KDA 212 Amplifier
preliminary
KDA 212 Amplifier
2 CHANNEL DISTRIBUTED AUDIO POWER AMPLIFIERS
KEY FEATURES
UL 2041 rating for plenum space installation
Built-in K8 digital audio distribution system input
Simple LED diagnostics
Remote control and monitoring over K8 bus system
Tile bridge accessory for ceiling installation
Flange mounting ears allow flexible mounting locations
Single channels drive down to 2-Ohms for parallel
distributed systems
Alternative to 70/100V systems
Analog line level inputs summed to K8 digital inputs
Daisy chain K8 digital input bus eliminates hubs and
switches
Channel pair bridges up to 3 times the individual channel
power rating
PRODUCT DESCRIPTION
The plenum rated KDA series amplifiers enable
the possibility of designing distributed amplified
systems through the use of a single Cat 5 cable for
digital audio distribution as well as remote control
and monitoring with the K8 digital audio distribution
system. Applications for KDA amplifiers include ceiling
placement to drive multiple divisible conference
rooms and meeting facilities, bridged and placed
near reinforcement loudspeakers to create amplified
systems out of passive loudspeakers and easy location
in conference room furniture to drive media or
overhead loudspeakers. Multiple KDA amplifiers may
be daisy chained together eliminating the multiple
long copper runs associated with 70/100V systems
and allowing easy facility expansion with no concern
for induced noise or ground loops. KDA amplifiers offer
an efficient and effective alternative to creating large
area multizone systems in new facilities by eliminating
amplifier floor space requirements and ensuring
quality operation.
TECHNICAL SPECIFICATIONS
Power Requirements
Power supply
Operating temperature
Weight
External dimensions
100-230V (+/- 15%)
0°C, 45°C (32°F, 113°F)
2 kg, 4.4 lbs
8.62”(W) x 2.99”(H) x 6.1”(D)
Audio Section
Bandwith (1W, 8 Ohm) 20 Hz - 20kHz +/-0.2dB
S/N ratio
>110 db
Distortion THD
Max. < 1% from 1W to full power
(typically <0.05%)
Inputs
Balanced to ground, 2 x Phoenix 3.81,
3-pin
K8 digital audio bus, RJ45 in/thru
Gain
Outputs
-60 ... +10dB in 15 steps
Phoenix 5.08, 4-pin
KDA 212 Amplifier
2 CHANNEL DISTRIBUTED AUDIO POWER AMPLIFIERS
OUTPUT POWER SPECIFICATIONS (Watts per channel, both channels driven, 1kHz, 1% THD+N
mains voltage
230V
120V
100V
2 Ohm
185
170
130
Stereo Mode
4 Ohm
120
110
85
Bridged Mode
4 Ohm
430
380
300
K8 CONTROL FEATURES
TECHNICAL SPECIFICATIONS
Control Functions
via K8
Link
Power on/off, input gain, signal
routing
Monitoring
Functions via K8:
Load impedance, temperature,
input signal level, output voltage,
output current
Additional Amplifier Load short shutdown and self
Protection:
recovery, thermal limiting, DC
and infrasonic and ultrasonic
frequency signal protection
K8 loop through, RJ-45, passive
bus coupling
K8 / Analog Routing
2 x Rotary switch, behind front
panel, software override
K8 / Analog input gain 2 x Rotary switch, behind front
panel, software override
Control
Directly via K8 bus
Termination Switch
4-position DIP
Digital Audio Format
48 kHz sampling rate, 24 bit,
proprietary
Latency
½ millisecond worst case, analogue in to analogue out
K8 Rear Panel Indicators Sync, Wink
MECHANICAL DRAWING
K+H Vertriebs- und Entwicklungsgesellschaft mbH
Auf dem Kessellande 4A
30900 Wedemark
Germany
170309
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising