Priyankoo Sarmah Assistant Professor Indian Institute

Priyankoo Sarmah Assistant Professor Indian Institute
Priyankoo Sarmah
Assistant Professor
Phone Nos. :+91-361-258 -2574
+91-361-258 -2594
Indian Institute of Technology,
Guwahati,
Guwahati-781 039, Assam, India.
Fax
Email
:+91-361-258-2089
+91-361-258-2599
: [email protected]
Date : 24/01/2014
R&D/07/HSS/P/PRS/02/2013-14
NOTICE INVITING QUOTATION FOR SUPPLY & INSTALLATION OF LAPTOP COMPUTER,ALL IN ONE
DESKTOP COMPUTER,DYNAMIC CLOSE TALK HEAD WORN MICROPHONE,HEADPHONE,SOUND
MIXER,DYNAMIC DOUBLE RIBBON MICROPHONE AND PORTABLE DIGITAL RECORDER FOR THE
DEPARTMENT OF HUMANITIES AND SOCIAL SCIENCES (PROJECT NO.HSS/P/PRS/02), IIT GUWAHATI.
Quotations for supply of equipments as per details at ANNEXURE-I,II,III,IV,V,VI,VII - in single bid as
indicated in the CHECKLIST given below, in sealed covers, are hereby invited so as to reach the undersigned on or
before 19 FEBRUARY, 2014.
INSTRUCTION TO BIDDERS:
Single Bids:
(a) In case of single bid quotations will have to be submitted in single bid, in a properly sealed cover; and the
address of the firm submitting the quotation and the Officer to whom the quotation is addressed, must appear
distinctly on the sealed cover, Further, on the sealed cover the following are to be written: ‘QUOTATION FOR
SUPPLY & INSTALLATION OF LAPTOP COMPUTER, ALL IN ONE DESKTOP COMPUTER, DYNAMIC CLOSE
TALK HEAD WORN MICROPHONE, HEADPHONE, SOUND MIXER, DYNAMIC DOUBLE RIBBON
MICROPHONE AND PORTABLE DIGITAL RECORDER IIT
GUWAHATI’.
VIDE
NIQ
NO.
R&D/07/HSS/P/PRS/02/2013-14, LAST DATE FOR SUBMISSION 19 FEBRUARY, 2014.
NOTE:
The bid documents are not transferable and the firm’s seal and signature of the authorized
official must appear on all the papers and envelopes submitted.
(b)The bid must mention the prices of all items asked for individually and then summed up at last i.e. basic price
and other charges such as Packing, Freight, insurance ,Installation & commissioning charge, VAT/Tax etc as
applicable;
(c) Annual Maintenance Contract (AMC) rate (after expiry of warranty period) is to be clearly indicated –
preferably in both comprehensive and non-comprehensive terms, failure to which the offer may not be
considered even if it turns out to be at the lowest price.
(d) Details of the technical features of the offered equipment along with Standard Technical literature on each of
the items offered;
(e) Dealership certificate on the offered products in case of dealer/s;
(d) List of reputed organizations/Institutions, where similar orders have been executed
(copies of the purchase/work orders will have to be enclosed);
(e) Up-to-date Sales Tax clearance certificate (for vendors outside the State of Assam)/VAT Registration
Certificate indicating also the TIN number (for vendors from within the State of Assam) OF THE FIRM will have
to accompany the quotation to be submitted;
(f) Details of nature and maximum period of warranty offered by the vendor
(g) After Sales Service: The name & address of the nearest available authorized service centre to IIT, North
Guwahati, should be stated in the quotation.
TERMS & CONDITIONS:
(Please note the term ‘both foreign & indigenous’ wherever mentioned means the term is applicable to
both foreign & indigenous purchase)
01. Rates :Rates quoted for indigenous items should be on FOR IIT Guwahati, on DOOR DELIVERY basis, with
break-ups as per details below (For import items please refer ‘Additional Terms for imported goods’ at clause
No. 25 below).
Break-ups of cost
(a) Basic Price
(b) (+) Central Excise Duty, if any
(c) (+) VAT/ Central Sales Tax ( On Sub-Total Price, including Excise Duty, if any)
(d) (+) Freight & Insurance Charge, if any
(e) (+) Installation & Commissioning Charge, if any
(f ) Grand Total F.O.R. IIT Guwahati, Price
Note: Vague terms like “packing, forwarding, transportation etc. extra” without mentioning the specific amount
will not be accepted. Such offers shall be treated as incomplete and rejected. Bidders shall indicate their rates
in clear/visible figures as well as in words and shall not alter/overwrite/make cutting in the quotation. In case of
a mismatch, the rates written in words will prevail.
02. Validity (Both foreign & indigenous) : Quoted rates must be valid for 120 days.
03. Performance Bank Guarantee(Both foreign & indigenous) : Performance Bank Guarantee(Both foreign &
indigenous) : The successful bidder shall furnish an unconditional Performance Bank Guarantee valid till 60
days after the warranty period from a scheduled Bank for 10% of the Purchase Order value within 21 days of
placement of order failing which the contract shall be deemed as terminated (APPLICABLE ONLY TO
ORDERS COSTING MORE THAN INR 5,00,000.00).That
(a)The Vendor shall provide a Certificate of Guarantee guaranteeing LAPTOP COMPUTER, ALL IN ONE
DESKTOP COMPUTER, DYNAMIC CLOSE TALK HEAD WORN MICROPHONE, HEADPHONE, SOUND
MIXER, DYNAMIC DOUBLE RIBBON MICROPHONE AND PORTABLE DIGITAL RECORDER of the
satisfactory operation of the components and against poor workmanship, bad quality of materials used, faulty
designs and performance figures given by the Vendor.
(b)This guarantee shall be operative for a period of 60 days after the warranty period. The performance
guarantee would be to the extent of 10 % of the order value.
(c)The Vendor shall at his own cost rectify the defects/replace the items supplied, for defects identified during
the period of guarantee
(d)While clauses 3(a),3(b) and 3(c) are applicable to all orders worth Rs.5 Lakhs or more, competent authority
may take appropriate decisions on exceptional cases.
04. PENALTY FOR DELAYED DELIVERY (for both foreign & indigenous):
In the event of delayed delivery, installation & commissioning i.e. after the expiry of the period as agreed by
both the parties, the vendor shall be liable for a penalty deduction at a percentage of the value of the
undelivered equipment subject to a maximum of 10% (ten percent) as detailed below:
@ 1% up to one week;
@ 2.5% up to two weeks;
@ 5% up to three weeks;
@ 10% for four weeks and above
For the purpose of this clause, part of the week is considered as a full week.
05. In case of indigenous supplies, the goods should be insured against theft, loss or breakage during transit and
insurance charges should not exceed 1% of the cost of material supplied, the rates of Sales Tax, Excise Duty
etc. (as applicable) should be clearly indicated. Form C & D is not applicable to us. However, we are exempted
from payment of Excise Duty and certificate to this effect can be provided.
06. Penalty for delayed supply(Both foreign & indigenous) :In case of supply order for the SCIENTIFIC
EQUIPMENTS/ APPARATUS, the date of delivery should be strictly adhered to otherwise the Director, IITG
reserves the right not to accept delivery in part or full and claim liquidated damages of 1% per week subject to
maximum of 10% of the total value of supply
07. Pre-installation requisites(Both foreign & indigenous) : Pre-installation requisites (electrical/floor/space/airconditioning etc.) if any should invariably be mentioned clearly. Installation/ Training will be the full responsibility
of the supplier/ Indian Agent.
08. Short Shipment(Both foreign & indigenous) :If any short-shipment etc. is noticed, the same will be arranged
immediately with all charges to this effect to be born by supplier/Indian agent.
09 Genuine Pricing (Both foreign & indigenous) :Vendor is to ensure that quoted price is not more than the price
offered to any other customer in India to whom this particular item has been sold, particularly to IIT/Institutes
and other Government Organization. Copy of the latest price list for the quoted item, applicable in India, must be
enclosed with your offer.
10. Excise Duty:The Institute is exempted from payment of Central Excise Duty vide GOI Notification No.
10/97-Central Excise, dated 01.03.97 with Regn.No. TU/V/RG-CDE(351)/2011, DATED 19.09.2011.
11. VAT:For a vendor within the State of Assam, appropriate VAT (to be deducted at source) will be applicable. For
exemption from Octroi, wherever required, the Institute will issue necessary certificates.
12. Entry Tax :Assam Govt. Entry Tax – usually @4% [to be paid by IIT Guwahati, not by the vendor], wherever
applicable, will be added while evaluating cost status of the concerned equipment to be supplied by vendors
from outside the State of Assam.
13. Delivery : (a)Delivery of goods at IIT Guwahati, will have to be maximum within 45(Forty-five) days from the
date of issue of the Purchase Order.
(b)Safe delivery of goods: All aspects of safe delivery shall be the exclusive responsibility of the vendor. At the
destination site, the cartons will be opened only in the presence of IIT user/representative and vendor's
representative and the intact position of the seal for not being tempered with, shall form the basis for certifying
the receipt in good condition.
(c) No Part Delivery : part shipment will not be allowed.
14. Mode of Payment for Indigenous Purchase(For import items please refer „Additional Terms for imported
goods‟ clause No.28 below) :
(1)Payment for Indigenous Purchases will be maximum within 45 days from the date of successful delivery and
installation of goods at IIT Guwahati, North-Guwahati, generally through A/c payee cheque. In case payment is
to be made by DD, the Draft commission will be deducted from the bill amount. or
(2) Payment through bank against proof of dispatch: 90% payment shall be released on receipt of proof of
dispatch through State Bank of India, IIT Guwahati Branch, Guwahati, Assam. Balance 10% shall be released
after installation /handing over of the equipment to the consignee(s).
Note: Please note as per Institute‟s norm advance payment is not allowed for indigenous purchase.
15. Quotation by Fax/Mail not Acceptable(Both foreign & indigenous) :The offers submitted by telex/ telegram/
fax/ E-mail etc. shall not be considered. No correspondence will be entertained on this matter.
16. Late and delayed tender(Both foreign & indigenous) :Late and delayed tender will not be considered. In
case any unscheduled holiday occurs on prescribed closing/opening date the next working day shall be the
prescribed date of closing/opening.
17. Conditional tenders not acceptable(Both foreign & indigenous) : Conditional tenders shall not be accepted
on any ground and shall be rejected straightway. In other word, printed conditions mentioned in the tender bids
submitted by vendors will not be binding on IITG. All the terms and conditions for the supply, payment terms,
penalty etc. will be as those mentioned herein and no change in the terms and conditions by the vendors will be
acceptable.
18. Specifications are basic essence of the product (Both foreign & indigenous) : It must be ensured that the
offers are strictly as per our specifications. At the same time it must also be kept in mind that merely copying
our specifications in their quotation shall not make firms eligible for consideration. A quotation has to be
supported with the printed technical leaflet/literature (wherever applicable) and the specifications mentioned in
the quotation must be reflected/ supported by such printed technical leaflet/literature model quoted/tendered
specifications should invariably be highlighted in the leaflet/literature for easy reference.
19. Enquiry during the course of evaluation not allowed(Both foreign & indigenous) : No enquiry shall be made
by the bidder(s) during the course of evaluation of the tender till final decision is conveyed to the successful
bidder(s). However, the Committee/its authorized representative and office of IIT GUWAHATI can make any
enquiry/seek clarification from the bidders. In such a situation, the agency shall extend full co-operation. The
bidders can also be asked to arrange demo. of the offered items, in a short period notice, as such the bidders
have to be ready for the same.
20. The acceptance of the quotation(Both foreign & indigenous) will rest solely with the Director, IITG, who in the
interest of the Institute is not bound to accept the lowest quotation and reserves the right to himself to reject or
partially accept any or all the quotations received without assigning any reasons.
21. Force Majeure(Both foreign & indigenous) : (a) If the performance of the obligation of either party is rendered
commercially impossible by any of the events hereafter mentioned that party shall be under no obligation to
perform the agreement under order after giving notice of 15 days from the date of such an event in writing to the
other party, and the events referred to are as follows: I) any law, statute or ordinance, order action or regulations
of the Government of India. II) Any kind of natural disaster and III)Strikes acts of the Public enemy, war,
insurrections, riots, lockouts, sabotage.
22. Termination for default(Both foreign & indigenous) : Default is said to have occurred
If the supplier fails to deliver any or all of the services within the time period(s) specified in the purchase
order or any extension thereof granted by IIT.
If the supplier fails to perform any other obligation(s) under the contract
If the vendor, in either of the above circumstances, does not take remedial steps within a period of 30 days after
receipt of the default notice from IIT (or takes longer period in-spite of what IIT may authorize in writing), IIT may
terminate the contract / purchase order in whole or in part and forfeit the EMD/PBG as applicable. In addition to
above, IIT may at its discretion also take the following actions: IIT may procure, upon such terms and in such
manner, as it deems appropriate, goods similar to the undelivered items/products and the defaulting supplier
shall be liable to compensate IIT for any extra expenditure involved towards goods and services obtained.
23. Applicable Law(Both foreign & indigenous) :
(a)The contract shall be governed by the laws and procedures established by Govt. of India and subject to
exclusive jurisdiction of Competent Court and Forum in Guwahati, India only.
(c). Any dispute arising out of this purchase shall be referred to the Director IIT Guwahati, and if either of the
parties hereto is dissatisfied with the decision, the dispute shall be referred to the decision of an Arbitrator, who
should be acceptable to both the parties, to be appointed by the Director of the Institute. The decision of such
Arbitrator shall be final and binding on both the parties.
ADDITIONAL TERMS FOR IMPORTED GOODS
Following terms besides the fore mentioned terms will be applicable in case of foreign purchases :
24. Rates :Quoted rates should be in CIF/CIP Kolkata terms and charges to be stated in the following break-ups (a) Ex-works value
(b) + Documentation & Handling Charge, if any
(c) + Estimated Overseas Freight to be paid at actual against authentic documents and monetary receipt
(d) + Estimated Overseas Insurance Charge to be paid at actual against authentic documents and monetary
receipt (In case the firm holds open insurance policy, the Insurance Certificate relating to the consignment will
have to be provided).
(e) Total CIP/CIF Kolkata value
25. After Sales Service: In case of imported stores, foreign manufacturing firms should indicate facilities available
for after sales service in India
without which their offers are liable to be ignored.
26. Delivery :
(a)Delivery of goods at IIT Guwahati, will have to be maximum within 95(ninety-five) days from the date of issue
of the Purchase Order.
(b)Delivery at kolkata Airport only: As we do not have clearing agent in any other Airport/Seaport, delivery is to
be made only at Kolkata .
(c)While transshipment will be allowed, part shipment will not be allowed.
27. Payment
:
(a).Above $10,000.00: By an irrevocable letter of Credit at CIF/CIP Kolkata value negotiable through any
overseas branch of Axis Bank Ltd with unrestricted provision.
(b)Below $10,000.00 by FDD/Wire Transfer as given below:
(i) Advance payment Against Bank Guarantee: 90% of the price will be paid in advance against equivalent
bank guarantee from a scheduled bank provided by the supplier/Indian Agent. The remaining 10% shall be
released only after receipt and acceptance of materials in good condition or after satisfactory installation and
commissioning of the equipment.
or
(ii) Payment Against Proof of Despatch: 90% of the price will be paid against receipt of proof of dispatch such
as AWB, Invoice, Packing List, Insurance certificate, etc.. The remaining 10% shall be released only after
receipt and acceptance of materials in good condition or after satisfactory installation and commissioning of the
equipment.
or
(iii) 100% Payment Basis: On request by the supplier/s 100% payment by FDD will be made. In this case on
receipt of your Order Acknowledgement an FDD will be established for total ordered value, thereupon, a Xerox
copy of the FDD will be sent to you which will enable you to send the materials. On satisfactory receipt and
acceptance of the materials or satisfactory installation and commission of the equipment the Original FDD will
be sent to you.
Note:Please note FDD/LoC will not be opened unless and until Letter of Acknowledgement in original is
received at IIT Guwahati, directly from the principal (Even in case of firms having subsidiary office in India). The
Indian agents are therefore advised to submit quotation after consultation with their respective principals).
28. Customs Duty :The Institute is generally exempted from payment of Customs Duty vide GOI Notification
No.51/96-Customs, dated 23.07.96, with Regn. No. TU/V/RG-CDE(351)/2011, DATED 19.09.2011. [CUSTOMS
DUTY EXEMPTION CERTIFICATE WILL BE MADE AVAILABLE BY THE INSTITUTE IN REGARD TO
QUOTES IN FOREIGN CURRENCY ONLY [ NOT AGAINST QUOTES MADE BY A FIRM IN INDIAN
CURRENCY, UNLESS THE CONCERNED FIRM IS A FOREIGN HOLDING COMPANY WITH `FDI’
CERTIFICATE ISSUED BY THE MINISTRY OF FINANCE, GOVT. OF INDIA ].
29. Agency Commission: The percentage of ex-works value to be paid to Indian agent in equivalent Indian
currency as agency commission as applicable will have to be clearly stated in the quotation.
30. After Sales Service : For equipment to be imported the quotation will have to clearly state the available
nearest after sales service centre and contact no. in India.
31. Country of Origin : While Country of Origin Certificate will not be insisted, the same however will have to be
stated in the Original Invoice for payment through LoC.
32. LoC Amendment : LoC/FDD amendment charges due to mistake on the part of the supplier, if any, will have to
be borne by the supplier.
Name : Priyankoo Sarmah, PI
Designation : Assistant Professor
Address : Department of HSS, Academic Complex Block-F, IIT Guwahati, 781039, Assam
Encl.:
ANNEXURE- I
ANNEXURE- II
ANNEXURE- III
ANNEXURE- IV
ANNEXURE- V
ANNEXURE- VI
ANNEXURE- VII
ANNEXURE I
Detailed Technical Specifications for Laptop Computer
Item Name:
Quantity:
Processor
Memory
Weight
Connections
Communications
Audio
Graphics
Storage
Display
Laptop Computer
01(One only)
2.0GHz quad-core Intel Core i7 (Turbo Boost up to 3.4GHz) with 6MB shared L3
cache
8GB of 1600MHz DDR3L
Less than 2.5 KG
SDXC card slot, MagSafe 2 power port, Two USB 3 ports (up to 5 Gbps),
Two Thunderbolt ports (up to 10 Gbps), Headphone port, HDMI port
802.11ac Wi‑Fi wireless networking;3 IEEE 802.11a/b/g/n compatible and
Bluetooth 4.0 wireless technology
Headphone port, Stereo speakers and Dual microphones
Intel Iris Pro Graphics
256 GB
15 inch, LED-backlit
ANNEXURE II
Detailed Technical Specifications for All in One Desktop Computer
Item Name:
Quantity:
Processor
Memory
Storage
Graphics
Display
Audio
Connections
Input
Networking
Weight
Electrical and
operating
requirements
All In One Desktop Computer
01
3.2GHz quad-core Intel Core i5 processor (Turbo Boost up to 3.6GHz) with 6MB L3
cache
8GB (two 4GB) of 1600MHz DDR3 memory; four user-accessible SO-DIMM slots
1TB (7200-rpm) hard drive
NVIDIA GeForce GT 755M graphics processor with 1GB of GDDR5 memory
27-inch (diagonal) LED-backlit display with IPS technology; 2560x1440 resolution
with support for millions of colours
Stereo speakers
Dual microphones
Headphone port
Headphone/optical digital audio output (mini-jack)
SDXC card slot
Four USB 3 ports
Two Thunderbolt ports
Mini Display Port output with support for DVI, VGA and dual-link DVI (adapters
sold separately)
10/100/1000BASE-T Gigabit Ethernet (RJ-45 connector) Kensington lock slot
Keyboard: Full-size keyboard with 12 function keys,
Mouse: Seamless Multi-Touch surface with support for simple gestures (scrolling and
swiping). Ambidextrous construction
802.11n Wi-Fi wireless networking; 2 IEEE 802.11a/b/g compatible Bluetooth 4.0
wireless technology
Less than 12 kg
Line voltage: 100-240V AC
Frequency: 50Hz to 60Hz, single phase
Operating temperature: 10° to 35° C (50° to 95° F)
ANNEXURE III
Detailed Technical Specifications for Dynamic, Close talk head worn microphone
Item Name:
Quantity:
Type:
Transducer Type :
Polar Pattern:
Frequency Response:
Sensitivity (1 kHz):
Dynamic, Close talk head worn microphone
04 (Four only)
Head worn
Dynamic
Cardioid
50 Hz - 15 kHz
65 dBV/Pa / 0,45 mV/Pa
ANNEXURE IV
Detailed Technical Specifications for Headphone
Item Name
Quantity
Transducer Type
Driver size
Sensitivity
Impedance
Max. input power
Frequency range
Net weight (without cable)
Cable length
Type of cable
Plug
Headphone
04(Four only)
Dynamic, Neodym-Magnet
40 mm
101 dB SPL/mW
37 Ω
1000 mW
15 Hz – 27 kHz
Less than 500 g
Less than 2.5 m
Dual-exit, detachable oxygen-free copper
Gold-plated 1/8” (3.5 mm) stereo mini jack
ANNEXURE V
Detailed Technical Specifications for Sound Mixer
Item Name: Sound Mixer
Quantity: 01
FEATURES:
Each mono channel has an Onyx mic preamp, phantom
■ 8-channel premium analog mixer with integrated power, an input Gain control with 60 dB of
gain, a sharp 24-bit / 96 kHz FireWire I/O
18 dB/octave, 75 Hz Low Cut filter, Pan, Mute, Solo and one Channel Insert jack for external
processor connection.
■ Three Onyx boutique quality mic preamps, built-in DIs on the first two channels
■ 3-band Perkins EQ with sweepable mids on mic/line connection of dedicated talkback
channels
section
■ 3-band Perkins EQ on stereo line channels.
■ Hybrid mono/stereo channel with 4-band Perkins EQ
Other features include a stereo tape input and output, a 1/4-inch stereo headphone jack, stereo 12segment LED
■ 8x2 FireWire routing, including aux sends, main meters and XLR and TRS stereo output jacks.
L/R and pre/post EQ assignment for all channels
■ Stereo playback from DAW
■ Built-in DI on first two channels
■ Individual 48V phantom power switches on all mic inputs
■ Talkback section with built in mic and flexible routing
Noise Characteristics: Equivalent Input Noise (EIN), mic input at insert, ISO nsource impedance,
20 Hz to 20 kHz
60 dB (max) gain:
-127 dBu
40 dB gain:
-126.5 dBu
Equivalent Input Noise (EIN), mic input at insert, 50 nsource impedance, A-weighted
60 dB (max) gain: -130.5 dBu
40 dB gain: -130 dBu
Output Noise Figure (1/4” Main out, all channels assigned to main, Gain knobs at unity, 20 Hz to 30
kHz)
Main Mix knob down, channel Level knobs down:
-107 dBu (-Ill dB SNR, ref +4 dBu)
Main Mix knob unity, channel Level knobs down:
-95.5 dBu (-99.5 dB SNR, ref +4 dBu)
Main Mix knob unity, channel Level knobs unity:
-91.5 dBu (-95.5 dB SNR, ref +4 dBu)
FireWire Through (Record + Playback) Dynamic Range: (0 dBu in, mic input to FireWire send, returned
to Control Room, all gain stages at unity, 20 Hz to 20 kHz)
44.1 kHz sample rate: -104 dB
96 kHz sample rate: -106.5 dB
Frequency Response: Mic input to any output (all gain stages at unity, +0/-0.5 dB) 20 Hz to 20 kHz
Stereo channel line input to any output (all gain stages at unity, +0/-0.5 dB) 20 Hz to 20 kHz
FireWire in and out (mic input to FireWire send, returned to Control Room, all gain stages at unity):
44.1 kHz sample rate (+0 1-0.5 dB) 20 Hz to 20 kHz
-3 dB at 21 kHz
96 kHz sample rate (+0/-0.5 dB) 20 Hz to 20 kHz
-3 dB at 45 kHz
Distortion(THD+N):
(20 Hz to 20 kHz bandwi~th
Mic input at insert
(+4 dBu in, 0 dB gain, +4 dBu out) 0.001 %
Mic input at insert
(-36 dBu in, +40 dB gain, +4 dBu out) 0.007%
Stereo channel line input to any output
(+4 dBu in, all gain stages at unity, +4 dBu out) 0.005%
FireWire in and out
(+4 dBu in, mic input to FireWire send, returned to Control Room, all gain stages at unity)
44.1 kHz sample rate: 0.01 %, 20 Hz to 2 kHz
0.02%,2 kHz to 20 kHz
96 kHz sample rate:
0.0 1%, 10Hz to I kHz
0.03%, I kHz to 47 kHz
Attenuation and Crosstalk:
@I kHz
Main Mix knob down -80 dBu
Channel Altl/Mute switch engaged -90 dBu
Channel Level knob down -80 dBu
Common Mode Rejection Ratio (CMRR):
Mic input to insert, max gain, I kHz -70 dB
Maximum Input Levels:
Mic input, gain at min (0 dB) +22 dBu
Mic input, gain at max (60 dB) -38 dBu
Line input, gain at -20 dB +22 dBu
Instrument input, gain at -20 dB +22 dBu
Tape input +12 dBu
Aux return +22 dBu
Maximum Output Levels:
All outputs +22dBu
Equalization:
Mono Channels
Low: ±15 dB @ 80 Hz
Mid frequency: 100 Hz to 8 kHz
Mid gain: ±15 dB
High: ±15 dB @ 12 kHz
Hybrid Channel
Low: ±15 dB @ 80 Hz
Low Mid: ±15 dB @ 400 Hz
High Mid: ±15 dB @ 2.5 kHz
High: ±15 dB @ 12kHz
Stereo Channels
Low: ±15 dB @ 80 Hz
Mid: ±15 dB @ 2.5 kHz
High: ±15 dB @ 12 kHz
FireWire:
Sample Rates Available 44.1 kHz, 48kHz,
88.2kHz, 96kHz
Buffer Size
32(44. 1kHz and 48kHz only), 64,
128,256,512,1024,2048 samples
24- bit
Resolution
Meters:
2-segment pre-fader channel meters OL (+ 18 dBu), -20 dBu
12-segment pre-fader Control Room meters OL (+20 dBu), +15, +10, +6, +3, 0, -2, -4, -7, -10, -20,30 (0 dB = 0 dBu)
Input Impedance:
Mic input 2.8 Ω k balanced
Hi-Z input I M Ω unbalanced
Mono channel line input: 30 Ω k balanced
15 Ω k unbalanced
Stereo channel line input: 20 Ω k balanced
10 Ω unbalanced
Output Impedance
Main XLR output: 100 Ω balanced
Phones output: 75 Ω
All other outputs: 300 Ω
ANNEXURE VI
Detailed Technical Specifications for Dynamic double ribbon microphone
Item Name: Dynamic double ribbon microphone
Quantity:01(one only)
Transducer type: Dynamic
Operating principle: Pressure gradient
Frequency response: 40 - 18,000 Hz
Polar pattern: Hypercardioid
Rear attenuation at 1 kHz : > 25 dB at 110°
Open circuit voltage at 1 kHz
(0 dB = 1 V/Pa) 1.0 mV/Pa = -60 dBV
Nominal impedance: 200 Ω
Load impedance: ≥ 1000 Ω
Diaphragm: aluminum
Case/finish: Brass
Connector: 3-pin XLR male
Dimensions: Length: 156 mm
Shaft diameter: 23 mm
Head diameter: 38 mm
Weight without cable: 156 g
ANNEXURE VII
Detailed Technical Specifications for Portable Digital Recorder
Item name: Portable digital recorder
Quantity: 04(Four only)
Recording Media: SD card(64MB~2GB), SDHC card (4GB~32GB)
File Format: WAV, MP3
Recording/Playback Format: WAV 44.1/48/96 (HS mode) kHz, 16/24-bit
Number of Channels: 2 channels (stereo)
Analog Input: MIC/LINE 1 IN (XLR), 1/8"(3.5mm)stereo mini jack
Analog Output: LINE OUT 1/8"(3.5mm)stereo mini jack
Headphone Output: 1/8"(3.5mm)stereo mini jack
Power Supply: Lithium-ion rechargeable battery
Frequency response: 20-20000 Hz
Computer Requirements: Windows OS Windows XP, Macintosh OS Mac OS X 10.2 or later
USB Port: USB2.0 recommended
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement