HDMI 1.3 Extender SET over Single CAT5 User Guide - AV-iQ

HDMI 1.3 Extender SET over Single CAT5 User Guide - AV-iQ
HDMI 1.3 Extender over Signal CAT5E/6 Cable
with 3D, IR & RS232 bi-directional Control
Model #: HDM3D-C5IR-SET
© 2012 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products
including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.
www.avenview.com
1
Table of Contents
Section 1: Getting Started ...................................................................................................................... 3
1.1
Important Safeguards ............................................................................................................ 3
1.2
Safety Instructions ................................................................................................................. 3
1.3
Regulatory Notices Federal Communications Commission (FCC) ......................................... 4
Section 2: Introduction........................................................................................................................... 4
2.1
Package Contents................................................................................................................... 6
2.2
Before Installation.................................................................................................................. 6
2.3
Panel Description ................................................................................................................... 7
2.4
Installation ............................................................................................................................. 9
2.5
Auto EDID Learning .............................................................................................................. 10
Section 3: General Troubleshooting..................................................................................................... 10
3.1
General Troubleshooting ..................................................................................................... 11
Section 4: Specifications....................................................................................................................... 12
4.1
PIN & Wiring Standard Definition ........................................................................................ 14
4.2
PIN & Wiring Standard Definition ........................................................................................ 14
4.3
Accessories........................................................................................................................... 15
www.avenview.com
2
Section 1: Getting Started
1.1
Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover


Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
 Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized
product modification, or failure to follow instructions supplied with the product.
 Repair or attempted repair by anyone not authorized by us.
 Any damage of the product due to shipment.
 Removal or installation of the product.
 Causes external to the product, such as electric power fluctuation or failure.
 Use of supplies or parts not meeting our specifications.
 Normal wear and tear.
 Any other causes which does not relate to a product defect.

1.2
Removal, installation, and set-up service charges.
Safety Instructions
The HDM3D-C5IR-SET, HDMI 1.3a Extender over Signal CAT5 with 3D, IR and RS232 Control has been tested
for conformance to safety regulations and requirements, and has been certified for international use.
However, like all electronic equipment, the HDM3D-C5IR-SET should be used with care. Read the following
safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.




Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards


Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.


www.avenview.com
3
1.3
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
Section 2: Introduction
The Avenview HDM3D-C5IR-SET HDMI extender over single CAT5E/6 with 3D, IR and RS232
bi-directional control as well as Auto EDID Learning extends your video/audio transmission distance up to
60m (200ft) in HDTV 1080i format, 40m (130ft) in HDTV 1080p format, and 20m (65ft) in HDTV 1080p with
36-bit color depth. HDM3D-C5IR-SET also supports the most advanced 3D video format and therefore
guarantees the highest 3D video compatibility on the market. With only one cost effective Cat.5/5e/6 cable,
users can readily extend HDTV sources from DVD players, Blu-ray Disc player, PS3, PC, and any other kinds of
sources compliant with TMDS to distant display monitors including HDMI or DVI enabled TV sets or LCD PC
monitors. With the advanced design for the latest HDMI technology, deep color video, DTS-HD Master Audio
or Dolby TrueHD audio, and HDCP supports and compatibility are all supported. This flexibility makes HDCP
compliant DVD players or PS3 transmit utmost high quality video and audio with a greater distance at the
minimal cost, when integrating several components apart. In addition, HDM3D-C5IR-SET is also equipped with
bi-directional IR pass-through path and RS-232 serial port control. These bonus features allows users to boost
IR control distance up to 100m (330 ft) and makes IR control possible through only single Cat.5/5e/6 cable
including HDMI signals. In addition, serial port offers the convenient path for interactive application, such as
touch panels.
The HDM3D-C5IR-SET includes two units: transmitting unit HDM3D-C5IR-S and receiving unit
HDM3D-C5IR-R. The transmitting unit is used to capture the input HDMI / DVI signals with IR control packets
and carry the signals via one cost effective Cat5e/6 cable. The receiving unit is responsible for equalizing the
transmitted HDMI signal and reconstructing IR and serial control signals. The transmission distance between
the sending and receiving units can be up to 60m (200ft) at HD 720p or 1080i; or 40m (130ft) at Full HD 1080p.
With an 8-level equalization rotary control on the receiving unit, users can adjust the equalization strength to
the received HDMI signals accordingly, and therefore optimize the transmission distance between source and
destination.
www.avenview.com
4
-
Support HDMI Deep Color & full 3D
Extends the transmission up to 60m (200ft) from the HDMI source at HD 1080i or 720p 24-bit
Extends the transmission up to 40m (130ft) from the HDMI source at Full HD 1080p 24-bit
Extends the transmission up to 20m (65ft) from the HDMI source at Full HD 1080p 36-bit
HDCP 1.1 compliant
Auto EDID feature
Minimizes the cable skew by adjustable 8-level equalization control
Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6 cable transmission
DTS-HD and Dolby TrueHD high bit rate audio support
Supports full frequency IR signal from 20KHz to 60KHz
Bi-directional IR path
Full Duplex RS-232 control up to 115,200 bps through connector
Allows cascading
Wall mounting housing design for easy and robust installation
Perfectly integrated with other HDMI over CAT5 series products
The claimed transmission distance here is subject to the grade of installed cable(s), source device
and display. For over CAT5/6transmission, the cable(s) has to be solid, not stranded. Any
keystone jack along the transmission path will kill the transmission performance significantly!
The IR and RS-232 function can NOT be used at the same time.
www.avenview.com
5
2.1
Package Contents
Before you start the installation of the converter, please check the package contents.
-
HDM3D-C5IR-S
HDM3D-C5IR-R
Power Adapter
x1
x1
x2
-
User’s Manual
x1
IR Blaster
x1
IR Receiver
x1
2.2




Before Installation
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications (DC5V 2A). If inappropriate power supply is
used then it may cause a fire.
Do not twist or pull by force ends of the UTP cable. It can cause malfunction.
www.avenview.com
6
2.3
Panel Description
FRONT PANEL & REAR PANEL (Transmitter, HDM3D-C5IR-S)
1
2
3
4
5
6
7
8
1. MODE: Rotary dial A-H for video transmission (See
Table Below)
5. IR BLASTER: Infrared 3.5mm socket for plugging in
the extension cable of IR blaster
2. DIP SWITCH: Setup the RS-232 mode for serial
communication channel
6. RS-232: Connect to PC Serial Port with a D-SUB-9
male-male cable here
3. HDMI IN: Connects to a HDMI source with a HDMI
male-male cable
7. +5V DC: Connect to 5V DC power supply.
4. IR RECEIVER: Infrared 3.5mm socket for plugging
in the extension cable of IR receiver
8. HDMI SIGANL OUT: Plug in a Cat-5E/6 cable that
needs to be linked to the receiving unit
MODE on Transmitter
A
VIDEO
B
VIDEO
C
VIDEO
D
VIDEO
E
VIDEO
F
VIDEO
G
VIDEO
H
EDID Learning
EDID Full-HD([email protected])
- 24bit 2D video
EDID Full-HD([email protected])
- 24bit 2D video
EDID Full-HD([email protected])
- 24bit 3D video
EDID Full-HD([email protected])
- 24bit 3D video
EDID HD([email protected])([email protected])
([email protected]) - 24bit 2D video
EDID HD([email protected])([email protected])
([email protected]) - 24bit 2D video
EDID Full-HD([email protected])
- 36bit 2D video
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
Supports up to 7.1 Channel
Output
Locks to Stereo Audio Output
Supports up to 7.1 Channel
Output
Locks to Stereo Audio Output
Supports up to 7.1 Channel
Output
Locks to Stereo Audio Output
Locks to 7.1 Channel Audio
Output
Auto EDID learning
www.avenview.com
7
FRONT PANEL & REAR PANEL (Receiver- HDM3D-C5IR-R)
1
2
3
4
6
5
1. Signal Level: Adjust the 8-level equalization
control to the received HDMI signals
7
8
5. IR BLASTER: Infrared 3.5mm socket for plugging in
the extension cable of IR blaster
2. DIP SWITCH: Setup the RS-232 mode for serial
communication channel
6. RS-232: Connect to PC Serial Port with a D-SUB-9
male-male cable here
3. HDMI OUT: Connects to a HDMI display with a
HDMI male-male cable
7. +5V DC: Connect to 5V DC power supply.
4. IR RECEIVER: Infrared 3.5mm socket for plugging
in the extension cable of IR receiver
8. HDMI SIGANL IN: Plug in a Cat-5E/6 cable that
needs to be linked to the receiving unit
SIGNAL LEVEL on the HDM3D-C5IR-R (Receiver)
*SIGNAL LEVEL:
Adjust the 8-level equalization control to the received HDMI signals. The HDMI signal level varies from
MIN (weakest) and Max (strongest) for respective transmission length from longest possible range to
short distance. Please adjust the signal level from MIN to MAX and stop turning the rotary switch
whenever the audio/video is playing normally. Inappropriate signal level setting may cause overpowering
issue that would shorten the product life significantly!
If a flickering or a blinking image is seen, try to adjust the rotational switch to improve the cable
skew. Max stands for the strongest EQ while MIN stands for the weakest. Try adjusting the EQ from
MIN to MAX
www.avenview.com
8
DIP SWITCH (Straight or Crossover Mode)
DIP Switch
Description
Position
TX & RX
nd
ON []
TxD: The 2 pin of RS-232, which is in charge
of (receiving data
)
rd
RxD: The 3 pin of RS-232, which is in charge
of (sending data
)
OFF []
TxD: The 3 pin of RS-232, which is in charge
of (receiving data
)
nd
RxD: The 2 pin of RS-232, which is in charge
of (sending data )
rd
2.4
Installation
To setup Avenview HDM3D-C5IR-SET follow these steps for connecting to a device:
1.
Connect your HDMI/DVI source (such as a Blu-ray Disc player) to Transmitter (HDM3D-C5IR-S).
2.
Connect your HDMI/DVI display (such as a LCD TV) to the receiving unit HDM3D-C5IR-R.
3.
Connect your CAT-5E/6 LAN cable between the transmitting and receiving units.
4.
Make sure CAT-5E/6 LAN cable is tightly connected and not loose.
5.
Plug in 5V DC power cord to the power jack of the receiving unit HDM3D-C5IR-R.
6.
Plug in 5V DC power cord to the power jack of the transmitting unit HDM3D-C5IR-S.
www.avenview.com
9
2.5
Auto EDID Learning
To learn EDID from the monitor/TV following these steps
1.
2.
3.
4.
Connect HDM3D-C5IR-R and the desired display through a HDMI cable and then connect
HDM3D-C5IR-S and the video source through a HDMI cable as well.
Turn on both the HDM3D-C5IR-S and the HDM3D-C5IR-R.
Set the Mode of HDM3D-C5IR-S to “H,” and wait for 3-5 seconds.
The device could learn the EDID of the desired display via HDM3D-C5IR-R after the step “3,”and enjoy
the experience; the users DO NOT need to power cycle again or even twice while plugging on
different displays.
When adjusting the EQ level on the receiver unit. Please dial the rotary control switch from MIN to
MAX and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate
EQ level setting may cause overpowering issue that would shorten the product life significantly!
Section 3: General Troubleshooting
Problem
Possible Solution
No Image





Screen Defects
Appear
Check if connection to the source and the display are correct.
Ensure that display device supports 480p, 720p and 1080p resolution
This product supports up to 1080p (1920x1200) resolution.
Check the DVI and HDMI connection
If outputting from a PC. Check the maximum resolution range of the
graphics card.
www.avenview.com
10
3.1
-
General Troubleshooting
Wrongly inserting the IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the
failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective
IR sockets.
-
If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve
and provide DVI or HDMI display EDID information.
-
All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP
cable and ASTRODESIGN Video Signal Generator VG-859C & VG-870B.
-
The transmission length is largely affected by the type of Cat-5E/6 cables, the type of HDMI sources,
and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m
[1,000ft] bulk cables) can transmit a lot longer signals than stranded UTP cables (usually in the form
of fixed length patch cords). Shielded STP cables are better suited than unshielded UTP cables. A solid
UTP Cat-5e cable shows longer transmission range than stranded STP Cat-6 cable. For long extension
applications, solid UTP/STP cables are the only viable choice.
-
EIA/TIA-568-B termination (T568B) for Cat-5E/6 cables is recommended for better performance.
-
To reduce the interference among the unshielded twisted pairs of wires in Cat-5E/6 cable, one can
use shielded STP cables to improve EMI problems, which is worsen in long transmission.
-
Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can
achieve and how good is the received picture quality, the actual transmission range is subject to one's
choice of Cat-5E/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat-6 cable is
-
recommended.
If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI input #1]
generally can produce better transmission performance among all HDMI inputs
www.avenview.com
11
Section 4: Specifications
Item
Description
Units
Unit Description
HDMI Compliance
HDM3D-C5IR-S
HDM3D-C5IR-R
HDMI 1.3a with 3D Transmitter
HDMI 1.3a with 3D Receiver
High Speed HDMI Deep Colour & Full 3D Support
HDCP Compliance
Video Bandwidth
Supported Resolutions
Resolution and Distance
(24-bit)
Audio Support
Equalization
Input TMDS Signal
Input DDC Signal
Yes
Single Link 225 MHz (6.75Gbps)
480i / 480p / 720p / 1080i / 1080p60
Full HD: (1080p)-40meter (130feet) (CAT5e) / 50meter (165feet) (CAT6)
HD: (720p/1080i)-50meter (165feet) (CAT5e) / 60meter (200feet) (CAT6)
Surround Sound (up to 7.1 Ch) or Stereo Digital Audio
8 Level Digital Control at Rx
1.2 Volts (peak-to-peak)
5 Volts (peak-to-peak, TTL)
Human body model — ±15kV (air-gap discharge) & ±8kV (contact discharge)
Core chipset — ±8kV
Full-duplex bi-directional
Yes
1x HDMI + 1x 3.5mm
1x RJ45 + 1x 3.5mm
1x RJ45 + 1x 3.5mm
1x HDMI + 1x 3.5mm
ESD Protection
IR Pass-thru
RS-232 Support
Input
Output
IN/OUT
HDMI Connector
HDMI Source Control
IR Remote Control
RJ45 Connector
3.5mm Connector
Rotary Switch
-
1x DIN9
1x DIN9
Type A (19 pin female)
Controllable via IR pass-through from RX to TX and from TX to RX with IR extenders
Electro-optical characteristics:  = 25° / Carrier frequency: 20-60kHz
WE/SS 8P8C with 2 LED indicators
IR blaster & IR receiver
EDID Mode selection
www.avenview.com
Signal level equalization
12
Environmental
Operating Temperature
Storage Temperature
Relative Humidity
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (no condensation)
Housing
Metal enclosure
Model
Dimensions
[L x W x H] Package
Carton
71 x 91 x 35mm [2.8" x 3.6" x 1.4"]
270 x 175 x 80mm [10.6" x 6.9" x 3.1"]
450 x 370 x 300mm [1'6" x 1'3" x 11.8"]
Model
Weight
239g [8.4oz]
Package
Fixedness
1000g [2.2 lbs]
Wall-mounting case with screws
Power supply
5V 2A DC
Power consumption
1.5 Watts
Operation temperature
0~40°C [32~104°F]
Storage temperature
-20~60°C [-4~140°F]
Relative humidity
20~90% RH [no condensation]
Performance Guide for HDMI over Category Cable Transmission
Performance rating
Wiring
Solid
Stranded
Shielding
Type of category cable
CAT5
CAT5e
CAT6
Unshielded (UTP)



Shielded (STP)



Unshielded (UTP)



Shielded (STP)



Termination
Please use EIA/TIA-568-B termination (T568B) at any time
www.avenview.com
13
4.1
PIN & Wiring Standard Definition
Type A (Receptacle) HDMI
4.2
Pin 1
TMDS Data2+
Pin 11
TMDS Clock Shield
Pin 2
TMDS Data2 Shield
Pin 12
TMDS Clock–
Pin 3
TMDS Data2–
Pin 13
CEC
Pin 4
TMDS Data1+
Pin 14
Reserved (N.C. on device)
Pin 5
TMDS Data1 Shield
Pin 15
SCL
Pin 6
TMDS Data1–
Pin 16
SDA
Pin 7
TMDS Data0+
Pin 17
DDC/CEC Ground
Pin 8
TMDS Data0 Shield
Pin 18
+5V Power
Pin 9
TMDS Data0–
Pin 19
Hot Plug Detect
Pin 10
TMDS Clock+
PIN & Wiring Standard Definition
www.avenview.com
14
4.3
Accessories
IR Extenders
IR Blaster
IR Receiver
IR Sockets
IR BLASTER: plug in the IR blaster to emit all IR command signals received from the IR receiver from the other
end to control the devices corresponding to the IR signals.
IR RECEIVER: plug in the IR receiver to receive all IR command signals from the IR remote controls of the
corresponding devices.
Definition of IR 3.5mm Jack
IR Blaster
IR Receiver
Generic IR cables that are available in the market place can be used only if they are compatible to the
definition of the IR sockets for the matrix if necessary for replacement use. However, IR cables longer
than 2m (6-ft) may not work
www.avenview.com
15
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the
operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of
Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of
anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the
Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability,
function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and
non-infringement.
www.avenview.com
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement