URD-750
URD-750
Stereo Radio, CD Player with Dual Alarm Clock
Read instructions carefully before using the unit
Bitte vor Inbetriebnahme sorgfälltig lessen
Avant de metre en service votre appareil, lisez attentivement ces instructions
* ENGLISH *
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD DO NOT USE THIS PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE. DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
This lightning flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user
to
the
presence
of
dangerous voltage within
the product’s enclosure
that may be of sufficient
magnitude to constitute a
risk of electric shock to
persons present.
Warning: to reduce the
risk of electric shock, do
not remove or open the
casing of the product.
There are no user serviceable part inside.
Refer
servicing
to
qualified
service
personnel.
1.
2.
3.
4.
5.
6.
7.
The
exclamation
point
within an equilateral triangle
is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions in
the literature accompanying
the appliance.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufactures
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at the plugs,
convenience receptacles, and at the point where it exits from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug the apparatus during lightening storms or when unused for long periods of time.
13. Refer all servicing to qualified personnel. Servicing is required when the apparatus has
been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
14. This appliance should not be exposed to dripping or splashing water and no objects
filled with liquids such as vases should be placed on apparatus.
Dripping warning: The products should not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on the product.
Ventilation warning: The normal ventilation of the product should not be impeded for intended
use.
1
LOCATION OF CONTROLS AND INDICATORS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
POWER ‘On’ LED Indicator
ALARM.OFF/POWER Button
CLK-ADJ/PROG. Button
RADIO/BAND Button
ALARM 1 ON/OFF Button
CD Compartment
CD Door Open/Close
SNOOZE Button
SLEEP Button
ALARM SET/DISPLAY Button
ALARM 2 ON/OFF Button
TIME-DN/F.REW (Time down/CD fast
reverse search) Button
CD STOP Button
CD PLAY/PAUSE Button
TIME-UP/F.FWD (Time up/CD fast
forward search) Button
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
2
SLEEP Indicator
Radio Tuning Window
TUNING Control
FM Indicator
LED Display
Battery Compartment
AUX Jack
Phones Jack
Dimmer Control (optional)
ALARM 1 Indicator
VOLUME Control
ALARM 2 Indicator
AM/PROG. Indicator
AC Power Cord
FM Wire Antenna
Speakers
Power Source
This system is designed to operate on 230VAC 50Hz house current only. Connecting this
system to any other power source may cause damage to the system and such damage is not
covered by your warranty.
Note: The system has polarized AC plug with one wide blade and one narrow blade. The plug
will only fit into matching polarized AC outlets.
Battery Back Up System
This unit uses a single 9-Volt battery (not included) to maintain the time and alarm settings in
event that it is accidentally unplugged, or you experience a temporary power failure. We
recommend that you install a well-known brand of Alkaline battery for longest life and best
performance. To keep the battery back up system operational you should install a new battery
every 6 to 9 months. Some people find it convenient to replace the back up batteries in their
alarm clocks, clock radios, and smoke detectors too, at the beginning and end of Daylight
Saving Time.
OPERATING INSTRUCTIONS
Setting The Correct Time And Day
NOTE: Connect the power cord to your AC outlet. Make sure to use an outlet that is always ‘live’.
Do not use an outlet that is controlled by a wall switch.
1. When the unit is plugged in for the first time, the clock display will begin flashing “0:00”
(AM).
2. Press and hold the CLK-ADJ/PROG. button for at least two seconds until only the Hour digits
continue to flash.
3. While the Hour digits are flashing press the TIME-DN/F.REW or TIME-UP/F.FWD buttons
repeatedly to set the clock to the correct Hour.
4. When the correct hour is flashing, press the CLK-ADJ/PROG. button again. The Minute
digits begin flashing.
5. While the Minute digits are flashing press the TIME-DN/F.REW or TIME-UP/F.FWD buttons
repeatedly to set the clock to the correct Minutes.
6. Press the CLK-ADJ/PROG. button. The Day indicator “ d:1 ” begins to flash.
7. While the day indicator is flashing, press the TIME-DN/F.REW or TIME-UP/F.FWD buttons
repeatedly to set the display to the correct ‘Day’. (1 = Monday, 2 = Tuesday, etc.)
8. When the correct ‘day’ (digit) appears on the display press the CLK-ADJ/PROG. button once
more to exit the clock-setting mode. The display stops flashing and returns to the correct time
and the clock begin to run.
IMPORTANT: After you press the CLK-ADJ/PROG. button you must make your time
adjustments within 10 seconds while the display is flashing. After 10 seconds the display stops
flashing and no time adjustments can be made. If this occurs you must begin with Step 2
above and start the time adjustment process again.
Listening To The Radio
1. Press the ALARM OFF/POWER button on the top panel to turn the unit ‘On’. The POWER
LED indicator comes on.
2. Press the RADIO/BAND button to select the Radio function. Either the AM/PROG. or the FM
indicator will come on to confirm which band is selected. Press the RADIO/BAND button
again to repeatedly switch between the AM and FM bands.
3. Rotate the TUNING control on the right side panel to tune to the desired station.
3
4. Rotate the VOLUME control on the left side panel to adjust the volume level.
5. When you are finished listening press the ALARM OFF/POWER button to turn the unit ‘Off’.
The POWER LED indicator goes off.
Antenna Information
AM
The AM ferrite bar antenna is inside the cabinet. If AM reception is unsatisfactory try turning the
entire unit slightly until you find the direction that provides the best reception for the desired
station.
FM
Make sure the FM lead wire antenna is extended to it’s full length. You may have to vary the
direction of the wire antenna to find the position that provides the best reception.
Playing Compact Discs
NOTE: Although this CD player can read CD-R and CD-RW discs, in addition to normal CDs,
however the playability of CD-R/RW discs may be affected by the type of software that was used
to create the discs, as well as the quality and condition of the blank media you are using. 100%
playability cannot be guaranteed. This is not an indication of a problem with the player.
Normal Playback
1. Press the ALARM OFF/POWER button to switch the unit ‘On’. The POWER LED indicator
comes ‘On’.
2. Press the CD PLAY/PAUSE button to enter CD playing mode.
3. Press on the CD door in the area marked OPEN/CLOSE to open the door. If you have not
already done so, remove the ‘dummy CD’ transit protection card from the CD player and
discard it
4. Place your disc on the center spindle with the printed label side facing up. Press down near
the center of the disc to make sure it is firmly ‘seated’ on the spindle, press OPEN/CLOSE to
close the CD door.
5. Two dashes “cd- -“ flash while the player reads the table of contents of the disc.
The display will show the total number of tracks for a few seconds and then return to the
correct time.
To see the track number at any time during playback press the ALARM SET/DISPLAY button.
The track number will appear for several seconds and then the display returns to the correct
time.
Note: If the disc is inserted incorrectly, or if the disc is badly scratched and cannot be read by
the player, “cd00”will appear on the display for a few seconds, and then the display returns to
the correct time.
6. Press the CD PLAY/PAUSE button to begin playback.
The display will briefly show “cd: 1” (Track 1) and playback on track 1 begins.
After a few seconds the display returns to the correct time.
7. To pause briefly during playback press the CD PLAY/PAUSE button.
The two dots “ : ” in the middle of the display flashes briefly and the sound stops, but the disc
continues to spin. Press the CD PLAY/PAUSE button again to cancel pause and resume
playback.
8. To skip forward or backward to other tracks repeatedly press the TIME-DN/F.REW or
TIME-UP/F.FWD buttons until the desired track number appears in the display. Playback will
begin on the selected track.
4
9. To stop playback at any time press the CD STOP button. After the last track has played the
disc stops automatically. Press the OPEN/CLOSE button to open the CD door and remove
your disc.
Important note:
You cannot stop CD playback by pressing the ALARM OFF/POWER button. You must press
the CD STOP button to stop CD playback first, and then you can press the ALARM
OFF/POWER button to shut the power off.
To Start Playback From A Specific Track
Load your disc and wait until the display shows the total number of tracks.
Press the TIME-DN/F.REW or TMIE-UP/F.FWD buttons to select the desired track.
While the track number is still flashing press the CD PLAY/PAUSE button. Playback will begin
on the selected track and continue until the end of the disc.
High Speed Music Search
You can search rapidly forward or backward within a track to locate a specific musical passage.
Depress and hold the TIME-DN/F.REW or TMIE-UP/F.FWD buttons to begin high speed search.
The display will show the current track and the player moves rapidly forward or backward. When
you reach the desired passage release the TIME-DN/F.REW or TMIE-UP/F.FWD buttons and
normal playback resumes.
Note: The volume level is automatically reduced during high speed music search.
Programmed Playback
The CD player in this unit has a 20 track programmable memory which allows you to program
any disc to play just the tracks you want to hear in the exact order that you want to hear them.
You may program a track or tracks to play more than once if desired.
Note: Programming can only be done while the player is in the Stop mode. If a disc is playing
press the CD STOP button to stop playback before performing the programming steps below.
1. Turn the unit ‘On’, press the CD PLAY/PAUSE button to select CD function and load the
desired disc in the player. Wait until the player reads the disc and the display shows the total
track number.
2. Press the CLK.ADJ/PROG. button. The AM/PROG. indicator and the Program Number “01”
flash in the display, indicating that you can select the first track to be programmed.
3. Press the TIME-DN/F.REW or TMIE-UP/F.FWD buttons to select the first track. The desired
track number flashes on the display. Example: Track “7”.
4. Press the CLK-ADJ/PROG. button again. The selected track is entered in program memory
number 01 and the display advances to “02” flashes indicating that you can select the next
track to be programmed.
5. Repeat step 3 and 4 to program up to 20 tracks in the memory.
6. After you have programmed all the desired tracks press the CD PLAY/PAUSE button to
begin programmed playback the AM/PROG. indicator stops flashing and remains “on”.
Playback will begin on the first track you programmed and continue until all programmed
tracks have been played.
As each programmed track starts playing the display will briefly show the track number being
played and then return to the correct time.
Notes:
y After all programmed tracks have played the player stops but the program remains in the
memory.
5
Press the CLK.ADJ/PROG. button and then the CD PLAY/PAUSE button to begin
programmed playback again.
y To clear the program from the memory after the disc stops, press the CLK.ADJ/PROG.
button and then press the STOP button.
Opening the CD door, pressing the ALARM OFF/POWER button to shut the unit off, or by
switching to the RADIO function also clear the program.
Adjusting The Wake-Up Times
This clock radio has two separate wake-up alarms that can be set and used independently. To
set or adjust the wake-up times please proceed as follows:
1. Depress and hold the ALARM SET/DISPLAY button for at least two seconds until just the
Hour digits and the AL1(Alarm 1) indicator are flashing.
2. While the Alarm 1 Hour digits are flashing press the TIME-DN/F.REW or TMIE-UP/F.FWD
buttons repeatedly to set the display to the correct wake-up hour. Example: 7:00 AM
3. When the correct wake-up hour is flashing press the CLK. ADJ/PROG. button again. The
Hour digits stop flashing and the minute digits begin to flash.
4. While the Minute digits are flashing press the TIME-DN/F.REW or TMIE-UP/F.FWD buttons
repeatedly to set the display to the correct wake-up minute.
5. When the desired Alarm 1 wake-up time is showing on the display, press the CLK.
ADJ/PROG. button to store the Alarm 1 wake-up time in the timer memory.
The AL2 (Alarm 2) indicator and the Alarm 2 Hour digits begin flashing.
Note: If you do not need to adjust the Alarm 2 wake up time you may just wait 10 seconds.
After 10 seconds the Alarm 2 display stops flashing and the clock returns to the correct time.
6. While the Alarm 2 Hour digits are flashing press the TIME-DN/F.REW or TMIE-UP/F.FWD
buttons repeatedly to set the display to the correct wake-up hour. Example: 9:00 AM
7. When the correct wake-up hour is flashing press the CLK. ADJ/PROG. button again. The
Hour digits stop flashing and the minute digits begin to flash.
8. While the Minute digits are flashing press the TIME-DN/F.REW or TMIE-UP/F.FWD buttons
repeatedly to set the display to the correct wake-up minute.
9. When the desired Alarm 2 wake-up time is showing on the display, press the CLK.
ADJ/PROG. button to store the Alarm 2 wake-up time in the timer memory. The display stops
flashing and returns to the correct time. The Alarm 2 indicator disappears.
IMPORTANT: After you press the CLK. ADJ/PROG. button you must make your wake-up time
adjustments within 10 seconds while the wake-up time display is flashing. After 10 seconds the
wake-up time display stops flashing, the display returns to the correct time, and no wake-up
time adjustments can be made. If this occurs you must begin with Step 1 above and start the
wakeup time adjustment process again.
Setting The Alarms / Selecting The Wake-up Mode
After you have adjusted the wake-up times on one or both alarms you must press the respective
ALARM 1 and/or ALARM 2 buttons one, two or three times, to activate the alarms and select
the wake-up mode.
The color of the AL1 and AL2 indicators will change according to the wake-up mode that you
select - Buzzer, Radio, or CD.
NOTE: Whichever wake-up mode you select - Buzzer, Radio, or CD – will apply to both alarms.
Press the ALARM 1 or ALARM 2 button once.
The AL indicator is Red. This indicates the Wake To Buzzer mode is selected and the alarm
is ‘On’.
6
Press the ALARM 1 or ALARM 2 button twice.
The AL indicator is Green. This indicates the Wake To Radio mode is selected and the
alarm is ‘On’.
Press the ALARM 1 or ALARM 2 button three times.
The AL indicator is Yellow. This indicates the Wake To CD mode is selected and the alarm
is ‘On’.
Press the ALARM 1 or ALARM 2 button four times and the AL1 or AL2 indicators
disappear. This indicates that the alarms are canceled.
Wake To Buzzer
1. Check the wake-up time settings for Alarm 1, Alarm 2, or both alarms and adjust the wake up
times if necessary.
2. Press the ALARM 1 and/or ALARM 2 buttons once. The AL1 and/or AL2 indicators appear
Red.
3. At the selected wake up times the buzzer will turn on. It will continue for one hour and then
stop automatically and reset itself for the following day.
4. To stop the buzzer immediately, press the ALARM OFF/POWER button.
Wake To Radio
1. Check the wake-up time settings for Alarm 1, Alarm 2, or both alarms and adjust the wake up
times if necessary.
2. Turn the Radio ‘On’, tune to the desired station and set the VOLUME control to the desired
level to wake you up, then turn the radio ‘Off’ again.
3. Press the ALARM 1 and/or ALARM 2 buttons twice. The AL1 and/or AL2 indicators appear
Green.
4. At the selected wake up times the Radio will turn on. It will continue for one hour and then
stop automatically and reset itself for the following day.
5. To stop the Radio immediately, press the ALARM OFF/POWER button.
Wake To CD
1. Check the wake-up time settings for Alarm 1, Alarm 2, or both alarms and adjust the wake up
times if necessary.
2. Insert the desired CD in the CD player, start playback and adjust the VOLUME to the desired
level. Then press the STOP button to stop the disc and the ALARM OFF/POWER button to
shut the power ‘Off’.
3. Press the ALARM 1 and/or ALARM 2 buttons three times. The AL1 and/or AL2 indicators
appear Yellow.
4. At the selected wake up times the CD player will turn on. It will play for one hour, or until the
end of the disc, whichever comes first, and then stop automatically and reset itself for the
following day.
5. To stop the CD player immediately, press the ALARM OFF/POWER button.
NOTE: If there’s no CD inserted, or the CD is damaged, it will automatically change to Buzzer.
Canceling The Alarms
To cancel the alarms completely press the respective ALARM 1 and/or ALARM 2 buttons until
the AL1 and/or AL2 indicators disappear.
7
Snooze/Repeat Alarm
After the alarm turns on in the morning you can press the SNOOZE button for a few extra
minutes sleep. The alarm will stop for approximately 6 minutes and then come on again.
Snooze operation can be repeated several times if desired, but after one hour the alarm will not
turn ‘On’ again.
Sleep To Music Timer
You can use the sleep timer to fall asleep to the Radio or CD player for your desired time
(utmost 90 minutes) and have the unit shut off automatically.
y Press the ALARM OFF/POWER button to turn the power on. Operate the Radio or CD
player as usual. Adjust the volume to the desired level. The level you select for Sleep To
Music is the same level you will hear when the alarm turns “on” in the morning.
y Press and hold the SLEEP button to select the desired amount of sleep time from 90 minutes
to one minute. The SLEEP indicator comes ‘On’.
y When the display shows the desired amount of time, release the SLEEP button. After 5
seconds the display changes back to the correct time. The Radio or CD play will continue
until the sleep timer counts down to”00”and then shut off automatically.
y To stop the Radio or CD player before the sleep timer counts down to “00”, press the ALARM
OFF/POWER button to turn the unit “off”.
Notes:
If you set the sleep time for either 90 or 60 minutes and you are playing a CD that is only 48
minutes long, for example, playback will stop at the end of the disc.
Auxiliary Input Jack (connection cable not included)
This unit includes an AUX input jack to allow you to connect external devices, such as an
or portable MP3 player, and listen to the music stored on your external device through the
speakers of this radio.
Connect the headphone jack of your external device to the AUX input jack located on the front
panel of this unit. The connection cable is not included.
IMPORTANT:
When you connect a cable to the AUX input jack of this unit the ‘function’ selector automatically
switches from Radio or CD to Auxiliary Input. You must disconnect the cable from the AUX input
jack in order to listen to the Radio or CD again.
After connecting your external device to the AUX input jack, slowly adjust both the volume
controls on this unit and your external device to find the desired setting. Please note that if the
VOLUME control on this radio is set to a low level while the VOLUME control on your external
device is set too high, the sound will be distorted.
Remember to disconnect the connection cable after use in order to be able to listen to the Radio
or CD player again.
NOTE: If an external audio source is connected to the AUX (Auxiliary Input) jack at the wake-up
time the alarm will automatically default to the Buzzer mode, regardless of the mode you
selected.
Headphone (PHONES) Jack
This unit includes a 3.5mm PHONES (headphone) jack on the front panel. This allows you to
connect a set of stereo headphones (not included) for private listening without disturbing others.
When headphones are connected the built-in speakers are automatically disconnected.
8
IMPORTANT! When using stereo headphones always set the volume control to a low level
before you put on the headphones. Then put on the headphones and gradually adjust the
volume control to the desired level.
Remember that prolonged listening with headphones or ear buds at high volume
levels may eventually cause hearing loss.
Dimmer Control (optional)
The display DIMMER selector switch located on the right side cabinet was set to the HIGH
position at our factory.
If you find the display to be too bright for sleeping, slide the DIMMER selector switch to the
LOW position.
CARE AND MAINTENANCE
Compact Disc Care
To remove a disc from its storage case, press down on the center of the case and lift the disc
out, holding it carefully by the edges.
Fingerprints and dust should be carefully wiped off the disc’s recorded surface with a soft
cloth. Unlike conventional records, compact discs have no grooves to collect dust and
microscopic debris, so gently wiping with a soft cloth should remove most particles. Wipe in a
straight line from the inside to the outside of the disc. Small dust particles and light stains will
have absolutely no effect on reproduction quality.
Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents or abrasive
cleaners to clean the disc. If necessary, use a CD cleaning kit.
Never write on or affix labels to the surface of compact discs.
Care of the cabinet
If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax or polish
sprays on the cabinet.
It the front panel becomes dirty or smudged with fingerprints it may be cleaned with a soft
cloth slightly dampened with a mild soap and water solution. Never use abrasive cloths or
polishes as these will mar the finish of your unit.
Caution
Never allow any water or other liquids to get inside the unit while cleaning.
9
SPECIFICATIONS
CD SECTION
Channels:
Optical pick-up:
Frequency Response:
2 channels
3 beams laser
100Hz - 16K Hz
RADIO SECTION
Receiving Band:
Tuning Range:
AM/FM
AM 540 – 1600 KHz
FM
87.5 – 108 MHz
GENERAL
Output Power:
Phones jack:
Power Source:
Weight
Dimensions
Power Consumption:
Maximum 2 x 1.2 W
3.5mm
AC 230V ~ 50 Hz
DC 9V(006P)-FOR CLOCK BACKUP
Approx. 1.5 kg
Approx.210mm (L) x 215mm (W) x 105mm (H)
16W
ACCESSORIES
Instruction Booklet
Power Cord
1
1
Note: Specifications are subject to change for continuous improvement, therefore, we reserve
the right to those modifications without prior notice.
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising