G104SN03.V5 - Beck Elektronik Display

G104SN03.V5 - Beck Elektronik Display
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
( ) Preliminary Specifications
( v ) Final Specifications
Module
10.4 Inch Color TFT-LCD
Model Name
G104SN03 V5
Customer
Date
Approved by
Date
Checked &
Approved by
/2
01
1/
11
Prepared by
2011/10/27
/3
Debbie Chiu
2011/10/27
General Display Business Division /
AU Optronics corporation
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
In
te
Note: This Specification is subject to change
without notice.
rn
al
U
se
O
nl
y
ShengHsun Lin
G104SN03 V5 rev.3.0
1/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
Contents
1. Operating Precautions.....................................................................................4
2. General Description .........................................................................................5
2.1 Display Characteristics...........................................................................................................5
2.2 Optical Characteristics ...........................................................................................................6
3. Functional Block Diagram ...............................................................................9
4. Absolute Maximum Ratings ..........................................................................10
4.1 Absolute Ratings of TFT LCD Module .................................................................................10
4.2 Absolute Ratings of Environment ........................................................................................10
5. Electrical Characteristics ..............................................................................11
5.1 TFT LCD Module .................................................................................................................. 11
5.2 Backlight Unit........................................................................................................................13
6. Signal Characteristic .....................................................................................14
1/
11
/3
6.1 Pixel Format Image ..............................................................................................................14
6.2 Scanning Direction ...............................................................................................................14
6.3 Signal Description ................................................................................................................15
6.4 The Input Data Format .........................................................................................................16
6.5 Interface Timing ....................................................................................................................17
6.6 Power ON/OFF Sequence ...................................................................................................18
01
7. Connector & Pin Assignment ........................................................................19
se
O
nl
y
/2
7.1 TFT LCD Module: LVDS Connector.....................................................................................19
7.2 LED Backlight Unit (CN2): Driver Connector ......................................................................19
7.3 LED Backlight Unit (CN4): Light bar Connector..................................................................20
rn
al
U
8. Reliability Test Criteria ..................................................................................21
9. Mechanical Characteristics ...........................................................................22
E
In
te
9.1 LCM Outline Dimension (Front View) ..................................................................................22
9.2 LCM Outline Dimension (Rear View)...................................................................................23
AT
10. Label and Packaging....................................................................................24
PR
O
M
10.1 Shipping Label (on the rear side of TFT-LCD display) ......................................................24
10.2 Carton Package .................................................................................................................24
or
11 Safety.............................................................................................................25
AU
O
C
on
f
id
e
nt
ia
lF
11.1 Sharp Edge Requirements.................................................................................................25
11.2 Materials .............................................................................................................................25
11.3 Capacitors...........................................................................................................................25
11.4 National Test Lab Requirement..........................................................................................25
G104SN03 V5 rev.3.0
2/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
Record of Revision
Version and Date
0.0
April 25, 2011
1.0
July 25, 2011
First draft specification
-
5
TBD
22
N/A
Update view angle and color coordinates
specification
5
Typical Power Consumption 2.5W
Typical Power Consumption 3.5W
13
Ivcc 0.12A
0.2A
Oct 27, 2011
5
Update 2D drawing.
Pvcc 1.44W
PLED1.92W
2.4W
1.95W
Weight 300g(typ)
Weight 280g(typ)
Update Shipping Label
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
In
te
rn
al
U
se
O
nl
y
/2
01
1/
11
/3
24
O
3.0
New Description
All
23
Aug 16, 2011
Old description
AU
2.0
Page
G104SN03 V5 rev.3.0
3/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
1. Operating Precautions
/3
11
1/
01
/2
y
nl
O
se
U
rn
al
In
te
E
AT
M
PR
O
or
lF
ia
nt
15)
16)
id
e
13)
14)
on
f
12)
C
11)
O
10)
Since front polarizer is easily damaged, please be cautious and not to scratch it.
Be sure to turn off power supply when inserting or disconnecting from input connector.
Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
When the panel surface is soiled, wipe it with absorbent cotton or soft cloth.
Since the panel is made of glass, it may be broken or cracked if dropped or bumped on hard surface.
To avoid ESD (Electro Static Discharde) damage, be sure to ground yourself before handling TFT-LCD Module.
Do not open nor modify the module assembly.
Do not press the reflector sheet at the back of the module to any direction.
In case if a module has to be put back into the packing container slot after it was taken out from the
container, do not press the center of the LED light bar edge. Instead, press at the far ends of the LED light
bar edge softly. Otherwise the TFT Module may be damaged.
At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT Module.
TFT-LCD Module is not allowed to be twisted & bent even force is added on module in a very short time.
Please design your display product well to avoid external force applying to module by end-user directly.
Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be
supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied
exemption.
Severe temperature condition may result in different luminance, response time and lamp ignition voltage.
Continuous operating TFT-LCD display under low temperature environment may accelerate lamp exhaustion and
reduce luminance dramatically.
The data on this specification sheet is applicable when LCD module is placed in landscape position.
Continuous displaying fixed pattern may induce image sticking. It’s recommended to use screen saver or shuffle
content periodically if fixed pattern is displayed on the screen.
AU
1)
2)
3)
4)
5)
6)
7)
8)
9)
G104SN03 V5 rev.3.0
4/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
2. General Description
This specification applies to the Color Active Matrix Liquid Crystal Display G104SN03 V5 composed of a TFT-LCD
display, a driver and power supply circuit, and a LED backlight system. The screen format is intended to support SVGA
(800(H) x 600(V)) screen and 16.2M (RGB 8-bits) or 262k colors (RGB 6-bits).
LED driving board for backlight unit is included in G104SN03 V5 and the LED unit is replaceable.
All input signals are LVDS interface and compatible with G104SN03 V1.
G104SN03 V5 designed with wide viewing angle; wide temperature and long life LED backlight (30k hrs) is well suited
for industial applications.
G104SN03 V5 is a RoHS product.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 oC condition:
Items
Unit
Specifications
Active Area
[mm]
211.2(H) x 158.4(V)
Screen Diagonal
[inch]
10.4
Pixels H x V
800x3(RGB) x 600
0.264 x 0.264
/3
[mm]
11
Pixel Pitch
R.G.B. Vertical Stripe
Display Mode
TN, Normally White
/2
01
1/
Pixel Arrangement
[Volt]
3.3 (typ.)
Typical Power Consumption
[Watt]
3.5W(ILED=25mA)
All black pattern
Weight
[Grams]
280g(typ.)
Physical Size
[mm]
236.0(H)x 176.9(V) x 5.7(D) (typ.)
In
te
rn
al
U
se
O
nl
y
Nominal Input Voltage VDD
AT
E
Electrical Interface
PR
O
16.2M / 262K colors
[oC]
o
[ C]
-20 to +70
-20 to +70
RoHS Compliance
AU
O
C
on
f
id
e
nt
ia
lF
Temperature Range
Operating
Storage (Non-Operating)
or
Support Color
RoHS Compliance
Anti-glare, Hardness 3H
M
Surface Treatment
1 channel LVDS
G104SN03 V5 rev.3.0
5/25
1
ith50cm
ingdstace
w
vew
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25 oC (Room Temperature):
Item
Unit
Conditions
Min.
Typ.
Max.
ILED= 25mA
190
230
White Luminance
[cd/m2]
(center point)
5 points
%
[msec]
[msec]
Viewing Angle
25
30
-
10
20
80
-
Rising + Falling
-
35
-
Horizontal
CR = 10
(Right)
(Left)
70
[degree]
[degree]
Vertical
CR = 10
(Upper)
(Lower)
50
60
-
0.563
0.593
0.623
0.321
0.351
0.381
70
80
60
Red x
70
0.321
Green x
Green y
0.351
0.545
Blue x
0.120
Blue y
0.082
0.150
01
0.28
0.575
/2
White y
y
0.30
O
nl
%
0.31
0.33
50
2,3
4
5
-
6
-
0.381
0.605
0.180
0.142
0.34
0.36
-
U
se
Note 1: Measurement method
0.112
1
50
[degree]
[degree]
White x
Color Gamut
500
-
Red y
Color / Chromaticity
Coordinates
(CIE 1931)
400
Falling
[msec]
-
/3
Response Time
Rising
75
11
Contrast Ratio
65
1/
Uniformity
Note
< 1 lux
PR
O
M
Environment
Center
E
Test Point
AT
Aperture
In
te
rn
al
Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent)
or
LCD Module
C
on
f
id
e
nt
ia
lF
equivalent
Measuring distance
Module Driving Equipment
AU
O
SR_3 or
G104SN03 V5 rev.3.0
6/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
Note 2: Definition of 5 points position (Display active area: 211.2mm (H) x 158.4mm (V))
W
W /4
W /4
W /4
W /4
H /4
1
2
H /4
3
H
H /4
4
5
H /4
Note 3: The luminance uniformity of 5 points is defined by dividing the minimum luminance values by the maximum test
point luminance
Minimum Brightness of five points
δW9 =
Maximum Brightness of five points
11
/3
Note 4: Definition of contrast ratio (CR):
1/
Brightness on the “White” state
01
Contrast ratio (CR)=
/2
Brightness on the “Black” state
se
O
nl
y
Note 5: Definition of response time:
U
The output signals of photo detector are measured when the input signals are changed from “White” to “Black”
Tf
AT
M
PR
O
100
90
White
lF
or
Optical
Black
White
10
0
AU
O
C
on
f
id
e
nt
ia
response
Tr
E
%
In
te
90% of amplitudes. Please refer to the figure as below.
rn
al
(falling time) and from “Black” to “White” (rising time), respectively. The response time interval is between 10% and
G104SN03 V5 rev.3.0
7/25
iew
10,ahescrnte,ovra18
ngalisthem
aurentofcrastio"
V
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
Note 6: Definition of viewing angle
0° horizontal and 180°
vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as below: 90° (θ) horizontal
left and right, and 90° (Φ) vertical high (up) and low (down). The measurement direction is typically perpendicular to the
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
In
te
rn
al
U
se
O
nl
y
/2
01
1/
11
/3
display surface with the screen rotated to its center to develop the desired measurement viewing angle.
G104SN03 V5 rev.3.0
8/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
3. Functional Block Diagram
The following diagram shows the functional block of the 10.4 inch color TFT/LCD module:
Timing Controller
Connecter
6/8 bits Sel
DPS
DC Power
Panel
Controller
Gate Driver IC
LVDS
receiver
LVDS 1ch
DC/DC
converter
TFT-LCD
800x(3)x600
Pixels
Source Driver IC
RSDS
Generate
Gamma
Voltage
Light Bar
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
In
te
rn
al
U
se
O
nl
y
/2
01
1/
11
/3
DC Power
G104SN03 V5 rev.3.0
9/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
4. Absolute Maximum Ratings
4.1 Absolute Ratings of TFT LCD Module
Item
Symbol
Min
Max
Unit
Logic/LCD drive Voltage
Vin
-0.3
+4.0
[Volt]
4.2 Absolute Ratings of Environment
Item
Symbol
Min
Max
Unit
Operation Humidity
HOP
5
90
[%RH]
Operating Temperature
TOP
Storage Temperature
-20
TST
Storage Humidity
+70
-20
HST
[oC]
+70
5
Note: Maximum Wet-Bulb should be 39 C and no condensation.
[ C]
o
[%RH]
90
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
In
te
rn
al
U
se
O
nl
y
/2
01
1/
11
/3
o
G104SN03 V5 rev.3.0
10/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
5. Electrical Characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Symbol
Parameter
Min
Typ
Max
Units
3.0
3.3
3.6
[Volt]
VDD
Logic/LCD Drive
Voltage
IDD
VDD Current
-
320
-
[mA]
Irush
LCD Inrush Current
-
-
1.5
[A]
PDD
VDD Power
-
1.06
-
[Watt]
-
100
[mV]
p-p
VDDrp
Allowable Logic/LCD
Drive Ripple Voltage
-
Remark
All Black Pattern
(VDD=3.3V, at 60Hz)
Note 1
All Black Pattern
(VDD=3.3V, at 60Hz)
All Black Pattern
(VDD=3.3V, at 60Hz)
Note 1: Measurement condition:
D6
D5
D2
D1
Q3
AO6402
1K
11
O
3.3V
90%
ia
nt
10%
0.47ms+ 10%
VDD rising time
AU
O
C
on
f
id
e
0V
lF
or
PR
O
M
AT
E
In
te
C2
1uF/25V
se
0.01uF/25V
47K
U
VR1
R2
1
/2
y
nl
S
C3
rn
al
2
Q3
AO6402
G
+12.0V
SW MAG-SPST
01
D1
D2
D5
D6
R2
(LCD Module Input)
1/
C1
1uF/16V
1K
SW1
VDD
VCC
G
R1
47K
(High to Low)
Control
Signal
F1
S
/3
+3.3V
G104SN03 V5 rev.3.0
11/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when VDD is off.
Symbol
Item
Min.
Typ.
Max.
Unit
Remark
VTH
Differential Input High Threshold
-
-
100
[mV] VCM=1.2V
VTL
Differential Input Low Threshold
100
-
-
[mV] VCM=1.2V
Input Differential Voltage
100
400
600
[mV]
1.125
1.25
1.375
[V]
|VID|
Differential Input Common Mode Voltage
VICM
VTH/VTL=+-100mV
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
In
te
rn
al
U
se
O
nl
y
/2
01
1/
11
/3
Note: LVDS Signal Waveform.
G104SN03 V5 rev.3.0
12/25
Product Specification
(R
o
(
G104SN03 V5
AU OPTRONICS CORPORATION
5.2 Backlight Unit
5.2.1 Parameter guideline for LED
Following characteristics are measured under a stable condition using an inverter at 25
om Temperature):
Symbol
Parameter
Min.
Typ.
Max.
VCC
Input Voltage
10.8
12
12.6
IVCC
Input Current
-
0.2
-
PVCC
Power Consumption
-
2.44
-
FPWM
Dimming Frequency
200
-
10K
Dimming
Swing Voltage
3
3.3
5.5
Dimming duty cycle
5
-
100
%
Dimming Voltage
0.6
3
[Volt]
Dimming Range
30
100
%
IF
LED Forward Current
-
25
-
[mA]
Ta = 25oC
VF
LED Forward Voltage
-
26
29.2
[Volt]
IF = 25mA, Ta = 25oC
Operation Life
-
25,000
30,000
-
100% Brightness
[Hz]
PWM Dimming
[Volt]
[Watt]
/3
1.95
[Watt]
Analoge Dimming
IF = 25mA, Ta = 25oC
LED total Power
Ta= 60oC RH<60%
11
-
100% Brightness
1/
LED Power Consumption
[A]
[Volt]
01
PLED
Remark
Hrs
IF=25mA Tj<70 C
o
/2
Dimming
Unit
y
Note 1: Ta means ambient temperature of TFT-LCD module.
O
nl
Note 2: VCC, IVCC, Irush LED, PVCC are defined for LED backlight.(100% duty of PWM dimming)
se
Note 3: IF, VF are defined for one channel LED. There are three LED channel in back light unit.
rn
al
U
Note 4: If G104SN03 V5 module is driven by high current or at high ambient temperature & humidity condition. The
operating life will be reduced.
In
te
Note 5: Operating life means brightness goes down to 50% initial brightness. Minimum operating life time is estimated
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
data.
G104SN03 V5 rev.3.0
13/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship between input signal and LCD pixel format.
1st
2nd
Pixel
G
B
R
G
B
R
G
B
R
G
B
R
G
B
R
G
B
R
G
B
R
G
B
/2
01
Lin
R
Pixel
/3
600th
800th
Pixel
11
Line
Pixel
1/
1st
799th
O
nl
y
6.2 Scanning Direction
or
PR
O
M
AT
E
In
te
rn
al
U
se
The following figures show the image seen from the front view. The arrow indicates the direction of scan.
Fig. 2 Reverse scan (Pin4, DPS = High)
AU
O
C
on
f
id
e
nt
ia
lF
Fig. 1 Normal scan (Pin4, DPS = Low or NC)
G104SN03 V5 rev.3.0
14/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
6.3 Signal Description
The module uses a LVDS receiver embedded in AUO’s ASIC. LVDS is a differential signal technology for LCD
interface and a high-speed data transfer device.
(1)Input signal interface
Pin no
Symbol
1
VDD
3
GND
2
+3.3 V power supply
VDD
4
6
Ground
Reverse Scan Function [H: Enable; L/NC:Disable]
RxIN0-
LVDS receiver signal channel 0
GND
Ground
LVDS Differential Data Input (R0, R1, R2, R3, R4, R5, G0)
RxIN0+
7
8
9
RxIN1-
LVDS receiver signal channel 1
GND
Ground
LVDS Differential Data Input (G1, G2, G3, G4, G5, B0, B1)
RxIN1+
10
11
RxIN2-
LVDS receiver signal channel 2
13
GND
Ground
CKIN-
16
GND
Ground
RxIN3-
y
RxIN3+
LVDS Differential Data Input (R6, R7, G6, G7, B6, B7, RSV)
SEL68
6/8 bits LVDS input setting [H: 8 bits; L/NC:6 bits]
U
20
Reserved for AUO internal test. Please treat it as NC.
se
Reserved
rn
al
19
nl
18
LVDS receiver signal channel 3, NC for 6 bit LVDS Input
O
17
11
LVDS receiver signal clock
CKIN+
1/
15
01
14
/3
LVDS Differential Data Input (B2, B3, B4, B5, HS, VS, DE)
RxIN2+
/2
12
Etc.
+3.3 V power supply
DPS
5
Function
In
te
Note 1: Input Signals shall be in low status when VDD is off.
AT
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
Note 3: RSV means “Reserved”.
E
Note 2: High stands for “3.3V”, Low stands for “0V”, NC means “No Connection”.
G104SN03 V5 rev.3.0
15/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
6.4 The Input Data Format
SEL68 =“Low” or “NC” for 6 bits LVDS Input
SEL68 = “High” for 8 bits LVDS Input
NS-like format
Note1: Please follow PSWG.
Note2: R/G/B data 7:MSB, R/G/B data 0:LSB
O
C
E
AT
M
PR
O
or
lF
ia
nt
11
/3
Remark
1/
Red-pixel Data
/2
01
For 8Bits LVDS input
MSB: R7 ; LSB: R0
rn
al
U
se
O
nl
y
For 6Bits LVDS input
MSB: R5 ; LSB: R0
In
te
Description
Red Data 7
Red Data 6
Red Data 5
Red Data 4
Red Data 3
Red Data 2
Red Data 1
Red Data 0
Green Data 7
Green Data 6
Green Data 5
Green Data 4
Green Data 3
Green Data 2
Green Data 1
Green Data 0
Blue Data 7
Blue Data 6
Blue Data 5
Blue Data 4
Blue Data 3
Blue Data 2
Blue Data 1
Blue Data 0
LVDS Data Clock
Data Enable Signal
id
e
on
f
Signal Name
R7
R6
R5
R4
R3
R2
R1
R0
G7
G6
G5
G4
G3
G2
G1
G0
B7
B6
B5
B4
B3
B2
B1
B0
RxCLKIN
DE
Green-pixel Data
For 8Bits LVDS input
MSB: G7 ; LSB: G0
For 6Bits LVDS input
MSB: G5 ; LSB: G0
Blue-pixel Data
For 8Bits LVDS input
MSB: B7 ; LSB: B0
For 6Bits LVDS input
MSB: B5 ; LSB: B0
When the signal is high, the pixel data
shall be valid to be displayed.
AU
Note: Output signals from any system shall be low or Hi-Z state when VDD is off.
G104SN03 V5 rev.3.0
16/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
6.5 Interface Timing
6.5.1 Timing Characteristics
Signal
Symbol
Clock Frequency
1/ TClock
Vertical
Section
Horizontal
Section
Period
TV
Active
TVD
Blanking
TVB
Period
TH
Active
THD
Blanking
THB
Frame Rate
Note : DE mode.
Min.
Typ.
30
F
Max.
40
Unit
50
608
628
1024
--
600
--
8
28
424
960
1056
1060
--
800
--
160
256
260
50
60
75
MHz
TLine
TClock
Hz
01
1/
11
Input Timing Definition ( DE Mode)
TCLOCK
/3
6.5.2 Input Timing Diagram
Pixel
2
Pixel
3
Pixel
N-1
se
Pixel
1
U
Invaild
Data
Pixel
N
Invaild
Data
Pixel
1
DE
In
te
rn
al
Input
Data
O
nl
y
/2
DOTCLK
THD
TH
PR
O
M
AT
E
THB
DE
TVB
TV
AU
O
C
on
f
id
e
nt
ia
lF
or
TVD
G104SN03 V5 rev.3.0
17/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
6.6 Power ON/OFF Sequence
01
1/
11
/3
VDD power and lamp on/off sequence is as below. Interface signals are also shown in the chart. Signals from
any system shall be Hi-Z state or low level when VDD is off.
10
or
ia
T9
lF
T8
nl
O
se
U
[ms]
-
[ms]
10
-
-
[ms]
[ms]
[ms]
[ms]
--
--
10
[ms]
0
16
50
[ms]
1000
-
10
-
nt
--
50
-
T12
T13
[ms]
-
110
T11
10
--
Units
0
T10
id
e
on
f
--
AT
PR
O
M
10
Max.
rn
al
T5
0.5
-
In
te
200
T7
C
40
T3
T4
O
30
0.5
T2
AU
Typ.
E
T1
Min.
y
Value
Parameter
T6
/2
Power ON/OFF sequence timing
-
--
-
--
10
-
[ms]
[ms]
[ms]
[ms]
The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn
off the power when you plug the cable into the input connector or pull the cable out of the connector.
G104SN03 V5 rev.3.0
18/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
7. Connector & Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of accommodating
the following signals and will be following components.
7.1 TFT LCD Module: LVDS Connector
Connector Name / Designation
Signal Connector
Connector Model Number
MSB24013P20HA or compatible
Manufacturer
STM or compatible
P24013P20 or compatible
Pin No.
Symbol
Pin No.
Symbol
3
GND
4
DPS
1
VDD
2
VDD
5
RxIN0-
6
RxIN0+
9
RxIN1+
10
GND
13
GND
14
RxCKIN-
18
RxIN3+
GND
12
RxCKIN+
16
19
RSV
20
17
RxIN3-
GND
11
15
RxIN2+
1/
RxIN2-
RxIN1-
SEL68
01
11
8
se
O
nl
y
7.2 LED Backlight Unit (CN2): Driver Connector
/2
7
/3
Adaptable Plug
Lamp Connector
Connector Model Number
3808K-F05N-02R or compatible
rn
al
U
Connector Name / Designation
Entery
In
te
Manufacturer
AT
Pin2
GND
lF
On/OFF
nt
ia
Pin3
Dimming
id
e
Pin4
NA
12V input
GND
5V-ON,0V-OFF
PWM/Analog
AU
O
C
on
f
Pin5
Description
or
VCC
M
Symbol
PR
O
Pin No.
Pin1
H208K-P05N-02B or compatible
E
Mating Model Number
G104SN03 V5 rev.3.0
19/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
7.3 LED Backlight Unit (CN4): Light bar Connector
Connector Name / Designation
Lamp Connector
Manufacturer
Entery or compatible
Connector Model Number
Entery H203K-D04N-02Bor compatible
Mating Model Number
Entery 3800K-F04N-03Ror compatible
Symbol
Cable color
Signal Name
1
AN
RED
LED anode
2
CA1
BLACK
LED Cathode 1
3
CA2
WHITE
LED Cathode 2
4
CA3
BLUE
LED Cathode 3
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
In
te
rn
al
U
se
O
nl
y
/2
01
1/
11
/3
Pin #
G104SN03 V5 rev.3.0
20/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
8. Reliability Test Criteria
Items
Temperature
Humidity Bias
High Temperature
Operation
Low Temperature
Operation
Hot Storage
Required Condition
Note
40 oC /90%,300Hr
70 C, 300Hr (center point of panel surface)
o
-20 oC, 300Hr
70 C, 300 hours
o
Cold Storage
-20 C, 300 hours
o
Hot Start Test
Cold Start Test
Shock Test
(Non-Operating)
-20 oC /30 min ,60 oC /30 min ,100cycles, 40 oC minimun ramp rate
70 oC /1 Hr min.
-20 C /1 Hr min.
o
power on/off per 5 minutes, 5 times
power on/off per 5 minutes, 5 times
50G,20ms,Half-sine wave,(+-X,+-Y,+-Z)
Vibration Test
(Non-Operating)
1.5G, 10~200~10Hz, Sine wave
On/off test
On/10 sec, Off/10 sec, 30,000 cycles
30mins/axis, 3 direction (X, Y, Z)
/3
Thermal Shock
Test
1/
11
Contact : ± 8KV/ operation, Class B
ESD
30-230 MHz, limit 40 dBu V/m, 230-1000 MHz, limit 47 dBu V/m
y
/2
EMI
Note 1
01
Air : ± 15KV / operation, Class B
se
In
te
E
The reliability test is performed only to examine the TFT-LCD module capability.
To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity for 24
hours at least in advance.
AU
O
C
on
f
id
e
nt
ia
lF
or
test.
AT
Each test is done by new TFT-LCD module. Don’t use the same TFT-LCD module repeatedly for reliability
M
Water condensation is not allowed for each test items.
PR
O
U
Note2:
Self-recoverable. No hardware failures.
rn
al
.
O
nl
Note1: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
G104SN03 V5 rev.3.0
21/25
on
f
C
or
lF
ia
nt
id
e
M
PR
O
E
AT
rn
al
In
te
O Dimension (Front View)
9.1 LCM Outline
U
9. Mechanical
Characteristics
A
se
U
AU OPTRONICS CORPORATION
y
nl
O
Product Specification
/3
11
1/
01
/2
G104SN03 V5
22/25
G104SN03 V5 rev.3.0
O
U
on
f
C
or
lF
ia
nt
id
e
M
PR
O
E
AT
rn
al
In
te
9.2 LCM Outline
Dimension (Rear View)
A
se
U
AU OPTRONICS CORPORATION
y
nl
O
Product Specification
/3
11
1/
01
/2
G104SN03 V5
23/25
G104SN03 V5 rev.3.0
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
10. Label and Packaging
10.1 Shipping Label (on the rear side of TFT-LCD display)
V5
1/
11
/3
10.2 Carton Package
O
nl
y
/2
01
LCD Module
Carton
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
NOTE :
1. Max. Capacity : 30 LCD Modules/Carton.
2. Max. Weight : 13Kg/Carton.
3. Meas : 448 mm*402mm*350mm.
EPP Cushion
In
te
rn
al
U
se
Anti-Static
Bag
G104SN03 V5 rev.3.0
24/25
Product Specification
G104SN03 V5
AU OPTRONICS CORPORATION
11 Safety
11.1 Sharp Edge Requirements
There will be no sharp edges or comers on the display assembly that could cause injury.
11.2 Materials
11.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are
used, they will be reviewed and approved by the responsible AUO toxicologist.
11.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in
the module will complete the flammability rating exception approval process.
The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability
rating will be printed on the printed circuit board.
11.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from
1/
11
/3
being inserted backwards.
y
nl
The display module will satisfy all requirements for compliance to:
/2
01
11.4 National Test Lab Requirement
U.S.A. Information Technology Equipment
AU
O
C
on
f
id
e
nt
ia
lF
or
PR
O
M
AT
E
In
te
rn
al
U
se
O
UL 60950-1 second edition
G104SN03 V5 rev.3.0
25/25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising