Quick Start Guide
Quick Start Guide
ESUG4P-PG2-D*
Introduction
Welcome to KBC Network’s Quick Start Guide for
the ESUG4P-PG2, 6 port, PoE switch. This
document provides some quick tips on how to
get up and running. For more detailed
information see the Downloads section below.
Industrial Ethernet Switch
System Contents
Equipment Required for Physical
Deployment
Qty Description
1
Ethernet switch fitted with DIN rail mount.
2
Wall-mount brackets with screws.
1
Pluggable terminal block.
You will need a 50 - 57Vdc power supply, these
are supplied separately.
Features:
•
•
•
•
•
•
IEEE802.3at on 4 ports
Dual redundant power input
Alarm output for power supply
Full & half duplex operation
MDI/MDI-X
IP30 casing
Downloads
Installation manual
Other features and functions are described in the
unabridged manual:
http://www.kbcnetworks.com/esug4p-pg2series/network-products/esug4p-pg2-series
Specification sheet:
http://www.kbcnetworks.com/esug4p-pg2series/network-products/esug4p-pg2-series
QSG_ESUG4P-PG2-Rev1112
Copyright © KBC Networks Ltd. 2011
www.kbcnetworks.com
Quick Start Guide
ESUG4P-PG2-D*
Configuring the ESUG4P-PG2-D*
1.
2.
3.
Connect the DIN rail or wall-mount
brackets as required.
Connect a 50 - 57Vdc power supply,
(supplied separately).
If using only one power source, connect
pin 1 to pin 5 and pin 2 to pin 6 otherwise
the Power Fail LED will be lit.
Industrial Ethernet Switch
ESUG4P-PG2-D* LED Status Indicators
LED
Status
PWR1
ON
Power is supplied to the unit
Need Help/Troubleshooting?
OFF
No power to the unit
ON
Power is supplied to the unit
Visit our website http://www.kbcnetworks.com or
contact your nearest KBC office or dealer:
OFF
No power to the unit
ON
Power to PWR1 or PWR2 has
failed
OFF
Power is functioning to both or
none of the power inputs.
ON
The port is supplying power to
the powered device.
OFF
There is no powered device
attached or the power
ON
SFP port link established
PWR2
P-Fail
PoE 1-4
P5 & P6
4.
5.
6.
Install SFP modules as required.
Link external devices to the switch with
appropriate cables.
Connect the fault alarm contact if required.
Description
FLASH
Active data flow
OFF
No connection to the network
APAC:
Phone: +65 98463323
Email: apactechsupport@kbcnetworks.com
EMEA:
Phone: +44(0)1622 618787
Email: emeatechsupport@kbcnetworks.com
USA:
Phone: +1 949-297-4930
Toll Free: +1 888-366-4276
Email: techsupport@kbcnetworks.com
Ethernet RJ45 Port P1 – P4 Status LED
Each RJ45 Ethernet port has two indicators. The lower
green lamp indicates port speed, and the upper green
lamp indicates port link state.
Lower
ON
Full duplex link
FLASH Collisions are occurring
Upper
OFF
Half duplex link or no connection
ON
Effective network connection has
been established for the port
FLASH Data traffic is passing through
the port
OFF
QSG_ESUG4P-PG2-Rev1112
Copyright © KBC Networks Ltd. 2011
No effective network connection
has been established for the port
www.kbcnetworks.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising