8204321A0105_TDS-32 (PT3285PW
PT3290PW
Touch Screen Monitor
USER’S GUIDE
www.planar.com
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be reproduced,translated to another language
or stored in a retrieval system, or transmitted by any means, electronic, mechanical,
photocopying, recording, or otherwise, without prior written permission. Windows is a registered
trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective
holders.
The test results show that this device meets the FCC rules. Those limits are set to protect
residential areas from the devices with harmful emission. This device will produce, use and
radiate radio frequency energy. In addition, failure to follow the user’s manual to install or use
this device might produce harmful interference with radio communication. Not withstanding
the foregoing, it does not guarantee that this type of harmful interference does not occur in
some special installations. The interference caused by this device to the reception of radio
or television signals may be verified by turning it on and off. Any changes or modifications to
this TFT edge-lit LED LCD would void the user’s authority to operate this device.
Industry Canada (ICES-003): This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Important Waste Disposal Information
Please recycle or dispose of all electronic waste in accordance with local, state, and federal laws.
Additional resources can be found online at
http://www.planar.com/about/green/.
The crossed-out wheelie bin symbol is to notify consumers in areas subject to Waste Electrical and
Electronic Equipment (WEEE) Directive 2012/19/EU that the product was placed on the market after
August 13, 2005 and must not be disposed of with other waste. Separate collection and recycling of
electronic waste at the time of disposal ensures that it is recycled in a manner that minimizes impacts
to human health and the environment. For more information about the proper disposal of electronic waste,
please contact your local authority, your household waste disposal service, or the seller from whom you
purchased the product.
Table of Contents
Usage Notice
Precautions............................................................................................................................. 1
Introduction
About PT3290PW ................................................................................................................... 3
Touch Screen for PT3290PW ................................................................................................. 3
Package Overview ...................................................................................................... 4
Installation
Product Overview ........................................................................................................ 5
Front View .............................................................................................................. 5
Bottom View ........................................................................................................... 5
VESA Mount for Your Monitor ...................................................................................... 6
Start Your Installation .................................................................................................. 7
Connecting the Display (Figure 8.1) ............................................................................. 8
(Figure 8.1) ............................................................................................................. 9
User Controls
Rear Panel Controls ...................................................................................................10
How to Use the OSD Menus .......................................................................................11
OSD/Power Lock out ..................................................................................................11
On-Screen Display Menus ..........................................................................................12
Control through RS232 ...............................................................................................13
RJ45 pin defination in display side..........................................................................13
COM port setting in PC side...................................................................................13
COM command structure from PC side ..................................................................13
Configuration..........................................................................................................14
Command format....................................................................................................15
Appendix
Troubleshooting ..........................................................................................................16
Warning Signal ...........................................................................................................17
No Signal ...............................................................................................................17
Going to Sleep........................................................................................................17
Out of Range ..........................................................................................................17
Product Dimensions ...................................................................................................18
Compatibility Modes ...................................................................................................19
Touch Screen Driver Installation .................................................................................20
PT3290PW Calibration Tool Install ..........................................................................21
PT3290PW Driver Install Instructions ......................................................................23
Technical Support ................................................................................................................ 24
Usage Notice
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to
maximize the life of your unit.
Do:
� Turn off the product before cleaning.
� Touch screen surface may be cleaned using a soft clean cloth moistened with mild
window glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.
� Use a soft cloth moistened with mild detergent to clean the display housing.
� Disconnect the power plug from AC outlet if the product is not going to be used for
an extended period of time.
Don’t:
� Do not use over 16 hours per day.
� Do not touch the LED Display screen surface with sharp or hard objects.
� Do not use abrasive cleaners, waxes or solvents for your cleaning.
� Do not operate the product under the following conditions:
○ Extremely hot, cold or humid environment.
○ Areas susceptible to excessive dust and dirt.
○ Near any appliance generating a strong magneticfield.
○ In direct sunlight.
� If smoke, abnormal noise or odor emits from your Touch LED LCD Monitor, remove the power cord
immediately and call your service center.
� Never remove the rear cover of your Touch LED LCD Monitor. The display unit inside contains
high-voltage parts and may cause electric shock.
� Never try to repair your Touch LED LCD Monitor yourself. Always call your service center or a
qualified technician to fix it.
� Due to safety concerns, if the VESA mounting kit is purchased separately, pleasemake sure the
mounting kit is UL-listed, and replaceable only by service personnel.
1
Usage Notice
Consignes de sécurité
Respectez tous les avertissements, les précautions et conseils d’entretien recommandés dans ce
manuel de l’utilisateur pour maximiser la durée de vie de votre appareil.
A faire :
Éteindre le produit avant de le nettoyer.
La surface de l'écran tactile peut être nettoyée avec un chiffon doux et propre imprégné d’un
nettoyant doux du commerce pour vitres ou d'un mélange à 50/50 d'alcool isopropylique et
d'eau.
Utilisez un chiffon doux imprégné d'un détergeant doux pour nettoyer le carter de l'affichage.
Débranchez la fiche d’alimentation de la prise de courant secteur si le produit ne doit pas être
utilisé pendant une période prolongée.
A ne pas faire :
Ne pas utiliser plus de 16 heures par jour.
Ne touchez pas la surface de l’écran LED avec des objets coupants ou durs.
N'utilisez pas des produits de nettoyage abrasifs, de la cire ou des solvants pour le nettoyage.
N’utilisez pas le produit dans les conditions suivantes :
○ Environnement extrêmement chaud, froid ou humide.
○ Endroits poussiéreux ou sales.
○ Près d’appareils générant un fort champ magnétique.
○ Sous la lumière directe du soleil.
Si de la fumée, un bruit anormal ou une odeur s'échappait de votre moniteur LCD LED,
débranchez immédiatement le cordon d'alimentation
.
et appelez votre centre de réparation.
Ne retirez jamais le couvercle arrière de votre moniteur LCD LED. L’unité d’affichage contient
des éléments où circule un voltage élevé et présentant un risque d'électrocution.
N’essayez jamais de réparer vous-même votre moniteur LCD LED. Faites toujours appel à votre
centre de service ou à un technicien qualifié pour toute réparation.
Pour des raisons de sécurité, si vous achetez séparément le kit de fixation VESA,
assurez-vous que celui-ci est certifié UL, et qu’il peut être remplacé uniquement par
un technicien qualifié.
2
Introduction
About PT3290PW
The PT3290PW is a 31.5" flat panel screen with an active matrix, thin-film transistor (TFT)
edge-lit LED LCD.
This unit is to be used as commercial and light industrial equipment only.
Features include:
• Direct Analog signal input
• Direct Digital signal input
• Active matrix TFT edge-lit LED LCD technology
• 1920 x 1080 resolution
• 31.5" viewable display area - 16:9 aspect ratio
• 31.47 ~ 67.5 KHz horizontal scan
• 47 ~ 63 Hz high refresh rate
• 0.3637mm x 0.3637mm pixel pitch
• Auto adjustment function
• Multilingual OSD user control
• 600mm x 200mm and 200mmx200mm VESA mount
• Projected Capactive touch screen with USB controller
• Audio - 5W x 2
Touch Screen for PT3290PW
• Projected Capacitive 10-point touch screen
• Interface: USB controller
• Transmittance: 84%(min)
• HID: Windows® 7/8/10
• Driver:
— Windows® 7/8/10: For Projected Capacitive,the driver is a mouse emulation driver. If your
Windows version is Windows 7 or later, there is no need to install this driver. There is a HID
touch digitizer build-in driver in Windows 7/8/10.
— Linux kernel 2.6.x (32 bit & 64 bit), Apple ® Mac OS
3
Package Overview
Display
Power Cord
RJ45 TO RJ45 CABLE
xxxxxxxxx
xxxxxxxxx / xxxxxxxxx
USER’S GU
IDE
www.planartou
ch.c
om
DisplayPort CABLE
USB Cable (A to B)
No
HID
dri
ve
rs
ne
ed
ed
Co
m
pli
wh
en
an
t-
Dri
ve
rl
us
ing
es
US
s!
B!
Quick Start Guide
4
User’s Guide
Installation
Product Overview
• Front View
• Bottom View
AUDIO OUT
AUDIO IN
VGA IN
DVI-IN
HDMI
ON/OFF SWITCH
AC INPUT POWER
DP
TOUCH USB
RJ45 OUT
RJ45 IN
5
VESA Mount for Your Monitor
This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface
standard which de fines a physical mounting interface for flat panel monitors, and
corresponding with the standards of flat panel monitor mounting devices, such as wall and
table arms. The VESA mounting interface is located on the back of your monitor.
To mount the monitor on a UL certi fied swing arm or other mounting fixture, follow the
instructions included with the mounting fixture to be used.
200.00mm
200.00mm
200.00mm
200.00mm
8-M4
!
Warning!
Please select the proper screws!
The distance between the back cover surface and the bottom of the screw hole
is 10 mm. Please use four M4 screws diameter with proper length to mount your
monitor.
Please note: the optional mount must be able to support at least 44 lbs (20Kg).
6
Start Your Installation
Please follow these instructions so that you can hook up the cables to associated connectors.
1. Lay the display flat on an even surface as seen in the step 1 diagram.
2. Connect the DP, Power, and USB cables as seen in step 2 diagram.
Connect RJ45 to RJ45 Cable if remote control is required. (Optional)
3. Connect the cables to the appropriate connectors as seen in the step 3 diagram.
Step 1
Step 2
DP
RJ45 IN (Optional)
RJ45 OUT (Optional)
Power
USB
Step 3
Power
USB
RJ45 OUT
RJ45 IN
7
DP
Audio-Out
Audio-In
VGA
DVI
HDMI
Connecting the Display (Figure 8.1)
To setup this display, please refer to the following figure and procedures.
1.
2.
Be sure all equipment is turned off.
Connect the AC power cord to the power connector on the monitor and the other end
into an electrical outlet (8.1).
3. Connect the DP cable from the display’s DP input connector to the DP
connector of your host computer (8.1).
4. Connect the USB cable from USB port of your display to USB port of your computer (8.1).
5. Once the touch screen is configured, the monitor is ready for use.
!
Notice!
To ensure the display works well with your computer, please configure the display
mode of your graphics card to make it less than or equal to 1920 x 1080 resolution
and make sure the timing of the display mode is compatible with the display.
We have listed the compatible “Video Modes” of your display in the appendix
(on page 15) for your reference.
8
(Figure 8.1)
Controlling the PT3290PW monitor via RS232 (Optional)
The PT3290PW monitor can be controlled by connecting to a PC with a RJ45 terminal
diagramed below:
RJ45 In
RJ45 Out
RJ45 In
Note:
Two COM Ports are reserved for this option.
Please refer to the RS232 section starting on page 13 for more information.
9
User Controls
Rear Panel Controls
Key Name
POWER
SOURCE
UP
DOWN
+
MENU
OSD
Menu Function
Key
POWER
Power On/Off
SOURCE
To select source input port
UP
DOWN
To move up OSD item
To move down OSD item
+
To increase adjustment value or move forward to the OSD sub-layer
-
To decrease adjustment value
MENU
To show / hide the OSD menu or move backward to the OSD sub-layer
* After user makes the adjustment, the adjusted value will be saved automatically.
10
How to Use the OSD Menus
Key Name
POWER
SOURCE
UP
DOWN
+
MENU
1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button
to select among the four functions in the main menu.
2. Choose the sub-layer menus by pressing the “+” button.
3. Press “Up” or “Down” button to select the adjustment items in the sub-layer menu.If the
adjustment items have a sub-layer menu,Press the “+” button to choose it also.
4. Adjust the value of the adjustment items by pressing the “ + ” or “ - ” button.
5. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD.
6. The OSD menu will automatically close, if you have left it idle for a pre-set time.
OSD/Power Lock out
1. To Lock the OSD / Power menu buttons, please follow the instructions below:
(Please note: the monitor has to be turned ON with a valid signal pre-set)
(a.)Press and hold “Menu” and “Up” keys simultaneously for 3 seconds, then OSD will be locked
and show "OSD Locked" 3 seconds.
(b.)Press and hold “Menu” and “Down” keys simultaneously for 3 seconds, then Power button will
be locked and show "Power button Locked" 3 seconds.
2. To Unlock the OSD / Power menu buttons, please follow the instructions below:
(Please note: the monitor has to be turned ON with a valid signal pre-set)
(a.)Press and hold “Menu” and “Up” keys simultaneously for 3 seconds, then OSD will be unlocked
and show "OSD Unlocked" 3 seconds.
(b.)Press and hold “Menu” and “Down” keys simultaneously for 3 seconds, then Power button will be
unlocked and show "Power button Unlocked" 3 seconds.
Please note:
a. When the OSD lock function is selected, this indicates that all the buttons except “power”button
are now disabled.
b. When the Power button lock function is selected, this indicates that the power key is disabled;user
can not to turn off the monitor by “Power” key.
11
On-Screen Display Menus
Main OSD Menu:
Layer1
Image
Adjustment
Default
reset
(to default)
Brightness
0 ~ 100
70
Yes
Contrast
0 ~ 100
50
Yes
Sharpness
-4 ~ 4
0
Yes
9300k
Yes
Layer2
Color Temp. Menu
Layer3
Layer4
9300k
9300k
6500k
6500k
User Settings
Display
Audio
User Settings
R
0 ~ 100
100
No
G
0 ~ 100
100
No
B
0 ~ 100
100
No
Auto Adjust
Phase,
Clock,
V Position,
H Position
NA
NA
Phase
0 ~ 100
Per timing
Yes
Clock
0 ~ 100
Per timing
Yes
H Position
0 ~ 100
Per timing
Yes
V Position
0 ~ 100
Per timing
Yes
Volume
0 ~ 30
15
Yes
Mute
On/Off
Off
Yes
Default/Audio Jack
Default
Yes
VGA
No
NA
NA
12 sec
Yes
Audio Select
Input
VGA/
VGA/
DVI/
DVI/
HDMI/
HDMI/
DP
3 sec
DP
Width,
Height,
V Frequency
3 sec
6 sec
6 sec
12 sec
12 sec
30 sec
30 sec
Signal info
Osd Settings
System
Language
Timer
H Position
0 ~ 100
50
Yes
V Position
0 ~ 100
50
Yes
Transparency
0 ~ 10
0
Yes
English
English
Espanol
Espanol
Deutsch
Deutsch
French
French
English
No
Italian
Italian
日本語
日本語
中文
中文
Full
Yes
Off
Yes
Broadcast
Yes
Full
Aspect
16:10
4:3
On
DCR
Reset
Off
Reset
Monitor ID
Broadcast(1) ~ 9
12
Control through RS232
1. RJ45 pin definition on display side:
Pin No.
Name
Type of connector: RJ45 8-pin male:
1
NC
2
NC
3
NC
4
RXD (Receiving data)
5
TXD (Transmit data)
6
GND
7
NC
8
NC
Pin 8
Pin 1
2.1 COM port setting in PC side:
PROTOCOL
RS-232C
BAUD RATE
9600 (bps)
DATA LENGTH
8 (bits)
PARITY BIT
NONE
STOP BIT
1 (bit)
FLOW CONTROL
NONE
2.2 COM command structure from PC side:
Header
Message
Check code
Delimiter
Header: specify the start of this command package.
Message: command body, it comprises OP code page, OP code, parameters, checksum.
Delimiter: end of package.
* The detail structure statement, please refer the command format sheet.
13
3. Configuration
These monitors can be daisy-chained together. Except Broadcast mode, every monitor in this chain
should have a unique ID which can be chosen by the OSD menu. The maximum ID number of
monitors in this daisy-chain is up to 9.
If Individual mode, IDs should set correctly, then SW tool could control them individually.
Otherwise, the conflict will happen. If Broadcast mode, monitors ID setting doesn’t matter.
Daisy-chained RS232 with one COM port
PC
COM1
RS232 IN
RS232 OUT
RS232 IN
Display 2
Display 1
ID1
RS 232
ID3
RS 232
Display 3
Monitor ID can be adjusted by OSD menu as below:
14
RS232 IN
RS232 OUT
RS232 IN
RS232 OUT
ID2
RS 232
ID4
RS 232
Display 4
4. Command format
Operation
Write
Read
POWER OFF
POWER ON
VGA
DVI
HDMI
DISPLAY PORT
Header
Byte0 Byte1
Byte2
Byte3 Byte4
Byte5
Byte6 Byte7 Byte8 Byte9
Fix code
SOH Fix code MonitorID('*')
STX OP code page
0x01 0x30
0x2A ('*')
0x30 0x45('E') 0x30('0') 0x41('A') 0x02 0x30
0x31
0x01 0x30
0x2A ('*')
0x30 0x43('C') 0x30('0') 0x36('6') 0x02 0x30
0x31
0x01 0x30
0x2A
0x30
0x45
0x30
0x41
0x02 0x30
0x30
0x01 0x30
0x2A
0x30
0x45
0x30
0x41
0x02 0x30
0x30
0x01 0x30
0x2A
0x30
0x45
0x30
0x41
0x02 0x30
0x32
0x01 0x30
0x2A
0x30
0x45
0x30
0x41
0x02 0x30
0x32
0x01 0x30
0x2A
0x30
0x45
0x30
0x41
0x02 0x30
0x32
0x01 0x30
0x2A
0x30
0x45
0x30
0x41
0x02 0x30
0x32
15
Message
Delimiter
Byte10 Byte11 Byte12 Byte13 Byte14 Byte15 Byte16
BYTE17
OP code
Parameters
ETX
Checksum
0x31
0x30
0x30
0x30
0x36
0x34
0x03 XOR from Byte1 to Byte16
0x0D
None
0x31
0x30
0x03 XOR from Byte1 to Byte16
0x0D
0x30
0x33
0x30
0x30
0x30
0x30
0x03
0x1C
0x0D
0x30
0x33
0x30
0x30
0x30
0x31
0x03
0x1D
0x0D
0x43
0x42
0x30
0x30
0x30
0x30
0x03
0x1C
0x0D
0x43
0x42
0x30
0x30
0x30
0x31
0x03
0x1D
0x0D
0x43
0x42
0x30
0x30
0x30
0x32
0x03
0x1E
0x0D
0x43
0x42
0x30
0x30
0x30
0x33
0x03
0x1F
0x0D
Appendix
Troubleshooting
If you are experiencing trouble with the display, refer to the following. If the problem persists,
please contact your local dealer or our service center.
Problem: No image appears on screen.
► Check that all the I/O and power connectors are correctly and well connected
as described in the “Installation” section.
► Make sure the pins of the connectors are not crooked or broken.
Problem: Partial Image or incorrectly displayed image.
► Check to see if the resolution of your computer is higher than that of the display.
► Recon figure the resolution of your computer to make it less than or equal to
1920 x 1080.
Problem: Image has vertical flickering line bars.
► Use “Phase” in “Display” to make an adjustment.
► Check and recon figure the display mode of the vertical refresh rate of your graphic
card to make it compatible with the display.
Problem: Image is unstable and flickering
► Use “Phase” in “Display” to make an adjustment.
Problem: Image is scrolling
► Check and make sure the VGA signal cable (or adapter) is securely connected.
► Check and reconfigure the display mode of the vertical refresh rate of your
graphics card to make it compatible with the display.
Problem: Vague image (characters and graphics)
► Use “Phase” in “Display” to make an adjustment. If this problem still exists, use “H Position”
to make an adjustment.
Problem: Touch no function
► Operating systems require 15 seconds to recognize the PT3290PW after connecting
the USB cable and power cable.
16
Warning Signal
If you see warning messages on your screen, this means that the display cannot receive a
clean signal from the computer graphics card.
Below are the three kinds of Warning Signal. Please check the cable connections or contact
your local dealer or our service center for more information.
No Signal
This message means that the display has been powered on but it cannot receive any signal
from the computer graphics card. Check all the power switches, power cables, and video cable.
Going to Sleep
The display is under the power saving mode. In addition, the display will enter power saving
mode when experiencing a sudden signal disconnecting problem.
The monitor can be activated by pressing any keyboard, triggering the mouse or touching
the screen.
Out of Range
This message means that the signal of the computer graphic card is not compatible with
the display. When the signal is not included in the “Video Modes” list we have listed in the
Appendices of this manual, the monitor will display this message.
17
Product Dimensions
64.60 mm
34.00 mm
481.90 mm
787.30 mm
Front View
200.00 mm
200.00 mm
Side View
200.00 mm
200.00 mm
8-M4
Back View
18
Compatibility Modes
The monitor shall synchronize with any vertical frequency from 56.25 Hz to 85.08 Hz, and with any
horizontal frequency from 31 .469KHz to 91.146 KHz.
If the input frequency is out of the above-specified
range, the monitor shall display a warning screen indicating that the input frequency is out of range.
Under no circumstances shall any combination of input signals cause any damage to the monitor.
Compatible modes see Figure 1
Figure 1
Resolution
640 x 350
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
720 x 400
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1280 x 720
1280 x 768
1280 x 960
1280 x 960
1360 x 768
1360 x 768
1366 x 768
1280 x 1024
1280 x 1024
1280 x 1024
1680 x 1050
1600 x 1200
1920 x 1080
Compatible modes
V Freq. (Hz)
85.08
85.08
59.94
60
72.809
75
85.008
70.087
85.039
56.25
60.317
72.188
75
85.061
60
70.069
75.029
84.997
70.012
75
59.856
59.87
60
85.002
59.96
74.892
59.79
60.02
75.025
85.024
59.954
60
59.934
H Freq. (KHz)
37.861
37.861
31.469
31.5
37.861
37.5
43.269
31.469
37.927
35.156
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.677
63.851
67.5
44.772
47.776
60
85.938
47.368
60.288
47.712
63.981
79.976
91.146
65.29
75
66.587
19
Standard
VESA
VESA
VESA
VESA
VESA
VESA
VESA
IBM
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
CVT
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
CVT
VESA
VESA
Touch Screen Driver Installation
The PT3290PW Series is available with USB connection. The touch driver is available at
www.planar.com/support for these operating systems: Windows® 7/8/10,Linux kernel 2.6.x
(32 bit & 64 bit), Apple® Mac OS. (Windows 7/8/10 Multi touch without driver)
Please Note:
1. The PT3290PW is Microsoft Windows® HID (Human Interface Device) compatible
if you use the USB touch screen interface. No additional software driver is required for
general operation of the touch screen.
2. Operating systems require 15 seconds to recognize the PT3290PW after connecting the
USB cable and power cable.
20
PT3290W Calibration (Optional):
Calibrating the touch screen in Windows 7/8/10:
1. Tap the Start button, Control Panel and then Hardware and Sound.
2. Under Tablet PC Settings, tap Calibrate the screen for pen or touch input.
3. On the Display tab, under Display options, tap Calibrate and then Yes to allow the
program to make changes.
4. Follow the on-screen instructions to calibrate the touch screen.
21
22
PT3290PW Driver Installation Instructions:
If you are using a PC running, Windows® 7/8/10, follow the instructions below:
1. Power on the PC.
2. Make sure that the USB cable is connected to the computer.
3. Windows® 7/8/10: For Projected Capacitive,the driver is a mouse emulation driver. If your
Windows version is Windows 7 or later, there is no need to install this driver. There is a HID touch
digitizer build-in driver in Windows 7/8/10.
If you are using a PC running driver Linux kernel 2.6.x (32 bit & 64 bit),
follow the instructions below:
1.
2.
3.
4.
Power on the PC.
Make sure that the USB cable is connected to the computer.
Visit www.planar.com/support.
Follow the step-by-step instructions as shown on the pop-up windows.
If you are using a PC running Linux or Apple® Mac OS, follow the
instructions below:
1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Follow the step-by-step instructions found in the zipped file at www.planar.com/support.
23
Technical Support
Cables and Accessories
To find cables and accessories for your Planar monitor, touch screen or other Planar
products visit our online store at www.PlanarOnline.com.
Technical Support
Visit Planar at http://www.planar.com/support for operations manuals, touch screen drivers,
warranty information and access to Planar’s Technical Library for online troubleshooting.
To speak with Planar Customer Support please have you model and serial number available
and dial:
Planar Support
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.
Hours: 24 hours a day, 7 days a week.
Toll or long distance charges may apply.
24
© 10/2016 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc.
Other brands and names are the property of their respective owners.
020-1324-00A
Technical information in this document is subject to change without notice.
P/N 36.55L01G001-A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising