Owners Manual - North Canterbury Equipment

Owners Manual - North Canterbury Equipment
Owners Manual
Renovator MkIII
Seed Drill
From Serial Number 071731
Head Office:
P.O. Box 2018
Hilton Highway, Washdyke
Timaru, New Zealand
Telephone (03) 688 2029
Facsimile (03) 688 2821
Australian Branch:
4B Silverton Close
Laverton North 3026
Melbourne, Australia
Telephone (03) 9314-9666
Facsimile (03) 9314-6810
Pt. No. 67354
Issue 0207
Renovator
Contents
Page
Introduction
Acquisition & Warranty
Disclaimer
Description of Machine
Specification
SAFETY - General
......................................
2
......................................
2
......................................
2
Working Principle . . . . . . . . . . . . . . . . . . . . . . .
3
......................................
3
Transport
Operation
Safety Symbols on Machine . . . . . . . . . . . . . . 4
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . 5
Be Prepared for Emergencies . . . . . . . . . . . . . 5
Appropriate Dress . . . . . . . . . . . . . . . . . . . . . . 6
Transport This Machine Safely . . . . . . . . . . . . 6
Handle Agricultural Chemicals Safely . . . . . . . 7
Avoid High Pressure Fluids . . . . . . . . . . . . . . . 7
Safe Work Practices . . . . . . . . . . . . . . . . . . . . 7
Practise Safe Maintenance . . . . . . . . . . . . . . . 8
Hazard Points . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety Decals & Safety Guards . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sowing Chart
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SAFETY - Machine Specific
Basic Calibration Procedure
Gearbox Setting Lever . . . . . . . . . . . . . . . . . .
Setting Seeder Shutter Slides . . . . . . . . . . . . .
Bottom Flap Settings . . . . . . . . . . . . . . . . . . . .
Seed Calibration . . . . . . . . . . . . . . . . . . . . . . .
Recalculating the Constant . . . . . . . . . . . . . . .
Use of Seed Rate Calculator . . . . . . . . . . . . . .
Calibration Deviations . . . . . . . . . . . . . . . . . . .
Sowing of Fine Seeds . . . . . . . . . . . . . . . . . . .
Sowing Small Seeds . . . . . . . . . . . . . . . . . . . .
Sowing Peas . . . . . . . . . . . . . . . . . . . . . . . . . .
Hectaremeter Settings . . . . . . . . . . . . . . . . . . .
Calibration Notes . . . . . . . . . . . . . . . . . . . . . . .
16
16
16
17
19
19
20
21
22
22
23
25
Maintenance & Care
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lubrication Instructions . . . . . . . . . . . . . . . . . .
Maintenance Schedule . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Notes . . . . . . . . . . . . . . . . . . . . .
26
27
28
30
31
Parts List
Base Machine . . . . . . . . . . . . . . . . . . . . . . . . . 33
Optional Extras . . . . . . . . . . . . . . . . . . . . . . . . 66
1
Pt. No. 67354
Issue 0207
Introduction
Acquisition & Warranty
On delivery of your new Duncan Renovator please check that
the machine is not damaged. In cases of shipping damage,
please ask your dealer to arrange for the appropriate claim to
be lodged immediately. Assemble any parts supplied loose and
inspect your machine with the aid of this manual to familiarise
yourself with its features. If you have any queries ask your
dealer straight away. The machine is covered by our 12 month
warranty on faulty parts, subject to normal use.
Record below the serial number of your machine and keep
it in a secure place to help trace the machine and assist
us when you order parts.
Model: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Owner: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.............................................
.............................................
Delivery Date: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dealer: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.............................................
.............................................
The Owner’s Manual
Your new Duncan Renovator will give long and efficient service
if given normal care and operated properly.
This owner’s manual is provided so that you can become
thoroughly familiar with the design of the machine and to
furnish information on correct operation, adjustment and
maintenance. Only persons well acquainted with these
guidelines should be allowed to use the equipment.
A separate illustrated parts section has been provided so that if
any parts are required your dealer will be able to supply them
by reference to part numbers.
The manual is considered as part of your machine and must
remain with the machine when it is sold.
Right and left hand references in this manual are determined
by standing behind the machine and facing in the direction
of travel.
2
Disclaimer
Every effort has been made to
ensure that the information in this
manual was accurate and up to
date at the time of going to press.
Clough Agriculture reserves the
right to make subsequent changes
to the machine, where necessary,
without notification.
The Company will not be
responsible for any damage or
consequential loss arising out of
misinterpretation or failure to follow
recommended procedures. Nor will
it be liable for any damage caused
by or arising out of modification or
misuse of its product.
The owner has a responsibility to
protect himself and others by
observing all safety information
and by ensuring all operators are
well acquainted with the safety
information, trained in the correct
use of the machine and applying
safe work practices.
Description of Machine
The Duncan ‘Renovator’ is a Coil Tyne Tee-boot drill.
The box is mounted on a robust frame accommodating
large diameter tyres for the arable situation. The ground
engaging components are controlled by a hydraulic ram
and rocker arm system, giving ample control on ground
pressure, good transport clearance and contour following
ability. Sowing depth is controlled by adjusting the
hydraulic ram as required. The quality European type
peg roller seeder system handles all seeds from turnip
and rape through to peas and maize. The seeders are
driven from the groundwheels via a jockey wheel system
and variable speed gearbox. For transport the drive is
easily disconnected by raising the drill to its transport
height.
Working Principle
The gearbox, pegged seed rollers and seeder flaps are
set to give the desired seed rate. The coil tyne and teeboot, create the seed bed. Seed flows down the flexible
tubes between seeder and tee-boot units, and drops
into the prepared seed bed.
Specification
Dimensions & Capacities
Drill Model
*Weights are approximate and include
dual box machine and optional disc
openers only.
Width (Over Wheels)
Overall Length
Height (Groundwheels Up)
Height (Groundwheels Down)
Weight (Unladen)
Groundwheels Tyre Size
Tyre Pressures
Maximum Speed
Jockey Tyre Size
Jockey Tyre Pressure
Row Spacing
Sowing Width
Box Capacity (litres) per box
Small Box Capacity (litres)
Table 1
19 Run
23 Run
3026mm
3616mm
3512mm
3512mm
1700mm
1700mm
2035mm
2035mm
1610kg*
1850kg*
10/80-12
2.4 bar (35psi)
30km/hr
410/350 x 6 x 4ply
2.76 bar (40psi)
147.5mm
147.5mm
2800mm
3390mm
348 litres
437 litres
103 litres
130 litres
Pt. No. 67354
Issue 0207
3
!
ATTENTION
On the machine important safety information is indicated by these symbols.
These highlight general safety aspects in regard to the machine rather than specific hazards.
Do not ride or allow passengers on the machine.
Under no circumstances are passengers to be permitted on
the machine while it is in operation or being transported. Any
footboards and/or footsteps are provided solely for the
purpose of preparing the machine for use.
Keep clothing and body extremities well clear of pinch
points while the machine is operating (seeding or
calibrating). Keep well clear of moving parts at all times.
These signs typically occur wherever trapping points exist.
These include drive chains, sprockets, shafts, wheels, discs,
pivot points, etc. Guards are provided with the machine for
safety reasons (where practical without compromising
machine performance). Ensure these are always fitted during
operation.
Always exercise extreme caution in the vicinity of sharp
edges and points.
Where possible guards are provided with the machine for
safety reasons (where practical without compromising
machine performance). Ensure these are always fitted during
operation.
Footboards, footsteps, drawbars and other machine
surfaces may be slippery when wet.
Apply extra caution in wet conditions and in the early morning
when surfaces are wet.
Keep Clear. (It is dangerous to be in this area when the
machine is operating.)
4
SAFETY - General
N.B. Throughout this
manual important safety
information is indicated
by these symbols in the
margin:
A prohibition should
be observed under all
circumstances.
A warning indicates a
hazard that could
cause death or injury if
the warning is ignored.
A caution indicates a
hazard that may cause
damage to property if
the caution is ignored.
This section of the manual offers general guidelines
for the safe operation of machinery. It does not replace
local safety regulations. These guidelines were current at
the time of publication, but may be superseded by later
regulations.
Clough Agriculture has made every effort to highlight all
risks to personnel or property. Owners and operators have
a responsibility to exercise care and safe work practices at
all times in the vicinity of the machine.
Owners are advised to keep up to date on safety issues
and to communicate these to all users of the machine.
Contact the Occupational Safety and Health Service
(OSH) for further information about general safety aspects.
If you have safety concerns specifically related to this
machine, contact your dealer immediately.
Operator Safety
Read this manual carefully before operating new
equipment. Learn how to use this machine safely.
Be thoroughly familiar with the controls and the proper use
of the equipment before using it.
Take careful note of all safety instructions both in this
manual and on the machine itself. Failure to comply with
instructions could result in personal injury and/or damage
to the machine.
Replace missing or damaged safety signs on the machine
and ensure that these remain clearly visible.
It is the owner’s responsibility to ensure that anyone
who operates, adjusts, lubricates, maintains, cleans or
uses the machine in any way has had suitable
instruction and is familiar with the information in this
manual (particularly with regard to safety aspects).
Operators and other users of the machine should be
aware of potential hazards and operating limitations.
Be Prepared for Emergencies
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors, ambulance,
hospital and fire department near your telephone.
Pt. No. 67354
Issue 0207
5
SAFETY - General (Continued)
Appropriate Dress
Wear close fitting clothing and avoid rings or other forms of
jewellery which could become caught in the machinery.
People with long hair must have it securely fixed and confined
close to the head.
Refer to local safety standards for protective clothing and
recommended safety equipment.
Transport This Machine Safely
Ensure that all linkage pins and security clips are fitted correctly.
With trailing machines tow with the drawbar only, as this is the
only safe towing point on the machine.
Always check that bystanders (especially children) are well clear
(front and rear) before starting and moving the tractor and the
machine.
Plan safe routes of travel, and be aware of power lines and
other roadside hazards. Take particular care when towing
implements on hillsides.
Do not ride or allow passengers on the machine.
This machine is not designed to carry passengers, and no riders
are permitted.
Road transport
On public roads,
• A speed of 40km/h must not be exceeded.
• Do not operate during the hours of darkness unless standard
lights are fitted and clearly visible. (This also applies when
visibility is limited, e.g., in foggy conditions.)
See the guidelines in the Vehicle Dimensions and Mass Rule,
issued by the Land & Transport Safety Authority.
Avoid tip-overs
Avoid holes, ditches and obstructions which may cause the
machine to tip over, especially on hillsides. Never drive near the
edge of a gully or steep embankment - it might cave in. Slow
down for hillsides, rough ground and sharp turns.
6
SAFETY - General (Continued)
Handle Agricultural Chemicals Safely
All farm chemicals should be stored, used, handled and
disposed of safely and in accordance with the
supplier’s/manufacturer’s recommendations.
Read the product label before using, noting any warnings
or special cautions, including any protective clothing or
equipment that may be required, ie. respirtor.
Do not eat or smoke while handling sprays, fertilisers, coated
seeds, etc. Afterwards, always wash your hands and face
before you eat, drink, smoke, or use the toilet.
Store sprays, fertilisers, coated seeds, etc. out of reach of
children and pets, and away from food and animal feeds.
Any symptoms of illness during or after using chemicals
should be treated according to the supplier’s/manufacturer’s
recommendations. If severe, call a physician or get the
patient to hospital immediately. Keep the container and/or
label for reference.
Avoid High Pressure Fluids
Avoid any contact with fluids leaking under pressure, because
the fluids can penetrate the skin surface.
Any fluid which penetrates the skin, will need to be removed
immediately by a medical expert. Seek specialist advice on
this type of injury.
Relieve the pressure before disconnecting any hydraulic or
other lines. Make all repairs and tighten all fittings before
re-connection to pressurised fluid.
Keep your hands and body away from any pinholes or high
pressure jets. Search for leaks with a piece of cardboard
instead of using your hand directly.
Safe Work Practices
All farm machinery is potentially dangerous and should be
treated with caution and respect.
Before starting the machine, ensure that all controls are placed
in neutral and that bystanders are well clear. Check that the
guards have been securely fitted and that any adjustments
have been made correctly.
Where possible, disconnect or isolate the drive mechanism to
the implement. Lower the machine onto the ground when not
in use.
Pt. No. 67354
Issue 0207
7
SAFETY - General (Continued)
Practise Safe Maintenance
Keep the machine in safe working condition. Routine
maintenance and regular servicing will help reduce risks and
prolong the life of the machine.
General Maintenance
Accidents occur most frequently during servicing and repair.
The following general rules must be followed when maintaining
or working with machinery:
• All operating and maintenance manuals must be
read before and referred to while using or servicing any
piece ofequipment.
• Turn off all machinery power sources and isolate the
machine before making adjustments, doing lubrication,
repairs or any other maintenance on the machine.
• Ensure that the machine hydraulics are disconnected from
the power source.
• Wear gloves when handling components with cutting
edges, such as any ground cutting components.
• Beware of hazards created by springs under tension
or compression when dismantling or maintaining the
machine.
• It is recommended that you clean the machine with a water
blaster or similar apparatus before commencing
maintenance.
Make Sure the Machine is Well Supported
When machinery is fitted with hydraulics, do not rely on the
hydraulics to support the machine. During maintenance or while
making adjustments under the machine, always lock the
hydraulics and support the machine securely. Place blocks or
other stable supports under elevated parts before working on
these.
Electrical Maintenance
Disconnect the electrical supply from the tractor before doing
any electrical maintenance.
Welding
With electronic equipment in modern tractors it is advisable to
disconnect the machine from the tractor, or at least disconnect
the alternator and battery before attempting any welding.
Use Only Genuine Spare Parts
Unauthorised modifications or non-genuine spare parts may be
hazardous and impair the safe operation and working life of the
machine.
Excess lubricants must be disposed of safely so as not to
become a hazard.
8
SAFETY - Machine Specific
This section of the manual gives specific guidelines for
the safe operation of the Renovator.
These guidelines were current at the time of publication, but
may be superseded by later circumstances. They do not
necessarily cover every possible hazard and must be read in
conjunction with the SAFETY - General section (Page 4 - 8).
Hazard Points on the Renovator
The lists below are not all-inclusive and serve only to highlight
the more obvious areas of risk.
The decals attached to the machine are a general reminder
that there are hazardous areas on the machine, rather than
specifically highlighting all possible hazards.
For decal locations on machine, refer Page 11.
No Ride
Passengers are not permitted anywhere on the machine.
Pinch Points/Moving Parts
Hazardous areas include:
• Drive chains.
• Sprockets between the drive wheel, the transfer shaft and
the gearbox (RH side).
• Sprockets between the gearbox and the box shafts
(RH side).
• Agitator drive units (LH side).
• Agitator shaft inside the boxes.
• Seeder units, box shaft and shaft connectors.
• Wheel legs and main frame assemblies
• Between discs and other sub-assembly parts (where fitted).
• Press wheel assemblies (where fitted).
Slippery When Wet
Hazardous areas include:
• Footboards and footstep.
• All smooth surfaces on the frame structure.
Keep Clear
Hazardous areas include:
• Between the tractor and Renovator.
• Immediately adjacent to the Renovator side.
Pt. No. 67354
Issue 0207
9
SAFETY - Machine Specific
(Continued)
Hazard Points on the Renovator
(Continued)
Pedestal Chain Guards
To prevent hands, etc. getting caught in drive chains, guards
are provided to cover sprockets, chain and chain tensioners
mounted about the drive pedestal (RHS). These guards must
be fitted while using the machine.
Warning: Access to pinch points is still possible from
underneath the guard.
For guard locations on machine, refer Page 11.
Calibrating
Be particularly careful when calibrating the seeding rate. At
this time, the calibration trays have been removed and are no
longer covering the rotating seeder units. See Pinch
Points/Moving Parts (Page 9) for hazardous areas.
Transport
The two wheels located at the sides of the machine are for the
purpose of controlling sowing depth. These are also used to
support the machine weight during transport (while linked to
the tractor).
Important - Refer to safety cautions in the Transport section,
page 12 of the manual. Ensure that all linkage pins and
security clips are fitted correctly.
Maintenance
Refer Page 26 for reference to the Maintenance and Care
section of the manual.
Lubrication
Refer Page 27 for reference to the Maintenance and Care
section of the manual.
10
SAFETY - Machine Specific
(Continued)
1
Safety Decals
& Safety Guards
2
5
3
Inside Box Lid
1
1
6
4
3
2
2
8
7
Item Decal/Guard
1
2
3
4
5
6
6
7
8
4
Cross Reference Pt No
‘No Ride’
‘Pinch Point/Moving Parts’
‘Slippery When Wet’
‘Keep Clear’
Arrows
Pedestal Drive Guard (Dual box machine)
Pedestal Drive Guard (Single box machine)
Jockey Drive Swing Guard
‘40 km/hr’
Refer
Refer
Refer
Refer
Page
Page
Page
Page
9
9
9
9
Refer Page 10 & 34
Refer Page 10 & 36
Refer Page 10 & 54
43900
43901
43902
43904
43905
25995
25996
25745
43912
Qty
3
4
2
2
4
1
1
1
2
Table 2
Pt. No. 67354
Issue 0207
11
Transport
1
Raise the drill into the transport position and hold at the full
extent of the rams for a few seconds to allow cylinders to
rephase/equalise.
2
Important - To avoid machine damage due to drill
lowering during transport, always close the hydraulic valve
on the drawbar. Move the handle to a position at 900 to the
hydraulic line as shown in Fig 1. This applies to the
drawbar and disc opener hydraulic valves where fitted.
Fig 1
3
Locate jack stand in transport position, if fitted. Refer Fig 2.
4
Ensure lighting and oversize warning requirements meet
recommendations published by the local Land Transport
Authority or equivalent.
5
Maximum towing speed 40 km/hr.
For countries other than New Zeaand greater speed
restrictions may apply, please refer to your local
transport authority.
Ensure towing vehicle requirements are adequate for the
towed vehicle e.g. mass, brakes. Refer to
recommendations published by the local Land Transport
Authority or equivalent.
Fig 2
Braking when towing can cause the load to jackknife. Use
extra care when towing in adverse conditions such as mud,
inclines and sharp bends.
Lower towing speeds are recommmended on farm
roads/tracks and where one wheel is on or over a road
verge.
6
Attach safety chains to tractor. Refer Fig 3.
Safety chains must be crossed over underneath the
coupling and attached to the towing vehicle. The
attachment points must be as close as practical to the
towing coupling and one each side.The towbar on the
towing vehicle must be rated for the towed mass. Do not
remove or replace the safety chains provided with any
other than those specified in the parts manual.
Note: The safety chains are provided with sufficient length
to cater for all towing vehicles. Safety chains must be
shortened by cutting off excess length so that if the
coupling fails the drawbar will not hit the ground.
7
If the machine is fitted with row markers or other vertical
extensions, check clearance under power lines en route.
8
Important - For greater disc opener ground clearance,
adjust the ram or turnbuckle on the disc opener unit so
they are at maximum height, and/or extend the drawbar
ram or turnbuckle to level the machine chassis.
Fig 3
12
Operation
General Operation Guidelines
1
Use a sufficiently powerful tractor which is heavy enough
to tow the drill safely.
2
Operate the drill at a speed of 6-12 km/hr (4-8 mph).
In stoney and uneven ground conditions a lower speed is
more appropriate
3
Check that the drill is level during calibration and while seeding.
4
Check tyre pressure before seeding. Refer page 3.
5
Double check seed rates before seeding.
6
Ensure wheel hydraulics are in float during seeding.
7
Raise the drill out of the ground when making any turns.
8
Raise the drill out of the ground before backing up.
9
After prolonged storage, check to see that all drive
mechanisms and hydraulic equipment are functioning correctly.
Check that the seed tubes are not perished or blocked.
Sowing Speed
Typical travel speeds when sowing range from 6-12 km/hr in
good conditions. In stoney and uneven ground conditions a
lower speed is recommended to minimise rapid part
deterioration. Sowing too fast can result in:
1 Poor contour following and uneven sowing depth.
2 Impact damage to:
a Ground engaging components.
b Bearings, housings & axles.
c Fasteners & structural components.
3 More extreme conditions will result in greater vibration
and uneven seed flow at low seeding rates.
Sowing Depth Control
The sowing depth is dependent on:
1 The wheel height in relation to the chassis
2 Tyre pressure
3 Ground condition i.e. hard or soft
1
The wheel height in relation to the chassis is controlled using
the threaded depth adjustment collar (1) on the non-drive
shaft. Refer Fig 4.
Caution: Do not overextend the thread depth adjustment
collar. Additional collars may be required.
Fig 4
Pt. No. 67354
Issue 0207
13
Level Drill
Use the drawbar turnbuckle or ram to tilt the drill so it is
sitting level. An adjustment may be required after a short
period of use because the paint wears off the discs and the
discs sharpen which in turn improves the penetration
abilities.
Transport Position
When in the transport position the hydraulic cylinders are
fully extended. In this position the cylinders fully equalise
by allowing oil to bypass the master cylinder piston. It is
recommended to raise the drill into the transport position
when turning at headlands or regularly to counteract the
effects of oil leakage past the piston and ensure cylinder
rods are equally extended and minimise variations in
sowing depth.
Coulter Penetration Depth
To create the ideal seed bed the disc opener coulter
should cut approximately 20mm below the inverted tee
point. In hard and dry conditions this may not be
achievable, and better machine/sowing performance may
be achieved without using the disc openers. An indication
of this will be the machine bouncing which will result in
uneven sowing depth.
Coulters will give better penetration ability as they sharpen
with use.
Press Wheels
1
2
Press wheels are used to compact the soil after sowing to
give good seed/soil contact. The downward pressure of the
press wheels can be adjusted for different ground
conditions, eg. a greater pressure may be best suited to
harder and drier conditions while less pressure is required
for cultivated soils. To increase the downward pressure
adjust the M10 nuts (1) to increase the spring precompression. Ensure the two nuts are locked together
tightly. The maximum pre-compression is 40mm. Excessive
spring pre-compression will restrict maximum height travel
and may lead to component damage.
To sow without using the press wheels remove the
transport pin (2), lift the press wheel and relocate the
transport pin in the alternative hole. Refer Fig 5.
Fig 5
14
Renovator Seed Drill Sowing Chart
Position
gW
he
rin
Seed Rate (kg/ha)
Gearbox Setting Position
Me
te
tto
m
Fla
Sli
de
Bo
tio
*
utt
er
Ra
H/L
Sh
ar
Ge
Test Seed Type/
Thousand Seed
Wgt., TSW*(gm)
p*
*
Table 3
el*
High & Low Ratio - Row Spacing 147.5
Type
Wheat (41.2)
Oats (37.2)
Barley (45.7)
Ryecorn (25.8)
White Peas (302)
Green Peas (240)
Peren. Grass (2.27)
Annual Grass (4.4)
Pasture Mix* ( - )
Lucerne (3.17)
Turnip (2.17)
H
H
H
H
H
H
H
H
H
H
L
3/4
Full
Full
3/4
3/4
3/4
Full
Full
Full
3/4
3/4
3
3
3
3
3
3
3
3
3
1
1
N
N
N
N
N
N
N
N
N
F
F
Kale (3.20)
Swedes (3.25)
Rape (3.50)
White Clover (1.11)
Red Clover (2.23)
Super Phosphate
DAP Granules
Super Phosphate
DAP Granules
L
L
L
L
L
H
H
L
L
3/4
3/4
3/4
3/4
3/4
Full
Full
Full
Full
1
1
1
1
1
3
3
3
3
F
F
F
F
F
N
N
N
N
15
20
30
40
50
60
70
80
Hints
90
100
102.14 128.78 152.36 180.03 208.25 234.35
98.98 122.97 146.37 171.74 196.99 219.56
117.66 144.97 176.33 205.4 236.51 266.22
118.96 148.03 178.5 207.32 240.85 270.94
111.97 161.93 213.44 246.59 305.11 358.66 397.42 457.22
Agitator Stopped
77.62 116.89 156.06 192.65 230.78 272.72 316.2 355.73
6.53
13.73
27.41
40.90
53.86
67.23
8.06
16.32
31.75
46.31
60.67
76.68
13.92
27.59
41.31
54.42
67.38
81.65
9.27
13.82
17.97
22.43
26.38
1.76
3.21
4.63
6.0
Agitator Stopped
1.69
3.21
4.66
6.02
Agitator Stopped
1.62
3.0
4.44
5.78
1.57
3.06
4.47
5.65
1.90
3.56
5.05
6.66
0.96
0.94
0.82
81.51
Agitator Stopped
Agitator Stopped
1.65
Agitator Stopped
Agitator Stopped
8.17
Agitator Stopped
9.75
91.51 140.12 185.26 235.37 286.62 344.51 397.16 456.96
174.04 214.2 256.66 301.67 346.42 382.88
53.7
71.0
90.24 109.84 132.03 152.25 182.99
115.64 132.81 146.77
Gear Ratio*: H, High = 21T on Transfer Shaft,
13T on Gearbox Input Shaft.
L, Low = 13T on Transfer Shaft,
21T on Gearbox Input Shaft.
Shutter Slide*: For Grain, changing the Shutter Slide from 3/4 to Full gives
10% to 15% more flow.
Pasture Mix*: Test Mixture = 72% Perennial Grass, 8% White Clover,
8% Cocksfoot, 8% Concord, 4% Red Clover
Bottom Flap*: The values shown were the optimum test settings,
decreasing the gap may cause seed damage, too large a gap will give
intermittent flow rates. (Flaps are spring loaded to cope with small
variations in seed/granule size).
Metering Wheel*: N = Normal Metering Wheel
F = Fine Seed Metering Wheel
TSW*:
TSW(gm) x Desired Plants/m2 = Sowing Rate (Kg/Ha)
Germination %
Notes
1.Where a small seeds box is used,
multiply the above seed rates by 0.80 to
account for the different gearing ratio.
2.Seed rates shown are approximate only
for the respective gearbox setting. It is
recommended that the calibration
procedure is always used. Refer to
page 16.
Pt. No. 67354
Issue 0207
15
Basic Calibration Procedure
1
Gearbox Setting Lever
To set the seed rate at the gearbox, slacken the star knob (1) by
turning counter-clockwise and push from below into the position
indicated in the Sowing Chart. Retighten the star knob firmly
(Fig 6).
Important
The settings shown in the Sowing Charts (kg/ha) can only serve
as reference values. Deviations may occur caused by
differences in the size, shape, density of the grain and by the
dressing agent. Therefore prior to any sowing, always carry
out calibration trials to accurately determine the actual seed
rate.
Fig 6
Using the stepless variable speed gearbox, the speed of the
metering shaft and thus the seed rate is set steplessly. The
higher the figure indicated on the scale by the setting lever the
greater the seed rate (Fig 6).
Selecting the Gear Ratio
The Seed Drill is designed with a two speed (high and low) gear
ratio arrangement where the moving of the chain from a 21 x 13
teeth ratio to a 13 x 21 teeth ratio changes the output from high
to low (Fig 7). The selection and method for changing the ratio is
detailed under Speed Setting Page 21.
Fig 7
Setting Seeder Shutter Slides
The varying flow properties of seeds require different shutter
slide positions which may be found in the Sowing Chart for the
individual type of seed. This corresponds to one of the three
settings in Fig 8.
Fig 8/A
Fig 8/B
Fig 8/C
Closed
3/4 Open
Fully Open
A
B
C
Table 4
Fig 8
Bottom Flap Settings
10
1
10
The various seed sizes require matching bottom flap clearances
below the metering wheel. The adjusting plate allows for 10
different settings. The required position for the seed type may be
found in the Sowing Chart. The control levers are located on the
LH end of the seedbox, (opposite end to the gearbox).
Number “1” corresponds to the minimum (closed) position and
“10” the maximum gap (Fig 9).
Fig 9
16
Basic Calibration Procedure
(Continued)
Seed Calibration
1
The calibration test should be done to confirm the required
seed rate and is done with the drill stationary and level.
Seed Calibration Procedures
2
Fig 10
1
Fig 11
1
Remove the calibration tray from the storage brackets
on the seedbox. Place the calibration tray (1) on the
support members below the seeders (Fig 10).
2
Position all the clear plastic seed diverters (2) to
redirect the seed into the calibration tray (Fig 10).
3
Make sure all the shutters are open and set to the
position indicated in the seed charts for the particular
seed (Table 3. Page 15).
4
Agitator Shaft - Check the Seed Chart “Hints” (Table 3)
whether to connect or disconnect the shaft by removing
the lynch pins (1) during seeding (Fig 11).
5
For the test, half fill the box with seed. If this is not
possible make sure the seed is evenly distributed within
the box.
6
For setting method refer to Basic Calibration Procedures
(Page 16).
Note For seeds which are not covered in the Sowing Chart
(Page 15), use the figures for a seed of comparable size
and shape.
Fig 12
7
Place the crank handle over the hexagonal drive dog on
the transfer shaft and turn anti-clockwise until the seed
flows consistently from the seeders (Fig 12). To ensure
complete filling of the seed unit continue turning the
crank until the calibration tray is approximately half full
then empty into the seedbox. The drill is now ready for
calibration.
8
Turn the crank handle anti-clockwise the required
number of revolutions as detailed in Table 5.
Note The Calibration is usually done for 1/40th hectare.
For very small seed rates or when using inaccurate
scales (i.e. unable to measure to the nearest gram) the
calculation based on 1/10th hectare should be used.
Scales must be accurate to 2 grams as any error
will be multiplied by either 10 or 40 giving
inaccurate calibration results.
Pt. No. 67354
Issue 0207
17
Seed Calibration Procedures (Continued)
Hand Crank Turns for Seed Rate Calibration
The tables represented below are for arable conditions (worked
ground) and are calculated to indicate an average situation. If
there is any doubt as to the accuracy of these figures for the
conditions, it is advisable to run at least 1 of the 2 checks on the
calibration figures listed. Refer Page 19 (Recalculating the
Constant) and/or Page 20, (Wheel Slip Deviations). Check and
record which tyres are fitted to your drill, to ensure use of the
correct Hand Crank Turn and Constant figures.
Machine
Size
19 Run
23 Run
Sowing
Width(m)
2.80
3.39
Turns for
1/40 Hectare
32.5
27
Turns for
1/10 Hectare
130
107.5
Table 5
9
Weigh the seed collected during the test in kilograms.
Caution: Scales must be accurate to 2 grams, as any error will be
multiplied by either 10 or 40, giving inaccurate calibration results.
10 Calculate the seed rate by multiplying the kgs previously collected
x 40 (1/40th ha method, refer Table 6) or x 10 (1/10th ha method,
refer Table 7) depending on the requirement. If the resultant
calculation does not produce the desired seed rate use the
enclosed seed rate calculator disc to determine the correct
gearbox setting.
Refer Use of Seed Rate Calculator Page 19.
Suggestion: To be on the safe side and until confidence has been
gained with the method of calibration it is advisable to conduct a
second test at the newly determined gearbox setting.
11 Where a coated seed is used it is advisable to check the
calibration after 1 hectare as dressings can tend to create a
coating on the seed metering wheels thus changing the the
flowing properties of the seed which in turn alters the seed rate.
For 1/40 Hectare (250m2) Calibration
Seed Rate = Actual Seed Collected (kg) x 40
Table 6
For 1/10 Hectare (1000m2) Calibration
Seed Rate = Actual Seed Collected (kg) x 10
Table 7
18
Basic Calibration Procedure (Continued)
Recalculating the Constant
It is especially important in arable situations to check the rolling circumference of the tyre
when in the cultivated area to be sown, and if necessary, to recalculate the constant and
hence the number of crank turns.
If there is a significant difference between the figure used for calculations in this manual, the
constant should be recalculated and hence the crank turns for those particular conditions.
Note: If a significant difference is found in the rolling circumference the H1 setting should also
be adjusted on the hectaremeter.
1
To recalculate the constant due to altered conditions or specific requirements use the
formulae detailed in Table 6 or 7 (Page 18).
2
To obtain the rolling circumference of the tyre:
Half fill the seed/fertiliser boxes or simulate this
loading. Mark the tyre of the drill at 900 to the
ground and the point of contact with a mark
on the ground. Move the drill forward 5
revolutions until the mark on the tyre is
again at 900 to the ground. Measure
the distance along the ground and
divide by 5 to give the rolling
circumference of the tyre.
Use of Seed Rate
Calculator
Determining the gear box
scale setting using the
calculator.
Usually the first calibration test yields a
different seed rate. However with the
value determined from the first test it is
possible to determine the correct gearbox
setting with the aid of the enclosed disc
calculator (Fig 13). The disc calculator consists of 3
scales. An outer white scale (1) for all seed rates above
30 kg/ha and an inner scale (2) for all seed rates below 30 kg/ha.
On the middle coloured scale (3) are all the gearbox setting numbers to a maximum value of
100.
Fig 13
Setting Example (Desired Seed Rate 125kg/ha)
1
2
3
4
From the calibration procedure at a gearbox lever setting of “70”, a seed rate of 175 kg/ha
is obtained.
Turn the inner disc until the measured seed rate of 175kg/ha (A) is in line with the related
actual gearbox setting of “70”(B) (Fig 13).
Read off from the disc rule the necessary gearbox setting for the required seed rate of
125kg/ha (C). In this example the correct setting is “50” (D) (Fig 13).
To be on the safe side the new gearbox setting can be checked by another calibration test.
Pt. No. 67354
Issue 0207
19
Basic Calibration Procedure
(Continued)
Calibration Deviations
Deviations Between the Calibration Test and the
Actual Seed Rate
The most frequent cause for changes between the calibration
test and the seed rate lies in the flowing properties of seed
during sowing. These changes in properties generally result from
reactions of the dressing agents to temperature, humidity or
abrasion. These changes will become even more obvious when
the bottom flaps are incorrectly set. If the setting of these flaps
leaves too large a gap an uncontrollable additional flow of seed
can occur during seeding; especially when assisted by the drill
bouncing, a condition not simulated while conducting the
calibration tests. For this reason the basic setting of the bottom
flaps should be checked at regular intervals.
Residues from the seed dressing on the bottom flaps and
metering wheels can also influence the flowing properties of the
seed and thus the seed rate. In such cases a balance will occur
only after a period of time and it is recommended to repeat the
calibration test to confirm the seed rate after 2-3 seedbox fillings,
nominally when the seed box is half empty. Only then will a
balance occur and the seed rate will stabilise.
Wheel Slip Deviations
It is always possible with rubber tyred drills in extreme ground
conditions to get wheel slip. Not normally a problem with cleated
type tyres in good condition, but more so in the arable situation
with the less agressive tread patterns. The result: large
differences between the calibration test and the actual sowing
rate, obviously less seed deposited than required. The number
of crank turns indicated in Table 5 is correct in most
circumstances other than those mentioned above.
To check number of crank turns for calibration
Should you require to check this in a practical way proceed as
follows:
For an area of 125m2 (1/40 Hectare), a travel distance of
89.2m for 19R machine or 73.7m for 23R machine, place the
crank handle over the hexagonal drive dog on the gearbox.
Move the machine forward over the measured distance,
counting the number of turns of the crank handle as you go.
Using this number of crank turns repeat the calibration.
20
Hints for Sowing with Variable Speed
Gearbox
2
The gearbox allows for stepless changes in the speed of
the metering shaft and thus the seed rates. Due to the
variations in seed type and application rates there are two
speed ranges available.
By changing from High Speed to Low Speed the range of
settings and control is dramatically increased.
Change to the Low Speed when the gearbox setting is
down to 10 on the scale and the desired seed rate cannot
be obtained.
To change the speed setting from high to low, remove the
wing nut (1) and chain cover.(2) (Fig 14).
Release the tension on the chain (1) by forcing back the
chain tensioner (2) and hold in place with the crank
handle. Refer Figure 15. Remove the chain from the 21
tooth output sprocket to the 13 tooth sprocket, then
remove the chain from the 13 tooth gearbox sprocket to
the 21 tooth. Check the chain is correctly aligned then
release the chain tensioner. Ensure the tension roller is
correctly aligned with the chain. Replace guard and
calibrate as required.
1
Fig 14
Low Speed Shown
1
2
To Determine the Gearbox Setting after a
Speed Change
For determining the correct gearbox setting after the speed
change, conduct the first test at 50. With the weight of
seed collected find your correct setting with the aid of the
disc calculator, refer Page 19, Fig 13.
21T
13T
Fig 15
3
1
Sowing of Fine Seeds
For sowing fine seeds the Renovator Drill is equipped as
standard with a combined normal and fine seed “Elite”
metering wheel (1). During grain sowing and other larger
varieties of seed both the normal and fine seed metering
wheels are coupled and both rotate. In order to convert the
seed drill to sow fine seed insert the crank handle and rotate
clockwise until the holes (2) of the fine seed wheel are
visible (Fig 16)
Using the tool supplied (1) disengage the the pin inside
the hole so that the normal metering wheel rotates freely
on the metering shaft (Fig 17).
At this time it would be advisable to close any shutter
slides not required for the fine seed sowing.
When seed is to be sown again using the
normal metering wheel press the pin, from the
normal metering wheel side (opposite direction
to before), using the tool, back into the hole of
the fine seed wheel thus reconnecting the drive
between the two.
1
2
Fig 16
1
Fig 17
Pt. No. 67354
Issue 0207
21
Small Seeds
Calibration with Disconnected Agitator Shaft
The fine seed metering wheel used in Duncan Drills is
especially well suited for sowing small seeds such as rape.
Due to the intensive action caused by the agitator the seeds
can adhere to each other, or be damaged, causing irregular
sowing/germination. Therefore it is recommended that
when sowing small seeds, especially oil seeds and thin
shelled seeds, the drive to the agitator is disconnected.
To do this remove the lynch pin (1) (Fig 18).
Fig 18
1
Deviations between the calibrated and actual seed rate can
occur when residual dressing agent sticks to the bottom flaps
and thus slows the flow of seed. Before beginning the actual
calibration test fill the calibration trays by turning the crank
handle at a high speed around the 90 setting on the gearbox
scale. This will cause an immediate buildup of the dresssing
agent on the flaps. Return the contents of the calibration trays
to the seed box and proceed with the actual calibration. Due
to the residue buildup on the flaps your calibration will now
reflect accurately the required seed rate.
It is advisable with small seeds to use the 1/10 hectare
method for your calibration, thus cutting down on weighing
errors.
Note - Remember to reconnect the agitator shaft as required
for other seeds otherwise the consistency of seed rate will be
affected.
Fig 19
Sowing Peas
Peas having the size and shape as illustrated in Fig 19 (e.g.
White Field Peas), can be sown without problems with all
Clough Drills with this type of metering wheel.
The flap should be set to a gap of at least “3” on the flap
setting lever (Page 16, Fig 9).
With these peas it should not be necessary to run the agitator
shaft.
Peas having the size and shape as illustrated in Fig 20 (e.g.
Green or Garden Peas), tend to bridge inside the seedbox
and do not flow freely.
This multi-faceted pea requires agitation for sowing.
Fig 20
Caution - When resetting the metering wheels
on the seeder shaft
Care should be taken when tightening the grub screws
on the fine seed wheel (Page 21, Fig 16, item 3). Adjust the
grubscrew until the movement of the metering wheel just
stops, then tighten no more than 1/8 of a turn.
Do not overtighten as this can result in breakages while
operating and may render the warranty on these units void.
22
Hectaremeter Settings Setup
Refer to the installation and operation instructions supplied with
your hectaremeter kit (1) for information on installation, calibration,
operation and servicing (Fig 21).
Table 6 gives the effective working widths for the various
machines depending on the machine size and the row spacing.
The calibration procedure described in the hectaremeter
handbook involves accurately measuring the circumference of the
tyre and entering and storing this value in the meter. The effective
sowing width also needs to be entered. For measuring the tyre
circumference and obtaining the rolling circumference of the tyre
refer Recalculating the Constant (Page 19).
Note: If under certain operating conditions a calibration check
indicates a significant difference in the rolling circumference of the
tyre, the hectaremeter should be recalibrated by changing the H1
setting for the period of operation under those conditions.
1
Fig 21
Sowing Width
Machine Size
19 Run
23 Run
Row Spacing (mm)
147.5
147.5
Effective Working Width (m)
2.80
3.39
Table 8
Pt. No. 67354
Issue 0207
23
Hectaremeter Settings (Continued)
Example 1 :
Computronics 1100 Area Meter Setup for MkIII Renovator
(Referring to Sowing Width Table Page 24)
19 Run Machine x 147.5mm Spacings = 2.80m Sowing Width
23 Run Machine x 147.5mm Spacings = 3.39m Sowing Width
Drive Ratio From Wheel to Sensor = 0.7377
Rolling Circumference of Tyre = 2.028m (Refer Page 20)
Circumference of Tyre
Drive Ratio
2.028
=
0.7377
H1 - Distance per Pulse =
= 2.750m
Therefore:
and
H1 Setting = 2750mm
H2 Setting = 2.80metres
= 3.39metres
Distance Travelled per Pulse
Effective Sowing Width 19R
Effective Sowing Width 23R
Please record here the settings for your machine in case you
are required to re-enter them at some time in the future.
H1
H2
It is advisable as with all things electronic to have a backup of your totals. We suggest you
record these on a daily basis in a notebook or diary.
24
Renovator
Calibration Notes
Pt. No. 67354
Issue 0207
25
Maintenance & Care
General Safety and Accident Prevention Advice
1
Make sure that if the tractor remains attached to the drill
that the ignition key is removed.
2
During maintenance the drill should be supported in such a
manner that if hydraulic failure was to occur the machine
would still be adequately supported.
3
Wear gloves when handling components with cutting
edges such as worn discs etc...
4
Disconnect the electrical supply from the tractor before
doing any electrical maintenance.
5
Refer to safety sections for more safety information.
General Cautionary Maintenance Advice
1
Electric Welding - With the electronic equipment in
modern tractors it is advisable to completely disconnect the
implement from the tractor, or at the very least disconnect
the alternator before attempting any welding.
2
Hydraulics - Ensure hydraulic couplings (male & female)
are clean before connecting. Dirty couplings will result in
hydraulic oil contamination and hydraulic cylinder seal
damage and bore scores. This in turn will result in oil
leakage past the piston seals.
No filter is fitted to the hydraulic system. If hydraulic fittings
and oil supply are not going to be kept clean it is
recommended that a filter be fitted to prevent hydraulic
cylinder damage.
3
Water Blasting - Water blasting, steam cleaning or other
pressurised cleaning processes can force dirt etc. into
undesirable places that may cause damage or rapid part
wear to items such as bearings, seals, chains, bushes etc.
Caution must be exercised.
4
Box set lifting eye profile - these profiles are are provided
for easy removal of the dual boxes from the side frames.
Do not use when boxes are loaded nor to lift machine.
26
Maintenance & Care - Lubrication Instructions
Your new Duncan Renovator
Seed Drill will give long and
efficient service if given normal
care and maintained properly.
Lubrication Points on the Renovator
3
4
11
4, 5
13
12
1
Fig 22
10
6
8, 9
4
Precautions with Grease
7
2
Greases should not be mixed as the
structure may be weakened by the
mixes of different types of thickener,
which may cause softening and loss
of grease from the bearings by
running out.
Fig 23
1
Lubrication Chart
Item Components
1
2
3
4
5
6
7
8
9
10
11
12
13
*
Wheel Bearings
Wheel Leg Pivots
Gearbox
Drive Chains
Drive Shafts (Pedestal)
Agitator Shaft Supports
Seeder Shafts
Disc Opener Bearings
Disc Arm Castings
Disc Opener Fr. Pivots
Turnbuckles
Jockey Wheel Bearings
Coupling
Table 9
Lubricant
Frequency
Castrol LMX Grease
Castrol LMX Grease
Castrol Oil Agri Trans Plus
Suitable Roller Chain Lubricant
Pre-packed & Sealed (Refer Page 53-55)
Nylon Bushes (Refer Page 63)
Nylon Supports (Refer Page 64)
Pre-packed & Sealed
Castrol LMX Grease
Castrol LMX Grease
Castrol LMX Grease
Pre-packed & Sealed
Castrol LMX Grease
Annually
Weekly
Maintain Level
See Maintenance Schedule
Not Required
Not Required
Not Required
Not Required
Daily
Monthly
Monthly
Not Required
Weekly
The lubrication frequencies are only a guide. Actual frequency will be dependent on extent of use and ground conditions.
Pt. No. 67354
Issue 0207
27
Maintenance & Care
Maintenance Schedule
Components
Disc Openers
Depth Adjustment Collar
Seeders/Agitators/Bottom Flaps
Wheel Nuts
Pivot Pin Fasteners
Coupling & Safety Chains
Roller Chains
Gearbox
Hydraulics (Oil Leaks)
Tyre Pressures (25psi / 1.8bar)
Press Wheels
Bolted Connections
Table 10
Daily
Weekly
Pre Season
(or after 20Ha)
(or after 75Ha)
(or 500 Ha)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Maintenance Schedule
(Refer also to Summary Chart, above)
2
1
1 Bolted Connections
All bolted connections of the machine should be
checked after the first 30 hours of operation and
retightened if necessary and thereafter at regular
intervals. It is suggested that this is done every 500
hectares or annually, whichever occurs first.
2 Gearbox
The oil level in the gearbox can be seen in the oil gauge
window (1). Changing the gearbox oil is normally not
necessary. For refilling the oil remove the 1/2” BSP plug
on the top face of the gearbox (2), Castrol Oil Agri Trans
Plus should be used. The total filling capacity is 1.25
litres (refer Fig 24).
DO NOT OVERFILL.
28
Fig 24
3 Drive Chains
All drive chains (1) (Fig 25) should first be checked
after every 20 hours of operation and thereafter
weekly or after 75Ha of operation as follows:The metering wheels of the seed drill are driven via
roller chains from the drive wheel.
Cleaning of the roller chains is recommended after
long periods of operation. Remove the chain, wash in
kerosene and then dip them in heated grease or oil or
spray them with a suitable commercial roller chain
lubricant.
1
4 Wheel Rocker Pivots
Wheel rocker pivots (4 per machine) must be greased
regularly (weekly or after every 75Ha) to provide
lubrication and flush out any dirt. Refer Fig 26 (1).
1
5. Depth Adjustment Collar
Grease the depth adjustment collar (1) regularly to
ensure it does not seize up. Also check for dirt buildup
around the ram shaft seals to ensure seal damage
does not occur. Refer Fig 27
Fig 25
6. Tyre Pressure
The recommended tyre pressure is 2.4 bar (35 psi).
Check the tyre pressures regularly to ensure correct
pressure is maintained. Weekly checks are
recommended.
7. Disc Openers
Front coulter bearings are sealed and do not require
lubrication. Check discs for any lateral movement
(wobble) on a regular basis. Replace bearings if there
is any noticeable wobble.
There is one grease nipple on each disc opener frame
pivot and disc assembly casting. Frame pivots should
be greased monthly while disc castings should be
greased daily to provide lubrication and to flush out
any dirt.
1
Fig 26
8. Length of Seed/Fertiliser Tubes
These tubes can stretch over a period of time and
require checking at approximately six monthly
intervals. Shorten if necessary to avoid bends which
will restrict the flow of seed/fertiliser.
9 Framework
The framework structure should be inspected annually
for defects, i.e., cracks in members or welded
connections. The framework should be cleaned prior
to the inspection.
1
Fig 27
Pt. No. 67354
Issue 0207
29
Maintenance & Care (Continued)
10 Bottom Flaps (Fig 28)
Im
po
rta
nt
2
!
1
3
4
5
The required seed rate is controlled by both the metering
wheels and the bottom flaps. The seed flows from the seed
box into the metering wheel housings. Inside the metering
wheel housing (1) the seed is caught between the metering
wheel (2) and the bottom flap (3). The metered amount of
seed is transported by the metering wheel to the edge of
the bottom flap where it drops off into the seed guide tube
which leads to the coulter. Varying grain sizes require the
matching of the flap clearance to the different grain sizes.
This matching is done by raising or lowering the bottom
flaps by using the flap adjusting lever on the LH end of the
seed box. If larger foreign particles, e.g. stones get
between the metering wheel and the bottom flap, the
bottom flap can give way downwards. A strong return
spring (4) brings the bottom flap immediately back into the
working position.
The metering system should be checked every 1/2 year
or before any sowing period with an empty seed box
and empty metering housings.
Fig 28
Use the following procedure:
Put the bottom flap setting levers (1) (located on the LH
end of the seed boxes) in position “1” for the front box and
position “1” for the rear box. Refer Fig 29.
By turning the metering wheel shaft by hand check the
flaps are all set to a gap of 0.1 to 0.5mm (refer Fig 28).
To adjust individual flaps use the spring tensioning screw
(5) (Fig 28).
1
Fig 29
Note: Maintenance Schedule (page 28)
Where the frequency is given in terms of use (eg. weekly) or
area covered (eg. 75 Ha) perform the maintenance task based
on whichever occurs first.
Preparing the Machine for Storage.
Locate on a dry level surface. The machine should be stored
wherever possible so the rams are not supporting any weight.
The drive chains should be lubricated with suitable roller chain
lubricant before prolonged periods of storage.
For longer term storage remove seed/fertiliser tubes from the
boot assembly and allow to hang without deformation. Check
tube lengths when replacing.
It is recommended that maintenance be carried out at the end
of the season, giving sufficient time to obtain spare parts
and/or carry out repairs if required.
30
Renovator
Maintenance Notes
Pt. No. 67354
Issue 0207
31
Renovator
32
Maintenance Notes
Parts List
‘MkIII Renovator’ Seed Drill
From Serial Number 071731
Head Office:
P.O. Box 2018
Hilton Highway, Washdyke
Timaru, New Zealand
Telephone (03) 688 2029
Facsimile (03) 688 2821
Australian Branch:
4B Silverton Close
Laverton North 3026
Melbourne, Australia
Telephone (03) 9314-9666
Facsimile (03) 9314-6810
Pt. No. 67354
Issue 0207
33
‘Renovator’ Seed Drill
Dual Box Complete Assembly
17
30
13, 14
31
27
28
29
18, 19
1
8
20 to 24
2
26
12
17
11
15
16
7
25
27, 28
33
5
32
8
6
3
34
‘Renovator’ Seed Drill
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16
17
17
17
18
19
20
21
22
23
24
25
26
27
28
29
30
30
31
31
32
33
Part No.
Refer pages 38-41
Refer pages 42/43
Refer pages 44/45
Refer pages 70/71
Refer pages 66-69
Refer pages 46/47
Refer pages 48-52
Refer pages 54/55
Refer pages 65
Refer page 53
Refer page 56
Refer pages 58/59
Refer page 62
Refer page 63
Refer page 64
26623
26622
22562
26668
26669
25995
45341
25730
25723
45131
45159
45167
26575
22051
45459
45140
45160
22916
26664
26541
26540
26562
26599
Dual Box Complete Assembly
Description
Main Frame and Drawbar Assembly
Wheel System
Hydraulic System
Wiring and Lighting (Optional - not shown)
Disc Opener Assembly
Tine and Boot Assembly
Drive Chains
Jockey Wheel and Transfer Drive System
Hectaremeter Kit (Not shown)
Seed Box Drive Shafts
Gearbox Final Assembly
Seedbox Assembly
Agitator Drives
Agitator Shaft Assembly (Inside Seedbox)
Seeder Mechanism
19 Run Footboard Assembly
23 Run Footboard Assembly
19 Run Calibration Tray
23 Run Calibration Tray 1520mm (Not shown)
23 Run Calibration Tray 1390mm (Not shown)
Drive Guard
Nut, Wing, M10
Jockey Arm Tension Spring
Jockey Arm Tension Eyebolt
Hex, M12 Nut
M12 H/D Flat Washer
M12 Spring Washer
Footboard Step
Crank Arm and Handle Assy
M16 x 45 Bolt
M16 Nyloc Nut
M16 H/D Flat Washer
19R Weather Skirt
23R Weather Skirt
LH Pedestal W/Assy 19 Run
LH pedestal W/Assy 23 Run
Drive Pedestal W/Assy
Calibration Tray Bracket
Qty.
1
1
1
1
1
19 or 23
4
1
1
2
1
2
2
2
38 or 43
1
1
2
2
2
1
1
1
1
2
2
1
1
1
6
6
3
2
2
1
1
1
4 or 8
Note. Refer to page 11 for safety decal information
Pt. No. 67354
Issue 0207
35
‘Renovator’ Seed Drill
Single Box Complete Assembly
13, 14
26
31
27, 28, 29
25
2
1
5
33
32
10
12
30
11
17
7
15
18, 19
16
27, 28
8
6
3
36
20 to 24
‘Renovator’ Seed Drill
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16
17
17
17
18
19
20
21
22
23
24
25
26
27
28
29
30
30
31
31
32
33
Part No.
Refer pages 38-41
Refer pages 42/43
Refer pages 44/45
Refer pages 70/71
Refer pages 66-69
Refer pages 46/47
Refer pages 48-52
Refer pages 54/55
Refer page 65
Refer page 53
Refer page 57
Refer pages 60/61
Refer page 62
Refer page 63
Refer page 64
26821
26820
22562
26668
26669
25996
45341
25730
25723
45131
45159
45167
26575
22051
45460
45140
45160
22916
26664
26811
26810
26802
26599
Single Box Complete Assembly
Description
Main Frame and Drawbar Assembly
Wheel System
Hydraulic System
Wiring and Lighting (Optional - not shown)
Disc Opener Assembly
Tine and Boot Assembly
Drive Chains
Jockey Wheel and Transfer Drive System
Hectaremeter Kit (Not shown)
Seed Box Drive Shafts
Gearbox Final Assembly
Seedbox Assembly
Agitator Drive
Agitator Shaft Assembly (Inside Seedbox)
Seeder Mechanism
19R Footboard Assy (Single)
23R Footboard Assy (Single)
19 Run Calibration Tray
23R Calibration Tray 1520mm (Not shown)
23R Calibration Tray 1390mm (Not shown)
Drive Guard
M10 Wing Nut
Jockey Arm Tension Spring
Jockey Arm Tension Eyebolt
M12 Hex Nut
M12 H/D Flat Washer
M12 Spring Washer
Footboard Step
Crank Arm and Handle Assy
M16 x 45 Bolt
M16 Nyloc Nut
M16 H/D Washer
19R Weather Skirt
23R Weather Skirt
LH Pedestal W/Assy 19 Run (Single)
LH Pedestal W/Assy 23 Run (Single)
Drive Pedestal W/Assy (Single)
Calibration Tray Bracket
Qty.
1
1
1
1
1
19 or 23
3
1
1
1
1
1
1
1
19 or 23
1
1
1
1
1
1
1
1
1
2
2
1
1
1
6
6
3
1
1
1
1
1
2 or 4
Note: Refer to page 11 for safety decal information
Pt. No. 67354
Issue 0207
37
‘Renovator’ Seed Drill
Mainframe and Drawbar
14, 15
13, 18
7
9
10
4
5, 6
3
1
11
12, 13
19, 20
17
3
8
11
13, 16
38
‘Renovator’ Seed Drill
Item
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Part No.
26512
26510
Refer Pages 46/47
26550
4800315
26061
45292
26570
26580
26577
26578
43830
45065
45141
47548
45084
45181
45075
45042
45140
Mainframe and Drawbar
Description
19 Run Main Frame
23 Run Main Frame
Coil Tines & Boots
Drawbar Assembly
Hose Support
Drawbar Axle (Renovator)
Lynch Pin, 7/16” x 1 1/2”
Centre Hitch Welded Assembly
Towing Eye Assembly
LH Support Stay
RH Support Stay
Safety Chain Assembly
M20 x 65 Grade 8.8 Bolt
M20 Nyloc Bolt
7/8” x 7” UNF Bolt
7/8” Nyloc Nut
M20 x 240 Grade 8.8 Bolt
M8 x 12 S/H Grub Screw
M20 x 150 Grade 8.8 Bolt
M16 x 60 Grade 8.8 Bolts
M16 Nyloc Nuts
Qty.
1
1
19 or 23
1
1
1
2
1
1
1
1
2
4
6
1
1
1
1
1
4
4
Pt. No. 67354
Issue 0207
39
‘Renovator’ Seed Drill
Mainframe and Drawbar
41, 43
40
42, 43
54, 55
49
44
50
53
46
45
54, 56
51, 52
40
‘Renovator’ Seed Drill
19R Drawbar Turnbuckle Parts
40
43395
41
26557
42
26558
43
45272
23R Drawbar Hydraulic Parts
44
43852
45
26723
46
26724
47
48
49
43496
50
43393
51
43147
52
43617
53
43280
54
45272
55
26557
56
26558
Mainframe and Drawbar
H/D Ratchet Turnbuckle
Clevis Pin 135mm
Clevis Pin 90 mm
R Clip
1
1
1
4
Hydraulic Clyinder
Hydraulic Hose 2.80m
Hydraulic Hose 2.5m
1
1
1
3/4” UNO to 3/8”BSPT Elbow
3/8” BSP S/S Ball Valve
1/2” BSP Quick Release Coupling
Dust Cover
3/4” UNO to 3/8” BSPM Nipple
R Clip
Clevis Pin 135mm
Clevis Pin 90mm
1
1
2
2
1
4
1
1
Note: 23R Drawbar hydraulic parts (44-56) can be purchased as a kit for the 19R machine, part number 26720K.
Pt. No. 67354
Issue 0207
41
‘Renovator’ Seed Drill
Wheel Rocker System
1
3
2
15
16
19
23, 24
20, 21, 22
19
10
9
4
5
12
6
7
14
11
8
42
13
‘Renovator’ Seed Drill
Item
1
1
2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Part No.
26605
26607
26606
26608
26585
43596
43597
43598
43599
43600
26620
43976
43421
10282
45303
43836
43833
26592
26588
26598
45437
45139
45153
45042
45140
43120
Wheel Rocker System
Description
Qty.
LH Wheel Rocker W/Assy 23R
LH Wheel Rocker W/Assy 19R
RH Wheel Rocker W/Assy 23R
RH Wheel Rocker W/Assy 19R
Rocker Pivot Assy
ADR M16-1.5P x45 Hub Stud
ADR M16-1.5P Wheel Nut
ADR M27-1.5P Castle Nut
ADR 62mm Hub Cap
ADR Hub MkII
ADR MkII Stub Axle (Welded to Wheel Rockers)
Seal Kit
30209 J2 Inner Bearing
30206 J2 Outer Bearing
3.5 Diameter x 40 Long Cotter Pin
Trash Shield (part of item 10)
Mk 2 ADR Hub and Stub Assembly Complete (Items 4-14)
Wheel 10/80-12
Rocker Shaft Plug (Not Shown)
LH Wheel Scraper Assy
RH Wheel Scraper Assy
M12x 50 Bolt
M12 Nyloc Nut
M12 Light Flat Washer
M16 x 60Grade 8.8 Bolt
M16 Nyloc Nut
M8 x 1.25 Pitch Grease Nipple x 90 degree (Not Shown)
1
1
1
1
4
10
10
2
2
2
2
2
2
2
2
2
2
2
4
1
1
4
4
4
16
16
4
Pt. No. 67354
Issue 0207
43
‘Renovator’ Seed Drill
Wheel Rocker System
3
5
1
2
Slave
Cylinder
Master
Cylinder
14
14
4
6
7
12, 13
17
11
10
9
8
15,16
18
44
19, 20
‘Renovator’ Seed Drill
Item
1
1
2
2
3
4
4
5
5
6
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Part No.
26700
26702
26701
26703
43848
26710
26713
26711
26714
26712
26715
26716
22449
43445
43399
43393
43147
43617
43280
45453
45139
22270
22262
45418s
45166
Wheel Rocker System
Description
Qty.
4” x 6.5” Master Rephasing Cylinder (23R)
(Includes pin)
3.25” x 6.5” Master Rephasing Cylinder (19R) (Includes pin)
3.75” x 6.5” Slave Rephasing Cylinder (23R)
(Includes pin)
3” x 6.5” Slave Rephasing Cylinder (19R)
(Includes pin)
Stroke Limiting Collar 7/8”
Hydraulic Hose, 2.63m (23R)
Hydraulic Hose, 2.33m (19R)
Hydraulic Hose, 3.40m (23R)
Hydraulic Hose, 2.80m (19R)
Hydraulic Hose, 5.60m (23R)
Hydraulic Hose, 5.30m (19R)
Hydraulic Hose, 2.4m
Hydraulic Valve Support Assy
1/2” BSPT to 3/8” BSPP Nipple
3/8” BSPT Nipple Male/Female Swivel
3/8” BSP S/S Ball Valve
1/2” BSP Quick Release Coupling
Dust Cover
3/4” UNO to 3/8” BSP Nipple
M12 x 140 Bolt
M12 Nyloc Nut
Clevis Spacer
Clevis Pin Assembly
M10 x 25 Set Screw
M10 Spring Washer
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
4
1
1
2
2
2
2
Pt. No. 67354
Issue 0207
45
‘Renovator’ Seed Drill
Tine and Boot Assembly
13
16, 17, 18, 19
12
11
5, 6, 7
2
3
4
14, 15
8, 10
9, 10
46
1
Left Hand
Tine Shown
‘Renovator’ Seed Drill
Item
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Part No.
21413
21414
26848
25615
26849
25608
25609
25610
45009
45003
45138
21691
45466
21690
45413
45137
Tine and Boot Assembly
Description
Qty.
LH Coil Tine
RH Coil Tine
LH Inverted Tee Clamp
RH Inverted Tee Clamp
Cast Inverted Tee Point
Fertilizer Tube, Standard
Fertilizer Tube, Angle 90o Left
Fertilizer Tube, Angle 90o Right
M10 x 60 Bolt, Class 8.8
M10 x 30 Bolt, Class 8.8
M10 Nyloc Nut
Tine Clamp Casting
M16 x 80 (4.6) Zinc Plated Bolt
75 x 75 RHS Clamp Plate
M8 x 35 Bolt
M8 Nyloc Nut
(dual box machine only)
(dual box machine only)
(dual box machine only)
(dual box machine only)
(dual box machine only)
19R 23R
10 12
9
11
19 23
19 23
19 23
13 17
3
3
3
3
38 46
38 46
76 92
38 46
38 46
19 23
19 23
19 23
Feed Hose - Dual Box
16
25620
17
25622
18
25624
19
25626
Feed
Feed
Feed
Feed
850mm
950mm
1050mm
1180mm
15
10
13
19
12
6
9
Feed Hose - Single Box
16
25620
17
25622
19
25626
Feed Hose 38mm x 850mm
Feed Hose 38mm x 950mm
Feed Hose 38mm x 1180mm
6
5
8
8
6
9
Hose
Hose
Hose
Hose
38mm
38mm
38mm
38mm
x
x
x
x
Note: The following parts supersede items 2 and 4 respectively:
Alternative to 4- 26845 Tungsten Chip Inverted Tee Point
Pt. No. 67354
Issue 0207
47
‘Renovator’ Seed Drill
Item
Part No.
Drive Chains Dual Box
Description
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
25724
22466
22537
22044
26350
25780
25742
26352
24103
22294
45180
45181
43388
13 T Sprocket 1/2” P x 20mm Bore
1/2” BS Chain x 55 Links (Transfer Shaft to Gearbox input)
25 T Sprocket 1/2” P x 20mm Bore
15 T Sprocket 1/2” P x 20mm Bore
13T/21T Change Sprocket
1/2” BS Chain x 47 Links (Gearbox to Boxshaft)
38 T Sprocket 1/2” P x 25mm Bore
13T/21T Crank Sprocket
1/2” BS Chain x 61 Links (Jockey Wheel Drive)
Sprocket Key (6 x 6 x 25)
M8 x 10 Socket Head Grub Screw
M8 x 12 Socket Head Grub Screw
1/2” Pitch Joining Link
1
1
2
2
1
2
1
1
1
8
14
2
4
14
Refer page 50
Front Chain Tensioner Box Shaft
1
15
Refer page 51
Chain Tensioner Transfer Drive
1
16
Refer page 50
Rear Chain Tensioner Box Shaft
1
17
Refer page 52
Chain Tensioner Jockey Wheel Drive
1
5, 10, 11
4, 10, 11
4, 10, 11
6, 13
6, 13
3, 10, 11
3, 10, 11
16
14
1, 10, 11
15
2, 13
7, 10, 12
8, 10, 11
9, 13
17
48
‘Renovator’ Seed Drill
Item
Part No.
Drive Chains Single Box
Description
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
25724
25980
22537
22044
26350
25781
25742
26352
24103
22294
45180
45181
43388
13 T Sprocket 1/2” P x 20mm Bore
1/2” BS Chain x 67 Links (Transfer Shaft to Gearbox input)
25 T Sprocket 1/2” P x 20mm Bore
15 T Sprocket 1/2” P x 20mm Bore
13T/21T Change Sprocket
1/2” BS Chain x 37 Links (Gearbox to Boxshaft)
38 T Sprocket 1/2” P x 25mm Bore
13T/21T Crank Sprocket
1/2” BS Chain x 61 Links (Jockey Wheel Drive)
Sprocket Key (6 x 6 x 25)
M8 x 10 Socket Head Grub Screw
M8 x 12 Socket Head Grub Screw
1/2” Pitch Joining Link
1
1
2
2
1
2
1
1
1
6
8
2
3
14
Refer page 51
Chain Tensioner Transfer Drive
1
15
Refer page 52
Chain Tensioner Jockey Wheel Drive
1
5, 10, 11
4, 10, 11
6, 13
3, 10, 11
2, 13
14
7, 10, 12
1, 10, 11
15
8, 10, 11
9, 13
Pt. No. 67354
Issue 0207
49
‘Renovator’ Seed Drill
Item
Part No.
1
2
3
4
5
6
7
Description
22535
22480
22522
22523
23376
45132
45462
5
4
Chain Tensioners
Dual Box Shafts
Qty.
Nylon Roller
Arm Assembly, RH
Torsion Spring, LH
Torsion Spring, RH
Chain Tensioner Anchor
M16 Hex Nut
M16 x 60 Bolt
2
2
2
1
1
2
2
2
7
1
6
2
4
6
5
50
1
7
‘Renovator’ Seed Drill
Item
Part No.
1
2
3
4
5
5
22535
25984
22523
45132
45461
25987
2
1
Description
Chain Tensioner
Transfer Drives
Qty.
Nylon Roller
Arm Assembly, RH, 60 Extension
Torsion Spring, RH
M16 Hex Nut
M16 x 55 Bolt (Dual Box)
Chain Tensioner/ Guard Double Bolt (Single Box)
1
1
1
1
1
1
3
4
2
3
1
4
5
5
Pt. No. 67354
Issue 0207
51
‘Renovator’ Seed Drill
Chain Tensioner
Jockey Wheel Drive
Item
Part No.
1
2
3
4
5
6
22535
23373
22523
23376
45119
45462
Description
Nylon Roller
Short Arm Assembly, LH
Torsion Spring, RH
Chain Tensioner Anchor
M16 Half Nut
M16 x 60 Bolt
3
5
Qty.
1
1
1
1
1
1
6
2
4
1
52
‘Renovator’ Seed Drill
Item
1
2
3
4
5
6
7
8
9
Part No.
Seed Box Drive Shafts
Description
22537
22294
25758
43385
43387
45137
45181
45411S
Qty.
Sprocket, 25T x 1/2” Pitch, 20mm Bore
Key, Sprocket 6 x6 x 25
Shaft, Box Drive
“Y” Bearing, YET 204, 20mm
Housing, Bearing, Press Steel, PFT47 (2 Flanges = 1 Housing)
Nut, M8, Nylock
Grubscrew, M8 x 12, Socket Head
Set Screw, M8 x 20, Zinc Plate
Locking Collar (Part of item 4 and not supplied seperately)
6
7
4
1
1
1
2
2
4
2
4
2
8
8
6
2
5
5
5
3
5
9
4
9
1
Pt. No. 67354
Issue 0207
53
‘Renovator’ Seed Drill
Jockey Wheel and Transfer
Drive System
5
8
3
6
9
17
30
7
31
9
1, 2
5
18
1
3
8
15
30
32
15
3
12
4
14
11
10
33
13
19
18
7
26
5
34
29
28
21
22
27
25
22
24
54
23
20
16
‘Renovator’ Seed Drill
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Part No.
43386
30359
26569
45180
26352
25735
45411S
45137
45417S
45152
26567
Refer Page 65
Refer Page 65
25725
25742
45181
22294
25744
25724
25726
17127
25739
25727
45140
25745
45401S
45164
45156
43036
25729
26568
45138
45625
Jockey Wheel and Transfer
Drive System
Description
Qty.
“Y” Bearing, YET205 (25mm)
Locking Collar, (Part of Item 1, not supplied seperately)
3 Bolt Bearing Housing, PF52, (2 Flanges = 1 Housing)
Drive Pedestal Shaft, Transfer
M8 x 10 Socket Head Grubscrew
13T/21T 1/2”P Crank Sprocket
Jockey Wheel Arm Assembly
Set Screw, M8 x 20 Class 4.6, Zinc Plated
M8, Nyloc Nut
M10 x 20 Class 4.6, Z/P Set Screw
M10 Light Flat Washer
Sensor Mount Bracket
Sensor
Magnet and Clamp
Jockey Arm Pivot Spacer
38T 1/2” P (25mm Bore) Sprocket
M8 x 12 Socket Head Grubscrew
6 x 6 x 25 Sprocket Key
Jockey Wheel and Axle Assembly
13T 1/2” P (20mm Bore) Sprocket
Jockey Drive Axle Spacer
6204-2RS1 Bearing
Jockey Axle Inner Spacer
Jockey Axle Outer Spacer (Loctite in place when fitted)
M16 Nyloc Nut
Jockey Drive Swing Guard
M6 x 16, Z/P Set Screw
M6, Z/P Spring Washer
M6, H/D Z/P Flat Washer
6205-2RS1 Bearing
Jockey Arm Pivot Outer Spacer (Loctite in place when fitted)
Hexagonal Drive Shaft
M10 Nyloc Nut
M16 Bellevilles Disc Washer
2
2
2
1
4
1
1
6
6
1
1
1
1
1
2
1
2
3
1
1
1
2
1
1
1
1
2
2
2
2
1
1
1
1
Pt. No. 67354
Issue 0207
55
‘Renovator’ Seed Drill
Item
Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
25756
22036
25755
22042
43366
45157
47031
45137
45399
45411S
45151
25762
26359
22294
45180
Dual Gearbox Assembly
Description
Qty.
Gearbox Sub-Assembly
Quadrant, Speed Adjusting
Lever, Front, Speed Adjusting
Label, Speed Indicator
Tri-Knob, M8, Tapped Centre
Washer, Flat, M8, Heavy Duty, Zinc Plate
Bolt, Coach, M8 x 40 Cup Head, Class 4.6, Zinc Plated
Nut, M8 Nyloc
Bolt, M8 x 30 Class 4.6, Zinc Plated
Bolt, M8 x 20 Class 4.6, Zinc Plated
Washer, Flat, M8, Light
Gearbox Final Assembly (Includes items 1 to 13 and items 15, to 17)
13T/21T 1/2”P Change Sprocket
Sprocket Key (not illustrated)
Grub Screw, M8 x 10 Socket Head (not illustrated)
2
11
5
10
10
8
12
10
4
1
1
1
1
1
1
1
4
3
6
1
1
1
1
2
2
13
9
11
1
9
10
13
3
7
11
10
11
12
8
12
14, 15, 16, 17
56
11
10
10
6
‘Renovator’
Item
Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
25763
22036
25755
22042
43366
45157
47031
45137
45399
45411S
45151
25762
26359
22294
45180
Description
Qty.
Gearbox Sub-Assembly
Quadrant, Speed Adjusting
Lever, Front, Speed Adjusting
Label, Speed Indicator
Tri-Knob, M8, Tapped Centre
Washer, Flat, M8, Heavy Duty, Zinc Plate
Bolt, Coach, M8 x 40 Cup Head, Class 4.6, Zinc Plated
Nut, M8 Nyloc
Bolt, M8 x 30 Class 4.6, Zinc Plated
Bolt, M8 x 20 Class 4.6, Zinc Plated
Washer, Flat, M8, Light
Gearbox Final Assembly (Includes items 1 to 13 and items 15, to 17)
13T/21T 1/2”P Change Sprocket
Sprocket Key (not illustrated)
Grub Screw, M8 x 10 Socket Head (not illustrated)
9
3
10
1
Single Gearbox Assembly
1
1
1
1
1
1
1
4
3
6
1
1
1
1
2
2
6
8
11
8
7
12, 13, 14, 15
9
10
9
8
5
Pt. No. 67354
Issue 0207
57
‘Renovator’ Seed Drill
Dual Seedbox Assembly
3
41
15
1, 2
1, 2
15
5
25, 33, 35
26, 44
7, 27, 21
16
4
26, 44
30
8
21
27
9
31
33
25
36
36
33
25
14, 29
25, 43, 44
13, 29
26, 44
37, 40
38, 40
17, 21 ,28
25, 30, 33, 35
6
19
Lid Hinge Detail
12
24
Location Tab Detail
15
20
21
28
39
10
23
18
32
25, 36
Gearbox not illustrated
for clarity
58
21
22
28
11
23
25, 33, 36
5
Latch Rod Detail
‘Renovator’ Seed Drill
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
35
36
37
38
39
40
41
41
42
43
44
Part No.
Refer Table Below
Refer Table Below
Refer Table Below
Refer Page 64
Refer Table Below
Refer Table Below
10143
10158
14442
22487
22490
22491
25708
25709
22568
47615
22855
43373
22419
45122
45136
45150
45368
27599
45139
45702
45758
45908
45186
22485P
25759
25760
45153
45435S
45433S
22445
22446
45907
Refer Page 63
43734
43733
45434
45159
43430
Dual Seedbox Assembly
Description
Qty.
Combi Box Only (No Lid)
Combi Box with Lid
Box Lid Only
Seeder Assembly
Box Shaft (20mm)
Flap Shaft (18mm)
Front Box Quadrant Plate
Rear Box Reverse Quadrant Plate
Rubber Body Plug
Latch Rod Assembly
Hinge Assembly
Hinge Pin
Front Flap Handle Assembly
Rear Flap Handle Assembly
Location Tab (Calibration Tray)
6 x 40 Pipe Lynch Pin
Agitator Access Blanking Plate
Black Edge Trim (Refer Table Below for Length per Box)
Box Shaft Connecting Sleeve
M6 Class 8.8 Zinc Plated Hex Nut
M6 Nylock Nut
M6 Zinc Plated Light Flat Washer
M10 Starlock Fixing Washer
Hinge Pin Spring Clip
M12 Nylock Nut
4.8 x 9.5 Monel Pop Rivet
M6 x 16 Zinc Plated Countersunk Posidrive Screw
M6 x 16 Zinc Plated Pan Head Machine Screw
M10 x 12 Socket Head Grubscrew
Box Set Lifting Eye Profile
Box Set Mounting Bracket LH
Box Set Mounting Bracket RH
M12 Zinc Plated Light Flat Washer
M12 x 40 Set Screw
M12 x 30 Set Screw
Front Agitator Drive Assembly (Refer Page 62)
Rear Agitator Drive Assembly (Refer Page 62)
M6 x 12 Pan Head Pozi Drive Screw M/C
Agitator parts
19R Renovator Transfer
23R Renovator Transfer
M12 x 35 Bolt
M12 H/D Flat Washer
Lashing Hook
1
2
2
38 or 46
2
2
1
1
28
2
6
6
1
1
4 or 6
8
2
2
4
4 or 6
36
12
4
6
24
8
4
20
4
2
1
1
32
4
12
1
1
12
2
2
2
2
2
4
Part Number for Different Width Machines
Item
1
2
3
5
6
18
19 Run
26642
26646
25875
25812
22530
2.5 m
23 Run
26640
26645
26651
26655
26657
3m
Dual Box Cover 19R Renovator
Dual Box Cover 23R Renovator
26768
26769
Pt. No. 67354
Issue 0207
59
‘Renovator’ Seed Drill
Single Seedbox Assembly
35
1, 2
4
7, 19, 25
5
6
24, 36
5
23, 30, 31
14
8
17
40 23 29 30
Lid Hinge Detail
28
23
37
38
11
22
19
20
26
10
Location Tab Detail
32, 34
23, 30, 31
12, 27
15, 19, 26
3
13
18
19
26
33
21
9
21
24, 36
16
23, 30, 31
29
23, 30, 31
60
Latch Rod Detail
‘Renovator’ Seed Drill
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
35
36
37
38
39
40
Part No.
Refer Table Below
Refer Table Below
Refer Table Below
Refer Page 64
Refer Table Below
Refer Table Below
10158
14442
22487
22490
22491
25709
22568
47615
22855
43373
22419
45122
45136
45150
45368
27599
45139
45702
45758
45908
45186
25934
25935
45153
45433S
22446
45907
Refer Page 62
43734
43733
43430
45434
45159
45435
26595
Single Seedbox Assembly
Description
Qty.
Combi Box Only (No Lid)
Combi Box with Lid
Box Lid Only
Seeder Assembly
Box Shaft (20mm)
Flap Shaft (18mm)
Rear Box Reverse Quadrant Plate
Rubber Body Plug
Latch Rod Assembly
Hinge Assembly
Hinge Pin
Rear Flap Handle Assembly
Location Tab (Calibration Tray)
6 x 40 Pipe Lynch Pin
Agitator Access Blanking Plate
Black Edge Trim (Refer table below for length per box)
Box Shaft Connecting Sleeve
M6 Class 8.8 Zinc Plated Hex Nut
M6 Nyloc Nut
M6 Zinc Plated Light Flat Washer
M10 Starlock Fixing Washer
Hinge Pin Spring Clip
M12 Nylock Nut
Pop Rivet, Monel 4.8 x 9.5
M6 x 16 Zinc Plated Countersunk Posidrive Screw
M6 x 16 Zinc Plated Pan Head Machine Screw
M10 x 12 Socket Head Grubscrew
Single Box Mounting Bracket LH
Single Box Mounting Bracket RH
M12 Zinc Plated Light Flat Washer
M12 x 30 Set Screw
Rear Agitator Drive Assembly (Refer Page 62)
M6 x 12 Pan Head Pozi Drive Screw, M/C
Agitator parts
19R Renovator Transfer
23R Renovator Transfer
Lashing Hook
M12 x 35 Bolt
M12 H/D Flat Washer
M12 x 40 Bolt
Hand Hold
1
1
1
19 or 23
1
1
1
14
1
3
3
1
2 or 3
4
1
1
2
2 or 3
16
6
2
3
14
4
2
10
2
1
1
16
10
1
4
1
2
2
2
2
4
2
1
Part Number for Different Width Machines
Item
19 Run
23 Run
1
26642
26640
2
26646
26645
3
25875
26651
5
25812
26655
6
22530
26657
16
2.5m
3.0m
Pt. No. 67354
Issue 0207
61
‘Renovator’ Seed Drill
Item
Part No.
Agitator Drives
Description
Qty.
1
22414
Agitator Drive Rear Housing
1
2
22415
Agitator Drive Front Housing
1
3
22416
Agitator Drive Spacer
2
4
22418
3/8” Pitch x 20mm Bore 21T Sprocket
2
5
22422
3/8” Pitch x 20mm Bore 15T Sprocket
2
6
22417
3/8” Pitch x 33 Link BS Chain
2
7
43396
3/8” Pitch Joiner Link
2
8
22425
Agitator Shaft Extension
2
9
22426
Seed Shaft Extension
2
10
43428
Nylon Bush
6
11
22419
Box Shaft Connecting Sleeve, 19 Run
2
11
23633
Box Shaft Connecting Sleeve, 15 Run
2
12
22420
Agitator Shaft Joining Collar
2
13
45415
M8 x 45 Class 4.6 Zinc Plated Bolt
2
14
45416
M8 x 60 Class 4.6 Zinc Plated Bolt
2
15
45137
16
45180SS
17
47615
1
M8 Nylock Nut
4
M8 x 10 Stainless Steel Socket Head Grub Screw
4
6 x 40 Pipe Lynch Pin
4
Rear Agitator
Drive Complete
Assembly
Pt No 22446
15
4
5
14
13
11
3
10
2
Front Agitator
Drive Complete
Assembly
Pt No 22445
16
12
10
17
10
11
12
9
8
Front assembly only shown exploded
62
6
7
15
‘Renovator’ Seed Drill
Agitator Shaft Assembly
Item
Part No.
1
Refer Below
Agitator Shaft Assembly
1
2
22420
16mm Agitator Joining Collar
2
3
22423
Agitator Shaft Support RH (Short)
2
4
22424
Agitator Shaft Support LH (Long)
2
5
22428
Agitator Shaft Support Cap
2
6
43442
5/8” Lurethane Wiper Seal
4
M10 x 10 Stainless Steel Sockept Head Grubscrew
4
M8 x 16 Grade 316 Stainless Steel Set Screw
4
M8 Grade 316 Stainless Steel Nylock Nut
4
M30 ISO Fine Zinc Plated Hex Lock Nut
4
7
45185SS
8
45410SSS
9
45137SS
10
47600
Description
Qty.
Part numbers for different machines
Item
1
19 Run
23 Run
26660
26659
Plain (RH) End
6
Centre Bearing
8
5
10
1
3
Drive (LH) End
7
9
2
6
4
10
Pt. No. 67354
Issue 0207
63
‘Renovator’ Seed Drill
Item
Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
Description
43375
43376
43377
43374
43378
22550
22551
22548
43379
43380
43382
43383
43362
4
1
Seeder Mechanism
Qty.
19R
30
30
30
Metering Housing
Shutter Slide
Seed Metering Wheel Assembly (Includes item 4)
Fine Seed Wheel (For Spares Ordering Only)
Bottom Flap & Bolt Assembly
Seeder Extension Funnel
Seed Diverter
Spring Clip, S/S
Seed Shaft Guide Bearing
Guide Bearing Tension Spring
Metering Wheel Clutch Hook
Seed Rate Disc Calculator
Fine Seed Wheel Brush (Optional Extra)
30
30
30
30
6
6
1
1
23R
38
38
38
38
38
38
38
6
6
1
1
3
2
8
13
10
4
3
5
9
1
7
8
6
10
11
12
7
64
6
‘Renovator’ Seed Drill
Item
1
2
3
4
5
6
7
8
9
10
Part No.
43409
43400
43408
43404
43403
43453
43461
43455
43456
43457
Hectaremeter Kit
Description
Qty.
Hectaremeter Kit, (Includes items 2 to 6)
Hectaremeter
Manual, Hectaremeter
Magnet and Clamp
Sensor, with Locknuts
Hectaremeter Cable
Cable, Recharging
Electronic Scales (Not shown)
Calculator (Not shown)
Sealtop Plastic Container (Not shown)
1
1
1
1
1
1
1
1
1
1
1
7
6
2
3
4
5
Pt. No. 67354
Issue 0207
65
‘Renovator’ Seed Drill
Disc Opener Assembly
1
21
22
16, 17
23
14
15
28
13
27
20
26
19
25
12
24
18
10
11
7
3
5
4
2
10
5
6
66
9
8
‘Renovator’ Seed Drill
Item
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Part No.
26676
26674
17537
22080
43352
22078
22035
11361
45141
18364
11351
45417S
45138
21244
26315
26310
26686
26688
45141
45138
45420
45051
21690
25562
45140
21245
45417s
45166
43119
Disc Opener Assembly
Description
Qty.
19 Run Disc Openers Frame
23 Run Disc Openers Frame
Bearing Housing
Dust Cap
V Ring Seal V-40A
Seal Collar
Action 2000 (318 dia) Disc
Hub Cap
M20 Nyloc Nut
Bearing Housing
Bearing
M10 x 20 Set Screw
M10 Nyloc Nut
Double Pivot Pin Assembly
Disc Opener Spring
T Bolt Spring Rod
Double Axle Arm Assembly
Single Axle Arm Assembly
M20 Nyloc Nut
M10 Nyloc Nut
M10 x 35 Bolt
M16 x 130, Class 8.8 Bolt
Clamp Plate
Disc Opener Frame Support W/Assy
M16 Nyloc Nut
Pivot Pin Assy
M10 x 20 Bolt
M10 Spring Washer
M8 x 1.25 Pitch Grease Nipple x 45 degree
1
1
1
1
1
2
1
1
1
1
2
6
6
10
10
10
9
1
10
10
10
12
12
12
11
1
12
12
12
4
2
2
4
2
2
2
12 14
Note
Quantities shown for items 2-12 are per disc, not per machine.
The double numbers are for the 19 Run first followed by the 23 Run.
Pt. No. 67354
Issue 0207
67
‘Renovator’ Seed Drill
Disc Opener Assembly
Hydraulics
10
2, 3
4
1
7
10
6
5
1
12, 13
10
14, 15
11
9
8
16
68
‘Renovator’ Seed Drill
Disc Opener Assembly
19R Disc Opener Turnbuckle Parts
Item
1
2
3
Part No.
43395
26557
45272
Description
HD Turnbuckle
Clevis Pin 135mm
R Clip
Quantity
1
2
4
23R Disc Opener Hydraulic Parts
4
5
6
7
8
9
10
11
12
13
14
15
16
43853
26694
26695
26696
43445
43399
43280
43393
43147
43617
26557
45272
22449
Hydraulic Cylinder
Hydraulic Hose 2.40m
Hydraulic Hose 0.60m
Hydraulic Hose 3.2m
1/2” BSPT to 3/8” BSPP Nipple
3/8” BSPT Nipple Male/Female Swivel
3/4” UNO to 3/8” BPSM Nipple
3/8” BSP S/S Ball Valve
1/2” BSP Quick Release Coupling
Dust Cover
Clevis Pin 135mm
R Clip
Hydraulic Valve Support Assembly
1
1
1
1
1
1
2
1
2
2
2
4
1
Note: 23R Disc Opener hydraulic parts (4-16) can be purchased as a kit (Part number 26725K)
for the 19R machine.
Pt. No. 67354
Issue 0207
69
‘Renovator’ Seed Drill
Note both lights viewed from lens side
RH Light Fitting Outline, P/N 43435
Divider
Wiring & Lighting (Optional)
Marker Light Fitting
Outline, Viewed
from lens side
Solder
Passage of wires
through light fittings
back plates and
lamp mounting
bracket
Cable Colour Key
Yellow
White
Green
Red
Brown
Marker Light Fitting
Outline, Viewed from lens
side
Cable Entry from LH Light
Y
W
G
R
Br
Fixing holes for markerlight to RH
light fitting
Cable Entry from Connector
Plug, through 6A Grommet and
new hole
Passage of wires through light
fittings back plates and lamp
mounting bracket
Divider
LH Light Fitting Outline
Solder
Fixing holes for
markerlight to
LH light fitting
Divider
6
Lighting supply
cable (End Details)
P/N 22960
5
5 mm Ensure outer casing of
cable protrudes past cable
clampby at least 5 mm
Cable Entry From
RH Light
Terminals viewed from
direction of cable entry
Slide rubber sleeve
along cable before
starting to wire up
terminals
Seven Pole Plug
P/N 43437
70
Cable
Colour
Terminal
Number
Yellow
White
Green
Red
Brown
1
3
4
6
7
‘Renovator’ Seed Drill
Item
Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
25913K
25915K
24228
24227
43435
43436
43438
43443
43444
45136
45137
45399
45403S
45860
Wiring & Lighting (Optional)
Description
Qty.
Complete Lamp Kit, 15 Run
Complete Lamp Kit, 19 Run
Lamp Bracket Assembly L.H.
Lamp Bracket Assembly R.H.
Combination Rear Lamp
Marker Lamp
Flex, 5 Core Trailer (15 Run x 9.3m, 19 Run x 10.0m)
Wire, Appliance, White 1mm x 1m
Wire, Appliance, Brown 1mm x 1m
Nut, Nyloc, M6
Nut, M8 Nylock
Bolt, M8 x 30 Class 4.6 Zinc Plated
Set Screw, M6 x 25
Screw, No. 12 x 3/4” Pan PZ Zinc Plated Self Tapping
Bulb, 5W Festoon 15 x 44mm
Bulb, 21W Festoon 15 x 44mm
RH Side
LH Side
8
9
16
15
1
1
1
1
2
2
1
1
1
4
4
4
4
4
4
4
10
16
16
10
16
15
9
8
5
5
14
14
4
3
13
15
7
11, 12
13
15
7
6
11, 12
Pt. No. 67354
Issue 0207
71
‘Renovator’ Optional Extras
2
5
4
3
9 or 14
8 or 13
1
72
‘Renovator’ Optional Extras
Optional Extras
Item
Part No.
1
26795
2
3
Description
Quantity
Rear Tow Hitch Assembly
1
26852k
26003
19199
Harrow Transport Kit (Items 2 to 3)
Harrow Transport Support Assembly
Shaft Locking Pin
4
4
4
5
6
7
26850k
26809
31478
45034
45139
Jack Stand Kit (Items 4 to 7)
Jack Support Bracket
Jack
M12x130mm Grade 8.8 Bolt (Not shown)
M12 Nyloc Nut (Not shown)
1
1
2
2
8
9
10
11
12
26856k
26855
24250
45410S
45137
45151
Baffle Extension Kit (Items 8 to 12)
Box Baffle Extension (Seeder Centre)
Box Baffle Extension
M8x16 Bolt (Not shown)
M8 Nyloc (Not shown)
M8 Light Flat Washer (Not shown)
1 kit/box
1
2
9
9
12
13
14
15
16
17
26856SSk
26855SS
24250SS
45410SSS
45137SS
45151SS
Baffle Extension Kit Stainless (Items 13 to 17)
Box Baffle Extension SS (Seeder Centre)
Box Baffle Extension SS
M8x16 Stainless Steel Bolt (Not shown)
M8 Stainless Steel Nyloc (Not shown)
M8 SS Light Flat Washer (Not shown)
1 kit/box
1
2
9
9
12
18
23767k
Small Box Baffle Extension Kit (Not shown)
3 kits/box
19
26858k
Optical Seed Level Indicator
1
19
Pt. No. 67354
Issue 0207
73
‘Renovator’ Small Seeds Box (Optional)
2
1
55
28,29
22
40,42,43
41,42,43
25
24
55
27
41,42,43
30
43
38
38
39
39
32
31
36
74
34
33
35
‘Renovator’ Small Seeds Box (Optional)
Small Box Arrangement
Item
1
1
2
2
3
3
4
4
5
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Part No.
26734
26752
26738
26756
26745
26762
26746
26763
26748
26765
43373
43375
43376
43377
43378
43379
43380
14442
27599
22490
22491
45702
45136
45150
45908
23625
23632
10143
Refer Page 77
23633
23732
47615
23679
23678
26780
26781
26782
43855
43856
43857
43858
43430
45271
45155
45418s
45419s
45152
45138
45186
45760
Description
17/19R Small Box Assembly
21/23R Small Box Assembly
17/19R Small Box Lid Assembly
21/23R Small Box Lid Assembly
17/19R Small Box Box Shaft
21/23R Small Box Box Shaft
17/19R Small Box Flap Shaft
21/23R Small Box Flap Shaft
17/19R Small Box Weather Shirt Holder (Not shown)
21/23R Small Box Weather Shirt Holder (Not shown)
Edge Trim
Metering Housing D8
Shutter Slide D8
Elite Seed Metering Wheel
Bottom Flap & Bolt Assembly
Seed Shaft Guide Bearing
Tension Spring
Rubber Body Plug (Not shown)
Hinge Pin Spring Clip
Hinge Assembly
Hinge Pin
Pop Rivet 4.8x12 (To fit items 5 & 37)
M6 Nyloc Nut
M6 Light Flat Washer
M6 x 16 Pan Posi
Eclipse Mounting Plate
Eclipse Mounting Bracket
Fertilizer Quadrant Plate
Small Seeds Gearbox Final Assembly
Box Shaft Short Connecting Sleeve
Eclipse Flap Handle Assembly
6 x 40 Pipe Lynch Pin
Lid Stay
Lid Stay Pivot Assembly
Hexagonal Drive Shaft (Small Box)
Hexagonal Transfer Drive Shaft
Cassette Support Bracket W/Assembly
Drive Cassette Support Bearing
Drive Cassette Support Housing
Drive Cassette 42/15T
Drive Cassette 21/17T
Plastic Lashing Hook
R Clip
M20 Light Flat Washer
M10x25 Grade 4.6 Z/P Bolt
M10x30 Grade 4.6 Z/P Bolt
M10 Light Flat Washer
M10 Nyloc Nut
M10x12 Socket Head Grub Screw
M6x25C/Sunk Posi Z/P
Qty 19R
Qty 23R
1
1
1
1
1
2.4m
19
19
19
19
3
3
6
3
3
3
14
8
6
6
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
3
3
11
2
17
14
2
2
1
1
1
1
1
3m
23
23
23
23
3
3
6
3
3
3
14
8
6
6
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
3
3
11
2
17
14
2
2
Pt. No. 67354
Issue 0207
75
‘Renovator’ Small Seeds Box (Optional)
Small Box Arrangement
Item
Part No.
46
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
26749
26767
43500
22548
22550
22551
43333
25608
25609
25610
26599
25626
26788
26789
26785
26786
45137
Description
19R Small Box Ripstop Weather Skirt (Not shown)
23R Small Box Ripstop Weather Skirt (Not shown)
Cray Clip 47-49mm Dia.
Spring Clip SS
Seeder Extension Funnel
Seed Diverter
Cable Tie
Fertilizer Tube
Angled Fertilizer Tube 90R
Angled Fertilizer Tube 90L
Calibration Tray Bracket
Feed Hose x 1180 (Not shown)
Feed Hose x 1475 (Not shown)
Feed Hose x 1700 (Not shown)
Fertilizer Tube Clamp Plate W/Assy
Fertilizer Tube Clamp Plate
M8 Nyloc Nut
Qty 19R
Qty 23R
1
19
19
19
19
19
13
3
3
2
7
6
6
19
19
19
1
23
23
23
23
23
17
3
3
4
8
8
7
23
23
23
Note: For sowing rates refer to page 15
For detailed assembly of seeder assembly refer to page 64
6
18,23,45
21
17,38
40,42,43
4
55
3
52 or 53 or 54
26,44
7-12,47-50
60
14,16
61
62
15
76
18-20
‘Renovator’ Small Seeds Box (Optional)
Item
Part No.
Description
Qty.
1
26792
Small Seeds Gearbox Sub Assembly
1
2
23615
Gearbox Speed Adjustment Lever
1
3
23616
Gearbox Quadrant
1
4
23621
Gearbox Speed Scale
1
5
43366
Tri Knob
1
6
44963
M8x35 Grade 8.8 Bolt
3
7
45137
M8 Nyloc Nut
7
8
45151
M8 Light Flat Washer
1
9
45157
M8 H/D Flat Washer
1
10
45411s
M8x20 Grade 4.6 Z/P S/Screw
1
11
45412s
M8x25 Grade 4.6 Z/P S/Screw
3
12
47031
M8x40 Grade 4.6 Cup Head Bolt
1
7
3
1
11
4
7
12
9
10
11
2
8
11
5
Pt. No. 67354
Issue 0207
77
78
Pt. No. 67302
Issue 0207
79
‘Renovator’ Press Wheels (Optional)
18
18
3,4
10
1
16
23
11
12
17
9
19
8
2
20
24-27
13
12
4,7
21
15
5 or 6
22
14
80
‘Renovator’ Press Wheels (Optional)
Item
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Part No.
26864
26866
26877
26889
43872
26882
26904
26890
26898
45271
26892
26886
26887
26888
26893
26894
26897
45130
45033
45026
45139
45048
45140
26891
43874
43873
26885
26901
Description
Qty.
23R Press Wheel/Tow Hitch Mainframe
19R Press Wheel/Tow Hitch Mainframe
Press Wheel Pivot Welded Assembly
Bearing Spacer 66mm
Bearings 6001
Press Wheel Arm W/Assembly Long
Press Wheel Arm W/Assembly Short
Bearing Spacer 16.5mm
Transport Pin
R Clip
Eyebolt Retention Pin
Spring Cap
12mm Spacer
M12 Washer 12x19x1.6mm
Inner Spacer
Outer Spacer
Eye Bolt M10
M10 Plain Nut
M12x120 Bolt 8.8
M12x65 Bolt 8.8
M12 Nyloc Nut
M16x110 Bolt 8.8
M16 Nyloc Nut
Renovator Press Wheel Spring
Oil Seal TC25407
Bearing 6203
Bearing Spacer 24mm
15"x80mm Wedge Press Wheel Components
19R
1
17
17
68
8
9
17
17
17
17
17
34
34
17
17
17
34
17
17
34
17
17
17
34
34
17
17
23R
1
21
21
84
10
11
21
21
21
21
21
42
42
21
21
21
42
21
21
42
21
21
21
42
42
21
21
Note: Maximum spring pre-compression is 40mm.
All bearings are sealed. No lubrication required.
Pt. No. 67354
Issue 0207
81
82
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement