dpa series
DPA Series
DPA Series
··
··
··
··
··
··
··
··
··
DPA
DPA
DPA
DPA
DPA
DPA
DPA
DPA
DPA
4120
4140
4410
4411
4245
4260
8150
8225
8412
51
DPA Series
The new models of the DPA
8000 series are based on highly
efficient Class D platforms and
offer in addition to outstanding
audio performance features such
as integrated automatic breakdown switchover, integrated
electronics for the connection of
multiple loudspeaker lines per
amplifier channel, an additional
audio input, etc.
The Promatrix 8000 system, to
which the DPA 8000 amplifiers
also belong, sets new standards in
the integration of event, information
and evacuation sound reinforcement.
In the development of the DPA
8000 series, the emphasis was
upon the following primary characteristics: smaller dimensions coupled
with greater power, lower power
consumption, higher integration
of functions, and better audio performance. The outcome is a series
of models that meet the highest
demands of modern sound reinforce-
ment systems including evacuation
conformity. With a signal-to-noise
ratio of over 102 dB, the amplifiers
can be used without compromise
for pro sound applications.
Thanks to the permanent integrated
supervision, faults not only in the
amplifiers themselves but also in
the loudspeaker lines connected
are detected and reported immediately. For the supervision of the
loudspeaker lines, a choice is offered
of various methods, which can be
used singly or in combination.
The total power of 500 W in two
rack units is achieved with minimal
power dissipation, which means
savings, too, on external air conditioning.
Each of the amplifiers possesses
an additional audio input for the
playing of background music or
use as an emergency input. For the
connection of multiple loudspeaker
lines to a single amplifier channel,
the control electronics are already
integrated into the amplifier and
can be extended through the DCS
400 modular system.
It goes without saying that power
can be drawn either from the
mains or a battery and that all
devices offer power up current
limiting as well as additional protective circuitry.
German development. Manufactured using the BPS (Bosch
Production System) in Straubing,
Germany.
Features DPA 8000 Series:
• 3 models with 1 x 500 W,
2 x 250 W, 4 x 125 W
• Mains and 24V battery operation
• Lower power consumption
• Compact 2U format
• Power up current limiting
• Integrated breakdown switchover
• Integrated zone switching
• Protective circuits
• Status LEDs
53
PowerH Series
PowerH 5000
PowerH Series
technical specifications
General
H 2500
2Ω
Load Impedance
H 5000
4Ω
8Ω
2Ω
4Ω
8Ω
Maximum Midband Output Power, 1 kHz, THD=1%
2000 W
1450 W
850 W
3500 W
2500 W
1500 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
-
1200 W
600 W
-
2100 W
1050 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
2400 W
1700 W
940 W
4500 W
3200 W
1800 W
Max. Single Channel Output Power Continuous, 1kHz
2050 W
1600 W
900 W
4100 W
2700 W
1600 W
-
3800 W
2900 W
-
7000 W
5000 W
Maximum Bridged Output Power 1 kHz, THD=1%
95 V
Maximum RMS Voltage Swing 1 kHz, THD=1%
125 V
10 Hz ... 50 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
39 dB / 35 dB / 32 dB (switchable)
41dB / 35 dB / 32 dB (switchable)
0 dBu / +4 dBu / +7 dBu (switchable)
0 dBu / +6 dBu / +9 dBu (switchable)
THD at rated output power MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.05 %
DIM 30, 3.15 kHz, 15 kHz
< 0.02 %
+22 dBu (9,76 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
< 10 Hz ... 30 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor ,1kHz
> 400
Slew Rate
30 V/µs
35V/µs
Signal to Noise Ratio Amplifier A-weighted, 32 dB constant gain
109 dB
111 dB
< -70 dBu
Output Noise , A-weighted
Class-H Grounded Bridge
Output Stage Topology
Power Requirements
100 V - 240 V, 50 Hz - 60 Hz; 100 V, 50 Hz - 60 Hz
Power Consumption at 1/8 maximum output power @ 4 Ω
1000 W
Protections
1450 W
Audio limiters, High temperature, DC, HF, Short Circuit, Back-EMF, Peak current
limiters, Inrush current limiters,Turn-on Delay, Mains Circuit Breaker Protection,
Mains Over / Undervoltage Protection
Cooling
Ambient Temperature Limits
Front-to-Rear, 5-stage-fans
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 498
Dimensions (WxHxD), mm
Weight
14.2 kg (31.1 lbs)
14.5 kg (32.0 lbs)
Amplifier at rated conditions, both channels driven with 8 Ω loads, unless otherwise specified
55
Xa 4000
Xa 4000
technical specifications
General
Load Impedance
Maximum Midband Output Power, THD=1%, 80Hz SUB, 1 kHz
TOP, Single Channel
Rated Output Power,
THD <0.1%, 20 Hz-140 Hz SUB, 140 Hz-20 kHz TOP Single
Channel
Maximum RMS Voltage Swing,
THD=1%, 80 Hz SUB, 1 kHz TOP
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
Voltage Gain ref. 1 kHz
Input Sensitivity
at rated output power, 1 kHz
THD at rated output power, MBW=80kHz, 1 kHz
Max. Input Level
SUB
TOP
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
1800 W
1100 W
600 W
1600 W
900 W
500 W
-
1000 W
500 W
-
800 W
400 W
78 V
10 Hz ... 50 kHz
37.3 dB
0 dBu (0.775 V rms)
< 0.05 %
+22 dBu (9.76 Vrms)
Input Inpedance, active balanced
20 kΩ
Damping Factor ,1kHz
> 300
Slew Rate
30 V/µs
Signal to Noise Ratio, A-weighted
102 dB
Output Stage Topology
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Protections
Cooling
Ambient Temperature Limits
Safety Class
Class-H
240 V, 230 V, 220 V, 120 V or 100 V, 50 Hz... 60 Hz (factory configured)
850 W
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current
limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
+5°C ... +40°C (40°F ... 105°F)
I
Dimensions (WxHxD), mm
483 x 88.1 x 384
Weight
8.25 kg (18.2 lbs)
Optional Accesories:
Rear Rackmount 15.5“: D112 930 (RMS15-CL)
Rear Rackmount 18.0“: D112 933 (RMS18-CL)
Xa 4000
56
LX Series
LX 2200
LX Series
technical specifications
General
LX 1600
LX 2200
LX 3000
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
1300 W
800 W
500 W
1600 W
1100 W
600 W
2100 W
1500 W
900 W
-
700 W
350 W
-
900 W
450 W
-
1200 W
600 W
Max. Single Channel Output
Power Dynamic-Headroom, IHF-A
2200 W
1200 W
625 W
2600 W
1400 W
720 W
2900 W
1800 W
1000 W
Max. Single Channel Output
Power Continuous, 1kHz
1700 W
1000 W
550 W
2100 W
1300 W
660 W
2600 W
1700 W
950 W
-
2600 W
1600 W
-
3200 W
2200 W
-
4200 W
3000 W
Load Impedance
Maximum Midband Output Power,
1 kHz, THD=1%
Rated Output Power,
20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power
1 kHz, THD=1%
Maximum RMS Voltage Swing
1 kHz, THD=1%
72 V
78 V
10 Hz ... 60 kHz
Power Bandwidth, THD=1%, ref.
1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated
output power @ 8Ω, 1 kHz
+4.7 dBu (1.33 V rms)
+5.8 dBu (1.51 V rms)
THD at rated
output power MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.02 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
< -80 dB
Crosstalk, ref. 1 kHz at
rated output power
Frequency Response, ref. 1 kHz
15 Hz ... 40 kHz (- 1dB)
Input Inpedance, active balanced
20 kΩ
> 300
Damping Factor ,1kHz
Slew Rate
30 V/µs
Signal to Noise Ratio, A-weighted
107 dB
38V/µs
107 dB
108 dB
100 V, 120V, 220V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
Power Requirements
625 W
850 W
1070 W
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
Cooling
+5°C ... +40°C (40°F ... 105°F)
Ambient Temperature Limits
I
Safety Class
483 x 88.1 x 384
Dimensions (WxHxD), mm
Weight
35V/µs
Class-H
Output Stage Topology
Protections
+7.0 dBu (1.74 V rms)
+22 dBu (9.76 Vrms)
Max. Input Level
Power Consumption at 1/8 maximum output power @ 4 Ω
95 V
7.8 kg (17.2 lbs)
8.15 kg (18.0 lbs)
8.7 kg (19.2 lbs)
Optional Accesories:
Rear Rackmount 15.5“: D112 930 (RMS15-CL)
Rear Rackmount 18.0“: D112 933 (RMS18-CL)
LPN + Lo-Cut Filter: D112963 (NRS 90268)
57
CL Series
CL Series
technical specifications
General
Load Impedance
CL 800
2Ω
CL 1200
4Ω
8Ω
2Ω
4Ω
8Ω
Maximum Midband Output Power, 1 kHz, THD=1%
600 W
400 W
240 W
900 W
600 W
350 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
-
300 W
150 W
-
500 W
250 W
Max. Single Channel Output Power
Dynamic-Headroom, IHF-A
1100 W
580 W
300 W
1450 W
850 W
450 W
Max. Single Channel Output Power Continuous, 1kHz
800 W
480 W
270 W
1200 W
720 W
410 W
-
1200 W
800 W
-
1800 W
1200 W
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
50 V
62 V
10 Hz ... 60 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+1.15 dBu (0.88 V rms)
+3.2 dBu (1.12 V rms)
THD at rated output power MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.02 %
DIM 30, 3.15 kHz, 15 kHz
< 0.01 %
+22 dBu (9,76 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
15 Hz ... 40 kHz (- 1dB)
Input Inpedance, active balanced
20 kΩ
> 300
Damping Factor, 1kHz
25 V/µs
30 V/µs
Signal to Noise Ratio, A-weighted
103.5 dB
105.5 dB
Output Stage Topology
Class-AB
Class-H
Slew Rate
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Protections
100 V, 120V, 220V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
600 W
Front-to-Rear, 3-stage-fans
Cooling
+5°C ... +40°C (40°F ... 105°F)
Ambient Temperature Limits
I
Safety Class
483 x 88.1 x 386.8
Dimensions (WxHxD), mm
Weight
Optional Accesories:
Rear Rackmount 15.5“: D112 930 (NRS90262)
Rear Rackmount 18.0“: D112 933 (NRS90264)
LPN + Lo-Cut Filter: D112963 (NRS 90268)
58
500 W
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters,
Turn-on delay
13.5 kg (29.8 lbs)
15 kg (33.0 lbs)
CL Series
CL 1600
General
CL 1600
CL 2000
2Ω
4Ω
8Ω
2Ω
4Ω
Maximum Midband Output Power, 1 kHz, THD=1%
1100 W
800 W
500 W
1500 W
1000 W
600 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
-
700 W
350 W
-
850 W
450 W
Max. Single Channel Output Power
Dynamic-Headroom, IHF-A
2200 W
1200 W
625 W
2700 W
1450 W
750 W
Max. Single Channel Output Power Continuous, 1kHz
1500 W
950 W
550 W
1900 W
1150 W
650 W
-
2200 W
1600 W
-
3000 W
2000 W
Load Impedance
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
72 V
80 V
10 Hz ... 60 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+4.7 dBu (1.33 V rms)
+5.5 dBu (1.46 V rms)
THD at rated output power MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.02 %
DIM 30, 3.15 kHz, 15 kHz
< 0.01 %
+22 dBu (9.76 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
15 Hz ... 40 kHz (- 1dB)
Input Inpedance, active balanced
20 kΩ
> 300
Damping Factor, 1kHz
Slew Rate
35 V/µs
Signal to Noise Ratio, A-weighted
107 dB
Power Consumption at 1/8 maximum output power @ 4 Ω
Protections
109 dB
100 V, 120V, 220V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
660 W
725 W
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters,
Turn-on Delay
Front-to-Rear, 3-stage-fans
Cooling
+5°C ... +40°C (40°F ... 105°F)
Ambient Temperature Limits
I
Safety Class
483 x 88.1 x 386.8
Dimensions (WxHxD), mm
Weight
35 V/µs
Class-H
Output Stage Topology
Power Requirements
8Ω
16 kg (35.3 lbs)
18.2 kg (39.7 lbs)
Optional Accesories:
Rear Rackmount 15.5“: D112 930 (NRS90262)
Rear Rackmount 18.0“: D112 933 (NRS90264)
LPN + Lo-Cut Filter: D112963 (NRS 90268)
59
SL Series
SL Series
technical specifications
General
SL 900
SL 1200
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
650 W
450 W
270 W
900 W
600 W
380 W
-
400 W
200 W
-
500 W
250 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
1150 W
660 W
350 W
1700 W
950 W
480 W
Max. Single Channel Output Power Continuous, 1kHz
850 W
540 W
310 W
1200 W
750 W
420 W
1300 W
900 W
-
1800 W
1200 W
Load Impedance
Maximum Midband Output Power, 1 kHz, THD=1%, Dual Channel
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
-
55.3 V
65.1 V
10 Hz ... 30 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+2.2 dBu (1.0 V rms)
+3.1 dBu (1.11 V rms)
< 0.03 %
THD at rated output power MBW=80kHz, 1 kHz
IMD-SMPTE, 60 Hz, 7 kHz
< 0.1 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
+21 dBu (8.69 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
10 Hz ... 40 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz
> 300
Slew Rate
25 V/µs
26 V/µs
Signal to Noise Ratio, A-weighted
106 dB
107 dB
Output Noise, A-weighted
< -71 dBu
Output Stage Topology
Class-AB
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Mains Fuse
Protections
Cooling
Ambient Temperature Limits
100 V, 120V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
550 W
700 W
240V / 230V: T10AH,
120V / 100V: T20AH
240V / 230V: T12AH,
120V / 100V: T25AH
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush
current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 421.5
Dimensions (WxHxD), mm
Weight
Optional Accesories:
2-Way crossover, internal filter card, 24dB, LR
330Hz (NRS 90249), 500Hz (NRS 90250)
800Hz (NRS 90251), 1200Hz (NRS 90252)
60
12.6 kg (27.8 lbs)
14.8 kg (32.6 lbs)
SL Series
SL 1200
General
SL 1800
SL 2400
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
1250 W
900 W
550 W
1800 W
1200 W
750 W
-
800 W
400 W
-
1100 W
550 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
2450 W
1400 W
700 W
3400 W
1800 W
950 W
Max. Single Channel Output Power Continuous, 1kHz
1700 W
1100 W
630 W
2400 W
1500 W
850 W
2800 W
1800 W
-
3600 W
2400 W
Load Impedance
Maximum Midband Output Power, 1 kHz, THD=1%, Dual Channel
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
-
78.8 V
90.6 V
10 Hz ... 30 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+5.1 dBu (1.39 Vrms)
+6.6 dBu (1.66 Vrms)
< 0.03 %
THD at rated output power MBW=80kHz, 1 kHz
IMD-SMPTE, 60 Hz, 7 kHz
< 0.1 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
+21 dBu (8.69 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
10 Hz ... 40 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz
> 300
Slew Rate
27 V/µs
30 V/µs
Signal to Noise Ratio, A-weighted
109 dB
110 dB
< -71 dBu
Output Noise, A-weighted
Class-H
Output Stage Topology
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Mains Fuse
Protections
Cooling
Ambient Temperature Limits
100 V, 120V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
700 W
850 W
240V / 230V: T15AH,
120V / 100V: T25AH
240V / 230V: T15AH,
120V / 100V: T30AH
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush
current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 421.5
Dimensions (WxHxD), mm
Weight
16.3 kg (35.9 lbs)
17.7 kg (39.0 lbs)
Optional Accesories:
2-Way crossover, internal filter card, 24dB, LR
330Hz (NRS 90249), 500Hz (NRS 90250)
800Hz (NRS 90251), 1200Hz (NRS 90252)
61
DSA Series - Multi-Channel
DSA Series - Multi-Channel
technical specifications
General
DSA 8405
DSA 8805
2Ω
4Ω
8Ω
70 V /
10Ω
100 V /
20Ω
2Ω
4Ω
8Ω
70 V /
10Ω
100 V /
20Ω
Maximum Midband Output
Power, 1 kHz, THD=1%,
4 channels driven
500 W
500 W
250 W
VLD:500 W
500 W
500 W
500 W
500 W
250 W
VLD:500 W
500 W
500 W
Rated Output Power,
20 Hz ... 20 kHz, THD <0.3%, 4
channels driven
450 W
450 W
225 W
VLD:450 W
450 W
450 W
450 W
450 W
225 W
VLD:450 W
450 W
450 W
-
1000 W
1000 W
1000 W /
20 Ω
1000 W /
40 Ω
-
1000 W
1000 W
1000 W
/ 20 Ω
1000 W
/ 40 Ω
70 V
100 V
32 V
45 V
70 V
100 V
0.775 V
(+0.0 dBu)
1.1 V
(+3.0 dBu)
Load Impedance
Maximum Bridged Output Power
1 kHz, THD=1%
Maximum RMS Voltage Swing
1 kHz, THD=1%
Input Sensitivity,
rated power, 1 kHz
32 V
45 V
0.775 V
(+0.0 dBu)
1.1 V
(+3.0 dBu)
1.55 V
(+6.0 dBu)
10 Hz ... 25 kHz
Power Bandwidth, THD=1%,
ref. 1kHz, half power @ rated load
50 Hz ... 25 kHz
32 dB
Voltage Gain ref. 1 kHz
33 dB
10 Hz ... 25 kHz
36 dB
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.05 %
DIM 30, 3.15 kHz, 15 kHz
< 0.02 %
15 Hz ... 30 kHz (± 1dB)
Frequency Response,
ref. 1 kHz, 8 Ω load
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz, 8 Ω
> 240
28 V/µs
Slew Rate
98 dB
100 dB
104 dB
106 dB
98 dB
100 dB
104 dB
106 dB
< -66 dBu
< -65 dBu
< -65 dBu
< -64 dBu
< -66 dBu
< -65 dBu
< -65
dBu
< -64
dBu
Class-D
Output Stage Topology
Power Requirements
Power Consumption
at 1/8 maximum output
Protections
220-240V, 50-60 Hz or 120 V, 50-60 Hz or 100 V, 50-60 Hz
490 W
Front-to-Rear, temperature controlled fans
+5 °C...+40 °C (40 °F...105 °F)
Ambient Temperature Limits
I
Safety Class
481 x 88.0 x 421
Dimensions (WxHxD), mm
62
930 W
Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains
Circuit Breaker Protection, Mains Over/Undervoltage Protection
Cooling
Weight
36 dB
< -80 dB
Crosstalk,
ref. 1 kHz at rated output power
Output Noise, A-weighted
33 dB
+22 dBu (9.76 Vrms)
Max. Input Level
Signal to Noise Ratio, A-weighted
50 Hz ... 25 kHz
32 dB
THD at rated output power
MBW=80kHz, 1 kHz
1.55 V
(+6.0 dBu)
11.1 kg (24.3 lbs)
13.9 kg (28.7 lbs)
DSA Series - Multi-Channel
DSA 8805
General
DSA 8410
2Ω
4Ω
8Ω
70 V /
5Ω
100 V /
10Ω
Maximum Midband Output Power, 1 kHz, THD=1%, 4 channels driven
1000 W
1000 W
500 W
VLD:1000 W
1000 W
1000 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.3%, 4 channels driven
900 W
900 W
450 W
VLD:900 W
900 W
900 W
-
2000 W
2000 W
2000 W / 10 Ω
2000 W /20 Ω
70 V
100 V
Load Impedance
Maximum Bridged Output Power
1 kHz, THD=1%
Maximum RMS Voltage Swing
1 kHz, THD=1%
Input Sensitivity, rated power, 1 kHz
45 V
63 V
1.1 V
(+3.0 dBu)
1.55 V
(+6.0 dBu)
1.55 V
(+6.0 dBu)
10 Hz ... 25 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ rated load
50 Hz ... 25 kHz
32 dB
Voltage Gain ref. 1 kHz
33 dB
THD at rated output power
MBW=80kHz, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.05 %
< 0.02 %
DIM 30, 3.15 kHz, 15 kHz
+22 dBu (9.76 Vrms)
Max. Input Level
Crosstalk, ref. 1 kHz at rated output power
< -80 dB
Frequency Response, ref. 1 kHz, 8 Ω load
15 Hz ... 30 kHz (± 1dB)
20 kΩ
Input Inpedance, active balanced
> 240
Damping Factor, 1kHz, 8 Ω
28 V/µs
Slew Rate
Signal to Noise Ratio, A-weighted
Output Noise, A-weighted
Output Stage Topology
101 dB
103 dB
104 dB
106 dB
< -66 dBu
< -65 dBu
< -65 dBu
< -64 dBu
Class-D
Power Requirements
220-240V, 50-60 Hz or 120 V, 50-60 Hz or 100 V, 50-60 Hz
Power Consumption
at 1/8 maximum output
840 W
Protections
Cooling
Ambient Temperature Limits
Safety Class
36 dB
Audio Limiters, High Temperature, DC, HF, Short Circuit, Peak Current Limiters, Inrush Current
Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/Undervoltage Protection
Front-to-Rear, temperature controlled fans
+5 °C...+40 °C (40 °F...105 °F)
I
Dimensions (WxHxD), mm
481 x 88.0 x 421
Weight
11.1 kg (24.3 lbs)
63
DSA Series - Dual-Channel
DSA Series - Dual-Channel
technical specifications
General
DSA 8204
DSA 8206
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
650 W
450 W
270 W
900 W
600 W
380 W
-
400 W
200 W
-
500 W
250 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
1150 W
660 W
350 W
1700 W
950 W
480 W
Max. Single Channel Output Power Continuous, 1kHz
850 W
540 W
310 W
1200 W
750 W
420 W
-
1300 W
900 W
-
1800 W
1200 W
Load Impedance
Maximum Midband Output Power, 1 kHz, THD=1%, Dual Channel
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
55.3 V
65.1 V
10 Hz ... 30 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+2.2 dBu (1.0 V rms)
+3.1 dBu (1.11 V rms)
< 0.03 %
THD at rated output power MBW=80kHz, 1 kHz
IMD-SMPTE, 60 Hz, 7 kHz
< 0.1 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
+21 dBu (8.69 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
10 Hz ... 40 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz
> 300
Slew Rate
25 V/µs
26 V/µs
Signal to Noise Ratio, A-weighted
106 dB
107 dB
Output Noise, A-weighted
< -71 dBu
Output Stage Topology
Class-AB
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Mains Fuse
Protections
100 V, 120V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
550 W
700 W
240V / 230V: T10AH,
120V / 100V: T20AH
240V / 230V: T12AH,
120V / 100V: T25AH
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters,
Inrush current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
Cooling
Ambient Temperature Limits
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 421.5
Dimensions (WxHxD), mm
Weight
12.6 kg (27.8 lbs)
14.8 kg (32.6 lbs)
Remote Power On
Power remote via switch, delay time selectable
Signal Processing
Lo-Cut 50Hz / 18dB, switchable
Optional Accesories:
2-Way crossover, internal filter card, 24dB, LR
330Hz (NRS 90249), 500Hz (NRS 90250)
800Hz (NRS 90251), 1200Hz (NRS 90252)
64
DSA Series - Dual-Channel
DSA 8212
General
DSA 8209
DSA 8212
2Ω
4Ω
8Ω
2Ω
4Ω
8Ω
1250 W
900 W
550 W
1800 W
1200 W
750 W
-
800 W
400 W
-
1100 W
550 W
Max. Single Channel Output Power Dynamic-Headroom, IHF-A
2450 W
1400 W
700 W
3400 W
1800 W
950 W
Max. Single Channel Output Power Continuous, 1kHz
1700 W
1100 W
630 W
2400 W
1500 W
850 W
-
2800 W
1800 W
-
3600 W
2400 W
Load Impedance
Maximum Midband Output Power, 1 kHz, THD=1%, Dual Channel
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%
Maximum Bridged Output Power 1 kHz, THD=1%
Maximum RMS Voltage Swing 1 kHz, THD=1%
78.8 V
90.6 V
10 Hz ... 30 kHz
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω
32 dB
Voltage Gain ref. 1 kHz
Input Sensitivity at rated output power @ 8Ω, 1 kHz
+5.1 dBu (1.39 Vrms)
+6.6 dBu (1.66 Vrms)
< 0.03 %
THD at rated output power MBW=80kHz, 1 kHz
IMD-SMPTE, 60 Hz, 7 kHz
< 0.1 %
DIM 30, 3.15 kHz, 15 kHz
< 0.05 %
+21 dBu (8.69 Vrms)
Max. Input Level
< -80 dB
Crosstalk, ref. 1 kHz at rated output power
Frequency Response, ref. 1 kHz
10 Hz ... 40 kHz (± 1dB)
Input Inpedance, active balanced
20 kΩ
Damping Factor, 1kHz
> 300
Slew Rate
27 V/µs
30 V/µs
Signal to Noise Ratio, A-weighted
109 dB
110 dB
< -71 dBu
Output Noise, A-weighted
Class-H
Output Stage Topology
Power Requirements
Power Consumption at 1/8 maximum output power @ 4 Ω
Mains Fuse
Protections
100 V, 120V, 230V, 240V, 50 Hz... 60 Hz (factory configured)
700 W
850 W
240V / 230V: T15AH,
120V / 100V: T25AH
240V / 230V: T15AH,
120V / 100V: T30AH
Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters,
Inrush current limiters,Turn-on delay
Front-to-Rear, 3-stage-fans
Cooling
Ambient Temperature Limits
+5°C ... +40°C (40°F ... 105°F)
I
Safety Class
483 x 88.1 x 421.5
Dimensions (WxHxD), mm
Weight
16.3 kg (35.9 lbs)
17.7 kg (39.0 lbs)
Remote Power On
Power remote via switch, delay time selectable
Signal Processing
Lo-Cut 50Hz / 18dB, switchable
Optional Accesories:
2-Way crossover, internal filter card, 24dB, LR
330Hz (NRS 90249), 500Hz (NRS 90250)
800Hz (NRS 90251), 1200Hz (NRS 90252)
65
PCL Series
PCL Series
technical specifications
PCL 1125T
General
PCL 1415
PCL 1245
PCL 1240T
8Ω
4Ω
8Ω
4Ω
8Ω
4Ω
Max. Midband Output
(THD < 0.2 %, 20 Hz…20 kHz)
100 W
160 W
300 W
480 W
215 W
430 W
430 W
Rated Output Power
(THD < 0.2 %, 20 Hz…20 kHz)
75 W
150 W
225 W
450 W
200 W
400 W
400W
Load Impedance
100 V
70 V
50 V
4
2
Max. RMS Voltage Swing
(THD = 1 %, 1 kHz)
32.1 V
44.7 V
44.7 V
117 V
82 V
59 V
Voltage Gain (at 1 kHz)
30 dB
34.3 dB
34.3 dB
42.2 dB
39.1 dB
36.2 dB
545 W
-
-
Channels
Power Handling (at 1/8 max. output power, limited pink)
-
385 W
-
2
530W
< 10 Hz – 40 kHz
65 Hz – 40 kHz
> 20 kΩ
Input Impedance
(20 Hz…20 kHz symmetr.)
> 250
Damping Factor
(at 100 Hz / 1 kHz, 4 Ω)
Signal to Noise Ratio S/N (A-weighted)
101 dB
> 250
104 dB
103 dB
audio limiters, thermal overload, peak current limiters, power-on delay
Protection
front to rear
Cooling
I
Safety Class
483 x 88 x 405 mm, 19” / 2 HU
Dimensions (WxHxD), mm
66
-
230 V / 50 Hz – 60 Hz
Power Requirements
Weight
-
< 0.1 %
THD (MBW = 80 kHz, 1 kHz)
Frequency Response
(-1 dB, ref. 1 kHz)
0 dBu (775 mV)
Input Sensitivity
(at ROP or Voltage, 1 kHz)
18 kg
16.5 kg
26 kg
PCL Series
PCL 1415
General
PCL 1225T
8Ω
4Ω
Max. Midband Output
(THD < 0.2 %, 20 Hz…20 kHz)
135 W
270 W
Rated Output Power
(THD < 0.2 %, 20 Hz…20 kHz)
125 W
250 W
Load Impedance
100 V
PCL 1125T
70 V
50 V
100 V
270 W
250 W
40 Ω
50 V
270 W
250 W
19.6 Ω
250 W
10 Ω
250 W
40 Ω
250 W
19.6 Ω
2
Channels
70 V
250 W
40 Ω
1
Max. RMS Voltage Swing
(THD = 1 %, 1 kHz)
35.4 V
117 V
82 V
59 V
117 V
82 V
59 V
Voltage Gain (at 1 kHz)
32.2 dB
42.2 dB
39.1 dB
36.2 dB
42.2 dB
39.1 dB
36.2 dB
-
-
170 W
-
-
Power Handling (at 1/8 max. output power, limited pink)
-
-
330 W
0 dBu (775 mV)
Input Sensitivity
(at ROP or Voltage, 1 kHz)
< 0.1 %
THD (MBW = 80 kHz, 1 kHz)
65 Hz – 40 kHz
Frequency Response
(-1 dB, ref. 1 kHz)
> 20 kΩ
Input Impedance
(20 Hz…20 kHz symmetr.)
Damping Factor
(at 100 Hz / 1 kHz, 4 Ω)
Signal to Noise Ratio S/N (A-weighted)
> 250
103 dB
audio limiters, thermal overload, peak current limiters, power-on delay
front to rear
Cooling
I
Safety Class
Dimensions (WxHxD), mm
Weight
103 dB
230 V / 50 Hz – 60 Hz
Power Requirements
Protection
-
483 x 88 x 405 mm, 19” / 2 HU
23.5 kg
16.5 kg
67
DPA 4000 Series
DPA 4000 Series
technical specifications
General
Load Impedance
Rated Output Power (Mains)
DPA 4410
DPA 4120
DPA 4140
100 Ω / 100 V, 50 Ω / 70 V
25 Ω / 50 V, 4 Ω / 20 V
DPA 4411
50 Ω / 100 V, 25 Ω / 70 V
12.5 Ω / 50 V, 4 Ω / 28 V
25 Ω / 100 V, 12.5 Ω / 70 V
6.25 Ω / 50 V, 4 Ω / 40 V
4 x 100 W
(acc. to IEC 268-3 / 19.4)
2 x 200 W configurable
1 x 200 W + 2 x 100 W configurable
200 W
(acc. to IEC 268-3 / 19.4)
400 W
(acc. to IEC 268-3 / 19.4)
balanced, floating
Power Output Characteristics
balanced
Input Characteristics
Input Sensitivity
775 mV / 0 dBu
Input Impedance
≥ 10 kΩ
≤1%
Distortion @ 1 kHz and Nom. Outp. Power
≤ 1.2 mV / -56 dBu
Interference Voltage (A)
60 Hz .. 20 kHz
Frequency Response
600 Ω
Load Impedance (monitor)
2 V / + 8.2 dBu
Nominal Output Voltage (monitor)
Output Characteristics (monitor)
unbalanced
electronically balanced
Class-AB, Transformer, Floating
Output Stage Topology
115 V / 230 V AC, ±10 % / 50 - 60 Hz or 24 V DC, -10 / +30 %
Power Requirements
Mains Power Consumption
1010 VA at nominal output
520 VA at nominal output
1020 VA at nominal output
377 VA driven at -10 dB
200 VA driven at -10 dB
380 VA driven at -10 dB
30 VA no signal
44 VA no signal
18 A at nominal output
9.1 A at nominal output
17.3 A at nominal output
7.5 A driven at -10 dB
3.7 A driven at -10 dB
7.1 A driven at -10 dB
0.4 A no signal / 2.5 mA in
stand-by
0.6 A no signal / 2.5 mA in
stand-by
62 VA no signal
24 V DC Power Consumption
1.0 A no signal / 2.5 mA in
stand-by
67 VA no signal
1.1 A no signal / 2.5 mA in
stand-by
High Temperature, Inrush Current Limiters, Short Circuit
Protection
Front-to-Rear, temperature controlled
Cooling
+5° C ... +40° C (40° F... 105° F)
Ambient Temperature Limits
I
Safety Class
483 x 132 x 345 mm, 19” / 3 HU
Dimensions (WxHxD), mm
340 mm
Installation Depth without Connectors
max. 410 mm
Installation Depth including Connectors
Weight
22.3 kg
22.5 kg
Optional
13.2 kg
16.7 kg
anthracite
Color
Extension-kits for the DPA 4410 / DPA 4411:
NRS 90206 Pilot Tone Monitoring (for four amplifiers)
NRS 90207 Ground-Fault Monitoring (for four amplifiers)
NRS 90227 Output Transformer (floating, balanced monitor
outputs) for DPA 4411
Additional Version DPA 4411:
DPA 4411N: DPA 4411 + NRS 90206 + NRS 90207
Extension-kits for the DPA 4120 / DPA 4140:
NRS 90222 Remote module (note: not supplied with the DPA
4120/DPA 4140)
NRS 90224 Pilot tone & ground-fault monitoring (note: not
supplied with the DPA 4120/DPA 4140)
NRS 90225 Standard input module (note: not supplied with the
DPA 4120/DPA 4140)
NRS 90227 Output transformer (floating, balanced monitor
output)
Additional Version DPA 4140:
DPA 4140N: DPA 4140 + NRS 90222 + NRS 90224
68
DPA 4000 Series
DPA 4411
General
Load Impedance
Rated Output Power
Maximum Output Power
Output Power in Bridged-Operation
DPA 4245
DPA 4260
28.5 Ω / 100V
20 Ω / 100V
14 Ω / 70 V
9.8 Ω / 70 V
1.8 Ω / 25 V
1.25 Ω / 25 V
4 Ω / 37.4 V
4 Ω / 44.7 V
350 W (acc. to IEC 268-3 / 19.4)
500 W (acc. to IEC 268-3 / 19.4)
450 W into 4 Ω
600 W into 4 Ω
700 W (acc. to IEC 268-3)
1000 W (acc. to IEC 268-3)
balanced, floating
Power Output Characteristics:
electronically balanced
Input Characteristics:
775 mV / 0 dBu
Input Sensitivity
Input Impedance
20 kΩ
Distortion @ 1kHz and Nom. Outp. Power
≤ 0.1 %
Frequency Response
45 Hz .. 22 kHz (-3 dB)
Signal to Noise Ratio
> 100 dB
Class-AB, Transformer, Floating
Output Stage Topology
230 V AC / 50 - 60 Hz
Power Requirements Mains
Mains Power Consumption
Protection
Cooling
1714 VA at nominal output
2268 VA at nominal output
635 VA driven at -10 dB
842 VA driven at -10 dB
78 VA no signal
131 VA no signal
audio limiter, thermal overload, DC, HF, Back-EMF, peak current limiter, initial
current inrush limiter, power-on delay,
saturation limitation for output transformers
Front-to-Rear, temperature controlled
+5° C ... +40° C (40° F... 105° F)
Ambient Temperature Limits
I
Safety Class
Dimensions (WxHxD), mm
483 x 132.5 x 384 mm, 19” / 3 HU
377 mm
Installation Depth without Connectors
max. 437 mm
Installation Depth including Connectors
Weight
Color
Optional
20.5 kg
22.5 kg
anthracite
Extension-kits for the DPA 4245 / DPA 4260:
NRS 90208 Input transformer (for one input)
69
DPA 8000 Series
DPA 8000 Series
technical specifications
General
Load Impedance
DPA 8150
50 V / 5 Ω
50 V
70 V
30.2 dB
33.1 dB
THD at rated output power MBW=80kHz, 1kHz
< 0.5 %
IMD-SMPTE, 60Hz, 7kHz
< 2.0 %
DIM 30, 3,15kHz, 15kHz
Max. Input Level
< 0.2 %
< -80 dB
Frequency Response, ref. 1 kHz, rated load
50 Hz...20kHz
Input Impedance, active balanced
20 k Ω
Signal to Noise Ratio, A-weighted
> 102 dB
Power Requirements
Power Consumption, at rated Output Power
Monitor
- rated Output Voltage
- rated Load Impedance
CAN
Control Port
Protection
Cooling
Ambient Temperature Limits
Safety Class
Dimensions (WxHxD), mm
Weight
70
36.2 dB
6.15 V (18 dBu)
Crosstalk, ref. 1 kHz at rated output power
Output Stage Topology
100 V
1.55 V (6 dBu)
Input Sensitivity, rated power @ rated load, 1kHz
Voltage Gain ref. 1kHz
100 V / 20 Ω
500 W
Rated Output Power, 1kHz, THD < 0.5%
Rated RMS Voltage Swing, 1kHz, THD=1%
70 V / 9.8 Ω
Class-D, Transformer, Floating
115 V / 230 V AC (-10% / +6%), 50-60 Hz or 24 V DC (-10% / +30%)
990 W (Mains) / 900 W (Battery)
1.3 V (4.5 dBu)
600 Ω
10...500 kBit/s, 2 x RJ-45
1 x 8-pole Euro Block, 3 Control Inputs/Outputs
2 Reference Outputs (15 V, 100 mA/GND), 1 Ready/Fault Output
Audio Limiters, High Temperature, DC, Short Circuit, Mains Over / Undervoltage Protection,
DC Supply Undervoltage Protection, Inrush Current Limiter, Ground Fault
Front-to-Rear, temperature controlled fans
-5 °C .. +45 °C
Class I
483 x 88 x 376 mm, 19” / 2 HE
16 kg
DPA 8000 Series
DPA 8412
General
Load Impedance
DPA 8225
50 V / 10 Ω
70 V / 19.6 Ω
50 V
50 V / 20 Ω
70 V
100 V
50 V
30.2 dB
33.1 dB
36.2 dB
< 2.0 %
DIM 30, 3,15kHz, 15kHz
< 0.2 %
30.2 dB
36.2 dB
< 1.0 %
< 0.1 %
Crosstalk, ref. 1 kHz at rated output power
< -80 dB
Frequency Response, ref. 1 kHz, rated load
50 Hz...20kHz
Input Impedance, active balanced
20 k Ω
Signal to Noise Ratio, A-weighted
> 102 dB
Class-D, Transformer, Floating
Output Stage Topology
115 V / 230 V AC (-10% / +6%), 50-60 Hz or 24 V DC (-10% / +30%)
990 W (Mains) / 900 W (Battery)
Power Consumption, at rated Output Power
Monitor
- rated Output Voltage
- rated Load Impedance
1.3 V (4.5 dBu)
600 Ω
10...500 kBit/s, 2 x RJ-45
CAN
1 x 8-pole Euro Block, 3 Control Inputs/Outputs
2 Reference Outputs (15 V, 100 mA/GND), 1 Ready/Fault Output
Audio Limiters, High Temperature, DC, Short Circuit, Mains Over / Undervoltage Protection,
DC Supply Undervoltage Protection, Inrush Current Limiter, Ground Fault
Front-to-Rear, temperature controlled fans
Cooling
-5 °C .. +45 °C
Ambient Temperature Limits
Class I
Safety Class
483 x 88 x 376 mm, 19” / 2 HE
Dimensions (WxHxD), mm
Weight
33.1 dB
6.15 V (18 dBu)
Max. Input Level
Protection
100 V
< 0.5 %
IMD-SMPTE, 60Hz, 7kHz
Control Port
70 V
1.55 V (6 dBu)
THD at rated output power MBW=80kHz, 1kHz
Power Requirements
100 V / 80 Ω
125 W
Input Sensitivity, rated power @ rated load, 1kHz
Voltage Gain ref. 1kHz
70 V / 39,2 Ω
250 W
Rated Output Power, 1kHz, THD < 0.5%
Rated RMS Voltage Swing, 1kHz, THD=1%
DPA 8412
100 V / 40 Ω
16 kg
18 kg
71
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement