HT-S5300 - Sears Parts Direct
ON
YOo
Contents
7.1ch Home Theater System
HT-S5300
AV Receiver (HT-R580)
Speaker Package (HTP-580)
Front Speakers
(SKF-580
L/R)
Center Speaker (SKC-580)
Surround
Speakers
(SKR-580
L/R)
Surround
Back Speakers
(SKB-580
Subwoofer
(SKW-580)
Universal
(UP-A1)
Port Option
Instruction
L/R)
Dock for iPod ®
Manual
Thank you for purchasing an Onkyo 7. Ich Home
Theater System. Please read this manual thoroughly
before making connections and plugging in the unit.
Following the instructions
in this manual will enable
you to obtain optimum performance
and listening
enjoyment from your new 7. l ch Home Theater
System.
Please retain this manual for future reference.
Advanced Operations :,,,,,,,,,,,,,,,:33
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
CAUTION:
5
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE
PARTS INSIDE. REFER
SERVICING
TO
QUALIFIED
SERVICE
PERSONNEL.
The lightning
magnitude
persons.
1.
2.
3.
4.
to constitute
The exclamation
symbol,
within an
a risk
of electric
point within an equilateral
shock
to
triangle
is
intended to alert the user to the presence of important
operating and maintenance
(servicing)
instructions in
the literature
Important
flash with arrowhead
equilateral triangle, is intended to alert the user to the
presence of uninsulated
"dangerous
voltage" within
the product's
enclosure
that may be of sufficient
accompanying
the appliance.
Safety Instructions
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
5. Do not use this apparatus near water.
A. When the power-supply cord or plug is damaged,
6. Clean only with dry cloth.
B. If liquid has been spilled, or objects have fallen
7. Do not block any ventilation openings. Install in
into the apparatus,
accordance with the manufacturer's instructions.
C. If the apparatus has been exposed to rain or water,
8°
Do not install near any heat sources such as radiators,
D. If the apparatus does not operate normally by folheat registers, stoves, or other apparatus (including
lowing the operating instructions. Adjust only
amplifiers) that produce heat.
those controls that are covered by the operating
9°
Do not defeat the safety purpose of the polarized or
instructions as an improper adjustment of other
grounding-type plug. A polarized plug has two blades
controls may result in damage and will often
with one wider than the other. A grounding type plug
require extensive work by a qualified technician to
has two blades and a third grounding prong. The wide
restore the apparatus to its normal operation,
blade or the third prong are provided for your safety. If
E. If the apparatus has been dropped or damaged in
the provided plug does not fit into your outlet, consult
any way, and
an electrician for replacement of the obsolete outlet.
F. When the apparatus exhibits a distinct change in
10. Protect the power cord from being walked on or
performance this indicates a need for service.
pinched particularly at plugs, convenience receptacles,
16. Object and Liquid Entry
and the point where they exit from the apparatus.
Never push objects of any kind into the apparatus
11. Only use attachments/accessories
specified by the
through openings as they may touch dangerous voltmanufacturer.
age points or short-out parts that could result in a fire
12. Use only with the cart, stand,
or electric shock.
PORTABLE
CART
WARNING
tripod, bracket, or table speciThe apparatus shall not be exposed to dripping or
fied by the manufacturer, or
splashing and no objects filled with liquids, such as
sold with the apparatus. When
vases shall be placed on the apparatus.
a cart is used, use caution
Don't put candles or other burning objects on top of
this unit.
when moving the cart/apparatus combination to avoid
17. Batteries
injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Ser-
vicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has
been dropped.
En
2
Always consider the environmental issues and follow
local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is adequate ventilation.
Leave 20 cm (8") of free space at the top and sides and
10 cm (4") at the rear. The rear edge of the shelf or
board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a flue-like
gap for warm air to escape.
Precautions
1.
2.
3.
4.
Recording Copyright--Unless
it's for personal use
only, recording copyrighted material is illegal without
the permission of the copyright holder.
AC Fuse--The AC fuse inside the unit is not user-serviceable. If you cannot turn on the unit, contact your
Onkyo dealer.
Care--Occasionally
you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don't use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the voltage requirements printed on the unit's rear panel (e.g.,
AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug is
readily operable (easily accessible) at all times.
Pressing ON/STAN DBY to select Standby mode does
not tully shutdown the unit. If you do not intend to use
the unit for an extended period, remove the power cord
from the AC outlet.
5,
6,
7,
8°
Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and headphones can cause hearing loss.
Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat as sunshine, fire or the
like.
Never Touch this Unit with Wet Hands--Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside
this unit, have it checked by your Onkyo dealer.
Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
• Do not leave rubber or plastic items on this unit for
a long time, because they may leave marks on the
case.
• This unit's top and rear panels may get warm alter
prolonged use. This is normal.
• If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be
sure to use it occasionally.
For
U.S. models
FCC Information
for User
CAUTION:
The user changes
or modifications
by the party responsible
user's authority
not expressly
for compliance
approved
could void the
to operate the equipment.
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For Canadian
Models
NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION:
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
ModUle
pour
les Canadien
REMARQUE:
CET APPAREIL NUMt_RIQUE DE
LA CLASSE B EST CONFORME A. LA NORME NMB003 DU CANADA.
Sur les modbles dont la fiche est polaris_e:
ATTENTION:
POUR t_VITER LES CHOCS t_LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE
DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU
FOND.
EF1
3
Speaker Precautions
Package Contents
Placement
Make sure you have the following items:
• The subwoofer cabinet is made out of wood and is therefore sensitive to extreme temperatures and humidity, do
not put it in locations subject to direct sunlight or in
humid places, such as near an air conditioner, humidifier,
bathroom, or kitchen.
5
• Do not put water or other liquids close to the speakers. If
liquid is spilled over the speakers, the drive units may be
damaged.
• Speakers should only be placed on sturdy, fiat surfaces
that are free from vibration. Putting them on uneven or
unstable surfaces, where they may fall and cause damage, will affect the sound quality.
• Subwoofer is designed to be used in the upright vertical
position only. Do not use it in the horizontal or tilted
position.
• If the unit is used near a turntable, CD player or Blu-ray
Disc/DVD player, howling or slipping of sound may
occur. To prevent this, move the unit away from the turntable, CD player or Blu-ray Disc/DVD player, otherwise
lower the unit's output level.
Using Close to a TV or Computer
TVs and computer monitors are magnetically sensitive
devices and as such are likely to suffer discoloration or
picture distortion when conventional speakers are placed
nearby. To prevent this, the SKF-580 and SKC-580 feature
internal magnetic shielding. In such situations, try moving
the speakers away from your TV or monitor. If discoloration should occur, turn off your TV or monitor, wait 15 to
30 minutes, and then turn it back on again. This normally
activates the degaussing function, which neutralizes the
magnetic field, thereby removing any discoloration
effects. Note that discoloration can also be caused by a
magnet or demagnetizing tool that's too close to your TV
or monitor.
Do not place SKR-580 and SKB-580 close to TV or a
computer monitor because they have no magnetic shield.
Input Signal Warning
The speakers can handle the specified input power when
used for normal music reproduction. If any of the following signals are ted to them, even if the input power is
within the specified rating, excessive current may flow in
the speaker coils, causing burning or wire breakage:
1. Interstation noise from an untuned FM radio.
2.
3.
Sound from fast-forwarding a cassette tape.
High-pitched sounds generated by an oscillator, electronic musical instrument, and so on.
4.
5.
6.
Amplifier oscillation.
Special test tones from audio test CDs and so on.
Thumps and clicks caused by connecting or disconnecting audio cables (always turn off your amplifier
before connecting or disconnecting cables).
Microphone feedback.
7.
En
4
P_I_I ......
:Id
HT-R580 (_ 7)
Remote controller and two batteries (AA/R6) (_ 5)
Indoor FM antenna (_ 19)
AM loop antenna (_ 19)
In catalogs
uct name
and on packaging,
indicates
the same regardless
the color.
the letter at the end of the prodSpecifications
and operations
of color.
Front speakers (SKF-580 L/R) (_ 9)
Center speaker (SKC-580)
(_ 9)
Surround
speakers (SKR-580 L/R) (_ 9)
Surround
back speakers (SKB-580 L/R) (_ 9)
Subwoofer
(SKW-580)
(_ 9)
Speaker cables for front speakers 11 ft. (3.5 m)
(White and Red)(_ 13)
Speaker cable for center speaker 10 ft. (3.0 m)
(Green) (_ 13)
Speaker cables for surround speakers 26 ft. (8.0 m)
(Blue and Gray) (_ 13)
Speaker cables for surround back speakers 26 ft.
(8.0 m) (Brown and Tan) (_ 13)
RCA cable for subwoofer
(_ 13)
connection
10 ft. (3.0 m)
4 rubber spacers for center speaker (_ 14)
4 floor pads for the subwoofer (_ 14)
UP-A1 (_ 47)
Easily links iPod/iPhone u]odels with Onkyo A/V Systeu]s
are
Contents
Installing the Batteries
Introduction
Important Safety Instructions .........................................
Precautions .......................................................................
• ff the remote controller
..........
doesn't work reliably, try
replacing the batteries.
• Don't mix new' and old
batteries or different
types of batteries.
• ff you intend not to use
the remote controller for
2
3
Batteries
(AA/R6)
a long time, remove the batteries to prevent damage from leakage or corrosion.
• Remove expired batteries as soon as possible to prevent damage
iYom leakage or corrosion.
Speaker Precautions ........................................................
Package Contents ............................................................
Features ............................................................................
Front & Rear Panels .........................................................
4
4
6
7
Speaker Package ..............................................................
Remote Controller ..........................................................
About Home Theater ......................................................
9
10
11
Connecting
12
the AV Receiver .........................................
_
Remote control sensor
Turning On/Off the AV Receiver ...................................
Basic Operations ............................................................
Listening to the Radio ....................................................
Recording ........................................................................
Using the Listening Modes ............................................
21
22
24
27
28
Advanced Setup .............................................................
Zone 2 ..............................................................................
33
44
Controlling iPod .............................................................
Controlling Other Components .....................................
47
51
Troubleshooting .............................................................
Specifications .................................................................
About HDMI .....................................................................
54
58
60
AV receiver
• (5 m)
Using an RIHD-compatible
TV, Player, or Recorder ...61
on and, while holding down VCR/DVR, press
I To
reset the AV receiver
ON/STANDBY
(_ 54). to its factory defaults,
ii
71!1!11
Aiming the Remote Controller
To use the remote controller, point it at the AV receiver's
remote control sensor, as shown below.
iiI
turn it
Erl
5
Features
AV Receiver HT-R580
5
*4 ibli211rlrl|o
• 130 Watts/Channel
@ 6 ohms
• 160 Watts/Channel
@ 6 ohms (JEITA)
• WRAT-Wide
Range
Amplifier
Technology
(5 Hz to 100 kHz bandwidth)
• Optimum
Gain Volume
• H.C.RS. (High Current
Power Transformer
• HDMI
Circuitry
Power
DTS-HD
Dolby
Return
Lip Sync,
High Resolution
Digital
Channel,
DTST-HD
• Non-Scaling
Audio,
Dolby TrueHD*2,
Mode
and Highly
• 4 HDMF4
Inputs
Inputs
Accurate
Digital
(20ptical/2
(North
(2 Inputs/l
American
Zone
• 40 FM/AM
*
EQ*6 for Loudness
• Audyssey
Dynamic
Volume*6
and Dynamic
Room
Acoustic
En
6
and regulatory
is a trademark
accessory
has
and has been
performance
for the operation
"x.v.Color"
has been
standards.
to iPhone
to meet Apple
with safety
L/R 2-Way
• Max. input power:
Correction
to Maintain
Optimal
Lis-
• 6-ohm
stan-
of this device
standards.
of Sony Corporation.
Front
Speakers
Hz)
(up to 100 ms)
• 3-1/4"
130 W
shielded
speaker
2-Way
terminals
Center
Remote
• Max. input power:
• 6-ohm
• Color-coded
DOLBY
llz ]
Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories.
"3 Music Optimizer TM is a trademark of Onkyo Corporation.
SKR-580
SKB-580
• 3-1/4"
cable
dome tweeter
130 W
shielded
impedance
speaker
terminals
and speaker
cable
L/R Full-Range
Surround
Speakers
L/R Full-Range
Surround
Back
Speakers
(8 cm) cone
• Max. input power:
• 6-ohm
and speaker
Speaker
(8 cm) cone woofer
• 1" (2.5 cm) Balanced
via HDMI
R I-Compatible
SKC-580
dome tweeter
impedance
• Color-coded
Adjustment
Function
• Magnetically
Master Audio
LOGIC
performance
that an electronic
specifically
is not responsible
Manufactured under license under U.S. Patent #'s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535;
7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS is a registered
trademark and the DTS logos, Symbol, DTS-HD and DTSHD Master Audio are trademarks of DTS, Inc.
©1996-2008 DTS, Inc. All Rights Reserved.
PRO
to connect
by the developer
• Magnetically
[_
means
• 1" (2.5 cm) Balanced
Problems
Range
(40/50/60/80/100/120/150/200
•2
to meet Apple
iPhone"
accessory
to iPod and has been certified
• 5" (12 cm) OMF cone woofer
Presets
• Preprogrammed
specifically
compliance
SKF-580
Display
with
[nc.
that an electronic
tuner
2
• A/V Sync Control
to connect
by the developer
of Apple
means
in the U.S. and
Posts
Dynamic
• On-Screen
designed
[nc., registered
Speaker Package HTP-580
Speaker
• Audyssey
• Crossover
Radio
models)/DAB+
EQ*6 to Correct
Level
for iPod"
Apple
audio player
• Audyssey
tening
Output)
models)
Plug-Compatible
is a trademark
"Made
certified
dards.
Coaxial)
of Apple
iPhone
been designed
Port for the Dock for iPod*/HD
• Powered
DSP
Control
in" Input for Portable
(Asian
files
"Works
• Front "Line
tuner module
Music
32-bit Processing
Video Switching
module
VOLUME
iPod is a trademark
other countries.
and 1 Output
• Component
• Banana
Direction
Memory
1-411-11D for System
• Universal
EQ
DYNAMBC
Manufactured under license from Audyssey Laboratories TM.
U.S. and foreign patents pending.
Audyssey EQ TM, Audyssey Dynamic Volume TM and
Audyssey Dynamic EQ TM are trademarks of Audyssey Laboratories.
PCM
High"
• Music Optimizer*3 for Compressed
• 192 kHz/24-bit
D/A Converters
• 4 Digital
Audio,
Configuration
• A-Form Listening
• Direct Mode
• Onkyo
High
3D), Deep-
Master
Plus, DSD and Multi-CH
• Dolby Pro Logic IIz*2 (with "Front
Mode)
• Powerful
Massive
*6
(Ver. 1.4 with Audio
Color, x.v.Color*,
Supply)
"HDM[, the HDM[ Logo, and High-Definition Multimedia
[nterface are trademarks or registered trademarks of HDM[
Licensing LLC in the United States and other countries."
*5 The HD Radio Ready logo is a proprietary trademark of iBiquity Digital Corp.
To receive HD Radio broadcasts, you must install an Onkyo
UP-HTI HD Radio tuner module (sold separately).
130 W
impedance
• Color-coded
speaker terminals
SKW-580
Bass Reflex Powered
and speaker
Subwoofer
• 10" (25 cm) cone woofer
• Max. power:
290 W (Dynamic
power)
cable
or its
Front & Rear Panels
r=_,_Imr_g_r4j
North
American
models
i
Asian
models
ONKYO
{
The actual front panel has various logos printed on it. They are not shown here for clarity.
The page numbers in parentheses show where you can find the main explanation for each item.
(_ ON/STANDBY button (_ 21)
(_ SETUP button (_ 33)
(_ STANDBY indicator (_ 21)
O TUNING, PRESET (_ 24 to 25), arrow and
ENTER buttons
(_ HDMI THRU indicator (_ 40)
@ ZONE 2 indicator (_ 45)
(_ RETURN button
(_
Remote control sensor (_ 5)
O
ZONE 2, OFF, ZONE 2 LEVEL/TONE LEVEL
and TONE buttons (_ 43, 45 to 46)
(D MUSIC OPTIMIZER button (_ 22, 42)
MASTER VOLUME control (_ 22)
(_ PHONES jack (_ 23)
Input selector buttons (_ 22)
(_
Display (_ 8)
(_
LISTENING MODE buttons (_ 28)
(_
DIMMER button (North American
O
MEMORY button (_ 25)
AUX INPUT AUDIO jacks (_ 18)
(_
TUNING MODE button (_ 24)
RT/PTY/TP button (Asian models) (_ 26)
(_
DISPLAY button (_ 22)
models) (_ 22)
@ AUX INPUT LINE IN jack (_ 18)
AUX INPUT VIDEO jack (_ 18)
Eft
7
ii
For detailed
@
Audio
information,
input
see the pages
(_) RDS indicator
(_) Listening
mode and format
(_) Audyssey
indicators
(_) Tuning
in parentheses.
indicators
indicators
indicators
(@ 22, 28)
(@ 37)
(@ 24)
(_) SLEEP
North
area
(_) HDMI IN and OUT jacks
O
@ FM ANTENNA jack and AM ANTENNA terminal
Composite
video and analog audio jacks
(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN,
GAME IN, TV/CD IN)
MONITOR OUT V jack
(_ ZONE 2 LINE OUT jacks
UNIVERSAL
(_ SUBWOOFER
SPEAKERS
PORT jack
terminals
(CENTER, FRONT, SURR, SURR BACK OR
FRONT HIGH)
Power cord
models)
(@ 23)
(_) 1-41REMOTE CONTROL jack
VIDEO IN and OUT jacks
American
(@ 23)
indicator
(_) DIGITAL IN COAXIAL and OPTiCAL jacks
(_) COMPONENT
8
indicator
(Z) MUTING
(_) Message
En
(excluding
(@ 25)
PRE OUT jack
FRONT HIGH OR ZONE 2 SPEAKERS terminals
See "Connecting the AV Receiver" for connection information (@ 12 to 20).
Speaker Package
For detailed information, see the pages in parentheses.
m Front
N Rear
(North American
models)
ToAC_
i
_
@ STANDBY/ON indicator
Red:
Blue:
Subwoofer in standby mode
Subwoofer on
(Asian models)
With the Auto Standby function, the SKW-580 automatically turns on when an input signal is detected in
Standby mode. When there's no input signal for a
while, the SKW-580 automatically enters Standby
mode.
(_) OUTPUT LEVEL control (_ 21, 22)
This control is used to adjust the volume of the subwoofer.
@ LINE INPUT (_ 13)
• The Auto
This RCA input should be connected to the subwoofer
pre out on the AV receiver with supplied RCA cable.
does
@
Keyhole
turns
the subwoofer
level. [f the Auto
try slightly
increasing
level on the AV receiver
Front
on when
Standby
the
function
or decreasing
the
(@ 36).
Near
SKC-580
slots can be used to wall-mount
speaker.
See "Wall Mounting"
tions (_
14).
for mounting
the
instruc-
terminals
These push terminals are for connecting
the speaker
the HT-R580
with the supplied
cables.
The supplied
speaker
identification.
Simply
colored
output
slots
These keyhole
(_) Speaker
a certain
SKR-580/SKB-580
Rear
Front
function
not work reliably,
subwoofer
SKF-580
Standby
input signal exceeds
positive
cables
connect
speaker
speaker
are color-coded
to
Front
Rear
for easy
each cable to the same-
terminal.
] [0RII1R'a_
• The front grilles are not designed to be removed so do
not attempt to remove them forcibly, as this will damage
them.
En
9
/
Remote Controller
r_j__
For detailed information, see the pages in parentheses.
@ ON/STANDBY
button (@ 21)
(_) REMOTE MODE/INPUT SELECTOR buttons
(@ 22)
(_) SP LAYOUT button (@ 23)
@ Arrow i,/¥/_1/_
(_
and ENTER buttons
SETUP button (_ 33)
@ LISTENING MODE buttons (@ 28)
(Z) DIMMER button (@ 22)
(_) DISPLAY button (_ 22)
(_
MUTING button (@ 23)
@ VOL A/_r button (@ 22)
_)
RETURN button
AUDIO button (@ 41)
SLEEP button (@ 23)
i.............................. LISTENING
..............................
.................
........
.......
® ® ®
©®®
\%y
®
0
MODE
\y
_
@
,___o
=_M_M_
E___
..........
SLEEP
m Controlling the tuner
To control the AV receiver's tuner, press TUNER (or
RECEIVER).
You can select AM or FM by' pressing TUNER repeatedly.
0
D.TUN button (@ 24)
O
See "Entering Remote Control Codes" for more details
(@51).
*2 VIDEO is not used for this model.
En
10
DISPLAY button
Ell CH +/- button (@ 25)
0
"1 To control componenL you must first enter remote control
code.
Arrow A/¥ buttons (@ 24)
Number buttons (@ 24)
About Home Theater
Thanks
to the AV receiver's
own home--just
With
superb
capabilities,
like being in a movie
analog or digital
you can enjoy
theater or concert
TV, you can enjoy Dolby
surround
speakers
These
output
listener
This
at about
sound.
speaker
tile front
about
2 to 3 feet
These
back
improve
sound
They
them
speakers
enhance
playing
cm) above
experiment
positions
provides
by placing
within
the most
music
your
the room,
satisfying
with good
subwoofer
and choose
disfor dia-
at about ear level, or at the
positioning
and to add realistic
or slightly
behind,
they should
be
Digital
the realism
EX, DTS-ES
of surround
the listener.
Position
Matrix,
sound
them
and
behind
the
ear level.
to enjoy Dolby
the spatial
the front
Pro Logic
experience.
speakers
them
etc.
at least
(and as high as possible).
to left and right place
Ideally
IIz Height,
Position
they should
at an angle
be positioned
slightly
directly
wider
above
speakers.
(SKW-580)
handles
channel.
tile bass sounds
The volume
will depend
and your listening
for your subwoofer,
mainly
(Optional)
significantly
Tile subwoofer
subwoofer
a movie or some
enhance
behind
it is acceptable
@ Subwoofer
Effects)
movements
(SKB-580)
are necessary
than the front speakers.
the front
sound
it's used
of the listener,
to enjoy Dolby
etc. They
speakers
3.3 feet (100
• To find the best position
forward
sound
at the sides
localization
speakers
Although
position
making
In movies
about 2 to 3 feet (60 to 100 cm) above
high
inward
(SKR-580)
are necessary
Discrete,
These
them
i__ iiii _i i
the
the listener.
DTS-ES
@ Front
facing
at the apex.
(60 to 100 cm) above ear level. Ideally
from
speakers
listener
1/3 of wall
image.
are used for precise
Position
@ Surround
is to provide
speakers.
speakers
equidistant
theater
be positioned
from the TV. Angle
speakers,
a full sound
it close to your TV facing
speakers
Digital.
modes.
(SKC-580)
as the front
ambience.
should
the listener
same height
These
DSP listening
role ill a home
They
log. Position
@ Surround
position
Their
image.
with
enhances
tinct and providing
Corner
original
ear level, and equidistant
a triangle,
speaker
in your
(SKF-580)
for the sound
so as to create
@ Center
or Onkyo's
tile overall
a solid anchor
with a real sense of movement
Discs, you can enjoy DTS and Dolby
Pro Logic IIx, DTS Neo:6,
@ Front
®
sound
hall. With Blu-ray
of tile LFE (Low'-Frefluency
and quality
on its position,
position.
In general,
by installing
the subwoofer
the wall, as shown.
in a front
of the bass output
the shape
a good
corner,
from your
of your listening
bass sound
or at one-third
room,
can be obtained
the width
of
while
bass,
at various
the one that
results.
En
11
Connecting the AV Receiver
Speaker Configuration
The following
depending
table indicates
on the number
For 7.1 -channel
speakers
the channels
of speakers
surround-sound
and a powered
you should
use
• Be careful not to short the positive and negative wires.
Doing so may damage the AV receiver.
• Make sure the metal core of the wire does not have contact with the AV receiver's rear panel. Doing so may
damage the AV receiver.
that you have.
playback,
you need seven
subwoofer.
Number of channels
Front speakers
Center speaker
Surround speakers
Surround back speaker*l*2
Surround back speakers*2
Front high speakers .2.3
"1 If you're using only one surround back speaker, connect it to
the SURR BACK OR FRONT HIGH L terminals,
*2 Front high and surround back speakers cannot be used at the
same time,
"3 When you connect the front high left and right speakers, prepare for it separately, or use the surround back left and right
speakers,
If you use 4 or 5 speakers,
connect
each of the two sur-
round speakers to the SURR [.JR terminals. Do not connect them to the SURR BACK OR FRONT HIGH L/R
or FRONT
HIGH OR ZONE
No matter
woofer
bass.
how many
2 L/R terminals.
speakers
is recommended
you use, a powered
for a really powerful
• Don't
minal.
To get the best from your surround
need to set the speaker
(_
sub-
and solid
settings.
sound
system,
• Don't
you
You can do this manually
35).
Speaker Connection Precautions
Read the following
before
• You can connect
speakers
6 and 16 ohms.
connecting
If you use speakers
ance, and use the amplifier
long period
your speakers:
with an impedance
at high volume
of time, the built-in
of between
with a lower
imped-
levels for a
amp protection
circuit
may be activated.
• Disconnect
making
the power
cord from the wall outlet
• Pay close attention
words, connect
to speaker
polarity.
In other
(+) terminals
only to positive
(+)
terminals,
and negative
(-) terminals
only to negative
(-)
terminals.
If you get them
sound will be out of phase
affect the sound
EF1
wiring
positive
• Unnecessarily
12
before
any connections.
the wrong
way around,
and will sound unnatural.
long, or very thin speaker
quality
the
and should
cables
be avoided.
may
connect
Doing
connect
more than one cable to each speaker
so may damage
one speaker
®
the AV receiver.
to several
terminals.
ter-
Connecting the Speaker Cables
Screw-type
speaker
insulation
speaker
terminals
from the ends of the
cables,
and twist the bare
Using
Banana
Plugs
(North
• If you are using banana
• Do not insert
Push-type
plugs,
the speaker
speaker
the speaker
_
1/2"_to 5/8"(12 _t° 15 '_mm) _'_
wires
as shown.
trip tightly,
1/2" to 5/8"
(12 to (Supplied
15 ram) of
speaker
cables are already stripped.)
_
American
tighten
code directly
surround
"_
models)
the speaker
terminal
into the center
before
inserting
hole of the speaker
the banana
plug.
terminal.
terminals
cables,
and twist the bare
wires tightly,
as shown.
Strip
(Supplied
3/8" speaker
to 1/2" (10
cables
to 12are
ram)
already
of insulation
stripped.) from the ends
The following
d_d_
illustration
back speaker,
shows which
connect
speaker
it to the SONN
should
be connected
I_1
of
3/8"
_ to 1/2"(10 c====_"_
to 12 mm)
to each pair of terminals.
BACK ON FRONT
Front
Surround
Surround
Surround
back right
speaker
back left
speaker
right
speaker
Surround
left
If you're
using only one
HIGH L terminals.
Front
left
right
speaker
speaker
Center speaker
speaker___
-Tan
- Brown
- Gray
- Blue
-
Red
White
BUBB BACK
OR
FRONT
HiGH SPEAKERS
SURR
SPEAKERS
FRONT
Green --/
SPEAKERS
)
Front high
right
speaker
(Optional)
Front high
left
speaker
(Optional)
Powe red
subwoofer
Using the supplied RCA cable, connect the subwoofer's
LINE INPUT jack to your AV receiver's SUBWOOFER
PRE OUT jack.
En
13
The speakers
can easily be wall mounted
hole slots. To prevent
the speaker
the wall, attach two of the supplied
by using the key-
from vibrating
against
thick rubber
stoppers
to the rear of each speaker.
To mount
the front,
vertically,
use the keyhole
on a screw that's
surround
and surround
back speakers
slot shown to hang each speaker
securely
screwed
• A mounting screw's ability to support a speaker depends
on how well it's anchored to the wall. If you have hollow
walls, screw each mounting screw into a stud. If there are
no studs, or the walls are solid, use suitable wall anchors.
• Use screws with a head diameter of 5116" (9 mm) or less
and a shank diameter of 118" (4 mm) or less. With hollow walls, use a cable/pipe detector to check for any
power cables or water pipes before making any holes.
into the wall.
• Leave a gap of between
Front speakers
of the screw head,
_J
Wall
3/16"
/
(5 mm) and 7/16" (10 mm)
between the wall and the base
(SKF-580)
./ Keyhole slot for wall
mounting
(We recommend
as shown.
that you con-
sult a home installation
profes-
sional.)
3/16" to 7/16"
(5 mm to 10 mm)
@
Surround
speakers/Surround
(SKR-580/SKB-580)
back speakers
Keyhole slot for wall
mounting
To mount
the center
speaker
horizontally,
hole slots shown to hang each speaker
are securely
screwed
Center speaker
We recommend using the provided rubber stoppers to
achieve the best possible sound from your speakers. The
rubber stoppers prevent the speakers from moving, providing a more stable platform. Use thick stoppers for the center speaker.
Thick rubber stoppers
use the two key-
Bottom of the
SKC-580
on two screws that
into the wall.
(SKC-580)
Keyhole slot for wall mounting
If the subwoofer
is placed
tile, etc.) and playback
may damage
the flooring.
plied pads underneath
provide
7-7/8" (200 mm)
a stable
on a hard floor (wood,
is very loud, the subwoofer's
To prevent
ER
14
feet
this, place the sup-
the subwoofer's
base for the subwoofer.
@
/
Pad
vinyl,
feet. The pads also
Connected image with AV components
HDMI
cable
Other
: Video & Audio
cables
: Video
: Audio
AV receiver
Blu-ray
TV, projector,
etc.
DVD
_===
AV receiver
j---
Disc/
Blu-ray
Game
player
console
TV, projector, etc.
Disc/
DVD player
Game
console
• Before making any AV connections, read the manuals supplied with your AV components.
• Don't connect the power cord until you've completed and double-checked all AV connections.
• Push plugs in all the way to make good connections (loose connections can cause noise or maltunctions).
• To prevent interference, keep audio and video cables away from power cords and speaker cables.
AV Cables and Jacks
Signal
Video
Audio
Jack
Cable
and
Description
HDMI
Video
Component
video
Y
Composite
Green
.....@
mue
Optical
audio
digital
Coaxial
audio
digital
nent video
Yellow
Composite
video is commonly
other video equipment.
v@
Optical
OPTICAL
[]
@
Orange
sound
_At
Analog
(RCA)
audio
1/8" (3.5 mm)
Stereo mini plug
Available
nection.
sampling
• The AV receiver
• The AV receiver's
Push
does
_{2N_
rate for PCM
not support
optical
digital
SCART
jacks
L@
White
R@
Red
is 32144.1148188.2196
digital
slightly
differently).
connections
used
allow
digital
kHz.
connections
is the same as optical.
Analog
audio
Even
connections
carries
176.4/192
analog
kHz
(RCA)
or DTS.
VCRs,
and
digital
The audio
you to enjoy digital
Digital
quality
on TVs,
you to enjoy
allow
such as PCM *, Dolby
This cable
,;>_-,
input signal
sockets
sound such as PCM*, Dolby Digital
quality is the same as coaxial.
Coaxial
=CTi_
The
Red
video
__
and audio.
Component
video separates
the luminance
(Y) and color
difference
signals (PB/CB, PR/CR), providing
the best picture quality (some TV manufacturers
label their compo-
_@
c_. @
Audio
HDM[ connections
call carry digital video
AV receiver is compliant
with HDM[.
HDMI
or DTS.
carry
analog
The audio
audio.
audio.
is effective
in case of the HDM[
con-
plugs.
have shutter-type
covers
that open
when
an optical
plug is inserted
and close when
it's removed.
plugs in all the way.
I [_,_'RRI,R1
• To prevent shutter damage, hold the optical plug straight when inserting and removing.
ER
15
VCR or DVD recorder/Digital
Video Recorder
[
]
TV, projector,
etc,
j
Satellite,
Connect
your
cable,
set-top
components
v': Assignment
can
box, etc,
to the
appropriate
be changed
(_
HDM[ IN 1
Output
Refer to "About
To listen
TV, projector,
(@ 60) and "Using
input
the sound
speakers
by the
setting
to an HDM[
source,
41)
to "On"
(_
HDM[
component
setting
from
of r-[I I-liD-compatible
through
return
speakers,
channel
AV receiver.
To use this function,
• To use ARC function,
Control"
ER
16
(ARC)
(ARC)
is set to "On"
TV's
or Recorder"
(@ 61).
speakers:
TV.
with
r-[I I-lID
ol- the "TV Control"
setting
to "Off".
External
Components"
set the HDM[
(_
17).
component
so that its video
to the AV receiver).
or the sound
to hear from
your TV's
the "TV
the AV receiver's
volume,
speakers
producing
an HDMI
capable
sound,
can be seen on the TV
[f the TV pow'er is off or the TV is set to
may be cut off.
speakers,
Control"
the AV receiver's
change
by controlling
setting
the AV receiver's
is set to "On"
speakers
the settings,
(_
41)
will produce
change
volume,
to hear from
sound while
your TV's
settings,
the
or turn
function
function
40).
v"
etc.
too. When
enables
you must select the TV/¢D
you must select the TV/¢D
(_
v"
box, etc.
TV, Player,
connected
40)
v"
Recorder
console
from the AV receiver
(_
v"
Video
to PCM.
the AV receiver
TV, by controlling
channel
setting
component
in no sound
set-top
the TV is not compatible
output
is set to "On"
the AV receiver's
Audio return
below.
player
recordeffDigital
cable,
your
see "Connecting
TV's speakers are muted. To stop the AV receiver's
down the AV receiver's
volume.
N Audio
through
40) when
audio
the input of the HDM[
this may result
or DVD
for all r'-tll-IID-compatible
the AV receiver,
TV OUT"
will be output
(_
player's
through
are shown
player
Assignable
an RIHD-compatible
HDMI IN jacks
to "On"
setting
assignments
Disc/DVD
HDM[ OUT
Disc/DVD
the "Audio
Blu-ray
Game
(on the TV, select
another
• When
Components
Audio/Video
HDM[ IN 4
TV OUT"
listening
screen
Signal
Satellite,
• To listen to TV audio
• When
input
HDM[ IN 3
received
• Set your Blu-ray
default
VCR
• Set the "TV Control"
• Set the "Audio
The
HDM[ IN 2
HDMI"
to audio
jacks.
Disc/DVD
34).
Jack
[nput
Blu-ray
TV to send the audio stream
to the HDMI
OUT of the
input selector.
input selector,
your TV must
support
ARC function
and "HDMI
0
"r'
,
Connect
your components
_: Assignment
oQ
Q_
@@ ,::! @ @
@
to the appropriate
can be changed
oD
jacks.
The default
input assignments
No.
Jack
%
COMPONENT
IN 1 (BD/DVD)
VIDEO
IN 2 (CBL/SAT)
DIGITAL
IN
Components
Component
video
Blu-ray
Disc/DVD
Satellite,
cable,
TV, projector,
OPTICAL
.! GAME)
Digital
BD/DVD
(BD/DVD)
(CBL/SAT)
OUT
Composite
video
IN
VCR/DVR
Analog
CBL/SAT
audio
IN
TV/CD
IN
1/
1/
Blu-ray
Disc/DVD
Satellite,
cable,
Blu-ray
Game
PORT
Analog
Video
1/
player
set-top
box, etc.
1/
etc.
Disc/DVD
player
cable,
audio/
set-top
box, etc.
console
TV, CD player,
audio
Cassette
UNIVERSAL
1/
console
Satellite,
Analog
box, etc.
VCR or DVD recorder/Digital
Video Recorder
IN
GAME
set-top
etc.
TV, projector,
and composite
video
IN
1/
player
TV, CD player
Game
audio
(TV/CD)
COAXIAL
MONITOR
below.
Assignable
Signal
OUT
%
are shown
(@ 34).
tape
Turntable*l
deck, MD,
Universal port optional
(UP-AI
etc.)
CD-R
dock
"1 Connect a turntable (MM) that has a phono preamp built-in. If your turntable (MM) doesn't have it, you'll need a commercially
available phono preamp.
If your turntable has a moving coil (MC) type cartridge, you'll need a commercially
well as a phono preamp. See your turntable's manual for details.
• With connection
ten and record
• With connection
• If your Blu-ray
output
_,
you can listen and record
audio from the external
audio from the external
components
_, you can enjoy Dolby Digital
Disc/DVD
using connection
player
in the main room;
and DTS. (To record
has both the main stereo
available MC head amp or MC transformer as
components
while you are in Zone 2. You can lis-
you can listen to the audio in Zone 2 as well.
or listen in Zone 2 as well, use _ and _.)
and multichannel
outputs,
be sure to connect
the main stereo
_.
N How to record the video
With the connections described above, you cannot record the video through the AV receiver. To make a connection for
video recording (@ 27).
En
17
• When
you connect
to both AUX
INPUT
will be given a higher priority.
• The AV receiver can output audio
AUDIO
`jacks and AUX
and video signals
from
the AUX
INPUT
LINE
INPUT
IN `jack at the same time, AUX
jacks to the VCR/DVR
INPUT
LINE
IN `jack
OUT jacks.
Step 1:
Make sure that each Onkyo component
with an analog
audio cable (connection
examples)
17).
(_
is connected
_
• Use only 1"-41cables
in the hookup
Make the R I connection
(see illustration
tional
below).
• Connect
Step 3:
using an RI Dock,
the Input
Display
or cassette
(_
tape deck,
• Some
23).
(DVD,
1"-41cables
are supplied
CD, etc.).
Interactive),
you can use the following
Change
components
components
components
either
addi-
components.
only Onkyo
the manuals
• While
With R I (Remote
special
1"-4I-capable
manufacturer's
If you're
for 1"-41connections.
players
• Some components
have two 1"-41`jacks. You can connect
one to the AV receiver.
The other,jack
is for connecting
Step 2:
change
with Onkyo
to 1"-41`jacks. Connecting
may cause
may not support
supplied
Zone 2 is on, the System
141 functions
all 1"-41functions.
with your other
other
a malfunction.
Onkyo
On/Auto
Refer
to
components.
Power
On and Direct
do not work.
functions:
N System
On/Auto
Power On
When you start playback
f-4 I, if the AV receiver
cally turn on and select
source.
N Direct
on a component
is on Standby,
connected
via
it will automati-
that component
as the input
Change
When playback
is started on a component
if4 I, the AV receiver
automatically
connected
selects
via
that compo-
nent as the input source.
N Remote
Control
You can use the AV receiver's
trol your other
f-4 I-capable
ing the remote
controller
control
sensor instead
the appropriate
ER
18
remote
remote
controller
Onkyo components,
at the AV receiver's
of the component.
control
to conpoint-
remote
You must enter
code first (_
51 ).
e,g,,
.e,g,,
CD player
__.j
DVD player
I
I
This section explains how to connect the supplied indoor FM antenna and AM loop antenna.
The AV receiver won't pick up any radio signals without any antenna connected, so you must connect the antenna to use
the tuner.
North American models
Insert
Asian models
the plug
into the jack,
Insert
Release,
wire,
Assembling the AM loop
antenna
Thumbtacks,
etc.
Indoor
FM antenna
(supplied)
AM loop
antenna
(supplied)
[ [0RIIIR'a_
• Be careful that you don't injure yourself when using thumbtacks.
• Once your AV receiver
reception.
• Keep
the AM
is ready
loop antenna
• If you cannot
achieve
• If you cannot
antelma.
achieve
good
good
for use, you'll
as far away
reception
reception
need to tulle into a radio station
as possible
fi'om your
with the supplied
with the supplied
indoor
indoor
AV receiver,
FM antenna,
and position
TV. speaker
cables,
try a commercially
AM loop antenna,
the antenna
to achieve
and power
cords.
available
outdoor
try using it with a commercially
the best possible
FM antenna
available
instead.
outdoor
AM
ER
19
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your components. Use the following sections as a guide.
The on-screen setup menus are displayed when:
• There is no video input, o1"
• The video input is 480p, 576p, 720p, 1080i,o1"1080p.
Video
Connection
Formats
Video component can be connected by using any one of the following video connection formats: composite video, component video, or HDMI, the latter offering the best picture quality.
Video Signal Flow Chart
When choosing a connection format, bear in mind that the
AV receiver doesn't convert between formats, so only outputs
of the same format as the input will output the signal.
[
Blu-ray Disc/DVD player, etc.
Composite
Component
]
HDMI
AV receiver
HO
Composite
O = m
Component
HDMI
TV, projector, etc.
Audio Connection
I
Formats
Audio Signal Flow Chart
Audio component can be connected by using any of the
following audio connection formats: analog, optical, coaxial, or HDMI.
When choosing a connection format, bear in mind that the
AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, audio signals
connected to an optical or coaxial digital input are not output by the analog VCR/DVR OUT.
I
Analog
Blu-ray Disc/DVD player, etc.
Optical
Coaxial
[
HDMI
AV receiver
Analog
If signals are present at more than one input, the inputs
will be selected automatically in the following order of priority: HDMI, digital, analog.
TV, projector, etc.
J
"1 Depends on the "Audio TV OUT" setting (_ 40).
*2 This setting is available, when "Audio Return Ch" setring is set to "Auto" (_ 40), you must select the TV/CD
input selector and your TV must support ARC function.
ED
20
Turning On/Off the AV Receiver
ON/STANDBY
STANDBY
indicator
\
I /
-
-"
MI
AX
OUTPUT
OUTPUT
LEVEL
control
LEVEL
Su bwoofe r's rear
panel
Front panel
Press
ON/STANDBY
Press
RECEIVER
The AV receiver
Remote controller
on the front
followed
comes
panel.
by ON/STANDBY
on, the display
on the remote
lights, and the STANDBY
controller.
indicator
goes off.
[ollj
_
The AV receiver
will enter Standby
mode. To prevent any loud surprises
the remote controller.
ress ON/STANDBY before
on the front panel or
you turn it off.
turn down the volume
when you turn on the AV receiver,
always
EF1
21
Basic Operations
You can display
various
information
input source as follows.
UNIVERSAL
m Operating
_Use
on the AV receiver
edly to cycle
the input selector buttons to select the input
source.
Start playback
See also:
on the source
component.
• Alternatively,
Other
Components"
• "Controlling
iPod"
(_
• "Listening
To adjust
control.
Select
information
Input source &
volume*l
24)
use the MASTER
the volume,
a listening
(_
the available
repeat-
information.
DISPLAY.
can typically
be displayed.
(O 51 )
47)
to the Radio"
to the
by DISPLAY
followed
through
you call use the AV receiver's
The following
• "Controlling
connected
PORT jack are excluded.)
RECEIVER
Press
about the current
(Components
/
i::?J_ ...i_ ./i i"_
,:.i.:.=?
1
VOLUME
Signal
format*2
or
sampling
frequency
mode and enjoy!
il)C .Z _i:,?,
_:.:},, .i ]
i)
See also:
• "Using
the Listening
• "Audyssey
Modes"
Settings"
(_
(_
28)
Input source &
listening mode*3
37)
N Operating with the remote controller
"1 When
AM or FM radio
frequency
Press RECEIVER
TOR.
by INPUT
followed
SELEC-
playback
on tile source
component.
See also:
Other
Components"
• "Controlling
iPod"
(_
• "Listening
tile volume,
a listening
(_
51 )
47)
to the Radio"
To adjust
(_
24)
Settings"
Modes"
(_
(_
is displayed
information
and
is dis-
the sampling
is digital
for about
is displayed
you have selected
frequency
but not PCM,
is
the signal
three
seconds,
then the pre-
reappears.
with
a name
The Music Optimizer
function
of compressed
tiles.
the default
in "Name
Edit"
name
(_
even
39).
music
MUSIC
The M.Opt
To set the level of the subwoofer,
LEVEL control.
use the OUTPUT
Because
to very low bass
our ears are less sensitive
• Alteruatively,
arrow
there's
woofer
too high. As a rule of thumb,
the sound quality
OPTIMIZER
indicator
on the front panel.
lights on the display.
you can use the remote
controller's
AUDIO
and
buttons.
• See "Music
sounds,
enhances
28)
Optimizer"
for more details
(_
42).
to set the level of the subset the subwoofer
level, and then back
You can adjust
the brightness
of the AV receiver's
Press RECEIVER followed
by
edly to select:
or normal
• Alteruatively,
American
Erl
input signal
*3 The input source
Press
level to what you think is the optimal
22
no format
is PCM,
information
37)
• When the subwoofer volume level is set to a positive (+) value,
the maximum master volume level is reduced proportionally.
it off slightly.
is analog,
displayed
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii,,,
a temptation
number,
VOL I/V.
use
mode and enjoy!
the Listening
• "Audyssey
preset
is displayed.
viously
when
See also:
• "Using
format
[fthe
[nformatiou
• "Controlling
Select
signal
If the input signal
displayed.
Start
is used, the baud,
are displayed.
*2 [f the input
played.
1
,....,...i:::."-"
dim, dimmer,
you can use the AV receiver's
models).
display.
DIMMER repeatbrightness.
DIMMER
(North
You can temporarily mute the output of the AV receiver.
The output is muted and the MUTING
indicator
Press RECEIVER
followed by MUTING.
flashes on the display.
When you connect an if4 I-capable Onkyo component, you
must configure the input display so that if41 can work
properly.
This setting can be done only from the front panel.
Press TV/CD,
panel
• To unmute, press MUTING again o1"adjust the volume.
• The Mute function is cancelled when the AV receiver is set to
GAME
or VCR/DVR
so that "TV/CD",
appears
"GAME"
on the front
or "VCR/DVR"
on the display.
Standby.
[g::i
F"i
ici{i!
With the sleep timer, you can set the AV receiver to turn
off automatically alter a specified period.
Press RECEIVER followed by SLEEP repeatedly
to select the required sleep time.
The sleep time can be set from 90 to 10 minutes in
10 minute steps.
The SLEEP indicator lights on the display when the
sleep timer has been set. The specified sleep time
appears on the display for about five seconds, then
the previous display reappears.
• ff you need to cancel the sleep timer, press SLEEP repeatedly
until the SLEEP indicator goes off.
• To check the time remaining until the AV receiver sleeps, press
SLEEP. Note that if you press SLEEP while the sleep time is
being displayed, you'll shorten the sleep time by 10 minutes.
{{{
Connect
a pair
of stereo
headphones
dard plug (1/4 inch or 6.3 ram)to
with a stanthe PHONES
jack.
• Always turn down the volume before connecting your headphones.
• While the headphones plug is inserted in the PHONES jack, the
speakers are turned off. (The Powered Zone 2 speakers are not
turned off.)
• When you connect a pair of headphones, the listening mode is
set to Stereo, unless it's already set to Stereo, Mono or Direct.
• Only the Stereo, Direct, and Mono listening modes can be used
with headphones.
Press
and hold down TV/CD,
(about
3 seconds)
to change
Repeat this step to select
or "TAPE".
For the TV/CD
changes
GAME or VCR/DVR
the input
"MD",
input selector,
display.
"CDR",
"DOCK"
the input display
in this order:
TV/CD+ MD + CDR
_-- TAPE
<-- DOCK
_J
For the GAME input selector, the setting changes in
this order:
GAME _-_ DOCK
For the
VCR/DVR input
changes
in this order:
VCR/DVR
selector,
the setting
_-_ DOCK
• DOCK can be selected for the TWCD, GAME or VCR/DVR
input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time (_ 51 ).
You can select the priority of the use of front high or surround back speakers.
Press RECEIVER followed by SP LAYOUT
repeatedly.
FrontHigh:
The sound from front high speakers is output
by priority.
SurroundBack:
The sound from surround back speakers is output by priority.
• ff the Powered Zone 2 is being used (_ 45), this setting cannot
be selected.
• When the listening mode that doesn't support front high or surround back speakers is used, the setting cannot be selected.
En
23
Listening to the Radio
N Manual tuning mode
Press TUNING
MODE so that the AUTO indicator
goes off on the display.
_Ldr!W_
Press
With the built-in
tuner you can enjoy
stations. You can store your favorite
quick selection.
This model changes
50/9kHz)
steps.
In manual
tuning
FM/AM
mode,
AM and FM radio
stations
as presets
for
TUNER
FM stations
to select
The frequency
button.
in 200/10kHz
(or
will be in mono.
either
"AM"
Each
changes
between
the radio band
AM and FM.
Band
into stations
ing the appropriate
Tuning into Radio Stations
controller,
mAuto tuning mode
display
Within
8 seconds,
For example,
iiiiiiiiiiiiiiiiiiiiiiiiiiiiii
MODE so that the AUTO
on the display.
Press
TUNING
Searching
indicator
l/¥.
stops when a station
is found.
When tuned into a station, the TUNED indicator lights.
When tuned into a stereo FM station, the FM STEREO
indicator lights on the display, as shown.
FM STEREO
I
FM STEREO
AUTO _- TUNE_ ,_
f..?:;..,
TUNED
En
24
"AM"
(Actual
the frequency
directly
hy enter-
frequency.
01
(Actual display depends on the country.)
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
by frequency
You can tune into AM and FM stations
On the remote
Frequency
lights
the frequency
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
manual tuning mode and listen to the station in mono.
edly to select
Press TUNING
to change
the
or "FM".
FM has been selected.
time you press TUNER,
repeatedly
when you release
one step at a time.
N Tuning
In this example,
l/¥.
stops changing
Press the buttons
frequency
Listening to the Radio
Press
and hold TUNING
depends
TUNER
press
or "FM",
followed
repeatby D.TUN.
on the country.)
use the number
of the radio
to tune to 87.50
buttons
to enter
station.
(FM), press 8, 7, 5, 0.
You can store a combination
FM/AM
radio stations
of up to 40 of your favorite
as presets.
Tune into the FM/AM station that you want to
store as a preset.
See the previous section.
When tuned into an RDS station, the RDS indicator lights.
Press MEMORY.
What is RDS?
The preset number flashes.
_=)i=i
_
While
.5.5
.]:.;
_.))?
_.:i-¢.:_:
the preset number
onds), use PRESET
through
Press
nel.
</_
is flashing
(about
8 sec-
to select a preset from 1
40.
M E MO RY again to store
The station
the station
or chan-
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed by
the European Broadcasting Union (EBU) and is available
in most European countries. Many FM stations use it these
days. In addition to displaying text information, RDS can
also help you find radio stations by type (e.g., news, sport,
rock, etc.).
The AV receiver supports four types of RDS information:
N PS (Program Service)
or channel
is stored and the preset num-
ber stops flashing.
Repeat this procedure
AM radio stations.
for all of your favorite
FM/
iiiiiiiiiiiiiiiiI
When tuned to an RDS station that's broadcasting PS
information, the station's name will be displayed. Pressing DISPLAY will display the frequency for 3 seconds.
N RT (Radio Text)
Selecting Presets
To select or
a preset,
use PRESET
</*"CHon+/-.
the AV
receiver,
the remote
controller's
When tuned to an RDS station that's broadcasting text
information, the text will be shown on the display as
described in the next section.
N PTY (Program Type)
This allows you to search for RDS radio stations by type
(_ 26).
• You call also use the remote controller's number buttons to select
a preset directly.
N TP (Traffic Program)
This anows you to search for RDS radio stations that
broadcast traffic information (@ 26).
Deleting Presets
• [n some cases,
Select the preset that you want to delete.
See the previous section.
While holding down MEMORY, press TUNING
MODE.
The preset is deleted and its number disappears from
the display.
iiiiiiiiiiiiiiiii!
the text characters
may not be identical
unexpected
characters
displayed
broadcast
on the AV receiver
by the radio station.
Also,
characters
may be displayed
when unsupported
are received.
This is not a malfunction.
• If the signal
displayed
to those
from
an RDS
intermittently
station
is weak,
RDS
data may be
or not at all.
When tuned to an RDS station that's broadcasting text
information, the text can be displayed.
Ell
25
Displaying Radio Text (RT)
Press
RT/PTY/TP
m RDS program types (PTY)
once.
I li! The UZ information
scrolls
across the display.
Type
Display
None
None
News
reports
Current
• The message "Waiting"
for the RT information.
may appear while the AV receiver waits
• If the message "No Text Data" appears on the display, no RT
information is available.
Finding Stations by Type (PTY)
News
affairs
Affairs
[nformation
[nfo
Sport
Sport
Education
Educate
Drama
Drama
Culture
Culture
Science
and technology
Varied
You can search for radio stations by type.
Press RT/PTY/'I'P twice.
Varied
Pop music
Pop M
Rock
Rock
M
Easy
M
music
Middle
The current program type appears on the display.
Use PRESET a/_ to select the type of program
you want.
See the table shown later in this chapter.
Science
Light
of the road
music
classics
Serious
Other
classics
music
Light
M
Classics
Other
M
Weather
Weather
To start tile search, press ENTER.
The AV receiver searches until it finds a station of
Finance
Finance
the type you specified, at which point it stops briefly
before continuing with the search.
Social
Children's
programmes
affairs
Religion
Children
Social
Religion
When a station you want to listen to is found, press
ENTER.
Phone
in
Travel
Phone
Travel
It no stations are found, the message "Not Found"
appears.
Leisure
Leisure
Jazz music
Jazz
Country
music
Country
National
music
Nation
[n
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii=
Listening to Traffic News (TP)
Oldies
Youcan search for stations that broadcast traffic news.
_
ress RT/PTY/TP
three times.
If the current radio station is broadcasting
TP (Traffic program),"[TP]" will appear on the display, and
{
{:
{
2{
tramc news will he heard as and when it's broadcast.
If"TP"
without
}that the station
To locate
ENTER.
square
a station
The AV receiver
i::
Erl
26
appears,
this means
WP.
that is broadcasting
TP, press
searches until it finds a station
broadcasting
TP.
If no stations
are found,
a mpears.
brackets
is not broadcasting
the message
that's
"Not Found"
music
M
Oldies
Folk music
Folk M
Documentary
Document
Alarm
TEST
Alarm
test
Alarm!
Recording
This section explains how to record the selected input source to a component with recording capability, and how to record
audio and video from different sources.
Connecting a Recording Component
Recording Separate AV Sources
Here you can record audio and video from completely
separate sources, allowing you to overdub audio onto your
video recordings. This function takes advantage of the fact
that when an audio-only input source (TV/CD) is selected,
the video input source remains unchanged.
In the following example, audio from the CD player connected to the TV/CD IN and video from the camcorder
connected to the AUX INPUT VIDEO jack are recorded
by the VCR connected to the VCR/DVR OUT jacks.
1
VCR,
Cassette, CDR,
DVD recorder
MD, etc.
• The AV receiver must be turned on for recording. Recording is
not possible while it's ill Standby mode.
• If you want to record directly from your TV or playback VCR to
the recording VCR without going through the AV receiver, connect the TV/VCR's audio and video outputs directly to the
recording VCR's audio and video inputs. See the manuals supplied with your TV and VCR for details.
• Video signals connected to composite video inputs call be
recorded only via composite video outputs. If your TV/VCR is
connected to a composite video input, the recording VCR must
be connected to a composite video output.
• The surround sound and DSP listening modes cannot be
recorded.
• Copy-protected Blu-ray discs and DVDs cannot be recorded.
• Sources connected to a digital input cannot be recorded. Only
analog inputs can be recorded.
• DTS signals will be recorded as noise, so don't attempt analog
recording of DTS CDs or LDs.
AV Recording
Audio sources can be recorded to a recorder (e.g., cassette
deck, CDR, MD) connected to the VCR/DVR OUT jacks.
Video sources can be recorded to a video recorder (e.g.,
VCR, DVD recorder) connected to the VCR/DVR OUT
jack.
Use the input selector
buttons
to select
the source
that you want to record.
You can watch the source while recording. The AV
receiver's MASTER VOLUME control has no effect
on recording.
On your
recorder,
start
recording.
[
VCR
CD player
.,_ : Video signal
*- : Audio signal
Prepare
back.
the camcorder
Prepare
the VCR for recording.
Press
ADX input
Press
TV/CD
and CD player
for play-
selector.
input
selector.
!ii!/l
This selects the CD player as the audio source, but
leaves the camcorder as the video source.
Start
recording
on the VCR and start
playback
on
the camcorder
and CD player.
The video from the camcorder and the audio from
the CD player
are recorded
by the VCR.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiii_
On the source
component,
If you select another
that input source
start
input source
playback.
during recording,
will he recorded.
ER
27
Using the Listening Modes
See
"About
Listening
Modes"
for detailed
information
about
the
listening
modes
(_
29).
Listening Mode Buttons
I Press
RECEIVER
first, 1
MOVIEiTV, MUSIC, GAME
,:_>
MUSIC-MOVIEiTV--
(i_ii:)
--
--_
_
,t<
,
_
GAME
_----STEREO
,<
<
MOVIE/TV button
This button selects the listening modes intended for use
with movies and TV.
MUSIC button
This button selects the listening modes intended for use
with music.
GAME button
This button selects the listening modes intended for use
with video games.
STEREO button
This button selects the Stereo listening mode and All
Channel Stereo listening mode.
• The Dolby
receiver
• The listening
Information"
• While
En
28
Digital
with
a pair
and DTS
a digital
modes
(_
audio
listening
modes
connection
you can select
can only
(coaxial,
depends
be selected
optical,
on the format
if your
Blu-ray
Disc/DVD
player
is connected
of the input
signal.
To check
listening
modes:
the format,
see "Displaying
22).
of headphones
is connected,
you can select
to the AV
or HDMI).
the following
Mono,
Direct,
and Stereo.
Source
,27t
vm , Na
The AV receiver's listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.
Explanatory Notes
SP LAYOUT
@ Front speakers
\77) ,._f;;;..... ki3
LISTENING
MODE--
i' --
..........
,_ El?-USTENING_OOE
@ Center speaker
=
@ Surround speakers
o
©
@ Surround back speakers
@ Front high speakers
(d {?
@ Subwoofer
m Input Source
The following audio formats are supported by the listening mode.
This is mono
(monophonic)
sound.
This is stereo
(stereophonic)
sound.
Two independent
audio signal
channels
are reproduced
through
two
speakers.
I g-lR'_
This is 5.1 -channel surround sound. This surround system has five main channels of sound and a sixth subwoofer channel (called the point-one channel).
This is 7.1 -channel surround sound. This is a further sound enhancement to 5.1 channel sound with two
additional speakers that provide greater sound envelopment and more accurate positioning of sounds.
This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded
channel from existing DTS 5.1 encoded material.
sixth
This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1 -channel
sources.
N Speaker Layout
The illustration shows which speakers are activated in each channel. See "Sp Config (Speaker Configuration)"
speaker setup (_ 35).
for the
Press RECEIVER followed by SP LAYOUT
repeatedly to select front high or surround back
speakers,
En
29
Listening Modes
Listening
Mode
Description
Direct
Input
Source
In this mode,
audio from
the input source
is output
without
NNNi1NN
surrotmd-sound
processing.
The "Sp Config" (presence
of speakers),
"Sp Distance"
and
"A/V Sync"s et tin g s are enable d, but m u c h o f t h e proc e ssillgs e t via AU D] O
is disabled.
See "Advanced
Setup"
for more
details
(_
Speaker
Layout
I_Jr',N
33).
IHI_:I
Stereo
Sound
Mono
Use this mode when watchiug
an old movie with a mouo souudtrack,
or use
it with the foreigu language
souudtracks
recorded
iu the left and right channels of some movies. It can also be used with DVDs or other sources coutaiu-
is output
by the front
iug multiplexed
Multichannel
This mode
M
audio,
left and right
such as karaoke
is for use with PCM
speakers
and subwoofer.
DVDs.
multichauuel
IHI_:I
sources.
:
Dolby
Pro Logic
IIx*2
Dolby
Dolby
Pro Logic
II
back. It provides a very natural aud seamless
fully euvelops the listener. As well as music
Pro Logic
IIx expands
any 2-channel
source
for 7. l-channel
play-
surrouud-souud
experience
that
and movies, video games can
also benefit from the dramatic
spatial effects and vivid imaging. If you're not
usiug any surrouud back speakers, Dolby Pro Logic II will be used instead
of Dolby Pro Logic IIx.
Dolby PLIIx Movie
Use this mode
TV, DVD,
Dolby
with any stereo
or Dolby
Surround
(Pro Logic)
movie
(e.g.,
VHS).
PLIIx
Music
Use this mode with any stereo
(e.g., CD, radio, cassette,
............................................................................................................
Dolby PLIIx Game
Use this mode
or Dolby
TV, VHS,
with video
games,
Surround
(Pro Logic)
music
source
DVD).
especially
those
that bear the Dolby
Pro
...........................................................................................................
Logic II logo.
Dolby
PLIIx
Movie,
These
modes
use the Dolby
sources
Dolby
Pro
Height
Logic
IIz
Dolby
for 7. l-chauuel
Pro Logic
EX
These
They're
encoded
rotating
[=rl
Music
IIx modes
to expaud
5. l-chauuel
playback.
IIz Height
is designed
but are particularly
modes
expaud
especially
surround
sion and provides
30
PLIIx
Pro Logic
to more
effectively
use existiug
program material when height channel speaker outputs are preseut. Dolby
Pro Logic IIz Height can be used to upmix a variety of sources from movies
aud music,
Dolby
Dolby
and fly-by
well-suited
to upmix
sources
for 6.1/7.
5. l-chauuel
game
couteut.
l-channel
playback.
suited to Dolby EX souudtracks
that include a matrixback chauuel. The additioual
channel adds an extra dimenau enveloping
sound effects.
surround
sound
experience,
[_-_'3
I_Jr',N
perfect
for
I_Jr',N
IHI_:I
[_-_'4
Listening Mode
Description
Dolby Digital
[n this mode, audio fl'om the input source is output without surround-sound
processing.
"Sp Config"
(presence
of speakers),
"{Trossovcr",
"Sp Dis-
Dolby
Digital
Plus*5
Input
Source
tance",
"A/V Sync" and much of the processing
See "Advanced
Setup" for more details (_ 33).
set via AUDIO
Speaker
Layout
are enabled.
IFa]'#,11
Dolby TrueHD
IFa]'#,11
DTS
DTS-HD High
Resolution Audio
IFa]'#,11
DTS-HD Master
Audio
IFa]'#,11
DTS Express
DSD*6
DTS 96/24"7
This
mode is for use with DTS 96/24
sources.
This
is high-resolution
with a 96 kHz sampling rate and 24-bit resolution,
providing
ity. Use it with DVDs that bear the DTS 96/24 logo.
DTS-ES Discrete*S
This
mode is for use with DTS-ES
Discrete
soundtracks,
crete surround back channel for true 6.117. l-channel
totally separate audio channels
provide better spatial
degree
sound
localization,
perfect
for sounds
DTS-ES
Matrix*S
r
DTS
Neo:6
This
mode
is for use with DTS-ES
Matrix
which
fidel-
use a dis-
playback.
The seven
imaging and 360-
that pan across
channels.
Use it with DVDs that bear the DTS-ES
a DTS-ES Discrete
soundtrack.
DTS
superior
the surround
logo, especially
soundtracks,
which
those
with
use a matrix-
encoded
back-channel
for 6.1/7. l-channel
playback. Use it with DVDs that
bear the DTS-ES logo, especially
those with a DTS-ES Matrix soundtrack.
This mode expands any 2-channel
source for up to 7. l-channel
playback.
uses seven full-bandwidth
channels
of matrix decoding
for matrix-encoded
material, providing
that fully envelops
• Neo:6 Cinema
a very natural
the listener.
and seamless
surround
Use this mode
• Neo:6 Music
with any stereo
movie
(e.g., TV, DVD,
Use this mode
with any stereo
music
source
VHS,
sound
It
experience
VHS).
(e.g., CD, radio,
cassette,
TV,
DVD).
This mode uses Neo:6
playback.
to expand
5. l-channel
sources
for 6.1/7. l-channel
[_-_'4
En
31
Onkyo-Original
DSP Listening Modes
Listening Mode
Description
Orchestra
Suitable
for classical
channels
beratiou
ill order to widen
of a large hall.
Suitable
for acoustic
Unplugged
frout stereo
Studio-Mix
Suitable
Input
Source
image,
ruusic,
iustrumeuts,
giving
vocals,
the impressiou
listeuiug
field with a powerful
This mode adds
realistic
surround
to the entire
effects
this ruode
the stereo iruage,
for rock or pop music,
lively sound
coucert.
TV Logic
o1"operatic
this ruode
of beiug
right
to music
and clarity
Game-RPG
Use this mode when
playing
role playing
game
Game-Action
Use this mode when
playing
action
discs.
Game-Rock
Use this mode when
playing
rock game
Game-Sports
Use this mode when
playing
sports
All Ch Stereo
Ideal for background
music,
reo sound
Full Mono
from the front,
In this mode,
all speakers
this mode
output
a
like being at a club or rock
in a TV studio,
to voices.
discs.
discs.
fills the eutire
and surround
the same
of where
the
discs.
game
surround,
hear is the same regardless
T-D (TheaterDimensional)
game
emphasizes
in this mode creates
image,
INi117N_9
rever-
in front of the stage.
to TV show's produced
sound,
the surround
the natural
and jazz,
acoustic
acoustics
eruphasizes
and siruulates
Speaker
Layout
souud
listeuiug
area with
ste-
INi11Ni117N_0
back speakers.
in mouo,
you are within
so the souud
the listening
you
room.
With this mode you cau eujoy a virtual surrouud souud eveu with only two or
three speakers. This works by coutrolliug
how' sounds reach the listener's
left
NNNi1NN
and right ears. Good results may not be possible
if there's too much reverb,
so we recommend
that you use this mode in an environment
with little or no
natural reverb.
"1 When
the input source
*2 If there
*3 Surround
back
*4 Front high
"6 AV receiver
Zone
front high
2 is being
Discs,
Dolby
Digital
signal
to the player.
is used
in a 3.1/5. l-channel
from
In that case,
on the input source,
speakers
Dolby
output
the sound.
Pro Logic
II is used.
HDMI
IN. Setting
set the output
speaker
the output
setting
*9 Output
can be switched
between
speakers,
front
on the player
on the player
side to PCM
might obtain
a better
on the "Sp
Config"
side to PCM.
DTS is used.
high or surround
back speakers
35)].
cannot
system.
setting
DTS is used.
back
modes
used,
are not supported.
are no surround
• The listening
En
front high channel,
or Powered
are not supported.
*8 If there
tiug (_
32
speakers,
can input the DSD
according
*7 Depending
the encoded
back
speakers
speakers
*5 For the Blu-ray
sound
contains
are no surround
be selected
with some
source
formats.
by pressing
SP
LAYOUT
[depending
set-
Advanced Setup
_o_
_,j
I
Remote indicator
q21_C_Jl}(_/i}C)
-- RECEIVER
The on-screen
• There
setup menus
is no video
• The video input
input,
are displayed
ENTER_,_',_
t/V/</_
when:
or
is 480p,
576p,
:u"
1080i, or 1080p.
SETUP
0
SetupMenu
®
$
,
BD/DVD
VCR/DVR
CBL/SAT
El
-- 2. Component
3. DigitalAudio
-- 4. Sp Config
-- 5. Sp Distance
-- 6. LevelCal
-- 7. AudioAdjust
-- 8. NameEdit
-- 9. Hardware
-- 10. HDMISetup
@ HDMI Input (_ 34)
@
(@ 34)
@ Sp Config (_ 35)
Front
Center
Surround
FrontHIgh
SurrBack
SurrBack Ch
Crossover
Double Bass
@
Sp Distance
!0_i
!ijj_!!;!i
Left
FrontHIgh Left
Center
FrontHIgh Right
Right
Surround Right
SurrBack Right
SurrBack Left
Surround Left
Subwoofer
on the connected
TV
by using the on-screen
display.
i
(_
Audio
[_'/41/,/2
iD/,/I IN3
VCLgVR
CDL}S/k_
GAM
_UX
TWO
PORI
(3 36)
• If the main
menu
ate external
input
doesn't
appear,
is selected
make
on your
sure the appropri-
TV.
Use 1,/¥ to select a menu, and then press ENTER.
Use &/¥ to select
target,
and </I,_
to change
the
setting.
Edit (_
39)
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!i
(_) Hardware
Component
Digital Audio
Sp Conflg
Sp Distance
Level Cal
Audio Adjust
Name Edit
Hardware
10. HDMI Setup
Adjust
Input Ch(Mono)
Panorama
Dimension
Center Width
Height Gain
Dolby EX
Center Image
Audyssey
Dynamic EG
Reference Leve
Dynamic Volume
Listening Angle
(_) Name
Setup Menu
2.
3.
4.
5.
6.
7.
8.
9.
(_
Press SETUP to
close the menu.
Press
to return to the main menu.
RETURN
39)
Front High/Zone2
SurrBk/FrontHIgh
Remote ID
FM/AM Freq Step
(@ 36)
out the settings
appear
way to change the AV receiver's
are organized into ten categories
:
FrontHIgh Right
Right
Surround Right
SurrBack Right
SurrBack Left
Surround Left
Subwoofer
Audio
Carry
:
GAME
AUX
TV/CD
PORT
Digital
setup menus
and provide a convenient
various settings. Settings
on the main menu.
(_) Level Cat (_ 36)
FrontHIgh Left
Center
iiiiiiiiiiiiiiiiiiiiii!i_B!i!!!i:iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
VCR/DVR
CBIJSAT
GAME
AUX
TV/CD
PORT
..........
The following menu appears.
VCR/DVR
CBIJSAT
VCR/DVR
CBL/SAT
GAME
AUX
TV/CD
PORT
/
--RETURN
Press RECEIVER followed by SETUP.
ef _
(_ 34)
The on-screen
AUX
TV/CD
PORT
BDIDM_
(_) Component
VI;
?Y,t_:i
720p,
xi:_
¢_'
• This procedure
using SETUP,
can also be performed
arrow
buttons,
on the AV receiver
by
and ENTER.
@ HDMI Setup (@ 40)
LlpSync
HDMI Control
Audio Return Ch
Power Control
TV Control
ED
33
/
Explanatory Notes
[#fe]iil_Ze]i[:.liJiE(efeIial_Ze]i[:.liJi_[_olllil_1!k_ll
Subwoofer
If you connect a video component to a component video
input, you must assign that input to an input selector. For
example, if you connect your Blu-ray Disc/DVD player to
COMPONENT VIDEO IN 2, you must assign "IN2" to
the "BD/DVD" input selector.
Here are the default assignments.
-_Yes:
elect if a subwoofer is connected.
Select if no subwoofer is connected.
(_) Menu selection
Input
(_) Setting target
BD/DVD
@ Setting options (default setting underlined)
Default assignment
selector
INI
VCR/DVR
CBL/SAT
IN2
GAME
l_lJ]_ffllTl:'Trd
AUX
TV/CD
PORT
If you connect a video component to an HDMI input, you
must assign that input to an input selector. For example, if
you connect your Blu-ray Disc/DVD player to HDMI
IN 2, you must assign "HDMI2" to the "BD/DVD" input
selector.
Here are the default assignments.
Input
N BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/
CD, PORT
IN1, IN2:
Select a corresponding component video input that
the video component has been connected.
Default assignment
selector
BD/DVD
HDMII
VCR/DVR
HDMI2
CBL/SAT
HDMI3
(;AME
HDMI4
Select if you're not using the COMPONENT
VIDEO OUT.
• If you connect
a component
(such
as UP-AI
Dock
that
seated
iPod) to the UNIVERSAL PORT jack, you cannot assign any
input to PORT selector.
AUX
TV/CD
PORT
m BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/
CD, PORT
HDMI1, HDMI2, HDMI3, HDMI4:
Select a corresponding HDMI input that the video
component has been connected.
Select if you're not using the HDMI OUT.
Each HDMI input cannot be assigned to two input
selectors or more. When HDMI1 - HDMI4 have
already been assigned, you must set first any unused
input selectors to ....
, or you will be unable to
assign HDMI1 - HDMI4 to input selector.
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTIGAL IN 1, you
must assign "OPTI" to the "TV/CD" input selector.
Here are the default assignments.
Input
selector
BD/DVD
Default assignment
COAXI
VCR/DVR
CBL/SAT
COAX2
GAME
OPTI
AUX
• When
here,
all HDMI
the digital
IN is assigned
audio
to an input selector
input for that input selector
as explained
is automati-
set to the same HDMIIN (÷ 34, Digital Audio (Digital
Audio Input)).
cally
• If you connect
a component
iPod) to UNIVERSAL
to PORT
selector.
PORT
• Do not assign the component
TV/CD
selector
when
(such
as UP-AI
Dock
jack, you cannot
connected
you set "TV
that
assign
any input
with the HDM[
Control"
setting
seated
input to
to "On"
(3 41 ). Otherwise, appropriate CEC (Consumer Electronics
operation
will not be guaranteed.
Control)
Er3
34
TV/CD
OPT2
PORT
N BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/
CD, PORT
COAX1, COAX2, OPT1, OPT2:
Select a corresponding digital audio input that the
component has been connected.
Select if the component is connected to an analog
audio input.
• When
an NDMI
IN is assigned
to all input
selector
ill "HDM[
[nput" (3 34), this input assignment
is automatically
same NDMI IN. And ill addition to the usual inputs
set to the
(e.g.,
COAXl,
inputs.
COAX2,
etc.),
you can also
select HDM[
• Available
sampling rate for PCM signals
(optical and coaxial) is 32/44.1/48/88.2/96
• If you connect
a component
(such
iPod) to the UNIVERSAL
input to PORT
from a digital input
kHz/16, 20, 24 bit.
as UP-AI
PORT
jack,
Dock
that seated
you cannot
assign
ally
selector.
*5 If the "Surround" setting is set to "Snmll", the "Large"
option cannot be selected.
*6 For "Front High", the default is "None".
*7 If the "Front High/Zone2" setting is set to "Zone2", this setting cannot be selected.
m SurrBack
Ch
lch:
Select
if only
one
if two
(left
surround
back
speaker
is con-
nected.
2ch:
Select
and right)
surround
back
speakers
are connected.
• If the "SurrBaek"
selected.
This section explains how to specify
which speakers are connected and their
sizes.
For speakers with a cone diameter
larger than 6-112 inches (16 cm), specify Large (full band). For those with a
Gone diameter
smaller diameter, specify Small
(default crossover 100 Hz).
The crossover frequency can be changed in the "Crossover
(Crossover Frequency)" (_ 35).
These
settings
are disabled
• a pair of headphones
is set to "None",
this setting cannot
be
m Crossover (Crossover Frequency)
This setting is advantageous for the speakers that you
specified as "Small" in the "Sp Config (Speaker Configuration)" (3 35). To get the best bass performance from
your speaker system, you need to set the crossover frequency according to the size and frequency response of
your speakers.
40Hz, 50Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz,
200Hz:
Use the diameter of the smallest speaker in your system
when choosing the crossover frequency.
when:
is connected,
setting
or
• the "Audio TV OUT" setting is set to "On"
selector other than HDM[ is selected.
(3
40) and an input
N Subwoofer
_Yes:
Select if a subwoofer is connected.
No:
Select if no subwoofer is connected.
Speaker
cone diameter
Crossover frequency
Over 8 in. (20 cm)
40150160 Hz*
6-112 to 8 in. (16 to 20 cm)
80 Hz
5-114 to 6-112 in. (13 to 16cm)
100Hz
3-112 to 5-114 in. (9 to 13 cm)
120Hz
Under 3-112 in. (9 cm)
1501200 Hz*
Choose
the setting
suitable
for the speaker.
m Front
Small:
• For a more accurate
Large:
the manuals
Select based on the cone diameter.
• If the "Subwoofer"
"Large"
and does
setting
is set to "No",
setting,
supplied
with
• Choose a higher crossover
from your subwoofer.
this setting
is fixed at
look up the frequency
your
speakers
frequency
response
in
and set accordingly.
if you want
more sound
N Double Bass
not appear.
m Center*l, Surround*l,
SurrBack*l*2*3*5*7
Front High*l*2*4*6*7
• This function
"Yes",
can be set only if the "Subwoofer"
and the "Front"
setting
is set to "Large"
setting
(3
is set to
35).
Small:
Large:
Select
based
on the
cone
With the Double Bass function, you can boost bass output by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
On:
diameter.
None*6:
Select if no speaker is connected.
Double
Bass
function
on.
Bass
function
off.
Off:
"1 If the "Front"
setting
cannot be selected.
*2 If the "Surround"
be selected.
is set to "Small",
setting
is set to "None",
*3 If the "SurrBk/FrontHigh"
(3
39), this setting
*4 If the "Front
cannot
option
this setting
is set to "Front
Double
cannot
High"
be selected.
High/Zone2"
"SurrBk/FrontHigh"
this setting
setting
cannot
the "Large"
setting
setting
be selected.
is set to "Zone2"
is set to "SurrBack"
and
(3
39),
Ell
35
• If you're
using a handheld
each speaker so that it reads
measured
with C-weighting
sound
level meter,
adjust
75 dB SPL at the listening
and slow' reading,
the level of
position,
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener's ears as the sound designer
intended.
m Unit
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
feet:
Distances can be set in feet. Range: lit to 30ft in
1 foot steps.
meters:
Multiplex/Mono
Distances can be set in meters. Range: 0.3m to 9.0m
in 0.3 meter steps.
(The default setting varies from country to country.)
m Left, FrontHigh Left, Center, FrontHigh Right,
Right, Surround Right, SurrBack Right,
SurrBack Left, Surround Left, Subwoofer
Specify the distance from the each speaker to your listening position.
• the "Audio
input
• Speakers
(Speaker
selector
other
setting
than HDMI
(_
40)
is selected.
in the "Sp Config
35) cannot
be selected.
Subwoofer
and Front High
Both the main and sub channels are output.
Mono
Configuration)"
Right,
The main channel is output.
Sub:
and an
or "None"
(_
I Input Ch(Mux)
Main:
or
is set to "On"
that you set to "No"
• The Center,
•
is connected,
TV OUT"
Multiplex
This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or
languages with multiplex sources, multilingual TV broadcasts, and so on.
The sub channel is output.
M/S:
• These settings are disabled when:
• a pair of headphones
Settings
distances
can be
set up to 5 ft, (1,5 m) more or less than the "Left" distance, For
example,
if the "Left" distance is set to 20 ft. (6 m), the Center,
Right, Subwoofer,
Front High Left and Front High Right distances can be set between 15 and 25 ft. (4.5 and 7.5 m).
The Surround and Surround Back distances can be set up to 5 ft.
(1.5 m) more or 15ft. (4.5 m) less than the "Left" distance. For
example,
if the "Left" distance is set to 20 ft. (6 m), the Surr
Right, Surr Left, Surr Back R and Surr Back L distances can be
set between 5 and 25 ft. (1.5 and 7.5 m).
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode.
I Input Ch(Mono)
L+R:
Both the left and right channels are output.
Left:
Only the left channel is output.
Right:
Only the right channel is output.
Dolby Settings
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
I Left, FrontHigh Left, Center*l, FrontHigh Right,
Right, Surround Right, SurrBack Right,
SurrBack Left, Surround Left
-12 dB to 0 dB to +12 dB in l dB step.
I Subwoofer*l
!
(Speaker
that you set to "No"
or "None"
in the "Sp Config
Configuration)"
35) cannot
be selected.
(_
• The speakers cannot be calibrated
while a pair of headphones
connected
or the AV receiver is muted or "Audio TV OUT"
ting is set to "On"
"1 For the center
Ell
36
(÷
speaker
by using AUDIO
is
set-
40).
and subwoofer,
are saved.
the level
Music
(2ch Input)
These
settings
apply to only 2-channel
If you're
not using any surround
stereo sources.
back speakers,
tings apply to Dolby Pro Logic II, not Dolby
IIx.
these set-
Pro Logic
I Panorama
in:
Panorama function on.
iff:
Panorama function off.
With this setting, you can broaden the width of the front
stereo image when using the Dolby Pro Logic IIx Music
listening mode.
-15 dB to 0 dB to +12 dB in l dB step.
• Speakers
PLIIx
settings
made
m Dimension
-3 to 0 to +3
With this setting,
or backward
listening
you can move the sound field forward
when using the Dolby Pro Logic IIx Music
mode.
backward.
Higher
Lower
settings
settings
move the sound field
move it forward.
If the stereo image feels too wide, or there's too much
surround sound, move the sound field forward to
improve
the balance.
Conversely,
m Center
not enough
surround
With this setting,
you can adjust the width
from the center speaker
Logic IIx Music
of the sound
when using the Dolby
listening
using a center speaker,
mode. Normally,
uted to the front left and right speakers
This setting
sound
(If you're
the center channel sound
controls
Pro
is out-
not using a
will be distribto create a phan-
the front
left, right,
and center mix, allowing you to adjust the weight
center channel sound.
Height
the listener
to select
how much
Pro Logic
and the front high speakers
"Mid"
IIz enables
gain is applied to the front
There are three settings,
order. While
is the default
"Low",
"Mid"
are accentuated
listening
setting,
and
in that
the lis-
tener may adjust the Height Gain Control to their personal
preference.
m Height
you can specify
and right channel output
the center channel.
Setting
Sound
Gain
Low PLIIz Height
Gain becomes
a value "0" in the middle
in order to create
is set to hear a sound.
is spread in left and right (the outside)
set value is made big. Please
so that the
adjust by liking.
Audyssey Settings
Off:
i
No Audyssey
EQ TMequalizing
will apply.
On:
"Dynamic
available.
EQ" and "Dynamic
The Audyssey
N Dynamic
active.
indicator
Volume"
become
will light ('@ 8).
EQ
Off:
Mid:
Medium
PLIIz Height Gain becomes
active.
High:
High PLIIz Height
Gain becomes
active.
Audyssey
On:
Dynamic
EQ off.
Audyssey
Dynamic
EQ on.
The Dynamic
• [f the "Front High" setting is set to "None" (3 35), o1""Front
High/Zone2" setting is set to "Zone2" (3 39), this setting is
fixed at "Mid" and does not appear.
EX
This setting
determines
are handled.
This setting
back speakers
Dolby
by how much the front left
is attenuated
• Audyssey equalizing does not work for DSD sources.
Low:
Dolby
mode creates 6-channel
stereo sources. With
m Audyssey
Gain Control in Dolby
"High",
of the
Gain
The Height
high speakers.
The DTS Neo:6 Music listening
surround sound from 2-channel
this setting,
if you're
the center channel
put by only the center speaker.
PLIIz
Music
m Center Image
_0to2to5
_0to3to7
tom center).
• If the "Front High/Zone2" setting is set to "Zone2" (3 39),
this setting is fixed at "Manual" and does not appear.
Neo:6
Width
center speaker,
• If the "Front High" setting is set to other than "None", this setting is fixed at "Manual" (3 35).
DTS Setting
if the stereo image
feels like it's in mono, or there's
sound, move it backward.
• If the "SurrBack"
Setting is set to "None" (3 35), this setting
cannot be selected.
how Dolby
are connected.
Digital,
Dolby
EX encoded
is unavailable
Digital
signals
is effective
Plus and Dolby
Dynamic
Audyssey
Dynamic
with
TrueHD
at low volume
EQ solves the problem
8).
levels.
of deterio-
rating sound
quality
as volume
is decreased
into account
human
perception
and room
acoustics.
It
the correct
frequency
response
and
surround
content
volume
sounds
levels moment-by-moment
the way it was created
level -- not just at reference
only.
will light (_
EQ rr_l, you can enjoy great
sound even when listening
does so by selecting
if no surround
This setting
With Audyssey
EQ indicator
by taking
so that the
at any volume
level.
N Dolby EX
Auto:
If the source
Dolby
signal contains
EX listening
a Dolby
EX flag, the
• The setting is stored individually
for each input selector.
• If Direct listening mode is selected, this setting cannot be
selected.
mode is used.
Manual:
You can select
any available
listening
mode.
EF1
37
/
m Reference Level
Audyssey Dynamic EQ TM Reference Level Offset
_0 dB:
It should be used when listening to movies.
_5 dB:
Select this setting for content that has a very wide
dynamic range, such as classical music.
} 10 dB:
Select this setting for jazz or other music that has a
wider dynamic range. This setting should also be
selected for TV content as that is usually mixed at
10 dB below film reference.
} 15 dB:
Select this setting for pop/rock music or other program material that is mixed at very high listening
levels and has a compressed dynamic range.
Movies are mixed in rooms calibrated for film reference. To achieve the same reference level in a home theater system each speaker level must be adjusted so that
-30 dBFS band-limited (500 Hz to 2000 Hz) pink noise
produces 75 dB sound pressure level at the listening
position. A home theater system automatically calibrated by Audyssey EQ T_ will play at reference level
when the master volume control is set to the 0 dB position. At that level you can hear the mix as the mixers
heard it.
Audyssey Dynamic EQ T_ is referenced to the standard
film mix level. It makes adjustments to maintain the reference response and surround envelopment when the
volume is turned down from 0 dB. However, film reference level is not always used in music or other non-film
content. Audyssey Dynamic EQ Reference Level Offset
provides three offsets from the film level reference
(5 dB, 10 dB, and 15 dB) that can be selected when the
mix level of the content is not within the standard.
About Audyssey Dynamic EQ
Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking
into account human perception and room acoustics.
Dynamic EQ selects the correct frequency response and
surround levels moment-by-moment at any userselected volume setting. The result is bass response,
tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines
information from incoming source levels with actual
output sound levels in the room, a prerequisite for delivering a loudness correction solution.
Audyssey Dynamic EQ works in tandem with
Audyssey EQ to provide well-balanced sound for every
listener at any volume level.
About Audyssey Dynamic Volume
Audyssey Dynamic Volume solves the problem of large
variations in volume level between television programs,
commercials, and between the soft and loud passages of
movies. Dynamic Volume looks at the preferred volume
setting by the user and then monitors how the volume of
program material is being perceived by listeners in real
time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary
rapid or gradual adjustments to maintain the desired
playback volume level while optimizing the dynamic
range. Audyssey Dynamic EQ is integrated into
Dynamic Volume so that as the playback volume is
adjusted automatically, the perceived bass response,
tonal balance, surround impression, and dialog clarity
remain the same whether watching movies, flipping
between television channels, or changing from stereo to
surround sound content.
Theater-Dimensional
• If "Dynamic EQ" setting is set to "OFF',this setting cannot be
selected.
• The setting is stored individually for each input selector.
m Dynamic Volume
Off:
Audyssey Dynamic Volume TM off.
Light:
Light Compression Mode becomes active.
Medium:
Medium Compression Mode becomes active.
Heavy:
Heavy Compression Mode becomes active. This setting affects volume the most, causing all sounds to
be of equal loudness.
Setting
I Listening Angle
Wide:
Select if the listening angle is 40 degrees.
Narrow:
Select if the listening angle is 20 degrees.
With this setting, you can optimize the Theater-Dimensional listening mode by specifying the angle of the
front left and right speakers relative to the listening
position. Ideally, the front left and right speakers should
be equidistant from the listening position and at an
angle close to one of the two available settings.
Front left speaker _
_
Front right speaker
/
"_ _"20°140 °
• If you make
"Dynamic
cator
EQ"
• If Direct
selected.
ED
"Audyssey"
and
are set to "On". The Dynamic
Vol indi-
8).
is stored
listening
Volume "lMactive,
settings
will light (3
• The setting
38
Dynamic
individually
mode
is selected,
for each input
this setting
selector.
cannot
be
I SurrBk/FrontHigh
Front High:
Front high speakers can be used.
SurrBack:
rv_g!m,_NN_
You can enter a preset name for each individual input
selector for easy identification. When entered, the preset
name will appear on the display.
Preparation
Press
the input selector
buttons
to select an input source.
Surround back
Select "Front High"
speakers to FRONT
R terminals, and the
OR FRONT HIGH
!
• If the "Front
m Name
setting
- - -, Blu-ray, DVD, HD DVD, VCR, DVR, Tivo,
CahleSTB, SAT STB, PS3, Wii, Xhox, PC, TV, CD,
TAPE, iPod:
To reset to the default, select "- - -".
speakers can be used.
if you've connected your Zone 2
HIGH OR ZONE 2 SPEAKERS L/
front high speakers to SURR BACK
SPEAKERS L/R terminals.
High/Zone2"
setting
is set to "Front
High",
this
is set to "SurrBack".
Remote Control Settings
m Remote ID
_1,2, or3
• Can not set the input
• This menu
cannot
selector
be used
by the same name.
for the TUNER
input
selector.
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can
change its remote ID from 'T', to "2" or "3".
• If you do change
Speaker Settings
you change
these
settings,
turn down
the volume.
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
6ohms:
Select if the impedances of all speakers are between
6 and 16 ohms.
American
impedance
models)
Do not support
speakers
with an
of less than 6 ohms.
N Front High/Zone2
Front High:
Front high speakers can be used.
Zone2:
Zone2 speakers can be used.
Select "Zone2" if you've connected your Zone 2 speakers
to FRONT HIGH OR ZONE 2 SPEAKERS L/R terminals (_ 44).
[D, be sure to change
you
Changing
the Remote
Controller's
While
holding
down
down
SETUP
until
ID
RECEIVER,
the remote
press
and hold
indicator
lights
....................................
(about 3 seconds).
Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice.
N Sp Impedance
4ohms:
• (North
remote
i
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
• Before
the AV receiver's
the remote controller
to the same [D (see below), otherwise,
won't be able to control it with the remote controller.
FM/AM Frequency Setup Settings
For FM/AM tuning to work properly, you must specify the
FM/AM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
m FM/AM Freq Step (North American models)
200k/10kHz:
Select if 200 k/l 0 kHz steps are used in your area.
50k/9kHz:
Select if 50 k/9 kHz steps are used in your area.
m AM Freq Step (Asian
10kHz:
models)
Select if 10 kHz steps are used in your area.
9kHz:
Select if 9 kHz steps are used in your area.
E[3
39
/
_'/Wl4p
• When set to "On" and close the menu, the name of connected
I-liD-compatible
m Audio
TV OUT
Off:
HDMI
On:
HDMI
audio is not output.
audio is output.
This preference
determines
whether
audio received
at the
HDMI IN is output by the HDMI OUT. You may want to
turn this preference
on if your TV is connected
to the
HDMI OUT and you want to listen to the audio from a
component
that's connected
to an HDMI IN, through your
TV's speakers.
Normally,
this should
be set to "Off".
• If "On" is selected and the signal call be output by the TV, the
AV receiver will output no sound through its speakers.
• ff "On" is selected, "TV Sp On" appears on the display by
pressing DISPLAY.
• When "TV Control"
"Auto".
is set to "On", this setting is fixed to
• With some TVs and input signals, no sound may be output even
when this setting is set to "On".
• When the "Audio TV OUT" setting is set to "On", or "TV Control" is set to "On" and you're listening through your TV's
speakers (_ 16), if you turn up the AV receiver's volume control, the sound will be output by the AV receiver's front left and
right speakers. To stop the AV receiver's speakers producing
sound, change the settings, change your TV's settings, or turn
down the AV receiver's volume.
lip sync disabled.
can be set to automatically
delay between the video and the audio,
from the connected
monitor.
correct
Lip Sync function on the A/V Sync screen.
Control
(RIHD)
Off:
F-UHD
disabled.
On:
F-UHD
enabled.
This function allows r-UHO-compatible
components
connected via HDMI to be controlled with the AV receiver
Ell
• Refer to the connected component's
details.
N Audio
Return
60 to 62).
instruction
manual for
Ch (ARC)
Off:
Select "OFF' if you don't
channel (ARC) function.
want to use audio return
Auto:
The audio signal from your TV tuner can be sent to
the HDMI OUT of the AV receiver.
channel
(ARC)
function
TV to send the audio
the AV receiver.
enables
stream
to the
To use this function,
an HDMI
HDMI
you must
and your TV must support
any
based on the data
• This function works only if your HDM[-compatible TV supports
HDM[ Lip Sync.
• You can check the amount of delay being applied by the HDM[
4O
• If movement is unnatural when set to "On", change the setting
to "Off'.
select the TV/CD input selector
ARC function.
lip sync enabled.
The AV receiver
(_
• Set to "OIT' when a connected piece of equipment is not compatible or it is unclear whether the equipment is compatible or
not.
OUT of
Enable:
N HDMI
• When an _ I-liD-compatible component is connected to the
AV receiver via the HDMI cable, the name of the connected
component is displayed on the AV receiver display. For example,
while you are watching TV broadcasting, if you operate a
Blu-ray Disc/DVD player (being powered on) by the remote
control of the AV receiver, the name of the Blu-ray Disc/DVD
player is displayed on the AV receiver.
1.4 capable
Disable:
HDMI
nent, it is displayed as "Player*" or "Recorder*", etc ("*" means
the number of two or more component).
When set to "OFF' and close the menu, "RIHD OfF' are displayed on the AV receiver.
"Disconnect" --+ "RIHD Off'
Audio return
N LipSync
HDMI
components and "RIHD On" are dis-
played on the AV receiver.
"Search..."
--->"(name)" --->"RIHD On"
When the AV receiver cannot receive the name of the compo-
• The "Audio Return Ch" setting can be set only when the above
"HDMI Control" setting is set to "On".
• This setting is set to "Auto" automatically when the above
"HDMI Control" is set to "On" first time.
N Power Control
Off:
Power Control disabled.
On:
Power Control enabled.
To link the power functions of r41l-llO-compatible
components connected via HDMI, select "On".
This setting is set to "On" automatically when the above
"HDMI Control" is set to "On" first time.
• The "Power Control" setting call be set only when the above
"HDMI Control" setting is set to "On".
• HDMI power control only works with f"411-11_-compatible
components that support it and may not work properly with
some components due to their settings o1"compatibility.
• When set to "On", power consumption will increase.
• When set to "On", regardless of whether the AV receiver is On
or in Standby, both audio aud video stream from an HDMI iuput
will be output to the TV or other components via HDMI connection (HDMI pass through function). Wheu the HDMI pass
through function activates in standby mode, HDMI THRU indi-
You can change various audio settings by pressing
AUDIO.
These
• Refer to the connected compoueut's
details.
when:
Press RECEIVER followed by AUDIO.
Use h/¥
to select
an item, and
m/_" to change
the
setting.
Repeat
instruction manual for
are disabled
• the "Audio TV OUT" settiug is set to "On" (_ 40) and an input
selector other than HDMI is selected.
cator will light.
• The power consumption duriug standby mode will increase during the HDMI pass through function; however in the following
cases, the power cousumptiou can be saved:
1. The TV is in standby mode.
2. You are watching a TV program.
settings
• a pair of headphoues is connected, or
this step for the other settings.
Tone Control Settings
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
N TV Control
Off:
N Bass
TV Control
disabled.
-10 dB to 0 dB to +10 dB in 2 dB steps
On:
TV Control
You can boost or cut low-frequency
enabled.
sounds
output
by the front speakers.
Set to "On" when you want to control
from an 1-411-lD-compatible
HDMI.
the AV receiver
TV that is connected
to
N Treble
i
-10 dB to 0 dB to +10 dB in 2 dB steps
You can boost or cut high-frequency
sounds
output
by the front speakers.
• Do not assigu the compoueut connected with the HDMI input to
the TV/CD selector when you set "TV Control" setting to "On".
Otherwise, appropriate CEC (Consumer Electronics Control)
operatiou is uot guaranteed.
• Set to "Off" when the TV is not compatible or when it is unclear
whether the TV is compatible or not.
• To bypass the bass and treble tone circuits, select the Direct listening mode.
• This procedure can also be performed on the AV receiver by
using its TONE, -, and + buttons (_ 43).
• The "TV Control" setting can be set ouly when the above
"HDMI Control" and "Power Control" settings are both set
to "On".
Speaker Levels
• Refer to the connected compoueut's
details.
to an input source.
instruction manual for
You can adjust the volume
These
Alter changing
"Audio Return
the settings of the "HDMI Control",
Ch", "Power Control", or "TV Con-
trol", turn off the power
equipment
User's
to all connected
pieces
and then turn them on again. Refer
Manuals
for all connected
pieces
of
to the
receiver
temporary
adjustments
is set to Standby.
here, go to "Level
of each speaker
while listening
are cancelled
when the AV
To save the setting
Cal (Level Calibration)"
setting the AV receiver
you made
(_
36) before
to Standby.
N Subwoofer
of equipment.
-15 dB to 0 dB to +12 dB in 1 dB steps
N Center
-12 dB to 0 dB to +12 dB in 1 dB steps
!
• You cannot use this fuuctiou while the AV receiver is muted.
• Speakers that are set to "No" or "None" in the "Sp Coufig
(Speaker Configuration)" (_ 35) cannot be adjusted.
Erl
41
ii
Audyssey Settings
CinemaFILTER
m Dynamic EQ
With the CinemaFILTER, you can soften overly bright
movie soundtracks, which are typically mixed for reproduction in a movie theater.
m Dyn Vol (Dynamic Volume)
See "Dynamic EQ" and "Dynamic Volume" of "Audio
Adjust" (_ 3"/).
Late Night Function
With the Late Night function, you can reduce the dynamic
range of Dolby Digital material so that you can still hear
quiet parts even when listening at low volume levels-ideal for watching movies late at night when you don't
want to disturb anyone.
CinemaFILTER can be used with the following listening
modes: Dolby Digital, Dolby Digital EX, Dolby Digital
Plus, TrueHD, Dolby Pro Logic IIx Movie, Dolby Pro
Logic II Movie, Dolby Pro Logic IIz Height, Multichannel, DTS, DTS-ES, DTS Neo:6 Cinema, DTS 96124,
Neo:6, DTS-HD High Resolution, DTS-HD Master and
DTS Express.
ff Cinema
Fltr
+ Off:
CinemaFILTER
m Late
Night
For Dolby
options
off.
+ On:
Digital
and Dolby
Digital
Plus sources,
the
CinemaFILTER
on.
are:
+ Off:
Late Night function
• The CinemaFILTER
sources.
off.
Low:
Small reduction
in dynamic
range.
in dynamic
range.
For Dolby
TrueHD
sources,
the options
are:
ff AudioSel
The
Late
Night/unction
is set to "On"
or "OFF'
+ ARC:
automatically.
Off:
Late
Night
l'unction
off.
+ ()n:
Night
Late
t'unction
on.
The
audio
signal
the
NDMI
OUT
With
this
cally
selected
• The effect
of the Late Night
that you are playing
designer,
and with
you
select
• The Late Night
set to Standby.
"Auto".
some material
function
Digital,
• The Late Night
function
depends
and the intention
the different
there
will be little or no effect
Plus,
or Dolby
TrueHD
when
sources,
the input source
This
the AV receiver
is
cal
En
42
is stored
• The M.Opt
indicator
assigned,
have
assignments.
NDMI
IN has
been
HDMI
(NDMI
HDMI
input
is auto-
as a priority.
COAXIAL IN has
when
source.
been
If both
assigned,
coaxial
coaxial
been
and
input
opti-
is auto-
as a priority.
function
only works
The Music
mode
with
PCM digital
rate below' 48 kHz and anaOptimizer
is disabled
individually
will light (_
when
for each input
8).
selector.
IN has
been
source.
input,
individually
can be made
(HDMI
for each input
only for the input
IN) and digital
IN) are assigned,
by setting
see "Digital
"1 You can select
Ch"
to "ARC"
Audio
"ARC"
But you cannot
Return
is selected.
OPTICAL
as HDMI IN, COAXIAL
HDM[
with a sampling
when
as an input
is stored
setting
priority
• The setting
be automati-
The AV receiver always outputs analog signals.
OPTICAL
signals.
can
other
(COAXIAL IN or OPTI-
been
selected
assigned
• This
Music Optimizer on.
listening
to
+ Analog:
assigned
log audio input
be sent
among
If both
inputs
can be selected
• The setting
+ On:
the Direct
can
OPT:
ff M.Optimizer
+ Off:
Music Optimizer off.
signals
audio
audio
as an input
inputs
This
Optimizer
TV's
source.
can be selected
assigned
it will be set to
The Music Optimizer function enhances the sound quality
of compressed music files. Use it with music files that use
"lossy" compression, such as MP3.
input
tuner
+ COAX:
TrueHD.
Music Optimizer
audio
TV
when
selected
matically
• The Music
the
as an input
matically
is set to "Off"
For Dolby
your
as a priority
IN) and digital
CAL IN) have
sound
options.
Digital
function
selection
can be selected
assigned
on the material
of the original
can be used only when
Dolby
from
of the AV receiver.*1
HDMI:
This
is Dolby
input
You can set priorities of audio output when there are both
digital and analog inputs.
Auto:
when
used with certain
Audio Selector
High:
Large reduction
may not work when
select
setting
audio
(Digital
inputs
40).
is
IN. If both
(COAXIAL
IN or
input will be selected
40).
To select
Audio
the digital
Input)"
if you select the TWCD
it if you've
(_
that
IN, or OPTICAL
HDM[
(_
selector.
source
selected
"Off"
(_
as a
audio
34).
input selector.
in the "Audio
A/V Sync
When
using progressive
scanning
on your Blu-ray
DVD player, you may find that the picture
out of sync. With this setting,
delaying
Disc/
and sound
you can correct
are
this by
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
the audio signals.
Press
select
N A/V Sync
_0 ms to 100 ms in 10 ms steps
TONE on the AV receiver
either "Bass" or "Treble".
repeatedly
Use TONE -/+ on the AV receiver
to
to adjust.
!
• A/V Sync is disabled when the Direct listening mode is used
with all analog input source.
• The setting is stored individually for each input selector.
N Bass
N Treble
See "Bass"
(_
The digital
input signal formats
input sources
(_
are available
that you have assigned
only for the
a digital
input jack
34).
Normally,
the AV receiver detects the signal format
matically.
However,
if you experience
either
auto-
and "Treble"
of "Tone Control
Settings"
41 ).
• To bypass the bass and treble tone circuits, select the Direct listening mode.
• This procedure can also be performed on the remote controller
by using AUDIO (_ 41).
of the tZ)llow-
ing issues
when playing PCM or DTS material,
manually
set the signal format
you can
to PCM or DTS.
• If the beginnings of tracks h'om a PCM source are cut off, try
setting the format to PCM.
• If noise is produced when fast forwarding or reversing a DTS
CD, try setting the format to DTS.
• The setting is stored individually for each input selector.
• The setting will be reset to "Auto" when you change the setting
in the "Audio Selector" (_ 42).
Press RECEIVER,
and then press
AUDIO for about 8 seconds.
While "Auto"
to select:
i
and hold
lights (about 3 seconds),
press
-ql/_
Auto:
The format
is detected
automatically.
If no dig-
ital input signal is present, the corresponding
analog
input is used instead.
PCM:
Only
2-channel
PCM format
input signals
be heard. If the input signal is not PCM,
PCM indicator
will
the
will flash and noise may also be
produced.
DTS:
Only DTS (but not DTS-HD)
format
input sig-
nals will be heard. If the input signal is not
DTS, the DTS indicator will flash and there
will be no sound.
En
43
ii
Zone 2
In addition to your main listening room, you can also enjoy playback
can select a different source for each room.
in the other room,
or as we call Zone 2. And, you
Connecting Your Zone 2 Speakers to an
Amp in Zone 2
There are two ways you can connect
Zone
1.
Connect
them directly
2.
Connect
them to an amp in Zone 2.
2 speakers:
This setup allows 7.1-channel
to the AV receiver.
playback
in your main lis-
tening room and 2-channel stereo playback
with a different source in each room.
in Zone 2,
Connecting Your Zone 2 Speakers Directly
to the AV receiver
This setup allows
5.1-channel
playback
in your main room
and 2-channel stereo playback in Zone 2, with a different
source in each room. This is called Powered Zone 2, as the
Zone 2 speakers
when Powered
channel
are powered
Zone
playback
by the AV receiver.
2 is turned
in your main
Note that
off, you can enjoy 7.1room.
Main room
5
_
Zono2
int eRg;C
tlde;/m P
--_
• The Zone 2 volume must be set on the Zone 2 amp.
Zone 2
R
L
• With this setup, the Zone 2 volume is controlled by the AV
receiver.
En
44
If you've connected your Zone 2 speakers to the AV
receiver, as explained in "Connecting Your Zone 2 Speakers Directly to the AV receiver" (_ 44), you must set the
"Front HiglffZone2" setting to "Zone2".
i
This section explains how to turn Zone 2 on and off, how
to select an input source for Zone 2, and how to adjust the
volume for Zone 2.
Controlling Zone 2 from the AV receiver
Press RECEIVER followed by SETUP.
The setup menu appears.
Use A/¥ to select "Hardware",
ENTER.
Use 1/¥
to select
to select
"Zone2".
"Front
ZONE2
FRONT
HIGH
activated
High/Zone2",
and
m/_
............
OR ZONE2
(Powered
-/+
and then press
Zone2:
minals
OFF
L/R speaker
,z,
=======================
z z z z]
ter-
Zone 2 enabled).
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!
_J
ZONE 2 indicator
• When "Zone2" is selected and Zone 2 turned on, the Zone 2
speakers connected to the FRONT HIGH OR ZONE2 L/R
speaker terminals output sound, but the surround back or front
high speakers connected to the SURR BACK OR FRONT
HIGH L/R speaker terminals do not. When "Zone2" is selected
and Zone 2 turned off, the surround back or front high speakers
output sound as normal.
• When the "Front High/Zone2" setting is set to "Zone2" and the
input selector of Zone 2 is selected, power consumption on
standby mode slightly increases.
Input selector buttons
To turn on Zone 2 and select an input source, press
ZONE 2 on the AV receiver followed by an input
selector button within 8 seconds.
Zone 2 turns on, the ZONE 2 indicator lights.
To select AM or FM press the TUNER input selector
button repeatedly.
To select
the same source
press ZONE
Source"
2 repeatedly
appears
as that of the main room,
until "Z2 Selector:
on the display.
• You cannot select different AM or FM radio stations for
your main room and Zone 2. The same FM/AM radio station will be heard in each room.
To turn off Zone 2, press
OFF
on the AV receiver.
• While Powered Zone 2 is being used, listening modes that
require surround back and front high speakers (6.117.1), such as
Dolby Pro Logic IIz Height, Dolby Digital EX, and DTS-ES are
unavailable.
• When the "Front High/Zone2" setting is set to "Zone2" and the
input selector of Zone 2 is selected, power consumption on
standby mode slightly increases.
EF1
45
Controlling Zone 2 with the Remote
Controller
Adjusting the Volume for Zone 2
m Operating
..............
_
ON/STANDBY
ZONE2
......
_
_._i!
...........
'. _,,'
--INPUT
G-
with the remote
Press ZONE2.
SELECTOR
Use VOL l/V
Press
ZONE2,
and then press
Zone 2 turns on, the ZONE
To select
ZONE2,
an input
followed
to adjust
the volume.
--MUTING
m Operating
Press
controller
ZONE
2 (the ZONE
selector
on the display
Use -/+
within
2 indicator
and Zone
2
flashes).
8 seconds
to adjust
the volume.
ON/STANDBY.
2 indicator
lights.
source for Zone 2, press
by an INPUT SELECTOR.
To select AM or FM press the
on the AV receiver
TUNER input
If your Zone 2 speakers are connected to a receiver or integrated amp in Zone 2, use its volume control to adjust the
volume.
selector
repeatedly.
• You cannot select different AM or FM radio stations for
your main room and Zone 2. The same FM/AM radio station will be heard in each room.
Muting Zones
m Operating
Press
with the remote
ZON E2 followed
controller
by MUTING.
To turn off Zone 2, press ZONE2 followed by ON/
STANDBY.
iii
• To unmute,
• Press ZONE2 followed by MUTING again.
i
• To control Zone 2, you must press the remote controller's
ZONE2 first.
• Only analog input sources are output by the ZONE 2 MNE
OUT and FRONT HIGH OR ZONE2 L/R speaker terminals.
Digital input sources are not output. If no sound is heard when
an input source is selected, check if it's connected to an analog
input.
• While Powered Zone 2 is being used, listening modes that
require surround back and front high speakers (6.117.1), such as
Dolby Pro Logic IIz Height, Dolby Digital EX, and DTS-ES are
unavailable.
• While Zone 2 is on, RI functions will not work.
• You cannot select different AM or FM radio stations for your
main room and Zone 2. The same FM/AM radio station will be
heard in each room. For example, if you have an FM station for
the main room, that station will also be used in Zone 2.
• Zones can also be unmuted by adjusting the volume.
En
46
Controlling iPod
"1
No.
Onkyo Dock
Cable
%
UP-A 1 Dock (Included)
Universal Port Option Dock)
--
Note
When
Page
UP-AI
connected,
standby
Dock
the power
mode slightly
You can control
"PORT"
%
RI Dock
(Not included)
Analog
audio
your
is selected
See the R[ Dock's
(RCA)
that
seated
iPod is
consumption
(÷ 48)
on
increases,
iPod when
as the input source.
instruction
manual
(o 49)
for more information.
To use 1"41 (Remote
Component
video
you
and the R[ Dock.
Y
Composite
[nteractive),
must make an analog audio connection (RCA) between
the AV receiver
video
I'-ql cable
"1
Models
sold are different
depending
on the region.
En
47
• Do not take offyour
music,
• Don't
photo,
iPod fi'om the Dock when
or movie
use the UP-AI
FM transmitters
malfunction.
stored
on your
with any other
and microphones,
• It is recommended
that you update
able at the Apple
iPod accessories,
because
your
using it with this unit. The updater
you play back the
iPod.
such as
they may cause
iPod software
a
before
for the iPod software
is avail-
website.
N Basic Operation
UP-A1 Dock
The AV receiver
With the supplied
music, photo,
UP-AI
or movie
the AV receiver
Dock,
you can easily
play the
stored on your Apple iPod through
and enjoy great sound.
You can use the AV receiver's
remote
to operate
your iPod.
Made
Power
iPod
Direct
will automatically
If you start iPod playback
• iPod
(2nd generation)
source, the AV receiver
basic iPod functions
• iPod (4th generation)
• iPod nano
(3rd generation)
• iPod nano
(2nd generation)
• iPod nano
• iPod mini
(lst generation)
• Functionality
• Before
1.
to prevent
source
2.
iPod in the Dock
Turn on the AV receiver,
the PORT
Remove case
before inserting
and select
and carefully
(North
American
needs
to be adjusted
gap between
the adapter,
gap. Turning
the adapter
ward. Turning
it clockwise
counterclockwise
counterclockwise
moves
are connected
to select
PORT
iPod in the UP-AI
a
the back of your iPod and
turn the adapter
selecting
and generation.
stop iPod playback
the iPod input
UP-AI
to your iPod, the AV receiver
the input
Dock
source
properly.
to the radio
models)/UP-DTl
tuner UP-HTI
(Asian
models)
with
repeatedly
on the front panel.
Dock,
make
sure
it's not set too high before
you reconnect
your headphones.
• The Auto Power On function will not work if you set your
to
iPod. If there's
from
source,
• While your iPod is in the UP-A 1 Dock, its volume control has
no effect. If you adjust your iPod models volume control while
the Adapter
match your particular
iPod model
input
selected by the tuner's Mode Selector switch, you can
the input source between
UP-A 1 Dock and the tuner,
it's in the UP-AI
The adapter
on your
a different
the AV receiver
connecting
by pressing
place your
iPod in the slot, as shown.
N Adjusting
to control
49).
by mistake.
• When
AUTO
switch
selector.
Align your iPod with the Dock
connector,
(_
depends
selecting
• If any accessories
Your
input
select your iPod
N Operating Notes
may not be able
N Putting
to another
Using the AV receiver's
Remote Controller
You can use the AV receiver's remote controller
• iPod (5th generation)
(4th generation)
while listening
will automatically
as the input source.
• iPod touch (lst generation)
• iPod classic
(5th generation)
is on
turn on and
Change
models
• iPod nano
while the AV receiver
the AV receiver
• All iPhone
• iPod nano
so
select your iPod as the input source.
models
for:
touch
to startup,
of the first
On
If you start iPod playback
Standby,
N Compatible
seconds
song.
Auto
controller
may take several
you might not hear the first few seconds
to close the
moves it for-
it backward.
Forward
• When
Direct
Dock
while
it is playing.
Zone 2 is turned on, you can't use Auto
Change functions.
Power
On and
N Using Your iPod models Alarm Clock
You can use your iPod models Alarm Clock function to
automatically turn on your iPod and the AV receiver at a
specified time. The AV receiver's input source will automatically be set to the PORT selector.
Backward
• To use this function, your iPod must be in the UP-AI
Dock,
the UP-AI Dock must be connected
to the AV receiver.
• Make
sure
that the output
level of the AV receiver
is set to mini-
mum.
• To prevent damage to the dock connector,
don't twist your
when inserting or removing
it, and be careful not to knock
ER
48
the dock
while your
iPod is inserted.
iPod
over
and
• This function
only works when the Standard mode is set to On.
• When you use this function, be sure to set the AV receiver's
volume control to a suitable level.
• When Zone 2 is turned on, you can't use this function.
• You cannot use this function for sound effects on your
iPod.
m Charging
The UP-AI
Your iPod models
Dock charges
your iPod is in the UP-A1
UNIVERSAL
PORT
iPod is seated
charged
Battery
Direct
your iPod models
battery
Dock and connected
to the
jack on the AV receiver.
in the UP-AI
Dock,
when the AV receiver
while
While your
its battery
will be
Change
If you start iPod playback
source, the AV receiver
Remote
m Status
• PORT
Messages
Reading
• PORT
is checking
the connection
The AV receiver
functionality
iPod
do not support
the connected
dock.
Dock is connected.
function
will turn on at the specified
the AV receiver
iPod slideshows
the onscreen
view, navigate,
display
(OSD)
remote
trol your iPod from the comfort
use the AV receiver's
iPod.
remote
and enjoy
great
and videos on your TV.
and select your iPod's
TV, and with the supplied
allows you to
contents
controller,
on your
you can con-
of your sofa. You can even
controller
to operate
your
• Enter the appropriate remote control code before using the AV
receiver's remote controller for the first time (_ 51 ).
• Connect the R[ Dock to the AV receiver with an f'-41cable
(÷ 47).
• Set the RI Dock's R[ MODE switch to "HDD" or "HDD/
DOCK".
• Set the AV receiver's [nput Display to "DOCK"
System
Function
I
Operating
Notes
• Use the AV receiver's volume control to adjust the playback
volume.
• While your iPod is inserted in the R[ Dock, its volume control
has no effect.
By pressing REMOTE MODE that's been programmed
with the remote control code for your Dock, you can control your iPod in the Dock with the following buttons.
See "Remote Control Codes for Onkyo Components Connected via ["4I" for details on entering a remote control
code (_ 51 ).
See the Dock's instruction manual for more information.
I UP-A1 Dock
PORT is preprogrammed with the remote control code for
controlling a Dock with Universal Port connector.
You can control your iPod when "PORT" is selected as
the input source.
Without the RI Control
You must enter a remote
I
control
code 82990
first (_
51 ).
RI Dock
• Set the RI Dock's
• ON/STANDBY
In addition,
iPod are on, the AV receiver
ON/STANDBY.
Power
iPod playback
RI MODE
switch
to "HDD"
or
"HDD/DOCK".
you turn on the AV receiver,
turn on automatically.
Auto
(_ 23).
in
When
time and
automatically.
alarm is set to play a sound.
• ff you use your iPod with any other accessories,
detection may not work.
for several sec-
you can easily play the music stored on
iPod through
and watch
System
on your iPod to start play-
• [f you do adjust the volume control on your iPod while it's
inserted in the RI Dock, be careful that it's not set too loud
before you reconnect your earphones.
With the RI Dock,
I
on the AV receiver.
Alarm
back, the AV receiver
RI Dock
In addition,
depends
with the AV
The available
If you use the Alarm
onds after recognizing the UP-A 1.
• When the status message is not displayed on the AV receiver's
display, check the connection to your iPod.
sound,
that came
• This function only works when the Standard mode is set to On.
• The AV receiver displays the message "UP-AI"
your Apple
controller
other iPod functions.
• Linked operations do not work with video playback or when the
UP-A1
UP-AI
to the
with the
Not Support
• PORT
to control
select your iPod as the input source
The AV receiver
dock.
switch
Controllers
You can use the remote
receiver
• When UP-AI Dock that seated iPod is connected, the power
consumption on standby mode slightly increases.
to another input
input to which the RI Dock is connected.
Other
is set to "On" or "Standby".
while listening
will automatically
the RI Dock and iPod
when the RI Dock and
can be turned
code (without
and enter
may not work with a remote
control
R I). In this case, make an [41 connection
a remote
control
code 81993
(with
R I).
on by pressing
With the RI Control
in
If you press the remote
controller's
receiver
the AV receiver
is on Standby,
_
while the AV
will automatically
turn on, select your iPod as the input source,
and your
In this case, make an [-4! connection and enter a remote
control code 81993 (with [-4I).
• Set the AV receiver's Input Display to "DOCK" (_ 23).
iPod will start playback.
EFI
49
_: Available
MODE
first,appropriate
Press the
REMOTE
buttons
1
o
o
a
@
®
®
ON/STANDBY
o
o
V'*I
t/O
TOP MENU
il!l41_
,,'*5
v"
ENTER
i/'3
v"
,/
v"
PLAY MODE
i/'4
i/'4
DISPLAY*6
i/'2
PLAYLIST _/_
@
I_, I I, II, <<,
I_i,,-I
i_i,_, I<<,
REPEAT
RANDOM
®
®
®
®
• With
some
iPod models,
• For detailed
operation
"1 This button
button,
does
in which
generations
of the iPod,
and R[ Docks,
please
not turn the Onkyo
case you should
DS-A2
press
This is because
the remote controller
remain on when the remote controller
Similarly,
if your
iPod is already
*2 Press DISPLAY to change
Standard
mode
Nothing
is displayed
oil your
Playlists
your
(artists,
albums,
mode
transmits
transmits
@
MENU
@
iRETURN
may not work as expected.
manual
R[ Dock
of RI Dock.
oil or off. Your iPod may not respond
the On and Standby
an On command.
off, it will remain
the first time
you press this
off when
commands
the remote
alternately,
controller
so if your
transmits
iPod is already
oil, it will
an Off command.
modes:
TV and you navigate
and select
your contents
by using your
iPod models
display.
the video.
songs,
and so oil) are displayed
(see "2), PLAYLIST
With the page modes,
*4 Resume mode
With the Resume
is used
you can quickly
function,
locate
you call restune
changed the OSD mode to Off.
*5 TOP MENU works as a Mode button
En
or DS-A2X
VOL lit
oil your TV, and you can navigate
and select
your
music
while
looking
at
TV.
*3 [n Extended
5O
buttons
ALBUM +/-
it again.
the following
Only this mode can playback
Extended
mode
certain
refer to the instruction
MUTING
when
*6 DISPLAY
turns oil backlight
• [n Extended
mode
(see *2), the playback
• [n Extended
mode
(see *2), you cannot
• [n Extended
mode
(see *2), it may take some
• [n Extended
mode
(see "2), video contents
as the page jump
your favorite
playback
songs
button.
even when
your
of the song that was playing
used with
a DS-A2
song lists, artist
when
you removed
R[ Dock.
for 30 seconds.
will be continued
operate
your
even if the AV receiver
iPod directly.
time to acquire
can not display
the contents.
oil your TV.
is turned
off.
lists, and so oil are very long.
your
iPod from the R[ Dock
or
Controlling Other Components
You can use the AV receiver's remote controller
(RC-764M) to control your other AV components. This
section explains how to enter the remote control code
(with the default underlined) for a component that you
want to control: DVD, TV, CD, etc.
Onkyo
components
trolled
by pointing
receiver,
not the component.
components
The following REMOTE MODE are preprogrammed
with remote control codes for controlling the components
listed. You do not need to enter a remote control code to
control these components.
For details on controlling these components, see the pages
indicated.
that are connected
the remote
via r41 are con-
controller
at the AV
This allows you to control
that are out of view, in a rack, for example.
Make
sure
the Onkyo
with an f:_ I cable
component
and an analog
is connected
audio
cable
(RCA).
See "Connecting
details (_ 18).
Enter
Onkyo
f'41 Components"
the appropriate
remote
control
for
code for
REMOTE MODE.
• BD/DVD
BD/DVD Onkyo Blu-ray Disc player (_ 52)
TWCD
Onkyo CD player (_ 52)
PORT
Onkyo Universal Port Option (_ 49)
31612:
Onkyo
• TV/CD
DVD player
with f'4 I
71327:
You'll need to enter a code for each component that you
want to control.
Look
up
the appropriate
remote
control
code in
Onkyo
CD player
with RI
42157:
Onkyo
• PORT
cassette
tape deck with R I
_81993:
I:!_ the separate
Remote Control Codes list.
....................................
The codes are organized by category (e.g., DVD
_
player,
TV_ etc.). down REMOTE
While holding
MODE
to which
you want to enter a code, press and hold down
DISPLAY until the remote indicator
lights (about
Dock
section
for how to enter remote
3 seconds).
• When using a cassette tape deck connected via RI, press
and hold TWCD to switch to TAPE.
!
Press
• Remote control codes cannot be entered for RECEIVER
and ZONE 2.
• Only TV remote control codes call be entered for TV.
• Apart from RECEIVER, TV, and ZONE 2, remote control codes from any category can be entered for REMOTE
MODE. However, these buttons also work as input selector buttons (_ 22), so choose a REMOTE MODE that
corresponds with the input to which you connect your
component. For example, if you connect your CD player
to the CD input, choose TV/CD when entering its remote
_
Onkyo
See the previous
control codes.
control 30
code.
Within
seconds,
use the number
buttons
to
enter the 5-digit remote control code.
The remote indicator flashes twice.
If the remote
control
fully, the remote
code is not entered
indicator
success-
REMOTE
MODE,
ler at the AV receiver,
point the remote
and operate
control-
the component.
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that's not connected via f-4I, use the
following remote control codes:
• BD/DVD
30627:
Onkyo DVD player without f:_I
• TWCD
71817:
Onkyo CD player without R I
11807:
Onkyo TV
will flash once slowly.
En
51
If you want to control
remote
control
controller
codes:
an Onkyo component
directly
by pointing
at it, use the following
the
remote
By pressing REMOTE MODE that's been programmed
with the remote control code for your component, you can
control your component as below.
For details on entering a remote control code for a different component (_ 51 ).
32900:
Onkyo
Blu-ray
Disc player
32901:
Onkyo
HD-DVD
player
70868:
Onkyo
71323:
MD recorder
Onkyo
82990:
CD recorder
Onkyo
Controlling a Blu-ray Disc/DVD Player, HD
DVD Player or DVD Recorder
BD/DVD
is preprogrammed
for controlling
Dock
a component
with the remote
that supports
control
The component
must be able to receive remote control
commands
via f-'4Jl-lD and be connected
to the AV
• If you connect an cassette tape deck to the TV/CD IN jack, or
connect all R[ Dock to the TWCD IN or VCR/DVR IN or
GAME INjacks, for 1"-41to work properly, you must set the Input
Display accordingly (_ 23).
You can reset a REMOTE MODE to its default remote
control code.
While
want
holding
down
REMOTE
MODE
that you
to reset, press and hold down AUDIO
the remote
Within
indicator
30 seconds,
lights
press
(about
REMOTE
The remote indicator flashes
the button has been reset.
twice,
MODE
indicating
remote control code. When a button is reset,
Each of REMOTE MODE is preprogrammed
....................................
programmed
code is restored.
=
"
"
O
"
=
You can reset the remote
"
•
"
controller
•
until
3 seconds).
•
again.
that
its prewith a
"
to its default
settings.
While holding down RECEIVER, press and hold
down AUDIO until the remote indicator lights
(about 3 seconds).
Within 30 seconds, press RECEIVER again.
The remote indicator flashes twice, indicating that
the remote controller has been reset.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
En
52
receiver
via HDMI.
code
the I-'4AI-ID.
_: Available
buttons
I
O
=.
>=.l
IS--2
Buttons
"\
>
o._>
,-, I _,.t
" in" _
._ I_=,-,i>o
_-'=
,-,,-, o
ON/STANDBY
i t/¢
_
t/_, INPUT,
TV VOL A/V
GUIDE
TOP MENU
PREV CHINEN!
I
GUIDEITOP MENU
@ ilVl_lli,_
ENTER
SETUP
-,I1_1,I_1_,
I
I_1_1,
I_l_l
SEARCH
REPEAT
RANDOM
trl *_
i/'1"2
i/*1"_
f,,/:l
_
_-_
PLAY MODE
@ Number:
to9,0
Number: +10
@ DISPLAY
_
© @
® ® ®
®
__
MUTING
@ CH +/DISC +/@ PREV CH
MENU
@
!TL_:Us ;>
_
RETURN
AUDIO
_
CLR
"1 The r411-ll_ function is not supported. The r411-ll_ supported by the AV receiver is the CEC system control function
of the HDM[ standard.
*2 These buttons functions as colored buttons or A, B, C, D buttolls.
I;_C+7_i4
*3 ||
--_.
__
(Pause) functions as reverse playback.
j
• See the "Controlling
(_ 49).
Your iPod" about the operation of iPod
• With some components, certain buttons may not wrork as
expected, and some may not work at all.
En
53
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can't resolve the issue yourself, contact your Onkyo dealer.
If you can't
resolve
AV receiver
before
the issue yourself,
contacting
try resetting
the
your Onkyo dealer.
m The STANDBY indicator flashes
red
The protection
circuit has been activated. Remove
the power cord from the wall outlet immediately.
Disconnect
all speaker cables and input sources, and
leave the AV receiver with its power cord disconnected for 1 hour. After
cord and set the volume
that, reconnect
to maximum.
the power
If the AV
To reset tile AV receiver to its factory defaults, turn it
on and, while holding down VCB/DVB, press ON/
receiver
connect
STAN DBY. "Clear"
and input sources. If the AV receiver turns off when
you set the volume to maximum,
disconnect
the
the AV receiver
will appear
on the display
will enter Standby
and
mode.
power
VCR/DVR
I/o
oN,s
stays on, set the volume to minimum,
disthe power cord, and reconnect
your speakers
cord, and contact
your Onkyo
dealer.
FAN£BY
_rtt_/t;l
N There's no sound, or it's very quiet
Note that resetting the AV receiver will delete your
radio presets and custom settings.
Make sure
properly.
that tile digital
input source
34
is selected
Remote indicator
Make sure that the inputs and outputs
nents are connected
properly.
RECEIVER
Make
Check
AUDIO
To reset the remote controller to its factory defaults,
while holding down RECEIVER, press and hold down
AUDIO until the remote indicator lights (about 3 seconds). Within 30 seconds, press RECEIVER
again.
sure
that the input
the volume.
source
is properly
The AV receiver
selected.
is designed
home theater enjoyment.
It has a wide volume
allowing
precise adjustment.
16-18
22
for
range,
If there's no sound from a DVD player connected
to
an HDM[ IN, check the DVD player's output settings, and be sure to select
With
audio
some DVD-Video
output
format
a supported
discs,
audio format.
you need to select an
from a menu.
Make sure that none of the connecting
bent, twisted, or damaged.
r_
of all compo-
cables
are
Specify the speaker distances and adjust the individual speaker levels.
36
The input signal
to Auto.
43
N Can't turn on the AV receiver
Make sure that tile pow'er cord is properly
into the wall outlet.
plugged
format
is set to PCM
or DTS.
Set it
N Only the front speakers produce sound
When the Stereo or Mono listening mode is selected,
only the front speakers and subwoofer
produce
sound.
@
ED
54
--
N Noise can be heard
m Only the center speaker produces sound
ffyou
use the Dolby
Logic
tening
IIx Music, or Dolby Pro Logic [Ix Game lismode with a mono source, such as all AM
Pro Logic
IIx Movie,
radio station or mono TV program,
centrated
in the center speaker.
Dolby
the sound
Pro
--
Using
cable
ties to bundle
audio cables
with
power
cords, speaker cables, and so on may degrade
audio performance,
so don't do it.
the
is con-
N The Late Night function doesn't work
N The surround speakers produce no sound
When
the T-D (Theater-Dimensional),
Mono listening
mode is selected,
speakers produce no sound.
Stereo
Make sure the source material
Dolby Digital Plus, and Dolby
o1"
is Dolby
TrueHD.
42
Digital,
the surround
N About DTS signals
When
DTS program
material
ends
and the DTS bit-
stream stops, the AV receiver remains
in DTS listening mode and the DTS indicator
remains on. This is
Make
sure the speakers
are configured
correctly.
35
N The center speaker produces no sound
When
the Stereo
the center
or Mono
speaker
listening
produces
mode is selected,
--
no sound.
to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you
switch your player from DTS to PCM, because the
AV receiver does not switch formats immediately,
you may not hear any sound, in which case you
should stop your player for about three seconds,
then resume
N The front high or surround back speakers
produce no sound
rl
Depending
on the current listening mode, no sound
may be produced
by the front high or surround back
ut
31.
d_
tt
n_
N
speakers.
Select
another
listening
sure the speakers
29
mode.
are configured
correctly.
35
you play source
information
in the LFE
duces no sound.
material
that contains
channel,
playing
DTS program
pause, fast forward,
player may produce
a malfunction.
material,
or fast reverse
a short audible
using
the
function on your
noise. This is not
N The beginning of audio received by an HDMI IN
can't be heard
N The subwoofer produces no sound
When
N
LI
When
Make
and
playback.
no
the subwoofer
Since it takes longer to identify the format of an
HDM[ signal than it does for other digital audio sig-
pro-
nals, audio
output
may not start immediately.
Lvitgl'Z'_l_
N There's no sound with a certain signal format
Check
the digital
audio output
setting
N There's no picture
on the con-
nected device. On some game consoles,
such as
those that support DVD, the default setting is off.
Depending
on the input signal,
cannot be selected.
some listening
modes
Make sure that all video connecting
in all the way.
29-32
back
speakers
or front high
are connected,
or the Zone 2 speakers
used, 6.1/7.1 playback
is not possible.
ff the video source is connected
to a component
video input, you must assign that input to an input
selector, and your TV must be connected
PONENT
VIDEO
MONITOR
OUT.
N Can't get 6.1/7.1 playback
If no surround
plugs are pushed
15
17, 34
to COM-
speakers
are being
If the video
source
is connected
to an HDM[
input,
16, 34
you must assign that input to an input selector, and
your TV must be connected
to the HDM[ OUT.
N The volume cannot be set to 79
Check
to see if a maximum
volume
has been set.
22
Erl
55
mThere's no picture from a source connected to
an HDMI IN
Reliable operation with all HDMI-to-DVI adapter is
not guaranteed. Ill addition, video signals from a PC
are not guaranteed.
61
m The on-screen menus don't appear
On your TV, make sure that the video input to which
the AV receiver is connected
is selected.
If you've connected a cassette tape deck, to the TW
CD IN jack, or an RI Dock to the TV/CD IN or
GAME IN or VCR/DVR IN jacks, for the remote
controller to work properly, you must set the display.
23
To control
another
51
the remote
controller
To control
an Onkyo
manufacturer's
component,
point
at that component.
--
|O'/R_
N Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn't light
component
that's
not connected
51
via 1-41, point the remote controller
at the component. Be sure to enter the appropriate
remote control
code first.
Relocate your antenna.
I,/r/'4.'irir/"/t-dr/=l
Listen
to the station
24
in mono.
N There's no sound
Make
Passing
cars and airplanes
If nothing
antenna.
improves
can cause
the reception,
interference.
install
sure
your iPod is actually
playing.
--
an outdoor
--
Make sure the UP-A 1 Dock is connected to the UNI- -VERSAL
PORT jack on the AV receiver.
Make
the plugs are pushed
sure
in all the way.
N The remote controller doesn't work
Before
operating
this unit,
be sure to press
N There's no video
RECEIVER.
Install new batteries.
Don't mix different
batteries,
or old and new batteries.
types
Make
On.
sure
that your
Some
versions
iPod's
TV OUT setting
is set to
--
of
of the iPod do not output
video.
N The AV receiver's remote controller doesn't
control your iPod
Make
direct
sure that the AV receiver
sunshine or inverter-type
Relocate
sure
Make
you've
selected
entered
sure
your iPod is properly
inserted
in the
Dock. If your iPod is in a case, it may not connect
properly to the Dock. Always remove your iPod
from the case before inserting
it into the Dock.
if necessary.
Make sure you've
troller mode.
Make
code.
is not subjected
to
fluorescent
lights.
the correct
the correct
remote
remote
con-
control
10, 52
51
Make
sure
When
connecting
UP-HTI
you've
(North
selected
UP-AI
American
the right remote
Dock
to the radio tuner
models)/UP-DTl
(Asian models)
with AUTO selected by the tuner's
Mode Selector switch, you can switch the input
source between UP-AI
Dock and the tuner,
ing PORT repeatedly
on the front panel.
N Can't control other components
If it's an Onkyo
cable
and analog
Connecting
Ell
56
mode.
component,
audio cable
only an 1-41 cable
make
sure that the 1-41
are connected
won't
work.
properly.
18
Try resetting
your
iPod.
by press-
--
m The AV receiver unexpectedly selects your iPod
as the input source
Always
ferent
Direct
pause
iPod playback
before
selecting
a dif-
tings.
1. While holding down the input selector button for the input
source that you want to set, press SETUP.
2. Use -.41_ to change the setting.
3. Press the input selector button for the input source that you
want to set when you've finished.
• Video Attenuation
input source, ff playback
is not paused, the
Change function
may select your iPod as the
input source by mistake
between tracks.
m Can't
during
the transition
record
This setting can be made for the BD/DVD, VCR/DVR,
CBL/SAT, GAME, or AUX input.
If you have a games console connected to the composite
video input, and the picture isn't very clear, you can
attenuate the gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain is reduced by 2 dB.
On your recorder, make sure the correct input is
selected.
P_O/FLIN
m There's
N The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these set-
no sound
Only components connected to analog inputs can be -played in Zone 2.
The AV receiver
contains
a microcomputer
for signal
processing
and control functions. In very rare situations,
severe interference,
noise from an external source, or
static electricity
N The sound changes when I connect my
headphones
When
a pair of headphones
ing mode is set to Stereo,
Stereo, Mono, or Direct.
is connected,
unless
wall outlet,
N How do I change the language of a multiplex
source
N The 1-41functions
wait at least live seconds,
Adjust"
36
rental
make an RI
connection
and then plug it
and an
for damages
(such as CD
recordings
caused
by
the unit's malfunction.
Before you record important
data, make sure that the material will be recorded correctly.
Before
don't work
is not responsible
tees) due to unsuccessful
disconnecting
let, set the AV receiver
To use f-'_l, you must
In the unlikely
the power cord from the
set to
Onkyo
Use the "Multiplex"
setting on the "Audio
menu to select "Main"
or "Sub".
it to lockup.
unplug
back in again.
the listen-
it's already
may cause
event that this happens,
the power
cord from the wall out-
to Standby.
18
analog audio connection
(RCA) between the component and AV receiver,
even if they are connected
digitally.
N The functions Auto Power On/Standby and
Direct Change don't work for components
connected via 1-41
These
functions
don't
work
when
Zone
2 is turned
--
on,
En
57
Specifications
Amplifier Section
General
Rated Output Power
All channels:
Power Supply
(North American)
AC 120 V, 60 Hz
(Asian) AC 220 - 240 V, 50/60 Hz
Power
(North American)
(Asian) 500 W
(North American)
130 watts nlininmm
continuous
power
per channel, 6 ohm, at 1 kHz with a
maximum total harmonic
distortion of
1%
Consumption
Stand-by
Power
(Asian)
7 ch × 130 W at 6 ohms,
(IEC)
Maxinmm
Effective
Output
Power
(Asian)
7 ch × 160 W at 6 ohms,
(JEITA)
Dynamic
Power
Factor
Input Sensitivity
Level
Speaker
Ratio
Supported
1 kHz, 8 f2)
OUT
Video
Resolution
1080p
Audio
Fornmt
Dolby True HD, DTS Master Audio,
DVD-Audio,
DSD
3D, Audio Return Channel,
x.v.Color, LipSync, CEC
N Video Inputs
5 Hz - 100 kHz/+l
dB, -3 dB (DSP bypass)
106 dB (LINE, IHF-A)
(North American)
6 f_ - 16 f_
(Others)
4 f2 - 16 f2
Component
IN 1, IN 2
Composite
BD/DVD,
AUX
Level and Impedance
dB, -3 dB
Tuner Section
Component
OUT
Composite
MONITOR
Optical: 2
Coaxial: 2
Analog
BD/DVD, VCR/DVR,
TV/CD, AUX
Range
GAME,
VCR/DVR,
ZONE2 Line Out
Pre Output
Outputs
Phones
530 kHz - 1710 kHz
kHz - 1611/1710 kHz
Main (L, R, C, SL, SR, SBL, SBR)
+ ZONE2 / Front High (L, R)
l (6.3 o)
N Others
40
RI
Port
1
1
Specifications
and features
without notice.
[=[3
CBL/SAT,
1
Speaker
Universal
58
OUT
N Audio Outputs
Range
(North American)
(Others)
522/530
Channel
OUT, VCR/DVR
Digital
Analog
(North American)
87.5 MHz - 107.9 MHz
(Others)
87.5 MHz - 108.0 MHz, RDS
Preset
GAME,
N Video Outputs
Subwoof'er
Frequency
CBL/SAT,
Response
5 Hz - 100 MHz/+0
AM Tuning
VCR/DVR,
N Audio Inputs
Video Frequency
Frequency
Deep Color,
kf_ (REC OUT)
1 Vp-p/75 f_ (Component
Y)
0.7 Vp-p/75 f_ (Component
PB/CI3, PIJCI0
1 Vp-p/75 f_ (Composite)
FM Tuning
328.5 mm
× 12-15/16"
kf2 (LINE)
Video Section
Input Sensitivity/Output
151.5 mm×
IN 1, IN 2, IN 3, IN 4
60 (Front,
Characteristics
Impedance
Component
(North American)
8.6 kg (19.0 lbs.)
(Asian)
9.4 kg (20.7 lbs.)
and Impedance
Response
to Noise
Weight
Input
_+10 dB, 50 Hz (BASS)
_+10 dB, 20 kHz (TREBLE)
Signal
17-1/8" × 5-15/16"
Output
and Impedance
Tone Control
435 mm×
(W × H × D)
(North American)
0.08% (Power Rated)
(Asian)
0.08% (1 kHz, 1 W)
200 mV/2.2
Frequency
Dimensions
NHDMI
Distortion)
200 mV/47
Output
Consumption
0.2W
1 kHz, 1 ch driven
180 W (3 fZ Front)
160 W (4 fZ Front)
100 W (8 fZ Front)
THD (Total Harmonic
Damping
1 kHz, 1 ch driven
4.9 A
are subject
to change
N Center Speaker (SKC-580)
Type
2 Way Bass-reflex
m Subwoofer (SKW-580)
Impedance
Type
Maximum
Input
Bass-retlex
Sensitivity
sensitivity/Impedance
140 mV/20
kf_
Maximum
power
output
290 W (Dynamic
Frequency
response
25 Hz
Cabinet
power)
capacity
150 Hz
response
Crossover
frequency
65 Hz-50
2.8 L (0.10 cubic feet)
(W × H × D)
feet)
420 × 115 × 121 nun
(W x H x D)
(16-9/16"
317.5 × 463 × 398 mm
(12-1/2"×
18-1/4"×
(incl. projection)
15-11/16")
Weight
Drivers
10.7 kg (23.6 lbs.)
Audio Input
Drivers unit
1 (RCA analog mono)
Ternfinal
25 cm (10") Cone
Keyhole
Grille
(North American)
AC 120 V, 60 Hz
(Asian)
AC 220 - 240 V, 50/60 Hz
Power
supply
consumption
Other
(North American)
163 W
(Asian)
137 W
Auto Standby
function
2.4 kg (5.3 lbs.)
unit
2 Way Bass-reflex
Impedance
Maximum
2
Fixed
Other
Magnetic
N Surround/Surround
Frequency
response
55 Hz50
Crossover
frequency
capacity
Dimensions
Full-Range
Impedance
6f_
input power
Sensitivity
Cabinet
closed box
130 W
81 dB/W/m
response
80 Hz-20
capacity
kHz
1.0 L (0.036 cubic feet)
(W × H × D)
115×230×96mm
(4-1/2" × 9-1/16" × 3-3/4")
(incl. grille and projection)
kHz
4 kHz
5.7 L (0.20 cubic feet)
Weight
Drivers
(W × H × D)
1.0 kg (2.2 lbs.)
unit
8 cm (3-1/4")
155 × 375.5 × 170ram
Keyhole
(6-1/8" X 14-13/16" X 6-11/16")
(incl. grille and projection)
Grille
Cone
Spring type color coded
slot
1
Fixed
2.7 kg (6.0 lbs.)
unit
Terminal
Other
Back Speaker
Type
Ternfinal
Keyhole
Grille
shielding
(SKR-580/SKB-580)
Dimensions
130 W
85 dB/W/m
Weight
Drivers
× 2
dome (Tweeter)
6f2
input power
Sensitivity
Cabinet
Cone (Woofer)
Spring type color coded
slot
Frequency
Type
8 cm (3-1/4")
2.5 cm (1") Balanced
Maximum
N Front Speaker (SKF-580)
× 4-1/2" × 4-3/4")
(incl. grille and projection)
Weight
Power
kHz
6 kHz
capacity
Dimensions
38 L (1.34 cubic
130 W
86 dB/W/m
Frequency
Cabinet
Dimensions
6f_
input power
slot
12 cm (5") OMF Cone (Woofer)
2.5 cm (1") Balanced dome (Tweeter)
Spring type color coded
1
Dimensions
×D)
83×33×74mm
Fixed
Magnetic
(W×H
(3-1/4"×
shielding
Weight
1-5/16"×
2-15/16")
170 g (6 ounces)
Specifications
and features
without notice.
are subject
to change
EF1
59
About HDMI
Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital
interface standard for connecting TVs, projectors, Blu-ray Disc players/DVD players, set-top boxes, and other video
components. Until now, several separate video and audio cables have been required to connect AV components. With
HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM,
multichannel digital audio, and multichannel PCM).
The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)*1, so TVs and displays with
a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays,
resulting in no picture.)
The AV receiver uses HDCP (High-bandwidth Digital Content Protection)*2, so only HDCP-compatible components can
display the picture.
Audio Return Channel, 3D, x.v.Color, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution
I The
AVDolby
receiver's
HDMIDolby
interface
is based
theand
following:
Audio,
TrueHD,
Digital
Plus, on
DSD
Multichannel PCM
Supported Audio Formats
• 2-channel linear PCM (32-192 kHz, 16120124 bit)
• Multichannel linear PCM (up to 7.1 ch, 32-192 kHz, 16120124 bit)
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD
Master Audio)
Your Blu-ray Disc player/DVD player must also support HDMI output of the above audio formats.
About Copyright
Protection
The AV receiver supports HDCP (High-bandwidth Digital Content Protection)*2, a copy-protection
video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.
system for digital
"1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 ill 1999.
*2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by [ntel for HDM[/DVL It's
designed to protect video content and requires a HDCP-compatible device to display the encrypted video.
"3 DDWG (Digital Display Working Group): Lead by [ntel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this
open industry group's objective is to address the industry's requirements for a digital connectivity specification for high-performance
PCs and digital displays.
• The HDM[ video stream is compatible with DVI (Digital Visual [nterface), so TVs and displays with a DVI input can be connected by
using an HDM[-to-DVI adapter cable. (Note that DVI connections only carry video, so you'll need to make a separate connection for
audio.) However,reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.
• The HDM[ audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or
there's no sound from a component connected via HDM[, check its setup. Refer to the connected component's instruction manual for
details.
Ell
60
Using an RIHD-compatible TV, Player, or Recorder
1-411-ID, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo
components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over
HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than I-'411-lD-compatible components cannot be guaranteed.
m About _JHD-compatible
components
The following components are I-'411-lD-compatible. (As
of February 2010) See the Onkyo web site for latest informarion.
TV
• Panasonic VIERA Link compatible TV
• Toshiba REGZA-LINK compatible TV
• Sharp TV (See Onkyo web site for latest information on
compatible models.)
Players/Recorders
• Onkyo and Integra 1-411-lD-compatible players
• Panasonic VIERA Link compatible players and recorders (only when used together with Panasonic VIERA
Link compatible TV)
• Toshiba REGZA-LINK compatible players and recorders (only when used together with Toshiba REGZALINK compatible TV)
• Sharp players and recorders (only when used together
with Sharp TV)
Models
other than those
interoperability
HDM[
Standard,
• Do not connect
the following
linked
mentioned
if compatible
above
with CEC
but operation
cannot
operations
to the HDM[
work
is part of the
be guaranteed.
the f"-tll-IIO-compatible
number
component
input terminal
more
than
so that the
properly.
-Blu-ray
Disc/DVD
player
-Blu-ray
Disc recorder/DVD
is up to three.
recorder/Digital
Video Recorder
up to three.
-Cable/Satellite
• Do not connect
amplifier
• When
Set-top box is up to four.
the AV receiver to the other AV receiveffAV
For r_HD-compatible
TV
The following linked operation is possible by connecting
the AV receiver to an I-'411-lD-compatible TV.
• The AV receiver will enter Standby mode when the
power of the TV is turned to Standby.
• You can set on the menu screen of the TV to either output the audio from the speakers connected to the AV
receiver, or from the speakers of the TV.
• It is possible to output the video/audio from the antenna
or from the input jack of the TV from the speakers connected to the AV receiver. (A connection such as optical
digital cable or similar is required above the HDMI
cable.)
• Input to the AV receiver can be selected with the remote
controller of the TV.
• Operations such as volume adjustment or similar for the
AV receiver can be performed from the remote controller
of the TV.
may have some
which
N Operations that can be performed with _.JHD
connection
For r_l-ll_-compatible
players/recorders
The fonowing link operation is possible by connecting the
AV receiver to an r4lHD-compatihle
player/recorder.
• When the playback is started on the player/recorder,
input of the AV receiver win switch to the HDMI input
of the player/recorder that is playing back.
• Operation of the player/recorder is possible with the
remote controller supplied with the AV receiver.
is
Not all functions
may operate
depending
on the model.
via HDME
the f'411-11O-compatible
above-mentioned
is connected,
component
the linked
more than the
operations
are not
guaranteed.
En
61
N
m How to connect and setup
Confirm
1.
the connecting
Connect
and setting.
the HDMI OUT jack to the HDMI
input
Confirm
the settings.
1.
Turn on the power for all connected
2.
Turn off the power of the TV, and confirm
the power of the connected
jack of the TV.
off automatically
Blu-ray Oisc/OVO player, etc.
Turn on the power
4.
Start playback
• The power
HDMI
connection
@
5
_
@
HDMI
connection
5.
of the AV receiver
of the TV is turned
the audio output
OPTICAL
the operating
from the TV to the
using an
cable.
the HDMI
output
DVD player/recorder
of the Blu-ray
Disc/
to the HDMI I11 1 jack of
the AV receiver.
• It is necessary to assign the HDMI input when connecting
the Blu-ray Disc/DVD player/recorder to other jacks
(÷ 34). Do not assign the components connected to the
HDMI IN to the TV/CD input at this time. Appropriate
CEC (Consumer Electronics Control) operation can not be
guaranteed.
of the "HDMI
• HDMI
setup"
is changed
setting.
Control
(RIHD):
• Audio Return Ch (ARC):
• Power Control: On
• TV Control:
connected
is
of the TV,
6.
of the TV, and not from
connected
to the AV receiver.
Select "Use the speakers
receiver" from the menu
connected
from the AV
screen of the TV, and
confirm that the audio is output from the speakers connected
to the AV receiver, and not from
• When the audio return channel (ARC) function is used
with TV for HDM[ 1.4, it should not be this connection
lowing
on automat-
on automatically,
instructions
output from the speakers
III 2 jack of the AV receiver
optical digital
Each
is turned
select "Use the TV speakers" from the menu
screen of the TV, and confirm that the audio is
the speakers
(÷ 40).
3. Connect
and
the following.
Following
TV, projector, etc.
Connect
of the DVD player/recorder.
of the DVD player/recorder,
and input with the AV receiver
selected.
(OPTICAL)
2.
that
is turned
ically, and input with the DVD player/recorder
connected
is selected.
• The power
DIGITAL AUDIO
connection
components
with the link operation.
3.
confirm
components.
On
Auto
On
to the fol-
the TV speakers.
• Perform the abo ¥ "e operations when you initially use the
AV receiver, when the settings of each component are
changed, when the main power of each component is
turned off, when the power cable is disconnected from the
power supply, or when there has been a power outage.
Operate
with the remote
For buttons
controller.
that can be operated
(@ 59).
• Audio from DVD-Audio or Super Audio CD may not output from the TV speakers. You will be able to output the
audio from the TV speakers by setting the audio output of
the DVD player to 2ch PCM. (It may not be possible
depending on the player models.)
• Even if you set to output audio on the TV speakers, audio
will be output from the speakers connected to the AV
receiver when you adjust the volume or switch the input
on the AV receiver. To output audio from the TV speakers,
re-do the operations on the TV.
Do not connect the 1-41cable when connecting to the 1-41
See for details of each setting
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii,,,
(_
40).
and 1-41audio control compatible components.
When you select anything other than the HDM[ jack
where the AV receiver is connected as the input on the TV,
input on the AV receiver will be switched to "TV/CD".
The AV receiver will automatically power on in conjunction when it determines it to be necessary. Even if the AV
receiver is connected to an r-tl I-liD compatible TV or
player/recorder, it will not power on if it is not necessary.
It may not power on in conjunction when the TV is set to
output audio from the TV.
Linked functions with the AV receiver may not work
depending on the model. Operate the AV receiver directly
in such cases.
En
62
Memo
En
63
ONIIYO
CORPORATION
Sales & Product Planning Div. : 2-1, Nisshin-cho,
Tel: 072-831-8023
Fax: 072-831-8163
Neyagawa-shi,
OSAKA 572-8540, JAPAN
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600
Fax: 201-785-2650
ONKYO EUROPE ELECTRONICS
http://www.us.onkyo.com/
GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
http://www.eu.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH (UK BRANCH)
The Coach House 81A High Street, Marlow, Buckinghamshire,
Tel: +44-(0)1628-473-350
Fax: +44-(0)1628-401-700
SL7 lAB,
UK
ONKYO CHINA LIMITED
Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1,88, Container Port Road, Kwai Chung,
N.T., Hong Kong. Tel: 852-2429-3118
Fax: 852-2428-9039
http://www.ch.onkyo.com/
Y1002-1
SN 29400216
(C) Copyright 2010 ONKYO CORPORATION Japan. All rights reserved.
*2940021
6*
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising