NuPRO-E43 PICMG® 1.3 Full Size LGA1151 SHB

NuPRO-E43 PICMG® 1.3 Full Size LGA1151 SHB
PICMG
®
NuPRO-E43
1.3 Full Size LGA1151 Intel® Core™
i7/i5/i3 Processor-Based SHB
Manual Rev.:
2.00
Revision Date:
May 13, 2016
Part No:
50-13075-1000
Advance Technologies; Automate the World.
Revision History
Revision
2.00
ii
Release Date
May 13, 2016
Description of Change(s)
Initial Release
NuPRO-E43
Preface
Copyright 2016 ADLINK Technology, Inc.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks
of their respective companies.
Preface
iii
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
Additional information, aids, and tips that help users perform
tasks.
NOTE:
CAUTION:
WARNING:
iv
Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.
Preface
NuPRO-E43
Table of Contents
Preface .................................................................................... iii
List of Figures ....................................................................... vii
List of Tables.......................................................................... ix
1 Introduction ........................................................................ 1
1.1
Overview.............................................................................. 1
1.2
Features............................................................................... 1
1.3
Specifications....................................................................... 2
1.4
Block Diagram ..................................................................... 5
1.5
Functional Description ......................................................... 5
1.6
Schematics and Dimensions ............................................... 8
1.7
I/O Connectivity ................................................................... 8
1.8
Rear Panel I/O Ports............................................................ 9
1.9
Board Layout ..................................................................... 11
1.10 Onboard Connectors ......................................................... 13
1.11 Jumpers & Switches .......................................................... 20
2 Getting Started ................................................................. 21
2.1
Package Contents ............................................................. 21
2.2
Installing the CPU .............................................................. 21
2.3
Installing the CPU Fan and Heatsink................................. 25
2.4
Installing Memory Modules ................................................ 25
2.5
Driver Installation ............................................................... 28
A Appendix: BIOS Setup ...................................................... 29
A.1
Entering the BIOS.............................................................. 29
A.2
Main Menu ......................................................................... 29
A.3
Advanced Menu................................................................. 30
A.3.1
CPU Configuration.................................................... 31
Table of Contents
v
A.3.2
Memory Configuration .............................................. 34
A.3.3
System Agent (SA) Configuration............................. 35
A.3.4
Graphics Configuration ............................................. 36
A.3.5
PCI Express Configuration ....................................... 37
A.3.6
USB Configuration .................................................... 40
A.3.7
SATA Configuration .................................................. 44
A.3.8
Onboard Device Configuration ................................. 46
A.3.9
Advanced Power Management................................. 55
A.3.10
TPM 1.2 Configuration.............................................. 57
A.3.11
AMT Configuration.................................................... 58
A.3.12
Intel® Bios Guard Technology.................................. 59
A.3.13
Network Stack Configuration .................................... 60
A.3.14
CSM Configuration ................................................... 61
A.3.15
System Management................................................ 63
A.3.16
Miscellaneous Configuration..................................... 68
A.4
Security .............................................................................. 69
A.5
Boot ................................................................................... 70
A.6
Save & Exit ........................................................................ 72
B Appendix: Watchdog Timer ..............................................75
C Appendix: System Resources ..........................................77
C.1
System Memory Map ......................................................... 77
C.2
I/O Map .............................................................................. 77
C.3
Interrupt Request (IRQ) Lines............................................ 79
C.3.1
IRQ Lines PIC Mode................................................. 79
C.3.2
IRQ Lines APIC Mode .............................................. 79
C.3.3
PCI Configuration Space Map .................................. 82
C.3.4
PCI Interrupt Routing Map ........................................ 83
Important Safety Instructions............................................... 85
Getting Service ...................................................................... 87
vi
Table of Contents
NuPRO-E43
List of Figures
Figure 1-1:
Figure 1-2:
Figure 1-3:
Figure 1-4:
NuPRO-E43 Block Diagram ............................................ 5
Board Dimensions ........................................................... 8
Rear Panel I/O Ports........................................................ 9
Board Layout ................................................................. 11
List of Figures
vii
This page intentionally left blank.
viii
List of Figures
NuPRO-E43
List of Tables
Table 1-1: NuPRO-E43 I/O Connectivity .......................................... 9
Table 1-2: Rear Panel I/O Legend .................................................. 10
Table 1-3: Board Layout Legend .................................................... 12
List of Tables
ix
This page intentionally left blank.
x
List of Tables
NuPRO-E43
1
Introduction
1.1 Overview
The ADLINK NuPRO-E43 is a PICMG 1.3 System Host Board
(SHB) supporting the 6th Generation Intel® Core™ i7/i5/i3 and
Pentium® processors in LGA1151 package to deliver a scalable
high performance platform for a wide array of industrial
applications. The NuPRO-E43 supports 14nm process CPUs at up
to 3.7 GHz with integrated graphics and memory controllers,
Direct Media Interface (DMI) and Flexible Display Interface (FDI)
connectivity to the Intel® Q170 Express chipset. Dual-channel
DDR4 memory is supported up to a maximum of 32GB on two
DIMM slots.
These advanced features, coupled with PCI Express® x16 expansion capability, dual PCI Express®-based Gigabit Ethernet, SATA
6 Gb/s and USB 3.0 support make the NuPRO-E43 ideal for vision
and automation control applications.
1.2 Features
X
Supports Intel® Core™ i7/i5/i3 and Pentium® processors in
LGA1151 package
X
Integrated Intel® HD Graphics
X
PCI Express® x16 expansion capability via backplane
X
Dual Gigabit Ethernet
X
8x USB 3.0 ports (2 on rear panel, 6 on SHB)
X
4x USB 2.0 ports on backplane
X
4x SATA 6 Gb/s ports on SHB
X
4x COM ports (including 2x RS232/422/485)
X
Watchdog timer, hardware monitor
X
Optional HD audio kit (DB-Audio2 daughter board)
X
Expanded TPM hardware security module
X
RoHS compliant
Introduction
1
To purchase the optional DB-Audio2 daughter board, please
contact your ADLINK sales representative.
NOTE:
1.3 Specifications
Processor& System
2
CPU
Intel® Core™ i7-6700, 3.4GHz, 8M cache, 14nm, 65W TDP,
LGA1151 (4C/8T)
Intel® Core™ i7-6700TE, 2.4GHz 8M cache, 14nm, 35W TDP,
LGA1151 (4C/8T)
Intel® Core™ i5-6500, 3.6GHz, 6M cache, 14nm, 65W TDP,
LGA1151 (4C/4T)
Intel® Core™ i5-6500TE, 3.3GHz, 6M cache, 14nm, 35W TDP,
LGA1151 (4C/4T)
Intel® Core™ i3-6100, 3.7GHz, 3M cache, 14nm, 65W TDP,
LGA1151 (2C/4T)
Intel® Core™ i3-6100TE, 2.7GHz, 4M cache, 14nm, 35W TDP,
LGA1151 (2C/4T)
Intel® Pentium® G4400, 3.3GHz, 3M cache, 14nm, 65W TDP,
LGA1151 (2C/2T)
Intel® Pentium® G4400TE, 2.9GHz, 3M cache, 14nm, 35W
TDP, LGA1151 (2C/2T)
Intel® Celeron® G3900, 2.8GHz, 2M cache, 14nm, 65W TDP,
LGA1151 (2C/2T)
Intel® Celeron® G3900TE, 2.6GHz, 2M cache, 14nm, 35W
TDP, LGA1151 (2C/2T)
Chipset
Intel® Q170 Express
Memory
Dual channel DDR4-2133 up to 32 GB
BIOS
AMI® UEFI BIOS
128 Mbit SPI flash memory
TPM
1x box header for TPM module
Atmel AT97SC3204 TIS 1.2
WDT
1-255 sec. or 1-255 min. software programmable, can
generate system reset
Hardware
Monitor
CPU temperature, system temperature, system voltage, CPU
fan speed
Introduction
NuPRO-E43
OS
Microsoft® Windows® 7 32/64-bit
Microsoft® Windows® 8.1 64-bit
Microsoft® Windows® 10 64-bit
Ubuntu 15.10
I/O
Serial ATA
4x SATA 3.0 onboard with RAID support
Serial Ports
2x RS-232 via onboard 2.0 pitch box header
2x RS-232/422/485 with auto flow control via onboard
2.0 pitch box header
PCIe/PCI bus
(Via backplane)
1x PCIe x16 with Intel PCIe slot bifurcation support, can
be configured to 1x PCIex 16 or 2x PCIe x8 or 1x PCIe
x8 + 2x PCIe x4 to backplane (based on backplane), 1x
PCIe x4 to backplane, and 4x PCI to backplane
USB
8x USB 3.0 (2 on rear I/O& 6 onboard box header)
4x USB 2.0 to backplane
LPT Port
1x LPT port via onboard box header
Audio
1x box header for audio module DB-Audio2
KB/MS
1x pin header for PS/2 keyboard& mouse
Audio
Codec
Realtek® ALC262 support by DB-Audio2
daughter board
Interface
Intel® High Definition Audio via onboard box
header
Display
Graphics
Integrated Intel® HD series, based on CPU
for different GPU
VGA
1x VGA on rear I/O, resolution up to 1920 x
1200@60Hz
DVI-D
1x DVI-D via onboard pin header, resolution
up to 1920 x 1200@60Hz
Introduction
3
Ethernet
Controller
LAN1: Intel® I219LM PHY via RJ45
LAN2: Intel®I211-AT via RJ45
Interface
PCIe x1 bus
iAMT
Support iAMT 11
Wake On LAN
Support on LAN1
Manageability
SEMA
SEMA support with BMC
SEMA Cloud
Mechanical and Environmental
4
Form Factor
Full-sized PICMG® 1.3 system host board
Dimensions
338 mm x 126 mm (L x W)
Operating Temperature
0 to 60°C
Storage Temperature
-40 to 80°C
Certification
CE & FCC Class A
Relative Humidity
5% to 95%, non-condensing
Introduction
NuPRO-E43
1.4 Block Diagram
Figure 1-1: NuPRO-E43 Block Diagram
1.5 Functional Description
Processor Support
The NuPRO-E43 is PICMG 1.3 System Host Board supporting the
6th Generation Intel® Core™ processor family (Intel® Core™ i7/
i5/i3) in LGA1151 socket. An integrated memory controller supports dual channel DDR4 and Intel® HD Graphics is integrated
onboard the CPU. The CPU provides a PCI Express x16 for external graphics or expansion. Direct Media Interface (DMI) and Flexible Display Interface (FDI) provide connectivity to the Intel® Q170
Express Chipset.
Intel® Q170 Express Chipset
The Intel® Q170 Platform Controller Hub (PCH), with the processor, provides a compact yet powerful 2-chip solution, with Direct
Media Interface (DMI) chip-to-chip connection between the pro-
Introduction
5
cessor and PCH and Intel Flexible Display Interface transmitting
display traffic from processor-based integrated graphics to the legacy display connectors in the PCH, including PCI Express, SATA
6 Gb/s, USB 3.0, LPC and SPI.
Dual-Channel DDR4 Memory
To meet the requirements of memory-intensive applications,
NuPRO-E43 dual-channel memory architecture supports DDR4
2133 MHz DIMMs, which delivers higher bandwidth and increased
performance with lower power consumption than DDR3.
Gigabit Ethernet
The NuPRO-E43 utilizes an Intel® I219LM Gigabit Ethernet PHY
and Intel® I211-AT Gigabit Controller connected to the PCI-E bus
of the Q170 PCH, with Intel® AMT 11 (I219LM on LAN1), Wakeon-LAN, and PXE supported.
Serial ATA
The NuPRO-E43 provides four Serial ATA ports with data transfer
rates of up to 6.0 GB/s. Intel® Rapid Storage Technology supports
AHCI and RAID 0/1/5/10 functionality.
Universal Serial Bus (USB 2.0/3.0)
The NuPRO-E43 provides 4 USB 2.0 ports (backplane) supporting
transfer rates up to 480 Mb/s and 8 USB 3.0 ports (2x on rear
panel, 6x on SHB) supporting transfer rates up to 5 Gb/s. All ports
are USB 2.0/1.1 compatible.
Hardware Monitoring
A built-in, proactive hardware monitoring system in the Super I/O
monitors the CPU temperature, system fan speed, and voltage
levels to prevent overheating and/or component damage, effect
timely failure detection, and ensure stable supply of current for
critical components.
6
Introduction
NuPRO-E43
Watchdog Timer
The watchdog timer (WDT) monitors system operations based on
user-defined configurations. The WDT can be programmed for different time-out periods, such as from 1 to 255 seconds or from 1 to
255 minutes. The WDT generates a reset signal, then a reset
request, after failure to strobe it within the programmed time
period. A register bit may be enabled to indicate if the watchdog
timer caused the reset event. The WDT register is cleared during
the power-on sequence to enable the operating system to take
appropriate action when the watchdog generates a reboot.
Trusted Platform Module
The NuPRO-E43 optionally supports TPM ver. 1.2 (Trusted Platform Module) for secure storage of keys, passwords and digital
certificates. Systems supporting TPM offer improved hardwarebased security in numerous applications, such as file and folder
encryption, local password management, S-MIME e-mail, VPN
and PKI authentication and wireless authentication for 802.1x and
LEAP.
Intel® Active Management Technology
Intel® Active Management Technology (Intel® AMT) is hardwarebased technology for remotely managing and securing PCs out-ofband. Intel® AMT includes hardware-based remote management,
security, power-management, and remote-configuration features.
Intel® AMT allows remote access to a system when traditional
techniques and methods are not available.
Introduction
7
1.6 Schematics and Dimensions
All dimensions shown are in mm (millimeters).
NOTE:
338.1
333.6
151.8
39.6
20.6
126.4
123.1
126.4
111
Figure 1-2: Board Dimensions
1.7 I/O Connectivity
I/O
Bracket
Onboard
Edge
Connector
Remarks
VGA
Y
—
—
DB-15
DVI-D
—
Y
—
Cable w/ bracket
optional
LAN1/2 (RJ-45)
Y
—
—
Act/Link/
Speed LEDs
PS/2 KB/MS
—
Y
—
Cable w/ bracket
optional
USB rear panel
2
—
—
USB 3.0
6
—
Cable w/ bracket
optional
USB 3.0 headers —
8
USB backplane
—
—
4
USB 2.0
COMA-D
—
Y
—
2.00” pitch
Introduction
NuPRO-E43
I/O
Bracket
Onboard
Edge
Connector
Remarks
SATA
—
4
—
—
PCIe x4
—
—
Y
—
PCIe x16
—
—
Y
—
PCI 32bit/33MHz —
—
Y
via ITE IT8892
Table 1-1: NuPRO-E43 I/O Connectivity
1.8 Rear Panel I/O Ports
A
B
C
D
Figure 1-3: Rear Panel I/O Ports
Connector
Description
A
LAN1 (RJ-45)
Gigabit Ethernet (supports Intel® AMT)
B
LAN2 (RJ-45)
Gigabit Ethernet
Introduction
9
Connector
C
VGA
D
USB 3.0 x2
Description
DB-15 connector for CRT or LCD monitor
SuperSpeed USB 3.0 ports
Table 1-2: Rear Panel I/O Legend
USB 3.0 Connectors
Pin #
Signal Name
1
USB3.0_P5VA
2
USB2_CMAN
3
USB2_CMAP
4
GND
5
USB3A_CMRXN
6
USB3A_CMRXP
7
GND
8
USB3A_CMTXN
9
USB3A_CMTXP
LAN (RJ-45) Ports
LED1
LED2
8
1
Pin #
10BASE-T/
100BASE-TX
1000BASE-T
1
TX+
BI_DA+
2
TX-
BI_DA-
3
RX+
BI_DB+
4
--
BI_DC+
5
--
BI_DC-
6
RX-
BI_DB-
7
--
BI_DD+
8
--
BI_DD-
LED1
10
LED2
Status
Description
Status
Description
Off
No Link
Off
10 Mb connection
Introduction
NuPRO-E43
LED1
LED2
On
Linked
Green
100 Mb connection
Blinking
Data Activity
Amber
1 Gb connection
VGA Port
Pin #
Signal
Pin #
Signal
1
Red
9
+5 V
2
Green
10
Ground
3
Blue
11
NC
4
NC
12
DDC DAT
5
Ground
13
HSYNC
6
Ground
14
VSYNC
7
Ground
15
DDC CLK
8
Ground
1.9 Board Layout
A B C
D E F
G
H
I
L
J
K
N
O
S
M
P
T
U
R
Q
V
W
Figure 1-4: Board Layout
Introduction
11
Connector
Description
A
CN40
DIMM B0
B
CN39
DIMM A0
C
CN36
Power 4-pin (ATX 12V)
D
FAN1
Fan1(CPU fan)
E
CN35
USER (system panel pin header)
F
CN34
DVI (DVI-D)
G
(Top
down)
CN30
CN31
CN32
CN33
SATA #0
SATA #1
SATA #2
SATA #3
H
CN26
USB3.0 #3/4
I
CN27
USB3.0 #5/6
J
CN28
USB3.0 #7/8
K
CN22
LPT
L
CN9
COM C
M
CN10
COM D
N
CN7
COM A
O
CN8
COM B
P
CN17
TPM
Q
CN5
Audio
R
CN20
DB40
Rear Side Mounted
S
CN24
USB3.0#1
T
CN25
USB3.0#2
U
CN1
D-SUB
V
CN4
I211 LAN
W
CN3
I219 LAN
Table 1-3: Board Layout Legend
12
Introduction
NuPRO-E43
1.10 Onboard Connectors
COMA to D Connector (RS-232) (CN7/8/9/10)
1
Pin #
RS-232 Signal
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
NC
2
9
10
Connector
Pitch
COMA
(COM1)
COMB
(COM2)
CN7
CN8
2.00 mm 2.00 mm
COMC
(COM3)
COMD
(COM4)
CN9
CN10
2.00 mm
2.00 mm
COMA to B Connector (RS-422/485) (CN7/8)
1
9
Introduction
2
10
Pin #
RS-422
RS-485
1
TXD-
Data-
2
NC
NC
3
TXD+
Data+
4
NC
NC
5
RXD+
NC
6
NC
NC
7
RXD-
NC
8
NC
NC
9
GND
GND
10
NC
NC
13
USB 3.0 Connectors (CN26/27/28)
Pin #
1
14
20
Signal
Pin #
Signal
1
P5V_USB3B
20
NC
2
S_USB3_RN3_R
19
P5V_USB3B
3
S_USB3_RP3_R
18
S_USB3_RN4_R
4
GND
17
S_USB3_RP4_R
5
S_USB3_TN3_R
16
GND
6
S_USB3_TP3_R
15
S_USB3_TN4_R
7
GND
14
S_USB3_TP4_R
8
S_USB2_N2_R
13
GND
9
S_USB2_P2_R
12
S_USB2_N3_R
10
S_USB_OC1#
11
S_USB2_P3_R
Introduction
NuPRO-E43
DVI-D Onboard Connector(CN34)
Pin # Signal
2
20
Introduction
1
19
1
GND
2
GND
3
TMD_CKP
4
TMD_N2
5
TMD_CKN
6
TMD_P2
7
GND
8
GND
9
TMD_SCL
10
TMD_N1
11
TMD_SDA
12
TMD_P1
13
GND
14
GND
15
TMD_HPD
16
TMD_N0
17
+5V_PSU_DVI
18
TMD_P0
19
GND
20
GND
15
DVI-D Bracket Connector
(optional cable w/ bracket, P/N 30-01052-2000)
Pin #
Signal
Pin #
Signal
1
TMDS Data2-
13
TMDS Data3+
2
TMDS Data2+
14
+5 V Power
3
TMDS Data2/4 Shield
15
GND
4
TMDS Data4-
16
Hot Plug Detect
5
TMDS Data4+
17
TMDS Data0-
6
DDC Clock [SCL]
18
TMDSData0+
7
DDC Data [SDA]
19
TMDS Data0/5 Shield
8
Analog vertical sync
20
TMDS Data5-
9
TMDS Data1-
21
TMDS Data5+
10
TMDS Data1+
22
TMDS Clock Shield
11
TMDS Data1/3 Shield
23
TMDS Clock +
12
TMDS Data3-
24
TMDS Clock -
ATX 12V Power Connector (CN36)
Pin #
16
2
1
4
3
Signal
1
GND
2
GND
3
+12V DC
4
+12V DC
Introduction
NuPRO-E43
PS/2 Keyboard/Mouse Pin Header (CN37)
Pin #
2
4
6
1
3
5
Signal
1
KBCLK_R
2
KBDATA_R
3
MSCLK_R
4
MSDATA_R
5
GND
6
KM_VCC
Serial ATA Connectors (CN30~33)HD Audio Daughter
Pin #
Signal
1
2
3
4
5
6
7
GND
TXP
TXN
GND
RXN
RXP
GND
1
7
Board Connector (CN5)
This connector is designed for use with the ADLINK DB-Audio2
daughter board.
1
9
Introduction
2
10
Pin #
Signal
Function
1
GND
2
AUD_BCLK
3
GND
4
ICH_AUD_SDIN1
5
P5V
6
ICH_AUD_SDOUT
7
P5V_AUD
8
P3V3_DVDD
3.3V
9
AUD_SYNC
Audio Synchronous
10
AUD_RSTJ
Audio Reset
Ground
Audio Clock
Ground
Audio Data Input
+ 5V
Audio Data Output
+ 5V
17
System Panel Connector (CN35)
Connects to chassis-mounted buttons, speakers, and LEDs.
Pin #
2
1
20
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Signal
GND
SPKR
RSTBTN
NC
NC
NC
GND
+5V_PSU
PWRBTN
NC
NC
GND
NC
KEYLOCK
HLED
PLED
HLED_POWER
NC
NC
+5V_PSU
Fan Connector (FAN1)
Pin #
1
4
18
1
Signal
GND
2
Fan power (+12V)
3
Fan Tachometer
4
Fan Speed Control
Introduction
NuPRO-E43
1.11 Jumpers & Switches
Clear CMOS Jumper (CN41)
To clear the BIOS settings (RTC RST#):
1. Power down and disconnect power from the system.
2. Short pins 2-3 on CN41.
3. Reconnect power and power up the system.
4. Wait 3 seconds or more.
5. Power down and disconnect power from the system.
6. Re-short pins 1-2, and power up the system..
CMOS Status
Connection
Normal
1–2
Clear CMOS
2–3
CN41
Clear RTC Jumper (CN42)
To clear the BIOS settings and data/time (SRTCRST#):
1. Power down and disconnect power from the system.
2. Short pins 2-3 on CN42.
3. Reconnect power and power up the system.
After power up, remove the jumper cap from pins 2-3 and reinstall it to
pins 1-2.
CMOS Status
Connection
Normal
1–2
Clear CMOS
2–3
CN42
To clear CMOS, clear both CMOS and RTC jumpers at the same
time.
Introduction
19
This page intentionally left blank.
20
Introduction
NuPRO-E43
2
Getting Started
2.1 Package Contents
Before unpacking, check the shipping carton for any damage. If
the shipping carton and/or contents are damaged, inform your
dealer immediately. Retain the shipping carton and packing
materials for inspection. Obtain authorization from the dealer
before returning any product to ADLINK.
X
NuPRO-E43
X
SATA data cable with latch (x2)
X
2-port USB 3.0 cable with bracket (2.0 mm pitch)
X
2-port COM cable with bracket (2.0 mm pitch)
X
Printer port cable with bracket (2.0 mm pitch)
WARNING:
The NuPRO-E43 must be protected from static discharge and
physical shock. Never remove any of the socketed parts except
at a static-free workstation. Use the anti-static bag shipped with
the product to handle the board. Wear a grounded wrist strap
when installing and/or servicing.
2.2 Installing the CPU
The NuPRO-E43 supports an Intel® Core™ i7/i5/i3 or Pentium®
processor in an LGA1151 socket.
X Disconnect all power to the board before
WARNING:
Getting Started
installing a CPU to prevent damaging the
board and CPU.
X Do not touch socket contacts. Damaging the
contacts voids the product warranty. Follow the
installation instructions carefully to avoid damaging the board components.
21
To install the CPU:
1. Press down on the locking arm (A), then push it away from
the socket to disengage it from the retention tab (B).
A
B
2. Raise the locking arm to unlock the load plate.
3. Lift the load plate to uncover the socket.
22
Getting Started
NuPRO-E43
4. Remove the plastic protective cover from the socket.
Note the locations of the alignment keys (A) and Pin 1
indicator (B).
A
B
Do NOT touch socket contacts.
WARNING:
5. Hold the CPU using thumb and forefinger as shown.
Position the CPU over the socket, matching the notches
on the sides of the CPU with the alignment keys on the
socket (A). The golden triangle on the CPU must be
positioned at the corner of the socket with the Pin 1 indicator as shown (B).
B
A
The CPU fits into the socket in only one orientation. DO NOT
force it into the socket to avoid causing damage.
WARNING:
Getting Started
23
Carefully place the CPU into the socket vertically. The
socket has cutouts for your fingers to fit into.
Cutouts
6. Gently lower the load plate. Make sure the front edge of
the plate is under the screw as indicated.
7. Lower the locking arm and fasten it to the retention tab
(A). The load plate should be locked underneath the
screw as shown (B).
B
A
24
Getting Started
NuPRO-E43
2.3 Installing the CPU Fan and Heatsink
WARNING:
The CPU requires a chassis with an airflow inlet and maximum
internal ambient temperature of 50° C. A especially-designed
CPU fan and heatsink must be installed before using the SHB.
Failure to install a CPU fan and heatsink may damage the system host board and/or the CPU..
If CPU fan installation procedures presented here are inconsistent
with the installation procedures you obtained from the CPU fan
and heatsink package, follow the latter.
To install the CPU fan:
1. Apply thermal grease evenly on top of the installed CPU.
2. Lower the CPU fan to the CPU, then secure it using the
provided attachments or screws.
3. Connect the CPU fan cable to the CPU fan connector on
the SHB labeled FAN1.
2.4 Installing Memory Modules
The NuPRO-E43 supports up to 32 GB of DDR4 2133 MHz
memory on two DIMM sockets. DDR4 modules have a 288-pin
footprint compared to DDR3's 240-pin DIMM.
Disconnect all power to the board before installing a memory
module to prevent damaging the board and memory module.
WARNING:
Getting Started
25
Memory Configuration Options
4GB, 8GB, and 16GB unbuffered non-ECC DDR4 DIMM are supported in the following configurations.
X
Channel A: DIMMA0
Channel B: DIMMB0
X
For dual-channel configuration, the total size of memory
module installed per channel must be the same
(DIMMA0 = DIMMB0).
X
It is recommended that you install DIMMs with the same
CAS latency. For maximum compatibility, install memory
modules with the same brand, model, and/or rating.
To install a memory module:
1. Locate the DIMM sockets on the motherboard.
2. Press the socket’s retaining clips outward to unlock.
3. Align the memory module on the socket making sure
that the notch matches the break on the socket.
26
Getting Started
NuPRO-E43
Notch
Break
4. Insert the module firmly into the slot until the retaining
clips snap back inwards and the module is securely
seated.
Getting Started
27
2.5 Driver Installation
Download requisite drivers, as follows, for your system from http://
www.adlinktech.com and install.
X
Chipset
X
Display
X
Ethernet
X
Rapid Storage
X
USB 3.0
X
Management Engine
WARNING:
28
In order to enable RAID or AHCI mode, you must pre-install the
Intel® Rapid Storage Technology driver during the Windows* installation process. using the F6 installation method.
*Not required for Windows Vista and Windows 7.
Getting Started
NuPRO-E43
Appendix A BIOS Setup
The following chapter describes basic navigation for the
AMIBIOS® EFI BIOS setup utility.
A.1 Entering the BIOS
To enter the setup screen, follow these steps:
1. Power on the motherboard
2. Press < Delete > when the prompt appears:
A.2 Main Menu
When UEFI Setup is started, the Main menu appears, displaying
the system overview.
BIOS Setup
29
System Language
Selects the default system language.
System Date
Sets the date. Use Tab to switch between date elements.
System Time
Sets the time. Use Tab to switch between time elements.
A.3 Advanced Menu
Accesses CPU Configuration, Memory Configuration, System
Agent (SA) Configuration, Graphics Configuration, PCI Express
Configuration, USB Configuration, SATA Configuration, Onboard
Device Configuration, Advance Power Management, TPM 1.2
Configuration, AMT Configuration, Intel® Bios Guard Technology,
30
BIOS Setup
NuPRO-E43
Network Stack Configuration, CSM Configuration, System Management, Miscellaneous Configuration.
A.3.1
BIOS Setup
CPU Configuration
31
Hyper-threading
(Appears if CPU supports Hyper Threading)
Enabled for Windows and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS (OS not optimized for
Hyper-Threading Technology). When Disabled only one thread
per enabled core is enabled.
Active Processor Cores
Number of cores to be enabled in each processor package.
Intel Virtualization Technology
When enabled, VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.
CPU AES
Enables/disables CPU Advanced Encryption Standard instructions
32
BIOS Setup
NuPRO-E43
Intel® Speed Shift Technology
Enables/disables Intel® Speed Shift Technology support. Enabling
displays the CPPC v2 interface to allow hardware controlled Pstates.
Intel® SpeedStep™
Allows more than two frequency ranges to be supported.
Turbo Mode
Enables/disables Turbo Mode.
CPU C states
Enables/disables CPU C states
CState Pre-Wake
Disable sets bit 30 of POWER_CTL MSR(0x1FC) to 1 to disable
the Cstate Pre-Wake.
Package C State limit
Package C State limit
CPU DTS
Disabled: ACPI thermal management uses EC reported temperature values.
Enabled: ACPI thermal management uses DTS SMM mechanism
to obtain CPU temperature values.
Out of Spec: ACPI Thermal Management uses EC reported temperature values and DTS SMM is used to handle Out of Spec condition.
BIOS Setup
33
TCC Activation Offset
Offset from the factory TCC activation temperature.
ACPI 3.0 T-States
Enables/disables ACPI 3.0 T-States.
Intel TXT(LT) Support
Enables or Disables Intel® TXT(LT) support.
A.3.2
Memory Configuration
Memory Remap
Enables/disables Memory Remap above 4GB.
34
BIOS Setup
NuPRO-E43
A.3.3
System Agent (SA) Configuration
VT-d
Enables VT-d capability
Above 4GB MMIO BIOS assignment
Enables/disables Memory MappedIO BIOS assignment over 4GB,
disabled automatically when Aperture Size is set to 2048MB.
BIOS Setup
35
A.3.4
Graphics Configuration
Primary Display
Sets the Primary Display from among IGFX/PEG/PCIE.
Internal Graphics
Keeps IGFX enabled based on the setup options.
GTT Size
Sets GTT size.
Aperture Size
Sets Aperture size.
36
BIOS Setup
NuPRO-E43
Above 4GB MMIO BIOS assignment is automatically enabled
when a 2048MB aperture is set; to use, disable CSM Support.
NOTE:
DVMT Pre-Allocated
Sets DVMT 5.0 Pre-Allocated (Fixed) graphics memory size used
by the internal graphics device.
DVMT Total Gfx Mem
Sets DVMT5.0 total graphic memory size used by the internal
graphics device.
A.3.5
PCI Express Configuration
PCI Express port allocation B0 to B3 depends on backplane
design, whether 1x4 or 4x1.
BIOS Setup
37
A.3.5.1
PEG Port Configuration
Peg 1
Max Link Speed
Sets PEG 1 maximum speed, from among Auto, Gen1, Gen2,
and Gen3.
Max Payload size
(Appears if a PEG 1 device is present)
Sets PEG 1 maximum payload size, from Auto (Default Device
Capability) or forced to 128/256 bytes.
Peg 2
Max Link Speed
Sets PEG 2 maximum speed, from among Auto, Gen1, Gen2,
and Gen3.
38
BIOS Setup
NuPRO-E43
Max Payload size
(Appears if a PEG 2 device is present)
Sets PEG 2 maximum payload size, from Auto (Default Device
Capability) or forced to 128/256 bytes.
Peg 3
Max Link Speed
Sets PEG 3 maximum speed, from among Auto, Gen1, Gen2,
and Gen3.
Max Payload size
(Appears if a PEG 3 device is present)
Sets PEG 3 maximum payload size, from Auto (Default Device
Capability) or forced to 128/256 bytes.
A.3.5.2
BIOS Setup
PCI Express Ports B0 to B3
39
PCIe Speed
Sets PCI Express port speed from among Auto, Gen1, Gen2,
and Gen3.
Detect Non-Compliance Device
Detects non-compliant PCI Express device. If enabled,
increases POST duration.
A.3.6
40
USB Configuration
BIOS Setup
NuPRO-E43
USB Precondition
Presets USB host controller and root ports for faster enumeration.
USB Port Disable Override
Selectively enables/disables the corresponding USB port from
reporting a device connection to the controller.
USB3 Rear Port 1 to USB3 Rear Port 2
Enables/disables port.
USB3 BOX Header A1 to USB3 BOX Header A2
Enables/disables port.
BIOS Setup
41
USB3 BOX Header B1 to USB3 BOX Header B2
Enables/disables port.
USB3 BOX Header C1 to USB3 BOX Header C2
Enables/disables port.
USB2 Rear Port 1 to USB2 Rear Port 2
Enables/disables port.
USB2 BOX Header A1 to USB2 BOX Header A2
Enables/disables port.
USB2 BOX Header B1 to USB2 BOX Header B2
Enables/disables port.
USB2 BOX Header C1 to USB2 BOX Header C2
Enables/disables port.
SHB Connector C USB0 to SHB Connector C USB3
Enables/disables port.
Legacy USB Support
Enables Legacy USB support.
AUTO disables legacy support if no USB devices are connected,
DISABLE maintains USB device availability only for EFI applications.
42
BIOS Setup
NuPRO-E43
XHCI Hand-off
For OS without XHCI hand-off support, with XHCI ownership
change claimed by XHCI driver.
USB Mass Storage Driver Support
Enables/disables USB Mass Storage Driver Support.
USB transfer timeout
Sets timeout value for Control, Bulk, and Interrupt transfers, from
among 1, 5, 10, and 20 sec.
Device reset timeout
Sets USB mass storage device Start Unit command timeout, from
among 10, 20, 30, and 40 sec.
Device power-up delay
Sets the maximum time before the device reports itself to the Host
Controller, with Auto using a default Root port value of 100 ms
with Hub port delay obtained from the Hub descriptor, and Manual
delay range set from 1 to 40 seconds in one second increments.
BIOS Setup
43
A.3.7
SATA Configuration
SATA Controller(s)
Enables/disables SATA Device.
SATA Mode Selection
Determines how SATA controller(s) operate.
Alternate ID
(Appears if SATA is in RAID mode)
Reports alternate device ID.
Aggressive LPM Support
Enables PCH to aggressively enter a link power state.
44
BIOS Setup
NuPRO-E43
SATA Controller Speed
Sets the maximum speed the SATA controller can support, from
among Default, Gen1, Gen2, and Gen3.
Port 0 to Port 3
Enables/disables SATA port.
A.3.7.1
Software Feature Mask Configuration
RAID0
Enables/disables RAID0 feature.
RAID1
Enables/disables RAID1 feature.
BIOS Setup
45
RAID10
Enables/disables RAID10 feature.
RAID5
Enables/disables RAID5 feature.
A.3.8
Onboard Device Configuration
COM1 to COM4
Enables/disables individual COM ports.
COM1 Control
Sets COM1 mode from among RS232, RS422, and RS485.
46
BIOS Setup
NuPRO-E43
COM2 Control
Sets COM2 mode from among RS232, RS422, and RS485.
LPT
Enables/disables LPT.
Device Mode
Sets Printer port mode from among STD Printer Mode, SPP
Mode, EPP-1.9 and SPP Mode, EPP-1.7 and SPP Mode.
LAN #1 (Intel I219)
Enables/disables LAN #1.
LAN #1(I219) Launch PXE OpROM
Enables/disables Boot Option for Legacy Network Devices.
LAN #2 (Intel I211)
Enables/disables LAN #2.
LAN #2(I211) Launch PXE OpROM
Enables/disables Boot Option for Legacy Network Devices.
BIOS Setup
47
A.3.8.1
48
Serial Port Console Redirection
BIOS Setup
NuPRO-E43
Console Redirection
Enables/disables console redirection.
Console Redirection Settings
(Depends on Console Redirection setting))
Specify how the host computer and the remote console computer
(in use) exchange data. Both computers should have the same or
compatible settings.
COM1 Console Redirection Settings
BIOS Setup
49
COM2 Console Redirection Settings
COM3 Console Redirection Settings
50
BIOS Setup
NuPRO-E43
COM4 Console Redirection Settings
COM (PCI) Console Redirection Settings
BIOS Setup
51
Terminal Type
Emulation:.
ANSI
Extended ASCII character set
VT100
ASCII character set
VT100+
Extends VT100 to support color, function keys, etc.
VT-UTF8
UTF8 encoding maps Unicode characters onto 1 or
more bytes
Bits per second
Sets serial port transmission speed, which must be matched on
the other side, with long or noisy lines possibly requiring lower
speeds, from among 9600, 19200, 38400, 57600, and 115200.
Data Bits
Sets data bit count, from 7 or 8.
Parity
Parity bit can be sent with the data bits to detect transmission
errors.
Even
Parity bit is 0 if the 1 count in the data bits is even
Odd
Parity bit is 0 if the 1 count in the data bits is odd
Mark
Parity bit is always 1
Space
Parity bit is always 0
Mark and Space Parity do not allow error detection, and can be
used as an additional data bit.
52
BIOS Setup
NuPRO-E43
Stop Bits
Indicate the end of a serial data packet (as opposed to a start bit
indicating the beginning) with the standard setting 1 stop bit. Communication with slower devices may require more than 1 stop bit.
Flow Control
Can prevent data loss from buffer overflow. When sending data, if
the receiving buffers are full, a Stop signal stops the ANSI
Extended ASCII character set.
VT100 ASCII character set
Enables VT-UTF8 combination key support for ANSI/VT100 terminals.
Recorder Mode
When enabled, only text is transmitted, to capture terminal data.
Resolution 100x31
Enables/disables extended terminal resolution.
Legacy OS Redirection Resolution
In legacy OS, sets the number of rows and columns supported for
redirection.
Putty KeyPad
Selects FunctionKey and KeyPad on Putty, from among VT100,
LINUX, XTERMR6, SCO, ESCN, and VT400.
BIOS Setup
53
Redirection After BIOS POST
If BootLoader is selected, legacy console redirection is disabled
before booting to the legacy OS. Default is Always Enable.
EMS Console Redirection Settings
Out-of-Band Mgmt Port
Microsoft Windows Emergency Management Services (EMS)
allows remote management of Windows Server OS through a
serial port, from among COM1, COM2, COM3, COM4, and COM
(PCI Bus0,Dev22,Func3).
Terminal Type
VT-UTF8 is the preferred terminal type for out-of-band management, followed by VT100+ and then VT100, from among VT100,
VT100+, VT-UTF8, and ANSI. See Console Redirection Settings
for more about Terminal Type/Emulation.
54
BIOS Setup
NuPRO-E43
Bits per second
Sets serial port transmission speed, which must be matched on
the other side, with long or noisy lines possibly requiring lower
speeds, from among 9600, 19200, 57600, and 115200.
Flow Control
Can prevent data loss from buffer overflow. When sending data, if
the receiving buffers are full, a Stop signal stops the data flow.
Once the buffers are empty, a Start signal restarts the flow. Hardware flow control uses two lines to send start/stop signals.
A.3.9
Advanced Power Management
Power Supply Unit
In ATX, the OS turns off system power when shut down.
BIOS Setup
55
AT mode will not support S3 & S4.
NOTE:
State After G3
Sets the state entered when power is re-applied after a power failure (G3 state), from among Power On, Power Off, and Last State.
RTC Wake system from S5
Enables/disables system wake on alarm event, with FixedTime
waking the system at specified hr::min::sec, and DynamicTime
waking the system at the current time + one minute.
PCIe Slot Wake
Enables/disables PCI Express Slot wake function.
Onboard LAN Wake
Enables/disables onboard LAN wake function.
PCI/SIO Wake
Enables/disables PCI/SIO wake function.
BIOS POST Watchdog
Sets watchdog timer for BIOS POST process, from among Disabled, Second Mode, and Minute Mode.
BIOS Watchdog Timer
Appears if BIOS POST Watchdog is enabled. Sets watchdog timer
for BIOS POST process.
56
BIOS Setup
NuPRO-E43
A.3.10 TPM 1.2 Configuration
Appears if a TPM device is present.
Security Device Support
Enables/disables BIOS support for security device. When disabled, OS will not show the Security Device and TCG EFI protocol
and INT1A interface will not be available.
TPM State
Enables/disables the security device.
The computer reboots during restart to change State of the
Device.
NOTE:
BIOS Setup
57
Pending Operation
Schedules an operation for the security device.
The computer reboots during restart to change State of Security Device.
NOTE:
A.3.11 AMT Configuration
Intel AMT
Enables/disables Intel® Active Management Technology BIOS
Extension. While iAMT H/W is always enabled, this option controls
the BIOS extension execution. If enabled, additional firmware is
required in the SPI device.
58
BIOS Setup
NuPRO-E43
BIOS Hotkey Pressed
OEMFLag Bit 1: Enables/disables BIOS hotkey.
A.3.12 Intel® Bios Guard Technology
Intel® Bios Guard Support
Enables/disables Intel® BIOS Guard support.
BIOS Setup
59
A.3.13 Network Stack Configuration
Network Stack
Enables/disables UEFI Network Stack.
Ipv4 PXE Support
Appears if Network Stack is enabled.
Enables Ipv4 PXE boot support, if disabled no IPV4 PXE boot
option is created
Ipv6 PXE Support
Appears if Network Stack is enabled.
Enables Ipv6 PXE boot support, if disabled no IPV6 PXE boot
option is created.
60
BIOS Setup
NuPRO-E43
PXE boot wait time
Appears if Network Stack is enabled.
Sets wait duration to press ESC key to abort PXE boot.
A.3.14 CSM Configuration
CSM Support
Enables/disables CSM Support.
GateA20 Active
UPON REQUEST to GA20 can be disabled using BIOS services.
ALWAYS prevents disabling GA20, useful when any RT code
exceeding 1MB is executed.
BIOS Setup
61
Option ROM Messages
Sets display mode for Option ROM, from Force BIOS or Keep Current.
Network
Controls execution of UEFI and legacy PXE OpROM.
Storage
Controls execution of UEFI and legacy storage OpROM.
Video
Controls execution of UEFI and legacy video OpROM.
Other PCI devices
Sets OpROM execution policy for devices other than network,
storage, or video.
62
BIOS Setup
NuPRO-E43
A.3.15 System Management
A.3.15.1
BIOS Setup
Board Information
63
A.3.15.2
64
Temperatures and Fan Speed
BIOS Setup
NuPRO-E43
A.3.15.3
Hardware Monitor
A.3.15.4
Runtime Statistics
BIOS Setup
65
66
A.3.15.5
Flags
A.3.15.6
Power Up
BIOS Setup
NuPRO-E43
Power-Up Watchdog
Enables/disables the Power-Up Watchdog, which resets the system a set time after power up.
Timeout
Appears if Power-Up Watchdog is enabled.
Sets the time before the Power Up Watchdog resets the system,
from between 24 and 65535.
A.3.15.7
Smart Fan
CPU Fan Mode
Sets CPU fan operation, from among AUTO (Smart Fan), Fan Off,
and Fan On.
BIOS Setup
67
Trigger Temperature
From 0 to 100°C.
PWM Level
From 0 to 100kHz.
A.3.16 Miscellaneous Configuration
High Precision Timer
Enables/disables High Precision Event timer.
Port 80h Redirection
Sets destination for Port 80h cycles, from LPC Bus or PCIE Bus.
68
BIOS Setup
NuPRO-E43
Pcie Pll SSC
Sets percentage for Pcie Pll SSC, with AUTO retaining hw default,
with no BIOS override, from 0.0% to 2.0%.
A.4 Security
In addition to allowing supervisor/user passwords to be set,
changed, or cleared, the following settings are available.
Administrator Password
Sets administrator password.
User Password
Sets user password.
BIOS Setup
69
RTC Lock
When enabled, bytes 38h-3Fh in the lower/upper 128-byte bank of
RTC RAM are locked.
BIOS Lock
Enables/disables PCH BIOS Lock Enable (BLE bit).
A.5 Boot
Setup Prompt Timeout
Sets number of seconds to wait for setup activation key, with
65535 (0xFFFF) indicating indefinite wait.
Bootup NumLock State
Enables/disables keypad NumLock.
70
BIOS Setup
NuPRO-E43
Quiet Boot
Enables/disables Quiet Boot.
Fast Boot
Enables/disables boot with initialization of the minimal set of
required devices for active boot, with no effect on BBS boot
options.
Boot mode select
Selects boot mode from LEGACY or UEFI.
Boot Options #1 to #8
Sets the system boot order.
UEFI XXXXXXXX Drive BBS Priorities
Specifies the Boot Device Priority sequence from available UEFI
XXXXXXXX drives, appearing when boot mode is set as
UEFI,with XXXXXXXX indicating available devices.
XXXXXXXX Drive BBS Priorities
Specifies the Boot Device Priority sequence from available UEFI
XXXXXXXX drives, appearing when boot mode is set as Legacy,
with XXXXXXXX indicating available devices.
BIOS Setup
71
A.6 Save & Exit
Discard Changes and Exit
Exits system setup without saving any changes.
Save Changes and Reset
Resets the system after saving changes.
Discard Changes
Discards all changes made to any setup options.
Restore Defaults
Reverts to factory default values for all setup options.
72
BIOS Setup
NuPRO-E43
Save as User Defaults
Saves all changes as User Defaults.
Restore User Defaults
Reverts to user defaults for all setup options.
Launch EFI Shell from filesystem device
Initiates launch of the EFI Shell application (Shell.efi) from an
available filesystem device.
BIOS Setup
73
This page intentionally left blank.
74
BIOS Setup
NuPRO-E43
Appendix B - Watchdog Timer
The watchdog timer on the NuPro-E43 can be implemented by:
X
Embedded Application Programming Interface (EAPI)
library functions
X
SEMA library functions
Please refer to the SEMA Software Manual for detailed information:
http://www.adlinktech.com/PD/web/PD_detail.php?
cKind=&pid=1274
EAPI Library Sample Code
Ensure the SEMA driver and application have been installed, and
that, during installation, the “Install EAPI” option was enabled.
1. Include the relevant header files
#ifndef _WIN32
#include "linux/EApiOs.h"
#else /* _WIN32 */
#include "winnt/EApiOs.h"
#endif /* _WIN32 */
#include "EApi.h"
2. Initialize the EAPI
EApiLibInitialize();
3. Call the EAPI function
uint32_t
status=EApiWDogStart(Delay,EventTimeout,Res
etTimeout);
For detailed information regarding the PICMG EAPI library, please
refer to the PICMG EAPI - Embedded Application Programming
Interface specification:
http://picmg.staging.wedu.com//wp-con¬ tent/uploads/
COM_EAPI_R1_0.pdf
Watchdog Timer
75
This page intentionally left blank.
76
Watchdog Timer
NuPRO-E43
Appendix C - System Resources
C.1 System Memory Map
Address Range (hex)
Size
Description
FFA00000 – FFFFFFFF
6 MB
High BIOS Area
FEE00000 – FEEFFFFF
1 MB
MSI Interrupts
FED50000–FED5FFFF
64kB
Intel ME
FED40000 –FED40FFF
4kB
TPM
FED00000 – FED003FF
1kB
HPET
FEC80000 – FECFFFFF
512kB
Local (CPU) APIC
FEC00000 – FEC7FFFF
512kB
I/O APIC
F0000 – FFFFF
64 kB
System BIOS Area (Upper)
E8000 – EFFFF
32 kB
System BIOS Area (Lower)
C0000 – E7FFF
160 kB
PCI expansion ROM area
A0000 – BFFFF
128 kB
Video Buffer & SMM space
00000 – 9FFFF
640 kB
DOS Area
C.2 I/O Map
Hex Range
Device
020 to 021
024 to 025
028 to 029
02C to 02D
Interrupt controller, 8259 equivalent
02E to 02F
LPC SI/O (NCT6106D) configuration index/data registers
030 to 031
034 to 035
038 to 039
03C to 03D
Interrupt controller, 8259 equivalent
040, 042 to 043
050, 052 to 053
Timer, 8254 equivalent
060, 062, 064, 066 Microcontroller
061, 063, 065, 067 NMI controller
070 to 077
Real time clock controller
092
Reset generator
System Resources
77
Hex Range
Device
0A0, 0A1
0A4 to 0A5
0A8 to 0A9
0AC to 0AD
0B0 to 0B1
Interrupt controller, 8259 equivalent
0B2 to 0B3
Power management
0B4 to 0B5
0B8 to 0B9
0BC to 0BD
Interrupt controller, 8259 equivalent
2E8 to 2EF
Serial port 4
2F8 to 2FF
Serial port 2
378 to 37F
Parallel port
3B0 to 3BB
Intel® HD Graphics
3C0 to 3DF
Intel® HD Graphics
3E8 to 3EF
Serial port 3
3F8 to 3FF
Serial port 1
4D0, 4D1
Interrupt controller, 8259 equivalent
A00 to A3F
SIO PME base address
CF9
Reset control register (8 bit I/O)
1800 to 18FE
SB PM base address
F000 to F03F
Intel® HD Graphics
F040 to F05F
Intel® SMBus
F060 to F083
F090 to F097
Intel® SATA Controller
F0A0 to F0A7
Intel® AMT to SOL (COM5)
78
System Resources
NuPRO-E43
C.3 Interrupt Request (IRQ) Lines
C.3.1
IRQ Lines PIC Mode
IRQ# Pin
SERIRQ
PCI
Use
Interrupt Resource / Function
0
No
No
No
Counter 0
1
No
Yes
No
Keyboard controller
2
No
No
No
Cascade from IRQ9
3
PIRQA Yes
No
Serial Port 2 (COM2)
4
PIRQA Yes
No
Serial Port 1 (COM1)
5
PIRQA Yes
No
Serial Port 3 (COM3)
6
PIRQA Yes
No
Option for configurable sources
including PIRQx, GPIO, eSPI and
internal PCI/ACPI devices.
7
PIRQA Yes
No
Serial Port 4 (COM4)
8
No
No
Real-time clock
9
PIRQA Yes
10
No
PIRQA Yes
11
PIRQA Yes
No
Cascade to IRQ2
Yes
Option for configurable sources
including PIRQx, GPIO, eSPI,
internal PCI/ACPI devices, SCI
and TCO.
Yes
Option for configurable sources
including PIRQx, GPIO, eSPI,
internal ACPI devices, SCI, TCO,
HPET #2
12
PIRQA Yes
No
PS/2 Mouse
13
No
No
Math Processor
14
PIRQA Yes
15
No
PIRQA Yes
C.3.2
No
Parallel Port (LPT)
Yes
Option for configurable sources
including PIRQx, GPIO, eSPI and
internal ACPI devices.
IRQ Lines APIC Mode
IRQ# Pin
SERIRQ
PCI
Use
IRQ
Interrupt Resource / Function
Sharable
0
No
No
No
No
System Resources
Counter 0
79
IRQ# Pin
SERIRQ
PCI
Use
IRQ
Interrupt Resource / Function
Sharable
1
No
Yes
No
No
2
No
No
No
No
Cascade from IRQ9
3
No
Yes
No
No
Serial Port 2 (COM2)
4
No
Yes
No
No
Serial Port 1 (COM1)
5
No
Yes
No
No
Serial Port 3 (COM3)
6
No
Yes
No
Yes
Option for configurable sources
including GPIO, eSPI, internal
ACPI/ PCI devices.
7
No
Yes
No
No
Serial Port 4 (COM4)
8
No
No
No
No
Real-time clock
9
No
Yes
No
No
Cascade to IRQ2
Yes
Option for configurable sources
including GPIO, eSPI, internal
ACPI/ PCI devices, SCI and TCO.
10
No
Yes
No
Keyboard controller
11
No
Yes
No
Yes
Option for configurable sources
including GPIO, eSPI, internal
ACPI/ PCI devices, SCI, TCO,
HPET #2.
12
No
Yes
No
No
PS/2 Mouse
13
No
No
No
No
Math Processor
14
No
Yes
No
No
Parallel Port (LPT)
Yes
Option for configurable sources
including GPIO, eSPI and internal
ACPI/PCI devices.
Yes
Option for configurable sources
including internal PIRQA, GPIO,
eSPI and internal ACPI/PCI
devices.
Yes
Option for configurable sources
including internal PIRQ[B-D],
GPIO, eSPI and internal ACPI/
PCI devices
Yes
Option for configurable sources
including internal PIRQ[B-D],
GPIO, eSPI and internal ACPI/
PCI devices
15
No
16
PIR
QA
PIRQA
No
PIRQ[BD]
No
PIRQ[BD]
17
18
80
Yes
No
Yes
Yes
Yes
System Resources
NuPRO-E43
IRQ# Pin
SERIRQ
19
PIRQ[BD]
20
21
22
23
No
No
No
No
No
No
No
No
No
System Resources
PCI
Use
IRQ
Interrupt Resource / Function
Sharable
Yes
Yes
Option for configurable sources
including internal PIRQ[B-D],
GPIO, eSPI and internal ACPI/
PCI devices
Yes
Option for configurable sources
including internal PIRQ[E-H],
GPIO, eSPI, SCI, TCO, internal
ACPI/PCI devices and HPET
Yes
Option for configurable sources
including internal PIRQ[E-H],
GPIO, eSPI, SCI, TCO, internal
ACPI/PCI devices and HPET
Yes
Option for configurable sources
including internal PIRQ[E-H],
GPIO, eSPI, SCI, TCO, internal
ACPI/PCI devices and HPET
Yes
Option for configurable sources
including internal PIRQ[E-H],
GPIO, eSPI, SCI, TCO, internal
ACPI/PCI devices and HPET
No
No
No
No
81
C.3.3
PCI Configuration Space Map
Bus Device Function Routing Description
82
00h
00h
00h
N/A
Intel Host Bridge
00h
01h
00h
Internal
PEG X16/X8 Root Port
00h
01h
01h
Internal
PEG X8/X4 Root Port
00h
01h
02h
Internal
PEG X4 Root Port
00h
02h
00h
Internal
Intel Integrated Graphics
Device
00h
14h
00h
Internal
Intel USB XHCI Controller
00h
14h
02h
Internal
00h
15h
00h
Internal
Intel I2C Controller #0
Intel Thermal Controller
00h
15h
01h
N/A
Intel I2C Controller #1
00h
16h
00h
Internal
Intel® MEI
00h
16h
03h
N/A
Intel Keyboard and Text (KT)
Redirection
00h
17h
00h
Internal
Intel SATA controller
00h
1Ch
00h
Internal
PCI Express Root port 1
00h
1Ch
04h
Internal
PCI Express Root port 5
00h
1Ch
05h
Internal
PCI Express Root port 6
00h
1Ch
06h
Internal
PCI Express Root port 7
00h
1Ch
07h
Internal
PCI Express Root port 8
00h
1Dh
00h
Internal
PCI Express Root port 9
00h
1Dh
01h
Internal
PCI Express Root port 10
00h
1Eh
00h
Internal
Intel UART Controller #0
00h
1Fh
00h
Internal
Intel LPC or eSPI Controller
00h
1Fh
02h
N/A
Intel PMC Controller
00h
1Fh
03h
Internal
Intel® High Definition Audio
00h
1Fh
04h
Internal
Intel SMBus Controller
00h
1Fh
06h
Internal
Intel GbE Controller
01h
00h
00h
Internal
PEG X16/X8 SLOT
02h
00h
00h
Internal
PEG X8/X4 SLOT
03h
00h
00h
Internal
PEG X4 SLOT
04h
00h
00h
Internal
PCIE X4/X1 SLOT 1
System Resources
NuPRO-E43
Bus Device Function Routing Description
05h
00h
00h
Internal
PCIE X1 SLOT 2
06h
00h
00h
Internal
PCIE X1 SLOT 3
07h
00h
00h
Internal
PCIE X1 SLOT 4
08h
00h
00h
Internal
PCIE To PCI Bridge(IT8892E)
09h
0Fh
00h
Internal
PCI SLOT 1
09h
0Eh
00h
Internal
PCI SLOT 2
09h
0Dh
00h
Internal
PCI SLOT 3
09h
0Ch
00h
Internal
PCI SLOT 4
0Ah
00h
00h
Internal
Intel I211 LAN Controller
C.3.4
PCI Interrupt Routing Map
Description
A
B
C
D
PEG X16/X8 Root Port
INTA INTB INTC INTD
PEG X8/X4 Root Port
INTB INTC INTD INTA
PEG X4 Root Port
INTC INTD INTA INTB
Intel Integrated Graphics
Device
INTA
Intel USB XHCI Controller
INTA
Intel Thermal Controller
INTD
INTC
Intel I2C Controller #0
INTA INTB INTC INTD
Intel® MEI
INTA INTB INTC INTD
Intel SATA controller
INTA
PCI Express Root port 1
INTA INTB INTC INTD
PCI Express Root port 5
INTA INTB INTC INTD
PCI Express Root port 6
INTB INTC INTD INTA
PCI Express Root port 7
INTC INTD INTA INTB
PCI Express Root port 8
INTD INTA INTB INTC
PCI Express Root port 9
INTA INTB INTC INTD
PCI Express Root port 10
INTB INTC INTD INTA
Intel UART Controller #0
INTA INTB INTC INTD
Intel LPC or eSPI Controller
INTA INTB INTC INTD
Intel® High Definition Audio
INTA
System Resources
83
84
Description
A
B
C
D
Intel SMBus Controller
INTA
Intel GbE Controller
INTA
PEG X16/X8 SLOT
INTA INTB INTC INTD
PEG X8/X4 SLOT
INTB INTC INTD INTA
PEG X4 SLOT
INTC INTD INTA INTB
PCIE X4/X1 SLOT 1
INTA INTB INTC INTD
PCIE X1 SLOT 2
INTB INTC INTD INTA
PCIE X1 SLOT 3
INTC INTD INTA INTB
PCIE X1 SLOT 4
INTD INTA INTB INTC
PCIE To PCI Bridge(IT8892E)
INTA INTB INTC INTD
PCI SLOT 1
INTB INTC INTD INTA
PCI SLOT 2
INTC INTD INTA INTB
PCI SLOT 3
INTD INTA INTB INTC
PCI SLOT 4
INTA INTB INTC INTD
Intel I211 LAN Controller
INTB INTC INTD INTA
System Resources
NuPRO-E42
Important Safety Instructions
For user safety, please read and follow all instructions,
WARNINGS, CAUTIONS, and NOTES marked in this manual
and on the associated equipment before handling/operating the
equipment.
X
Read these safety instructions carefully.
X
Keep this user’s manual for future reference.
X
Read the specifications section of this manual for detailed
information on the operating environment of this equipment.
X
When installing/mounting or uninstalling/removing
equipment:
Z
X
Turn off power and unplug any power cords/cables.
To avoid electrical shock and/or damage to equipment:
Z
Keep equipment away from water or liquid sources;
Z
Keep equipment away from high heat or high humidity;
Z
Keep equipment properly ventilated (do not block or
cover ventilation openings);
Z
Make sure to use recommended voltage and power
source settings;
Z
Always install and operate equipment near an easily
accessible electrical socket-outlet;
Z
Secure the power cord (do not place any object on/over
the power cord);
Z
Only install/attach and operate equipment on stable
surfaces and/or recommended mountings; and,
Z
If the equipment will not be used for long periods of time,
turn off and unplug the equipment from its power source.
Important Safety Instructions
85
X
Never attempt to fix the equipment. Equipment should only
be serviced by qualified personnel.
A Lithium-type battery may be provided for uninterrupted, backup
or emergency power.
Risk of explosion if battery is replaced with one of an incorrect
type. Dispose of used batteries appropriately.
WARNING:
X
86
Equipment must be serviced by authorized technicians
when:
Z
The power cord or plug is damaged;
Z
Liquid has penetrated the equipment;
Z
It has been exposed to high humidity/moisture;
Z
It is not functioning or does not function according to the
user’s manual;
Z
It has been dropped and/or damaged; and/or it has an
obvious sign of breakage.
Important Safety Instructions
NuPRO-E42
Getting Service
Ask an Expert: http://askanexpert.adlinktech.com
ADLINK Technology, Inc.
Address:
9F, No.166 Jian Yi Road, Zhonghe District
New Taipei City 235, Taiwan
ᄅ‫ؑק‬խࡉ೴৬ԫሁ 166 ᇆ 9 ᑔ
Tel:
+886-2-8226-5877
Fax:
+886-2-8226-5717
Email:
service@adlinktech.com
Ampro ADLINK Technology, Inc.
Address:
5215 Hellyer Avenue, #110
San Jose, CA 95138, USA
Tel:
+1-408-360-0200
Toll Free: +1-800-966-5200 (USA only)
Fax:
+1-408-360-0222
Email:
info@adlinktech.com
ADLINK Technology (China) Co., Ltd.
Address:
Ϟ⍋Ꮦ⌺ϰᮄऎᓴ∳催⾥ᡔುऎ㢇᯹䏃 300 ো(201203)
300 Fang Chun Rd., Zhangjiang Hi-Tech Park
Pudong New Area, Shanghai, 201203 China
Tel:
+86-21-5132-8988
Fax:
+86-21-5132-3588
Email:
market@adlinktech.com
ADLINK Technology Beijing
Address:
࣫ҀᏖ⍋⎔ऎϞഄϰ䏃 1 োⲜ߯ࡼ࡯໻ॺ E ᑻ 801 ᅸ(100085)
Rm. 801, Power Creative E, No. 1 Shang Di East Rd.
Beijing, 100085 China
Tel:
+86-10-5885-8666
Fax:
+86-10-5885-8626
Email:
market@adlinktech.com
ADLINK Technology Shenzhen
Address:
⏅ഇᏖफቅऎ⾥ᡔುफऎ催ᮄफϗ䘧᭄ᄫᡔᴃು
A1 ᷟ 2 ὐ C ऎ (518057)
2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7
High-Tech Industrial Park S., Shenzhen, 518054 China
Tel:
+86-755-2643-4858
Fax:
+86-755-2664-6353
Email:
market@adlinktech.com
LiPPERT ADLINK Technology GmbH
Address:
Hans-Thoma-Strasse 11
D-68163 Mannheim, Germany
Tel:
+49-621-43214-0
Fax:
+49-621 43214-30
Email:
emea@adlinktech.com
PENTA ADLINK Technology GmbH
Ulrichsbergerstrasse 17
94469 Deggendorf, Germany
Tel:
+49 (0) 991 290 94 – 10
Fax:
+49 (0) 991 290 94 - 29
Email:
emea@adlinktech.com
Getting Service
87
ADLINK Technology, Inc. (French Liaison Office)
Address:
6 allée de Londres, Immeuble Ceylan
91940 Les Ulis, France
Tel:
+33 (0) 1 60 12 35 66
Fax:
+33 (0) 1 60 12 35 66
Email:
france@adlinktech.com
ADLINK Technology Japan Corporation
Address:
е101-0045 ࣟࠇຟՏ‫ضז‬㡢壀‫ض‬᝽܏᮫ 3-7-4
壀‫ ض‬374 垔垬 4F
KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho,
Chiyoda-ku, Tokyo 101-0045, Japan
Tel:
+81-3-4455-3722
Fax:
+81-3-5209-6013
Email:
japan@adlinktech.com
ADLINK Technology, Inc. (Korean Liaison Office)
Address:
凃匶壊 昷單柢 把埿割 朞喺嵢 46 憎匾 4 凃壟捒娯 2 猻
(朞喺壟 4-4 憎滆) (殶) 463-825
2F, Kyungdong B/D, 4 Sunae-ro 46 beon-gil
Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-825
Toll Free
+82-80-800-0585
Tel
+82-31-786-0585
Fax
+82-31-786-0583
Email:
korea@adlinktech.com
ADLINK Technology Singapore Pte. Ltd.
Address:
84 Genting Lane #07-02A, Cityneon Design Centre
Singapore 349584
Tel:
+65-6844-2261
Fax:
+65-6844-2263
Email:
singapore@adlinktech.com
ADLINK Technology Singapore Pte. Ltd. (Indian Liaison Office)
Address:
#50-56, First Floor, Spearhead Towers
Margosa Main Road (between 16th/17th Cross)
Malleswaram, Bangalore - 560 055, India
Tel:
+91-80-65605817, +91-80-42246107
Fax:
+91-80-23464606
Email:
india@adlinktech.com
ADLINK Technology, Inc. (Israeli Liaison Office)
Address:
27 Maskit St., Corex Building
PO Box 12777
Herzliya 4673300, Israel
Tel:
+972-54-632-5251
Fax:
+972-77-208-0230
Email:
israel@adlinktech.com
ADLINK Technology, Inc. (UK Liaison Office)
Tel:
+44 774 010 59 65
Email:
UK@adlinktech.com
88
Getting Service
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising