ALCATEL-LUCENT OMNIACCESS

110 SERIES ACCESS POINTS

OPTIMIZE CLIENT PERFORMANCE IN

HIGH-DENSITY WI-FI ENVIRONMENTS

The multifunctional and affordable Alcatel-Lucent OmniAccess™ 110 series wireless access points (APs) maximize mobile device performance in high-density Wi-Fi® environments while minimizing interference from Long Term Evolution (LTE) cellular networks.

These high-performance 802.11n APs deliver wireless data rates up to 450

Mb/s per radio and employ three spatial streams to support 50 percent more throughput and mobile devices than previous generation APs.

The AP115 and IAP115 APs feature a 2.4-

GHz and a 5-GHz radio, each with 3x3:3 multiple-input multiple-output (MIMO), and three integrated omnidirectional downtilt antennas. The AP114 and IAP114 models feature the same radios with three combined and diplexed external antenna connectors.

FEATURES

Advanced Cellular Coexistence

(ACC)

The 110 series ACC feature minimizes interference from 3G/4G LTE networks, distributed antenna systems and commercial small cell/femto cell equipment.

ClientMatch

While users roam, ClientMatch™ eliminates the sticky client behavior by continuously gathering the session performance metrics from mobile devices. If a mobile device moves out of range of an AP, or if radio frequency (RF) interference impedes performance, ClientMatch automatically steers the device to a better AP.

Adaptive Radio Management (ARM)

ARM manages the 2.4-GHz and 5-GHz radio bands to optimize Wi-Fi client performance and to ensure that APs stay clear of RF interference. ARM also provides the best-in-class RF management, which is essential to creating the most reliable, high-performance wireless LANs

(WLANs).

BENEFITS

• The 110 series ACC feature enables

Alcatel-Lucent WLANs to perform at peak efficiency by minimizing interference with

3G/4G networks.

• Wi-Fi client performance and the WLAN network performance are optimized by eliminating sticky client behavior.

The 110 series can be configured to provide part-time or dedicated air monitoring for spectrum analysis and wireless intrusion protection, virtual private network

(VPN) tunnels to extend remote locations to corporate resources, and wireless mesh connections where Ethernet drops are not available.

Operating modes

The 110 series of APs offer a choice of operating modes to meet unique management and deployment requirements.

• Controller-managed mode. When managed by OmniAccess controllers, 110 series

APs offer centralized configuration, data encryption, policy enforcement and network services, as well as distributed and centralized traffic forwarding.

• Alcatel-Lucent Instant™ mode. In

Instant mode, a single AP automatically distributes the network configuration to other Instant APs in the WLAN. Simply power up one Instant AP, configure it over the air, and plug in the other APs — the entire process takes about five minutes.

If WLAN and network requirements change, a built-in migration path allows

110 series Instant APs to become part of a WLAN that is centrally managed by a mobility controller.

• 802.11a/b/g/n controllerless Instant AP

• 802.11a/b/g/n mobility controller managed AP

• Remote AP (RAP)

• Spectrum analysis identifies sources of

RF interference

• Air monitor provides wireless intrusion protection

• Hybrid AP serves Wi-Fi clients and provides wireless intrusion protection and spectrum analysis

• Secure enterprise mesh

Security

• With an OpenDNS service subscription

OmniAccess Instant RAPs deliver integrated web filtering, malware and botnet protection to every device connected to the WLAN.

• Integrated Trusted Platform Module (TPM) for secure storage of credentials and keys

• SecureJack-capable for secure tunneling of wired Ethernet traffic

Wireless radio specifications

• AP type: Indoor, dual radio, 5 GHz and

2.4 GHz 802.11n 3x3:3

• Software-configurable dual radio supports

5 GHz (Radio 0) and 2.4 GHz (Radio 1)

• 3x3 MIMO with three spatial streams and up to 450 Mb/s wireless data rate

• Supported frequency bands (countryspecific restrictions apply):

¬ 2.4000 GHz to 2.4835 GHz

¬ 5.150 GHz to 5.250 GHz

¬ 5.250 GHz to 5.350 GHz

¬ 5.470 GHz to 5.725 GHz

¬ 5.725 GHz to 5.850 GHz

• Available channels: Dependent on configured regulatory domain

• Dynamic frequency selection (DFS) optimizes the use of available RF spectrum

• Supported radio technologies:

¬ 802.11b: Direct sequence spread spectrum (DSSS)

¬ 802.11a/g/n: Orthogonal frequency division multiplexing (OFDM)

• Supported modulation types:

¬ 802.11b: BPSK, QPSK, CCK

¬ 802.11a/g/n: BPSK, QPSK, 16 QAM,

64 QAM

• Transmit power: Configurable in increments of 0.5 dBm

• Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):

¬ 2.4 GHz band: +28 dBm (23 dBm per chain)

¬ 5 GHz band: +25 dBm (20 dBm per chain)

• ACC minimizes interference from

LTE cellular networks

• Maximum ratio combining (MRC) for improved receiver performance

• Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance

• Short guard interval for 20 MHz and

40 MHz channels

• Space-time block coding (STBC) for increased range and improved reception

• Low-density parity check (LDPC) for high-efficiency error correction and increased throughput

• Supported data rates (Mb/s):

¬ 802.11b: 1, 2, 5.5, 11

¬ 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54

¬ 802.11n: 6.5 to 450 (MCS0 to MCS23)

• 802.11n high-throughput (HT) support:

HT 20/40

• 802.11n packet aggregation: A-MPDU,

A-MSDU

Power

• Maximum power consumption: 13 W, plus up to 2.5 W for attached USB device

• Power sources sold separately

• Direct DC source: 12 V DC nominal, +/-5%

• Power over Ethernet (PoE): 48 V DC

(nominal) 802.3af or 802.3at-compliant source

¬ USB host port is disabled when using an 802.3af PoE power source. For unrestricted operation with PoE power, use an 802.3at-compliant source.

Antennas

• OAW-AP114: Three RP-SMA connectors for external dual-band antennas. Internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 1.5 dB in 2.4 GHz and 2.5 dB in 5 GHz

• OAW-AP115: Six integrated omnidirectional down-tilt antennas for

3x3 MIMO with maximum antenna gain of 4.5 dBi in 2.4 GHz and 5.5 dBi in 5 GHz.

Built-in antennas are optimized for horizontal ceiling mounted orientation of AP115.

Other interfaces

• 10/100/1000Base-T Ethernet network interface (RJ-45)

¬ Auto-sensing link speed and medium dependent interface/medium dependent interface crossover (MDI/MDIX)

¬ 802.3az Energy Efficient Ethernet (EEE)

¬ PoE-PD: 48 V DC 802.3af PoE or 802.3at

PoE+

• DC power interface, accepts 1.7/4.0 mm center-positive circular plug with 9.5 mm length

• USB 2.0 host interface (Type A connector)

• Serial console interface (RJ-45, TTL levels)

• Visual indicators (LEDs):

¬ Power/system status

¬ Ethernet link status (ENET)

¬ Radio status (2x; RAD0, RAD1)

• Kensington security slot

• Reset button

Mounting

• Included with AP:

¬ Mounting brackets (2) for attaching to

9/16 in. or 15/16 in. T-bar drop-tile ceiling

• Optional mounting kits:

¬ OAW-AP220-MNTC2: OmniAccess™

AP220 Series Access Point Mount Kit

(ceiling grid) contains 2x ceiling grid rail adapters (for Interlude and Silhouette style rails).

¬ OAW-AP220-MNTW1: OmniAccess

AP220 Series Access Point Mount Kit

(basic, flat surface) contains 1x flat surface wall/ceiling mount bracket.

¬ OAW-AP220-MNTW2: OmniAccess

AP220 Series Access Point Mount Kit

(box style, secure, flat surface) contains

1x flat surface wall/ceiling secure mount cradle.

Alcatel-Lucent OmniAccess 110 Series Access Points

ALCATEL-LUCENT ENTERPRISE DATA SHEET

2

Mechanical

• Dimensions/weight (unit, excluding mount accessories):

¬ W x D x H: 180 mm x 180 mm x 45 mm

(7.09 in. x 7.09 in. x 1.77 in.)

¬ 650 g (1.43 lb)

• Dimensions/weight (shipping):

¬ W x D x H: 220 mm x 225 mm x 55 mm

(8.66 in. x 8.86 in. x 2.17 in.)

¬ 880 g (1.94 lb)

Regulatory

• FCC/Industry of Canada

• CE Mark

• R&TTE Directive 1995/5/EC

• Low Voltage Directive 72/23/EEC

• EN 300 328

• EN 301 489

• EN 301 893

• UL/IEC/EN 60950

• EN 60601-1-1, EN60601-1-2

Environmental

• Operating:

¬ Temperature: 0°C to +50°C

(32°F to +122°F)

¬ Humidity: 5% to 95% non-condensing

• Storage and transportation temperature range:

¬ -40°C to +70°C (-40°F to +158°F)

For more country-specific regulatory information and approvals, please see your Alcatel-Lucent representative.

Regulator model numbers

• OAW-AP114 and OAW-IAP114: APIN0114

• OAW-AP115 and OAW-IAP115: APIN0115

Certifications

• CB Scheme Safety, cTUVus

• UL2043 plenum rating

• Wi-Fi Alliance (WFA) certified

802.11a/b/

Warranty

• Limited lifetime warranty

Minimum software versions

• AOS-W 6.3.1.0

• InstantOS™ 4.0.0.0

Table 1. RF performance

MAX. TRANSMIT POWER PER

TRANSMIT CHAIN (DBM)

2.4 GHZ

RECEIVE SENSITIVITY PER

TRANSMIT CHAIN (DBM)

802.11B

1 Mb/s

11 Mb/s

23

23

-97

-88

MAX. TRANSMIT POWER PER

TRANSMIT CHAIN (DBM)

5 GHZ

RECEIVE SENSITIVITY PER

TRANSMIT CHAIN (DBM)

—

—

—

—

802.11A/G

6 Mb/s

54 Mb/s

802.11N HT20

MCS0/8/16

MCS7/15/23

802.11N HT40

MCS0/8/16

MCS7/15/23

21

18

20

16

20

16

-93

-76

-93

-73

-90

-69

20

16

19

14

19

14

-92

-74

-92

-71

-88

-67

Maximum capability of the hardware provided. Maximum transmit power is limited by local regulatory settings. RF performance numbers for the AP114 are slightly lower due to additional internal RF circuitry.

Alcatel-Lucent OmniAccess 110 Series Access Points

ALCATEL-LUCENT ENTERPRISE DATA SHEET

3

Figure 1. AP115 antenna pattern plots a. Horizontal or azimuth plane (top view)

270

300

285

315

330

345

-5

-10

-15

-20

-25

-30

-35

-40

5

0

0

X

0

Y

30

255

240

225

210

195

45

180

165

150

135

60

75

90

105

120

2.450 1

2.450 2

2.450 3

2.450 GHz b. Elevation plane (side view)

270

300

285

315

330

345

-5

-10

-15

-20

-25

-30

-35

-40

5

0

0

0

30

45

60

75

Y

90

255

240

225

210

195

Z

180

165

150

135

105

120

2.450 1

2.450 2

2.450 3

2.450 GHz

270

300

285

315

330

345

-5

-10

-15

-20

-25

-30

-35

-40

5

0

0

X

0

30

45

60

75

Y

90

255

240

225

210

195

180

165

150

135

105

120

2.450 1

2.450 2

2.450 3

5.550 GHz

270

300

285

315

330

345

-5

-10

-15

-20

-25

-30

-35

-40

5

0

0

0

30

45

60

75

Y

90

255

240

225

210

195

Z

180

165

150

135

105

120

2.450 1

2.450 2

2.450 3

5.550 GHz

Alcatel-Lucent OmniAccess 110 Series Access Points

ALCATEL-LUCENT ENTERPRISE DATA SHEET

4

ORDERING INFORMATION

PART NUMBER

110 SERIES APS

OAW-AP114

DESCRIPTION

OAW-IAP114

OAW-IAP114-US

OAW-IAP114-IS

OAW-IAP114-JP

OAW-AP115

OAW-IAP115

OAW-IAP115-US

OAW-IAP115-IS

OAW-IAP115-JP

OmniAccess AP114 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11‘B/G/N’ and 802.11‘A/N’ operation, RP-SMA external antenna connectivity, 1 x

10/100/1000Base-T (RJ-45) Ethernet interface (supports 802.3af PoE or 802.3at PoE+), 1 x 12 V DC power interface, security slot

OmniAccess Instant AP114 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11‘B/G/N’ and 802.11‘A/N’ operation, RP-SMA external antenna connectivity, 1 x

10/100/1000Base-T (RJ-45) Ethernet interface (supports 802.3af PoE or 802.3at PoE+), 1 x 12 V DC power interface, security slot. Rest of the world (not to be used in the United States, Japan, or Israel)

OmniAccess Instant AP114 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11‘B/G/N’ and 802.11‘A/N’ operation, RP-SMA external antenna connectivity, 1 x

10/100/1000Base-T (RJ-45) Ethernet interface (supports 802.3af PoE or 802.3at PoE+), 1 x 12 V DC power interface, security slot. Restricted regulatory domain: United States

OmniAccess Instant AP114 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11’B/G/N’ and 802.11’A/N’ operation, RP-SMA external antenna connectivity, 1 x

10/100/1000Base-T (RJ-45) Ethernet Interface (Supports 802.3af POE or 802.3at POE+), 1 x 12V DC power interface, Security slot. Restricted regulatory domain: Israel.

OmniAccess Instant AP114 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11’B/G/N’ and 802.11’A/N’ operation, RP-SMA external antenna connectivity, 1 x

10/100/1000Base-T (RJ-45) Ethernet Interface (Supports 802.3af POE or 802.3at POE+), 1 x 12V DC power interface, Security slot. Restricted regulatory domain: Japan.

OmniAccess AP115 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11‘B/G/N’ and 802.11‘A/N’ operation, dual-band integral antenna, 1 x 10/100/1000Base-T

(RJ-45) Ethernet interface (supports 802.3af PoE or 802.3at PoE+), 1 x 12 V DC power interface, security slot

OmniAccess Instant AP115 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11‘B/G/N’ and 802.11‘A/N’ operation, dual-band integral antenna, 1 x 10/100/1000Base-T

(RJ-45) Ethernet interface (supports 802.3af PoE or 802.3at PoE+), 1 x 12 V DC power interface, security slot.

Rest of the world (not to be used in the United States, Japan, or Israel)

OmniAccess Instant AP115 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11‘B/G/N’ and 802.11‘A/N’ operation, dual-band integral antenna, 1 x 10/100/1000Base-T

(RJ-45) Ethernet interface (supports 802.3af PoE or 802.3at PoE+), 1 x 12 V DC power interface, security slot.

Restricted regulatory domain: United States

OmniAccess Instant AP115 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11’B/G/N’ and 802.11’A/N’ operation, dual-band integral antenna, 1 x 10/100/1000Base-T

(RJ-45) Ethernet Interface (Supports 802.3af POE or 802.3at POE+), 1 x 12V DC power interface, Security slot.

Restricted regulatory domain: Israel.

OmniAccess Instant AP115 wireless access point. Dual radio 3x3:3 IEEE 802.11a/b/g/n wireless access point with support for 802.11’B/G/N’ and 802.11’A/N’ operation, dual-band integral antenna, 1 x 10/100/1000Base-T

(RJ-45) Ethernet Interface (Supports 802.3af POE or 802.3at POE+), 1 x 12V DC power interface, Security slot.

Restricted regulatory domain: Japan.

MOUNTING ACCESSORIES

OAW-AP220-MNTC2

OAW-AP220-MNTW1

OAW-AP220-MNTW2

OmniAccess AP220 Series Access Point Mount Kit (ceiling grid). Contains 2x ceiling grid rail adapters

(for Interlude and Silhouette style rails)

OmniAccess AP220 Series Access Point Mount Kit (basic, flat surface). Contains 1x flat surface wall/ceiling mount bracket

OmniAccess AP220 Series Access Point Mount Kit (box style, secure, flat surface). Contains 1x flat surface wall/ ceiling secure mount cradle

GENERIC INDOOR AP ACCESSORIES

OAW-AP-AC-UN Universal AC Power Adapter Kit for OmniAccess APs and IAPs For North America, Japan, United Kingdom, Italy,

EC (Shuko), Australia, China, India, and Korea

OAW-AP-AC-12V18

OAW-MS-3501G

PD-9001GR-AC

OmniAccess 12 V DC/18 W AC power adapter for compatible indoor AP models. Does not include country-specific power cord

1-port 802.3af PoE Midspan 10/100/1000 15.4 W. No power cord included

Antennas

OAW WLAN 1-port 802.3at PoE Midspan 10/100/1000 30 W. U.S. power cord included. Rest of the world – all power cords must be ordered separately.

Go to the Alcatel-Lucent website for information on antenna part numbers.

enterprise.alcatel-lucent.com

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of

Alcatel-Lucent. All other trademarks are the property of their respective owners. The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.

Copyright © 2014 Alcatel-Lucent. All rights reserved. 201411170012EN (November)