VIVOTEK VT-AM214 Datasheet

PDF

Document

VIVOTEK Fixed Dome & PTZ Series

Wall-mount Bracket

User’s Manual

Using AM-214 wall-mount bracket and compatible accessories

Rev. 1.1

IP Surveillance

AM-214 Wall-mount Bracket

I Compatible VIVOTEK Cameras

Fixed Dome series

PTZ series

FD8133, FD8134, FD8133V, FD8134V, FD8161, FD7132,

FD7131, FD8162, FD8135H, FD8362E, FD8362, FD8372,

FD8335H, FD8361, FD8361L, FD8131

PZ7111, PZ7112, PZ7121, PZ7122, PZ7131, PZ7132,

PZ7151, PZ7152, PZ81x1W, PZ81x1

You may also refer to VIVOTEK's website for the list of supported models. Support for other models can be available through time.

II Accessories

Adaptor ring for FD8162

III Installation

Mounting Hole Definitions

Above are the locations of different groups of mounting holes for matching different cameras:

Hole Type Applicable Cameras

FD8161 / FD7132 / FD7131

FD8162 / FD8135H

FD8133V / FD8134V

FD8133 / FD8134 / FD8131

Screw No. of screws

M4X15

M4X8XD6 3

M3X6 2

PZ7132 / PZ7151 / PZ7152 / PZ81x1W / PZ81x1

FD8335H / FD8361 / FD8361L / FD8362 / FD8362E /

FD8372

FD8361 (cables routed to the side of the bracket)

M3X4

M4X15

For cabling and configuration details with each network camera, please refer to their documentation.

Refer to the table below for the description of the included screws:

Screw Description

M4X15 Phillips pan head

Quantity Applies to

4 A holes

2 M3X4 Phillips pan head

(black)

M4X8XD6 Phillips pan head

M4X25XD9 Phillips pan head

D holes for PZ and PT series

B holes

Securing the bracket to wall

M3x6 Phillips pan head 2 C holes

Plastic anchors 4 Securing the bracket to wall

NOTE:

1. It is presumed that this wall-mount bracket is installed with a hole drilled on the wall for routing power lines, DI/DO, and Ethernet cables.

2. Route cables before you secure the wall-mount bracket to a wall.

3. For details on the cable connections with each camera, please refer to their Quick

Installation Guide.

Wall Mount Installation - FD8134V

Below is a general, sample procedure using a wall mount bracket:

1. Locate the position where you want to install the wall mount bracket and camera. Drill holes on the wall for securing the bracket and for routing the cables.

2. Secure the bracket by hammering anchors into the wall and then fasten screws through the four mounting holes on the bracket.

3. Route power lines and other cables through the wall and the bracket.

4. Align the camera's mounting holes with the B holes. Secure the camera to the wall mount bracket as shown below.

M4X8XD6 Screws

Aligned with B holes

Route cables through here

IMPORTANT!

The screws and mounting surface must be able to support a weight of 4 kg.

5. Proceed with initial setup such as enabling network access, focus tuning, or zooming.

When done, secure the outer dome cover.

NOTE:

Use the correct type of screws when installing cameras to the mounting cap. Refer to page 3 for the screw type.

Wall Mount Installation - FD8134

Below is a sample procedure using wall mount bracket and an FD8134:

1. Determine a hard surface wall location, and use the four mounting holes on the wall mount bracket to mark the positions where holes will be drilled to secure the bracket.

M3X6 Screws

2. Drill holes on the wall for passing cables and for securing the wall mount bracket.

3. Secure the bracket by hammering anchors into the wall and then fasten screws.

4. Route power lines and other cables through the bracket and wall.

5. Secure camera to the wall mount bracket using the C holes and M3x6 screws.

6. Proceed with initial setup such as enabling network access, focus tuning, or zooming.

When done, secure the outer dome cover.

Wall Mount Installation - FD8162

Below is a sample procedure using wall mount bracket and an FD8162:

1. Determine a hard surface wall location, and use the four mounting holes on the bracket to mark the positions where holes will be drilled to secure the bracket.

A* holes

M4X15

Camera Lens Orientation

2. Drill holes on the wall for securing the bracket and for routing cables.

3. Route cables through the wall and bracket.

4. Secure the wall mount bracket to the wall using the included screws and plastic anchors.

5. Rotate the adaptor ring to match the camera lens orientation your prefer, e.g., to the front or to the left. Secure the adaptor ring to bracket using the M4X15 screws to the A2 and A4 holes on the bracket.

6. Secure the camera to the adaptor ring using the included screws.

7. Connect power lines and cables to the camera.

8. Proceed with initial setup such as enabling network access, focus tuning, or zooming.

When done, secure the outer dome cover.

Wall Mount Installation - PZ7151 (and Applies to All PZ Series)

Below is a general, sample procedure for installing a PZ pr PT series camera with the wall mount bracket:

1. Detach the mount panel by loosening 5 screws from the wall mount bracket.

Wall mount bracket

2. Secure the camera from the inner side of the mount panel by driving M3 screws to the bottom of camera.

3. Locate the position where you want to install the wall mount bracket. Drill holes on the wall for securing the bracket and for routing cables.

4. Route power lines and other cables through the wall and the bracket.

5. Secure the wall mount bracket to the wall using the included fasteners and screws.

6. Attach the camera and the mount panel to the wall mount bracket using the 5 screws you previously removed.

7. Connect power lines and cables, and you may now begin the initial connection and configuration.

M3X4

NOTE:

Use the correct type of screws when installing cameras to the mounting cap. Refer to page 3 for the screw type.

Wall Mount Installation - FD8161

Below is a general, sample procedure using a wall mount bracket with the FD8161 camera:

1. Locate the position where you want to install the wall mount bracket and camera. Drill holes on the wall for securing the bracket and for routing cables.

2. You can route cables through the hole in the center of the bracket and the space beneath the camera.

3. Secure the wall mount bracket to the wall using the included plastic anchors and screws.

A* holes

Cable routing path

4. Attach the camera to the bracket using 2 M4X15 screws.

5. Connect cables and you may now begin the initial connection and configuration.

6. Attach dome cover to the camera.

Wall Mount Installation - FD8362E / 8335H / 8372

Below is a general, sample procedure using a wall mount bracket with the FD8362E,

FD8335H, and FD8372 cameras:

1. Locate the position where you want to install the wall mount bracket and camera. Drill holes on the wall for securing the bracket and for routing cables.

2. You can route cables through the hole in the center of the bracket.

3. Secure the wall mount bracket to the wall using the included plastic anchors and screws.

4. Attach the camera's mounting plate (which comes with the outdoor series cameras) to the bracket using 4 M4X15 screws.

5. Connect cables and you may now begin the initial connection and configuration.

IMPORTANT!

The screws and mounting surface must be able to support a weight of 5 kg.

This page is intentionally left blank.

Hello! I am an AI chatbot specifically trained to assist you with the Vivotek 909001900G Data Sheet. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!