traceable® humidity/thermometer remote sensor module

traceable® humidity/thermometer remote sensor module
TRACEABLE
SPECIFICATIONS
Humidity range:
Humidity resolution:
Humidity accuracy:
Temperature range:
Temperature resolution:
Temperature accuracy:
RF Transmission frequency:
Channels:
RF Transmission range:
Temperature sampling rate:
Power:
Size:
Weight:
®
HUMIDITY/THERMOMETER REMOTE SENSOR MODULE INSTRUCTIONS
5% to 95%RH
1%
±2% RH mid-range to ±4% RH elsewhere
–58.0 to 158.0°F (–50.0 to 70.0°C)
0.1°C
±1°C
433 MHz
3
30 meters
40-seconds
(2) AAA 1.5V alkaline batteries
2-1/3 x 3½ x ¾ inches
3 ounces
MAIN FEATURES
A. Two-line LCD
Displays the current temperature and
humidity monitored by the remote unit
Temperature display
Humidity display
Comfort-level indicator
B. LED INDICATOR
Flashes when the remote unit transmits a reading
C. °C/°F SLIDE SWITCH
Selects between Celsius (°C and Fahrenheit (°F)
D. CHANNEL SLIDE SWITCH
Designates the remote unit Channel 1 - Channel 2
or Channel 3
E. RESET BUTTON
Returns all settings to default values
F. BATTERY COMPARTMENT
Accommodates two UM-4 or AAA size alkaline batteries
G. BATTERY DOOR
H. WALL-MOUNT HOLDER
Supports the remote unit in wall-mounting
I. REMOVABLE TABLE STAND
For standing the remote unit on a flat surface
GETTING STARTED
Note: To ensure proper reception between the main unit
and the remote sensor, follow the instructions carefully.
BATTERY AND CHANNEL INSTALLATION
1.
Place both units as close as possible to each other.
2.
Remove the screws on the battery door of the remote
unit.
3.
Assign a different channel to each remote sensor by changing the channel
switch in the battery compartment of the remote sensor. (FIG A)
4.
Select the units of measurement for the temperature display on the °C/°F slide
switch. (FIG B)
5.
Install 2 alkaline batteries (UM-4 or “AAA size 1.5V) strictly according to the
polarity shown. (FIG C)
6.
Invest batteries or press the reset button of the main unit. Follow the instructions
as set out in the User’s manual.
7.
Replace the battery compartment door and secure its screws.
8.
Position the remote sensor and main unit within effective transmission range,
which in usual circumstances, is 30 meters.
Note: The effective range may be limited by building materials and the position of
either the main unit or remote sensors. Try various set-up arrangements for best
results.
Though the sensor is weatherproof, and is meant for use outside, it should he placed
away from direct sunlight, rain, or snow.
CHANGING CHANNELS
Once a channel is assigned to a unit. You can only change it by removing the batteries
and repeating the above procedure.
LOW-BATTERY WARNING
A low-battery indicator [ ] will activate on the sensor to indicate that the batteries are
low and require changing. Low batteries for a given sensor will also be indicated on
the main unit. Replace the batteries when the low-battery indicator appears.
THE COMFORT-LEVEL INDICATOR
The comfort level is based on the recorded relative humidity. An indicator will be
displayed ti show if the level is comfortable, wet or dry. (FIG D)
OPERATION
Once batteries are in place, the sensor will start transmitting samplings at 40-second
intervals.
The remote sensor reading shown on the LCD of the main unit depends on which
remote sensor channel has been chosen.
HOW TO RESET THE UNIT
The reset function is required only when the unit is operating in an unfavorable say or
malfunctioning.
To access:
1.
Lift open the battery compartment door.
2.
Insert a blunt stylus or the end of a paper clip into the hole marked RESET and
press.
3.
Replace the battery compartment door.
HOW TO USE THE TABLE STAND OR WALL MOUNT
This sensor comes with a wall-mount holder and a removable stand. Use either to hold
the unit in place.
Traceable® is a registered trademark of Control Company ©2008 Control Company. 92-4381-00 Rev. 2 052308
PRECAUTIONS
●
●
Do not immerse the unit in water.
●
Do not subject the unit to excessive force, shock, dust, temperature, or humidity,
which may result in malfunction, shorter electronic life span, damaged battery
and distorted parts.
●
Do not tamper with the units internal components. Doing so will invalidate the
warranty on the unit and may cause unnecessary damage. The unit contains no
user-serviceable pans.
●
Only use fresh batteries as specified in the user’s manual. Do not mix new and
old batteries as the old ones may leak.
Do not clean the unit with abrasive or corrosive materials. They may scratch the
plastic parts and corrode the electronic circuit.
NOTE ON COMPLIANCE
This product complies to standards and specifications of FCC and article number 334
of P11.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the users authority to operate the equipment.
NOTE: This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
●
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can he determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
●
●
●
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that which the
receiver is needed.
CAUTION
●
●
The content of this manual is subject to change without further notice.
●
The manufacturer and its suppliers held no responsibility to you or any other
person for any damage expenses, lost profits, or any other claim arise by using
this product.
Due to printing limitation, the displays shown in this manual may differ from the
actual display.
WARRANTY, SERVICE, OR RECALIBRATION
For warranty, service, or recalibration, contact:
CONTROL COMPANY
TIPTEMP.com
1-800-847-8367
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail sales@control3.com
www.control3.com
Control Company is ISO 9001 QualityCertified by DNV and ISO 17025 accredited
as a Calibration Laboratory by A2LA.
Traceable® is a registered trademark of Control Company ©2008 Control Company. 92-4381-00 Rev. 2 052308
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising