DR240 hybrid recorder — expandable type (Style number: S8

DR240 hybrid recorder — expandable type (Style number: S8
<<Contents>> <<Index>>
General
Specifications
DR240 hybrid recorder
— expandable type (Style number: S8)
DS400/DS600 sub units (Style number: S8)
GS 04M01D01-12E
Refer to the following cautionary notes
before you configure your system.
DARWIN is a system comprising a number of data-acquisition
equipment components.
In the course of system growth, new models, software, various
input/output modules and optional features are added to the family
to enhance the systems expandability and flexibility. You can
check the versions of your equipment and software by referring to
the style number: Sn* shown on the nameplate of the main unit.
When configuring a system, you must confirm that the style
number of each componentunit and software meets the following
requirements:
* release number in the case of software: Rn
(1) The style number of each input/output module must be the
same as or lower thanthat of the main unit or sub-unit to which
the module is connected.
(2) The release number of a dedicated software package must be
the same as or higherthan the style number of the main unit or
sub-unit where the package is installed and where it performs
control.
Any equipment/software not meeting these requirements is
incompatible with your system configuration.
For information on how to upgrade to compatible equipment/
software, consult our sales personnel.
The DR240 is a highly reliable process monitor hybrid recorder
that contains a high withstand voltage semiconductor relay developed
by Yokogawa. It uses small input modules to record measured
industrial variables, physical variables such as temperature signals in
realtime in the field, and can also transfer the measured data to a
personal computer.
The main unit of the expandable type can be connected to a
maximum of six sub units DS400/DS600. Also, you can freely connect
various input/output modules to suit the measurement conditions, and
increase the number of measurement points to a maximum of 300.
Units can be connected to each other with dedicated cable over a
distance of up to 500 m. This makes for reduced wiring and speedier
wiring work, and enables you to configure a flexible remote measurement and recording system.
In addition, by using the dedicated package software, the
measurement conditions can be set and continuous data acquisition
performed easily.
(1) Compact: Occupies only about one half of the size (depth) of the
HR2500E.
(2) High speed: Can measure 300 channels/500 ms.
(3) A large variety of inputs: Universal (DC voltage, thermocouple,
RTD, contact), DC V/TC/DI dedicated inputs, mA, power monitor,
strain, pulse, DI.
(4) Superb environmental toughness (input modules): –10°C to 60°C
(5) Remote measurement: The sub unit is designed to be connected to
the main unit with dedicated cable, enabling it to be located up to
500 m away from the main unit.
■ Outline of DR240 hybrid recorder
(1) The DR240 main unit can set and control the sub units to which it
is connected with dedicated cable.
(2) The DR240 main unit controls, communications module and DI/
DO module to which it is connected.
(3) Data measured using the input modules is collected by the DR240
main unit, via sub units.
(4) Measured phenomena can be displayed and recorded by means of
the DR240 main unit.
(5) The measured results collected by the DR240 main unit can be
transferred to a personal computer via a GP-IB, RS-232-C, RS422-A/RS-485, Ethernet interface.
■ Outline of sub units
The DS400/DS600 sub unit functions as an interface between the
expandable version of the DR230/DR240 hybrid recorder and the
various input/output modules to which it is connected.
A maximum of four input and output modules of various kinds (Max.4
slots/40 channels) can be connected to the DS400, and a maximum of
six input and output modules (Max.6 slots/60 channels) can be
connected to the DS600.
A maximum of six sub units can be connected to one main unit. Both
DS400 and DS600 sub units can be connected to the same main unit.
The main unit can be connected to the sub units, or the sub units to each
other, with dedicated cable, enabling them to be separated by up to 500
m.
The sub units have excellent environmental toughness and can be
installed very easily, enabling them to be installed over a wide area
without environmental restrictions.
(1) Setting and control of the connected input/output modules (by
means of commands from the DR230/DR240 main unit.
(2) Measured values output to the DR230/DR240 main unit.
GS 04M01D01-12E
© Copyright November 1995 (YK)
12th Edition: Feb. 2012 (KP)
<<Contents>> <<Index>>
■ Configuration
Unit configuration
Recorder main unit + sub units DS400/DS600 + Various input/output
modules + Communication interface module
The main unit of the DR240 expandable type can set and control various
input and output modules.
Component units
DR240 expandable type recorder main unit
Available module groups
You can freely configure a DR240 expandable type hybrid recorder
system for different functions by selecting modules from the following
module groups and connecting them to the main or sub units.
Input modules: Universal (DC voltage, thermocouple, RTD,
contact), DC V/TC/DI dedicated input modules,
mA, power monitor, strain, pulse, DI input.
Alarm modules: 4 channels (transfer contact) or 10 channels (make
contact) (The number of alarm channels can be
increased in module units.)
Communications modules: Select one type from GP-IB, RS-232-C,
RS-422-A/RS-485, Ethernet.
DI/DO modules: Alarm 2-point output (transfer contact) and fail/
chart end output and remote control input
modules
Extension module: For remote measurement
DS400 sub unit
b
-/B -/A
■ Package software
CH1
b
-/B -/A
CH1
CH2
b
CH2
CH3
-/B -/A
CH1
b
CH4
CH3
CH5
CH4
CH6
CH5
CH7
CH6
CH8
CH7
CH9
CH8
CH10
CH9
-/B -/A
CH1
CH2
• DARWIN DAQ 32 (Standard Package)
• DARWIN DAQ 32 Plus (Optional Package)
General
DAQ 32 and DAQ 32 Plus are software packages developed by
Yokogawa specially for the DARWIN series.
These packages run on a personal computer, achieving highly
dependable data acquisition using DARWIN series units (DA100,
DC100, DR130, DR230, and DR240) and superb operability.
The main differences between the two packages are in the
monitoring functions. The DAQ 32 only offers two display formats
- waveform trend and digital; has 2 groups of 10 channels/window;
and does not support alarm display. If simultaneous multi point
monitoring or more flexible display forms of data such as level
meter, analog meter, and thermometer faceplates, and alarm
indications are required, use the optional DAQ 32 Plus.
CH2
CH3
STATUS
CH3
CH4
CH4
CH5
CH5
CH6
CH10
SUB
CH7
CH6
CH8
CH7
CH9
CH8
CH9
CH10
UNIT
POWER
CH10
100-240
VAC
50/60Hz
70VA
MAX
DS600 sub unit
b
-/B -/A
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
b
-/B -/A
CH1
b
CH2
-/B -/A
CH1
b
CH3
CH2
-/B -/A
CH1
b
CH4
CH3
CH5
CH4
CH6
CH5
CH7
CH6
CH8
CH7
CH9
CH10
CH8
CH9
CH10
CH2
CH3
-/B -/A
CH1
CH2
STATUS
CH4
CH5
CH6
CH7
CH3
CH4
CH5
SUB
CH7
CH9
CH8
CH10
UNIT
CH6
CH8
CH9
POWER
CH10
100-240V
AC 50/6
0Hz
2
70VA
MAX
GS 04M01D01-12E
GS 04M01D01-12E
Input
Module
Sub unit
Main unit
Set-up and control
software
Personal computer
DCV
Alarm output
module
I/O module
DI/DO
module
TC
Extension
module
DAQLOGGER
RTD
Universal
DC V/TC/DI
module
DARWIN
DAQ 32 Plus
package software
Remote
measurement
DARWIN
DAQ 32
DI
module
Install
Contact Status
Power
module
AC
~
mA(current)
module
Pulse
module
Dedicated cable (up to 500 m)
Communication
interface cable
Input module
No alarm module or DI/DO module
can beconnected to theright
side of this input module.
■ DR240 Expandable type
current
A
Strain
module
PULSE
GP-IB
module
RS-232-C
module
STRAIN
RS-422-A/485
module
Communication interface module
Ethernet
module
<<Contents>> <<Index>>
3
<<Contents>> <<Index>>
■ Connecting modules
■ Standard Specifications
Main unit:
Communications modules: Select one type from GP-IB, RS-232-C,
RS-422-A/RS-485, and Ethernet.
DI/DO modules: Alarm 2-point output (transfer contact) and fail/
chart end output and remote control input
modules
Alarm output modules: 4ch or 10ch.
Connect the input modules directly to the DS400/DS600 sub unit (you
cannot connect the input modules directly to the main unit), or remotely
to the recorder main unit via sub units.
Sub unit DS400/DS600:
Input modules: Universal (DC voltage, thermocouple, RTD,
contact), DC V/TC/DI dedicated input modules,
mA, power monitor, strain, pulse, DI input.
Alarm modules: 4-point output (transfer contact) or 10-point
output (make contact) (The number of alarm
channels can be increased in module units.)
DI/DO modules: Alarm 2-point output (transfer contact), remote
control input and fail output modules
Extension module: For remote measurement
Gneral Specifications
Definition of number of connections
Main unit:
The number of input modules connected is 0.
Also, 1 communications module, 1 DI/DO
module or alarm output module can be connected.
Sub unit (DS400): The maximum number of modules per slot that
can be connected is 4.
Number of input modules + Number of DI/DO
modules + Number of alarm modules ≤ 4
Sub unit (DS600): The maximum number of modules per slot that
can be connected is 6.
Number of input modules + Number of DI/DO
modules + Number of alarm modules ≤ 6
all to common:
• The alarm output and DI/DO module must be connected on the left
side of the input modules.
• One DI/DO module can be connected to one expandable type
system.
• One extension module can be connected to one sub unit.
• The standard operating temperature and humidity are different for
each module type.
Therefore, always make sure to verify this when connecting the
module.
■ Connecting sub units
Type of sub units
DS400 sub unit: For 4 slots
DS600 sub unit: For 6 slots
Number of sub units to be connected
Construction
Panel mounting method:
DR240:
Use the mounting brackets provided.
DS400/DS600: When mounting the unit on a panel, install it
vertically on the Rack mounting.
When mounting it on the floor, widen the stand at
the bottom of the main unit so that the panel face
is vertical.
Materials:
Steel plate, aluminum alloy, plastic moldings
Paint color:
Display:
Slate gray light (equivalent to Munsell 0.1 PB 4.6/
0.2)
Core:
Lamp black (equivalent to Munsell 0.8Y2.5/0.4)
External dimensions:
Main unit:
Approx. 444 (W) × 288 (H) × 308 (D) mm
DS400 sub unit: Approx. 336 (W) × 165 (H) × 100 (D) mm
DS600 sub unit: Approx. 422 (W) × 174 (H) × 100 (D) mm
Weight:
Main unit:
Approx. 12 kg
DS400 sub unit: Approx. 2.5 kg (with 4 input/output modules
installed)
Approx. 0.9 kg*
DS600 sub unit: Approx. 3.5 kg (with 6 input/output modules
installed)
Approx. 1.1 kg*
*the weight of each unit without modules installed.
Input
Measurement range:
NOTE
Refer to “Standard connection modules” in GS 04M01E01-11E for
detailed specifications of the measurement range of each input
module.
Measurement interval:
Select an interval from 0.5, 1, 2, 3, 4, 5, 6, 10, 12, 15, 20, 30 and 60
seconds.
It depends on the minimum measurement interval of input modules
installed (when modules with different minimum intervals are
installed together, the measurement interval is determined by
whichever module has the maximum interval).
Max 300 channels/500 ms (with sub units installed)
A/D integration period:
Selectable or automatic switchover between 20 ms (50 Hz), 16.7
ms(60 Hz) and 100 ms (10 Hz)
However AUTO (automatic selection) does not function on the DC
power supply model.
Expandable type: A maximum of six sub units can be connected.
(This also applies when 4-slot sub units and 6-slot
sub units are connected to the same main unit.)
Method of connecting sub units
A sub unit can be connected to either the main unit or another sub unit
with dedicated cable.
NOTE
Refer to “Standard connection modules” in GS 04M01E01-11E for
detailed specifications of the above modules.
4
GS 04M01D01-12E
<<Contents>> <<Index>>
Recording
Recording method:
Raster scan method, 10-color wire dot recording
Number of recording points:
Measurement results: 300 points
Computation results:
60 points
Recording paper:
Ordinary recording chart, Z-fold chart (total width 342.5 mm, total
length 30 m)
Effective recording width: 250 mm (when dot-print recording)
Recording accuracy:
Dot recording: ±(0.1% of recording span + measurement
accuracy)
Digital print:
Depends on measurement accuracy.
Max recording resolution:
Dot recording: ±0.1 mm
Digital print:
Depends on measurement resolution
Recording color:
Analog trend mode
Dot recording: Purple, red, green, blue, brown, black, navy blue,
yellow-green, red-purple, orange (You can
specify a color for each channel.)
Digital printing: black
Alarm printing: Red (Alarm release mark : blue)
Logging mode
Digital printing: Purple
Recording interval:
Analog recording interval for analog trend recording
FIX:
Recording takes place at intervals of between 2
and 60 seconds (Min 2 s)
Skipped recording in case of 0.5/1 s scan
AUTO:
Linked to chart speed and measurement
interval(Min 2 s)
Digital printout interval for analog trend recording
MULTIPLE:
Specify for each channel from 6 kinds of intervals
(Specify in 1-minute intervals between 1 minute
and 24 hours.)
SINGLE:
Determined automatically from the chart speed
and the number of channels used to print digital
values.
Digital value printing interval in the logging mode:
MULTIPLE:
Specify for each channel from 6 kinds of
intervals. (Specify in 1-minute intervals between
1 minute and 24 hours.)
SINGLE:
Common to all points (Specify in 1-minute
intervals between 1 minute and 24 hours.)
Recording interval change: 2 kinds
Changes by event / action function
Chart paper feed:
Chart speed: 1 to 1500 mm/hour
Chart speed change: 2 kinds (Changes by event / action function)
Chart method: Pulse motor
Chart feed accuracy: ±0.1% of length (When recording is
performed continuously for at least 1000 mm;
Does not include elongation or shrinkage of
paper.)
GS 04M01D01-12E
Recording modes:
Normal:
Starting and stopping of recording by means of a
key operation
Alarm channel trend:
TRIGGER ... Recording starts only for the
channel in which an alarm was detected.
Recording stops when a key operation is
performed.
LEVEL ... Recording takes place only for the
channel in which an alarm was detected.
(Recording starts when the alarm is detected, and
stops when the alarm is cleared.)
Group trend:
The measurement channels are grouped, and
recording performed only for channels that belong
to the specified group. The selection of the group
to be recorded can be changed over by means of
event / action function.
printing function:
Relation between the chart speed and recording interval (analog
trend mode):
Chart speed (mm/hour) × dot recording interval
(s) must be no more than 3000.
Chart speed
1 to 9 mm/h
10 to 1500 mm/h
Channel No.
TAG
Record enabled
Record enabled
Digital print
Record disabled
Record enabled
Alarm scale
message
Record enabled
Record enabled
Recording interval for digital printout and cart speed
when the recording interval is SINGLE:
Cart speed (mm/hour) × dot recording interval
must not exceed 3000.
when the recording interval is MULTIPLE :set by timer
Number of digital print rows (Unit: hour)
Chart speed
1row
2row
3row
4row
10 to 24 mm/h
25 to 49 mm/h
50 to 99 mm/h
100 to 1500 mm/h
24
8
4
2
12
4
2
1
8
4
2
1
6
2
1
1
Time printing: Hours and minutes
Unit printing (UNIT): Can be set freely using no more than 6
characters.
Channel or TAG No. printing: 7 characters to 16 characters
selectable.
Alarm printing: Channel No., alarm kind, ON/OFF time (Hours
and minutes)
Scale value printing: 0, 100%/0, 50, 100%/every 20%
Message printing: 12 kinds of messages (16 characters) and the
time are recorded. Printing is started by a
periodic printing command, key operation, event /
action function.
5
<<Contents>> <<Index>>
Others
Recording time specification: The starting and stopping times of
recording can be set.
Manual printing: One scan’s worth of data can be digitally printed
by a key operation, remote control signal or by an
alarm status. Analog trend recording is
interrupted.
Header printing: A character string consisting of 80 characters × 5
lines is printed (it is interrupted while measured
values are being recorded). Printing is started by
a key operation, event / action function.
List printing:
The set contents are printed.
Zone recording: The recording width and recording positions (0%
and 100% positions) can be set in mm units for
each point.
Partial compression: Can be set for each channels (1 break point)
Event/Action function:
Recorning can be stared,or the chart speed
changed by alarm output status/remote control/
signal/chart end signal/timer or key operation.
Memory Function
Data Save/Load Function
Media for data save/load:
Buffer memory (internal SRAM)
Capacity:
512 Kbytes
Data backup:
Around 10 years (backup with lithium battery, at
room temperature while power is off)
Specified data length:
10, 20, 30, 40, 50, 100, 200, 300, 400, 500, 1 k,
2 k, 3 k, 4 k, 5 k, 10 k, 20 k, 30 k, 40 k, and
50 kdata/ch (Total memory lengt must be within
the free memory size.)
3.5-inch floppy disk
Number of drives: 1
Disk types: 2HD, 2DD
Supported formats:
1.2 Mbytes, 1.44 Mbytes, and 720 Kbytes
Applicable data:
Setting values, measured values, and computed values (only
possible when optional math function is specified)
The data calculated by /M3 report option can not be stored in the
buffer memory and FD.
Method to save to the floppy disk:
Copies data stored in the buffer memory to the floppy disk, except
for setting values which can be directly saved to the floppy disk.
Method to load from floppy disk:
Copies data from the floppy disk to the buffer memory except for
settin values which can be directly loaded from the floppy disk.
Printing and outputing loaded data:
Able to print captured data saved in the buffer memory or output to
a communication interface.
Data save format:
Setting values: ASCII
Measured/computed values:
binary (except ASCII (CSV Format) is also
possible when saving to floppy disk.)
6
Data capacity
Setting values:
Expandable type: Maximum about 250 kbytes (in case when saving
the setting values of an operation mode with
300ch inputs and 60ch computations.)
Measured values:
Binary data:
2 bytes/1 data
ASCII data:
12 bytes/1 data
Computed values:
Binary data:
4 bytes/1 data
ASCII data:
12 bytes/1 data
Equation to calculate the total data capacity:
Expandable type: 576 + 64 × (number of measured channel +
number of computation channel) + (number of
measured channel × 2 + number of computation
channel × 4 + 6) × specified data length
Save interval of measured/computed values:
Measurement interval of the recorder, or select from 1 min/2 min/5
min/10 min (By combining with the event/action function, it can
also sample 1 data at a time e.g. at each M.FUNC key or remote
control signal input.)
Selection of the saving method of measured/computed values
(WRITE MODE):
Direct:
Start saving the data when key operation occurs.
After saving specified length of data, stop the
saving process.
Trigger single: Start saving the data when the trigger condition is
met. After saving a specified length of data, stop
the saving process.
Trigger repeat: Start saving the data when the trigger condition is
met. Repeat the process of saving a specified
length of data to 1 file, until there is no more area
in the memory.
Trigger condition:
All Trigger conditions are configured with the event/action/
function.
Trigger condition when saving the measured/computed values:
Event/actio function (such as key operation,
remote control signal, alarm status, and chart end)
Trigger condition when loading the measured/computed values
(from buffe memory):
Event/action function (such as key operation,
remote control signal, and alarm status)
Pretrigger:
0 to 100% (can be specified in 10% intervals)
Filename when saving data:
8 ASCII characters input. However, when saving the measured/
computed values using trigger repeat, 5 ASCII characters input (last
3 letters are set automatically from 001 to 208.)
Data converion
When specify with DARWIN DAQ 32 software
File conversion: Conversion to Lotus 1-2-3 (R1A), ASCII (CSV),
Excel (Ver. 4.0).
Range of Conversion: specify for data points.
GS 04M01D01-12E
<<Contents>> <<Index>>
Display function
Display section:
Display:
VFD display (5 × 7 dot matrix, 3 rows)
Number of characters:
22 characters (large/1 row), 40 small characters (2
rows)
Displayed contents:
Digital value display:
Data for freely selected channels can be displayed
on each line (1 channel per line, max 5 rows).
The CH/TAG No. (7 characters), and also the
alarm status, measured value and unit for each
channel are displayed simultaneously.
Measured value bar graph display:
The data is displayed as 0 to 100% in the
specified lines.
Auxiliary data: Clock, alarm status, alarm relay status, battery
consumption, record ON/OFF, key lock ON/OFF,
recorder operation (print format)
Alarms
Number of settings:
Up to four settings can be made for each channel.
Kinds of alarms: Selection from higher limit, lower limit, difference
higher limit, difference lower limit, higher limit of
rate of change, lower limit of rate of change
However, only upper limit and lower limit alarms
are output for totalized results.
Rate of change alarm time interval: Can be set to measurement
interval × 1 to 15 (Common to both rising and
falling limits.)
Output mode:
Excitation/non-excitation selection, AND/OR mode selection, and
output hold/non-hold specification can be made. (common to all
channels)
A maximum of 6 reflash alarm output points can be specified.
Number of alarm output points:
DR240 main unit:0 points.Alarm modules can not be connected to
the DR240 main unit.
DS400/DS600: The alarm points are increased in module units.
By increasing the number of subuits.
Alarm data recording:
Analog Trend mode:
The channel number, kind of alarm and ON/OFF
time (hours and minutes) are printed in the right
margin.
Logging mode: The kind of alarm is printed when the measured
data are recorded.
Display alarm data:
Alarm status indication:
When an alarm is detected, the status indicator
lights. The indicator can also be made to flash
depending on the setting.
Alarm acknowledge indication:
The alarm indicator stops flashing when a key
operation is performed.
Standard computation functions
Kinds of computation:
Difference between arbitrarily selected channels, linear scaling
(scaling), moving average
GS 04M01D01-12E
Linear scaling:
Scalable range: DC voltage, thermocouple, RTD, contact
Scaling range: –30000 to +30000
Decimal point: Arbitrarily set
Measurement accuracy for scaling:
Measurement accuracy for scaling (digits) =
Measurement accuracy (digits) × Scaling span
(digits)/Measurement span (digits) + 2 digits
(Numbers below the decimal point are rounded up.)
Moving average:
The moving average results for between 2 to 64 scans are
computed.
Fail, chart end output
Fail output:
Outline of functions:
If an abnormality is found in the main unit of the
recorder, the fail output terminal is de-energized.
Contact mode: A contact (normally open and common terminal)
Can be switched between excited and nonexcited.
Contact capacity: 250 VDC/0.1 A (resistive load)
30 VDC/2 A (resistive load)
250 VAC/2 A (resistive load)
Withstanding voltage:
Between the output terminal and ground 2300
VAC (50/60 Hz) for 1 minute
Chart end output:
Outline of functions:
The chart end output terminal is energized if the
recording paper in the recorder breaks.
Contact mode: A contact (normally open and common terminal)
Can be switched between excited and nonexcited.
Contact capacity: 250 VDC/0.1 A (resistive load)
30 VDC/2 A (resistive load)
250 VAC/2 A (resistive load)
Withstanding voltage:
Between the output terminal and ground 2300
VAC (50/60 Hz) for 1 minute
Power supply section
Rated supply voltage:
AC power supply :100 to 240 VAC (free supply
voltage selection)
DC power supply : 12 to 28 VDC (only for the
subunit (DS400/DS600) of a DC power supply
model)
Usable supply voltage range:
AC power supply :90 to 250 VAC
DC power supply : 10 to 32 VDC (only for the
subunit (DS400/DS600) of a DC power supply
model)
Rated supply frequency:
50/60 Hz
Power consumption:
DR240 main unit ... Max approx. 130 VA
DS400 sub unit ... Max approx. 55 VA (when 4
connectable input/output modules are installed)
max. approx. 25 VA (DC power supply)
DS600 sub unit ... Max approx. 70 VA (when 6
connectable input/output modules are installed),
max. approx. 25 VA (DC power supply)
7
<<Contents>> <<Index>>
Others
Clock:
With calendar function (Western calendar)
Clock accuracy: ±100 ppm. However, this does not include the
delay (less than 1 second) caused when the power
is switched ON and OFF once.
System fault alarm: Contact output
Set value backup: Lithium battery backup (approx. 10 years at
ambient temperature of 23°C), excluding clock
function
Key Lock: Software setting
Insulation resistance:
At least 20 MΩ between the power supply and
ground, between each terminal and ground, and
between each input terminal (measured with 500
VDC)
Withstand voltage:
Between the input terminals and the DR230 main
unit ground
1500 VAC (50/60 Hz) for 1 minute
Between the output terminals and the DR230
main unit ground
2300 VAC (50/60 Hz) for 1 minute
Between AC power supply terminals and the
DR240 main unit ground
1500 VAC (50/60 Hz) for 1 minute
Between AC power supply terminals and the
DS400 sub unit ground
1500 VAC (50/60 Hz) for 1 minute
Between AC power supply terminals and the
DS600 sub unit ground
1500 VAC (50/60 Hz) for 1 minute
Normal Operation Conditions
Supply voltage: 90 to 250 VAC
Supply frequency: 50 Hz ± 2%, 60 Hz ± 2%
Ambient temperature:
DR242 main unit
When panel-mounted : 0 to 50°C
When Floppy disk operation : 5 to 40°C
DS400/DS600 sub unit
When floor-mounted and Desk-top : 0 to 50°C
When panel-mounted : –10 to 60°C
When Rack-mounted : 0 to 50°C
Ambient humidity:
Temperature
Humidity
0 to 40°C
20 to 80% RH
40 to 50°C
10 to 50% RH
DS400
–10 to 40°C
20 to 80% RH
DS600
40 to 50°C
10 to 50% RH
subunit
50 to 60°C
5 to 30% RH
DR242
main unit
* no ice formation
Vibration:
Shock:
Magnetic field:
Position:
Warmup time:
8
10 to 60 Hz 0.2 m/s2
Not allowed
400 A/m max (50/60 Hz)
The unit should be mounted left-right horizontally
or vertically, as a general rule.
At least 30 minutes after switch-on.
Installation location: Room
Installation height:
Altitude up to 2,000 m
Installation category:
II (according to CSA22.2 No.1010.1)
Measurement category:
II (according to IEC61010-1)
Degree of pollution: 2
Standard Performance
Measurement and recording accuracy
Measurement accuracy:
Standard operation state:
23 ± 2°C, 55 ± 10% RH, supply voltage: 90 to
250 VAC, supply frequency: 50/60 ± 1%,
Warmup: At least 30 minutes; When operating,
the system must not adversely affect the operation
of other measuring instruments by generating
vibration, for example.
NOTE
Refer to “Standard connection modules for the DR230/DR240
hybrid recorder” in GS 04M01E01-11E for detailed specifications
of the measurement accuracy.
Effect of Operation Conditions
Ambient temperature:
Variation for a temperature change of 10°C
within ±(0.1% of rdg + 1 digit)
±(0.2% of span + 1 digit) for Cu 10 Ω
Voltage variation:
Within ±1 digit over the range of 90 to 132, or
180 to 250 VAC (frequency 50/60 Hz)
External magnetic field:
Variation with respect to AC (50/60 Hz) and DC
magnetic fields of 400 A/m ... Within ± (0.1% of
rdg + 10 digits)
Radio wave:
Within ±(1% of span) at 1 m from 150 MHz or
460 MHz field
Signal source resistance:
Variation with respect to signal source resistance
+ 1 kΩ change
(1) Voltage 2 V range or below ... Within ±10 µV
6 V range or above ... Within ±0.1% of rdg
(2) Thermocouple
Within ±10 µV; However, it must be within ±100
µ when burnout is specified.
(3) RTD
Variation with respect to change of 10 Ω per wire
(when all three wires are the same resistance
value)
Indication ... Within ±(0.1% of rdg + 1 digit)
Variation in indication with respect to a
difference of 40 MΩ in the resistance
between conductors (max difference between
3 wires) ... Approx. 0.1°C
Mounting position:
Variation when the unit is mounted horizontally
on a panel ... Within ±(0.1% of rdg + 1 digit)
excluding RJC error
Vibration:
Variation when sinusoidal vibration of acceleration 0.2 m/s2 is applied for 2 hours in each of the
3 axial directions over a frequency range of 10 to
60 Hz ... Within ±(0.1% of rdg + 1 digit)
GS 04M01D01-12E
<<Contents>> <<Index>>
Transportation and Storage Conditions
■ Optional specifications
Number of channels for computing (Number of channels that can
be allocated for computational purposes.):
Stand-alone type: 30ch maximum
Expandable type: 60ch maximum
Computation interval:
Every measurement interval (except when the computation
becomes too difficult to be processed every measured interval, in
which case an alarm is generated)
Significant digits during computation:
±1038
Significant digits of the computed result:
–9999999 to +99999999 (Decimal point can be set to have 1 to 4
digits on the right of the decimal point)
Input from communication interface:
Digital value (ASCII numerical array) input from the
communication interface can be handled as computational data
Computation start/stop:
Can be controlled by communication commands, M.FUNC key
operation, and event/action function (such as M.FUNC key
operation, remote control signal, time specified, and alarm status)
Other functions included in the math function:
Remote RJC
Input type:
Thermocouple (TC)
Accuracy:
(Twice the measurement accuracy of the standard
thermocouple input) + (temperature difference
between the terminal of the remote terminal
section and thermocouple section for measuring
the remote terminal temperature)
Thermocouple burnout: not selectable
Optional specifications must be specified using the type number code.
They cannot be specified for the DS400 or DS600 sub unit.
/M3: Report Function
These refer to the environmental conditions existing during transportation and storage from the time of shipment from the factory until
commencement of use, and also during transportation and storage in the
case of a temporary period of non-use.
If the environmental conditions are maintained within the specified
range, the unit will not incur permanent damage, and can be returned to
a normal working condition (re-adjustment may be required in some
cases).
Ambient temperature: –25 to 60°C
Humidity:
5 to 95% RH
Vibration:
10 to 60 Hz 4.9 m/s2 max
Shock:
392 m/s2 max (in packed condition)
Supported standards
CSA
UL
CE
C-Tick
Obtained CSA22.2 No.1010.1,
Installation category (Overvoltage category): II,
Degree of pollution: 2
Obtained UL3111-1 (CSA NRTL/C)
EMC directive EN61326
EN61000-3-2
EN61000-3-3
EN55011 Class A Group 1
Low voltage
EN61010-1
directive
Measurement category: II,
Degree of pollution: 2
AS/NZS 2064 Class A Group 1
/H1: Internal Illumination
Clear internal illumination for easy distinction of traces.
/D2: Deg. F Display function
This function converts measured data into °F, and displays it on the
display monitor of a DR.
/M1: MATH Function
Computation types:
Types:
Four arithmetical operations, SQR (square root),
ABS (absolute value), LOG (common logarithm),
LN (natural logarithm), EXP (exponent),
statistical computation*, logical computation
(AND, OR, NOT, and XOR), relational
computation, exponentiation, previouslymeasured value reference, hold**, reset, clear,
and remote RJC.
*Statistical computation
CLOG:
Computation process of simultaneously measured
values within a group (total, maximum, minimum,
average, and maximum - minimum)
TLOG:
Computation process of a specific channel over
time axis (total, maximum, minimum, average,
and maximum - minimum)
Statistical computation interval:
Set by the event/action function
**Temporary hold of the computed result
Can be controlled by event/action function (such as key operation,
remote control signal, time specified, and alarm status).
GS 04M01D01-12E
Refer to the GS 04M01B01-31E
Outline:
This function assigns measurement and/or computation channels as
report channels, and creates statistical information. The report
computation can be selected from an hourly, daily, or monthly
report. Chart printing takes place automatically whenever the report
creation time (in the case of the DR recorder) is reached. The
results of report computation can also be output by communication.
Kinds of report computations:
Hourly report: Statistical information for one hour (starting on
the hour)
Daily report:
Statistical information for one day (starting from a
reference time)
Monthly report: Statistical information for one month (starting
from a reference date and time)
Each of the hourly, daily, and monthly reports can be set to ON or
OFF.
NOTE
The data calulated by this option can not be stored in the buffer
memory and FD of the DR recorders.
/L1: Winter/Summer Time
Winter and summer time can be set.
9
<<Contents>> <<Index>>
■ Type name and specification code
Main unit
Model
DR242
Suffix Code
Memory
-0
-1
Optional Code
Description
250 mm, panel mount hybrid recorder
No memory device
3.5” FD
Software
0
2
No DARWIN DAQ 32 software
DARWIN DAQ 32 software (English) specify
No. of Inputs
-00
Power Supply
Power Inlet
Always-00
100 VAC to 240 VAC
-1
W
Optional Features
/M1
/M3
Screw terminal, without cord
Math function (including RRJC)
Report function
/H1
/L1
/D2
Internal illumination
Winter/Summer time
Deg. F display
/FC
DARWIN DAQ 32 is supplied with floppy disks
Subunit DS400/DS600
Model
DS400
DS600
Type
Description
Optional Code
Suffix Code
4 slots subunit for inputs and alarm output
6 slots subunit for inputs and alarm output
Always-00
100 VAC to 240 VAC
-00
Power Supply
-1
-2
Power Inlet & Power Cable
D
F
H
R
S
W
Y
12 VDC to 24 VDC (DC power supply only)
3-pin power inlet w/UL, CSA cable
3-pin power inlet w/VDE cable
3-pin power inlet w/CCC cable
3-pin power inlet w/SAA cable
3-pin power inlet w/BS cable
3-pin power inlet w/screw terminal
2-pin inlet with round-type connector
(when power supply suffix code is -2)
Input module
Model Code
DU100-11
DU100-21
DU100-31
DU100-12
DU100-22
DU100-32
DU200-11
DU200-21
DU200-31
DU200-12
DU200-22
DU200-32
DU300-11
DU300-12
DU400-12
DU400-22
DU500-12
DU500-13
DU500-14
DU600-11
DU700-11
10
Description
10ch universal input module (DCV/TC/DI & RTD)
20ch universal input module (DCV/TC/DI & RTD)
30ch universal input module (DCV/TC/DI & RTD)
10ch universal input module (DCV/TC/DI & RTD)
20ch universal input module (DCV/TC/DI & RTD)
30ch universal input module (DCV/TC/DI & RTD)
10ch DCV/TC/DI input module
20ch DCV/TC/DI input module
30ch DCV/TC/DI input module
10ch DCV/TC/DI input module
20ch DCV/TC/DI input module
30ch DCV/TC/DI input module
10ch mA input module
10ch mA input module
Power monitor module for single phase
Power monitor module for 3 phase
10ch strain input module (120 Ω)
10ch strain input module (350 Ω)
10ch strain input module (External bridge box)
10ch pulse input module
10ch DI input module
Terminal
Screw
Screw
Screw
Clamp
Clamp
Clamp
Screw
Screw
Screw
Clamp
Clamp
Clamp
Screw
Clamp
Clamp
Clamp
Clamp
Clamp
NDIS
Screw
Screw
GS 04M01D01-12E
<<Contents>> <<Index>>
Other module
Model Code
DT100-11
2 alarm, 12 remote, fail/chart end
DT200-11
DT200-21
4 alarm relay output (transfer contacts)
10 alarm relay output (make contacts)
DT300-11
DT300-21
GP-IB interface module
RS-232-C interface module
DT300-31
DT300-41
RS-422-A/RS-485 interface module
Ethernet interface module
Description
Screw terminal
Screw terminal
Screw terminal
Accessories
Model Code
DV100-011
Description
DV100-012
DV200-000
DV200-001
Extension module
Extension base unit
Extension cable (0.5 m)
Extension cable (1 m)
DV200-002
DC200-005
DV200-010
Extension cable (2 m)
Extension cable (5 m)
Extension cable (10 m)
DV200-020
DV200-050
DV200-100
DV200-200
Extension cable (20 m)
Extension cable (50 m)
Extension cable (100 m)
Extension cable (200 m)
Extension cable (300 m)
Extension cable (400 m)
Extension cable (500 m)
Cable adapter
Shunt resistor 10 Ω for screw input terminal
Shunt resistor 10 Ω for clamped input terminal
DV200-300
DV200-400
DV200-500
DV250-001
DV300-011
DV300-012
DV300-101
DV300-102
DV300-251
DV300-252
DV400-011
DV400-012
DV400-051
DV450-001
Shunt resistor 100 Ω for screw input terminal
Shunt resistor 100 Ω for clamped input terminal
Shunt resistor 250 Ω for screw input terminal
Shunt resistor 250 Ω for clamped input terminal
Rack mount kit (DA100 exp./DS400) for ANSI
Rack mount kit (DA100 stand./DS600) for ANSI
Power cable: Supplies Subunit with the power form the DR extension model
DIN-NDIS strain conversion cable
Package software
Model Code
DP120-13
WX102/CD1
WX101/CD1
GS 04M01D01-12E
Description
DARWIN DAQ 32 software (Windows XP/Vista/7) (comes standard)
DARWIN DAQ 32 Plus software (Windows 2000/XP/Vista/7) (optional)
DAQLOGGER for multi-channel data logging software (Windows 2000/XP/Vista/7) (optional)
11
<<Contents>> <<Index>>
■ Dimensions
unit: mm
Panel cutting dimensions
At least 520
281
At least 80
424
425+20
40
203
64.8
280
288
444
■ Rear panel (Name of parts)
Vacant slot with cover
(for communication interface, alarm, or DI/DO modules)
Failure output terminals
Chart end output terminals
Power fuse(located in the main unit)
Heat sink fins
AC outlet(Auxiliary
for DS400/DS600)
Power terminals with a cover
Function grounding
terminal
12
GS 04M01D01-12E
<<Contents>> <<Index>>
Subunit DS400
20
115
145
unit: mm
290
336
320
100
22
40
50
165
50
8
145
20
115
Subunit DS600
369
100
422
156
162
22
20
176
168
55
If not specified, the tolerance is ±3%, However, in cases of less than 10 mm, the tolerance is ±0.3 mm.
GS 04M01D01-12E
13
<<Contents>> <<Index>>
■ Names of Parts
Subunit DS400
Module connector
Lid covering the extension
cable connector
Switch to set the
unit number
Status indicator
Screw holes for
module installation
Installation holes
Power switch
Function grounding
terminal (below power switch)
Power connector
Feet
Holes for fastening the feet
Subunit DS600
Installation
holes
Module
connector
Lid covering the
extension cable
connector
Screw holes for
module installation
Status indicator
Switch to set
the unit number
Power switch
Function grounding
terminal (below power switch)
Feet
Power connector
Holes for fastening
the feet
Rack Mount fitting (ANSI/EIA)
14
6.8
14.7
177
101.6
6.8
unit: mm
482.6
453.2
37.7
37.7
177
101.6
14.7
482.6
453.2
GS 04M01D01-12E
<<Contents>> <<Index>>
Location and Location Number (Channel Number, Alarm Output Relay Number, DI/DO Number)
The location numbers correspond to channel numbers for locations where the input module is connected, to alarm output numbers for locations where
the alarm module is connected, and to DI/DO numbers for locations where the DI/DO module is connected.
Modules are mounted on a unit in slots. The number of each module is the same as that of the slot.
As shown below, input/output location numbers are assigned related to the unit number (the main unit number is fixed at I) and module location.
Module 0 (Location numbers:I01 to I10)
Main unit DR242
Input modules cannot be
connected.
Unit No.:I
Module 5 (Location numbers:051 to 060)
Module 4 (Location numbers:041 to 050)
Module 3 (Location numbers:031 to 040)
Module 2 (Location numbers:021 to 030)
Module 1 (Location numbers:011 to 020)
Module 0 (Location numbers:001 to 010)
Subunit DS600
Unit No.:0
Module 3 (Location numbers:131 to 140)
Module 2 (Location numbers:121 to 130)
Module 1 (Location numbers:111 to 120)
Module 0 (Location numbers:101 to 110)
Subunit DS400
Unit No.:1
Note
When the following handling is done, it is necessary to carry out “system construction” to operate the instrument
correctly. After executing system construction, confirm the module information.
· Connection (including addition or replacement)/removal of subunits, or unit number setting
· Mounting (including addition or replacement)/removal of modules
GS 04M01D01-12E
15
<<Contents>> <<Index>>
Wiring Input Signal Lines (to Universal and DCV/TC/DI input modules)
Terminals
Screw type terminal
b
-
+
B
A
Clamp type terminal
DC voltage • TC •
contact
RTD*
CH1
CH2
*There are no RTD
input terminals on
the DCV/TC/DI input
module.
A +
B b
CH2
CH10
CH1
CH4
CH3
CH10
CH9
Wiring Diagram
DC voltage input/DI input (contact)
+
DC input
-
+
+
DC voltage input
-
TC input
-
+
DC current input
-
RTD input
b
B
+
Shunt resistor
Note:For 4 to 20 mA input, shunt
resistance value should
be 250 Ω ± 0.1%
A
A
b
B
Compensation lead
10 Ω* max./leadwire
Three wire resistances
should be approx. equal.
*10 Ω max. for Pt 100 Ω and
Pt 50 Ω, 1 Ω max. for Cu 10 Ω.
Wiring Output Signal and Remote Control Signal Lines (to DI/DO and Alarm modules)
Terminals
NO C NC
DT100-11
Terminal arrangement
Failure output (transfer-contact)
Chart end output (transfer-contact)
Remote control signal input
(12 contact terminals)
1
2
ALM output
(transfer-contact)
NO C NC
DT200-11
DT200-21
NO C
NO C NC
FAIL ● ● ●
NO C NC
● ●
CHART ●
REM
1
●
C
●
2
●
3
●
C
●
4
●
5
●
C
●
6
●
7
●
C
●
8
●
9
●
C
●
10
●
11
●
C
●
12
●
NO C NC
ALM1 ● ● ●
NO C NC
ALM2 ● ● ●
1 Alarm output
2 (transfer contact)
1
2
Alarm
output
(make
contact)
3
4
Alarm output
(transfer contact)
10
Output contact rating: 250 VDC/0.1 A (resistive load), 250 VAC/2 A (resistive load), 30 VDC/2 A (resistive load)
16
Subject to change without notice.
GS 04M01D01-12E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising