BOXLIGHT XD-15c User`s Guide

BOXLIGHT XD-15c User`s Guide
BOXLIGHT XD-15c
User’s Guide
Copyright
Copyright © 2002 by BOXLIGHT Corporation. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system or
translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written permission of BOXLIGHT Corporation.
Disclaimer
BOXLIGHT Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Furthermore, BOXLIGHT
Corporation reserves the right to revise this publication and to make changes from time
to time in the contents hereof without obligation of BOXLIGHT Corporation to notify
any person of such revision or changes.
Fill this in!!
In case service is needed in the future, record the information described below. The
serial number is on the back of the product.
Projector Information
Product Name:
BOXLIGHT XD-15c Multimedia Digital Projector
Serial Number:
Date of Purchase:
Dealer Information
Dealer:
Telephone
Number:
Address:
BOXLIGHT XD-15c User’s Guide
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Shipping Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Projector Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
External Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Projector Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remote Control Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing or Replacing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting to Various Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Keystone Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Display Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. Source Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. PIP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
13
13
14
14
15
16
17
18
18
19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lamp Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use and Replacement of Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lamp Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting Lamp Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories (Included in the Standard Package). . . . . . . . . . . . . . . . . . . . . . .
20
20
20
20
22
23
23
Table of Contents iii
BOXLIGHT XD-15c User’s Guide
Optional Accessories (Not Included in the Standard Package) . . . . . . . . . 23
Ordering Parts or Getting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Status Messages
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Projector Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Timing Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
iv
Table of Contents
BOXLIGHT XD-15c User’s Guide
INTRODUCTION
Caution
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER –SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. PLEASE READ THIS USER’S GUIDE BEFORE YOU
OPERATE YOUR PROJECTOR. SAVE THIS USER’S GUIDE FOR
FUTURE REFERENCE .
Safety Instructions
1.
Read this user’s guide before you operate your projector and save it for future
reference.
2.
The lamp becomes extremely hot during operation. Allow the projector to cool
for approximately 45 minutes prior to removing the lamp assembly for
replacement. Do not operate lamps beyond the rated lamp life. Excessive
operation of lamps beyond the rated life could cause them to explode on rare
occasions.
3.
Never replace lamp assembly or any electronic components unless the projector
is unplugged.
4.
To reduce the risk of electric shock, do not disassemble this appliance. Take it to
a qualified technician when service or repair is required. Incorrect reassembly can
cause electric shock when the appliance is subsequently used.
5.
Do not place this product on an unstable cart, stand, or table. The product may
fall, sustaining serious damage.
6.
This product is capable of displaying inverted images for ceiling mount
installation. Please use suitable equipment for mounting the unit and ensure it is
securely installed.
•
Always open the lens shutter or remove the lens cap when the projector lamp is on.
Do not look straight at the projector lens during operation. The intense
light beam may damage your eyes.
In some countries, the line voltage is NOT stable. This projector is
designed to operate safely within a bandwidth of 110 to 240 volts, but
could fail if power cuts or surges of ±10 volts occur. In these high-risk
areas, it is recommended to install a power stabilizer unit to be used in
conjuction with this projector.
Caution
•
•
Save this user’s guide: The information contained in this manual will assist you in operating and maintaining your personal projector.
Introduction 1
BOXLIGHT XD-15c User’s Guide
Warranty
LIMITED WARRANTY
Boxlight ("Boxlight") warrants that each XD-15c ("the Product") sold hereunder will conform to and function in accordance with the written specifications of Boxlight. Said limited
warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. Said warranty shall
continue for a period of two (2) years from the date of such purchase. The standard limited
warranty excludes the lamps in projectors after 120 days and the accessories after one year.
Boxlight does not warrant that the Product will meet the specific requirements of the first
person or entity that purchases the Product for personal or business use. Boxlight's liability
for the breach of the foregoing limited warranty is limited to the repair or replacement of
the Product or refund of the purchase price of the Product, at Boxlight's sole option.
Replacement Product may be re-furbished in "like-new" condition, at Boxlight's sole discretion. To exercise the Purchaser's rights under the foregoing warranty, the Product must be
returned at the Purchaser's sole cost and expense, to Boxlight or to any authorized Boxlight
service center provided, and the Product must be accompanied by a written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the dealer's name; and
(iii) the model and serial number of the Product. When sending your unit in for repair,
please ship your unit in its original packing material or a Boxlight approved ATA Shipping
Case, or have a professional packaging company pack the unit. Please insure your shipment
for its full value. A return authorization number, issued by the Boxlight customer service
department, must also be clearly displayed on the outside of the shipping carton containing
the Product.
WARRANTY LIMITATION AND EXCLUSION
Boxlight shall have no further obligation under the foregoing limited warranty if the Product
has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical
stress (unusual physical and electrical stress includes unusually long operation, exposure to
smoke and other airborne contaminants), unauthorized modifications, tampering, alterations, or service other than by Boxlight or its authorized agents, causes other than from
ordinary use or failure to properly use the Product in the application for which said Product
is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS
PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES
THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY
SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY BOXLIGHT. SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT
APPLY TO YOU.
2
Introduction
BOXLIGHT XD-15c User’s Guide
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT'S LIABILITY WHETHER IN
CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE
PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL BOXLIGHT
BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE STATED FOR
THE PRODUCT IS A CONSIDERATION IN LIMITING BOXLIGHT'S LIABILITY. NO
ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE
YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
FCC Statement
FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual,
may cause interference to radio communications. It has been tested and found to comply
with the limits for a Class “A” computing device pursuant to Subpart B of Part 15 of the
FCC Rules, which are designed to provide reasonable protection against such interference
when operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference, in which case the user at his/her own expense will be
required to take whatever measures may be required to correct the interference.
FCC STATEMENT - CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the distance between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.
Introduction 3
BOXLIGHT XD-15c User’s Guide
Shipping Contents
The projector is shipped with the cables required for connection to standard PC or
laptop computers. Carefully unpack and verify that you have all the items shown below.
If any of these items are missing, please contact BOXLIGHT.
Optional Accessories
4
1.
Mac adapter (switchable)
2.
Spare lamp module
Introduction
BOXLIGHT XD-15c User’s Guide
Projector Description
Projector
1.
External control panel
(see next page)
9.
Video connector
Projection lens
10. D-sub connector
(for computer/ HDTV input)
3.
Front adjustment feet
11. Audio input
4.
IR remote sensor
12. Rear adjustment feet
5.
Ventilation grill
6.
Kensington lock
13. Lamp access door
(underneath unit)
7.
AC power cord input
8.
S-video connector
2.
12
5
Introduction 5
BOXLIGHT XD-15c User’s Guide
External Control Panel
Exit
Keystone/ Left
Keystone/ Right
Menu
Auto
Source
Power
Lamp status
indicator
•
•
•
•
•
•
•
•
6
The Infrared Remote Receiver (Front and Rear) allows the projector to
accept signals from the remote control. For best results, be sure to aim the control
toward the sensor without any obstructions between the two, and at a distance no
greater than 6 meters (20 feet).
Menu will display the menu system on screen. Press Menu again to access the
sub-menus. Left and Right help you navigate among choices and settings in the
menus and sub-menus. However, when the on screen menu is not activated, the
Left and Right buttons will function as Keystone +/- hot keys.
Press the Exit button to go back to the main menu. Press Exit again to leave the
menu system.
The Status Indicator will blink or light up when the lamp needs service, cooling
or replacement. See “Lamp Information” on page 20 for more detailed information.
When the projector is on, Back-lit Power will blink during warm-up and turn to
solid green to indicate the projector is ready for use.
Press and hold Power for 1 second to turn the projector on or off.
Auto key: Automatically sense the best picture quality for current received signals.
Source key: Select signal sources, PC, Video, S-video and YPbPr.
Introduction
BOXLIGHT XD-15c User’s Guide
Adjuster
The projector is equipped with a quick-release adjuster foot and button for adjusting
its tilt angle.
1.
Lift the projector up and press the adjuster button to release the adjuster.
2.
The adjuster will drop into position and be locked.
Projector Features
The projector integrates high performance optical engine projection and user-friendly
design to deliver high reliability and ease of use.
The Projector offers the following features:
•
Compact and portable unit
•
Full-function remote control
•
Manual zoom lens
•
One key auto-adjustment to display the best picture quality
•
Easy digital keystone correction through hot keys to correct distorted images
•
Adjustable color balance control for data/video
•
Ultra-high brightness projection lamp
•
Ability to display high quality 16.7 million colors
•
On screen menus in 7 languages: English, French, German, Italian, Spanish,
Simplified Chinese, and Traditional Chinese.
•
Powerful AV function to provide high AV picture
•
HDTV compatibility (YPBPR)
Note: The brightness of your machine will vary depending on the ambient
room conditions and contrast/brightness settings.
Introduction 7
BOXLIGHT XD-15c User’s Guide
Remote Control Description
(
Remote Control Features
The remote control sensors are located in the front/ back of the projector. The
distance between the sensor and the remote control should not exceed 6 meters (20
feet).
8
Introduction
BOXLIGHT XD-15c User’s Guide
FREEZE
The image can be frozen when FREEZE is pressed. A “Pause” icon will appear in the
lower right corner of the screen for three seconds. To release the freeze function,
press the FREEZE button, RETURN button or SOURCE button (when the input
source is switched over during display) again. A “Play” icon will appear in the lower
right corner of the screen for three seconds when the freeze function is released.
ZOOM IN/OUT
By pressing ZOOM IN +, the center of the picture will be magnified. When the +
button is pressed again, the picture is further magnified, up to four times the original
size. By pressing ZOOM OUT -, the size of the image is reduced. When the - button
is pressed again, the picture is further reduced until it is restored to its original size.
To return to the normal display mode, press the RETURN button. (This function can
be used in combination with FREEZE. )
Zoom In
A
A
Introduction 9
BOXLIGHT XD-15c User’s Guide
Installing or Replacing Batteries
•
•
Push and slide the battery compartment lid in the direction shown.
Install batteries as indicated by the diagram inside the compartment.
•
Position the lid over the compartment and snap it back into place.
Caution
Avoid excessive heat and humidity. There may be danger of an explosion if
batteries are incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
10
Introduction
BOXLIGHT XD-15c User’s Guide
INSTALLATION
Screen Size
Place the projector at the required distance from the screen according to the desired
picture size (see the table below).
L Projection Distance
Diagonal
(cm/in)
77/30.4
154/60.8
232/91.2
309/121.5
386/151.9
463/182.3
541/213.1
617/243.1
695/273.5
772/303.9
Screen Size (Max.)
A. Width
C. Height
(cm/in)
(cm/in)
61.8/24
46.3/18
123.65/49
92.7/36
185.3/73
138.9/55
247.0/97
185.2/73
308.7/122
231.6/91
370.5/146
277.9/109
432.2/170
324.18/128
494.0/194
370.5/146
555.7/219
416.7/164
617.5/243
463.11/182
L. Projection
distance (cm/in)
100/39
200/79
300/118
400/157
500/197
600/236
700/276
800/315
900/354
1000/394
Diagonal
(cm/in)
63/24.9
127/49.9
190/74.7
253/99.7
316/124.6
380/149.5
443/174.6
506/199.4
570/224.3
633/249.2
Screen Size (Min.)
B. Width
D. Height
(cm/in)
(cm/in)
50.7/20
38.0/15
101.3/40
76.0/30
151.9/60
113.9/45
202.5/80
151.9/60
253.2/100
189.9/75
303.8/120
227.9/90
354.4/140
266.2/105
405.1/160
303.8/120
455.7/180
341.8/135
506.3/200
379.8/150
Connecting to Various Equipment
It only takes a few seconds to connect your projector to your computer/notebook,
VCR or other systems. However, a Mac adapter (an optional accessory) is needed for
connection for Macintosh users.
Computer/
HDTV
S-Video/
Video
Audio
Video
S-Video
Installation 11
BOXLIGHT XD-15c User’s Guide
OPERATION
Start Up
1.
Plug the power cord into a wall socket.
2.
Press POWER for 1 second.
Remote Control
Projector
Power
Power
12
•
The back-lit POWER key blinks green and stays green when the power is turned
on.
(When the power is turned off, there is a 60-second cooling period before the
projector can be re-started.)
3.
Switch on all connected equipment.
Operation
BOXLIGHT XD-15c User’s Guide
Digital Keystone Correction
Keystoning refers to the situation where the projected image is noticeably wider at
either the top or bottom. To correct this, press KEYSTONE +/- (hot key) on the
control panel of the projector or on the remote control, then adjust the sliding bar
labeled Keystone, as needed. Press + to correct keystoning at the top of the image.
Press - to correct keystoning at the bottom of the image.
Projector
Auto
Source
Remote control
Auto Adjustment
In some cases, you may have to optimize the picture quality manually. To do this,
press the AUTO key on the control panel of the projector or on the remote control.
Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust to
the best picture quality.
Projector
Remote control
Auto
Auto
Source
Operation 13
BOXLIGHT XD-15c User’s Guide
Source Selection
When several input sources are available, press the SOURCE key to make a selection
from the control panel of the projector or the remote control.
Remote control
Projector
Power
Auto
Source
Source
Power
Menu System
Press Menu for the main menu and press 3or
again to select items in the sub-menu.
4 to select a sub-menu. Press Menu
Menu Bar
Sub-menu
PC
Display
Keystone
Brightness
Contrast
Phase
H.Size
Y/Pb/Pr
Video
14
Operation
Keystone
Brightness
Contrast
Color
Tint
Image
Auto resize
H-position
V-position
Color Temp
Information
Auto resize
H-position
V-position
Color
Tint
Color Temp
Ratio
System
Sharpness
Color Temp
Information
Source
Mirror
Source
Volume
Treble
Bass
Mute
Control
Langauge
OSD
OSD Time
Auto Off
Reset
Lamp hour
PIP
Main page:
PIP Source
PIP Size
PIP Pos.
H. Position
V.Position
More
Options
Sub Page:
Brightness
Contrast
Color
Tint
Sharpness
System
BOXLIGHT XD-15c User’s Guide
1. Display Menu
Corrects any keystoning of the image.
Keystone
Adjusts the brightness of the image.
Brightness
Adjusts the degree of difference between darkness and lightness of
the image.
Contrast
Adjusts to avoid the occurrence of flicker.
Phase
*This function is not available when the input modes are Video, SVideo.
Adjusts to fit in the desired image size.
H.Size
Color
Tint
*This function is not available when the input modes are Video, SVideo.
Increases or decreases the color range (R, G, B) of the image.
*This function is not available when the input mode is PC.
Adjusts the image to make it appear more red or blue.
*This function is not available when the input mode is PC.
Operation 15
BOXLIGHT XD-15c User’s Guide
2. Image Menu
Makes the best fit of the image to the screen,
Auto resize
Adjusts the horizontal position of the projected image.
H-position
Adjusts the vertical positon of the projected image.
V-position
Color Temp.
Adjusts the color temperature to fit your preference.
Information
Shows the current resolution.
Ratio
Users have 2 options for the image ratio.
1. 4:3 (Normal) 2. 16:9 (Wide)
*This function is not available when the input modes are PC, YPbPr.
System
4 modes can be selected.
1. Auto 2. PAL-M 3. PAL-N 4.SECAM
*The default setting of System is Auto.
*This function is not available when the input modes are PC, YPbPr.
Sharpness
Color
Tint
16
Operation
Adjusts the image to make it look sharper or softer.
*This function is not available when the input modes are PC, YPbPr.
Increases or decreases the color range (R, G, B) of the image.
*This function is not available when the input mode is PC.
Adjusts the image to make it appear more red or blue.
*This function is not available when the input mode is PC.
BOXLIGHT XD-15c User’s Guide
3. Source Menu
2.
1.
Mirror
1.
Default
2.
Ceiling mounted
projection
3.
Rear screen
projection
4.
Ceiling mounted and
rear screen
projection
Source
4.
3.
Selects sources between PC, Video, S-Video, and YPbPr.
Adjusts the volume level.
Volume
Adjusts the treble level.
Treble
Adjusts the bass level.
Bass
Off
On
Mute
Operation 17
BOXLIGHT XD-15c User’s Guide
4. Control Menu
Language
OSD
OSD Time
Auto Off
Reset
Lamp Hour
Language sets the OSD to display in one of 7 languages.
Use 3 / 4 key to select the languages: English, French, German, Italian, Spanish, Simplified Chinese and Traditional Chinese.
Selects a desired OSD position.
Sets the length of time the OSD will remain active after the last
time you pressed the button. The range is from 5 to 60 seconds in 5-second increments.
Sets the length of time to shut off the system when no input is
detected.
Returns all settings to the time of manufacturing.
Shows lamp usage time.
5. PIP Menu
These functions are valid only when the input mode is PC and the PIP source is Video or
S-Video.
PIP Source
PIP Size
PIP Position
Uses 3 / 4 key to scroll through the 4 alternatives: Off,
Small, Medium, Large.
Selects a desired position for the PIP.
H Position
Adjusts the horizontal position of the PIP image.
V Position
Adjusts the vertical position of the PIP image.
More Options
Brightness
Contrast
Color
18
Selects the source for the PIP.
Uses 3 / 4 key to select more PIP functions including Brightness, Contrast, Color, Tint, Sharpness and System.
Adjusts the brightness of the PIP image.
Adjusts the degree of difference between dark and light for the
PIP image.
Increases or decreases the color range (R, G, B) of the image.
Tint
Adjusts the image to make it appear more red or blue.
Sharpness
Adjusts the image to make it appear sharper or softer
System
Selects PIP image systems: Auto, NTSC, PAL, SECAM
Operation
BOXLIGHT XD-15c User’s Guide
Shutdown
1.
Press POWER and a warning message will prompt up. To turn off the projector,
Press POWER again.
2.
The fan will continue to run for approximately 60 seconds.
Power
Power
3.
Disconnect the power cord from the wall socket.
Caution
Please do not unplug the power cord before POWER is shut down or during the 60-second cooling process.
If the projector is not properly shut down, to protect the lamp, the system
will detect this and cool the lamp for two minutes automatically before
turning on again.
Operation 19
BOXLIGHT XD-15c User’s Guide
MAINTENANCE
Lamp Information
Use and Replacement of Lamp
When the Lamp Indicator lights up red or a message appears suggesting the time of lamp
replacement, please install a new lamp or consult your dealer. An old lamp could cause a
malfunction in the projector and in rare instances may even explode.
LED Status Indicators
Lamp Life Indicators
CHANGE THE LAMP, AND
RESET THE LAMP TIMER
CHANGE THE LAMP. THE
POWER WILL TURN OFF
AFTER 20 HOURS
CHANGE THE LAMP!
When this LED shows red continuously, it is warning you that
the lamp usage has exceeded 1500 hours. Replace the projection lamp with a new one immediately.
The lamp has been in operation for 1400 hours. Change a
new lamp for optimal performance.
The lamp has been in operation for 1480 hours, and the
power will turn off after 20 hours.
The lamp has been in operation for over 1500 hours. The
warning message will display for 30 seconds every 5 minutes
after you turn on the projector and the power will turn off
automatically in 10 minutes.
Lamp is not properly attached LED blinks rapidly.
Temperature is too high
When the projector’s internal temperature is too high to
operate safely, the LED blinks slowly for one minute and the
lamp turns off automatically.
If the LED light is off, the projector’s lamp and temperature
are operating under normal conditions.
Caution
The LAMP indicator will light up if the lamp becomes too hot. Turn off the
power and let the projector cool for 45 minutes. If the LAMP indicator is still
red when turning the power on, please contact BOXLIGHT Technical Support at 1-800-762-5757 or +1-360-779-7901.
Lamp Replacement
Caution
To reduce the risk of electrical shock, always turn off the projector and disconnect the power cord before changing the lamp.
20
Maintenance
BOXLIGHT XD-15c User’s Guide
1.
Press the POWER button to switch off the projector. Disconnect the power
cord from the outlet and the projector.
2.
Loosen the screw and remove the lamp cover. If the lamp is hot, avoid burns by
waiting 45 minutes until the lamp has cooled.
3.
Loosen the 3 screws. (It is strongly recommended you use a magnetic-headed
screwdriver.) Pull the handle to remove the lamp housing. If the screws are not
loosened completely, they could injure your fingers. Do not insert your hand into
the box after the lamp is removed. If you touch the optical parts inside, this could
cause color unevenness.
4.
Replace the lamp with a new one. Insert it into the projector, and tighten the
screws firmly. Loose screws may cause a bad connection, which may result in
malfunction.
5.
Re-install the lamp cover and tighten the screw. Do not turn on the power
with the lamp cover removed. Whenever the lamp is replaced, reset the
total lamp operation time. Do not reset if the lamp is not replaced as this
could cause breakage.
Maintenance 21
BOXLIGHT XD-15c User’s Guide
Caution
To reduce the risk of severe burns, allow the projector to cool for at least 45
minutes before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components,
use caution when removing lamp glass that has shattered into sharp pieces.
Please call BOXLIGHT Technial Support if your lamp has exploded.
To reduce the risk of injuries to fingers and/or decreasing image quality by
touching the lens, do not touch the empty lamp compartment when the
lamp is removed.
This lamp contains mercury. Consult your local hazardous waste regulations
to dispose of this lamp in a proper manner.
Resetting Lamp Hours
If you replace the lamp after 1500 hours of operation, please follow the instructions
below within 10 minutes of power on.
OSD
FUNCTION
Press the Exit button on the projector for 3
seconds to display the total used lamp time.
•
•
22
Maintenance
Press the MENU button on the projector
during the lamp hour message. An
adjustment message will appear.
Press W or X to rest lamp hours or press
EXIT to leave.
BOXLIGHT XD-15c User’s Guide
Service Information
Accessories (Included in the Standard Package)
Power cord (EU)
Power cord (US)
Power cord (UK)
VGA signal cable
Video cable
S-Video cable
Audio cable
Audio - PC audio cable
Soft carrying case
Lens cover
Remote control
3-2 converter
Optional Accessories (Not Included in the Standard Package)
Mac adapter (switchable)
Spare lamp module
Ordering Parts or Getting Information
For product information, product assistance, service information, or to order
accessories, please contact BOXLIGHT Corporation at 1-800-762-5757 or +1-360779-7901 or visit the web site at www.boxlight.com.
Maintenance 23
BOXLIGHT XD-15c User’s Guide
TROUBLESHOOTING
Common Problems & Solutions
PROBLEMS
NO POWER
NO PICTURE
TRAPEZOID
IMAGE ON
THE SCREEN
POOR COLOR
BLURRED
IMAGE
REMOTE
CONTROL
DOES NOT
WORK
24
Troubleshooting
TRY THESE SOLUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Plug the power cord into the AC inlet.
Plug the power cord into the power inlet.
Wait two minutes after the projector is turned off before turning
the projector back on.
Check for the proper input source.
Ensure all cables are connected properly.
Adjust the brightness and contrast.
Remove the lens cap.
Reposition the unit to improve its angle on the screen.
Use the Keystone correction key on the control panel of the
projector or the remote control unit.
Select the correct video system.
Adjust brightness, contrast, or saturation.
Press Auto on the control panel of the projector or the remote
control unit to get better picture quality.
Adjust the focus.
Reposition the unit to improve its projection angle.
Ensure the distance between the unit and screen is within the
adjustment range of the lens.
Replace the batteries with new ones.
Make sure there is no obstacle between the remote control and
the projector.
Stand within 6 meters (20 feet) of the unit.
Make sure nothing is blocking the front and rear receivers.
BOXLIGHT XD-15c User’s Guide
Status Messages
On Screen Messages
SEARCHING
INPUT SIGNAL
DETECTED,
ACTIVATING AUTO
IMAGE
SYNC IS OUT OF
RANGE
Description
Projector is searching for input.
Projector has identified the input signal and is running the auto
image adjustment function.
Input signal frequency exceeds the projector’s range.
CHANGE THE LAMP,
AND RESET THE LAMP
TIMER
The lamp has been in operation for 1400 hours. Lamp replacement is recommended.
CHANGE THE LAMP,
THE POWER WILL
TURN OFF AFTER 20
HOURS
The lamp has been in operation for 1480 hours, and the power
will turn off after 20 more hours. Replace the lamp as soon as
possible.
CHANGE THE LAMP!
The lamp has been in operation for over 1500 hours, and the
power will turn off automatically in 10 minutes. Replace the
lamp immediately.
Troubleshooting 25
BOXLIGHT XD-15c User’s Guide
SPECIFICATIONS
Projector Specifications
Technical Specifications
Note: All specifications are subject to change without notice.
General
Product name
Model name
Optical
Display system
Lens F/Number
Lamp
Personal Projector
BOXLIGHT XD-15c
1024X768 XGA
1-CHIP DMD
F/2.6
120W VIP lamp
Electrical
Power supply
Power consumption
Mechanical
Dimensions
Operating Temperature
range
Weight
Input terminal
Computer Input
RGB/ HDTV Input
Video Signal Input
S VIDEO
VIDEO
Audio Signal Input
Audio
AC100 ~ 240V, 2.3A, 50/60 Hz (Automatic)
185 W (Max)
220mm/8.7in(W) x 52mm/2.1in(H) x 175mm/6.9in(D)
10°C ~ 40°C
3.85 lbs (1.69 Kg)
D-sub 15-pin (female)
Mini DIN 4-pin terminal
RCA Jack terminal
Mini Jack Stero Terminal
Output
Speaker
26
Specifications
1 Watt x 1
BOXLIGHT XD-15c User’s Guide
Timing Chart
Resolution
H Sync (kHz)
V Sync (Hz)
640x350
31.5
70.1
Remark
640x400
37.9
85.1
720x400
31.5
70.0
VESA
720x400
37.9
85.1
VESA
640x480
31.5
60.0
VESA
640x480
37.9
72.8
VESA
640x480
35.0
66.7
Macintosh
640x480
43.3
85.0
VESA
800x600
35.2
56.3
VESA
800x600
37.9
60.3
VESA
800x600
46.9
75.0
VESA
800x600
48.1
72.2
VESA
800x600
53.7
85.1
VESA
832x624
49.7
74.5
Macintosh
1024x768
48.4
60.0
VESA
1024x768
56.5
70.1
VESA
1024x768
60.0
75.0
VESA
1024x768
68.7
85.0
VESA
1280x1024
64.0
60.0
VESA
Specifications 27
BOXLIGHT XD-15c User’s Guide
DIMENSIONS
220mm
175 mm
52mm
28
Dimensions
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising