HD-DA-2 - Special
HD-DA-2
1-to-2 HDMI® Distribution Amplifier & Audio Converter
Do you need to feed two video displays from one HDMI source? Or, split
an HDMI signal between a display and a surround sound processor? Need
to break out the HDMI audio signal and convert it to SPDIF or analog?
Or, merge separate digital audio and video sources into one HDMI
stream? Not a problem—just use the HD-DA-2.
The HD-DA-2 from Crestron® provides a versatile HD AV signal problem
solver with high-performance specs and set-and-forget simplicity.
HDMI Signal Splitter
As an HDMI distribution amp, the HD-DA-2 lets you easily share one
HDMI signal between two display devices, or split that signal to feed
one display and a separate audio processor. Ideal for use with Blu-ray
Disc™ and multimedia computer sources, the HD-DA-2 supports
high-definition video up to 1080p60 with Deep Color, as well as
high-resolution computer signals up to 1920x1200. It also handles
high-bitrate 7.1 surround sound audio formats like Dolby® TrueHD and
DTS-HD Master Audio™.
HDMI Audio Extractor
In addition to its two HDMI outputs, the HD-DA-2 also includes a SPDIF
coaxial digital audio output and a stereo analog audio output,
allowing the audio signal to be extracted from the HDMI source and
converted to feed a legacy audio device. The SPDIF output supports
surround sound signals up to 6.1, while the analog output handles
stereo 2-channel signals.
HDMI Audio Embedder
The HD-DA-2 also provides SPDIF coaxial and optical digital audio
inputs, either of which may be selected as the audio source in place
of the incoming HDMI audio signal. This allows any HDMI video signal
to be merged with an alternate audio source, effectively letting you
generate a new HDMI AV signal containing your choice of audio and
video sources. The HDMI input can even accept the signal from a DVI
digital video source[1], allowing separate DVI and SPDIF signals to
be merged into one HDMI signal, perfect for integrating an older
digital AV source or computer into a modern HDMI based system.
1-to-4 Audio Distribution
All of the outputs on the HD-DA-2 can be used simultaneously to feed
up to four separate devices. The surround sound format for all outputs
is simply limited to the best common format supported by the selected
input and outputs. For instance, if you are using the analog output,
which only supports stereo 2-channel signals, then the HDMI and SPDIF
outputs will be limited to 2-channel PCM. If you'd like to distribute
Dolby Digital® or DTS® 5.1 surround sound via the SPDIF output, then
the HDMI outputs will be limited to 5.1 as well and the analog output
will be disabled entirely. Eight-channel PCM and high-bitrate 7.1
formats like Dolby TrueHD and DTS-HD Master Audio can only be handled
by HDMI, so naturally all the other inputs and outputs on the HD-DA-2
must be disabled in order to pass the highest quality formats.
Reliable Performance with Simple Setup
Configuring the HD-DA-2 for each application requires just a quick
setting of its DIP switches. The switches provide a simple yet
versatile means for selecting the audio input source, configuring
EDID, and choosing which audio formats to allow.
Embedded in every HDMI signal, EDID (Extended Display Identification
Data) allows a display or audio processor to inform the upstream
source about its format and resolution capabilities, enabling the
www.crestron.com
800.237.2041
source to configure itself to deliver an optimum signal to the
downstream device. The HD-DA-2 provides extra measures to ensure
optimum results when distributing HDMI to multiple destinations,
letting the installer select which output device provides the EDID, or
letting the HD-DA-2 determine the best common resolution and format
that both devices can support. It also allows the audio EDID to be
controlled independent of the video, even letting the installer
manually limit the audio format based on the inputs and outputs in
use.
Reliability is further enhanced by allowing the installer to limit the
number of HDCP (High-bandwidth Digital Content Protection) keys to
match the capabilities of the source, ensuring the core system remains
functional in the event too many devices get connected.
> Provides a high-performance one in, two out HDMI signal
splitter
> Enables extracting analog and SPDIF audio signals from
the
HDMI source
> Enables embedding SPDIF audio (coax or optical) onto the
HDMI outputs
> Allows merging DVI and SPDIF audio sources into one
HDMI
signal
> Supports 1080p w/Deep Color and 7.1 channel HD lossless
audio
> Compatible with DVI and DisplayPort Multimode[1]
> Allows versatile configuration of EDID and HDCP key
handling
> Includes HDMI signal and HDCP status indicators
> No programming or control system required
> Ideal for portable or fixed installation use
HD-DA-2
SPECIFICATIONS
Video
Input Signal Types: HDMI, DVI[1], DisplayPort Multimode[1]
Output Signal Types: HDMI, DVI[1]
Formats: HDMI w/Deep Color, DVI, HDCP content protection support
Input Resolutions, Progressive: [email protected], [email protected] (480p),
[email protected] (576p), [email protected], [email protected], [email protected],
[email protected], [email protected], [email protected], [email protected],
[email protected] (720p50), [email protected] (720p60), [email protected],
[email protected], [email protected], [email protected], [email protected],
[email protected], [email protected], [email protected], [email protected],
[email protected], [email protected], [email protected], [email protected]
(1080p24), [email protected] (1080p25), [email protected] (1080p50),
[email protected] (1080p60), [email protected], [email protected],
[email protected], plus any other resolution allowed by HDMI up to 165MHz
pixel clock
Input Resolutions, Interlaced: [email protected] (480i), [email protected] (576i),
[email protected] (1080i25), [email protected] (1080i30), plus any other
resolution allowed by HDMI up to 165MHz pixel clock
Output Resolutions: Matched to inputs
Audio
Switcher: 3x1 digital switch
Input Signal Types: HDMI, DisplayPort Multimode[1], SPDIF coaxial, SPDIF
optical (TOSLINK)
Output Signal Types: HDMI, SPDIF coaxial, analog 2-channel
Formats, HDMI & SPDIF: Dolby Digital®, Dolby Digital EX, DTS®, DTS-ES,
DTS 96/24, 2ch PCM
Formats, HDMI only: Dolby Digital Plus, Dolby® TrueHD, DTS-HD High Res,
DTS-HD Master Audio™, Up to 8ch PCM
Formats, Analog: Stereo 2-channel
Digital-To-Analog Conversion: 24-bit 48 kHz
Performance (analog): Frequency Response: 20Hz to 20kHz ±1dB
S/N Ratio: >70dB, 20Hz to 20kHz A-weighted
THD+N: <0.2% @ 1kHz
Stereo Separation: >60dB
Communications
USB: For console, USB 2.0 client
HDMI: Passes CEC, provides EDID and HDCP key management
Connectors - Top
AUDIO IN, OPTICAL: (1) JIS F05 female (TOSLINK) optical fiber connector;
S/PDIF optical digital audio input
AUDIO IN, SPDIF: (1) RCA female;
S/PDIF coaxial digital audio input;
Input Impedance: 75 Ohms
AUDIO OUT, SPDIF: (1) RCA female;
S/PDIF coaxial digital audio output;
Output Impedance: 75 Ohms
AUDIO OUT, R - L: (2) RCA female;
Unbalanced stereo line-level audio output;
Maximum Output Level: 2 Vrms;
Output Impedance: 100 Ohms nominal
Connectors - Bottom
HDMI IN: (1) 19-pin Type A HDMI female;
HDMI digital video/audio input;
Also supports DVI and DisplayPort Multimode[1]
HDMI OUT 1 - 2: (2) 19-pin Type A HDMI female;
HDMI digital video/audio outputs;
Also supports DVI[1]
COMPUTER: (1) USB Type B female;
USB 2.0 computer console port
PWR 24 VDC 0.21A: (1) 2.1mm barrel DC power jack;
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
HDMI OUT 1 - 2: (2) red/green dual-color LEDs, green indicates presence of
a non-HDCP signal, red indicates presence of an HDCP signal
PWR 24 VDC 0.21A: (1) green LED, indicates 24 Volts DC power supplied
from power pack
Power Requirements
Power Pack: 0.21 Amps @ 24 Volts DC;
100-240 Volts AC, 50/60 Hz power pack, model PW-2407WU included
Environmental
Temperature: 32° to 104°F (0° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 18 BTU/Hr
Enclosure
Chassis: Metal, black finish, with (2) integral mounting flanges
Mounting: Freestanding, surface mount, or attach to a single rack rail
Dimensions
Height: 4.53 in (115 mm)
Width: 7.21 in (183 mm)
Depth: 1.24 in (32 mm)
Weight
1.1 lb (0.50 kg)
Available Models
HD-DA-2: 1-to-2 HDMI® Distribution Amplifier & Audio Converter
Included Accessories
PW-2407WU Wall Mount Power Pack 24VDC, 0.75A, Universal [Included
Quantity: 1]
Available Accessories
CBL-HD-1.5: Crestron® Certified HDMI® Interface Cable, 1.5 ft
CBL-HD-3: Crestron® Certified HDMI® Interface Cable, 3 ft
CBL-HD-6: Crestron® Certified HDMI® Interface Cable, 6 ft
CBL-HD-12: Crestron® Certified HDMI® Interface Cable, 12 ft
CBL-HD-20: Crestron® Certified HDMI® Interface Cable, 20 ft
CBL-HD-30: Crestron® Certified HDMI® Interface Cable, 30 ft
CBL-DP-HD-1.5: Crestron® Certified DisplayPort to HDMI® Interface Cable,
1.5 ft
CBL-DP-HD-3: Crestron® Certified DisplayPort to HDMI® Interface Cable, 3
ft
CBL-DP-HD-6: Crestron® Certified DisplayPort to HDMI® Interface Cable, 6
ft
CBL-DP-HD-12: Crestron® Certified DisplayPort to HDMI® Interface Cable,
12 ft
CBL-DP-HD-20: Crestron® Certified DisplayPort to HDMI® Interface Cable,
20 ft
CBL-DP-HD-30: Crestron® Certified DisplayPort to HDMI® Interface Cable,
30 ft
CBL-HD-DVI-1.5: Crestron® Certified HDMI® to DVI Interface Cable, 1.5 ft
CBL-HD-DVI-3: Crestron® Certified HDMI® to DVI Interface Cable, 3 ft
CBL-HD-DVI-6: Crestron® Certified HDMI® to DVI Interface Cable, 6 ft
CBL-HD-DVI-12: Crestron® Certified HDMI® to DVI Interface Cable, 12 ft
CBL-HD-DVI-20: Crestron® Certified HDMI® to DVI Interface Cable, 20 ft
CBL-HD-DVI-30: Crestron® Certified HDMI® to DVI Interface Cable, 30 ft
CBL-RCA-1.5: Crestron® Certified RCA Composite Video and S/PDIF Audio
Interface Cable, 1.5 ft
CBL-RCA-3: Crestron® Certified RCA Composite Video and S/PDIF Audio
Interface Cable, 3 ft
HD-DA-2
CBL-RCA-6: Crestron® Certified RCA Composite Video and S/PDIF Audio
Interface Cable, 6 ft
CBL-RCA-12: Crestron® Certified RCA Composite Video and S/PDIF Audio
Interface Cable, 12 ft
CBL-RCA2-1.5: Crestron® Certified RCA Stereo Audio Interface Cable, 1.5 ft
CBL-RCA2-3: Crestron® Certified RCA Stereo Audio Interface Cable, 3 ft
CBL-RCA2-6: Crestron® Certified RCA Stereo Audio Interface Cable, 6 ft
CBL-RCA2-12: Crestron® Certified RCA Stereo Audio Interface Cable, 12 ft
MP-WP140-B: Media Presentation Wall Plate - DVI-I w/Mini-TRS Stereo
Audio, Black
MP-WP140-W: Media Presentation Wall Plate - DVI-I w/Mini-TRS Stereo
Audio, White
MP-WP150-B: Media Presentation Wall Plate - HDMI® w/Mini-TRS Stereo
Audio, Black
MP-WP150-W: Media Presentation Wall Plate - HDMI® w/Mini-TRS Stereo
Audio, White
MP-WP152-B: Media Presentation Wall Plate - HDMI®, Black
MP-WP152-W: Media Presentation Wall Plate - HDMI®, White
MP-WP160-B: Media Presentation Wall Plate - DisplayPort w/Mini-TRS
Stereo Audio, Black
MP-WP160-W: Media Presentation Wall Plate - DisplayPort w/Mini-TRS
Stereo Audio, White
MP-WP162-B: Media Presentation Wall Plate - DisplayPort, Black
MP-WP162-W: Media Presentation Wall Plate - DisplayPort, White
Notes:
1. HDMI IN requires an appropriate adapter or interface cable to
accommodate a DVI or DisplayPort Multimode signal. HDMI OUT requires an
appropriate adapter or interface cable to accommodate a DVI signal.
CBL-HD-DVI and CBL-DP-HD interface cables available separately.
This product may be purchased from an authorized Crestron dealer. To find a
dealer, please contact the Crestron sales representative for your area. A
list of sales representatives is available online at www.crestron.
com/salesreps or by calling 800-237-2041.
Crestron is a registered trademark of Crestron Electronics, Inc. Blu-ray
Disc is a trademark of the Blu-ray Disc Association. Dolby, Dolby Digital,
and the double-D symbol are trademarks or registered trademarks of Dolby
Laboratories. DTS is a registered trademark & the DTS logos and Symbol are
trademarks of DTS, Inc. HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries. Other trademarks
and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims
proprietary interest in the marks and names of others.
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
HDMI Multi-Purpose Tool
HD-DA-2
Crestron Electronics, Inc. 15 Volvo Drive | Rockleigh, NJ 07647
Tel: 800.237.2041 / 201.767.3400 | Fax: 201.767.1905
www.crestron.com
All brand names, product names and trademarks are the property of their respective owners.
©2011 Crestron Electronics, Inc.
Specifications subject to change without notice. 3/18/2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement