View - Volvo
Volvo Trucks. Driving Progress
FH 84 Pusher Tractor Tridem FH 84 PT3HA
3505
,394
Cab 2495
Chassis Dimensions [mm]
WB Wheelbase
3600
3900
A
D
Overall Chassis Length
Center of rear axle to back of cab
7140
2610
7440
2910
T
Theoretical Wheelbase
3728
4028
5125
4750
9875
5125
4785
9910
Chassis Weights [kg]
Front Axle
Rear Bogie
Kerb Weight
Turning Diameter [mm]
Turning Circle Diameter Kerb to Kerb
Turning Circle Diameter Wall to Wall
15100 16100
16500 17400
Plated Weights [kg]
Design
Gross Vehicle Weight
Gross Combination Weight
Front Axle
Rear Bogie
35000
44000
8000
27000
Important Notes
Chassis Dimensions
Cab Height: +305 mm for CAB-HSLP, -283 mm for CAB-LSLP, +450 mm for
CAB-XHSL.
D-measure includes a front clearance of 50 mm and for rigid trucks also a
subframe of 100 mm.
Height can vary ± 20 mm for leaf and ± 10 mm for air suspension.
All dimensions are for unladen chassis and any tag axles down.
Weight and dimensions are based upon the following tyres:
Front Axle Tyres:
315/80R22.5
Drive Axle Tyres:
315/80R22.5
Trailing/Pusher Axle Tyres:
315/80R22.5
Chassis weight includes oil, water, AdBlue, 70 litres fuel and without
driver. Kerb weight can vary ± 3%.
Turning diameters are theoretically calculated. Tag axle used: PA-HYDRS.
Legal weights can differ from country to country.
For more detailed weight information, including optional equipment weights,
ask your Volvo sales contact to enter your specification into the Volvo Weight
Information system (WIS).
Do NOT use this drawing for bodybuilding. Refer to Volvo Bodybuilder
Instructions and chassis assembly drawing FH84PT3HA.
1 (8)
Ref: FH 84 PT3HA 01 8NE 2017-09-04 ENGVT
FH 84 Pusher Tractor Tridem FH 84 PT3HA
Transport operation
□ RC-ROUGH
■ RC-SMOOT
Rough road conditions.
• Less than 95% of the driven distance on well maintained or
less maintained surfaced roads.
and / or
• In total not more than 5% of the driven distance on:
- Very badly maintained surfaced roads.
- Hard packed sand or gravel surface of very bad quality.
- Washboards.
- Soft unpaved surface.
- Off-road.
Smooth road conditions.
At least 95% of the driven distance on well maintained or less
maintained surfaced roads.
Driving occurs on:
- Badly maintained surfaced roads.
- Hard packed sand or gravel surface of good or bad quality.
Core components
■ PU-EHYS
El. hydraulically steered pusher axle with single wheels (two
wheels on complete axle)
□
□
■
□
FH Globetrotter sleeper cab
FH Low sleeper cab
FH Sleeper cab
FH Globetrotter XL sleeper cab
FH-HSLP
FH-LSLP
FH-SLP
FH-XHSL
■ EU6SCR
Euro 6 emission level with Selective Catalytic Reduction
(SCR), particulate filter and Exhaust Gas Recirculation (EGR)
■ D13K420
Diesel engine, 12.8 litre Euro 6 SCR +
Filter), 420 hp, 2100 Nm
Diesel engine, 12.8 litre Euro 6 SCR +
Filter), 460 hp, 2300 Nm
Diesel engine, 12.8 litre Euro 6 SCR +
Filter), 500 hp, 2500 Nm
Diesel engine, 12.8 litre Euro 6 SCR +
Filter), 540 hp, 2600 Nm
□ D13K460
□ D13K500
□ D13K540
□ EBR-EPG
□ EBR-EPGC
□ EBR-VEB
□ EBR-VEB+
■ AT2612F
□ ATO2612F
□ RTH2610F
■ RTS2370A
EGR (Diesel Particulate
EGR (Diesel Particulate
EGR (Diesel Particulate
EGR (Diesel Particulate
Engine brake with exhaust pressure governor, EPG
Volvo engine compression brake with exhaust pressure
governor, EPG (for I-shift)
Volvo Engine Brake, VEB (compression brake with exhaust
pressure governor, EPG)
Volvo Engine Brake, VEB+ (high efficiency compression brake
with exhaust pressure governor, EPG)
I-Shift automated mechanical 12-speed gearbox without clutch
pedal, max. engine torque 2600 Nm, max. permitted GCW
100000 kg.
I-Shift automated mechanical 12-speed overdrive gearbox
without clutch, max. engine torque 2600 Nm, max. permitted
GCW 100000 kg.
Suitable for hub reduction rear axles.
□ MEDIADF
□ MEDIANDF
□ VISI15
□ VISI15+
□ VISIC15
Visibility package
Visibility plus package
Visibility package FH Construction
□ ENOPT
□ ENOPT+
Energy optimization package
Energy optimization+ package
Chassis
□ FST-AIR
■ FST-PAR
□ FST-PAR3
Front air suspension
2 leaf front parabolic suspension (normal stiffness)
3 leaf front parabolic suspension (stiffer than normal)
□
■
□
□
Front axle load 10.0 tonnes
Front axle load 8.0 tonnes
Front axle load 8.5 tonnes
Front axle load 9.0 tonnes
FAL10.0
FAL8.0
FAL8.5
FAL9.0
■ FALIM
Front axle load limiter
■ FSTAB
□ FSTAB2
□ FSTAB3
Front stabilizer with normal stiffness
Front stabilizer with medium high stiffness
Front stiff stabilizer
■ RAL27
□ RAL32
□ RAL35
Rear axles load 27 tonnes
Rear axles load 32 tonnes
Rear axles load 35 tonnes
■ RSTAB3
Rear stiff stabilizer
□
□
□
■
First rear drive axle load limiter, 10.5 tonnes (speed controlled)
First rear drive axle load limiter, 11.5 tonnes (speed controlled)
First rear dive axle load limiter, 13 tonnes
First rear drive axle load limiter, 9.5 tonnes
RALIM105
RALIM115
RALIM13
RALIM95
□ ACTST-TO
Volvo Dynamic Steering (VDS) with extra pump and torque
overlay
□ PSS-DUAL
■ PSS-SING
Dual power steering system
Single power steering system
■ PSP-VAR
Power steering pump with variable displacement
■ EBS-MED
EBS (Electronic Brake System) medium package:
- ABS (Anti-lock Braking System)
- Lining Wear Sensing (20 % left)
- Lining Wear Control (incl. wear on the axle)
- Brake Blending
- Drag Torque Control
- Diff Lock Synchronization
- Diff lock Control
- Brake Temperature Warning
- External Brake Demand
- Diagnosis Via Truck Electronic System
- Traction Control System
- Emergency Brake Assistance
- Constant Wheel Brake Monitoring
- Coupling Force Control
- Automatic Parking Brake Activation
- Lining Wear Analyses (calc of remaining mileage)
- Hill Starting Assistance
- EBS status monitoring via Truck Electronic System
EBS (Electronic Brake System) standard package:
- ABS (Anti-lock Braking System)
- Lining Wear Sensing (20 % left)
- Lining Wear Control (incl. wear on the axle)
- Brake Blending
- Drag Torque Control
- Diff Lock Synchronization
- Diff lock Control
- Brake Temperature Warning
- External Brake Demand
Rear hub reduction tandem axles - bogie load 26 tonnes, GCW
100 tonnes
Rear single reduction tandem axles - bogie load 23 tonnes,
GCW 70 tonnes
Packages
□ VOR2017
Volvo Ocean Race 2017-2018
□ LHFP-V
Long haul fuel package - vehicle
□ DRIVE
□ DRIVE+
□ DRIVE++
Driving package FH
Driving plus package FH
Driving plus/plus package FH
□
□
□
□
FH sleeping/resting package with 1 bed
FH sleeping/resting package plus with 1 bed
FH sleeping/resting package with 2 beds
FH sleeping/resting package plus with 2 beds
1BED
1BED+
2BED
2BED+
■ AUDBAS
□ AUDHIG
□ EBS-STD
Audio basic. RDS radio with CD player, FM/AM antenna and
speakers in dashboard & doors.
Prepared for Dynafleet office internet portal support.
High power audio system. RDS radio with CD player (also
playing mp3/wma/wav files from CD), FM/AM antenna,
■ Standard Equipment
speakers in dashboard & doors & sleeping compartment,
integrated bluetooth phone and USB/Line inputs.
Prepared for Dynafleet office internet portal support.
Media package with infotainment. Prepared for both Dynafleet
vehicle onboard support and for Dynafleet office internet portal
support.
Media package with infotainment and Navigation support and
prepared for Dynafleet vehicle onboard support and for
Dynafleet office internet portal support.
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
2 (8)
Ref: FH 84 PT3HA 01 8NE 2017-09-04 ENGVT
FH 84 Pusher Tractor Tridem FH 84 PT3HA
- Diagnosis Via Truck Electronic System
- Traction Control System
- Emergency Brake Assistance
- Constant Wheel Brake Monitoring
- Coupling Force Control
- Automatic Parking Brake Activation
□ WHCP-T
(or behind) rear wheels
Transport mounted wheel chock(s) in cab outer luggage
compartment
□ CHAIN-S
Snow chains
□ HOOK-SC
Snow chain hooks.
Rear mounted for tractors and side mounted in rear overhang
for rigids. Two hooks on each side.
■ TOWF-NO1
□ TOWF-NO2
One front towing device
Two front towing devices
□ AUXPARK
□ AUXPARK4
Two extra parking brake chambers
Four extra parking brake chambers
■ FRAME300
Frame rail section external height 300 mm
■ FST8080
Frame section thickness - web 8.0 mm / flange 8.0 mm
□ TOWR-ONE
One rear towing device in frame end cross member
□ FIL-EEEB
□ FIL-TXEB
Frame inner liner from end of engine end to end of bogie
Frame inner liner from transmission cross member to end of
bogie
□ TREL15
■ TREL7-7
15 pol electrical trailer connector (ADR certified)
2x7 pol (24N+24S) electrical trailer connectors (UADR)
■ BBOX-L
Battery box on left hand side
□ TBC-DUO
■ TBC-EC
Trailer brake connection, Duomatic
Trailer brake connection, European Community
□ BATS-D
■ TRBR-STA
Stationary trailer brake control
■ BATS-S
Dual energy battery storage system (2 living batteries and 2
starter batteries)
Single energy battery storage system (2 batteries)
□ TRB-STRE
□ 2BAT210B
■ 2BATT170
□ 2BATT225
Gel batteries 2x210 Ah
Batteries 2x170 Ah
Batteries 2x225 Ah
Automatic low speed trailer brake activation (stretch brake) to
avoid jack-knifing and to improve steerability
■ RFEND-B
Rear 3 piece fenders with anti-spray function (all rear axles)
■ BATTAMP
□ BATTIND
Battery voltage and ampere gauge
Battery voltage, ampere and battery status gauge with visual
alerts
■ RFH-BAS
□ ADR2
ADR adaptation - transportation of dangerous goods, 2
switches (1 inside cab in dashboard, 1 outside on cab back
passenger side).
Optimal fender installation (rear and 2nd front axle) with regard
to legal demands, wheel/tyre sizes, chassis height and fifth
wheel height.
Highest fender installation (rear and 2nd front axle).
Suitable for rough and very rough road conditions.
Lower fender installation (rear and 2nd front axle).
Suitable only for smooth road conditions.
Increased risk of fender top wear.
□ MSWI-A
■ MSWI-C
ADR main switch - ADR switch circuit shut down
Chassis main switch - battery box placed toggle switch citcuit
shut down
Remote controlled main switch - key fob operated circuit shut
down
□ MSWI-R
□ ADTP-BC
■ ADTP-R
AdBlue tank behind/under cab on right hand side
AdBlue tank on right hand side
□
□
□
□
□
□
AdBlue tank usable volume 48 litres
AdBlue tank usable volume 64 litres
AdBlue tank usable volume 65 litres
AdBlue tank usable volume 68 litres
AdBlue tank usable volume 90 litres
AdBlue tank usable volume 100 litres
ADB048
ADB064
ADB065
ADB068
ADB090
ADB100
□ RFH-HIG
□ RFH-LOW
□ ATANK-AL
■ ATANK-ST
Aluminium air tanks
Steel air tanks
■ TL-LED
LED tail lamps (tail light, exterior marker light, brake light,
hazard warning light, reverse light, rear fog light and reflector).
■ BLIGHT-E
Emergency brake light
Rims and Tyres
□ RT-AL
□ ADTC-BF
AdBlue tank cover painted in silver metallic
□ RT-ALDU
□
■
□
□
□
Horizontal muffler, left exhaust outlet
Horizontal muffler, rear exhaust outlet
Horizontal muffler, right exhaust outlet
Horizontal muffler, vertical exhaust outlet on right hand side
Vertical muffler, vertical exhaust outlet on right hand side
■ RT-STEEL
Brushed aluminium rims with std holes (long stud fixing) on all
axles
Dura-Bright polished aluminium rims with std holes (long stud
fixing) on all axles
Dura-Bright polished aluminium rims with countersunk holes
(short stud fixing) on all axles
Brushed aluminium rims with countersunk holes (short stud
fixing) on all axles
Steel rims on all axles
□ WCAP
Wheel caps
□ JACK-12T
□ JACK-15T
■ JACK-20T
Jack 12 tonnes
Jack 15 tonnes
Jack 20 tonnes
■ TOOL-BAS
□ TOOLKIT
Basic tools (combination screw driver, socket wrench)
Extended tool kit
□ INFLAHOS
Tyre inflation hose (18 metres) with nozzles in both ends
□ GAUGE-TP
Tyre pressure gauge
□ OBDEP-C
EU6 mandatory on board diagnostics, phase C regulations
ESH-LEFT
ESH-REAR
ESH-RIGH
ESH-VERT
ESV-VERT
□ EXST-SSP
□ EXST-ST
Bright polished vertical stainless steel exhaust top pipe
Aluminized steel vertical exhaust top pipe
□ WHC-FIX2
■ WHC-FOL2
Two fixed wheel chocks
2 foldable wheel chocks
■ WHCP-F
Wheel chock(s) in the front part of the vehicle.
- TRACTOR, BBOX-L, Fold, 1/2 w chocks
= Top of
left side battery box
- TRACTOR, BBOX-EF, Fold, 1/2 w chocks
= Top of
lefts side fuel tank
- TRACTOR, BBOX-EF, Fix, 2 w chocks
= Left
frame front of fuel tank
- RIGID, 1 front axle, Fold, 1/2 w chocks
= Top of left
side battery box
- RIGID, 2 front axles, Fold, Frame free space, 2 wc = Top of
left side battery box
- RIGID, 2 front axles, Fix, W/o frame free space,2 wc = Left
frame behind 1st front wheel
Wheel chock(s) in the middle part of the vehicle
- TRACTOR, BBOX-L, Fix, 1/2 w chocks
= Left frame front
of rear wheels
- RIGID, 1 front axle, Fix, 1/2 w chocks = Left frame front of
□ WHCP-M
■ Standard Equipment
□ RT-ALDP
□ RT-ALDPD
Powertrain equipment
□ ASO-C
□ ASO-ULC
One crawler gear
Two crawler gears, one ultra low crawler and one crawler
□ TRAP-HD
Reinforced gearbox application.
For manual gearboxes a heavy-duty nodular iron range
housing.
For I-shift gearboxes (2412 excl.) a reinforced gear shifting
system.
□ PVT-EXT
Extended topography information, learning by GPS positioning
and centrally stored data
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
3 (8)
Ref: FH 84 PT3HA 01 8NE 2017-09-04 ENGVT
FH 84 Pusher Tractor Tridem FH 84 PT3HA
□
□
□
□
□
TP-BAS
TP-CON
TP-DIST
TP-HD
TP-HD3
□ TP-LONG
I-shift City gear changing software
I-shift construction gear changing software
I-shift distribution gear changing software
I-shift Heavy Duty gear changing software
I-shift Heavy Duty & Fuel Economy+ gear changing software
prepared for using GPS positioning (centrally stored road
memory, I-See)
I-shift long haul gear changing software
□ HPE-T53
□ HPE-T70
□ HPE-V45
□ HPE-V75
□ AMSO-AUT
I-shift manual gear shift available in automatic mode incl
kickdown function
□ PTR-D
□ AVO-ENH
Enhanced I-shift software for construction and off road
applications
□ PTR-DH
□ APF-ENH
Enhanced I-shift PTO functions (Auto Neutral / Reverse Inhibit
/ Split Box Connection)
□ CD40B-O
■ CS43B-O
Double plate clutch, plate diameter 400 mm
Single plate clutch, plate diameter 430 mm
□ RET-TH
Retarder (incl cooler) for manual and I-shift gearboxes with oil
as brake fluid
□ TC-MAOH2
Extra high performance cooler for manual/I-shift gearboxes air/oil
Basic performance cooler for manual/I-Shift gearboxes water/oil
High performance cooler for manual/I-Shift gearboxes water/oil
High performance cooler for manual gearboxes with retarder air/water/oil
High performance cooler for manual gearboxes with retarder –
air/oil (cooler integrated in retarder)
□ TC-MWO
□ TC-MWOH2
□ TC-RAO
□ TC-RWO
□ PTR-DM
□ PTR-F
□ PTR-FH
□ PTR-FL
□ PTRD-D
□ PTRD-D1
displacement, single flow
Rear engine mounted hydraulic pump F2-53/53, fixed
displacement, twin flow
Rear engine mounted hydraulic pump F2-70/35, fixed
displacement, twin flow
Rear engine mounted hydraulic pump VP1-45, variable
displacement, single flow
Rear engine mounted hydraulic pump VP1-75, variable
displacement, single flow
Mechanical gearbox driven low speed power take-off, 1 rear
connection (DIN 5462 / ISO 7653) for plug-in pump (max. 1000
Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
connection (DIN 5462 / ISO 7653) for plug-in pump (max. 600
Nm).
Mechanical gearbox driven medium speed power take-off, 1
rear connection (DIN 5462 / ISO 7653) for plug-in pump (max.
600 Nm).
Mechanical gearbox driven low speed power take-off, 1 rear
flange connection (SAE 1410 / ISO 7647) for propeller shaft
(max. 1000 Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
flange connection (SAE 1310 / ISO 7647) for propeller shaft
(max. 600 Nm).
Mechanical gearbox driven low speed power take-off, 1 rear
flange connection (SAE 1310 / ISO 7647) for propeller shaft
(max. 600 Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
and 1 front connections (DIN 5462 / ISO 7653) for plug-in
pumps (max. 870 Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
flange connection (SAE 1410 / ISO 7647) for propeller shaft / 1
front connection (DIN 5462 / ISO 7653) for plug-in pump (max.
870 Nm).
Mechanical gearbox driven power take-off, 2 rear flange (highlow speed) connections (SAE 1310/1410 / ISO 7647) for
propeller shafts / 1 front (high speed) connection (DIN 5462 /
ISO 7653) for plug-in pump (max. 870/1000 Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
flange connection (SAE 1410 / ISO 7647) for propeller shaft
(max. 870 Nm).
□ 2COM1100
■ 2COMP900
Dual cylinder air compressor 760 cc / 1100 l/min
Dual cylinder air compressor 636 cc
□ CLU-AIRC
Air compressor clutch automatically declutched when not
needed in order to save fuel
□ AIRIN-FR
■ AIRIN-HI
□ AIRIN-LO
Front air intake
High air intake
Low air intake
□ ACL1ST-S
Air cleaner with additional filter element (primary + secondary)
■ 24AL110B
□ 24AL120B
□ 24AL150B
Alternator 110 Ampere
Alternator 120 Ampere
Alternator 150 Ampere
□ CCV-C
■ CCV-OX
Closed crankcase ventilation
Closed crankcase ventilation with oil separator and a
maintenance free gas centrifuge
□ HPG-F51
□ PRIM-EL
□ HPG-F81
■ PRIM-MAN
Electrical priming pump for fast and easy bleeding of the fuel
system
Manual priming pump for fast and easy bleeding of the fuel
system
■ AF-R
Hot fuel recirculation heated fuel filter
Cab Interior, Driving
■ EST-AID
Engine start pre-heating element
□ DRC-AMII
□ 220EBH15
Engine block heater, 220 volt, 1.5 kW
■ DRC-AUTO
□ PTER-100
Rear engine mounted clutch independent power-take-off with
flange connection (DIN 100 / ISO 7646)
Rear engine mounted clutch independent PTO with splined
shaft groove (female) for a close coupled pump (DIN 5462 /
ISO 7653)
Rear engine mounted clutch independent power-take-off with
flange connection (SAE 1410 / ISO 7647)
Regeneration control of diesel filter particulates - auto initiation
/ manual on demand / manual inhibition
Regeneration control of diesel filter particulates - fully
automatic (in motion)
■ STWPOS-L
Left hand drive
■ STWM-LE
Leather steering wheel
□ STGW-AD2
■ STGW-ADJ
Mechanically adjustable steering wheel with neck tilt
Mechanically adjustable steering wheel
□ AIRBAG
Airbag on driver side
■ 1DAYDIG
□ 1DAYDIG2
One day digital tachograph, EC approved
Gen 2 one day digital tachograph, EC approved
□ ARSL
Additional road speed limiter (switch in dashboard)
□ DTRI-PER
FH: Dashboard, steering wheel cover and door panels in
greyish brown (peregrine).
FH16: Dashboard in greyish brown, steering wheel cover and
door panels in black (raven).
□ PTER-DIN
□ PTER1400
□ HPE-F101
□ HPE-F41
□ HPE-F51
□ HPE-F61
□ HPE-F81
□ PTRD-F
Rear engine mounted hydraulic pump F1-101, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-41, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-51, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-61, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-81, fixed
■ Standard Equipment
□ PTRD-D2
□ HPG-F101
□ HPG-F41
□ HPG-F61
□ EIDLESD
Gearbox mounted hydraulic pump F1-101, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-41, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-51, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-61, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-81, fixed displacement,
single flow
Engine idle shut down
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
4 (8)
Ref: FH 84 PT3HA 01 8NE 2017-09-04 ENGVT
FH 84 Pusher Tractor Tridem FH 84 PT3HA
□ DTRI-SRA
Dashboard and steering wheel cover in light beige (skylark),
door panels in light beige for FH and black (raven) for FH16.
□ CRUIS-E
■ CRUISEC
Cruise control I-Cruise with controls in the steering wheel,I-Roll
incl. Adding PVT-EXT gives I-See.
Basic cruise control with controls in steering wheel
□ WARNLAMP Portable warning lamp with batteries
□ HWSS-AC
Adaptive cruise control with forward collision warning
□ LAMP-IN
Inspection lamp with 10 m cable
□ LSS-DW
Lane keeping support - lane departure warning system
□ BULBKIT
Bulb and fuse kit
□ LCS
Lane Change Support
■ WRITEPAD
Writing pad with spring-loaded paper clip
□ DAS-W
Driver Alert Support (drowsy driver warning)
Cab Interior, Living
□ RSENS-W
Wiper rain sensor
■ UPHTRI02
□ CU-ECC
□ CU-ECC2
Fully electrically controlled air conditioning with sun sensor
Fully electrically controlled air conditioning with sun sensor,
mist sensor, air quality sensor and carbon filter
□ UPHTRI03
■ IMMOBIL
Immobiliser
□ ALARM-B
□ ALARM-E
Burglar alarm - cab
Burglar alarm - cab/body/trailer
□ ALCOLOCK
Alcolock
□ AMPL400
Amplifier, 8 channel, 400 W, subwoofer
□ PHONE-PK
Telephone preparation kit (antenna, antenna attachment, cable
from antenna to radio shelf).
■ WLIFT-AD
Electrical window lift, auto up/down driver side; el operated on
passenger side
□ ISUNS-BS
Manually manoeuvred side interior sun visor (roller blind type)
on both sides
Manually manoeuvred side interior sun visor (roller blind type)
on driver side
□ DST-LUX1
Electrical textile interior sun visor (roller blind) integrated in
front shelf
Manual interior textile sun visor (roller-blind) integrated in front
shelf
□ SBD-RED
Red safety belts, passenge and driver seats
□ SBPRE-DS
Driver seat belt pretensioner
□
□
□
□
PST-BAS1
PST-BSL1
PST-CF4
PST-CF5
□
□
■
□
PST-RX1
PST-RX2
PST-STD2
PST-STD4
Passenger seat, basic, non suspended
Passenger seat, basic, sliding, non suspended
Passenger seat, comfort, suspended, belt in seat
Passenger seat, comfort, suspended, belt in seat, electrically
heated
Passenger relax seat, swivel/tilt
Passenger relax seat, swivel/tilt/heat
Passenger seat, regular, non suspended
Passenger seat, regular, suspended
■ ISUNS-DS
□ ISUNF-RE
■ ISUNF-RM
□ UPHTRI05
□ UPHTRI06
□ UPHTRI07
■ CSPL-BX
□ CSPL-BXD
Open storage in lower center dash panel
Storage drawer in lower center dash panel
□ CSPU-SDR
One open storage and one drawer (behind push open lid) in
upper part of dash panel center section
Two open storages (behind push open lid) in upper part of
dash panel center section
■ CSPU-SS
□ AIDKIT1B
□ ADFS
Two extra DIN slots in front shelf (push/pull storage),
165x40x180 mm (WxHxD)
□ BUPALARM
Back-up alarm
□ BUPMON
Back-up monitor including a 7 inch colour display integrated in
dashboard, Waeco CCD-camera (delivered loose in cab) with
a heated lens, motorised lens protection, 1 m pigtail cable
(front) and 10 metres chassis cable for tractor /20 metres for
rigid. Camera wirings not installed. Use PCA30081 for
installation.
■ DST-CF1
□ DST-CF4
□ DST-CF5
□ DST-CF6
□ DST-LUX2
First aid kit containing sticking plaster, compresses, elastic
bandages, gloves, scissors, triangular bandage, bandaging
cloths, adhesive tape and rescue sheet (German
requirements)
Seat upholstery with black striped textile insert, black smooth
textile bolster & red vinyl side insert & textile interior trim in
matching grey nuances
Seat upholstery with grey/beige soft striped textile insert,
grey/beige smooth textile bolster & soft textile interior trim in
matching grey and beige colours
Seat upholstery with dark grey leather insert and black leather
bolster & vinyl interior trim in matching grey nuances
Seat with dark grey leather insert and black leather bolster &
textile interior trim in matching grey nuances
Seat with dark grey leather insert and black leather bolster &
soft textile interior trim in matching grey and beige colours
Driver seat, comfort, suspended
Driver seat, comfort, suspended, belt in seat
Driver seat, comfort, suspended, belt in seat, electrically
heated
Driver seat, comfort, suspended, belt in seat, electrically
heated, ventilated
Driver seat, de luxe, suspended, belt in seat, electrically
heated, ventilated
Driver seat, de luxe, suspended, belt in seat, electrically
heated
□ SBPRE-PS
Passenger seat belt pretensioner
□ ARMRE-BB
□ ARMRE-DB
□ ARMRE-PB
Two armrests on both driver and passenger seats
Two armrests on driver seat
Two armrests on passenger seat
□ ARU-BAS
□ ARU-LEA
Vinyl armrest upholstery
Leather armrest upholstery
□ GRABHI-L
Leather covered steel instep grab handle
□ RTOLL-PK
Preparation kit for road toll collect (GPS/GSM antenna and
cables)
■ FMAT-RUB
□ FMAT-TX2
□ LOADIND
Load indicator with dashboard display.
Measures axle pressures, load weight and total weight of truck
and one trailer.
Two black rubber floor mats
Two textile (dark grey on FH/FM, black on FH16) and two
black rubber floor mats
■ LBK80F
Lower fixed bunk, foldable 55 degrees - 2000x815/740/660
mm (middle/head/feet).
Safety net included.
Lower electrically manoeuvred recline bunk, foldable 55
degrees - 2000x815/740/660mm (mid/head/feet). Safety net
included.
Lower manually manoeuvred recline bunk, foldable 55 degrees
- 2000x815/740/660 mm (mid/head/feet). Safety net included.
□ REMC-MF
Wireless remote control - multi functional
□ FIREXT2G
□ FIREXT3S
Fire extinguisher 2 kg, German decal
Fire extinguisher 3 kg, Swedish/English decal
□ WARNVEST
Warning vest. Fulfils European standard according to EN 471
class 2.
■ WARNTRI2
Two warning triangles
■ AIDKIT
First aid kit containing sticking plaster, washing and drying
pads, compresses, elastic bandages, respiratory mask, gloves
and scissors
■ Standard Equipment
□ LBK80FRE
□ LBK80FRM
□ MATL-FI
■ MATL-SF
Mattress lower bunk - firm for over approx. 100 kg, pocket
springs.
Mattress lower bunk - semi-firm up to approx 100 kg, pocket
springs.
□ OLMAT-BA
Overlay mattress protector, 28 mm thick black textile
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
5 (8)
Ref: FH 84 PT3HA 01 8NE 2017-09-04 ENGVT
FH 84 Pusher Tractor Tridem FH 84 PT3HA
□ OLMAT-PR
Overlay mattress protector, 35 mm thick black textile
□ TBK60AD
Height adjustable top bunk 600x1900 mm, foldable up to 52
degrees to rear wall (depending on cab version and upper
storage). Safety net included.
Fixed top bunk 600x1900 mm, foldable up to 52 degrees to
rear wall (depending on cab version and upper storage). Safety
net included.
Height adjustable top bunk 700x1900 mm, foldable up to 52
degrees to rear wall (depending on cab version and upper
storage). Safety net included.
Fixed top bunk 700x1900 mm, foldable up to 52 degrees to
rear wall (depending on cab version and upper storage). Safety
net included.
□ TBK60F
□ TBK70AD
□ TBK70F
□ EXTL-ENH
Enhanced cab exterior finish (cab painted insteps & bumper
(bumper spoiler if fitted), mirror housings (FH16 silver painted),
sun visor if fitted (FH16 silver painted) and door handle (FH16
chrome)).
Construction bumper excluded.
■ GLAS-TIN
□ GLAS-UNT
Tinted windows (front/side/rear)
Untinted windows
■ DGLAS-H
□ DGLAS-L
Tempered door glass
Laminated door glass
■ LOCK-REM
Central door locking with remote control
■ BUMP-B
□ BUMP-B2
□ BUMP-HD
Plastic front bumper
Steel front bumper
Heavy duty front bumper
■ BUMP-SP
Front bumper spoiler
□ GUARD-EH
Guard plate for cooling pipes and oil sump
■ BUGNET
Radiator screen / Mosquito net (PVC coated fibreglass) in front
of radiator
□ PH-CAB2
□ PH-ENGCA
Cab parking heater, 2 kW
Engine and cab parking heater
■ SLCP-BAS
□ SLCP-LUX
Basic sleeper control panel (controlling interior light, parking
heater, roof hatch and door lock)
Luxuary sleeper control panel in cab back (controlling interior
light, parking heater/cooler, roof hatch, door lock, alarm clock,
window and audio)
□ SAFE
Key operated safe box under bed (FH) or at bed end (FM)
□ CTILTP-E
■ CTILTP-M
Electrical cab tilt pump
Manual cab tilt pump
□ RUS-BAS
□ RUS-HIG
Rear cab upper storage 154 litres (300 mm high)
Rear cab upper storage 245 litres (440 mm high)
□ FCABS-A
■ FCABS-M
Air front cab suspension
Mechanical cab suspension
□ TABLE
Foldable and height adjustable table to be mounted to the
lower bunk
□ RCABS-A
■ RCABS-M
Air rear cab suspension
Mechanical rear cab suspension
□ REFR-RUS
□ REFRIG
28 litre rear upper wall mounted refrigerator with deviders
33 litre under bunk mounted refrigerator with freezer and
deviders
■ HCC-INEX
Lockable front lid - Exterior and interior hood catch control
□ MIRCOMF
Electrically heated & operated main rear view mirrors and
wide angle mirrors (both sides).
Close view mirror on passenger side.
Electrically heated main rear view mirrors and wide angle
mirrors (both sides), both electrically operated on passenger
side. Close view mirror on passenger side.
□ MICRO-PK
Preparation kit for microwave oven (el. cables to front shelf)
□ BOTH-D
One 1.5 litre plastic soft-drink bottle holder under dashboard
centre section
Two 1.5 litre plastic soft-drink bottle holders, one under
dashboard centre section and one mounted to the under bunk
drawer.
One 1.5 litre plastic soft-drink bottle holder mounted to the
under bunk drawer
■ MIRSTD
□ COFMA-PK
Preparation kit (24V) for coffee maker
■ INLI-BAS
Interior white light with smooth light transition at on/off, no
dimming
Interior white and red (night) light with smooth light transition at
on/off
Interior white and red (night) light with smooth light transition at
on/off and dimmer
□ BOTH-DL
□ BOTH-L
□ INLI-NL
□ INLI-NLD
□ ARL-FLEX
Two (driver and passenger side) reading lamps with flexible
arms (snake lamps) and led lamps fitted on side walls
■ RH-EE
□ RH-ETR
□ RH-MTR
Without roof hatch, sky window / emergency exit (tinted glass)
Roof hatch - Electrically operated / Tinted glass / Rear opening
Roof hatch - Manually operated / Tinted glass / Rear opening
□ SWIND-BS
Extra side window on both sides
■ VANMIR
Vanity mirror in front shelf lid.
In sleeper cab on passenger side and in high/extra high cabs
in middle section of the front shelf.
□ AS-FUS
□ INFOT-PK
One extra shelf in each of the two front upper storage
compartments.
Only 1 shelf if microwave oven mounted in one of the two
compartments.
Preparation kit (bracket, security straps, power cable, antenna
cable and aux cable) for mounting of a television above driver
door.
Cab Exterior
■ EXTL-BAS
Basic exterior finish in a lightning grey colour of cab
surrounding parts (mirror housings, insteps, bumper and if
fitted bumper spoiler and sun visor).
If fitted roof air deflector, side air deflector and chassis fairings
are always painted in cab colour.
■ Standard Equipment
■ AMIR-F20
Front close view mirror above windscreen, passenger side
(radius 200 mm)
□ SUNV-H
Exterior transparent dark grey front sun visor
□ AD-ROOF
Roof air deflector. Design (length, height etc.) automatically
calculated and varies depending on vehicle total height
(chassis height, cab type, tyres etc).
□ AD-SIDEL
□ AD-SIDES
Long cab side air deflector
Short cab side air deflectors
■ HL-BASIC
□ HL-BHID
□ HL-DBL
Halogen H7 head lamps
Bi-Xenon head lamps, high intensity discharged
Bi-Xenon dynamic head lamps, high intensity discharged.
The dipped beam follows the road, activated by a signal from
the steering system.
Activated when driving with Drive+ (D+) on the light control
switch.
Active at speeds between 10-25 km/h (set by driver).
Operates at +15 to -8 degrees.
□ HL-CLEAN
High pressure headlamp cleaner
□ HLP-ST
Steel headlamp protection
□ HL-ADJ
Adjustable headlamps to adjust the height of the light beam
■ DRL-LED
V-shaped ("V-light") day running light (LED).
Turned on low beam gives a dimmed "V-light".
□ DRIVL2
■ UDRIVL
Two auxiliary front driving lamps
Without auxiliary front driving lamps
■ FOGL-WC
White front fog lamps
□ CL-STAT
Cornering lights
□ ASL-RF2
Two Hella H11 70W spot lamps in sign box (one on each side
of the Globetrotter sign)
□ BEACOA2F
Two front roof mounted amber rotating beacon warning lamps.
Mounted on accessory bracket if ordered, otherwise on cab
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
6 (8)
Ref: FH 84 PT3HA 01 8NE 2017-09-04 ENGVT
FH 84 Pusher Tractor Tridem FH 84 PT3HA
□ BEACOA2R
□ BEACON-P
□ BEACONA4
roof on both sides of the hatch.
Two rear roof mounted (on accessory bracket) amber warning
lamps.
Rotating beacon lamps mounted on sleeper cab.
Flashing LED lamps mounted on high/extra high sleeper cabs.
Prepared wiring (switch and connected relay included) for
warning lamps on cab roof.
Max load 300 W.
Four roof mounted amber warning lamps.
2 front mounted (on accessory bracket if ordered) rotating
beacon lamps.
2 rear mounted (on mandatory accessory bracket) rotating
beacon lamps on sleeper cab.
2 rear mounted (on mandatory accessory bracket) flashing
LED lamps on high/xhigh sleeper cabs.
fifth wheel
□ 5WL-S1
Fifth wheel lubrication - locking mechanism and top plate
□ TCIND
Trailer connection indication with sensors for height, kingpin
and coupling lock
□ RAMP-LOW
□ RAMP-MED
Low height sliding members/protection members
Medium height sliding members/protection members
■ RDECK
Basic rear deck (one plate between frame rails and one over
left fuel tank or left battery box)
Medium rear deck (two plates between frame rails and one
over left fuel tank or left battery box)
□ RDECK-M
□ SRWL-PK
□ CABPT-R1
■ CABPT-R2
One front cab roof pass through on passenger side
Two front cab roof pass throughs, one on each side
□ SWL-2RA
□ SPOTP-F
□ SPOTP-R
□ SPOTP-RF
Spotlamp preparation in cab front, max 280W
Spotlamp preparation on cab roof, max 280W
Spotlamp preparation on cab roof and in cab front, max
2x280W
□ SWL-2RW
□ ROS-IL
□ WL-TA1A
□ ROS-ILP
Illuminated roof sign with switch in radio shelf. Switch for
turning on/off.
Wiring preparation kit (wires and switch) for cab sign or roof air
deflector illumination
□ CSGN-GTR
GLOBETROTTER decal in the cab roof sign area
■ HORN-F1S
One front mounted (behind grille) single tone air horn, Jericho.
Operated by steering wheel buttons.
Two roof mounted single tone chromed air horns. Operated by
steering wheel buttons.
□ HORN-R2S
□ ANT-CBR
Right hand side roof mounted foldable antenna and cables for
CB radio, single aerial.
□
□
□
□
□
□
□
Front, middle & rear roof mounted accessory brackets
Front roof mounted accessory bracket
Front & middle roof mounted accessory brackets
Front & rear roof mounted accessory brackets
Middle roof mounted accessory bracket
Rear roof mounted accessory bracket
Rear & middle roof mounted accessory brackets
ACCBR-AP
ACCBR-F
ACCBR-FM
ACCBR-FR
ACCBR-M
ACCBR-R
ACCBR-RM
□ STUC-B
□ STUC-L
□ STUC-R
Left and right storage compartments under cab
Left storage compartment under cab
Right storage compartment under cab
□ RFCAR-BC
Rear fender carrier back of cab
□ LADDER
Ladder back of cab
□ REFS-TW
□ REFS-TY
Reflecting white cab side stripes by-packed in cab
Reflecting yellow cab side stripes by-packed in cab
Superstructure preparations
■ 5WM-ISHD
□ 5WM-ISOH
□ 5WM-ISOM
Fifth wheel ISO mounting on 16 mm mounting plates for heavy
duty applications
Fifth wheel ISO mounting on high Z-profiles (t=8 mm) with 10
mm ISO saddle.
Z-profile height above frame = 80 mm.
Total height above frame 90 mm.
Fifth wheel ISO mounting on medium L-profiles (t=8 mm) with
10 mm ISO tie plate.
L-profile height above frame = 50 mm.
Total height above frame 60 mm.
□
□
■
□
5WH150
5WH185
5WH190
5WH290
Fifth
Fifth
Fifth
Fifth
□
□
□
■
□
□
5WT-JO11
5WT-JO8
5WT-JO9
5WT-JOHD
5WT-SH
5WT-SH2
Jost JSK 38G cast iron heavy duty fixed fifth wheel
Jost JSK 37 cast iron fixed fifth wheel
Jost JSK 42 cast iron fixed fifth wheel
Jost JSK 38C cast iron heavy duty fixed fifth wheel
SAF-Holland/+GF+ SK-S 36.20 V cast iron fixed fifth wheel
SAF-Holland/+GF+ SK-HD 38.36 cast iron heavy duty fixed
wheel leg-height 150 mm
wheel leg-height 185 mm
wheel leg-height 190 mm
wheel leg-height 290 mm
■ Standard Equipment
□ SWL-PK
■ WL-TA1W
□ WLC-H2A
□ WLC-H2W
□ WLC-PKH
□ WLC-PKL
□ WLC-PKLH
Wiring preparation for chassis mounted working lamps and a
3-position switch (On/Off/Reverse auto on).
Max load 280W.
Two H3 35W amber rear chassis mounted (LH/RH side)
working lamps and a 2-position switch (On/Off)
Two H3 70W white rear chassis mounted (LH/RH side)
working lamps and a 2-position switch (On/Off)
Wiring preparation for chassis mounted working lamps and a
2-position switch (On/Off). Max load 280W.
Trailer arch working lamp with amber coloured lens and
H3/35W bulb
Trailer arch working lamp with white lens and LED/70W bulb
Two H3/70W working lamps with amber coloured lens high
mounted back of cab (switch incl).
Two H3/70W working lamps, white lens high mounted back of
cab (switch incl).
Preparation kit (cables and switch) for high mounted working
lamps back of cab (pass through in cab rear roof included).
Max load 280W.
Preparation kit (cables and switch) for low mounted working
lamps back of cab (pass through in cab rear wall included).
Max load 280W.
Preparation kit (cables and switch) for low and high mounted
working lamps back of cab (pass throughs in rear wall and rear
roof included). Max load 280W.
■ ECBB-BAS
□ ECBB-HIG
Body builder electrical centre without any body builder module
Body builder electrical centre with cab body builder module
□ BBCHAS1
One 7-pole connector for Body builder interface.
Wiring harness routed from the bodybuilder electrical
distribution box inside the cab to a connection point inside the
right frame rail beside the gearbox.
Three 7-pole connectors for Body builder interface.
Wiring harness routed from the bodybuilder electrical
distribution box inside the cab to a connection point inside the
right frame rail beside the gearbox.
□ BBCHAS3
□ BEPR-T2
Body builder electrical software preparation for tipper with
remote control
□ TD-BAS
■ TD-LED
Trailer detection without LED sensor
Trailer detection with LED sensor
□ AUXL-SPK
Electrical preparation kit (wiring and a switch in dashboard) for
snow plough lights.
Preparation for installation of additional headlights and
additional turning indicators.
□ TAILPRE2
□ TAILPREP
Tail lift preparation kit, wireless remote operation
Tail lift preparation kit, wire remote operation
□ AESW2
Two Body builder bistable electrical switches (marked AUX1 /
AUX2)
Two Body builder bistable electrical switches (marked
AUX1/AUX2) and in an empty 4-group preparation another four
bistable switches with dummy switch caps
□ AESW2PK
□ AUXSW-4
Wiring for 4 extra hardwired switches (from Body builder
electrical centre to switch positions)
Services
■ TGW-3GWL
Telematics gateway with 3G modem and WLAN
□ FMS-PK
Fleet Management System gateway, preparation kit
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
7 (8)
Ref: FH 84 PT3HA 01 8NE 2017-09-04 ENGVT
FH 84 Pusher Tractor Tridem FH 84 PT3HA
□ DRUT
My truck app gives the driver instant status information and
control of the vehicle remotely from a smartphone or tablet.
The variant enables the My truck app to connect to the vehicle.
■ Standard Equipment
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
8 (8)
Ref: FH 84 PT3HA 01 8NE 2017-09-04 ENGVT
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement