IP / Ethernet Extenders Manual IPB-A1100Q Rear view Front view Rear view Front view IPB-A1200Q IPB-A1100Q* Active IP Balun over Cat5e/6 IPB-A1200Q* Active IP Balun over Coaxial *Each set includes one transmitter and one receiver. Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant. ENFORCER IP / Ethernet Extenders Introduction: ENFORCER Active IP Baluns are designed to extend the range of IP cameras or any TCP/IP device beyond the 300ft (100m) limit of Ethernet. The units do not filter out any protocols, codes, or applications, ensuring compatibility with any IP camera and its software. Specifications: Range Input connector Output connector Operating voltage Current draw (power supply) Link cable Cat5e/6 cable Ethernet speed IPB-A1100Q 3,900’ (1,200m) IPB-A1200Q 5,900’ (1,800m) RJ-45 RJ-45 BNC 5VDC (adapter included) 750mA Cat5 or better RG59/U or better Cat6 recommended RG6/U recommended TIA/EIA—568-B 10/100Mbps Parts List: 2 x Active IP Baluns 2 x 5VDC power adapters Dimensions 1 x Manual 8 x Mounting screws 8 x Plastic anchors Front Top Rear 41/2” 115mm 25/8” 67mm 511/16” 145mm 11/16” 27mm PB-A1100Q shown. Both models are the same size. Overview: IPB-A1100Q Rear 5VDC Connector Front (same for both models) IPB-A1200Q Rear RJ-45 Connector Tx/Rx DIP Switch 2 BNC Connector RJ-45 Connector Mounting tabs Status LEDs (4 per unit) (Power / RX / Link) SECO-LARM U.S.A., Inc. ENFORCER IP / Ethernet Extenders Installation: Rear panel connections IPB-A1100Q Rear panel connections IPB-A1200Q Set Tx/Rx DIP Switch Set Tx/Rx DIP Switch Connect Cat5e/6 cable between the receiver and transmitter Connect coax cable between the receiver and transmitter Front panel connections Both models Tx/Rx DIP Switch Positions Connect 5VDC Adapter Connect Cat5e/6 cable to a TCP/IP device. Each unit can act either as a transmitter (Tx) or a receiver (Rx). To set the function of a unit, simply set the DIP switch located on the rear of the unit to the desired position. The unit is a receiver The unit is a transmitter 1. Determine the location where the units will be placed as well as how much cable will be required. 2. If desired, use the included screws to mount the receiver and transmitter to a wall or other surface. Use the mounting tabs found on the corners of the enclosure. 3. On one unit, switch the Tx/Rx DIP switch to “Tx”. This is now the transmitter. 4. Connect the transmitter to an IP camera or other TCP/IP output device using Cat5e/6 cable. Connect via the Ethernet port found on the front of the Active IP Balun. 5. On the second unit, switch the Tx/Rx DIP switch to “Rx”. This is now the receiver. 6. Connect the receiver to a DVR, PC or other TCP/IP receiving device using Cat5e/6 cable. Connect via the Ethernet port found on the front of the Active IP Balun. 7. Run a cable between the two units and connect them via the rear-panel connectors. Use Cat5e/6 cable for the IPB-A1100Q. Use coaxial cable for the IPB-A1200Q. 8. Connect one 5VDC adapter to the transmitter and another to the receiver. 9. Switch on the IP source (i.e. CCTV camera) and verify that the system is functioning properly. Sample Application: IPB-A1100Q IP Camera IPB-A1200Q IP Camera SECO-LARM U.S.A., Inc. Up to 3,900’ (1,200m) of Cat5e/6 PC or DVR Up to 5,900’ (1,800m) of coaxial PC or DVR 3 ENFORCER IP / Ethernet Extenders Troubleshooting IP device does not function correctly Make sure the balun is powered on both sides. Make sure the IP source and DVR or PC are powered. Test the coaxial or Cat5e/6 cable between the receiver and transmitter and make sure it is functional. Make sure that there are no problems with the IP device, cables, or DVR by plugging the IP device directly into the DVR or PC using the Cat5e/6 cables. Make sure that the Tx/Rx DIP switches are in the correct position for each unit (see page 3 for details). Make sure that the cable does not exceed the maximum distance (see page 2 for more details). Products Available from SECO-LARM: VGA over Cat5e/6 Passive Video Baluns Active Balun Hub CCTV Power Supplies Voltage Converters and Boosters Rack Mount Power Supply WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else. NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM. SECO-LARM® U.S.A., Inc. 16842 Millikan Avenue, Irvine, CA 92606 Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 4 Website: www.seco-larm.com E-mail: firstname.lastname@example.org PITSW4 MiPB-A1x00Q_1012.docx SECO-LARM U.S.A., Inc.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project