Engineering Data and Installation Manual

Engineering Data and Installation Manual
Engineering Data and
Installation Manual
XT MODELS PACKAGED WATER-TO-AIR MULTI-POSITIONAL HEAT PUMPS
REVISION:A
*20D082-01NN*
20D082-01NN
Table of Contents:
Section 1: Model Nomenclature
Model Nomenclature......................................................................................................................4
Section 2: Installation Introduction
Introduction, Inspection, Unit Protection, Pre-Installation, Components.............................5 - 6
Section 3: Installation Considerations
Consumer Instructions, DIY Policy, Installation, Electrical. Thermostat, Loop Pumps,
Desuperheater Package and Piping, UV Light Usage................................................................7
Section 4: Installation
Unit Placement, Pre-Installation Checklist....................................................................................8
Unit Dimensional Data....................................................................................................................9
Unit Physical Data..........................................................................................................................10
Unit Conversion..............................................................................................................................11
Ductwork Installation..............................................................................................................12 - 13
Section 5: Unit Piping Installation
Open Loop, Interior Piping, Water Quality...........................................................................14 - 18
Section 6: Antifreeze
Overview.........................................................................................................................................19
Antifreeze Charging...............................................................................................................20 - 21
Section 7: Desuperheater Installation
Installation................................................................................................................................22 - 24
Section 8: Controls
Controls & Wiring Diagrams...................................................................................................25 - 32
Section 9: Accessories
Auxiliary Electric Heat...................................................................................................................33
APSMA Pump Sharing Module......................................................................................................34
Section 10: Equipment Start-Up Procedures
Equipment Start-Up Checklist......................................................................................................35
Equipment Start-Up Form.............................................................................................................36
Section 11: Troubleshooting
Troubleshooting., Superheat/Subcooling Conditions, Troubleshooting Form..................38 - 42
Section 12: Engineering and AHRI Data
Unit Electrical Data.................................................................................................................43 - 44
Water Flow and Heating/Cooling Calculations, Corrections Factor...............................45 - 46
AHRI and Full Load Extended Data Tables..........................................................................47 - 67
Section 13:
Revision Table.................................................................................................................................68
Section 1: Model Nomenclature
-
Enertech Global
4
XT Models, Rev.: A
Section 2: Installation Introduction
INTRODUCTION:
This geothermal heat pump provides heating
and cooling as well as optional domestic water
heating capability. Engineering and quality
control is built into every geothermal unit. Good
performance depends on proper application
and correct installation.
equivalent protective covering. Cap or recap
unit connections and all piping until unit is
installed. Precautions must be taken to avoid
physical damage and contamination which
may prevent proper start-up and may result in
costly equipment repair.
⚠ CAUTION ⚠
Notices, Cautions, Warnings, & Dangers
“NOTICE” Notification of installation, operation
or maintenance information which is important,
but which is NOT hazard-related.
DO NOT OPERATE THE GEOTHERMAL
HEAT PUMP UNIT DURING BUILDING
CONSTRUCTION PHASE.
“CAUTION” Indicates a potentially hazardous
situation or an unsafe practice which, if not
avoided, COULD result in minor or moderate
injury or product or property damage.
Storage:
All geothermal units should be stored inside in
the original packaging in a clean, dry location.
Units should be stored in an upright position
at all times. Units should not be stacked unless
specially noted on the packaging.
“WARNING” Indicates potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
Pre-Installation:
Special care should be taken in locating
the geothermal unit. Installation location
chosen should include adequate service
clearance around the unit. All vertical units
should be placed on a formed plastic air
pad, or a high density, closed cell polystyrene
pad slightly larger than the base of the unit.
Flex connectors should also be installed in
between the ductwork and the unit. All units
should be located in an indoor area where
the ambient temperature will remain above
55°F and should be located in a way that
piping and ductwork or other permanently
installed fixtures do not have to be removed
for servicing and filter replacement.
“DANGER” Indicates an immediate hazardous
situation which, if not avoided, WILL result in
death or serious injury.
Inspection:
Upon receipt of any geothermal equipment,
carefully check the shipment against the
packing slip and the freight company bill of
lading. Verify that all units and packages have
been received. Inspect the packaging of
each package and each unit for damages.
Insure that the carrier makes proper notation
of all damages or shortage on all bill of lading
papers. Concealed damage should be
reported to the freight company within 15 days.
If not filed within 15 days the freight company
can deny all claims.
Pre-Installation Steps:
Note: Notify Enertech Global’s shipping
department of all damages within 15 days. It
is the responsibility of the purchaser to file all
necessary claims with the freight company.
1.
2.
Unit Protection:
Protect units from damage and contamination
due to plastering (spraying), painting and
all other foreign materials that may be used
at the job site. Keep all units covered on the
job site with either the original packaging or
XT Models, Rev.: A
5
Compare the electrical data on the unit
nameplate with packing slip and ordering
information to verify that the correct unit
has been shipped.
Remove any packaging used to support or
hold the blower during shipping. Remove
and discard the blower motor armature
shaft shipping bracket from the rear of the
blower.
Enertech Global
Section 2: Installation Introduction
3.
4.
5.
Components:
Inspect all electrical connections
and wires. Connections must be clean and
tight at the terminals, and wires should not
touch any sharp edges or copper pipe.
Verify that all refrigerant tubing is free of
dents and kinks. Refrigerant tubing should
not be touching other unit components.
Before unit start-up, read all manuals and
become familiar with unit components
and operation. Thoroughly check the unit
before operating.
Master Contactor: Energizes Compressor
and optional Hydronic Pump and/or
Desuperheater package.
Logic Board: Logic Board operates the
compressor and protects unit by locking out
when safety switches are engaged. It also
provides fault indicator(s).
Terminal Strip: Provides connection to the
thermostat or other accessories to the low
voltage circuit.
Transformer: Converts incoming (source)
voltage to 24V AC.
Low Voltage Breaker: Attached directly to
transformer, protects the transformer and low
voltage circuit.
⚠ CAUTION ⚠
Reversing Valve: Controls the cycle of the
refrigerant system (heating or cooling).
Energized in cooling mode.
ALL GEOTHERMAL EQUIPMENT IS
DESIGNED FOR INDOOR INSTALLATION
ONLY. DO NOT INSTALL OR STORE UNIT
IN A CORROSIVE ENVIRONMENT OR IN
A LOCATION WHERE TEMPERATURE AND
HUMIDITY ARE SUBJECT TO EXTREMES.
EQUIPMENT IS NOT CERTIFIED FOR
OUTDOOR APPLICATIONS. SUCH
INSTALLATION WILL VOID
ALL WARRANTIES.
High Pressure Switch: Protects the refrigerant
system from high refrigerant pressure, by locking
unit out if pressure exceeds setting.
Low Pressure Switch: Protects the refrigerant
system from low suction pressure, if suction
pressure falls below setting.
Flow Switch (Freeze Protection Device): Protects
the water heat exchanger from freezing,
by shutting down compressor if water flow
decreases.
⚠ WARNING ⚠
FAILURE TO FOLLOW THIS CAUTION MAY
RESULT IN PERSONAL INJURY. USE CARE
AND WEAR APPROPRIATE PROTECTIVE
CLOTHING, SAFETY GLASSES AND
PROTECTIVE GLOVES WHEN SERVICING
UNIT AND HANDLING PARTS.
Electric Heater: Provides auxiliary heat during
cold temperatures and provides electric
backup if unit malfunctions.
Blower Motor (ECM): ECM (Electrically
Communicated Motor) for variable fan speeds.
⚠ CAUTION ⚠
Compressor (Copeland Scroll): Pumps
refrigerant through the heat exchangers and
pressurizes the refrigerant, which increases the
temperature of the refrigerant.
BEFORE DRILLING OR DRIVING ANY
SCREWS INTO CABINET, CHECK TO BE
SURE THE SCREW WILL NOT HIT ANY
INTERNAL PARTS OR REFRIGERANT LINES.
Enertech Global
6
XT Models, Rev.: A
Section 3: Installation Considerations
Thermostat: Thermostats should be installed
approximately 54 inches off the floor on an
inside wall in the return air pattern and where
they are not in direct sunlight at anytime.
Consumer Instructions: Dealer should
instruct the consumer in proper operation,
maintenance, filter replacements, thermostat
and indicator lights. Also provide the consumer
with the manufacturer’s Owner's Manual for the
equipment being installed.
Loop Pumping Modules: Must be wired to the
heat pump’s electric control box. A special
entrance knockout is provided below the
thermostat entrance knockout. A pump
module connection block, connected to
the master contactor, and circuit breaker is
provided to connect the Pump Module wiring.
Enertech Global D-I-Y Policy: Enertech Global’s
geothermal heat pumps and system installations
may include electrical, refrigerant and/or water
connections. Federal, state and local codes
and regulations apply to various aspects of the
installation. Improperly installed equipment can
lead to equipment failure and health/safety
concerns. For these reasons, only qualified
technicians should install a Enertech Global built
geothermal system.
Desuperheater Package: Water heating is
standard on all residential units (units may be
ordered without). It uses excess heat, during
both heating and cooling cycles, to provide
hot water for domestic needs. A double wall
desuperheater exchanger (coil) located
between the compressor and the reversing
valve, extracts superheated vapor to heat
domestic water; while satisfying its heating and
cooling needs. The water circulation pump
comes pre-mounted in all residential units, but
must be electrically connected to the master
contactor. Leaving it unconnected ensures that
the pump is not run without a water supply.
The Desuperheater package can make up to
60% (depending on heat pump usage) of most
domestic water needs, but a water heater is still
recommended.
Because of the importance of proper installation,
Enertech Global does not sell equipment direct
to homeowners. Internet websites and HVAC
outlets may allow for purchases directly by
homeowners and do-it-yourselfers, but Enertech
Global offers no warranty on equipment that is
purchased via the internet or installed by persons
without proper training.
Enertech Global has set forth this policy
to ensure installations of Enertech Global
geothermal systems are done safely and
properly. The use of well-trained, qualified
technicians helps ensure that your system
provides many years of comfort and savings.
Desuperheater Piping: All copper tubes & fittings
should be 5/8” O.D (1/2” nom) minimum with a
maximum of 50ft separation. Piping should be
insulated with 3/8” wall closed cell insulation.
Equipment Installation: Special care should
be taken in locating the unit. All vertical units
should be placed on a vibration absorbing
pad (air pad) slightly larger than the base of
the unit. Downflow units should be placed on a
non-combustible base. Flex connectors should
also be installed in between the ductwork and
the unit. All units should be located in an indoor
area were the ambient temperature will remain
above 55°F and should be located in a way
that piping and ductwork or other permanently
installed fixtures do not have to be removed for
servicing and filter replacement.
Note: Copper is the only approved material for
desuperheater piping.
UV Light Usage: The use of a UV light in the unit
return air plenum should be such that the light
does not have a direct line of sight to the air
coil of the unit. UV lights could cause internal
wiring, foam insulation, or other components to
deteriorate. It would be better to place the UV
light in the supply air plenum, or ductwork. This
also helps keep the light cleaner. Additionally, if
a humidifier is installed and in line of the sight of
the UV light, consult the humidifier install manual
for indication of whether the light will deteriorate
any parts of the humidifier (like the pad).
Electrical: All wiring, line and low voltage,
should comply with the manufacturer's
recommendations, The National Electrical
Code, and all local codes and ordinances.
XT Models, Rev.: A
7
Enertech Global
Section 4: Unit Installation
UNIT PLACEMENT:
When installing a geothermal heating and
cooling unit, there are several items the installer
should consider before placing
the equipment.
1.
2.
3.
⚠ WARNING ⚠
DOWNFLOW UNITS REQUIRE THAT THE
FLOOR OPENING (BETWEEN THE UNIT AND
THE SUPPLY DUCT PLENUM) BE SLEEVED
THROUGH THE FLOOR WITH METAL DUCT.
THIS IS ESPECIALLY IMPORTANT IF THE UNIT
IS SITTING ON A PAD.
Service Access. Is there enough space for
service access? A general rule of thumb is
at least 2 feet in the front and 2 feet on at
least one side.
Unit Air Pad. All vertical geothermal
heating and cooling equipment should be
placed on either a formed plastic air pad,
or a high density, closed cell polystyrene
pad. Downflow units should be placed
on a non-combustible base. This helps
eliminate vibration noise that could be
transmitted through the floor.
The installer has verified that all applicable
wiring, ductwork, piping, and accessories
are correct and on the job site.
⚠ NOTICE ⚠
THE BLOWER SUPPORT BRACKET,
LOCATED ON THE BACK OF THE BLOWER
FOR SHIPPING PURPOSES, MUST BE
REMOVED BEFORE OPERATION. FAILURE
TO REMOVE THE BRACKET COULD RESULT
IN POTENTIALLY NOISY OPERATION AND
EQUIPMENT DAMAGE.
PRE-INSTALLATION:
Before you fully install the geothermal
equipment, it is recommended you go
through this quick checklist before placing the
equipment.
⧠
⧠
Fully inspect the unit after unpacking.
⧠
Remove and discard the blower motor
armature shaft shipping bracket from the
rear of the blower.
⧠
Locate the Unit Start-Up form from this
manual and have it available as the unit
installation proceeds.
⧠
Clean the air coil with soap and water
solution to remove any oil or dirt.
Open both the air handler section and
compressor section and removed any
packaging material or documentation
included in the unit.
Enertech Global
8
XT Models, Rev.: A
Section 4: Unit Installation
DIMENSIONAL DATA:
B
C
27.63
.97
Power Supply 1/2”
5.50
.89
1.13
CAP
High Voltage Supply 1”
E
BSP
Air Coil
D
D
A2
A1
Condensate
3/4” FPT
Condensate
3/4” FPT
Desuperheater Out
Desuperheater In
CSP
ASP
ASP
Source Out
Source In
Left View
Front & Back View
Control Panel
Plug Plate
30.33
28.01
Low Votage 1/2”
16.00
CAP
Plenum
Flanges
SA
P
Access
Panels
AIR COIL
SIDE
Filter
Rack
16.00
32.20
30.33
28.01
BS P
5.31
Control Box
32.20
Top View
14.00
Top Discharge
SA
CS P
P
LEGEND:
10.73
SAP = Service Access Panel
BSP = Blower Service Panel
CSP = Compressor Service Panel
CAP= Control Access Panel
ASP = Access Service Panel
FPT = Female Pipe Thread
Model
13.00
AIR COIL
SIDE
8.12
Dimensional Data
without Control Box
Dimensional Data
with Control Box
Bottom View
Bottom Discharge
Supply Air
(Top Discharge)
Supply Air
(Bottom Discharge)
Return Air
Height
(A1)
Width
(B)
Depth
(C)
Height
(A2)
Width
Depth
Width
Depth
Width
(E)
Height
(D)
024 048
56.1
30.3
32.2
62.5
16.0
16.0
13.0
14.0
26.0
28.0
060 072
60.1
30.3
32.2
66.5
16.0
16.0
13.0
14.0
26.0
32.0
Notes:
All Desuperheater connections are 3/4” FPT.
All measurements are in inches.
* For the source water loop, GeoComfort residential models use 1” double o-ring fittings. GeoComfort commercial models, Hydron
Module & TETCO models use 1” FPT fittings.
XT Models, Rev.: A
9
Enertech Global
Section 4: Unit Installation
Unit Physical Data
Dual Capacity Vertical
Model Number
024
036
048
060
072
Fan Wheel (in.)
10 x 11
10 x 11
10 x 11
10 x 11
10 x 11
.5
.5
.75
1
1
48
68
63
84
86
5.55
5.55
5.55
6.17
6.17
Fan Motor
ECM (HP)
Refrigerant Charge (oz.)
Air Coil
Face Area (Sq.Ft.)
Dimensions (in.)
31.8 x 25.1 x 1.0
Number Of Rows
N/A - Micro-Channel Coil
Filter 1” Thick
Unit Weight (nominal) - lbs
Enertech Global
35.9 x 24.7 x 1.26
28 x 30 x 1
395
400
28 x 34 x 1
450
10
455
460
XT Models, Rev.: A
Section 4: Unit Installation
Unit Conversion
UNIT CONVERSION:
Units are shipped in the left hand
return air, upflow configuration. The
control box is shipped inside the
unit. The control box plugs into the
electrical connection plate on the
top of the unit and mounts with two
screws to the top of the unit.
To convert the unit to right hand return air:
1. Remove the front panels and rear panels.
The panel screws are located under the
band that runs across the middle of the unit.
(GeoComfort & Hydron Module units only)
2. Rotate the unit to the correct position.
3. Move the unit controls connection plate
from its current position (on the top of the
unit) to the opposite side of the top of the
unit. Use the block off plate from that side to
cover the other side.
4. Mount the control box on what is now the
top front of the unit. Plugs are available now
to facilitate this.
5. Replace the front and rear panels onto
the unit.
The source, hot water generator, and
condensate fittings are on the air coil side
of the unit, under the air coil itself. These
connections are easier to facilitate if done prior
to the fitting of the return air drop.
To convert the unit to downflow supply air:
1. Remove the screws holding the blower and
heater housing and drop the
assembly down.
2. Remove the block off plate from the area
under the blower housing on the bottom
blower section panel.
3. Place the block off plate over the opening
where the blower housing was.
4. Install the downflow duct kit (instruction
included with kit, which is ordered and
shipped separately) in the compressor
section of the unit.
5. Install the heater and blower housing
assembly onto the downflow opening in the
blower section securing it with the screws
removed in step 1.
Figure 2: Blower Housing Connections
NOTE: Do not pry on the "belly band" that runs
across the front of the unit to hide the access
panel screws. Slight pressure on the rounded
portion of the "belly band" will release the catch.
(GeoComfort & Hydron Module units only)
XT Models, Rev.: A
11
Enertech Global
Section 4: Unit Installation
DUCT WORK:
All new ductwork shall be designed as
outlined in Sheet Metal and Air Conditioning
Contractors National Association (SMACNA)
or Air Conditioning Contractors of America
(ACCA) or American Society of Heating,
Refrigerating and Air Conditioning Engineers
(ASHRAE) handbooks.
All supply/return plenums should be isolated
from the unit by a flexible connector (canvas)
or equivalent to prevent transfer of vibration
noise to the ductwork. The flex connector
should be designed so as not to restrict airflow.
Turning vanes should be used on any transition
with airflow over 500 CFM. If the unit is installed
in a unconditioned space, the metal ductwork
should be insulated on the inside with fiberglass
insulation or similar insulation to prevent heat
loss/gain and to absorb air noise. If the unit
is being installed with existing ductwork, the
ductwork must be designed to handle the air
volume required by the unit being installed.
When running a cooling or heating load on
a building, size ductwork accordingly to the
building design load and heat pump CFM.
Industry Standard: When sizing ductwork use
400 CFM per Ton.
As a general rule, maximum recommended
face velocity for a supply outlet used in a
residential application is 750 FPM. Maximum
recommended return grille velocity is 600 FPM.
Systems with higher velocity, are likely to have
noise problems.
In buildings where ceilings are 8 feet or more,
at least 50 percent of the return air should be
taken back to the heat pump from the ceiling
or high sidewall location and not more than 50
percent from the floor or low sidewall location.
Table 1: Maximum Air Velocities
Location
Main Ducts
Branch Ducts
Grills, Registers, Diffusers
Enertech Global
Supply
900 FPM
700 FPM
750 FPM
Return
600 FPM
600 FPM
600 FPM
12
XT Models, Rev.: A
Section 4: Unit Installation
Figure 3: Standard Ductwork Connection Setup
Reducer
Supply Air Grille
Supply Air
Return Air Grille
Flex Connector
Flex Connector
Takeoff runs should
never be installed on a
reducer. Takeoffs
should be installed 6"
before a reducer and
at least 24" to 36"
past any reducer.
Return Air
Heat Pump
Accessible
Filter/Rack
Never install a takeoff on or near
a reducer or on an end cap, or near
an end cap. Exceptions may apply
NOTE: Maintain duct
size of supply flange
for at least 12”
before transitioning
to size of supply
plenum designed
for duct system.
The geothermal unit comes with
an ECM Motor. For maximum
performance, the blower speed
should be set to maintain between
350 and 450 CFM/ton. Use DIP
switch for ECM motor adjustments.
Figure 4: Ductwork with Split Damper Connection Setup
Thermostat
No. 2
Reducer
Never install a takeoff on or near a reducer or
on an end cap, or near a end cap.
Exceptions may apply.
Supply Air Grille
Thermostat
No. 1
Damper
Motor
Shift Damper
Return Air
Flex Connector
Accessible
Filter/Rack
XT Models, Rev.: A
13
Bypass
damper
not
shown
Split
Damper
Supply Air
Flex Connector
Takeoff runs should
never be installed on a
reducer. Takeoffs
should be installed 6"
before a reducer and
at least 24" to 36"
past any reducer.
Note: A bypass damper
is almost always required
for zoning systems.
Enertech Global
Section 5: Unit Piping Installation
Open Loop Piping
Placement of the components for an open
loop system are important when considering
water quality and long term maintenance. The
water solenoid valve should always be placed
on the outlet of the heat pump, which will keep
the heat exchanger under pressure when the
unit is not operating. If the heat exchanger is
under pressure, minerals will stay in suspension.
Water solenoid valves are also designed to
close against the pressure, not with the pressure.
Otherwise, they tend to be noisy when closing.
velocity noise. Always double check flow rate
at the P/T ports to make sure the ball valve
adjustments have not lowered water flow too
much, and essentially taken the flow regulator
out of the equation. It’s a good idea to remove
the ball valve handles once the system is
completed to avoid nuisance service calls.
A flow regulator should be placed after the
water solenoid valve. Always check the product
specification catalog for proper flow rate. A
calculation must be made to determine the
flow rate, so that the leaving water temperature
does not have the possibility of freezing.
Since the heat pump can operate at lower
waterflow on first stage, two stage units
typically include two water solenoid valves
to save water. The flow regulators should be
sized so that when one valve is open the unit
operates at first stage flow rate, and when
both valves are open, the unit operates at
full load flow rate. For example, a 4 ton unit
needs approximately 4 GPM on first stage, and
approximately 7 GPM at full load. The flow
regulator after the first valve should be 4 GPM,
and the flow regulator after the second valve
should be 3 GPM. When both valves are open,
the unit will operate at 7 GPM.
Other necessary components include a strainer,
boiler drains for heat exchanger flushing, P/T
ports and ball valves. Ball valves allow the
water to be shut off for service, and also help
when velocity noise is noticeable through the
flow regulator. Spreading some of the pressure
drop across the ball valves will lessen the
Hose kits are optional, but make for an easier
installation, since the P/T ports and connections
are included. The hose also helps to isolate the
heat pump from the piping system.
HEAT PUMP
Figure 5: Open Loop Piping Example
P/T Port
(2 required)
Ball Valve
(2 required)
Strainer
From Well
IN
Optional
Hose Kit*
S
OUT
Single
Speed
Units
Flow Regulator**
Discharge Line
Boiler Drain
for Heat
Exchanger
Maintenance
(2 required)
Enertech Global
S
Water
Solenoid
Valve
*Hose kit is used for piping
isolation, and includes
fittings for P/T ports.
**See product specification
catalog for flow rates.
S
14
TwoStage
Units
Note: All GXT, HXT, & TXT
units are two-stage units.
Not recommended for
3 ton and smaller. Use
single solenoid and
flow regulator.
XT Models, Rev.: A
Section 5: Unit Piping Installation
Water Quality
The quality of the water used in geothermal
systems is very important. In closed loop systems
the dilution water (water mixed with antifreeze)
must be of high quality to ensure adequate
corrosion protection. Water of poor quality
contains ions that make the fluid “hard” and
corrosive. Calcium and magnesium hardness
ions build up as scale on the walls of the system
and reduce heat transfer. These ions may also
react with the corrosion inhibitors in glycol based
heat transfer fluids, causing them to precipitate
out of solution and rendering the inhibitors
ineffective in protecting against corrosion. In
addition, high concentrations of corrosive ions,
such as chloride and sulfate, will eat through any
protective layer that the corrosion inhibitors form
on the walls of the system.
Ideally, de-ionized water should be used for
dilution with antifreeze solutions since deionizing removes both corrosive and hardness
ions. Distilled water and zeolite softened water
are also acceptable. Softened water, although
free of hardness ions, may actually have
increased concentrations of corrosive ions and,
therefore, its quality must be monitored. It is
recommended that dilution water contain less
than 100 PPM calcium carbonate or less than
25 PPM calcium plus magnesium ions; and less
than 25 PPM chloride or sulfate ions.
In an open loop system the water quality is
of no less importance. Due to the inherent
variation of the supply water, it should be tested
prior to making the decision to use an open
loop system. Scaling of the heat exchanger
and corrosion of the internal parts are two of
the potential problems. The Department of
Natural Resources or your local municipality
can direct you to the proper testing agency.
Please see Table 2 for guidelines.
Removing Debris During Purging
Most flow center or pump failures are a result of
poor water quality or debris. Debris entering the
loop during fusion and installation can cause
noise aand premature pump failure. Enertech
recommends a double flush filtering method
during purging. When purging, use a 100
micron bag filter until air bubbles are removed.
Remove the 100 micron bag, replace it with a 1
micron bag and restart the flushing.
Table 2: Water Quality
Potential
Problem
Chemical(s) or Condition
Range for Copper
Heat Exchangers
Range for Cupro-Nickel Heat
Exchangers
Scaling
Calcium & Magnesium Carbonate
Less than 350 ppm
Less than 350 ppm
pH Range
7-9
5-9
Total Disolved Solids
Less than 1000 ppm
Less than 1500 ppm
Corrosion
Ammonia, Ammonium Hydroxide
Less than 0.5 ppm
Less than 0.5 ppm
Ammonium Chloride, Ammonium Nitrate
Less than 0.5 ppm
Less than 0.5 ppm
Calcium Chloride / Sodium Chloride
Less than 125 ppm
Less than 125 ppm - Note 4
Biological
Growth
Erosion
Chlorine
Less than 0.5 ppm
Less than 0.5 ppm
Hydrogen Sulfide
None Allowed
None Allowed
Iron Bacteria
None Allowed
None Allowed
Iron Oxide
Less than 1 ppm
Less than 1 ppm
Suspended Solids
Less than 10 ppm
Less than 10 ppm
Water Velocity
Less than 8 ft/s
Less than 12 ft/s
Notes:
1. Harness in ppm is equivalent to hardness in mg/l.
2. Grains/gallon = ppm divided by 17.1.
3. Copper and cupro-nickel heat exchangers are not recommended for pool applications for water outside the range of the table.
Secondary heat exchangers are required for applications not meeting the requirements shown above.
4. Saltwater applications (approx. 25,000 ppm) require secondary heat exchangers due to copper piping between the heat exchanger
and the unit fittings.
XT Models, Rev.: A
15
Enertech Global
Section 5: Unit Piping Installation
Interior Piping
All interior piping must be sized for proper flow
rates and pressure loss. Insulation should be
used on all inside piping when minimum loop
temperatures are expected to be less than
50°F. Use the table below for insulation sizes with
different pipe sizes. All pipe insulation should
be a closed cell and have a minimum wall
thickness of 3/8”. All piping insulation should
be glued and sealed to prevent condensation
and dripping. Interior piping may consist of the
following materials: HDPE, copper, brass, or
rubber hose (hose kit only). PVC is not allowed
on pressurized systems.
Table 3: Pipe Insulation
Piping Material
Insulation Description
1” IPS PE
1-1/4” ID - 3/8” Wall
1” IPS Hose
1-1/4” IPS PE
2” IPS PD
1-3/8” ID - 3/8” Wall
Typical Pressurized Flow Center Installation
The flow centers are insulated and contain
all flushing and circulation connections for
residential and light commercial earth loops
that require a flow rate of no more than 20
gpm. 1-1/4” fusion x 1” double o-ring fittings
(AGA6PES) are furnished with the double
o-ring flow centers for HDPE loop constructions.
Various fittings are available for the double
o-ring flow centers for different connections.
See figure 6 for connection options. A typical
installation will require the use of a hose kit.
Matching hose kits come with double o-ring
adapters to transition to 1” hose connection.
Note: Threaded flow centers all have 1” FPT
connections. Matching hose kits come with the
AGBA55 adapter needed to transition from 1”
FPT to 1” hose.
1-5/8” ID - 3/8” Wall
2-1/8” ID - 3/8” Wall
Figure 6: Typical Single Unit Piping Connection (Pressurized Flow Center)
To/From
Loop Field
~~
Air Coil
Flow
Center
Hose
Kit
Note: P/T ports should be angled
P/T Portsaway from the unit for
ease of
Source
Water Out
gauge reading.
Enertech Global
16
Equipment Pad
Source Water In
XT Models, Rev.: A
Section 5: Unit Piping Installation
Typical Non-Pressurized Flow Center Installation
Standing column flow centers are designed to
operate with no static pressure on the earth
loop. The design is such that the column of
water in the flow center is enough pressure to
prime the pumps for proper system operation
and pump reliability. The flow center does have
a cap/seal, so it is still a closed system, where the
fluid will not evaporate. If the earth loop header
is external, the loop system will still need to be
flushed with a purge cart. The non-pressurized
flow center needs to be isolated from the flush
cart during flushing because the flow center
is not designed to handle pressure. Since this
is a non-pressurized system, the interior piping
can incorporate all the above-mentioned pipe
material options (see interior piping), including
PVC. The flow center can be mounted to the
wall with the included bracket or mounted on
the floor as long as it is properly supported.
Figure 7: Typical Single Unit Piping Connection (Non-Pressurized Flow Center)
XT Models, Rev.: A
17
Enertech Global
Section 5: Unit Piping Installation
Condensation Drain Connection
Connect the EZ-Trap to the equipment
condensate drain drain connection as shown
in figures 9a through 9d. The condensate line
must be trapped a minimum of 1.0” as shown
on diagram. The condensate line should be
pitched away from the unit a minimum of
1/4” per foot. The condensate line from the
unit drain connection to the P-trap should be
sloped downward. For moreinformation on
installing EZ-Trap, see installationsheet that
comes with the EZ-Trap Kit. Always install the air
vent after the trap.
Note: Make Sure the condensate overflow
sensor is mounted to the side closest to the
drain being used as shown in figures 9c and 9d
below.
Figure 9c: Left Overflow Sensor Connection
Figure 9a: Condensation Drain Connection
Figure 9d: Right Overflow Sensor Connection
Figure 9b: Condensation Drain Drop
Note: Connect the drain through the trap to
the condensation drain system in conformance
to local plumbing codes.
Part Number Description
ACDT1A
EZ-Trap ¾” Kit
ACDT2A
EZ-Trap 1” Kit
Enertech Global
18
XT Models, Rev.: A
Section 6: Antifreeze
Convenience: Is the antifreeze available and
easy to transport and install?
Antifreeze Overview
In areas where minimum entering loop
temperatures drop below 40°F, or where piping
will be routed through areas subject to freezing,
antifreeze is required. Alcohols and glycols
are commonly used as antifreeze. However,
local and state/provincial codes supersede
any instructions in this document. The system
needs antifreeze to protect the coaxial heat
exchanger from freezing and rupturing.
Freeze protection should be maintained to
15°F below the lowest expected entering
source loop temperature. For example, if 30°F
is the minimum expected entering source
loop temperature, the leaving source loop
temperature could be 22 to 25°F. Freeze
protection should be set at 15°F (30-15 =
15°F). To determine antifreeze requirements,
calculate how much volume the system holds.
Then, calculate how much antifreeze will
be needed by determining the percentage
of antifreeze required for proper freeze
protection. See Tables 4 and 5 for volumes and
percentages. The freeze protection should be
checked during installation using the proper
hydrometer to measure the specific gravity and
freeze protection level of the solution.
Codes: Will the brine meet local and state/
provincial codes?
The following are some general observations
about the types of brines presently being used:
Methanol: Wood grain alcohol that is
considered toxic in pure form. It has good heat
transfer, low viscosity, is non-corrosive, and is mid
to low price. The biggest down side is that it is
flammable in concentrations greater than 25%.
Ethanol: Grain alcohol, which by the ATF
(Alcohol, Tobacco, Firearms) department
of the U.S. government, is required to be
denatured and rendered unfit to drink. It has
good heat transfer, mid to high price, is noncorrosive, non-toxic even in its pure form, and
has medium viscosity. It also is flammable with
concentrations greater than 25%. Note that
the brand of ethanol is very important. Make
sure it has been formulated for the geothermal
industry. Some of the denaturants are not
compatible with HDPE pipe (for example,
solutions denatured with gasoline).
Antifreeze Characteristics
Selection of the antifreeze solution for closed
loop systems require the consideration of
many important factors, which have long-term
implications on the performance and life of
the equipment. Each area of concern leads to
a different “best choice” of antifreeze. There
is no “perfect” antifreeze. Some of the factors
to consider are as follows (Brine = antifreeze
solution including water):
Safety: The toxicity and flammability of the brine
(especially in a pure form).
Cost: Prices vary widely.
Thermal Performance: The heat transfer and
viscosity effect of the brine.
Corrosiveness: The brine must be compatible
with the system materials.
Stability: Will the brine require periodic change
out or maintenance?
XT Models, Rev.: A
Propylene Glycol: Non-toxic, non-corrosive,
mid to high price, poor heat transfer, high
viscosity when cold, and can introduce micro
air bubbles when adding to the system. It
has also been known to form a “slime-type”
coating inside the pipe. Food grade glycol is
recommended because some of the other
types have certain inhibitors that react poorly
with geothermal systems. A 25% brine solution is
a minimum required by glycol manufacturers,
so that bacteria does not start to form.
Ethylene Glycol: Considered toxic and is not
recommended for use in earth loop applications.
GS4 (POTASSIUM ACETATE): Considered highly
corrosive (especially if air is present in the
system) and has a very low surface tension,
which causes leaks through most mechanical
fittings. This brine is not recommended for use in
earth loop applications.
19
Enertech Global
Section 6: Antifreeze
Table 4: Pipe Fluid Volume
Notes:
1. Consult with your representative or
distributor if you have any questions
regarding antifreeze selection or use.
2. All antifreeze suppliers and manufacturers
recommend the use of either de-ionized or
distilled water with their products.
Type
Copper
1” CTS
4.1
Copper
1.25” CTS
HDPE
.75 SDR11
HDPE
1.25” SDR11
7.5
HDPE
2” SDR11
15.4
Copper
Antifreeze Charging
Calculate the total amount of pipe in the
system and use Table 4 to calculate the
amount of volume for each specific section of
the system. Add the entire volume together,
and multiply that volume by the proper
antifreeze percentage needed (Table 5) for the
freeze protection required in your area. Then,
double check calculations during installation
with the proper hydrometer and specific gravity
chart (Figure 9) to determine if the correct
amount of antifreeze was added.
Volume Per 100ft
US Gallons
Size
HDPE
HDPE
1.5” CTS
1” SDR11
1.5: SDR11
6.4
9.2
3.0
4.7
9.8
Additional component volumes:
Unit coaxial heat exchanger = 1 Gallon
Flush Cart = 8-10 Gallons
10’ of 1” Rubber Hose = 0.4 Gallons
⚠ CAUTION ⚠
USE EXTREME CARE WHEN OPENING,
POURING, AND MIXING FLAMMABLE
ANTIFREEZE SOLUTIONS. REMOTE FLAMES
OR ELECTRICAL SPARKS CAN IGNITE
UNDILUTED ANTIFREEZES AND VAPORS.
USE ONLY IN A WELL VENTILATED AREA.
DO NOT SMOKE WHEN HANDLING
FLAMMABLE SOLUTIONS. FAILURE TO
OBSERVE SAFETY PRECAUTIONS MAY
RESULT IN FIRE, INJURY, OR DEATH. NEVER
WORK WITH 100% ALCOHOL SOLUTIONS.
Enertech Global
20
XT Models, Rev.: A
Section 6: Antifreeze
Table 5: Antifreeze Percentages by Volume
Type of Antifreeze
10°F (-12.2°C)
ProCool (Ethanol)
25%
Methanol
Minimum Temperature for Freeze Protection
15°F (-9.4°C)
20°F (-6.7°C)
25°F (-3.9°C)
21%
16%
10%
22%
25%
Propylene Glycol
38%
Heat Transfer Fluid (HTF)
17%
30%
12%
22%
15%
Mix according to manufacturer’s directions on container label
Antifreeze solutions are shown in pure form - not premixed
HTF is a premixed Methanol solution
NOTE: Most manufacturers of antifreeze
solutions recommend the use of de-ionized
water. Tap water may include chemicals that
could react with the antifreeze solution.
Figure 9: Antifreeze Specific Gravity
1.0500
1.0400
1.0300
Specific Gravity
1.0200
1.0100
1.0000
0.9900
0.9800
0.9700
0.9600
-5
0
5
10
15
20
25
30
32
Freeze Protection (deg F)
Procool
XT Models, Rev.: A
Methanol
21
Propylene Glycol
Enertech Global
Section 7: Desuperheater Installation
PLUMBING INSTALLATION
Desuperheater Installation
Units that ship with the desuperheater function
also ship with a connection kit.
NOTE: All plumbing and piping connections
must comply with local plumbing codes.
Note: Desuperheater capacity is based on 0.4
GPM Flow per nominal ton at 90°F entering hot
water temperature.
Note: Units that are shipped with a
desuperheater do not have the desuperheater
pump wires connected to the electrical circuit,
to prevent accidentally running the pump while
dry. Pump has to be connected to the electric
circuit (master contactor) when the lines from
the water heater are installed & air is removed.
CONTENTS OF THE DESUPERHEATER FITTING
KIT:
•
(1) p/n 20D052-01NN, Installation Instruc-
tions
•
(1) p/n 33P211-01BN, 3/4”x 3/4”x 3/4” FPT
Brass Tee
•
(1) p/n 33P210-01NN, ¾” Boiler
Drain Valve
•
(1) p/n 11080005001, ¾” MPT x 3-1/2”
Brass Nipple
•
(3) p/n 11080006001, ½” SWT x ¾” MPT
Copper Adaptor
•
(1) p/n 11080007001, ¾” x ¾” x ½” SWT
Copper Tee
⚠ WARNING ⚠
TO AVOID SERIOUS INJURY, IT IS
RECOMMENDED THAT AN ANTI-SCALD
MIXING VALVE IS INSTALLED ON THE HOT
WATER SUPPLY LINE INTO THE HOME. EVEN
THOUGH HOT WATER TANK TEMPERATURES
COULD APPEAR TO BE SET AT LOWER
LEVELS, HIGH TEMPERATURE WATER UP
TO 130 DEGREES
FROM
THE DESUPERHEATER COULD RAISE TANK
TEMPERATURES TO UNSAFE LEVELS.
TIP: Measure the distance above the floor or
shelf that the water heater is setting on, to
where the drain valve is located. This distance
must be greater than one-half the width of the
tee you’re about to install, or you won’t be able
to thread the tee on to the water heater.
1. Disconnect electricity to water heater.
2. Turn off water supply to water heater.
3. Drain water heater. Open pressure
relief valve.
4. Remove drain valve and fitting from water
heater.
5. Thread the ¾” MPT x 3-1/2” nipple into the
water heater drain port. Use Teflon tape, or
pipe dope on threads.
6. Thread the center port of the ¾” brass tee
to the other end of the nipple.
7. Thread one of the copper adaptors
into the end of the tee closest to the heat
pump.
8. Thread the drain valve into the other end of
the nipple. See Figure 1.
9. Above the water heater, cut the incoming
cold water line. Remove a section of that
line to enable the placement of the copper
tee.
10. Insert the copper tee in the cold water line.
See Figure 2.
11. Thread the remaining two ½”SWT x ¾”MPT
copper adaptors into the ¾” FPT fittings on
the heat pump, marked HWG IN and HWG
OUT.
12. Run interconnecting ½” copper pipe from
the HOT WATER OUT on the heat pump, to
the copper adaptor located on the tee at
the bottom of the water heater.
13. Run interconnecting ½” copper pipe from
the HOT WATER IN on the heat pump, to the
copper tee in the cold water line.
Enertech Global
22
XT Models, Rev.: A
Section 7: Desuperheater Installation
14. Install an air vent fitting at the highest point
of the line from step 13 (assuming it’s the
higher of the two lines from the heat pump
to the water heater).
17. Flush the interconnecting lines, and check
for leaks. Make sure air vent is shoutoff
when water begins to drip steadily from the
vent.
15. Shut off the valve installed in the
desuperheater line close to the tee in the
cold water line. Open the air vent and all
shut off valves installed in the “hot water
hot”.
18. Loosen the screw on the end of the
despuerheater pump to purge the air from
the pump’s rotor housing. A steady drip
of water will indicate the air is removed.
Tighten the screw and the pump can be
connected to the contactor or teminal
block.
16. Turn the water supply to the water heater
on. Fill water heater. Open highest hot
water faucet to purge air from tank and
piping.
19. Install 3/8” closed cell insulation on the lines
connecting the heat pump to the water
heater.
20. Reconnect electricity to water heater.
Figure 10: Water Heater Connection Kit
Assembly for Bottom of Water Heater
NOTE:
Drawing shown vertically for detail. Fitting installs horizontally into hot water tank.
Desuperheater circuits are NOT to be connected to gas water heaters!
Connection to Hot
Water Tank
Copper Tee
For Domestic
Cold Water In
Line (installed
within 12” from
top of tank)
Drain
Brass Tee
Adapter to Unit
Water Line
XT Models, Rev.: A
23
Enertech Global
Section 7: Desuperheater Installation
Figure 11: Typical Desuperheater Installation
Cold Water
Hot Water Supply
Shutoff
Valves
Air Vent
Located at
System
High Point
Unit Water
Connection Detail
Air Coil
Hot Water Out
Water Heater
(or Storage Tank)
Hot Water In
3/4” Copper
Adapter Fitting
Drain
Valve
Shutoff
Valves
HWG Out
HWG In
Figure 12: Desuperheater Installation with Preheat Tank
Hot Water
Cold Water
Supply
Cold Water
Supply
Shutoff
Valves
Hot Water
Air Vent
Located at
System
High Point
Unit Water
Connection Detail
Air Coil
Hot Water Out
Water Heater No. 2
(or Storage Tank)
Water Heater No. 1
(or Storage Tank)
Hot Water In
3/4” Copper
Adapter Fitting
Drain
Valve
Drain
Valve
Shutoff
Valves
HWG Out
HWG In
Desuperheater circuits are NOT to be connected to gas water heaters!
Enertech Global
24
XT Models, Rev.: A
Section 8: Controls
MICROPROCESSOR FEATURES AND OPERATION
Enertech Global geothermal heat pump
controls provide a unique modular approach
for controlling heat pump operation. The
control system uses one, two, or three printed
circuit boards, depending upon the features
of a particular unit. This approach simplifies
installation and troubleshooting, and eliminates
features that are not applicable for some units.
Water Solenoid Valve Connections
Two accessory relay outputs at the terminal
strip provide a field connection for two types
of water solenoid valves, a standard 24VAC
solenoid valve, or a 24VAC solenoid valve
with an end switch. Additional field wiring is no
longer required for operation of the end switch.
A microprocessor-based printed circuit board
controls the inputs to the unit as well as outputs
for status mode, faults, and diagnostics. A
status LED and an LED for each fault is provided
for diagnostics. An ECM control module
provides field selectable options for airflow and
dehumidification mode, plus an LED to indicate
CFM (100 CFM per flash).
Removable low voltage terminal strips provide all
necessary terminals for field connections. Not only
are the thermostat inputs included, but there are
also two additional removable terminal strips for
all of the accessory and electric heat wiring for
ease of installation and troubleshooting.
Startup/Random Start
The unit will not operate until all the inputs
and safety controls are checked for normal
conditions. At first power-up, the compressor is
energized after a five minute delay. In addition,
a zero to sixty second random start delay is
added at first power-up to avoid multiple units
from being energized at the same time.
Short Cycle Protection
A built-in five minute anti-short cycle
timer provides short cycle protection of
the compressor.
Component Sequencing Delays
Components are sequenced and delayed for
optimum space conditioning performance and
to make any startup noise less noticeable.
Test Mode
The microprocessor control allows the
technician to shorten most timing delays for
faster diagnostics by changing the position of a
jumper located on the lockout board.
XT Models, Rev.: A
Humidifier/Dehumidification Connections
Connections for a humidistat are provided,
which automatically engages the fan when
the humidistat contact closes. In addition, a
field connection is provided at the terminal
strip for external control of the On Demand
Dehumidification (ODD) feature for the variable
speed ECM motor, which automatically lowers
the fan speed when the space humidity is
higher than set point. Either connection may be
used with a thermostat that includes humidifier/
dehumidification outputs. Not applicable for
splits/water-to-water.
Airflow Monitor
An LED on the ECM control module flashes
one time per 100 CFM when the unit’s fan is
operating to indicate airflow.
Resistance Heat Control
The electric heat control module contains the
appropriate high-voltage control relays. Low
voltage control signals from the compressor
section energize the relays in the electric heat
module to engage backup electric heat
when necessary.
Electronic Condensate Overflow Protection
The control board utilizes an impedance
sensing liquid sensor at the top of the drain pan.
Since the drain pan is grounded, when water
touches the sensor for 30 continuous seconds,
the sensor sends a ground signal to the lockout
board, indicating that a condensate overflow
fault has occurred.
Loop Pump Circuit Breakers
The loop pump(s) and desuperheater pump
are protected by control box mounted circuit
breakers for easy wiring of pumps during
installation. Circuit breakers eliminate the need
to replace fuses.
25
Enertech Global
Section 8: Controls
CFM
Figure 13: ECM Board Layout
COM
W1
COM2
24VAC XFMR
SEC
ECM
Board
O/B Y1 G W1 R ODD W2 Y2 C
Safety Controls
The control receives separate signals for
high pressure, low pressure, low water flow,
and condensate overflow faults. Upon a
continuous 30-second measurement of the
fault (immediate for high pressure), compressor
operation is suspended (see Fault Retry below),
and the appropriate LED flashes. Once the unit
is locked out (see Fault Retry below), an output
(terminal “L”) is made available to a fault LED
at the thermostat.
Low Pressure: If the low pressure switch is open
for 30 continuous seconds, the compressor
operation will be interrupted, and the control
will go into fault retry mode. At startup, the low
pressure switch is not monitored for 90 seconds
to avoid nuisance faults.
High Pressure: If the high pressure switch
opens, the compressor operation will be
interrupted, and the control will go into fault
retry mode. There is no delay from the time the
switch opens and the board goes into fault
retry mode. There is also no delay of switch
monitoring at startup.
Flow Switch: If the flow switch is open for 30
continuous seconds, the compressor operation
will be interrupted, and the control will go into
fault retry mode. At startup, the flow switch
is not monitored for 30 seconds to avoid
nuisance faults.
Condensate Overflow: If water touches the
condensate overflow sensor for 30 continuous
seconds, the compressor operation will be
interrupted, and the control will go into
fault retry mode. There is no delay of switch
monitoring at startup.
Enertech Global
FAULT RETRY
All faults are retried twice before finally locking
the unit out. The fault retry feature is designed to
prevent nuisance service calls. There is an antishort cycle period between fault retries. On the
third fault, the board will go into lockout mode.
Over/Under Voltage Shutdown
The lockout board protects the compressor
from operating when an over/under voltage
condition exists. The control monitors secondary
voltage (24VAC) to determine if an over/
under voltage condition is occurring on the
primary side of the transformer. For example, if
the secondary voltage is 19 VAC, the primary
voltage for a 240V unit would be approximately
190V, which is below the minimum voltage
(197V) recommended by the compressor
manufacturer. This feature is self-resetting. If
the voltage comes back within range, normal
operation is restored. Therefore, over/under
voltage is not a lockout.
Under voltage (18 VAC) causes the compressor
to disengage and restart when the voltage
returns to 20 VAC. Over voltage (31 VAC)
causes the compressor to disengage and
restart when the voltage returns to 29 VAC.
During an over or under voltage condition,
all five fault LEDs will blink (HP + LP + FS + CO
+ Status). When voltage returns to normal
operation, the four fault LED’s will stop blinking,
but the status LED will continue to flash. While
the board LEDs are flashing, the thermostat
fault light will be illuminated.
Intelligent Reset
If the thermostat is powered off and back
on (soft reset), the board will reset, but the
last fault will be stored in memory for ease of
troubleshooting. If power is interrupted to the
board, the fault memory will be cleared.
Lockout with Emergency Heat
While in lockout mode, if the thermostat is
calling for backup heat, emergency heat
mode will occur.
26
XT Models, Rev.: A
Section 8: Controls
Diagnostics
The lockout board includes five LEDs (status,
high pressure, low pressure, low water flow,
condensate overflow) for fast and simple
control board diagnosis. Below is a table
showing LED function.
Table 6: LED Identification
LED Color
Location1
Function
Normal Operation
Fault Retry2
Lockout2
Green
Top
High Pressure
OFF
Flashing
3
ON3
Orange
2nd
Low Pressure
OFF
Flashing3
ON3
Red
3rd
Water Flow
OFF
Flashing3
ON3
Yellow
4th
Condensate
Overflow
OFF
Flashing3
ON3
Green
Bottom
Status
Flashing4
Flashing5
Flashing4
Notes:
1. Looking at the board when the LEDs are on the right hand side.
2. If all five lights are flashing, the fault is over/under voltage.
3. Only the light associated with the particular fault/lockout will be on or flashing.
For example, if a high pressure lockout has occurred, the top green light will be on.
The orange, red, and yellow lights will be off.
4. Status lights will be off when in test mode.
5. Flashes alternately with the fault LED.
Hot Water Pump Control
Controls for high water temperature and low
compressor discharge line temperature prevent
the hot water (desuperheater) pump from
operating when the leaving water temperature
is above 130°F, or when the compressor
discharge line is too cool to provide adequate
water heating.
Lockout Board Jumper Selection
The lockout board includes three jumpers for
field selection of various board features.
Water Solenoid Valve Delay (WSD): When the
WSD jumper is installed, the “A” terminal is
energized 10 seconds before the compressor
is energized. When the jumper is removed, the
“A” terminal is energized with the compressor.
If using a water solenoid valve without an end
switch, connect to terminal “A”. If using a water
solenoid valve with an end switch, connect to
terminals YT and YU(remove the jumper wire).
Refer to wiring diagram. Enertech recommends
the use of a slow acting valve to reduce the
chance of water hammer.
XT Models, Rev.: A
Test Mode (TEST): When the TEST jumper is
installed, the board operates in the normal
mode. When the jumper is removed, the board
operates in test mode, which speeds up all
delays for easier troubleshooting. When service
is complete, the jumper must be re-installed
in order to make sure that the unit operates
with normal sequencing delays. While the test
jumper is removed, the status light (bottom
green) will remain off.
Over/Under Voltage Disable (O/V): When the
O/V jumper is installed, the over/under voltage
feature is active. When the jumper is removed,
the over/under voltage feature is disabled.
On rare occasions, variations in voltage will be
outside the range of the over/under voltage
feature, which may require removal of the
jumper. However, removal of the jumper could
cause the unit to run under adverse conditions,
and therefore should not be removed without
contacting technical services. An over/under
voltage condition could cause premature
component failure or damage to the unit
controls. Any condition that would cause
this fault must be thoroughly investigated
before taking any action regarding the jumper
27
Enertech Global
Section 8: Controls
Figure 14: Lockout Board Layout
removal. Likely causes of an over/under
voltage condition include power company
transformer selection, insufficient entrance
wire sizing, defective breaker panel, incorrect
transformer tap (unit control box), or other
power-related issues.
CCG
R2 R1 C2 C1
CC
Lockout
Board
SEQUENCE OF OPERATION:
Water-to-Air Units, Single Compressor, ECM Fan
A
C
R
Y
L
O
Heating, 1st Stage (Y1,G) Two-Stage Units
The ECM fan is started immediately at 75% (of
1st stage operation) CFM level (based on DIP
switch settings), first stage compressor and the
loop/desuperheater pump(s) are energized 10
seconds after the “Y1” input is received, and the
ECM fan adjusts to 100% (of 1st stage operation)
CFM level 30 seconds after the “Y1” input.
Heating, 2nd Stage (Y1,Y2,G) Two-Stage Units
The ECM fan adjusts to 2nd stage CFM level
(based on DIP switch settings), and the
compressor full load solenoid valve is energized.
Heat, 3rd Stage (Y1,Y2,W,G) Two-Stage Units
The ECM fan remains at 100% of 2nd stage CFM
level (based on DIP switch settings), and the
electric backup heat is energized.
Emergency Heat (W,G)
The fan is started immediately at 2nd stage
CFM level (based on DIP switch settings), and
the electric backup heat is energized.
Cooling Operation
The reversing valve is energized for cooling
operation. Terminal “O” from the thermostat is
connected to the reversing valve solenoid.
WSD
TEST
O/V
HP
HP
LP
LP
FS
FS
CO
CO
Status
Cooling, Dehumidification Mode
The ECM control module includes two
types of dehumidification modes, Forced
Dehumidification mode, and On Demand
Dehumidification (ODD). If the ECM control
module is set to Forced Dehumidification
mode, the ECM fan runs at normal CFM in all
heating stages, but all cooling operation will
be 85% of the current stage CFM level (based
on DIP switch settings), which lowers the CFM
through the evaporator coil, improving latent
capacity. In ODD mode, a humidistat or a
thermostat with a dehumidification output
(output must be reverse logic -- i.e. it must
operate like a humidistat) is connected to the
ODD terminal. When the module receives a
call for dehumidification, the fan runs at 85%
of the current stage CFM in the cooling mode.
Otherwise, the airflow is at the normal CFM
level. The signal is ignored in the heating mode.
Fan Only
When the ECM control module receives a “G”
call without a call for heating or cooling, the
fan operates at a lower CFM level (based on
DIP switch settings).
Cooling, 1st stage (Y1,0,G) Two-Stage Units
The ECM fan is started immediately at 75% (of
1st stage operation) CFM level (based on DIP
switch settings), first stage compressor and the
loop/desuperheater pump(s) are energized 10
seconds after the “Y1” input is received, and the
ECM fan adjusts to 100% (of 1st stage operation)
CFM level 30 seconds after the “Y1” input.
Cooling, 2nd Stage (Y1,Y2,O,G) Two-Stage Units
The ECM fan adjusts to 2nd stage CFM level
(based on DIP switch settings), and the
compressor full load solenoid valve is energized.
Enertech Global
28
XT Models, Rev.: A
Section 8: Controls
Table 7: ECM Fan Performance - Two-Stage Compressor Units
ECM Fan Performance - Two-Stage Compressor Units
Model1
Program2
A
024
036
048
060
072
Heating Modes
Cooling Modes
Dehumidification
Mode6
1st
Stage
2nd
Stage
1st
Stage
2nd
Stage
1st
Stage
2nd
Stage
800
1000
800
1000
680
850
Only
Fan
550
DIP Switch Settings4
S1
S2
S3
S4
S5
S6
S7
S8
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
B
750
950
750
950
640
810
515
ON
OFF
OFF
OFF
ON
OFF
OFF
C
700
850
700
850
595
725
475
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
D
600
750
600
750
510
640
450
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
A
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
B
1050
1350
1050
1350
895
1150
700
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
C
950
1200
950
1250
810
1065
635
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
D
850
1100
850
1150
725
980
575
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
A
1500
1800
1500
1900
1275
1615
945
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
B
1450
1700
1450
1750
1235
1490
890
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
C
1300
1500
1300
1600
1105
1360
680
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
D
1150
1350
1150
1400
725
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
A
1850
2200
1750
2100
1490
1785
980
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
B
1600
1850
1650
1950
1405
1660
870
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
1235
1490
C
1450
1700
1450
1750
D
1300
1500
1300
1550
A
-
-
-
-
1490
800
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
725
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
-
-
-
-
-
-
-
-
-
-
1830
B
1850
2100
1750
2150
1075
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
C
1650
2000
1600
1900
975
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
D
1500
1750
1450
1700
875
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
Notes:
1. Program B (Bold type) is factory settings and rated CFM. CFM is controlled within 5% up to the max. ESP.
Max. ESP includes allowance for wet coil and standard filter.
2. Power must be off to the unit for at least 3 seconds before the ECM motor will recognize a speed change.
3. Max ESP for models with internal electric heat is 0.6” ESP.
Dehumidification Mode Options
DIP Switch
S9
S10
ON
OFF
Mode
Operation
Normal
Dehumidification mode disabled (normal Htg/Clg CFM) - factory setting
OFF
ON
ODD
On Demand dehumidification mode (humidistat input at terminal ODD) Humidistat required
OFF
OFF
Constant Dehum
Constant dehumidification mode (always uses dehum CFM for cooling and
normal CFM for heating) - No humidistat required
ON
ON
Not Used
Not an applicable selection
Notes:
1.To enter dehumidification mode, ODD input should be 0 VAC; for normal cooling CFM, ODD input should be 24VAC.
2. Heating CFM is not affected by dehumidification mode. When in dehumidification mode, cooling CFM is 85% of normal
cooling CFM.
XT Models, Rev.: A
29
Enertech Global
Section 8: Controls
Enertech Global
30
XT Models, Rev.: A
Section 8: Controls
XT Models, Rev.: A
31
Enertech Global
Section 8: Controls
Enertech Global
32
XT Models, Rev.: A
Section 9: Accessories
Table 9: Auxiliary Heater Electrical Data
Heater Model
Supply
Circuit
Number
AHTR101C
Single
AHTR151C
AHTR201C
L1/L2
L3/L4
L1/L2
L3/L4
Technical Data (AHTR Electric Heaters Only) Single Phase w/ Circuit Breaker
Recommended
MOCP
Branch Circuit Conductor
Maximum
MCAFLA
75°C Copper
Overcurrent
Heater kW
Minimum
NEC 310.15(B)(16), Ch. 9 Table 9
Heat kW
Total
Protective
Per Circuit
Circuit
AMPS
Device
Min Wire
Ampacity
Max
(AMPS)
Size
# of
Length (ft)
NEC 240.4(B)
Wires (AWG)
Ground
Wire
NEC 250.122
Min Wire
Size
(AWG)
240
208
240
208
240
208
240
208
240
208
240
208
240
208
10
7.5
5
3.75
41.7
36.1
52.1
45.1
60
50
2
6
8
0
0
240 208
10
15
11.25
5
3.75
20.8
18.0
26.0
22.5
30
25
2
10
12
0
0
10
20
15
10
10
10
7.50
7.50
7.50
41.7
41.7
41.7
36.1
36.1
36.1
52.1
52.1
52.1
45.1
45.1
45.1
60
60
60
50
50
50
2
2
2
6
6
6
8
8
8
0
0
0
0
0
0
10
10
10
Technical Data (AHTR Electric Heaters Only) Single Phase w/ Circuit Breaker and Single Point Connection Block
Recommended
MOCP
Branch Circuit Conductor
Ground
Maximum
MCA75°C Copper
Wire
FLA
Overcurrent
Heater kW
Minimum
Supply
NEC 310.15(B)(16), Ch. 9 Table 9
NEC 250.122
Heat kW
Total
Protective
Per Circuit
Circuit
Heater Model Circuit
AMPS
Device
Min Wire
Min Wire
Ampacity
Number
Max
(AMPS)
Size
Size
# of
Length (ft)
NEC 240.4(B)
(AWG)
Wires (AWG)
240
208
AHTR151CC*
Single
15
11.25
AHTR201CC*
Single
20
15
240
5
10
10
10
208
3.75
7.50
7.50
7.50
240
208
240
208
240
208
62.5
54.1
78.1
67.6
80
70
83.3
72.1 104.2 90.1
110
100
240
208
240
208
2
4
4
0
0
2
2
3
0
0
240
208
8
6
8
*Single Point Connection
XT Models, Rev.: A
33
Enertech Global
Section 9: Accessories
Figure 15: Auxiliary Heater Placement
APSMA PUMP SHARING MODULE
The pump sharing module, part number APSMA, is designed to allow two units to share one
flow center. With the APSMA module, either
unit can energize the pump(s). Connect the
units and flow center as shown in Figure 16,
below. Figure 17 includes a schematic of the
board. The module must be mounted in a
NEMA enclosure or inside the unit control box.
Local code supersedes any recommendations
in this document.
Heater Support Rod Fits into Hole
Rotate Circuit
Breakers 180 Degrees
for upflow right hand
return or downflow
left hand return
applications
Figure 1: Board
Layout
Figure
16: APSMA Module Layout
240VAC
to Pump(s)
240VAC
Power Source
240V IN 240V OUT
Representative drawing only, some models may vary in appearance.
Relay
Installing Electric Heater High Voltage Wires:
All wiring MUST be done in strict compliance with local, state,
national or any other applicable codes.
24VAC
connection
to unit #1
Note: If Electric Auxiliary is used, never disconnect power to the
heat unit as it may be required to properly heat the home.
Major damage may result.
24VAC
connection
to unit #2
24VAC 24VAC
(Y1 & C From Thermostat)
(Y1 & C From Thermostat)
Figure 2: Board
Schematic
Figure
17: APSMA
Please note, these heaters are for vertical units only.
Please see the Field-Installed Electric Heat IOM, part number
DC
27P009-01NN for detailed instructions on the installation and
Bridge
LED
wiring of auxiliary electric heaters.
+
24VAC input
from unit #1
24VAC input
from unit #2
Enertech Global
Relay
34
-
Module Wiring Schematic
Diode
RY1
RY1
240VAC input
RY2
+
-
Diode
RY2
240VAC to pump(s)
XT Models, Rev.: A
Section 10: Equipment Start-Up Procedures
Equipment Start-Up Process
Check the following before power is applied to the equipment
Caution: Do not start-up the unit until the new structure is ready to be occupied
Electrical:
… Geothermal unit high voltage
wiring is installed correctly
… Geothermal unit high voltage
wiring and breaker are the correct
size
… Auxiliary electric heaters are
wired and installed correctly
… Circulating pumps are wired and
fused (if necessary) correctly
… Desuperheater pump is NOT
wired, unless piping is complete
and all air is purged
… Low voltage wiring is correct and
completely installed
Plumbing:
… Pipe and pump sizes are correct
… Air is purged from all lines
… Antifreeze is installed
… All valves are open, including
those on the flow center
… Condensate is trapped and piped
to the drain
Ductwork:
… Filter is installed and clean
… Packaging is removed from the
blower assembly
… Blower turns freely
… Canvas connections installed on
supply plenum & return drop
Equipment Start-Up
1. Energize geothermal unit with
high voltage.
2. Set the thermostat to “Heat” or
“Cool.” Adjust set point to
energize the unit. System will
energize after delays expire
(typically a five minute delay).
3. Check water flow with a flow
meter (non-pressurized) or
pressure drop conversion
(pressurized). Pressure drop
tables must be used to convert
the pressure drop to GPM. The
pressure drop can be obtained by
checking water pressure in and
water pressure out at the P/T
ports.
4. Check the geothermal unit’s
electrical readings listed in the
Unit Electrical Data table.
5. Check the source water
temperature in and out at the P/T
ports (use insertion probe). Allow
10 minutes of operation before
recording temperature drop.
6. Calculate the heat of extraction or
heat of rejection.
7. Check the temperature difference
of the load coax (water-to-water)
or air coil (water-to-air). P/T ports
are recommended for use on the
load side, but the line
temperatures can be used to
check the temperature difference.
8. Change the mode of the
thermostat and adjust the set
point to energize the unit. Check
the data in opposite mode as the
previous tests. Amp draws as
well as temperature differences
and flow rate should be recorded.
9. Check auxiliary heat operation by
adjusting the thermostat set point
5°F above the room temperature
in “Heat” mode or set thermostat
to “Emergency." Record voltage,
amperage, and air temperature
difference.
EQUIPMENT START-UP FORM
Customer Name:_________________________________________________________________
Customer Address:_____________________________________________________________________________________
Model #:__________________________________________ Serial #:____________________________________________
Dealer Name:__________________________________________________________________________________________
Distributor Name:_____________________________________________ Start-up Date:____________________________
Loop Type: Open Closed (Circle One)
Flow Rate
Cooling
Heating
ut alothis
ng tline
his line
CutC
along
Source Water Pressure In
Source Water Pressure Out
Source Water Pressure Drop
Flow Rate
*Check pressure drop chart for GPM
PSI
PSI
PSI
GPM
Unit Electrical Data
PSI
PSI
PSI
GPM
Line Voltage
Total Unit Amps
Compressor Amps
Wire Size
Circuit Breaker Size
Source Water Temp. Difference
Cooling
Heating
Heat of Rejection/Extraction
Cooling
Heating
Source Water Temperature In
Source Water Temperature Out
Source Water Temperature Difference
Heat of Rejection
Heat Of Extraction
ºF
ºF
ºF
BTU/HR
Cooling
V
A
A
GA
A
Heating
A
A
ºF
ºF
ºF
BTU/HR
Heat of Extraction/Rejection = GPM X Water Temp. Difference X 500 (Water - Open Loop)
Heat of Extraction/Rejection = GPM X Water Temp. Difference X 485 (Water & Antifreeze - Closed Loop)
Load Water Temp. Difference
Load Water Temperature In
Load Water Temperature Out
Load Water Temperature Difference
Air Temperature Difference
Cooling
ºF
ºF
ºF
Cooling
Supply Air Temperature
ºF
ºF
Return Air Temperature
ºF
Air Temp. Difference
*Confirm auxiliary heaters are de-energized for the above readings.
Heating
ºF
ºF
ºF
Heating
Auxiliary Heat Operation Only
Heating
Auxiliary Heat Electrical Data
Heating
Supply Air Temperature
Return Air Temperature
Air Temp. Difference
Line Voltage
Total Amperage (Full kW - All Stages)
Wire Size
Breaker Size
CFM = (Watts X 3.413) ÷ (Air Temp. Difference X 1.08)
Watts = Volts X Auxiliary Heater Amps
ºF
ºF
ºF
ºF
ºF
ºF
V
A
GA
A
Installer/Technician:____________________________________________ Date:________________________
XT Models, Rev.: A
37
Enertech Global
Section 11: Troubleshooting
PERFORMANCE CHECK
Heat of Extraction(HE)/Rejection(HR)
Record information on the Unit Start-up Form
Equipment should be in full load operation for
a minimum of 10 minutes in either mode – WITH
THE HOT WATER GENERATOR TURNED OFF.
A 10% variance from Spec Manual is allowed.
Always use the same pressure gauge &
temperature measuring device.
Water flow must be in range of Specification
Manual. If system has too much water flow,
performance problems should be expected.
1. Determine flow rate in gallons per minute
a. Check entering water temperature
b. Check entering water pressure
c. Check leaving water pressure
Once this information is recorded, find
corresponding entering water temperature
column in Specification Manual for unit.
Find pressure differential in PSI column in Spec
Manual. Then read the GPM column in Spec
Manual to determine flow in GPM.
2. Check leaving water temperature of unit.
FORMULA: GPM x water temp diff, x 485
(antifreeze) or 500 (fresh water) = HE or HR in
BTU/HR
Enertech Global
38
XT Models, Rev.: A
Section 11: Troubleshooting
UNIT WILL NOT START IN EITHER CYCLE
Thermostat
Set thermostat on heating and highest temperature setting. Unit should run. Set thermostat on cooling and
lowest temperature setting. Unit should run. Set fan to On position. Fan should run. If unit does not run in
any position, disconnect wires at heat pump terminal block and jump R, G, Y. Unit should run in heating. If
unit runs, replace thermostat with correct thermostat only.
Loose or broken wires
Tighten or replace wires.
Blown Fuse/
Tripped Circuit Breakers
Check fuse size, replace fuse or reset circuit breaker.
Check low voltage circuit breaker.
Low Voltage Circuit
Check 24 volt transformer. If burned out or less than 24 volt, replace. Before replacing, verify tap setting
and correct if necessary.
BLOWER RUNS BUT COMPRESSOR WILL NOT START
(COMPRESSOR OVERLOAD, CAPACITOR BLOWN, HP FAULT)
Logic Board
Check if logic board is working properly. Check status light for fault. See board imprint for blink faults.
Flow Switch
Temporarily bypass flow switch until compressor starts. If compressor runs properly, check switch. If
defective, replace. If switch is not defective, check for air in loop system. Make sure loop system is
properly purged. Verify flow rate before changing switch.
Defective capacitor
Check capacitor. If defective, replace.
Frozen Compressor
See charts O and P for compressor diagnostic. If compressor still doesn’t run, replace it.
BLOWER RUNS BUT COMPRESSOR SHORT CYCLES OR DOES NOT RUN
Wiring
Loose or broken wires. Tighten or replace wires. See A: Unit will not start in either cycle.
Blown Fuse
Check fuse size. Check unit nameplate for correct sizing. Replace fuse or reset circuit breaker.
Check low voltage circuit breaker.
Flow Switch
Temporarily bypass flow switch for a couple seconds. If compressor runs properly, check switch. If
defective, replace. If switch is not defective, check for air in loop system. Make sure loop system is
properly purged. Verify flow rate before changing switch. .
Water Flow
If water flow is low (less than 3.5 GPM), unit will not start. Make sure Pump Module or solenoid valve is
connected (see wiring diagram). Water has to flow through the heat exchanger in the right direction (see
labels at water fitting connections) before the compressor can start. If water flow is at normal flow, use an
ohmmeter to check if you get continuity at the flow switch. If no switch is open and flow is a normal flow,
remove switch and check for stuck particles or bad switch.
High or low pressure switches
If heat pump is out on high or low-pressure cutout (lockout), check for faulty switches by jumping the
high and low-pressure switches individually. If defective replace. Check airflow, filters, water flow, loss of
refrigerant and ambient temperature. WARNING: Only allow compressor to run for a couple of seconds
with the high pressure switch jumpered
Defective logic board relay
Jump or bypass relay. If defective, replace.
Low refrigerant charge
Check for leaks and fix leaks.
NOISY BLOWER AND LOW AIR FLOW
Noisy Blower
Blower wheel contacting housing—Readjust.
Foreign material inside housing—Clean housing.
Loose duct work—Secure properly.
Low air flow
Check speed setting, check nameplate or data manual for proper speed, and correct speed setting.
Check for dirty air filter—Clean or replace; obstruction in system—Visually check.
Balancing dampers closed, registers closed, leaks in ductwork. Repair.
Ductwork too small. Resize ductwork.
UNIT RUNNING NORMAL, BUT SPACE TEMPERATURE IS UNSTABLE
Thermostat
XT Models, Rev.: A
Thermostat is getting a draft of cold or warm air. Make sure that the wall or hole used to run thermostat
wire from the ceiling or basement is sealed, so no draft can come to the thermostat.
Faulty Thermostat (Replace).
39
Enertech Global
Section 11: Troubleshooting
NO WATER FLOW
Pump Module
Make sure Pump Module is connected to the control box relay (check all electrical connections). For nonpressurized systems, check water level in Pump Module. If full of water, check pump. Close valve on the
pump flanges and loosen pump. Take off pump and see if there is an obstruction in the pump. If pump is
defective, replace. For pressurized systems, check loop pressure. Repressurize if necessary. May require
re-flushing if there is air in the loop.
Solenoid valve
Make sure solenoid valve is connected. Check solenoid. If defective, replace.
IN HEATING OR COOLING MODE, UNIT OUTPUT IS LOW
Water
Water flow & temperature insufficient.
Airflow
Check speed setting, check nameplate or data manual for proper speed, and correct speed setting.
Check for dirty air filter—Clean or replace.
Restricted or leaky ductwork. Repair.
Refrigerant charge
Refrigerant charge low, causing inefficient operation. Make adjustments only after airflow and water flow
are checked.
Reversing valve
Defective reversing valve can create bypass of refrigerant to suction side of compressor. Switch reversing
valve to heating and cooling mode rapidly. If problem is not resolved, replace valve. Wrap the valve with a
wet cloth and direct the heat away from the valve. Excessive heat can damage the valve. Always use dry
nitrogen when brazing. Replace filter/drier any time the circuit is opened.
Heat pump will not cool but will
heat. Heat pump will not heat
but will cool.
Reversing valve does not shift. Check reversing valve wiring. If wired wrong, correct wiring. If reversing
valve is stuck, replace valve. Wrap the valve with a wet cloth and direct the heat away from the valve.
Excessive heat can damage the valve. Always use dry nitrogen when brazing. Replace filter/drier any time
the circuit is opened.
Water heat exchanger
Check for high-pressure drop, or low temperature drop across the coil. It could be scaled. If scaled, clean
with condenser coil cleaner.
System undersized
Recalculate conditioning load.
WATER HEAT EXCHANGER FREEZES IN HEATING MODE
Water flow
Low water flow. Increase flow. See F. No water flow.
Flow Switch
Check switch. If defective, replace.
EXCESSIVE HEAD PRESSURE IN COOLING MODE
Inadequate water flow
Low water flow, increase flow.
EXCESSIVE HEAD PRESSURE IN HEATING MODE
Low air flow
See E: Noisy blower and low air flow.
AIR COIL FREEZES OVER IN COOLING MODE
Air flow
See E: Noisy blower and low air flow.
Blower motor
Motor not running or running too slow. Motor tripping off on overload. Check for overheated blower motor
and tripped overload. Replace motor if defective.
Panels
Panels not in place.
Low air flow
See E: Noisy blower and low air flow.
WATER DRIPPING FROM UNIT
Unit not level
Level unit.
Condensation drain line plugged
Unplug condensation line.
Water sucking off the air coil in
cooling mode
Too much airflow. Duct work not completely installed. If duct work is not completely installed, finish duct
work. Check static pressure and compare with air flow chart in spec manual under specific models section.
If ductwork is completely installed it may be necessary to reduce CFM.
Water sucking out of the
drain pan
Install an EZ-Trap or P-Trap on the drain outlet so blower cannot suck air back through the drain outlet.
Enertech Global
40
XT Models, Rev.: A
Section 11: Troubleshooting
COMPRESSOR WON’T START
Check for proper
compressor nameplate
voltage.
OK
Does Compressor draw
current when voltage is Yes
applied.
Are the suction &
discharge pressures
balanced.
No
Attempt to restart
the compressor
OK
Check voltage supply
& contactor operation.
OK
No
Check motor
resistance.
(See Note B)
Allow time for
compressor to
balance.
OK
Voltage supply
is too low.
Yes
Allow time for the
protector to reset.
No
Compressor
Connection Block
Is the voltage 197
or higher when the
compressor is trying
to start.
Yes
C
Yes
OK
Recheck Resistance
R
Not
OK
OK
Allow to start the
compressor while
measuring voltage
on the load side of
the contactor.
Not
OK
Is the compressor
hot?
No
Check the wiring,
capacitor & contactor
operation. (See Note A)
Yes
If the compressor
fails to start after
3 attempts, replace
the compressor.
S
Single Phase 208-230
C = Line Winding
R = Run Winding
S = Start Winding
Replace Compressor
A: Check all terminals, wires & connections for loose or burned wires and connections. Check contactor and 24 Volt
coil. Check capacitor connections & check capacitor with capacitor tester.
B: If ohm meter reads 0 (short) resistance from C to S, S to R, R to C or from anyone of one of these terminals to
ground (shorted to ground), compressor is bad.
COMPRESSOR WON’T PUMP CHART
Is th e c o m p re s s o r
ru n n in g ?
Y es
M e a s u re & re c o rd
th e a m p s, v o lts ,
s u c ti o n & d is c h a rg e
p re s s u re .
OK
D o e s th e u n it
h a v e a re frig e ra n t
c h a rg e ?
S h u t th e u n it d o w n &
re v e rs e th e p h a s in g
(3 - P h a s e O n ly )
OK
No
No
R e fe r to th e c o m p re s s o r
w o n 't s ta rt flo w c h a rt.
Y es
C h e c k & v e rify
th e ru n c a p a c ito r
A d d re frig e ra n t
to th e s y s te m .
OK
If th e c o m p re s s o r
s till w o n 't p u m p
re p la c e c o m p re s s o r.
XT Models, Rev.: A
41
OK
C h e c k th e o p e ra tio n
o f th e re v e rs in g
v a lv e .
Enertech Global
Section 11: Troubleshooting
Customer/Job Name:____________________________________________ Date:________________________________
Model #:__________________________________________ Serial #:____________________________________________
Antifreeze Type:____________________________________
Suction
Discharge
Heating
Mode
°F
Return Air
Air Coil
42
Discharge
°F
Supply Air
Air Coil
Coax
Enertech Global
psi
°F
GPM
Cooling
Mode
psi
Source (loop) IN
Optional desuperheater
installed in discharge line
(always disconnect during
troubleshooting)
psi
°F
Discharge Line (saturation)
psi
°F
Suction Line (saturation)
°F
Suction temp
Filter Drier
°F
Liquid line (cooling)
To suction line
Reversing
Valve
Air Coil
To suction line bulb
TXV
Suction
°F
Liquid line (heating)
Coax
Cut along this line
°F
SH = Suction Temp. - Suction Sat.
SC = Disch. Sat. - Liq. Line Temp.
Source (loop) OUT
Source
Coax
HE or HR = GPM x TD x Fluid Factor
(Use 500 for water; 485 for antifreeze)
XT Models, Rev.: A
Section 11: Engineering Data
Unit Electrial Data
NOTE: Proper Power
A Supply Evaluation
⚠ CAUTION ⚠
When any compressor bearing unit is connected to a weak
power supply, starting current will generate a significant “sag” in
the voltage which reduces the starting torque of the compressor
motor and increases the start time. This will influence the rest of
the electrical system in the building
EP by lowering the voltage to
ELthe
lights. This momentary low voltage causes “light dimming”. The
total electrical system should be evaluated with an electrician and
HVAC technician. The evaluation should include all connections,
NEUTRAL OR
sizes of wires, and size of the distribution panel between the
GROUNDconnection and
unit and the utility’s connection. The transformer
sizing shouldEbe evaluated by the electric utility provider.
CHECK COMPRESSOR AMP DRAW TO
VERIFY COMPRESSOR ROTATION ON THREE
PHASE UNITS. COMPARE AGAINST UNIT
ELECTRICAL TABLES. REVERSE ROTATION
RESULTS IN HIGHER SOUND LEVELS,
LOWER AMP DRAW, AND INCREASED
COMPRESSOR WEAR. THE COMPRESSOR
INTERNAL OVERLOAD WILL TRIP AFTER A
SHORT PERIOD OF OPERATION.
P
EP
B
C
Example 1: WYE (STAR) Electrical Circuit
Example 2: DELTA Electrical Circuit
A
EL
IP
EP
EL
EL
NEUTRAL OR
GROUND
EP
EP
EP
EL
EP
C
EL
B
EL
EP
EL
IP
⚠ CAUTION ⚠
ALL VOLTAGE CODE “3” 460V UNITS UTILIZE
A 277V ECM MOTOR WHICH REQUIRES A
NEUTRAL WIRE. THE MOTORS ARE WIRED
BETWEEN THE NEUTRAL AND ONE HOT LEG
OF THE CIRCUIT. SOURCE WIRING MUST BE
WYE (STAR) CONFIGURATION. 3-PHASE
DELTA CONNECTIONS WILL NOT PROVIDE
THE CORRECT WIRING AND WILL CAUSE
THE UNIT NOT TO OPERATE.
EL
EP
EP
EL
EP
XT Models, Rev.: A
EL
EL
43
Enertech Global
Section 11: Engineering Data
Unit Electrial Data
Model
024
036
048
060
072
60Hz Power
Compressor
Volts
Phase
LRA
RLA
ECM
Fan
Motor
FLA
1
208/230
1
58.3
11.7
3.9
0.5
4.0
20.1
23.0
35
12
49
0
208/230
1
58.3
11.7
3.9
N/A
N/A
15.6
18.5
30
14
41
2
208/230
3
55.4
6.5
3.9
N/A
N/A
10.4
12.0
15
14
62
3
460
3
28.0
3.5
3.9
N/A
N/A
7.4
8.4
10
14
87
1
208/230
1
83.0
15.3
3.9
0.5
4.0
23.7
27.5
40
10
70
0
208/230
1
83.0
15.3
3.9
N/A
N/A
19.2
23.0
35
12
52
2
208/230
3
73.0
11.6
3.9
N/A
N/A
15.5
18.4
30
14
41
3
460
3
38.0
5.7
3.9
N/A
N/A
9.6
11.0
15
14
67
1
208/230
1
104.0
21.2
5.2
0.5
5.5
32.4
37.7
50
8
79
0
208/230
1
104.0
21.2
5.2
N/A
N/A
26.4
31.7
50
8
97
2
208/230
3
83.1
14.0
5.2
N/A
N/A
19.2
22.7
35
12
52
3
460
3
41.0
6.4
5.2
N/A
N/A
11.6
13.2
20
14
55
1
208/230
1
152.9
27.1
6.9
0.5
5.5
40.0
46.8
70
6
102
0
208/230
1
152.9
27.1
6.9
N/A
N/A
34.0
40.8
60
6
120
2
208/230
3
110.0
16.5
6.9
N/A
N/A
23.4
27.5
40
10
71
3
460
3
52.0
7.2
6.9
N/A
N/A
14.1
15.9
20
14
45
1
208/230
1
179.2
29.7
6.9
0.5
5.5
42.6
50.0
80
6
95
0
208/230
1
179.2
29.7
6.9
N/A
N/A
36.6
44.0
70
6
111
2
208/230
3
136.0
17.6
6.9
N/A
N/A
24.5
28.9
45
10
68
3
460
3
66.1
8.5
6.9
N/A
N/A
15.4
17.5
25
14
41
Voltage
Code
HWG
Pump
FLA
Ext
Loop
Pump
FLA*
Total
Unit
FLA
Min
Circuit
AMPS
Max
Fuse
HACR
Min
AWG
Max
Ft
Notes:
1. All line and low voltage wiring must adhere to the National Electrical Code and local codes, whichever is the most stringent.
2. Wire length based on a one way measurement with a 2% voltage drop.
3. Wire size based on 60°C copper conductor and minimum circuit ampacity.
3. All fuses class RK-5.
4. Min/Max Voltage: 208/230/60/1 = 187-252, 208/230/60/3 = 187-252, 460/60/3 = 432-504
5. See Example Electrical Circuits for proper 460V power
* The external loop pump FLA is based on a maximum of three UP26-116F-230V pumps (1/2hp) for 048 - 072 and two pumps for 024 - 036.
Enertech Global
44
XT Models, Rev.: A
Section 11: Engineering Data
Water Flow Calculations and Selection
Proper flow rate is crucial for reliable operation of geothermal heat
pumps. The performance data shows three flow rates for each entering
water temperature (EWT column). The general “rule of thumb” when
selecting flow rates is the following:
Top flow rate: Open loop systems (1.5 to 2.0 gpm per ton)
Middle flow rate: Minimum closed loop system flow rate
(2.25 to 2.50 gpm/ton)
Bottom flow rate: Nominal (optimum) closed loop system flow rate
(3.0 gpm/ton)
Although the industry standard is adequate in most areas of North
America, it is important to consider the application type before applying
this “rule of thumb.” Antifreeze is generally required for all closed loop
(geothermal) applications. Extreme Southern U.S. locations are the
only exception. Open loop (well water) systems cannot use antifreeze,
and must have enough flow rate in order to avoid freezing conditions at
the Leaving Source Water Temperature (LWT) connection.
Calculations must be made for all systems without antifreeze to determine
if the top flow rate is adequate to prevent LWT at or near freezing
conditions. The following steps should be taken in making this calculation:
Determine minimum EWT based upon your geographical area.
Go to the performance data table for the heat pump model selected and
look up the the Heat of Extraction (HE) at the “rule of thumb” water flow
rate (GPM) and at the design Entering Air Temperature (EAT).
Calculate the temperature difference (TD) based upon the HE and GPM
of the model.
TD = HE / (GPM x 500).
Calculate the LWT.
LWT = EWT - TD.
If the LWT is below 35-38°F, there is potential for freezing conditions if
the flow rate or water temperature is less than ideal conditions, and the
flow rate must be increased.
Example 1:
EWT = 50°F.
Model GXT048, high capacity. Flow rate = 6 GPM.
Air Flow = 1500 CFM. HE = 36,700 Btuh.
TD = 36,700 / (6 x 500) = 12.2°F
LWT = 50 - 12.2 = 37.8°F
Since the water flow is leaving at approximately 38°F, the flow rate
is acceptable.
Example 2:
EWT = 40°F.
Model GXT048, high capacity. Flow rate = 6 GPM.
Air Flow = 1500 CFM. HE = 36,700 Btuh.
TD = 36,700 / (6 x 500) = 12.2°F
LWT = 40 - 12.2 = 27.8°F
Water flow rate must be increased to avoid freezing.
Performance Data Notes
1. Capacity data is based upon 15% (by volume) methanol antifreeze solution.
2. Desuperheater capacity is based upon 0.4 GPM Flow per nominal ton at 90°F entering hot water temperature.
3. Interpolation between above categories is permissible; extrapolation is not.
4. See Flow Rate Selection above for proper application.
XT Models, Rev.: A
45
Enertech Global
Section 11: Engineering Data
Glossary of Terms
CFM = Airflow, Cubic Feet/Minute
HR = Total Heat Of Rejection, Btu/hr
COP = Coefficient of Performance = BTU Output / BTU Input
KW = Total Power Unit Input, Kilowatts
DH = Desuperheater Capacity, Btu/hr
LAT = Leaving Air Temperature, Fahrenheit
EAT = Entering Air Temperature, Fahrenheit (Dry Bulb/Wet Bulb)
LC = Latent Cooling Capacity, Btu/hr
EER = Energy Efficiency Ratio = BTU output/Watts input
SC = Sensible Cooling Capacity, Btu/hr
EWT = Entering Source Water Temperature, Fahrenheit
LWT = Leaving Source Water Temperature, Fahrenheit
ELT = Entering Load Water Temperature, Fahrenheit
LLT = Leaving Load Water Temperature, Fahrenheit
GPM = Water Flow, Gallons Per Minute
TC = Total Cooling Capacity, Btu/hr
HC = Total Heating Capacity, Btu/hr
WPD = Water Pressure Drop, PSI & Feet of Water
HE = Total Heat Of Extraction, Btu/hr
Heating & Cooling Calculations
Heating
LAT = EAT +
Cooling
HC
CFM x 1.08
LWT = EWT -
LAT (DB) = EAT (DB) -
HE
GPM x 500
LWT = EWT +
SC
CFM x 1.08
HR
GPM x 500
LC = TC - SC
Performance Data Correction Factors
Heating Correction Factors - Full Load
EAT °F
HC
50
1.0450
60
1.0260
55
65
70
75
80
1.0347
1.0089
1.0000
0.9924
0.9870
HE
1.1136
55
1.0640
1.0270
1.0000
0.9653
70
0.8635
0.9701
0.9715
0.9774
75
1.0446
1.1179
1.0425
1.1124
65
70
75
80
0.9205
1.0000
1.0335
1.0878
EAT
(WB) °F
HE
1.0480
kW
1.1240
1.0355
0.7839
1.0943
1.0246
1.0126
0.8305
1.0650
0.8837
1.0000
1.0000
1.0330
1.0000
0.9866
0.9411
0.9661
0.9613
70
75
55
1.201
1.289
63
0.852
0.995
60
65
67
70
75
Enertech Global
HC
1.0579
0.9325
1.0513
Sensible Cooling Correction Factors
0.8293
1.0000
60
1.0522
0.8215
1.0000
50
1.0527
kW
67
65
55
1.0000
0.9741
0.9001
0.8567
0.9497
HR
0.8955
EAT °F
0.9019
TC
60
kW
0.8208
1.0892
Cooling Correction Factors
EAT
(WB) °F
Heating Correction Factors - Part Load
46
0.943
0.797
0.624
EAT (DB) °F
80
85
1.067
1.192
0.952
1.106
1.261
0.820
0.944
0.812
0.697
1.138
1.000
0.637
90
1.188
1.343
0.817
0.983
1.067
XT Models, Rev.: A
Section 11: Engineering Data
AHRI Performance Data
Ground Loop Heat Pump
MODEL
XT024
XT036
XT048
XT060
XT072
CAPACITY
Full Load
Part Load
Full Load
Part Load
Full Load
Part Load
Full Load
Part Load
Full Load
Part Load
HEATING
Btu/hr
COP
19,800
4.3
16,600
4.8
29,200
4.2
23,200
4.6
38,200
3.9
29,700
4.3
47,700
3.7
38,600
4.3
55,900
3.6
46,700
4.1
COOLING
Btu/hr
EER
27,200
20.3
21,400
29.1
38,900
18.3
29,900
27.0
49,000
17.1
37,400
24.1
63,000
17.8
49,000
24.9
71,100
17.1
57,500
23.0
Note:
Rated in accordance with ISO Standard 13256-1 which includes Pump Penalties.
Heating capacities based on 68.0°F DB, 59.0°F WB entering air temperature.
Cooling capacities based on 80.6°F DB, 66.2°F WB entering air temperature.
Entering water temperatures Full Load: 32°F heating / 77°F cooling.
Entering water temperatures Part Load: 41°F heating / 68°F cooling.
Ground Water Heat Pump
MODEL
XT024
XT036
XT048
XT060
XT072
CAPACITY
Full Load
Part Load
Full Load
Part Load
Full Load
Part Load
Full Load
Part Load
Full Load
Part Load
HEATING
Btu/hr
COP
24,600
5.3
18,200
5.5
35,700
4.9
24,800
5.3
47,700
4.5
34,000
4.9
60,000
4.5
43,300
4.8
70,300
4.3
52,800
4.6
COOLING
Btu/hr
EER
29,600
26.9
22,400
34.0
40,900
23.4
30,400
32.8
53,600
22.5
39,800
29.6
67,700
22.4
50,800
29.8
75,600
21.1
59,200
26.9
Note:
Rated in accordance with ISO Standard 13256-1 which includes Pump Penalties.
Heating capacities based on 68.0°F DB, 59.0°F WB entering air temperature.
Cooling capacities based on 80.6°F DB, 66.2°F WB entering air temperature.
Entering water temperatures: 50°F heating / 59°F cooling.
XT Models, Rev.: A
47
Enertech Global
Section 11: Engineering Data
Model 024 Part Load Heating Performance Data: 2.0 Ton
Heating
LWT
EWT Flow WPD
Airflow LAT
HC
HE
COP Discharge Suction Subcooling Superheat
°F
GPM PSI FT
°F
CFM
°F
MBtuh MBtuh kW
W/W
PSIG
PSIG
°F
°F
20.3
700
87.5
13.3
9.1
1.21
3.22
278.0
86.5
18.3
9.4
25
4.0 2.4 5.6
20.3
750
86.4
13.3
9.2
1.20
3.26
275.0
86.4
18.2
9.3
20.9
700
87.1
12.9
8.8
1.19
3.17
274.0
84.6
17.2
10.8
2.0 0.7 1.6
20.9
750
85.8
12.8
8.8
1.18
3.17
271.0
84.2
17.2
10.8
23.3
700
88.3
13.8
9.7
1.20
3.36
279.0
89.2
17.4
10.1
30
3.0 1.4 3.3
23.3
750
87.1
13.8
9.8
1.19
3.40
276.0
89.1
17.3
10.1
24.8
700
88.9
14.3
10.2
1.21
3.47
282.0
92.0
17.3
9.9
4.0 2.4 5.5
24.7
750
87.7
14.4
10.3
1.20
3.51
278.0
91.9
17.1
9.8
28.8
700
89.8
15.0
10.8
1.22
3.60
286.0
95.6
17.3
9.6
2.0 0.7 1.6
28.8
750
88.5
15.0
10.9
1.20
3.65
282.0
95.4
17.3
9.5
32.0
700
90.9
15.8
11.6
1.23
3.77
292.0
101.2
17.3
9.4
3.0 1.4 3.2
40
31.9
750
89.6
15.8
11.7
1.21
3.84
286.0
101.0
16.2
9.4
33.6
700
92.0
16.6
12.4
1.23
3.96
295.0
105.1
16.4
9.3
4.0 2.3 5.2
33.5
750
90.6
16.7
12.5
1.22
4.02
290.0
104.9
16.3
9.2
37.0
700
92.3
16.8
12.6
1.24
3.99
297.0
107.2
16.2
9.1
2.0 0.7 1.5
36.9
750
90.8
16.9
12.7
1.22
4.05
292.0
106.9
16.2
9.0
40.4
700
94.2
18.3
14.0
1.25
4.29
305.0
114.8
16.3
9.5
50
3.0 1.3 3.0
40.3
750
92.6
18.3
14.1
1.23
4.36
300.0
114.5
16.3
9.4
42.4
700
95.2
19.0
14.7
1.26
4.43
310.0
119.2
16.3
9.7
4.0 2.2 5.0
42.3
750
93.6
19.1
14.9
1.24
4.52
305.0
119.0
16.4
9.6
44.9
700
95.0
18.9
14.6
1.26
4.42
310.0
119.9
15.4
9.2
2.0 0.6 1.4
44.8
750
93.4
19.0
14.7
1.24
4.50
304.0
119.5
15.3
9.2
48.9
700
97.1
20.5
16.2
1.27
4.75
318.0
129.2
14.3
10.1
60
3.0 1.3 2.9
48.8
750
95.4
20.6
16.3
1.24
4.85
312.0
128.8
14.3
10.1
51.2
700
98.2
21.3
17.0
1.27
4.91
324.0
134.5
14.4
10.7
4.0 2.1 4.8
51.2
750
96.4
21.4
17.1
1.25
5.02
317.0
134.2
14.2
10.6
52.8
700
97.8
21.0
16.7
1.27
4.85
322.0
133.9
13.3
9.5
2.0 0.6 1.4
52.7
750
96.0
21.1
16.8
1.25
4.96
315.0
133.4
13.3
9.4
57.4
700
100.1
22.7
18.3
1.28
5.19
334.0
145.1
13.4
10.6
70
3.0 1.2 2.8
57.3
750
98.2
22.8
18.5
1.26
5.31
326.0
144.6
13.3
10.6
60.0
700
101.4
23.8
19.3
1.29
5.38
340.0
151.5
13.4
11.6
4.0 2.0 4.6
59.9
750
99.4
23.8
19.5
1.26
5.53
331.0
151.2
12.3
11.5
60.4
700
100.9
23.4
19.0
1.29
5.33
337.0
149.8
12.5
9.3
2.0 0.6 1.4
60.3
750
98.9
23.4
19.2
1.26
5.46
329.0
149.1
12.4
9.3
65.8
700
103.2
25.1
20.7
1.30
5.65
350.0
162.9
12.5
10.9
80
3.0 1.2 2.7
65.7
750
101.1
25.2
20.8
1.27
5.82
340.0
162.4
11.4
10.9
68.9
700
104.5
26.1
21.6
1.31
5.84
356.0
170.6
11.5
11.9
4.0 2.0 4.5
68.7
750
102.4
26.2
21.9
1.28
6.02
347.0
170.1
11.3
11.9
68.3
700
103.7
25.5
21.1
1.30
5.77
350.0
166.9
10.3
9.4
2.0 0.6 1.3
68.1
750
101.6
25.6
21.3
1.27
5.93
342.0
166.1
10.4
9.4
73.8
700
106.8
27.8
23.5
1.25
6.54
346.0
181.4
10.4
11.1
3.0 1.2 2.7
90
73.6
750
104.5
27.9
23.8
1.21
6.75
336.0
180.1
10.3
11.4
77.3
700
108.2
28.9
24.7
1.25
6.80
352.0
190.9
9.4
12.5
4.0 1.9 4.4
77.2
750
105.8
29.0
24.9
1.21
7.02
342.0
189.8
9.3
12.5
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
Enertech Global
48
XT Models, Rev.: A
Section 11: Engineering Data
Model 024 Full Load Heating Performance Data: 2.0 Ton
Heating
LWT Aiflow LAT
EWT
Flow
WPD
HC
HE
COP
Discharge Suction Subcooling Superheat
°F
GPM
PSI
FT
°F
CFM
°F
MBtuh MBtuh kW
W/W
PSIG
PSIG
°F
°F
20.3
850
90.4
18.7
13.6
1.49
3.68
288.9
76.1
20.5
8.6
25
6.0
4.6
10.5
20.3
950
88.3
18.8
13.7
1.49
3.70
287.1
76.2
20.4
8.6
20.9
850
89.8
18.2
13.3
1.45
3.68
282.2
74.0
19.5
10.1
3.0
1.6
3.6
20.8
950
87.8
18.3
13.4
1.45
3.70
280.4
74.1
19.3
10.0
23.5
850
90.8
19.1
14.1
1.48
3.78
287.6
78.3
19.4
9.8
30
4.5
2.9
6.6
23.5
950
88.7
19.2
14.2
1.48
3.80
285.8
78.4
19.2
9.7
24.9
850
91.5
19.7
14.7
1.48
3.90
289.9
80.6
19.3
9.7
6.0
4.5
10.3
24.9
950
89.3
19.8
14.8
1.48
3.92
288.1
80.7
19.1
9.7
29.1
850
92.9
21.0
15.9
1.50
4.10
295.0
87.1
19.0
9.7
3.0
1.5
3.4
29.0
950
90.6
21.1
16.0
1.49
4.15
293.2
87.2
18.9
9.6
32.3
850
94.1
22.1
16.9
1.53
4.23
300.7
92.2
18.9
9.9
40
4.5
2.7
6.2
32.2
950
91.6
22.2
17.0
1.52
4.28
298.8
92.3
18.7
9.8
34.0
850
94.7
22.7
17.5
1.53
4.35
303.1
94.9
18.7
10.0
6.0
4.2
9.7
34.0
950
92.2
22.8
17.6
1.52
4.40
301.3
95.0
18.5
10.0
37.3
850
95.9
23.8
18.5
1.55
4.50
308.6
101.0
18.3
9.8
3.0
1.4
3.2
37.2
950
93.3
23.9
18.6
1.54
4.55
306.7
101.1
18.2
9.8
41.0
850
97.3
25.1
19.7
1.58
4.66
314.5
106.9
18.1
10.6
50
4.5
2.5
5.8
40.9
950
94.6
25.2
19.8
1.57
4.70
312.6
107.0
18.0
10.5
43.0
850
98.0
25.7
20.3
1.58
4.77
317.1
110.0
17.9
11.0
6.0
3.9
9.1
43.0
950
95.2
25.9
20.5
1.57
4.83
315.1
110.1
17.8
10.9
45.6
850
98.6
26.3
20.9
1.59
4.85
319.6
114.7
16.8
10.6
3.0
1.3
3.0
45.6
950
95.7
26.4
21.0
1.58
4.90
317.6
114.7
16.8
10.6
49.8
850
100.2 27.7
22.2
1.62
5.01
325.7
121.4
16.6
11.8
60
4.5
2.4
5.5
49.7
950
97.2
27.9
22.4
1.61
5.08
323.7
121.4
16.5
11.8
52.1
850
101.0 28.5
23.0
1.62
5.16
328.3
124.9
16.4
12.6
6.0
3.7
8.6
52.1
950
97.9
28.6
23.1
1.61
5.21
326.3
125.0
16.2
12.6
54.0
850
101.5 28.9
23.3
1.64
5.16
332.3
130.3
15.2
11.3
3.0
1.3
2.9
53.8
950
98.4
29.1
23.5
1.64
5.20
330.3
130.4
15.1
11.2
58.6
850
103.2 30.5
24.8
1.68
5.32
338.7
137.9
14.8
12.9
4.5
2.3
5.3
70
58.6
950
99.8
30.6
24.9
1.67
5.37
336.6
137.9
14.7
12.9
61.2
850
104.1 31.3
25.6
1.68
5.46
341.4
141.9
14.5
13.9
6.0
3.6
8.3
61.1
950
100.7 31.5
25.8
1.67
5.53
339.3
142.0
14.4
13.9
62.1
850
104.9 32.0
26.1
1.74
5.39
350.7
149.5
13.8
11.3
3.0
1.2
2.8
62.0
950
101.3 32.1
26.2
1.73
5.44
348.5
149.5
13.8
11.3
67.3
850
106.7 33.7
27.7
1.77
5.58
357.4
158.1
13.3
13.6
80
4.5
2.2
5.1
67.3
950
102.9 33.8
27.8
1.77
5.60
355.2
158.2
13.2
13.5
70.2
850
107.7 34.6
28.6
1.77
5.73
360.3
162.8
12.9
14.7
6.0
3.4
7.9
70.1
950
103.9 34.8
28.8
1.77
5.76
358.1
162.8
12.8
14.7
70.2
850
108.2 35.1
28.8
1.85
5.56
369.8
169.4
12.1
11.8
3.0
1.1
2.7
70.1
950
104.3 35.2
28.9
1.84
5.61
367.5
169.5
12.0
11.8
76.0
850
110.2 36.9
30.5
1.88
5.75
376.9
179.2
11.4
14.4
4.5
2.1
4.8
90
75.9
950
106.2 37.1
30.7
1.87
5.81
374.6
179.3
11.4
14.3
79.2
850
111.3 37.9
31.5
1.88
5.91
379.9
184.5
11.0
15.8
6.0
3.3
7.5
79.1
950
107.1 38.1
31.7
1.87
5.97
377.6
184.6
11.0
15.8
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
XT Models, Rev.: A
49
Enertech Global
Section 11: Engineering Data
Model 024 Part Load Cooling Performance Data: 2.0 Ton
Cooling
LWT Airflow
TC
SC
HR
EER
Discharge Suction Subcooling Superheat
°F
CFM MBtuh MBtuh S/T MBtuh kW Btuh/W
PSIG
PSIG
°F
°F
75.5
700
21.4
15.2 0.71 24.7 0.97
22.1
240.0
150.6
15.6
17.7
2.0 0.6 1.5
75.7
750
21.6
15.7 0.73 25.0 0.97
22.3
241.0
152.6
15.4
16.9
67.5
700
22.7
15.7 0.69 25.5 0.81
27.9
189.0
147.7
11.3
18.1
50
3.0 1.3 3.0
67.7
750
22.9
16.3 0.71 25.7 0.81
28.3
190.0
149.6
11.4
17.5
63.3
700
23.1
15.8 0.69 25.7 0.77
30.0
174.0
146.6
10.2
18.4
4.0 2.2 5.0
63.4
750
23.3
16.4 0.70 25.9 0.77
30.4
175.0
148.8
9.4
17.8
85.1
700
20.8
15.2 0.73 24.3 1.04
20.0
263.0
152.8
15.5
14.8
2.0 0.6 1.4
85.3
750
21.0
15.7 0.75 24.5 1.04
20.1
264.0
154.6
15.5
14.1
77.1
700
21.7
15.5 0.71 24.9 0.91
23.8
222.0
150.7
12.2
15.3
60
3.0 1.3 2.9
77.2
750
21.9
16.1 0.73 25.0 0.91
24.1
223.0
152.6
11.5
14.7
72.9
700
22.1
15.6 0.70 25.1 0.86
25.6
206.0
149.9
10.3
15.4
4.0 2.1 4.9
73.0
750
22.4
16.2 0.72 25.3 0.86
26.0
207.0
151.8
10.4
14.7
94.6
700
20.0
15.0 0.75 23.9 1.15
17.5
294.0
155.1
16.5
12.1
2.0 0.6 1.4
94.8
750
20.1
15.5 0.77 24.0 1.14
17.6
295.0
157.1
15.6
11.2
86.6
700
20.7
15.2 0.74 24.2 1.03
20.1
259.0
153.6
12.5
12.8
70
3.0 1.2 2.9
86.7
750
20.8
15.7 0.76 24.3 1.02
20.4
259.0
155.5
11.5
12.0
82.6
700
21.0
15.3 0.73 24.3 0.97
21.7
241.0
152.9
10.3
13.1
4.0 2.1 4.7
82.6
750
21.2
15.9 0.75 24.5 0.97
21.9
242.0
154.7
9.6
12.3
104.1
700
19.0
14.7 0.77 23.3 1.28
14.8
335.0
157.6
16.7
11.1
2.0 0.6 1.4
104.2
750
19.1
15.2 0.80 23.4 1.28
14.9
335.0
159.3
15.6
10.4
96.2
700
19.6
14.8 0.75 23.5 1.16
16.9
298.0
156.3
12.5
11.6
80
3.0 1.2 2.8
96.2
750
19.7
15.5 0.79 23.6 1.15
17.1
298.0
157.9
11.5
11.2
92.2
700
19.9
14.9 0.75 23.7 1.10
18.2
280.0
155.5
10.5
11.7
4.0 2.0 4.7
92.3
750
20.1
15.6 0.78 23.8 1.09
18.4
281.0
157.0
10.5
11.4
113.4
700
17.8
14.2 0.80 22.7 1.44
12.4
378.0
160.1
15.7
10.9
2.0 0.6 1.4
113.6
750
18.0
14.8 0.82 22.9 1.44
12.5
379.0
161.6
15.7
10.2
105.8
700
18.5
14.4 0.78 22.9 1.31
14.2
341.0
158.7
12.5
11.6
90
3.0 1.2 2.8
105.8
750
18.6
15.1 0.81 23.0 1.31
14.2
342.0
159.8
12.6
11.3
101.9
700
18.8
14.5 0.77 23.1 1.24
15.1
324.0
157.8
11.7
11.8
4.0 2.0 4.7
102.0
750
19.0
15.1 0.80 23.2 1.24
15.3
323.0
159.6
10.5
11.1
122.9
700
16.8
13.8 0.82 22.2 1.61
10.4
426.0
162.4
15.8
10.9
2.0 0.6 1.4
122.9
750
16.8
14.5 0.86 22.3 1.60
10.5
425.0
163.7
14.7
10.5
115.4
700
17.3
14.0 0.81 22.4 1.47
11.8
388.0
161.1
12.6
11.7
100
3.0 1.2 2.8
115.5
750
17.5
14.6 0.84 22.5 1.47
11.9
389.0
162.4
12.7
11.0
111.6
700
17.7
14.2 0.80 22.5 1.41
12.5
370.0
160.1
11.6
12.2
4.0 2.0 4.7
111.6
750
17.7
14.7 0.83 22.5 1.40
12.7
370.0
161.8
10.7
11.3
132.4
700
15.6
13.4 0.86 21.8 1.80
8.7
477.0
164.5
15.7
11.7
2.0 0.6 1.4
132.5
750
15.7
14.1 0.89 21.9 1.80
8.8
478.0
165.8
15.6
10.9
125.0
700
16.2
13.6 0.84 21.8 1.66
9.8
439.0
163.1
12.6
12.5
3.0 1.2 2.9
110
125.0
750
16.2
14.2 0.87 21.9 1.65
9.8
439.0
164.7
11.7
11.6
121.3
700
16.5
13.7 0.83 21.9 1.59
10.4
422.0
162.5
11.8
12.7
4.0 2.1 4.8
121.3
750
16.5
14.3 0.86 21.9 1.58
10.4
420.0
164.0
10.6
11.8
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
EWT
°F
Flow WPD
GPM PSI FT
Enertech Global
50
XT Models, Rev.: A
Section 11: Engineering Data
Model 024 Full Load Cooling Performance Data: 2.0 Ton
Cooling
LWT
EWT Flow
WPD
Aiflow TC
SC
HR
EER
°F
GPM
PSI
FT
°F
CFM MBtuh MBtuh S/T MBtuh kW
Btuh/W
73.2
850
29.7
19.0
0.64
33.8
1.21
24.5
3.0
1.7
3.9
73.8
950
30.5
20.4
0.67
34.7
1.23
24.8
65.5
850
30.0
19.1
0.64
33.9
1.14
26.3
50
4.5
2.7
6.2
65.9
950
30.8
20.5
0.67
34.8
1.16
26.6
61.6
850
30.1
19.3
0.64
33.9
1.11
27.1
6.0
3.9
8.9
62.0
950
30.9
20.7
0.67
34.8
1.13
27.3
82.9
850
28.7
18.8
0.66
33.3
1.35
21.3
3.0
1.6
3.7
83.4
950
29.4
20.2
0.69
34.1
1.38
21.3
75.3
850
29.0
18.9
0.65
33.3
1.27
22.8
60
4.5
2.5
5.9
75.7
950
29.8
20.3
0.68
34.2
1.30
22.9
71.4
850
29.1
19.1
0.66
33.3
1.24
23.5
6.0
3.7
8.5
71.8
950
29.9
20.5
0.69
34.2
1.26
23.7
92.5
850
27.7
18.6
0.67
32.8
1.50
18.5
3.0
1.5
3.5
93.1
950
28.4
20.0
0.70
33.6
1.53
18.6
85.0
850
28.0
18.7
0.67
32.8
1.41
19.9
70
4.5
2.4
5.6
85.4
950
28.7
20.1
0.70
33.6
1.44
19.9
81.3
850
28.1
18.9
0.67
32.8
1.37
20.5
6.0
3.5
8.0
81.5
950
28.8
20.3
0.70
33.6
1.40
20.6
101.9 850
26.3
18.0
0.68
31.9
1.64
16.0
3.0
1.5
3.4
102.4 950
26.9
19.3
0.72
32.6
1.67
16.1
94.6
850
26.5
18.0
0.68
31.8
1.55
17.1
80
4.5
2.4
5.4
94.9
950
27.2
19.4
0.71
32.6
1.58
17.2
90.9
850
26.6
18.2
0.68
31.7
1.50
17.7
6.0
3.4
7.8
91.2
950
27.3
19.6
0.72
32.5
1.53
17.8
111.2 850
24.7
17.2
0.70
30.8
1.80
13.7
3.0
1.4
3.3
111.7 950
25.3
18.5
0.73
31.6
1.84
13.8
104.1 850
25.0
17.3
0.69
30.8
1.70
14.7
90
4.5
2.3
5.4
104.4 950
25.6
18.6
0.73
31.5
1.73
14.8
100.5 850
25.0
17.5
0.70
30.6
1.65
15.2
6.0
3.4
7.7
100.8 950
25.7
18.8
0.73
31.5
1.69
15.2
120.7 850
23.2
16.6
0.72
30.1
2.01
11.5
3.0
1.4
3.2
121.2 950
23.8
17.8
0.75
30.8
2.05
11.6
113.7 850
23.5
16.7
0.71
29.9
1.89
12.4
100
4.5
2.3
5.2
114.1 950
24.1
17.9
0.74
30.7
1.93
12.5
110.3 850
23.6
16.8
0.71
29.9
1.84
12.8
6.0
3.3
7.5
110.5 950
24.2
18.1
0.75
30.6
1.88
12.9
130.1 850
21.7
15.9
0.73
29.3
2.22
9.8
3.0
1.4
3.2
130.6 950
22.3
17.1
0.77
30.0
2.27
9.8
123.4 850
22.0
16.0
0.73
29.2
2.10
10.5
4.5
2.2
5.1
110
123.7 950
22.5
17.2
0.76
29.8
2.14
10.5
120.0 850
22.0
16.2
0.74
29.0
2.04
10.8
6.0
3.2
7.3
120.2 950
22.6
17.4
0.77
29.7
2.08
10.9
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
XT Models, Rev.: A
51
Discharge Suction Subcooling Superheat
PSIG
PSIG
°F
°F
219.5
142.8
17.1
20.1
220.9
145.0
16.8
19.4
200.3
141.9
13.1
21.1
201.6
144.1
12.8
20.4
192.3
141.4
11.3
21.5
193.5
143.6
11.0
20.8
256.7
145.7
17.6
16.8
258.3
148.0
17.1
16.1
234.2
144.8
13.3
17.7
235.7
147.1
12.8
17.0
224.8
144.3
11.4
18.1
226.3
146.6
11.1
17.4
295.9
148.6
17.7
13.6
297.8
150.9
17.2
12.9
270.0
147.6
13.4
14.7
271.8
149.9
13.0
14.0
259.2
147.1
11.5
15.1
260.9
149.5
11.0
14.3
338.5
150.8
17.8
12.3
340.7
153.1
17.2
11.6
308.9
149.8
13.8
13.2
310.9
152.1
13.2
12.5
296.5
149.3
12.0
13.6
298.5
151.6
11.4
12.9
386.3
152.7
17.7
11.9
388.8
155.1
17.0
11.2
352.5
151.7
14.3
12.9
354.8
154.0
13.5
12.2
338.4
151.2
12.6
13.2
340.6
153.5
11.9
12.5
439.8
154.8
17.4
11.7
442.6
157.2
16.6
11.0
401.3
153.8
14.3
12.7
403.9
156.2
13.3
12.0
385.2
153.3
12.8
13.1
387.8
155.7
12.0
12.4
495.3
156.8
17.6
12.0
498.5
159.3
16.7
11.3
452.0
155.8
13.7
13.0
454.9
158.2
12.8
12.2
433.9
155.3
12.2
13.4
436.7
157.7
11.3
12.6
Enertech Global
Section 11: Engineering Data
Model 036 Part Load Heating Performance Data: 3.0 Ton
Heating
Flow
WPD LWT Airflow LAT
HC
HE
COP Discharge Suction
GPM PSI FT
°F
CFM
°F
MBtuh MBtuh kW W/W
PSIG
PSIG
20.8
950
87.7
18.2
12.2 1.76 3.04
299.0
74.9
25
6.0 2.0 4.7
20.6 1050
86.5
18.7
12.8 1.73 3.16
295.0
74.9
21.5
950
87.9
18.4
12.3 1.77 3.05
301.0
74.7
3.0 0.6 1.4
21.3 1050
86.4
18.6
12.7 1.73 3.14
294.0
74.5
23.8
950
89.0
19.5
13.5 1.77 3.23
306.0
79.5
30
4.5 1.2 2.8
23.8 1050
87.2
19.5
13.5 1.75 3.26
302.0
79.3
25.1
950
89.8
20.3
14.2 1.77 3.35
309.0
82.8
6.0 2.0 4.6
25.1 1050
87.9
20.3
14.3 1.75 3.40
304.0
82.7
29.4
950
90.9
21.5
15.4 1.78 3.53
315.0
87.9
3.0 0.6 1.3
29.4 1050
88.9
21.5
15.5 1.75 3.59
309.0
87.6
32.3
950
92.3
22.9
16.8 1.78 3.76
320.0
94.3
40
4.5 1.2 2.7
32.2 1050
90.2
22.9
16.9 1.75 3.84
313.0
94.0
34.0
950
93.0
23.6
17.6 1.76 3.92
319.0
98.5
6.0 1.9 4.4
33.9 1050
90.9
23.7
17.8 1.73 4.02
312.0
98.2
37.3
950
93.9
24.5
18.4 1.80 4.00
328.0
102.1
3.0 0.5 1.3
37.2 1050
91.7
24.6
18.6 1.76 4.09
321.0
101.7
40.8
950
95.4
26.1
20.0 1.79 4.28
332.0
110.1
50
4.5 1.1 2.6
40.7 1050
93.1
26.1
20.2 1.75 4.39
324.0
109.7
42.8
950
96.2
26.9
20.9 1.78 4.45
333.0
115.6
6.0 1.8 4.2
42.7 1050
93.9
27.0
21.1 1.73 4.58
324.0
115.2
45.2
950
97.0
27.7
21.5 1.82 4.46
344.0
117.7
3.0 0.5 1.2
45.1 1050
94.5
27.8
21.7 1.78 4.58
335.0
117.1
49.0
950
99.0
29.8
23.9 1.72 5.08
330.0
126.6
60
4.5 1.1 2.4
48.9 1050
96.4
29.9
24.2 1.67 5.24
320.0
126.1
51.4
950
100.1 30.9
25.1 1.71 5.31
331.0
133.2
6.0 1.7 4.0
51.3 1050
97.4
31.1
25.4 1.66 5.49
322.0
133.0
52.7
950
100.4 31.2
25.2 1.76 5.20
341.0
133.0
3.0 0.5 1.2
52.5 1050
97.6
31.3
25.5 1.71 5.37
331.0
132.2
57.4
950
102.5 33.3
27.4 1.74 5.61
345.0
145.3
70
4.5 1.0 2.4
57.3 1050
99.5
33.5
27.7 1.69 5.81
334.0
144.5
60.2
950
103.6 34.5
28.6 1.74 5.81
350.0
153.6
6.0 1.7 3.9
60.0 1050 100.6 34.7
29.0 1.68 6.05
338.0
152.9
60.5
950
103.6 34.4
28.4 1.78 5.67
356.0
150.5
3.0 0.5 1.1
60.2 1050 100.5 34.6
28.7 1.72 5.89
344.0
149.6
65.9
950
105.9 36.8
30.8 1.77 6.11
362.0
164.9
80
4.5 1.0 2.3
65.7 1050 102.7 37.0
31.2 1.71 6.36
349.0
164.0
68.9
950
107.3 38.2
32.2 1.76 6.37
366.0
175.5
6.0 1.6 3.8
68.7 1050 104.0 38.5
32.7 1.69 6.66
353.0
174.6
68.3
950
106.8 37.7
31.6 1.81 6.13
371.0
169.2
3.0 0.5 1.1
68.0 1050 103.5 38.0
32.0 1.74 6.39
358.0
168.0
74.4
950
109.2 40.2
34.1 1.80 6.56
378.0
185.4
4.5 1.0 2.3
90
74.1 1050 105.8 40.6
34.7 1.73 6.89
364.0
184.4
77.7
950
110.8 41.9
35.8 1.79 6.86
383.0
198.1
6.0 1.6 3.7
77.5 1050 107.2 42.2
36.4 1.72 7.22
368.0
197.0
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
EWT
°F
Enertech Global
52
Subcooling
°F
20.4
20.5
21.5
20.4
21.6
21.6
21.5
21.4
21.6
21.5
20.6
20.5
17.5
17.5
20.5
20.5
17.5
17.6
14.5
14.4
19.6
19.6
16.6
16.5
13.5
13.6
19.6
19.5
15.4
15.5
13.7
13.5
18.6
18.5
14.7
14.6
11.7
11.6
17.6
17.5
13.7
13.6
10.6
10.5
Superheat
°F
7.3
7.4
7.9
7.8
7.1
7.0
5.9
5.8
6.1
6.2
5.3
5.4
4.2
4.3
5.0
5.0
4.8
4.9
3.9
3.9
4.1
4.1
4.4
4.5
3.9
3.8
3.7
3.8
4.9
5.0
4.1
4.2
4.2
4.3
6.1
6.1
5.4
5.4
5.2
5.3
7.6
7.6
6.9
7.0
XT Models, Rev.: A
Section 11: Engineering Data
Model 036 Full Load Heating Performance Data: 3.0 Ton
Heating
LWT Aiflow LAT
HC
HE
COP
Discharge Suction Subcooling Superheat
PSI
FT
°F
CFM
°F
MBtuh MBtuh kW
W/W
PSIG
PSIG
°F
°F
20.6
1200
90.7
26.8
19.2
2.24
3.51
295.3
66.3
23.1
8.3
25
9.0
4.1
9.4
20.5
1350
88.6
27.1
19.5
2.24
3.55
295.3
66.1
23.1
8.4
20.3
1200
92.4
29.0
21.2
2.29
3.71
304.6
68.8
28.2
7.9
4.5
1.4
3.2
20.1
1350
90.1
29.3
21.5
2.29
3.75
304.6
68.7
28.2
8.0
23.3
1200
93.5
30.5
22.6
2.31
3.87
308.2
74.9
25.7
6.7
30
7.0
2.8
6.6
23.3
1350
91.1
30.8
22.9
2.31
3.91
308.2
74.8
25.7
6.7
24.8
1200
93.5
30.5
22.7
2.30
3.89
307.4
77.4
23.5
5.6
9.0
4.0
9.1
24.8
1350
91.1
30.7
22.9
2.30
3.91
307.4
77.3
23.5
5.7
28.7
1200
95.2
32.6
24.6
2.34
4.08
314.9
83.7
25.0
6.3
4.5
1.3
2.9
28.6
1350
92.6
32.9
24.9
2.34
4.12
314.9
83.5
25.0
6.4
32.3
1200
96.5
34.3
26.2
2.36
4.26
318.7
91.1
22.2
5.7
40
7.0
2.6
6.0
32.2
1350
93.7
34.6
26.5
2.36
4.30
318.7
90.9
22.2
5.8
34.0
1200
96.5
34.3
26.3
2.34
4.30
317.8
94.2
19.8
4.7
9.0
3.6
8.3
33.9
1350
93.7
34.5
26.5
2.34
4.32
317.8
94.0
19.8
4.8
37.1
1200
98.1
36.4
28.2
2.40
4.44
326.5
99.0
22.2
5.7
4.5
1.2
2.7
36.9
1350
95.2
36.7
28.5
2.40
4.48
326.5
98.8
22.2
5.8
41.2
1200
99.5
38.2
29.9
2.42
4.63
330.4
107.9
19.1
5.7
50
7.0
2.4
5.5
41.1
1350
96.4
38.5
30.2
2.42
4.66
330.4
107.6
19.1
5.8
43.1
1200
99.5
38.2
30.0
2.40
4.66
329.5
111.5
16.5
4.9
9.0
3.3
7.6
43.1
1350
96.4
38.5
30.3
2.40
4.70
329.5
111.2
16.5
5.0
44.9
1200 102.0
41.5
33.0
2.50
4.86
345.7
117.2
21.3
5.1
4.5
1.1
2.5
44.7
1350
98.7
41.9
33.4
2.50
4.91
345.7
116.9
21.3
5.2
49.7
1200 103.6
43.6
35.0
2.52
5.07
349.9
127.6
18.0
5.8
60
7.0
2.2
5.0
49.6
1350 100.2
44.0
35.4
2.52
5.12
349.9
127.3
18.0
6.0
52.0
1200 103.6
43.6
35.0
2.51
5.09
348.9
131.8
15.2
5.2
9.0
3.0
7.0
51.9
1350 100.1
43.9
35.3
2.51
5.13
348.9
131.5
15.2
5.3
52.6
1200 106.2
46.9
37.9
2.64
5.21
368.3
136.4
21.1
5.2
4.5
1.0
2.3
52.5
1350 102.4
47.3
38.3
2.64
5.25
368.3
136.1
21.1
5.3
58.1
1200 108.1
49.4
40.3
2.66
5.44
372.6
148.6
17.5
6.6
70
7.0
2.0
4.7
58.0
1350 104.2
49.8
40.7
2.66
5.49
372.6
148.2
17.5
6.8
60.8
1200 108.0
49.3
40.3
2.65
5.45
371.6
153.5
14.7
6.0
9.0
2.8
6.5
60.7
1350 104.1
49.7
40.7
2.65
5.50
371.6
153.2
14.7
6.1
60.8
1200 109.7
51.4
41.9
2.78
5.42
388.7
154.9
20.0
6.2
4.5
0.9
2.1
60.6
1350 105.5
51.8
42.3
2.78
5.46
388.7
154.6
20.0
6.3
66.9
1200 111.7
54.0
44.4
2.80
5.65
393.3
168.7
16.2
8.2
80
7.0
1.9
4.4
66.8
1350 107.4
54.5
44.9
2.80
5.70
393.3
168.3
16.2
8.4
69.8
1200 111.6
53.9
44.4
2.78
5.68
392.2
174.3
13.2
7.6
9.0
2.6
6.1
69.7
1350 107.3
54.4
44.9
2.78
5.73
392.2
173.9
13.2
7.8
69.0
1200 113.1
55.9
45.9
2.92
5.61
410.5
173.9
19.1
7.5
4.5
0.9
2.0
68.7
1350 108.7
56.4
46.4
2.92
5.66
410.5
173.5
19.1
7.6
75.6
1200 115.4
58.8
48.8
2.94
5.86
415.3
189.4
15.1
10.1
7.0
1.8
4.1
90
75.5
1350 110.7
59.3
49.3
2.94
5.91
415.3
188.9
15.1
10.2
78.8
1200 115.3
58.7
48.7
2.93
5.87
414.2
195.7
12.0
9.5
9.0
2.4
5.6
78.7
1350 110.6
59.2
49.2
2.93
5.92
414.2
195.2
12.0
9.7
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
EWT
°F
Flow
GPM
WPD
XT Models, Rev.: A
53
Enertech Global
Section 11: Engineering Data
Model 036 Part Load Cooling Performance Data: 3.0 Ton
Cooling
LWT Airflow
TC
SC
HR
EER
Discharge Suction Subcooling Superheat
°F
CFM MBtuh MBtuh S/T MBtuh kW Btuh/W
PSIG
PSIG
°F
°F
74.2
950
30.7
21.3 0.69 35.3 1.33
23.0
245.0
137.7
24.4
10.1
3.0 0.4 1.0
74.6
1050
31.2
22.4 0.72 35.7 1.33
23.4
247.0
139.9
24.5
10.8
66.3
950
31.5
21.6 0.68 35.7 1.21
26.0
214.0
136.3
19.5
10.6
50
4.5 0.9 2.1
66.6
1050
32.1
22.7 0.71 36.2 1.21
26.4
216.0
138.5
20.5
11.1
62.4
950
32.0
21.8 0.68 36.0 1.17
27.4
200.0
135.5
18.3
10.8
6.0 1.5 3.4
62.5
1050
32.5
22.9 0.70 36.5 1.16
28.0
201.0
137.7
18.3
11.3
83.7
950
29.4
20.9 0.71 34.4 1.49
19.8
281.0
140.3
24.4
8.5
3.0 0.4 1.0
84.0
1050
29.8
22.0 0.74 34.9 1.49
20.1
283.0
142.5
24.5
8.8
75.9
950
30.1
21.2 0.70 34.7 1.34
22.5
247.0
138.9
19.3
8.9
60
4.5 0.9 2.0
76.1
1050
30.6
22.3 0.73 35.2 1.34
22.9
249.0
141.0
19.5
9.4
72.0
950
30.6
21.3 0.70 34.9 1.28
23.9
232.0
138.2
17.4
9.0
6.0 1.4 3.3
72.2
1050
31.1
22.5 0.72 35.5 1.28
24.3
234.0
140.3
18.4
9.4
93.1
950
27.9
20.4 0.73 33.5 1.66
16.8
319.0
142.9
23.5
6.8
3.0 0.4 0.9
93.4
1050
28.3
21.5 0.76 34.0 1.67
17.0
322.0
144.8
24.4
7.3
85.5
950
28.7
20.7 0.72 33.8 1.50
19.1
285.0
141.5
19.5
7.3
70
4.5 0.8 1.9
85.7
1050
29.1
21.8 0.75 34.3 1.50
19.5
286.0
143.6
19.5
7.8
81.7
950
29.1
20.8 0.71 34.0 1.43
20.4
269.0
140.9
17.6
7.3
6.0 1.4 3.2
81.8
1050
29.6
21.9 0.74 34.4 1.42
20.8
269.0
143.0
17.4
7.8
102.6
950
26.5
19.9 0.75 32.8 1.87
14.2
363.0
145.5
23.7
6.1
3.0 0.4 0.9
102.8 1050
26.9
21.0 0.78 33.2 1.87
14.4
364.0
147.4
23.6
6.6
95.1
950
27.2
20.1 0.74 33.0 1.69
16.1
327.0
144.1
19.7
6.7
80
4.5 0.8 1.9
95.3
1050
27.6
21.2 0.77 33.4 1.69
16.4
328.0
146.1
19.6
7.0
91.4
950
27.6
20.3 0.73 33.1 1.61
17.2
309.0
143.5
17.4
6.6
6.0 1.4 3.2
91.5
1050
28.0
21.3 0.76 33.5 1.61
17.4
310.0
145.5
17.4
7.0
112.0
950
24.9
19.4 0.78 32.1 2.09
11.9
408.0
147.8
22.7
6.2
3.0 0.4 0.9
112.3 1050
25.3
20.4 0.81 32.5 2.10
12.1
410.0
149.9
22.8
6.5
104.7
950
25.7
19.6 0.77 32.1 1.90
13.5
370.0
146.7
18.5
6.7
90
4.5 0.8 1.9
104.9 1050
26.0
20.8 0.80 32.5 1.90
13.7
371.0
148.4
18.6
7.2
101.1
950
26.1
19.7 0.76 32.3 1.82
14.3
354.0
146.0
17.5
6.7
6.0 1.4 3.2
101.2 1050
26.4
20.9 0.79 32.6 1.82
14.5
355.0
147.7
17.6
7.3
121.6
950
23.4
18.7 0.80 31.4 2.35
10.0
457.0
150.5
21.7
6.4
3.0 0.4 1.0
121.9 1050
23.7
19.9 0.84 31.8 2.36
10.1
461.0
151.9
22.7
7.1
114.4
950
24.1
19.0 0.79 31.4 2.14
11.2
418.0
149.4
17.7
6.9
100
4.5 0.8 1.9
114.5 1050
24.4
20.1 0.82 31.7 2.14
11.4
419.0
151.1
17.7
7.5
110.8
950
24.4
19.2 0.79 31.5 2.06
11.9
401.0
148.5
16.5
7.3
6.0 1.4 3.2
110.9 1050
24.8
20.2 0.81 31.8 2.06
12.0
403.0
150.5
16.7
7.4
131.3
950
21.9
18.2 0.83 31.0 2.66
8.2
516.0
152.9
22.7
7.0
3.0 0.4 1.0
131.5 1050
22.2
19.5 0.88 31.2 2.66
8.3
516.0
153.9
22.7
7.9
124.1
950
22.5
18.3 0.82 30.7 2.41
9.3
470.0
152.0
16.7
7.5
4.5 0.8 2.0
110
124.2 1050
22.8
19.5 0.85 31.1 2.43
9.4
474.0
153.5
17.7
8.1
120.6
950
22.8
18.4 0.81 30.7 2.33
9.8
453.0
151.4
15.6
7.6
6.0 1.4 3.2
120.7 1050
23.1
19.6 0.85 31.1 2.32
9.9
454.0
153.0
15.7
8.2
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
EWT
°F
Flow WPD
GPM PSI FT
Enertech Global
54
XT Models, Rev.: A
Section 11: Engineering Data
Model 036 Full Load Cooling Performance Data: 3.0 Ton
Cooling
LWT Aiflow TC
SC
HR
EER
PSI
FT
°F
CFM MBtuh MBtuh S/T MBtuh kW
Btuh/W
72.5 1250 42.4
28.5
0.67
49.1
1.95
21.7
4.5
1.1
2.6
72.9 1350 43.1
29.8
0.69
49.9
2.00
21.6
64.5 1250 42.9
28.8
0.67
49.1
1.83
23.4
50
7.0
2.1
4.8
64.7 1350 43.5
30.1
0.69
49.9
1.88
23.1
61.2 1250 43.0
28.9
0.67
49.1
1.79
24.0
9.0
3.1
7.0
61.4 1350 43.7
30.2
0.69
49.9
1.83
23.9
82.0 1250 40.8
27.9
0.68
48.1
2.13
19.2
4.5
1.0
2.4
82.4 1350 41.5
29.1
0.70
48.9
2.18
19.0
74.2 1250 41.3
28.2
0.68
48.1
1.99
20.8
60
7.0
2.0
4.5
74.4 1350 41.9
29.4
0.70
48.9
2.04
20.5
71.0 1250 41.4
28.2
0.68
48.1
1.95
21.2
9.0
2.9
6.6
71.2 1350 42.0
29.5
0.70
48.8
2.00
21.0
91.5 1250 39.1
27.2
0.70
47.0
2.32
16.9
4.5
1.0
2.3
91.9 1350 39.7
28.4
0.72
47.8
2.38
16.7
83.8 1250 39.6
27.5
0.69
47.0
2.17
18.2
70
7.0
1.8
4.2
84.1 1350 40.2
28.7
0.71
47.8
2.23
18.0
80.7 1250 39.7
27.5
0.69
46.9
2.12
18.7
9.0
2.7
6.2
80.9 1350 40.3
28.8
0.71
47.7
2.18
18.5
101.1 1250 37.3
26.3
0.71
46.0
2.54
14.7
4.5
0.9
2.2
101.4 1350 37.9
27.5
0.73
46.8
2.61
14.5
93.5 1250 37.7
26.6
0.71
45.8
2.38
15.8
80
7.0
1.7
4.0
93.7 1350 38.3
27.7
0.72
46.6
2.44
15.7
90.5 1250 37.8
26.7
0.71
45.7
2.32
16.3
9.0
2.6
5.9
90.7 1350 38.4
27.8
0.72
46.5
2.38
16.1
110.6 1250 35.3
25.3
0.72
44.9
2.81
12.6
4.5
0.9
2.1
110.9 1350 35.8
26.4
0.74
45.6
2.88
12.4
103.2 1250 35.7
25.5
0.71
44.7
2.63
13.6
90
7.0
1.7
3.8
103.4 1350 36.2
26.7
0.74
45.4
2.70
13.4
100.2 1250 35.8
25.6
0.72
44.6
2.57
13.9
9.0
2.4
5.7
100.4 1350 36.3
26.7
0.74
45.3
2.63
13.8
120.1 1250 33.1
24.2
0.73
43.8
3.14
10.5
4.5
0.8
1.9
120.4 1350 33.6
25.3
0.75
44.6
3.22
10.4
112.8 1250 33.4
24.5
0.73
43.4
2.94
11.4
100
7.0
1.6
3.6
113.0 1350 33.9
25.5
0.75
44.2
3.02
11.2
109.9 1250 33.5
24.5
0.73
43.3
2.87
11.7
9.0
2.3
5.3
110.1 1350 34.0
25.6
0.75
44.0
2.94
11.6
129.6 1250 30.8
23.1
0.75
42.7
3.49
8.8
4.5
0.8
1.8
129.9 1350 31.2
24.1
0.77
43.4
3.58
8.7
122.5 1250 31.1
23.3
0.75
42.3
3.27
9.5
7.0
1.5
3.3
110
122.7 1350 31.6
24.3
0.77
43.0
3.35
9.4
119.6 1250 31.2
23.4
0.75
42.1
3.19
9.8
9.0
2.1
4.9
119.8 1350 31.7
24.4
0.77
42.9
3.27
9.7
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
EWT
°F
Flow
GPM
WPD
XT Models, Rev.: A
55
Discharge Suction Subcooling Superheat
PSIG
PSIG
°F
°F
243.9
135.5
27.1
12.2
244.7
137.2
27.4
12.9
222.7
134.8
22.1
13.0
223.4
136.6
22.3
13.6
215.0
134.6
20.3
13.1
215.7
136.4
20.5
13.8
281.0
137.5
27.0
10.1
281.9
139.3
27.3
10.6
256.6
136.9
21.8
10.8
257.3
138.7
22.0
11.3
247.7
136.7
19.9
11.0
248.5
138.5
20.1
11.5
320.5
139.6
26.5
8.1
321.5
141.4
26.8
8.6
292.6
139.0
21.4
8.8
293.5
140.8
21.6
9.4
282.6
138.7
19.4
9.0
283.4
140.5
19.6
9.6
364.8
141.3
25.9
7.2
365.9
143.1
26.1
7.7
333.0
140.6
21.2
7.9
334.0
142.5
21.4
8.4
321.6
140.4
19.3
8.0
322.5
142.2
19.5
8.5
415.1
142.9
25.1
6.9
416.4
144.8
25.3
7.4
378.9
142.3
20.7
7.6
380.1
144.1
20.8
8.2
365.9
142.0
18.9
7.8
367.0
143.8
19.1
8.4
471.0
145.0
24.3
7.1
472.4
146.9
24.5
7.6
430.0
144.3
19.6
7.9
431.3
146.2
19.8
8.4
415.2
144.1
17.9
7.9
416.5
145.9
18.1
8.5
529.3
147.1
24.5
7.6
531.0
149.0
24.8
8.1
483.2
146.4
18.6
8.3
484.7
148.3
18.9
8.9
466.6
146.1
16.7
8.4
468.1
148.0
16.9
9.1
Enertech Global
Section 11: Engineering Data
Model 048 Part Load Heating Performance Data: 4.0 Ton
Heating
Flow
WPD LWT Airflow LAT
HC
HE
COP Discharge Suction
GPM PSI FT
°F
CFM
°F
MBtuh MBtuh kW W/W
PSIG
PSIG
20.5 1300
88.1
25.5
17.4 2.35 3.18
286.0
79.2
25
8.0 2.8 6.5
20.4 1450
86.3
25.6
17.7 2.31 3.25
279.0
78.8
21.1 1300
88.0
25.3
17.2 2.37 3.12
288.0
78.3
4.0 0.8 1.9
21.0 1450
86.2
25.4
17.4 2.34 3.19
283.0
77.9
23.7 1300
88.9
26.6
18.4 2.38 3.27
292.0
82.3
30
6.0 1.7 3.8
23.6 1450
87.0
26.7
18.7 2.34 3.34
287.0
81.9
25.1 1300
89.3
27.2
19.1 2.37 3.36
292.0
84.6
8.0 2.7 6.3
25.0 1450
87.4
27.3
19.4 2.33 3.44
286.0
84.2
29.6 1300
90.2
28.3
20.1 2.41 3.45
299.0
88.2
4.0 0.8 1.8
29.4 1450
88.2
28.6
20.5 2.36 3.54
293.0
87.7
32.2 1300
91.7
30.5
22.6 2.30 3.89
285.0
91.7
40
6.0 1.6 3.7
32.1 1450
89.5
30.6
22.9 2.25 3.99
278.0
91.1
34.0 1300
92.2
31.2
23.4 2.28 4.02
284.0
94.7
8.0 2.6 6.0
33.9 1450
90.1
31.4
23.8 2.23 4.12
278.0
94.1
37.4 1300
93.0
32.2
24.4 2.31 4.09
290.0
96.9
4.0 0.8 1.7
37.3 1450
90.6
32.3
24.5 2.26 4.18
283.0
96.3
41.0 1300
94.3
34.1
26.2 2.32 4.32
295.0
103.2
50
6.0 1.5 3.5
40.9 1450
91.9
34.3
26.6 2.27 4.44
288.0
102.5
43.0 1300
95.1
35.2
27.3 2.31 4.47
296.0
106.9
8.0 2.5 5.7
42.9 1450
92.6
35.4
27.7 2.25 4.61
288.0
106.3
45.6 1300
95.5
35.9
27.9 2.34 4.49
302.0
108.1
4.0 0.7 1.7
45.4 1450
93.0
36.0
28.2 2.29 4.62
294.0
107.3
49.6 1300
97.3
38.3
30.2 2.35 4.77
309.0
115.6
60
6.0 1.5 3.3
49.5 1450
94.6
38.5
30.7 2.29 4.92
300.0
114.8
51.9 1300
98.1
39.5
31.5 2.34 4.94
311.0
120.4
8.0 2.4 5.5
51.8 1450
95.4
39.8
32.0 2.28 5.10
301.0
119.6
53.7 1300
98.4
39.8
31.7 2.39 4.89
316.0
120.1
4.0 0.7 1.6
53.4 1450
95.6
40.0
32.1 2.32 5.05
307.0
119.1
58.2 1300 100.4 42.7
34.5 2.40 5.21
324.0
129.1
70
6.0 1.4 3.2
58.0 1450
97.4
43.0
35.0 2.33 5.40
314.0
128.2
60.8 1300 101.2 43.8
35.7 2.39 5.39
326.0
134.9
8.0 2.3 5.3
60.6 1450
98.2
44.2
36.3 2.32 5.59
315.0
134.0
61.7 1300 101.2 43.9
35.6 2.43 5.29
331.0
132.8
4.0 0.7 1.6
61.4 1450
98.2
44.1
36.1 2.36 5.48
320.0
131.6
66.7 1300 103.6 47.2
38.8 2.45 5.64
341.0
143.7
80
6.0 1.4 3.1
66.4 1450 100.4 47.7
39.6 2.37 5.89
329.0
142.5
69.6 1300 104.7 48.7
40.4 2.44 5.86
343.0
150.7
8.0 2.2 5.2
69.4 1450 101.4 49.1
41.1 2.36 6.11
331.0
149.6
69.5 1300 104.3 48.2
39.7 2.48 5.69
348.0
146.6
4.0 0.7 1.5
69.2 1450 101.0 48.5
40.3 2.40 5.92
335.0
145.1
75.1 1300 107.0 51.9
43.3 2.51 6.07
359.0
159.1
6.0 1.3 3.1
90
74.9 1450 103.4 52.3
44.1 2.42 6.34
345.0
157.7
78.3 1300 108.3 53.8
45.3 2.49 6.33
362.0
167.7
8.0 2.2 5.1
78.1 1450 104.7 54.4
46.2 2.40 6.63
348.0
166.4
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
EWT
°F
Enertech Global
56
Subcooling
°F
12.6
11.6
15.5
15.5
14.5
14.7
11.6
11.6
13.5
13.7
12.5
11.6
8.5
8.6
11.5
11.5
9.5
9.7
6.5
6.5
10.5
10.6
8.7
8.7
5.7
5.5
10.5
10.7
8.6
8.7
4.6
4.6
10.6
10.6
8.6
8.7
4.6
4.6
10.7
10.6
8.7
8.6
4.7
4.6
Superheat
°F
7.7
7.6
7.9
7.9
7.3
7.3
6.8
6.7
6.7
6.7
6.6
6.7
6.4
6.6
6.6
6.6
7.3
7.3
7.5
7.5
7.0
7.0
8.6
8.5
9.0
9.0
7.8
7.8
10.1
10.0
10.7
10.7
9.1
9.2
11.9
12.0
12.8
12.7
10.5
10.6
14.0
14.0
15.2
15.2
XT Models, Rev.: A
Section 11: Engineering Data
Model 048 Full Load Heating Performance Data: 4.0 Ton
Heating
LWT Aiflow LAT
HC
HE
COP
Discharge Suction Subcooling Superheat
PSI
FT
°F
CFM
°F
MBtuh MBtuh kW
W/W
PSIG
PSIG
°F
°F
20.4
1500
92.8
37.0
26.6
3.06
3.54
295.2
66.6
13.4
7.7
25
12.0
5.7
13.1
20.2
1700
90.8
38.1
27.7
3.05
3.66
294.2
66.5
13.2
7.7
21.1
1500
92.3
36.2
25.8
3.04
3.49
292.7
67.9
17.2
7.9
6.0
1.8
4.2
20.7
1700
90.3
37.3
27.0
3.03
3.61
291.8
67.8
17.0
8.0
23.8
1500
93.2
37.6
27.1
3.07
3.59
297.8
72.4
15.9
7.4
30
9.0
3.5
8.2
23.5
1700
91.1
38.8
28.3
3.07
3.70
296.9
72.2
15.7
7.4
25.2
1500
93.7
38.4
27.9
3.09
3.64
300.1
74.8
12.7
7.0
12.0
5.5
12.7
25.0
1700
91.6
39.6
29.1
3.08
3.77
299.2
74.7
12.5
7.0
29.6
1500
95.3
41.0
30.3
3.15
3.81
309.2
82.2
15.0
7.1
6.0
1.7
4.0
29.1
1700
93.0
42.3
31.6
3.15
3.94
308.2
82.1
14.8
7.2
32.7
1500
96.3
42.6
31.7
3.19
3.91
314.5
87.6
13.3
7.3
40
9.0
3.4
7.8
32.4
1700
93.9
43.9
33.0
3.18
4.05
313.5
87.4
13.1
7.4
34.4
1500
96.9
43.5
32.6
3.20
3.98
317.0
90.6
9.9
7.2
12.0
5.3
12.2
34.2
1700
94.5
44.9
34.0
3.20
4.11
316.0
90.4
9.7
7.3
38.1
1500
98.3
45.9
34.7
3.27
4.11
325.6
96.7
12.8
7.4
6.0
1.7
3.8
37.6
1700
95.8
47.3
36.2
3.26
4.25
324.6
96.5
12.6
7.4
41.7
1500
99.4
47.6
36.3
3.31
4.21
331.2
103.0
11.0
8.5
50
9.0
3.2
7.5
41.3
1700
96.7
49.1
37.8
3.30
4.36
330.2
102.8
10.8
8.5
43.6
1500 100.0 48.6
37.3
3.32
4.29
333.8
106.5
7.2
8.6
12.0
5.1
11.7
43.3
1700
97.3
50.1
38.8
3.32
4.42
332.8
106.4
7.0
8.7
46.8
1500 100.7 49.8
38.3
3.38
4.32
339.5
111.8
11.7
8.2
6.0
1.6
3.6
46.3
1700
98.0
51.4
39.9
3.37
4.47
338.5
111.7
11.6
8.2
50.8
1500 102.0 51.8
40.1
3.42
4.44
345.4
119.1
9.8
10.0
60
9.0
3.0
7.0
50.4
1700
99.1
53.4
41.8
3.41
4.59
344.4
118.9
9.6
10.0
52.9
1500 102.6 52.8
41.1
3.43
4.51
348.1
123.2
5.9
10.6
12.0
4.7
11.0
52.6
1700
99.7
54.5
42.8
3.43
4.66
347.0
123.0
5.7
10.6
55.6
1500 103.2 53.8
41.9
3.50
4.50
353.5
127.5
11.7
9.4
6.0
1.4
3.3
55.0
1700 100.2 55.5
43.6
3.49
4.66
352.4
127.3
11.4
9.4
60.0
1500 104.5 55.9
43.8
3.54
4.63
359.6
135.8
9.5
11.9
70
9.0
2.8
6.5
59.6
1700 101.4 57.6
45.6
3.53
4.78
358.5
135.6
9.4
11.9
62.3
1500 105.2 57.0
44.9
3.55
4.71
362.4
140.5
5.5
12.8
12.0
4.4
10.2
62.0
1700 102.0 58.8
46.7
3.55
4.85
361.3
140.3
5.4
12.7
64.2
1500 106.2 58.6
46.1
3.65
4.71
369.9
143.4
11.7
11.0
6.0
1.3
3.1
63.5
1700 102.9 60.4
48.0
3.64
4.86
368.8
143.2
11.5
11.0
69.0
1500 107.5 60.8
48.2
3.69
4.83
376.3
152.8
9.4
14.1
80
9.0
2.6
6.0
68.5
1700 104.2 62.7
50.1
3.68
4.99
375.2
152.5
9.3
14.1
71.5
1500 108.3 62.1
49.4
3.71
4.91
379.3
158.0
5.3
15.3
12.0
4.1
9.4
71.2
1700 104.9 64.0
51.4
3.70
5.07
378.1
157.8
5.1
15.3
72.7
1500 109.1 63.3
50.3
3.80
4.88
386.3
159.5
11.9
12.8
6.0
1.2
2.8
72.0
1700 105.6 65.3
52.4
3.79
5.05
385.1
159.2
11.8
12.9
77.9
1500 110.6 65.8
52.7
3.85
5.01
393.1
169.9
9.7
16.6
9.0
2.4
5.5
90
77.5
1700 106.9 67.8
54.7
3.84
5.17
391.8
169.6
9.5
16.6
80.7
1500 111.4 67.1
53.9
3.87
5.08
396.1
175.8
5.3
18.0
12.0
3.7
8.5
80.4
1700 107.7 69.2
56.0
3.86
5.25
394.9
175.5
5.1
18.0
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
EWT
°F
Flow
GPM
WPD
XT Models, Rev.: A
57
Enertech Global
Section 11: Engineering Data
Model 048 Part Load Cooling Performance Data: 4.0 Ton
Cooling
LWT Aiflow
TC
SC
HR
EER
Discharge Suction Subcooling Superheat
°F
CFM MBtuh MBtuh S/T MBtuh kW Btuh/W
PSIG
PSIG
°F
°F
74.6 1300
41.2
28.4 0.69 47.7 1.89
21.8
247.0
139.8
17.5
10.9
4.0 0.7 1.6
74.9 1450
41.9
29.9 0.71 48.3 1.89
22.2
249.0
142.3
17.5
10.9
66.7 1300
42.8
29.0 0.68 48.6 1.69
25.3
216.0
137.7
14.4
11.3
50
6.0 1.4 3.3
66.9 1450
43.5
30.5 0.70 49.3 1.69
25.7
217.0
140.1
14.3
11.6
62.7 1300
43.7
29.3 0.67 49.1 1.60
27.3
201.0
136.4
13.5
12.1
8.0 2.4 5.5
62.9 1450
44.4
30.9 0.69 49.9 1.60
27.8
202.0
138.9
13.4
12.4
83.8 1300
39.0
27.6 0.71 46.1 2.09
18.6
280.0
142.8
15.6
10.1
4.0 0.7 1.6
84.1 1450
39.6
29.1 0.73 46.8 2.10
18.9
282.0
145.3
15.5
10.2
76.2 1300
40.6
28.2 0.69 47.1 1.89
21.5
248.0
140.7
13.5
10.4
60
6.0 1.4 3.2
76.4 1450
41.3
29.7 0.72 47.7 1.89
21.8
249.0
143.1
13.4
10.6
72.3 1300
41.5
28.5 0.69 47.6 1.79
23.2
232.0
139.5
12.4
11.2
8.0 2.3 5.3
72.4 1450
42.1
30.0 0.71 48.2 1.78
23.6
232.0
142.0
11.3
11.4
93.0 1300
36.8
26.8 0.73 44.7 2.33
15.8
316.0
145.8
14.5
9.3
4.0 0.7 1.5
93.3 1450
37.3
28.4 0.76 45.3 2.33
16.0
318.0
147.9
14.5
9.5
85.6 1300
38.3
27.3 0.71 45.5 2.11
18.2
283.0
143.9
11.5
9.6
70
6.0 1.4 3.1
85.8 1450
38.9
28.8 0.74 46.1 2.11
18.4
284.0
146.1
11.5
9.8
81.8 1300
39.1
27.6 0.70 45.9 2.00
19.5
266.0
142.7
10.5
10.3
8.0 2.2 5.2
82.0 1450
39.8
29.1 0.73 46.6 2.00
19.9
267.0
145.0
10.5
10.6
102.4 1300
34.6
26.0 0.75 43.4 2.59
13.4
356.0
148.9
13.6
8.6
4.0 0.7 1.5
102.6 1450
35.1
27.5 0.78 43.9 2.59
13.5
358.0
151.0
13.6
8.8
95.2 1300
36.0
26.5 0.73 44.1 2.36
15.3
322.0
146.9
11.6
9.1
80
6.0 1.3 3.1
95.3 1450
36.6
28.0 0.77 44.6 2.36
15.5
323.0
148.9
11.5
9.4
91.5 1300
36.8
26.8 0.73 44.5 2.25
16.4
305.0
145.7
10.6
9.9
8.0 2.2 5.1
91.6 1450
37.4
28.3 0.76 45.1 2.25
16.6
306.0
147.8
10.5
10.2
111.7 1300
32.3
25.1 0.78 42.1 2.88
11.2
399.0
151.9
12.7
8.3
4.0 0.7 1.5
111.9 1450
32.7
26.8 0.82 42.5 2.88
11.4
400.0
153.6
12.6
8.7
104.7 1300
33.8
25.6 0.76 42.9 2.65
12.8
365.0
150.0
11.5
8.8
90
6.0 1.3 3.1
104.8 1450
34.2
27.2 0.80 43.2 2.64
12.9
365.0
151.9
10.5
9.3
101.1 1300
34.6
25.9 0.75 43.2 2.53
13.7
347.0
148.7
10.5
9.6
8.0 2.2 5.1
101.3 1450
35.0
27.5 0.78 43.7 2.53
13.9
348.0
150.6
10.5
10.0
121.2 1300
30.1
24.2 0.81 41.0 3.20
9.4
446.0
154.8
12.7
8.6
4.0 0.7 1.5
121.3 1450
30.3
25.9 0.85 41.2 3.20
9.5
446.0
156.4
11.7
9.0
114.3 1300
31.4
24.7 0.79 41.5 2.96
10.6
411.0
153.0
10.7
9.1
100
6.0 1.3 3.1
114.4 1450
31.9
26.2 0.82 42.0 2.96
10.8
412.0
154.9
10.6
9.3
110.8 1300
32.1
25.0 0.78 41.7 2.83
11.3
393.0
151.7
9.7
9.9
8.0 2.2 5.1
110.9 1450
32.6
26.4 0.81 42.3 2.83
11.5
394.0
153.7
9.7
10.1
130.7 1300
27.9
23.4 0.84 40.1 3.57
7.8
497.0
157.6
12.7
9.1
4.0 0.7 1.6
130.8 1450
28.1
25.0 0.89 40.3 3.56
7.9
497.0
159.2
11.7
9.4
123.8 1300
29.0
23.8 0.82 40.3 3.31
8.8
461.0
156.2
9.7
9.5
6.0 1.4 3.1
110
124.0 1450
29.4
25.3 0.86 40.6 3.31
8.9
462.0
157.8
9.7
9.8
120.5 1300
29.7
24.0 0.81 40.6 3.18
9.3
443.0
154.9
9.7
10.3
8.0 2.2 5.2
120.5 1450
30.0
25.5 0.85 40.9 3.17
9.5
443.0
156.7
8.7
10.5
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
EWT
°F
Flow WPD
GPM PSI FT
Enertech Global
58
XT Models, Rev.: A
Section 11: Engineering Data
Model 048 Full Load Cooling Performance Data: 4.0 Ton
Cooling
LWT Aiflow TC
SC
HR
EER
PSI
FT
°F
CFM MBtuh MBtuh S/T MBtuh kW
Btuh/W
71.8 1600 54.4
37.0
0.68
63.3
2.60
20.9
6.0
1.7
4.0
72.0 1750 54.7
38.2
0.70
63.9
2.71
20.2
64.6 1600 55.5
37.3
0.67
63.9
2.46
22.6
50
9.0
3.4
7.8
64.8 1750 55.8
38.5
0.69
64.6
2.57
21.7
61.0 1600 55.9
37.6
0.67
64.1
2.41
23.2
12.0
4.7
10.7
61.1 1750 56.2
38.8
0.69
64.8
2.52
22.3
81.3 1600 52.2
36.2
0.69
61.9
2.83
18.4
6.0
1.7
3.9
81.5 1750 52.5
37.3
0.71
62.6
2.95
17.8
74.3 1600 53.3
36.5
0.68
62.4
2.68
19.9
60
9.0
3.3
7.5
74.5 1750 53.6
37.6
0.70
63.2
2.80
19.1
70.8 1600 53.6
36.7
0.68
62.6
2.63
20.4
12.0
4.5
10.4
70.9 1750 53.9
37.9
0.70
63.2
2.74
19.7
90.8 1600 49.9
35.3
0.71
60.4
3.09
16.1
6.0
1.6
3.7
91.0 1750 50.2
36.4
0.73
61.2
3.22
15.6
84.0 1600 51.0
35.6
0.70
61.0
2.92
17.5
70
9.0
3.1
7.2
84.1 1750 51.3
36.7
0.72
61.7
3.05
16.8
80.5 1600 51.3
35.9
0.70
61.1
2.86
17.9
12.0
4.3
10.0
80.6 1750 51.6
37.0
0.72
61.8
2.99
17.3
100.3 1600 47.6
34.1
0.72
59.1
3.37
14.1
6.0
1.5
3.4
100.5 1750 47.8
35.1
0.73
59.8
3.52
13.6
93.6 1600 48.5
34.4
0.71
59.4
3.19
15.2
80
9.0
2.9
6.7
93.8 1750 48.8
35.4
0.73
60.2
3.33
14.7
90.2 1600 48.9
34.6
0.71
59.5
3.12
15.7
12.0
4.0
9.2
90.4 1750 49.2
35.7
0.73
60.3
3.26
15.1
109.8 1600 45.0
32.8
0.73
57.7
3.71
12.1
6.0
1.4
3.1
110.1 1750 45.3
33.8
0.75
58.5
3.87
11.7
103.3 1600 46.0
33.1
0.72
58.0
3.51
13.1
90
9.0
2.6
6.1
103.4 1750 46.2
34.1
0.74
58.7
3.67
12.6
100.0 1600 46.3
33.3
0.72
58.0
3.44
13.5
12.0
3.7
8.4
100.1 1750 46.5
34.3
0.74
58.7
3.59
13.0
119.4 1600 42.3
31.7
0.75
56.4
4.12
10.3
6.0
1.3
3.0
119.7 1750 42.6
32.7
0.77
57.3
4.30
9.9
112.9 1600 43.2
32.0
0.74
56.5
3.90
11.1
100
9.0
2.5
5.8
113.2 1750 43.5
33.0
0.76
57.4
4.08
10.7
109.7 1600 43.5
32.2
0.74
56.5
3.82
11.4
12.0
3.5
8.0
109.8 1750 43.7
33.2
0.76
57.3
3.99
11.0
129.0 1600 39.6
30.7
0.78
55.2
4.56
8.7
6.0
1.2
2.8
129.2 1750 39.8
31.6
0.79
56.0
4.76
8.4
122.6 1600 40.4
31.0
0.77
55.1
4.32
9.4
9.0
2.4
5.5
110
122.8 1750 40.6
31.9
0.79
56.0
4.51
9.0
119.5 1600 40.6
31.2
0.77
55.0
4.23
9.6
12.0
3.3
7.6
119.6 1750 40.9
32.1
0.78
56.0
4.42
9.3
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
EWT
°F
Flow
GPM
WPD
XT Models, Rev.: A
59
Discharge Suction Subcooling Superheat
PSIG
PSIG
°F
°F
236.5
132.2
19.1
12.2
237.2
134.5
19.0
12.4
219.7
131.5
16.0
12.8
220.4
133.7
16.0
13.1
211.7
130.7
14.8
13.7
212.4
132.9
14.7
14.0
272.8
134.4
17.6
11.1
273.7
136.6
17.5
11.4
253.4
133.6
14.6
11.7
254.3
135.9
14.5
12.0
244.2
132.9
13.3
12.6
245.0
135.1
13.2
12.9
311.1
136.5
15.9
10.1
312.1
138.8
15.8
10.4
289.1
135.7
13.2
10.8
290.0
138.0
13.0
11.1
278.5
135.0
12.0
11.7
279.4
137.2
11.7
12.0
353.1
138.9
15.0
9.3
354.3
141.2
14.7
9.6
328.1
138.1
12.5
10.0
329.2
140.4
12.4
10.3
316.1
137.3
11.6
10.9
317.2
139.6
11.3
11.2
400.2
141.2
14.2
8.9
401.5
143.6
13.8
9.1
371.8
140.4
12.2
9.6
373.1
142.7
12.0
9.9
358.3
139.6
11.5
10.5
359.5
141.9
11.2
10.7
452.2
143.1
13.3
9.1
453.7
145.5
13.0
9.3
420.1
142.3
11.5
9.8
421.5
144.7
11.1
10.0
404.8
141.5
11.0
10.6
406.1
143.9
10.6
10.9
506.2
145.0
13.3
9.4
507.9
147.4
12.9
9.7
470.3
144.1
10.8
10.1
471.8
146.6
10.4
10.4
453.2
143.3
10.2
11.0
454.6
145.7
9.7
11.3
Enertech Global
Section 11: Engineering Data
Model 060 Part Load Heating Performance Data: 5.0 Ton
Heating
LWT Airflow LAT
HC
HE
COP Discharge Suction Subcooling
°F
CFM
°F
MBtuh MBtuh kW W/W
PSIG
PSIG
°F
20.8 1450
89.9
31.2
20.3 3.19 2.86
311.0
77.4
24.4
25
10.0 5.0 11.6
20.8 1600
88.1
31.2
20.5 3.15 2.91
306.0
77.2
24.2
21.8 1450
89.7
30.9
19.9 3.23 2.80
315.0
76.9
26.4
5.0 1.5 3.4
21.7 1600
88.0
31.1
20.2 3.19 2.85
311.0
76.7
26.3
24.1 1450
90.8
32.6
21.6 3.23 2.96
319.0
81.5
25.4
30
7.5 3.0 6.9
24.0 1600
88.9
32.7
21.8 3.20 3.00
314.0
81.3
25.3
25.0 1450
92.1
34.6
24.2 3.06 3.32
299.0
83.3
23.4
10.0 4.9 11.3
25.0 1600
89.9
34.3
24.1 3.01 3.35
292.0
83.1
22.2
29.5 1450
93.0
36.0
25.4 3.10 3.40
307.0
88.2
24.4
5.0 1.4 3.2
29.3 1600
91.1
36.4
26.0 3.06 3.49
302.0
87.9
24.4
32.4 1450
94.4
38.2
27.7 3.08 3.63
308.0
94.2
22.3
40
7.5 2.8 6.5
32.3 1600
92.2
38.4
28.0 3.04 3.71
302.0
93.8
22.3
34.0 1450
95.3
39.6
29.1 3.08 3.77
310.0
97.8
21.4
10.0 4.7 10.8
33.9 1600
93.0
39.7
29.4 3.01 3.87
301.0
97.5
20.3
37.5 1450
96.2
41.0
30.4 3.11 3.87
316.0
101.5
22.4
5.0 1.3 3.1
37.4 1600
93.8
41.0
30.6 3.06 3.93
309.0
101.1
22.2
41.0 1450
97.8
43.5
32.9 3.11 4.10
320.0
109.2
20.2
50
7.5 2.7 6.3
40.8 1600
95.3
43.7
33.3 3.05 4.20
313.0
108.7
20.4
42.9 1450
98.6
44.8
34.3 3.10 4.24
322.0
113.9
18.4
10.0 4.5 10.3
42.8 1600
96.1
45.2
34.8 3.03 4.37
314.0
113.4
18.4
45.6 1450
99.2
45.7
35.0 3.14 4.27
328.0
116.1
20.3
5.0 1.3 3.0
45.3 1600
96.7
46.1
35.6 3.07 4.40
320.0
115.4
20.4
49.5 1450 101.2 48.8
38.1 3.15 4.54
335.0
125.6
18.4
60
7.5 2.6 6.0
49.4 1600
98.3
48.9
38.4 3.07 4.67
325.0
124.9
18.3
51.8 1450 102.3 50.5
39.8 3.14 4.71
338.0
131.5
16.4
10.0 4.3 9.9
51.7 1600
99.3
50.6
40.1 3.06 4.84
327.0
130.7
16.2
53.6 1450 102.4 50.8
39.9 3.20 4.66
344.0
132.1
19.4
5.0 1.2 2.9
53.3 1600
99.5
51.0
40.4 3.11 4.80
334.0
131.2
19.3
58.1 1450 104.5 54.1
43.2 3.21 4.94
353.0
143.4
17.5
70
7.5 2.5 5.8
58.0 1600 101.5 54.4
43.8 3.10 5.14
340.0
142.8
16.3
60.7 1450 105.6 55.8
44.9 3.18 5.13
354.0
150.4
14.4
10.0 4.1 9.5
60.6 1600 102.3 55.9
45.3 3.09 5.30
342.0
149.2
14.4
61.5 1450 105.7 55.9
44.8 3.25 5.04
361.0
149.4
18.4
5.0 1.2 2.8
61.3 1600 102.5 56.2
45.4 3.16 5.21
349.0
148.3
18.3
66.7 1450 108.0 59.4
48.3 3.25 5.36
369.0
162.7
15.5
80
7.5 2.4 5.6
66.5 1600 104.6 59.9
49.1 3.15 5.58
357.0
161.8
15.5
69.7 1450 109.1 61.2
50.2 3.22 5.56
371.0
170.6
12.4
10.0 4.0 9.3
69.5 1600 105.7 61.8
51.1 3.12 5.81
358.0
170.1
12.3
69.5 1450 109.0 61.0
49.7 3.31 5.41
379.0
167.9
17.5
5.0 1.2 2.7
69.2 1600 105.5 61.4
50.5 3.20 5.62
366.0
166.6
17.5
75.3 1450 111.4 64.8
53.5 3.30 5.75
388.0
183.0
14.5
7.5 2.4 5.5
90
75.1 1600 107.7 65.2
54.4 3.17 6.03
372.0
182.0
13.4
78.3 1450 113.4 67.9
56.7 3.29 6.06
394.0
196.5
11.4
10.0 4.0 9.2
78.0 1600 109.8 68.9
58.0 3.17 6.37
380.0
196.2
11.4
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
EWT
°F
Flow
WPD
GPM PSI FT
Enertech Global
60
Superheat
°F
3.7
3.6
5.0
5.1
3.9
3.7
2.9
2.8
3.3
3.4
2.7
2.7
2.4
2.3
2.9
2.8
3.0
2.9
2.8
2.8
3.2
3.2
4.1
3.9
4.3
4.2
3.8
3.8
5.4
5.2
5.9
5.9
4.6
4.7
6.9
6.7
7.8
7.6
6.0
5.8
8.6
8.5
9.4
9.3
XT Models, Rev.: A
Section 11: Engineering Data
Model 060 Full Load Heating Performance Data: 5.0 Ton
Heating
LWT Aiflow LAT
HC
HE
COP
Discharge Suction Subcooling Superheat
PSI
FT
°F
CFM
°F
MBtuh MBtuh kW
W/W
PSIG
PSIG
°F
°F
20.8
1700
93.6
43.4
30.2
3.88
3.28
301.7
65.7
26.9
3.3
25
15.0
10.5
24.3
20.7
1850
92.4
44.7
31.4
3.90
3.36
301.3
65.6
26.8
3.3
21.6
1700
93.9
43.8
30.6
3.87
3.32
305.8
66.6
29.8
4.8
7.5
3.6
8.2
21.3
1850
92.6
45.1
31.8
3.90
3.39
305.4
66.6
29.7
4.7
24.1
1700
95.4
46.6
33.1
3.95
3.46
313.6
71.3
28.2
3.6
30
11.5
6.7
15.4
23.8
1850
94.0
48.0
34.5
3.97
3.54
313.2
71.2
28.1
3.6
25.3
1700
95.9
47.5
34.0
3.96
3.52
315.4
73.5
26.3
3.0
15.0
10.1
23.3
25.1
1850
94.5
48.9
35.3
3.99
3.59
315.0
73.5
26.2
3.0
29.9
1700
97.4
50.3
36.7
4.00
3.69
321.9
81.1
27.4
3.7
7.5
3.3
7.6
29.6
1850
95.9
51.8
38.0
4.03
3.77
321.5
81.1
27.3
3.7
32.9
1700
99.1
53.5
39.6
4.08
3.84
330.1
86.8
25.3
3.3
40
11.5
6.2
14.3
32.6
1850
97.6
55.1
41.1
4.11
3.93
329.7
86.7
25.3
3.2
34.4
1700
99.7
54.5
40.5
4.10
3.90
332.0
89.6
23.4
3.0
15.0
9.4
21.7
34.2
1850
98.1
56.2
42.1
4.12
4.00
331.6
89.5
23.3
3.0
38.3
1700 100.9 56.8
42.6
4.15
4.01
338.6
96.3
24.9
3.6
7.5
3.1
7.1
37.8
1850
99.3
58.5
44.3
4.17
4.11
338.2
96.3
24.9
3.5
41.8
1700 102.9 60.4
46.0
4.23
4.18
347.2
103.0
22.6
3.9
50
11.5
5.8
13.3
41.4
1850 101.2 62.3
47.8
4.25
4.30
346.7
103.0
22.5
3.9
43.5
1700 103.6 61.6
47.1
4.24
4.26
349.2
106.3
20.4
3.9
15.0
8.7
20.1
43.3
1850 101.7 63.4
48.8
4.27
4.35
348.7
106.3
20.3
3.9
46.6
1700 104.7 63.7
48.9
4.33
4.31
360.2
112.8
23.2
4.2
7.5
2.8
6.6
46.1
1850 102.8 65.6
50.7
4.36
4.41
359.8
112.7
23.2
4.2
50.5
1700 106.9 67.8
52.8
4.41
4.51
369.4
120.7
20.6
5.3
60
11.5
5.3
12.3
50.2
1850 105.0 69.9
54.8
4.44
4.61
368.9
120.6
20.5
5.2
52.6
1700 107.6 69.1
54.0
4.43
4.57
371.5
124.5
18.2
5.7
15.0
8.1
18.7
52.3
1850 105.6 71.2
56.0
4.46
4.68
371.0
124.4
18.1
5.7
54.8
1700 108.5 70.7
55.2
4.54
4.56
383.2
131.0
21.9
5.2
7.5
2.7
6.2
54.3
1850 106.4 72.8
57.2
4.57
4.67
382.7
130.9
21.8
5.3
59.4
1700 111.0 75.2
59.4
4.63
4.76
392.9
140.1
18.9
7.1
70
11.5
5.0
11.6
59.0
1850 108.8 77.5
61.6
4.66
4.87
392.4
140.0
18.8
7.0
61.7
1700 111.7 76.6
60.7
4.65
4.83
395.2
144.6
16.3
7.8
15.0
7.6
17.5
61.4
1850 109.5 78.9
62.9
4.68
4.94
394.7
144.5
16.2
7.8
63.2
1700 112.1 77.3
61.0
4.77
4.75
403.5
150.8
20.4
6.4
7.5
2.6
5.9
62.6
1850 109.8 79.6
63.2
4.80
4.86
403.0
150.7
20.3
6.4
68.2
1700 114.8 82.2
65.6
4.87
4.95
413.8
161.3
17.2
8.9
80
11.5
4.8
11.1
67.8
1850 112.4 84.7
68.0
4.89
5.08
413.2
161.2
17.1
8.8
70.8
1700 115.6 83.7
67.0
4.88
5.03
416.1
166.4
14.3
10.0
15.0
7.3
16.7
70.4
1850 113.2 86.3
69.5
4.91
5.15
415.6
166.3
14.2
9.9
71.6
1700 115.7 83.9
66.8
5.01
4.91
424.3
171.3
19.0
8.0
7.5
2.4
5.6
71.0
1850 113.2 86.4
69.2
5.04
5.02
423.8
171.2
18.9
7.9
77.1
1700 118.6 89.2
71.8
5.11
5.12
435.1
183.2
15.6
11.1
11.5
4.6
10.6
90
76.7
1850 116.0 91.9
74.4
5.14
5.24
434.5
183.1
15.5
11.0
79.9
1700 119.5 90.9
73.4
5.13
5.19
437.6
189.1
12.6
12.4
15.0
7.0
16.0
79.5
1850 116.9 93.7
76.1
5.16
5.32
437.0
188.9
12.5
12.4
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
EWT
°F
Flow
GPM
WPD
XT Models, Rev.: A
61
Enertech Global
Section 11: Engineering Data
Model 060 Part Load Cooling Performance Data: 5.0 Ton
Cooling
LWT Aiflow
EWT Flow WPD
TC
SC
HR
EER
Discharge Suction Subcooling Superheat
°F
GPM PSI FT
°F
CFM MBtuh MBtuh S/T MBtuh kW Btuh/W
PSIG
PSIG
°F
°F
74.7 1450
51.8
33.7 0.65 59.9 2.37
21.9
237.0
129.6
25.5
12.4
5.0 1.1 2.5
75.2 1650
53.0
35.7 0.67 61.1 2.38
22.3
240.0
132.9
25.4
12.1
66.7 1450
53.6
34.5 0.64 60.8 2.13
25.2
203.0
127.3
20.4
12.8
50
7.5 2.2 5.2
67.1 1650
54.9
36.4 0.66 62.1 2.13
25.7
205.0
130.6
20.3
12.4
62.7 1450
54.5
34.9 0.64 61.4 2.02
27.0
187.0
126.0
18.4
13.0
10.0 3.7 8.6
63.0 1650
56.0
36.9 0.66 62.9 2.03
27.6
190.0
129.4
19.4
12.7
84.0 1450
49.3
32.8 0.67 58.3 2.62
18.8
274.0
133.3
25.6
9.4
5.0 1.1 2.4
84.5 1650
50.4
34.8 0.69 59.4 2.63
19.2
277.0
136.4
25.5
8.9
76.2 1450
51.0
33.5 0.66 59.1 2.36
21.6
237.0
131.1
20.4
10.0
60
7.5 2.2 5.0
76.6 1650
52.2
35.5 0.68 60.3 2.37
22.1
240.0
134.2
20.5
9.3
72.3 1450
52.0
33.9 0.65 59.6 2.24
23.2
220.0
130.0
18.3
10.1
10.0 3.6 8.3
72.5 1650
53.2
36.0 0.68 60.8 2.24
23.7
222.0
133.0
18.5
9.8
93.3 1450
46.7
31.8 0.68 56.6 2.91
16.0
314.0
137.0
25.6
6.9
5.0 1.0 2.4
93.7 1650
47.6
34.0 0.71 57.5 2.92
16.3
317.0
139.8
25.7
6.3
85.8 1450
48.4
32.4 0.67 57.3 2.63
18.4
275.0
134.8
20.4
7.3
70
7.5 2.1 4.9
86.1 1650
49.4
34.6 0.70 58.4 2.63
18.8
278.0
137.8
20.6
6.6
81.9 1450
49.3
32.8 0.67 57.8 2.50
19.7
257.0
133.7
18.4
7.6
10.0 3.5 8.1
82.1 1650
50.4
35.0 0.70 58.9 2.50
20.2
259.0
136.6
18.5
7.0
102.6 1450
43.9
30.8 0.70 54.9 3.22
13.6
355.0
140.2
24.6
6.5
5.0 1.0 2.4
103.0 1650
44.7
32.9 0.74 55.7 3.23
13.9
358.0
142.9
24.7
6.0
95.3 1450
45.6
31.4 0.69 55.5 2.93
15.6
317.0
138.1
20.6
6.9
80
7.5 2.1 4.8
46.5
33.5 0.72 56.5 2.93
15.9
319.0
140.9
20.6
6.4
95.5 1650
91.5 1450
46.4
31.8 0.68 56.0 2.79
16.7
298.0
137.0
18.6
7.3
10.0 3.4 8.0
91.7 1650
47.4
33.9 0.71 56.9 2.79
17.0
300.0
139.8
18.6
6.6
111.9 1450
41.1
29.7 0.72 53.2 3.55
11.6
400.0
143.4
23.7
7.2
5.0 1.0 2.4
112.3 1650
41.8
31.8 0.76 54.0 3.56
11.7
403.0
146.0
23.7
6.9
104.8 1450
42.7
30.3 0.71 53.8 3.25
13.1
360.0
141.4
19.6
7.6
90
7.5 2.1 4.8
105.0 1650
43.6
32.4 0.74 54.7 3.27
13.3
364.0
143.9
20.6
7.1
101.2 1450
43.5
30.6 0.70 54.1 3.10
14.0
341.0
140.4
17.6
8.0
10.0 3.4 7.9
101.4 1650
44.5
32.7 0.74 55.1 3.12
14.2
345.0
143.0
18.7
7.3
121.3 1450
38.2
28.4 0.75 51.6 3.93
9.7
450.0
147.1
22.8
7.2
5.0 1.0 2.4
121.6 1650
38.9
30.8 0.79 52.4 3.96
9.8
454.0
149.2
23.6
7.1
11.0
408.0
145.0
18.8
7.8
114.3 1450
39.7
29.2 0.73 52.0 3.61
100
7.5 2.1 4.8
114.5 1650
40.5
31.1 0.77 52.9 3.63
11.1
412.0
147.5
19.7
7.2
110.8 1450
40.5
29.4 0.73 52.4 3.47
11.7
390.0
143.9
17.7
7.8
10.0 3.5 8.0
111.0 1650
41.3
31.6 0.77 53.1 3.48
11.9
392.0
146.3
17.7
7.6
130.7 1450
35.3
27.6 0.78 50.1 4.36
8.1
503.0
150.1
22.6
8.0
5.0 1.1 2.4
131.0 1650
35.9
29.5 0.82 50.8 4.37
8.2
506.0
152.7
22.6
7.3
123.8 1450
36.6
27.9 0.76 50.3 4.01
9.1
460.0
148.6
17.8
8.2
7.5 2.1 4.9
110
124.0 1650
37.3
29.9 0.80 51.0 4.02
9.3
462.0
151.0
17.7
7.7
120.4 1450
37.4
28.1 0.75 50.5 3.85
9.7
439.0
147.8
15.7
8.3
10.0 3.5 8.1
120.6 1650
38.0
30.4 0.80 51.2 3.85
9.9
440.0
149.9
15.7
8.1
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
Enertech Global
62
XT Models, Rev.: A
Section 11: Engineering Data
Model 060 Full Load Cooling Performance Data: 5.0 Ton
Cooling
LWT
EWT Flow
WPD
Aiflow TC
SC
HR
EER
°F
GPM
PSI
FT
°F
CFM MBtuh MBtuh S/T MBtuh kW
Btuh/W
71.7 1750 67.7
43.1
0.64
78.8
3.25
20.8
7.5
2.6
6.0
72.1 1950 68.8
45.6
0.66
80.4
3.40
20.2
64.1 1750 68.0
43.3
0.64
78.5
3.07
22.1
50
11.5
5.3
12.2
64.4 1950 69.2
45.8
0.66
80.1
3.20
21.6
60.7 1750 68.0
43.4
0.64
78.2
2.99
22.7
15.0
8.2
19.0
61.0 1950 69.2
45.9
0.66
79.9
3.13
22.1
81.6 1750 66.4
42.5
0.64
78.4
3.51
18.9
7.5
2.4
5.6
82.0 1950 67.5
44.9
0.67
80.0
3.67
18.4
74.0 1750 66.7
42.7
0.64
78.0
3.31
20.2
60
11.5
4.9
11.4
74.3 1950 67.9
45.1
0.66
79.7
3.46
19.6
70.7 1750 66.7
42.8
0.64
77.7
3.23
20.7
15.0
7.7
17.7
70.9 1950 67.9
45.3
0.67
79.4
3.38
20.1
91.4 1750 64.8
41.8
0.65
77.8
3.80
17.1
7.5
2.3
5.2
91.9 1950 66.0
44.2
0.67
79.5
3.97
16.6
83.9 1750 65.1
42.0
0.65
77.3
3.58
18.2
70
11.5
4.6
10.6
84.2 1950 66.3
44.4
0.67
79.1
3.74
17.7
80.6 1750 65.2
42.1
0.65
77.1
3.49
18.7
15.0
7.2
16.5
80.8 1950 66.3
44.5
0.67
78.8
3.65
18.2
101.0 1750 62.3
40.8
0.65
76.4
4.13
15.1
7.5
2.2
5.0
101.5 1950 63.4
43.1
0.68
78.1
4.31
14.7
93.6 1750 62.6
41.0
0.65
75.9
3.89
16.1
80
11.5
4.4
10.1
93.9 1950 63.7
43.3
0.68
77.6
4.07
15.7
90.4 1750 62.6
41.1
0.66
75.6
3.80
16.5
15.0
6.8
15.7
90.6 1950 63.7
43.4
0.68
77.2
3.97
16.0
110.5 1750 59.1
39.5
0.67
74.6
4.53
13.0
7.5
2.1
4.8
111.0 1950 60.1
41.8
0.70
76.3
4.74
12.7
103.3 1750 59.4
39.7
0.67
74.0
4.27
13.9
90
11.5
4.2
9.7
103.6 1950 60.4
42.0
0.70
75.6
4.46
13.5
100.1 1750 59.4
39.8
0.67
73.6
4.17
14.2
15.0
6.5
15.1
100.4 1950 60.5
42.1
0.70
75.4
4.36
13.9
120.0 1750 55.8
38.1
0.68
72.9
5.01
11.1
7.5
2.0
4.6
120.5 1950 56.8
40.3
0.71
74.7
5.24
10.8
112.9 1750 56.1
38.3
0.68
72.2
4.72
11.9
100
11.5
4.0
9.3
113.3 1950 57.1
40.5
0.71
74.0
4.94
11.6
109.9 1750 56.1
38.4
0.68
71.8
4.61
12.2
15.0
6.3
14.5
110.1 1950 57.1
40.6
0.71
73.5
4.82
11.8
129.5 1750 52.3
36.5
0.70
71.1
5.52
9.5
7.5
1.9
4.5
130.0 1950 53.2
38.6
0.73
72.9
5.76
9.2
122.6 1750 52.5
36.7
0.70
70.2
5.20
10.1
11.5
3.9
9.0
110
122.9 1950 53.5
38.8
0.73
72.1
5.44
9.8
119.6 1750 52.6
36.8
0.70
69.9
5.08
10.4
15.0
6.1
14.1
119.8 1950 53.5
38.9
0.73
71.6
5.31
10.1
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
XT Models, Rev.: A
63
Discharge Suction Subcooling Superheat
PSIG
PSIG
°F
°F
238.3
124.2
27.8
13.8
239.1
129.5
28.0
13.5
218.8
123.5
23.1
14.3
219.6
128.9
23.2
13.9
210.7
123.5
20.9
14.5
211.4
128.8
21.1
14.2
274.0
126.5
28.0
10.5
274.9
132.0
28.2
10.0
251.6
125.8
23.0
10.9
252.4
131.3
23.2
10.5
242.2
125.8
20.7
11.1
243.0
131.2
20.9
10.7
311.8
128.8
27.8
7.6
312.8
134.4
27.9
7.0
286.3
128.1
22.8
8.0
287.3
133.7
22.9
7.5
275.7
128.1
20.4
8.2
276.6
133.6
20.6
7.7
354.6
131.2
27.3
7.1
355.8
136.9
27.4
6.6
325.6
130.5
22.6
7.6
326.7
136.2
22.7
7.1
313.5
130.5
20.3
7.8
314.6
136.1
20.4
7.3
402.7
133.7
26.4
7.8
404.1
139.4
26.6
7.4
369.8
132.9
22.1
8.3
371.1
138.7
22.2
7.8
356.1
132.9
19.9
8.5
357.3
138.6
20.1
8.1
454.9
136.1
25.4
7.8
456.5
141.9
25.5
7.3
417.8
135.3
21.0
8.3
419.2
141.2
21.1
7.8
402.2
135.3
18.9
8.5
403.6
141.1
19.1
8.0
509.3
138.5
25.0
8.2
511.0
144.4
25.2
7.8
467.7
137.7
19.6
8.7
469.2
143.7
19.8
8.3
450.3
137.7
17.4
8.9
451.8
143.6
17.6
8.5
Enertech Global
Section 11: Engineering Data
Model 072 Part Load Heating Performance Data: 6.0 Ton
Heating
LWT Aiflow LAT
HC
HE
COP Discharge Suction Subcooling
°F
CFM
°F
MBtuh MBtuh kW W/W
PSIG
PSIG
°F
20.5 1650
92.1
39.4
26.3 3.82 3.02
322.0
79.5
21.3
25
12.0 5.0 11.5
20.4 1850
89.7
39.4
26.6 3.73 3.09
314.0
79.2
20.2
21.0 1650
92.1
39.3
26.1 3.87 2.98
327.0
79.2
23.2
6.0 1.5 3.4
21.0 1850
89.6
39.2
26.3 3.79 3.03
320.0
78.9
22.4
23.6 1650
93.1
41.2
27.9 3.89 3.10
332.0
84.0
23.2
30
9.0 3.0 6.8
23.5 1850
90.7
41.3
28.3 3.81 3.18
324.0
83.7
22.3
25.0 1650
93.6
42.1
28.8 3.88 3.18
333.0
86.7
22.4
12.0 4.9 11.3
25.0 1850
91.0
42.0
29.1 3.79 3.25
324.0
86.5
21.2
29.4 1650
94.7
44.0
30.7 3.91 3.31
339.0
91.6
22.4
6.0 1.4 3.2
29.4 1850
92.0
44.0
31.0 3.81 3.38
329.0
91.2
21.3
32.4 1650
96.0
46.3
33.1 3.87 3.51
339.0
97.6
19.4
40
9.0 2.8 6.5
32.3 1850
93.2
46.3
33.4 3.77 3.60
329.0
97.3
18.5
34.1 1650
96.6
47.5
34.3 3.87 3.60
341.0
101.2
18.3
12.0 4.6 10.7
34.0 1850
93.8
47.6
34.7 3.76 3.70
330.0
100.8
17.2
37.7 1650
97.5
49.1
35.7 3.92 3.67
348.0
105.0
19.4
6.0 1.3 3.1
37.6 1850
94.6
49.2
36.2 3.80 3.79
336.0
104.5
18.2
41.2 1650
99.0
51.6
38.3 3.90 3.88
351.0
112.7
16.4
50
9.0 2.7 6.2
41.1 1850
95.9
51.7
38.8 3.78 4.01
339.0
112.1
15.4
43.2 1650
99.8
53.1
39.8 3.89 4.00
352.0
117.2
14.3
12.0 4.4 10.2
43.1 1850
96.7
53.3
40.4 3.79 4.13
342.0
116.6
14.3
45.9 1650 100.7 54.6
41.0 3.99 4.01
364.0
120.0
18.4
6.0 1.3 3.0
45.7 1850
97.5
54.9
41.6 3.88 4.14
353.0
119.3
18.4
49.9 1650 102.4 57.7
44.1 3.99 4.24
369.0
129.5
15.4
60
9.0 2.6 6.0
49.8 1850
99.0
57.9
44.7 3.85 4.40
355.0
128.9
14.3
52.1 1650 103.3 59.4
45.8 3.98 4.37
372.0
135.1
13.5
12.0 4.3 9.8
52.0 1850
99.9
59.7
46.6 3.86 4.53
359.0
134.4
13.3
54.0 1650 104.1 60.7
46.6 4.13 4.31
386.0
136.2
19.4
6.0 1.2 2.9
53.8 1850 100.4 60.8
47.3 3.97 4.49
371.0
135.3
18.4
58.5 1650 106.0 64.1
50.1 4.11 4.57
391.0
147.8
15.5
70
9.0 2.5 5.8
58.3 1850 102.3 64.5
51.0 3.97 4.76
377.0
146.7
15.5
61.1 1650 107.1 66.1
52.1 4.11 4.72
394.0
154.3
13.4
12.0 4.1 9.5
60.9 1850 103.3 66.5
53.0 3.96 4.92
380.0
153.4
13.5
62.0 1650 107.5 66.8
52.4 4.22 4.64
405.0
153.4
18.5
6.0 1.2 2.8
61.7 1850 103.6 67.0
53.1 4.07 4.82
390.0
152.1
18.5
67.0 1650 109.8 71.0
56.5 4.23 4.91
413.0
166.7
15.4
80
9.0 2.4 5.6
66.9 1850 105.6 71.2
57.3 4.05 5.15
395.0
165.6
14.5
69.9 1650 111.1 73.3
58.8 4.23 5.07
417.0
174.4
13.4
12.0 4.0 9.2
69.8 1850 106.7 73.4
59.5 4.05 5.31
399.0
173.3
12.4
70.0 1650 111.1 73.2
58.3 4.38 4.90
429.0
171.3
19.4
6.0 1.2 2.7
69.7 1850 106.7 73.3
59.1 4.18 5.14
409.0
169.8
18.4
75.6 1650 113.5 77.6
62.7 4.37 5.21
436.0
186.4
15.5
9.0 2.4 5.5
90
75.4 1850 108.9 77.8
63.6 4.16 5.48
415.0
184.9
14.4
78.8 1650 114.8 79.9
65.0 4.36 5.36
441.0
195.2
13.5
12.0 3.9 9.1
78.6 1850 110.2 80.3
66.1 4.15 5.67
420.0
193.8
12.5
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
EWT
°F
Flow
WPD
GPM PSI FT
Enertech Global
64
Superheat
°F
4.4
4.5
2.9
3.2
1.8
2.0
1.4
1.6
1.8
2.0
1.4
1.6
1.3
1.5
1.7
1.8
2.0
2.3
2.4
2.6
1.3
1.4
2.3
2.5
3.0
3.1
1.5
1.7
3.1
3.4
4.3
4.4
3.3
3.5
5.7
5.9
7.0
7.2
5.3
5.7
8.3
8.6
10.0
10.2
XT Models, Rev.: A
Section 11: Engineering Data
Model 072 Full Load Heating Performance Data: 6.0 Ton
Heating
LWT Aiflow LAT
HC
HE
COP
Discharge Suction Subcooling Superheat
PSI
FT
°F
CFM
°F
MBtuh MBtuh kW
W/W
PSIG
PSIG
°F
°F
20.9
2000
94.4
52.6
36.2
4.80
3.21
301.6
66.5
23.7
4.2
25
18.0
10.3
23.7
20.7
2100
93.6
53.6
37.3
4.79
3.28
298.6
66.1
23.0
4.5
21.2
2000
95.6
55.2
38.4
4.91
3.29
310.9
70.1
28.3
2.6
7.6
9.0
3.3
21.0
2100
94.8
56.2
39.5
4.90
3.36
307.8
69.7
27.7
2.9
23.9
2000
96.4
57.0
40.2
4.93
3.39
315.7
75.1
25.8
1.5
13.5
6.6
15.2
30
23.7
2100
95.6
58.1
41.3
4.92
3.46
312.5
74.7
25.1
1.8
25.3
2000
96.9
58.0
41.1
4.96
3.43
318.1
77.2
24.5
1.3
18.0
10.0
23.1
25.2
2100
96.1
59.1
42.2
4.94
3.51
315.0
76.8
23.9
1.5
29.7
2000
98.8
62.3
45.1
5.05
3.62
326.1
84.8
24.5
1.9
9.0
3.1
7.1
29.4
2100
98.0
63.4
46.2
5.04
3.69
322.9
84.3
23.9
2.1
32.8
2000
99.8
64.4
47.1
5.07
3.72
331.1
90.9
21.6
1.6
40
13.5
6.1
14.2
32.6
2100
98.9
65.6
48.3
5.06
3.80
327.8
90.4
21.0
1.7
34.5
2000 100.4 65.6
48.2
5.10
3.77
333.7
93.4
20.1
1.7
18.0
9.3
21.6
34.3
2100
99.4
66.7
49.4
5.08
3.85
330.4
92.9
19.5
1.9
38.2
2000 102.2 69.5
51.7
5.21
3.91
342.7
99.9
21.1
2.1
9.0
2.9
6.6
37.8
2100 101.2 70.8
53.1
5.20
3.99
339.2
99.4
20.5
2.4
41.8
2000 103.3 71.9
54.0
5.24
4.02
347.9
107.1
17.8
2.7
13.2
50
13.5
5.7
41.5
2100 102.3 73.2
55.4
5.22
4.11
344.4
106.5
17.2
2.9
43.7
2000 103.9 73.2
55.3
5.26
4.08
350.6
110.0
16.2
3.2
18.0
8.7
20.1
43.5
2100 102.8 74.5
56.6
5.25
4.16
347.1
109.5
15.6
3.4
46.4
2000 106.2 78.2
59.5
5.48
4.18
368.4
117.5
20.6
2.0
6.3
9.0
2.7
46.0
2100 105.1 79.6
61.0
5.46
4.27
364.7
117.0
20.0
2.1
50.5
2000 107.4 80.8
62.0
5.50
4.31
374.0
126.0
17.0
3.2
13.5
5.4
12.5
60
50.3
2100 106.3 82.3
63.6
5.49
4.39
370.2
125.4
16.4
3.4
52.7
2000 108.1 82.3
63.4
5.53
4.36
376.9
129.5
15.2
4.1
18.0
8.3
19.1
52.6
2100 106.9 83.7
64.9
5.51
4.45
373.2
128.8
14.7
4.4
54.6
2000 110.3 87.1
67.3
5.79
4.41
397.5
136.3
21.1
2.4
6.0
9.0
2.6
54.2
2100 109.1 88.6
68.9
5.78
4.49
393.6
135.6
20.6
2.7
59.3
2000 111.7 90.0
70.1
5.82
4.53
403.6
146.1
17.3
4.4
70
13.5
5.2
12.0
59.0
2100 110.4 91.6
71.8
5.80
4.63
399.6
145.3
16.7
4.7
61.8
2000 112.4 91.6
71.7
5.84
4.60
406.7
150.1
15.4
5.7
18.0
7.9
18.3
61.6
2100 111.1 93.3
73.4
5.83
4.69
402.7
149.3
14.8
5.9
63.0
2000 114.0 95.0
74.2
6.09
4.57
423.4
154.1
20.9
4.5
9.0
2.5
5.8
62.6
2100 112.6 96.7
76.0
6.08
4.66
419.2
153.4
20.3
4.8
68.2
2000 115.5 98.3
77.4
6.12
4.71
429.9
165.2
16.9
7.3
80
13.5
5.0
11.5
67.9
2100 114.1 100.0 79.2
6.10
4.80
425.6
164.4
16.3
7.6
71.0
2000 116.3 100.0 79.0
6.15
4.77
433.2
169.8
14.9
9.0
18.0
7.6
17.6
70.7
2100 114.9 101.8 80.9
6.13
4.87
428.9
168.9
14.3
9.2
71.4
2000 117.7 103.1 81.2
6.41
4.71
450.7
172.4
21.2
7.0
9.0
2.4
5.6
70.9
2100 116.3 105.0 83.2
6.40
4.81
446.2
171.6
20.6
7.3
77.1
2000 119.4 106.6 84.6
6.44
4.85
457.6
184.8
17.0
10.5
13.5
4.8
11.2
90
76.8
2100 117.9 108.6 86.7
6.43
4.95
453.0
183.9
16.4
10.8
80.1
2000 120.2 108.5 86.4
6.47
4.91
461.2
189.9
15.0
12.5
18.0
7.4
17.0
79.9
2100 118.7 110.5 88.5
6.46
5.01
456.6
189.0
14.3
12.8
Heating data based on 70 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
EWT
°F
Flow
GPM
WPD
XT Models, Rev.: A
65
Enertech Global
Section 11: Engineering Data
Model 072 Part Load Cooling Performance Data: 6.0 Ton
Cooling
LWT Aiflow
TC
SC
HR
EER
Discharge Suction Subcooling
°F
CFM MBtuh MBtuh S/T MBtuh kW Btuh/W
PSIG
PSIG
°F
73.6 1600
58.8
37.7 0.64 68.7 2.91
20.2
230.0
136.0
22.3
6.0 1.3 2.9
74.0 1750
59.7
39.2 0.66 69.7 2.92
20.5
232.0
137.9
22.3
65.9 1600
60.4
38.3 0.64 69.4 2.64
22.9
196.0
134.2
18.1
50
9.0 2.6 6.1
66.1 1750
61.4
39.8 0.65 70.4 2.64
23.3
198.0
136.2
18.2
62.0 1600
61.3
38.8 0.63 69.9 2.51
24.4
181.0
132.9
17.1
12.0 4.4 10.1
62.2 1750
62.3
40.3 0.65 70.9 2.51
24.8
182.0
134.7
17.1
83.2 1600
56.5
36.8 0.65 67.5 3.24
17.4
268.0
138.6
23.3
6.0 1.2 2.8
83.5 1750
57.4
38.3 0.67 68.5 3.25
17.7
270.0
140.4
23.4
75.6 1600
58.0
37.4 0.64 68.0 2.93
19.8
232.0
136.8
19.2
60
9.0 2.5 5.9
75.8 1750
59.0
39.0 0.66 69.0 2.93
20.1
234.0
138.7
19.3
71.8 1600
58.9
37.7 0.64 68.4 2.79
21.1
215.0
135.7
17.3
12.0 4.2 9.7
71.9 1750
59.9
39.3 0.66 69.4 2.79
21.5
216.0
137.5
17.2
92.8 1600
54.1
35.9 0.66 66.4 3.61
15.0
310.0
141.2
24.3
6.0 1.2 2.8
93.1 1750
54.9
37.5 0.68 67.3 3.62
15.2
312.0
142.9
24.4
85.3 1600
55.5
36.3 0.65 66.7 3.26
17.0
271.0
139.7
19.3
70
9.0 2.5 5.7
85.5 1750
56.4
37.9 0.67 67.6 3.26
17.3
272.0
141.4
19.2
81.5 1600
56.5
36.7 0.65 67.1 3.11
18.1
254.0
138.5
18.4
12.0 4.1 9.5
81.7 1750
57.4
38.3 0.67 68.0 3.11
18.4
255.0
140.1
18.3
102.4 1600
51.5
34.9 0.68 65.2 4.03
12.8
356.0
144.2
24.6
6.0 1.2 2.8
102.7 1750
52.2
36.5 0.70 66.0 4.04
12.9
357.0
145.7
24.5
95.0 1600
52.9
35.5 0.67 65.4 3.65
14.5
315.0
142.5
20.3
80
9.0 2.4 5.6
95.2 1750
53.8
37.0 0.69 66.3 3.66
14.7
317.0
144.0
20.5
91.3 1600
53.8
35.7 0.66 65.6 3.48
15.5
296.0
141.4
18.4
12.0 4.1 9.3
91.4 1750
54.7
37.2 0.68 66.5 3.48
15.7
297.0
143.1
18.4
112.0 1600
48.8
33.9 0.70 64.1 4.49
10.8
405.0
147.0
24.5
6.0 1.2 2.8
112.3 1750
49.6
35.2 0.71 64.9 4.51
11.0
407.0
148.8
24.5
104.7 1600
50.2
34.4 0.69 64.1 4.09
12.3
363.0
145.4
20.5
90
9.0 2.4 5.6
104.9 1750
51.0
36.0 0.71 64.9 4.09
12.5
364.0
146.9
20.4
101.0 1600
51.0
34.7 0.68 64.3 3.90
13.1
342.0
144.3
18.4
12.0 4.0 9.3
101.2 1750
51.9
36.4 0.70 65.3 3.92
13.2
345.0
145.7
19.4
121.6 1600
45.9
32.9 0.72 62.9 4.98
9.2
455.0
150.0
23.6
6.0 1.2 2.8
121.9 1750
46.7
34.4 0.74 63.7 4.99
9.4
456.0
151.5
23.4
114.4 1600
47.2
33.3 0.71 62.8 4.56
10.4
412.0
148.5
19.5
100
9.0 2.5 5.7
114.6 1750
48.1
34.9 0.73 63.7 4.59
10.5
416.0
149.9
20.6
110.8 1600
48.1
33.6 0.70 63.0 4.37
11.0
393.0
147.4
18.5
12.0 4.1 9.4
111.0 1750
48.9
35.1 0.72 63.8 4.38
11.2
394.0
148.8
18.4
131.4 1600
43.3
31.6 0.73 62.2 5.54
7.8
511.0
153.2
23.5
6.0 1.2 2.9
131.7 1750
44.0
33.2 0.75 63.1 5.58
7.9
515.0
154.4
24.4
124.1 1600
44.4
32.3 0.73 61.7 5.08
8.7
466.0
151.5
19.5
9.0 2.5 5.8
110
124.3 1750
45.1
33.8 0.75 62.5 5.08
8.9
467.0
152.9
19.5
120.6 1600
45.1
32.5 0.72 61.7 4.88
9.2
445.0
150.6
17.5
12.0 4.1 9.5
120.8 1750
45.9
34.1 0.74 62.6 4.91
9.4
449.0
151.8
18.5
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data based on simulation, expected accuracy within ± 15%
Discharge pressure is ± 40 PSI; Suction pressure is ± 20 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
Brine pressure drop WPD is ± 1 PSI
EWT
°F
Flow
WPD
GPM PSI FT
Enertech Global
66
Superheat
°F
4.3
5.8
4.6
6.0
6.2
7.7
3.7
5.2
4.0
5.4
5.5
7.1
3.1
4.7
3.5
4.9
4.9
6.6
2.6
4.2
2.9
4.5
4.5
6.1
2.5
3.9
2.6
4.2
4.3
5.6
2.5
4.0
2.7
4.3
4.3
6.0
2.4
3.9
2.9
4.4
4.5
6.4
XT Models, Rev.: A
Section 11: Engineering Data
Model 072 Full Load Cooling Performance Data: 6.0 Ton
Cooling
LWT Aiflow
TC
SC
HR
EER
Discharge Suction Subcooling Superheat
PSI
FT
°F
CFM MBtuh MBtuh S/T MBtuh kW Btuh/W
PSIG
PSIG
°F
°F
71.0 1900 78.3
47.1
0.60
91.5
3.87
20.2
234.0
124.6
25.0
4.9
9.0
3.0
6.9
71.1 2150 78.3
48.2
0.62
92.3
4.11
19.1
235.7
127.8
25.3
6.6
63.9 1900 78.9
47.5
0.60
91.3
3.64
21.7
215.0
124.4
20.4
5.2
50
13.5
5.8
13.4
64.1 2150 78.9
48.7
0.62
92.1
3.87
20.4
216.6
127.6
20.7
6.9
60.5 1900 79.3
48.4
0.61
91.5
3.57
22.2
208.9
124.3
18.9
6.9
18.0
8.6
19.8
60.6 2150 79.3
49.6
0.63
92.3
3.80
20.9
210.4
127.5
19.2
8.7
80.8 1900 76.3
46.3
0.61
90.6
4.18
18.3
269.9
127.8
26.1
4.2
9.0
2.9
6.6
80.9 2150 76.3
47.5
0.62
91.4
4.44
17.2
271.8
131.1
26.4
5.8
73.8 1900 76.9
46.7
0.61
90.3
3.94
19.5
248.0
127.6
21.2
4.4
60
13.5
5.6
12.9
73.9 2150 76.9
47.9
0.62
91.2
4.18
18.4
249.7
130.9
21.6
6.2
70.4 1900 77.3
47.6
0.62
90.5
3.86
20.0
240.9
127.4
19.6
6.2
18.0
8.3
19.2
70.5 2150 77.3
48.8
0.63
91.3
4.10
18.9
242.6
130.8
19.9
8.0
90.5 1900 74.1
45.4
0.61
89.5
4.52
16.4
307.7
130.8
26.7
3.5
9.0
2.8
6.4
90.7 2150 74.1
46.5
0.63
90.5
4.81
15.4
309.9
134.2
27.0
5.2
83.6 1900 74.6
45.8
0.61
89.1
4.26
17.5
282.7
130.6
21.9
3.9
70
13.5
5.4
12.5
83.8 2150 74.6
47.0
0.63
90.1
4.53
16.5
284.7
134.0
22.2
5.6
80.2 1900 75.0
46.7
0.62
89.3
4.18
17.9
274.7
130.5
20.1
5.5
18.0
8.1
18.6
80.3 2150 75.0
47.9
0.64
90.1
4.44
16.9
276.6
133.9
20.5
7.3
100.2 1900 71.2
44.4
0.62
88.0
4.92
14.5
349.0
133.7
27.0
2.9
9.0
2.7
6.2
100.4 2150 71.2
45.5
0.64
89.0
5.23
13.6
351.4
137.2
27.2
4.6
93.4 1900 71.8
44.8
0.62
87.6
4.63
15.5
320.6
133.5
22.3
3.3
80
13.5
5.2
12.1
93.5 2150 71.8
45.9
0.64
88.6
4.93
14.6
322.9
136.9
22.6
5.0
90.0 1900 72.1
45.6
0.63
87.6
4.55
15.8
311.5
133.4
20.6
5.0
18.0
7.8
17.9
90.1 2150 72.1
46.8
0.65
88.6
4.83
14.9
313.7
136.8
20.9
6.8
109.7 1900 67.7
42.9
0.63
86.1
5.40
12.5
395.2
136.3
26.8
2.5
9.0
2.6
6.0
110.0 2150 67.7
44.0
0.65
87.3
5.75
11.8
398.0
139.8
26.9
4.2
103.1 1900 68.2
43.4
0.64
85.6
5.09
13.4
363.1
136.0
22.4
2.8
90
13.5
5.1
11.7
103.2 2150 68.2
44.4
0.65
86.7
5.41
12.6
365.7
139.6
22.7
4.6
99.8 1900 68.5
44.2
0.65
85.5
4.99
13.7
352.8
135.9
20.9
4.7
18.0
7.5
17.3
99.9 2150 68.5
45.3
0.66
86.6
5.31
12.9
355.3
139.5
21.2
6.4
119.2 1900 63.6
41.0
0.64
84.0
5.97
10.7
446.5
138.4
26.3
2.4
9.0
2.5
5.9
119.5 2150 63.6
42.0
0.66
85.3
6.35
10.0
449.7
142.0
26.5
4.2
112.7 1900 64.1
41.4
0.65
83.3
5.62
11.4
410.2
138.2
22.1
2.8
100
13.5
4.9
11.4
112.9 2150 64.1
42.4
0.66
84.5
5.98
10.7
413.1
141.8
22.2
4.6
109.5 1900 64.4
42.2
0.66
83.2
5.52
11.7
398.5
138.1
20.6
4.5
18.0
7.3
16.9
109.7 2150 64.4
43.3
0.67
84.4
5.87
11.0
401.3
141.7
20.9
6.5
128.7 1900 59.3
38.9
0.66
81.8
6.58
9.0
499.7
140.4
26.3
2.5
9.0
2.5
5.7
129.1 2150 59.3
39.9
0.67
83.2
6.99
8.5
503.3
144.1
26.6
4.2
122.3 1900 59.7
39.3
0.66
80.8
6.19
9.6
459.2
140.2
21.4
2.9
13.5
4.8
11.2
110
122.6 2150 59.7
40.3
0.68
82.2
6.58
9.1
462.4
143.9
21.6
4.6
119.2 1900 60.0
40.1
0.67
80.7
6.07
9.9
446.1
140.1
19.8
4.7
18.0
7.2
16.6
119.4 2150 60.0
41.1
0.69
82.0
6.46
9.3
449.2
143.7
20.0
6.6
Cooling data based on 80/67 °F EAT. See Correction Factors at end of section for different conditions
LWT is based on 15% (by volume) methanol antifreeze solution only or 485 multiplier
Performance data accurate within ± 10%
Discharge pressure is ± 20 PSI; Suction pressure is ± 10 PSI
SubCooling is ± 5 °F; Superheat is ± 6 °F
EWT
°F
Flow
GPM
WPD
XT Models, Rev.: A
67
Enertech Global
Greenville, IL - Mitchell, SD
info@enertechgeo.com
MEMBER
Rev Tab
Enertech Global is continually working to improve its products. As a result, the price, design and specifications of each product
may change without notice and may not be as described herein. For the most up-to-date information, please visit our website,
or contact our Customer Service department at info@enertechgeo.com. Statements and other information contained herein are
not express warranties and do not form the basis of any bargain between the parties, but are merely Enertech Global’s opinion
or commendation of its products.
20D082-01NN
Enertech Global, LLC
Rev.: A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising