- Computers & electronics
- Computer components
- Interface components
- Serial converters/repeaters/isolators
- User manual
advertisement
Microsoft Word - System 24 (MSC-24SE) Installation Guide....
http://dealers.savantav.com/portal/SavantSandbox/Guides/Sy...
Appendix A: Flow Control
The Savant Controller provides Serial Ports 1 and 2 (RTS/CTS) to manage flow control, the rate of data transmission between two devices. For example, the Savant Controller may transmit data at a faster rate than the other device can receive and process the data.
Using the RS-232 protocol control lines RTS (Request To Send) and CTS (Clear To
Send) to manage flow control, the Savant Controller sends a Request to Send frame
(RTS) to the other device. If the device answers with a Clear To Send frame (CTS), the
Savant Controller sends the data. After a successful exchange, the device replies with an acknowledgement frame (ACK).
28 of 49
Confidential 28
6/03/13 9:45 AM
Microsoft Word - System 24 (MSC-24SE) Installation Guide....
http://dealers.savantav.com/portal/SavantSandbox/Guides/Sy...
Appendix B: Matrix Switch Controller Ports and Pinouts
Controller Ports
Function Connector Type
Gigabit Ethernet RJ45
Serial RS-232/422/485 RJ45
IR Phoenix Push-In
Relays
GPIO
Long-Haul SPDIF
Firewire
USB-A
TOSLINK RCV
TOSLINK XMT
FXO
FXS
Phoenix Push-In
Phoenix Push-In
RJ45
1394A (6-pin)
USB-A
TOSLINK Optical
TOSLINK Optical
RJ11
RJ11
RJ45 Plug Pinouts
Number of Ports
3
8 (See pinouts below)
6 (See pinouts below)
4 (See pinouts below)
7 (See pinouts below)
1
1
1
3
1
1 (Reserved for future use)
1 (Reserved for future use)
29 of 49
1 RX+ 5 RXD
2 RX-
3 TX+
6 TX-/TXD
7 CTS
4 GND 8 RTS
!"#$: Pin 6 Jumper Select for RS-232 or RS-422
Important RS-232/422/485 Wiring Notes
! If you are using RJ-45 to DB-9 adapters not supplied by Savant be sure not to terminate any wires required for communication/control within the adapter.
Cut all unused wires to prevent the wires from shorting against each other.
! Ensure that all wires required for communication/control are not terminated in the connecter. Also, ensure that these unused wires are not shorting to each other, as they are still terminated in the RJ-45 connector on the controller side.
Confidential 29
6/03/13 9:45 AM
Microsoft Word - System 24 (MSC-24SE) Installation Guide....
http://dealers.savantav.com/portal/SavantSandbox/Guides/Sy...
Wiring RS-232 and RS-422 Connector Converters
If installers need to wire RJ45 to DB-9 connector converters that are specific to either
RS-232 or RS-422 protocols, but not both in the same connector, review the following:
30 of 49
RJ45 to DB-9 Connector Converter Pinouts (RS-232)
!"#$%&'(&: When RS-232 supports Request to Send/Clear to Send (RTS/CTS) signaling, only use the pins that are asterisked * for the pinout configuration. Refer to the table below.
7*
8*
9
3*
4
5*
6
DB9 Pin Color
1
2*
Orange
Green
Yellow
Black
Red
Blue
White
Brown
Not used
Signal Name
No connection
RXD
TXD
No connection
GND
No connection
RTS
CTS
No connection
RJ45 to DB-9 Connector Converter Pinouts (Null RS-232)
5
6
3
4
7
8
9
DB9 Pin Color
1 Orange
2 Yellow
Green
Black
Red
Blue
Brown
White
Not used
Signal Name
No connection
TXD
RXD
No connection
GND
No connection
CTS
RTS
No connection
Confidential 30
6/03/13 9:45 AM
Microsoft Word - System 24 (MSC-24SE) Installation Guide....
http://dealers.savantav.com/portal/SavantSandbox/Guides/Sy...
RJ45 to DB-9 Connector Converter Pinouts (RS-422)
4
5
6
7
8
9
2
3
DB-9 Pin Color
1 Orange
Yellow
Not used
Black
Red
Blue
Brown
White
Green
Signal Name
RX-
No connection
No connection
TX+
GND
RX+
No connection
No connection
TX-
Wiring a Cat5e Cable to a RJ45 Connector
If installers need to wire a Cat5e cable to a RJ45 connector, review the following:
RJ45 to EIA/TIA-568A (Cat5)
7
8
5
6
1
2
3
4
RJ45 Pin # EIA/TIA-568A (Cat5)
Wire Color
White/Green
Green
White/Orange
Blue
White/Blue
Orange
White/Brown
Brown
RJ45 – EIA/TIA-568B (Cat5)
7
8
5
6
1
2
3
4
RJ45 Pin # EIA/TIA-568B (Cat5)
Wire Color
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
Confidential 31
31 of 49 6/03/13 9:45 AM
Microsoft Word - System 24 (MSC-24SE) Installation Guide....
http://dealers.savantav.com/portal/SavantSandbox/Guides/Sy...
RS-232 Cat5 Matrix Switch Controller to DB9 Connections (Straight)
MSC
Pin Sig
Cat5 Cable
568A
1
2
White/Green
Green
3 White/Orange
4 GND Blue
5 RXD White/Blue
6 TXD Orange
7 CTS White/Brown
8 RTS Brown
RJ45 to DB9 Connections
RJ45 Wire
Pin Color
1 Blue
2 Orange
3 Black
4 Red
5 Green
6 Yellow
7 Brown
8 White
Comments
DB9
Pin
1 No Connection
2 RXD
3 TXD
4 No Connection
5 GND
6 No Connection
7 RTS
8 CTS
9 No Connection
RS-232 Cat5 Matrix Switch Controller to DB9 Connections (Null
Modem)
MSC
Pin Sig
Cat5 Cable
568A
1
2
White/Green
Green
3 White/Orange
4 GND Blue
5 RXD White/Blue
6 TXD Orange
7 CTS White/Brown
8 RTS Brown
RJ45 to DB9 Connections
RJ45 Wire
Pin Color
1 Blue
2 Orange
3 Black
4 Red
5 Green
6 Yellow
7 Brown
8 White
Comments
DB9
Pin
1 No Connection
2 RXD
3 TXD
4 No Connection
5 GND
6 No Connection
7 RTS
8 CTS
9 No Connection
RS-422/485 Cat5 Matrix Switch Controller to DB9 Connections
MSC
Pin Sig
Cat5 Cable
568A
1 RX+ White/Green
2 RXGreen
3 TX+ White/Orange
4 GND Blue
5 White/Blue
6 TXOrange
7 White/Brown
8 Brown
RJ45 to DB9 Connections
RJ45 Wire DB9
Pin Color
1 Blue
2 Orange
3 Black
4 Red
5 Green
6 Yellow
7 Brown
8 White
Comments
Pin
1 RX-
2 No Connection
3 No Connection
4 TX+
5 GND
6 RX+
7 No Connection
8 No Connection
9 TX-
Confidential 32
32 of 49 6/03/13 9:45 AM
Microsoft Word - System 24 (MSC-24SE) Installation Guide....
http://dealers.savantav.com/portal/SavantSandbox/Guides/Sy...
IR Port Layout and Pinouts (2x6 Phoenix Jack)
33 of 49
Top Row IR Signal Bottom Row IR Signal
1 IR1+ 4 IR4+
IR1IR4-
2 5
3
IR2+
IR2-
IR3+
IR3-
6
IR5+
IR5-
IR6+
IR6-
Relay and GPIO Port Pinouts (2x8 Phoenix Jack)
Pin #/
7
8
5
6
2
3
4
Top Row
1
Relay Pin #/
Bottom Row
Relay 1-A 1
Relay 1-B 2
Relay 2-A 3
Relay 2-B 4
Relay 3-A 5
Relay 3-B 6
Relay 4-A 7
Relay 4-B 8
GPIO
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
COM/GND
GPIO and Relay Voltages
GPIO
Input: The maximum GPIO input voltage is 28 VDC.
Output: A single GPIO port outputs a voltage from 3-12 VDC with a maximum current of 10mA when the voltage is at 3V, and 50mA or 150mA (depending on the CPU board) when the voltage is at 12 VDC.
Relay
A single Relay port can output up to a maximum of 30V DC with a maximum current of
1.0 A.
For additional information on GPIO and Relay output voltages and currents, contact: [email protected].
Confidential 33
6/03/13 9:45 AM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project