MIO SDI- AViewer User Manual
MIO SDI-AViewer
User Manual V1.3
www.gefei-tech.com
[Gefei Tech.Co.,Ltd]
Copyright
Copyright © 2009 Gefei Tech. Co., Ltd All rights reserved. This document may not be copied in
whole or in part.
Trademarks
Gefei-Tech,Magi,MIO,VIO,XIO,MVS,MRS are either registered trademarks or trademarks of
Gefei Tech. Co., Ltd in China and/or other countries. Other trademarks used in this document are
either registered trademarks or trademarks of the manufacturers or vendors of the associated
products.
Disclaimer
Product options and specifications subject can be changed without notice. The information in this
manual is furnished for informational use only, is subject to change without notice, and should not
be construed as a commitment by Gefei Tech. Co., Ltd. Gefei Tech. Co., Ltd assumes no
responsibility or liability for any errors or inaccuracies that may appear in this publication.
Revision Status
Rev Date
Description
October 13, 2011
Initial release of the MIO HDSDI-HDMI/DVI User Manual
WEB Software V4.0
2012-8-31
Initial release of the MIO HDSDI-HDMI/DVI User Manual
WEB Software V4.1
2013-4-7
Initial release of the MIO SDI- AViewer User Manual
WEB Software V1.1
2013-10-14
Initial release of the MIO SDI- AViewer User Manual
WEB Software V1.3
Table of Contents
Product Description......................................................................................................................... 1
Features ........................................................................................................................................... 1
Panel Description ............................................................................................................................ 2
Left Panel ................................................................................................................................... 2
Right Panel ................................................................................................................................. 2
Buttons Definition...................................................................................................................... 3
Application........................................................................................................................................ 4
Special Notice .................................................................................................................................. 5
How to Use the Remote Control Software ................................................................................... 6
Attention before use ................................................................................................................... 6
Introduction of Web Control ........................................................................................................ 6
Function overview ............................................................................................................. 6
Audio & Video .................................................................................................................... 7
Input Source ............................................................................................................... 7
Output resolution ...................................................................................................... 8
Video Display Mode ................................................................................................... 8
Color parameters ....................................................................................................... 9
Audio to HDMI ........................................................................................................... 9
OSD parameters .............................................................................................................. 10
Audio meter display................................................................................................. 10
Editable program UMD ............................................................................................ 11
Attach UMD and Audio meters to edge ................................................................... 13
Transparency of Audio meters and UMD ................................................................. 13
Tally /GPI Display ..................................................................................................... 14
AFD Display.............................................................................................................. 15
Safe Marker .............................................................................................................. 15
Input Format ............................................................................................................ 16
Waveform Display.................................................................................................... 17
Disable OSD (Full screen) ......................................................................................... 18
Layout management ............................................................................................... 18
Alarm Settings ................................................................................................................. 20
Audio Detection ...................................................................................................... 20
Video Detection....................................................................................................... 22
Status of Video and Audio ............................................................................................... 23
User Configuration .......................................................................................................... 24
Network Configuration ................................................................................................... 25
Change IP address.................................................................................................... 25
Change manager IP for SNMP Management........................................................... 25
Check boxes of necessary items for SNMP .............................................................. 26
Upgrade firmware of system ................................................................................... 26
Specifications ................................................................................................................................. 28
Contact Us...................................................................................................................................... 31
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Product Description
Based on Mini BOX platform, MIO SDI- AViewer is a high-quality video and audio
converter which can convert one 3G/HD/SD-SDI signal to DVI or HDMI signal for digital
display devices, such as LCD, DLP, and Plasma. It is the ideal ways to monitor digital
signal.
MIO SDI- AViewer can be controlled by Ethernet network via IE browser, which is
convenient to configure the display parameters. The device provides various output
resolut ions and audio and video detection, such as signal loss, signal freeze, audio
silence and so on. The text of UMD program can be edited freely. And it supports SNMP,
which is easy to manage the device.
Although the device adopts DVI output interface, the HDMI signal can be obtained by
using a DVI to HDMI adapter or cable. In HDMI mode, the HD/SD audio are embedded
into HDMI signal.
Features
 Automatic input detection of 525i 60, 625i 50, 720p, 1080i, and 1080p format of
HD/SD signal
 Various output resolutions up to 1920x1080px60
 In HDMI mode, the HD/SD audio are embedded into HDMI signal
 Provide audio and video monitoring and alarm, such as signal loss, signal freeze,
audio silence and so on
 Display program UMD and 8 channels audio, and adjust transparency of them
freely

Provide various waveforms, such as illumination waveform, PbPr waveform, audio
waveform and so on
 Build-in web server to control the device with user-friendly interface
 Adjust luminance, saturation, contrast and de-noise freely
 Provide on-screen display: input formats, AFD and safe marker
 Supports SNMP
Gefei Tech. Co., Ltd
1 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
 Mini box structure easily installed inside frame racks, video walls and so on
 Widely used in broadcasting system, studios and other professional fields
Panel Description
Left Panel
PWR: Power indicator, the indicator shows green as the power is working normally.
IN: Signal indicator, the indicator shows green as the video is locked with no errors.
SDI IN: BNC interface, digital video signal input (support H D/SD-SDI with embedded
audio)
Support input formats as below
480i 60, 576i 50
720p 50/59.94/60
1080i 50/59.94/60
1080P 24/25/30
1080P 50/59.94/60
SDI-Loop: BNC interface, support loop out of input with power on.
Right Panel
DC IN: Standard power, 12V, 1A
Gefei Tech. Co., Ltd
2 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
HDMI/DVI-OUT: Via DVI-I interface (female) to output DVI-D and HDMI signal.
Although the device adopts DVI output interface, the HDMI signal can
be obtained by using a DVI to HDMI adapter or cable. In HDMI mode,
the SDI audio signals are embedded into HDMI signal.
The output resolution can be configured as below.
1024x768x60p, 1280x720x50p/60p
1280x768x60p, 1280x800x60p
1280x1024x60p, 1360x768x60p
1400x1050x60p, 1600x900x60p
1680x1050x60p, 1920x1080x50i/60i
1920x1080x50p/60p, AUTO HDMI
(AUTO HDMI: auto-match the output resolution based on EDID detection of monitors.)
Note: Via web server, user can select the audio channels from HD/SD-SDI signal to
embed into CH1&CH2 of HDMI output signal. See the function details about Audio
output.
Network: RJ45 interface with 10/100/1000M auto-detection. And the default IP address
is 192.168.1.76. The web server is remote control interface.
Buttons Definition
Resolution/ Default
Restart
Resolution/ Default: Using a push pin to short press the button, the output resolut ion
is changed among 1280x720x60p、1920x1080x60p and AUTO
Gefei Tech. Co., Ltd
3 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
HDMI. Using a push pin to long press the button until the DVI
output disappears. The parameters on the web page will be
restored to default ones, including IP address and user password.
The default IP address is 192.168.1.76, and default password is
000000 (six zeros).
Restart: Using a push pin to press the button, The function of the button equals to turn
off. Probably around 5s, the power to restart .
Application
Gefei Tech. Co., Ltd
4 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Special Notice
1. In order to avoid network traffic congestion, please do not submit parameters before
the first modification is applied.
2.In order to avoid hardware loose contact caused by continuous operations on the
front panel, please do your second operation after you have got the first operation
result.
3. Generally, it will spend about three seconds to get the results after you submit. The
time is related with the monitor type. If the time is too long (over 7seconds), maybe
there is something abnormal with the hardware’s working status (overheating for
example), please wait pat iently.
4.Do not plug the DVI connector without power-down.
5. When there is no display output from the device on the monitor, maybe the output
resolut ion don’t match the monitor. Please try to change the output resolution
though web server.
6.Windows 2003, Windows XP and Windows Vista are strongly recommended with
Internet Explorer.exe.
7. Build-in Web server to control Mini box easily by your computer via Ethernet. Please
make sure IP address of Mini box is in the same network segment as your computer.
And the IP and Mac address of Mini box are unique value in Ethernet.
8. User can also upgrade system under the label “Network”. Before the upgrade, the
anti-virus software and firewall have to be closed to make sure that the upgrade data
is transmitted to MIO SDI- AViewer system without rejection. Power and network
cannot be cut off during upgrading.
Gefei Tech. Co., Ltd
5 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
How to Use the Remote Control Software
Attention before use
MIO SDI- AViewer has a built-in Web server, so user could configure it by Internet
Explorer easily when connecting it through cable.
The default IP address: 192.168.1.76.
The default user name: admin
The default password: 000000 (six zeros)
Introduction of Web Control
You do not need to install the client software. Open the IE, and input the IP address in
the location bar to open the user interface. Default IP address is “http://192.168.1.76”.
Input user name (admin) and init ial password (000000). Click “login”, you will enter into
the actual operation remote control.
Function overview
There are many labels at the top of the web page: Audio & Video, OSD, Alarm, Status,
User, Network, and Help. Different functions can be achieved under different labels.
Audio & Video: Configuration of input source, output resolution, display mode, color
parameters, and HDMI embedded audio.
OSD: Configuration of UMD display, Audio meters, AFD information display, Safe
Marker, Waveform, and Layout management.
Alarm: The system supplies detection of audio, mute, frame frozen, black, signal loss.
Each alarm threshold can set to meet your needs.
Gefei Tech. Co., Ltd
6 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Status: Show the current status of video and audio.
Network: Configuration of IP address and parameters for SNMP management, and
upgrade the firmware.
Help: Show the versions of each firmware here.
Audio & Video
Input Source
You can choose input source between Cable and Fiber. So far, only the type of BNC
cable is available.
Gefei Tech. Co., Ltd
7 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Output resolution
HDMI output interface provides EDID detection from the monitor. And the resolutions
from EDID are highlighted in the dropdown list. See the picture shown above. The
output resolution of HDMI signal is up to 1920x1080x60p.
The output resolution can be configured as below.
1024x768x60p, 1280x720x50p/60p
1280x768x60p, 1280x800x60p
1280x1024x60p, 1360x768x60p
1400x1050x60p, 1600x900x60p
1680x1050x60p, 1920x1080x50i/60i
1920x1080x50p/60p, AUTO HDMI
(AUTO HDMI: auto-match the output resolution based on EDID detection of monitors.)
Video Display Mode
There are two types of video display: Full channel and Original Ratio.
Full channel means the video image will cover the entire window and ignore the aspect
ratio of video signal.
Gefei Tech. Co., Ltd
8 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Original Ratio means the video image always keeps the aspect ratio of video signal. So
for SD input signal, the aspect ratio of video image is 4:3;And for HD input signal, it is
16:9.
Color parameters
Brightness: to set the brightness or darkness of picture. The range is from -512 to 511.
Saturation: to set the color of picture. The range is from 0 to 511.
Contrast: to adjust the clarity of picture. The range is from 0 to 511.
Put the mouse on the cursor and drag it to the assigned position; or you can fill in the
certain value ranging from 0 to 255, and then press “Enter” on keyboard.
Reset button: to restore the factory default settings. The default value of brightness,
saturation and contrast is zero.
Audio to HDMI
Select audio channels from HD/SD-SDI to embed into HDMI signal. It supports eight
audio channels for HDMI signal.
The drop-down list is shown as following.
Off/ CH1&2/ CH3&4/ CH5&6/ CH7&8
“Off” option means no audio signal is embedded into the selected channels of HDMI
signal.
Gefei Tech. Co., Ltd
9 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
OSD parameters
Here you can adjust various parameters for On-screen Display, such as UMD, Audio
meters and so on.
Audio meter display
Audio meter monitoring
System provides four groups of audio meters to monitoring up to eight audio channels
from HD/SD-SDI signal. Each group can show two audio channels and be configured
individually.
The drop-down list is shown as following.
Off/ CH1&2/ CH3&4/ CH5&6/ CH7&8
“Off” option means the selected audio meters are turned off and not displayed on
screen.
The position of audio meters
Both Sides: AM1 and AM2 are located on the left side of screen, while AM3 and AM4 are
located on the right side of screen. If there are only AM1 and AM2 (or AM3
and AM4) displayed on the screen, so AM1 (AM3) is on the left side and AM2
(AM4) on the right side.
Left Side: AM1, AM2, AM3, and AM4 are all located on the left side of screen.
Right Side: AM1、AM2、AM3、AM4 are all located on the right side of screen.
Gefei Tech. Co., Ltd
10 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Editable program UMD
First, select the needed channel in the drop-down list. The system supports the single
programmable UMD display. Two kinds of UMD mode are provided. They are static
UMD via text upload and dynamic UMD via TSL protocol.
1)
Static UMD: Choose “Network” in the drop-down list, and click “Settings”.
Upload UMD Text
Type the characters in blank bar, change color of characters, and preview the UMD
effect real time. Click “OK” after all parameters are settled and all characters will be
displayed in UMD.
Clear UMD Text
Delete all characters or enter a “space”, and then click “OK”, the character in UMD area
will be cleared.
2)
Dynamic UMD: Choose “TSL” in the drop-down list and click “Settings”.
Gefei Tech. Co., Ltd
11 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Dynamic UMD of MIO SDI-AViewer is achieved by Ethernet. Support the TSL/IP V4.0
protocol
Here are a few steps to achieve dynamic UMD:
First, set the TSL port on Network page to be the same as the ones of TSL Tallyman.
The default value is 163. Enter the new port value in the blank area, click “OK”, and
then restart the unit. After it goes back to work, the new TSL port value takes effect.
The same as control
device, such as TSL
Tallyman Do restart
the unit after
changing port value.
Second, Check the box “TSL” on OSD page
Gefei Tech. Co., Ltd
12 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Third, set the target address for selected channel to receive the data from TSL Tallyman.
Please make sure there is no same target address for the channels, that is, each target
address has unique value for each channel.
Upload UMD picture
UMD picture can be changed to user-defined one freely through this function.
The picture that you need to upload must be 32bits TGA format with Alpha channel.
The size of picture is 720x60 pixels
Check/ uncheck UMD
Check the box “UMD”. It will be shown within the channel, otherwise, not.
Attach UMD and Audio meters to edge
Check the box, UMD bar and audio meters are attached to the edge of screen which
makes the video image be shown completely. If not, UMD bar and audio meters are
overlaid on the image.
Transparency of Audio meters and UMD
In this area, users can modify the transparency of audio meters and UMD. Put the
mouse on the cursor and drag it to the assigned position; or you can fill in the certain
value ranging from 0 to 100, and then press “Enter” on keyboard. “0” stands for full
transparency and “100” stands for opacity.
Gefei Tech. Co., Ltd
13 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Tally /GPI Display
This function is reserved so far. Tally and Dynamic Tally.
1)
Choose “None” in the drop-down list
The Tally function is disabled and Tally turns gray.
2)
Via GPI-Static Tally
The function is reserved.
3)
Via Ethernet-Dynamic Tally
Choose “TSL ” in the drop-down list
The dynamic Tally is the same as dynamic UMD. Support the TSL/IP V4.0 protocol
Here are a few steps to achieve dynamic UMD:
First, set the TSL port on Network page to be the same as the ones of TSL Tallyman.
The default value is 163. Enter the new port value in the blank area, click “OK”, and
then restart the unit. After it goes back to work, the new TSL port value takes effect.
Second, Check the box “TSL” on OSD page
Third, set the target address for selected channel to receive the data from TSL Tallyman.
Please make sure there is no same target address for the channels, that is, each target
address has unique value for each channel.
Gefei Tech. Co., Ltd
14 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
AFD Display
Check the box and AFD information will be overlaid on the top of the screen, otherwise,
not. AFD information is shown in the form of picture, according to the AFD code inside
of input signal.
AFD
Picture
Safe Marker
Safe Area Mode
The picture of SD-SDI signal is marked with 16:9 safe area markers, and the picture of
HD-SDI signal is marked with 4:3 safe area markers.
Line: Marker showed with lines
Gefei Tech. Co., Ltd
Mask: block the image with Mark
15 / 29
MIO SDI- AViewer User Manual V1.3
Mask & Line: Apply both mode
Gefei-tech
None: No safe marker on the screen
Transparency of Safe Area
Adjust transparency value of Mark. The image can be blocked more or less by this
adjustment.
Put the mouse on the cursor and drag it to the assigned position; or you can fill in the
certain value ranging from 0 to 100, and then press “Enter” on keyboard. “0” stands for
full transparency and “100” stands for opacity.
Input Format
Check the box, and input resolution/format will be overlaid on the top of the screen,
otherwise, not.
1080i 60
Input
Resolution
Gefei Tech. Co., Ltd
16 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Waveform Display
Choose Waveform Mode
System supports display of real-time waveform and vector overlaid on image. There
are three opt ions in drop-down list. They are “None”, “Y+PbPr+Vector”, and “Y+Audio
Waveform/Phase”.
Y+PbPr+Vector
Y Waveform
PbPr Waveform
Vector
Y+Audio Waveform/Phase
Y Waveform
Audio Waveform of two
channels
Audio Phase of two
channels
None: No waveform on the screen
Gefei Tech. Co., Ltd
17 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Select audio channels for Audio Measure
In the mode of “Y+Audio Waveform/Phase”, Audio Waveform and Phase are based on
the audio channels you selected from HD/SD-SDI signal.
The drop-down list is shown as following.
Off/ CH1&2/ CH3&4/ CH5&6/ CH7&8
Adjust transparency of Waveform Background
Adjust transparency value of Waveform Background. The image can be blocked more
or less by this adjustment.
Put the mouse on the cursor and drag it to the assigned position; or you can fill in the
certain value ranging from 0 to 100, and then press “Enter” on keyboard. “0” stands for
full transparency and “255” stands for opacity.
Disable OSD (Full screen)
Check the box, on-screen-display elements all disappear, so the image is displaying in
the full screen mode.
Uncheck the box, the checked elements appear on the screen. Meanwhile, the status of
each on-screen-display element can be set individually.
Layout management
All configured parameters can be saved as a template. System provides up to four
templates for quick application of different occasions.
Gefei Tech. Co., Ltd
18 / 29
MIO SDI- AViewer User Manual V1.3
HD Studio
Gefei-tech
Edit name of template in the blank bar.
Press “Save” button to submit data.
Click one of four buttons, for example, click “Template 1”. Here is a message box
appearing. Enter the name of template in the blank area on the top of message box,
and click “Save” button on the bottom. So the name of the button is changed to the
one you edited, not “Template 1” any more.
You can change the name of template which
has been saved, then press “save” button.
Show status of each
parameter of the
saved template
Apply the template
Delete the template
Click the template which is saved already, and a message box appears to show the
status of its each parameter. You can apply the template, or delete the template. After
you change its parameters, even its name, press “Save” button to submit the new data.
Gefei Tech. Co., Ltd
19 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Apply: Click this button to apply the relevant parameters.
Delete: Click this button to delete the relevant parameters.
Alarm Settings
: Check all the boxes for detect ion settings of selected channels
: Cancel all the checks for detect ion settings of selected channels
: Restore Factory Setting
The video and audio signal can report signal status and validity, with detection of:
(1) Video lose
(4) Audio overload
(2) Video black
(3) Video frozen
(5) Audio in silence
Audio Detection
Measure unit of digital audio is dBFS(dB Full Scale). 0dBFS is the maximum audio level,
corresponding to +24dBu of analog audio.
Gefei Tech. Co., Ltd
20 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Audio Overload
It will prompt an alarm as soon as the audio level overloads the threshold you have
settled. It provides 8 audio channels detect ion. And there is a box in front of each audio
channel. This detection will take effect only the box is checked. The threshold and
duration of detection can be configured for detect ion of each audio channel. The
threshold means a maximum audio level. When actual volume is above this threshold,
the system will prompt alarm of audio overload.
Audio in Silence
It will prompt an alarm picture as soon as the audio level lowers the threshold you
settled. It provides 8 audio channels detect ion. And there is a box in front of each audio
channel. This detection takes effect only if the box is checked. The threshold and
duration of detection can be configured for detect ion of each audio channel. The
threshold means a minimum audio level. When actual volume is below this threshold,
the system will prompt alarm of audio in silence.
Gefei Tech. Co., Ltd
21 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Video Detection
Loss of Signal
It prompts an alarm picture as soon as signal is lost. This detection takes effect only if
the box is checked.
Video Frozen
It will prompt an alarm picture as soon as the regular pixels ratio of the image is lower
the threshold you have settled. This detection will take effect only if the box is checked.
The threshold and duration of detection can be configured. The threshold means the
frozen pixel percentage in one frame.
Video Black
It will prompt an alarm picture as soon as video level is lower the threshold. This
detection will take effect only if the box is checked. The duration of detection can be
configured.
Gefei Tech. Co., Ltd
22 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Status of Video and Audio
Video status
Show input format and input type of signal source, current output resolution and EDID
detection of monitor.
Audio status
System supports status auto-detection of each audio channel of input source. If audio
value of one channel is above -70dBfs, the status of the audio channel is existed marked
as “Yes”. If audio value of one channel is below -70dBfs, the status of the audio channel
is mute marked as “None”
So far, audio G1 and G2 of input source can be detected, and G3 and G4 are not.
Gefei Tech. Co., Ltd
23 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
User Configuration
The software provides password-protected function. Default user name is admin, and
default password is 000000 (Six zeros). Users can modify the password; maximum
password length is 12 bits. When you modify the password successfully, information
will prompt as "The password is altered successfully. It will take effect when you login
next time."
Gefei Tech. Co., Ltd
24 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Network Configuration
Change IP address
User can modify the IP address. If modified successfully, the system appears a message
box telling the operation successful. Then restart the device, enter the new IP address
in IE address and the web software will be opened.
Change manager IP for SNMP Management
Configure the “Manager IP” to be the local IP address of SNMP Server. The Server and
MIO mini box should be in the same network segment. And Trap common and Trap port
are for SNMP. Do not change them.
Gefei Tech. Co., Ltd
25 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Check boxes of necessary items for SNMP
Check/Uncheck the box of each item to enable/disable the SNMP trap.
If check the box of “SNMP”, each item below can be check or uncheck individually, that
is, each trap can be enabled or disabled individually. Otherwise, if uncheck the box of
“SNMP”, the system will disable all trap items for SNMP management at the same
time.
Upgrade firmware of system
User can also upgrade system under this label. Before the upgrade, the anti-virus
software and firewall have to be closed to make sure that the upgrade data is
transmitted to Mini box without rejection. Windows 2003, Windows XP, Windows Vista
and Windows 7 system are strongly recommended to upgrade the system with Internet
Explorer.exe.
There are two items for upgrading, main DSP and font, if there is new version released,
we will upgrade file to the customs. Power and network cannot be cut off during
upgrading. When system is upgraded successfully, please turn off the power and restart
Gefei Tech. Co., Ltd
26 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
the device again. It takes about 5 minutes to upgrade main DSP or font.
Gefei Tech. Co., Ltd
27 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Specifications
Video Input
Input interface:
1* BNC connector
Impedance:
75 ohms
Format:
480i 60, 576i 50
720p 50/59.94/60
1080i 50/59.94/60
1080p24/25/30
1080P 50/59.94/60
HDSDI Loop
Output interface: 1*HD/SD-LOOP, BNC connection
Impedance:
75Ω
Format:
SMPTE 259M-C;270Mb/s
SMPTE-292M;1.485Gps
SMPTE-425;2.970Gps
Eye pattern:
800mV±10%
Rise time:
750~1500PS (20%-80%)
Fall time:
750~1500PS (20%-80%)
The difference between rise and fall:
Jitter:
≤500PS
<0.2UI
DVI Output
Interface:1*DVI-I (Female / DVI-D and HDMI signal)
Output resolution: changeable via Web server
1024x768x60p, 1280x720x50p/60p, 1280x768x60p
1280x800x60p, 1280x1024x60p, 1360x768x60p
1400x1050x60p, 1600x900x60p, 1680x1050x60p
1920x1080x50i/60i, 1920x1080x50p/60p, AUTO HDMI (EDID)
Gefei Tech. Co., Ltd
28 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Ethernet Control
1 x RJ45, 10/100/1000M adaptive
Status Indicator
Input signal status indicator
Power indicator
(Indicate by shining or extinguishing of the green LED)
Dimension
120x98x27mm
Power
12V 1A
Gefei Tech. Co., Ltd
29 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
PACKING LIST
PO No.
CUSTOMER:
CARRIER:Gefei Tech.Co.,Ltd
TO
Device List
Name
Specification
Quantity
MIO HD SDI-HDMI/DVI
HD-SDI TO DVI-D/HDMI Converter
1
AC-DC Power
90~260VAC TO 12VDC 1A
1
Total
Remark
2
Accessories List
Name
Specification
Quantity
Video Cable
-----------
-----------
Audio Cable
-----------
-----------
Power Cable
-----------
-----------
User’s Manual (or Disk)
Others
1
DVI-D TO HDMI Converter
1
Total
Gefei Tech. Co., Ltd
Remark
2
30 / 29
MIO SDI- AViewer User Manual V1.3
Gefei-tech
Contact Us
Technical support:
Tel:010-58858188
Fax:010-58858189
Website
www.gefei-tech.com
E-mail:swang@gefei-tech.com
Address:
Gefei Tech. Co., Ltd
A-603 Power Creative Plaza NO.1 Shangdi E.Rd.Haidian District Beijing 100085
To Find More information, please visit www.gefei-tech.com
Gefei Tech. Co., Ltd
31 / 29
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising