advertisement
2
Microsoft, Windows, and PowerPoint are trademarks or registered trademarks of Microsoft Corporation in the U.S. and other countries.
Google, Google logo, and Google Translate are trademarks or registered trademarks of Google Inc.
NEC is a registered trademark of NEC Corporation.
All product/brand names are trademarks or registered trademarks of the respective holders.
Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
Please be advised that Fuji Xerox Co,. Ltd. can assume no responsibility regarding malfunctions or damage that arise due to computer viruses or illegal access.
Important
1. This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied or modified in whole or part, without the written consent of the publisher.
2. Parts of this manual are subject to change without prior notice.
3. We welcome any comments on ambiguities, errors, omissions, or missing pages.
Xerox, Xerox and Design, Fuji Xerox and Design as well as CentreWare are registered trademarks or trademarks of Xerox Corporation in Japan and/or other countries.
DocuWorks, and Scan Translation Service are registered trademarks or trademarks of Fuji Xerox Co., Ltd..
Scan Translation Service uses NEC English-Japanese / Japanese-English translation engine when translating English into Japanese and Japanese into English.
Scan Translation Service uses Google Translate
TM
API when translating languages other than English-Japanese and Japanese-English.
Introduction
Introduction
Thank you very much for choosing Scan Translation Service.
When using Scan Translation Service with a Fuji Xerox multifunction device, you will need to install the "Tool to Link Multifunction Devices to Scan Translation Service" (hereinafter referred to as "Multifunction Device Linkage Tool") into the applicable multifunction device.
This manual describes how to install the Multifunction Device Linkage Tool and how to make environment settings for the multifunction device.
Furthermore, this manual assumes that you have a basic knowledge of your multifunction device and know how to operate it. Refer to the "Administrator Guide" and "User Guide" that were packaged with your multifunction device for details on how to operate your device.
Fuji Xerox Co., Ltd.
3
4
Table of Contents
Manual Organization
Manual Organization
The manuals that describe how to setup and use Scan Translation Service are as follows.
z
Scan Translation Service User Guide
This manual describes the functions and operating procedures for using Scan Translation
Service.
z
Scan Translation Service Administrator Guide
This manual describes the administration functions and operating procedures for using
Scan Translation Service when logged in with administrator permissions.
z
Scan Translation Service Multifunction Device Linkage Setup Guide (this manual)
This manual describes how to install and setup the tool for linking multifunction devices to Scan Translation Service.
5
How to Use This Manual
How to Use This Manual
6
Structure of This Manual
1. Overview
This section provides an overview of Scan Translation Service.
2. Before Installing the Tool
This section describes the advanced verification and environment settings that need to be made when installing the Multifunction Device Linkage Tool.
3. Installation Process
This section describes the installation process of the Multifunction Device Linkage Tool.
Notation Used in This Manual
The following shows the notation used in this manual.
"
[
<
{
>
"
]
>
}
Indicates a keyboard key.
Exampl e:
Press the <Enter> key.
Indicates menus, buttons, tabs, and items displayed on the screen.
Exampl e:
Click the [Apply] tab.
Indicates values that change during operation such as usernames and server names.
Exampl e:
Click [{User Name}].
Indicates the breadcrumb hierarchy of the menu or Web page.
Exampl e:
Select [Connection Definition] > [Connection Destination 1] from the [File] menu.
Indicates a reference point in the manual and references to other manuals.
It can also represent messages or emphasized words.
Exampl e:
Indication is made such as "1 Overview" or
"Name is not specified."
Describes important points.
Describes additional useful information.
Describes operating procedures.
z
The Microsoft
®
Windows
®
Operating System is referred to as "Windows".
z
A personal computer is referred to as a "PC".
z
Clicking the right button on a mouse is referred to as a "right click".
How to Use This Manual
7
How to Use This Manual
8
1. Overview
This section provides an overview of Scan Translation Service and explains its major functions.
1. Overview
Overview
Scan Translation Service is a cloud-based translation service that can be used via an
Internet connection from either a multifunction device or PC.
By using this Service, you can scan a paper document as if to copy it via your multifunction device and create a translated document that preserves the exact same layout as the source document.
In like manner, you can translate electronic documents from your PC.
Since the page layout of the translated document is exactly the same as the source document, translated results are extremely easy to view and reference, which enables you to understand the main details of the document quickly.
Important
• This Service is a machine translation service, and therefore, the accuracy of the translated result may not always be satisfactory. It is possible to improve the accuracy of the translation by utilizing a custom User Dictionary. (The User Dictionary can only be used when translating from either Japanese to English or English to Japanese.)
The main functions of the Service are as follows.
(1) Translation of paper documents
You can make a machine translation of your paper documents by scanning them with your multifunction device. (Thai language documents cannot be translated on multifunction device.)
(2) Print translation result output
You can print out the results of the machine translation from your multifunction device.
(3) Translation of electronic documents
The following electronic documents are uploaded using a Web browser and are machine translated. Thai, Vietnamese, Indonesian and Malay language DocuWorks documents cannot be translated.
z
DocuWorks document z
PDF document z
Microsoft Word document z
Microsoft PowerPoint
®
document
(4) Downloading the Translated Result
The result of the translation can be downloaded as an electronic document.
(Downloading to mobile devices can also be carried out.)
9
1. Overview
(5) Editing the User Dictionary
Registering a User Dictionary can improve translation accuracy. (The User Dictionary can only be used when translating from either Japanese to English or English to Japanese.)
(6) Service Usage Administration
Customers with administrator permissions can perform the following operations using a
Web browser.
- Register and delete users
- Grant and delete permissions of administrators
- Register and delete groups
- Aggregate usage status of the Service
- Change the automatic deletion period for translated results
- Make administrator e-mail notification settings
10
2. Before Installing the Tool
2. Before Installing the Tool
This section provides explanation on the preparation that needs to be taken before installing the Multifunction Device Linkage Tool.
Before installing the Multifunction Device Linkage Tool, it is necessary to carry out advanced verification and make environment settings for the applicable multifunction device.
Note
• Please note that the screenshots displayed in this manual may display different items and provide different usage functions depending on the type of multifunction device being used.
Verifying If a Device is Applicable
Please refer to the following link on our official company website for information regarding models that can use the "Function to Link Multifunction Devices to Scan
Translation Service".
z
For users who concluded a Scan Translation contract in Japan http://www.fujixerox.co.jp/solution/scantrans/ z
For users who concluded a Scan Translation contract in a country other than Japan http://www.fxap.com.sg/product/software/scanservice/index.jsp
11
2. Before Installing the Tool
Single Sign On Function
The following models support the Single Sign On function.
Note
• Some models may not be available in your country or region.
z
DocuCentre-V C2265/C2263 z
ApeosPort-V 3065/3060/2060 z
DocuCentre-V 3065/3060/2060 z
ApeosPort-V C7776/C6676/C5576/C4476/C3376/C3374/C2276 z
DocuCentre-V C7776/C6676/C5576/C4476/C3376/C3374/C2276 z
ApeosPort-V C7785/C6685/C5585 z
DocuCentre-V C7785/C6685/C5585 z
ApeosPort-V C7780 / C6680 / C5580
(*1) z
DocuCentre-V C7780 / C6680 / C5580
(*1) z
ApeosPort-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373 / C2275
(*1) z
DocuCentre-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373 / C2275
(*1) z
ApeosPort-V C3320 z
DocuPrint CM415 AP z
Color C70 / C60 z
Versant 80 Press z
ApeosPort-V 7080/6080 z
DocuCentre-V 7080/6080 z
ApeosPort-V 5070 / 4070 z
DocuCentre-V 5070 / 4070 z
ApeosPort-V 4020 z
DocuPrint M465 AP
Note
• For more information on the Single Sign On function, see "Single Sign On Function
12
(*1) These include later models (T2).
2. Before Installing the Tool
Installation
The Multifunction Device Linkage Tool compatible with the Single Sign On function is already installed on the following models.
Note
• Some models may not be available in your country or region.
z
DocuCentre-V C2265/C2263 z
ApeosPort-V 3065/3060/2060 z
DocuCentre-V 3065/3060/2060 z
ApeosPort-V C7776/C6676/C5576/C4476/C3376/C3374/C2276
(*2) z
DocuCentre-V C7776/C6676/C5576/C4476/C3376/C3374/C2276
(*2) z
ApeosPort-V C7785/C6685/C5585
(*2) z
DocuCentre-V C7785/C6685/C5585
(*2)
You do not need to install the tool. Execute the following procedure only.
z
"Multifunction Device Advanced Verification" (P.14)
z
"Multifunction Device Environment Settings" (P.16)
The Multifunction Device Linkage Tool not compatible with the Single Sign On function is already installed on the following models.
Note
• Some models may not be available in your country or region.
z
ApeosPort-V C7776/C6676/C5576/C4476/C3376/C3374/C2276
(*3) z
DocuCentre-V C7776/C6676/C5576/C4476/C3376/C3374/C2276
(*3) z
ApeosPort-V C7785/C6685/C5585
(*3) z
DocuCentre-V C7785/C6685/C5585
(*3) z
ApeosPort-V C7780 / C6680 / C5580
(*4) z
DocuCentre-V C7780 / C6680 / C5580
(*4) z
ApeosPort-V C7775/C6675/C5575/C4475/C3375/C3373/C2275
(*4) z
DocuCentre-V C7775/C6675/C5575/C4475/C3375/C3373/C2275
(*4)
(*2) The Multifunction Device Linkage Tool compatible with the Single Sign On function is installed when Contents ROM version is 2.0.0 or later. Check [Software version] screen of your multifunction device to confirm the Contents ROM version. For the details on how to display
[Software version] screen, please refer to the "Administrator Guide" provided with your multifunction device package.
(*3) The Multifunction Device Linkage Tool not compatible with the Single Sign On function is installed when Contents ROM version is 1.x.x. Check [Software version] screen of your multifunction device to confirm the Contents ROM version. For the details on how to display
[Software version] screen, please refer to the "Administrator Guide" provided with your multifunction device package.
(*4) It is installed only for later models (T2). You can confirm whether or not your multifunction device is a later model (T2) by checking the label inside the front cover.
13
2. Before Installing the Tool z
ApeosPort-V C3320 z
DocuPrint CM415 AP z
ApeosPort-V 7080/6080 z
DocuCentre-V 7080/6080 z
ApeosPort-V 4070 / 3070 z
DocuCentre-V 4070 / 3070 z
ApeosPort-V 4020 z
DocuPrint M465 AP
If not using the Single Sign On function, you do not need to install the tool.Execute the following procedure only.
z
"Multifunction Device Advanced Verification" (P.14)
z
"Multifunction Device Environment Settings" (P.16)
If you will be using the Single Sign On function, you must reinstall Multifunction Device
Linkage Tool, which supports the Single Sign On function.
Multifunction Device Advanced Verification
The Multifunction Device Linkage Function can operate under the following environments. If the environment of your model does not meet the requirements, upgrade your device with the necessary options.
z
Internal hard disk drive
This step is not required if using one of the following models. Also, the confirmation at step 3 is not necessary.
- DocuCentre-V C2265/C2263
- DocuCentre-V 3065/3060/2060 z
System memory of at least 2GB
The following explains how to check the environment of your model.
14
0
Confirmation of Hard Disk and System Memory
Steps
1
Press the <Machine Status> button on the control panel of the multifunction device.
2
Select [Machine Configuration] on the [Machine Information] tab.
3
Confirm the items under [Hard Disk].
(*5)
If [{Yes}] is displayed, the item is available.
(*5) This step is not required if using one of the following models. (DocuCentre-V C2263/C2265,
DocuCentre-V 2060/3060/3065)
2. Before Installing the Tool
4
Confirm the items under [System Memory Size].
If the device already has more than the necessary amount of memory, there is no need to upgrade the memory.
5
Press [Close] twice.
15
2. Before Installing the Tool
Multifunction Device Environment Settings
To use the Multifunction Device Linkage Tool, it is necessary to carry out the following settings on the multifunction device.
Note
• Some models may not be available in your country or region.
Verification of External Access
Kit
Item
Password Setting for Software
Options
SOAP Port Setting
Protocol Setting
Proxy Server Setting
Web Browser Setting
Plug-in Settings
Confirmation/Setting Content
These steps can only be performed for multifunction devices of the following models.
• ApeosPort-IV C7780 / C6680 / C5580
• ApeosPort-IV C5570 / C4470 / C3370 / C3371 / C2270
• ApeosPort-IV C4430
• ApeosPort-IV 5070 / 4070 / 3070
• ApeosPort-IV 2060 / 3060 / 3065
These steps can only be performed for multifunction devices of the following models.
• ApeosPort-V C7780 / C6680 / C5580
(*1)
• DocuCentre-V C7780 / C6680 / C5580
(*1)
• ApeosPort-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373 /
C2275
(*1)
• DocuCentre-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373
/ C2275
(*1)
• ApeosPort-V C3320
• DocuPrint CM415 AP
• ApeosPort-IV C5575 / C4475 / C3375 / C3373 / C2275
• DocuCentre-IV C5575 / C4475 / C3375 / C3373
• Color C70 / C60
• Versant 80 Press
• ApeosPort-V 7080/6080
• DocuCentre-V 7080/6080
• ApeosPort-V 5070 / 4070
• DocuCentre-V 5070 / 4070
• ApeosPort-V 4020
• DocuPrint M465 AP
• ApeosPort-IV 7080 / 6080
• DocuCentre-IV 7080 / 6080
• SOAP port: [Enabled]
• Port number: [80]
• IP address, subnet mask, and gateway address: settings for the use in TCP/IP network environment
• DNS Server Setup: DNS server address setting
• Settings for using devices in an HTTPS environment such as server name, port number, log-in name, and password
• Enable File Printing: [Yes]
• Accept Cookies: [Yes] or [Warn user when cookie is offered]
• Use TLS1.0: [Yes]
• Embedded Plug-ins: [Enabled]
(*1) These include later models (T2).
16
2. Before Installing the Tool
Note
• For information regarding the details of each item, please refer to the "Administrator
Guide" provided with your multifunction device package.
• If you will use the Single Sign On function, you must have registered an authenticated user using the authentication function on the multifunction device.For more information, refer to the "Administrator Guide" provided with your multifunction device package.
• For secure network communication, set [Verify Remote Server Certificate] to [Enabled], and then import the CA certificate of Scan Translation Service to the machine. For details about how to import the CA certificate, refer to "Security Function Supplementary Guide" provided with the machine. For how to get the CA certificate, refer to "Self Help" on the following URL:
- For users who concluded a Scan Translation Service contract in Japan
http://www.fujixerox.co.jp/support/service/scantrans/index.html
- For users who concluded a Scan Translation Service contract in a country other than
Japan
http://www.fxap.com.sg/product/software/scanservice/index.jsp
• When using SSL/TLS communication also for other features or services, the machine requires the certificates of them as well. If you need to configure the connection of those features or services by yourself, get the certificates from the system administrators of their servers, and then import them to the machine. For details about the services for Fuji
Xerox or third-party servers, refer to the user documentation of each service.
0
Confirmation of Each Item/Setting Method
Confirm the environment settings on the control panel of the multifunction device.
The confirmation/setting of each item is carried out in the [Tools] screen. Steps that display [Tools] are as follows. (These operations can only be performed by the System
Administrator.)
Steps
1
On the control panel of the multifunction device, press the <Log In/Out> button.
2
Use the <Numeric Keypad> button of the control panel or the software keyboard in the operating screen, and enter the device administrator User ID, and then press [Next] , and after this, enter your password and press [Enter].
(There are occasions when the password has not been set.)
17
2. Before Installing the Tool
3
In the operating screen, press [Tools].
4
Please confirm and set the relevant items in the [Tools] screen.
Verification of the External Access Kit
These steps can be performed for multifunction devices of the following models.
Note
• Some models may not be available in your country or region.
z
ApeosPort-IV C7780 / C6680 / C5580 z
ApeosPort-IV C5570 / C4470 / C3370 / C3371 / C2270 z
ApeosPort-IV C4430 z
ApeosPort-IV 5070 / 4070 / 3070 z
ApeosPort-IV 3065 / 3060 / 2060
18
2. Before Installing the Tool
0
Steps
1
Select [System Settings] in the [Tools] screen, and confirm whether [Web
Browser Setup] is displayed.
When display is made, the external access kit is available.
2
Press [Close].
Password Setting for Software Options
These steps can be performed for multifunction devices of the following models.
Note
• Some models may not be available in your country or region.
z z z z
ApeosPort-V C7780 / C6680 / C5580
(*6)
DocuCentre-V C7780 / C6680 / C5580
(*6)
ApeosPort-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373 / C2275
(*6)
DocuCentre-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373 / C2275
(*6) z z
ApeosPort-V C3320
DocuPrint CM415 AP z z
ApeosPort-IV C5575 / C4475 / C3375 / C3373 / C2275
DocuCentre-IV C5575 / C4475 / C3375 / C3373 z z
Color C70 / C60
Versant 80 Press z z
ApeosPort-V 7080 / 6080
DocuCentre-V 7080 / 6080 z z
ApeosPort-V 5070 / 4070
DocuCentre-V 5070 / 4070 z z
ApeosPort-V 4020
DocuPrint M465 AP z z
ApeosPort-IV 7080 / 6080
DocuCentre-IV 7080 / 6080
(*6) These include later models (T2).
19
2. Before Installing the Tool
In order to enable this function, it is necessary to set a password for the software options.
Passwords consist of 13 digits combining uppercase, lowercase, and symbol characters.
Model Name
DocuCentre-V C2265/C2263
ApeosPort-V 3065/3060/2060
DocuCentre-V 3065/3060/2060
Password
SBKPVNKELDHP@
QWTTHGMFWRPY@
ApeosPort-V C7776/C6676/C5576/C4476/C3376/C3374/
C2276
DocuCentre-V C7776/C6676/C5576/C4476/C3376/C3374/
C2276
IORPVRRBNMWG@
ApeosPort-V C7785/C6685/C5585
DocuCentre-V C7785/C6685/C5585
ApeosPort-V C7780 / C6680 / C5580
(*1)
DocuCentre-V C7780 / C6680 / C5580
(*1)
APJFGVMAJAUU@
NVJLHLNMCMFD@
UILCCWLJCLAE@
(*2)
ApeosPort-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373 /
C2275
(*1)
FHFXRCSPUKKS@
DocuCentre-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373
/ C2275
(*1)
UUOTKEEMSLSK@
(*2)
ApeosPort-V C3320
DocuPrint CM415 AP
QOJOOATVXURT@
AYGGEICOMHYP@
(*2)
HHEHJMXXZOUG@
SFHDLSXTWBTU@
(*2)
RRNBYJIMUEFF@ ApeosPort-IV C5575 / C4475 / C3375 / C3373 / C2275
DocuCentre-IV C5575 / C4475 / C3375 / C3373
Color C70 / C60
Versant 80 Press
ApeosPort-V 7080 / 6080
DocuCentre-V 7080 / 6080
ApeosPort-V 5070 / 4070
HPFMIOLPAJUT@
ZAXLLSWQTFHZ@
(*2)
OTPCJMSDBYIG@
IZRLOFMDOFIF@
(*2)
AFITTEEPWRER@
TMLUBRZBTIDW@
(*2)
DocuCentre-V 5070 / 4070
ApeosPort-V 4020
DocuPrint M465 AP
IVSBBTWBEHGP@
TSHXOQFEFAJR@
(*2)
CDVKZNBCEDAZ@
CLUGTTEPFCAE@
(*2)
UURJJHKKFFKP@
JTXRTPWDRUGO@
(*2)
ApeosPort-IV 7080 / 6080
DocuCentre-IV 7080 / 6080
DKEKFHZMBMSK@
(*1) These include later models (T2).
(*2) When you use the Single Sign On function, this password, as well as the ordinary password as above, is required.
20
0
2. Before Installing the Tool
Note
• When [System Settings] > [Web Browser Setup] in the [Tools] screen of your device is displayed, a software option password has already been set. Perform the steps for setting the SOAP port.
• The above table is as of September 2015. Applicable models and passwords are subject to change without notification. Contact one of our Customer Support Center to determine whether a password is necessary or when you don't know the password.
Steps
1
Select [Common Service Settings] > [Maintenance] from [System Settings].
2
Select [Software Options].
3
Use the keyboard to enter the password of your device.
4
Select [Reboot].
0
SOAP Port Setting
Steps
1
From [System Settings], select [Connectivity & Network Setup], then select
[SOAP] in [Port Settings], and press [Change Settings].
2
Set the following items.
z
[Port Status]: [Enabled] z
[Port Number]: [80]
3
Press [Close] until the message screen appears.
0
Protocol Setting
Steps
1
Select [Protocol Settings] in [Connectivity & Network Setup] under [System
Settings], and then set an IP address, subnet mask, and gateway address
(settings for the use in TCP/IP network environment).
Note
• Depending on the model, select [TCP/IP - Network Settings] in [Protocol Settings], and then make the applicable settings.
2
Select [IPv4-DNS Server Setup] or [IPv6-DNS Server Setup] in [Protocol
Settings] under [System Settings] > [Connectivity & Network Setup], and then select [Change Settings].
Note
• Depending on the model, select [TCP/IP - Network Settings] in [Protocol Settings], and then select either [IPv4-DNS Server Setup] or [IPv6-DNS Server Setup].
21
2. Before Installing the Tool
3
Select below value for each item.
z
[Get IP Address from DHCP]: [Disabled] z
[DNS Server IP Address]: your DNS server address
4
Select [Close] repeatedly until the [Tools] screen is displayed.
5
To exit [Tools], select [Close].
Proxy Server Setting
When connecting to the Internet from your multifunction device, carry out the following settings if utilizing an environment that connects via a proxy server.
Important
• In the network environment through the proxy server requiring authentication, you may not be able to use Scan Translation Service on Multifunction devices.
In this case, refer to the "Notes and restrictions"in following official site.
When you contracted for a Scan Translation Service in Japan
http://www.fujixerox.co.jp/support/service/notes/index.html
When you contracted for a Scan Translation Service in other countries outside of Japan
www.fxap.com.sg/product/software/scanservice/index.jsp
0
Steps
1
In [System Settings] > [Connectivity & Network Setup] > [Proxy Server
Settings], configure the settings for using the device in an HTTPS environment, such as server name and port number.
2
Select [Addresses to Bypass Proxy Server] in [System Settings] > [Connectivity
& Network Setup] > [Proxy Server Settings] and press [Edit...].
3
Enter "localhost" and press [Select].
Note
• If there is already an address present, append a semicolon (;) to the end of it, and then add "localhost".
4
Press [Close] until the message screen appears.
22
0
2. Before Installing the Tool
Web Browser Setting
Steps
1
Select [Web Applications Version] in [System Settings] > [Web Browser Setup] and press [Edit...].
Note
• When the external access kit option is not available for your multifunction device, which includes the following models, [Web Browser Setup] will not be displayed.
However, some models may not be available in your country or region.
ApeosPort-IV C7780 / C6680 / C5580
ApeosPort-IV C5570 / C4470 / C3370 / C3371 / C2270
ApeosPort-IV C4430
ApeosPort-IV 5070 / 4070 / 3070
ApeosPort-IV 2060 / 3060 / 3065
• When [Web Browser Setup] is not displayed for a multifunction device included in the following models, a software option password needs to be set. For more information, refer
to "Password Setting for Software Options" (P.19)
However, some models may not be available in your country or region.
ApeosPort-V C7780 / C6680 / C5580
(*7)
DocuCentre-V C7780 / C6680 / C5580
(*7)
ApeosPort-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373 / C2275
(*7)
DocuCentre-V C7775 / C6675 / C5575 / C4475 / C3375 / C3373 / C2275
(*7)
ApeosPort-V C3320
DocuPrint CM415 AP
ApeosPort-IV C5575 / C4475 / C3375 / C3373 / C2275
DocuCentre-IV C5575 / C4475 / C3375 / C3373
Color C70 / C60
Versant 80 Press
ApeosPort-V 7080 / 6080
DocuCentre-V 7080 / 6080
ApeosPort-V 5070 / 4070
DocuCentre-V 5070 / 4070
ApeosPort-V 4020
DocuPrint M465 AP
ApeosPort-IV 7080 / 6080
DocuCentre-IV 7080 / 6080
2
Select "Enable File Printing", and press [Change Settings].
3
Set the following item.
z
Enable File Printing: [Yes]
4
Select "Accept Cookies", and press [Change Settings].
5
Set the following item.
z
Accept Cookies: [Yes] or [Warn user when cookie is offered]
6
Select "Use TLS1.0", and press [Change Settings].
7
Set the following item.
z
Use TLS1.0: [Yes]
(*7) These include later models (T2).
23
2. Before Installing the Tool
8
Press [Close] until the menu screen appears.
Note
• Depending on the type of setting, it might be necessary to restart your multifunction device. Restart your device if a restart screen appears.
0
Plug-in Settings
When using the Single Sign On function, you need to validate a plug-in setting.
If a plug-in setting is not validated, execute the following procedure.
Steps
1
Select [Embedded Plug-ins] in [System Settings] > [Common Service Settings]
> [Plug-in Settings], then press [Change Settings].
Note
• When [Plug-in Settings] is not displayed, you need to set a password for software option.
For more details, please refer to the "Password Setting for Software Options" (P.19).
2
Select [Enabled], then press [Select].
3
Press [Close].
4
Press [Close].
Note
• When a screen instructed to reboot is displayed, you need to reboot.
24
2. Before Installing the Tool
Multifunction Device Environment Settings from a PC
0
Important
• When using the Multifunction Device Linkage Tool preinstalled on your multifunction
device, this step and following steps are not required. Please refer to "Confirmation of
Installation Result" (P.33) to confirm that the function is operating properly.
Before installing, use CentreWare Internet Services to make the following settings.
z
SSL/TLS Settings
During installation (or uninstallation), the Multifunction Device Linkage Tool uses the
SSL/TLS protocol for HTTP communications between the multifunction device you are using and a computer on the network.Enable SSL/TLS communication if it is not enabled.
Steps
1
Open a Web browser in your network connected computer.
2
Enter the IP address of the multifunction device for which tool is installed in the address input box of the Web browser, and then press the <Enter> key.
CentreWare Internet Services will be started.
Note
• At the time of connecting to CentreWare Internet Services or when a username and password request screen appears during operation, enter the device administrator User
ID and password, and then click [OK].
3
Click [Create New Self Signed Certificate] in the [Properties] tab > [Security] >
[Machine Digital Certificate Management].
Note
• XPS stands for XML Paper Specification.
25
2. Before Installing the Tool
4
Click [Apply].
5
Reload the Web browser.
26
2. Before Installing the Tool
6
Check [Enabled] for [HTTP - SSL / TLS Communication] in [Properties] >
[Security] > [SSL / TLS Settings].
7
Click [Apply].
8
If a message is displayed indicating that the multifunction device should be restarted, click [Reboot Machine].
9
Click [OK] in the confirmation screen.
When restarting the device, communication will be temporarily disconnected, so please wait for a little while, and then reload the Web browser and make reconnection to the multifunction device.
27
2. Before Installing the Tool
28
3. Installation Process
3. Installation Process
This section describes the procedures for installing the Multifunction Device Linkage Tool into the multifunction device.
Install the Multifunction Device Linkage Tool into the multifunction device.
There is a Multifunction Device Linkage Tool that supports the Single Sign On function and one that does not. Install one or the other according to your requirements.
See "Confirmation of Installation Result" (P.33) and confirm that the function is operating
properly after installation, or when using the Multifunction Device Linkage Tool preinstalled on your multifunction device.
Note
• If you will use the Single Sign On function on a model in which the Multifunction Device
Linkage Tool has been pre-installed, you must reinstall the Multifunction Device Linkage
Tool that supports the Single Sign On function.
Furthermore, please refer to the following link on our official company website when downloading the Multifunction Device Linkage Tool.
z
For users who concluded a Scan Translation contract in Japan
http://www.fujixerox.co.jp/solution/scantrans/ z
For users who concluded a Scan Translation contract in a country other than Japan http://www.fxap.com.sg/product/software/scanservice/index.jsp
Install
Installation will be done from a PC to the multifunction device.
Note
• Install the tool when the multifunction device is not being operated or executing a job.
The installation cannot be done when the multifunction device is being operated or executing a job.
• The control panel of the multifunction device cannot be used when installing the
Multifunction Device Linkage Tool.
0
The installation steps are as follows.
Steps
1
Use your PC to download the Multifunction Device Linkage Tool from our official website.
2
Unzip the downloaded compressed file (.zip), and double click the exe file contained in the folder.
29
3. Installation Process
Note
• If a [Security Warning] screen is displayed, click [Start] and continue the installation.
3
Click [Next].
4
Enter the IP address of the multifunction device, and click [Next].
Note
• Enter the IPv4 IP address.
Example: 192.0.2.1
30
3. Installation Process
5
Enter the username and password of the System Administrator, and click
[Next].If you are reinstalling the Multifunction Device Linkage Tool on a model which came with the Tool pre-installed, continue to Step 6.Otherwise, continue to Step 7.
6
Select [Reinstall], and then click [Next].
7
Click [Next].
31
3. Installation Process
8
Click [Completed].
Note
• It may take a few minutes until the completion screen is displayed.
• When installing the function in additional multifunction devices, check [Install on another device] and then click [Completed], thereafter repeating steps 3 - 7.
9
Restart the multifunction device.
10
Uncheck [Enabled] for [HTTP - SSL / TLS Communication] in CentreWare
Internet Services, thereby returning the state to disabled.
Note
• Please refer to "Multifunction Device Environment Settings from a PC" (P.25)regarding
how to make settings.
32
0
3. Installation Process
Confirmation of Installation Result
The procedure for confirming the installation results is as follows.
Steps
1
Press the <Services Home> button on the control panel of the multifunction device.
2
Press [Scan Translation] on the menu screen.
Note
• The display may differ depending on the model of your multifunction device or the setting of the display language.
Note
• If the [Scan Translation] button is not displayed, confirm that the necessary environment
settings have been correctly set in the multifunction device. Refer to "Multifunction Device
Environment Settings" (P.16)regarding environment settings.
• When using another custom service or when changing the function button settings displayed in the Services Home screen, the [Scan Translation] button may not appear. If this is the case, change the settings for [Services Home] in [System Settings] > [Common
Service Settings] > [Screen / Button Settings…]. For more information, refer to the
"Administrator Guide" of the multifunction device.
• If the verification method of the device is [Login to Local Accounts] or [Login to Remote
Accounts], please enter verification mode, and then press the button.
• When an "Unable to access the service. Check the network settings and status." error message is displayed, please confirm the following.
Confirmation of proxy server settings
Item Confirmation Details
"Multifunction Device Environment Settings" (P.16)Confirm
that the settings made for "server name", "port name", "login name", and "password" have been carried out correctly.
Confirmation of the restriction settings of the proxy server
Make sure that the settings of the multifunction device allow connection to the Internet from the IP address for the proxy server administrator.
Confirmation of PC connection Using your network connected computer, open a Web browser and confirm that you can connect to the following
URL.
https://scantranslation.fujixerox.com/
33
3. Installation Process
Installation has completed if the Scan Translation Service Login screen appears.
Note
• If the log-in screen is not displayed, please confirm that the necessary environment
settings have been correctly set in the multifunction device. Please refer to "Multifunction
Device Environment Settings" (P.16)regarding environment settings.
• Once you log in, the [Select from History List] button will be displayed the next and subsequent times you log in.
z
When the Single Sign On function is supported:
Note
• If you are the system administrator, the [Admin Menu] button is displayed.
z
When the Single Sign On function is not supported:
34
Single Sign On Function Settings
If you have installed the Multifunction Device Linkage Tool that supports the Single Sign
On function, you can specify whether to remember each user's user ID and password entered on the login screen.
If you choose to remember user IDs and passwords, authenticating using the multifunction device allows you to configure it so that you do not have to enter user IDs when logging in to Scan Translation Service, or to automatically log in without the login screen being displayed.
3. Installation Process
Note
• You may not be able to use the Single Sign On function, depending on your multifunction
device.For more information, see "Single Sign On Function" (P.12).
• If you will use the Single Sign On function, you must have registered an authenticated user using the authentication function on the multifunction device.For more information, refer to the "Administrator Guide" provided with your multifunction device package.
• To use the Single Sign On function, you must configure the environment settings for the
multifunction device.For more information, see "Multifunction Device Environment
• For information on how to use the Single Sign On function for each user, refer to the "Scan
Translation Service User Guide".
When using the Single Sign On function, the administrator can make the following settings.
0
[Admin Menu] Screen Display
To make administrator settings, perform the following steps on the multifunction device.
Steps
1
On the control panel of the multifunction device, press the <Log In/Out> button.
2
Use the <Numeric Keypad> button or the displayed keyboard to enter the device administrator User ID, and then press [Enter].
3
Press [Scan Translation Service] or [Scan Translation] on the menu screen.
Note
• The display may differ depending on the model of your multifunction device or the display language setting.
35
3. Installation Process
4
Press [Admin Menu] on the [Log In] screen.
The [Admin Menu] screen is displayed.From this screen, configure whether the
[Remember] check box is displayed, and clear stored authentication information.To return to the Log In screen, press [Back].
36
0
[Remember] Check Box Settings
Configure whether to display the [Remember] check box on the Scan Translation Service
[Log In] screen.If users select the [Remember] check box, they can use the Single Sign On function.
Steps
1
Select [Yes] or [No] for [Remember Authentication Information] on the [Admin
Menu] screen.
If you select [Yes], the [Remember] check box will be displayed on the Scan Translation
Service login screen.
If you select [No], that [Remember] check box will not be displayed.
2
Press [Apply].
If this setting has been switched from [Yes] to [No], perform steps 3 and 4.
3
Press [Yes] on the [Change Value] screen.
0
3. Installation Process
4
Select whether to clear the stored user authentication information on the
[Clear Authentication Information] screen.Press [Yes] to clear all currently stored authentication information. Press [No] to retain it.
Note
• If you select [No] and then change [Remember Authentication Information] to [Yes] later, you can use the stored information again.
Deleting of Stored Authentication Information
To delete all stored user authentication information, perform the following steps.
Note
• If you perform these steps, users will need to enter their User IDs and Passwords when accessing Scan Translation Service until they select [Remember] again.
Steps
1
Press [Delete] in [Clear Authentication Information] on the [Admin Menu] screen.
2
Press [Yes] on the [Clear Authentication Information] screen.
37
3. Installation Process
Uninstall/Version Upgrade
0
The following procedure is for uninstalling the Multifunction Device Linkage Tool or upgrading to a newer version.
Steps
1
On your PC, double click the exe file of the Multifunction Device Linkage Tool.
2
Click [Next].
3
Enter the IP address of the multifunction device undergoing the function uninstall or version upgrade, and then click [Next].
Note
• Enter the IPv4 IP address.
Example: 192.0.2.1
38
3. Installation Process
4
Enter the username and password of the System Administrator, and click
[Next].
5
Select [Remove] for uninstallation or select [Reinstall] for version upgrade, and then click [Next].
Note
• Click [About] to confirm the version of the tool to link the multifunction device.
Furthermore, the version of the tool to link the multifunction device will be different from the version of Scan Translation Service.
6
After the confirmation screen is displayed, click [Next].
7
After the install completion screen is displayed, click [Completed].
8
Restart the multifunction device.
39
3. Installation Process
40
Index
C
Confirmation of Each Item................................................ 17
Confirmation of Installation Result................................ 33
E
Environment Settings........................................................... 16
I
Install.......................................................................................... 29
M
Multifunction Device Advanced Verification.............. 14
Multifunction Device Environment Settings from a PC25
O
Overview .......................................................................................9
P
Password Setting for Software Options........................ 19
Plug-in Settings....................................................................... 24
Protocol Setting ...................................................................... 21
Proxy Server Setting.............................................................. 22
S
Setting Method....................................................................... 17
SOAP Port Setting .................................................................. 21
U
Uninstall..................................................................................... 38
V
Verification of the External Access Kit .......................... 18
Version Upgrade .................................................................... 38
W
Web Browser Setting ............................................................ 23
41
Scan Translation Service Multifunction Device Linkage Setup Guide
Fuji Xerox Co., Ltd.
ME7647E2-2 (Edition 1)
September 2015
Copyright
©
2015 by Fuji Xerox Co., Ltd.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project