Headend Equipment
Headend Equipment
PRD-3100
Receiver Decoder
INTRODUCTION
The PRD-3100 is a cost effective professional integrated receiver decoder. It is widely used in the satellite, cable and terrestrial
TV network with different tuner frontend DVB-S2/S, DVB-C and DVB-T. It demodulates the RF signal to the transport stream
with optional ASI output or Analog output. With dual DVB common slots, PRD-3100 works with most of the well known CAS
in the market and decrypts multiple services in a transport stream. The on board decoder can process a variety of digital
video and audio formats in MPEG-4 AVC/H.264 and MPEG-2, in Standard Definition and in High Definition. The TV channel is
decoded to digital and analog outputs, HDMI, YPbPr, CVBS, balanced and un-balanced audio. The powerful demodulation,
decryption and decoding capabilities, combined with user friendly WEB GUI and SNMP based remote control makes this
equipment one of the most competitive professional IRD in the market.
MAIN FEATURES
• Multiple tuner inputs DVB-S2/S, DVB-C, and DVB-T
• 2x DVB-CI Slots, Multi Programs, BISS-1 and BISS-E decryption
• Transport stream output from ASI (optional)
• SD/HD MPEG-2 and MPEG-4/H.264 digital video decoding
• Two digital audio channel decoding
of MPEG1 Layer II and AAC
• Rich Analog and Digital Outputs
including, CVBS, YPbPr, HDMI, XLR
• Remote Control and Supervision by SNMP, HTTP WEB
and Proprietary HDMS software
• Dynamic PMT auto detection and updating
• Support VBI TELETEXT, EBU/ DVB Subtitle, Closed Caption
• Configuration save and load after power off
Headend Equipment
SPECIFICATIONS OVERVIEW
DVB-S/S2 Tuner Input
Analog Video Output
Connector Type
1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
Input Frequency Range 950~2150MHz
Input Level -25~-65dBm
Symbol Rate 5~45MBaud/s for QPSK
10~31MBaud/s for 8PSK
Roll Off Factor DVB-S QPSK: 0.35
DVB-S2 8PSK: 0.35, 0.25, 0.2
Punctured Rates DVB-S QPSK: 1/2, 3/5, 2/3, 3/4, 4/5,
5/6, 8/9, 8/10
DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9,9/10
LNB Polarity Selection vtg. 0, 13V, 18V selectable
LNB Band Selection Tone 0/22KHz selectable
Satellite Selection Command DiSEqC 1.0
YPbPr Connector 1 set of RCA, 75Ω
CVBS Connector 1×BNC 75Ω, 1×RCA 75Ω
Video Standard NTSC, PAL, and SECAM
YPbPr Resolution 1080i×30, 1080i×29.97, 1080i×25,
720p×60, 720p×59.94,
720p×50, 480p×60, 576p×50,
576i×25, 480i×29.97
Signal Level I.0 Vp-p±5%
Frequency Response <±I dB, at 5.5 MHz for PAL/SECAM,
4.2MHz for NTSC and 15MHz
for HD YPbPr
Chroma-Luma Delay <±30 ns
Field Time Distortion <2%
Line Time Distortion <1%
Short Time Distortion <2%
Differential Gain <3%
Differential Phase <2°
Signal to Noise Ratio >55 dB (luminance weighted)
DVB-C Tuner Input
Connector Type Input Frequency Input Level Symbol Rate Constellation Bandwidth Input Return Loss 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
48~860MHz
45~75dBμV
1~7MBaud (ITU J.83 Annex A)
16/32/64/128/256QAM
6MHz/7MHz/8MHz
7dB (typ.)
DVB-T Tuner Input
Connector Type Input Frequency Input Level Constellation Bandwidth FFT Mode Guard Interval FEC Code Rate Input Return Loss 1×F type female 75Ω for Input, 1×F type
female 75Ω for loop through output
104~862MHz (VHF/UHF)
-20~-70dBm (Quasi Error Free, QEF)
DVB-T: QPSK/16-QAM/64-QAM
6MHz/7MHz/8MHz
DVB-T: 2K/8K
DVB-T: 1/4, 1/8, 1/16, 1/32
DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8
7dB (typ.)
TS Processing
Descrambler BISS Mode Common Interface DVB Common Scrambling Algorithm(CSA)
BISS-1, BISS-E
Dual PCMCIA slots, compatible with major CA CAMs in the market
ASI Output
Connector type Standard 2×BNC Female, 75Ω
DVB-ASI, EN50083-9
HDMI Output
Standard HDMI 1×HDMI 1.3 interface (no 1080p)
Video Resolution 1080i×30, 1080i×29.97, 1080i×25,
720p×60, 720p×59.94,720p×50,
480p×60, 576p×50, 576i×25, 480i×29.97
Audio Embedded one digital audio pass through
Digital Video Processing
Video Standard Video PID Bit Rate MPEG-2(MP@ ML for SD,MP@HL for HD)
MPEG 4/H.264 AVC Part 10 (MP@L3 for
SD, HP@L4.1 for HD)
< 80Mb/s
Digital Audio Processing
Number of Outputs 2×digital audio PIDs are decoded
Sampling Rate 32, 44.1 and 48KHz
Audio Bit Rate 32, 64, 96, 128, 160, 192, 224,
256, 288, 320, 352, 384, 416
and 448 kb/s for MPEG-1 Layer I
32, 48, 56, 64, 80, 96, 112, 128, 160, 192,
224, 256, 320 and 384 kb/s for MPEG1Layer II
Analog Audio Output
Connector type Output Impedance Output mode Number of Outputs 1×XLR Male Socket,
2 pairs of RCA audio
600Ω (balanced)
Left, Right, Dual Mono, Stereo
2 pairs of stereo audio outputs
(2 Audio PIDs are decoded)
Baseband Data Output
Subtitle DVB/EBU
VBI Teletext, WSS, VFD, VPS
Closed Caption EIA 608, EIA 708, EIA 608-to-708
Control & Monitoring
Connector Type 1×RJ-45, 10/100 Base-T
for equipment IP Control
Remote Control SNMP, HTTP Web,
Proprietary HDMS
Network System Management
Software
Local Control LCD display and 6-key keypad
Serial Port 1×RS-232 9-pin D-sub,
for debug use only
Equipment Upgrade FTP loader or USB
Physical
Dimension 44mm×483mm×255mm
Weight 2.4Kg Net, 4.4Kg Gross
Power Supply AC 90V~250V, 50/60Hz
Power Consumption 24W
Operating temperature 0~45°C
Storage temperature -10~60°C
Operating Humidity 10~90%, non-condensed
Certification
EMC: EN 55024:1998+A1:2001+A2:2003, EN 55022:2006+A1:2007,
EN 61000-3-2:2006, EN 61000-3-3:2008
FCC: Part 15 Class B
LVD: EN 60950-1:2006 + A11:2009
Headend Equipment
BACK PANEL INTERFACE
ORDERING INFORMATION
Model
PRD-3100-10X
DVB-T
DVB-S2
PRD-3100-20X
Tuner
DVB-C
ASI IN
×1
A
Common Interface
×2
×2
×2
×2
HDMI
×1
×1
×1
×1
CVBS
×2
×2
×2
YPbPr
×1
×1
×1
Audio L/R
×2
×2
Balanced audio XLR
×1
×1
USB
×1
×1
DVB-T
DVB-S2
A
×2
×2
×2
×2
×2
×2
×2
×2
×1
×1
×1
×1
×2
×2
×2
×2
×2
×1
×1
×1
×1
×1
×2
×2
×2
×2
×2
×2
×1
×1
×1
×1
×1
×1
×1
×1
×1
×1
×1
×1
×1
ASI-Output
BLOCK DIAGRAM
DVB-C
Headend Equipment
APPLICATION
Headend Equipment
PRD-201
Receiver decoder with transport stream processor
INTRODUCTION
PRD-201 is a professional integrated receiver decoder together with a built-in transport stream processor. Equipped with a
wide range of inputs of DVB-T/T2,S/S2,C tuner, ASI and TS/IP, it can be used in the satellite, cable, terrestrial and IP networks.
It provides a powerful transport stream processing engine for re-multiple×ing, descrambling, TS over IP encapsulation. It has
2 DVB common interface slots capable of working with most of well known CAS in the market to de-crypt multiple pay TV
services. Its re-multiple×ing capability enables creation of customized SPTS and MPTS output to IP and ASI ports. The PRD-201
is also a professional a broadcast quality decoder for MPEG-2 Standard Definition format, and provides a wide range of
industry standard digital analog video and audio outputs, CVBS, Component, AES/EBU, and SDI. This unique multi function
architecture makes the PRD-201 an ideal product for digital TV broadcast network.
MAIN FEATURES
• Multiple inputs DVB-S2/S/C/T,TS/IP, ASI, DS3(optional)
• SD MPEG-2 (MP@ML) digital Video decoding
• Digital audio embedded in SDI output
• Multiple Analog and Digital Outputs, ASI, CVBS, YPbPr, SD-SDI,
AES/EBU , TS/IP
• Fle×ible re-multiple×ing between ASI, Tuner and TS/IP Inputs
• RSSI, received Eb/No & BER monitoring
• 2× DVB-CI Slots, multiple TV programs decryption
• Dynamic PMT detection and automatic updating
• Support VBI TELETE×T, EBU/ DVB Subtitle
• UDP/RTP & Unicast/Multicast SPTS and MPTS over IP I/O
• Remote Control and Supervision by SNMP, HTTP WEB and
Proprietary HDMS software
Headend Equipment
SPECIFICATION
DVB-S/S2 Tuner Input
Connector type
Input frequency range
Input level Symbol rate Roll off factor Punctured rates LNB Polarization voltage
LNB Band selection tone Satellite selection command ASI Output
1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
950~2150MHz
-25~-65dBm
5~45MBaud/s for QPSK
10~31MBaud/s for 8PSK
DVB-S QPSK: 0.35
DVB-S2 8PSK: 0.35, 0.25, 0.2
DVB-S QPSK: 1/2, 3/5, 2/3, 3/4, 4/5,
5/6, 8/9, 8/10
DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10
0, 13V, 18V selectable
0/22KHz selectable
DiSEqC 1.0
DVB-C Tuner Input
Connector type Input frequency range Input level Symbol rate Constellation Bandwidth Input return loss 1×F type female 75Ω for Input, 1×F
type female 75Ω for loop through output
104~862MHz (VHF/UHF)
-20~-70dBm (Quasi Error Free, QEF)
DVB-T: QPSK/16-QAM/64-QAM
DVB-T2: QPSK, 16QAM, 64QAM, 256QAM
6MHz/7MHz/8MHz
DVB-T: 2K/8K
DVB-T: 1/4, 1/8, 1/16, 1/32
DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8
7dB (typ.)
ASI Input
Connector type Standard Input bit rate 1×BNC, 75Ω
DVB-ASI, EN50083-9
≤ 100Mb/s
DS3 Input (Option)
Connector type Standard Frame structure Bit rate 2×BNC Female, 75Ω, including loop through
Compliant with ITU-T G.703
Compliant with ITU-T G.752 and ITU-T G.804
44.736Mb/s
TS over IP
Connector Type Useful bit rate Protocol 1×RJ-45, 10/100M for TS/IP
70Mb/s for 10/100M
UDP / RTP, Multicast / Unicast, IGMPv2, ARP
TS Processing
TS Input Management Service and PID mgmt. PSI/SI Descrambler BISS mode Common Interface 2×BNC Female, 75Ω
DVB-ASI, EN50083-9
2 TS Re-multiple×ing from tuner, TS/IP
and ASI input (1 for mirror)
Digital Video Processing
Video Standard SDI Video Resolution Video Bit Rate MPEG-2(MP@ ML )
PAL, NTSC. SECAM
< 80Mb/s
SD-SDI Output
Connector type Serial interface Single level 1×SDI output, BNC Female, 75Ω
SMPTE 259M, 270 Mb/s (10bit)
800mV p-p
Analog Video Output
1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
48~860MHz
45~ 75dBμV
1~7MBaud (ITU J.83 Annex A)
16/32/64/128/256QAM
6MHz/7MHz/8MHz
7dB (typ.)
DVB-T Tuner Input
Connector type Input frequency range Input level Constellation Bandwidth FFT mode Guard interval FEC code rate Input return loss Connector type Standard TS processing Remux&demux among Tuner / DS3 (optional), ASI and TS/IP Inputs
Remu×, filtering and remapping
PSI/SI table regeneration, NIT and
SDT edition, LCN Edition and Re-generation
DVB Common Scrambling Algorithm (CSA)
BISS-1, BISS-E
Dual PCMCIA slots, compatible with major CA CAMs in the market
YPbPr Connector CVBS Connector Video Standard Signal Level Frequency Response Chroma-Luma Delay Field Time Distortion Line Time Distortion Short Time distortion Differential Gain Differential Phase Signal to Noise Ratio 1 set of RCA, 75Ω
1×BNC 75Ω, 1×RCA 75Ω
NTSC, PAL, and SECAM
1.0 Vp-p±5%
<±1 dB at 5.5 MHz
<±30 ns
<2%
<1%
<2%
<4%
<2°
>55 dB (luminance weighted)
Analog Audio Output
Connector type Output Impedance Output mode Number of Outputs XLR Male Socket
600Ω (balanced)
Left, Right, Dual Mono, Stereo
1 pair of stereo audio output
Ancillary Data Processing
Subtitle DVB/EBU
VBI Teletext, WSS, VFD, VPS
Control & Monitoring
Connector type Remote control Local control Serial port Equipment upgrade 1×RJ-45, 10/100M, for equipment IP Control
SNMP, HTTP Web, Proprietary HDMS
Network System Management Software
LCD display and 6-key keypad
1×RS-232 9-pin D-sub, for debug use only
FTP loader
Physical
Dimension Weight Power Supply Power Consumption Operating temperature Storage temperature Operating Humidity 44mm × 483mm × 255mm
3.4Kg Net, 5.4Kg Gross
AC 90V~250V, 50/60Hz
24W
0~45°C
-10~50°C
10~90%, non-condensed
Certification
EMC: EN 55024:1998+A1:2001+A2:2003, EN 55022:2006+A1:2007,
EN 61000-3-2:2006, EN 61000-3-3:2008
FCC: Part 15 Class B
LVD: EN 60950-1:2006 + A11:2009
Headend Equipment
BACK PANEL INTERFACE
ORDERING INFORMATION
Model
Tuner Input
PRD-201-30X
X = Tuner option:
PRD-201-43X
.T: DVB-T
.C: DVB-C
.S: DVB-S
PRD-201-44X
.S2: DVB-S2
.D : DS3
ASI Input
×1
×1
×1
DVB Common Interface
×2
×2
×2
Built-in Remultiplexer
●
●
●
ASI Output (mirrored)
×2
×2
×2
SDI Output (mirrored)
×2
×2
×2
Audio L/R (RCA)
●
●
●
YUV/RGB (RCA)
●
●
●
CVBS (BNC)
×1
×1
×1
CVBS (RCA)
×1
×1
×1
×10/×100M TS/IP Extension board (Dual RJ-45,6 Channel)
×10/×100M TS/IP Extension board (Single RJ-45, 32 Channel)
● Standard
BLOCK DIAGRAM
●
●
Headend Equipment
APPLICATION
Headend Equipment
PRD-204
IRD and Processor
INTRODUCTION
The PRD-204 IRD and Processor provides operators an ideal solution for receiving, remultiplexing, descrambling and
decoding operations. Equipped with a variety of inputs that ensures compatibility with all transmission media. The PRD-204’s
remultiplexing capabilities enable creation of new transport streams that are subsets of the original stream. Customized
services may be output as multiple SPTS or MPTS over IP, as well as over ASI. By the dual DVB common interfaces, PRD-204
could decrypt multiple services in one transport stream or two. PRD-204 is also a professional IRD that features a broadcast
quality decoder for MPEG-2 and MPEG-4 AVC/H.264 in both Standard Definition and High Definition formats, and provides
a variety of industry standard digital and analog outputs, including CVBS video, AES/EBU Audio, analog Audio, SD-SDI and
HD-SDI. The unit also performs HD down-conversion and aspect ratio adaptation of HD programs to generate professional
quality baseband analog video and audio outputs for easy integration with existing cable network infrastructure. This all-inone architecture makes the PRD-204 an ideal product for distribution and contribution networks.
MAIN FEATURES
• Variety of input options DVB-T2/S2/S/C/T/DTMB/ATSC/ISDB-T, DS3/E3, TS/IP and ASI
• Supports DVB-S2 Input Stream Identifier (ISI, optional) and DVB-T SFN MIP pass through
• Redundant backup among Tuner, ASI and TS/IP with configurable priority
• SD/HD MPEG-2 and MPEG-4 AVC/H.264 digital video decoding
• Two Audio PIDs decode or pass through (compressed) in SDI output
• Multiple Analog and Digital Outputs, ASI, CVBS, YPbPr, HDMI, SD/HD-SDI, AES/EBU Audio, TS/IP
• Built-in TS re-multiplexer receives ASI, Tuner and TS/IP Inputs
• 2×DVB-CI Slots, multi-program decryption, BISS-1 and BISS-E decryption
• Dynamic PMT detection and automatic updating
• Supports VBI TELETEXT, EBU/DVB Subtitle, Closed Caption
• UDP/RTP, Unicast/Multicast, and SPTS/MPTS over IP (full duplex, optional)
• Remote Control and Supervision by SNMP, HTTP WEB and Proprietary HDMS software
• PCM audio embedded in SDI and HDMI outputs
• PCM audio output on two AES/EBU audio output ports
• On Site software update through IP
• RSSI, received Eb/No & BER monitoring
Headend Equipment
SPECIFICATION
DVB-S/S2 Tuner Input (ISI Factory Optional)
Connector Type 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
Input frequency range
950~2150MHz
Input Level -25~-65dBm
Symbol Rate 2~45MBaud
Roll-off Factor DVB-S QPSK: 0.35
DVB-S2 8PSK: 0.35, 0.25, 0.2
FEC Code Rate DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 QPSK: 1/2, 3/5, 2/3, 3/4, 4/5,
5/6, 8/9,9/10
DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10
LNB Polarity Selection Voltage 0, 13V, 18V selectable
LNB Band Selection Tone 0/22KHz selectable
Satellite Selection Command DiSEqC 1.0
ISI ID 1~255 user configurable
DVB-C Tuner Input
Connector Type Input Frequency Range Input Level Symbol Rate Constellation Bandwidth Input Return Loss 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
51~862MHz
51~75dBμV
1~7MBaud (ITU J.83 Annex A)
16QAM, 32QAM, 64QAM, 128QAM, 256QAM
6MHz, 7MHz, 8MHz
7dB (typ.)
DVB-T/T2 Tuner Input
Connector Type Input Frequency Input Level Constellation Bandwidth FFT Mode Guarding Interval FEC Code Rate Input Return Loss 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
104 ~ 862MHz (VHF/UHF)
-20 ~ -70dBm
DVB-T: QPSK, 16QAM, 64QAM
DVB-T2: QPSK, 16QAM, 64QAM, 256QAM
6MHz, 7MHz, 8MHz
DVB-T: 2K, 8K
DVB-T2: 1K, 2K, 4K, 8K, 16K, 32K
DVB-T: 1/4, 1/8, 1/16, 1/32
DVB-T2: 1/4, 5/32, 1/8, 5/64, 1/16,
1/32, 1/64, 1/128
DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-T2: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6
7dB (typ.)
DTMB Tuner Input
Connector Type Input Frequency Range Input Level Symbol Rate Bandwidth Constellation Guard Interval Roll-off Factor Interleaving Depth FEC Code Rate 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
46.5~866MHz
-87~-29dBm
7.56MBaud
6MHz/7MHz/8MHz
4QAM-NR,4QAM,16QAM,32QAM, 64QAM
PN420, PN595, PN945
0.05
240,720
0.4, 0.6, 0.8
ATSC Tuner Input
Connector Type Input Frequency Range Input Level Symbol Rate Constellation Roll-off Factor Bandwidth 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
54~864MHz
-75~-7dBm(ATSC 8VSB)
10.762MBaud
8VSB
0.115
6MHz
ASI Input
Connector Type Standard Input Bit Rate 1×BNC female, 75Ω
DVB-ASI, EN50083-9
≤ 100Mb/s
DS3 Input (Option)
Connector Type Standard Frame Structure Bit Rate 2×BNC female, 75Ω, including loop through
Compliant with ITU-T G.703
Compliant with ITU-T G.752 and ITU-T G.804
44.736Mb/s
TS over IP
Connector Type Effective Bit Rate Protocol 1×RJ-45, 10/100 Base-T or 100/1000
Base-T for TS/IP
70Mb/s for 10/100/1000 Base-T
UDP / RTP, Multicast / Unicast, IGMPv3, ARP
TS Processing
TS Input Management
Demux and Remux among Tuner /
DS3(optional) / E3 (optional), ASI and
TS/IP Inputs
TS Output Management Demux and Remux for 2 independent
ASI outputs
Service and PID Mgmt. Remux, filtering and remapping
PSI/SI PSI/SI table regeneration, NIT and SDT
edition, LCN Edition and Re-generation
Descrambler DVB Common Scrambling Algorithm (CSA)
BISS Mode BISS-1, BISS-E
Common Interface Double PCMCIA slots, compatible with
major CA CAMs in the market
ASI Output
Connector Type Standard Output Bit Rate TS Processing 2 pairs of BNC female, 75Ω
DVB-ASI, EN50083-9
≤ 99Mb/s
2 Independent TS Re-multiplexed from tuner, TS/IP and 2 ASI inputs
HDMI Output
Standard Video Resolution and
Frame Rate
Audio Embedded 1×HDMI 1.3 interface (up to 1080i)
1080i×30, 1080i×29.97,1080×25,720p×60,
720p×59.94, 720p×50, 480p×60,
576p×50, 576i×25, 480i×29.97
1×stereo
Digital Video Processing
Video Standard MPEG-2(MP@ ML for SD, MP@HL for HD)
MPEG 4/H.264 AVC Part 10
(MP@L3 for SD, HP@L4.1 for HD)
SDI Video Resolution
1080i×30, 1080i×29.97, 1080i×25,
720p×60, 720p×59.94, 720p×50,
576i×25, 480i×29.97
Video PID Bit Rate < 80Mb/s
HD/SD-SDI Output
Connector Type SD Standard HD Standard Level 1 pair of BNCs (mirrored), female, 75Ω
SMPTE 259M, 270 Mb/s (10bit)
SMPTE 292M, 1.485 Gbit/s (10bit)
800mV p-p
Digital Audio Processing
Connector Type Number of Output Audio Sampling Rate Audio Bit Rate
Nominal Output Level Output Format Load Impedance 2×D-sub 9 male with XLR adaptor cables
2×audios are decoded or passed through
32, 44.1 and 48 KHz
32, 64, 96, 128, 160, 192, 224, 256,
288, 320, 352, 384, 416 and 448 Kb/s
for MPEG-1 Layer I, 32, 48, 56, 64, 80,
96, 112, 128, 160, 192, 224,256, 320
and 384 Kb/s for MPEG-1 Layer II
1V p-p (with standard test stream)
AES/EBU
110Ω (with XLR adaptor cables)
Headend Equipment
Analog Video Output
CVBS Connector CVBS Standard CVBS Resolution Nominal Output Level Frequency Response Chroma-Luma Delay Field Time Distortion Line Time Distortion Short Time Distortion Differential Gain Differential Phase Signal to Noise Ratio Redundancy
2×BNC female 75Ω
NTSC, PAL, and SECAM
576i×25, 480i×29.97
1.0 Vp-p±5% (with standard test stream)
<±1 dB, at 5.5 MHz for PAL/SECAM,
4.2MHz for NTSC
<±30 ns
<2%
<1%
<2%
<3%
<2°
>55dB (luminance weighted)
Analog Audio Output
among Tuner, ASI input and TS/IP input
TS Sync Loss
Main, Spare
Control & Monitoring
Connector Type 1×RJ-45, 10/100 Base-T, for equipment
IP Control
Remote Control
SNMP, HTTP (Web Interface) ,
Proprietary HDMS (Headend Device
Management System)
Local Control LCD display and 6-key keypad
Serial Port 1×RS-232 D-sub female, for debug use only
Equipment Upgrade Embedded FTP loader and Telnet
Physical
Connector Type 2×D-sub 9 male, with XLR adaptor cable
Output Impedance 600Ω (balanced)
Output Mode Left, Right, Dual Mono, Stereo
Number of Output 2 pairs of stereo audio outputs (2 Audio
PIDs or 4 channels are decoded)
Cross Talk Among Channels >70dB
THD <0.3% @ 400Hz, 1KHz test tone
Frequency Response ±0.5dB over 20Hz ~ 18KHz
Output Level 0dBm in 600Ω (0dBu),
adjustable range ±I0dB
Ancillary Data Processing
Subtitle VBI Closed Caption Redundancy Port Switching Condition Switching Mode DVB, EBU
Teletext, WSS
EIA 608, EIA 708, EIA 608-to-708
BLOCK DIAGRAM
BACK PANEL INTERFACE
Dimension Weight Power Supply Power Consumption Operating temperature Storage temperature -
Operating Humidity 44mm × 483mm × 255mm
3.4Kg Net, 5.4Kg Gross
AC 90V~250V, 50/60Hz
24W (exclusive of LNB power)
0~45°C
10~60°C
10~90%, non-condensed
Certification
EMC: EN 55024:1998+A1:2001+A2:2003, EN 55022:2006+A1:2007, EN
61000-3-2:2006, EN 61000-3-3:2008
FCC: Part 15 Class B
LVD: EN 60950-1:2006 + A11:2009
Headend Equipment
ORDERING INFORMATION
Model
PRD-204-10 Series
Interface
PRD-204-20 Series
PRD-204-30 Series
10X
12X
14X
16X
20X
22X
24X
26X
30X
32X
34X
36X
CVBS
2×BNC, Mirrored
●
●
●
●
●
●
●
●
●
●
●
●
AUDIO
2×R/L
●
●
●
●
●
●
●
●
●
●
●
●
HD-VIDEO
1×HDMI
●
●
●
●
●
●
●
●
●
●
●
●
SDI
2×BNC
●
●
●
●
AES/Balanced
2×D9, with extended
cable adaptor
●
●
●
●
TS Input
ASI IN
1×BNC
●
●
●
●
TS Output
ASI OUT
4×BNC (2×2 redundant)
●
●
●
●
100M Base-T / 6×Multicast
2×RJ45, Mirrored
100M Base-T / 32×Multicast
1×RJ45
GbE
1×RJ45
Management
1×RJ45
●
●
●
●
●
●
●
●
●
●
●
●
Upgrade
2×USB
●
●
●
●
●
●
●
●
●
●
●
●
RS-232
1×D9
●
●
●
●
●
●
●
●
●
●
●
●
ALARM/RELAY
1×D9
●
●
●
●
●
●
●
●
●
●
●
●
C
DVB-C
T
DVB-T
S2
DVB-S2
T2
DVB-T2
D
DS3
M
STM-1
A
Extended ASI port
N
No tuner frontend
Standard Video/Audio
Option
Digital Video/Audio
IP
Control/Upgrade
X = Tuner
Frontend option
● Standard
APPLICATION
●
●
●
●
●
●
●
●
●
●
●
●
●
Factory default option: X=S2
Headend Equipment
PRD-3006AV
6-Channel Multi-format HD Digital TV Receiver
INTRODUCTION
PRD-3006AV is a highly integrated 6-Channel Multi-format HD Digital TV Receiver that provides various options for up to 6
DVB-S2/S and DVB-T signals reception. Each on board decoder can work independently and process a variety of digital
video and audio formats in MPEG-4 AVC/H.264 and MPEG-2, in Standard Definition or in High Definition. The TV channel is
decoded into both digital and analog, and output via HDMI and CVBS respectively. Stable easy-to-use user interface via
On Screen Display (OSD) and first-class picture quality make PRD-3006AV a very cost effective solution for digital TV signal
reception system.
MAIN FEATURES
• Factory options for DVB-S/S2 and DVB-T tuner frontend
• Fully comply with MPEG-4 AVC/H.264, MPEG2 standard
• VBI Teletext (DVB ETS 300 706) and EBU/DVB Subtitle supported
• Up to 6 common interface for descrambling
(available on PRD-3006AV-CI)
• CVBS and HDMI output
• BISS 1 and BISS E decryption supported
• NTSC/PAL/AUTO TV standard conversion
• Easy-to-use On Screen Display (OSD) menu
• Automatic parameters storage and recovery
• Software upgrade via USB
ORDERING INFORMATION
Interface
Tuner input
Loop thru
PRD-3006AV-S2
PRD-3006AV-T
PRD-3006AV-CIS2
PRD-3006AV-CIT
6×DVB-S2
6×DVB-T
6×DVB-S2
6×DVB-T
×6
×6
×6
×6
×6
×6
×6
×6
×6
×6
Common Interface
HDMI output
USB port for upgrade
×6
×6
×6
×6
A/V output
×6
×6
×6
×6
Headend Equipment
SPECIFICATION
DVB-S/S2 Tuner (PRD-3006AV-S2)
Connector Type 6 × F type female 75Ω for Input
6 × F type female 75Ω for loop through
Input Frequency Range 950~2150MHz
Input Level -65~-25dBm
Symbol Rate
DVB-S QPSK: 1~45MBauds/s
DVB-S2 QPSK: 1~45MBauds/s
DVB-S2 8PSK: 1~45MBauds/s
Roll-off Factor DVB-S: 0.35
DVB-S2: 0.35, 0.25, 0.2
FEC Code Rate
DVB-S QPSK: 1/2, 2/3, 3/4, 5/6,6/7,7/8
DVB-S2 QPSK: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6,
8/9, 9/10
DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10
LNB Polarity Selection Voltage 0, 13V, 18V selectable
Satellite Selection Command DiSEqC 1.0
DVB-T Tuner (PRD-3006AV-T)
Connector Type Input Frequency Range Input Level Bandwidth Symbol Rate FFT Mode Guard Interval FEC Code Rate 6×F type female 75Ω for Input
6×F type female 75Ω for loop through
174~230MHz, 470 ~ 860MHz
-65~-25dBm
6MHz/7MHz/8MHz
DVB-T: 3.6~6.952Mbaud
DVB-T: 2K/8K
DVB-T: 1/4, 1/8, 1/16, 1/32
DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8
Digital Video/Audio Decoding
Video Standard
MPEG-2 MP@HL
H.264/AVC MP@L4.1, HP@L4.1,
MP@HL, AP@L3
Video PID Bit Rate Max. 60Mbit/s
Aspect Ratio 4:3, 16:9, Automatic
Video Resolution 480i, 576i, 1080i, 480p, 720p, 1080p
Video Format NTSC/PAL/AUTO
Audio Standard MPEG-1 layer I/II, MP3, MPEG-2 layer II,
Dolby Digital, HE-AAC
Sampling Rate 32, 44.1, 48KHz
BACK PANEL INTERFACE
APPLICATION
Common Interface
Type 6x PCMCIA (available on PRD-3006AV-CI)
Composite Video Output
Connector Type Output Impedance Output Level Frequency Response Differential Gain Differential Phase Chroma-Luma Delay RCA x1
75Ω
1.0V±30mVp-p
±0.5dB (4.8MHz)
≤5%
≤5°
≤30ns
HDMI Output
Connector Type HDMI 1.1 x1
Audio Output
Output mode Audio Standard Output Impedance Output Level Frequency Response Signal to Noise Ratio (SNR) RCA x2
Mono, Stereo
100Ω
±6dB
±0.5dB (20Hz~18Hz)
≥70dB
USB Interface
Connector Type Usage USB Type A
Firmware upgrade
General
Dimensions 483mm × 237mm × 45mm
Net Weight 3.7Kg
Temperature Work Temperature: 0~40ºC
Storage Temperature: -25~55 ºC
Humidity 10%~90%
Power Supply AC 90~256V 50Hz/60Hz, 25W
Headend Equipment
PENC-3000EC
Real-time single program 4:2:0 MPEG-2 encoder
INTRODUCTION
PENC-3000EC is a real-time single program 4:2:0 MPEG-2 encoder. It provides both analog and digital audio/video inputs like
CVBS, S-Video and SDI. By making compression of the base band TV signal, the encoder outputs a single program transport
stream (SPTS) to the ASI output port. Furthermore, PENC-3000EC has an ASI input port which can re-multiplex the encoded
SPTS with an external MPTS and generate a new MPTS. As an option, the MPTS of the encoder can also be outputted through
RJ-45 port over IP. User can use SNMP for equipment remote control and supervision. The configuration of an encoder with
built-in re-multiplexer makes PENC-3000EC an ideal product for the digital TV Headend Equipment where the high quality
stable video/audio compression is needed.
MAIN FEATURES
• Compliant with 4:2:0 MPEG-2 MP@ML video compression standard
• Multiple video inputs S-Video, SDI, ASI and CVBS
• Multiple audio inputs Stereo, Balanced audio, and SDI embedded audio input
• Support PAL, NTSC, an d SECAM analog TV standards
• User-configurable 4:3/16:9 aspect ratio
• Video compression bit rate from 1.5Mbps to 20Mbps
• Configurable GOP
• Built-in two-way Re-multiplexer
• Support PAT, PMT and SDT generation and NIT insertion
• SNMP based remote control system
• LCD display and user friendly operation menu
• Up to 6 MPTS or SPTS over multicast or unicast IP streaming output
ORDERING INFORMATION
Model
PENC-3000EC-10
PENC-3000EC-30
PENC-3000EC-40
S-Video Input
●
●
●
CVBS Input (BNC)
●
●
●
●
●
●
●
●
●
●
Built-in Remuliplexer
●
●
●
ASI Output (mirrored)
●
●
●
SDI Input (BNC)
Balanced Audio XLR Input
ASI Input
10/100M TS/IP Extension Board (Single RJ-45, 6 Channel)
● Standard
●
Headend Equipment
SPECIFICATION
Video Compression
Analog Input Digital Input Compression Standard Video Resolution Aspect Ratio Video Compression bit rate TS over IP Output
Analog NTSC, PAL and SECAM
SD-SDI (SMPTE-259M)
MPEG-2 MP@ML
480i (720×480) @29.97Hz: SMPTE125M
576i (720×576) @25Hz: ITU-R BT.656-4
4:3/16:9 selectable
1.5~20Mb/s
Audio Compression
Audio Channels Compression Standard Audio Mode Audio Sampling Rate Audio Compression bit rate 1 pair of stereo
MPEG-1 Layer II
Stereo, Joint Stereo, Dual Mono, Mono
32, 44.1, 48 KHz
32, 64, 128, 192, 256, 384 Kb/s
Audio/Video Input Interface
Analog Audio Analog CVBS S-Video SD-SDI SDI embedded audio Balanced Audio XLR L / R
1×BNC female, 75Ω
1×S-Video female, 75Ω
1×BNC female, 75Ω
Group 1 to 4 selectable
ASI Input
Connector Type Input bit rate Packet Mode Packet Length ASI Output Interface
Connector Type Output bit rate Packet Length Signal Level Source 2×BNC Female, 75Ω
≤ 99Mb/s
188 / 204 Bytes
800mVpp±10%
Any one of Built-in Re-mux,
ASI input and Encoder
Control & Monitoring
Connector Type 1×RJ-45, 10/100 Base-T, for equipment
IP Control
Remote Control SNMP, HTTP Web, Proprietary HDMS
Software
Local Control Front Panel
Software Upgrade Built-in FTP server + Telnet
Physical
1×BNC Female, 75Ω
≤ 100Mb/s
Byte or Burst
188/204 Bytes
TS Processing
TS Input Management Service and PID mgmt. Connector Type 1×RJ-45, 10/100 Base-T for TS/IP
Useful bit rate 70Mb/s min
Protocol UDP / RTP, Multicast / Unicast, IGMPv2,
ARP
Source Built-in Re-mux, ASI input, Encoder
Remux and demux between ASI input
and the SPTS encoded
Remux, filtering and remapping
PSI/SI PSI/SI table generation,
NIT and SDT edition
BLOCK DIAGRAM
BACK PANEL INTERFACE
Dimension Net weight Power Supply Power Consumption Operating Temperature Storage Temperature Operating Humidity 44mm × 483mm × 240mm
2.8Kg
AC 90V~250V, 50/60Hz
Maximum 20W
0~45°C
-10~6°C
10~90%, non-condensed
Certification
EMC: EN 55024:1998+A1:2001+A2:2003, EN 55022:2006+A1:2007,
EN 61000-3-2:2006, EN 61000-3-3:2008
FCC: Part 15 Class B
LVD: EN 60950-1:2006 + A11:2009
Headend Equipment
PENC-5100EC
High definition MPEG4/H.264 encoder/transcoder
INTRODUCTION
The PENC-5100EC is a high quality single channel high definition MPEG4/H.264 encoder/transcoder. It has a wide range of
digital/ analog video and audio inputs: CVBS, HD-SDI, HDMI, YPbPr and stereo audio. The compressed MPEG4/H.264 signal is
output to the ASI and IP ports. It can also be used as MPEG-2 to H.264 transcoder from IP or ASI ports. The PENC-5100EC’s remultiplexing function enables creation of a new transport stream between the TS of encoder and the TS from ASI or IP port.
The encoder/transcoder output can be multiple SPTS or MPTS over IP, as well as over ASI. In trans-coding mode, the digital
audios are looped through and time stamping is automatically implemented to ensure the synchronization between video
and audio. This unique encoder/transcoder with built-in re-multiplexer architecture makes the PENC-5100EC one of the best
solutions to meet the MPEG2 to MPEG4/H.264 migration requirement in today’s digital TV broadcast market.
MAIN FEATURES
• Video encoding bit rate from 2Mb/s to 20Mb/s
• Built-in Time Base Correction
• Multiple inputs HDMI, HD-SDI, YPbPr, and CVBS for
encoding
• Support VBR and CBR encoding mode
• ASI and TS/IP Input for Trans-coding
• Built-in re-multiplexer for TS from encoder and TS from
ASI and IP
• Support 10/100M TS/IP SPTS and MPTS
BLOCK DIAGRAM
• Digital audio pass through for trans-coding
• Support 2 pairs of analog stereo audio encoding with
optional extension board
• Remote Control and Supervision by SNMP, HTTP WEB
and Proprietary HDMS software
Headend Equipment
SPECIFICATION
Video Compression
Video Resolution Compression Standard Aspect Ratio Video Encoding Bit Rate TS Processing
1080i (1920/1440×1080) @25Hz,
29.97Hz, 30Hz: SMPTE 292M
720p (1280×720) @50Hz, 59.94Hz,
60Hz: SMPTE 292M
480i (720×480) @29.97Hz: SMPTE 259M
576i (720×576) @25Hz: SMPTE 259M
H.264, High Profile Level 4.0
4:3/16:9 selectable
2Mb/s-20Mb/s
TS Input Management TS Output Management Service and PID mgmt. TS over IP
Connector Type Useful Bit Rate Protocol Source Audio Compression
Audio Input Compression Standard Audio Mode Audio Sampling Rate Audio Compression Bit Rate Embedded Audio, Analog audio
MPEG-1 Layer II
Stereo, Joint Stereo, Dual Mono, Mono
48KHz
32~384Kb/s
Connector Type Output Bit Rate Packet Length Signal Level Source 1×D-sub 9 Female male
with XLR adaptor cables
1×BNC Female, 75Ω
1×BNC Female, 75Ω
3×BNC Female, 75Ω
1×HDMI 1.3
2×BNC Female, 75Ω
≤ 99Mb/s
188 / 204 Bytes
800mVpp±10%
Built-in Re-mux, ASI input, Encoder
Control & Monitoring
Connector Type Remote Control Local Control Software Upgrade ASI Input
Connector Type Input Bit Rate Packet Mode Packet Length 1×RJ45, 10/100M for TS/IP
70Mb/s for 10/100M
UDP / RTP, Multicast / Unicast, IGMPv2, ARP
Built-in Re-mux, ASI input, Encoder
ASI Output
Audio/Video Input
Analog Audio Analog CVBS SD-SDI YPbPr HDMI Remux and demux between ASI input
and the SPTS encoded
Remux and demux for mirrored ASI outputs
Remux, filtering and remapping
PSI/SI PSI/SI table regeneration,
NIT and SDT edition
1×BNC Female, 75Ω
≤ 100Mb/s
Byte
188/204 Bytes
1×RJ45, 10/100M, for equipment IP Control
SNMP, HTTP Web, Proprietary HDMS
(Network Management Software)
LCD display and 6-key keypad
Built-in FTP loader and Telnet
Physical
Dimension Net weight Power supply Power Consumption Operating Temperature Storage Temperature Humidity 44mm × 483mm × 340mm
3.2Kg
AC90 ~ 250V, 50Hz/60Hz
Maximum 20W
0~45°C
-10~60°C
10~90%, non-condensed
BACK PANEL INTERFACE
ORDERING INFORMATION
Functionality
Input
PENC-5100EC-30
PENC-5100EC-32
PENC-5100EC-40
PENC-5100EC-42
ASI
●
●
●
●
CVBS
●
●
●
●
SDI
●
●
●
●
YPbPr
●
●
●
●
HDMI
●
●
●
●
Audio 1
●
●
●
●
Audio 2
ASI x2
Output
● Standard
●
●
●
10/100M TS Over IP (6 Multicasts)
●
●
●
●
●
Management
●
●
●
●
RS-232
●
●
●
●
Headend Equipment
PENC-5800/5801EC
8-Way H.264 HD/SD Encoder
INTRODUCTION
PENC-5800/5801EC is a series of high density real-time H.264 HD/SD Encoders that can support up to eight High Definition
(HD) A/V signals compressing and encoding simultaneously. These A/V signals can be fed into the unit via 8x HDMI or 8x SDI
input ports as different factory options. The encoded streams can be then remultiplexed and output over its GbE IP and ASI
ports. All models support Time Base Correction (TBC) to ensure the audio and video synchronization, the features necessary
for the professional TV signal flow. The series provide two TS/IP operation modes. The first is “Full Duplex”, which allows one
MPTS or SPTS inputted over 1 multicast/unicast to make up a new MPTS with local encoders, then sends out the new one
over 1 multicast/unicast. In the second mode “Multiple output” which delivers up to 9 streams over IP. There are 8 un-stuffed
SPTS (lower bit rate but less PCR accurate than normal SPTS, from local encoders) and 1 MPTS (from internal reMultiplexer)
over the IP with different Unicast or Multicast IP addresses. PENC-5800/5801EC allows user to configure, monitoring and
manage over the informative front panel and keypad, or Web interface, or SNMP based management software from 3rd
party. This Encoder family presents brilliant picture quality, high density design, high stability system architecture, and the
hot-swappable power supply.
MAIN FEATURES
• Compile with H.264/AVC HP@L4.0
• MPEG1 Layer II, MPEG2 AAC-LC, MPEG4 AAC-LC audio compression
• 8-way real time encoder with re-multiplexed integrated
• Built-in re-Mux accepts up to 10 SPTS/MPTS (8 from local encoders,
2 from external input over IP and ASI) 1 ASI input (for daisy chain) & Redundant
• ASI output
• Full duplex Gigabit TS over IP I/O (under Full duplex operation mode)
• Up to 9 multicast/unicast output (under Multiple output operation mode)
• VBR and CBR encoding mode
• Free resolution downscale at same frame rate
• SNMP & HTTP WEB
• Redundant Power Supplies
• 19” x 1 U EIA standard chassis
Headend Equipment
SPECIFICATION
Video input & compression
DVB-ASI Output
Number of input ports HDMI x 8 or HD-SDI x 8
Compression Standard H.264/AVC HP@L4.0
Video Sampling Format 4:2:0, 8-bit, YCbCr
Video Encoding Bit Rate 2~30Mbps for each channel
Video Resolution &
Recommended Bit Rate
1080p (1920×1080) @ 59.94 Hz,50Hz:
SMPTE296M: 6~30Mb/s
1080 (1920×1080) @25Hz,29.97Hz,
30Hz:SMPTE274M: 6~24Mb/s
1080i (1440×1080) @25Hz,29.97Hz,
30Hz:SMPTE274M: 5~24Mb/s
720p (1280×720) @50Hz,59.94Hz,
60Hz:SMPTE296M: 4~24Mb/s
480i (720×480) @29.97Hz:SMPTE656M:
2~10Mb/s
576i (720×576) @25Hz: SMPTE656M:
2~10Mb/s
Other Video Resolution Free resolution downscale at same
frame rate
Aspect Ratio 4:3/16:9 Selectable
Audio Input & compression
Input HDMI or SDI Embedded audio
Audio Compression MPEG1 Layer II, MPEG2 AAC-LC,
MPEG4 AAC-LC (option)
Sampling Rate 48KHz
Compression Bit Rate 32~192Kbps(Mono), 64~384Kbps (Stereo),
128~512Kbps(AAC LC)
DVB-ASI Input
Interface Maximum Input Bit rate Data Transfer type Packet Length Signal Level Interface Max. Effective Data Rate Data Transfer type Packet Length Signal Level BNC Female, 75Ω
120 Mb/s
Byte
188 or 204 Bytes
800±80mV
Gigabit TS over P (Full Duplex Mode)
Standard Max. Effective Bit Rate Data Protocol Control Protocol IEEE 802.3, 10/100/1000 Base-T, Full Duplex
80Mb/s
UDP or RTP, SPTS or MPTS
ICMP, ARP, IGMPv2
Gigabit TS over IP Output (Multi-Channel IPTV Mode)
Standard Max. Effective Bit Rate Data Protocol Control Protocol IEEE 802.3, 10/100/1000 Base-T,
200Mb/s
UDP or RTP, SPTS or MPTS
ICMP, ARP, IGMPv2
Rear Panel
ASI In HD-SDI In 5800/5801EC-S)
HDMI In ASI Out 1 x BNC Female, 75Ω
8 x BNC Female, 75Ω (PENC8 x HDMI Male, 75Ω (PENC-5800/5801EC-H)
2 × BNC Female, 75Ω (1 Backup)
Front Panel
Control TS/IP Display 1×RJ-45, 10/100 Base-T
1× IP (GbE), RJ-45, 10/100/1000 Base-T
2 x 20 LCD Display
Others
BNC Female, 75Ω
100 Mb/s
Byte
188 or 204 Bytes
200 ~ 880mVp-p
Power Supply Operating Temperature Storage Temperature Operation Humidity AC90~260V 50/60Hz
0 ~ 45°C
-10 ~ 60°C
10 ~ 90%, (Non-condensed)
APPLICATION
DVB-C
DVB-S / S2
DVB-T / T2
IRD and Processor
HDMI / SDI
IRD and Processor
HDMI / SDI
IRD and Processor
HDMI / SDI
H.264 TS
PENC-5800/5801EC
8-Way H.264 HD/SD Encoder
DVB QAM Modulator
HFC
IP
HDMI
STB
IP Network
HDMI
STB
HDMI
DVD
HDMI
DVD
HDMI
Media Server
Headend Equipment
BLOCK DIAGRAM - FULL DUPLEX
BLOCK DIAGRAM - MULTI CHANNEL
Headend Equipment
BACK PANEL INTERFACE / PENC-5800EC-S
BACK PANEL INTERFACE / PENC-5800EC-H
ORDERING INFORMATION
Functionality
HDMI
Input
Output
PENC-5800EC-H
PENC-5801EC-H
x8
x8
HD-SDI (BNC)
PENC-5800EC-S
PENC-5801EC-S
x8
x8
ASI (BNC)
●
●
●
●
TS/IP (under full duplex mode)
●
●
●
●
ASI x2 (1x backup)
●
●
●
●
TS/IP (GbE)
●
●
●
●
AAC-LC Audio
●
Alarm
●
●
●
●
Control
●
●
●
●
RS-232
●
●
●
●
● Standard
●
Headend Equipment
PTM-4100PM
Integrated professional IRD and digital TV modulator
INTRODUCTION
The PTM-4100PM is built with an integrated professional IRD and digital TV modulator. It can provide to broadcaster and
operator with multiple functions of digital TV signal reception, re-multiplexing, descrambling, decoding and re-modulation.
It supports a wide range of tuner input DVB-S/S2, DVB-T/T2, DVB-C and is used in digital satellite, cable and terrestrial TV
networks. The re-multiplexing function enables creation of new SPTS or MPTS from tuner and ASI inputs. This new transport
stream may be output to QAM or COFDM modulator, IP and ASI ports. By using the dual DVB common interfaces,
PTM-4100PM can decrypt multiple pay TV services in each of the 2 slots. For security application, this equipment can
configured as a TS switch among tuner, ASI and TS/IP. The equipment can be controlled and supervised by SNMP, HTTP WEB
and proprietary HDMS software.
MAIN FEATURES
• Multiple inputs DVB-S2/S/C/T, TS/IP, ASI and DS3/E3 (optional)
• DVB-C QAM or DVB-T COFDM RF modulation output
• Redundant TS inputs among Tuner, ASI and TS/IP
• 100M UDP/RTP, Unicast/Multicast, and SPTS/MPTS over IP (half duplex)
• ASI input and output
• Service Drop or PID filtering and Remapping
• Flexible re-multiplexing among ASI, Tuner and TS/IP inputs
• PSI/SI adapting and re-generation, including NIT, LCN insertion etc.
• 2×DVB-CI Slots, Multiple TV program decryption
• Remote Control and Supervision by SNMP,
• HTTP WEB and Proprietary HDMS software
• On Site software update through IP
• RSSI, received Eb/No & BER monitoring
Headend Equipment
SPECIFICATION
DVB-S/S2 Tuner Input
ASI Output
Connector Type 1×F type female 75Ω for Input,
1×Ftype female 75Ω for loop through outp.
Input Frequency Range 950~2150MHz
Input Level -25~-65dBm
Symbol Rate 2~45MBaud
Roll-off Factor DVB-S QPSK: 0.35
DVB-S2 8PSK: 0.35,0.25, 0.2
FEC Code Rate DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 QPSK: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6,
8/9, 9/10
DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10
LNB Polarity Selection Voltage 0, 13V, 18V selectable
LNB Band Switching Tone 0/22KHz selectable
Satellite Selection Command DiSEqC 1.0
DVB-C Tuner Input
Connector Type Input Frequency Range Input Level Symbol Rate Constellation Bandwidth Input Return Loss 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
48~862MHz
45~75dBμV
1~7MBaud (ITU J.83 Annex A)
16/32/64/128/256QAM
6MHz/7MHz/8MHz
7dB (typ.)
DVB-T Tuner Input (DVB-T2 in option)
Connector Type Input Frequency Range Input Level Constellation Carrier Bandwidth FTT Mode Guard Interval FEC Code Rate Connector Type Standard Frame Structure Bit Rate RF Output
Connector Type Output Frequency Range Output Level Spurious Rejection Output Return Loss 1×F type female, 75Ω (primary output)
1×F type female 75Ω (-20dB for monitoring)
48~860MHz agile, step by 10 KHz
95~120dBμV, step by 1dBμV
55dB (typ.)
12dB (typ.)
Connector Type 1×RJ-45, 10/100M, for equipment IP Control
Remote Control SNMP, HTTP (Web Interface),
Proprietary HDMS
(Headend Device Management System)
Local Control LCD display and 6-key keypad
Serial Port 1×RS-232 D-sub female, for debug use
Software Upgrade FTP loader and Telnet
Dimension 483 × 399.7 × 44mm
Weight 6Kg
Power Supply AC 90V ~ 250V 50Hz/60Hz
Power Consumption 30W
Operating Temperature 0~45°C
Storage Temperature -10~60°C
Operating Humidity 10~90%, non-condensed
Certification
1×RJ-45, 10/100M or 100/1000M for TS/IP
70Mb/s for 10/100M/1000M
UDP / RTP, Multicast / Unicast, IGMPv2, ARP
TS Processing
TS Input Management TS Output Management Service and PID mgmt. PSI/SI Descrambler BISS Mode Common Interface Constellation QPSK/16QAM/64QAM
Bandwidth 5/6/7/8MHz
FFT Mode 2K
Guard Interval 1/4, 1/8, 1/16, 1/32
Code Rate 1/2, 2/3, 3/4, 5/6, 7/8
MER >36dB
Physical
2×BNC female, 75Ω, including loop through
Compliant with ITU-T G.703
Compliant with ITU-T G.752 and ITU-T G.804
44.736Mb/s
J.83 Annex A: 16/32/64/128/256QAM;
J.83 Annex B: 64/256QAM
3~7.2MS/s
< 0.3%
< 0.3°
< 0.5°RMS
> 35dB
DVB-T Re-Modulation
1 x BNC Female, 75Ω
DVB-ASI, EN50083-9
≤ 100Mb/s
188 or 204 Bytes
TS over IP
Connector Type Effective Bit Rate Protocol Constellation Symbol Rate I/Q Amplitude Error I/Q Phase Error Phase jitter MER Control & Monitoring
DS3 Input (Option)
2×BNC Female, 75Ω
DVB-ASI, EN50083-9
mirrored TS Re-multiplexing from Tuner,
ASI and TS/IP inputs
DVB-C Re-Modulation
1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
174~230MHz (VHF); 470 ~ 860MHz (UHF)
-20~-70dBm
QPSK, 16-QAM, 64-QAM
6/7/8 MHz
2K/8K
1/4, 1/8, 1/16, 1/32
1/2, 2/3, 3/4, 5/6, 7/8
ASI Input
Connector Type Standard Input Bit Rate Package Length Connector Type Standard TS Processing Remux and demux among Tuner / DS3
(optional) / E3 (optional),
ASI and TS/IP Inputs
Remux and demux for mirrored ASI outputs
Remux, filtering and remapping
PSI/SI table regeneration, NIT and SDT
edition, LCN Edition and Re-generation
DVB Common Scrambling Algorithm (CSA)
BISS-1, BISS-E
Double PCMCIA slots, compatible with
major CA CAMs in the market
EMC: EN 55024:1998+A1:2001+A2:2003, EN 55022:2006+A1:2007,
EN 61000-3-2:2006, EN 61000-3-3:2008
FCC: Part 15 Class B
LVD: EN 60950-1:2006 + A11:2009
Headend Equipment
BACK PANEL INTERFACE
ORDERING INFORMATION
Model
Tuner Type
ASI Input
-S2C
-CC
-TC
-DC
-S2T
-CT
-TT
-DT
DVB-S2
DVB-C
DVB-T
DS3/E3
DVB-S2
DVB-C
DVB-T
DS3/E3
●
●
●
●
●
●
●
●
Built-in Re-mux
●
●
●
●
●
●
●
●
ASI Output (mirrored)
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
100M TS/IP Extension Board
●
●
●
●
QAM Modulation
●
●
●
●
COFDM Modulation
●Standard
BLOCK DIAGRAM
Headend Equipment
APPLICATION
Headend Equipment
TMH-100AS
Compact modular SMATV
Headend Equipment
INTRODUCTION
TMH-100AS is a compact modular SMATV headend, supporting up to 16 channels in one 19” 4U chassis. It integrates multiple
functions including DTV signal reception, descrambling, decoding and analog modulation. TMH-100AS has various options
for RF input front end, such as DVB-S/S2/T/T2/C, ATSC, ISDB-T and DMBT etc., moreover, analog AV and IP input are also
available. Equipped with dual DVB-CI, the TMH-100AS module can decrypt multiple pay TV services and loop through the TS
to the neighbor modules through internal cables for further processing. Each TMH-100 AS module can process two MPEG-2
or H.264 HD/SD services and downscale the HD content to SD, then modulate and output via two adjacent analog RF
channels. TMH-100AS supports various analog modulation standard, such as PAL B/G, PAL D/K, NTSC, and SECAM etc. Each
TMH-100AS module can be controlled and supervised by SNMP and HTTP WEB.
MAIN FEATURES
• Support various analog modulation standard, such as PAL B/G, PAL D/K, NTSC, and SECAM etc.
• DVB-S/S2/T/T2, ATSC, ISDB-T, DMBT front end option
• Support IP input and analog AV input
• MPEG-2, H.264 HD/SD decoding
• Two adjacent analog RF channel output per module
• Dual DVB-CI for multi-decryption
• TS loop through between modules
• Functional module hot-swappable
• Web, SNMP remote control or handheld programmer unit local control
• 19” 4RU chassis compact modular design, supporting up to 8 modules in one chassis
• Redundant power supply
• Intelligent temperature control cooling system
• Stand alone function of each module
• Cost-saving by backward compatible with new modules
• On site software update through IP or USB
ORDERING INFORMATION
Product name
Model No.
Model No. Description
Professional IRD and Analog Modulator Module
TMH-170D/A
Dual Channel IRD and Analog Modulator Module
Professional Analog Modulator Module
TMH-170I/A
Dual Channel IPTV Decoder and Analog Modulator Module
Professional IPTV Decoder and Analog Modulator Module
TMH-170PALmod
Dual Channel PAL/NTSC/SECAM modulator
Headend Equipment
TMH-170D/A
DVB Tuner to Analog Trans-modulator
• Multiple RF input front end option DVB-S2/S/C/T/T2, ATSC, ISDB-T, DMBT
• Two adjacent analog channels output in range of 48-860MHz
• Output level 100dBμV per channel
• Support MPEG-2, H.264 SD/HD decoding
• Remote Control and Supervision by SNMP and HTTP WEB
• Support BISS-1, BISS-E descrambling
• Dual DVB-CI for multi-decryption
• Dynamic PMT detection and automatic updating
TMH-170I/A
Twin TS/IP to Analog Trans-modulator
• Two IP multicast/unicast input ports
• Two adjacent analog channels output in range of 48-860MHz
• Supports MPEG-2, H.264 SD/HD decoding
• Output level 100dBμV per channel
• Remote Control and Supervision by SNMP and HTTP WEB
TMH-170PALmod
Twin Analog Modulator
• 2 analog AV input
• Two adjacent analog channels output in range of 48-860MHz
• Modular design for easy installation and maintenance
• Output level 100dBμV per channel
• Remote Control and Supervision by SNMP and HTTP WEB
Headend Equipment
TMH-100
Compact modular digital
TV Headend Equipment
INTRODUCTION
TMH-100 is a compact modular digital TV headend that includes professional MPEG-2 and MPEG-4 AVC/H.264 SD/HD IRD,
MPEG-2 and MPEG-4 AVC/H.264 SD/HD Encoder/Transcoder, Re-Multiplexer, QAM/COFDM Trans-Modulator, Dual Channel
Analog Modulator, DVB Scrambler and so on. Within a 4U×19” chassis, it provides 8 slots for any type of modules and 2
redundant power supply units. Thanks for its flexibility and high density, TMH-100 offers operators the advanced headend
architectures in the marketplace for delivering analog and digital broadcast services to their subscribers. Coming with
more new modules, TMH-100 is most suitable for future multiple network architectures: streaming and multiplexing of digital
content over IP based networks and conversion of digital content for analog networks.
MAIN FEATURES
• Support various analog modulation standard, such as PAL B/G, PAL D/K, NTSC, and SECAM etc.
• DVB-S2/S, DVB-S, DVB-C, DVB-T2/T IRD modules with CI
• DVB-S/S2T/T2 to DVB-C QAM and DVB-T
• COFDM trans-modulator module
• MPEG-2, H.264 HD/SD encoder and transcoder module
• 8 Way re-multiplexer module
• DVB Simulcrypt, BISS-1, BISS-E scrambler module
• Rich interface with ASI, IP, SDI, YPbPr, CVBS, XLR
• Web, SNMP Remote Control or handheld programmer unit local control
• 4RU 19”chassis compact modular design, supporting up to 8 modules
• Functional module hot-swappable
• Redundant power supply
• Intelligent cooling system with temperature
• Stand alone function of each module
• Cost-saving by backward compatible with new modules
• On site software update through IP
Headend Equipment
ORDERING INFORMATION
Model No.
Description
TMH-100
4RU Chassis with 8 Slots
TMH-100CU
Programmer Unit
TMH-140P
Single Channel MPEG-2 SD IRD and Processor
TMH-150P
Single Channel H.264 HD IRD and Processor
TMH-130TM
Single Channel Transmodulator
TMH-130EC
Single Channel MPEG-2 SD Encoder
TMH-150EC
Single Channel H.264 HD Encoder and Transcoder
TMH-130MX
8-Way Remultiplexer
TMH-100
Main Chassis
• Standard 4 RU chassis with 8 slots for functional modules
and 2 slots for Power Supplies
• Hot-backup power supply unit
• Intelligent cooling system with temperature sensor
• Wall mounted or Rack mounted
• Compatible with new successive modules
• Power Supply: AC 90V-250V, 150Watts, 50-60Hz
• Optional Build-in IP Switch
• Dimension: L=340mm, W=483mm, H=178mm (4U)
• Operating temperature: 0 ~ 45°C (for all modules)
• Storage temperature: -10 ~ 60°C (for all modules)
TMH-100CU
Programmer unit
• 2×20 LCD display screen and 6-key keypad
• No external power nor battery needed
• Easy and quick on site system configuration without PC
• Compatible with new modules
• Dimension 170×70×22 mm
Headend Equipment
TMH-140P
Single Channel MPEG-2 SD IRD and Processor
• Multiple inputs DVB-S2/S/C/T, TS/IP and ASI
• SD MPEG-2 MP@ML digital Video decoding
• Flexible built-in re-multiplexing between ASI,
Tuner and TS/IP Inputs
• 2x DVB-CI Slots, Multi Programs,
BISS-1 and BISS-E decryption
• Dynamic PMT detection and automatic updating
• UDP, RTP Multicast / Unicast IP output,
supports up to 32 independent channels
• PCM audio embedded in SDI output
• Remote Control and Supervision by SNMP,
HTTP WEB and Proprietary HDMS software
• RSSI, received Eb/No & BER monitoring
• On Site software update through IP
SPECIFICATION
DVB-T Tuner Input
DVB-S/S2 Tuner Input
Connector Type Input Frequency Range Input Level Symbol Rate Roll-off Factor FEC Code Rate LNB Polarization LNB Band Switching Tone 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
950 ~ 2150MHz
-25 ~ -65dBm
DVB-S QPSK: 5~45MS/s;
DVB-S2 8PSK 10~31MS/s
DVB-S QPSK: 0.35; DVB-S2
8PSK: 0.35, 0.25, 0.2
DVB-S2 8PSK: 2/3, 3/4, 3/5, 5/6, 8/9, 9/10
DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 6/7, 7/8
0, 13V, 18V selectable
0/22KHz selectable
DVB-S Tuner Input
Connector Type Input Frequency Range Input Level Symbol Rate Roll-off Factor Puncture Rate LNB Polarization LNB Band Switching Tone 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
950 ~ 2150MHz
-25 ~ -65dBm
2 ~ 45MS/s
0.35
1/2, 2/3, 3/4, 5/6, 7/8
0, 13V, 18V selectable
0/22KHz selectable
DVB-C Tuner Input
Connector Type Input Frequency Range Symbol Rate Constellation Input Level Bandwidth Input Return Loss 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
48~860MHz
1 ~ 7MS/s (ITU J.83 Annex A)
64/128/256 QAM
-15 ~ 15dBmV
6/7/8MHz
7dB (typ.)
Connector Type Input Frequency Range Input Level Constellation Carrier Bandwidth FTT Mode Guard Interval FEC Code Rate 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
174 ~ 230MHz (VHF); 470~860MHz (UHF)
-20 ~ -70dBm
QPSK, 16-QAM, 64-QAM
6/7/8 MHz
2K/8K
1/4, 1/8, 1/16, 1/32
1/2, 2/3, 3/4, 5/6, 7/8
ASI Input
Connector Standard Input Bit Rate Package Length 1×BNC Female, 75Ω
DVB-ASI, EN50083-9
≤ 100Mb/s
188 or 204 Bytes
TS over IP (for 140 P series)
Connector Type Useful bit rate Protocol 1×RJ45, 10/100M for TS/IP
70Mb/s for 10/100M
UDP / RTP, Multicast / Unicast, IGMPv2, ARP
TS Processing
TS Input Management TS Output Management PSI/SI Descrambler Common Interface Remux and demux between Tuner,
ASI and TS/IP Inputs
Remux and demux for 2 mirror ASI outputs
Service and PID management Remux, filtering and remapping
PSI/SI table regeneration, NIT and SDT
edition, LCN Edition and Re-generation
DVB Common Scrambling Algorithm (CSA)
Double PCMCIA slots, compatible
with major CA CAMs in the market
Headend Equipment
ASI Output
Connector Type Standard Output Bit Rate Digital Audio Processing
2×BNC Female, 75Ω
(one connector is shared with SDI output)
DVB-ASI, EN50083-9
≤ 99Mb/s
Number of Output Analog Video Output
CVBS Connector Video Standard Digital Video Processing
Video Standard Video Bit Rate MPEG-2(MP@ ML)
SDI Video Resolution 576i×25, 480i×29.97
< 80Mb/s
1×BNC, 1×2.5mm phone jack
(with phone jack to RCA adaptor)
NTSC, PAL, and SECAM
Analog Audio Output
Connector Type 1×2.5mm phone jack for CVBS
and stereo audio
Number of Output 1 pair of stereo audio
SD-SDI Output
Connector Type Serial Interface Level Audio Embedded 1 pair of stereo audio output
(1 Audio PID is decoded)
1×BNC Female, 75Ω
(share with one of the two ASI outputs)
SMPTE 259M, 270 Mb/s (10bit)
800mV p-p
Yes
Control & Monitoring
Connector Type Remote Control Local Control Software Upgrade 1× RJ45, 10/100M, for equipment IP Control
SNMP, HTTP Web, Proprietary HDMS
(Network System Management Software)
Handheld Programmer Unit
FTP loader
ORDERING INFORMATION
Model
140P-S
140P-S2
140P-C
140P-T
140P-44S
140P-44S2
140P-44C
140P-44T
Tuner
-S
-S2/S
-C
-T
-S
-S2/S
-C
-T
ASI Input
●
●
●
●
●
●
●
●
Common Interface
×2
×2
×2
×2
×2
×2
×2
×2
Built-in Re-mux
●
●
●
●
●
●
●
●
ASI-Output
●
●
●
●
●
●
●
●
SDI
●
●
●
●
●
●
●
●
YPbPr
●
●
●
●
●
●
●
●
Audio L/R
●
●
●
●
●
●
●
●
CVBS
●
●
●
●
●
●
●
●
TS/IP(Max.6 SPTS or MPTS output)
●
●
●
●
●
●
●
●
TS/IP(Max.32 SPTS or MPTS output)
● Standard
Headend Equipment
TMH-150P
Single Channel H.264 HD IRD and Processor
• Multiple inputs DVB-T2/S2/S/C/T/T2, TS/IP and ASI
• Redundant inputs between Tuner, ASI and TS/IP
• SD/HD MPEG-2 and MPEG-4/H.264 digital Video decoding
• Digital Audio decoding and loop through via
• Multiple Analog and Digital Outputs, ASI, CVBS, YPbPr, SDI, TS/IP
• Flexible re-multiplexing between 2×ASI, Tuner and TS/IP Inputs
• 2×DVB-CI Slots, Multi Programs, BISS 1 and BISS E decryption
• Dynamic PMT detection and automatic updating
• Support VBI TELETEXT, EBU/ DVB Subtitle, Closed Caption
• UDP/RTP & Unicast/Multicast SPTS and MPTS over IP I/O
• Remote Control and Supervision by SNMP, HTTP WEB and
Proprietary HDMS software
• PCM audio embedded in SDI output
• On Site software update through IP
• RSSI, received Eb/No & BER monitoring
SPECIFICATION
DVB-S/S2 Tuner Input
Connector Type 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
Input Frequency Range 950~2150MHz
Input Level -25~-65dBm
Symbol Rate 5~45MS/s for QPSK
10~31MS/s for 8PSK
Roll-off Factor DVB-S QPSK: 0.35; DVB-S2
8PSK: 0.35, 0.25, 0.2
Punctured Rates DVB-S QPSK:1/2, 3/5, 2/3, 3/4, 4/5,
5/6, 8/9, 8/10
DVB-S2 8PSK:3/5, 2/3, 3/4, 5/6, 8/9, 9/10
LNB Polarization 0, 13V, 18V selectable
LNB Band Switching Tone 0/22KHz selectable
DiSEqC DiSEqC 1.0
DVB-C Tuner Input
Connector Type Input Frequency Range Input Level Symbol Rate Constellation Bandwidth Input Return Loss 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
48~860MHz
45~75dBuV
1~7MS/s (ITU J.83 Annex A)
64/128/256 QAM
6/7/8MHz
7dB (typ.)
DVB-T/T2 Tuner Input
Connector Type Input Frequency Input Level Constellation Bandwidth FTT Mode 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
104~862MHz (VHF/UHF)
-20~-70dBm (Quasi Error Free, QEF)
DVB-T: QPSK/16-QAM/64-QAM
DVB-T2: QPSK, 16QAM, 64QAM, 256QAM
6/7/8 MHz
DVB-T: 2K/8K
DVB-T2: 1K, 2K, 4K, 8K, 16K, 32K
Guard Interval DVB-T: 1/4, 1/8, 1/16, 1/32
DVB-T2: 1/4, 5/32, 1/8, 5/64, 1/16, 1/32,
1/64, 1/128
FEC Code Rate DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-T2: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6
Input return loss 7dB (typ.)
ASI Input
Connector Type Standard Input Bit Rate
Package Length 1×BNC Female, 75Ω
DVB-ASI, EN50083-9
≤ 100Mb/s
188 or 204 Bytes
TS over IP
Connector Type Useful bit rate Protocol 1×RJ45, 10/100M for TS/IP
70Mb/s for 10/100M
UDP / RTP, Multicast / Unicast, IGMPv2, ARP
TS Processing
TS Input Management Remux and demux between Tuner,
ASI and TS/IP Inputs
TS Output Management Remux and demux for 2 independent
ASI outputs
Service and PID mgmt. Remux, filtering and remapping
PSI/SI PSI/SI table regeneration, NIT and SDT
edition, LCN Edition and Re-generation
Descrambler DVB Common Scrambling Algorithm (CSA)
BISS Mode BISS-1, BISS-E
Common Interface Double PCMCIA slots, compatible with major CA CAMs in the market
ASI Output
Connector Type Standard TS Processing 2×BNC Female, 75Ω
DVB-ASI, EN50083-9
2 Independent TS Re-multiplexing from
tuner, TS/IP and 2 ASI inputs
Headend Equipment
Analog Audio Output
Digital Video Processing
Video Standard SDI Video Resolution Video Bit Rate SDI Connector Type SD-SDI Serial Interface HD-HDI Serial Interface Level MPEG-2(MP@ ML for SD, MP@HL for HD)
MPEG 4/H.264 AVC Part 10
(MP@L3 for SD, HP@L4.1 for HD)
1080i×30, 1080i×29.97, 1080i×25, 720p×60
720p×59.94, 720p×50, 576i×25, 480i×29.97
< 80Mb/s
1×BNC Female, 75Ω
SMPTE 259M, 270 Mb/s (10bit)
SMPTE 292M, 1.485 Gbit/s (10bit)
800mV p-p
Connector type Output mode Baseband Data Output
Subtitle DVB/EBU
VBI Teletext, WSS, VFD, VPS
Closed Caption EIA 608, EIA 708, EIA 608-to-708
Redundancy
Redundancy Port Switching Condition Switching Mode Digital Audio Processing
Number of Output 1 pair of audio outputs
Analog Video Output
YPbPr Connector CVBS Connector Video Standard YPbPr Resolution Signal Level Frequency Response Chroma-Luma Delay
Field Time Distortion Line Time Distortion Short Time distortion Differential Gain Differential Phase Signal to Noise Ratio 1×2.5mm phone jack, 75Ω
(with phone jack to RCA adaptor,)
Left, Right, Dual Mono, Stereo
Between Tuner, ASI inputs and TS/IP
TS Sync Loss
Main, Spare
Control & Monitoring
1×2.5mm phone jack, 75Ω
(with phone jack to RCA adaptor,)
1×2.5mm phone jack, 75Ω
(with phone jack to RCA adaptor,)
NTSC, PAL, and SECAM
1080i×30, 1080i×29.97, 1080i×25, 720p×60,
720p×59.94, 720p×50, 480p×60, 576p×50, 576i×25, 480i × 29.97
I.0 Vp-p±5%
< ±I dB at 5.5 MHz
<±30 ns
<2%
<1%
<2%
<4%
<2°
>55 dB (luminance weighted)
Connector Type Remote Control Local Control Equipment Upgrade 1×RJ45, 10/100M, for equipment IP Control
SNMP, HTTP Web, Proprietary HDMS
Network System Management Software
Handheld Programmer Unit
FTP loader
ORDERING INFORMATION
Model
150P-30S2
150P-30C
150P-30T
150P-30T2
150P-44S2
150P-44C
150P-44T
150P-44T2
Tuner
-S2/S
-C
-T
-T2
-S2/S
-C
-T
-T2
ASI Input
●
●
●
●
●
●
●
●
Common Interface
×2
×2
×2
×2
×2
×2
×2
×2
Built-in Re-mux
●
●
●
●
●
●
●
●
ASI-Output
×2
×2
×2
×2
×2
×2
×2
×2
SDI
●
●
●
●
●
●
●
●
YPbPr
●
●
●
●
●
●
●
●
Audio L/R
●
●
●
●
●
●
●
●
CVBS
●
●
●
●
TS/IP(Max.32 SPTS or MPTS output)
● Standard
●
●
●
●
●
●
●
●
Headend Equipment
TMH-130TM
Single Channel Transmodulator
• DVB-S2/S, DVB-C or DVB-T Tuner Input
• ASI input and output
• Flexible re-multiplexing between ASI and Tuner inputs
• PSI/SI adapting and re-generation, including NIT insertion,
LCN insertion etc.
• Service Drop or PID filtering and Re-mapping
• Remote Control and Supervision by SNMP,
HTTP WEB and Proprietary HDMS sw.
• On Site software update through IP
• RSSI, received Eb/No & BER monitoring
SPECIFICATION
DVB-S/S2 Tuner Input
TS Processing
Connector Type 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
Input Frequency Range 950~2150MHz
Input Level -25~-65dBm
Symbol Rate DVB-S QPSK: 5~45MS/s;
DVB-S2 8PSK: 10~31MS/s
Roll-off Factor DVB-S QPSK: 0.35; DVB-S2
8PSK: 0.35, 0.25, 0.2
Punctured Rates DVB-S2 8PSK: 2/3, 3/4, 3/5, 5/6, 8/9, 9/10
DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 6/7, 7/8
LNB Polarization 0, 13V, 18V selectable
LNB Band Switching Tone 0/22KHz selectable
DVB-C Tuner Input
Connector Type Input Frequency Range Symbol Rate Constellation Input Level Bandwidth Input Return Loss 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
48~860MHz
1~7MS/s (ITU J.83 Annex A)
64/128/256 QAM
-15~15dBmV
6/7/8MHz
7dB (typ.)
DVB-T Tuner Input
Connector Type Input Frequency Range Input Level Constellation Carrier Bandwidth FTT Mode Guard Interval FEC Code Rate 1×F type female 75Ω for Input,
1×F type female 75Ω for loop through outp.
174~230MHz (VHF); 470~860MHz (UHF)
-20~-70dBm
QPSK, 16-QAM, 64-QAM
6/7/8 MHz
2K/8K
1/4, 1/8, 1/16, 1/32
1/2, 2/3, 3/4, 5/6, 7/8
ASI Input
Connector Type Standard Input Bit Rate Package Length 1×BNC Female, 75Ω
DVB-ASI, EN50083-9
≤ 100Mb/s
188 or 204 Bytes
TS Input Management Service and PID mgmt.. PSI/SI Remux demux between Tuner & ASI Inputs
Remux, filtering and remapping
PSI/SI table regeneration, NIT and SDT
edition, LCN Edition and Re-generation
ASI Output
Connector Type 1×BNC Female, 75Ω
Standard DVB-ASI, EN50083-9
TS Processing 2 mirror TS Re-multiplexing from Tuner
and ASI inputs
DVB-C Re-Modulation
Constellation Symbol Rate I/Q Amplitude Error I/Q Phase Error Phase jitter MER J.83 Annex A: 16/32/64/128/256QAM;
J.83 Annex B: 64/256QAM
3~7.2MS/s
< 0.3%
< 0.3°
< 0.5°RMS
> 35dB
DVB-T Re-Modulation
Constellation QPSK/16QAM/64QAM
Bandwidth 5/6/7/8MHz
FFT Mode 2K
Guard Interval 1/4, 1/8, 1/16, 1/32
Code Rate 1/2, 2/3, 3/4, 5/6, 7/8
MER >36dB
RF Output
Connector Type Output Frequency Range Output Level Spurious Rejection Output Return Loss F type female, 75Ω
48~860MHz agile, step by 10 KHz
97~110dBμV, step by 1dBμV
55dB (typ.)
12dB (typ.)
Control & Monitoring
Connector Type Remote Control Local Control Software Upgrade 1×RJ45, 10/100M, for equipment IP Control
SNMP, HTTP Web, Proprietary HDMS
(Network System Management Software)
Handheld Programmer Unit
FTP loader
Headend Equipment
ORDERING INFORMATION
Model
130TM-S2C
130TM-CC
130TM-TC
Tuner
130TM-AC
130TM-S2T
130TM-CT
130TM-TT
150P-44T2
-S2/S
-C
-T
-S2/S
-C
-T
-T2
ASI Input
●
●
●
●
●
●
●
●
Built-in Re-mux
●
●
●
●
●
●
●
●
ASI-Output
●
●
●
●
●
●
●
×2
QAM modulation
●
●
●
●
COFDM modulation
●
● Standard
TMH-130MX
Re-multiplexer Module
• 8-way SPTS or MPTS ASI inputs
• Redundant ASI outputs
• PSI/SI table regeneration, NIT and SDT edition,
LCN Edition and Re-generation
• Remote Control and Supervision by SNMP
and Proprietary HDMS software
• On Site software update through IP
SPECIFICATION
ASI Input
Connector Type Input Bit Rate Data transmission mode Packet Length 8×BNC Female, 75Ω
≤ 100Mb/s
BYTE or BURST mode auto-detection
188 /204 bytes, auto-detection
ASI Output
Connector Type Output bit rate Data transmission mode Packet Length Signal Level ●
2×BNC Female, 75Ω
≤ 99Mb/s
Byte
188 or 204 Bytes
800mVpp±10%
Control & Monitoring
Connector Type 1×RJ45, 10/100M, for equipment IP Control
Remote Control SNMP, Proprietary HDMS network
Management Software
Local Control Handheld Programmer Unit
Software Upgrade FTP loader
●
●
●
Headend Equipment
TMH-130EC
Single Channel MPEG-2 SD Encoder
• Digital SDI with embedded digital audio input
• Analog Composite Video for PAL/NTSC/SECAM Input
• MPEG-2 MP@ML Video encoding
• User configurable GOP
• User configurable 4:3/16:9 aspect ratio
• PAT, PMT and SDT generation and NIT Insertion
• 10/100M IP Output, UDP/RTP & Unicast/Multicast SPTS and MPTS
• Remote Control and Supervision by SNMP,
HTTP WEB and Proprietary HDMS software
SPECIFICATION
Video Compression
Analog Input Digital Input Compression Standard Video Resolution Aspect Ratio Video output Bit rate TS over IP Output
Analog NTSC, PAL and SECAM
SD-SDI (SMPTE-259M)
MPEG-2 MP@ML
480i (720x480) @29.97Hz: SMPTE125M
576i (720x576) @25Hz: ITU-R BT.656-4
4:3/16:9 selectable
1.5 ~ 20Mb/s
Audio Compression
Audio Channels Audio Sampling Rate Audio Output Bit rate 1 pair of stereo
32, 44.1, 48 KHz
32, 64, 128, 192, 256, 384 Kb/s
ASI Output Interface
Connector Type Output bit rate Packet Length Signal Level RCA female, Stereo L/ R
RCA female, 75Ω
1×BNC female, 75Ω
Group 1 to 4 selectable
2×BNC Female, 75Ω
≤ 99Mb/s
188 / 204 Bytes
800mVpp±10%
Control & Monitoring
onnector Type Remote Control Local Control Software Upgrade Audio/Video Input Interface
Analog Audio Analog CVBS SD-SDI SDI embed audio Connector Type 1×RJ45, 10/100M for TS/IP
Useful bit rate 70Mb/s for 10/100M
Protocol UDP / RTP, Multicast / Unicast, IGMPv2
ARP
1×RJ45, 10/100M, for equipment IP Control
SNMP, HTTP Web, Proprietary HDMS
(Network Management Software)
Handheld Programmer Unit
FTP loader
TS Processing
TS Output Management PSI/SI Remux and demux for mirror ASI outputs
Service and PID management
Remux, filtering and remapping
PSI/SI table regeneration, NIT and SDT edition
ORDERING INFORMATION
Model
130EC-30
130EC-40
CVBS
●
●
SD-SDI Input
●
●
ASI Output
×2
×2
TS/IP Output
● Standard
●
Headend Equipment
TMH-150EC
Single Channel H.264 HD Encoder and Transcoder
• Multiple video resolution including 1080i, 720p, 576i and 480i
• Multiple inputs HDMI, HD/SD-SDI, and CVBS for encoding
• ASI and IP Input for Trans-coding
• Support 10/100M TS/IP SPTS and MPTS
• Built-in re-multiplexer for encoder loop
• Support VBR and CBR encoding mode
• Digital audio pass through for trans-coding
• Support 2 pairs of analog stereo audio encoding
with optional extension board
• Remote Control and Supervision by SNMP,
HTTP WEB & Proprietary HDMS software
SPECIFICATION
Video Compression
Video Resolution
Compression Standard Aspect Ratio Video Encoding bit rate ASI Input
1080i (1920/1440×1080) @25Hz,
29.97Hz, 30Hz: SMPTE274M
720p (1280×720) @50Hz, 59.94Hz,
60Hz: SMPTE296M (for 150EC only)
480i (720×480) @29.97Hz: SMPTE125M
576i (720×576) @25Hz: ITU-R BT.656-4
H.264, High Profile Level 4.0
4:3/16:9 selectable
2Mb/s-20Mb/s
Audio Compression
Audio Input Audio Channels Sampling rate Audio compression bit rate Embedded Audio, Analog audio
1 pair of stereo
48KHz
16~256Kb/s
Audio/Video Input Interface
Analog Audio Analog CVBS HD-SDI HDMI 1×2.5mm phone jack, Stereo L/ R
(with phone jack to RCA adaptor)
1×2.5mm phone jack
(with phone jack to RCA adaptor)
1×BNC Female, 75Ω
1×HDMI 1.3 interface
Connector Type Input bit rate Packet Mode Packet Length 1×BNC Female, 75Ω
≤ 100Mb/s
Byte
188/204 Bytes
TS Processing
TS Input Management TS Output Management Service and PID mgmt.. PSI/SI Remux & demux between ASI input & SPTS
Remux and demux for mirror ASI outputs
Remux, filtering and remapping
PSI/SI table regeneration,
NIT and SDT edition
TS over IP
Connector Type Useful bit rate Protocol Source 1×RJ45, 10/100M for TS/IP
70Mb/s for 10/100M
UDP / RTP, Multicast / Unicast, IGMPv2, ARP
Built-in Re-mux, ASI input, Encoder
ASI Output Interface
Connector Type Output bit rate Packet Length Signal Level 2×BNC Female, 75Ω
≤ 99Mb/s
188 / 204 Bytes
800mVpp±10%
Control & Monitoring
ORDERING INFORMATION
Model
Connector Type Remote Control Local Control Software Upgrade 1×RJ45, 10/100M, for equipment IP Control
SNMP, HTTP Web, Proprietary HDMS
Handheld Programmer Unit
FTP loader
150EC
HD-SDI Input
●
SD-SDI Input
●
HDMI Input
●
CVBS
●
ASI Input
●
Built-in Re-mux
●
ASI Output
×2
TS/IP I/O
●
● Standard
For in depth information please visit our webpage
Für mehr Information bitte besuchen Sie unsere Webseite
AG
Bahnhofstrasse 10.
CH, 6302 Zug
Switzerland
teletronik@teletronik.com
www.teletronik.com
Your local distributor:
© 27 05 2016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising