Каталог был представлен на выставке

Каталог был представлен на выставке
1205898
Passionate About Sound
FULL LINE CATALOG 2009 | 2010
The Art of Audio
Sound is at its best when the sound system
reproduces the source with nuance, power
and accuracy allowing the listeners to hear the
performance without even being conscious of
the processors, amplifiers and loudspeakers.
It doesn't matter if you're the performer on
stage, the dancer on the floor, the listener in
the audience or the passenger being paged
at the airport - QSC is passionate about the
sound you hear.
This edition of the QSC catalog includes
many QSC products that have proven their
value, quality and reliability on the road and
in permanent installations. But you will also
see a number of new products that tightly
integrate digital signal processing, power
amplification and loudspeaker technologies
into systems with performance that far
exceeds the sum of their parts.
There's more to it than the products, the
systems and the science of it all. There's also
the quality, service and commitment that QSC
is known for. If you share our passion, we're
sure that you'll enjoy learning about, installing
and hearing our products as much as we
enjoyed creating them.
i
CONTENTS
4
14
24
2
Amplifiers
GX Series
•I
RMX Series
PLX2 Series
'>
(.
PowerLight™ 3 Series
/
CX Series
8
ISA Series
ч
Amplifier Overview
10
Amplifier Accessories
12
Digital | Network
Q-Sysm
14
QSControl.net™ BASIS™ | RAVE | DSP
18
NAC-100 Network Audio Controller
20
SC28 System Controller
21
DSP-3 | DSP-4 I DSP-30
22
Loudspeakers
CSM Series Concert Stage Monitors
24
WideLine-10 Line Array System
26
WideLine-10 Subwoofers
28
WideLine-8 Line Array System
30
WideLine-8 Subwoofers
32
Networked Concert System Solutions
34
WLWX Weatherized WideLine™
35
ILA Series Installation Line Array
36
AcousticDesign™ Ceiling Loudspeakers
38
AcousticDesign™ Loudspeakers
40
AcousticDesign™ Subwoofer
42
Distributed System Solutions
l >
К Series Active Loudspeakers
44
HPR Series Powered Loudspeakers
46
ISIS Series Loudspeakers
48
I
••чНигЯК
V^.
' 'jdfl^^^l
til Li
>
s
w
,
l
f
0 «i > w
0
CM i
•-**•v
nmm
.»-„»
IMM
'WSSSKSSB? мтшивиип •
JBI* f
E С
зйГ) 1
-™
«пишите Ч^_^.._
С
(
д
C3SCZ
"SBff I
-SIP
\e^ \ . ^ * 1 ц IT1TI f
•nSuS*
ИГГГ»
GX5
GX Series
Entertainers I Musicians I DJs
The GX Series amplifiers offer maximum performance,
portability and reliability for sound system owners on a
limited budget, perfectly suited for use by entertainers,
musicians and DJs. The two GX Series amplifiers are
uniquely designed to supply optimal power to the
sound reinforcement loudspeakers most often used
by entertainment professionals. The GX3 is ideal for
speakers in the 300 watt (Program) range, while the
GX5 provides full performance for 500 watt (Program)
speakers. Both models supply maximum possible
power to 4П and 80. loads.
The use of subwoofers is supported with a crossover
switch and front panel gain controls that allow easy
access for balancing the sub with the full-range cabinet.
GuardRail™ optimizes peak power to the two channels
individually and its protection keeps the system
working during demanding sets. With dramatic styling,
easy hookup, flawless operation and protective circuitry,
professional entertainers now have an amplifier that is
designed for their specific application.
CX Series
Watts per channel
Power levels matched to the most popular speakers used
by entertainers.
Optimized for maximum real-world headroom into 4П
and 8П speaker systems.
Inputs: XLR, 1/4" TRS and phono input connectors for
compatibility with any source.
Outputs: Speakon® combo accepts, 1/4" (TS) plugs or
Speakon 2-pole and 4-pole plugs (connects 2 poles only).
Binding posts support all other speaker wiring systems.
Minimum depth chassis (10.1 "/257 mm) fits in compact,
inexpensive effects racks.
Lightweight - less than 28 lb (12.6 kg).
Detented gain controls for precise setting and matching
of sensitivity.
GuardRail™ automatically protects the amplifier and
loudspeakers from damage due to temperature rise or
overdrive without shutting down the show.
Model
8П
40
GX3
300
425
Front panel LEDs monitor Power, Signal and Clipping.
GX5
500
700
Subwoofer/Satellite crossover built-in.
Both channels driven.
1 kHz, onset of dipping.
I
i
lllllllllllllllllllllllllllllllll
RMX 2RU Models
RMX Series
Entertainers | Musicians | DJs
Concert Systems
The RMX Series is a proven line of amplifiers
combining legendary QSC reliability, audio perfor­
mance and affordability. Entertainers and touring
users have made RMX one of the leading amplifier
series in the world. For mid-power applications, the
2RU models offer 40 power ratings from 300 to 750
watts per channel. For premium loudspeaker systems
with extremely high power capacity the 3RU models
(RMX4050HD and RMX5050) are unchallenged.
•
Independent, defeatable clip limiters reduce distortion and
protect speakers.
•
Selectable low-frequency filters (30 or 50 Hz) protect
speakers and increase headroom.
• High-current toroidal transformers yield higher power and
less noise for 20 operation.
•
Front panel LED status indicators enable system
monitoring and troubleshooting.
•
Extensive protection circuitry and thermal protection
ensure long-term reliability.
Connectors: Input - XLR and 1/4" TRS.
Outputs - Speakon®, binding post.
•
RMX
RMX Series
Watts per channel
Stereo
Bridged
Model
8Г1
40.
20'
40'
RMX850
200
500
430
830
RMX1450
280
450
700
1400
RMX1850HD 360
600
900
1800
RMX2450
750
1200
2400
RMX4050HD 850
1400 2000
4000
RMX5050
1800 2500
5000
500
1100
/ kHz, 0.1% THD *; kHz, 1% THD
PLX2 "02" Models
PLX2 Series
Entertainers | Musicians | DJs
Concert Systems
The PLX2 Series are powerful, lightweight amplifiers
designed to meet the rigorous demands of live
musicians, mobile entertainers, and portable PAs.
Featuring third generation PowerLight™ technology,
the PLX2 Series delivers superb overall audio quality
with especially powerful low-frequency performance.
The PLX2 Series amps have a professional, attractive
appearance, with a die-cast aluminum front panel
acting as an integral I-beam, to create an extremely
rugged, road-worthy device.
PLX2 consists of two series. The "02" models (1802,
2502, 3102, 3602) can drive 2П loads and include
subwoofer filtering and other signal processing ameni­
ties. For applications that do not require bridging, 2fi
operation, or internal subwoofer signal processing, the
"04" models (1104, 1804) deliver the same audio
performance as the "02" models in a lighter-weight,
more cost-effective unit.
•
Front panel LED status indicators enable system
monitoring and troubleshooting.
•
Front panel gain controls (1 dB detents) allow precise
input sensitivity adjustment.
•
Speakon® NL-4 output connectors provide a positivelocking speaker connection. Channel 1 's output can use
all four wires to connect to bi-amplified speakers with a
single cable.
•
Balanced XLR and TRS parallel inputs accommodate the
most commonly used input connectors for live sound and
support loop-through routing.
• Active Inrush Limiting prevents AC mains circuit breakers
from popping during turn-on.
The "04" models (PLX1104 and PLX1804) offer
advanced PLX2 technology with less weight, less
chassis depth and even greater value for users who
don't require 20 or bridged operation.
PLX2 "04" Models
PLX2 Series
Watts per channel
Stereo
Bridged
Model
80-
40-
2П"
PLX1104
325
550
PLX1804
600
900
-
PLX1802
330
575
900
1800
PLX2502
450
750
1250
2500
PLX3102
600
1000
1550
3100
PLX3602
775
1250
1800
3600
40"
-
*/ kHz. 0.1% THD, both channels driven
"I kHz, 1% THD, both channels driven
То prevent unauthorized
adjustment of input
attenuation settings, a
security lockout plate
is included with every
PowerLight 3 amplifier.
чфь +
PL380 output device
(left) compared with
typical output devices.
PowerLight™ 3 Series
Concert Systems
Installed Sound
The PowerLight 3 Series are Pat Quilter's "Ultimate
Analog" amplifiers, designed for the most demanding
concert and live-sound reinforcement applications. All
three models use our latest generation PowerLighV"
technology - the world's most efficient power supply.
The 8000 watt Class D PL380 shares a clean, efficient
control, connector and indicator layout with the Class H
PL340 (4000 watts) and PL325 (2500 watts).
All PowerLight 3 Series amplifiers have zero signal
latency, for seamless integration with existing equip­
ment and flawless loudspeaker alignment. The flexible
PowerLight 3 Series architecture provides users the
choice of comprehensive, networked remote control,
monitoring and DSP or the cost savings of a simple,
straightforward analog input configuration.
The PL380 amplifier now includes a detachable
power cord featuring 32 amp PowerCon«
connectors from Neutrik.™
PowerCon connectors are a robust and reliable AC
cable connector with high current capacity (32 amps)
designed expressly to meet the needs of high-power
distribution systems. An inherent part of the PowerCon
design, the connector facilitates fast and easy locking,
protecting against unintentional disconnects.
PL380 plug types remain unchanged, with the existing
NEMA L5-30P plug found on all 120V and 100V
PowerLight PL380 amplifiers, and a "Shuko" CEE 7/7
16 amp Continental European plug still in place on
the 230V PL380. All PowerLight PL325 and PL340
amplifiers will retain their existing 20 amp PowerCon
connectors and plug types.
r
к
• m—~~ 1 -.T ! -ВШИ!"" c«i
R A W U I Ш И Ш
|'
OSC
Tin ' ''
i^mn
Ci
JM
i
k' :v ''«^y
1 .
^
•»••.
^H^H
PL380
PL325 and PL340
New 32 A PowerCon on PL380
A three-position Input Sensitivity switch makes it easy to
integrate PowerLight 3 Series amplifiers into existing amp
racks and power systems.
Zero signal latency processing is standard on all
PowerLight 3 amplifiers, with either the DSP-4 rear
panel module, Q-Sys™ or QSControl.net™ BASIS™ units.
SC28 or other loudspeaker management processors
can also be used.
XLR, Euroblock and DataPort connectors simplify
signal connections, allowing multiple options for
loop-through wiring.
Comprehensive internal protection is designed to protect
amplifiers and speakers against over-current, excessive
AC voltage, over-temperature and clipping - all without
compromising the integrity of normal program signals.
Watts per channel
PL3 Series
Model
80
40
2П
PI S25
500
850
1250
PL340
800
1250
2000
PI Wl)
1500 2500
4000-
El A 1 kHz, J% THD
'PowerCon and Neutrik are trademarks of Neutrik.
•••--F "
> •
*Burst mode testing
required due to AC
service current limitations
CX Series
Installed Sound
CX 2-channel Models
The CX Series is a range of two, four and eight
channel amplifiers designed for installations requiring
premium sound quality and high output power.
Recognized by sound contractors worldwide as the
standard for reliability, the 2RU CX Series features
PowerLight™ power supply technology which reduces
weight while also improving audio quality and elimi­
nating AC mains hum. The PowerLight supply also
results in very high efficiency so CX amplifiers draw
less power and produce less heat for savings on
energy and air conditioning.
• Active Inrush Limiting brings the amplifiers on line gently,
eliminating the need for costly AC power sequencers.
•
Front-panel gain controls withl dB detents allow precise
level adjustment and are protected by tamper-proof
security covers.
•
DataPort connects directly to QSC accessories and
digital signal processors for extensive remote control
and monitoring of amplifier functions via Q-Sys™ and
QSControl.net.™
•
Selectable clip limiters and infra-sonic filters protect
loudspeakers from damage due to distortion and
overexcursion.
• Transformerless 70 volt and low-impedance models
are available.
• Connectors: Input - XLR/F and 3-pin Euro-style.
Output - barrier strip.
CX 4-channel Models
( X :;, 51.иiiii• I Mo.Iris
Watts per channel
CX Series
2-Ch Models 70 V
80
40
70'
-
CX302V
250
-
CX602V
440
550
-
CXI 202 V
1000
700
1100
-
200
325
600
500
500
800
42b
700
1200
СХ302
CX502
CX702
CX902
440
550
900
1500
CXI 102
1000
700
1100
1700
4-Ch Models /(IV
80
40
20"
CX204V
220
-
-
-
CX254
-
170
250
CX404
250
8-Ch Models 70 V/, 80
CXI 08V
100
-
CXI 68
-
90
400f
4DS
130
450
-
All channels driven.
20 Hi - 20 kHz, 0.05% THD
V kHz, 0.05% THD
**/ kHz, 1%THD
tl kHz, 0.1% THD
Ш0 Hz - 20 kHz, 0.2% THD
§20 Hz - 20 kHz, 0.1% THD
" Г
л
ИГ
li• «иa K l:
nif
SI
•
•J
m I-.
J
—
•
a
ISA Series
I
Ш^ . ' v -
II
IMX
0
•
,,
ISA Series
Installed Sound
ISA amplifiers are ideal for installations where the
budget is tight but reliability and sonic performance
can't be compromised. The 3RU ISA Series offers
models capable of driving 20 loads and models with
selectable 25, 70 and 100 volt outputs. 'Ti" versions
will drive a distributed and a 40 or 80 system
simultaneously from the same channel.
•
•
'Oil Mil'
Watts per :hannel
70 V
8Q"
4П"
20f
-
IB5
280
430
260
425
700
450
650
1200
ISA1 550
1500/
800
1 500
2000
ISA300Ti
300
185
280
430
ISA500Ti
500
260
425
700
ISA800Ti
800
450
650
1200
ISA450
ТШГ ISA750
"50Hz- 16kHz. 0.5% WD
"20Hz-20kHz,0.l%THD
f/ kHz, 1% THD
tfDirea Output, 70V, less than 0.1%
•
Rear-mounted gain controls with 2 dB detents provide
repeatable settings.
•
Independent, defeatable clip limiters reduce distortion
and protect speakers.
•
Selectable high-pass filters protect against transformer
saturation and driver overexcursion.
•
Includes extensive DC, infrasonic, thermal overload, and
short circuit protection.
•
DataPort V2 is included for connection of
DPV2-compatible signal processing accessories.
(XC-3, LF-3 and SF-3.)
•
Connectors: Input - XLR/F and 3-pin Euro-style.
Output - barrier strip.
THD, 20 Hz - 20 kHz, +0/-O.3 dB
Amplifier Overview
Watts per channel
CX SERIES
Channels
70 V
80
40
20
Bridged
RU
Net Weight / Shipping
GX3
2
300
425
2
27 lb (12.1 kg)/31 lb (14.1 kg)
CX5
2
500
/00
2
28 lb (12.6 kg)/32 lb (14.6 kg)
RMX850
2
200
Kill
430
830
2
35 lb (15.9 kg)/41 lb (18.6 kg)
RMX1450
2
280
450
700
1400
2
40 lb (18.2 kg)/46 lb (20.9 kg)
RMX1850HD
2
360
600
900
1800
2
И'.ЬипЛ,;), ,n.', lb!.", liy
RMX2450
a
-
500
750
1200
2400
2
44.5 lb (20.2 kg) / 50.5 lb (23 kg)
RMX4050HD
2
-
!N)
1400
•IIIHI
.IDini
3
68 lb (30.8 kg) / 77 lb (34.9 kg)
RMX5050
2
-
HID
1800
Ml;
4)00
3
75 lb (33.1 kg) / 87 lb (37.2 kg)
PLX1104
2
-
325
SSI)
-
-
2
13 lb (5.9 kg)/18 lb (8.2 kg)
PLX1804
2
-
hill)
-
-
.'
13 lb (5.9 kg)/18 lb (8.2 kg)
PLX1802
?
-
'i',0
',/',
41,1)
1800
,'
21 lb (9.5 kg)/26 lb (11.8 kg)
PLX2502
2
-
• IM)
750
1250
2500
2
21 lb (9.5 kg)/26 lb (11.8 kg)
PLX3102
2
-
600
ООП
1550
i l l И)
.'
21 lb (9.5 kg)/26 lb (11.8 kg)
PLX3602
2
775
1250
1800
3600
2
21 lb (9.5 kg)/26 lb (11.8 kg)
RMX SERIES
PLX2 SERIES
Watts per channel
PLJ SERIES
Channels
70 V
80
40
20
Bridged
RU
Net Weight / Shipping
2500
2
22 lb (10 kg)/31.5 lb (14.3 kg)
2
22 lb (10 kg)/ 31.5 lb (14.3 kg)
8000
2
241b (11 kg)/33.5 lb (15.2 kg)
41!
2
21 lb (9.5 k g ) / 2 7 lb (12.3 kg)
PL325
>
-
Mil)
B50
I'M!
PL340
1
-
BOO
1250
2000
PL380
2
1500
2500
4000
i
CX SERIES
CX302
1
-
200
S25
„in
CX502
7
-
,IIII
Mill
BOO
1600
2
21 lb (9.5 k g ) / 2 7 lb (12.3 kg)
CX702
.'
-
425
700
1200
2400
.»
21 lb (9.5 k g ) / 2 7 lb (12.3 kg)
CX902
>
440
550
Hill
1500
3000
.'
21 lb (9.5 k g ) / 2 7 lb (12.3 kg)
CXI 102
2
1000
/пи
linn
1700
3400
l
2 l i b (9.5 k g ) / 2 7 lb (12.3 kg)
CX302V
2
250
2
21 lb (9.5 kg)/27 lb (12.3 kg)
«602V
2
440
550
2
21 lb (9.5 kg)/27 lb (12.3 kg)
CX1202V
2
1000
700
1100
2
21 lb (9.5 kg)/27 lb (12.3 kg)
CX254
4
170
250
2
21 lb (9.5 kg)/27 lb (12.3 kg)
CX4Q4
4
250
mil
2
21 lb (9.5 kg)/27 lb (123 kg)
CX204V
4
2
21 lb (9.5 kg)/27 lb (12.3 kg)
0(168
8
2
21 lb (9.5 kg)/27 lb (12.3 kg)
CXI08V
8
2
2 l i b (9.5 kg)/27 lb (12.3 kg)
S
36 lb (16.3 k g ) / 4 2 lb (19.1 kg)
42 lb (19 kg) / 4 8 lb (22.0 kg)
450
900
200
90
130
100
ISA SERIES
ISA280
1
-
185
280
CO
M-,1,1
I5A450
I
-
!6Q
-I?1,
700
1400
i
ISA750
2
450
650
1200
2400
3
47 lb (21.3 kg) / 53 lb (24.0 kg)
ISA1350
2
800
1300
2000
4000
3
68 lb (30.8 kg) / 77 lb (34.4 kg)
ISA300Ti
I.
100
185
280
430
BSO
•:
44 lb (20.0 kg) / 50 lb (22.7 kg)
ISA500H
2
'
260
425
700
linn
i
49 lb (22.3 kg) / 55 lb (25 kg)
ISA8OOT1
2
".III!
(Ml
650
'(«
2400
1
57 lb (26 kg) / 63 lb (28.6 kg)
Amplifier Accessories
XC-3 2-way Crossover
LF-3 Low-Frequency Filter
The XC-3 is an active, 2-way
crossover module that mounts to
the rear panel DataPort of
2-channel QSC amps (DCA,
PL2, PL3, CX, ISA).
The LF-3 low-frequency filter,
when used with the XC-3 2-way
crossover, provides a 3-way active
crossover system. The LF-3
mounts to the rear panel of
2-channel QSC amps (DCA, PL2,
PL3, CX, ISA) to conserve cost and rack space. The
LF-3 is comprised of two discrete channels with 4th
order Linkwitz-Riley low-pass filters (24 dB/octave
slope). Each channel has a delay to time-align low-,
mid-, and high-frequency speakers, and a trim control
(0-20 dB of attenuation) to match levels. One ampmounted LF-3 supports up to two other amps (even
in stereo) with XC-3 accessories installed.
The XC-3 features 4th order Linkwitz-Riley filters (24
dB/octave) with the low frequencies routed to amp
channel 1 and the highs to channel 2. Each channel
has an all-pass filter delay for time alignment of lowand high-frequency drivers, and a trim control (0-20
dB attenuation) to balance the frequency bands. The
high-frequency channel offers up to 10 dB of boost at
20 kHz to compensate for cinema screen loss or to
properly equalize constant-directivity horns. A 3-way
crossover can be implemented using the XC-3's lowfrequency high-pass filter with the LF-3.
SF-3 Subwoofer Filter
The SF-3 subwoofer filter
provides subwoofer signal
processing without the need for
a conventional crossover. The
unit mounts to the rear panel
DataPort of 2-channel QSC amps
(DCA, PL2, PL3, CX, ISA) to conserve cost and rack
space. A 4th order Linkwitz-Riley low-pass filter may be
set to 80, 150 or 250 Hz. The subsonic filter offers
roll-off frequencies in the range 20-50 Hz to prevent
driver overexcursion. An optional EQ is provided to
extend the response of B6 speaker enclosures and is
especially useful for cinema applications including the
QSC SB-5218 and SB-7218 subwoofers. A trim
control (0-20 dB of attenuation) allows balancing the
various frequency bands.
s5^ *
DataPort
The QSC DataPort provides a simple, convenient means of
connecting and powering digital and analog accessory devices
to expand the capabilities of QSC CX, DCA, PowerLight™,
PowerLight 2 and PowerLight 3 amplifiers. Devices supported
include the DSP-3, DSP-4, XC-3, LF-3 and SF-3. Note that ISA
models require an external power adapter for the DSP devices,
and PL380 for the DSP-3 device.
In addition, the DataPort HD15 connector provides a singlecable interface to Q-Sys™ and QSControl.net™. Q-Sys and
QSControl.net allow remote amplifier monitoring and control.
This functionality is supported by CX, DCA, PowerLight,
PowerLight 2 and PowerLight 3 amplifiers.
Please see the specifications for the specific accessory devices
and amplifiers before planning a system.
i.'
OT-300a Output Autoformer
The OT-300a is a robust step-up autoformer accessory
that adapts power amplifier outputs (maximum voltage
range 17-35 volts) to drive a 70 volt distributed line with
up to 300 watts. Four voltage taps can be selected to
match the output voltage of your amplifier. Conversely,
the OT-300a can be used as a high-power speaker trans­
former, driving speakers with up to 300 watts from a 70
volt distributed line. The OT-300a is compatible with any
amplifier rated at up to 350 watts at 4П.
OT-600 Output Autoformer
The OT-600 is a robust step-up autoformer accessory
that adapts power amplifier outputs (maximum
voltage range 40-50 volts) to drive a 70 volt distrib­
uted line with up to 600 watts. Three voltage taps can
be selected to match the output voltage of your amp.
The OT-600 can also drive a 100 volt line when used
with an amp with a maximum output voltage in the
range 55-70 volts. Conversely, the OT-600 can be
used as a high-power speaker transformer, driving
speakers with up to 600 watts from a 70 volt distrib­
uted line. The OT-600 is compatible with amps rated
between 350 and 650 watts at 4П.
IT-42 Output Isolation Transformer
The IT-42 is an output isolation transformer accessory
for the QSC CX302 amplifier, allowing it to drive two
25, 70 and 100 volt distributed lines in stereo or
parallel or a single 140 or 200 volt line in bridged
mono. The IT-42 is pre wired for quick and convenient
mounting to the back of the CX302 amplifier and
requires no additional rack space.
All the accessories listed are RoHS compliant.
LSifll
и
;
4t»t U
Jg*^ J
«Ш> Q - S Y S
The world's most complete integrated system solution.
Q-Sys™
Integrated System Platform
Q-Sys is a complete integrated system platform that
encompasses everything from the audio input to
loudspeakers. Q-Sys provides all the audio routing,
processing, control and monitoring necessary for any
facility while maintaining the audio quality and reli­
ability QSC has come to be known for. Designed
specifically for the rigorous requirements of large-scale
applications, the power of Q-Sys is a logical choice
for stadiums and arenas, attractions and theme parks,
performing arts venues, transportation hubs, legislative
and judicial chambers, hotels and casinos, houses of
worship, corporate campuses, educational facilities or
anywhere the need exists for a powerful system-wide
audio solution.
Components
The primary elements of a Q-Sys system are the Core
and I/O Frame. The Core is the brain of the system;
14
it performs all the audio routing and processing and
handles all control functions. The Q-Sys Core is avail­
able in three sizes, Core 1000, 3000, and 4000, and
features a centralized processing architecture. Having
all processing take place in one unit gives the designer
complete flexibility while enabling simplified system
redundancy. With a centralized architecture any input
can be routed to any output without convoluted
signal paths.
Although Q-Sys employs a centralized structure, it
retains the ability to physically locate the input and
output connections near their sources and destinations
using I/O Frames. Each I/O Frame can house up to
four I/O cards enabling up to 16 channels of input
and/or output in a single unit. Available cards include:
a 4-input standard and a 4-input premium-quality
mic/line input card, 4-channel line output card, an
AES card with 4-channels of input and output, and a
4-channel card for connection to QSC DataPort ampli­
fiers. Additional cards will be added so check the QSC
website for the latest information.
QSC DataPort
Amplifiers
QSC
Loudspeakers
QSC DataPort
Amplifiers
QSC
Loudspeakers
Redundancy
Network
QSC products are renowned for reliability. But sometimes, redundancy is a requirement. Q-Sys supports
multiple levels of redundancy.
Q-Sys relies on Q-LAN, a proprietary, standardsbased, low-latency Gigabit Ethernet network
implementation. Q-LAN is responsible for audio
routing between devices and ensures that all signals
are transmitted from source to destination in less
than 1/3 of a millisecond. Q-Sys combines Q-LAN
with audiophile quality, 32-bit floating point distribution and high performance A/D and D/A converters
resulting in outstanding fidelity and a total system
latency - any input to any output with up to 10
network switch hops - of less than 2.5 milliseconds.
In addition to low latency distribution, Q-Sys also
supports long-haul IP streaming of audio over Wide
Area Networks (WAN) as well as auto-discovery and
configuration of end nodes.
•
Network Redundancy may be implemented by simply
adding additional network switches and cabling. In the
event of a network failure, the Q-Sys components switch
over instantly to the back-up network.
•
Core redundancy allows a second core to be connected
to the network. Should the primary core fail, the
secondary core takes over.
•
I/O Frame redundancy gives the designer the option of
adding redundant I/O Frames for high-priority areas.
•
Amplifier redundancy is also possible with the use of
the QSC DAB-801 (DataPort Amplifier Backup panel).
This accessory connects to the inputs and outputs of
five QSC DataPort amplifiers with one amp serving as
a backup for the other four (4 + 1 redundancy, using
2-channel amplifiers). A second DAB-801 may be added
for 8 + 1 redundancy.
15
43Ш»
Q-Sys™ employs a 64-bit processing engine, low latency 32-bit
floating point distribution, and high performance A/D and D/A
converters to provide outstanding audiophile quality.
Swlen» Unmulcd Bcommuniubont OX (10.10.9JOt-
Design and Set-Up
The system design environment was created specifi­
cally to be intuitive and easy to use. It is laid out
without clutter or complicated, multi-level menus.
You'll be able to apply your skills to designing the
system - not figuring out the software. Q-Sys also
saves time during system set-up and commissioning.
While many existing systems are agonizingly slow to
assemble a new configuration, Q-Sys designs can be
compiled and deployed in seconds. Once the system
is designed, you will find Q-Sys a useful suite of
troubleshooting and measurement tools. A test probe
provides an RTA display of the signal at any point in
the design. FFT-based real-time analysis and impulse
response are also provided for on-site acoustical
measurements. All you need to bring is a measure­
ment microphone.
Processing
One of the primary development goals was to create
a platform that had nearly unlimited resources,
and Q-Sys truly lives up to that goal with unrivalled
processing breadth and depth. In the Q-Sys Cores
the internal processing is 64-bit providing incredible
ii.
headroom and ensuring high performance. Even in
the smallest Core, the Core 1000, there are tremen­
dous DSP resources. As an example, most processing
functions are capable of providing up to 256 chan­
nels simultaneously and mixers can provide up to
512 input and output channels. In addition to huge
processing capacity Q-Sys offers an extensive selection
of processing and control functions.
r""^
f
*
ШШШ
-*"
f
»
. « .
m
T^\ ' ш ш
.
»
tT++++ttt+++
b-,-1"*.,
Take a Q-Sys™ tour and download a free copy of
the Q-Sys™ Designer software at qscaudio.com
.
•
.
»
»
With a robust centralized architecture, Q-Sys™ offers exceptional
design flexibility while enabling simplified system redundancy.
ГС'-.-Л РГ'.Л Г~УП Г-_лП
I !г*ч I I l-:ti:t1 [j-B:t1 ГГл-.Л
oil'
k>
ci,
JP
""
<€Z> <:
ГТП
UC Mill П И К И LLC, t«t« MM. U >»»
Control
Integration
In addition to its powerful processing capabilities,
Q-Sys provides extensive levels of system control
which can be as simple or sophisticated as the
application requires. Nearly every audio processing
parameter can be a command source or destina­
tion, as can switch closures or potentiometers
via the on-board GPIO (General Purpose I/O).
Control specific operators like the Boolean Logic or
Arithmetic functions can then be utilized to enhance
the management capabilities based on operator or
system control input. Additionally, Snapshots of any
or all functions can be created and recalled using the
snapshot tool.
Of course, Q-Sys can be used with any amplifiers or
loudspeakers, but the system's power increases expo­
nentially when integrated with QSC loudspeakers and
DataPort amplifiers. Using the DataPort output card in
conjunction with PowerLight™, PL2, PL3, СХ, or DCA
amplifiers enables complete end-to-end system-level
telemetry and supervision. Adding QSC loudspeakers
to the mix opens opportunities for greater control
and system reliability by enabling functions such as
driver excursion limiting and speaker fault detection.
For example, bringing a QSC line array powered by
QSC amplifiers into the design and connecting via
a DataPort card will automatically invoke the proper
Intrinsic Correction™ tuning optimizing its acoustic
performance. Simply set the properties for the number
of speakers and the coverage angle of the array and
Q-Sys handles the rest.
When a richer user interface is needed, control panels
with a custom look and feel are easily created using
the Custom Control Interface tool. These panels can
be designed by pulling elements directly from the
schematic allowing pre-defined end-user control
from panels that can be viewed and operated from
a network computer or other web-capable devices.
IP-based external control protocol ensures that Q-Sys
can connect with 3rd party controllers for truly limitless
control capabilities.
Q-Sys™ is the Solution
Q-Sys is a complete routing, processing and control
solution. While it may be possible to create systems
by combining products from other manufacturers,
Q-Sys provides this capability in an elegant hardware/
software platform from a single supplier ensuring that
the integration process goes smoothly and operation
is flawless. It is fast, incredibly powerful, reliable, and
features rock-solid performance backed by the unri­
valed service and support QSC has built its reputation
on. If you are designing a theme park or attraction,
airport or transportation hub, hotel, casino, conven­
tion center, sports facility, church, educational campus,
legislative or judicial chamber, theater, or corporate
facility, Q-Sys is for you.
This is an example of a custom control panel created
using the Q-Sys Custom Control Interface tool. Once
created, these panels may be served up on a variety of
web-enabled controllers, touch screens and computers.
I/
*1
QSControl.net M Version 3
BASIS™ I RAVE DSP
Networked control, transport, processing and
monitoring — from source to loudspeaker
stadiums, arenas, theatres, nightclubs, restaurants,
hotels, houses of worship, corporate campuses and
educational facilities, as well as large scale touring
concert systems.
Integrated Technologies
QSControl.net is a versatile foundation for networked
audio systems that extend from microphone and other
inputs to loudspeakers and similar outputs. QSC
designed this proprietary technology expressly for
system integrators, contractors, consultants and
concert audio engineers who need to integrate signal
processing, amplifier management and audio transport
functions with QSC power amplifiers and loudspeakers.
The powerful BASIS hardware platform integrates
control, monitoring, protection and processing of
amplifiers and loudspeakers with configurable DSP
and CobraNet™ digital audio transport via Ethernet:
BASIS products are the core of the QSControl.net
enabled products. QSCs RAVE units, which combine
DSP functions with CobraNet digital audio transport,
and the DSP 322ua dedicated signal processor are
also integral to QSControl.net systems. BASIS, RAVE
and DSP units are all programmed and controlled via
QSCs Venue Manager software.
Far more than digital signal transport and processing,
QSControl.net integrates the entire audio system CX, PL2, PL3 and DCA series amplifiers as well as a
growing range of loudspeaker systems including
AcousticDesign™, WideLine™, I LA, ModularDesign™
and DCS products. Ideally suited for applications both
large and small, the power of QSControl.net is the
logical choice anywhere a need exists for a complete
system-wide audio solution - installations such as
QSControl.net combines three distinct QSC technologies of configurable DSP, amplifier/loudspeaker control
and monitoring, and CobraNet audio transport into
a single unified system. As noted earlier, various
QSControl.net hardware devices (BASIS, RAVE and the
DSP 322ua) include functionally appropriate elements
of all these technologies.
All of the technologies and devices found within the
QSControl.net platform can be programmed and
controlled from a single networked computer or simultaneously from multiple networked computers. Armed
with wireless laptops, multiple operators can even
make adjustments to different parts of a QSControl.net
system concurrently and in real-time. The new NAC-100
wall controller gives customers quick and easy access
to pre-defined functions and configurations.
QSCreator Custom Control Panels
QSCreator is hosted inside our Venue Manager system
set up software to facilitate custom control panel
creations. Control panels with a custom look and feel
are designed by selecting from an extensive library of
faders, knobs, buttons, meters, indicators and graphic
tools. Once a control screen design has been developed, QSCreator can be established as the only software
required for system operations. This prevents accidental
adjustments or unauthorized tampering while keeping
the control template as easy-to-use as possible.
BASIS™ I RAVE I DSP
•
Routers
Powerful,
Programmable
Processing
•
The QSControl.net platform
provides an extensive set
of processing functions,
including:
Can accommodate any
combination of inputs and
outputs up to 24 x 24.
Cain Controls
•
Can accommodate any
channel count up to 24.
Matrix Mixers
Graphic Equalizers
•
•
Two Octave ISO
Duckers
•
One Octave ISO
•
Up to 24 Inputs and
Outputs.
•
Two-Third ISO
•
One-Third ISO
•
Facilitates any number of
inputs up to 22.
•
•
Direct outputs available for
every input.
Custom (choose number of
bands, start frequency and
end frequency).
•
A unique Program
Reference Input auto­
matically attenuates the
selected input whenever
•
Pink noise
Filters
•
White noise
•
program materia] is sensed '
•
Sine generator
BASIS 722az
Analog
The CM 16a Amplifier Network
Monitor provides sixteen chan­
nels of audio level control,
monitoring, and amplifier
management for DataPortequipped QSC amplifiers.
Control and monitor data is
communicated between the
System Controller computer
and CM 16a over an Ethernet
network. The CM 16a, located
in the amplifier rack, is linked to
amplifiers via DataPort cables.
Noise Generators
Crossovers
•
Linkwitz-Riley
•
Butterworth
•
Bessel-Thomson in-phase
Delays
•
Bessel-Thomson
symmetrical
•
Up to 910 milliseconds.
•
Units measured in time,
meters, feet.
•
2-way, 3-way and 4-way
general purpose adjustable.
CM 16a devices can be
controlled and monitored using
Venue Manager software. Some
features of Venue Manager may
not be applicable to the CM 16a,
such as QSCreator screens,
global presets and masters.
While the CM 16a is not as
feature-rich as the BASIS, RAVE
and DSP products listed in the
chart, it does have a viable use
in systems which already have
pre-processed audio.
High-pass, low-pass, allpass, shelf, parametric,
parametric shelf,
Butterworth high and lowpass, Bessel-Thomson high
and low-pass.
Macros
Dynamics
•
Compressor
•
Peak limiter
•
•
Dynamics processor
•
Noise gate
User-definable custom
blocks with password
protection.
Inputs
Model
Network Amplifier
Control and Monitoring
Up to eight channels of
audio can be "ducked"
simultaneously. Fade-in
and fade-out times can be
up to 60 seconds each.
The priority channel can
also be part of the ducker's
output mix.
Cain Sharing Automixing
*This latter feature is
especially useful for
applications using several
microphones, an automixer
and multiple sources of
program material (e.g.,
CD, DVD, etc.). With
the Program Reference
Input, the volume of the
microphones can be
automatically attenuated
to keep the other sources
from bleeding into
the system.
CM 16a
Automatic Cain Control —
automatically boosts belowthreshold signal levels up
to a user-defined target
output level and reduces
above-threshold signal
levels down to a userdefined target output level.
Music, speech and custom
operating modes.
Digital
Outputs
CobraNet
Aiidlnj:
8 line level
DataPort
I IIIJMNI'I
Monitor I/O
YES
4 (8 channels)
BASIS 902zz
24 of 32
i (8 channels)
S2
YES
BASIS 904ZZ
24 of 32
8 (16 channels)
v
Y! S
16 of 32
8 (16 channels)
S2
16of32
4 (8 channels)
32
YES
if, oi 52
4 (8 channels)
32
YES
YES
BASIS 9141;
1 XI R line Itrvfl
BASIS 922az
8 line level
BASIS 922dz
25 pin AES/EBU
(8 channels)
BASIS 922uz
8 universal
-
16 of 32
-
4 (8 channels)
32
-
-
8 line level
-
-
-
16 ol 52
-
16 ol 52
16 of 32
mic/line
DSP 322ua
8 universal
mic/line
RAVE S20UZ
8 universal
32
-
8 line level
52
8 line level
32
-
•
mic/line
RAVE 522aa
8 line level
RAVE S22ua
8 universal
•
mic/line
"ГГПГ
I'l
QSControl.net™ NAC-100
Network Audio Controller
This fully networked wall controller adds a new
dimension of versatility to QSControl.net systems. Its
compact, unobtrusive design blends well with virtually
any decor - convention facilities, retail environments,
houses of worship and a multitude of other applica­
tions. The QSControl.net NAC-100 can be quickly
and easily programmed to build an interface that
customers will understand and appreciate.
Applications
•
Convention facilities
•
Meeting rooms
•
Retail environments
•
Houses of worship
• Any permanently installed system
Features
Color graphics display
The NAC-100 wall controller offers a simple, secure,
cost-effective alternative to network PC control.
Multiple wall controllers can be deployed in any
project and used simultaneously to manage different
aspects of your system.
Power over Ethernet
Recall Global Presets
Rotary "wheel" control of an entire system
Controllers can track each other
Available color options black or white
QSControl.net System Solution
Wireless Remote
Laptop with
QSControl.net
Software
Fill 1П
QSControl.net
Software
NAC-100
Up to 8
Additional Audio
Sources
Ethernet Switch | with P.O.E.
::::::
ILA v2 Louspeakers
and Subwoofers
QSControl.net/CobraNet
RAVE 522aa
BASIS 9 2 2 U Z
AcousticDesign Loudspeakers
О
QSC Amplifiers
AcousticDesign Ceiling
Loudspeakers
QSC Amplifiers
SC28 System Controller
The SC28 is a dedicated speaker processor with
factory-optimized tunings for QSC loudspeaker
systems. User-adjustable 6 band parametric equalizer, high and low shelving filters and signal delay
optimize the system for acoustic, environmental or
aesthetic considerations.
Intrinsic Correction™
• FIR filters optimize response in both frequency and time
domains by pre-correcting for physical phenomena such
as waveguide acoustical impedance and loudspeaker
cone resonances.
QSC Loudspeaker Selection
•
Select the QSC loudspeaker and configuration (2-way,
3-way, 3-way + sub). The SC28 instantly reconfigures
itself for optimal audio reproduction.
QSC Amplifier Selection
For uncompromised audio quality, the SC28 uses
48 kHz 24-bit A/D and D/A conversion with 32-bit
floating point DSP. Advanced signal processing algorithms incorporate IIR (Infinite Impulse Response) as
well as FIR (Finite Impulse Response) filters. QSC
system engineers have employed the power of the
SC28 System Controller's FIR filters to implement
Intrinsic Correction™ of the loudspeaker. Intrinsic
Correction is designed to produce flat acoustical amplitude, frequency and phase response by compensating
for physical phenomena such as the effects of waveguide acoustical impedance and loudspeaker cone
resonance. The result is excellent power response and
extremely natural, uncolored sound across the loudspeaker's frequency band and coverage area. An array
of loudspeakers with Intrinsic Correction will be very
responsive to user-applied equalization.
•
User-Adjustable Input EQ
•
Six (6) parametric filters with adjustable frequency, gain
and bandwidth.
•
High and low shelf filters with adjustable frequency, gain
and slope.
User-Adjustable Delays
•
Sub delay adjustable from 0 to 50 ms.
•
Array delay adjustable from 0 to 20 ms.
Subwoofer Management
•
Once the processor settings have been matched to
the system, the user or installer can take advantage
of the integral equalization and delay functions.
Password protection is included to prevent
unauthorized tampering.
Selectable stereo or mono-summed subwoofer.
• Adjustable subwoofer gain.
•
The SC28 is designed for simple, straightforward
operation. Audio inputs and outputs are via balanced,
line-level, analog XLR connectors. Four outputs for
each of the two inputs are provided for use with 2 or
3-way systems plus subwoofers. Tunings are selected
by scrolling through a list of QSC loudspeakers and
selecting the model on the LCD panel. A similar
process is used to select the QSC amplifiers being
used and to configure amplifier input sensitivity for
proper dynamic protection and gain structure. Settings
for future QSC products can be loaded into the SC28
via a rear-mounted USB port.
Select the QSC amplifier being used to calibrate the
drive signal to the amplifier for proper balance and
loudspeaker protection.
System is optimized for operation with or
without subwoofer.
Loudspeaker Protection
•
Optimized thermal and excursion protection for
each transducer.
• User-bypassable for output clip-limiting only.
Channel Linking
•
Select linked or independent control of stereo
channel settings.
Features
• Two (2) XLR line-level inputs.
•
Eight (8) XLR line-level outputs.
•
Front panel meters for all inputs and outputs.
•
Universal AC power input.
•
Rear-panel USB port for quick and easy loading of
new loudspeaker tunings.
DSP-30
DSP-3 | DSP-4 | DSP-30
The DSP-3 and DSP-4 are compact, 2-channel
signal processing modules that can plug into the back
of most DataPort-equipped QSC amps to conserve
rack space and simplify interconnection. They can
also be mounted into a DPX-4 remote rack mounting
bracket for use as a standalone, rack-mounted
processing unit. The DSP-3/4 are professional audio
processors featuring 24-bit/48 kHz A/D converters,
balanced inputs, and presets that can be selected
without turn-on pops or zipper noise. Their processing
power is dynamically allocated, removing the limita­
tions imposed by fixed signal-chain designs. The
power and flexibility of the DSP-3/4 eliminates
expensive outboard DSP gear, which reduces cost
and installation time and simplifies setup.
The DSP-30 is a rack-mount device almost identical to
the DSP-3. The other main differences between these
three devices are their dynamic range specifications
and output connectors.
Our PC-based Signal Manager software uses simple
drag-and-drop tools to:
•
Configure the processing functions and signal flow.
•
•
Display a graphical representation of DSP resources.
Produce hardcopy printout of signal flow and/or
parameter settings.
•
Perform firmware upgrades via RS-232.
Each channel includes:
•
Crossover filters: Bessel, Butterworth, Linkwitz-Riley.
•
Compressors and limiters.
•
Multiple parametric EQs.
•
Precision attenuation (0.1 dB steps).
•
High- and low-shelf filters.
•
Mix post-crossover audio (2-to-l mixer).
•
Multiple delays (max. 910 ms).
•
Variable-frequency tone generator.
•
Pink and white noise generators.
•
Signal mute, splitter, and polarity reversal.
Model
Dynamic Range (unweighted)
Output Conneflors
DSP-3
>93 dB, 20 Hz to 20 kHz
3-pin Euro-style
DSP-4
>104 dB 20 Hzto20 kHz,
1.5,4,9 V sensitivities
XLR
1.5, 4, 9 V sensitivities
DSP-30
>95 dB 20 Hz to 20 kHz,
1.5, 4 and 9 V sensitivities
The DSP is configured with an easy-to-use software
interface. Signal processing icons from the toolbar are
dropped onto the workspace and the signal path is
routed with simple drawing tools.
XLR
1;Я!И
4JE55* CSM Series
Concert Stage Monitor Systems
Concert Systems
CSM10 I CSM12 | CSMI5
The CSM Series are "system packages" comprised
of stage monitor loudspeakers, proprietary digital
processing and high-power amplifiers in a tightly integrated design that offers the highest output to size
ratio of any premium brand stage monitor on the
market to date. Combining elegant industrial design
with state of the art driver and waveguide technology,
these very low-profile wedges embody all the
contemporary attributes asked for by today's most
demanding monitor engineers. Achieving all this
requires very specific power and digital processing.
The amazing performance of the CSM models is a
result of extensive and sophisticated application of
digital signal processing. The processing algorithms
can not be readily replicated on other DSP platforms.
CSM Series are designed only for use with the appropriate QSC processing using a digital controller from
the QSControl.net™ series of processors.
Selectable Coverage Pattern
CSM monitors utilize a selectable pattern control
"shutter" system that enables the user to limit the
amount of high-frequency energy spilling over into the
audience, while increasing its upstage coverage angle.
By opening the shutter, the vertical coverage is
converted to an asymmetrical pattern of +45° and
-75° off axis, while maintaining a nominal 50° pattern
?A
in the horizontal. With the shutter closed, the enclosure can be used as a wide coverage 150°H x 50°V
utility fill speaker.
Internal Angle Adjusters
In addition to the generous upstage
coverage of the CSM waveguide,
special integral hardware provides
up to an additional 15°, in 1 °
increments, of angle to the enclosure to gain more extreme
upstage coverage.
Hidden and Protected Connectors
One of the problematic conditions that have long
plagued most stage monitor designs is the location of
the input and output speaker connections. If they are
located on the sides, they can often be in the way
when placing multiple monitors side by side. If they
get mounted on the down-stage side (facing the audience), they tend to become unsightly and cluttered in
view from the audience. If they
are placed on the up-stage side
(facing the musician), they tend
to wind up under the performers
feet and often get damaged or
broken during performances.
CSM10
С5МП
CSM15
System Type
2-way wedge
2-way wedge
2-way wedge
Frequency Range (-10 dB)
70 Hz - 20 kHz
55 Hz - 20 kHz
45 Hz - 20 kHz
Frequency Response (±3 dB)
80 Hz - 20 kHz
65 Hz - 20 kHz
55 Hz - 20 kHz
Wedge
50° H x +457-75° V
50° H X +457-75° V
50° H x +45°/-75° V
Multipurpose
!50°Hx50°V
150°Hx50°V
150° H x 50° V
Passive
400W
500W
650W
Low-frequency
400 W
500W
650W
High-frequency
HOW
HOW
now
Passive
95 dB
97.5 dB
96.5 dB
Low-frequency
96 dB
98.5 dB
97 dB
High-frequency
108.5 dB
108 dB
108.5 dB
Passive
127 dB
130.5 dB
130.6 dB
lowlioqiiiiiiy
128 dB
131.5 dB
131.1 dB
High-lrequency
134.9 dB
134.9 dB
134.9 dB
Low-frequency
10"/3" voice coil woofer
12"/4" voice coil woofer
15"/4" voice coil woofer
High-frequency
3" diaphragm/1.4" exit
3" diaphragm/1.4" exit
3" diaphragm/1.4" exit
Dimensions (HWD) inches
11.87" x 14.7" x 24"
11.87" x 19.7" x 24"
12.87" x 21.7" x 26"
Dimensions (HWD) mm
301.5 mm x 373.4 mm x 310.6 mm
301.5 mm x 500 mm x 610.6 mm
326.9 mm x 551 mm x 662 mm
Net Weight (each)
60 lb/27.2 kg
77 lb/34.9 kg
B6 lb/39 kg
Nominal Coverage (-6 dB)
Power Handling (Continuous)
Sensitivity (SPL 1 W at 1 m)
Max Calculated Output (SPL at 1 m)
Driver Information
QSC CSM monitors utilize a unique recessed
connector pocket mounted on the bottom side of the
enclosure, that with the use of its four corner rubber
feet, enable the user to dress the cables in any direc­
tion needed (360°), while fully protecting the cable
end connectors from damage or sight issues.
Available CSM Accessories
•
Yoke / Pole Mount
CSM drive rack: BASIS 922az,
PL325 and PL380 amplifiers.
WideLine-10
Line Array System
Concert Systems
Instiled Sound
WL2102-W
The WideLine™ WL2102-w is a compact, high-output,
wide dispersion line array loudspeaker system renowned
for its ability to meet and exceed requirements for appli­
cations ranging from corporate meetings to large venue
reinforcement of high-level
popular music. From ballrooms
о^^?.1?™**^
to churches to concert venues,
>: .-"' „ ,T
*'•-, if
WideLine-10 provides fullrange, warm, open, natural
sound with exceptionally wide
horizontal coverage (140°).
Wide coverage provides more latitude in array place­
ment and may reduce or eliminate the need for
supplemental fill speakers.
Each WideLine-10 array element consists of two 10",
long-throw, low-frequency drivers in a ported trape­
zoidal, premium quality birch plywood enclosure.
The high-frequency component is a 3" diaphragm,
neodymium high-frequency driver mounted on QSC's
patented* multiple aperture diffraction slot waveguide.
Both LF transducers handle low frequencies, but only
one extends into the mid-frequencies thus reducing
phase and coverage anomalies in the critical crossover
region. The system may be operated in either
bi-amplified or tri-amplified mode.
A strong emphasis has been placed on reduction of
system setup time and labor costs. Two array grids are
available: The small grid supports up to 8 flown enclo­
sures or 4 stacked; the large array frame supports up to
24 flown or 12 stacked.
'Patent No. 7,177,437
Power Handling'
II/MF
600 W
80 W
HI
Available WideLine-lO Accessories
Peak Output'
LF/MF
133 dB/133 t
Driver Information
LF
2x10" transducer, 3" voice coil,
ferrite magnet
WL Small Grid: May be used to stack four (4) or fly
eight (8) WL2102-w.
AF2102-LA: May be used to stack twelve (12) or fly
3" titanium diaphragm,
neodymium magnet
II!
Controls / Seledors
Bi-amp/tri-amp selector switch, LF/MF
shading switch
twenty-four ( 2 4 ) WL2102-w.
WL-10 Eight-Pack Rack: Transport/storage unit,
accommodates eight (8) WL2102-W plus one AF2102-LA.
WL-Case: Transport/storage case, holds three (3)
Input Connedors
NL8x2
Suspension /
Attachment Point
Integral rigging system, vertical splay
adjustable in Г increments
from 2°-10°, plus 0°
Dimensions (HWD) inches
10.8" X 27.4" X 20.75"
Dimensions (HWD) mm
274 mm x 696 mm x 527 mm
Net Weight
WL2102-w:83lb/37.7kg
WL2102-W plus one Small Grid.
AF8-10: Adapter frame that allows suspension of WL3082
under WL2012-W.
/ Continuous IEC specified test signal, 2 hours bi-omp mode
unless otherwise slated.
2 Calculated at I m using power capacity and system sensitivity.
6 dB peak-to-average signal ratio assumed.
Empty WL-10
Fully loaded WL-10
Eight Pack Rack.
Eight Pack Rack.
27
WL218-sw array shown with
a combination WideLine-10
and WideLine-8 array.
WideLine-10 Subwoofers
Concert Systems
Installed Sound
using the interlocking feet and recess features. For ease
of transport, the WL218-sw includes a caster pallet with
rugged 3.5" ball bearing casters and an easy-to-use,
snap-on mechanism for attachment to the enclosure.
GP218-SW
The WL218-sw and the GP218-sw are premium, highperformance dual 18" subwoofers designed for use in
the most demanding touring or installed concert applications. They are acoustically identical subwoofers, differing
primarily in suspension hardware.
With an impressive combination of punch, lowfrequency extension and musical accuracy, these
subwoofers are ideal companions for the acclaimed
QSC WideLine™ Series as well as other professional
sound reinforcement systems. The 18" woofers incorporate a double layer spider and triple roll surround
for extended and controlled excursion at extreme
power. The 4" voice coil is wound on a fiberglass
former to prevent deformation at high operating
temperatures and is extensively vented to reduce
power compression. Both enclosures are constructed
of premium quality birch plywood with extensive
internal bracing and finished to stand up to heavy use.
WL218-SW
The WL218-sw is equally at home in the air or ground
stacked. Using the AF218-sw array frame, up to eight
WL218-sw subwoofers may be suspended with a 10:1
design factor. The subwoofers may be stacked vertically
The GP218-sw omits the WL218-sw suspension
hardware and trapezoidal shape but retains all the
acoustical performance of the WL218-sw at a lower
cost. For ground-supported applications, the
subwoofers may be stacked horizontally using their
interlocking feet and recess features machined into
the enclosure's top panel. For suspension in permanent installations each GP218-SW subwoofer includes
a total of sixteen (16) threaded M10 inserts. An
optional transport caster pallet is available.
GP218-SW
WL2I8-SW
System Гуре
2 x 1 8 " vented subwoofer
2 x 1 8 " vented subwoofer
Frequency Range
(-10 dB)
27.4 Hz - 1.2 kHz (without processing)
31 Hz - 1 kHz (without processing)
Frequency Response
(±3 dB)
31.4 Hz - 240 Hz (without processing)
37 Hz - 200 Hz (without processing)
Power handling'
1700W
1700W
Peak output ;
140.5 dB
139 dB
Driver Information
LF
Dual 18" transducers, 4" voice coil,
ceramic magnet assembly
Dual 18" transducers, 4 " voice coil,
ceramic magnet assembly
Input Connectors
2 x NL4 in parallel
2 x NL4 in parallel
Suspension / Attachment Point
16 x M l O threaded inserts
Integral rigging system, vertical splay
adjustable in Г increments from 0° -10°
Dimensions (HWD) inches
20" x 47.17" X 30"
21.3" x 45.9" X 34.75"
Dimensions (HWD) mm
508 mm x 1198 mm x 762 mm
541 mm x 1166 mm x 882 mm
191 l b / 8 6 . 6 kg-speaker only
204 lb / 92.5 kg - speaker only
244 l b / 1 1 0 kg-includes dolly
System Performance
Net Weight (each)
1 Continuous IEC specified test signal, 2 hours unless otherwise stated
2 Calculated at I m using power capacity and system sensitivity. Assumed 6 dB peak-to-average signal ratio.
Available WideLine-IO Subwoofer Accessories
AF218-sw: Array frame.
CVR218: Soft cover for WL218-sw.
CVRGP218: Soft cover for GP218-sw.
CP218-0: Caster pallet for CP218-sw.
CP218-1: Caster pallet for GP218-sw, includes
a padded soft cover.
For the WL218-sw the caster pallet
and soft cover is included.
CP218-0 caster pallet.
CP218-1 caster pallet
with soft cover.
WL3082
Flexible Arrays
Designed for the most demanding concert and installation audio professionals, the WideLine™ WideLine-8
system packs full size line array performance into an
ultra compact package measuring less than 20" (508
mm) wide and 9" (229 mm) high. WideLine-8 fits
"difficult" venues with height or sightline restrictions
that limit the placement and size of the array. It eases
An elegantly simple 4-point suspension system combined with light weight, compact size and excellent
handling ergonomics mean that one crewperson can
easily deploy an array. A single AF3082-L array
frame suspends up to twelve line array elements or
up to twelve line array elements plus four subwoofers.
iMtr.pnil icqiiiiemenls In avoid rising lnol aisls
Arrays can be assembled using only WL3082
elements for events where extreme low end below
62 Hz is not required. For additional subbass impact,
WL212-sw subwoofers can be flown at the top of the
array, or behind the fullrange array by utilizing the
EB3082 extension bar.
Each tri-amplified WideLine-8
OXSHM'ONA^
element uses a pair of highpower neodymium 8"
M O M Typical
Line Arrav Solutions
low-frequency drivers. Both
generate the low frequencies, but to maintain wide
140°
140° horizontal coverage at
crossover, only one extends
into the mid-range. High frequencies are handled by
a 3" diaphragm, neodymium compression driver on
QSC's patented* multiple aperture diffraction slot
waveguide. Enclosures are Baltic birch plywood with
an environmentally friendly, field-repairable waterborne polymer finish and lightweight, rustproof
aluminum suspension fittings.
'Patent No. 7,177,437
Arrays of up to twelve WL3082 modules, with four
WL212-sw subwoofers flown behind can be accommodated by the combination of 2 x AF3082-S small
array frames and a single EB3082 extension bar. As
many as twelve WL3082 modules can be suspended
using one AF3082-S while the AF3082-L large array
frame can be used to assemble arrays of up to twelve
WL3082 modules alone or suspended below up to
four WL212-sw subwoofers. The AF8-10 adapter
frame allows the user to add WL3082 WideLine-8
arrays beneath WL2102 WideLine-10 arrays. The
PB3082 pullback bar can be used to attain extra
downangle in flown arrays or as a suspension bar
for arrays of up to eight WL3082 modules.
WL3082
System Type
Dual 8", 3-way, tri-amp line-array
Frequency Range (-10 dB)
62 Hz - 20 kHz
Frequency Response (±3 dB)
68 H z - 1 8 kHz
Nominal Coverage
140° H
Power Handling'
LF/MF/HF
250W/250W/85W
Peak Output'
II / M l /HF
Six WL3082 shown with two WL212-sw
behind array, hung from two AF3082-S
and one EB3082.
.
Driver Information
LI
Dual, 8" woofer, 2.5" voice coil
1.4" exit, 3" diaphragm, neodymium
magnet compression
Ml
li| il '
128 dB/ 128 dB/ 133 dB
'Mill
NL8x2
Suspension /
Attachment Point
Integral rigging system, vertical splay
adjustable in 1° increments
fromO"-10°
Dimensions (HWD) inches
9" x20" x 16"
Dimensions (HWD) mm
229 mm x 508 mm x 406 mm
Net Weight (each)
38 l b / 1 7 kg
/ Continuous ICC specified test signal, 2 hours unless otherwise stated.
2 Calculated at I m using power capacity and system sensitivity
6 dB peak-to-average signal ratio assumed.
r^mwrm
|£Q£jjj
Optimized Groundstacking
The WideLine-8 system is equally at home in the air
or ground stacked. WideLine-8 rigging doubles as an
optimized groundstacking system. The WideLine-8 sub
suspension system includes a unique provision that
allows the lowest line array element stacked over a
sub to be tilted up or down by as much as 10°,
offering better coverage of listeners near the stage.
WideLine-8 subs can be used as a base for stacking
up to six WideLine-8 elements.
Four WL3082 on top of two WL212-sw.
WL212-sw
GP212-sw
WideLine-8 Subwoofers
GP212-SW
Concert Systems
Installed Sound
The GP212-sw omits the WideLine-8 compatible
suspension hardware but retains all the acoustical
performance of the WL212-sw at a lower cost. For
suspension in permanent installations each GP212-sw
subwoofer includes a total of six (6) threaded Ml 0
inserts. For ground-supported applications, the
subwoofers may be stacked horizontally using their
interlocking feet and recess features machined into
the enclosure's top panel. A screw-in (M20) pole
mount has been added to provide flexibility in use
with small 2-way pole mount full-range speakers.
The WL212-sw, WideLine-8 Subwoofer, and the
GP212-sw are acoustically identical subwoofers,
differing primarily in suspension hardware. Both
subwoofers set a new benchmark for extraordinary
acoustic output from a miniscule enclosure. At first
glance, the enclosure seems too small for a pair of 4"
voice coil, long excursion 12" woofers. The extremely
low profile (under 15" / 38 mm) also makes the
WL212-sw sub a great choice for installed and
portable use under a stage or in other tight quarters.
The 4th order bandpass design produces 135 dB
peak SPL and has I_F extension to 32 Hz - all the
power and punch needed for popular music.
Both Models
•
135 dB SPL peak output capability.
•
32 Hz - 107 Hz frequency range.
•
Premium birch plywood with extensive
internal bracing.
WL212-SW
Enclosure width matches the WL3082 (WideLine-8)
allowing it to be flown above or behind a WideLine-8
array. Adding WL212-sw subwoofers to tri-amplified
WL3082 arrays creates a 4-way active system. A
WideLine-8 system is equally at home in the air or
ground stacked. WideLine-8 rigging doubles as an
optimized ground-stacking system. The WL212-SW
suspension system includes a unique provision that
allows the lowest line array element stacked over a
sub to be tilted up or down by as much as 10°,
offering better coverage of listeners near the stage.
WideLine-8 subs can be used as a base for stacking
up to six WideLine-8 elements.
32
Dual 12" woofers in a 4th order band-pass enclosure.
•
WL212-sw
•
May be flown at the top of a WL3082 array
or behind the array.
•
Integral suspension hardware also supports
WL3082 in ground stack applications.
GP212-SW
•
Six (6) threaded M10 flypoints
for suspended applications.
•
M20 threaded pole-socket
for sub/sat use.
Two WL212-sw shown hung
from AF3082-L with six WL3082
hung beneath.
CP212-SW
WL212-SW
System Type
Dual 12", 4th order bandpass
subwoofer
Dual 12", 4th order bandpass
subwoofer
Frequency Range
(-10 dB)
32 Hz-107 Hz
32 Hz-107 Hz
Frequency Response
(± 3 dB)
40 Hz-100 Hz
40 Hz-100 Hz
Power handling'
1100 W
1100W
Peak output <
135 dB
135 dB
Driver Information
LF
Dual 12" transducers, 4" voice coil,
ceramic magnet
Dual 12" transducers, 4" voice coil,
ceramic magnet
Input Connectors
2 x NL8 in parallel
2 x NL8 in parallel
Suspension / Attachment Point
6 xMIO threaded inserts
Integral, non-adjustable
Dimensions (HWD) inches
15" x 20" x 29"
15"x20"x29"
Dimensions (HWD) mm
381 mm x 508 mm x 737 mm
381 mm x 508 mm x 737 mm
Net Weight (each)
99.5 l b / 45.1 kg
109 lb/49.4 kg
/ Continuous IEC specified test signal, 2 hours unless otherwise stated
2 Calculated at I m using power capacity and system sensitivity. Assumed 6 dB peak-to-average signal ratio.
|JQj
Available WideLine-8 Accessories
•
AF3082-L: Large array frame, supports up to twelve (12)
WideLine-8 elements and four (4) WideLine-8 subs with
10:1 design factor.
•
AF3082-S: Small array frame, supports up to twelve (12)
WideLine-8 elements with 10:1 design factor.
•
AF8-10: Adapter frame that allows suspension of WL3082
under WL2012.
•
EB3082: Extension bar, required for system with the
subwoofers flown behind the main array.
•
PB3082: Allows extra down-angle in flown arrays and
functions as a suspension bar for small WL3082 arrays.
•
CP3082: Caster pallet for four (4) WL3082 line array
elements, includes a padded soft cover.
•
CP212-1: Caster pallet for one (1) WL212-sw or one (1)
GP212-sw, includes a padded soft cover.
•
CP212-2: Caster pallet for two (2) WL212-sw or two (2)
CP212-SW, includes a padded soft cover.
GP212-sw shown with HPR.
CP212-2
CP3082
53
Combination
WL-10 and WL-8 Array
with WL218 Subwoofers
Combination
WL-10 and WL-8 Array
with WL218 Subwoofers
Wireless Laptop
System Control
CP218 Subwoofers Ground-stacked
Ethernet Switch
GP218 Subwoofers Ground-stacked
BASIS
Digital Console
with CobraNet1"
Outputs
PowerLight 3
Amplifiers
PowerLight 3
Amplifiers
CSM Series Stage Monitors
Fully Networked
Concert System Solutions
QSC Concert Systems offer the highest degree of flexibility while providing maximum use and scalability in
inventory management. Using QSControl.net digital
processors throughout the system allows the user
to easily reconfigure and combine multiple speaker
systems at a "click of the mouse", while maintaining
full system remote control and monitoring of the
entire "front to back" audio chain via wired and/or
wireless PC control.
34
BASIS 922az, PL325 and
PL380 amplifiers.
The AF3082-wx is a compatible, aluminum array
frame for use when suspending the WL3082-wx. Array
frames for the standard WL3802 are not compatible
with the WL3082-wx.
WLWX Weatherized WideLine
Installed Sound
GP218-WX
WL2102-WX
The GP218-wx is a weather resistant, installation
version of the WideLine-10 GP218 subwoofer. The
standard version includes no suspension provisions
but M l 0 suspension points may be added on request.
The WL2102-WX is a weather resistant, installation
version of the WideLine-10 WL2102-W line array. All
rigging hardware is removed and replaced with four
female M10 fittings (eight total) mounted to either
end of the enclosure. The loudspeaker is designed
for 3-way operation only and no handles are
provided. An adjustable, external, bolt-on rigging
system for box-to-box connection and adjustment
of splay angles is included.
Enclosure Construction
WideLine-wx models are constructed using premium
birch plywood which is full encapsulated in fiberglass.
The input connector plate is replaced by a hardwired,
captive, UV resistant, outdoor-rated (direct burial)
cable with a gland-nut through the cabinet for water­
proofing. The cable will be 3 meters in length unless
otherwise specified at the time the order is placed.
Grilles are stainless steel covered in outdoor rated,
vinyl coating and lined with acoustic foam and a fine
woven stainless steel mesh.
The AF2102-wx is a compatible, aluminum array
frame for use when suspending the WL2102-wx. Array
frames for the standard WL2102-W are not compatible
with the WL2102-wx.
WL3082-WX
The WL3082-wx is a weather resistant, installation
version of the WideLine-8 WL3082 line array. All
rigging hardware is removed and replaced with four
female M10 fittings (eight total) mounted to either
end of the enclosure. The loudspeaker is designed for
3-way operation only. An adjustable, external, bolt-on
rigging system for box-to-box connection and
adjustment of splay angles is included.
Delivery
WideLine WX models are strictly built to order. Please
allow 90 days plus shipping time from the time the
P.O. is delivered to QSC for delivery.
WUlOZ-wx
WLI082-WX
CP218-WX
System Type
Tri-amp line array element
Tri-amp line array element
2xl8"ventedsubwoofer
Frequency Range (-10 dB)
48 Hz - 20 kHz
62 Hz - 20 kHz
27.4 Hz -1.2 kHz (without processing)
Frequency Response (±3 dB)
55 H i - 1 8 kHz
68 Hz-18 kHz
31.4 Hz - 240 kHz (without processing)
Nominal Coverage
140° H
140° H
М/Л
Power Handling'
1F / Ml
600 W
250 W
1700W
80 W
85 W
МУА
Peak Output •'
LF/MF
127 dB/ 133 dB
122 dB/128 dB
140.5 dB
Driver Information
LF
2x10" transducer, 3" voice coil, ferrite magnet
2x10" transducer, 3" voice coil, ferrite magnet
2x18" transducers, 4" voice coil, ceramic magnet
3" titanium diaphragm, neodymium magnet
3" titanium diaphragm, neodymium magnet
1М/Л
Input Connectors
Tinned, bare wire
Tinned, bare wire
Tinned, bare wire
Suspension / Attachment Point
Integral rigging system, vertical splay adjustable
in Г increments from 0°-10°
Integral rigging system, vertical splay adjustable
in 1° increments from 0°-10°
None ( M I 0 points available by request)
Dimensions (HWD) inches
11.75" X 27.25" X 18.5"
9.5" x 20" x 15.5"
21.13" X 30.13" X 47.32"
Dimensions (HWD) mm
298 mm x 692 mm x 470 mm
241 mm x 508 mm x 394 mm
537 m m x 765 m m x 1202 m m
Net Weight
92.5 lb/42 kg
61 lb/27.7 kg
215 l b / 9 7 . 5 kg
HI
HI
/ Continuous IIC specified test signal, 2 hours bi-amp mode unless otherwise stated.
2 Calculated at I m using power capacity and system sensitivity. 6 dB peak-to-average signal ratio assumed.
В
I LA Series v2
Installation Line Array
Installed Sound
Most line array systems are designed for touring
applications which require extreme ruggedization
and expensive suspension hardware. By focusing on
installation applications QSC drove cost out of the
I LA System while retaining the performance of
high-end touring line array systems. ILA System v2
takes this concept and builds on it by offering a
complete and accessible solution consisting of
processing, amplification, line array, subwoofer
and suspension accessories.
WL2802-i with WL118-sw
using EB2082-i extension
bar and FB2082-i fly-bar.
WL2082-I
Each Installation Line Array element uses a pair
of high-power, neodymium magnet, 8" diameter
low-frequency drivers. For high frequencies, a pair of
1.75" (voice coil diameter) neodymium compression
drivers with titanium domes are mounted on a
patented* multiple aperture diffraction waveguide that
provides extremely wide coverage (140°). As a result,
a WL2082-i system will rarely require additional side
or center fill speakers and solid stereo imaging is
preserved across the entire listening area.
Available in black or white, the WL2082-i enclosure is
made of high impact polystyrene with extensive internal
ribs to eliminate acoustic losses due to sidewall flex.
The Installation Line Array may be used in outdoor
applications where the system is not directly exposed
to the elements.
4КЩЪ
GPT18-sw Subwoofer
The GP118-sw omits the ILA compatible suspension
hardware but retains the identical acoustical perfor­
mance of the WL118-sw at a lower cost. Each
GP1 18-sw includes a total of eight (8) threaded
M10 inserts for single box suspension in permanent
installations. In ground-supported applications,
multiple units can be stacked horizontally utilizing the
interlocking feet and recess features machined into
the enclosures top panel. Also included on the GP
version is a screw-in (M20) pole mount to provide
flexibility as a "Sub-Sat" system when used with
full-range pole mount speakers.
WL118-sw Subwoofer
The WL118-sw is a single 18" version of the popular
WideLine-10 touring, dual 18" subwoofer. ILA subs
may be suspended at the top of an ILA array using the
standard FB2082-i array frame. When trim height is
limited, the ILA sub may be suspended behind the
array using the available EB2082-i extension bar.
( , N If, <;w
*Potent No. 7,177,437
',(,
WL2802-I
CP118-SW
WL118-SW
System Type
3-way line array element,
Bi-amp or Tri-amp
Vented box,
direct radiating
Vented box,
direct radiating
Frequency Range (-10 dB)
68 Hz - 22 kHz
29 Hz - 800 Hz
29 Hz - 800 Hz
Frequency Response (±3 dB)
80 Hz - 20 kHz
32 Hz - 200 Hz
32 Hz - 200 Hz
Nominal Coverage
140° H
N/A
N/A
Power Handling ;
LF/MF/SF
400 W
10O0W
1000 W
I00W
N/A
N/A
Peak Output'
133 dB
124 dB
124 dB
Driver Information
2 x 8 " transducers; 2" voice coil;
neodymium magnet
18" transducer, 4 " voice coil,
ferrite magnet
18" transducer, 4" voice coil,
ferrite magnet
2 x 1.75" titanium diaphragm,
neodymium magnet
N/A
N/A
Controls / Selectors
Bi-amp/tri-amp selector switch,
N/A
LF/MF shading switch
N/A
Input Connectors
2 x NL8 in parallel
2 x NL8 in parallel and
2 x NL4 in parallel
2 x NL8 in parallel and
1
xNI-l in parallel
Suspension /
Attachment Point
Integral rigging system,
vertical splay adjustable in
1 degree increments from
0-10 degrees
8 x MIO threaded inserts
Integral, non-adjustable
(straight array only)
Dimensions (HWD) inches
11.8" x 27" x 13.4"
22.1" x 27.6" x 30.3"
22.1" X 27.6" x 30.3"
Dimensions (HWD) mm
300 mm x 686 mm x 340 mm
562 mm x 702 mm x 771 mm
562 mm x 702 mm x 771 mm
Net Weight (each)
37 lb/16.8 kg
107 lb/48.5 kg
111 lb/50.4 kg
Hl-
EASE Focus
LF
HF
Software
This free software may be downloaded
from the support section of the QSC
website and is available for ILA,
WideLine-IO and WideLine-8.
EASE Focus is a software tool that aids
in system planning and deployment.
Functions performed include:
/ Continuous ICC specified test signol, 2 hours.
2 Calculated at I m using power capacity and system sensitivity.
6 dB peak-to-average signal ratio assumed.
•
Calculating the number of enclosures
required for a given space.
•
Determining optimum splay angles between
enclosures.
•
Calculating the angle to set the array grid
in a single (variable) pick-point or fixed
suspension point application.
•
Predicting the acoustical response and SPL
throughout the venue.
Processing
The SC28 is a 2 input, 8 output digital system
controller containing pre-programmed tunings for the
ILA and other QSC loudspeaker systems. In addition
to the preset tunings, the SC28 offers user-adjustable
equalization and delay. Simple to operate yet
uncompromised in audio quality, the SC28 uses
48 kHz, 24-bit A / D and D/A conversion with 32-bit,
floating point DSP for wide dynamic range and low
distortion. See page 21 for SC28 product Using.
The ILA v2 System
From Console
ILA with WL118-SW
Subwoofer
Available ILA Accessories
FB2082-i: Fly-bar, may be used with either
W L 2 0 8 2 - i o r W L l 15-sw.
EB2082-i: Extension bar allows suspending
WL115-sw behind WL2082-L
PB2082-i: Pullback bar for WL2082-i.
QRP-KIT-1: Four quick release pins, for use
in place of included bolts.
GS115-sw: Ground stack kit for WL115-sw.
AB2082-i: Allow increased splay
between enclosures.
RMX Series Amplifiers
RMX2450 - HF
RMX5050 - MR LF, SF
57
AcousticDesign™ Series
Ceiling Loudspeakers
Installed Sound
AcousticDesign in-ceiling speakers are ideal for
commercial applications including hotels, restau­
rants, pubs, offices, retail spaces, convention centers,
recreation facilities, houses of worship, and airports.
Delivering higher SPL over an unusually wide
frequency range, AcousticDesign loudspeakers provide
natural, musical, sound with very low distortion. AD-C
ceiling speakers and AD-S surface mount speakers
are designed for seamless sonic integration using
common driver technologies.
«2П13»
AcousticDesign loudspeakers are supported in EASE
Address software, a design tool for modeling distrib­
uted loudspeaker systems in two dimensions. Using
Address, a system designer can quickly develop a
simple design for a ceiling loudspeaker layout and
predict system performance. EASE Address is available
from the QSC web site at no charge.
AD-C42T
The AD-C42T ceiling mount loudspeaker is designed
for background music and general purpose playback,
and is acoustically matched with other AcousticDesign
Series products. Rated for 40 watts continuous and
160 watts peak power handling, with 88 dB SPL
sensitivity, the compact AD-C42T is suitable for any
ceiling installation where a small, minimally intrusive
footprint is desired.
The 4" woofer has a polypropylene cone and
synthetic rubber surround for reliable operation in
humid environments. In its sealed enclosure it is
optimized to deliver usable output below 70 Hz. The
0.75" dome tweeter has a titanium diaphragm and
a cloth surround. Its coaxial post is mounted slightly
off center in the low frequency driver to minimize
destructive interference and maintain smooth 100°
conical dispersion.
The baffle and mounting tabs are molded highimpact polystyrene. The rear enclosure is heavy gauge
powder coated steel. An attractive aluminum grille
is backed with acoustically transparent white cloth.
58
%j сол о
The input cup on the rear of the enclosure features a
conduit attachment point, plus an additional knockout
for daisy-chain wiring. The high-temperature-resistant
ceramic input screw terminal complies with European
safety standards.
The AD-C42T ships with C-rings and tile rails.
New construction rings (ADC-NC4) and mud rings
(ADC-MR4) are available separately. A 70/100 volt
transformer with multiple taps and an 8П bypass is
built-in.
AD-C81TW
The AD-C81Tw ceiling mount subwoofer is designed
to supplement AcousticDesign systems with lowfrequency extension that is acoustically matched
with both ceiling-mount and surface mount
AcousticDesign Series products. Rated for 100 watts
continuous and 400 watts peak power handling, the
AD-C81Tw extends low-frequency output below 40
Hz. Its built-in 120 Hz low-pass filter is switchable
from the front panel.
For reliable operation, even in high humidity, the 8"
woofer has a polypropylene cone and synthetic rubber
surround. The driver works optimally with the large
port to provide solid low-frequency extension without
undesirable port turbulence. This highly efficient
design produces 92 dB SPL sensitivity.
The baffle and mounting tabs are molded high-impact
polystyrene. The rear enclosure is heavy-gauge powdercoated steel. An attractive aluminum grille is backed
with acoustically transparent white cloth. For minimum
vertical clearance, the input cup is on the side of the
enclosure: it features a conduit attachment point, plus
an additional knockout for daisy-chain wiring. The hightemperature-resistant ceramic input screw terminal
complies with European safety standards.
AD-C42T
AD-CIHT
AD-CI52ST
AD-C81Tw
System Type
2-way, ceiling / (lush mounted,
sealed system
2-way, ceiling / (lush mounted,
ported system
Shallow can, 2-way,
ceiling / flush mounted,
ported system
Subwoofer,
celling / flush mounted,
ported system
Frequency Range
(-10 dB)
60 Hz - 20 kHz
65 Hz - 20 kHz
53 Hz - 20 kHz
28 Hz - 208 Hz
Frequency Response
(±3 dB)
72 Hz - 20 kHz
85 Hz - 20 kHz
63 Hz - 20 kHz
39 Hz - 184 Hz
Nominal Coverage
100° conical
90° conical
ll>U"u
N/A
Full Range
Power Capacity'
Sensitivity'
Peak SPL'
40W(100hrs)
88 dB
110 dB
40W(100hrs)
86 dB
108 dB
40W(100hrs)
87.5 dB
I09d8
lOOW(lOOhrs)
92 dB
118 dB
Driver Information
LF
4" weather resistant,
polypropelene cone woofer
5.25" weather resistant,
low distortion fiberglass cone woofer,
25 mm voice coil, neodymium magnet
5.25" weather resistant,
low distortion fiberglass cone woofer,
25 mm voice coil, neodymium magnet
8" weather resistant,
polypropelene cone woofer,
rubber surround
0.75" titanium dome tweeter,
rubber surround
1" titanium dome tweeter,
rubber surround
I" titanium dome tweeter,
rubber surround
N/A
Controls / Selectors
70 V: 30, 15,7.5, 3.8 W
100 V: 30,15,7.5 W
8П Externally
Selectable
70 V: 30, 15,7.5, 3.8 W
100 V: 30, 15, 7.5, 3.8 W
80 Externally
Selectable
70 V: 30, 15, 7.5, 3.8 W
100 V: 30, 15, 7.5,3.8 W
8 0 Externally
Selectable
70 V: 60, 30,15, 7.5 W
100 V: 60, 30,15 W
80 Externally
Selectable
Input Connectors
Ceramic block or 4-pin Euro terminals,
fire protective sub-chamber
4-pin Euro terminals,
fire protective sub-chamber
4-pin Euro terminals,
fire protective sub-chamber
Ceramic block or 4-pin Euro terminals,
fire protective sub-chamber
Suspension /
Attachment Point
N/A
N/A
N/A
N/A
Dimensions (HWD)
inches
7.5" x 7.5" x 9.3"
8.5" x 8.5" x 9.3"
12.6" x 12.6" x 3.75"
12.6" x 12.6" X 14.8"
Dimensions (HWD)
mm
191 mmx 191 mm x 236 mm
216mmx 216mmx236mm
321 mmx 321 mmx 95 mm
320 mm x 320 mm x 376 mm
Net Weight (each)
6.1 lb/2.7 kg
7.5 lb/3.4 kg
В lb/3.7 kg
20 lb/9.1 kg
III
,ll
7 Continuous IEC specified test signal, 2 hours unless otherwise stated. 2 Based on nominal impedance, measured in full space I W (
3 Calculated using specified power capacity and system sensitivity. 6 dB peak-to-average signal ratio assumed.
The AD-C81Tw ships with C-rings and tile rails.
New construction rings (ADC-NCS) and mud rings
(ADC-MRS) are available separately. A 70/100 volt
transformer with multiple taps and an 8fi bypass
is built-in.
AD-CI52T | AD-CI52ST
Both of these high performance ceiling speakers
deliver accurate, high-fidelity sound in foreground /
background music and paging systems. A weatherresistant 5.25" transducer with a fiberglass cone,
25 mm voice coil and rubber surround delivers the
low frequencies in both the AD-CI52T and AD-CI52ST.
The high-frequency driver is a pure titanium 1" dome
tweeter with a neodymium magnet.
A custom low distortion, wide bandwidth transformer
with a laminated core is included with both models.
Multiple power taps are available on either 70 volt or
1OO volt lines. A bypass switch enables 8П operation.
The AD-CI52ST large-ported enclosure extends its lowfrequency response, while the shallow depth is ideal
for installations with limited mounting space, such
as cruise ships or in-wall placement. The AD-CI52T
is smaller and even less visually intrusive. As a fully
sealed system, the AD-CI52T is even more weatherresistant than the ported AD-CI52ST.
Available AD-C Accessories
•
ADC-MR: Mud Ring Bracket for AD-CI52T.
•
ADC-NC: New Construction Bracket for AD-CI52T.
•
ADC-MRS: Mud Ring Bracket for shallow can
model AD-CI52ST.
•
ADC-NCS: New Construction Bracket for shallow can
model AD-CI52ST.
AcousticDesign™ Series
Loudspeakers
Installed Sound
нШЩ
AD-S32T
Designed for background and general purpose audio
playback, the AD-S32T surface mount loudspeaker is
acoustically matched with both ceiling and surface
mount speakers in the AcousticDesign Series. Full
sounding and fully featured in a surprisingly small
package, the AD-S32T has 85 dB sensitivity, 30
watts continuous power handling and can handle
120 watt peaks.
The 3" woofer has a polypropylene cone and
synthetic rubber surround for reliable operation in
high humidity. It is optimized to deliver useable
output below 70 Hz. The humbucking magnet
structure can be used next to CRT monitors without
interference. The 0.75" dome tweeter has a titanium
diaphragm and a cloth surround. The waveguide
provides 100° by 100° dispersion.
The attractive, compact enclosure is molded from highimpact polystyrene, and like all the AcousticDesign
Series loudspeakers, is available in black or white
and can be painted to match any specific decor. An
aluminum grille backed with acoustically transparent
foam protects the components from the elements.
For outdoor applications, the plated screw input signal
terminals can be sealed with the included weather
cover. A wide bandwidth transformer with multiple
power taps for either 70 volt or 100 volt lines and a
bypass switch for 8 ohm operation is part of the
AD-S32T system. A versatile ball mount assembly
and yoke mount, both included, simplify installation.
AD-S52 | S52T
The AD-S52 is designed for flat, full-range output:
ideal for background / foreground music, paging,
secondary coverage in live performance venues,
or anywhere accurate reproduction and audio quality
are key requirements. Sleek, contemporary styling
blends easily into hotels, restaurants, sports bars,
convention facilities, and multimedia environments.
The AD-S52 high-output, 2-way design includes a
5.25" weatherproof, low-frequency transducer with
magnetic shielding for use next to CRT monitors, along
with a 1" neodymium tweeter. Dynamic power
protection incorporated into the crossover network
protects the system against accidental overloads. The
AD-S52T includes a 70/100 volt matching transformer
for distributed systems. A rear panel switch selects the
power level: it can also bypass the transformer
completely for 80 operation, providing greater
flexibility than many competing products.
The AD-S52 system includes a ball-mount assembly
for convenient installation in a wide variety of
orientations. The ball mount adapter's back plate
can be removed to reduce the overall depth of the
assembly and the footprint of the wall mount. A
weather-resistant, input connection cover protects
the input terminals.
Available AD-S52 | S52T Accessories
•
YM-5 Yoke Mount
AD-S82 | S82H
When higher acoustic output is called for, the
full-range AD-S82 and AD-S82H surface mount loud­
speakers are the choice for background / foreground
music and paging applications that require accurate
reproduction and audio quality. Their flat response
also makes them ideal for secondary coverage in live
performance facilities. Sleek, contemporary, yet unob­
trusive styling meets the needs of multiple venues
including hotels, restaurants, sports bars, convention
f
AD-S32T
AD-S52
ADS52T
AD-S82
(standard output)
AD-S82H
(high output)
AD-S282H
AD-S282HT
stem Type
Compact 2-way,
surface mount, ported
loudspeaker system
Compact 2-way,
surface mount, ported
loudspeaker system
Compact 2-way,
surface mount, ported
loudspeaker system
Compact 2-way,
surface mount, ported
loudspeaker system
Compact 2-way,
surface mount, ported
loudspeaker system
Compact 2-way,
surface mount, ported
loudspeaker system
Compact 2-way,
surface mount, ported
loudspeaker system
equency Range
10 dB)
65 Hz - 20 Hz
60 Hz - 20 kHz
60 Hz - 20 kHz
65 Hz-19 kHz
60 Hz - 22 kHz
60 Hz - 29,5 kHz
60 Hz - 29.5 kHz
75 Hz - 19 kHz
75 Hz-19 kHz
85 H z - 1 8 kHz
80 Hz-21 kHz
I Hz-27.7 kHz
80 Hz - 27.7 kHz
90°H x 60°V
(rotatable)
90°H x 60°V
(NiUl.lUr)
90°H x 60°V
90°H x 60°V
450 W (8 hrs)
93 dB
1 !! dB
;quency
Response
73H2
.20kH2
jminal Coverage
lOO'Hx i'»"v
90°H x 90°V
urn (90"V
ill Range
Power Capacity'
Sensitivity •
Peak SPL '
30W(100hrs)
85 dB
105 dB
60W(100hrs)
86.5 dB
110 dB
60W(IOOhrs)
86 dB
107 dB
110 W(8 hrs)
90.5 dB
117 dB
240 W (8 hrs)
90.5 dB
120 dB
450 W (8 hrs)
93 dB
125 dB
iver Information
LF
3" weather resistant,
polypropylene cone
woofer
5.25" shielded,
weather-resistant
5.25" shielded,
weather-resistant
8" fiberglass cone,
I 1/4" voice coil
8" high-power treated
paper cone,
2" voice coil,
neodymium magnet
8" high-power treated
paper cone x 2,
2" voice coil,
neodymium magnet
paper cone x 2,
2" voice coil,
neodymium magnet
HI
0.75" neodymium tweeter
1" neodymium tweeter
1" neodymium tweeter
I" titanium dome tweeter, 1" high output
neodymium magnet
I)III|II"J
diivei
1" high output
compression driver
1" high output
compression driver
jntrols / Selectors
70 V: 30,15, 7.5,3.8 W
100 V: 30, 15, 7.5 W
8П Selectable
Rotary Knol
N/A
70 V: 30,15, 7.5 3.75 W
1 (10 V: 30, 15, 7.5 W
80 Selectable
Rotary Knob
М/Л
Щ
N/A
70 V: 200,100,20,25 W
100 V: 200, 100, 50 W
8П Externally
Selectable
put Connectors
Screw terminals
5-way binding
posts x 2
5-way binding
posts x 2
Concealed 5-way
binding posts x 2,
IntelliDock mounting/
connection system
Concealed 5-way
binding posts x 2,
IntelliDock mounting
connection system
Banier Strip
Barrier Strip
(switchable: passive/active)
ispension /
tachment Point
N/A
N/A
N/Л
N/A
N/A
OmniMount РгобО.О
AIM, INIKIII
OmniMount РгобО.О
Attachment
imensions (HWD)
dies
7.9" X 4.8" x 5.5"
11.3" x 7.0" x 8.3"
11.3" x 7.0" x 8.3"
17.4" x 10.0" x l 1.2"
17.4" x 10.0" x 11.2"
26.2" x 10.2" x 11.4"
26.2" x 10.2" x l l . 4 "
imensions (HWD)
m
201 mm x 122 mm
x 140 mm
287 mm x 178 mm
x212mm
287 mm x 178 mm
x212mm
445 mm x 255 mm
x 285 mm
445 mm x 255 mm
x 285 mm
445 mm x 255 mm
x 285 mm
445 mm x 255 mm
x 285 mm
eighf (each)
4 l b / 1.8 kg
15 lb/6.8 kg
18 lb/8.2 kg
16.9 lb/7.4 kg
16.2 lb/7.7 kg
27.7 1b/12.6 kg
27.7 lb/12.6 kg
"•"
i
'
i
"
i
"
•
Continous IK specified test signal. 2 hours unless otherwise stated. 2 Based on nominal impedance, measured in full space. I [email protected] I m.
Calculated using specified power capacity and system sensitivity. 6 dB peak-to-average signal ratio assumed.
facilities, and multimedia environments. Its magneti­
cally shielded low-frequency driver is suitable for use
near CRT monitors.
The AD-S82 is a 2-way system housed in a weather
resistant, ported enclosure made from injectionmolded, high-impact polystyrene. The low-frequency
transducer is an 8" weatherproof driver with a heavyduty double-roll cloth surround. For applications
requiring higher power handling and acoustic output,
the AD582H (High Output) replaces the 1" titanium
dome tweeter used in the AD-S82 with a 1" exit
compression driver. Both models use a 90° x 60°
version of QSC's patented, rotatable Advanced
Directivity™ waveguide. Both are available with or
without a 70/100 volt transformer.
QSC's IntelliDock™ intelligent mounting system sets a
new standard for ease of installation and security. The
IntelliDock system includes everything necessary to
mount, wire, and position the speaker. A single step
locks the speaker securely onto the docking station
while simultaneously making electrical connections.
This unique and innovative design reduces installation
time and wiring, while decreasing the risk of theft.
Four mounting configurations are available, including
a standard yoke mount.
Available AD-S82 Mounting Accessories
•
ID-8 | ID-8T IntelliDock
•
YM-8 | YM-8T Yoke Mount
AD-S282H | S282HT
When additional low-frequency performance and
higher acoustical output are required, choose the
dual-8" AD-S282H with 1" exit compression driver.
For mounting flexibility, a yoke bracket is included.
The AD-S282HT includes a 70/100 volt transformer
for distributed systems. A rear panel switch selects the
power level or bypasses the transformer for 80 oper­
ation, providing greater flexibility than many
competing products.
-n
<?[=jVi> AcousticDesignIM Subwoofer
Installed Sound
AD-S28TW
The AcousticDesign Series of installation loudspeaker
products from QSC expands with the new AD-S28Tw
surface mount subwoofer system. Designed to supple­
ment audio systems by adding low-frequency extension,
the new AD-S28Tw is acoustically matched to the entire
AD Series. Rated for 250 watts continuous power
handling and able to take up to 700 watt peaks, the
AD-S28Tw is a great complement to any of the ceilingmount or surface-mount AD Series models.
The dual 8" woofers are equipped with polypropylene
cones for protection in humid environments. The
bandpass enclosure features two chambers. One
chamber is completely sealed, while the other
chamber features a large port. The bandpass design
allows for tight precise bass with extension down to
36 Hz. This highly efficient design produces a 1W at
1 m sensitivity of 94 dB SPL. The AD-S28Tw has a
built-in passive low-pass filter set at 120 Hz.
The marine grade plywood enclosure is built to the
highest standard to provide exceptional resistance to
high humidity. The zinc-plated steel grille has a black
foam backing, molded ABS endcaps and a rotatable
logo. On the rear of the enclosure is the input cup with
a hinged door to conceal the controls and input
connections. Input and output nickel plated screw
terminals accept wiring from 18 AWG (1.02 mm) to 12
AWC (2.053 mm). Two rotary switches can be found
in the input cup. One switch selects between the
70/100 volt transformer taps, while the other switch
enables or disables the internal passive low-pass filter.
The AD-S28Tw can be deployed in a number of ways.
With the included rubber feet attached, the subwoofer
can be floor or shelf-standing. Suspended installation
is available with either the included forged-shoulder
eyebolts and accessories or the included steel yoke.
AD-S28TW
System Type
Surface mount bandpass subwoofer, ported
Low-frequency Transducer
Dual 8" (200 mm) weather resistant, polypropylene
cone woofers, rubber surround
Frequency Range'
llUjUHIiy RcpiUlM' 1 1- ill.)
II i . , i l i l i . | i n | i i i i n y I'."';;' i HiilHi
Filter
w\\/
ii,Mi/
36 Hz - 205 Hz
120 Hz low-pass, passive, bypassable
Maximum Output'
Calculated Peak/Continuous Output
'II ( l u l l \|),ll(.|
4n (full space)
Nominal Impedance
124dBSPL/H8dBSPL
118dB SPL/112 dB SPL
80
Power Rating
RMS Power Handling'
250W(2hourslEC)
Recommended Max Amp Power
500 W RMS
Sensitivity
94 dB, 2.83 V, 1 m, half space (2n)
Transformers
Type
Custom low distortion laminated core,
wide bandwidth design
l,l|v.
70 V: 200,100,50,25 W / 100 V: 200, 100,50 W /
8 0 selected by switch
111/111)
111. ll
Exceeds Mil Spec 810 for humidity, salt spray and
dust; 1ЕС 60529 IP-X4 splash rating
Connectors
4 position barrier strip; 2 i n / 2 out
Dimensions (HWD) inches
15.9" X 9.9" X 22.75"
Dimensions (HWD) mm
404 mm x 251 mm x 603 mm
Weight
43 lb/19.5 kg
1 All frequency ranges specified refer to measured free field response.
2 Calculated SPL at 1m, speaker operating at rated RMS power with pink noise within
specified frequency range.
3 Maximum input power tested in accordance with ICC 268-5 recommendations,
SO Hz - 20 kHz band limiting, 6 dB signal crest factor.
42
Distributed System
Wireless Remote
Laptop with
QSControl.net
Software
QSControl.net
Software
NAC-100
Up to 8
Additional Audio
Sources
QSControl.net/CobraNet
RAVE 522aa
BASIS 922uz
I
AcousticDesign Ceiling
Loudspeakers
AcousticDesign
Loudspeakers
.
«
•
•
О " О ~ О " О
Up to 16
Additional Audio
Sources
о-о-о-о
CX Amplifiers
CX Amplifiers
AcousticDesign
Subwoofers
Distributed System Solutions
In facilities ranging from hospitality to houses of
worship to themed attractions, QSControl.net™
version 3 is capable of managing an entire venue's
digital audio routing and processing requirements. The
new NAC-100 wall controller may be programmed to
perform a broad range of simple or complex system
control tasks.
A growing selection of AcousticDesign™ ceiling
and surface mount loudspeakers powered by the
respected CX Series amplifiers give system designers
AcousticDesign Ceiling
Subwoofers
and installers the reliability and accurate reproduction
they're looking for.
Facility owners and system designers are increasingly
recognizing the need for subwoofers in background
and foreground music systems. Extended
low-frequencies bring power and energy to the
music without excessive overall level that can annoy
customers and intrude on conversation. Our system
example uses the new AcousticDesign AD-S28Tw
surface mount subwoofer as well as the AD-C81Tw
ceiling subwoofer. Consider adding subwoofers to
your next high-quality music installation. You and your
customers will thank you for it.
•1
;
<2ПЦ*
К Series
Active Loudspeakers
Entertainers | Musicians | DJs
Concert Systems
The QSC К Series is quite simply The New Standard
in lightweight powered loudspeaker systems and will
satisfy the needs of the most demanding entertainers,
installers and A/V users. QSC's team of amplifier
engineers has created a Class D power module unpar­
alleled in the industry. The series consists of three,
bi-amplified 2-way models ranging in woofer size from
8" to 12" plus a dual 12" subwoofer.
The selection of woofer diameter and coverage for the
various К Series models is not arbitrary but is based
on acoustical science. К Series is designed using a
concept called Directivity Matched Transition™ (DMT™).
DMT matches the high-frequency coverage angle to
the natural coverage of the woofer at crossover
frequency. As a result, frequency response remains far
more uniform across the entire audience area. The K8
delivers wide 105° coverage making it a great choice
for performers who work in more intimate venues
where the audience is closer to the stage and spread
more widely. The more directional K12 with its 75
coverage is a better choice when more "throw"
is needed. The Kl 0, of course strikes a balance
between both width and throw. All models boast
the same 1000 watt power module and the
same high-quality, neodymium HF driver.
Extensive DSP processing is employed throughout,
providing levels of sonic clarity and total output that
exceed expectations for systems of this size and weight.
On-board switches select preset EQ contours. Combo
XLR and 1/4" TRS inputs accept either Microphone or
Line Level input while a set of RCA phono inputs (not
available on KSub) allow additional connectivity to
portable MP3 players, CD players and line-level mixers.
Up to three audio sources can be mixed internally and
summed to a balanced output for "daisy-chaining"
44
of multiple units. Separate direct through-puts are also
provided on each channel for additional flexibility.
Full-range models are housed in rugged ABS enclo­
sures with a professional appearance that is at home
in any application. ABS is a far more robust material
than conventional speaker plastics and offers of
sonic benefits due to its internal rigidity. Ergonomic
aluminum handles and a highly protective steel grille
complete the package for ease of transport and long
term durability. The Kl 2 and K10 enclosures are also
designed for floor monitor use.
The К Series full-range models feature a unique
Tilt-Direct™ pole cup mounting system. A simple turn
of the dial engages a 7.5 degree downward tilt of the
speaker allowing acoustic energy to be kept on the
audience and off reflective surfaces for applications
where maximum coverage from a high-positioned
speaker is desired. Integrated M10 suspension
points allow for suspended applications with a
К Series M10 Kit (sold separately) or Yoke bracket
(sold separately).
The KSub is a dual-12" bandpass design, constructed
of premium birch and includes high-quality, anti-rattle
casters. The subwoofer features a threaded pole
receptacle for a positive, wobble-free connection to
a threaded speaker pole (included).
Remote gain control capability is offered via an
external potentiometer (not included) that may be
wired to the on-board Euroblock connector. In an
installed application, multiple К Series speakers can
be "daisy-chained" for total gain control from a single
remote pot. Auto-standby mode is engaged after 5
minutes of inactivity and disengages instantly when
an audio signal is present.
К8
Kill
KIJ
KSub
System Type
Trapezoidal 2-way
Multipurpose 2-way
Multipurpose 2-way
4th Order Bandpass
Frequency Range (-10 dB)
61 Hz - 20 kHz
56 Hz - 20 kHz
48 Hz - 20 kHz
44 Hz-148 Hz
Frequency Response (-3 dB)
66 Hz-18 kHz
60 Hz-18 kHz
52 H z - 1 8 kHz
48 Hz - 134 Hz
Nominal Coverage (-6 dB)
105° conical
90° conical
75° conical
N/A
Output' (Peak SPL @ 1M)
127 dB
129 dB
131 dB
130 dB
Amplifier Power
1000 W Class D
1000 W Class D
1000 W Class D
1000 W Class D
Current Consumption
1/8 Power'
100 VAC, 2.3 A • 120 VAC, 2.01 A • 230 VAC, 1.13 A
System Performance
Driver Information
LF
HI
8" cone transducer
10" cone transducer
12" cone transducer
2x 12" cone transducers
1.75" diaphragm compression driver
1.75" diaphragm compression driver
1.75" diaphragm compression driver
ч/Л
Controls / Selectors
Power, Gain A, Cain B, Mic/Line, LF Mode (Ext Sub/Norm/DEEP™), HF Mode (Flat/Vocal Boost, Front LED (On/Off/Limit)
Power, Cam, LF Mode (Normal/DEEP™)
Polarity (NormafReverse)
Front LED (On/Off/Limit)
Indicator LEDs
Power, Signal A, Signal B, Standby, Limit, Mic
Power, Signal, Standby, Limit
Signal Connectors
Balanced female XLR/ 1/4" line/mic level input. Balanced female XLR/ 1/4" line level input. Dual Balanced male XLR
full-range line level out. Balanced male XLR "mix" out. Stereo RCA line level input. Remote gain control.
Locking IEC power connector.
Dual balanced lemale XLR/1/4" line level
input. Dual Balanced male XLR full-range
line level out Remote gain control. Locking
IEC power connector.
AC Power Connector
Universal power supply 85 - 265 VAC, 50 - 60 Hz
Dimensions (HWD) inches
17.7" x 11" x 10.6"
20.4" x 12.6" X 11.8"
23.7" X 14" X 14"
26" x 14" x 28.1" (including casters)
Dimensions (HWD) mm
450 mm x 280 mm x 269 mm
519 mm x 320 mm x 300 mm
603 mm x 356 mm x 356 mm
665 mm x 356 mm x 714 mm
Net Weight (each)
27 lb/12.2 kg
32 lb/14.5 kg
41 lb/18.6 kg
74 lb/33.6 kg
/ Calculated lor I m, based on sensitivity (full-space for lull range systems and half-space for LF-only and subwooler systems) and peak power capability ol amplifier.
2 1/8 power и representative ol current draw with typical music program material with occasional clipping.
Features
Available К Series Accessories
Lightweight p o r t a b l e p o w e r e d speakers w i t h legendary QSC
a m p l i f i e r p o w e r a n d reliability.
•
K8 TOTE
•
K12TOTE
lOOO w a t t Class D, b i - a m p l i f i e d p o w e r m o d u l e s in all m o d e l s .
•
K8 YOKE
•
K12YOKE
Extensive DSP e n h a n c e s s y s t e m p e r f o r m a n c e .
•
K I O TOTE
•
KSub COVER
Attractive a n d professional a p p e a r a n c e .
•
K I O YOKE
•
К Series M l О KIT
Rugged ABS e n c l o s u r e s ( K 8 , K I O a n d К 1 2 ) .
Tour-grade 1 8 g a u g e steel grilles.
E r g o n o m i c h a n d l e s w i t h c o m f o r t a b l e , non-slip grip.
3 5 m m p o l e sockets w i t h Tilt-Direct™ (full-range m o d e l s ) .
M l 0 rigging p o i n t s for s u s p e n d e d installation
(full-range m o d e l s ) .
K I O a n d K 1 2 p e r f o r m as m a i n PA or stage m o n i t o r s .
E x t e n s i v e DSP
•
Intrinsic Correction™, first f e a t u r e d i n o u r h i g h - e n d line-array
p r o d u c t s m a p s 6 5 - 7 5 spacially-averaged m e a s u r e m e n t s t o
IIR a n d FIR filters t h a t actively adjust t i m e , f r e q u e n c y a n d
a m p l i t u d e r e s p o n s e t o a m a x i m a l l y flat b a n d p a s s target. T h e
result is a speaker that b e h a v e s e q u a l l y w e l l across t h e e n t i r e
s o u n d field.
•
DEEP™ a n d e x c u r s i o n l i m i t i n g a l l o w for e x t e n d e d l o w f r e q u e n c y r e s p o n s e by actively m a n a g i n g l o w - f r e q u e n c y
transients w i t h o u t d e g r a d a t i o n of t h e u n d e r l y i n g signal or
adjacent f r e q u e n c i e s .
•
CuardRail™ p r o t e c t i o n , first i n t r o d u c e d o n o u r GX Series
amplifiers protects b o t h t h e a m p l i f i e r m o d u l e a n d y o u r
p e r f o r m a n c e f r o m u n n a t u r a l a n d destructive clipping.
4-1
HPR Series
Powered Loudspeakers
Entertainers | Musicians
Concert Systems
DJs
The HPR Series combines the simplicity and versatility
of powered loudspeaker systems with the power,
technology and legendary reliability of QSC amplification. Whether your application is vocal reinforcement,
dance music or full-tilt rock and roll sound, there's an
HPR speaker system for you.
Every HPR model is built around a high-output, reliable
QSC power module using the same top-quality
components and design standards as QSC RMX Series
amplifiers. Unlike powered speakers with low-cost
"chip amps," the HPR Series uses discrete component
designs to deliver the best possible performance even
when pushed to the limit. The power modules incorporate sophisticated signal processing functions
carefully tailored to the loudspeaker system. Each
amplifier channel includes its own limiting with the
parameters individually optimized for the frequency
band. Thick aluminum heat sink extrusions with deep
fins provide mechanical strength and plenty of surface
area to keep the module running cool.
mounting or flying in vertical or horizontal orientation.
A 12" woofer with 3" voice coil and lightweight
neodymium magnet is driven by 400 watts of Class H
power. The 1.4" diaphragm neodymium compression
driver is powered by a 100 watt, class AB+B amplifier
and is loaded on a 75° conical horn. It's the same
high-frequency driver you'll find on the HPR153i
3-way loudspeaker system.
HPR152I
The bi-amplified 15" 2-way HPR152i is a versatile
workhorse, built to handle nearly any sound reinforcement challenge. A high-power woofer with a 3" voice
coil provides low frequency extension down to 47 Hz.
The 1.75" diaphragm compression driver on a 90° x
60° horn delivers smooth high frequencies up to 20
kHz. The power module includes a 100 Hz low-cut
filter for use with subwoofers. Three threaded Ml 0
inserts allow for vertical suspension.
HPR153I
All HPR enclosures are constructed of rugged birch.
Drivers and woofers are protected by a heavy 16
gauge perforated steel grille with a distinctive and
professional appearance. The grille-mounted power
LED can be disabled by means of a rear-panel switch
when desired. The HPR122i, HPR152i and HPR153i
also feature integrated M10 suspension points for
installed applications.
The HPR153i 3-way loudspeaker is a great choice
when the warmth, clarity and projection of a hornloaded mid-range design is desired. The 15" lowfrequency driver provides extension down to 36 Hz
while the 6" mid-range driver seamlessly handles the
critical vocal region. A 1.4" diaphragm compression
driver delivers brilliant top end response. Three
threaded M10 inserts allow for vertical suspension.
HPR122I
1|,
The multipurpose HPR122i performs superbly as a
stage monitor or main PA speaker. Available accessories
mate to the 9 threaded M10 inserts for pole or yoke
O K
IHHRMISBKB. -.••"'"'•.
|W
\ "'
4(.
Wtf
HPHI22I
HPR152I
HPRISJi
HPRlSli
HPRlSli
System Type
12" 2-way multipurpose
15" 2-way full-range
15" 3-way full-range
15" subwoofer
18" subwoofer
Frequency Range (-10 dB)
53 Hz - 22 kHz
47 Hz - 20 kHz
36 Hz - 20 kHz
43 Hz - 145 Hz
39 H z - 140 Hz
Frequency Response (-3 dB)
62 Hz-18 kHz
54 Hz-17.5 kHz
41 Hz - 17.5 kHz
51 Hz-105 Hz
45 Hz - 95 Hz
Nominal Coverage (-6 dB)
75° conical
90° x 60°
90° x 40°
N/A
N/A
Output' (Peak SPL @ 1M)
131 dB
135 dB
133 dB
133 dB
134 dB
Amplifier Power
LF
400 W
400 W
400 W
700 W
700 W
Ml
N/A
N/A
IOOW
N/A
N/A
III
100W
100W
100W
N/A
N/A
1.5 A (0.8 A)
1.5 A (0.8 A)
1.8 A (0.9 A)
2.2 A (1.1 A)
2.5 A (1.3 A)
15" cone transducer, 3" voice coil
15" cone transducer, 3" voice coil
15" cone transducer, 3 voice Kill
15" cone transducer, 3" voice coil
18" cone transducer, 4" voice coil
Ml
N/A
N/A
6.5" horn loaded mid-range
N/A
N/A
HF
1.4" diaphragm compression driver
1.75" diaphragm compression drive
1.4" diaphragm compression driver
N/A
N/A
System Performance
Current Consumption
1/8 Average Power(l20V/230V)
Driver Information
LF
Controls / Selectors
Cain, Low-cut filter, Front LED On/Off, Power, Circuit breaker
Indicator LEDs
Power on, signal present, limiter active
Signal Connectors
Balanced female XLR line level input. Balanced male XLR full-range line level output
AC Power Connector
IEC AC Inlet
IEC AC Inlet
Hi /V InH
IEC AC Inlet
IEC AC Inlet
Dimensions (HWD) inches
26.9" x 14.7" x 14.9"
33.6" x 19.1" x 17.9"
45.1" X 19.1" x 17.9"
25.6" X 22" x 20.75"
28.6" X 23.5" x 22.9"
Dimensions (HWD) mm
683 mm x 373 mm x 379 mm
853 mm x 485 mm x 455 mm
1144 mm x 485 mm x 455 mm
651 mm x 559 mm x 525 mm
727 mm x 597 mm x 582 mm
Net Weight (each)
60 lb/27.2 kg
100 lb/45.5 kg
118 l b / 5 4 kg
98 lb/44.5 kg
127 l b / 5 8 kg
Balanced female XLR line level inputs x 2 (L+R)
Balanced male XLR full-range line level through puts x 2 (L+R)
Balanced male XLR low-cut line level outputs x2 (L+R)
/ Calculated for I m, based on sensitivity (full-space for full range systems and hall-space for LF-only and subwoofer systems) and peak power capability at amplifier
2 1/8 power is representative of current draw with typical music program material with occasional clipping.
HPR151i | HPR181i Subwoofers
The HPR Series subwoofers supply the extended low
frequency response required for dance music, bass
instruments and kick drums. Both HPR subwoofers
use a 700 W QSC amplifier. Flexible input signal
processing and connectivity allow configuration of
systems consisting of a single sub with two mid-high
speakers, or larger systems employing multiple
subwoofers. The signal processing includes a stereo
electronic crossover with XLR line-level outputs for
connection to any powered two- or three-way midhigh speaker. A top-mounted, 35 mm pole socket is
provided for mounting a mid-high speaker, and heavyduty 3" casters on the HPR181i facilitate load-in.
The HPR181 i subwoofer uses a
single 18" low-frequency speaker
with a 4" voice coil. It produces
134 dB SPL peak (at 1 m) with
frequency response down to 39
Hz. The HPR181 i offers truly
impressive, uncompromising lowfrequency response and output.
Available HPR Accessories
HPR COVER 1 2 2
HPR COVER 1 5 2
HPR COVER 1 5 3
HPR COVER 1 5 1
HPR COVER 1 8 1
The compact HPR151 i subwoofer uses a single
15" low-frequency driver. It produces 133 dB SPL
peak (at 1 m) with frequency response down to 43
Hz. The HPR 151 i subwoofer's tight, punchy sound
quality rivals many 18" subwoofers.
HPR POLE 2 6
HPR POLE 3 1
HPR YOKE 1 2 2
HPR M l О KIT
HPR SUSPENSION KIT 1 2 2
47
I-82H
System Type
ici|iiniiy Rainy
(-10 dB)
Frequency Response
(-6dB)
Nominal Coverage
Compact 2-way,
jrorte^enclqsure
60 Hz - 22 kHz
80 Hz-21 kHz
90°H x 60°V (rotatable)
1-282H
Compact 2-way,
ported enclosure
60 Hz - 29.5 kHz
I Hz - 27.7 kHz
90°H x 60°V (rotatable)
Power Capacity'/ Sensitivity'/ Peak SPL'
Full Range
ISIS Series Loudspeakers
Entertainers | Musicians | DJs
Concert Systems
240W(8hrs)/90.5dB/120dB
450W(8hrs)/93dB/126dB
Driver Information
LF
8" high power treated
paper cone, 2" voice coil,
neodymium magnet
8" high power treated
paper cone x 2,2" voice coil,
Driver Information
HF
1" exit compression driver
I" exit compression driver,
1.7" voice coil
Input Connectors
NL4 in parallel x 2
NL4 in parallel x 2
Suspension / Attachment Point
Yol<e m o u n t о р 1 ю п а
Y o k e т о и п 1 , p o l e m o u n t socl<et
'' Р * m c u n t
'
socket mike stand adapter induded mike stand adapter induded
iJinielMonwHWIII
inches
Dimensions (HWD)
mm
17.4" x 10" x 11.2"
26.17" x 11.44" x 10.21"
442.0 mm x 254 mm
x 284.5 mm
X /!." I
Net Weight (each)
17.5 lb/7.9 kg
28.5 lb/12.9 kg
I-82H
The QSC I-82H is an 8", 2-way, full-range loudspeaker
that is well suited to applications in which low to
moderate levels and very high-quality sound reinforce­
ment are required. With the ability to be pole and mic
stand mounted, truss mounted, or used as a floor
monitor/stage fill, these injection molded speakers
are an excellent choice for musicians, mobile enter­
tainers, and others needing a high-quality, lightweight
SR package that sounds great, is visually unobtrusive,
and is easy to transport.
The I-82H enclosure incorporates an 8" weatherproof,
LF transducer and a 1" exit HF compression driver.
Dynamic Protection circuitry is included in the network
to protect the HF driver from overload damage. The
HF driver is coupled with QSCs unique Advanced
Directivity™ rotatable waveguide - enabling the loud­
speaker to deliver well-controlled coverage, regardless
of its orientation.
An ideal solution for a variety of mobile SR applica­
tions, the I-82H includes a pole cup bracket for pole
mount applications as well as a 5/8"-27 mic stand
adapter. With the addition of QSCs optional I-YM8
Yoke Mount/Floor Monitor Kit, the I-82H can be hori­
zontally pole mounted for pan and tilt aiming or used
as a floor monitor. For truss mounting, the I-YM8
accepts most industry standard truss clamps.
I-82H Accessories Included
•
Pole cup bracket
•
Mic stand adapter
561 mm x 686 mm
/ Continuous IEC specified test signal, 2 hours unless otherwise stated
2 Based on nominal impedance, measured in full space. I [email protected] I m.
3 Calculated using specified power capacity and system sensitivity.
6 dB peak-to-average signal ratio assumed.
I-282H
The QSC I-282H is a dual 8",
2-way, full-range loudspeaker
that is well suited to applica­
tions in which moderate levels
and very high-quality sound
reinforcement are required. Pole mounted, truss
mounted, or used as a floor monitor/stage fill, these
injection molded speakers are an excellent choice for
musicians, mobile entertainers, and anyone else
needing a high-quality, lightweight SR package that
sounds superb, is visually unobtrusive, and with its
built-in handles, is easy to transport.
The I-282H enclosure incorporates two 8" weather
resistant, LF transducers and a 1" exit HF compression
driver. Bi-amplified or full-range operation may be
selected by means of a rear-panel switch. The HF
driver is coupled with QSCs unique Advanced
Directivity™ rotatable waveguide — enabling the loud­
speaker to deliver well-controlled coverage, regardless
of its orientation.
An ideal solution for a variety of mobile SR applica­
tions, the I-282H includes a cup for pole mounting.
By using the included yoke mount with swivel exten­
sion feet, the 1-282-H can be vertically or horizontally
mounted for pan and tilt focusing or used as a floor
monitor. For truss mounting, the yoke accepts most
industry standard truss clamps.
Optional I-82H Accessories
I-282H Accessories Included
•
11' ч ••• Ivi 1 Ml ]M I l l i l f i l i ' l
I-YM8 Yoke M o u n t / F l o o r M o n i t o r Kit
•
Yoke Mount
1;Я!Н
/ " V 9 Mixed Sources
FSC
recycled wood o> fibre
This catalog is printed with Forest Stewardship Council certified paper and printing,
SSiKSJ.i^rtSUJSS!»""
using low VOC biodegradable soy inks and U.S. made paper.
please recycle
ш
%
051409 ©2009 QSC Audio Products, LLC. All rights reserved. QSC, the QSC logo, PowerLight, WideLine, Q-Sys, QSControl.net and BASIS are registered trademarks of QSC Audio Products,
LLC, in the US and other countries. GuardRail, DEEP, DMT, ModularDesign, AcousticDesign, IntelliDock, Advanced Directivity, Advanced Thermal Management and Intrinsic Correction are
trademarks of QSC Audio Products, LLC. CobraNet is a trademark of Cirrus Logic. Speakon and PowerCon are trademarks of Neutrik. All trademarks are the property of their respective
owners. Multiple aperture diffraction slot waveguide US Patent number 7177437. Other patents may apply or be pending.
шшшшшшт
qscaudio.com
1-800-854-4079 or 714-957-7100
Outside the U.S. +1-714-754-6175
Fax: 714-754-6174
QSC Audio Products, LLC
1675 MacArthur Boulevard
Costa Mesa, CA 92626
ГУ РосНИИИТ и АП
Федеральный информационный фонд отечественных и
иностранных каталогов на промышленную продукцию
Каталог был представлен на выставке
NAMM musik messe RUSSIA-2012
(Международная выставка музыкальной индустрии)
Каталог включен в базу данных
«Федерального информационного фонда
отечественных и иностранных каталогов на
промышленную продукцию»
Россия,105679, Москва, Измайловское шоссе, 44,
Тел./факс (495)366-5200. e-mail:; fkatalog(a),mail.ru, www. ritap.ru
Электронная копия издания изготовлена с целью её включения в базы
данных Федерального информационного фонда отечественных и
иностранных каталогов на промышленную продукцию, которые
формируются в соответствии с Постановлением Правительства РФ от 24
июля 1997 г. № 950 и Постановлением Правительства РФ от 31 декабря 1999
г. № 2172-р и зарегистрированы Комитетом по политике информатизации
при Президенте РФ под №№ 39-50.
2012 год
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement