This serial link supports transmission rates of up to 19200 baud.
Note
When the SIMATIC S5 is actively sending with job type "Pseudowrite", the message length
must not exceed 64 words.
Procedure
1. Select the connection and open the "Connection properties" dialog window with menu point
"Properties" in the context menu.
2. Click on the "Properties" button. The "Connection parameters" dialog is opened.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
197
S5 Serial 3964R
10.3 Configuring the Channel
3. Select the Serial 3964R tab.
4. Select the communications port (COM1 or COM2) for the connection in the "Port" field.
5. Set the data transfer speed to the value used in the "Baud rate" field of the "Procedure
parameters" area. The priority in the case of an initiation conflict (simultaneous line bid by
WinCC and the automation system) is set in the "Priority" field.
The priority has to be set differently from the SIMATIC S5.
6. In the "Procedure data" area, select either the "3964" or "3964R" line protocol. You should
only change the default values for the procedure data (such as acknowledgement time,
character delay time, etc.) in exceptional cases. Make sure that they match the parameters
on the automation system.
198
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Serial 3964R
10.3 Configuring the Channel
7. Now select the "Options" tab.
8. You can disable cyclic life beat monitoring and disable the automatic reconnection on the
"Options" tab.
10.3.3
Configuring the tags
10.3.3.1
Configuring the tags
Introduction
For a connection between WinCC and the AS via channel "SIMATIC S5 3964R", data types
binary and byte can be defined within WinCC. The following describes how to configure a tag
of these data types.
10.3.3.2
How to configure the address of the tag
Introduction
The tag address is entered according to the address structure of the SIMATIC S5.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
199
S5 Serial 3964R
10.3 Configuring the Channel
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select the desired data type (e.g. Signed 8 bit value) from the "General" tab.
3. Click the "Select" button. The "Address properties" dialog is opened.
4. Choose whether the tag is located in a data block, in an extended data block, in a flag area,
an input range or an output range in the "Data Area" field.
5. If the tag is in a data block, the "DB No." field is also shown. Here, you enter the number
of the data block.
6. The type of addressing is entered in the "Addressing" field. Normally, the default definition
can be used.
7. Enter the address in the respective field (e.g. "DL ").
200
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Serial 3964R
10.3 Configuring the Channel
Note
Only read access is possible to the Inputs, Outputs, Timers and Counters address areas.
Read and write access are possible to data blocks (DB, DX).
Do not use data word addresses which are greater than 255. Due a system characteristic of
the RK 512, only the data word addresses 0 to 255 are permissible.
Higher addresses can be configured but lead to data violation on all tags configured in the
connection.
Frequently, the memory in the PLC can only be accessed by byte or word. When using binary
and "8 Bit" tags, dialog "Bit-Byte-tag" is opened in addition to dialog "Address properties" and
this can be used to change individual bits in the memory of the PLC as well. For this purpose,
the addressed memory area is read from the PLC for every single write request and the
corresponding bits and/or bytes are modified. Afterwards, the data is written back to the PLC's
memory.
Note
Changes that have been made by the PLC in a read data area are overwritten when writing
back into the data area.
Depending on the type of tag, you can access the automation system's memory bit-wise or
byte-wise.
10.3.3.3
How to configure a tag with bit-wise access
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "binary tag" on the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
201
S5 Serial 3964R
10.3 Configuring the Channel
4. Check the "Access to a bit" checkbox and define the addressing for the bit.
5. Click the "Select" button. The "Address properties" dialog is opened.
6. Select the addressing type of the PLC memory in the selection field.
7. Select the number of bit to be changed in the selection field.
Note
With the S5, flags, inputs and outputs can be addressed by byte, data blocks (DB, DX) are
addressed by word.
Only read access is possible to the Inputs, Outputs, Timers and Counters address areas.
Read and write access are possible to data blocks (DB, DX).
10.3.3.4
How to Configure a Tag with Byte by Byte Access
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "Unsigned 8 bit value" or "Signed 8 bit value" in the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
202
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
S5 Serial 3964R
10.3 Configuring the Channel
4. Check the "Access to a byte" checkbox and define the addressing for the byte.
5. Click the "Select" button. The "Address properties" dialog is opened.
6. Select the addressing type of the PLC memory in the selection field.
7. Select the number of byte to be changed in the selection field.
Note
With the S5, flags, inputs and outputs can be addressed by byte, data blocks (DB, DX) are
addressed by word.
Only read access is possible to the Inputs, Outputs, Timers and Counters address areas.
Read and write access are possible to data blocks (DB, DX).
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
203
SIMATIC S7 Protocol Suite
11.1
11
"SIMATIC S7 Protocol Suite" Channel
Content
The "SIMATIC S7 Protocol Suite" channel supports communication between a WinCC station
and the SIMATIC S7 automation systems. The suite supports a variety of protocols and types
of networks.
This section shows you
● how to configure various connections and tags for the channel
● how to create a sample project
● how to use the channel's special functions such as the AR_SEND function, raw data tags
and software redundancy
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
205
SIMATIC S7 Protocol Suite
11.2 WinCC Channel "SIMATIC S7 Protocol Suite"
11.2
WinCC Channel "SIMATIC S7 Protocol Suite"
Function principle
The Channel "SIMATIC S7 Protocol Suite" is used to link SIMATIC S7-300 and SIMATIC
S7-400 automation systems.
Depending on the communication hardware used, the system supports connections via the
following channel units:
● Industrial Ethernet and Industrial Ethernet (II): For communication via a communication
processor (such as CP 1612; CP1613) with SIMATIC NET Industrial Ethernet.
● MPI: For communication via the external MPI port of a programming device (e.g. PG 760/
PC RI45), via an MPI communications processor or a communications module (e.g. CP
5511, CP 5613).
● Named Connections: to communicate with STEP 7 via a symbolic connection. These
symbolic connections are configured using STEP 7 and are needed e.g. to provide highavailability communication with the PLC S7-400 in conjunction with the redundancy in H/F
systems.
● PROFIBUS and PROFIBUS (II): For communication via a communication processor (such
as CP 5613) with SIMATIC NET PROFIBUS.
● Slot-PLC: to communicate with a Slot PLC (e.g. WinAC Pro) that is installed as a PC card
in the WinCC computer.
● Soft-PLC: to communicate with a Software PLC (e.g. WinAC Basis), that is installed as an
application on the WinCC computer.
● TCP/IP: to communicate with networks using the TCP/IP protocol.
For more information regarding the diagnosis of channels and tags, refer to "Communication
Diagnostics".
Detailed procedures
Communication Manual: The communication manual contains additional information and
extensive examples for the channel configuration. You can download this manual at
"www.siemens.com/automation/csi_de_WW/product".
In the field in the top right corner, enter the order number "6AV6392-1CA06-0AA0" for the
Communication Manual. Click on "Search" to start searching for the manual.
See also
Software Redundancy - Connection-specific internal tags (Page 285)
"SIMATIC S7 Protocol Suite" Channel - Configuration (Page 212)
Overview of the supported data types (Page 211)
Channel unit selection (Page 207)
Diagnosis of Channels and Tags (Page 369)
206
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.3 Channel unit selection
11.3
Channel unit selection
Introduction
To setup a communication link to an existing or planned network, a selection must be made
for:
● one of the channel's channel units
● a suitable communication processor for the WinCC station
● a suitable communication module for a specific automation system
This section provides an overview of the various options.
There are two different types of communication processors for WinCC:
● Communication processors for the so-called Hardnet. They have their own
microprocessors and reduce the load on the system's CPU. It is possible to use two different
protocols at the same time (multi-protocol operation).
● Communication processors for the so-called Softnet. They do not have their own
microprocessors. Only one protocol can be used at a time (mono-protocol operation).
Channel Unit Assignment
The table below presents the assignment of the channel units of the Channel "SIMATIC S7
Protocol Suite" to networks and automation systems.
Channel unit
of the channel
Communication Network
Automation
system
MPI
MPI
S7-300 and S7-400
PROFIBUS and PROFIBUS (II):
PROFIBUS
S7-300 and S7-400
Industrial Ethernet + Industrial
Ethernet (II)
Industrial Ethernet
S7-300 and S7-400
TCP/IP
Industrial Ethernet
via TCP/IP
S7-300 and S7-400
Named Connections
Industrial Ethernet or
PROFIBUS
S7-400 H/F Systems
Slot PLC
"Soft K-Bus" (internal)
PC (internal)
Soft PLC
"Soft K-Bus" (internal)
PC (internal)
MPI
For communication with the S7-300 and S7-400 PLCs via MPI, Channel "SIMATIC S7 Protocol
Suite" includes the "MPI" channel unit.
The MPI network corresponds in largest part to the PROFIBUS network with preset parameters
and limitations with regard to the number of subscribers and the transfer rate. The same
communication processors and modules are used for communication via MPI as for the
PROFIBUS network. The same communication protocols are also used.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
207
SIMATIC S7 Protocol Suite
11.3 Channel unit selection
Automation System Communication Links
The S7-300 and S7-400 programmable controllers can communicate via a MPI network using
their internal MPI port or a suitable communication module. The table shows the recommended
components.
System
CPU or Communication Module (recommended)
S7-300
CPU 31x
CP 342-5
CP 343-5
S7-400
CPU 41x
CP 443-5 Ext.
CP 443-5 Basic
Communication Processors for WinCC
The following table shows the communication processors recommended for connecting a
WinCC station to a MPI network. Only one communication processor per WinCC computer
can be used for the MPI communication. Each card must also have a driver suitable for the
respective communication protocol.
Communication Processor (WinCC)
Assembly/Type
CP 5613
PCI Card/ Hardnet
CP 5511
PCMCIA Card/ Softnet
CP 5611
PCI Card/ Softnet
PROFIBUS
For communication with the S7-300 and S7-400 PLCs via PROFIBUS, Channel "SIMATIC S7
Protocol Suite" includes the "PROFIBUS" and "PROFIBUS II" channel units.
The channel units support communication via the Hardnet and Softnet modules.
Automation System Communication Links
The S7-300 and S7-400 programmable controllers can communicate via a PROFIBUS network
using their internal port or a suitable communication module. The table shows the
recommended components.
208
System
CPU or Communication Module
S7-300
CPU 31x
CP 342-5
CP 343-5
S7-400
CPU 41x
CP 443-5 Ext.
CP 443-5 Basic
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.3 Channel unit selection
Communication Processors for WinCC
The following table shows the communication processors recommended for connecting a
WinCC station to the PROFIBUS. The "PROFIBUS" channel unit supports communication via
Hardnet and Softnet cards. A WinCC station supports the use of up to two of these modules.
Each communication processor must also have a driver suitable for the respective
communication protocol.
Communication Processor (WinCC)
Assembly/Type
CP 5613
PCI Card/ Hardnet
CP 5511
PCMCIA Card/ Softnet
CP 5611
PCI Card/ Softnet
Industrial Ethernet and TCP/IP
In WinCC, the Channel "SIMATIC S7 Protocol Suite" supports multiple channel units for
communication via Industrial Ethernet:
● "Industrial Ethernet" and "Industrial Ethernet (II)" Channel Units for "ISO" Protocol with S7
Functions
● "TCP/IP" Channel Unit for "ISO-on-TCP" Protocol with S7 Functions
The channel units support communication via the Hardnet and Softnet modules.
Automation System Communication Modules
If the S7-300 or S7-400 PLC should communicate via an Industrial Ethernet using the "ISO"
or "ISO-on-TCP" protocol, it must be equipped with a suitable communication module. The
table shows the recommended components.
System
Communication module
for Industrial Ethernet
Communication module
for TCP/IP-Protocol
S7-300
CP 343-1
CP 343-1 TCP
S7-400
CP 443-1
CP 443-1 TCP
CP 443-1 IT
Communication Processors for WinCC
A WinCC station uses Industrial Ethernet to communicate via the "ISO" or "ISO-on-TCP"
protocol with one of the communication processors recommended in the table below.
Each communication processor also has a driver suitable for each of the respective
communication protocols.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
209
SIMATIC S7 Protocol Suite
11.3 Channel unit selection
210
Communication Processor (WinCC)
Assembly/Type
CP 1612
PCI Card/ Softnet
CP 1613
PCI Card/ Hardnet
CP 1512
PCMCIA Card/ Softnet
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.4 Overview of the supported data types
11.4
Overview of the supported data types
Introduction
For configuring a tag, you need to define data type and type conversion according to the data
format in AS.
The table shows the data types supported by the channel and the use of type conversions.
Supported data types
Data Types
Type conversion
Binary tag
No
Signed 8-bit value
Yes
Unsigned 8-bit value
Yes
Signed 16-bit value
Yes
Unsigned 16-bit value
Yes
Signed 32-bit value
Yes
Unsigned 32-bit value
Yes
Floating-point number 32-bit IEEE 754
Yes
Text tag, 8-bit font
No
Raw data type
No
You will find additional information about type conversion in the "Communication" section.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
211
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
11.5
Configuring the Channel
11.5.1
"SIMATIC S7 Protocol Suite" Channel - Configuration
Introduction
This section will show you how to configure the "SIMATIC S7 Protocol Suite" channel.
1. Installing the Channel
2. Channel unit selection
3. Configuring a connection
4. Tag configuration
System parameter configuration
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
See also
System Parameters of the Channel Unit (Page 236)
Configuring the tags (Page 230)
Channel units of the "SIMATIC S7 Protocol Suite" channel (Page 213)
Diagnosis of Channels and Tags (Page 369)
11.5.2
How to configure the "SIMATIC S7 Protocol Suite" channel
Introduction
This section will show you how to install the "SIMATIC S7 Protocol Suite" channel.
1. Installing the Channel
2. Channel unit selection
3. Creating a connection
4. Inserting a tag
5. Configuring the system parameters in a customized WinCC installation
Prerequisites:
● The communication module is built in.
● The hardware driver has been installed.
● Cable connection to AS exists.
212
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Procedure
1. Select the entry "Add New Driver" in the shortcut menu of Tag Management. A selection
dialog is opened.
2. Select "SIMATIC S7 Protocol Suite.chn" and close the dialog by clicking OK. The channel
is set up and the channel driver is displayed in Tag Management along with the channel
units.
3. Select the desired channel unit and select the "New Connection" entry in the pop-up menu.
4. In the "Connection Properties" dialog, enter the connection name. Close the dialog with the
"OK" button.
5. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
6. Define the name and data type of the tags in the General tab.
Alternately, you can define a start value and a substitute value for the tags in the Limits/
Reporting tab.
For a detailed description about configuring the tags for connecting a specific channel unit,
close the dialog and continue with the topic "Configuring tags" within the respective channel
unit.
7. Click the "Select" button to open the "Address properties" dialog. Set up the address area
of the desired data.
8. Close both of the dialogs by clicking the "OK" button.
9. If your WinCC system and the communication hardware is non-standard, you also need to
set the system parameters to the non-standard values. Additional information on this topic
may be found under "System parameters".
11.5.3
Channel units
11.5.3.1
Channel units of the "SIMATIC S7 Protocol Suite" channel
Introduction
The following chapters describe how to configure the channel units and a corresponding
connection. There can be multiple connections in the same channel unit.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
213
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
See also
"TCP/IP" channel unit (Page 227)
"Soft PLC" channel unit (Page 226)
"Slot PLC" channel unit (Page 224)
Channel Units "PROFIBUS (I + II)" (Page 222)
"Named Connections" channel unit (Page 219)
"MPI" channel unit (Page 217)
Channel Units "Industrial Ethernet" + "Industrial Ethernet (II)" (Page 214)
11.5.3.2
"Industrial Ethernet (I+II)" channel units"
Channel Units "Industrial Ethernet" + "Industrial Ethernet (II)"
Principle of Operation
The channel unit "Industrial Ethernet" is used to connect WinCC to the S7 automation systems
via the Industrial Ethernet. Communication is possible via the communications modules (CP),
e.g. in the case of automation system S7-300 via CP 343-1 and in the case of S7-400 via CP
443-1.
In WinCC different communications processors can be used, e.g. CP 1613. Via the channel
unit "Industrial Ethernet (II)" a second communications processor can be addressed. Because
communication takes place via the "ISO" transport protocol, it is not necessary to configure
the logical connection in the local database.
The function and configurations regarding these channel units are identical.
Typical unit terminology
Communications processor
A communications processor (CP) is a module that supports communication between the
WinCC computer and a specific network.
"ISO" transport protocol
ISO transport is a layer of the ISO-OSI reference model and offers services related to the
transfer of data via connections. The transport layer handles data flow control, blocking and
acknowledgment tasks.
The protocol defines the structure of the data traffic with regards to content on the physical
line. It defines, among other things, the mode of operation, the procedure when establishing
a connection, data backup or the transmission speed.
Industrial Ethernet
The Industrial Ethernet is the most efficient subnet in the industrial environment. It is suitable
for the factory and cell levels and facilitates the exchange of large data volumes over large
distances between a large number of participants.
214
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
The Industrial Ethernet is an open communications network and is standardized in accordance
with IEEE 802.3. Its prime advantages are its speed, simple extendibility and openness as well
as high availability and worldwide utilization. The configuration process requires a minimum
of effort.
See also
Configuring the tags (Page 230)
How to configure a "Industrial Ethernet" channel unit connection (Page 215)
How to configure a "Industrial Ethernet" channel unit connection
Introduction
In addition to the channel unit, WinCC also requires a logical connection to communicate with
the PLC. All the specific parameters are defined while establishing a logical connection.
For S7 automation systems, a communications module, e.g. a CP 343-1 in the S7-300 or a
CP 443-1 in the S7-400, is used for the communication.
A communications processor, for example CP 1613, is used in WinCC. A second
communications processor can be addressed/increased via the "Industrial Ethernet II" channel
unit.
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
Procedure
1. Select the entry "New Connection" in the pop-up menu of the channel unit "Industrial
Ethernet". The "Connection Properties" dialog is opened.
2. Enter a connection name, for example "Test_Ind_Eth", in the General tab.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
215
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
3. Click the "Properties" button to open the "Connection Parameters - Industrial Ethernet"
dialog.
4. Enter the station address of the automation system on the bus in the field "Ethernet
Address".
5. Enter the number of the rack in which the CPU that is to be addressed is located in the
"Rack Number" field.
6. The CPU's slot number in the specified rack must be entered in the corresponding field
"Slot Number".
7. Activate the check box "Send/Receive Raw Data Block" if you wish to transfer BSEND/
BRCV data blocks via the connection. If the check box is active, the field "Connection
Resource" can be edited. Enter the hexadecimal value for the connection resource. This
connection resource will be assigned by STEP7 when the connection is configured in the
PLC.
8. Close both of the dialogs by clicking the "OK" button.
Note
When using an S7-300 or S7-400 with an external communications module, you must enter
the Rack/Slot number of the CPU.
If the wrong Rack or Slot Number is entered, the communications link will not be established!
See also
Configuring the tags (Page 230)
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
Diagnosis of Channels and Tags (Page 369)
216
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
11.5.3.3
"MPI" channel unit
"MPI" channel unit
Principle of Operation
The MPI channel unit is used to connect WinCC to the SIMATIC S7-300 and S7-400
automation systems via MPI.
This can be done in WinCC via
● the internal MPI interface of the programming devices such as PG 760/PC RI45
● a communication processor such as CP 5613 (PCI card)
The so-called MPI module (ISA card) is also suitable - it exists but is hard to get. It was replaced
by the communication processors.
In PLC, linking is done via the MPI interface of the CPU or a corresponding communication
module.
Typical unit terminology
MPI
MPI means Multi Point Interface and is a communication link where there can be multiple
participants. The connection to the communication network takes place as follows:
● In PLC via the MPI interface of the CPU or a communication module,
● In WinCC via the built-in MPI interface, for e.g., of a programming device or a
communication processor (network card).
Communications processor
A communications processor (CP) is a module that supports communication between the
WinCC computer and a specific network.
See also
Configuring the tags (Page 230)
How to configure a "MPI" channel unit connection (Page 217)
How to configure a "MPI" channel unit connection
Introduction
In addition to the channel unit, WinCC also requires a logical connection to communicate with
the PLC. All the specific parameters are defined while establishing a logical connection.
S7-300 and S7-400 PLCs either use the internal MPI interface or a communication module
such as CP 342-5 (SIMATIC S7-300) or CP 443-5 (SIMATIC S7-400).
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
217
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
If WinCC is installed on a PG 760/PC RI45, the internal MPI interface can be used; otherwise,
you need to have a built-in MPI module. Alternately, you can also use a communication module
such as CP 5511 (PCMCIA card).
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
Requirements
● The "SIMATIC S7 Protocol Suite" (communication) driver must be integrated into the
project.
Procedure
1. Select the entry "New Connection" in the pop-up menu of the channel unit "MPI". The
"Connection Properties" dialog is opened.
2. Enter a connection name, for example "Test_MPI", in the General tab.
3. Click the "Properties" button to open the "Connection Parameters - MPI" dialog.
4. Enter the station address in the Station Address field of the automation system on the bus
in the appropriate field.
5. The field "Segment ID" is currently not supported. The value must remain at "0".
6. Enter the number of the rack in which the CPU that is to be addressed is located in the
"Rack Number" field.
7. Enter the "Slot Number" of the CPU in the specified rack.
218
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
8. Activate the check box "Send/Receive Raw Data Block" if you wish to transfer BSEND/
BRCV data blocks via the connection. If the check box is flagged, the field "Connection
Resource" will also be active. Enter the hexadecimal value for the connection resource.
This connection resource will be assigned by STEP7 when the connection is configured in
the PLC.
9. Close both of the dialogs by clicking the "OK" button.
Note
When using an S7-300 or S7-400 with an external communications processor, you must enter
the Rack/Slot number of the CPU.
If the wrong Rack or Slot Number is entered, the communications link will not be established!
While using a S7-300, for the link via the internal MPI interface of the CPU, the rack/ slot
number = 0 must be given.
See also
Configuring the tags (Page 230)
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
11.5.3.4
"Named Connections" channel unit
"Named Connections" channel unit
Principle of Operation
This channel unit is used for setting up a symbolic connection configured using STEP 7. WinCC
can thus access redundant and non-redundant connection via a symbolic connection name.
The symbolic connections are required, for e.g., for high availability communication using
S7-400 PLC in connection with redundancy in H/F systems.
The symbolic connection names are configured in STEP 7 using the NETPRO application.
The connection names, connection parameters and the application names are stored in a
database (*.XDB). This databased is automatically stored by the PLC/OS Engineering Tool
"Mapper" in the corresponding WinCC project directory; however, it can also be copied outside
this directory, for e.g. if you are not using the "Mapper".
Note
There should only be one XDB file per communication participant in the WinCC system.
Hence, a XDB file should not be copied and used on multiple WinCC computers.
You have the following options to activate this database in WinCC:
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
219
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
● If the XDB file is located outside the project directory (for e.g. because the Mapper tool is
not used), you need to enter the path and name of the XDB file in the "Set PG/PC interface"
(Control Panel) in the STEP 7 Configuration tab before starting WinCC.
On starting WinCC, this XDB file is read from this external directory provided no file exists
within the project directory. This procedure is helpful when multiple projects have to use the
same centrally stored database.
● If the Mapper tool is used, it automatically copies the XDB file to the WinCC project directory.
On starting WinCC and opening the project, the data is read from the S7 channel and
entered in the registration database of Windows.
Thereafter, a connection can be configured in WinCC by assigning one of the symbolic
connection names to the selected application name.
Note
The application and connection name can also be entered manually, for e.g. if an XDB file
does not exist for the symbolic connection name or if the project is to be transferred to another
computer. It is necessary to check the correct writing of the name in STEP 7 because there
is no name validation in the CS mode.
Typical unit terminology
Communications processor
A communications processor (CP) is a module that supports communication between the PLC
and a specific network.
See also
Configuring the tags (Page 230)
How to configure a "Named Connections" channel unit connection (Page 220)
How to configure a "Named Connections" channel unit connection
Introduction
In addition to the channel unit, WinCC also requires a logical connection to communicate with
the S7-400 PLC via a symbolic connection.
For setting up a logical connection, one of the symbolic connection names listed in the
"Connection name" field is assigned to a selected application name.
The symbolic connection names and application names are configured in STEP 7.
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
220
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
Procedure
1. Select the entry "New Connection" in the pop-up menu of the channel unit "Named
Connections". The "Connection Properties" dialog is opened.
2. Enter a connection name, for example "Test_NC", in the General tab.
3. Click the "Properties" button to open the "Connection Parameters - Named Connections"
dialog.
4. In the Application name field, enter the application name that has been configured in STEP
7. Default value is WinCC.
5. In the Connection name field, enter the symbolic connection name that has been configured
in STEP 7.
6. Close both of the dialogs by clicking the "OK" button.
Note
The application and connection name can also be entered manually, for e.g. if an XDB file
does not exist for the symbolic connection name or if the project is to be transferred to another
computer. It is necessary to check the correct writing of the name in STEP 7 because there
is no name validation in the CS mode.
See also
Configuring the tags (Page 230)
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
221
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
11.5.3.5
"PROFIBUS (I+II)" channel units
Channel Units "PROFIBUS (I + II)"
Principle of Operation
The channel unit is used to connect WinCC to the SIMATIC S7-300 and S7-400 automation
systems via a PROFIBUS network.
For the S7 automation systems, a communications module is used, e.g. a CP 342-5 in a S7-300
or a CP 443-5 in a S7-400.
A communications processor, for example CP 5613, is used in WinCC.
A second communications processor can be addressed via the "PROFIBUS II" channel unit.
In this manner, the maximum number of connections is increased.
Typical unit terminology
PROFIBUS
The PROFIBUS is an open, nonproprietary communications system for the cell and field levels
and has been designed for a maximum of 127 participants. The PROFIBUS is based on the
European Standard EN 50170, Volume 2, PROFIBUS. PROFIBUS uses token passing with
an underlying master/slave access procedure.
Communications processor
A communications processor (CP) is a module that supports communication between the
WinCC computer and a specific network.
See also
Configuring the tags (Page 230)
How to configure a "PROFIBUS" channel unit connection (Page 222)
How to configure a "PROFIBUS" channel unit connection
Introduction
In addition to the channel unit, WinCC must also have a logical connection to communicate
with the PLC. All the specific parameters are defined while establishing a logical connection.
For S7 automation systems, a communications module is used, e.g. a CP 342-5 in a S7-300
or a CP 443-5 in a S7-400.
A communications processor, for example CP 5613, is used in WinCC. A second
communications processor can be addressed via the "PROFIBUS II" channel unit.
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
222
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
Procedure
1. Select the entry "New Connection" in the pop-up menu of the channel unit "PROFIBUS".
The "Connection Properties" dialog is opened.
2. Enter a connection name, for example "Test_PROFIBUS", in the General Tab.
3. Click the "Properties" button to open the "Connection Parameters - PROFIBUS" dialog.
4. Enter the "Station Address" of the automation system on the bus in the appropriate field.
5. The field "Segment ID" is currently not supported. The value must remain at "0".
6. Enter the "rack number" in which the CPU that is to be addressed is located.
7. Enter the "Slot Number" of the CPU in the specified rack.
8. Activate the check box "Send/Receive Raw Data Block" if you wish to transfer BSEND/
BRCV data blocks via the connection. If the check box is flagged, the field "Connection
Resource" will also be active. Enter the hexadecimal value for the connection resource.
This connection resource will be assigned by STEP7 when the connection is configured in
the PLC.
9. Close both of the dialogs by clicking the "OK" button.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
223
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Note
When starting up the PROFIBUS communication, PROFIBUS errors can occur if the
communication processor was connected to the PROFIBUS while the WinCC computer was
ON. Therefore, it is recommended that the computer be switched OFF before connecting it
to the PROFIBUS. Otherwise, (in accordance with the PROFIBUS standard) multiple tokens
may be generated on the bus, which will cause a bus error.
When using an S7-300 or S7-400 with an external communications module, you must enter
the Rack/Slot number of the CPU.
If the wrong Rack or Slot Number is entered, the communications link will not be established!
See also
Configuring the tags (Page 230)
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
11.5.3.6
"Slot PLC" channel unit
"Slot PLC" channel unit
Principle of Operation
Channel unit "Slot PLC" serves the communication between WinCC and up to four Slot PLC
(WinAC Pro) installed in the WinCC computer. Since the Slot PLC has an integrated interface,
no additional communication hardware is required for the connection between WinCC and Slot
PLC.
See also
Configuring the tags (Page 230)
How to Configure a "Slot PLC" Channel Unit Connection (Page 224)
How to Configure a "Slot PLC" Channel Unit Connection
Introduction
In order to communicate with the installed SPS cards, WinCC requires a logical connection in
addition to the channel unit. All the specific parameters are defined while establishing a logical
connection.
224
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● If several Slot PLC are to be configured, Slot PLC Version 3.4 is required.
Procedure
1. Select the entry "New connection" in the pop-up menu of the channel unit "Slot PLC". The
"Connection Properties" dialog is opened.
2. Enter a connection name, for example "Test_SPLC", in the General tab.
3. Click on the "Properties" button to open the "Connection parameters - Slot PLC" dialog.
4. In the field "Station address", enter the station address of the Slot PLC on the Soft K-Bus.
5. In the field "Slot No.", enter the number of the slot in which the Slot PLC is installed.
6. Activate the check box "Send/Receive Raw Data Block" if you wish to transfer BSEND/
BRCV data blocks via the connection.
7. If the check box is flagged, the field "Connection Resource" will also be active. Enter the
hexadecimal value for the connection resource. This connection resource will be assigned
by STEP 7 when the connection is configured within the PLC.
8. Close both of the dialogs by clicking the "OK" button.
Note
Connection parameters "Station Address" and "Slot No." must be identical for several
installed Slot PLCs and must start with "Slot No." "3".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
225
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
See also
Configuring the tags (Page 230)
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
11.5.3.7
"Soft PLC" channel unit
"Soft PLC" channel unit
Principle of Operation
Channel unit "Slot PLC" serves the communication between WinCC and a Soft PLC (WinAC
Basic) installed in the WinCC computer. No other communication hardware is required for
connecting WinCC to the Soft PLC.
See also
Configuring the tags (Page 230)
How to configure a connection on the "Soft PLC" channel unit (Page 226)
How to configure a connection on the "Soft PLC" channel unit
Introduction
In addition to the channel unit, WinCC must also have a logical connection to communicate
with the Soft PLC. All the specific parameters are defined while establishing a logical
connection.
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
Procedure
1. Select the entry "New connection" in the pop-up menu of the channel unit "Soft PLC". The
"Connection Properties" dialog is opened.
2. Enter a connection name, for example "Test_SOFTPLC", in the General tab.
226
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
3. Click on the "Properties" button to open the "Connection parameters - Soft PLC" dialog.
4. In the field "Station address", enter the station address of the Soft PLC on the Soft K-Bus.
5. In the field "Slot No.", enter the number of the slot. The slot number is configured in the
hardware configuration of Soft PLC and is required when you want to use multiple Soft PLC
in the same WinCC computer.
6. Activate the check box "Send/Receive Raw Data Block" if you wish to transfer BSEND/
BRCV data blocks via the connection.
7. If the check box is flagged, the field "Connection Resource" will also be active. Enter the
hexadecimal value for the connection resource. This connection resource will be assigned
by STEP 7 when the connection is configured within the PLC.
8. Close both of the dialogs by clicking the "OK" button.
See also
Configuring the tags (Page 230)
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
11.5.3.8
"TCP/IP" channel unit
"TCP/IP" channel unit
Principle of Operation
The channel unit "TCP/IP" is used to connect WinCC to the automation systems SIMATIC
S7-300 and S7-400 via an Industrial Ethernet with protocol "ISO-on-TCP Transport".
The protocol corresponds to the standard TCP/IP with the extension RFC 1006. This extension
is necessary, since TCP/IP uses communication where there is no blocking of data.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
227
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
In the case of the automation system S7-300, communication takes place via a
communications module, e.g. CP 343-1 TCP, and via CP 443-1 TCP or CP 443-1 IT in the
case of S7-400.
In WinCC a communications processor such as CP 1613 is used.
Because communication takes place via the ISO-on-TCP transport protocol, it is not necessary
to configure the logical connection in the local database.
Typical unit terminology
Communications processor
A communications processor (CP) is a module that supports communication between the
WinCC computer and a specific network.
ISO transport protocol
ISO transport is a layer of the ISO-OSI reference model and offers services related to the
transfer of data via connections. The transport layer handles data flow control, blocking and
acknowledgment tasks.
The protocol defines the structure of the data traffic with regards to content on the physical
line. It defines, among other things, the mode of operation, the procedure when establishing
a connection, data backup or the transmission speed.
Industrial Ethernet
The Industrial Ethernet is the most efficient subnet in the industrial environment. It is suitable
for the factory and cell levels and facilitates the exchange of large data volumes over large
distances between a large number of participants.
The Industrial Ethernet is an open communications network and is standardized in accordance
with IEEE 802.3. Its prime advantages are its speed, simple extendibility and openness as well
as high availability and worldwide utilization. The configuration process requires a minimum
of effort.
See also
Configuring the tags (Page 230)
How to configure a "TCP/IP" channel unit connection (Page 228)
How to configure a "TCP/IP" channel unit connection
Introduction
In addition to the channel unit, WinCC also requires a logical connection to communicate with
the PLC. All the specific parameters are defined while establishing a logical connection.
In the case of the S7-300 automation system, communication takes place via a
communications module, e.g. CP 343-1 TCP, and via CP 443-1 TCP or CP 443-1 IT in the
case of S7-400.
In WinCC a communications processor such as CP 1613 is used.
228
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
Procedure
1. Select the entry "New Connection" in the pop-up menu of the "TCP/IP" channel unit. The
"Connection Properties" dialog is opened.
2. Enter a connection name, for example "Test_TCP", in the General Tab.
3. Click on the "Properties" button to open the "Connection Parameters - TCP/IP" dialog.
4. Enter the Internet protocol address of the automation system on the bus in the field "IP
Address".
5. Enter the number of the rack in which the CPU that is to be addressed is located in the
"Rack Number" field.
6. The CPU's slot number in the specified rack must be entered in the corresponding field
"Slot Number".
7. Activate the check box "Send/Receive Raw Data Block" if you wish to transfer BSEND/
BRCV data blocks via the connection. If the check box is flagged, the field "Connection
Resource" will also be active. Enter the hexadecimal value for the connection resource.
This connection resource will be assigned by STEP7 when the connection is configured in
the PLC.
8. Close both of the dialogs by clicking the "OK" button.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
229
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Note
When using an S7-300 or S7-400 with an external communications module, you must enter
the Rack/Slot number of the CPU.
If the wrong Rack or Slot Number is entered, the communications link will not be established!
See also
Configuring the tags (Page 230)
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
11.5.4
Configuring the tags
11.5.4.1
Configuring the tags
Introduction
The following sections describe how to configure the tags. It is different in the way the data
area in the PLC is accessed and the data type of the WinCC tags.
Further information regarding the diagnosis of the channel, connection and tags can be found
under "Communication Diagnosis".
See also
How to Configure a Text Tag (Page 234)
How to Configure a Tag with Word by Word Access (Page 233)
How to Configure a Tag with Byte by Byte Access (Page 232)
How to Configure a Tag with Bit by Bit Access (Page 230)
11.5.4.2
How to Configure a Tag with Bit by Bit Access
Introduction
This section shows you how to configure a tag for bit by bit access for the address area in PLC.
230
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection e.g. "Test_Ind_Eth" must be created in a channel unit, e.g. "Industrial
Ethernet".
Procedure
1. Choose the "New Tag" option from the shortcut menu for the "Test_Ind_Eth" connection.
The "Tag Properties" dialog opens.
2. Enter "ETH_Var1_bit" as the name of the tag in the "Name" field. Select "Binary tag" in the
"Data Type" field.
3. Click the "Select" button to open the "Address properties" dialog. In the "Data area" set the
data area of the PCL where the data is located. If you select "DB" as data area, enter the
data component in the enabled "DB-No." field.
4. You cannot change the "Bit" entry in the Addressing field because it is defined by the Binary
Variable data type of the WinCC tag.
5. Enter the byte and bit address in the two fields below it. The label on the left field depends
on the entry in the Data Area field, for e.g. "D" for data area "DB" and Binary Variable as
type.
6. Check the Quality Code check-box if the tag is with Quality Code that is to be used in
WinCC. For this, the code must also exist in the PLC. The check-box is enables only if the
data area is selected as "DB".
7. Close both of the dialogs by clicking the "OK" button.
See also
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
231
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
11.5.4.3
How to Configure a Tag with Byte by Byte Access
Introduction
This section shows you how to configure a tag for byte by byte access for the address area in
PLC.
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection e.g. "Test_Ind_Eth" must be created in a channel unit, e.g. "Industrial
Ethernet".
Procedure
1. Choose the "New Tag" option from the shortcut menu for the "Test_Ind_Eth" connection.
The "Tag Properties" dialog opens.
2. Enter "ETH_Var2_byte" as the name of the tag in the "Name" field. Set the data type to
"unsigned 8-bit".
3. Click the "Select" button to open the "Address properties" dialog. In the "Data area" set the
data area of the PCL where the data is located. If you select "DB" as data area, enter the
data component in the enabled "DB-No." field.
4. You cannot change the "Bit" entry in the Addressing field because it is defined by the
"Unsigned 8-bit" data type of the WinCC tag.
5. Enter the byte addresss in the field below. The label on the left field depends on the entry
in the Data Area field, for e.g. "D" for data area "DB" and Unsigned 8-bit as type.
6. Check the Quality Code check-box if the tag is with Quality Code that is to be used in
WinCC. For this, the code must also exist in the PLC. The check-box is enables only if the
data area is selected as "DB".
7. Close both of the dialogs by clicking the "OK" button.
232
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
See also
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
11.5.4.4
How to Configure a Tag with Word by Word Access
Introduction
This section shows you how to configure a tag for word by word access for the address area
in PLC.
This procedure is also applicable for tags with length of 4 byte ("double word") and more.
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection e.g. "Test_Ind_Eth" must be created in a channel unit, e.g. "Industrial
Ethernet".
Procedure
1. Choose the "New Tag" option from the shortcut menu for the "Test_Ind_Eth" connection.
The "Tag Properties" dialog opens.
2. Enter "ETH_Var3_word" as the name of the tag in the "Name" field. Set the data type to
"unsigned 16-bit".
3. Click the "Select" button to open the "Address properties" dialog. In the "Data area" set the
data area of the PCL where the data is located. If you select "DB" as data area, enter the
data component in the enabled "DB-No." field.
4. You cannot change the "Word" entry in the Addressing field because it is defined by the
"Unsigned 16-bit" data type of the WinCC tag.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
233
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
5. Enter the numeric value of the address in the Addressing field. The label on the left field
depends on the entry in the Data Area field, for e.g. "DBW" for Unsigned 16-bit as type.
6. Check the Quality Code check-box if the tag is with Quality Code that is to be used in
WinCC. For this, the code must also exist in the PLC. The check-box is enables only if the
data area is selected as "DB".
7. Click "OK" to close all open dialogs.
See also
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
11.5.4.5
How to Configure a Text Tag
Introduction
This section show you how to configure a text tag.
For a text tag in the SIMATIC S7 Protocol Suite channel, WinCC only supports S7 string type
consisting of a control word and the actual user data of the string:
● To configure a text tag in WinCC, enter the address of the control word that exists in the
PLC memory before the user data. The first byte of the control word contains the customized
maximum length of the string, the second byte the actual length.
● To insert the data structure in the PLC memory, you must note that the length of the text
tag configured in WinCC is extended by 2 bytes of the control word. If the data structures
of the text tag are inserted in the memory directly one after the other, then the subsequent
data will get overwritten.
● New mapping is required for switching the PCS-7 version from V4.01 to V5.0 SP1 because
in the versions before V5.0 the address of the user data was also mentioned while
configuring the text tags; from version V5.0 onwards the address of the control word is to
be given.
● While reading, the control word is read along with the user data and the current length is
evaluated in the second byte. Only the user data according to the current length included
in the second control byte is trasferred at the text tags of WinCC.
● While writing, the actual length of the string is ascertained ("0" character) and the control
byte with the current length is sent to the PLC along with the user data.
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection e.g. "Test_Ind_Eth" must be created in a channel unit, e.g. "Industrial
Ethernet".
234
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Procedure
1. Choose the "New Tag" option from the shortcut menu for the "Test_Ind_Eth" connection.
The "Tag Properties" dialog opens.
2. Enter "ETH_Var3_Text" as the name of the tag in the "Name" field. In the Data Type field,
set "Text tag, 8-bit font" as the data type. Enter the tag length in bytes in the Length field.
3. Click the "Select" button to open the "Address properties" dialog. In the "Data area" set the
data area of the PCL where the data is located. If you select "DB" as data area, enter the
data component in the enabled "DB-No." field.
4. The entry in the Addressing field can only be changed to Byte or Word because it is defined
by the "Text tag, 8-bit font" data type of the WinCC tag.
5. Enter the numeric value of the address in the Addressing field. Mention the address of the
control word. The label on the left field depends on the entry in the Data Area field, for e.g.
"DBW" for Word as type.
6. Check the Quality Code check-box if the tag is with Quality Code that is to be used in
WinCC. For this, the code must also exist in the PLC. The check-box is enables only if the
data area is selected as "DB".
7. Click "OK" to close all open dialogs.
See also
How to configure the "SIMATIC S7 Protocol Suite" channel (Page 212)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
235
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
11.5.5
System parameters
11.5.5.1
System Parameters of the Channel Unit
Introduction
If you require a configuration that deviates from the WinCC standard settings, you will therefore
be able to make all the required changes using the "System Parameter" dialog of the channel
unit.
The following can be modified:
● the logical device name
● the use of the cyclic read service in the AS
Logical Device Name
Communication between WinCC and the automation system takes place via logical device
names. These names are assigned during the installation of the communications card and are
unit-specific. This field will be filled with a default unit-specific entry, e.g. "MPI" in the case of
channel unit "MPI".
Using cyclic reading services in the PLC
It is possible to specify whether or not the cyclic read services of S7-PLC (also referred to as
cyclic tag services) should be used. These cyclic read services group the tags that are to be
read cyclically into individual request and transfer these to the PLC. The PLC will transfer the
required data immediately on receipt of the request and will also transfer the data each time
the cycle time elapses.
When the cyclic read services are activated, modification transfers can also be used. The data
will then only be transferred when the values have changed. The function must be supported
by the PLC.
Note
The system parameters on the SIMATIC S7 and Unit tabs are unit-specific and can thus be
set separately for each channel unit of the channel.
See also
How to Change the Logical Device Name (Page 240)
How to Configure the System Parameters (Page 238)
Cyclic read services in PLC (Page 237)
236
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
11.5.5.2
Cyclic read services in PLC
Introduction
In the system parameters of the "SIMATIC S7 Protocol Suite" channel, it is also possible to
specify whether or not the cyclic read services of the S7-AS(also referred to as cyclic tag
services) should be used. These cyclic read services group the tags that are to be read
cyclically into individual request and transfer these to the PLC. The PLC will transfer the
required data immediately on receipt of the request and will also transfer the data each time
the cycle time elapses. When the requested data is no longer required, e.g. in the case of a
screen change, WinCC will delete the cyclic read service in the PLC.
In normal cases, use should be made of the cyclic read services in the PLC. For this reason,
the corresponding check box is already activated (default setting) in the system parameters
of the channel unit. This setting should only be changed if you do not wish to use the cyclic
services.
Modification transfers can only be used when the cyclic read services are activated. The data
will then only transferred from the AS when a value has changed and only once per AS cycle.
The function must be supported by the PLC.
The use of the cyclic read services and modification transfers relieves both the AS and AS-OS
communication, since read requests need not be continually sent to the AS and processed
there.
In the case of acyclic read services, the tags that are to be read are combined in an individual
request and transferred to the PLC. The PLC only sends the required data once. The formation
of the cycle for the request is carried out by WinCC.
The number of cyclic read services in a CPU
The number of cyclic read services will depend on the resources that are available in the S7PLC. A maximum of four cyclic services are available for an S7-300 max. and a maximum of
32 for an S7-416 or 417. This number applies for all participants communicating with the PLC,
i.e. if several WinCC systems are communicating with an S7-PLC, they will have to share the
resources that are available. If the maximum number of resources is exceeded, access to a
further cyclic read service will be refused. WinCC will then have to request this data using
acyclic read requests and will also have to execute cycle formation.
Requesting external tags in scripts
The utilization of the cyclic read service has no influence on the initial update once a picture
has been opened if the picture that has been selected does not contain any scripts that request
external tags using the function "GetTagWord()". If scripts are executed with "GetTagWord()"
when a picture is opened, the incorrect configuration of this script could result in new tag
requests being sent to this channel repeatedly following a picture change. If external tags are
required in a script, "Tag" should be entered as a trigger event.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
237
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
11.5.5.3
How to Configure the System Parameters
Introduction
In this section, we will show you how to configure the system parameters of the Channel
"SIMATIC S7 Protocol Suite".
The "System Parameters" dialog comprises two tabs:
● SIMATIC S7 tab
● Unit tab
The system parameters on the SIMATIC S7 and Unit tabs are unit-specific and can thus be
set separately for each channel unit of the channel.
These tabs are identical for all channel units of the S7 channel. Consequently, the dialog for
the channel unit "MPI" is used in all examples.
Any changes that are made to the parameter values will only take effect after WinCC has been
restarted.
Note
When copying the project to another computer, the settings on the Unit tab will be retained,
the settings on the SIMATIC S7 tab, however, will not.
238
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
Procedure
1. Select the Channel "SIMATIC S7 Protocol Suite" in Tag Management. Open the dialog
"System Parameters" using the pop-up menu of the desired channel unit.
2. Select the SIMATIC S7 tab. Place a tick in the check boxes "by AS" and "with modification
transfer", if you want to activate cyclic reading of tags by the channel and the use of
modification transfers. If available, the cyclic services in the PLC will be used here. Further
information can be found under "PLC Cyclic Read Services".
3. Activate the check box "Enable" in the "Lifebeat Monitoring" area if you wish to use this
function. In the Interval field enter the time interval in seconds for transferring the lifebeat
telegrams.
In the Monitoring Time field enter the seconds value for monitoring the response to a lifebeat
telegram.
4. If WinCC should indicate that communication is faulty when the S7-CPU is in the Stop
status, activate the check box "Enable" in the "CPU Stop Monitoring" area.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
239
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
5. Select the Unit tab. A name, which will depend on the communications processor installed,
will be displayed in the field "Logical Device Name". You should only change this name if
you have selected a different name when installing the communications processor. Further
information can be found under "Changing Logical Device Names".
6. If only one communications processor has been installed for this communication type,
activate the check box "Set Automatically", if the device name should be set automatically
when Runtime is started.
7. Activate the check box "Write with Priority", if the processing of write requests should take
priority over the processing of read requests.
8. Close the dialog with the "OK" button.
See also
How to Change the Logical Device Name (Page 240)
Cyclic read services in PLC (Page 237)
11.5.5.4
How to Change the Logical Device Name
Introduction
Communication with the S7 takes place via logical device names. These names are assigned
during the installation of the communications processor and are unit-specific.
Certain presettings have now been established for the device names depending on the
communications processor that has been installed. These are listed in the table "Default Device
Names" below.
The tabs for all units of the S7 channel are identical and, for this reason, the dialog for the
channel unit "MPI" is shown in the description.
240
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.5 Configuring the Channel
Default Device Names
Channel Unit
Default Device Name
Industrial Ethernet
CP_H1_1:
Industrial Ethernet (II)
CP_H1_2:
MPI
MPI
Named Connections
VM/
PROFIBUS
CP_L2_1:
PROFIBUS (II)
CP_L2_2:
Slot PLC
SLOT_PLC
Soft PLC
SOFT_PLC
TCP/IP
CP-TCPIP
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection must be created to a channel unit e.g. "MPI".
Procedure
1. Select the desired channel unit in Tag Management.
2. Open the dialog window "System Parameters" using the pop-up menu.
3. Select the Unit tab.
4. Specify a device name in the field "Logical Device Name". You can either select an entry
from the selection list or enter a new name manually.
All possible names will be determined by the "Configure PG/PC Interface" (Control Panel)
tool. If this has not been installed, only the device name that is currently set will be displayed.
If you specify a different logical device name, a message will be displayed.
Manual entries should only be made if the target station uses a communications card which
is not installed on the configuring station.
5. Close the dialog by clicking the "OK" button.
Note
Logical devices names must be exactly the same - to the letter - as in the device settings.
This being the case, the default logical device names for the "Industrial Ethernet"and
"PROFIBUS" have, for example, a colon at the end of the name.
Any changes that are made to the parameter values will only take effect after WinCC has
been restarted.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
241
SIMATIC S7 Protocol Suite
11.6 Special functions
11.6
Special functions
11.6.1
Special functions of the "SIMATIC S7 Protocol Suite" Channel
Introduction
The SIMATIC S7 Protocol Suite contains some special functions; their functionality is
described in this chapter.
See also
Software Redundancy (Page 283)
Raw data tags of the Channel "SIMATIC S7 Protocol Suite" (Page 275)
Data exchange with the S7 function block AR_SEND (Page 242)
11.6.2
Data exchange with the S7 function block AR_SEND
11.6.2.1
Data exchange with the S7 function block AR_SEND
Introduction
The S7 function block AR_SEND in the S7-400 AS is used to transfer process values to the
process value archives.
Principle of Operation
To transfer PLC process values to a process value archive in WinCC, the S7-400 PLC has an
integrated function component called SFB 37 "AR_SEND".
The basic function of AR_SEND component can supply data to archive tag. Data can be
supplied to multiple tags if the AR_ID-Subnumber is used. If AR_SEND component is used,
the process values are not sent individually to the archive; they are first collect in PLC and
transferred as a package. This reduces the load on the used network.
In a PLC, you can use a CPI-dependent number of AR_SEND components (for e.g. CPU 416
max. 32 AR_SEND). A AR_ID can in turn be assigned to aach AR_SEND component. The subnumber is used to increase the amount of transferable process data because up to 4095 subnumbers are possible for each AR_ID.
In reality, the number of archive tags per AR_SEND component is limited by the maximum
length of the data area to be transferred. For more information about "The Structure and
Parameters of Data Block Structures", please see the description of the "Number of Process
Values" parameter.
AR_ID and AR_ID-Subnumber establish the assignment between data in the PLC and the
archive tags and are defined using other parameters while configuring the data structure in
242
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
the databases in the PLC.
This assignment is configured in WinCC where as the other parameters are evaluated
automatically.
SFB 37 "AR_SEND" must have first been configured in the PLC and the data block structure
must have been done because configuration in WinCC is based on these values in the PLC.
For information about configuring the AR_SEND function component can be found in the
S7-400 PLC documentation.
Overview of AR_SEND Variants
Variants:
AR_SEND for ...
Number of processcontrolled archive tags for
each AR_SEND
Intended use
an archive tag
a
For transferring process values for an archive tag
where the process values can also be read in very
small time intervals.
multiple archive tags corresponds to the number
AR_ID-Subnumbers
For transferring process values for multiple
archive tags where the process values can also
be read in very small time intervals.
multiple archive tags
(optimized)
For cyclic data supply to maximum number of
archive tags each one value each at one time
corresponds to the number
AR_ID-Subnumbers
See also
AR_SEND variant for multiple archive tags (Page 255)
How to configure the AR _SEND variant for multiple archive tags (Page 272)
How to configure the AR _SEND variant for an archive tag (Page 269)
AR_SEND variant for multiple archive tags (optimized) (Page 267)
AR_SEND variant for an archive tag (Page 250)
11.6.2.2
Data Block - Structure and Parameters
Introduction
Before data is transferred from a PLC with the "AR_SEND" function block, it is first organized
as one or more data blocks. The structure of a data block depends on various parameters,
e.g. whether a time stamp or the process value's data type is appended to the AR_SEND
variant used.
The parameters used in data blocks are described below. The individual parameter values are
set in the data block in the AS and in the "AR_SEND" function block parameters.
The parameters are checked when the data block is evaluated in WinCC. If WinCC detects an
error in the structure of the data block or if the archive tag configuration does not match the
received data, an entry with the following structure will be recorded in the WinCC Diagnosis
logbook:
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
243
SIMATIC S7 Protocol Suite
11.6 Special functions
"Date, Time, 1003080 ,4 ,user name, computer name, NRMS7PMC, PdeReceive: Unknown
parameter AR_SEND from connection connectionname ...+ additional information for error
description"
If the message system has been configured with the WinCC System Messages, this diagnosis
entry will also trigger the OS process control message numbered 1003080. The text of the
logbook entry will be found in this message's comment.
Structure of a Data Block
Each data block consists of a header and a user data area:
● The header contains information about the process values and their cycle, and possibly a
time stamp.
● The user data area contains the actual process values.
One or more data blocks form the data area to be transferred.
Note
In the data blocks, each line represents two bytes. Process values can be one or more bytes
long, depending on their data type. Further information can be found in the description of the
"Number of Process Values" parameter.
Description of parameters
Header Type
The Header Type defines the type of information that is contained in the header.
244
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Header
Type
Time stamp
AR_ID Subnumber
0
Header without Time Stamp
Header without AR_ID Subnumber
1
Header with Time Stamp
Header without AR_ID Subnumber
8
Header without Time Stamp
Header with AR_ID Subnumber
9
Header with Time Stamp
Header with AR_ID Subnumber
Note
In the case of the header types 0 and 8, the bytes for the time stamp will not be included in
the header. Since these bytes are also not reserved in the data block, the header will be
shortened accordingly by 8 bytes.
AR_ID Subnumber
Establishes the assignment between the AS user data and the WinCC archive tags and is
configured at two positions:
● In WinCC, when configuring the process controlled archive tags
● In the PLC, when setting up the user data area to be transferred
The Subnumber is only relevant for the header types 8 or 9. Valid values for the Subnumber
are in the range from 1 to 4095. The parameter is entered in WinCC as a hexadecimal value
(1 - 0FFF).
Time stamp
The time stamp contains the date and the time in SIMATIC S7 BCD format. The weekday entry
is not utilized by WinCC.
Note
The automation system S7 does not recognize the Summer/Wintertime switching. In the AS
the local Winter time must be set as the system time. The time stamp on Summer or Winter
time is corrected in WinCC by the standardization DLL. The corrected time and Summer/
Winter time ID are then available in the WinCC applications. The corrected time and ID are
then added to the archive e.g. in Tag Logging.
Cycle
The cycle in which the process values are to be read. This parameter is a factor for the units
of time specified under Unit (Range). Data length: Double word.
E.g.:
"Cycle" = 10 ; "Unit(area)" = 4 means: Reading cycle for process values = 10 seconds
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
245
SIMATIC S7 Protocol Suite
11.6 Special functions
Unit (Type)
Specifies the type of time information and modifies the parameter "Number of Process Values".
No.
Meaning
1
The process values are read at equal intervals.
Start time is mentioned in the timestamp of the header and is mandatory. The time interval
between the process values is defined by the time units in the "Units (Range)" and the factor
"Cycle".
2
Each process value has a timestamp
A time stamp given perhaps in the header will not be evaluated. The format corresponds to
the time stamp in the header with a length of 8 bytes.
3
Each process value has a relative time difference in units of time with a data length of 2 words.
The absolute time is the sum of the time stamp in the header (= start time) and the relative
time difference in the time unit set in "Unit(Range)". A time stamp entry in the header is
mandatory.
4
Each process value contains the AR_ID-Subnumber.
The time stamp given in the header applies for the process value. A time stamp entry in the
header is mandatory.
Units (Range)
Specifies the units of time used for Unit (Type) = 1 or 3.
No.
Meaning
1
Reserved
2
Reserved
3
Milliseconds
4
Seconds
5
Minutes
6
Hours
7
Days
Process Data - Data Type
The process values are stored directly in the S7 format.
246
No.
S7 data type
WinCC Data Type
0
BYTE
BYTE
1
WORD
WORD
2
INT
SWORD
3
DWORD
DWORD
4
DINT
SDWORD
5
REAL
FLOAT
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Number of process values
Depending on the entry in "Unit (Type)", the transferred data area can contain a specific
number of process values. The number is limited by the maximum length of the transferred
data area - 16 Kbytes.
Please note the resource restrictions when using the S7 functions "AR_SEND" and "BSEND/
BRCV" to communicate with a S7-400, i.e. no more than 16 Kbytes of data can be
simultaneously sent by the AS to WinCC using AR_SEND and/or BSEND/BRCV.
Note
In the case of the AR_SEND variant "Multiple Archive Tags", the following limitation applies
for this parameter:
The data blocks for the various archive tags must always begin on a word boundary.
Therefore, in the case of the combination "Data Type Process Value" = 0 (BYTE) and "Unit
(Type)" = 1 (Process value with equally spaced time intervals) an even number of process
values (=Bytes) must be entered for the parameter "Number of Process Values". This
restriction only applies for this AR_SEND variant and this combination of data type and "Unit
(Type)".
Example:
1x BSEND with a max. of 16 Kbytes
or 1x AR_SEND with 8 Kbytes + 1x BSEND with 8 Kbytes
or 1x AR_SEND with 10 Kbytes + 1x AR_SEND with 2 Kbytes + 1x BSEND with 4 Kbytes
Unit
(Type)
The meaning of the number of process values
1
Reading process values at equal time intervals:
8000 process values of the data type WORD or INT or 4000 values of data type DWORD,
DINT or REAL can be transferred.
2
Process values with timestamp:
Each element of the user data area consists of a timestamp (8 bytes) and a value. Therefore,
1600 process values of the data type WORD or INT or 1333 values of data type DWORD,
DINT or REAL can be transferred.
3
Process values with time difference:
Each element of the user data area consists of a timestamp (4 bytes) and a value. Therefore,
2666 process values of the data type WORD or INT or 2000 values of data type DWORD,
DINT or REAL can be transferred.
4
Process value contains AR_ID-Subnumber (AR-SEND with multiple variables - optimized)
In Type 4 , the process value consists of one word with the AR_ID-Subnumber (Value range:
1 - 0x0FFF) and one value. Thus, the user data area consists of an array of process values
preceded by AR_ID Subnumbers. Therefore, 3992 process values of the data type WORD
or INT or 2660 values of data type DWORD, DINT or REAL can be transferred.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
247
SIMATIC S7 Protocol Suite
11.6 Special functions
Note
The AR_ID Subnumbers given in the data blocks must all be configured in WinCC. WinCC
will stop interpreting the user data, if a not-configured subnumber is found.
The data blocks for the various archive tags must always begin on a word boundary.
Therefore, with the data type BYTE and "Unit (Type)" = 1 (Process value with equally spaced
time intervals), an even number of process values (=Bytes) must be entered for the parameter
"Number of Process Values". This restriction only applies for this AR_SEND variant and this
combination of data type and "Unit (Type)".
See also
How to configure the AR _SEND variant for multiple archive tags (Page 272)
How to configure the AR _SEND variant for an archive tag (Page 269)
AR_SEND variant for multiple archive tags (optimized) (Page 267)
AR_SEND variant for multiple archive tags (Page 255)
AR_SEND variant for an archive tag (Page 250)
11.6.2.3
Overview of the properties of the AR_SEND variants
Introduction
On the basis of examples, the tables show the properties and possible parameter values for
different AR_SEND variants.
The tables do not display all of the possible combinations.
The columns "Header Type" to "Process Value Data Type" are presented in the order that they
appear in the header.
Note
The values for AR_ID and AR_ID Subnumber are set together with those of the other
parameters while configuring the function block "AR_SEND" and the data structure in the
data block in the AS.
248
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Variants for an Archive Tag
Example /
Property
E.g.No.
Header
type
Date / Time
(Timestamp
t in header)
Cycle
factor
Unit
(Type)
Units
(range)
AR_IDSubno.
Data type
of
process
val.
max.
number
of
proc.val.
Process
value
structure
in the e.g.
Each
1
process
value (byte)
with its own
time stamp
0
does not
exist
0
2
0
0
0
1; 2
3; 4; 5
3200
1600
1333
8 byte time
stamp
+ 1 Byte
process
value
Process
value with
equally
spaced
time stamp
2
1
Relevant
>=1
1
3 to 7
0
0
1; 2
3; 4; 5
16000
8000
4000
1 word
process
value
Each
process
value
(word) with
its own time
stamp
3
1
not
relevant
0
2
0
0
0
1; 2
3; 4; 5
3200
1600
1333
8 byte time
stamp + 1
word
process
value
Each
process
value with
time
difference
4
1
Relevant
>=1
3
3 to 7
0
0
1; 2
3; 4; 5
5332
2666
2000
8 byte time
stamp
+ 1 Byte
process
value
Variants for Multiple Archive Tags
Example /
Property
E.g.No.
Header
type
Date / Time
(Timestamp
t in header)
Cycle
factor
Unit
(Type)
Units
(range)
AR_IDSubno.
Data type
of
process
val.
max.
number
of
proc.val.
Process
Value
structure in
the e.g.
Each
5
process
value (byte)
with its own
time stamp
8
does not
exist
0
2
0
1 to
4095
0
1; 2
3; 4; 5
3200
1600
1333
8 byte time
stamp
+ 1 Byte
process
value
Process
value with
equally
spaced
time stamp
9
Relevant
>=1
1
3 to 7
1 to
4095
0
1; 2
3; 4; 5
16000
8000
4000
1 word
process
value
6
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
249
SIMATIC S7 Protocol Suite
11.6 Special functions
Example /
Property
E.g.No.
Header
type
Date / Time
(Timestamp
t in header)
Cycle
factor
Unit
(Type)
Units
(range)
AR_IDSubno.
Data type
of
process
val.
max.
number
of
proc.val.
Process
Value
structure in
the e.g.
Each
process
value
(word) with
its own time
stamp
7
9
not
relevant
0
2
0
1 to
4095
0
1; 2
3; 4; 5
3200
1600
1333
8 byte time
stamp
+ 1 word
process
value
Each
process
value with
time
difference
8
9
Relevant
0
3
3 to 7
1 to
4095
0
1; 2
3; 4; 5
5332
2666
2000
8 byte time
stamp
+ 1 Byte
process
value
Variants for Multiple Archive Tags - Optimized
Example /
Property
E.g.No.
Header
type
Date / Time
(Timestamp
t in header)
Cycle
factor
Unit
(Type)
Units
(range)
AR_IDSubno.
Data type
of
process
val.
max.
number
of
proc.val.
Process
value
structure
in the e.g.
Each
process
value with
an AR_ID
Subnumbe
r
9
1
Relevant
0
4
0
0
1; 2
3; 4; 5
3992
2660
1 Word
Subnumber
+ 1 Word
process
value
See also
AR_SEND variant for multiple archive tags (optimized) (Page 267)
AR_SEND variant for multiple archive tags (Page 255)
AR_SEND variant for an archive tag (Page 250)
11.6.2.4
AR_SEND variant for an archive tag
Introduction
This variant can be used to supply an archive tag with process values. It can also be used with
older versions of WinCC (prior to V5.0).
250
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
The properties of this variant:
● The Header Type must be 0 or 1, i.e. without AR_ID Subnumber and with/without time
stamp.
● The AR_ID Subnumber in the header will not be evaluated.
● In WinCC, the archive tag name does not contain an AR_ID Subnumber, since only the
process values for an archive tag will be transferred.
An example of the data area's structure
The data area to be transferred consists of one data block.
See also
Example 4 for data block structure: An archive tag; each process value with relative time stamp
(time difference) (Page 254)
Example 3 for data block structure: An archive tag; each process value has its own time
stamp (Page 253)
Example 2 for data block structure: One archive tag; equally spaced time stamp (Page 252)
Example 1 for data block structure: An archive tag; each process value has a time stamp
(Page 252)
Overview of the properties of the AR_SEND variants (Page 248)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
251
SIMATIC S7 Protocol Suite
11.6 Special functions
11.6.2.5
Example 1 for data block structure: An archive tag; each process value has a time stamp
Introduction
In this example, the process values are transferred for one archive tag only. There is no time
stamp in the header and the corresponding number of bytes are also not reserved. Hence,
each process value (1byte) is preceded by a time stamp (8byte).
Data type of the process values is BYTE.
Data block structure in the data component
See also
Data Block - Structure and Parameters (Page 243)
11.6.2.6
Example 2 for data block structure: One archive tag; equally spaced time stamp
Introduction
In this example, the process values are transferred for one archive tag.
252
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
The equally spaced time stamp of one second is formed using the parameters "Cycle" = 1 and
"Unit (Range)" = 4 (= seconds).
Data type of the process values is WORD.
Data block structure in the data component
See also
Data Block - Structure and Parameters (Page 243)
11.6.2.7
Example 3 for data block structure: An archive tag; each process value has its own time
stamp
Introduction
In this example, the process values are transferred for one archive tag only. The time stamp
in the header is not important. Hence, each process value (1Word) is preceded by a time stamp
(8byte).
Data type of the process values is SWORD.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
253
SIMATIC S7 Protocol Suite
11.6 Special functions
Data block structure in the data component
See also
Data Block - Structure and Parameters (Page 243)
11.6.2.8
Example 4 for data block structure: An archive tag; each process value with relative time
stamp (time difference)
Introduction
In this example, the process values are transferred for one archive tag with time stamp.
The parameter "Unit(Type)" = 3 gives each process value a time difference (4Byte) for the time
stamp in the header. The unit of time difference is set by the parameter "Unit(range)" = 4 in
seconds.
Data type of the process values is DWORD.
254
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Data block structure in the data component
See also
Data Block - Structure and Parameters (Page 243)
11.6.2.9
AR_SEND variant for multiple archive tags
Introduction
With this variant, you can supply process values to one or more archive tags. For each archive
tag, an AR_ID Subnumber will be assigned and a data block will be created in the data area
to be transferred.
"x" process values can be transferred for each AR_ID Subnumber. For more information about
"The Structure and Parameters of Data Block Structures", please see the description of the
"Number of Process Values" parameter.
The time stamp for the value of an archive tag is taken or derived from the data area to be
transferred in accordance with the given "Unit (Type)" and "Unit (Range)". It is then sent on to
the WinCC process value archive.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
255
SIMATIC S7 Protocol Suite
11.6 Special functions
The properties of this variant:
● The Header Type must be 8 or 9 (with/without time stamp and with AR_ID Subnumber).
● For every AR_ID Subnumber, a data block must be created in the data area to be
transferred.
● The AR_ID Subnumber in each data block must be greater than zero.
● In WinCC, the archive tag name has an AR_ID Subnumber.
Note
The AR_ID Subnumbers given in the data blocks must all be configured in WinCC. WinCC
will stop interpreting the user data, if a not-configured subnumber is found.
The data blocks for the various archive tags must always begin on a word boundary.
Therefore, in the case of the combination "Data Type Process Value" = 0 (BYTE) and "Unit
(Type)" = 1 (Process values with equally spaced time intervals) an even number of process
values (=Bytes) must be entered for the "Number of Process Values" parameter. This
restriction only applies for this AR_SEND variant and this combination of data type and "Unit
(Type)".
256
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
An example of the data area's structure
The data area to be transferred consists of one or more data blocks corresponding to the
number of archive tags to be supplied.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
257
SIMATIC S7 Protocol Suite
11.6 Special functions
258
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
See also
Example 8 for data block structure: Multiple archive tags; process values with relative time
stamp (time difference) (Page 265)
Example 7 for data block structure: Multiple archive tags; each process value has its own time
stamp (Page 263)
Example 6 for data block structure: Multiple archive tags; equally spaced time stamp
(Page 261)
Example 5 for data block structure: Multiple archive tags; each process value has its own time
stamp (Page 259)
Overview of the properties of the AR_SEND variants (Page 248)
11.6.2.10 Example 5 for data block structure: Multiple archive tags; each process value has its own
time stamp
Introduction
In this example, process values are transferred for multiple archive tags.
The data blocks for the different archive tags are located one after the other in the data
component. A different AR_ID-Subnumber is entered in each data block.
There is no time stamp in the header and the corresponding number of bytes for it are also
not reserved. Hence, each process value (1byte) is preceded by a time stamp (8byte).
Data type of the process values is BYTE.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
259
SIMATIC S7 Protocol Suite
11.6 Special functions
Data block structure in the data component
See also
Data Block - Structure and Parameters (Page 243)
260
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
11.6.2.11 Example 6 for data block structure: Multiple archive tags; equally spaced time stamp
Introduction
In this example, process values are transferred for multiple archive tags. The data blocks for
the different archive tags are located one after the other in the data component. A different
AR_ID-Subnumber is entered in the header in each data block.
The equally spaced time stamp of one second is formed using the parameters "Cycle" = 1 and
"Unit (Range)" = 4 (= seconds).
Data type of the process values is WORD.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
261
SIMATIC S7 Protocol Suite
11.6 Special functions
Data block structure in the data component
See also
Data Block - Structure and Parameters (Page 243)
262
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
11.6.2.12 Example 7 for data block structure: Multiple archive tags; each process value has its own
time stamp
Introduction
In this example, process values are transferred for multiple archive tags. The data blocks for
the different archive tags are located one after the other in the data component. A different
AR_ID-Subnumber is entered in each data block.
The time stamp in the header is not important. Hence, each process value (1Word) is preceded
by a time stamp (8byte).
Data type of the process values is SWORD.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
263
SIMATIC S7 Protocol Suite
11.6 Special functions
Data block structure in the data component
264
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
See also
Data Block - Structure and Parameters (Page 243)
11.6.2.13 Example 8 for data block structure: Multiple archive tags; process values with relative time
stamp (time difference)
Introduction
In this example, the process values are transferred for one archive tag with time stamp.
The data blocks for the different archive tags are located one after the other in the data
component. A different AR_ID-Subnumber is entered in each data block.
The parameter "Unit(Type)" = 3 gives each process value a time difference (4Byte) for the time
stamp in the header. The unit of time difference is individually defined by the "Unit(Range)"
parameter for each archive tag and hence for each data block.
Data type of the process values is DWORD.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
265
SIMATIC S7 Protocol Suite
11.6 Special functions
Data block structure in the data component
See also
Data Block - Structure and Parameters (Page 243)
266
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
11.6.2.14 AR_SEND variant for multiple archive tags (optimized)
Introduction
This variant is to be used when the maximum number of archive tags should each be supplied
a process value at one time. In this case, the data area to be transferred consists of just one
data block and each process value has just its AR_ID Subnumber and its associated value.
The data type is the same for the process values of all of the archive tags in this data block.
The properties of this variant:
● The Header Type must be 1 (with time stamp and without AR_ID Subnumber).
● The AR_ID Subnumbers for the associated process values in the data block must be greater
than zero. The AR_ID Subnumber in the header will not be evaluated.
● The "Unit (Type)" parameter must be 4, i.e. the process value has an AR_ID Subnumber.
● The "Units (Range)" parameter must be 0, i.e. the time stamp in the Header is valid for all
process values and there are no relative times.
● In WinCC, the archive tag name has an AR_ID Subnumber.
Note
If a process value has an AR_ID Subnumber for which no WinCC archive tag is found, this
will result in an entry in the WinCC Diagnosis Log. The remaining process values will then
continue to be processed.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
267
SIMATIC S7 Protocol Suite
11.6 Special functions
An example of the data area's structure
The data area to be transferred consists of just one data block.
See also
Overview of the properties of the AR_SEND variants (Page 248)
Example 9 for data block structure: multiple archive tags;optimized (Page 268)
11.6.2.15 Example 9 for data block structure: multiple archive tags;optimized
Introduction
In this example, the process values are transferred for one archive tag with time stamp. The
time stamp is applicable to all archive tags.
The corresponding AR_ID-Subnumber is placed before each process value.
Data type of the process values is WORD.
268
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Data block structure in the data component
See also
Data Block - Structure and Parameters (Page 243)
11.6.2.16 How to configure the AR _SEND variant for an archive tag
Introduction
There are a number of variants for using the AR_SEND function to exchange data. For the
"One Archive Tag" variant, only the AR_ID is used. The AR_ID Subnumber is not used.
The AR_ID is used to establish the assignment of the data in the AS to the archive tags and
is configured together with other parameters while configuring the data blocks and the SFB
37 "AR_SEND" function block in the AS.
In WinCC, this allocation is performed in the properties for the process controlled tag. This
assignment is the only configuration that is necessary in WinCC and will be described in this
section.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
269
SIMATIC S7 Protocol Suite
11.6 Special functions
The other parameters in WinCC need not be configured, since they are evaluated
automatically.
Note
To use this variant with just the AR_ID, the Header Type must be configure as 0 or 1. The
AR_ID Subnumber must be set to zero.
Since they do not have an AR_ID Subnumber, all of the archive tags, which were configured
before WinCC Version V5.0, can be used with this variant.
Since WinCC Version 5.1 Hotfix 4 it has been possible to specify an alias for the archive tag
name with process-controlled tags or to use the internal names generated by the system.
The name generated by the system contains the name of the assigned raw data tag instead
of the raw data ID from Version V5.1 HF4. In projects migrated to a version from V5.1 HF4,
the archive tag names can be used in their original format or can be converted. The names
are converted by once opening and closing the properties dialog box of the process-controlled
archive tags. An alias does not have to be assigned.
If in a project all external tags are remapped using the "AS-OS-Transfer" function, the archive
tag name must therefore be converted once to the new structure! The new structure is then
maintained.
Requirements
● The "AR_SEND" function block and the data block structure must first be configured in the
AS and this configuration information must be available during the following procedure.
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection e.g. "Test_Ind_Eth" must be created in a channel unit, e.g. "Industrial
Ethernet".
● A process value archive must be configured in the "Tag Logging" editor.
270
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Procedure
1. In Channel "SIMATIC S7 Protocol Suite", select the connection which should be used for
the data transfer. Choose the "New Tag" option from the shortcut menu for the connection.
The "Tag Properties" dialog opens.
2. Enter "Var_raw_arsend" as the name of the tag in the "Name" field. The name can be no
longer than 24 characters. While configuring the process-controlled tags, the raw data tag
name becomes part of the archive tag name and is therefore limited to the length of the
archive tag name.
In the Data Type field, set the type to Raw Data Type. Click the "Select" button to open the
"Address properties" dialog.
3. Mark the "Raw Data" check box. In the "Raw Data Type" area select the type "Archive Data
Link". Click "OK" to close all open dialogs.
4. Open the "Tag Logging" editor and in the pop-up menu of a process value archive select
"New Process Controlled Tag". The "Properties of process controlled tag" dialog will open.
5. Click on "Select" to open a selection dialog and then select the raw data tag that should be
used to supply the archive tags. In this example that is "VAR_raw_arsend". Close the dialog
with the "OK" button.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
271
SIMATIC S7 Protocol Suite
11.6 Special functions
6. In the "Conversion DLL" field set the entry "nrms7pmc.nll". Click on "Options". The input
dialog will open.
7. Enter the AR_ID as a hexadecimal value. The value is defined through the configuration in
AS.
Uncheck the checkbox "Subnumber" because there is no subnumber used in this
AR_SEND variant.
Close the dialog by clicking "OK".
8. The "Internal Archive Tag Name" field shows the internal archive tag name generated by
the system. It contains the name of the assigned raw data tag and the AR_ID. In the "Archive
Tag Name" field, if required, you can define an alias for this archive tag. If no alias is entered,
the internal archive tag name is used for management in the process value archive and for
addressing the archive tag in WinCC.
9. Close the dialog with the "OK" button.
10.Save your changes and close Tag Logging.
11.6.2.17 How to configure the AR _SEND variant for multiple archive tags
Introduction
There are a number of variants for using the AR_SEND function to transfer data for multiple
archive tags.
● Use the "Multiple Archive Tags" variant to supply multiple values to multiple archive tags
at various times.
● Use the "Multiple Archive Tags - optimized" variant to supply one value each to the
maximum number of archive tags at one time.
The AR_ID and AR_ID Subnumber are used in both of these variants.
AR_ID and AR_ID-Subnumber establish the assignment between the data in the AS and the
archive tag. They are defined in the AS with other parameters when configuring the data blocks
and the function modue SFB 37 "AR_SEND".
In WinCC, this allocation is performed in the properties for the process controlled tag. This
assignment is the only configuration that is necessary in WinCC and will be described in this
272
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
section.
The other parameters in WinCC need not be configured, since they are evaluated
automatically.
Note
To use the AR_ID Subnumber, the Header Type must be configured as 8 or 9.
Archive tags configured in WinCC Version V5.0 have no AR_ID Subnumber and can therefore
only be used in the "One Tag" variant.
Since WinCC Version 5.1 Hotfix 4 it has been possible to specify an alias for the archive tag
name with process-controlled tags or to use the internal names generated by the system.
The name generated by the system contains the name of the assigned raw data tag instead
of the raw data ID from Version V5.1 HF4. In projects migrated to a version from V5.1 HF4,
the archive tag names can be used in their original format or can be converted. The names
are converted by once opening and closing the properties dialog box of the process-controlled
archive tags. An alias does not have to be assigned.
If in a project all external tags are remapped using the "AS-OS-Transfer" function, the archive
tag name must therefore be converted once to the new structure! The new structure is then
maintained.
Requirements
● The "AR_SEND" function block and the data block structure must first be configured in the
AS and this configuration information must be available during the following procedure.
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection e.g. "Test_Ind_Eth" must be created in a channel unit, e.g. "Industrial
Ethernet".
● A process value archive must be configured in the "Tag Logging" editor.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
273
SIMATIC S7 Protocol Suite
11.6 Special functions
Procedure
1. In Channel "SIMATIC S7 Protocol Suite", select the connection which should be used for
the data transfer. Choose the "New Tag" option from the shortcut menu for the connection.
The "Tag Properties" dialog opens.
2. Enter "Var_raw_arsend" as the name of the tag in the "Name" field. The name can be no
longer than 24 characters. While configuring the process-controlled tags, the raw data tag
name becomes part of the archive tag name and is therefore limited to the length of the
archive tag name.
In the Data Type field, set the type to Raw Data Type. Click the "Select" button to open the
"Address properties" dialog.
3. Mark the "Raw Data" check box. In the "Raw Data Type" area select the type "Archive Data
Link". Click "OK" to close all open dialogs.
4. Open the "Tag Logging" editor and in the pop-up menu of a process value archive select
"New Process Controlled Tag". The "Properties of process controlled tag" dialog will open.
5. Click on "Select" to open a selection dialog and then select the raw data tag that should be
used to supply the archive tags. In this example that is "VAR_raw_arsend". Close the dialog
with the "OK" button.
274
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
6. In the "Conversion DLL" field set the entry "nrms7pmc.nll". Click on "Options". The input
dialog will open.
7. Enter the AR_ID as a hexadecimal value. The value is defined through the configuration in
AS.
Activate the "Subnumber" checkbox. Enter the AR_ID Subnumber as a hexadecimal value.
The value is also specified by the configuration in AS.
Close the dialog by clicking "OK".
8. The "Internal Archive Tag Name" field shows the internal archive tag name generated by
the system. It contains the name of the assigned raw data tag, the AR_ID and the AR_ID
Subnumber. In the "Archive Tag Name" field, if required, you can define an alias for this
archive tag. If no alias is entered, the internal archive tag name is used for management in
the process value archive and for addressing the archive tag in WinCC.
9. Close the dialog with the "OK" button.
10.Save your changes and close Tag Logging.
11.6.3
Raw data tags of the Channel "SIMATIC S7 Protocol Suite"
11.6.3.1
Raw data tags of the Channel "SIMATIC S7 Protocol Suite"
Introduction
● A tag of the type raw data type is a data telegram on a transport level. The contents of the
raw data tag are not fixed and therefore only the sender and the receiver can interpret the
transmitted data. There are no format changes in WinCC for this data type. Maximum length
is 65535 Byte.
● WinCC distinguishes between two types of raw data tags: Raw data tag for free application
use and raw data tag for handling S7 functions.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
275
SIMATIC S7 Protocol Suite
11.6 Special functions
Raw data tag for free application use
Raw data tags for free application use are used for transferring user data blocks between
WinCC and PLC and handle only user data. It distinguishes between:
Raw data tag as byte array
Raw data tag for BSEND/BRCV functions
Raw data tag for handling S7 functions
These raw data tags do not have any channel-specific header and are normally used by the
message system and for process data entry in WinCC.
No further description is needed here as these are tags and functions internal to the channel.
See also
Raw data tag for BSEND/BRCV functions of S7 communication (Page 279)
Raw data tag as byte array (Page 276)
11.6.3.2
Raw data tag as byte array
Introduction
Raw data tags as byte array are used for transferring user data blocks between WinCC and
PLC and handle only user data.
A raw data tag as byte array is handled in the channel like a normal process tag that is
addressed via the address and length of the data area (for e.g. DB 100, DW 20, length 40
Byte).
The raw data length is limited to one transferable data block and must be fully transferable
uisng a PDU (Protocol Data Unit). The maximum length of the data blocks that can be
transferred using the communication driver depends on the PDU length negotiated while
establishing the connection minus the header and additional information. The PDU lengths
normally used in SIMATIC S7 thus result in the following maximum lengths:
● S7-300: PDU length 240 Byte, max. data block length 208 Byte
● S7-400: PDU length 480 Byte, max. data block length 448 Byte
Data must be blocked if larger data blocks are to be transferred. In PLC, the S7 software forms
the blocks; in WinCC through scripts.
How to Configure a Raw Data Tag as Byte Array
The raw data tags for transferring data blocks are configured as raw data of "Send/receive
block" type with one address and one length detail.
The following illustration shows a configuration example for a data area with length of 40 bytes
in the data component 100 from data word 20:
276
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Read a Raw data tag as Byte Array
Raw data tag is read in the same way as a "normal" process tag. The corresponding data block
is requested in AS and transferred to the user when the data is received.
Data is transferred always at the initiative of WinCC. Sporadic or event-controlled data
reception at the initiative of AS cannot be done using this raw data tag.
Write a Raw data tag as Byte Array
Raw data tag is written in the same way as a "normal" process tag. After sending the data
block and receiving a positive acknowledgement from AS, the data block is transferred to the
image of the Data Manager.
See also
How to Configure a Raw Data Tag as Byte Array (Page 277)
11.6.3.3
How to Configure a Raw Data Tag as Byte Array
Introduction
This section will show you how to configure as byte array a raw data tag of the "SIMATIC S7
Protocol Suite" channel.
The configuration is identical for all channel units of the channel. The "MPI channel unit and
its connection is used in the example.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
277
SIMATIC S7 Protocol Suite
11.6 Special functions
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection must be created to a channel unit e.g. "MPI".
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter "Var1_raw_byte" as the name of the tag in the "Name" field. Select "Raw Data Type"
in the "Data Type" field.
3. Click the "Select" button to open the "Address properties" dialog.
4. Mark the "Raw Data" check box. In the "Raw Data Type" area select the type "Send/receive
block". The display of the fields in the "Address description" area and the field next to the
checkbox "Raw data" depend on this setting.
5. Enter the length of the raw data block (in bytes) in the Length field.
6. In the "Data area" set the data area of the PCL where the data is located. If data area is
selected as "DB" enter the number of the data component in the enabled "DB-No." field.
The "Cpu" field is disabled for a connection of the "MPI" channel unit.
7. Set up the addressing type in the "Addressing" field. The entries "Byte", "Word" or
"Doubleword" are possible for data type "Raw data type" of the WinCC tag.
8. Enter the value of the start address in the underlying field. The label on the left field depends
on the entry in the Data Area and Addressing field, for e.g. "DBB" for data area "DB" "Byte"
for addressing type.
9. Click "OK" to close all open dialogs.
278
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Note
The raw data length is limited to one transferable data block and must be fully transferable
uisng a PDU (Protocol Data Unit). The maximum length of the data block that can be
transferred using the communication driver depends on the PDU length negotiated while
establishing the connection minus the header and additional information. The PDU lengths
normally used in SIMATIC S7 thus result in the following maximum lengths:
● S7-300: PDU length 240 Byte, max. data block length 208 Byte
● S7-400: PDU length 480 Byte, max. data block length 448 Byte
Wrong length will cause the read/write job to be rejected with a display.
11.6.3.4
Raw data tag for BSEND/BRCV functions of S7 communication
Introduction
Raw data tags for "BSEND/BRCV" functions are used for transferring user data blocks between
WinCC and AS and handle only user data.
This raw data type can be used to access the "BSEND/BRCV" functions of S7 communication.
The functions are available for the following automation systems:
● S7-400
● S7-300
– CPU319-3 PN/DP as of V2.5
– CPU317-2 PN/DP as of V2.6
– CPU315-2 PN/DP as of V3.1
Firmware version V3.x or higher is recommended for S7-300 controllers.
● WinAC RTX 2010
The initiative of data transfer always lies with the sending partner; hence "BSEND/BRCV"
functions can also be used to implement event-controlled or sporadic data block transfers.
For resource reasons, it is advisable to keep the number of BSEND/BRCV raw data tags low.
Resource limitations for using S7 functions "AR_SEND" and "BSEND/BRCV" for
communication with S7-400
The maximum data volume that can be sent simultaneously using AR_SEND and/or BSEND/
BRCV functions from AS to WinCC is limited to 16 kByte.
Example:
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
279
SIMATIC S7 Protocol Suite
11.6 Special functions
● 1x BSEND with a max. of 16 Kbytes
● 1x AR_SEND with 8 kBytes + 1x BSEND with 8 kBytes
● 1x AR_SEND with 10 Kbytes + 1x AR_SEND with 2 Kbytes + 1x BSEND with 4 Kbytes
Note
If the data block of a write job is transferred to AS and has not yet been deleted or fully
deleted from the receiving buffer, then the next write job will be rejected with an error
message. During such an error display, write jobs with R_ID > 0x8000 0000 are written
to a connection-specific queue and the system tries to repeat the write job for 6 seconds.
The responsibility for time co-ordination for transfer rests with the user and needs to be
noted as shorter time intervals for write jobs.
Configuring a PBK Connection for Using "BSEND/BRCV" functions
"BSEND/BRCV" functions can only be used via a "hard-configured connection", a so-called
PBK connection (programmed component communication). To configure a hard-configured
connection, you must mention a connection resource (hex: 10 ... DF) in the connection
parameters. This connection resource will be assigned by STEP 7 when the connection is
configured within the PLC. The connection must be configured in AS as passive connection
end-point.
A hard-configured connection can also be used to handle "normal" read and write jobs. If very
large data areas are to be transferred via the connection, then the data blocks are transferred
in multiple PDUs. For performance reasons, it would therefore be better to create a separate
connection for "BSEND/BRCV" functions.
280
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
Configuring Raw data tag for BSEND/BRCV functions
Raw data tags for transferring "BSEND/BRCV" data blocks are configured as raw data of type
"BSEND/BRCV" with a "R_ID". The data length is derived implicitly from the sent or received
data volume.
"R_ID" Parameter
For the "BSEND/BRCV" functionality, you must specify a 32-bit long R_ID as hexadecimal
number. The R_ID is assigned at the time of configuration in AS and is used for distinguishing
multiple data block transfers over one connection. The send and receive calls are always
notified with reference to this R_ID in the underlying communication sub-system (SIMATIC
Device Drivers). A raw data tag is thus assigned to one unique R_ID.
Sending a "BSEND/BRCV" raw data tag
Sending a "BSEND/BRCV" raw data tag takes place in the same way as writing a "normal"
process tag. After sending the data block and receiving a positive acknowledgement from AS,
the data block is transferred to the image of the Data Manager.
Receiving a "BSEND/BRCV" raw data tag
"BSEND/BRCV" raw data is sproradically sent to the channel on the initiative of the AS. Hence
it is not possible to explicitly read S7 raw data tags.
The BSEND/BRCV mechanisms do not include any synchronization functions. If no user has
logged in to receive the data during the start-up phase, the data blocks sent by AS will bounce
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
281
SIMATIC S7 Protocol Suite
11.6 Special functions
on the receiver side. Hence, the user has to take care of the synchronization and, for e.g.,
release the sending direction on the AS by setting a flag with a data word.
See also
How to Configure a Raw Data Tag for ""BSEND/BRCV" functions (Page 282)
11.6.3.5
How to Configure a Raw Data Tag for ""BSEND/BRCV" functions
Introduction
This section will show you how to configure a raw data tag of the "SIMATIC S7 Protocol Suite"
channel for "BSEND/BRCV" functions.
The configuration is identical for all channel units of the channel. The "MPI channel unit and
its connection is used in the example.
Requirements
● The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
● A connection must be created to a channel unit e.g. "MPI".
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter "Var2_raw_bsend" as the name of the tag in the "Name" field. Select "Raw Data Type"
in the "Data Type" field.
3. Click the "Select" button to open the "Address properties" dialog.
4. Mark the "Raw Data" check box. In the "Raw Data Type" area select the type "BSEND/
BRCV". The display of the fields of the "Address description" area is now deactivated.
282
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
5. Enter the hexadecimal value of the ID in the "R_ID" field. The R_ID is assigned in AS at the
time of configuration
6. Close both of the dialogs by clicking the "OK" buttons.
11.6.4
Software Redundancy
11.6.4.1
Software Redundancy
Introduction
The software redundancy offers a cost-effective option for monitoring the safety-related parts
of the system that do not have time criticality through a redundant connection of two automation
systems S7-300 or S7-400.
Note
The software redundancy of this channel does not have the same functions as the H Layer
Redundancy of SIMATIC S7-400 H.
Configurations in AS and in WinCC are required for functioning.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
283
SIMATIC S7 Protocol Suite
11.6 Special functions
AS
If a redundant connection exists between two automation systems, then in the event of failure
of one AS the other one can take over the monitoring. Monitoring can cover the entire process
or just parts thereof.
Apart from the application program, the software redundancy package is installed on both the
automation systems. This program package is not included in the scope of WinCC delivery.
For matching data, you need a redundancy connection via MPI, PROFIBUS-DP or Industrial
Ethernet between the two automation systems whereby even the existing communication links
can be used.
WinCC
The redundancy connection can also be configured amongst the connection of the same
channel unit. At the time of configuration, only one connection, the so-called main connection
is configured. The reserve connection is only inserted via the Dynamic Wizard "Set up
redundant connection".
The Wizard also inserts the connection-specific internal tags and a script. This controls the
switching between connections during runtime and also the corresponding messages.
During runtime, it is possible to use the script to automatically switch between the connections
when there is an error. However, it is possible to also switch manually without the script by
284
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
describing the connection-specific internal tags
"@<connectionname>@ForceConnectionAddress".
For AS2, you need a second fixed configuration connection if data is to be used from the nonredundant part of AS2 in WinCC.
The use of software redundancy does not means that the hard configured connections can
only be used for the redundancy. Each single connection can also be used without redundance.
See also
How to Clear a Software Redundancy in WinCC (Page 292)
How To Configure a Software Redundancy (Page 289)
Software Redundancy - Connection-specific internal tags (Page 285)
11.6.4.2
Software Redundancy - Connection-specific internal tags
Introduction
Connection-specific internal tags are used to control the redundant connections. These tags
are setup using the Dynamic Wizard "Redundant Connection Configuration" and are gathered
in a Tag Group called "@<connectionname>" in the associated connection.
These tags can be used to determine the connection status and to control the establishment
of a connection. Thus, they can also be used to implement other applications, e.g. the
addressing of multiple PLCs via a single connection. However, if these tags are to be used
without the Software Redundancy package, they must be created manually.
Name Format
The name of a connection-specific internal tag is composed of the name of the associated
connection and an identifier.
"@<connectionname>@<identifier>"
The connection name is prefixed by a "@" to identify it as a system tag. The identifier is placed
as a separator before the connection name.
Example: "@[email protected]"
<connectionname> = CPU_3
<identifier> = ConnectionState
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
285
SIMATIC S7 Protocol Suite
11.6 Special functions
Note
Connection-specific internal tags are counted as external tags (eight external tags per
connection).
WinCC's data manager only permits access to external tags when the associated connection
is ready. The connection-specific internal tags can, however, be written and read regardless
of the connection status.
In Runtime, the current values of some of the connection-specific internal tags may be called
using the "WinCC Channel Diagnosis" tool. When the main connection is selected, the tags
will be displayed in the "Counters" column. In addition, in WinCC Explorers' Tag Management,
it is possible to display the tag's current value as a tooltip.
An Overview of the Tags
The following identifiers are available for the internal tags of Software Redundancy:
ConnectionState
Meaning
Type
Access
Default value
Values
Connection Status
This tag can be used to find out the current connection status.
DWORD
Read
0 = "faulty"
0 = Connection faulty
1 = Connection ready-to-use
2 = Connection redundant (only in case of redundancy in H systems)
ConnectionError
Meaning
Type
Access
Default value
Values
286
Cause of fault
The tag contains a description of the cause for the fault. Default = 0, i.e.
connection not yet established or without error. When establishing a
connection, the tag is loaded with 0 (no error) again. The error code is
interpreted in a channel-specific manner. The S7 channel passes the
SIMATIC Device Driver's error code in this tag.
DWORD
Read
0 = "No error"
0 = No error
<> 0 = S7 Error codes
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
ConnectionErrorString
Meaning
Type
Access
Default value
Values
Cause of fault as string
The tag contains the reason for the connection error as string. The string is
put out in the language currently selected. Default = ", i.e. connection not
yet established or without error. In S7 channel, the following text is output
in "English" regardless of the selected language.
TEXT8 [128]
Read
"" = "No error"
"No Error"
"Error hhhh" = Error hhhh has occurred (whereby hhhh = S7 error code
hexadezimal)
ConnectionErrorCount
Meaning
Type
Access
Default value
Counter for connection error
The value of this tag is incremented by 1 every time there is a connection
error. When there is an overflow, the counting starts back at 0.
DWORD
Read
0
ConnectionEstablishMode
Meaning
Type
Access
Default value
Values
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Connection Establish Mode
This tag can be used to set the automatic mode to establish a connection.
If enabled, the S7 channel attempts to reestablish a failed connection at
intervals of approx. 4 seconds. If the value in this tag = 0, there will be no
attempt after every 4 seconds to reestablish the connection after a fault;
rather it will remain disconnected.
DWORD
Write
1
A Write to the tag brings about the following actions:
0 = Manual connection establish mode
Action: Deactivate automatic connection establishment
<>0 = Automatic connection establishment mode
Action: Activate automatic connection establishment mode
287
SIMATIC S7 Protocol Suite
11.6 Special functions
ForceConnectionState
Meaning
Type
Access
Default value
Values
Preferred connection status
This tag can be used to inform the channel about the preferred connection
status. Usually this tag has the value 1, i.e. the channel attempts to establish
the connection (at regular intervals of approx. 4 seconds, if applicable). If
the value 0 is written to this tag, the channel interrupts the connection.
DWORD
Write
1
Any write to the tag has the following effects:
0 = preferred connection status: Connection broken
Action: if connection established, initiate disconnection
1 = Preferred Connection Status: Connection broken
Action: if connection disconnected, initiate establishment of connection
ForceConnectionAddress
Meaning
Type
Access
Default value
Values
288
Select the connection address
This tag defines which of the connection addresses is to be used to establish
the connection.
DWORD
Write
0
If ConnectionEstablishMode is set to "Automatic", the connection will be
setup automatically to the corresponding address.
A Write to the tag brings about the following actions:
0 = Connection via configured connection parameters
Action: If @ForceConnectionAddress has been earlier set to 1, then initiate
disconnection.
1 = Connection via alternative connection parameters
Action: If @ForceConnectionAddress previously on 0, then initiate
disconnect.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
AlternateConnectionAddress
Meaning
Type
Access
Default value
Values
11.6.4.3
Alternative Connection Address
In this tag, you can enter the alternative connection address string. The
string is the same as the one that will be displayed as the connection
parameter in WinCC Explorer. The string is channel-specific. Upon system
startup (Runtime), the configured address is entered here as default for the
S7 channel. If an address has not been configured yet, the text "Illegal
Address" is entered for the S7 channel.
Example of address detail for a S7-AS with station address 3 via MPI: "MPI,
3 0,,0,0,02"
TEXT8 [255]
Write
"..." = "configured address
Writing to this tag gives rise to the following actions:
- If the address changes due to the write process, then the connection is
disconnected fro the setting "Connection via alternative connection
parameter".
- If connection mode is set to "automatic", then the connection is
automatically established with the address that has just been written.
How To Configure a Software Redundancy
Introduction
This section describes how to configure the software redundancy for connections of the
Channel "SIMATIC S7 Protocol Suite" in WinCC. The PLC must also be configured to use this
function, but this will not be described in this document.
Requirements
1. The Channel "SIMATIC S7 Protocol Suite" must be integrated into the project.
2. A connection must be created in one of this channel's channel-units to which a redundant
connection should be configured.
Procedure
1. In the computer's startup parameters, activate the "Global Script Runtime", "Alarm Logging
Runtime" and "Graphics Runtime" modules.
For further information, please see "Checking startup parameters".
2. Load WinCC's system messages into Alarm Logging. These system messages include
messages about software redundancy.
You can find additional information about the topic under "Read WinCC system messages
in Alarm Logging".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
289
SIMATIC S7 Protocol Suite
11.6 Special functions
3. Open a picture in Graphics Designer. In the "Dynamic Wizard" window select the "System
Functions" tab. Double-click to start the Dynamic Wizard "Setup Redundant Connection".
4. The procedure for using the wizard is described briefly in the "Welcome". Click "Next" to
open the "Set Options" dialog.
5. Select the connection that should be used as the main connection and then click on "Next".
The wizard will now create the connection-specific internal tags and will save them in a tag
group "@" under the main connection.
290
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
6. Enter the address of the PLC to which the reserve connection should be established in the
"Parameter" field.
Mark the "Automatic Switching" check box to have the wizard generate a script for
automatically switching connections.
Click "Next"
A graphic of the redundancy - showing a MPI connection to two PLCs - will appear in the
picture:
7. All of the settings made will be displayed once more in the "Finished!" dialog. If you want
to make any corrections, simply click on "Back". Click "Finish".
The Wizard will now generate a script and save it under "@<connectionname>.pas" in the
directory "C-Editor \ Actions \ Actions : <computername> of the Global Script Editor.
Note
In the following procedure, the "Setup redundant connection" wizard will be used. This wizard
generates - when Step 6 is completed - the connection-specific internal variables. If the wizard
is canceled at this point or the procedure is not completed by clicking on "Finish", these tags
will remain unchanged.
See also
How To Load WinCC's system messages into Alarm Logging (Page 293)
How to Check the WinCC Startup Parameters (Page 292)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
291
SIMATIC S7 Protocol Suite
11.6 Special functions
11.6.4.4
How to Clear a Software Redundancy in WinCC
Introduction
This section describes how to delete the software redundancy for connections of the Channel
"SIMATIC S7 Protocol Suite" in WinCC. The PLC must also be configured to use this function
to return to non-redundant connections, but this is not described in this document.
Requirements
● The WinCC project must be deactivated.
Procedure
A software redundancy is deleted in two steps:
● Delete the tag group "@<computername" including its tags in "Tag Management".
● Delete the script "@<connectionname>.pas" in "Global Script".
Procedure
1. In the Tag Management, select the connection that should be configured as the main
connection for the software redundancy. It contains a tag group "@<connectionname" with
the software redundancy's connection-specific internal tags. Delete this tag group.
2. Delete the script for the Action "@<connectionname>.pas". To do this, open the C-Editor
in "Global Script". Several subdirectories will be displayed.
3. Select the "Actions \ Action : " directory. <computername>". In the data window, delete the
script "@<connectionsname>.pas" for the "Actions" type.
4. Close the "Global Script" editor.
11.6.4.5
How to Check the WinCC Startup Parameters
Procedure
1. In WinCC Explorer, select "Computer".
2. Open the shortcut menu and select "Properties".
3. The "Computer List Properties" dialog is opened. Click the "Properties" button.
4. The "Computer Properties" dialog is opened.
5. Click the "Startup" tab and check the entries. If necessary, activate or deactivate Runtime
modules or add other applications to the startup list.
6. Close the open dialogs.
292
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7 Protocol Suite
11.6 Special functions
11.6.4.6
How To Load WinCC's system messages into Alarm Logging
Introduction
In this section you will see how you can load the WinCC system messages into the project.
Procedure
1. Open Alarm Logging.
2. In "Tools" mneu, use "WinCC System Messages" item to open the "WinCC System
Messages" dialog.
3. In the Create System Messages area, click the "Create only New System Messages" option
button.
4. Click "Create" and close the dialog after completing the transaction.
5. Save your changes and close Alarm Logging.
11.6.4.7
Error codes during connection disturbances
Documentation of Error Codes
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
293
SIMATIC S7-1200, S7-1500 Channel
12.1
12
"SIMATIC S7-1200, S7-1500 Channel" channel
Introduction
The "SIMATIC S7-1200, S7-1500 Channel" channel is used for communication between a
WinCC station and an automation system S7 1200 or S7 1500. Communication takes place
using the TCP/IP protocol.
Note
Data blocks in the TIA Portal must not be configured with "Optimized block access". This
could lead to errors during reading from the database.
Modification of the configuration of the automation system can only be done in the TIA Portal.
Channel unit
The "SIMATIC S7-1200, S7-1500 Channel" channel comes with the "TCP/IP" channel unit.
Recommended communications processors
The following communications processors are recommended for the communication of a
WinCC station with the automation systems S7 1200 or S7 1500:
● CP 1612
● CP 1613
● CP 1512
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
295
SIMATIC S7-1200, S7-1500 Channel
12.2 Overview of the supported data types
12.2
Overview of the supported data types
Introduction
The data type and the format adaptation to the data format in the automation system (AS) are
specified when the tag is configured.
The table shows the data types supported by the channel and the use of type conversions.
Supported data types
296
Data Types
Type conversion
Binary tag
No
Signed 8-bit value
Yes
Unsigned 8-bit value
Yes
Signed 16-bit value
Yes
Unsigned 16-bit value
Yes
Signed 32-bit value
Yes
Unsigned 32-bit value
Yes
Floating-point number 32-bit IEEE 754
Yes
Floating-point number 64-bit IEEE 754
Yes
Text tag, 8-bit font
No
Raw data type
No
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7-1200, S7-1500 Channel
12.3 Configuring the channel
12.3
Configuring the channel
12.3.1
Configuration of the "SIMATIC S7-1200, S7-1500 Channel" channel
Introduction
WinCC needs a logical connection for communication of WinCC with the automation system
(AS). This section describes how to configure the "SIMATIC S7-1200, S7-1500 Channel"
channel.
When implementing the TCP/IP protocol, you must define the IP address of the AS for the
logic connection. The IP address consists of four numerical values, separated by dots. The
numerical values must be within the range of 0-255.
Note
Timeout Behavior
Interrupted connections are not detected immediately when using the TCP/IP protocol. The
check-back message can take up to a minute.
Linkable automation systems
Links can be implemented for the following SIMATIC automation systems:
● S7 1200
● S7 1500
Online Configuration
The Online configuration is not supported.
12.3.2
How to configure a connection
Introduction
The following steps are required for configuring the "SIMATIC S7-1200, S7-1500 Channel"
channel:
1. Configuring a connection
2. Configuring Tags
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
297
SIMATIC S7-1200, S7-1500 Channel
12.3 Configuring the channel
Requirements
● The communication driver for "SIMATIC S7-1200, S7-1500 Channel" channel is installed
and integrated into the project.
● The SIMATIC project is configured and is available in the automation system (AS).
Procedure
1. Open the menu structure for the "SIMATIC S7-1200, S7-1500 Channel" communication
driver in the "Tag Management" editor of the WinCC Explorer.
2. Select the entry "New Connection" in the pop-up menu of the "TCP/IP" channel unit. The
"Connection Properties" dialog is opened.
3. Enter the name of the connection.
4. Click the "Properties" button to open the "New connection" dialog.
5. Enter the IP address of the AS.
6. Select or enter an "access point".
298
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7-1200, S7-1500 Channel
12.3 Configuring the channel
7. If you want to use password protection, click "Options".
Note
Access protection is only possible on the S7 1500 automation system.
8. Enter the password for access protection.
9. Close both of the dialogs by clicking the "OK" button.
12.3.3
Configuring the tags
12.3.3.1
Configuring the tags
Introduction
For a connection between WinCC and the automation system (AS) via "SIMATIC S7-1200,
S7-1500 Channel" channel, tags of different data types can be created in WinCC.
The following sections describe how to configure the tags. The addressing of the data range
in the AS and the data type of the WinCC tags are different.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
299
SIMATIC S7-1200, S7-1500 Channel
12.3 Configuring the channel
12.3.3.2
How to Configure a Tag with Bit by Bit Access
Introduction
This section shows you how to configure a tag for bit by bit access for the address area in the
automation system (AS).
Requirements
● The "SIMATIC S7-1200, S7-1500 Channel" channel must be integrated into the project.
● A connection must be created in the "TCP/IP" channel unit.
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter the name of the tag. Select "Binary tag" in the "Data Type" field.
3. Click the "Select" button to open the "Address properties" dialog. Define the data area in
which the AS data are stored. If you select "DB" as data area, enter the data component
in the enabled "DB-No." field.
4. You cannot change the "Bit" entry in the Addressing field because it is defined by the Binary
Variable data type of the WinCC tag.
5. Enter the byte and bit address in the two fields below it. The label on the left field depends
on the entry in the Data Area field, for e.g. "D" for data area "DB" and Binary Variable as
type.
6. Check the Quality Code check-box if the tag is with Quality Code that is to be used in
WinCC. For this, the code must also exist in the AS. The check-box is enables only if the
data area is selected as "DB".
7. Close both of the dialogs by clicking the "OK" button.
300
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7-1200, S7-1500 Channel
12.3 Configuring the channel
12.3.3.3
How to Configure a Tag with Byte by Byte Access
Introduction
This section shows you how to configure a tag for byte by byte access for the address area in
the automation system (AS).
Requirements
● The "SIMATIC S7-1200, S7-1500 Channel" channel must be integrated into the project.
● A connection must be created in the "TCP/IP" channel unit.
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter name of the tag. Set the data type to "unsigned 8-bit".
3. Click the "Select" button to open the "Address properties" dialog. Define the data area in
which the AS data are stored. If you select "DB" as data area, enter the data component
in the enabled "DB-No." field.
4. You cannot change the "Bit" entry in the Addressing field because it is defined by the
"Unsigned 8-bit" data type of the WinCC tag.
5. Enter the byte addresss in the field below. The label on the left field depends on the entry
in the Data Area field, for e.g. "D" for data area "DB" and Unsigned 8-bit as type.
6. Check the Quality Code check-box if the tag is with Quality Code that is to be used in
WinCC. For this, the code must also exist in the AS. The check-box is enables only if the
data area is selected as "DB".
7. Close both of the dialogs by clicking the "OK" button.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
301
SIMATIC S7-1200, S7-1500 Channel
12.3 Configuring the channel
12.3.3.4
How to Configure a Tag with Word by Word Access
Introduction
This section shows you how to configure a tag for word by word access for the address area
in the automation system (AS).
This procedure is also applicable for tags with length of 4 byte ("double word") and more.
Requirements
● The "SIMATIC S7-1200, S7-1500 Channel" channel must be integrated into the project.
● A connection must be created in the "TCP/IP" channel unit.
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter the name of the tag. Set the data type to "unsigned 16-bit".
3. Click the "Select" button to open the "Address properties" dialog. Define the data area in
which the AS data are stored. If you select "DB" as data area, enter the data component
in the enabled "DB-No." field.
4. You cannot change the "Word" entry in the Addressing field because it is defined by the
"Unsigned 16-bit" data type of the WinCC tag.
5. Enter the numeric value of the address in the Addressing field. The label on the left field
depends on the entry in the Data Area field, for e.g. "DBW" for Unsigned 16-bit as type.
6. Check the Quality Code check-box if the tag is with Quality Code that is to be used in
WinCC. For this, the code must also exist in the AS. The check-box is enables only if the
data area is selected as "DB".
7. Close both of the dialogs by clicking the "OK" button.
302
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC S7-1200, S7-1500 Channel
12.3 Configuring the channel
12.3.3.5
How to Configure a Text Tag
Introduction
This section show you how to configure a text tag.
For a text tag in the "SIMATIC S7-1200, S7-1500 Channel" channel, WinCC only supports S7
string type consisting of a control word and the actual user data of the string:
● To configure a text tag in WinCC, enter the address of the control word that exists in the
automation system memory before the user data. The first byte of the control word contains
the customized maximum length of the string, the second byte the actual length.
● To insert the data structure in the PLC memory, you must note that the length of the text
tag configured in WinCC is extended by 2 bytes of the control word. If the data structures
of the text tag are inserted in the memory directly one after the other, then the subsequent
data will get overwritten.
● While reading, the control word is read along with the user data and the current length is
evaluated in the second byte. Only the user data according to the current length included
in the second control byte is trasferred at the text tags of WinCC.
● While writing, the actual length of the string is ascertained ("0" character) and the control
byte with the current length is sent to the PLC along with the user data.
Requirements
● The "SIMATIC S7-1200, S7-1500 Channel" channel must be integrated into the project.
● A connection must be created in the "TCP/IP" channel unit.
Procedure
1. Choose the "New Tag" option from the shortcut menu for the connection. The "Tag
Properties" dialog opens.
2. Enter the name of the tag. In the Data Type field, set "Text tag, 8-bit font" as the data type.
Enter the tag length in bytes in the Length field.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
303
SIMATIC S7-1200, S7-1500 Channel
12.3 Configuring the channel
3. Click the "Select" button to open the "Address properties" dialog. Define the data area in
which the AS data are stored. If you select "DB" as data area, enter the data component
in the enabled "DB-No." field.
4. The entry in the Addressing field can only be changed to Byte or Word because it is defined
by the "Text tag, 8-bit font" data type of the WinCC tag.
5. Enter the numeric value of the address in the Addressing field. Mention the address of the
control word. The label on the left field depends on the entry in the Data Area field, for e.g.
"DBW" for Word as type.
6. Check the Quality Code check-box if the tag is with Quality Code that is to be used in
WinCC. For this, the code must also exist in the AS. The check-box is enables only if the
data area is selected as "DB".
7. Close both of the dialogs by clicking the "OK" button.
304
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Ethernet Layer 4
13.1
13
WinCC channel "SIMATIC TI Ethernet Layer 4"
Introduction
The communication driver "SIMATIC TI Ethernet Layer 4" handles the link between a WinCC
station and a SIMATIC TI505 automation system via Industrial Ethernet. The communication
is handled with the ISO transport protocol.
This chapter describes
● how to configure the data transfer with the "SIMATIC TI Ethernet Layer 4" channel.
● how to configure a connection and a tag.
Channel units
IT has two channel units to run a maximum of two CP 1613. The functionality of the channel
unit is identical. They differ only in the logical device names of the two CP 1613.
The logical device name can be changed via the system parameters of the channel unit. Here,
it is also possible to set the parameters for the ISO transport protocol.
The following application capabilities exist:
● Channel unit 505 Ethernet (CP 1413-1) for the communication modules for SIMATIC
Industrial Ethernet (e.g. CP 1613).
● Channel unit 505 Ethernet (CP 1413-2) for the communication modules for SIMATIC
Industrial Ethernet (e.g. CP 1613).
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
305
SIMATIC TI Ethernet Layer 4
13.2 Data type of the tags
13.2
Data type of the tags
Introduction
Define the required tags for a logical connection. From the WinCC viewpoint, you can access
the following data types:
● Binary tag
● Unsigned 8 bit value (is only supported by VMS addressing)
● Signed 8 bit value (is only supported by VMS addressing)
● Unsigned 16-bit value
● Signed 16-bit value
● Unsigned 32-bit value
● Signed 32-bit value
● Floating-point number 32-bit IEEE 754
● Raw data type
306
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
13.3
Configuring the Channel
13.3.1
Configuring the channel "SIMATIC TI Ethernet Layer 4"
Introduction
The following steps are required for configuring the channel "SIMATIC TI Ethernet Layer 4".
13.3.2
How to configure the connection
Introduction
The process connection via Industrial Ethernet is possible with the SIMATIC TI505 automation
system. Communication module CP 1434 TF is used in the automation system. The
communication is handled with the ISO transport protocol.
The communication module CP 1613 is used in the WinCC system. Because communication
takes place via the ISO transport protocol, it is not necessary to configure the logical connection
in the local database.
For a logical connection, WinCC establishes one connection in the transport layer for reading
(READ) and one for writing (WRITE). Only if both connections are established is the logical
connection also indicated as being established.
Parameters for the READ function
When configuring the connection, parameters are defined for the READ function in WinCC.
These are independent of the request used in the SIMATIC TI.
WinCC side
SIMATIC TI side
FETCH Active
(Request "READ Active")
READ Passive
(Request "READ Passive")
FETCH Passive
(Request "WRITE Passive")
WRITE Active
(Request "WRITE Active")
Parameters "Own TSAP-ID" and "External TSAP-ID" for the WRITE function
WinCC side
SIMATIC TI side
Request "WRITE Active"
Request "WRITE Passive"
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
307
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
Procedure
1. Select the connection and open the "Connection properties" dialog window with menu point
"Properties" in the context menu.
2. Click on the "Properties" button. The "Connection properties" dialog is opened.
3. Enter the station address of the SIMATIC TI on the industrial Ethernet bus in the field
"Ethernet Address".
4. Now, define the parameters for the READ function in the WinCC system. These are
independent of the request used in the SIMATIC TI.
5. Then, enter the value in the allocated field "Own TSAP-ID" that was configured in the
"Remote parameter" area as "TSAP" while configuring the CP 1434 TF.
6. Now, enter the value in the allocated field "External TSAP-ID" that was configured in the
"Local parameter" as "TSAP" while configuring the CP1434 TF.
7. Define the parameters "Own TSAP-ID" and "External TSAP-ID" for the WRITE function
accordingly.
308
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
13.3.3
Configuring the tags
13.3.3.1
Configuring the tags
Introduction
For a connection between WinCC and the AS via channel "SIMATIC TI Ethernet Layer 4", tags
of different data types can be created in WinCC. The following describes how to configure a
tag of these data types.
13.3.3.2
How to configure the address of a tag
Introduction
The tag address is entered according to the address structure of the SIMATIC TI505.
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select the desired data type for the tags (e.g. Signed 16 bit value) from the "General" tab.
3. Click the "Select" button. If it is a "Binary" or "8-Bit" tag, the "Bit/Byte tag" dialog will now
open. Tick the corresponding check box "Access a Bit/Byte", if data should be written to
the AS memory.
4. Click the "Select" button. The "Address properties" dialog is opened.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
309
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
5. Select the location of the tag in the automation system in the "Address type" field.
Depending the selected address type, more definitions have to be made (e.g. "V-tag
memory" for address type in the "Data element" field).
6. In the field "Read-Only Tag", you can specify that the tag cannot be written by WinCC.
Note
Structure tags are not supported.
A description of address types may be found in the SIMATIC TI505 Technical
Documentation.
Write access to memory areas in the AS can only performed bit-wise or byte-wise in channel
"TI Ethernet Layer 4". When using binary and "8 Bit" tags, dialog "Bit-Byte-tag" is opened in
addition to dialog "Address properties" and this can be used to define write access to individual
bits or bytes. For this purpose, the addressed memory area is read from the AS for every single
write request and the corresponding bits and/or bytes are modified. Afterwards, the data is
written back to the AS's memory.
Note
Changes that have been made by the AS in a read data area are overwritten when writing
back into the data area.
Depending on the type of tag, you can access the memory in the AS bit-wise or byte-wise.
13.3.3.3
How to configure a tag with bit-wise access
Introduction
Write access to memory areas in the AS can only performed bit-wise or byte-wise in channel
"TI Ethernet Layer 4". When using binary and "8 Bit" tags, dialog "Bit-Byte-tag" is opened in
addition to dialog "Address properties" and this can be used to define write access to individual
bits or bytes. For this purpose, the addressed memory area is read from the AS for every single
write request and the corresponding bits and/or bytes are modified. Afterwards, the data is
written back to the AS's memory.
Note
Changes that have been made by the AS in a read data area are overwritten when writing
back into the data area.
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "binary tag" on the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
310
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
4. Check the "Access to a bit" checkbox and define the addressing for the bit.
5. Click the "Select" button. The "Address properties" dialog is opened.
6. Select the addressing type of the PLC memory in the "Address type" selection field.
7. From the list below, select the number of the element to be changed.
Note
A description of address types may be found in the SIMATIC TI505 Technical Documentation.
13.3.3.4
How to Configure a Tag with Byte by Byte Access
Introduction
Write access to memory areas in the AS can only performed bit-wise or byte-wise in channel
"TI Ethernet Layer 4". When using binary and "8 Bit" tags, dialog "Bit-Byte-tag" is opened in
addition to dialog "Address properties" and this can be used to define write access to individual
bits or bytes. For this purpose, the addressed memory area is read from the AS for every single
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
311
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
write request and the corresponding bits and/or bytes are modified. Afterwards, the data is
written back to the AS's memory.
Note
Changes that have been made by the AS in a read data area are overwritten when writing
back into the data area.
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "Unsigned 8 bit value" or "Signed 8 bit value" in the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
4. Check the "Access to a byte" checkbox and define the addressing for the byte.
5. Click the "Select" button. The "Address properties" dialog is opened.
6. Select the addressing type of the PLC memory in the "Address type" selection field.
7. From the list below, select the number of the element to be changed.
312
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
Note
A description of address types may be found in the SIMATIC TI505 Technical Documentation.
13.3.4
System parameters
13.3.4.1
System parameters of the channel unit
Introduction
If you require a configuration that deviates from the standard WinCC settings, you can make
all the required changes using the "System parameters" dialog of the channel unit.
The following individual points can be changed:
● the device name
● the transport parameter
Device Name
Communication between WinCC and the automation system takes place via logical device
names. These names are assigned during the installation of the communication module and
are unit-specific. The device name represents the logical device name. The logical device
name is initially defined as "/CP_H1_1:/SCP" as default.
Transport Parameter
Specific settings for the channel unit are made in the transport parameters, e.g. PDU size,
setup attempts, etc.
Note
The system parameters apply for all CPs in the AS.
13.3.4.2
How to Change the Device Name
Introduction
The process connection via Industrial Ethernet is possible with the SIMATIC TI505 automation
system. Communication module CP 1434 TF is used in the automation system. The
communication is handled with the ISO transport protocol.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
313
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
The communication module CP 1613 is used in the WinCC system. Because communication
takes place via the ISO transport protocol, it is not necessary to configure the logical connection
in the local database.
Requirements
● The channel "SIMATIC TI Ethernet Layer 4" must be integrated in the project.
Procedure
1. Select the channel unit and open dialog window "System parameters" with the context
menu.
2. Select the "Device Name" Tab.
3. Now, you can select the logical device name shown in bold print with the mouse and change
it with a mouse click in the name field.
The logical device name is defined as "/CP_H1_1:/SCP" as default during the hardware
driver installation. Only if you have defined another name there, which is not recommended,
will you have to change the device name here as well.
314
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
13.3.4.3
How to change the transport parameter
Introduction
The process connection via Industrial Ethernet is possible with the SIMATIC TI505 automation
system. Communication module CP 1434 TF is used in the automation system. The
communication is handled with the ISO transport protocol.
The communication module CP 1613 is used in the WinCC system. Because communication
takes place via the ISO transport protocol, it is not necessary to configure the logical connection
in the local database.
Requirements
● The channel "SIMATIC TI Ethernet Layer 4" must be integrated in the project.
Procedure
1. Select the channel unit and open dialog window "System parameters" with the context
menu.
2. Select the "Transport parameter" tab.
3. Set the value for "PDU size" to the value that was configured on the CP 1434 TF.
4. Define how often a connection establishment should be attempted in the "Setup attempt"
filed.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
315
SIMATIC TI Ethernet Layer 4
13.3 Configuring the Channel
5. Select "Infinite" in the "Duration of Send Repetitions" area.
6. Enter value 30 in the "Acknowledgement time" field so that you are informed of the tag
status after 30 seconds at the most, if the communication partner has not responded within
this time (e.g. AS in "Stop" status).
316
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Serial
14.1
14
WinCC channel "SIMATIC TI Serial"
Introduction
The communication driver "SIMATIC TI Serial" is used for establishing a serial link between
WinCC station and an SIMATIC TI505 automation device.
This chapter describes
● how to configure the data transfer with the "SIMATIC TI Serial" channel.
● how to configure a connection and a tag.
Channel units
The communication driver has one channel unit for controlling a COM port for the serial
connection.
The following capability is available:
● Channel unit "505 Serial Unit #1" for serial communication, either via the TBP protocol or
the NITP protocol.
Note
It is possible to run more than one logical connections (with different COM ports) through
one channel unit.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
317
SIMATIC TI Serial
14.2 Data type of the tags
14.2
Data type of the tags
Introduction
Define the required tags for a logical connection. From the WinCC viewpoint, you can access
the following data types:
● Binary tag
● Unsigned 8 bit value (is only supported by VMS addressing)
● Signed 8 bit value (is only supported by VMS addressing)
● Unsigned 16-bit value
● Signed 16-bit value
● Unsigned 32-bit value
● Signed 32-bit value
● Floating-point number 32-bit IEEE 754
● Raw data type
318
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Serial
14.3 Configuring the Channel
14.3
Configuring the Channel
14.3.1
Configuring the "SIMATIC TI Serial" channel
Introduction
The following steps are required for configuring the channel "SIMATIC TI Serial".
14.3.2
How to configure the connection
Introduction
The process connection using a serial connection is possible with the SIMATIC TI505
automation system. The serial interface on the CPU module is used in the automation system.
No additional communication module is required in WinCC. Communication can take place by
means of the default COM ports available on the system.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
319
SIMATIC TI Serial
14.3 Configuring the Channel
Procedure
1. Select the connection and open the "Connection properties" dialog window with menu point
"Properties" in the context menu.
2. Click on the "Properties" button. The "Connection properties" dialog is opened.
3. Select the communications interface (e.g. COM1, COM2 or a configured port) for the serial
link in the "Serial port" field.
4. Select the field "Detect automatically" when the data transfer speed and the protocol used
by the PLC are required to be detected automatically by the channel unit.
5. Set the data transfer rate and the protocol being used in the fields "Baudrate" and "Protocol".
6. By selecting the field "Optimized Requests," you can optimize data transfer to transfer
several tags with one request.
7. If you select the "Deactivate connection" field, the logical connection is deactivated. This
is often a good idea during commissioning to temporarily deactivate the connection.
320
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Serial
14.3 Configuring the Channel
14.3.3
Configuring the tags
14.3.3.1
Configuring the tags
Introduction
For a connection between WinCC and the PLC via channel "SIMATIC TI Serial", tags of
different data types can be created within WinCC. This is described in the following section.
14.3.3.2
How to configure the address of a tag
Introduction
The tag address is entered according to the address structure of the SIMATIC TI505.
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select the desired data type (e.g. Signed 16 bit value) from the "General" tab.
3. Click the "Select" button. If it is a "Binary" or "8-Bit" tag, the "Bit/Byte tag" dialog will now
open. Tick the corresponding check box "Access a Bit/Byte", if data should be written to
the AS memory.
4. Click the "Select" button. The "Address properties" dialog is opened.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
321
SIMATIC TI Serial
14.3 Configuring the Channel
5. Select the location of the tag in the automation system in the "Address type" field.
Depending the selected address type, more definitions have to be made (e.g. "V-tag
memory" for address type in the "Data Element Number" field).
6. In the field "Read-Only Tag", you can specify that the tag cannot be written by WinCC.
Note
Structure tags are supported in address areas V, K, X, Y and C.
A description of address types may be found in the SIMATIC TI505 Technical Documentation.
Write access to memory areas in the AS can only performed bit-wise or word-wise in channel
"TI Serial". When using binary and "8 Bit" tags, dialog "Bit-Byte-tag" is opened in addition to
dialog "Address properties" and this can be used to define write access to individual bits or
bytes. For this purpose, the addressed memory area is read from the AS for every single write
request and the corresponding bits and/or bytes are modified. Afterwards, the data is written
back to the AS's memory.
Depending on the type of tag, you can access the memory in the AS bit-wise or byte-wise.
14.3.3.3
How to configure a tag with bit-wise access
Introduction
Write access to memory areas in the AS can only performed bit-wise or byte-wise in channel
"SIMATIC TI Serial". When using binary and "8 Bit" tags, dialog "Bit-Byte-tag" is opened in
addition to dialog "Address properties" and this can be used to define write access to individual
bits or bytes. For this purpose, the addressed memory area is read from the AS for every single
write request and the corresponding bits and/or bytes are modified. Afterwards, the data is
written back to the AS's memory.
Note
Changes that have been made by the AS in a read data area are overwritten when writing
back into the data area.
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "binary tag" on the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
322
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMATIC TI Serial
14.3 Configuring the Channel
4. Check the "Access to a bit" checkbox and define the addressing for the bit.
5. Click the "Select" button. The "Address properties" dialog is opened.
6. Select the addressing type of the PLC memory in the selection field.
7. Select the number of bit to be changed in the selection field.
Note
With the S5, flags, inputs and outputs can be addressed by byte, data blocks (DB, DX) are
addressed by word.
14.3.3.4
How to Configure a Tag with Byte by Byte Access
Introduction
Write access to memory areas in the AS can only performed bit-wise or byte-wise in channel
"SIMATIC TI Serial". When using binary and "8 Bit" tags, dialog "Bit-Byte-tag" is opened in
addition to dialog "Address properties" and this can be used to define write access to individual
bits or bytes. For this purpose, the addressed memory area is read from the AS for every single
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
323
SIMATIC TI Serial
14.3 Configuring the Channel
write request and the corresponding bits and/or bytes are modified. Afterwards, the data is
written back to the AS's memory.
Note
Changes that have been made by the AS in a read data area are overwritten when writing
back into the data area.
Procedure
1. Select the tag and open dialog window "Properties" with the context menu.
2. Select data type "Unsigned 8 bit value" or "Signed 8 bit value" in the "General" tab.
3. Click the "Select" button. The "Bit-/Byte-tag" dialog is opened.
4. Check the "Access to a byte" checkbox and define the addressing for the byte.
5. Click the "Select" button. The "Address properties" dialog is opened.
6. Select the addressing type of the PLC memory in the selection field
7. Select the number of byte to be changed in the selection field.
324
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMOTION
15.1
15
WinCC channel "SIMOTION"
Introduction
The "SIMOTION" channel connects a WinCC station with a SIMOTION automation system.
The connection is established via Industrial Ethernet using the TCP/IP protocol.
SIMOTION is a system platform for automation and drive solutions with an emphasis on motion
control applications and technology tasks.
The SIMOTION modular system consists of the SIMOTION SCOUT Engineering System and
a common runtime system for various hardware platforms.
Export the project from SIMOTION SCOUT to access the data of a SIMOTION SCOUT project..
Then create a WinCC project from the exported files with the Simotion Mapper.
You can configure certain changes to the configuration of the SIMOTION automation system,
e.g. change an IP address, later in WinCC. Further changes must be configured in
SIMOTION SCOUT, exported again and transferred with the Simotion Mapper.
Note
You must be familiar with the SIMOTION SCOUT Engineering System and the configuration
of WinCC to configure the "SIMOTION" channel in WinCC.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
325
SIMOTION
15.2 Overview of the supported data types
15.2
Overview of the supported data types
Introduction
The data type and the format adaptation to the data format in the automation system are
determined in the configuration of a tag.
The table shows the data types supported by the channel and the application of format
adaptations.
Supported data types
326
Data Types
Type conversion
Binary tag
No
Signed 8-bit value
Yes
Unsigned 8-bit value
Yes
Signed 16-bit value
Yes
Unsigned 16-bit value
Yes
Signed 32-bit value
Yes
Unsigned 32-bit value
Yes
Floating-point number 32-bit IEEE 754
Yes
Text tag, 8-bit font
No
Raw data type
No
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMOTION
15.3 Configuring the channel
15.3
Configuring the channel
15.3.1
Configuration of the "SIMOTION" channel
Introduction
This chapter describes how to configure the "SIMOTION" channel.
Note
You must be familiar with the SIMOTION SCOUT Engineering System and the configuration
of WinCC to configure the "SIMOTION" channel.
Proceed as follows to configure the "SIMOTION" channel:
1. Export the SIMOTION SCOUT project from SIMOTION SCOUT.
2. Create WinCC project with the Simotion Mapper.
3. Open WinCC project.
4. Configure system parameters.
Further information about the diagnosis of the channel, the connection and the tags can be
found in the "Diagnosis 'SIMOTION' channel" chapter.
15.3.2
How to export a SIMOTION SCOUT project
Introduction
This section describes how to export tags and message definitions from SIMOTION SCOUT.
Requirements:
● You are familiar with the SIMOTION SCOUT Engineering System.
● You have access to the SIMOTION SCOUT project to be exported.
Procedure
1. Open the SIMOTION SCOUT project to be exported in SIMOTION SCOUT.
2. Select "Export OPC Data" under "Tools."
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
327
SIMOTION
15.3 Configuring the channel
3. Select version "SIMATIC NET V6.4", the desired scope and at least the "OPC-Alarm/Event"
option for the export.
Note
Simotion Mapper does not process other export versions than "SIMATIC NET V6.4".
4. Select the destination directory.
5. Select the communication interface.
The project is exported.
6. Enter the routing information if you are using routing.
The SIMOTION SCOUT project is exported. The "OPC_Data.sti" and "OPC_AE.xml" files are
saved in the destination directory.
15.3.3
How to create a WinCC project with Simotion Mapper
Introduction
This section describes how to create a WinCC project from the exported SIMOTION SCOUT
project with the Simotion Mapper.
Note
If a WinCC project was already created for an older version of the SIMOTION SCOUT project,
only the SIMOTION parameters are changed in a transmission. All other configuration
settings in the WinCC project (such as archiving) remain the same.
Requirements:
● You have access to the export files "OPC_Data.sti" and "OPC_AE.xml" of the
SIMOTION SCOUT project.
● You have access rights to the WinCC installation directory.
Note
In the SIMOTION SCOUT programming environment, the tags to be exported can be
filtered using the watch tables. Use the watch tables to keep the number of tags in the
WinCC project low. More information on the watch tables can be found in the SIMOTION
SCOUT online help.
Procedure
1. Launch the "SimotionMapper.exe" program in the WinCC installation directory.
2. Click "Open". Navigate to the directory with the files "OPC_Data.sti" and "OPC_AE.xml".
The data is read and displayed in Simotion Mapper.
328
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMOTION
15.3 Configuring the channel
3. In the Simotion Mapper Explorer, select the groups and tags you need in your WinCC
project.
4. Select "Create new WinCC project".
5. If you want to change the "WinCC connection name", click on the name displayed and enter
the new name.
6. Specify the "First TA message number" for the technological alarm. The value must be
selected in such a way that it does not lead to collisions with messages of other
communication channels. The default value is 100.
The Simotion Mapper creates one message and a total of six template messages for each
Simotion connection starting from the number specified.
7. Click "Start mapping". Select the destination folder for the WinCC project.
The WinCC project is created. The progress bar indicates the progress of the procedure.
8. Close Simotion Mapper.
The WinCC project is created and can now be opened and edited in WinCC.
Note
You may have to set the system parameters of the "SIMOTION" channel in WinCC to use
the created WinCC project.
15.3.4
How to change a WinCC project with Simotion Mapper
Introduction
This section describes how to add an exported SIMOTION SCOUT project to an existing
WinCC project with the Simotion Mapper. In this way, you can use the same Simotion project
several times in one WinCC project, for example.
Note
If a WinCC project was already created for an older version of the SIMOTION SCOUT project,
only the SIMOTION parameters are changed in a transmission. All other configuration
settings in the WinCC project (such as archiving) remain the same.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
329
SIMOTION
15.3 Configuring the channel
Requirements:
● You have access to the export files "OPC_Data.sti" and "OPC_AE.xml" of the
SIMOTION SCOUT project.
● You have access rights to the WinCC installation directory.
Note
In the SIMOTION SCOUT programming environment, the tags to be exported can be
filtered using the watch tables. Use the watch tables to limit the number of tags in the
WinCC project. More information on the watch tables can be found in the SIMOTION
SCOUT online help.
Procedure
1. Open the WinCC project to be edited.
2. Launch the "SimotionMapper.exe" program in the WinCC installation directory.
3. Click "Open". Navigate to the directory with the files "OPC_Data.sti" and "OPC_AE.xml".
The data is read and displayed in Simotion Mapper.
4. In the Simotion Mapper Explorer, select the groups and tags you need in your WinCC
project.
5. Select "Add to the open project".
6. If you want to re-add a group or tag that has already been created, you must change the
"WinCC connection name" by clicking on the name displayed.
7. If you do not want to transfer any messages, groups or tags for a connection, unselect
"WinCC connection name".
8. Specify whether tags should be overwritten.
9. Specify the "First TA message number" for the technological alarm. The value must be
selected in such a way that it does not lead to collisions with messages of other
communication channels. The default value is 100.
The Simotion Mapper creates one message and a total of six template messages for each
Simotion connection starting from the number specified.
Note
Please do change any "First TA message number" that has already been mapped. If you
do, you may experience unpredictable message behavior.
10.Click "Start mapping". Select the destination folder for the WinCC project.
The SIMOTION SCOUT project is added to the open WinCC project. The progress bar
indicates the progress of the procedure.
11.Close Simotion Mapper.
The WinCC project was expanded by the SIMOTION SCOUT project and saved with your
settings.
330
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMOTION
15.3 Configuring the channel
15.3.5
How to change the connection parameters
Introduction
In this section, you will learn how to change the connection parameters of the SIMOTION
network address.
Note
Change only the connection parameters listed here. Do not create new connection for the
"SIMOTION" channel. Incorrectly set connections may result in control errors in the PLC.
Configure new connections according to the description in the chapter "Configuration of the
"SIMOTION" channel (Page 327)".
Requirements
● The SIMOTION communication driver is integrated in the WinCC project.
Procedure
1. Open the directory structure for the "SIMOTION" communication driver in the "Tag
Management" editor.
2. Select "Properties" in the shortcut menu of the channel unit.
3. Click "Properties" in the open dialog box.
The "Connection Properties - SIMOTION" dialog box opens.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
331
SIMOTION
15.3 Configuring the channel
4. Change the connection parameters for the SIMOTION network address in the respective
fields.
5. Close each open dialog box by clicking "OK."
15.3.6
How to change the tag address
Introduction
This chapter describes how to change a tag address in the "SIMOTION" channel.
Note
You must have very good knowledge of the use of ANY pointers to change the tag address
in the "SIMOTION" channel. No communication connection may be established if the tag
address is entered incorrectly.
Requirements
● The "SIMOTION" channel in integrated into the WinCC project.
● A connection with tags has been created in the "SIMOTION" channel unit.
Procedure
1. Click "Addressing" in the shortcut menu of the tag to be changed.
2. Change the tag address.
332
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMOTION
15.3 Configuring the channel
15.3.7
System parameter configuration
15.3.7.1
System Parameters of the Channel Unit
Introduction
If you require a different configuration than the WinCC default settings, make these settings
in the "System Parameters" dialog box.
You can change the following system parameters:
● Logical device name
● The channel uses cyclic read services in the AS
Logical device name
WinCC and the PLC communicate by means of logical device names that are assigned when
the communications processor is installed in the PLC.
The channel uses cyclic read services in the AS
The PLC cyclic read services group the tags that are to be read cyclically into individual
requests and transfer these to the PLC. The PLC sends the requested data the first time on
receipt of the request and then again each time the cycle time elapses.
When cyclic read services are enabled, you can use the change-driven transfer function. If the
PLC supports change-driven transfer, the data are then transferred only when values are
changed.
15.3.7.2
How to Configure the System Parameters
Introduction
This section shows how to configure the system parameters of the "SIMOTION" channel.
The "System Parameters" dialog comprises two tabs:
● "SIMOTION" tab
● "Unit" tab
Note
When the project is copied to another computer, the settings in the "Unit" tab are retained.
The settings on the "SIMOTION" tab are deleted on the other hand.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
333
SIMOTION
15.3 Configuring the channel
Requirements
● The "SIMOTION" channel in integrated into the WinCC project.
Procedure
1. Select the "SIMOTION" channel in the variable management. Open the "System
Parameters" dialog box in the shortcut menu of the "Simotion" channel unit.
2. Select the "SIMOTION" tab.
3. To enable cyclic reading of tags and change-driven transfer, select "by PLC" and "Changedriven transfer."
Note
The "cycle management", "lifebeat monitoring" and "stop monitoring" functions are not
supported by the integrated SINAMICS servo control. The "SIMOTION" channel therefore
ignores corresponding settings for connections to SINAMICS servo controls. The channel
determines whether the AS supports the respective function when establishing the
connection.
4. Select the "Lifebeat monitoring" function if required.
Determine the interval in seconds for sending lifebeat monitoring messages.
Determine the monitoring time in seconds for monitoring the response to a lifebeat
monitoring message.
5. Enable "CPU Stop Monitoring" if you want WinCC to signal a fault in the communication
when the SIMOTION CPU is in the stopped state.
334
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMOTION
15.3 Configuring the channel
6. Select the "Unit" tab.
"S7ONLINE" is displayed as a default for "logical device name". You must change the
device name if a different name was selected when installing the used communications
processor.
7. To set the device name automatically at the start of runtime, select "Set automatically."
8. To give write jobs higher priority than read jobs during processing, select "Write with priority."
9. Close the dialog by clicking "OK."
Note
Setting changes only take effect after WinCC is restarted.
15.3.7.3
How to Change the Logical Device Name
Introduction
WinCC and SIMOTION communicate through logical device names. These logical device
names are assigned when the communications processor is installed.
Requirements
● The "SIMOTION" channel in integrated into the project.
● A connection has been created in the "SIMOTION" channel unit.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
335
SIMOTION
15.3 Configuring the channel
Procedure
1. Select the SIMOTION channel in Tag Management.
2. Open the "System Parameters" dialog box in the shortcut menu.
3. Select the "Unit" tab.
4. Enter the device name in the "Logical device name" field. You can select an entry from the
list or enter a new name.
The device names are determined by the "Set PG/PC interface" tool. You call the tool in
the system control. Only the currently set device name is displayed if it is not installed.
If you specify a different logical device name, a message is displayed.
Only enter a name if the communications processor being used on the target station is not
installed on the configuring system.
5. Close the dialog by clicking "OK."
Note
Setting changes only take effect after WinCC is restarted.
336
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMOTION
15.4 Diagnosis "SIMOTION" channel
15.4
Diagnosis "SIMOTION" channel
15.4.1
Diagnosis possibilities of the "SIMOTION" channel
The following possibilities exist for the diagnosis and error detection of the "SIMOTION"
channel and its tags.
Checking the Communication Processor Configuration
After checking the access point, the communication processor can be tested with the "Set PG/
PC interface" application. The communication processor can be checked under SIMATIC NET
in the same way.
Checking the Configuration of the Connection and Tags
There may be errors in the configuration of the system and connection parameters. An incorrect
tag addressing may also be responsible for wrong tag values.
Diagnosis of the Channel with "Channel Diagnosis"
You can query the status of the channel and the connection in runtime with "Channel
Diagnosis". Errors are displayed by "Error Codes".
Diagnosis of the Channel Tags
You can query the current value, the current quality code and the last change time of the tag
in runtime in the tag management.
15.4.2
Description of Log File Entries
Introduction
The channel enters important status changes and errors in the logfile. The entries support the
analysis of communication faults.
Every entry in the file contains a date and time stamp with the following flag names and
description.
Example of a logbook entry:
2009-10-28 12:10:11,467 INFO Log starting ...
2009-10-28 12:10:11,483 INFO | LogFileName : D:\SIEMENS\WINCC\Diagnosis
\Simotion_01.LOG
2009-10-28 12:10:11,483 INFO | LogFileCount : 3
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
337
SIMOTION
15.4 Diagnosis "SIMOTION" channel
2009-10-28 12:10:11,483 INFO | LogFileSize : 1400000
2009-10-28 12:10:11,483 INFO | TraceFlags : fa000000
2009-10-28 12:10:11,498 INFO SIMOTION channel DLL started!
2009-10-28 12:10:11,498 INFO SIMOTION channel with own cycle creation!
2009-10-28 12:10:11,967 INFO Connection "D445": StartRegisterEvVariable for
dwVariableCount = 89
2009-10-28 12:10:11,967 INFO Connection "D445": RegisterEvVariable for Variable
"@[email protected]"!
...
2009-10-28 12:10:11,983 INFO Connection "D445": EndRegisterEvVariable
2009-10-28 12:10:12,436 INFO S7DOS release: @(#)TIS-Block Library DLL Version R8.0.0.0REL-BASIS
2009-10-28 12:10:12,436 INFO S7DOS version: V8.0 / 0
2009-10-28 12:10:12,436 INFO SIMOTION version: V6.0 / Sep 15 2009 / 08:06:43
2009-10-28 12:10:12,436 INFO SIMOTION channel unit "Simotion" activated!
2009-10-28 12:10:12,451 ERROR Cannot connect to "SINAMICS_Integrated": Errorcode
0xFFDF 42C2!
2009-10-28 12:10:12,451 ERROR Cannot connect to "D445": Errorcode 0xFFDF 42C2!
Description of the Most Important Entries for the "INFO" Flag
338
Message text
Meaning
LogFileName : C:\ Siemens\ WinCC\
Diagnose\ "channel_name".LOG
Name of the log file with path
LogFileCount : "n"
Number of log files of the channel
LogFileSize : "x"
Size of the individual log files in bytes
TraceFlags : c4000000
Displays the flags used by the Trace function as a
hexadecimal number
SIMOTION channel DLL started!
Start message
SIMOTION channel DLL terminated!
End message
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
SIMOTION
15.4 Diagnosis "SIMOTION" channel
Description of the Most Important Entries for the "ERROR" Flag
Message text
Meaning
Cannot connect to <connectionname>:
Errorcode 0x0000 7<xxx>!
Communication error
Communication to SIMOTION could not be established
immediately after activating WinCC.
<connectionname> = Name of connection
<xxx> 1...fff
The channel has received all other error codes as the result
of a function call of S7DOS, a lower layer or from the AS.
Connectionerror <nnn>
<connectionname>:
Errorcode 0x0000 7xxx!
Communication error
Communication to SIMOTION could not be established after
activating WinCC. The connection was broken.
<nnn> = Number of connection terminations for this
connection
<connectionname> = Name of connection
<xxx> 1...fff
The channel has received all other error codes as the result
of a function call of S7DOS, a lower layer or from the AS.
Channel API error: errorstring
Channel API error
The channel passed the error string 'errorstring' to WinCC
Explorer. The error string is displayed in an information box
depending on the error relevance. See API error texts for a
description of the error strings.
Max. count of API errors reached - API
logbook deactivated
Channel API error
Depending on the error and function, errors can occur
cyclically on the API. To avoid filling the logbook file with
these error messages, a maximum of 32 messages are
output for an API error.
Cannot write storage data!
Cannot read storage data / use default
data
Storage data illegal or destroyed / use
default data!
No storage data / use default data!
General Channel Error Messages
Devicename in unit "unitname" changed
from "old devicename" to "new
devicename"
Initialization message
Note
The error codes of the "SIMOTION" channel correspond to those of the "SIMATIC S7 Protocol
Suite" channel. You will find the description of the error code in the "Error codes for connection
fault" chapter in the help for the "SIMATIC S7 Protocol Suite" channel.
In addition, SIMOTION reports the error code 0x000 7301 if the consistency check failed.
The reason for the error message is that the data exported from SIMOTION SCOUT for the
AS entered checksum do not match the checksum in the connected device.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
339
System Info
16.1
16
"System Info" Channel
Contents
The "System Info" channel is used to evaluate system information such as the time, date, disk
capacity and provides functions such as timers and counters.
This chapter will show you
● configure the channel, connection and tags
● display system information in a process picture
● use system information to trigger and display a message
● display system information graphically
● display the system information from several servers in a multi-user system
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
341
System Info
16.2 WinCC System Info Channel
16.2
WinCC System Info Channel
Principle
The System Info channel is used to evaluate system information such as the time, date, disk
capacity and provides functions such as timers and counters.
Possible applications are:
● Display of the time, date and day of the week in process pictures
● Triggering of events through evaluation of system information in scripts
● Display of the CPU load in a trend
● Display and monitoring of the available drive space on different servers of a client system
● Monitoring of the available disk capacity and triggering of a message
The channel requires no hardware, since it directly accesses the system information of the
computer on which it has been installed. In order for the channel to function, a connection must
be set up. Additional connections are possible, but not required for the proper operation.
For more information regarding the diagnosis of channels and tags, refer to "Communication
Diagnostics".
Note
The process tags required for the System Info channel need no licenses. Thus, the tags are
not entered in the license count.
If you have no administrator rights under Windows 2003 Server, you must be a member of
the superusers of the "System Monitor User" group in order to use the System Info channel.
Communication Manual
The communication manual contains additional information and extensive examples for the
channel configuration. This manual is available for download on the Internet:
● http://support.automation.siemens.com/
Search by order number:
342
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.2 WinCC System Info Channel
● A5E00391327
See also
Use in Multi-User and Client Systems (Page 363)
How To Call Up and Evaluate System Information (Page 351)
How to Configure the System Info Channel (Page 350)
Differences to Other Software Components (Page 349)
Overview of the Supported System Information (Page 344)
Diagnosis of Channels and Tags (Page 369)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
343
System Info
16.3 Overview of the Supported System Information
16.3
Overview of the Supported System Information
Introduction
In the "Function" field in the "System Info" dialog, you can specify the system information to
be assigned to a WinCC tag. The display format is set in the "Format" field.
System Info Channel Supported System Information - Overview
344
Function
Data type
Format
Preview
Date
Text tag
8-bit character set
DD.MM.YYYY
21.10.1999
DD.MM.YY
21.10.99
MM-DD-YYYY
10-21-1999
MM-DD-YY
10-21-99
MM/DD/YY
10/21/99
Day
Unsigned
16-bit value
DD
1...31
Month
Unsigned
16-bit value
MM
1...12
Year
Unsigned
16-bit value
YYYY
2000
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.3 Overview of the Supported System Information
Function
Data type
Format
Preview
Weekday
Unsigned
16-bit value
Text: 1 for
Monday to
7 for Sunday
1...7
Text: Mon,Tue,Wed,
Thu,Fri,Sat,Sun
Mon ... Sun
HH:MM:SS
HH:MM
HH:MM AM,PM
23:45:37
23:45
23:45 PM
Text tag
8-bit character set
Time
Text tag
8-bit character set;
length = 10 bytes
Length = 12 bytes
HH:MM:SS AM,PM
23:45:37 PM
Hour
Unsigned
16-bit value
HH
0...23
Minute
Unsigned
16-bit value
MM
0...59
Second
Unsigned
16-bit value
SS
0...59
Milliseconds
Unsigned
16-bit value
MSC
0...999
Counter
Signed
32-bit value
ZZZZ
0...9999
CPU load
Floating-point number
32-bit IEEE 754
Total load in %
idle load in %
process load in %
0...100%
Timer
Signed
32-bit value
TTTT
0...9999
Free main memory
Floating-point number
32-bit IEEE 754
Free capacity in kB
Free in %
Free in bytes
0...n kB
0...100%
0...n B
Free
disk capacity
(local disks)
Floating-point number
32-bit IEEE 754
Free in MB
Free in %
0...n MB
0...100%
Printer monitoring
Unsigned
32-bit value
Filled capacity of
spooler disk
Printer status
Job status
Free spooler disk
area in kB
Free PRT_OUTDisk areas in kB
Size of
spooler directory in kB
Size of PRT_OUT directory in kB
0...n %
Used in kB
Used in %
Available in kB
0...n kB
0...100%
0...n kB
Status of
swap file
Floating-point number
32-bit IEEE 754
0...n
0...n
0...n kB
0...n kB
0...n kB
0...n kB
Counter
This function is useable for test purposes in scripts.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
345
System Info
16.3 Overview of the Supported System Information
Timer
When this function is selected, the "System Info" dialog is extended with fields "Limits from"
and "to".
After every second, the timer is incremented or decremented. The direction in which the
changes are made is determined by the starting and ending values in the fields "Limits from"
and "to". If the start value is smaller than the end value, the timer is incremented. If the start
value is greater than the end value, the timer is decremented.
If in Runtime, a value is entered in the I/O field linked to the timer, the start and current timer
values is set to this value. Example: timer configured from 0 to 60. If "0" is written in Runtime,
the timer is reset.
After the deactivation, the original start value is reapplied.
CPU load
For the formats "Total load in %" and "Idle load in %" in connection with multiprocessor PCs
enter the CPU number beginning with "0".
For the format "Process load in %" enter the instance number, if there are several instances
of a process.
Free disk capacity
The system can only determine the space available on a local hard disk or diskette.
Printer monitoring
With the "Printer status" and "Job status" formats the server name must be entered in the
"Printer" field. The printers in use must support this status information to be able to use this
system information.
In order to analyze the printer status, please observe the following:
● The port monitor is responsible for the transmission of the printer status to the spooler.
Depending on the selected printer port, different port monitor DLLs are installed. From the
port monitors supplied with Windows, only "TCPMON.DLL" is capable of transmitting the
printer status using the TCP/IP port. "LOCALMON.DLL" using the LPT port does not
communicate the printer status.
● The printer status is assessed only after a print job has been submitted, but not during
polling of the status at the port.
In the case of the "Free PRT_OUT drive space" and "PRT_OUT Directory Size" formats, the
channel automatically determines the path for the "Directory" field.
Error codes for the "Printer status" format
346
Status
Error code
PRINTER_STATUS_PAUSED
0x00000001
PRINTER_STATUS_ERROR
0x00000002
PRINTER_STATUS_PENDING_DELETION
0x00000004
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.3 Overview of the Supported System Information
Status
Error code
PRINTER_STATUS_PAPER_JAM
0x00000008
PRINTER_STATUS_PAPER_OUT
0x00000010
PRINTER_STATUS_MANUAL_FEED
0x00000020
PRINTER_STATUS_PAPER_PROBLEM
0x00000040
PRINTER_STATUS_OFFLINE
0x00000080
PRINTER_STATUS_IO_ACTIVE
0x00000100
PRINTER_STATUS_BUSY
0x00000200
PRINTER_STATUS_PRINTING
0x00000400
PRINTER_STATUS_OUTPUT_BIN_FULL
0x00000800
PRINTER_STATUS_NOT_AVAILABLE
0x00001000
PRINTER_STATUS_WAITING
0x00002000
PRINTER_STATUS_PROCESSING
0x00004000
PRINTER_STATUS_INITIALIZING
0x00008000
PRINTER_STATUS_WARMING_UP
0x00010000
PRINTER_STATUS_TONER_LOW
0x00020000
PRINTER_STATUS_NO_TONER
0x00040000
PRINTER_STATUS_PAGE_PUNT
0x00080000
PRINTER_STATUS_USER_INTERVENTION
0x00100000
PRINTER_STATUS_OUT_OF_MEMORY
0x00200000
PRINTER_STATUS_DOOR_OPEN
0x00400000
PRINTER_STATUS_SERVER_UNKNOWN
0x00800000
PRINTER_STATUS_POWER_SAVE
0x01000000
Error codes for the "Job status" format
Status
Error code
JOB_STATUS_PAUSED
0x00000001
JOB_STATUS_ERROR
0x00000002
JOB_STATUS_DELETING
0x00000004
JOB_STATUS_SPOOLING
0x00000008
JOB_STATUS_PRINTING
0x00000010
JOB_STATUS_OFFLINE
0x00000020
JOB_STATUS_PAPEROUT
0x00000040
JOB_STATUS_PRINTED
0x00000080
JOB_STATUS_DELETED
0x00000100
JOB_STATUS_BLOCKED_DEVQ
0x00000200
JOB_STATUS_USER_INTERVENTION
0x00000400
JOB_STATUS_RESTART
0x00000800
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
347
System Info
16.3 Overview of the Supported System Information
Note
The error codes of the "Printer status" and "Job status" formats corresponds to the values in
the Visual C-referenced file "Winspool.h" .
348
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.4 Differences to Other Software Components
16.4
Differences to Other Software Components
Introduction
Some of the System Info channel system information can also be evaluated or displayed by
WinCC using ActiveX controls.
Once fundamental difference to ActiveX controls can be seen in the fact that the System Info
channel system information is assigned to a WinCC tag. The continued evaluation (e.g. of
messages, limit values) can be carried out repeatedly and is then configured individually. The
ActiveX controls are intended for use in the specified applications and may also be used for
multi-user or client systems.
For the following system information, differences between the ActiveX control and the channel
exist:
Time
The ActiveX control "WinCC Digital/Analog Clock Control" is used to display the time in WinCC.
This control also supports an analog display of the time. The control does not require the
System Info channel even when if it is used in the process control system options. Using the
control, it is possible to display a WinCC client's time in its process picture. This is not possible
with the System Info channel, since this always displays the server's system time.
Free disk capacity
The ActiveX control "IX Diskspace" is supplied to display the disk space available in WinCC.
This ActiveX control can also display the space available on network drives and supports other
configuration options such as the setting of multiple limit values directly in the control.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
349
System Info
16.5 Configuring the Channel
16.5
Configuring the Channel
16.5.1
How to Configure the System Info Channel
Introduction
This section illustrates how to configure the System Info channel.
Procedure
1. Select the entry "Add New Driver" in the shortcut menu of Tag Management. A selection
dialog is opened.
2. Select the "System Info.chn" channel and close the dialog. The channel is set up and the
channel driver is displayed in Tag Management.
3. Select the associated System Info channel unit and call up the shortcut menu. In this
shortcut menu, select "New Connection".
4. In the "Connection Properties" dialog, enter the connection name. Close the dialog.
5. Choose the "New Tag" option from the shortcut menu for the connection. A dialog is opened.
6. Enter the tag name and set its data type.
If you want to use the example for this channel, close the dialog and continue with the topic
"How to Configure a Tag".
7. Click the "Select" button to open the "System Info" dialog. Select the desired function and
format. The associated type of the WinCC tag is displayed in the "Data Type" field.
8. Close the open dialogs.
350
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.6 Examples of Evaluating and Displaying System Information
16.6
Examples of Evaluating and Displaying System Information
16.6.1
How To Call Up and Evaluate System Information
This section uses examples to illustrate how system information can be displayed and
evaluated in a variety of ways.
See also
How to Display the Printer Status in a Status Display (Page 359)
How to Configure a Message Regarding Free Disk Capacity (Page 356)
How to Display the CPU Load in a Trend Window (Page 355)
How to Display the Free Disk Capacity in a Bar Graph (Page 354)
How to Display the Time in an I/O Field (Page 352)
How to Configure a Tag in the System Info Channel (Page 351)
16.6.2
How to Configure a Tag in the System Info Channel
Introduction
This section illustrates how to configure tags in the System Info channel. These tags are used
in the examples.
Requirement
Install the "SystemInfo.chn" channel.
Table of the Data Types Used
The table below shows the tag types and formats used in the System Info channel.
Example
System Information
Tag name
Data type
Format
I/O field
Time
Sysinfo_Time
Text tag
8-bit character set
Hours: minutes:
seconds
(HH:MM:SS)
Bar,
message
Free disk
capacity
(disk: C)
Sysinfo_Drive_C
Floating-point
number
32-bit IEEE 754
0-100%
(free in %)
Trends
CPU load
Sysinfo_CPU
Floating-point
number
32-bit IEEE 754
0-100%
(total load in %)
Printer
status
Printer monitoring
Sysinfo_Printerst
ate
Unsigned 32-bit
value
0-n (hex)
(printer status)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
351
System Info
16.6 Examples of Evaluating and Displaying System Information
Procedure
1. In the shortcut menu of the associated System Info channel unit, select the entry "New
Connection" and create a connection named "Testinfo".
2. Choose the "New Tag" option from the shortcut menu for the connection.
3. In the "Tag Properties" dialog, enter the tag name. For the example, take the appropriate
tag name from the table of data types used and enter it in the "Name" field. In the "Data
Type" field, set the tag's data type in accordance with the table.
4. Click the "Select" button to open the "System Info" dialog. Set the system information and
display format in accordance with the information in the table.
5. Close all open dialogs.
See also
How to Configure a Message Regarding Free Disk Capacity (Page 356)
How to Configure the System Info Channel (Page 350)
How to Display the Printer Status in a Status Display (Page 359)
How to Display the CPU Load in a Trend Window (Page 355)
How to Display the Free Disk Capacity in a Bar Graph (Page 354)
How to Display the Time in an I/O Field (Page 352)
16.6.3
How to Display the Time in an I/O Field
Requirements
Configure a "Sysinfo_Time" tag with data type "Text tag 8-bit character set". This tag must be
assigned the "Time" system information with display format "HH:MM:SS".
352
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.6 Examples of Evaluating and Displaying System Information
Procedure
1. Start Graphics Designer and open a picture.
2. Add an I/O field to the picture. Select the "I/O field" object from the object list under "Smart
Objects". The "I/O Field Configuration" dialog is opened.
3. In the "Tag" field, enter the name "Sysinfo_Time".
4. Set the update to "1 s".
5. Set the field type to "Output". Close the dialog.
6. Click "Properties" in the I/O field's shortcut menu to open the "Object Properties" dialog.
7. On the "Properties" tab, select "Output/Input". Set the "Data Format" attribute to "String".
8. Close the dialog and save the picture.
9. Click the appropriate button in the Graphics Designer toolbar to activate Runtime.
Note
The update cycle should be chosen with careful consideration, as it affects the load on the
computer. Therefore, updating a time display every 250 ms is detrimental to the system
performance.
See also
How to Start Runtime (Page 362)
How to Insert an I/O Field (Page 362)
How to Configure a Tag in the System Info Channel (Page 351)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
353
System Info
16.6 Examples of Evaluating and Displaying System Information
16.6.4
How to Display the Free Disk Capacity in a Bar Graph
Requirements
Configure a tag "Sysinfo_Drive_C" with data type "Floating-point number 32-bit IEEE754". This
tag must be assigned the "Free Disk Space" system information for drive "C" with display
format "Free capacity in %".
Procedure
1. Start Graphics Designer and open a picture.
2. Insert a bar graph into the picture. For this purpose, select the object "Bar" from "Smart
Objects" in the object palette. The "Bar Configuration" dialog is opened.
3. In the "Tag" field, enter the name "Sysinfo_Drive_C".
4. Set the update to "5 s".
5. Set the maximum value to "100" and the minimum value to "0". Close the dialog.
6. Click on "Properties" in the bar graph shortcut menu to open the "Object Properties" dialog.
7. On the "Properties" tab, select "Axis". Set the attribute "Decimal Places" to "0".
8. Close the dialog and save the picture.
9. Click the appropriate button in the Graphics Designer toolbar to activate Runtime.
Note
The update cycle should be chosen with careful consideration, as it affects the load on the
computer. Therefore, updating an available drive space display every second is detrimental
to the system performance.
354
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.6 Examples of Evaluating and Displaying System Information
See also
How to Start Runtime (Page 362)
How to Insert a Bar Graph (Page 361)
How to Configure a Tag in the System Info Channel (Page 351)
16.6.5
How to Display the CPU Load in a Trend Window
Requirements
Configure a tag named "Sysinfo_CPU" with data type "Floating-point number 32-bit IEEE754".
This tag must be assigned the "CPU Load" system information with display format "Total load
in %".
Procedure
1. Start Graphics Designer and open a picture.
2. Insert a trend display into the picture. You can accomplish this by selecting the "WinCC
Online Trend Control" object from the "Controls" object palette. The "Properties of WinCC
Online Trend Control" dialog is opened.
3. On the "General" tab, enter the name "Trend1" in the "Window Title" field.
4. In the "Data Source" field, select "Online Tags".
5. Click the "Trends" tab and then the "Selection" button to open the "Tag Configuration" dialog.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
355
System Info
16.6 Examples of Evaluating and Displaying System Information
6. Enter "Sysinfo_CPU" as the name of the tag and then select a cycle time of "2 s". Close
the dialog.
7. Close the "Properties of WinCC Online Trend Control" dialog and save the picture.
8. Click the appropriate button in the Graphics Designer toolbar to activate Runtime.
Note
The update cycle should be chosen with careful consideration, as it affects the load on the
computer. Therefore, updating a CPU load display every 500 ms is detrimental to the system
performance.
See also
How to Start Runtime (Page 362)
How to Configure a Tag in the System Info Channel (Page 351)
16.6.6
How to Configure a Message Regarding Free Disk Capacity
Requirements
Configure a tag "Sysinfo_Drive_C" with data type "Floating-point number 32-bit IEEE754". This
tag must be assigned the "Free Disk Space" system information for drive "C" with display
format "Free capacity in %".
Procedure
1. Start Alarm Logging and create a new message by adding a new line in the table window
below.
2. Open the "Single Message" dialog by clicking on "Properties" in the shortcut menu for the
new message.
356
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.6 Examples of Evaluating and Displaying System Information
3. Click the "Text" tab and then enter the text "Memory Space" in the "Message Text" field,
and the text "Hard Disk" in the "Point of Error" field. Close the dialog.
4. Select the "Extras / Add Ins" menu item to open the "Add Ins" dialog. If necessary, select
the "Analog Alarm" check box. Close the dialog.
5. Select "Analog Alarm" in the navigation window for Alarm Logging and then click on "New"
in the shortcut menu to open the "Properties" dialog. In the "Tag to be Monitored" field,
enter the name "Sysinfo_Drive_C".
6. Select the "One message for all limit values" check box. In the "Message Number" field,
enter the number of the newly created message. Close the dialog.
7. Select "Analog Alarm" in the navigation window. Select the entry "Sysinfo_Drive_C" in the
data window. Click "New" in the shortcut menu to open the "Properties" dialog. Click the
radio button "Lower Limit" and enter the value "30" in the "Limit value or tag" field.
8. Close the dialog. Save and exit Alarm Logging.
See also
How to Configure a Tag in the System Info Channel (Page 351)
How to Display a Message regarding the Available Disk Capacity (Page 358)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
357
System Info
16.6 Examples of Evaluating and Displaying System Information
16.6.7
How to Display a Message regarding the Available Disk Capacity
Requirements
● A tag "Sysinfo_Drive_C" with data type "Floating-point number 32-bit IEEE754". The tag
must be assigned the "Free Disk Space" system information for drive "C" with the display
format "Free mem in %".
● A message text and the lower limit value for the limit value monitoring of this tag.
● "Alarm Logging Runtime" must be set in the computer's startup parameters.
Procedure
1. Start Graphics Designer and open a picture.
2. Insert a message window into the picture. Select the "WinCC Alarm Control" object from
the "Controls" object palette and place it in the picture.
Close the quick configuration dialog without making any further changes.
3. Double-click the inserted control to open the "WinCC Alarm Control Properties" dialog.
4. Select the "User Text Blocks" entry from the "Type" field on the "Message Blocks" tab.
Under "Selection", select the check boxes "Message Text" and "Point of Error".
358
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.6 Examples of Evaluating and Displaying System Information
5. Click the "Message Line" tab. In the "Available Message Blocks" field, mark the entries
"Message Text" and "Point of Error" and then click the "Right Arrow" button to transfer them
to the "Elements of message line" field. Close the dialog.
6. Save the picture.
7. Click the appropriate button in the Graphics Designer toolbar to activate Runtime.
See also
How to Check the WinCC Startup Parameters (Page 361)
How to Start Runtime (Page 362)
How to Configure a Tag in the System Info Channel (Page 351)
16.6.8
How to Display the Printer Status in a Status Display
Introduction
This example shows a possible evaluation of the "Printer monitoring" system information based
on the "Printer status" display format. The printer or job status could also be evaluated by
configuring messages that are triggered by single bits in the printer or job status.
Requirements
● Configure a "Sysinfo_Printerstate" tag with data type "Unsigned 32-bit value". This tag must
be assigned to the "Printer monitoring" system information with the "Printer status" display
format.
● The printers in use must support these status displays to be able to use this system
information.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
359
System Info
16.6 Examples of Evaluating and Displaying System Information
Procedure
1. Start Graphics Designer and open a picture.
2. Insert a status display into the picture. Select the "Status display" object from the object
palette under "Smart Objects". The "Status Display Configuration" dialog is opened.
3. In the "Tag" field, enter the name "Sysinfo_Printerstate".
4. Set the update to "1 s".
5. Select the value "0" in the "Status" column. Assign this status an icon from the "Picture
Selection" area which, for example, represents a printer. Select the desired icon, drag it to
the "0" line with the mouse and drop it in the "Basic Picture" column. If no picture or a picture
other than the desired picture is shown in the "Picture Selection" area, a selection dialog
can be opened by clicking the "Browse..." button.
6. If you wish you can add additional bit positions with the "Add" button and assign another
picture to these statuses.
7. Close the dialog and save the picture.
8. Click the appropriate button in the Graphics Designer toolbar to activate Runtime.
360
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.6 Examples of Evaluating and Displaying System Information
In Runtime, a printer ready for use is displayed with the icon assigned the status "0" in step 5.
No picture is shown if there is an error in the printer or if you have not run step 6. If you assigned
icons to the other bit positions in step 6, they are shown accordingly.
Note
The update cycle should be chosen with careful consideration, as it affects the load on the
computer. Therefore, updating a time display every 250 ms is detrimental to the system
performance.
See also
How to Configure a Tag in the System Info Channel (Page 351)
How to Start Runtime (Page 362)
16.6.9
How to Check the WinCC Startup Parameters
Procedure
1. In WinCC Explorer, select "Computer".
2. Open the shortcut menu and select "Properties".
3. The "Computer List Properties" dialog is opened. Click the "Properties" button.
4. The "Computer Properties" dialog is opened.
5. Click the "Startup" tab and check the entries. If necessary, activate or deactivate Runtime
modules or add other applications to the startup list.
6. Close the open dialogs.
16.6.10
How to Insert a Bar Graph
Procedure
1. Start Graphics Designer and open a picture.
2. In the "Standard" object palette under "Smart Objects", select the object "Bar".
3. Insert a bar graph into the picture. To do this, point the mouse on the location in the working
area where you want the bar graph to be placed. While keeping the mouse button pressed,
drag the object to the desired size.
4. After you release the mouse button, the "Bar Configuration" dialog is opened. In this dialog,
enter the name of a WinCC tag and set the update specifications and limit. Additionally,
you can use the "Bar Direction" to set the orientation of the displayed bar.
5. Close the dialog.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
361
System Info
16.6 Examples of Evaluating and Displaying System Information
16.6.11
How to Insert an I/O Field
Procedure
1. Start Graphics Designer and open a picture.
2. In the "Standard" object palette under "Smart Objects", select the object "I/O Field".
3. Insert the I/O field into the picture. To do this, position the mouse on the location in the
working area where you want the I/O field to be placed. While keeping the mouse button
pressed, drag the object to the desired size.
4. After you release the mouse button, the "I/O Field Configuration" dialog is opened. In this
dialog, enter the name of a WinCC tag and set the update and field type settings.
Additionally, you can also select the "Font" to be used to display the value.
5. Close the dialog.
16.6.12
How to Start Runtime
Requirements
A startup picture must be defined before Runtime is activated.
Procedure
1. Save and close all files that may be open in an editor.
2. Select WinCC Explorer.
3. Activate the project by clicking the "Activate" button in the toolbar or by selecting "Activate"
in the "File" menu.
362
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.7 Special Functions
16.7
Special Functions
16.7.1
Use in Multi-User and Client Systems
16.7.1.1
Use in Multi-User and Client Systems
Introduction
In multi-user and client systems, the System Info channel can be used to process the system
information from a server on a client system. In a client system, it is thus possible for a single
WinCC client to monitor several servers.
See also
Monitoring the system information of several servers on a WinCC client (Page 363)
16.7.2
Example of monitoring system information from multiple servers
16.7.2.1
Monitoring the system information of several servers on a WinCC client
Introduction
In this example, two servers are monitored by a single WinCC client. The monitored system
information such as available disk space and CPU load is displayed in a process picture on
the WinCC client.
This requires the following configurations:
Configuration of first server
Configuration of second server
Import of tags on the WinCC client
Configuration of the process picture on the WinCC client
Activation of the project
Requirements
The server and the WinCC client must be connected through a Windows network.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
363
System Info
16.7 Special Functions
See also
How to Activate the Project (Page 368)
How to Configure the Process Picture on the WinCC Client (Page 367)
How to Import the Tags to the WinCC Client (Page 366)
How to Configure the Second Server (Page 365)
How to Configure the First Server (Page 364)
16.7.2.2
How to Configure the First Server
Introduction
This section presents the configuration of the first server, which is necessary for this example.
1. Configure the tags of the System Info channel to display available disk space and CPU
load.
2. Generation of a package
Table of the Data Types Used
The tag names and formats used in this "System Info" channel example are listed in the
following table.
Tag
Function
Data type
Format
Sysvar_1_Drive_
C
Free disk
capacity
Floating-point number
32-bit IEEE 754
0-100% (free in %)
Sysvar_1_CPU
CPU load
Floating-point number
32-bit IEEE 754
0-100% (total load in %)
Procedure
1. Create a multi-user project named "Testinfo_1" on the first server. Install the driver "System
Info.chn" in the project.
2. In the shortcut menu of the associated "System Info" channel unit, select the entry "New
Connection" and create a connection named "Connection1".
3. In the connection's shortcut menu, select "New Tag".
4. In the "Tag Properties" dialog, enter "Sysvar_1_Drive_C" as the name of the tag. Set the
"Data Type" to "Floating-point number 32-bit IEEE 754".
5. Click the "Select" button to open the "System Info" dialog. Set the "Function" field to "Free
Disk Space", the "Drive" to "C" and "Format" to "Free capacity in %". Close all open dialogs.
6. In the connection's shortcut menu, select "New Tag".
7. In the "Tag Properties" dialog, enter "Sysvar_1_CPU" as the name of the tag. Set the "Data
Type" to "Floating-point number 32-bit IEEE 754".
364
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.7 Special Functions
8. Click the "Select" button to open the "System Info" dialog. Set the value in the "Function"
field to "CPU Load" and the value in "Format" to "Total load in %". Close all open dialogs.
9. Create a package. Proceed by selecting "Server data" in the navigation window and
opening the shortcut menu. Select the menu item "Create". Acknowledge the message
stating that the package was created.
See also
How to Configure the Second Server (Page 365)
16.7.2.3
How to Configure the Second Server
Introduction
This section presents the configuration of the second server, which is necessary for this
example.
1. Configure the tags of the System Info channel to display available disk space and CPU
load.
2. Generation of a package.
Table of the Data Types Used
The tag names and formats used in this "System Info" channel example are listed in the
following table.
Tag
Function
Data type
Format
Sysvar_2_Drive_
C
Free disk
capacity
Floating-point number
32-bit IEEE 754
0-100% (free in %)
Sysvar_2_CPU
CPU load
Floating-point number
32-bit IEEE 754
0-100% (total load in %)
Procedure
1. Create a multi-user project named "Testinfo_2" on the second server. Install the driver
"System Info.chn" in the project.
2. In the shortcut menu for the associated "System Info" channel unit, select the entry "New
Connection" and create a connection named "Connection2".
3. In the connection's shortcut menu, select "New Tag".
4. In the "Tag Properties" dialog, enter "Sysvar_2_Drive_C" as the name of the tag. Set the
"Data Type" to "Floating-point number 32-bit IEEE 754".
5. Click the "Select" button to open the "System Info" dialog. Set the "Function" field to "Free
Disk Space", the "Drive" to "C" and "Format" to "Free capacity in %". Close all open dialogs.
6. In the connection shortcut menu, select "New Tag".
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
365
System Info
16.7 Special Functions
7. In the "Tag Properties" dialog, enter "Sysvar_2_CPU" as the name of the tag. Set the "Data
Type" to "Floating-point number 32-bit IEEE 754".
8. Click the "Select" button to open the "System Info" dialog. Set the value in the "Function"
field to "CPU Load" and the value in "Format" to "Total load in %". Close all open dialogs.
9. Create a package. Proceed by selecting "Server data" in the navigation window and
opening the shortcut menu. Select the menu item "Create". Acknowledge the message
stating that the package was created.
See also
How to Import the Tags to the WinCC Client (Page 366)
16.7.2.4
How to Import the Tags to the WinCC Client
Introduction
This section presents the configuration of the WinCC client, which is necessary for this
example.
1. Loading the package of the first sever project.
2. Loading the package of the second sever project.
Requirements
This example requires the use of two server project packages.
Server
Project
Package
1
Testinfo_1
Testinfo_1_<computer_name>
2
Testinfo_2
Testinfo_2_<computer_name>
Procedure
1. Create a client project named "mc_info" on the WinCC client.
2. In the server data shortcut menu, select "Load". The "Open" dialog is opened.
3. Select the computer on which the first server project "Testinfo_1" is located.
4. Select the package "Testinfo_1_<computer_name>.pck" in the "<project_name> \
<computer_name> \ Packages" directory.
5. Click the "Open" button and acknowledge the message after the package has opened.
6. Load the package "Testinfo_2_<computer_name>.pck" on the second server. For this
purpose, repeat steps 2 to 5 with the appropriate settings and names for the second project
from the "Requirements" table.
366
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
System Info
16.7 Special Functions
See also
How to Configure the Process Picture on the WinCC Client (Page 367)
16.7.2.5
How to Configure the Process Picture on the WinCC Client
Introduction
This section illustrates the configuration of the WinCC client, which is required in this example
to display the server system information in a process picture on a WinCC client.
1. Configuration of the system information display of the first server
2. Configuration of the system information display of the second server
Requirements
This example requires that the server project packages are loaded in the client project.
Package
Project
Tag
Testinfo_1_<computer_name>
Testinfo_1
Sysvar_1_Drive_C
Testinfo_1_<computer_name>
Testinfo_1
Sysvar_1_CPU
Testinfo_2_<computer_name>
Testinfo_2
Sysvar_2_Drive_C
Testinfo_2_<computer_name>
Testinfo_2
Sysvar_2_CPU
Procedure
1. On the WinCC client, start Graphics Designer and create a picture named "p_serverinfo".
2. Add an I/O field to the picture. Select the "I/O field" object from the object list under "Smart
Objects". The "I/O Field Configuration" dialog is opened.
3. Click the button for tag selection. The "Tags" dialog is opened.
4. Select the tag "Sysvar_1_Drive_C" of the first server project "Testinfo_1". For this purpose,
open the directory structure under the package "Testinfo_1_<computer_name>". Close the
dialog.
5. In the "I/O Field Configuration" dialog, set the update to "5 s".
6. Set the field type to "Output". Close the dialog.
7. Insert a second I/O field into the picture and configure it for the tag "Sysvar_1_CPU" of the
same project. For this purpose, repeat the steps 2 to 6 with the appropriate settings taken
from the "Requirements" table.
8. Repeat steps 2 to 7 to configure the tags of the second server project "Testinfo_2".
9. Close the dialogs and save the picture.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
367
System Info
16.7 Special Functions
Note
The update cycle should be chosen with careful consideration, as it affects the load on the
computer. Therefore, updating a date display every second is detrimental to the system
performance.
See also
How to Activate the Project (Page 368)
16.7.2.6
How to Activate the Project
Introduction
This section shows how to activate the projects on the servers and the WinCC client.
1. Create a startup picture in the server project "Testinfo_1" and activate the project.
2. Create a startup picture in the server project "Testinfo_2" and activate the project.
3. Define the startup picture in the project "mc_info" on the WinCC client and activate the
project.
Procedure
1. In the navigation window in the project "Testinfo_1" on server 1, select Graphics Designer
and use the shortcut menu to create a new picture.
2. Set this picture as the startup picture. To do this, select "Set as startup picture" from the
shortcut menu.
3. Click the "Activate" button in the toolbar to activate the project.
4. In the navigation window in the project "Testinfo_2" on server 2, select Graphics Designer
and use the shortcut menu to create a new picture.
5. Set this picture as the startup picture. To do this, select "Set as startup picture" from the
shortcut menu.
6. Click the "Activate" button in the toolbar to activate the project.
7. On the WinCC client in the navigation window in the project "mc_info", select Graphics
Designer. The process picture "p_serverinfo" is displayed in the data window.
8. Set this picture as the startup picture. To do this, select "Set as startup screen" from the
shortcut menu.
9. Click the "Activate" button in the toolbar to activate the project.
368
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.1
17
Diagnosis of Channels and Tags
This section describes the diagnosis of channels and their tags, as well as of internal tags.
This diagnosis can be used for example in the event of communication problems or unexpected
tag values.
See also
Diagnostic Options for the "SIMATIC S5 PROFIBUS FDL" Channel (Page 395)
Quality Codes of Tags (Page 414)
Monitoring Tag Status Using Global Actions (Page 421)
Using the Tag Status to Monitor Connection Status (Page 420)
How to Check an Internal Tag (Page 422)
Channel diagnosis (Page 371)
General Information about Error Detection (Page 370)
Possibilities for Diagnosing the "OPC" Channel (Page 404)
"SIMATIC S7 Protocol Suite" Channel - Diagnostic Options (Page 384)
"System Info" Channel - Diagnostic Options (Page 379)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
369
Communication - Diagnostics
17.2 General Information about Error Detection
17.2
General Information about Error Detection
A fault or error in establishing a communication link is generally first detected in Runtime.
Objects dynamized using WinCC tags, which cannot be supplied with current process values,
are displayed in the process picture as inactive. These could be e.g. I/O fields, slider objects
or bar graphs.
If the fault does not affect some of a connection's WinCC tags, this indicates that one of the
WinCC tags is the source of the trouble. In this case, you should for example check the
addressing of the tags as well as their spelling when used in Graphics Designer.
If the fault affects all of a connection's WinCC tags, this indicates a fault in the connection itself.
The following sections describe which measures and means can be used to pinpoint the source
of the error.
370
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.3 Channel Diagnosis
17.3
Channel Diagnosis
17.3.1
Channel diagnosis
The following functions are available to support the diagnosis of channels and their
connections:
● "Status - Logical Connections" Function
● WinCC "Channel Diagnosis"
See also
How to Use the "Status - Logical Connections" Function to Check a Channel (Page 371)
"Status - Logical Connections" Function (Page 371)
Principle of Channel Diagnosis (Page 373)
17.3.2
"Status - Logical Connections" Function
With the "Status - Logical Connections" function, WinCC Explorer offers a simple way to display
the current status of all configured connections. However, the status can only be displayed in
Runtime.
The function is started in WinCC Explorer via the "Tools" menu.
Note
Detailed data regarding the connection status can be obtained with "WinCC Channel
Diagnosis".
17.3.3
How to Use the "Status - Logical Connections" Function to Check a Channel
Introduction
This section describes how to use the "Status - Logical Connections" function to display the
current status of all configured connections.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
371
Communication - Diagnostics
17.3 Channel Diagnosis
Requirements
● Configure a channel and create a tag in this channel.
Procedure
1. Click the appropriate button in the WinCC Explorer toolbar to activate Runtime.
2. In the WinCC Explorer "Tools", select option "Status of Driver Connections". The "Status Logical Connections" dialog opens.
3. In the "Update" area, you can specify that an update is to be done cyclically. Otherwise,
you can start an update of the display manually by clicking the "Update" button.
4. The configured connections are displayed in the "Name" column. The "Status" column
displays the status of the respective connection.
5. Check the entries in the "Status" column. The "Disconnected" status indicates either a
configuration or hardware error.
Further information can be found under "Channel Diagnosis" for the associated channel.
372
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.3 Channel Diagnosis
17.3.4
Diagnosis of Channels with Channel Diagnosis
17.3.4.1
Principle of Channel Diagnosis
Introduction
The WinCC Channel Diagnosis enables WinCC users to gain a quick overview of the status
of the active connections in Runtime. On the one hand, "Channel Diagnosis" provides status
and diagnostic information regarding channel units and, on the other hand, it serves as a user
interface for the configuration of the diagnostic output:
● The output of statistics or information on the status of the communication e.g. in a process
picture
● Text output in a logbook file for fault analysis and correction by Service.
● Text output in a trace file to assist the Hotline in pinpointing the cause of communication
problems.
The Diagnostic module can be inserted into a process picture as an ActiveX control or be
started as an independent application from the Windows Start menu. The module only displays
status information for channels that support diagnosis.
The diagnosis of a channel's tag can be found in the description of the channel-specific
diagnosis.
Logbook file
Channel Diagnosis creates a logbook file named <Channel_name.log> for every configured
WinCC channel. The system records important information and errors in these. The exact text
content depends on the channel.
The creation of the file and the output text cannot be configured.
The logbook files contain information such as the start and end messages, version information
and information regarding communication errors.
Each entry in the file consists of a data and time stamp, the flag name and a description. The
file is always saved immediately after an entry to ensure that e.g., in the event of a voltage
drop, all of the information possible is available.
Trace File
A trace file named <Channel_name.trc> can be created to hold error messages and any
additional information for every configured WinCC channel. You can select in Runtime whether
to use a trace file. When the trace function is activated, a message will be displayed warning
that the link's propagation time is affected.
Each entry in a trace file has a time stamp followed by a flag name and description.
When the trace function is enabled all information recorded in the logbook is also written to
the trace file.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
373
Communication - Diagnostics
17.3 Channel Diagnosis
The information recorded in a trace file is intended to assist the Hotline in pinpointing the cause
of communication problems.
Note
The trace and logbook file entries are only recorded in English.
Both files are saved in the "Diagnostics" directory in the WinCC directory structure.
The current counter values are not recorded in these files.
See also
Channel Diagnosis with ActiveX Control (Page 374)
How to Check a Channel with Channel Diagnosis as an ActiveX Control (Page 374)
Diagnosing a Channel with "Channel Diagnosis" (Page 375)
How to Check a Channel with Channel Diagnosis (Page 376)
How to Configure the Trace Function of a Channel (Page 377)
How to Start Runtime (Page 378)
17.3.4.2
Channel Diagnosis with ActiveX Control
Introduction
The status information for a channel can also be displayed in a process picture by the "WinCC
Channel Diagnosis Control" ActiveX control.
The ActiveX control is found in the "Controls" object palette in Graphics Designer and is simply
inserted in a picture. The user can thus create e.g. a diagnostics process picture, in which he
can view the status of the communication and other information in Runtime, without needing
to reconfigure this arrangement every time.
17.3.4.3
How to Check a Channel with Channel Diagnosis as an ActiveX Control
Introduction
This section shows how to configure the diagnosis of a channel using the "WinCC Channel
Diagnosis Control" ActiveX control.
374
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.3 Channel Diagnosis
Requirements
● Configure a channel and create a tag in this channel.
Procedure
1. Start Graphics Designer and open a picture.
2. Insert the "WinCC Channel Diagnosis Control" ActiveX control into the picture. This is
accomplished by selecting the ActiveX control from the "Controls" object palette, inserting
it into the picture and dragging it to the desired size.
3. Save the picture.
4. Click the appropriate button in the Graphics Designer toolbar to activate Runtime.
5. Select the picture into which you have inserted the ActiveX control. The status information
for the channels appears in the "Channel Diagnosis" application window on the "Channels/
Connection" tab.
6. Click the "Configuration" tab. Select one of the displayed channels and configure which
error messages are to be recorded in the associated log file.
7. More information about the activation of the Trace function can be found under "Configuring
a Channel's Trace Function".
Note
Channel Diagnosis only displays status information for channels that support channel
diagnosis.
See also
How to Configure the Trace Function of a Channel (Page 377)
17.3.4.4
Diagnosing a Channel with "Channel Diagnosis"
Introduction
Independent of WinCC, Channel Diagnosis can also be started as an application from the
Windows Start menu.
Channel Diagnosis is thus always available and not dependent on the selection of a process
picture, as is the case with WinCC Channel Diagnosis Control. The status information is only
displayed by Channel Diagnosis when WinCC is in Runtime.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
375
Communication - Diagnostics
17.3 Channel Diagnosis
17.3.4.5
How to Check a Channel with Channel Diagnosis
Introduction
This section describes how to start Channel Diagnosis as an application from the Windows
Start menu.
Requirements
● Configure a channel and create a tag in this channel.
Procedure
1. In the Windows Start menu, select the entry "Channel Diagnosis" in the "Simatic/WinCC/
Tools" group.
2. The Channel Diagnosis application window opens. If no WinCC project is currently in
Runtime, message "No connection to WinCC" is displayed.
3. Click the appropriate button in the WinCC Explorer toolbar to activate Runtime.
4. Select the picture into which you have inserted the ActiveX control. The status information
for the channels appears in the Channel Diagnosis application window on the "Channels/
Connection" tab.
5. Click the "Configuration" tab. Select one of the displayed channels and configure which
error messages are to be recorded in the associated log file.
6. More information about the activation of the Trace function can be found under "Configuring
a Channel's Trace Function".
Note
Channel Diagnosis only displays status information for channels that support channel
diagnosis.
See also
How to Configure the Trace Function of a Channel (Page 377)
How to Start Runtime (Page 378)
376
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.3 Channel Diagnosis
17.3.4.6
How to Configure the Trace Function of a Channel
Introduction
This section describes how to configure and activate a Trace function of a channel in Runtime.
Additional information regarding errors and the status of the communication is recorded in the
Trace file.
Note
The information recorded in a trace file is intended to assist the Hotline in pinpointing the
cause of communication problems. For this reason, the evaluation of the data in the file is
not further described here.
Requirements
● Configure a channel plus a connection and a tag.
● Activate the WinCC project.
Standard Flags - Overview
Flag
Description
Fatal Error
Serious error (requires user action)
Error
Error (frame error, etc.)
Warning
Warning (checksum error, etc.)
Information
Information (function call, etc.)
Success
Successful execution (completion of function call, etc.)
Check User Flags
Enables the "User Flags" check boxes
Procedure
1. Start the WinCC Channel Diagnosis from the Start menu.
2. On the "Configuration" tab, select the desired channel.
3. Under "Flags", activate the status and error messages to be recorded in the Trace file. A
description of the standard flags can be found in the "Default Flags - Overview" table.
4. Select the "Check User Flags" check box, if the "User Flags" are to be recorded in the Trace
file. The number and significance of the "User Flags" is depending on the channel.
5. Select the check boxes of the desired "User Flags". By clicking the "Set" or "Reset" buttons,
you can set or reset all "User Flags".
6. In the "Trace File" section, select the "Enable" check box. This activates the other fields in
this area.
7. In the "max. Files" field, enter the maximum number of Trace files.
8. In the "max. Size" field, set the size of the individual Trace files.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
377
Communication - Diagnostics
17.3 Channel Diagnosis
9. Activate the "Overwrite" field, if the channel's existing Trace files are to be overwritten beginning with the oldest - after the maximum number of files and file size has been reached.
10.Click "Save" to save the settings and activate the changes.
17.3.4.7
How to Start Runtime
Requirements
A startup picture must be defined before Runtime is activated.
Procedure
1. Save and close all files that may be open in an editor.
2. Select WinCC Explorer.
3. Activate the project by clicking the "Activate" button in the toolbar or by selecting "Activate"
in the "File" menu.
See also
How to Check a Channel with Channel Diagnosis (Page 376)
378
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.4 Diagnosis of "System Info" Channel
17.4
Diagnosis of "System Info" Channel
17.4.1
"System Info" Channel - Diagnostic Options
The following options for the diagnosis of the "System Info" channel or one of its tags are
available:
Diagnosis of the Channel with "Channel Diagnosis"
"Channel Diagnosis" can query the status of the channel and connection in Runtime. Any errors
that occur are displayed using "Error Codes".
Diagnosis of the Channel Tags
In tag management in Runtime, you can query the current value, the current quality code and
the last time that the tag was changed.
See also
How to Check a Tag (Page 382)
How to Check the Channel and the Connection (Page 380)
17.4.2
Description of Log File Entries
Introduction
The channel records errors and important status changes in the log file. These entries can be
used to analyze a communication problem.
Each entry in the file has a date and time stamp followed by a flag name and description.
Example of a logbook entry:
2000-03-10 12:00:21,050 INFO Log starting ...
2000-03-10 12:00:21,050 INFO | LogFileName : C:\Siemens\WinCC\Diagnose
\SYSTEM_INFO_01.LOG
2000-03-10 12:00:21,050 INFO | LogFileCount : 3
2000-03-10 12:00:21,050 INFO | LogFileSize : 1400000
2000-03-10 12:00:21,050 INFO | TraceFlags : fa000001
2000-03-10 12:00:21,050 INFO start timer
2000-03-10 12:00:21,360 ERROR Illegal tag type! tag: "Format_0" correct type: "Text Tag 8Bit Character Set"!
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
379
Communication - Diagnostics
17.4 Diagnosis of "System Info" Channel
Entries for "INFO" Flag
Message text
Description
Log starting ...
Start message
LogFileName : C:\ Siemens\ WinCC\
Diagnose\ "channel_name".LOG
Name of the log file with path
LogFileCount : "n"
Number of log files of the channel
LogFileSize : "x"
Size of the individual log files in bytes
TraceFlags : fa000001
Flags used by the channel in hexadecimal format
start timer
Start message
Entries for "ERROR" Flag
Message text
Description
Illegal tag type! tag: "tag" correct type: "data
type"!
Incorrect data type of a tag
tag= Name of tag with incorrect data type
data type = Correct data type
17.4.3
Determining the Cause of Incorrect Tag Values
17.4.3.1
How to Determine the Cause of Incorrect Tags
If an unexpected tag value occurs in Runtime, proceed as follows to determine the cause:
1. Check the channel and connections
2. Check the tags of the channel
See also
How to Check a Tag (Page 382)
How to Check the Channel and the Connection (Page 380)
17.4.3.2
How to Check the Channel and the Connection
Introduction
This section describes how to check the "System Info" channel and its connection in Runtime.
Requirements
● Configure a connection and tag for the "System Info" channel.
● Activate the WinCC project.
380
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.4 Diagnosis of "System Info" Channel
Overview of Status Messages
Icon
Description
Channel / connection unconditionally ready
Channel / connection ready with some restrictions
Channel / no statement possible regarding connection status
Channel / connection failed
Procedure
1. Start the WinCC Channel Diagnosis from the Start menu.
2. The Channel Diagnosis application window opens. The status information for all installed
channels and their connections is displayed on the left on the "Channels/Connections" tab.
3. Check the icons in front of the channel named "System Info" and its connection. If the status
of the channel and connection are OK, a green check mark is displayed in front of each
respective entry. For information on the significance of the individual icons refer to the
"Overview of Status Messages" table.
4. If there is no green check mark in front of the channel's name and the connection, select
the connection in the window on the left. In the window on the right, check the counter
values for "Address Error", Size Error" and "Type Error". These values indicate the errors
detected.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
381
Communication - Diagnostics
17.4 Diagnosis of "System Info" Channel
5. Check the channel-specific log file. To do this, use a text editor to open the file in the
directory "Siemens\WinCC\Diagnose". Check the latest entries with the "ERROR" flag. For
more information on this topic, refer to "Description of Log File Entries".
6. If you are still unable to pinpoint the error after checking the log file, please activate the
Trace function and contact Customer Support.
For more information on this topic, refer to "Configuring a Trace Function of a Channel".
See also
How to Configure the Trace Function of a Channel (Page 377)
Description of Log File Entries (Page 379)
How to Check a Tag (Page 382)
17.4.3.3
How to Check a Tag
Introduction
If an external tag does not have the expected value in Runtime, you can use the following
procedure to check the tag.
Requirements
● Configure a connection and tag for the "System Info" channel.
● Activate the WinCC project.
Procedure
1. In WinCC Explorer in the tag management, select the "System Info" channel.
2. In the data window, select the external tag that you wish to check. To do this, open the
directory structure until the tag is displayed in the data window.
3. Move the mouse pointer over the tag to be checked. A tooltip window opens showing the
current tag value, the quality code and the last time that the value changed.
4. Check the quality code. If value "80" is displayed, the tag value is OK. A description of the
other values can be found under "Tag Quality Codes".
5. If the quality code is not equal to "80", select the tag in the tag management and click
"Properties" in the shortcut menu to open the "Tag Properties" dialog.
6. Check whether values have been configured for the upper or lower limits, the start or
substitute values on the "Limits/Reporting" tab. These values can affect the display.
7. If the tag value is affected by one of the configured values, deactivate the project and
change the limit or substitute value.
382
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.4 Diagnosis of "System Info" Channel
Note
Tag values, quality codes etc. are only displayed in Runtime.
See also
Quality Codes of Tags (Page 414)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
383
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
17.5
Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
17.5.1
"SIMATIC S7 Protocol Suite" Channel - Diagnostic Options
The following options for the detection of errors and the diagnosis of the "SIMATIC S7 Protocol
Suite" channel or one of its tags are available:
Checking the Communication Processor Configuration
Besides checking the access point, the communication processor can be tested with the "Set
PG/PC Interface" application. The communication processor can be checked under SIMATIC
NET in the same way.
Checking the Configuration of the Connection and Tags
There may be errors in the configuration of the system and connection parameters. Invalid tag
values may also result from improperly addressing the tag in the AS.
Diagnosis of the Channel with "Channel Diagnosis"
"Channel Diagnosis" can query the status of the channel and connection in Runtime. Any errors
that occur are displayed using "Error Codes".
Diagnosis of the Channel Tags
In tag management in Runtime, you can query the current value, the current quality code and
the last time that the tag was changed.
See also
How to Check a Tag (Page 393)
How to Check the Channel and the Connection (Page 391)
How to Check the Configuration of the Connection and Tags (Page 390)
Checking the Communication Processor under SIMATIC NET (Page 389)
How to Check the Configuration of the Communication Processor (Page 387)
17.5.2
Description of Log File Entries
Introduction
The channel records errors and important status changes in the log file. These entries can be
used to analyze a communication problem.
Each entry in the file has a date and time stamp followed by a flag name and description.
384
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
Example of a logbook entry:
1999-04-01 12:00:24,524 INFO Log starting ...
1999-04-01 12:00:24,524 INFO LogFileName : C:\Siemens\WinCC\Diagnose
\SIMATIC_S7_Protocol_Suite_01.LOG
1999-04-01 12:00:24,524 INFO LogFileCount : 3
1999-04-01 12:00:24,524 INFO LogFileSize : 1400000
1999-04-01 12:00:24,524 INFO TraceFlags : c4000000
1999-04-01 12:00:24,524 INFO S7 channel DLL started!
1999-04-01 12:00:26,096 ERROR Illegal tag address "nCPU3_1"!
1999-04-01 12:00:27,428 INFO S7DOS release: @(#)TIS-Block Library DLL Version
C5.0.17.3-REL5,0,17,47,3-BASIS
1999-04-01 12:00:27,428 INFO S7DOS version: V5.0 / 0
1999-04-01 12:00:27,428 INFO S7CHN version: V5.0 / Mar 1 1999 / 22:36:40
1999-04-01 12:00:27,428 INFO S7 channel unit "Industrial Ethernet" activated!
1999-04-01 12:00:27,468 ERROR Cannot connect to "CPU_4": Errorcode 0xFFDF 42C2!
1999-04-01 12:00:27,538 INFO S7 channel unit "MPI" activated!
Description of the Most Important Entries for the "INFO" Flag
Message text
Description
LogFileName : C:\ Siemens\ WinCC\
Diagnose\ "channel_name".LOG
Name of the log file with path
LogFileCount : "n"
Number of log files of the channel
LogFileSize : "x"
Size of the individual log files in bytes
TraceFlags : c4000000
Displays the flags used by the Trace function as a
hexadecimal number
S7 channel DLL started!
Start message
S7 channel DLL terminated!
End message
S7 channel unit "unitname" activated!
Channel unit activated
S7 channel unit "unitname" deactivated!
Channel unit deactivated
S7DOS version: versionsstring
Version information
S7CHN version: versionsstring
Version information
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
385
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
Description of the Most Important Entries for the "ERROR" Flag
Message text
Description
Cannot connect to "connectionname":
Errorcode 0xhhhh ffff!
Communication error
Could not establish a connection to the AS immediately after
activating WinCC. If the connection could be established
without error at least once, the following message is output
in the event of a later error.
nnn = Number of disconnects for this connection
connectionname = Name of the connection
hhh = 1st error code in hex S7DOS / SAPI-S7
ffff = 2nd error code in hex S7DOS / SAPI-S7
386
Cannot connect to "connectionname":
Errorcode 0xhhhh ffff!
Communication error
Could not establish a connection to the AS immediately after
activating WinCC. The connection was established at least
once without error.
Channel API error: errorstring
Channel API error
The channel passed the error string 'errorstring' to WinCC
Explorer. Depending on the significance of the error, the
error string may or may not be displayed in a notice box. For
a description of the error strings, please see the API Error
Text.
Max. count of API errors reached - API
logbook deactivated
Channel API error
Depending on the error and function, errors can occur
cyclically on the API. To avoid filling the logbook file with
these error messages, a maximum of 32 messages are
output for an API error.
Cannot write storage data!
Cannot read storage data / use default
data
Storage data illegal or destroyed / use
default data!
No storage data / use default data!
General Channel Error Messages
Devicename in unit "unitname" changed
from "old devicename" to "new
devicename"
Initialization message
Max. logbooksize reached - Logbook
deactivated
Message sent when log file has exceeded its maximum
length.
The logbook output is monitored for length. If the specified
length is reached, the logbook is deactivated. The message
is only output, when message output causes the max. file
length to be exceeded. No message be output, if the file
length is changed with an editor or the maximum file length
is reduced in the INI file!
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
17.5.3
Determining the Cause of Incorrect Tag Values
17.5.3.1
How to Determine the Cause of Incorrect Tags
If an unexpected tag value occurs in Runtime, proceed as follows to determine the cause:
1. Checking the Configuration of the Communication Processor
2. Checking the Communication Processor under SIMATIC NET
3. Checking the Configuration of the Connection and Tags
4. Check the channel and connections
5. Check the tags of the channel
See also
How to Check a Tag (Page 393)
How to Check the Channel and the Connection (Page 391)
How to Check the Configuration of the Connection and Tags (Page 390)
Checking the Communication Processor under SIMATIC NET (Page 389)
How to Check the Configuration of the Communication Processor (Page 387)
17.5.3.2
How to Check the Configuration of the Communication Processor
Introduction
This section describes how to use the "PG/PC Port" program to check a communication
processor. In this example, a "CP 5613" type processor is used for the PROFIBUS
communication.
Requirements
● Install the CP 5613.
● Install the associated communication driver.
● Configure the CP 5613.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
387
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
Procedure
1. On the Control Panel, click the "Set PG/PC Port" icon. The "Set PG/PC Port" dialog is
opened.
2. Check the entry for the access point. The access point "CP_L2_1:" for Profibus connection
is automatically added when a CP 5613 is installed. Select the entry for this access point.
Click "Properties" to open the "Properties - CP5613_5614(PROFIBUS)" dialog.
3. Check the entry on the "PROFIBUS" tab.
4. Click the "Operational State" tab. Click the "Test" button to execute a function test on the
CP 5613. The test results is shown in the output field below. Depending on the test results,
you can click the "Restart" button to perform a reset and a complete restart of the CP 5613.
5. Click "OK" to close all open dialogs.
See also
How to Check the Configuration of the Connection and Tags (Page 390)
Checking the Communication Processor under SIMATIC NET (Page 389)
388
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
17.5.3.3
Checking the Communication Processor under SIMATIC NET
Introduction
This section explains how to check a communication processor using the "Set PC Station"
program in the SIMATIC NET software.
In this example, the "CP 5613" for the PROFIBUS communication is used to the "SIMATIC S7
Protocol Suite" channel.
Requirements
● Install the CP 5613.
● Install the SIMATIC NET software. For Windows 2000, a version from V6.0 SP5 is required,
with Windows XP a version from V6.1 must be installed.
● Configure the CP 5613 under SIMATIC NET.
Procedure
1. Activate the Windows Start menu, open "SIMATIC / SIMATIC NET / Settings" and select
menu item "Set PC Station". The "Configurations Console PC Station" dialog opens.
2. Check the entry for the access point. Select the "Access Point" directory in the navigation
window. The existing access points are listed in the data window. Upon installation of the
CP 5613, access point "CP_L2_1:" for PROFIBUS communication is added automatically.
Select this access point in the data window. Use the "Properties" menu item from the
shortcut menu to open the "Properties of CP_L2_1:" dialog.
3. Check the entry in the "Assigned Interface Parameters" field. In the case of a CP5613 in a
PROFIBUS network, select entry "CP5613_5614(PROFIBUS)".
4. Open the navigation window, select the "Components" directory and then the "CP5613/
CP5614" subdirectory.
5. Select the "Network Diagnosis" directory. Click the "Test" button to execute a function test
on the CP 5613. The result is displayed in the output window. Depending on the test results,
click the "Restart" button in the "General" directory to perform a reset and then a complete
restart of the CP 5613.
6. Check the list of participants connected to PROFIBUS in the list in the "Bus Participants"
directory. Based on the display, it is possible to determine the function and status of your
own station as well as other participants which are connected.
7. Close the dialog.
8. If a fault is detected in the configuration of the communication processor, modifications can
only be made to the configuration using SIMATIC NET tools. Further information is available
under SIMATIC NET.
See also
How to Check the Configuration of the Connection and Tags (Page 390)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
389
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
17.5.3.4
How to Check the Configuration of the Connection and Tags
Introduction
This section describes how to check the system parameters and the configuration of the
connection and tags. In this example, a "CP 5613" communication processor is used for the
PROFIBUS communication.
Requirements
● Install the CP 5613.
● Install the associated communication driver.
● Configure the CP 5613.
● Configure a connection and tag for the "SIMATIC S7 Protocol Suite" channel.
● Activate the WinCC project.
Procedure
1. In WinCC Explorer in the tag management, select the "SIMATIC S7 Protocol Suite" channel.
In the data window, select the "PROFIBUS" channel unit. In the channel unit shortcut menu,
click "System Parameters". The "System Parameters - PROFIBUS" dialog opens.
2. On the "Unit" tab, check the entry in the "Logical Device Name" field. By default, this is set
to the access point "CP_L2_1:" . The access point is assigned during installation of the
communication processor in the CP 5613 system. Close the dialog.
3. In the tag management navigation window, select the "PROFIBUS" channel unit. In the
data window, select the connection to be checked. In the shortcut menu, click "Properties"
to open the "Connection Properties" dialog.
4. Click the "Properties" button to open the "Connection Parameters - PROFIBUS" dialog.
5. Check the settings on the "Connection" tab. Close the open dialogs.
390
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
6. In the navigation window, select the checked connection. In the data window, select the
tag to be checked. In the shortcut menu, click "Properties" to open the "Tag Properties"
dialog. Check the values in the "Type Conversion" and "Data Type" fields.
7. Click the "Select" button to open the "Address properties" dialog. Check the settings for
addressing the tag in the AS.
8. Click "OK" to close all open dialogs.
See also
How to Check the Channel and the Connection (Page 391)
17.5.3.5
How to Check the Channel and the Connection
Introduction
This section describes how to check the "SIMATIC S7 Protocol Suite" channel and its
connection in Runtime.
Requirements
● Install a communication processor in a WinCC computer, for example the CP 5613 for
PROFIBUS communication.
● Install the associated communication driver.
● Configure the CP 5613.
● Create a STEP7 project.
● Configure a connection and tag for the "SIMATIC S7 Protocol Suite" channel.
● Activate the WinCC project.
Overview of Status Messages
Icon
Description
Channel / connection unconditionally ready
Channel / connection ready with some restrictions
Channel / no statement possible regarding connection status
Channel / connection failed
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
391
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
Procedure
1. Start the WinCC Channel Diagnosis from the Start menu.
2. The Channel Diagnosis application window opens. The status information for all installed
channels and their connections is displayed on the left on the "Channels/Connections" tab.
3. Check the icon in front of the channel named "SIMATIC S7 Protocol Suite" and the
connection. If the channel and connection are OK, a green check mark is displayed in front
of each respective entry. For information on the significance of the individual icons refer to
the "Overview of Status Messages" table.
4. If there is no green check mark in front of the channel's name and the connection, select
the connection in the window on the left. In the window on the right, check the entries for
the counters "First Error Code" and "Last Error Code". These values indicate the errors
detected. You can access Direct Help by clicking the shortcut menu of the value display.
5. On the "Configuration" tab, select the status and error messages, which are to be output
to the log file. This is done by selecting "SIMATIC S7 Protocol Suite" and configuring the
error display. For more information, please refer to "Configuring the Log File of a Channel".
6. Check the channel-specific log file. To do this, use a text editor to open the file in the
directory "Siemens\WinCC\Diagnose". Check the latest entries with the "ERROR" flag. For
more information on this topic, please see "Description of Log File Entries".
7. If you are still unable to pinpoint the error after checking the log file, please activate the
Trace function and contact Customer Support.
For more information on this topic, refer to "Configuring a Trace Function of a Channel".
392
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
See also
How to Configure the Trace Function of a Channel (Page 377)
Description of Log File Entries (Page 384)
How to Check a Tag (Page 393)
17.5.3.6
How to Check a Tag
Introduction
If an external tag does not have the expected value in Runtime, you can use the following
procedure to check the tag.
In a "SIMATIC S7 Protocol Suite" channel, you can also use connection-specific internal tags.
This procedure can also be used to check these tags.
Requirements
● Install a communication module on a WinCC computer, for example the CP 5613 for MPI
communication.
● Install the associated communication driver.
● Configure the CP 5613.
● Create a STEP7 project.
● Configure a connection and tag for the "SIMATIC S7 Protocol Suite" channel.
● Activate the WinCC project.
Procedure
1. In WinCC Explorer in the tag management, select the "SIMATIC S7 Protocol Suite" channel.
2. In the data window, select the external tag that you wish to check. To do this, open the
directory structure until the tag is displayed in the data window.
3. Move the mouse pointer over the tag to be checked. A tooltip window opens showing the
current tag value, the quality code and the last time that the value changed.
4. Check the quality code. If value "80" is displayed, the tag value is OK. A description of the
other values can be found under "Tag Quality Codes".
5. If the quality code is not equal to "80", select the tag in the tag management and click
"Properties" in the shortcut menu to open the "Tag Properties" dialog.
6. Check whether values have been configured for the upper or lower limits, the start or
substitute values on the "Limits/Reporting" tab. These values can affect the display.
7. If the tag value is affected by one of the configured values, deactivate the project and
change the limit or substitute value.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
393
Communication - Diagnostics
17.5 Diagnosis of the "SIMATIC S7 Protocol Suite" Channel
Note
In Runtime, the current values of the connection-specific internal tags can be viewed in detail
with "WinCC Channel Diagnosis". When the main connection is selected, the tags is shown
in the "Counter" column.
Tag values, quality codes etc. are only displayed in Runtime.
See also
Quality Codes of Tags (Page 414)
394
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
17.6
Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
17.6.1
Diagnostic Options for the "SIMATIC S5 PROFIBUS FDL" Channel
The following options for the detection of errors and the diagnosis of the "SIMATIC S5
PROFIBUS FDL" channel or one of its tags:
Checking the Communication Processor Configuration
Besides checking the access point, the communication processor can be tested with the "Set
PG/PC Interface" application. The communication processor can be checked under SIMATIC
NET in the same way.
Checking the Configuration of the Connection and Tags
There may be errors in the configuration of the system and connection parameters. Invalid tag
values may also result from improperly addressing the tag in the AS.
Diagnosis of the Channel with "Channel Diagnosis"
"Channel Diagnosis" can query the status of the channel and connection in Runtime. Any errors
that occur are displayed using "Error Codes".
Diagnosis of the Channel Tags
In tag management in Runtime, you can query the current value, the current quality code and
the last time that the tag was changed.
See also
How to Check a Tag (Page 403)
How to Check the Channel and the Connection (Page 401)
How to Check the Configuration of the Connection and Tags (Page 399)
Checking the Communication Processor under SIMATIC NET (Page 398)
How to Check the Configuration of the Communication Processor (Page 397)
17.6.2
Description of Log File Entries
Introduction
The channel records errors and important status changes in the log file. These entries can be
used to analyze a communications problem.
Each entry in the file has a date and time stamp followed by a flag name and description.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
395
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
Example of a logbook entry:
2000-05-03 14:43:48,733 INFO Log starting ...
2000-05-03 14:43:48,733 INFO | LogFileName : d:\Siemens\WinCC\Diagnose
\SIMATIC_S5_PROFIBUS_FDL_01.LOG
2000-05-03 14:43:48,733 INFO | LogFileCount : 3
2000-05-03 14:43:48,733 INFO | LogFileSize : 1400000
2000-05-03 14:43:48,733 INFO | TraceFlags : fa017fff
Description of the "INFO" Flag Entries
Message text
Description
Log starting ...
Start message
LogFileName : C:\ Siemens\ WinCC\
Diagnose\ "channel_name".LOG
Name of the log file with path
LogFileCount : "n"
Number of log files of the channel
LogFileSize : "x"
Size of the individual log files in bytes
TraceFlags : fa017fff
Displays the flags used by the Trace function as a
hexadecimal number
17.6.3
Determining the Cause of Incorrect Tag Values
17.6.3.1
How to Determine the Cause of Incorrect Tags
If an unexpected tag value occurs in Runtime, proceed as follows to determine the cause:
1. Check the configuration of the communication processor
2. Check the communication processor under SIMATIC NET
3. Check the configuration of the connection and tags
4. Check the channel and connections
5. Check the tags of the channel
See also
How to Check the Configuration of the Connection and Tags (Page 399)
How to Check a Tag (Page 403)
How to Check the Channel and the Connection (Page 401)
Checking the Communication Processor under SIMATIC NET (Page 398)
How to Check the Configuration of the Communication Processor (Page 397)
396
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
17.6.3.2
How to Check the Configuration of the Communication Processor
Introduction
This section describes how to use the "PG/PC Port" program to check a communication
processor. In this example, a "CP 5613" type processor is used for the PROFIBUS
communication.
Requirements
● Install the CP 5613.
● Install the associated communication driver.
● Configure the CP 5613.
Procedure
1. On the Control Panel, click the "Set PG/PC Port" icon. The "Set PG/PC Port" dialog is
opened.
2. Check the entry for the access point. The access point "CP_L2_1:/SCP" is automatically
added for the PROFIBUS connection when a CP 5613 is installed. Select the entry for this
access point. Click "Properties" to open the "Properties - CP5613_5614(PROFIBUS)"
dialog.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
397
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
3. Check the entry on the "PROFIBUS" tab.
4. Click the "Operational State" tab. Click the "Test" button to execute a function test on the
CP 5613. The test results is shown in the output field below. Depending on the test results,
you can click the "Restart" button to perform a reset and a complete restart of the CP 5613.
5. Click "OK" to close all open dialogs.
See also
How to Check the Configuration of the Connection and Tags (Page 399)
Checking the Communication Processor under SIMATIC NET (Page 398)
17.6.3.3
Checking the Communication Processor under SIMATIC NET
Introduction
This section explains how to check a communication processor using the "Set PC Station"
program in the SIMATIC NET software.
In this example, the "CP 5613" type is used for the PROFIBUS communication to channel
"SIMATIC S5 PROFIBUS FDL".
Requirements
● Install the CP 5613.
● Install the SIMATIC NET software. For Windows 2000, a version from V6.0 SP5 is required,
with Windows XP a version from V6.1 must be installed.
● Configure the CP 5613 under SIMATIC NET.
Procedure
1. Activate the Windows Start menu, open "SIMATIC / SIMATIC NET / Settings" and select
menu item "Set PC Station". The "Configurations Console PC Station" dialog opens.
2. Check the entry for the access point. Select the "Access Point" directory in the navigation
window. The existing access points are listed in the data window. Upon installation of the
CP 5613, access point "CP_L2_1:" for PROFIBUS communication is added automatically.
Select this access point in the data window. Use the "Properties" menu item from the
shortcut menu to open the "Properties of CP_L2_1:" dialog.
3. Check the entry in the "Assigned Interface Parameters" field. In the case of a CP5613 in a
PROFIBUS network, select entry "CP5613_5614(PROFIBUS)".
4. Open the navigation window, select the "Components" directory and then the "CP5613/
CP5614" subdirectory.
5. Select the "Network Diagnosis" directory. Click the "Test" button to execute a function test
on the CP 5613. The result is displayed in the output window. Depending on the test results,
click the "Restart" button in the "General" directory to perform a reset and then a complete
restart of the CP 5613.
398
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
6. Check the list of participants connected to PROFIBUS in the list in the "Bus Participants"
directory. Based on the display, it is possible to determine the function and status of your
own station as well as other participants which are connected.
7. Close the dialog.
8. If a fault is detected in the configuration of the communication processor, modifications can
only be made to the configuration using SIMATIC NET tools. Further information is available
under SIMATIC NET.
See also
How to Check the Configuration of the Connection and Tags (Page 399)
17.6.3.4
How to Check the Configuration of the Connection and Tags
Introduction
This section describes how to check the system parameters and the configuration of the
connection and tags.
Requirements
● Install the CP 5613.
● Install the communication driver.
● Configure the CP 5613.
● Configure a connection and tag for the "SIMATIC S5 PROFIBUS FDL" channel.
● Activate the WinCC project.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
399
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
Procedure
1. Click the plus sign in front of the "SIMATIC S5 PROFIBUS FDL" icon in WinCC Explorer
navigation window. In the context menu of the "FDL(CP5412/A2-1)" icon, click "System
Parameters". The "System Parameters" dialog opens.
2. Check the entry in the "Device Name" field. By default, this is set to access point "CP_L2_1:/
SCP". The access point is assigned during installation of the communication processor in
the CP 5613 system. Close the dialog.
3. Click the plus sign in front of the FDL(CP5412/A2-1)" icon. In the context menu of the tag
to be tested, select the "Properties" entry. The "Connection Properties" dialog is opened.
4. In the "Connection Properties" dialog, click the "Properties" button. The "Connection
Parameters" dialog opens.
400
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
5. Check the settings on the "Connection" tab. Close the open dialogs.
6. Click the plus sign in front of the icon of the connection. In the context menu of the tag to
be tested, click the "Properties" entry. The "Tag Properties" dialog opens. Check the entries
in the "Type Conversion" and "Data Type" fields.
7. In the "Tag Properties" dialog, click the "Select" button. The "Address Properties" dialog
opens. Check the settings.
8. Click "OK" to close all open dialogs.
See also
How to Check the Channel and the Connection (Page 401)
17.6.3.5
How to Check the Channel and the Connection
Introduction
This section describes how to check the "SIMATIC S5 PROFIBUS FDL" channel and its
connection in Runtime.
Requirements
● Install the CP 5613.
● Install the communication driver.
● Configure the CP 5613.
● Create a STEP5 project.
● Configure a connection and tag for the "SIMATIC S5 PROFIBUS FDL" channel.
● Activate the WinCC project.
Overview of Status Messages
Icon
Description
Channel / connection unconditionally ready
Channel / connection ready with some restrictions
Channel / no statement possible regarding connection status
Channel / connection failed
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
401
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
Procedure
1. Start the WinCC Channel Diagnosis from the Start menu.
2. The Channel Diagnosis application window opens. The status information for all installed
channels and their connections is displayed on the left on the "Channels/Connections" tab.
3. Check the icon in front of the channel name "SIMATIC S5 PROFIBUS FDL" and the
connection. If the status of the channel and connection are OK, a green check mark is
displayed in front of each respective entry. For information on the significance of the
individual icons refer to the "Overview of Status Messages" table.
4. If there is no green check mark in front of the channel's name and the connection, select
the connection in the window on the left. In the window on the right, check the entries for
the counters "State", "Error Count", "Error Reason", "Send" and "Receive". These values
indicate the errors detected.
5. Check the channel-specific log file. To do this, use a text editor to open the file in the
directory "Siemens\WinCC\Diagnose". Check the latest entries with the "ERROR" flag. For
more information on this topic, please see "Description of Log File Entries".
6. If you are still unable to pinpoint the error after checking the log file, please activate the
Trace function and contact Customer Support.
For more information on this topic, refer to "Configuring a Trace Function of a Channel".
See also
How to Configure the Trace Function of a Channel (Page 377)
Description of Log File Entries (Page 395)
How to Check a Tag (Page 403)
402
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.6 Diagnosis of the "SIMATIC S5 Profibus FDL" Channel
17.6.3.6
How to Check a Tag
Introduction
If an external tag does not have the expected value in Runtime, you can use the following
procedure to check the tag.
Requirements
● Install the CP 5613.
● Install the communication driver.
● Configure the CP 5613.
● Create a STEP5 project.
● Configure a connection and tag for the "SIMATIC S5 PROFIBUS FDL" channel.
● Activate the WinCC project.
Procedure
1. In WinCC Explorer in tag management, select the "SIMATIC S5 PROFIBUS FDL" channel.
2. In the data window, select the external tag that you wish to check. To do this, open the
directory structure until the tag is displayed in the data window.
3. Move the mouse pointer over the tag to be checked. A tooltip window opens showing the
current tag value, the quality code and the last time that the value changed.
4. Check the quality code. If value "80" is displayed, the tag value is OK. A description of the
other values can be found under "Tag Quality Codes".
5. If the quality code is not equal to "80", select the tag in the tag management and click
"Properties" in the shortcut menu to open the "Tag Properties" dialog.
6. Check whether values have been configured for the upper or lower limits, the start or
substitute values on the "Limits/Reporting" tab. These values can affect the display.
7. If the tag value is affected by one of the configured values, deactivate the project and
change the limit or substitute value.
Note
Tag values, quality codes etc. are only displayed in Runtime.
See also
Quality Codes of Tags (Page 414)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
403
Communication - Diagnostics
17.7 Diagnosis of the "OPC" Channel
17.7
Diagnosis of the "OPC" Channel
17.7.1
Possibilities for Diagnosing the "OPC" Channel
There are the following possibilities for detecting errors and diagnosing the "OPC" channel or
one of its tags:
Checking the Configuration of the Connection and Tags
There may be errors in the configuration of the system and connection parameters. Invalid tag
values may also result from improperly addressing the tag in the AS.
Diagnosis of the Channel with "Channel Diagnosis"
"Channel Diagnosis" can query the status of the channel and connection in Runtime. Any errors
that occur are displayed using "Error Codes".
Diagnosis of the Channel Tags
In tag management in Runtime, you can query the current value, the current quality code and
the last time that the tag was changed.
See also
How to Check a Tag (Page 411)
How to Check the Channel and the Connection (Page 409)
How to Check the Configuration Data (Page 408)
17.7.2
Description of Log File Entries
17.7.2.1
Description of Log File Entries
Introduction
The channel records errors and important status changes in the log file. The following sections
cover only the most important entries. These entries can be used to analyze a communications
problem.
A distinction must be made between two types of entries:
404
●
INFO
●
ERROR
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.7 Diagnosis of the "OPC" Channel
Structure of an Entry
Examples of entries in a logbook
2000-03-24 10:43:18,756 INFO Log starting ...
2000-03-24 10:43:18,756 INFO | LogFileName : C:\Siemens\WinCC\Diagnose\OPC.LOG
2000-03-24 10:43:18,756 INFO | LogFileCount : 3
2000-03-24 10:43:18,756 INFO | LogFileSize : 1400000
2000-03-24 10:43:18,756 INFO | TraceFlags : fa000007
000-03-24 10:43:18,756 INFO Process attached at 2000-03-24 09:43:18,746 UTC
2000-03-23 10:46:18,756 INFO Process detached at 2000-03-2410:46:18,746UTC
2000-03-27 13:22:43,390 ERROR ..FOPCData::InitOPC CoCreateInstanceEx- ERROR
800706ba
2000-03-27 13:22:43,390 ERROR - ChannelUnit::SysMessage("[OPC Groups (OPCHN Unit
#1)]![OPC_No_Machine]: CoCreateInstance for server "OPCServer.WinCC" on machine
OPC_No_Machine failed, Error=800706ba (HRESULT = 800706ba RPC_S_SERVER_UNAVAILABLE (Der RPC-Server ist nicht verfügbar.))")
See also
Entries for "ERROR" Flag (Page 406)
Entries for "INFO" Flag (Page 405)
17.7.2.2
Entries for "INFO" Flag
Introduction
Each entry in the file has a date and time stamp followed by a flag name and description.
Examples of entries in a logbook
2000-03-24 10:43:18,756 INFO Log starting ...
2000-03-24 10:43:18,756 INFO | LogFileName : C:\Siemens\WinCC\Diagnose\OPC.LOG
2000-03-24 10:43:18,756 INFO | LogFileCount : 3
2000-03-24 10:43:18,756 INFO | LogFileSize : 1400000
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
405
Communication - Diagnostics
17.7 Diagnosis of the "OPC" Channel
2000-03-24 10:43:18,756 INFO | TraceFlags : fa000007
000-03-24 10:43:18,756 INFO Process attached at 2000-03-24 09:43:18,746 UTC
2000-03-23 10:46:18,756 INFO Process detached at 2000-03-2410:46:18,746UTC
Description of the Mst Iportant Logbook Entries
17.7.2.3
Message text
Description
Log starting ...
Start message
LogFileName : C:\ Siemens\ WinCC\
Diagnose\ "channel_name".LOG
Name of the log file with path
LogFileCount : "n"
Number of log files of the channel
LogFileSize : "x"
Size of the individual log files in bytes
TraceFlags : fa000007
Displays the flags used by the Trace function as a
hexadecimal number
Process attached at 2000-03-24
09:43:18,746 UTC
The channel was loaded by the WinCC Data Manager.
Process detached at
2000-03-2410:46:18,746 UTC
The channel was unloaded by the WinCC Data
Manager.
IOPCChnShutdown::ShutdownRequest was
called... Reason: system going down"
IOPCChnShutdown::ShutdownRequest
The WinCC OPC Server WinCC project was
deactivated. The WinCC OPC clients are requested to
disconnect from the WinCC OPC server.
Entries for "ERROR" Flag
Introduction
Each entry in the file has a date and time stamp followed by a flag name and description. In
the case of the "Error" flag, the description consists of a message text, error code and the text
of the error message. Some error codes do not have text for an error message.
Examples of entries in a logbook
2000-03-27 13:22:43,390 ERROR ..FOPCData::InitOPC CoCreateInstanceEx- ERROR
800706ba
2000-03-27 13:22:43,390 ERROR - ChannelUnit::SysMessage("[OPC Groups (OPCHN Unit
#1)]![OPC_No_Machine]: CoCreateInstance for server "OPCServer.WinCC" on machine
OPC_No_Machine failed, Error=800706ba (HRESULT = 800706ba RPC_S_SERVER_UNAVAILABLE (RPC server not available.))")
406
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.7 Diagnosis of the "OPC" Channel
Description of the Most Important Logbook Entries
Error Code
Error Message Text
Possible Causes
c0040004
Conversion between the
"canonicalDatatype" and the
"requestedDatatype" is not
supported by the server.
Access to the WinCC tag on the OPC server failed.
Conversion is possible but failed.
The WinCC tag is not on the server or the configured
data type does not match.
c0040007
The name does not exist in the
name space of the server.
The error code is always returned by the server if the
OPC client is accessed with a tag name that does not
exist in the name space of the server.
Examples: Browse, read tag, write tag, insert tag in a
subscription.
00000001
AddItems
Access to the WinCC tag on the OPC server failed.
The WinCC tag is not on the server or the configured
data type does not match.
Data Type WinCC Tag OPC Server = Data Type
WinCC Tag OPC Client.
80004005
Could not resolve Server Name The computer that is used as the WinCC OPC Server
is not available in the network.
The WinCC OPC server, which was accessed by the
"OPC" channel, was not available.
80040154
Class not registered
The WinCC OPC Server is not properly registered in
the system.
The WinCC OPC Server's WinCC project is not
activated.
80070057
Parameter wrong
The WinCC tag is not on the OPC Server, or the
configured data type does not match.
800706ba
The RPC Server is not
available.
The computer on which the OPC Server is to be
started could not be found in the network.
17.7.3
Determining the Cause of Incorrect Tag Values
17.7.3.1
How to Determine the Cause of Invalid Tags
If an unexpected tag value occurs in Runtime, proceed as follows to determine the cause:
1. Check the configuration data
2. Check connection
3. Check the tags of the channel
See also
How to Check a Tag (Page 411)
How to Check the Channel and the Connection (Page 409)
How to Check the Configuration Data (Page 408)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
407
Communication - Diagnostics
17.7 Diagnosis of the "OPC" Channel
17.7.3.2
How to Check the Configuration Data
Requirements
● A computer as WinCC OPC Client with a WinCC Project.
● The "OPC" channel must be integrated in the OPC client's WinCC project.
● Configure a WinCC tag in the OPC server's WinCC project.
● On the OPC client configure a connection and a WinCC tag, which communicates with the
created server tags.
● Activate the WinCC project on the OPC Server and Client.
Procedure
1. Click the plus sign in front of the "OPC" icon in WinCC Explorer navigation window on the
OPC client. Click the "plus sign in front of the icon "OPC Groups (OPCHN Unit#1)".
2. In the shortcut menu of the tag to be tested, select the "Properties" entry. The "Connection
Properties" dialog is opened. Click the "OPC Group" tab.
3. In the field "OPC Server Name", check the ProgID of the OPC server.
In the case of a connection to a server with WinCC V 5.0 or higher, you must enter
"OPCServer.WinCC".
In the case of a server running WinCC V4.x, you must enter "OE.Groups".
4. Enter the name of the computer to serve as the OPC Server in the "Start the server on this
computer" field. Click the "Test Server" button to test the connection to the OPC Server.
Close the dialog.
5. Click the plus sign in front of the icon of the connection. In the context menu of the tag to
be tested, click the "Properties" entry. The "Tag Properties" dialog opens.
6. The same "Data Type" must be entered for this tag as for the tag on the OPC Server.
7. In the "Tag Properties" dialog, click the "Select" button. The "Address Properties" dialog
opens.
8. Check the entries in the fields "Item Name" and "Data Type". The "Item Name" must match
the tag name on the OPC Server. The "Data Type" must match the data type of the tag on
the OPC Server.
9. Check the channel-specific log file. To do this, use a text editor to open the file in the
directory "Siemens\WinCC\Diagnose". Check the latest entries with the "ERROR" flag. For
more information on this topic, refer to "Description of Log File Entries".
10.If you are still unable to pinpoint the error after checking the log file, please activate the
Trace function and contact Customer Support.
For more information on this topic, refer to "Configuring a Trace Function of a Channel".
408
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.7 Diagnosis of the "OPC" Channel
See also
How to Configure the Trace Function of a Channel (Page 377)
Description of Log File Entries (Page 404)
How to Check the Channel and the Connection (Page 409)
17.7.3.3
How to Check the Channel and the Connection
Introduction
This section describes how to check the "OPC" channel and its connection in Runtime.
Requirements
● A computer as WinCC OPC Client with a WinCC Project.
● The "OPC" channel must be integrated in the OPC client's WinCC project.
● Configure a WinCC tag in the OPC server's WinCC project.
● On the OPC client configure a connection and a WinCC tag, which communicates with the
created server tags.
● Activate the WinCC project on the OPC Server and Client.
Overview of Status Messages
Icon
Description
Channel / connection unconditionally ready
Channel / connection ready with some restrictions
Channel / no statement possible regarding connection status
Channel / connection failed
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
409
Communication - Diagnostics
17.7 Diagnosis of the "OPC" Channel
Procedure
1. Start the WinCC Channel Diagnosis from the Start menu.
2. The Channel Diagnosis application window opens. The status information for all installed
channels and their connections is displayed on the left on the "Channels/Connections" tab.
3. Check the icons in front of the OPC connection. If the status of the connection is OK, a
green check mark is displayed in front of the respective entry. For information on the
significance of the individual icons refer to the "Overview of Status Messages" table.
4. If there is no green check mark in front of the name of the connection, select the connection
in the window on the left. In the window on the right, check the entries for the counters
"AddItemFailures", "Server Status", "Last Error" and "Last Error Name". These values
indicate the errors detected.
5. Check the channel-specific log file. To do this, use a text editor to open the file in the
directory "Siemens\WinCC\Diagnose". Check the latest entries with the "ERROR" flag. For
more information on this topic, refer to "Description of Log File Entries".
6. If you are still unable to pinpoint the error after checking the log file, please activate the
Trace function and contact Customer Support.
For more information on this topic, refer to "Configuring a Trace Function of a Channel".
See also
How to Configure the Trace Function of a Channel (Page 377)
Description of Log File Entries (Page 404)
How to Check a Tag (Page 411)
410
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.7 Diagnosis of the "OPC" Channel
17.7.3.4
How to Check a Tag
Introduction
If an external tag does not have the expected value in Runtime, you can use the following
procedure to check the tag.
Requirements
● A computer as WinCC OPC Client with a WinCC Project.
● The "OPC" channel must be integrated in the OPC client's WinCC project.
● Configure a WinCC tag in the OPC server's WinCC project.
● On the OPC client configure a connection and a WinCC tag, which communicates with the
created server tags.
● Activate the WinCC project on the OPC Server and Client.
Procedure
1. In WinCC Explorer in tag management, select the "OPC" channel.
2. In the data window, select the external tag that you wish to check. To do this, open the
directory structure until the tag is displayed in the data window.
3. Move the mouse pointer over the tag to be checked. A tooltip window opens with the current
tag value, the quality value and the time of the most recent change.
4. Check the quality code. If the value "C0" is displayed, the tag value is OK. A description of
the other values can be found under "Tag Quality Codes".
5. If the quality code is not equal to "C0", select the tag in tag management and click
"Properties" in the shortcut menu to open the "Tag Properties" dialog.
6. Check whether values have been configured for the upper or lower limits, the start or
substitute values on the "Limits/Reporting" tab. These values can affect the display.
7. If the tag value is affected by one of the configured values, deactivate the project and
change the limit or substitute value.
Note
Tag values, quality codes etc. are only displayed in Runtime.
See also
Quality Codes of Tags (Page 414)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
411
Communication - Diagnostics
17.8 Quality of Tags
17.8
Quality of Tags
17.8.1
Quality of Tags
Introduction
In WinCC, there are two quality indicators that allow you to evaluate the quality of tags. These
two indicators are tag status and quality code.
The tag status is formed in WinCC and informs of the quality of configuration settings within
the OS. The tag status informs additionally of the connection status to the WinCC
communication partner. This may be an automated system or the server computer.
The quality code contains the same information as the tag status. In addition to this information,
the quality status contains quality statements on partners which assess or process tags.
Possible partners are:
● Automation systems
● Automation systems with field devices
● OPC server
● OPC server with subordinate automation systems
Therein the quality code is forwarded within the processing chain. If at one point in the
processing chain several quality codes are pending for a tag, the worst code is forwarded.
The quality code informs of the quality of a tag independent of where this code was formed.
412
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.8 Quality of Tags
Cascading of Quality Code
By using the example of an automation system with field device connected, the cascading of
quality codes shall be outlined.
The automation system reads the quality codes generated by the field device. Using an
analysis logic, quality codes pending for the same tag concurrently are evaluated by priority.
The quality code with the worst status is assigned to the tag. This quality code must be saved
in a data block directly behind the associated tag value.
You may initiate the analysis logic using the channel modules of the PCS7 Library. If the PCS7
Library is not available to you, you must configure the analysis logic in the automation system
yourself.
Using one of the communication drivers, WinCC reads the tags from the automation device in
Runtime, including the associated quality codes. For each tag, the tag status is formed in the
data manager. It contains, for example, violations of configured measurement range limits as
well as the status of linkage between WinCC and the automation device.
Using the analysis logic in the data manager, the quality code is generated from the tag status
of the data manager and the quality code of the automation device. Here too, the code with
the worst status is passed on and saved as quality code by WinCC. For tags that do not have
a quality code in the automation system, the quality code is always identical with the tag status.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
413
Communication - Diagnostics
17.8 Quality of Tags
17.8.2
Quality Codes of Tags
Introduction
The quality code is needed to check status and quality of a tag. The displayed quality code
summarizes the quality of the entire value transmission and value processing for the respective
tag. Thus with the quality code you can for example see whether the current value is a start
value or a substitute value.
The quality codes are prioritized. If several codes occur at the same time, the code with the
worst status is displayed.
Evaluation of Quality Codes
Quality codes can be evaluated in a number of different ways:
● Evaluation with VB scripts
● Evaluation with C scripts
● Evaluation through the dynamic dialog
● Evaluation of the "Quality Code Change Tag" result of an I/O field
Note
In order to include the entire value transfer and value processing in the quality code for a
process tag, the connected automation system must support the quality code. When
configuring the tags in the AS, make sure there is enough memory space for the quality code.
In an AS from the S7 family, for example, the quality code needs an additional byte that is
appended to the process value. To prevent errors, this byte must be taken into account when
configuring a tag, for instance at the end of a data block.
Display of Quality Codes in Process Pictures
For the display of tag values in graphic objects with process connection, the quality code may
affect the display. If the quality code has a value of 0x80 (good) or 0x4C (initial value), the
display of the tag value is not grayed out. For all other values, the display is grayed out. In
414
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.8 Quality of Tags
addition, a yellow warning triangle is displayed for the following objects depending on the set
WinCC design:
● I/O field
● Bar, 3D bar
● Check box, radio box
● Group display, status display
● Slider object
Structure
The quality code has the following binary structure:
QQSSSSLL
Q: Quality
S: Substatus of the quality
L: Limits. This value is optional.
Note
The quality codes shown in the "Quality" table are basic values of the quality stages. Making
use of the substatus and limit elements gives rise to intermediate values over and above the
quality stage concerned.
Quality
The first two digits specify the quality of the tag.
Q Q S S S S L L
2 2 2 2 2 2 2 2
7
6
5
4
3
2
1
0
Bad - The value is not useful
0 0 - - - - - -
Uncertain - The quality of the value is less than normal, but the value may still
be useful.
0 1 - - - - - -
Good (non-cascade) - The quality of the value is good. Possible alarm
conditions may be indicated by the sub-status.
1 0 - - - - - -
Good (cascade) - The value may be used in control.
1 1 - - - - - -
Substatus
The quality alone is not enough. Individual qualities are divided into substatuses. The quality
code is binary coded. In order to analyze quality codes their values must be converted into
their hexadecimal representation.
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
415
Communication - Diagnostics
17.8 Quality of Tags
Quality Codes of Tags
Possible quality codes are listed in the following table. At the top of the list, you find the poorest
quality code, while the best quality code is shown at the bottom of the list. The best quality
code is assigned the lowest priority, while the poorest quality code is assigned the highest
priority. If several statuses occur for one tag in the process, the poorest code is passed on.
416
Code
(Hex)
Quality
Q Q SSSSL L
0x23
Bad
Device passivated - Diagnostic alerts inhibited
0 0 1 0 0 0 1 1
0x3F
Bad
Function check - Local override
0 0 1 1 1 1 1 1
0x1C
Bad
Out of Service - The value is not reliable because the block is
not being evaluated, and may be under construction by a
configuration planner. Set if the block mode is O/S.
0 0 0 1 1 1 - -
0x73
Uncertain
Simulated value - Start
0 1 1 1 0 0 1 1
0x74
Uncertain
Simulated value - End
0 1 1 1 0 1 - -
0x84
Good
(noncascade)
Active Update event - Set if the value is good and the block
has an active Update event.
1 0 0 0 0 1 - -
0x24
Bad
Maintenance alarm - More diagnostics available.
0 0 1 0 0 1 - -
0x18
Bad
No Communication, with no usable value - Set if there has
never been any communication with this value since it was
last "Out of Service".
0 0 0 1 1 0 - -
0x14
Bad
No Communication, with last usable value - Set if this value
had been set by communication, which has now failed.
0 0 0 1 0 1 - -
0x0C
Bad
Device failure - Set if the source of the value is affected by a
device failure.
0 0 0 0 1 1 - -
0x10
Bad
Sensor failure
0 0 0 1 0 0 - -
0x08
Bad
Not Connected - Set if this input is required to be connected
and is not connected.
0 0 0 0 1 0 - -
0x04
Bad
Configuration error - Set if the value is not useful because
there is some inconsistency regarding the parameterization
or configuration, depending on what a specific manufacturer
can detect.
0 0 0 0 0 1 - -
0x00
Bad
Non-specific - There is no specific reason why the value is
bad. Used for propagation.
0 0 0 0 0 0 - -
0x28
Bad
Process related - Substitute value
0 0 1 0 1 0 - -
0x2B
Bad
Process related - No maintenance
0 0 1 0 1 0 1 1
0x68
Uncertain
Maintenance demanded
0 1 1 0 1 0 - -
0x60
Uncertain
Simulated value - Set when the process value is written by
the operator while the block is in manual mode.
0 1 1 0 0 0 - -
0x64
Uncertain
Sensor calibration
0 1 1 0 0 1 - -
0x5C
Uncertain
Configuration error
0 1 0 1 1 1 - -
0x58
Uncertain
Subnormal
0 1 0 1 1 0 - -
0x54
Uncertain
Engineering unit range violation - Set if the value lies outside
of the set of values defined for this parameter. The limits
define which direction has been exceeded.
0 1 0 1 0 1 - -
0x50
Uncertain
Sensor conversion not accurate
0 1 0 1 0 0 - -
0x4B
Uncertain
Substitute (constant)
0 1 0 0 1 0 1 1
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.8 Quality of Tags
Code
(Hex)
Quality
0x78
Uncertain
Process related - No maintenance
0 1 1 1 1 0 - -
0x4C
Uncertain
Initial value - Value of volatile parameters during and after
reset of the device or of a parameter.
0 1 0 0 1 1 - -
0x48
Uncertain
Substitute value - Predefined value is used instead of the
calculated one. This is used for fail safe handling.
0 1 0 0 1 0 - -
0x44
Uncertain
Last usable value - Whatever was writing this value has
stopped doing so. This is used for fail safe handling.
0 1 0 0 0 1 - -
0x40
Uncertain
Non-specific - There is no specific reason why the value is
uncertain.
0 1 0 0 0 0 - -
0xE0
Good
Initiate fail safe (IFS) - The value is from a block that wants its
(cascade) downstream output block (e.g. AO) to go to fail safe.
1 1 1 0 0 0 - -
0xD8
Good
Local override (LO) - The value is from a block that has been
(cascade) locked out by a local key switch or is a Complex AO/DO with
interlock logic active. The failure of normal control must be
propagated to a function running in a host system for alarm
and display purposes. This also implies "Not Invited".
1 1 0 1 1 0 - -
0xD4
Good
Do not select (DNS) - The value is from a block which should
(cascade) not be selected, due to conditions in or above the block.
1 1 0 1 0 1 - -
0xCC
Good
Not invited (NI) - The value is from a block which does not
(cascade) have a target mode that would use this input.
1 1 0 0 1 1 - -
0xC8
Good
Initialization request (IR) - The value is an initialization value
(cascade) for a source (back calculation input parameter), because the
lower loop is broken or the mode is wrong.
1 1 0 0 1 0 - -
0xC4
Good
Initialization acknowledge (IA) - The value is an initialized
(cascade) value from a source (cascade input, remote-cascade in, and
remote-output in parameters).
1 1 0 0 0 1 - -
0xC0
Good
OK - No error or special condition is associated with this value. 1 1 0 0 0 0 - (cascade)
0xA0
Good
(noncascade)
Initiate fail safe
1 0 1 0 0 0 - -
0x98
Good
(noncascade)
Unacknowledged critical alarm - Set if the value is good and
the block has an unacknowledged alarm with a priority greater
than or equal to 8.
1 0 0 1 1 0 - -
0x94
Good
(noncascade)
Unacknowledged advisory alarm - Set if the value is good and
the block has an unacknowledged alarm with a priority less
than 8.
1 0 0 1 0 1 - -
0x90
Good
(noncascade)
Unacknowledged update event - Set if the value is good and
the block has an unacknowledged update event.
1 0 0 1 0 0 - -
0x8C
Good
(noncascade)
Active critical alarm - Set if the value is good and the block
has an active alarm with a priority greater than or equal to 8.
1 0 0 0 1 1 - -
0x88
Good
(noncascade)
Active advisory alarm - Set if the value is good and the block
has an active alarm with a priority less than 8.
1 0 0 0 1 0 - -
0xA8
Good
(noncascade)
Maintenance demanded
1 0 1 0 1 0 - -
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Q Q SSSSL L
417
Communication - Diagnostics
17.8 Quality of Tags
Code
(Hex)
Quality
Q Q SSSSL L
0xA4
Good
(noncascade)
Maintenance required
1 0 1 0 0 1 - -
0xBC
Good
(noncascade)
Function check - Local override
1 0 1 1 1 1 - -
0x80
Good
(noncascade)
OK - No error or special condition is associated with this value. 1 0 0 0 0 0 - -
Limit
Quality codes can be further subdivided by limits. Limits are optional.
Q Q S S S S L L
O.K. - The value is free to move.
-
-
-
-
-
-
0 0
Low limited - The value has acceded its low limits.
-
-
-
-
-
-
0 1
High limited - The value has acceded its high limits.
-
-
-
-
-
-
1 0
Constant (high and low limited) - The value cannot move, no matter what the
process does.
-
-
-
-
-
-
1 1
Quality Codes in Communication with OPC
In the communication via the "OPC" channel, the quality codes that the OPC does not support
are converted.
17.8.3
Quality Code in WinCC
Quality Code in OPC
0x48
0x40
0x4C
0x40
0x5C
0x40
0x60
0x40
0x80...0xD4
0xC0
0xD8
0xC0
Tag Status
Introduction
The tag status of individual WinCC tags can be monitored in Runtime. The tag status contains,
among other information, data regarding violations of the configured measurement range limits
as well as the status of linkage between WinCC and automation device.
418
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.8 Quality of Tags
The quality code informs of the quality of a tag independent of where this code was formed.
Thereby, the status of the entire value transfer and value processing are taken into
consideration.
For example, if a violation occurs of the measurement range at the lower limit, quality code
"0x55" is communicated. This violation of the measurement range might have occurred in the
WinCC data manager or in the field device. The tag status allows you to find out if this
measurement range violation occurred in WinCC or prior to passing the value to WinCC.
For example, if the tag status reports a limit violation with code 0x0010, it indicates that the
values remained below the lower range limit configured in WinCC. If the tag status does not
report any limit violation, the quality code passed on to WinCC already contained the limit
violation.
Evaluation of Quality Codes
Quality codes can be evaluated in a number of different ways:
● Evaluation with C scripts
● Evaluation through the dynamic dialog
● Evaluation of the "Quality Code Change Tag" result of an I/O field
WinCC Status Flags
Possible tag statuses are contained in the following table.
Name of flag
Value
Description
0x000 No error
0
DM_VARSTATE_NOT_ESTABLISH
ED
0x000 Connection to partner not established
1
DM_VARSTATE_HANDSHAKE_ER
ROR
0x000 Handshake error
2
DM_VARSTATE_HARDWARE_ERR 0x000 Network module defective
OR
4
DM_VARSTATE_MAX_LIMIT
0x000 Configured upper limit exceeded
8
DM_VARSTATE_MIN_LIMIT
0x001 Configured lower limit exceeded
0
DM_VARSTATE_MAX_RANGE
0x002 Format upper limit exceeded
0
DM_VARSTATE_MIN_RANGE
0x004 Format lower limit exceeded
0
DM_VARSTATE_CONVERSION_E
RROR
0x008 Display conversion error (in connection with format limit
0
xxx exceeded)
DM_VARSTATE_STARTUP_VALUE 0x010 Tag initialization value
0
DM_VARSTATE_DEFAULT_VALUE
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
0x020 Tag replacement value
0
419
Communication - Diagnostics
17.8 Quality of Tags
17.8.4
Name of flag
Value
DM_VARSTATE_ADDRESS_ERRO
R
0x040 Channel addressing error
0
Description
DM_VARSTATE_INVALID_KEY
0x080 Tag not found / not available
0
DM_VARSTATE_ACCESS_FAULT
0x100 Access to tag not permitted
0
DM_VARSTATE_TIMEOUT
0x200 Timeout / no check-back message from the channel
0
DM_VARSTATE_SERVERDOWN
0x400 Server not available.
0
Using the Tag Status to Monitor Connection Status
Introduction
The status of individual WinCC tags can be monitored in Runtime, providing information about
the status of the associated connection.
The monitoring is configured in Graphics Designer as an object property. One possibility for
monitoring would be to use the "Text" property of a static text.
In the shortcut menu of the "Dynamic" dialog for the desired property, select "Dynamic Dialog"
to open the "Dynamic value ranges" dialog.
420
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.8 Quality of Tags
The following settings are specified here:
● Tag to be monitored
● For tag value: assignment of validity range and status display
● The activation of the tag status evaluation
● For the status: assignment of validity range and corresponding status text
In Runtime, one of the entered status texts, which corresponds to the tag's current status, is
displayed in the configured object.
17.8.5
Monitoring Tag Status Using Global Actions
Introduction
One way to monitor the status of a tag is to make use the internal functions "GetTagState" and
"GetTagStateWait" in the Global Script editor. In contrast to the "GetTag" and "GetTagWait"
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
421
Communication - Diagnostics
17.8 Quality of Tags
functions, these not only return the tag's value but also its status. This status value can be
evaluated and then used to trigger various events. It can also be used to assess the status of
the associated connection.
In the global action, the status value of the monitored tag is determined using the "GetTagState"
function for this tag type. There is such a function for each tag type. The status value "0"
indicates a good connection with no errors. This status can now be evaluated as desired.
Example:
This example illustrates the monitoring of a WinCC tag of the type "Signed 16-Bit Value". The
"GetTagSWordState" function is used to determine the status of this tag. The first function
parameter is the name of the WinCC tag to be monitored. The second parameter gives where
the returned status value is to be written.
The tag status is output in the internal tag BINi_E_CONNECTION. In the event of an error, the
value of this tag is set to TRUE. In the error handling, the tag can, for example, be used to
trigger an alarm or display an error message.
17.8.6
How to Check an Internal Tag
Introduction
If an internal tag does not have the expected value in Runtime, you can use the following
procedure to check the tag.
422
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Communication - Diagnostics
17.8 Quality of Tags
Requirements
● Configure an internal tag.
● Activate the WinCC project.
Procedure
1. In WinCC Explorer in tag management, select the entry "Internal Tags".
2. In the data window, select the tag that you wish to check. To do this, open the directory
structure until the tag is displayed in the data window.
3. Move the mouse pointer over the tag to be checked. A tooltip window opens showing the
current tag value, the quality code and the last time that the value changed.
4. Check the quality code. If value "80" is displayed, the tag value is OK. A description of the
other values can be found under "Tag Quality Codes".
5. If the quality code is not equal to "80", select the tag in the tag management and click
"Properties" in the shortcut menu to open the "Tag Properties" dialog.
6. Check whether values have been configured for the upper or lower limits, or start he value
on the "Limits/Reporting" tab. These values can affect the display.
7. If the tag value is affected by one of the configured values, deactivate the project and
change the limit or substitute value.
Note
Tag values, quality codes etc. are only displayed in Runtime.
See also
Quality Codes of Tags (Page 414)
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
423
Index
B
as ActiveX Control, 374
Testing, 371
"
"MPI" channel unit, 217
Configuring the connection, 217
"Slot PLC" channel unit, 224
Configuring the connection, 224
"System Info" channel, 379
Diagnostic option, 379
5
505-Ethernet (CP 1413-x)
Channel Unit, 305
A
Adding a tag, 81, 88
Adding new drivers, 160
Address properties, 92, 107, 163, 165, 166, 171
Example for S5 Profibus FDL, 181
Address type
Mitsubishi Ethernet, 64
Addresses of tags, 309
TI Ethernet Layer 4, 309
AR_SENDAR_SEND-FunctioninWinCC , 242
AR_SEND-Function in WinCC
Configuring Variants for an Archive Tag, 269
Configuring Variants for Multiple Archive Tags,
272
Data Block,Structure and Parameters, 243
Example for Data Block Structure, 252, 253, 254,
259, 261, 263, 265, 268
Overview of the properties of the variants, 248
Variants for an Archive Tag, 250
Variants for Multiple Archive Tags, 255
Variants for Multiple Archive Tags (optimized),
267
AS data type, 17
Type conversion, 28
AS511, 185
Automation device, 158
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Bar
Example of System Info, 354
BinWrite Mechanism, 36
General Procedure, 36
Bit by bit access, 36, 138, 230
CCS7PlusChannel, 300
S5 AS511, 192
S5 Ethernet Layer 4, 138
S5 Profibus FDL, 163
S5 Serial 3964R, 201
S7 Protocol Suite, 230
TI Ethernet Layer 4, 310
TI Serial, 322
Bit/Byte access, 36
Bit-/Byte-tag, 38
Block, 178
Cyclic block, 178
Byte array, 171
Byte by byte access, 36, 140, 230
S5 AS511, 193
S5 Ethernet Layer 4, 140
S5 Profibus FDL, 165
S5 Serial 3964R, 202
S7 Protocol Suite, 232
SIMATIC S7-1200, S7-1500 Channel, 301
TI Ethernet Layer 4, 311
TI Serial, 323
C
CCS7PlusChannel
Configuring a tag with bit by bit access, 300
Channel, 15, 133, 195, 206, 409
check, 380, 391, 401
Configuring SIMATIC S5 PROFIBUS FDL, 160
Diagnosis of channels, 371
Example for S5 PROFIBUS FDL, 178
Mitsubishi Ethernet, (See Mitsubishi Ethernet)
PROFIBUS FMS, 123
SIMATIC S5 Ethernet Layer 4, 133
SIMATIC S5 Programmers Port AS511, 185
SIMATIC S5 Serial 3964R, 195
SIMATIC S7 Protocol Suite, 206
SIMATIC TI Ethernet Layer 4, 305
Status - Logical Connections function , 371
425
Index
Testing, 409
TI Serial, 317
Channel , 123
Channel diagnosis, 373
"System Info" channel, 379
Chanel with , 374, 376
Channel diagnosis, 373, 374, 375
Channel diagnosis as Windows application , 375
Channel diagnosis with , 374
Channel diagonsis, 371
Channel with Status - Logical Connections
function , 371
Checking configuration data, 408
Checking connection, 409
Checking internal tags, 422
Checking tag, 382, 393, 403, 411
Checking the configuration of the communication
processor, 387, 389, 397, 398
Configuring a the Trace function of a channel,
377
Connection parameters, 399
Diagnostic option, 379, 384, 395, 404
ERROR flag of logbook entry, 379, 384
Example, 421
Function , 371
INFO flag of logbook entry, 379, 384, 395, 404
Log file, 379, 384, 395, 404
Monitoring of tag status in dynamic dialog, 420
Monitoring of tag status with global actions, 421
OPC channel, 404
Overview of status messages, 409
PROFIBUS system parameters, 390
Properties - CP5613, 387, 389, 397, 398
SIMATIC S5 PROFIBUS FDL channel, 395
SIMATIC S7 Protocol Suite channel, 384
Standard flags of the Trace function, 377
Status - Logical Connections, 371
System parameters, 399
Testing channel, 409
WinCC channel diagnosis, 409
Channel Diagnosis
Channel diagnosis with , 373
Checking connection, 380, 391, 401
Overview of status messages, 380, 391, 401
Testing channel, 380, 391, 401
WinCC channel diagnosis, 380, 391, 401
Channel diagnosis channel
Testing, 374, 376
Channel diagnosis Channel Diagnose
Channel diagnosis Channel Diagnose , 375
Channel diagnosis with Channel Diagnose , 374
Channel Diagnosis trace file , 373
426
Channel Unit, 15, 133, 160, 207
505 Serial Unit #1, 317
505-Ethernet (CP 1413-x), 305
Connection parameters, 307
FDL (CP5412/A2-1), 160
Industrial Ethernet, 214
MPI, 217
Named Connections, 219
PROFIBUS, 222
PROFIBUS-FMS, 125
S5 Transport (CP1413-x), 135
S5 Transport (TCP/IP), 135
S5-AS511, 185, 187
S5-RK512 (3964R), 195
Selection for SIMATICS7ProtocolSuiteS7
Protocol Suite channel:Selecting the channel unit,
207
Slot PLC, 224
Soft PLC, 226
System parameters, 144, 168, 236, 313
TCP/IP, 227
Channel unit FDL (CP5412/A2-1), 155, 160
Channel Unit Industrial Ethernet, 214
Configuring the connection, 215
Channel units
Mitsubishi Ethernet, (See Mitsubishi Ethernet)
Communication, 13
Addressing in the automation system, 17
AS data type, 20, 28
Basis, 13
BinWrite Mechanism, 36
Bit-/Byte-access, 36
Bit-/Byte-tag, 38
Channel Unit, 15
Communication between WinCC and Automation
systems, 15
Communication driver, 15
Configuring a tag with BinWrite, 38
Configuring powertags, 20
Connection, 15
Connection properties, 19
Creating a new connection, 19
Data type, 17, 28
Length definition for text tags, 17
Linear scaling of numerical tag types, 17
PowerTag, 17
Principle of the BinWrite-Mechanism, 36
Principle of WinCC communication, 15
Sorting format adaptation by AS data type, 28
Sorting format adaptation by WinCC data type,
22
Tag Properties, 20
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Index
Type conversion, 28
Type Conversion, 17
Value range, 28
WinCC data types, 17
WinCC process communication, 15
WinCC Type Conversion, 17
Communication driver, 15, (See channel)
Communication processor, 387, 389, 397, 398
Checking the configuration of the communication
processor, 387, 389, 397, 398
Communication type, 173
Configuring, 173
Configuration data, 408
Configure bit by bit access
Tag, 310
Configure byte by byte access
Tag, 311
Configuring
Tag, 309
TI Ethernet Layer 4, 307
Configuring a tag
TI Ethernet Layer 4, 309
Configuring a tag with bit by bit access
TI Ethernet Layer 4, 310
Configuring a tag with byte by byte access
TI Ethernet Layer 4, 311
Connection, 15, 213, 409
Active connection, 155
check, 380, 391, 401
Configuring, 162, 215, 217, 220, 222, 224, 226,
228
Creating a connection, 81
Creating a new connection, 19
Passive connection, 155
Testing, 409
Testing configuration of connection, 390, 399
Connection Monitoring, 86
Connection parameters, 15, 135, 160, 162, 173, 175,
213, 399
Channel Unit, 307
PROFIBUS FMS, 123
S5 AS511, 185, 187
S5 Ethernet Layer 4, 133
S7 Protocol Suite, 206
SIMATIC S5 Serial 3964R, 195
TI Ethernet Layer 4, 305, 307
TI Serial, 317
Connection properties, 19, 162, 173, 175
Counter, 344
CP1434 TF, 313, 315
CPU load, 344
Example of System Info, 355
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Cyclic Read Services, 237
D
Data area, 157
Data transmission, 173
Configuring a passive data transfer, 175
Configuring an active data transfer, 173
Data type, 17, 85, 211, 296, 344
Data types used, 344, 351
Mitsubishi Ethernet, 60, 64
S5 AS511, 186
S5 Profibus FDL, 157
S5 Serial 3964R, 196
S7 Protocol Suite, 211
SIMATIC S7-1200, S7-1500 Channel, 296
Supported WinCC data types, 85
Supported WinCC data types overview, 85
TI Ethernet Layer 4, 306
Type conversion, 28
Data Types, 17, 134
PROFIBUS FMS, 123, 124
S5 Ethernet Layer 4, 134
TI Ethernet Layer 4, 306
Date, 344
Daylight Saving/Standard Time, 243
Device Name, 144, 168, 313
change, 169
TI Ethernet Layer 4, 313
Diagnosis
Channels, 337
Diagnostic option, 379, 384, 395, 404
"System Info" channel, 379
OPC channel, 404
SIMATIC S5 PROFIBUS FDL channel, 395
SIMATIC S7 Protocol Suite channel, 384
Disk capacity, 344
Example of System Info, 354
Free dive capacity, 344, 349
E
ERROR flag, 379, 384
Example:, 421
F
Filter criteria, 88
427
Index
I
I/O field
Example of System Info, 352
I/O Field
Example for S5 Profibus FDL, 181
INFO flag, 379, 384, 395, 404
L
Life beat monitoring for channel S5Seral3964R
Life beat monitoring , 197
Log file, 379, 384, 395, 404
Logbook entry, 379, 384, 395, 404
Logbook file, 373
Logical Device Name, 236
modify, 240
M
MELSEC FX3U series, (See Mitsubishi Ethernet)
MELSEC Q series, (See Mitsubishi Ethernet)
Message
Example of System Info, 356, 358
Message text, 356
Mitsubishi Ethernet, 59
Address types, 64
Channel units, 59, 61, 63
Configure connections, 61, 63
Configuring a tag, 61, 64, 66
Controllers that are supported, 61
Data types, 60, 64
Tag, 66
Multi-user system, 363
Use of channel , 363
N
Named Connections channel unit, 219
Configuring the connection, 220
Network, 13
New connection, 88
Numerical tag type, 17
Linear Scaling, 17
O
OPC
Access to tag, 87
428
Adding a tag, 81, 88
Address properties, 92, 107
Channel diagnosis, 404
Configuring access to a WinCC tag with the OPC
Item Manager, 88
Configuring access to a WinCC tag without the
OPC Item Manager, 92, 107
Configuring an OPC channel on a WinCC OPC DA
client, 88
Configuring structure, 95
Configuring structure tag, 95
Creating a connection, 81
Error handling in event of disturbed OPC
communication, 97, 117
Filter criteria, 88
Functionality of the WinCC OPC DA Client, 86
Functionality of the WinCC OPC UA client, 110
Functionality of the WinCC OPC XML client, 102
New connection, 88
OPC in WinCC, 79
OPC Item Manager, 81
OPC1, 92, 107
OPCServer.WinCC-(DPC_4001), 88
Overview of OPC Item Manager functions, 81
Querying of ProgID, 81
Structure properties, 95
Supported WinCC data types, 85
Supported WinCC data types overview, 85
Tag selection, 81
Using structures on a WinCC OPC DA client, 94,
96
WinCC as an OPC DA client, 79, 97
WinCC as OPC UA client, 117
WinCC as OPC XML client, 79
OPC channel, 404
Configuring an OPC channel on a WinCC OPC DA
client, 88
Diagnostic option, 404
OPC communication, 97, 117
Error handling in the event of disturbed OPC DA
communication, 97
Handling errors in OPC UA communication, 117
OPC DA client, 86
Functionality of the WinCC OPC DA Client, 86
OPC Item Manager, 81, 88
Overview of OPC Item Manager functions, 81
OPC UA
Access to tag, 110
OPC UA client, 110
Functionality of the WinCC OPC UA client, 110
OPC XML
Access to tag, 103
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Index
OPC XML client, 102
Functionality of the WinCC OPC XML client, 102
OPC1, 92, 107
OPCServer.WinCC-(DPC_4001), 88
P
Point of error, 356
Printer monitoring, 344
Example of System Info, 359
Process picture
Example of System Info, 367
PROFIBUS Channel Unit, 222
Configuring the connection, 222
PROFIBUS FMS, 123
Addresses of tags, 129, 130
Configuring a tag, 129, 130
Connection parameters, 125
Data Types, 124
PROFIBUS FMS Channel Unit, 125, 126, 128
PROFIBUS FMS communication driver
PROFIBUSFMS , 123
PROFIBUS system parameters, 390
ProgID, 81
Querying of ProgID, 81
Properties - CP5613, 387, 389, 397, 398
Q
Quality codes of tags, 412, 414
R
Raw Data Tag, 171, 275
as byte array, 171, 276
Configuring, 171
Configuring as a byte array, 277
Configuring for BSEND/BRCV functions, 282
for BSEND/BRCV functions, 279
S
S5 AS511, 187
Configuring, 187
Configuring a tag, 189
Configuring a tag with bit by bit access, 192
Data Types, 186
Defining a tag with byte by byte access, 193
Tag address, 189
S5 Ethernet Layer 4, 133
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Configuring, 135
Configuring a tag, 137
Configuring a tag with bit by bit access, 138
Configuring a tag with byte by byte access, 140
Configuring a tag with word by word access, 141
Connection parameters, 135
Data Types, 134
Device Name, 144, 145
Error codes during connection disturbances, 148
iNA960 messages, 151
Internal error codes and constants, 148
Raw Data Tag, 143
SCI messages, 152
System parameters of the channel unit, 144
Tag address, 137
Transport Parameter, 144, 146
S5 Profibus FDL, 155
Access to a S5 tag of data type ARRAY OF BYTE,
157
Access to a S5 tag of data type BIT, 157
Access to a S5 tag of data type BYTE, 157
Access to S5 tags, 157
Active connection, 155
Adding new drivers, 160
Address properties, 163, 165, 166, 171
Block, 178
Changing the device name, 169
Changing write/read monitoring time, 170
Channel diagnosis, 395
Channel unit FDL (CP5412/A2-1), 155
Configuring a passive data transfer, 175
Configuring a raw data tag, 171
Configuring a tag, 163
Configuring a tag with bit by bit access, 163
Configuring a tag with byte by byte access, 165
Configuring a tag with word by word access, 166
Configuring an active data transfer, 173
Configuring channel SIMATIC S5 Profibus FDL,
160
Configuring data handling blocks, 178
Configuring SIMATIC S5 Profibus FDL, 160
Configuring the communication type, 173
Configuring the connection, 162
Connection parameters, 160, 162, 173, 175
Connection properties, 162, 173, 175
Cyclic block, 178
Data area, 157
Data type, 157
Device Name, 168
Example, 178, 181
Features of the channel, 158
Passive connection, 155
429
Index
Raw data tag as byte array, 171
Service Access Point, 155
Special function, 171
Startup block, 178
supported data type, 157
System parameters, 169, 170
System parameters of the channel unit, 168
Tag parameter, 160
Tag Properties, 163, 165, 166, 171
Type conversion, 158
Write/Read monitoring time, 168
S5 Serial 3964R, 195
Configuring, 197
Configuring a tag, 199
Configuring a tag with bit by bit access, 201
Configuring a tag with byte by byte access, 202
Data type of the tags, 196
S5 tag, 157
Access to a S5 tag of data type ARRAY OF BYTE,
157
Access to a S5 tag of data type BIT, 157
Access to a tag of data type byte, 157
Access to S5 tags, 157
S7 Protocol Suite, 206
AR_SEND variant for an archive tag, 250
AR_SEND variant for multiple archive tags, 255
AR_SEND variant for multiple archive tags
(optimized), 267
Changing logical device names, 240
Channel diagnosis, 384
Channel Unit, 207, 213
Configuring, 212
Configuring a raw data tag as a byte array, 277
Configuring a tag with bit by bit access, 230
Configuring a tag with byte by byte access, 232
Configuring a tag with word by word access, 233
Configuring a text tag, 234
Configuring an AR_SEND variant for an archive
tag, 269
Configuring an AR_SEND variant for multiple
archive tags, 272
Configuring software redundancy, 289
Configuring system parameters, 238
Configuring the connection, 215, 217, 220, 222,
224, 226, 228
Configuring the raw data tag for the BSEND/BRCV
functions, 282
Cyclic Read Services, 237
Data exchange with FB
S7ProtocolSuite:AR_SEND variants , 242
Data type, 211
Delete Software Redundancy in WinCC, 292
430
Error codes during connection disturbances, 293
Example for Data Block Structure AR_SEND, 252,
253, 254, 259, 261, 263, 265, 268
Overview of the properties of the AR_SEND
variants, 248
Raw Data Tag, 275
Raw data tag as byte array, 276
Raw data tag for BSEND/BRCV functions, 279
Software Redundancy, 283
Software Redundancy - Connection-specific
internal tags, 285
Structure and Parameter of Data Block in
AR_SEND Function, 243
supported data type, 211
System parameters, 236
Service Access Point, 155
SIMATIC S5 Profibus FDL, 155
Raw Data Tag, 171
S5 Profibus FDL, 155
Special function, 171
SIMATIC S5 PROFIBUS FDL channel, 395
Diagnostic option, 384
SIMATIC S5 Programmers Port AS511, 185
SIMATIC S5 Serial 3964R, 195
SIMATIC S5 Serial 3964R , 197
SIMATIC S7 Protocol Suite, 206
SIMATIC S7 Protocol Suite channel, 384
Diagnostic option, 384
SIMATIC S7-1200, S7-1500 Channel
Configuration, 297
Configuring a tag with byte by byte access, 301
Configuring a tag with word by word access, 302
Configuring a text tag, 303
Configuring the connection, 297
Data type, 296
SIMATIC TI Ethernet Layer 4, 305
Channel, 305
Transport Parameter, 313
SIMOTION channel, 325
Configuring, 327, 328, 329, 331, 332
Data types, 326
Diagnosis, 337
System parameters, 333, 335
Soft PLC channel unit, 226
Configuring the connection, 226
Software Redundancy, 283
configure in WinCC, 289
Connection-specific internal tags, 285
delete in WinCC, 292
Special function, 171
Standard flag, 377
Startup block, 178
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Index
Status - Logical Connections functionStatus - Logical
Connection, 371
Status display, 380, 391, 401, 409
Example of System Info, 359
Structure
Configuring structure, 95
Using structures on a WinCC OPC DA client, 94
Using WinCC OPC client, 96
Structure properties, 95
Structure tag, 95
Configuring structure tag, 95
Supported system information, 344
Overview, 344
System Info, 342
Bar configuration, 354
Channel diagnosis, 379
Configuring, 350
Data types used, 351, 364
Differences to other software components, 349
Example, 351, 364, 367, 368
Example:, 352, 354, 355, 356, 358, 359, 365, 366
Free dive capacity, 344
I/O field configuration, 352
Message text, 356
Overview of supported system information, 344
Overview of the Supported System Information,
344
Point of error, 356
Status display configuration, 359
Tag to be monitored, 356
System Info System information
Use in multi-user system , 363
System parameters, 15, 144, 236, 333, 335, 399
Channel Unit, 313
Configuring, 238, 240
S5 Ethernet Layer 4, 133
S5 Profibus FDL, 155
SIMATIC S7 Protocol Suite, 206
TI Ethernet Layer 4, 305, 313, 315
T
Tag, 17, 137, 351, 411, 412
Adding a tag, 81
Addressing external tags in the automation
system, 17
Checking internal tags, 422
Configure bit by bit access, 138, 163, 201, 310,
322
Configure byte by byte access, 140, 165, 202, 311,
323
Configuring, 129, 130, 137, 163, 309, 321
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Configuring a tag with BinWrite, 38
Configuring a text tag, 20
Configuring external tags, 20
Configuring linear scaling, 20
Configuring OPC Item Manager, 88, 92
Configuring PC Item Manager, 107
Configuring powertags, 20
Configuring tag addresses , 199
Configuring word by word access, 141, 166
Example of System Info, 351, 366
External, 17
Length definition for text tags, 17
OPC Item Manager, 88
PowerTag, 17
Quality, 412
Quality code, 412
Quality codes, 414
Status, 412, 418
Tag selection, 81
Testing, 382, 393, 403, 411
Testing configuration of tags, 390, 399
Tag address, 137
PROFIBUS FMS, 123, 124, 129, 130
S5 Ethernet Layer 4, 133
TI Serial, 317
Tag Properties, 20, 163, 165, 166, 171
Example for S5 Profibus FDL, 181
Tag status, 412, 418, 420, 421
Monitoring of tag status in dynamic dialog, 420
Monitoring of tag status with global actions, 421
Tag to be monitored, 356
TCP/IP channel unit, 227
Configuring the connection, 228
Text Tag, 17, 230
Configuring, 20, 234
TI Ethernet Layer 4, 305
Addresses of tags, 309
Bit by bit access, 310
Byte by byte access, 311
Configuring, 307
Configuring a tag, 309
Configuring a tag with bit by bit access, 310
Configuring a tag with byte by byte access, 311
Connection parameters, 305, 307
Data type, 306
Data Types, 306
Device Name, 313
System parameters, 305, 313, 315
Transport Parameter, 313
TI Serial, 317
Addresses of tags, 321
Configuring, 319
431
Index
Configuring a tag, 321
Configuring a tag with bit by bit access, 322
Configuring a tag with byte by byte access, 323
Connection parameters, 319
Data Types, 318
Tag address, 321
Time, 344, 349
Example of System Info, 352
Time stamp, 243
Timer, 344
Trace function, 377
Configuring, 377
Transferring Changes, 237
Transport Parameter, 15, 144
SIMATIC S5 Ethernet Layer 4, 144
SIMATIC TI Ethernet Layer 4, 313
TI Ethernet Layer 4, 313
TTY interface, 185
Type conversion, 28, 158
Type Conversion, 17
V
Value range, 28
Variable, 230
Configure bit by bit access, 230
Configure byte by byte access, 232
Configuring word by word access, 233
W
WinAC Basis, 226
WinAC Pro, 224
WinCC
as OPC DA client, 79, 97
as OPC UA client, 117
as OPC XML client, 79
OPC in WinCC, 79, 97, 117
WinCC channel diagnosis, 380, 391, 401, 409
WinCC Communication, 15
General Procedure, 15
WinCC Data type, 17, 22
Type conversion, 22, 28
WinCC Data type, 22
WinCC process communication, 15
WinCC Type Conversion, 17
Word by word access, 230
S7 Protocol Suite, 233
SIMATIC S7-1200, S7-1500 Channel, 302
Write/Read monitoring time, 168, 170
change, 170
432
WinCC: Communication
System Manual, 02/2013, A5E32318638-AA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement