Heavy Duty Station

Heavy Duty Station
www.jbctools.com
Heavy Duty Station
Ref. HD-B
Safety
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When removing it, hold the plug, not the wire.
- Do not work on electrically live parts. Antistatic handle of soldering irons is electrically conductive.
- The tool should be placed in the stand when not in use in order to activate the sleep mode. The
soldering tip, the metal part of the tool and the stand may still be hot even when the station is turned
off. Handle with care, including when adjusting the stand position.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite even when out of
sight.
- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working
to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance. Maintenance shall not be carried out by children
unless supervised.
2
w w w.jbctools.com
Packing List
The following items should be included:
HD-1B / 2B / 9B
Control Unit
HD-SD
Stand
T470-A
Handpiece with
screw
POWER CORD
CL9885
Tip Cleaning Stand
S0354
Sponge
0011283
Connection cable 1m
MANUAL
w w w.jbctools.com
Heavy Duty station
Ref. hD-B
3
Features
USB-B connector to PC:
- Update station software
- Create graphs of the soldering process
- Manage and monitor parameters via PC
Power Cord Socket
Equipotential connector
ATTENTION:
We strongly recommend tigthening screw
firmly to avoid cartridge from moving
4
w w w.jbctools.com
HD-SD STAND
Cable collector
Keeps working area free of cable
Quick tip changer
The cartridge extractor system
permits switching cartridges
without the need to interrupt
your work
Adjustable tool holder
The tool stand are easily adjustable
5
T470-A handpiece with screw
These handpieces has been specially designed for intensive desoldering jobs with high power
requirements such as soldering components to large grounds planes, production of solar
panels, armor and other applications.
It incorporates a screw for securing the cartridges.
Use C470 Cartridge range.
ACCESSORIES
F6457 Fume Extractor (not included)
Easily clips onto the handpiece and can be quickly removed for easy
maintenance.
CONNECTABLE HANDPIECES
T470-SA* Handpiece with screw + long cable (3m)
T470-ZA* Tri-lobed Handpiece with screw
3-sided handle for easy grip.
T470-FA* Comfort Handpiece with screw
It incorporates a foamed grip of insulating material which
makes you feel more comfortable when working
T470-MA* Comfort Handpiece
with screw + long cable (3m)
*These handpieces only work with C470 cartridge range for this station.
6
w w w.jbctools.com
Changing cartridges
1 Untighten the screw before placing the handpiece in the cartridge extractor.
2 Place the handpiece in the extractor and
pull o remove the cartridge.
3 Place the handpiece on top of the new
cartridge, press slightly down and remove the handpiece from the extractor.
Alignment
Important.
You must insert the cartridge
till the end for a good connection.
Use the mark
as reference.
4 Once the cartridge is properly inserted we recommend tightening the screw firmly
to avoid cartridge from moving.
7
cl9885 tip cleaning stand
Is designed to be used next to the point of work. With its weight and non-slip base it can be
used without having to hold the base down while cleaning the tips.
CL6210
Brass Wool
S0354 Sponge
CL6210 Brass wool
CL6205 Inox wool
CL6220 Brushes
S0354 Sponge
CL0236 Wiper
optional
CL6205 Inox Wool
CL6220 Brushes
TT-A Tip-Tinner
cl0236 Tip wiper
Tapping
8
Wipping
Wiper can be easily removed to clean it.
w w w.jbctools.com
Control display
Selected temp. 3 5 0 o C
350 c
0
Tip temperature
Power 10%
% Instant power
supplied to the tool
Decrease &
move down
Access Menu &
Confirm Selection
Increase &
move up
settings menu
Main menu
Original PIN: 0105
Station settings
1
2
3
4
Temp unit
Maximum temp
Minimum temp
Help text
5 Beep
6 Change PIN
Back
Tool settings
Celsius
4000C
2000C
OFF
ON
1 Fix one temp
----2 Temp levels set
OFF
3 Sleep delay
0 min
1
2
3
Exit
Reset settings
Station settings
Tool settings
4
5
Counters
Program version
Counters
1 Plugged hours
2 Working hours
3 Sleep hours
0
0
0
4 Hibernation hours
5 No tool hours
6 Sleep cycles
0
0
0
Tool 470
4 Sleep temp
1800C
5 Hibernation delay 30 min
6 Temp adjust
+ o oC
Back
Tool 470
Back
9
Heat Management
JBC stations intelligently manage the tool temperature and it helps to extend the tip life:
Expected life
(hours)* 700
600
500
400
300
200
100
0
Temp (ºC)
200
225
Sleep
Temp
250
275
300
325
350
375
400
425
450
Working
Temp
Work mode: Lift tool from the stand and the tool tip heats up to the selected temperature.
Sleep mode: When the tool is in the stand, the temperature reduces (preset sleep temperature is
180ºC / 360ºF).
Hibernation mode: After longer periods of inactivity (pre-set to 30 minutes), the power is cut off
and the tool cools down to room temperature.
Heat management increase tip life which reduces cost of ownership.
10
w w w.jbctools.com
Maintenance
Before carrying out maintenance or storage,
always unplug the equipment from the mains.and
let it cool down.
Clean periodically
- Use a damp cloth to clean the case and the
tool. Alcohol can be used only to clean the
metal parts.
- Check periodically that the metal parts of the
tool/stand are clean. Use a glass cleaner
or a damp cloth to clean the station screen.
- Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation.
Rusty and dirty surfaces reduce heat transfer to the solder joint.
- Replace the fuse if it is blown according to the following guidelines:
Remove the fuse by pulling the black cap.
Help yourself with a lever tool if necessary.
Place the new fuse into the holder by pushing
and enter it again into the station.
- Replace any defective or damaged piece. Use original JBC spare parts only.
- Repairs should be performed only by a JBC authorized technical service.
11
Specifications
-
-
-
-
-
-
-
-
Total weight: 5.9 kg (13.1 lb)
Temperature selection from 90°C (190°F) to 500°C (932°F).
Output Peak Power: 250W
Safety transformer, mains separator and double isolation.
HD-2B 230V 50/60Hz. Input fuse: 2A. Output: 47V. Control Unit model: HD-2B
HD-1B 120V 50/60Hz. Input fuse: 4A. Output: 47V. Control Unit model: HD-1B
HD-9B 100V 50/60Hz. Input fuse: 4A. Output: 47V. Control Unit model: HD-9B
Ambient operating temp: 10-40 ºC / 50-104 ºF
USB station-PC
Complies with CE standards
ESD protected housing “skin effect”
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
www.jbctools.com
0013989-0614
Warranty
JBC’s 2 year warranty covers this equipment
against all manufacturing defects, including the
replacement of defective parts and labour.
Warranty does not cover product wear due to use
or mis-use.
In order for the warranty to be valid, equipment
must be returned, postage paid, to the dealer
where it was purchased.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement